An innovative wireless sensor network (WSN) based on Ultra-Wide Band (UWB) technology for 3D accurate superficial monitoring of ground deformations, as landslides and subsidence, is proposed. The system has been designed and developed as part of an European Life+ project, called Wi-GIM (Wireless Sensor Network for Ground Instability Monitoring). The details of the architecture, the localization via wireless technology and data processing protocols are described. The flexibility and accuracy achieved by the UWB two-way ranging technique is analysed and compared with the traditional systems, such as robotic total stations (RTSs), Ground-based Interferometric Synthetic Aperture Radar (GB-InSAR), highlighting the pros and cons of the UWB solution to detect the surface movements. An extensive field trial campaign allows the validation of the system and the analysis of its sensitivity to different factors (e.g., sensor nodes inter-visibility, effects of the temperature, etc.). The Wi-GIM system represents a promising solution for landslide monitoring and it can be adopted in conjunction with traditional systems or as an alternative in areas where the available resources are inadequate. The versatility, easy/fast deployment and cost-effectiveness, together with the good accuracy, make the Wi-GIM system a possible solution for municipalities that cannot afford expensive/complex systems to monitor potential landslides in their territory.

Since surface relief transmission gratings have very strict requirements on operators and use environment, according to the semiconductor laser external cavity spectral beam combining system, this paper proposes a design scheme of semiconductor laser array spectral beam combining system based on grating-external cavity. The finite element approach was used to create a wideband, high-efficiency fill-in multilayer dielectric transmission grating structure for a high-power spectrum beam combining system. The incidence angle, ridge height, duty cycle, and sidewall inclination angle of the transmission grating were tuned and evaluated, and a link between the transmission grating's diffraction efficiency and grating characteristics was discovered. The calculated design of the high-power fused silica transmission grating has a negative first-order peak diffraction efficiency of 99.5% in the 800nm range. In the spectral region of 765-872 nm, the transmission grating's diffraction effectiveness exceeds 92%. The filled ultra-high diffraction efficiency multilayer dielectric transmission grating design addresses the issue of resistance to high-power lasers under complicated operating settings, it’s intended to maintain a high diffraction efficiency even after several cleaning cycles, and it’s an ideal component for high-power spectrum beam combining systems.

To achieve a narrow bandwidth optical filter with a wide swept range for new generation optical spectrum analysis (OSA), an optoelectronic equivalent narrowband filter (OENF) is investigated and a swept optical filter with bandwidth of several MHz and swept range of several ten nanometers is built using electric filters and a swept laser as local oscillator (LO). The principle of OENF is introduced and analysis of OENF system is presented. Two electric filters are optimized to be RBW filters for high and medium spectral resolution application. Both simulations and experiments are conducted to verify OENF principle and results show that power uncertainty is less than 1.2% and spectral resolution can reach 6 MHz. Then, a real-time wavelength calibration system consisting of HCN gas cell and FP etalon is proposed to guarantee a wavelength accuracy of ±0.4 pm at C-band and to reduce the influence of phase noise and nonlinear velocity of swept LO. Finally, experiments on OSA of actual spectra of various optical sensors using OENF system are conducted. Experimental results indicate that OENF system has an excellent capacity in analysis of fine spectrum structures.

In this short communication, we conducted first-principles calculations to explore the stability of boron monochalcogenides (BX, X=S, Se or Te), as a new class of two-dimensional (2D) materials. We predicted BX monolayers with two different atomic stacking sequences of ABBA and ABBC, referred in this work to 2H and 1T, respectively. Analysis of phonon dispersions confirm the dynamical stability of BX nanosheets with the both 2H and 1T atomic lattices. Ab-initio molecular dynamics simulations reveal the outstanding thermal stability of all predicted monolayers at high temperatures over 1500 K. BX structures were found to exhibit high elastic modulus and tensile strengths. It was found that BS and BTe nanosheets can show high stretchability, comparable to that of the graphene. It was found that all predicted monolayers exhibit semiconducting electronic character, in which 2H structures present lower band-gaps as compared with 1T lattices. The band-gap values were found to decrease from BS to BTe. According to the HSE06 results, 1T-BS and 2H-BTe show respectively, the maximum (4.0 eV) and minimum (2.06 eV) electronic band-gaps. This investigation introduces boron monochalcogenides as a novel class of 2D semiconductors with remarkable thermal, dynamical and mechanical stability.

K-band radar waves have high penetration and low attenuation coefficients. However, the wavelength of this radar wave is relatively short; thus, designing and preparing both broadband and wide-angle radar wave absorbers in this band presents considerable challenges. In this study, a resin-based K-band radar wave absorber with a biomimetic lotus leaf structure was designed and formed by UV curing. Here, microscale lotus leaf papillae and antireflection structures were prepared using a DLP 3D printer, and the contact angle between the material and water droplets was increased from 56° to 130°. In addition, the influence of the geometric parameters of the lotus leaf antireflection structure on the electromagnetic absorption performance and mechanical strength was investigated. After simulation optimization, the maximum electromagnetic loss of the lotus leaf structure 3D printed sample was −32.3 dB, and the electromagnetic loss was below −10 dB in the 20.8–26.5 GHz frequency range. When the radar incidence angle was 60°, the maximum electromagnetic loss was still less than −10 dB. The designed lotus leaf structure has a higher mechanical energy absorption per unit volume (337.22 KJ/m3) and per unit mass (0.55 KJ/Kg) than commonly used honeycomb lightweight structures during the elastic deformation stage, and we expect that the designed structure can be used as an effective lightweight material for K-band radar stealth.

Millimeter wave wide-band imaging is widely studied for a variety of applications. However real-time millimeter wave wide-band imaging at frequencies above 30GHz for moving targets in a large field of view has not been realized commercially. A 2D sparse array with transmitter multiplexing is a promising solution to this problem. In this article, a method combining compressed sensing and orthogonal coded multiplexing was proposed, and the imaging performance was analyzed for different reconstruction algorithms and observation matrices by imaging simulation for a continuous object. Also the influence on the dynamic range of the original signal introduced by orthogonal coded multiplexing was studied. This work demonstrated that the proposed method was effective in reconstructing the image with a real-time capability. It is shown that different algorithms and matrices resulted in distinct performances, while the evaluation parameter selection also played a role. This work provided useful instructions for both the hardware and software design of a real-time 3D millimeter wave imaging system in the future.

Butler matrix networks are well established as beam forming networks for phased antenna arrays. The challenge we address in this work is to cover the entire, (advanced 5G or 6G), FR3 band (7-24 GHz) with a single network, while retaining low losses and minimal size. The employed multilayer topology is also well established, however, the matching between the utilized hybrid couplers and the phase shifters constitutes a major challenge for such a wideband operation. This is achieved herein employing meander lines with appropriate curvature and introducing two distinct design methods for the Butler Matrix. The first method focuses on designing individual components separately, followed by their integration into the overall Butler Matrix structure. This approach is demonstrated through the design, prototyping, measurements and validation of an 8x8 Butler Matrix beamformer, which operates across the 6-16 GHz band (FR3 Low). The second method introduces a wideband matching technique, which simplifies the implementation process by designing the Butler Matrix as a single, unified structure. This technique is applied to both 4x4 and 8x8 Butler Matrices, which are implemented and simulated for the low FR3 band. Both design methods result in wideband operation, compact size, and meet the desired performance criteria.

In order to correct attenuated millimeter-wavelength (Ka-band) radar data and address the problem of instability, an attenuation correction methodology (attenuation correction with variation trend constraint; VTC) was developed. Using synchronous observation conditions and multi-band radars, the VTC method adopts the variation trends of reflectivity in X-band radar data captured with wavelet transform as a constraint to adjust reflectivity factors of millimeter-wavelength radar. The correction was evaluated by comparing reflectivities obtained by millimeter-wavelength cloud radar and X-band weather radar. Experiments showed that attenuation was a major contributory factor in the different reflectivities of the two radars when relatively intense echoes exist, and the attenuation correction developed in this study significantly improved data quality for millimeter-wavelength radar. Reflectivity differences between the two radars were reduced and reflectivity correlations were enhanced. Errors caused by attenuation were eliminated, while variation details in the reflectivity factors were retained. The VTC method is superior to the bin-by-bin method in terms of correction amplitude and can be used for attenuation correction of shorter wavelength radar assisted by longer wavelength radar data.

Ultra-wide field optical coherence tomography (UWF-OCT) has been recently introduced into clinical ophthalmological practice. To date, there is little data on the reference values of retinal thickness (RT) and choroidal thickness (CT) measured with this technique. This study aimed to analyze the variance of RT and CT in healthy eyes with UWF-OCT tests performed with the largest available scan size of 23 x 20 mm. The data were analyzed with reference to the patients' age, gender, and the axial length of the eyeball. The results of UWF-OCT scanning enabled us to picture the shape of the retina and choroid in a large portion of the eyeball. Both anatomical entities become significantly thinner at the periphery. The peripheral CT is greater in the upper and temporal sectors; the RT is higher in the nasal compared to the temporal sectors. Both choroid and retina lose thickness with age, however, CT and RT do not show a statistically significant correlation with the axial length after adjusting for age and gender. Age-related variations in thickness are especially prominent in the choroid. The CT in UWF-OCT testing is significantly greater in females while the RT is greater in males. UWF-OCT testing provides additional information on the anatomical structure of the retina and choroid compared to standard-field OCT

The electronic structure and some of its derived properties of Li2CaGeO4 compound have been investigated. The calculations have been performed using the full-potential linearized augmented plane wave plus local orbitals method and ultra-soft pseudo-potentials . The optimized lattice parameters are found to be ingood accord with experiment. Features such as bulk modulus and its pressure derivative, electronic band structure and density of states are reported. The elastic anisotropy of the crystal is discussed and visualized. Moreover, the optical properties reveal that Li2CaGeO4 compound are suitable candidates for optoelectronic devices in the visible and ultraviolet (UV) regions.

The generation of high-quality wideband frequency sweeps presents a significant challenge, particularly in modern telecommunication, radar, and measurement systems where miniaturization is paramount. While phase-locked loops (PLLs) have become the dominant technique for signal generation, their application in broadband sweeps necessitates fractional-N operation. This, in turn, degrades phase noise and introduces unwanted spurs. This paper proposes a novel approach for broadband signal generation. By cascading two PLLs and utilizing a coaxial resonator, we achieve a high-performance oscillator that operates without the excessive fractional spurs, maintaining their level below -80 dBc across the entire frequency band. The prototype demonstrates non-degraded phase noise performance, reaching -102 dBc/Hz at 100 kHz offset and -121 dBc/Hz at 1 MHz offset for signal at 10 GHz. Despite significant frequency jumps, our design achieves lock times below 41 µs. These results, supported by theoretical analysis, validate the proposed method's effectiveness in generating low-noise broadband frequency sweeps, ideal for local oscillator applications.

Retails and shopping centers have become essential to today’s lifestyle. Furthermore, as modern shopping venues, retail centers' social role contributes to its popularity and profitability. The social motive of customers for shopping is beyond acquiring their crucial purchases. These advantages favor retail centers and improve the level of social sustainability and its relevant concepts. Given that relatively little study has been studied on the impact of retail centers' social role as places for interactional and recreational activities on customers' behavior in these centers and its relation to social sustainability. Two hypotheses were raised that show the effect of time travel duration and shop variety on increasing the percentage of users who spend their leisure time and recreational activities in two analogous retail centers. The result of research regarding the first hypothesis reveals that there is an interaction between time travel duration and shoppers' motivation. Furthermore, the results revealed that half of both retail center goers who spend more than 10 minutes to arrive at the retail centers prefer to do leisure activities and browsing than shopping. Therefore, the majority of individuals are from further distances, indicating longer trips can be one of the factors for willing to spend more leisure time and recreational activities. The second hypothesis reveals that shop variety can be one of the main reasons for attracting users to spend their leisure time and browse in both retail centers. There is a significant correlation between shop variety and customers’ motivation.

The main purpose of this paper is to propose a novel optimization model with a new machine learning approach in the first section to achieve the best results in financial institutions in the second section. Since the constancy of efficacy derived from parametric and non-parametric is not significant, this paper provides a scientific assessment at the optimization section and proposes a novel combined parametric and non-parametric model which will be a new experiment in literature perception. A scientific assessment of banks based on a combination of the efficiency measurement method of CCR(Charnes, Cooper and Rhodes model) or CRS(Constant Return to Scale) BCC(Banker, Charnes, and Cooper model) or VRS (Variable Return to Scale) in Data Envelopment Analysis (DEA), as well as Stochastic Frontier Approach (SFA) for 65 banks during Feb to July 2020, are introduced. For analyzing the performance of the parametric and non-parametric approaches we have considered the linear regression and Unreplicated Linear Functional Relationship (ULFR). At the machine learning section, a novel four-layers data mining filtering pre-processes for selected supervised classification as well as unsupervised clustering algorithms to increase the accuracy and to remove unrelated attributes and data are applied. For the four kinds of preprocessing approaches of unsupervised attributes, supervised attributes, supervised instances, and unsupervised instances, we have chosen discretization, attribute selection, stratified remove folds, and resample filters respectively. Based on the nature of the suggested financial institution's dataset and attributes, the most appropriate preprocessing filter in each layer to achieve the highest performance is suggested. Finally, the superior bank, best performance model, and the most accurate algorithm are introduced. The results indicate that the bank number 56 is the superior bank. Among the proposed techniques, the novel recommended CVS compared with CCR-BCC and SFA models, has a more positive correlation with profit risk, and show a higher coefficient of determination values. Sequential Minimal Optimization(SMO) algorithm receives the highest accuracy in all four suggested filtering layers.

Oligopeptide transporters (OPTs) are a group of membrane localized proteins that have a broad range of substrate transport capabilities and contribute to numerous biological processes. However, limited information has been reported on OPTs in higher plants. In this study, a comprehensive analysis of the OPT gene family in Medicago truncatula was performed. A total of 26 OPT genes (MtOPT01-MtOPT26) have been identified in the Medicago truncatula genome. Phylogenetic analyses indicated that MtOPTs consisted of two distinct subgroups, 12 MtOPTs belonged to the peptide transport subgroup (PT-OPT) based on their predicted amino acid sequences containing the two highly conserved motifs (NPG and KIPPR) and 14 MtOPTs belonged to yellow stripe subgroup (YS-OPT). The MtOPTs distributed on each of 8 chromosomes in Medicago truncatula. Sequence analysis verified that MtOPTs significant similar to those in other plants. The copy number of MtOPTs was low and the multiply of MtOPTs was simple relatively. Gene structure analysis showed that most of the MtOPTs have various numbers of introns. The multiple of MtOPTs might play different biological roles which were supported by the fact that MtOPTs have a distinct tissue-specific expression pattern. The data obtained in this study will help to better understand the complexity of the MtOPTs gene family and provide new evidence for the function and evolution of the OPT gene family in higher plants.

Reinforcement learning (RL) is an extensively applied control method for the purpose of designing intelligent control systems to achieve high accuracy as well as better performance. In the present article, the PID controller is considered as the main control strategy for brushless DC (BLDC) motor speed control. For better performance, the fuzzy Q-learning (FQL) method as a reinforcement learning approach is proposed to adjust the PID coefficients. A comparison with the adaptive PID (APID) controller is also performed for the superiority of the proposed method, and the findings demonstrate the reduction of the error of the proposed method and elimination of the overshoot for controlling the motor speed. MATLAB/SIMULINK has been used for modeling, simulation, and control design of the BLDC motor.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

Recent studies investigated the detectability of ship wake signatures on SAR imagery using a large number of SAR images collocated with Automatic Identification System data for training machine learning models. These detectability models are in agreement with oceanographic expectations from preceding studies and can therefore be used for comparing the performance of different SAR sensors in terms of wake detectability. Previous model comparisons showed better wake detection performance of TerraSAR-X (TS-X) than of RADARSAT-2 (RS2) and Sentinel-1 (S1). A comparison between CosmoSkymed (CSK) and RS2 is performed here, to examine the hypothesis that X-Band is generally better for wake detection than C-Band. Finally, this hypothesis is not confirmed, as the detectability models for TS-X, CSK and RS2 reveal similar performances. A comparison of wake detection performance should take the individual wake components into account separately.

Triangular resonators re-shaped with the Sierpinski geometry and U-shaped resonators have been designed, linking them with single-pole-double-through (SPDT) RF MEMS switches to provide frequency tuning for potential applications in the K-Band. Prototypes of band-stop narrowband filters working around 20 GHz and 26 GHz, interesting for RADAR and satellite communications, have been studied in coplanar waveguide (CPW) configuration, and the tuning was obtained by switching between two paths of the devices loaded with different resonators. As a result, dual-band operation or fine-tuning can be obtained depending on the choice of the resonator, acting as a building block. The studied filters belong to the more general group of devices inspired by the metamaterial design.

The aim of this study is to solve the problems of complicated pretreatment and high analytical cost in the detection technology of trace drug toxicants in municipal wastewater. A high-performance magnetic sorbent was synthesized for enrichment of trace drug substances in wastewater to develop magnetic solid-phase extraction pretreatment combined with the acoustic ejection mass spectrometry (AEMS) analytical methods for the molecules in wastewater drug toxicants. The magnetic nanospheres was successfully prepared by magnetic nanoparticles modified with divinylbenzene and vinyl pyrrolidone.The results showed that the linear dynamic range of 17 drugs was 1-500 ng/L, the recovery was 43%-105%, the matrix effect was more than 67%, the limit of quantitative detection was 1-2 ng/L, and the detection time of each sample was 2.98s. It can be seen that the developed magnetic solid-phase extraction (MSPE) method is a good solution to the problem of complicated pre-treatment and analytical cost in the detection of drugs in wastewater. The developed magnetic material and acoustic excitation coupled mass spectrometry analysis method can realize the low-cost, efficient enrichment and fast analysis of different kinds of drug molecules in urban sewage.

Weak signal spectral detection is a serious problem in many applications, especially the target possesses certain frequency band and under low signal-to-noise ratio (SNR). A kind of novel technique based on pre-whitening scale-transformation symmetric bistable parallel stochastic resonance (SR) is proposed to solve the problem. Firstly, the pre-whitening can ensure the even distribution of the receiving signal to fit the requirement of SR processing. Secondly, the scale- transformation can help to utilize the weak signal improvement property especially under low frequency band more effectively. Thirdly, the symmetric bistable parallel SR can try to reduce the variance of the clutter and additive noise fluently. Fourthly, by subtracting the steady state re-sponse of the selected symmetric bistable SR system from the parallel SR output, the weak signal spectral detection objective can be realized successfully. Simulation results based on the real sea clutter radar data guarantee the effectiveness and applicability of the proposed symmetric bistable PSR processing approach.

Emotion recognition defined as identifying human emotion and is directly related to different fields such as human-computer interfaces, human emotional processing, irrational analysis, medical diagnostics, data-driven animation, human-robot communi- cation and many more. The purpose of this study is to propose a new facial emotional recognition model using convolutional neural network. Our proposed model, “ConvNet”, detects seven specific emotions from image data including anger, disgust, fear, happiness, neutrality, sadness, and surprise. This research focuses on the model’s training accuracy in a short number of epoch which the authors can develop a real-time schema that can easily fit the model and sense emotions. Furthermore, this work focuses on the mental or emotional stuff of a man or woman using the behavioral aspects. To complete the training of the CNN network model, we use the FER2013 databases, and we test the system’s success by identifying facial expressions in the real-time. ConvNet consists of four layers of convolution together with two fully connected layers. The experimental results show that the ConvNet is able to achieve 96% training accuracy which is much better than current existing models. ConvNet also achieved validation accuracy of 65% to 70% (considering different datasets used for experiments), resulting in a higher classification accuracy compared to other existing models. We also made all the materials publicly accessible for the research community at: https://github.com/Tanoy004/Emotion-recognition-through-CNN.

In this paper, single and repetitive frequency UIS characteristics of 1200 V asymmetric (AT)and double trench silicon carbide (DT-SiC) metal–oxide-semiconductor field-effect transistors (MOSFETs) under different working conditions are investigated by experiment and simulation. For asymmetric trench SiC MOSFETs, the failure mode is all thermal runaway under working conditions. However, the failure mode of double trench SiC MOSFETs mostly is gate oxide rupture, which indicates an instable avalanche robustness under UIS stress. The variations of measured parameters are recorded to evaluate typical electrical features of device failure. Furthermore, TCAD simulation is used to reveal the electro-thermal stress inside the device during avalanche. Additionally, failed devices are decapsulated to verify the location of failure point from the perspective of the semiconductor die. Finally, a new type of stepped-oxide vertical power DT MOSFET with P-type shielding and current spread layers is proposed for improvement of gate dielectric reliability.

The aim of this study was to examine the oxidation of human serum albumin (HSA) caused by oxidative stress after an exhaustive exercise such as ultra-marathon race. Thus, blood samples from 12 adult runners who underwent a 103 km mountain ultra-marathon race were collected pre- and 24, 48 and 72 h post race. HSA was partially purified using affinity chromatography and then was subjected to Western blot analysis for disulfide dimers determination, indicating oxidation. The results were correlated with those from a previous study in which the same samples were analyzed using different oxidative stress markers and a good correlation with protein carbonyls (PC) at all time points was observed. Moreover there was a significant correlation with static oxidation-reduction potential (sORP) at 24 h, and a negative correlation with capacity oxidation-reduction potential (cORP) at 24 and 48 h. In addition, an individual analysis of albumin dimers exhibited great inter-individual differences. This inter-individual variability in the oxidation of HSA may suggest different interventions (e.g. through diet) in order to confront the effects on athletes’ organism after a strenuous exercise. In conclusion, this study supported the importance of the assessment of albumin dimers as a predictive marker for exercise-induced oxidative stress.

A novel nano-laminated GdB2C2 material was successfully synthesized using GdH2, B4C, and C via an in-situ solid state reaction approach for the first time. The formation mechanism of GdB2C2 was revealed based on the microstructure and phase evolution investigation. A purity of 96.4 wt. % GdB2C2 was obtained at a low temperature of 1500 ℃, while a near full pure GdB2C2 can be obtained at a temperature over 1700 ℃. The as-obtained GdB2C2 presented excellent thermal stability at high temperature of 2100 ℃ in Ar atmosphere due to the stable frame work formed by the high covalent four-members and eight-members B-C rings in GdB2C2. The minimum reflection loss value (RLmin) of -47.01 dB with an effective absorption bandwidth (EAB) of 1.76 GHz at a thickness of 3.44 mm was obtained for the GdB2C2 synthesized at 1500 ℃. The possible EMWA mechanism could be ascribed to the nano-laminated structure and appropriate electrical conductivity, which facilitated to the good impedance matching, remarkable conduction loss, interfacial polarization as well as multiple interface reflection and scattering. The as-obtained GdB2C2, with excellent EMWA performance as well as remarkable ultra-high temperature thermal stability, could be a promising candidate for the EMWA materials applications in extreme ultra-high temperatures.

Callus induction (CI) is the critical trait for the transformation of desirable genes in plants. A genome-wide association study (GWAS) analysis was conducted on the rice germplasm of 110 diverse indica rice accessions. Three tissue culture media, including B5, MS, and N6, were used for CI in those rice panels. Seven quantitative trait loci (QTLs) on chromosomes 2, 6, 7, and 11 were found to confer a CI percentage in these three media. For the B5 medium, one QTL (qCI-B5-Chr6) was identified on the rice chromosome 6. For the MS medium, two QTLs were identified on the rice chromosomes 2 and 6 (qCI-MS-Chr2 and qCI-MS-Chr6, respectively). For the N6 medium, four QTLs were identified on the rice chromosomes 6, 7, and 11 (qCI-N6-Chr6.1, qCI-N6-Chr6.2, qCI-N6-Chr7, and qCI-N6-Chr11, respectively). Fifty-five genes were identified within the haplotype blocks corresponding to these QTLs. Thirty-one genes showed haplotypes associated with different CI in those media. The qCI-B5-Chr6 was located in the same region as the qCI-N6-Chr6.2. The caleosin-related family protein was identified in this region. Analysis of the gene-based haplotype reveals the association of this gene with different CI in both B5 and N6 media, suggesting that the gene may play a critical role in the CI mechanism. Moreover, several genes, including the beta-tubulin, the zinc finger proteins, the RNP-1 domain-containing protein, and the Lysophosphatidic acid acyltransferase, were associated with different CI in the N6 media. Results from this study provide insight into the potential QTLs and candidate genes for callus induction in rice that will fulfill the understanding of the physiological and biochemical processes involved in callus formation, which is an essential tool in the molecular breeding of rice.

Landiolol is an ultra-short-acting, selective ß1- adrenergic receptor blocker that was originally approved by Japan for the treatment of intraoperative tachyarrhythmias. It has gained attention for its use in the management of tachyarrhythmias and perioperative tachycardia, especially atrial fibrillation for both cardiac and non-cardiac surgeries. It can be the ideal agent for heart rate control due to its high β1‐selectivity, the potent negative chronotropic effect, a limited negative inotropic potential, and an ultrashort elimination half‐life (around 4 min); moreover, it may have a potential therapeutic effect for sepsis and pediatric patients. Landiolol seems to be superior to other short‐acting and selective beta‐blockers such as esmolol. This review aims to provide a comprehensive overview of landiolol, a new ultra-short-acting ß1 selective antagonist, including its pharmacology, clinical applications, efficacy, safety profile, and future directions in research and clinical data.

A large core size and bending resistance are very important properties of mid-infrared energy transfer fibers, but large core sizes usually lead to a deterioration of bending properties. A negative-curvature nested node-free anti-resonant hollow-core fiber (AR-HCF) based on quartz is proposed. It was made by adding a nested layer to a previous AR-HCF design to provide an additional anti-resonance region while keeping the gap between adjacent tubes strictly correlated to the core diameter to produce a node-free structure. These features improve the fiber’s bending resistance while achieving a larger core diameter. The simulation results show that the radial air-glass anti-resonant layer is increased by the introduction of the nested anti-resonant tube, and the weak interference overlap between the fiber core and the cladding mode is reduced, so the fiber core’s limiting loss and the sensitivity to bending are effectively reduced. When the capillary wall thickness t of the fiber is 0.71 μm, the core diameter D is 70 μm, the ratio of the inner diameter of the cladding capillary to the core diameter d/D is 0.62, and the diameter of the nested tube is d0=29 μm, the fiber has a lower limiting loss at the wavelength of 2.79 μm, and the limiting loss is 3.28×10-4 dB/m. At the same time, the optimized structure also has good bending resistance. When the bending radius is 30 mm, the bending loss is only 4.72×10-2 dB/m. To our knowledge, this is the first research to achieve an anti-bending low-loss micro-structure hollow fiber with a bending radius of less than 30 mm in the 2.79 μm band. An anti-bending low-loss anti-resonant hollow-core fiber with this structure constitutes a reliable choice for the light guiding system of a 2.79 μm band erbium laser therapy instrument.

In this paper any superalgebra is generalized to a new form, namely ultra algebra. We study some algebraic structure results for ultra algebras and we have defined some maps on ultra algebras to know ultra derivation and Jordan ultra derivation. Moreover on certain assumptions we have proved that Jordan ultra derivation is an ultra derivation.

An accurate outbreak prediction of COVID-19 can successfully help to get insight into the spread and consequences of infectious diseases. Recently, machine learning (ML) based prediction models have been successfully employed for the prediction of the disease outbreak. The present study aimed to engage an artificial neural network-integrated by grey wolf optimizer for COVID-19 outbreak predictions by employing the Global dataset. Training and testing processes have been performed by time-series data related to January 22 to September 15, 2020 and validation has been performed by time-series data related to September 16 to October 15, 2020. Results have been evaluated by employing mean absolute percentage error (MAPE) and correlation coefficient (r) values. ANN-GWO provided a MAPE of 6.23, 13.15 and 11.4% for training, testing and validating phases, respectively. According to the results, the developed model could successfully cope with the prediction task.

The ZIPs (ZRT/IRT-like proteins) play critical roles in the absorption, transport, and intracellular balance of metal ions essential for various physiological processes in plants. However, little is known about the pan-genomic characteristics and properties of ZIP genes in cucumber (Cucumis sativus L.). In this study, we identified 10 CsZIP genes from the pan-genome of 13 C. sativus accessions. Among them, only CsZIP10 showed no variation in protein sequence length. We analyzed the gene structure, conserved domains, promoter cis-elements, and phylogenetic relationships of these 10 CsZIP genes derived from "9930". Based on phylogenetic analysis, the CsZIP genes were classified into three branches. Amino acid sequence comparison revealed the presence of conserved histidine residues in the ZIP proteins. Analysis of promoter cis-elements showed that most promoters contained elements responsive to plant hormones. Expression profiling in different tissues showed that most CsZIP genes were expressed at relatively low levels in C. sativus leave, stem, and tendril, and CsZIP7 and CsZIP10 were specifically expressed in root, indicating their potential involvement in the absorption and transport of metal ions. Transcriptomic data indicated that these 10 ZIP genes displayed responses to both downy mildew and powdery mildew, and CsZIP1 were significantly downregulated after both salt and heat treatments. In conclusion, this study deepens our understanding of the ZIP gene family and enhances our knowledge of the biological functions of CsZIP genes in C. sativus.

The band gap research in graphene is still a very important topic for materials application. Here, we report a band gap opening and p-type semiconducting property of the graphene by using an electrochemical doping on graphene surface. The manganese-oxide nanopar-ticles adsorbed on the graphene were used as the dopants in an electrolyte, which induce the band gap opening and the change of electronic structure. In addition, the fabricated graphene FET shows the p-type semiconductor behaviors. The temperature dependent conductivity of the p-type doped graphene at applied potential of 1.5 V during electro-chemical doping shows the formation of band gap of 0.23 eV, which is obtained from the fitting of conductivity equation. The semiconducting properties of manganese-oxide doped graphene is attributed to the formation of manganese-oxide nanoparticle on the surface of graphene.

Abstract: Polylactic acid (PLA) is brittle in nature with extensive deformation property. For improvement of the end-use quality, it is of significant importance to enhance the producibility of fused deposition modeling (FDM)-printed objects in PLA. The purpose of this investigation is to boost toughness and to reduce the production cost of the FDM-printed tensile test samples with the desired part thickness. To attain the research purpose number of experiments are designed and analyzed by the Response Surface Method (RSM). The statistical analysis is performed to deal with this concern considering layer thickness, infill percentage, and extruder temperature as controlled factors. The tensile test specimens are printed based on the designed experiments, and the tensile strength tests are conducted by SANTAM 150 universal testing machine based on ASTM D638. The honeycomb internal fill pattern is applied for the production of light-weight and high-strength specimens. The area under Force- Extension curve up to fracture is acquired as the toughness of the printed specimens. This study also developed a modeling process using ANN and ANN-GA techniques for developing an accurate estimation for toughness, part thickness, and production cost as dependant variables. Results were evaluated by correlation coefficient and RMSE values. According to the modeling results, ANN-GA as a hybrid ML technique could successfully improve the accuracy of modeling about 7.5, 11.5 and 4.5 % for toughness, part thickness, and production cost, respectively, in comparison with those for the single ANN method. In the other side, the optimization results confirm that the optimized specimen is cost-effective and able to comparatively undergo deformation, which develops the usability of printed PLA objects. The research is accomplished under the constraints of PLA compatibility with existing fused deposition modeling setup without changing the functional hardware/software of the machine. Although the mechanical properties and dimensional accuracy of PLA have already been studied, there is little literature on the toughness of the printed PLA with honeycomb internal fill pattern.

Consumption of ultra-processed foods is associated with abdominal obesity, but this association has not yet been investigated in individuals on hemodialysis. This cross-sectional study, developed with 1014 individuals, aimed to analyze the prevalence of abdominal obesity and its association with the consumption of ultra-processed foods in individuals on hemodialysis. Consumption of ultra-processed foods was measured using a questionnaire, whose list of foods was based on the Surveillance System of Risk and Protective Factors for Chronic Non-Communicable Diseases through Telephone Enquiry. Waist circumference was used to determine the presence of abdominal obesity. The difference in proportions between the independent variables and the outcome was verified using Pearson's chi-square test. Hierarchical logistic regression was used to determine the association between the outcome and the independent variables. The prevalence of abdominal obesity was 77.22%. In the final model, higher consumption of ultra-processed foods, be male and an adult, have between 8 and 11 years of schooling and practice physical activity below the recommended level increased the chances of having abdominal obesity. The research provides a basis for the creation and improvement of public policies that promote improvements in these health determinants.

Possibilities of utilization of two frequencies synthetic aperture radar (SAR) operating simultaneously in P-band and S or L-band are considered. Advantages of such system are shown. They are caused by improvement of data interpretation and by decrease of ionosphere influence. Tasks of surface and subsurface sensing by the complex SAR were under investigation for vegetation, soil covers are given. As an example, the investigation results of coniferous forest areas backscattering by the spaceborne P-band SAR together with L-band SAR in the September-February period are presented. Studies have shown that the joint use of the results in L and P bands offer unique opportunities to explore the effects of changes in the backscattering properties of forest surfaces.

As high strength and ultra-high strength steels are widely used in all kinds of modern welded constructions, a lot of research is carried out to investigate the mechanical properties of weldments of these steels but there is a scarce information on such important characteristic as their corrosion behaviour. This research focuses on the corrosion behaviour of weld metal of weldments of S906QL and S700MC steels. Weld metal was tested electrochemically in a 3,5% NaCl aqueous solution via potentiodynamic scan to determine corrosion rate and its dependence on welding gap. No influence of welding gap on corrosion rate was found but the experimental results suggested that corrosion rate depended on the chemical composition of filler material and the microstructure of weld metal.

In this letter, we propose a pattern-diversity antenna with different radiation patterns at two different frequency bands (f1 and f2) (f1: broadside radiation pattern, f2: conical radiation pattern). The proposed structure consists of a central circular antenna and two annular ring antennas; each of the three antennas has individual ports. Two of the ports exhibit orthogonal broadside radiation patterns; the other two ports exhibit orthogonal conical radiation patterns. Thus, they have polarization diversity characteristics. To improve isolation between ports, the inner part of the annular ring antennas is shorted via array, and the outermost port is positioned orthogonal to the other ports. Using this configuration, the isolation between ports was measured as -26.7 dB and -30.1 dB at the two frequency bands, respectively. Experimental results based on the fabricated prototype show that the proposed antenna achieves -10 dB bandwidths of 240 MHz (5.71~5.95 GHz) and 210 MHz (7.69~7.9 GHz) at f1 and f2, respectively.

Background/Objectives: Direct oral anticoagulants (DOACs) are first-line medications for stroke prevention in non-valvular atrial fibrillation (AF). However, variability in drug response poses risks of hemorrhagic or thromboembolic events. The role of genetics in determining DOAC safety is gaining attention, but evidence linking specific genetic polymorphisms to bleeding risk is lacking. Therefore, the aim of our study was to conduct an Exome-Wide Association Study with 198 non-valvular AF patients treated with rivaroxaban or apixaban, including 97 with bleeding complications and 99 without. Methods: DOAC plasma concentrations, 6-β-hydroxycortisol and cortisol levels in urine were measured for CYP3A4 phenotyping. Sequencing was performed on the DNBSEQ G-400 platform. Single nucleotide variants (SNV) associations with bleeding risk were assessed using logistic regression with additive, dominant, and recessive genetic models. Results: No SNVs reached Bonferroni-corrected significance in any genetic model. Polygenic risk scores (PRS) showed weak predictive ability for bleeding with apixaban. For rivaroxaban, regression indicated that ln Css min/D + 1 index increased with PRS, age, and 6-β-hydroxycortisol/cortisol ratio, but decreased with higher 6-β-hydroxycortisol and coronary heart disease presence. Conclusions: The findings revealed that the residual equilibrium concentration of anticoagulants, including dose-adjusted, cannot alone predict bleeding risk in non-valvular AF patients. No new genetic variants associated with bleeding risk were identified.

P-band radar remote sensing applied during the Airborne Microwave Observatory of Subcanopy and Subsurface (AirMOSS) mission has shown great potential for estimation of root zone soil moisture. When retrieving the soil moisture profile (SMP) from P-band radar, a mathematical function describing the vertical moisture distribution is required. Because only a limited number of observations are available, the number of free parameters of the mathematical model must not exceed the number of observed data. For example, a second order polynomial that contains 3 free parameters was presumed based on in-situ SMP data. The polynomial is currently parameterized based on 3 backscatter observations provided by AirMOSS (i.e. one frequency at three polarizations of HH, VV and HV). In this paper, a more realistic, physically-based SMP model containing 3 free parameters is derived based on a solution to Richards’ equation for unsaturated flow in soils. Evaluation of the new SMP model based on both numerical simulations and measured data revealed that it exhibits greater flexibility for fitting measured and simulated SMPs than the currently applied polynomial. It is also demonstrated that the new SMP model can be reduced to a second order polynomial at the expense of fitting accuracy.

Interest grows in designing silicon-on-insulator slot waveguides to trap optical fields in subwavelength-scale slots and developing their optofluidic devices. However, it is worth noting that the inherent limitations of the waveguide structures may result in high optical losses and short optical paths, which challenge the device performance in optofluidics. Incorporating the planar silicon-based slot waveguide concept into a silica-based hollow-core fiber can provide a perfect solution to realize an efficient optofluidic waveguide. Here we propose a subwavelength-scale liquid-core hybrid fiber (LCHF), where the core is filled with carbon disulfide and surrounded by a silicon ring in a silica background. The waveguide properties and the Stimulated Raman Scattering (SRS) effect in the LCHF are investigated. The fraction of power inside the core of 56.3% allows an improved sensitivity in optical sensing; while the modal Raman gain of 23.60 m-1·W-1 is 2 times larger than that generated around a nano fiber with the interaction between the evanescent optical field and the surrounding Raman media benzene-methanol, which enables a significant low-threshold SRS effect. Besides, this in-fiber structure features compactness, robustness, flexibility, ease of implementation in both trace sample consumption and reasonable liquid filling duration, as well as compatibility with optical fiber systems. The detailed analyses of the properties and utilizations of the LCHF suggest a promising in-fiber optofluidic platform, which provides a novel insight into optofluidic devices, optical sensing, nonlinear optics, etc.

One method of estimating the evaporation rate (ER) is to use a variety of evaporation pans, such as the Class A standard evaporation pan (CASEP) and the Colorado Sanken standard evaporation pan (CSSEP). In this study, the rate of evaporation of CASEP and CSSEP have been investigated and compared with each other. This study was conducted in Semnan, Iran. CSSEP was used as a test pan, which was performed in an open space around the Faculty of Civil Engineering, Semnan University. Evaporation was recorded daily for 123 days. The evaporation of the CASEP pan was obtained from the synoptic station of Semnan, which is located at a distance of 2.39 km from the test site. Meteorological data were also obtained from the synoptic station of Semnan and compared with experimental evaporation data. The results of this study showed that the daily ER from CASEP and CSSEP in the tested time periods were not significantly different. Based on the Klomogorov-Sminrov method, the best statistical distributions for CASEP and CSSEP were calculated as Error and Gamma, respectively. The coefficient of determination (R 2 ) between the two pans was estimated to be about 93%. Also, by examining the ER with other meteorological data, it was observed that the ER has the highest correlation with the average daily air temperature.

Questionnaires for self-report of food-elicited emotions are an established practice in consumer studies. However, most tools are originally developed in English and translated into other languages, which limits their use. The aim of this study was to develop the first Greek emotion lexicon and measurement tool for consumers, using standard methodology and extending it. The lexicon was compiled using linguistic sources and extended using the World Wide Web and a popular social media platform for the collection of authentic language and usage data. Terms were also collected from consumers using questionnaires and a variety of stimuli. Terms collected from consumers only comprise: healthy, distrustful, curious, childish, impressed, tolerant, impatient It was validated by application in various case studies, providing discrimination across and within food categories, and by comparison to the Greek translation of a standard tool in English, the EsSense Profile. The comparison was conducted by measuring emotions elicited by six food categories and demonstrated that it is preferable to use emotion measurement tools developed in the linguistic and cultural context of intended use, as they convey consumers’ emotions naturally and more accurately. This tool can be used as a Check- or Rate- All-That-Apply questionnaire to measure consumer responses to food categories and products. The methodology and validation presented can be applied for the compilation of emotion lexicons in languages less studied than English.

Wide-field (WF) retinal imaging is becoming a standard diagnostic tool for diseases involving the retinal periphery. Technological progress elicited the advent of wide-field optical coherence tomography (WF-OCT) and WF-OCT angiography (WF-OCTA) examinations. This review presents the results of studies that analyzed the implementation of these procedures in clinical practice and refers to them as traditional and ultra-wide-field fluorescein angiography (UWF-FA). The PUBMED search was performed using the terms WF-OCT OR WF-OCTA OR UWF-FA AND the specific clinical entity, including diabetic retinopathy (DR), retinal vein occlusion (RVO), Coats disease, peripheral retinal telangiectasia, peripheral retinal degeneration, lattice degeneration, and posterior vitreous detachment. The analysis only included the studies in which the analyzed field of view for the OCT or OCTA exam was larger than 55 degrees. The evaluation of the extracted studies indicates that WF imaging with OCT and OCTA provides substantial information on retinal disorders involving the retinal periphery. Vascular diseases, such as DR or RVO, can be reliably evaluated using WF-OCTA with results superior to standard-field fluorescein angiography. Nevertheless, UWF-FA provides a larger field of view and still has advantages over WF-OCTA concerning the evaluation of areas of non-perfusion and peripheral neovascularization. Detailed information on the vascular morphology of peripheral changes should be obtained via WF-OCTA, not angiographic examinations. WF-OCT can serve as a valuable tool for the detection and evaluation of vitreoretinal traction, posterior vitreous detachment, and peripheral retinal degeneration, and guide therapeutic decisions on a patient’s eligibility for surgical procedures.

Sparse training (ST) aims to ameliorate deep learning by replacing fully connected artificial neural networks (ANNs) with sparse or ultra-sparse ones, such as brain networks are, therefore it might benefit to borrow brain-inspired learning paradigms from complex network intelligence theory. Here, we launch the ultra-sparse advantage challenge, whose goal is to offer evidence on the extent to which ultra-sparse (around 1% connection retained) topologies can achieve any leaning advantage against fully connected. Epitopological learning is a field of network science and complex network intelligence that studies how to implement learning on complex networks by changing the shape of their connectivity structure (epitopological plasticity). One way to implement Epitopological (epi- means new) Learning is via link prediction: predicting the likelihood of non-observed links to appear in the network. Cannistraci-Hebb learning theory inspired the CH3-L3 network automata rule for link prediction which is effective for general-purpose link prediction. Here, starting from CH3-L3 we propose Epitopological Sparse Meta-deep Learning (ESML) to apply Epitopological Learning to sparse training. In empirical experiments, we find that ESML learns ANNs with ultra-sparse hyperbolic (epi-)topology in which emerges a community layer organization that is meta-deep (meaning that each layer also has an internal depth due to power-law node hierarchy). Furthermore, we discover that ESML can in many cases automatically sparse the neurons during training (arriving even to 30% neurons left in hidden layers), this process of node dynamic removal is called percolation. Starting from this network science evidence, we design Cannistraci-Hebb training (CHT), a 4-step training methodology that puts ESML at its heart. We conduct experiments on 7 datasets and 5 network structures comparing CHT to dynamic sparse training SOTA algorithms and the fully connected counterparts. The results indicate that, with a mere 1% of links retained during training, CHT surpasses fully connected networks on VGG16, GoogLeNet, ResNet50, and ResNet152. This key finding is an evidence for ultra-sparse advantage and signs a milestone in deep learning. CHT acts akin to a gradient-free oracle that adopts CH3-L3-based epitopological learning to guide the placement of new links in the ultra-sparse network topology to facilitate sparse-weight gradient learning, and this in turn reduces the convergence time of ultra-sparse training. Finally, CHT offers the first examples of parsimony dynamic sparse training because, in many datasets, it can retain network performance by percolating and significantly reducing the node network size. Our code is available at: https://github.com/biomedical-cybernetics/Cannistraci-Hebb-training.

Short-range Internet of Things (IoT) sensor nodes operating at 2.4 GHz need to provide ubiquitous wireless sensor networks (WSNs) with energy-efficient, wide-range output power (POUT) and fully integrated on a single chip for wireless body area networks (WBANs) and wireless personal area networks (WPANs) using low-power Bluetooth (BLE) and Zigbee standards. The proposed fully integrated transmitter (TX) utilizes a digitally controllable current-mode class-D (CMCD) power amplifier (PA) with a second harmonic distortion (HD2) suppression to reduce VCO pulling in an integrated system while meeting harmonic limit regulations. The CMCD PA is divided into 7-bit slices that can be reconfigured between differential and single-ended topologies. Duty cycle distortion compensation is performed for HD2 suppression, and an HD2 rejection filter and a modified C-L-C low-pass filter (LPF) reduce HD2 further. Implemented in a 28 nm CMOS process, the TX achieves a wide POUT range of from 12.1 to -31 dBm and provides a maximum efficiency of 39.8% while consuming 41.1 mW at 12.1 dBm POUT. The calibrated HD2 level is -82.2 dBc at 9.93 dBm POUT, resulting in a transmitter figure of merit (TX_FoM) of -97.52 dB. Higher order harmonic levels remain below -41.2 dBm even at 12.1 dBm POUT, meeting regulatory requirements.

Why do stretched rubber bands not hit the hand after ejection? What is the mechanism behind the rubber band ejection dynamics? These questions represent a fascinating scientific problem. Because the size of a rubber band in the circumferential direction is much larger than that in the other two directions of its cross-section, we regard the rubber band as a slender beam and establish a mathematical model of the dynamics of the rubber band stretching and ejection. Furthermore, we obtain the dependence of the dynamic curvature of the rubber band on the arc length and time. We used the finite element software ABAQUS to simulate the dynamic process of a rubber band stretching and ejection. The simulation results and dimensional analysis were performed to examine the effect of the bending elastic rebound velocity. The mathematical model and simulation results revealed that the relationship between the curvature and time at the end of the rubber band ($s =0$) was as follows: $\kappa\sim t^{-{1}/{2}}$. This research has guiding significance for the design of rubber bands as elastic energy storage devices.

Diacylglycerol kinase (DGK) is a lipid kinase that phosphorylates diacylglycerol (DAG) to generate phosphatidic acid (PA). Based on converting one important signaling molecule (DAG) to another (PA), DGK plays an important role in plant responses to abiotic stress including waterlogging stress. However, no studies have been reported on the characterization of the DGK gene family in the waterlogging-tolerant kiwifruit germplasm, Actinidia valvata Dunn. Here, we identified 18 AvDGK genes in the A. valvata genome. The phylogenetic analysis showed that AvDGKs can be classified into three clusters, and members within the same cluster have similar domain distribution, exon-intron structures and conserved motif compositions. Chromosome localization analysis revealed that all the AvDGK genes are located across 18 different chromosomes. There were 29 duplicated gene pairs in kiwifruit and all had undergone purifying selection during evolution. Promoter cis-element analysis revealed that the cis-elements within AvDGK genes are associated with multiple functions, including phytohormone signal transduction, stress response, and plant growth and development. The expression pattern analyses indicated that AvDGK play an important role in the fruit development and plant response to waterlogging stress. AvDGKs gene family in the tetraploid A. valvata genome might promote PA synthesis and subsequent signal transduction both under short-term and long-term waterlogging stress. These results provide information regarding the structural characteristics and potential function of DGK genes within kiwifruit and lay a fundamental basis for further research into breeding for enhancing the kiwifruit’s tolerance to waterlogging stress.

The combined effects of global warming and increasing urban heat islands (UHIs) on air temperature and heat stress in cities are notable physical and mental health implications for citizens. With research having shown the effective role of urban green spaces in decreasing urban heat, this study investigated the cooling effect of a large urban park on thermal comfort outside the park area, from psychological and physiological perspectives. The studied park is located in the center of Madrid and adjacent to UHI. The study was performed by conducting field measurements and a survey with questionnaires. The measurements made on six summer days (with two-week intervals) showed that the park’s cooling effect could decrease the air temperature by 2.4-2.8°C right up to the edge of the heat island (600m), and decrease the physiological equivalent temperature (PET) by about 3.9°C. By decreasing air temperature and PET, this park was also shown to increase the perceived thermal comfort (PTC) of the citizens from the psychological perspective in the defined area of effect. This perceived thermal comfort was found to have a significant inverse relationship with PET (P-value <0.05). The examination of cognitive maps drawn by citizens showed that out of the 145 respondents, 68.3% marked the park as the area that they perceive as having the greatest thermal comfort, and prefer as the place to spend time enjoying thermal comfort, irrespective of its distance from their location.

We present a series of computer-assisted high resolution transmission electron (HRTEM) simulations to determine Moiré patters by induced twisting effects between slabs at rotational angles of 3°, 5°, 8°, and 16°, for molybdenum disulfide, graphene, tungsten disulfide, and tungsten selenide layered materials. In order to investigate the electronic structure, a series of numerical simulations using DFT methods was completed using CASTEP with a generalized gradient approximation to determine both band structure and density of states on honeycomb like new superlattices. Our results indicate metallic transitions when rotation approaches 8° with respect to each other for most of the two-dimensional systems that were analyzed.

In this study, a novel task of printing speed optimization for continuous fiber composites is investigated. Using continuous fibers is an innovative approach to reinforce products made by fused filament fabrication (FFF) additive manufacturing (AM) technology. In the printing process of composites with continuous fibers, the printing speed is critical because of its significant effect on the geometric shape of the samples, especially their corners. During optimization in this research, continuous glass fiber (CGF) and polylactic acid (PLA) filaments were utilized as reinforcing phase and matrix, respectively, and were simultaneously fed into the extrusion-based polymer 3D printer to form PLA/CGF composites. The optimization was carried out by calculating the temperature changes of the deposited rasters in the presence and absence of fibers as a first step and then determining the special relationship between the printing speeds and rasters temperature changes. Finally, the optimal and the maximum printing speed was computed based on a hypothesis, which is proved by the results of high-quality printed composites with different geometric shapes.

Agile methods promise to achieve high productivity and provide high-quality software. Agile software development is the most important approach that has spread through the world of software development over the past decade. Software team productivity measurement is essential in agile teams to increase the performance of software development. Due to the prevalence of agile methodologies and increasing competition of software development companies, software team productivity has become one of the crucial challenges for agile software companies and teams. Awareness of the level of team productivity can help them to achieve better estimation results on the time and cost of the projects. However, to measure software productivity, there is no definitive solution or approach whether in traditional and agile software development teams that lead to the occurrence of many problems in achieving a reliable definition of software productivity. Hence, this study aims to propose a statistical model to assess the team’s productivity in agile teams. A survey was conducted with forty software companies and measured the impact of six factors of the team on productivity in these companies. The results show that team effectiveness factors including inter-team relationship, quality conformance by the team, team vision, team leader, and requirements handled by the team had a significant impact on the team’s productivity. Moreover, the results also state that inter-team relations affect the most on software teams’ productivity. Finally, the model fit test showed that 80% of productivity depends on team effectiveness factors.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

Ultra-wideband wavelength division multiplexed networks enable operators to use more effectively the bandwidth offered by a single fiber pair and thus make significant savings, both in operational and capital expenditures. The main objective of this study is to minimize optical node resources, such as transponders, multiplexers and wavelength selective switches, needed to provide and maintain high quality of network services, in ultra-wideband wavelength division multiplexed networks, at low cost. A model based on integer programming is proposed, which includes a detailed description of optical network nodal resources. The developed optimization tools are used to study the ultra-wideband wavelength division multiplexed network performance when compared with the traditional C-band wavelength division multiplexed networks. The analysis is carried out for realistic networks of different dimensions and traffic demand sets.

The diffusion of molecules in aqueous solutions in the domain of membrane technology is very critical in the efficiency of chemical engineering and purification processes. In this study, the diffusion in high and low concentration regions is simulated with finite difference method (FDM), and then the results of numerical computations are coupled with adaptive network-based fuzzy inference system (ANFIS) and bilayered neural network method (BNNM). Machine learning approach can individually predict diffusion phenomena across the domain based on understanding of the machine instead of the discretization of an ordinary differential equation (ODE). The findings of the machine learning method are in good agreement with those of FDM at different times of the simulation. In addition to numerical computation, the error of the system is computed for different iterations. The results show that by increasing the number of iterations and training datasets, all errors reduce significantly for both training and testing. BNN method is also used to train the prediction process of diffusion for a more accurate comparison. This technique is similar to ANFIS method in terms of prediction capability. According to the findings, ANFIS approach predicts diffusion slightly better than BNN method. In this regard, ANFIS technique produces R>0.99 while BNN method produces R around 0.98. Both machine learning methods are accurate enough to predict diffusion throughout the domain for different time steps. The computational time for both algorithms is less than that of FDM method to predict low and high concentrations in the domain. Besides, based on the results, artificial intelligence (AI) can find the relationship between inputs and outputs and determine which input has the main influence on the output in this study to optimize the process. As such, future studies can be focused on AI and other methods for faster prediction and optimization processes.

Skin cancer is an exquisite disease globally nowadays. Because of the poor contrast and apparent resemblance between skin and lesions, automatic identification of skin cancer is complicated. The rate of human death can be massively reduced if melanoma skin cancer can be detected quickly using dermoscopy images. In this research, an anisotropic diffusion filtering method is used on dermoscopy images to remove multiplicative speckle noise and the fast-bounding box (FBB) method is applied to segment the skin cancer region. Furthermore, the paper consists of two feature extractor parts. One of the two features extractor parts is the hybrid feature extractor (HFE) part and another is the convolutional neural network VGG19 based CNN feature extractor part. The HFE portion combines three feature extraction approaches into a single fused feature vector: Histogram-Oriented Gradient (HOG), Local Binary Pattern (LBP), and Speed Up Robust Feature (SURF). The CNN method also is used to extract additional features from test and training datasets. This two-feature vector is fused to design the classification model. This classifier performs the classification of dermoscopy images whether it is melanoma or non-melanoma skin cancer. The proposed methodology is performed on two ordinary datasets and achieved the accuracy 99.85%, sensitivity 91.65%, and specificity 95.70%, which makes it more successful than previous machine learning algorithms.

The nutrient absorption and utilization efficiency in the roots of seedlings are beneficial for increasing crop yield. Creating marker assisted selection for wheat root traits can assist wheat breeders in choosing robust roots to maximize nutrient uptake. Exploring and identifying the effect of different nitrogen applications on RSA is of great significance for breeding nitrogen efficient wheat varieties. In this study, A total of 243 wheat varieties native to the Yellow and Huai Valley regions of China were utilized for genome-wide association studies (GWAS). Furthermore, a recombinant inbred line (RIL) population of 123 lines derived from the cross between Avocet and Chilero was utilized for linkage examination and confirmation of the hereditary loci distinguished by GWAS. Five RSA traits include the relative number of root tips (RNRT); relative total root length (RTRL); relative total root surface area (RTRS); relative total root volume (RTRV) and relative average root diameter (RARD) where evaluated under two N conditions—normal N (NN) supply and low N (LN)—to characterize the NUE of each accession. GWAS and linkage analysis were performed by integrating data from the wheat 660k single nucleotide polymorphism (SNP) chip and diversity arrays technology (DArT) to identify genetic loci associated with RSA. The results showed that based on the ratio of RSA related traits under two N supply conditions, a total of 598 SNP markers, which are significantly associated with RSA related traits, were detected at 160 genetic loci by GWAS. A total of 10 QTL loci related to RSA were dis-covered and identified by linkage mapping. In which, three significant RSA related Quantitative Trait Locus (QTL) were identified, namely qRtrl-3D, qRnrt-3D, and qRtrl-7D. The study has the potential to enhance the effectiveness of selecting root traits in wheat breeding programs, offering valuable insights into the genetic underpinnings of nitro-gen use efficiency (NUE) in wheat. This could lead to the creation of NUE wheat varieties by implementing focused breeding strategies.

Previous research has indicated that ultra-high pressure (UHP) technology is useful in speeding up the extraction process of cold brew (CB) coffee. However, the impact of different degrees of roasting on UHP CB coffee is still unclear. Therefore, this study aimed to investigate the effects of three different degrees of roasting (light, medium, and dark) on the physicochemical and flavor characteristics of UHP CB coffee. The results of this study showed that most physicochemical characteristics of UHP coffee were similar to those of conventional CB coffee, regardless of the degree of roasting. However, the majority of physicochemical characteristics, non-volatile components, and sensory evaluation significantly increased with an increase in roasting degree. The HS-SPME-GC/MS analysis showed that most volatile components, such as pyrazines, furans (except furfural), esters, pyrrole, pyridine, and most aldehydes, increased from light to dark roasting, and this was significantly evident in CB coffee compared with UHP. The content of volatile components in UHP coffee was significantly (P<0.05) higher than that in CB coffee at the same degree of roasting, especially with dark roasting. The combination of orthogonal partial least squares-discriminant analysis (OPLS-DA) and principal component analysis (PCA) indicated that the distance between coffee samples at different degrees of roasting under CB coffee was greater than that under UHP coffee. However, the distance between these two extraction methods at medium roasting was evidently closer than that at light and dark roasting. Moreover, 15 representative differential compounds, such as were Hazelnut pyrazine, linalool, butane-2,3-dione, 3- methylbutanal found by the calculation of odor-active values (OAVs) indicating the main contributing compounds to odor. Overall, the effect of roasting degrees on UHP coffee was less than that on CB coffee, which was consistent with the results of physicochemical characteristics, volatile components, and sensory evaluation.

A novel determination method using flow-through cartridge purification and ultra-high-performance liquid chromatography coupled to tandem mass spectrometry (UPLC-MS/MS) was developed for the identification and quantification of 30 mycotoxins (aflatoxin B1, B2, G1, G2, sterigmatocysin, T-2 toxin, diacetoxyscirpenol, roquefortine C, methylergonovine, ergocornine, lysergol, enniatin A, enniatin A1, enniatin B, enniatin B1, beauvericin, deoxynivalenol, 3-acetylDeoxynivalenol, 15-acetylDeoxynivalenol, patulin, verruculogen, neosolaniol, gliotoxin, HT-2 toxin, wortmannin, zearalenone, α-zearalenol, β-zearalenol, α-zearalanol, and β-zearalanol) in feedstuffs. Mycotoxins were extracted from sample by 0.1% formic acid aqueous solution/acetonitrile (16/84 v/v), then purified by a Cleanert® MC clean-up column. As a result, the pigments and other matrices were efficient removed from the sample extract solution. The purified eluate was collected, then evaporated and redissolved by 0.1% formic acid aqueous solution/acetonitrile (70:30 v/v) for UPLC-MS/MS detection. A BEH Shield RP18 chromatographic column was employed for separation of 30 mycotoxins in a total of 14 min. Multiple-reaction monitoring (MRM) mode was applied for qualitative and quantitative analysis, and matrix calibration curves obtained with the external-standard method was used for quantitation of target analytes. Under optimized conditions, the linearity range was from 2 to 1000 ng/g, and the limit of quantification of the developed method was from 2 to 50 ng/g. The recoveries of 30 mycotoxins spiked in urine samples were from 72.0% to 118.5%, and the relative standard deviation was below 20%. The method was also well approved by certified reference sample, and applied on the real feedstuff samples testing successfully.

Electroencephalography (EEG) is a brain imaging technique in which electrodes are placed on the scalp. EEG signals are commonly decomposed into frequency bands called delta, theta, alpha, and beta.While these bands have been shown to be useful for characterizing various brain states, their utility as a one-size-fits-all analysis tool remains unclear. We present a two-part data-driven methodology for objectively determining the best EEG bands for a given dataset in this paper. First, a decision tree is used to estimate the optimal frequency band boundaries for reproducing the signal’s power spectrum for a predetermined number of bands. The optimal number of bands is then determined using an Akaike Information Criterion (AIC)-inspired quality score that balances goodness-of-fit with a small band count. Data-driven EEG band discovery may aid in objectively capturing key signal components and uncovering new indices of brain activity.

Abstract: Insecure and portable devices in the smart city’s Internet of Things (IoT) network are increasing at an incredible rate. Various distributed and centralized platforms against cyber-attacks have been implemented in recent years, but these platforms are inefficient due to their constrained levels of storage, high energy consumption, the central point of failure, underutilized resources, high latency, and etc. In addition, the current architecture confronts the problems of scalability, flexibility, complexity, monitoring, managing & collecting of IoT data, and defend against cyber-threats. To address these issues, the author presents distributed and decentralized Blockchain-Software Defined Networking (SDN) based energy-optimized architecture for IoT in smart cities. Thus, SDN continuous observing, controlling, managing IoT devices activities and detect possible attacks in the network; Blockchain provides adequate security & privacy against cyber-attacks, reduces the central point of failure issues; Network Function Virtualization (NFV) are used to saving energy, load balancing, as well as increasing the lifetime of the entire network. Also, we introduce a Cluster Head Selection (CHS) algorithm to reduce the energy consumption in the presented model. Finally, we analyze the performance using various parameters (e.g. throughput, response time, gas consumption, communication overhead) and demonstrating the result that provides higher throughput, lower response time, lower gas consumption than existing works for smart cities.

UHPC is a type of cement-based composite used in new construction and/or rehabilitation of existing buildings to extend service life. It is a novel composite material that can serve as an alternative to concrete construction in hostile climates. Following decades of study and production, a diverse variety of commercial UHPC compositions are now available globally to meet the rising number of applicants and demand for high-quality building materials. Although UHPC offers major benefits over normal concrete, its utilization is restricted due to restrictive design rules and exorbitant costs. As a result, a thorough examination of the durability properties of UHPC is required to give important information for material testing requirements and processes, as well as to broaden its practical uses. This report is aimed at increasing basic understanding of UHPC and supporting more UHPC research and applications.

Optical materials with a tunable localized surface plasmon resonance (LSPR) are of a great interest for applications in photonics and optoelectronics. In the present study we explored the potential of generating the LSPR band with an ultra-broad range of over 1000 nm in gold nanoparticles (NPs) precipitated through the thermal treatment in ZnO-Al2O3-SiO2 glass. Using the optical absorption spectroscopy, we demonstrated that the LSPR band's position and shape can be finely controlled by varying the thermal treatment route. Comprehensive methods including Raman spectroscopy, X-ray diffraction and high-resolution transmission electron microscopy were used to study the glass structure, while computational approaches were used for the theoretical description of the absorption spectra. Obtained results allowed us to suggest a scenario responsible for such abnormal LSPR band broadening which includes possible interparticle plasmonic coupling effect taking place during the liquid-liquid phase separation of the heat-treated glass. The formation of gold NPs with an ultra-broad LSPR band in glasses holds promise for sensitizing rare earth ion luminescence for new photonics devices.

Early diagnosis, prioritization, screening, clustering and tracking of COVID-19 patients, and production of drugs and vaccines are some of the applications that have made it necessary to use a new style of technology to involve, to manage and deal with this epidemic. Strategies backed by artificial intelligence (AI) and the Internet of Things (IoT) have been undeniable to understand how the virus works and try to prevent it from spreading. Accordingly, the main aim of this survey article is to highlight the methods of ML, IoT and the integration of IoT and ML-based techniques in the applications related to COVID-19 from the diagnosis of the disease to the prediction of its outbreak. According to the main findings, IoT provided a prompt and efficient approach of following the disease spread. Most of the studies developed by ML-based techniques for handling COVID-19 based dataset provided performance criteria. The most popular performance criteria, is related to accuracy factor. It can be employed for comparing the ML-based methods with different datasets. According to the results, CNN with SVM classifier, Genetic CNN and pre-trained CNN followed by ResNet, provided highest accuracy values. On the other hand, the lowest accuracy was related to single CNN followed by XGboost and KNN methods.

This paper provides the state of the art of data science in economics. Through a novel taxonomy of applications and methods advances in data science are investigated. The data science advances are investigated in three individual classes of deep learning models, ensemble models, and hybrid models. Application domains include stock market, marketing, E-commerce, corporate banking, and cryptocurrency. Prisma method, a systematic literature review methodology is used to ensure the quality of the survey. The findings revealed that the trends are on advancement of hybrid models as more than 51% of the reviewed articles applied hybrid model. On the other hand, it is found that based on the RMSE accuracy metric, hybrid models had higher prediction accuracy than other algorithms. While it is expected the trends go toward the advancements of deep learning models.

QSO B0218+357 is a blazar located at a cosmological redshift of 0.944. The source is gravitationally lensed by a spiral galaxy located at the redshift of 0.68. Strong gravitational lensing splits the signals emitted by the source into two components separated by 10-12 days, as observed in radio and gamma-ray bands. In July 2014 a GeV flare was observed by Fermi-LAT, triggering follow-up observations with the MAGIC telescopes at energies above 100 GeV. The expected time delay between the components allowed us to plan broad band MWL observations before, during and after the trailing component of the emission. The MAGIC observations at the expected time of arrival of the trailing component resulted in the first detection of QSO B0218+357 in Very-High-Energy (VHE, >100 GeV) gamma rays. It is both the farthest known VHE object and one of only a few Flat Spectrum Radio Quasars detected in this energy range. We report here the observed multiwavelength spectral and temporal properties of the emission during the 2014 flare.

To address the response of small RNAs (sRNAs) biogenesis to drought stress, we identified sRNAs biogenesis genes, including 11 encoding argonauts (AGO), 8 encoding dicer-like proteins (DCL), and 9 encoding RNA-dependent RNA polymerases (RDR) in the peach genome. Notably, the largest numbers of sRNAs biogenesis genes are located to chromosome 1. The PAZ, PIWI, and MID domains were identified in PpAGOs, while the ribonuclease IIIa and IIIb domains were characterized in PpDCLs. The RDRP domain was recognized in PpRDRs. Orthologous similarity and collinearity analyses between Arabidopsis and peach revealed 5, 1, and 2 collinear blocks in AGOs, DCLs, and RDRs, respectively. Moreover, 41, 40, and 42 cis-acting elements were located in the promoters of PpAGOs, PpDCLs, and PpRDRs, respectively, with the majority related to drought stress response. Analysis of RNA sequencing (RNA-seq) data revealed that sRNAs biogenesis genes were involved in drought stress response in different tissues. Furthermore, the expression of candidate genes was verified in two peach cultivars, Beijing 2-7 (BJ2-7) and Sinai (SN), which are drought tolerance and sensitive, respectively. Interestingly, the expression of PpAGO2b, PpDCL2b, PpDCL4, and PpRDR4 genes was induced in ‘BJ2-7’ but inhibited in ‘SN’ under drought stress. Overall, this study provides insight into the roles of sRNA biogenesis genes in response to drought stress in peach.

In this paper thermo-mechanical behavior of 4D printed Polylactic Acid (PLA) was investigated, focusing on its response to varying strain rates and temperatures below the glass transition temperature. Dynamic mechanical analysis and uniaxial tensile tests confirmed PLA's dependency on strain rate, showcasing its sensitivity to external stimuli. Stress-strain curves exhibited typical thermoplastic behavior, with yield stresses varying with strain rates, underscoring PLA's responsiveness to different deformation speeds. Clear strain rate dependence was observed, particularly at quasi-static rates, with temperature and strain rate fluctuations significantly influencing PLA's mechanical properties, including yield stress and deformation behavior. Isothermal compression tests demonstrated predictable stress-strain curves with distinct yield points, while adiabatic tests reveal additional complexities such as heat accumulation leading to further softening. Thermal imaging revealed temperature increase during deformation, highlighting the material's thermo-sensitive nature. These findings provide the basis for future research with the focus on advanced modeling techniques and mitigation strategies for self-heating effects, aiming to enhance PLA-based product reliability and performance in applications with deformations at higher strain rates, while also developing models to simulate shape recovery in 4D printed PLA structures at both cold and hot programming temperatures.

Severe acute respiratory syndrome coronavirus-2 (SARS-CoV-2), a novel evolutionarily divergent RNA virus etiological agent of COVID-19, is responsible for present devastating pandemic respiratory illness. To explore the genomic signatures, we comprehensively analyzed 2,492 complete and/or near-complete genome sequences of SARS-CoV-2 strains reported from across the globe to the GISAID database up to 30 March 2020. Genome-wide annotations revealed 1,407 nucleotide-level mutations at different positions throughout the entire genome of SARS-CoV-2. Moreover, nucleotide deletion analysis found nine deletions throughout the genome, including in polyprotein (n=6), ORF10 (n=1) and 3´-UTR (n=2). Evidence from the systematic gene-level mutational and protein profile analyses revealed a large number of amino acid (aa) substitutions (n=722), making the viral proteins heterogeneous. Notably, residues of receptor-binding domain (RBD) having crucial interactions with angiotensin-converting enzyme 2 (ACE2), and cross-reacting neutralizing antibody were found to be conserved among the analyzed SARS-CoV-2 strains, except for replacement of Lysine with Arginine at 378 position of the cryptic epitope of a Shanghai isolate, hCoV-19/Shanghai/SH0007/2020 (EPI_ISL_416320). Our method of genome annotation is a promising tool for monitoring and tracking the epidemic, the associated genetic variants, and their implications for the development of effective control and prophylaxis strategy.

The development effect of water flooding in ultra-low permeability reservoir was poor due to its poor physical property and high shale content, the experimental study of air flooding which help to complement producing energy was carried out. Based on the Accelerating Rate Calorimeter experimental results, the crude oil of N block in L oilfield can produce low-temperature oxidation reaction, which was the basic condition of air flooding. Three groups of experiment natural cylinder core were designed for oil displacement, water flooding and air flooding were used respectively, and the relationship of differential pressure, oil recovery, injection capacity with injection volume was investigated. It has been showed on the result that the recovery efficiency improved sharply than water flooding, the effect of depressurization and augmented injection was obvious, and the air displacement was validation.

Efficient beam steerable high-gain antennas enable high-speed data rates over long-distance networks, including wireless backhaul, satellite communications (SATCOM), and SATCOM On-the-Move. These characteristics are essential for advancing contemporary wireless communication networks, particularly within 5G and beyond. Various beam-steering solutions have been proposed in the literature, with passive beam-steering mechanisms employing planar metasurfaces emerging as cost-effective, power-efficient, and compact options. These attributes make them well-suited for use in confined spaces, large-scale production and widespread distribution to meet the demands of the mass market. Utilizing a dual-band antenna terminal setup is often advantageous for full duplex communication in wireless systems. Therefore, this article presents a comprehensive review of the dual-band beam steering techniques for enabling full-duplex communication in modern wireless systems, highlighting their design methodologies, scanning mechanisms, physical characteristics, and constraints. Despite the advantages of planar metasurface-based beam steering solutions, literature on dual-band beam steering antennas supporting full duplex communication is limited. This review article identifies research gaps and outlines future directions for developing economically feasible passive dual-band beam-steering solutions for mass deployment.

We investigate the tunneling of quasiparticles through a potential barrier of finite height and width, in a system with a band structure consisting of a quadratic band crossing point (QBCP). We compute the results of the transmission coefficient at various incident angles, and also the conductivity and the Fano factor. We discuss the distinguishing signatures of these transport properties in comparison with other semimetals, as well as electrons in normal metals.

In this research paper, design and development of pyramidal horn antenna for J-band application is reported. It is particularly designed for 17 dB gain and half beam width about 25 degrees at 6.93 GHz. Horn aperture, horn axial length and distance from the throat of the antenna to aperture are the main design constraints which are calculated and used for the antenna design and simulation. Beam width in E-plane and H-plane horn is calculated and it is 19.18 dB and 22.86 dB respectively. The reported antenna design shows good performance for J-band in radiometry, satellite, and radar applications.

The straightness error of guideway is one of the key indicators of ultra-precision machine, which plays an important role in the machining accuracy of work-piece. In order to measure straightness error of long distance ultra-precision guideway accurately, a splicing measurement for straightness error of guideway using high-precision flat mirror and displacement sensor was proposed in this paper, and the data splicing processing algorithm based on coordinate transformation was studied. Then comparative experiments on splicing measurement and direct measurement of straightness error were carried out on a hydrostatic guideway grinder. The maximum difference between the two measurements was about 0.3μm, which was far less than the straightness error of 5.8μm. The experiment demonstrated the correctness of the proposed splicing measurement method and data processing algorithm. To suppress the influence of straightness error on machining accuracy, a straightness error compensation algorithm based on error rotation transformation and vertical axis position correction was proposed, and the grinding experiment of a plane optics with size of 1400mm×500mm was carried out, whose flatness error after grinding was about 2.98μm. The straightness error of the grinding machine had been well suppressed.

Distributed Energy Resources might have a severe influence on Power Line Communications, as they can generate interfering signals and high frequency emissions or supraharmonics that may cause loss of metering and control data. In this paper, the influence of various energy resources on Narrowband Power Line Communications is described and analyzed through several test measurements performed in a real microgrid. Accordingly, the paper describes the effects on smart metering communications through MAC layer analysis. Results show that the commutation frequency of inverters and the presence of battery chargers are remarkable sources of disturbance in low voltage distribution networks. In this sense, the results presented can contribute to efforts towards standardization and normative of emissions at higher frequencies higher, such as CENELEC EN 50160 and IEC/TS 62749.

UHPC is a cement-based composite that is used in new construction and/or renovation of existing structures to increase their service life. It is a unique composite material that may be used as an alternative to concrete in harsh conditions. Following decades of research and development, a wide range of commercial UHPC compositions are now accessible across the world to fulfill the growing number of applications and demand for high-quality construction materials. Although UHPC has significant advantages over conventional concrete, its use is limited because of rigid design restrictions and excessive pricing. As a consequence, a detailed analysis of UHPC's durability qualities is necessary to provide critical information for material testing requirements and methods, as well as to widen its practical applications. The goal of this study is to learn more about UHPC and to encourage more research and use of UHPC.

Social capital creates a synergy that brings many benefits to members of a community. Thus, the main objective of this article was to examine whether social capital can improve a society's food security. If yes, how? To answer these questions, a systematic literature review was conducted using the Prisma approach. The output of this method led to finding 39 related articles. Precise studying these articles illustrated that social capital improves food security through two mechanisms of knowledge sharing and product sharing (i.e., sharing food products). It revealed that social capital through improving the food security pillars (i.e., food availability, food accessibility, food utilization, and food system stability) affects food security. In other words, the interaction among the members of the community results in sharing food products and information among community members, and this facilitates food availability and access to food. There are many shreds of evidence in the literature that sharing food and food product among the community member decreases household food security and provides the healthy nutrition to the vulnerable families and improve the food utilization pillar of food security. In addition, it is disclosed that belonging to the social networks increases the resilience of the community members and decreases the vulnerability of the community that subsequently strengthens the stability of a food system. This study contributes to the common literature on food security and social capital by providing a conceptual model based on the literature. In addition to researchers, policymakers can use the finding of this study to provide solutions to address food insecurity problems.

Major depressive disorder (MDD) is a prevalent mental health condition with substantial social and economic consequences. This study focuses on the interplay between genetic and environmen-tal factors in MDD, with particular emphasis on epigenetic mechanisms such as stochastic epige-netic mutations (SEMs), epigenetic age acceleration, and epigenetic drift. We conducted a meta-analysis of DNA methylation patterns across six datasets (n=1125 MDD cases, 398 controls in whole blood; n=95 MDD cases, 96 controls in brain tissues) from the Gene Expression Omnibus. The analysis did not reveal significant global methylation differences between MDD cases and controls. However, a brain-specific probe (cg25801113) near the SHF gene consistently exhibited hypomethylation, suggesting its potential relevance to MDD. SEMs were assessed, revealing a dis-tinct burden at the gene level in MDD cases, though no significant findings emerged for epigenetic age acceleration, indicating it may not play a central role in MDD. The study also identified rare epivariations in specific genes unique to MDD cases. In blood tissue, 51 genes were associated with these unique epivariations, while 1 gene was highlighted in the brain tissue. These results un-derscore the importance of exploring rare epivariations in understanding the molecular mecha-nisms underlying MDD and offer potential targets for further investigation.

The current emphasis in the advancement of space-based synthetic aperture radar (SAR) is on lightweight payloads under 100kg with resolutions surpassing 1m. This focus is directed towards meeting the launch criteria for multiple satellites on a single rocket and cutting costs. This article discusses the creation and progress of a Ku-band SAR payload for the Taijing-4(03) Satellite, launched on January 23, 2024 accompanied by four other satellites. The SAR payload design was customized to meet the demands of a micro-nano satellite platform, resulting in a lightweight, flat design weighing less than 80kg, seamlessly integrated with the plate-shaped satellite platform. The article also introduces a beam optimization strategy for the phased array SAR antenna, significantly boosting the SAR system’s performance. The SAR payload provides various operating modes like slide-spot, strip, scan 1, scan 2, and others, with a maximum achievable resolution exceeding 1m. Extensive in-orbit testing of the payload produced numerous high-quality SAR images with potential uses in emergency disaster mitigation, safeguarding ecosystems, monitoring forests, managing crops, tracking sea ice, and more.

Silicon photonics is emerging as a competitive platform for electronic-photonic integrated circuits (EPICs) at the 2 µm wavelength band where GeSn photodetectors (PDs) have proven to be efficient PDs. Here, we present a comprehensive theoretical study of GeSn vertical p-i-n homojunction waveguide photodetectors (WGPDs) that have a strain-free and defect-free GeSn active layer for 2-µm Si-based EPICs. The use of a narrow-gap GeSn alloy as the active layer can fully cover entire the 2 µm wavelength band. The waveguide structure allows for decoupling the photon-absorbing path and the carrier-collection path, thereby allowing for simultaneous achievement of high-responsivity and high-bandwidth (BW) operation at the 2-µm wavelength band. We present the theoretical models to calculate the carrier saturation velocities, optical absorption coefficient, responsivity, 3-dB bandwidth, zero-bias resistance, and detectivity, and optimize this device structure to achieve highest performance at the 2-µm wavelength band. The results indicate that the performance of the GeSn WGPD has strong dependence on the Sn composition and geometric parameters. The optimally designed GeSn WGPD with 10% Sn concentration can give responsivity of 1.55 A/W, detectivity of 6.12×1010 cmHz½W-1 at 2 µm wavelength, and ~97 GHz BW. Therefore, this optimally designed GeSn WGPD is a potential candidate for silicon photonic EPICs offering high-speed optical communications.

The unfolded band structure and optical properties of Cu-doped KCl crystals were computed by first principles within the framework of density functional theory, implemented in the ABINIT electronic structure package utilizing pseudopotential approximation and a plane-wave basis set. From a theoretical point of view, Cu substitution into pristine KCl crystals requires calculation by the supercell (SC) method. This procedure shrinks the Brillouin zone, resulting in a folded band structure that is difficult to interpret. To solve this problem and gain insight into the effect of copper ions (Cu+) on electronic properties, the band structure of SC KCl:Cu was unfolded to make a direct comparison with the band structure of the primitive cell (PC) of pristine KCl. To understand the effect of Cu substitution on optical absorption, we calculated the imaginary part of the dielectric function of KCl:Cu through a sum-over-states formalism and broke it down into different band contributions by partially making an iterated cumulative sum (ICS) of selected valence and conduction bands. Consequently, we identified those interband transitions that give rise to the absorption peaks due to the Cu+ ion. These transitions involve valence and conduction bands formed by the Cu-3d and Cu-4s electronic states

We report the detection of live Escherichia coli (E. coli) in liquid samples using a biosensor based on a field effect transistor (FET) biosensor with B/N co-coped graphene oxide (GO) gel (BN-GO) as the transducer material. The FET was functionalized with antibodies to detect E. coli K12 O-antigens in phosphate-buffered saline (PBS). The biosensor detected the presence of planktonic E. coli bacterial cells within a mere 2 minutes. The biosensor exhibited a limit of detection (LOD) of 10 cells per sample, which can be extrapolated to a limit of detection at the level of a single cell per sample and a detection range of at least 10– 108 CFU/mL. The selectivity of the biosensor for E. coli was demonstrated using Bacillus thuringiensis (B. thuringiensis) as a sample contaminant. We also present a comparison of our functionalized BN-GO FET biosensor with established detection methods of E. coli k12 bacteria, as well as with state-of-the-art detection mechanisms.

A single paragraph of about 200 words maximum. For research articles, abstracts should give a Ultra-high performance concrete (UHPC) has gained worldwide popularity because of its notable mechanical response. This research studied the compressive strength, modulus of elasticity, and flexural tensile strength of UHPC. Batches were made with the addition of steel and PVA fibers using a standard procedure defined in the research. The experimental data from the compressive strength test was analyzed in the Statistica 10 software to investigate the fibers' influence on UHPC's mechanical properties. An analysis of the elastic modulus prediction was carried out according to international standards. It was found that the normalized equations for the elastic modulus are not adequate for its estimation. The statistical analysis indicated that the range of fiber quantities analyzed did not significantly affect the compressive strength and the elastic modulus. Regarding the optimized mix, its flexural tensile strength indicates that the fiber content must be higher for UHPC to be suitable for structural use.

New multilayer 3D nanocomposite wear-resistant ion-plasma hard and superhard coatings Avinit [(TiN-AlN)(Mo-Cr-V-Si)]_n have been developed.The introduction of additional alloying elements (Mo, Cr, V, Si) into the Ti-Al-N coating composition, which have a high affinity for nitrogen and are capable of forming strong nitride nanoparticles in the Ti-N and Al-N layers.This makes it possible to obtain hard and superhard hardening coatings.The metallographic and tribological studies carried out indicate the prospects of the developed multicomponent multilayer nano- and microstructured Avinit coatings for increasing wear resistance and reducing friction coefficients.This paper is devoted to the development and implementation of Avinit vacuum plasma technologies for strengthening cutting and forming tools to improve tool performance.Production tests of cutting tools with Avinit's developed multilayer wear-resistant ion-plasma coatings in production conditions at many large machine-building enterprises have shown their high efficiency.In serial production, the wear resistance of tools increases by 3 to 30 times, stamps by 5 to 100 times, and parts rubbing against abrasive materials by 10 to 100 times.Avinit's vacuum plasma technologies have been successfully implemented in production in the aggregate and engine building, transport engineering, and power engineering industries.Positive experience in applying multicomponent coatings has been gained not only when applying hardening coatings to manufactured cutting tools, but also after regrinding to regrindable carbide cutting tools from domestic and foreign manufacturers.

This paper seeks to optimize the mechanical and durability properties of ultra-high performance concrete (UHPC). To meet this objective, concrete specimens were manufactured by using 1,100 kg/m3 of binder, water/binder ratio 0.20, silica sand and last generation of superplasticizer. Silica fume, metakaolin and two types of nano silica were used for improving the performances of the concrete. Additional mixtures included 13mm long OL steel fibers. Compressive strength, electrical resistivity, mercury intrusion porosimetry tests and differential and thermogravimetric thermal analysis were carried out. The binary combination of nano silica and metakaolin, and the ternary combination of nano silica with metakaolin and silica fume, led to the best performances of the UHPC, both mechanical and durable performances.

With superior optical properties, high flexibility in engineering its material properties, and strong capability for large-scale on-chip integration, graphene oxide (GO) is an attractive solution for on-chip integration of two-dimensional (2D) materials to implement functional integrated photonic devices capable of new features. Over the past decade, integrated GO photonics, representing an innovative merging of integrated photonic devices and thin GO films, has experienced significant development, leading to a surge in many applications covering almost every field of optical sciences. This paper reviews the recent advances in this emerging field, providing an overview of the optical properties of GO as well as methods for the on-chip integration of GO. The main achievements made in GO hybrid integrated photonic devices for diverse applications are summarized. The open challenges as well as the potential for future improvement are also discussed.

This article presents a wide-band antenna designed for the Cube Satellite (CubeSat). Based on a quadrifilar structure, the antenna provides circular polarization radiation, which is suitable for satellite communication. Moreover, the antenna is designed and fabricated using two 1.6 mm thickness FR4-Epoxy boards that connect together by the metal pins. In order to improve the robustness, a ceramic spacer is placed in the centerboard, and four screws at the corners are added to fix the antenna with the CubeSat structure. These additional parts reduce antenna damage caused by vibrations in the launch vehicle lift-off stage. The proposal has a dimension of 77mm x 77mm x 10mm and covers the LoRa frequency bands of 868 MHz, 915 MHz, and 923 MHz. According to the measurements in an anechoic chamber, antenna gains are obtained with the values of 2.3 dBiC and 1.1 dBiC for the 870 MHz and 920 MHz, respectively. Finally, the antenna is integrated into a 3U CubeSat that was launched by a Soyuz launch vehicle. The terrestrial-to-space communication link was measured, and the antenna performance was confirmed in the real-life scenario.

Three cases of Day-Night Band (DNB) observations of the Visible Infrared Imaging Radiometer Suite (VIIRS) onboard the Suomi National Polar-orbiting Partnership (SNPP) are explored for applications to assess the ocean environment and monitor ocean dynamics. An approach to use the DNB radiance ratio was developed in order to better continuously assess the ocean diurnal and short-term environmental changes with VIIRS DNB observations. In the La Plata River Estuary, the sediment fronts showed 20–25 km diurnal inshore-offshore movements on March 13, 2017. In the waters off the Argentina coast in the South Atlantic, VIIRS DNB measurements provided continuous observations and monitoring of the algae bloom development and migration between 24–26 March 2016. This algae bloom generally kept the same spatial patterns, but moved nearly 20 km eastward in the three-day period. In the Yangtze River Estuary and Hangzhou Bay region in China’s east coast, VIIRS DNB observations also revealed the complicated coastal dynamic changes between 12–14 April 2017. Even though there are still some challenges and limitations for monitoring the ocean environment with VIIRS DNB observations, this study shows that satellite DNB observations can provide additional data sources for ocean observations, especially observations during the nighttime.

In this work, backscattering signatures of snow-covered lake ice and sea ice from X- and Ku-band synthetic aperture radar (SAR) data are investigated. The SAR data were acquired with the ESA airborne SnowSAR sensor in winter 2012 over Lake Orajärvi in northern Finland and over landfast ice in the Bay of Bothnia of the Baltic Sea. Co-incident with the SnowSAR acquisitions in-situ snow and ice data were measured. In addition, time series of TerraSAR-X images and ice mass balance buoy data were acquired for the Lake Orajärvi in 2011-12. The main objective of our study was to investigate relationships between SAR backscattering signatures and snow depth over lake and sea ice, with the ultimate objective of assessing the feasibility of retrieval of snow characteristics using X- and Ku-band dual-polarisation (VV and VH) SAR over freshwater or sea ice. This study constitutes the first comprehensive survey of snow backscattering signatures at these two combined frequencies over both lake and sea ice. For lake ice, we show that X-band VH-polarized backscattering coefficient (σo) and the Ku-band VV/VH-ratio exhibited the highest sensitivity to the snow depth. For sea ice, the highest sensitivity to the snow depth was found from the Ku-band VV-polarised σo and the Ku-band VV/VH-ratio. However, the observed relations were relatively weak, indicating that at least for the prevailing snow conditions, obtaining reliable estimates of snow depth over lake and sea ice would be challenging using only X- and Ku-band backscattering information.

Thin supported inorganic mesoporous membranes are used for removal of salts, small molecules (PFAS, dyes, polyanions) and particulate species (oil droplets) from aqueous sources with high flux and selectivity. Nano-filtration membranes can reject simple salts with 80-100% selectivity through a space charge mechanism. Rejection by size selectivity can be near 100% since the membranes can have a very narrow size distribution. Mesoporous membranes have received par-ticular interest due to their (potential) stability at operational conditions and defouling operations. More recently membranes with extreme stability became interesting with the advent of in-situ fouling mitigation by means of ultrasound, emitted from within the membrane structure. For this reason we explored the stability of available and new membranes with accelerated lifetime tests in aqueous solutions at various temperatures and pH values. Of the available ceria, titania, mag-netite membranes none were actually stable at all test conditions. In earlier work, it was already established that meso-porous alumina membranes have very poor stability. A new nano-filtration membrane was made of cubic zirconia membranes that exhibited a near perfect stability. A new ultra-filtration membrane was made of amorphous silica that was fully stable in ultrapure water at 80°C. This work provides details of membrane synthesis, stability characterization and actual sta-bility data.

In this work, we present a transceiver front-end in SiGe BiCMOS technology that can provide an ultra-wide bandwidth of 100 GHz at millimeter-wave frequencies. The front-end employs a novel configuration for low-loss distribution of broadband generated pulses as well as coherent spatial combining of received pulses. This leads to the realization of a fully integrated ultra-high-resolution imaging chip for biomedical applications. We realized an ultra-wide imaging bandwidth of 100 GHz by the integration of two adjacent, disjointed frequency sub-bands of 10–50 GHz and 50–110 GHz respectively. The transceiver front-end is capable of both transmit (TX) and receive (RX) operations. This is a key building-block for a scalable system in which a unit cell is repeated in the X and Y directions resulting in less power and area consumption. The imaging elements were designed and fabricated in Global Foundry 130-nm SiGe 8XP BiCMOS process technology.

Ultrafast laser 3D lithography based on non-linear light-matter interactions, widely known as multi-photon lithography (MPL), offers unrivaled precision rapid prototyping and flexible additive manufacturing options. 3D printing equipment based on MPL are already commercially available, yet there is still no comprehensive understanding of factors determining spatial resolution, accuracy, fabrication throughput, repeatability, and standardized metrology methods for the accurate characterization of the produced 3D objects and their functionalities. The photoexcitation mechanisms, spatial-control or photo-modified volumes, and the variety of processable materials are topics actively investigated. The complexity of the research field is underlined by limited understanding and fragmented knowledge of light-excitation and material response. Research to date has only provided case-specific findings on photoexcitation, chemical modification, and material characterization of the experimental data. In this review, we aim to provide a consistent and comprehensive summary of the existing literature on photopolymerization mechanisms under highly confined spatial and temporal conditions, where, besides the excitation and cross-linking, parameters such as diffusion, temperature accumulation, and the finite amount of monomer molecules start to become of critical importance. Key parameters such as, photoexcitation, polymerization kinetics, and the properties of the additively manufactured materials at the nanoscale in 3D are examined, whereas, the perspectives for future research and as well as emerging applications are outlined.

Micro-plasma is generated in ultra-high-pure hydrogen gas filled inside a cell at a pressure of (1.08 ± 0.033) × 10⁵ Pa (810 ± 25 Torr) by using a Q-switched Nd:YAG laser device operated at 1064 nm wavelength and 14 ns pulse duration. Micro-plasma emission spectra of the hydrogen Balmer alpha line, H_α, are recorded with a Czerny-Turner type spectrometer and an intensified charge-coupled device. The spectra are calibrated for wavelength and corrected for detector sensitivity. During the first few tens of nanoseconds after initiating optical breakdown, significantly Stark-broadened and Stark-shifted H_α lines mark the well-above hypersonic outward expansion. The vertical diameters of the spectrally resolved plasma images are measured for time delays of 10 ns to 35 ns to determine expansion speeds of the order of 100 km/s to 10 km/s. For time delays of the order of 0.5 µs to 1 µs, the expansion decreases to the speed of sound of 1.3 km/s in the near ambient temperature and pressure hydrogen gas.

Through the use of machine learning algorithms like the Support Vector Machine, it has been show that burn extent can be accurately mapped from hyperspatial drone imagery in both grasslands and forests. Despite these successes, hyperspatial imagery must be acquired via drones, requiring large amounts of time and resources to capture areas much smaller than the large catastrophic fires which result in the majority of the lands burned each year by wildland fires. To overcome this difficulty, high spatial resolution satellite imagery from Worldview2 can be substituted for hyperspatial drone imagery, allowing for larger regions of images to be acquired more easily and efficiently. Additionally, Worldview2 trades spatial resolution for spectral resolution and extent, capturing images in 8 multispectral bands as opposed to 3 band imagery in the visible spectra. This research examines the utility of each of the 8 bands observed in Worldview2 imagery using an Iterative Dichotomiser 3 decision tree, then uses these bands to map burn extent and biomass consumption. Several classifications of burn extent and biomass consumption are produced and compared based on the bands used as inputs. The results show that using Worldview2 imagery to map burn extent and biomass consumption results in highly accurate maps, with slight improvements when additional bands are added.

During the night between 9 and 10 September 2017, multiple flash floods associated to a heavy-precipitation event affected the town of Livorno, located in Tuscany, Italy. Accumulated precipitation exceeding 200 mm in two hours, associated with a return period higher than 200 years, caused all the largest streams of the Livorno municipality to flood several areas of the town. We used the limited-area Weather Research and Forecasting (WRF) model, in a convection-permitting setup, to reconstruct the extreme event leading to the flash floods. We evaluated possible forecasting improvements emerging from the assimilation of local ground stations and X- and S-band radar data into the WRF, using the configuration operational at the meteorological center of Tuscany region (LaMMA) at the time of the event. Simulations were verified against weather station observations, through an innovative method aimed at disentangling the positioning and intensity errors of precipitation forecasts. By providing more accurate descriptions of the low-level flow and a better assessment of the atmospheric water vapour, the results demonstrate that assimilating radar data improved the quantitative precipitation forecasts.

The availability of high quality surface observations of precipitation and volume observations by polarimetric operational radars make it possible to constrain, evaluate and validate numerical models with a wide variety of microphysical schemes. In this article, a novel particle-based Monte-Carlo microphysical model (called “McSnow”) is used to simulate the outer rain bands of Hurricane Dorian which traversed the densely instrumented precipitation research facility operated by NASA at Wallops Island, Virginia. The rain bands showed steady stratiform vertical profiles with radar signature of dendritic growth layers near −15 °C and peak reflectivity in the bright band of 55 dBZ along with polarimetric signatures of wet snow with sizes inferred to exceed 15 mm. A 2D-video disdrometer measured frequent occurrences of large drops &gt;5 mm and combined with an optical array probe the drop size distribution was well-documented in spite of uncertainty for drops &lt;0.5 mm due to high wind gusts and turbulence. The 1D McSnow control run and four numerical “experiments” were conducted and compared with observations. One of the main findings is that even at the moderate rain rate of 10 mm/h collisional breakup is essential for the shape of the drop size distribution.

Ocean surface currents and winds are tightly coupled essential climate variables, and, given their short time scales, observing them at the same time and resolution is of great interest. DopplerScatt is an airborne Ka-band scatterometer that has been developed under NASA's Instrument Incubator Program (IIP) to provide a proof of concept of the feasability of measuring these variables using pencil-beam scanning Doppler scatterometry. In the first half of this paper, we present the Doppler scatterometer measurement and processing principles, paying particular attention to deriving a complete measurement error budget. Although Doppler radars have been used for the estimation of surface currents, pencil-beam Doppler Scatterometry offers challenges and opportunities that require separate treatment. The calibration of the Doppler measurement to remove platform and instrument biases has been a traditional challenge for Doppler systems, and we introduce several new techniques to mitigate these errors when conical scanning is used. The use of Ka-band for airborne Doppler scatterometry measurements is also new, and, in the second half of the paper, we examine the phenomenology of the mapping from radar cross section and radial velocity measurements to winds and surface currents. To this end, we present new Ka-band Geophysical Model Functions (GMF's) for winds and surface currents obtained from multiple airborne campaigns. We find that the wind Ka-band GMF exhibits similar dependence to wind speed as that for Ku-band scatterometers, such as QuikSCAT, albeit with much greater upwind-crosswind modulation. The surface current GMF at Ka-band is significantly different from that at C-band, and, above 4.5 m/s has a weak dependence on wind speed, although still dependent on wind direction. We examine the effects of Bragg-wave modulation by long waves through a Modululation Transfer Function (MTF), and show that the observed surface current dependence on winds is consistent with past Ka-band MTF observations. Finally, we provide a preliminary validation of our geophysical retrievals, which will be expanded in subsequent publications. Our results indicate that Ka-band Doppler scatterometry could be a feasible method for wide-swath simultaneous measurements of winds and currents from space.

The reported study was devoted to the investigation of viscoelastic behavior for solid and porous ultra-high-molecular-weight polyethylene (UHMWPE) under compression. The obtained experimental stress curves were interpreted using a two-term Prony series to represent the superposition of two coexisting activation processes corresponding to long molecular (~160 s) and short structural (~20 s) time scales, respectively, leading to good statistical correlation with the observations. In the case of porous polymer, the internal strain redistribution during relaxation was quantified using Digital Image Correlation (DIC) analysis. The strongly inhomogeneous deformation of the porous polymer was found not to affect the relaxation times. In order to generalize the results to three dimensions, X-ray tomography was used to examine the porous structure at the macro- and micro-scale levels. DIC analysis revealed positive correlation between the applied force and relative density. The apparent stiffness variation for UHMWPE foams with mixed open and closed cells was described using a newly proposed three-term expression. Furthermore, the in situ tensile loading and X-ray scattering study was applied for isotropic solid UHMWPE specimens to investigate their parameters of internal structure during orientation and stress relaxation process at another mode.

Fiber distributed optical fiber acoustic sensor (DAS) is generally used in distributed long-distance acoustic/vibration measurement. We found that DAS with excellent performance of low self-noise and anti-fading in combination with the plastic structure in daily life as an acoustic transducer can achieve high-sensitivity acoustic measurement at a single point rather than designing a state-of-the-art acoustic transducer or using special enhanced scattering fiber. The simple acoustic transducer we proposed for DAS can reach the sensitivity level of -106.5dB re. 1rad/μPa at a sensing range of 5.1 km, which can meet many demands on the industrial site.

Sorghum (Sorghum bicolor L.) ranks fifth as the most crucial cereal crop globally, yet its seed morphology remains relatively unexplored. This study investigated seed morphology in sorghum based on 115 mini core and 130 Senegalese germplasms. Eight seed morphology traits encompassing size, shape, and color parameters were assessed. Statistical analyses explored potential associations between these traits and resistance to three major sorghum diseases: anthracnose, head smut, and downy mildew. Furthermore, genome-wide association studies (GWAS) were conducted using phenotypic data from over 24,000 seeds and over 290,000 publicly available single nucleotide polymorphisms (SNPs) through the Genome Association and Prediction Integrated Tool (GAPIT) R package. Significant SNPs associated with various seed morphology traits were identified and mapped onto the reference sorghum genome to identify novel candidate defense genes.

We report a novel dual-band barrier infrared detector (DBIRD) design using type-II superlattices (T2SLs). The DBIRD structure consists of back-to-back barrier diodes: a "blue channel" (BC) diode which has an nBp architecture, an n-type layer of larger bandgap for absorbing blue band infrared/barrier/p-type layer, and a "red channel" (RC) diode which has an pBn architecture, a p-type layer of smaller bandgap for absorbing red band infrared/barrier/n-type layer. Each has a unipolar barrier using a T2SL lattice matched to a GaSb substrate to impede the flow of majority carriers from the absorbing layer. Each channel in the DBIRD can be independently accessed with a low bias voltage, as is preferable for high-speed thermal imaging. Device modeling of DBIRDs and simulation results of the current-voltage characteristics under dark and illuminated conditions are also presented. They predict that dual-band operation of the DBIRD will produce low dark currents and 27-33% quantum efficiencies for the in-band photons in the BC with λc=5.58 μm, and a nearly-constant 33% in the RC with λc=8.05 μm. The spectral quantum efficiency of the BC for 500 K blackbody radiation is approximately 20% over the range of λ=3 − 4.2 μm, while that of the RC has a peak of 42% at 5.7 μm. The DBIRD may provide improved high-speed dual-band imaging in comparison with NBn dual-band detectors.