The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of >1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.

Background: clubfoot is a common congenital deformity. The Ponseti technique, involving early corrective manipulations followed by the application of long leg casts and Achilles tenotomy, is widely accepted as the preferred treatment. Rapid healing of the tendon after surgery has been documented, but the aspect regarding tendon structure and properties is not known. Three cases of Achilles tendon rupture in adolescent previously treated for clubfoot have been described in the literature. Since rupture is a rare event in this age group a possible correlation with previous surgery has been hypothesized. The primary aim of the study was to compare the ultrasound findings of the Achilles tendon, in patients treated for clubfoot, between patients treated with casting alone and the ones who underwent surgery (percutaneous tenotomy or Z-plasty lengthening). Methods: 22 asymptomatic patients, (34 feet) median age 12 years, previously treated for clubfoot, were recruited for this study; the patients underwent an Achilles tendon ultrasound examination during a follow-up outpatient visit. Results: a greater thickness and structural alterations with presence of hypoechoic areas of the operated tendons compared to those treated with plaster alone were observed (p value: 0.0498 and

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

A portable laser photoacoustic sensor based on a Field-Programmable Gate Array (FPGA) is reported for methane detection. A tunable DFB diode laser in the 1654 nm wavelength range is used as an excitation source. The photoacoustic signal processing was implemented by a FPGA device. A small resonant photoacoustic cell is designed. The minimum detection limit (1σ) of 10 ppm for methane (CH₄) is demonstrated.

This paper presents a study to accurately evaluate defects in reinforced concrete decks using ultrasonic pulse-echo signals. Two validation specimens were designed and tested where reinforced concrete deck slab specimens included planned voids and defects. A commercial Ultrasonic Pulse-Echo (UPE) device obtains 2-D images of the void/defect locations of the reinforced concrete deck. The UPE is based on the ultrasonic shear-wave test method using dry-point-contact transmitting and receiving transducers and employing a synthetic aperture focusing technique. The authors analyzed the recorded UPE A-scan data to enhance the accuracy of estimating the defects' locations using the synthetic aperture focusing technique imaging method. The analysis benefitted from an advanced denoising approach and defect echo peak extraction based on empirical modal decomposition, Hurst exponent characterization, and Hilbert envelope estimation. While output from conventional UPC devices can only provide qualitative results, the new method provides quantitative information on the anomalies inside the reinforced concrete deck. The developed approach accurately assists with assessing the location and depth of the voids/defects in the reinforced concrete deck slabs.

Plastic contamination of small dimensions (

This study was designed for the first time to improve phenolic yield and antioxidant activity of ultrasonic-assisted extraction from Acer truncatum leaves (ATL) using response surface methodology, and phenolic composition in ATL extracted under the optimized condition were characterized by UPLC-QTOF-MS/MS. Solvent and extraction time were selected based on preliminary experiments, and a four-factors-three-levels central composite design was conducted to optimize solvent concentration (X₁), material-to-liquid ratio (X₂), ultrasonic temperature (X₃) and power (X₄) for an optimal total phenol yield (Y₁) and DPPH• antioxidant activity (Y₂). The results showed that the optimal combination was ethanol: water (v:v) 66.21%, material-to-liquid ratio 1:15.31 g/mL, ultrasonic temperature 60 °C, power 267.30 W, and time 30 min with three extractions, giving a maximal total phenol yield of 7593.62 mg gallic acid equivalent /100 g d.w. and a maximal DPPH• antioxidant activity of 74241.61 μmol Trolox equivalent/100 g d.w.. Furthermore, 22 phenolics were first identified in ATL extract obtained under the optimized conditions, indicating that gallates, gallotannins, quercetin, myricetin and chlorogenic acid derivatives were the main phenolic composition in ATL. What’s more, a gallotannins pathway existing in ATL from gallic acid to penta-O-galloyl-glucoside was interpreted. All these results provided practical information aiming at full utilization of phenolics in ATL, together with fundamental knowledge for further research.

In this project, four of fibers Bragg gratings were fabricated by injecting different volumes of liquids (star line Glass Mechanix optical adhesive material, olive oil diluted with ethanol) into the hollow core fiber. The amplitude splitting interferometric technique with a high resolution specially designed translation stage was used for the fabrication process. The fabrication was done using ultraviolet laser operated at wavelength 405nm. The fabricated Bragg length of the four fibers is equal to 3.8 cm. The results presented fiber Bragg grating (FBG) with successful fabrication at 653.3 nm Bragg reflected wavelength.

Ultrasonic feedback energy is affected by the variety, planting and growth state of crops, it is difficult to fine application in precision agriculture systems. To this end, an ultrasonic sensor was mounted in a spray boom height detection system. Winter wheat was used as the test object to obtain feedback energy values for the spray boom height from the top of the wheat in the field during six critical growth stages: the standing stage, jointing stage, booting stage, heading stage, filling stage and maturity stage. The relationship between the actual value of the height from the spray boom to the top of wheat (Habw) and the detected value of the height from the spray boom to the top of wheat (Hdbw) was analyzed. A spray boom height detection model based on the ultrasonic sensor during the full growth cycle of wheat was determined. Field validation tests showed that the applicability of the spray boom height detection distance (Dd) of the spray boom height detection model proposed in the present study was 450 mm~950 mm. Within the applicable Dd range, the detection error of the detection model was ≤5 cm during the full growth cycle. This study provides an ultrasonic detection model construction method, which improves the reliability and accuracy of ultrasonic boom height detection for different wheat growth stages.

This paper investigates an Energy Neutral System using Micro Energy Harvesters for a Health Monitoring Wireless Sensor Node (HM-WSN). We have implemented HM-WSN consisting of a solar cell energy harvester, a Power Management Unit (PMU) and the ucontroller, sensor and transmitter acting as load. A battery extender and a switching logic circuit for sensor node is designed to evaluate the efficiency of the proposed system. The HM-WSN senses body temperature with improvement in lifetime of coincell. The HM-WSN is built using commercially available off the shelf (COTS components and consumes 47.2uW for data being updated every 134s. It can be operated for approximately 1.32 years only on a coincell. Furthermore, the HM-WSN can be operated with solar energy at 200lux, achieving 96.36 years with a combination of a coincell with an additional capacitor of 2.2mF. It attains 4.07 years to 16.87 years lifetime with the load capacitor varying from 1mF to 1.5mF at 350lux lighting condition. With the same ambient condition and a 2mF load capacitor, HM-WSN attains complete energy autonomy.

With the integrated development of the Internet, wireless sensor technology, cloud computing, and mobile Internet, there has been a lot of attention given to research about and applications of the Internet of Things. A Wireless Sensor Network (WSN) is one of the important information technologies in the Internet of Things; it integrates multi-technology to detect and gather information in a network environment by mutual cooperation, using a variety of methods to process and analyze data, implement awareness, and perform tests. This paper mainly researches the localization algorithm of sensor nodes in a wireless sensor network. Firstly, a multi-granularity region partition is proposed to divide the location region. In the range-based method, the RSSI (Received Signal Strength indicator, RSSI) is used to estimate distance. The optimal RSSI value is computed by the Gaussian fitting method. Furthermore, a Voronoi diagram is characterized by the use of dividing region. Rach anchor node is regarded as the center of each region; the whole position region is divided into several regions and the sub-region of neighboring nodes is combined into triangles while the unknown node is locked in the ultimate area. Secondly, the multi-granularity regional division and Lagrange multiplier method are used to calculate the final coordinates. Because nodes are influenced by many factors in the practical application, two kinds of positioning methods are designed: the unknown node is in the positioning unit or not. When the unknown node is on the side of the positioning unit, we use the method of vector similarity. Moreover, we use the centroid algorithm to calculate the ultimate coordinates of unknown node. When the unknown node is not on the side of the positioning unit, we establish a Lagrange equation containing the constraint condition to calculate the first coordinates. Furthermore, we use the Taylor expansion formula to correct the coordinates of the unknown node. In addition, this localization method has been validated by establishing the real environment.

The existence of low-cost and accurate tools that can equip the First Responders (FRs) to detect trapped victims and provide insights about their health condition in the aftermath of a disaster, is imperative. To address the problem of detecting trapped victims behind walls or debris, we have developed a tool that exploits an Ultra-Wide Band (UWB) radar sensor for data collection and Machine Learning (ML) algorithms for data analysis. To evaluate the efficacy of our approach, we collected data from nine humans, both in standing and lying down positions. Next, we applied various ML algorithms to the collected dataset for two discrete sub-tasks that are of interest from an FR’s perspective. The first task is the detection of the victim’s presence, where the algorithms attained more than 95% accuracy and F1-Score. The second task is the estimation of the distance between the radar sensor and the victim, where the tool showed an average error of less than 40 cm.

Underwater Sensor Networks (UWSNs) can enable a broad range of applications such as resource monitoring, disaster prevention, and navigation-assisted. It is especially relevant for sensor nodes location in UWSNs. Global Positioning System (GPS) is not suitable for using in UWSNs because of the underwater propagation problems. Hence some localization algorithms based on the precise time synchronization between sensor nodes have been proposed which are not feasible for UWSNs. In this paper, we propose a localization algorithm called Two-Phase Time Synchronization-Free Localization Algorithm (TP-TSFLA). TP-TSFLA contains two phases, namely, range-based estimation phase and range-free evaluation phase. In the first phase, we address a time synchronization-free localization scheme base on the Particle Swarm Optimization (PSO) algorithm to decrease the localization error. In the second phase, we propose a Circle-based Range-Free Localization Algorithm (CRFLA) to locate the unlocalized sensor nodes which cannot obtain the location information through the first phase. In the second phase, sensor nodes which are localized in the first phase act as the new anchor nodes to help realize localization. Hence in this algorithm, we use a small number of mobile beacons to help achieve location without any other anchor nodes. Besides, to improve the precision of the range-free method, an extension of CRFLA by designing a coordinate adjustment scheme is updated. The simulation results show that TP-TSFLA can achieve a relative high localization ratio without time synchronization.

In this paper, a method is developed for presenting a novel virtual torque sensor based on precise model and position measurements avoids the need of traditional strain gauges and amplifiers. More specifically, the harmonic drive compliance model and the Gaussian process regression (GPR) technique are used together to achieve virtual torque sensor measurement. While the harmonic drive compliance model provides the analytic part, the Gaussian process regression method is used to reconstruct the unmolded part based on motor-side and link-side joint angles as well as motor current. After an automatic offline calibration, the method allows for a lean online implementation. The virtual torque sensor measurement is compared with measurements of a commercial torque sensor, and the results have attested the effectiveness of the proposed method.

The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

Human Activity Recognition (HAR) technology enables continuous behavior monitoring, particularly valuable in healthcare. This study investigates the viability of using an ear-worn motion sensor for classifying daily activities, including lying, sitting/standing, walking, ascending stairs, descending stairs, and running. Fifty healthy participants (between 20 and 47 years old) engaged in these activities while under monitoring. Various machine learning algorithms, ranging from interpretable shallow models to state-of-the-art deep learning approaches designed for HAR, were employed for classification. Results demonstrate the ear sensor's efficacy, with deep learning models achieving 98% accuracy rate of classification. The obtained classification models are agnostic regarding which ear the sensor is worn and robust against moderate variations in sensor orientation (e.g., due to differences in auricle anatomy), meaning no initial calibration of the sensor orientation is required. The study underscores the ear's efficacy as a suitable site for monitoring human daily activity and suggests its potential for combining HAR with in-ear vital signs monitoring. This approach offers a practical method for comprehensive health monitoring by integrating sensors in a single anatomical location. This integration facilitates individualized health assessments, with potential applications in tele-monitoring, personalized health insights, and optimizing athletic training regimes.

We report the relative humidity (R.H.) sensing response of a resistive sensor, employing sensing layers based on a ternary nanohybrid comprising holey carbon nanohorns (CNHox), potassium chloride (KCl), and polyvinylpyrrolidone (PVP) at mass ratios 7/1/2, 6.5/1.5/2, and 6/2/2 (w/w/w/w). The sensing structure comprises a silicon substrate, a SiO2 layer, and interdigitated transducer (IDT) electrodes. The sensing film is deposited on the sensing structure via the drop-casting method. The sensing layers' morphology and composition are investigated through Scanning Electron Microscopy (S.E.M.) and RAMAN spectroscopy. The ternary hybrid-based thin film resistance increases when the sensors are exposed to R.H., ranging from 0% to 100%. The manufactured devices show a room temperature response comparable to a commercial capacitive R.H. sensor and are characterized by excellent linearity, rapid response time, and good sensitivity. The presented sensors exhibit superior performance in terms of sensitivity compared to other similarly manufactured and tested sensors that employ a CNHox-based sensing layer. We explain the sensing role of each constituent of the ternary hybrid nanocomposites based on their chemical and physical properties, electronic properties, and affinity for water molecules. Different alternative sensing mechanisms are considered and discussed, such as the decreasing number of holes in the holey CNHox at the interaction with water molecules, proton conduction, and PVP swelling.

In this paper, a continuous power management for a decentralized DC microgrid (DCMG) is proposed to achieve voltage regulation and power balance even under system uncertainty and voltage sensor failure. The DCMG system achieves a continuous power management through only the primary controller to reduce the computational burden of each power agent. To enhance the reliability and resilience of the DCMG system under voltage sensor failure, a DC bus voltage (DCV) sensor fault detection algorithm is proposed. In this algorithm, the DCV sensor failure is detected by comparing the measured DCV with the estimated DCV. When the power agent identifies the DCV sensor failure, it changes the operation properly according to the proposed control mode decision algorithm to maintain the stability of the DCMG system. When uncertain conditions such as the power variation of the distributed generations, sudden grid disconnection, DCV sensor failure, electricity price change, and critical battery status occur, the DCMG system is changed to transitional operation modes. These transitional operation modes are employed to transmit the power agent information to other agents without digital communication links (DCLs) and to accomplish power sharing even under such uncertain conditions. In the transitional operation modes of the DCMG system, the DCV levels are temporarily shifted to an appropriate level, enabling each power agent to detect the uncertainty conditions, and subsequently to determine its operation modes based on the DCV levels. Simulation and experimental results under different test conditions confirm the reliability and effectiveness of the proposed control scheme.

An easy to implement and cost-effective Fiber Bragg Grating (FBG) sensor interrogation technique based on a ring Erbium-Doped Fiber Laser (EDFL) topology is proposed and experimentally assessed. The FBG sensor is part of the EDFL cavity and must have a central wavelength located within the linear region of the EDF’s amplified spontaneous emission (ASE) spectrum which occurs between 1530 and 1540nm. In this manner, the wavelength-encoded response of the FBG under strain is converted to a linear variation of the laser output power, removing the need for spectrum analysis as well as any limitations from the use of external edge-filtering components. In addition, the laser linewidth is significantly reduced with respect to the FBG bandwidth thus improving the resolution of the system, whereas its sensitivity can be controlled through the pumping power. The performance of the system has been characterized by modeling and experiments for EDF's with different lengths, doping concentrations and pumping power levels. The influence of mode-hopping in the laser cavity on the resolution and accuracy of the system has also been investigated.

A reliable and efficient rail track defect detection system is essential for maintaining rail track integrity and avoiding safety hazards and financial losses. Eddy current (EC) testing is a non-destructive technique that can be employed for this purpose. The trade-off between spatial resolution and lift-off should be carefully considered in practical applications to distinguish closely spaced cracks such as those caused by rolling contact fatigue (RCF). A multi-channel eddy current sensor array has been developed to detect defects on rails. Based on the sensor scanning data, defect reconstruction along the rails is achieved using an inverse algorithm that includes both direct and iterative approaches. In experimental evaluations, the EC system with the developed sensor is used to measure defects on a standard test piece of rail with a probe lift-off of 4-6 mm. The reconstruction results clearly reveal cracks at various depths and spacings on the test piece.

The application of artificial intelligence to point-of-care testing (POCT) disease detection has become a hot research field, in which breath detection which detects the patient's exhaled VOCs combined with sensor arrays of Convolutional Neural Network (CNN) algorithms as a new lung cancer detection is attracting more researchers' attention. However, due to low accuracy, high complexity computation and large number of parameters make the CNN algorithms difficult transplant to the embedded system of POCT devices. A lightweight neural network (LTNet) in this work is proposed to deal with this problem, and meanwhile, achieve high-precision classification of acetone and ethanol gases, which are respiratory markers for lung cancer patients. Compared to currently popular lightweight CNN models such as EfficientNet, LTNet has fewer parameters (32K) and its training weight size is only 0.155 MB. LTNet achieved an overall classification accuracy of 99.06% and 99.14% in the own mixed gas dataset and the University of California (UCI) dataset, which are both higher than that of the five existing models’, and it also offers the shortest training (844.38s and 584.67s) and inference time (23s and 14s) in the same validation set. Compared to the existing CNN models, LTNet is more suitable for resource-limited POCT devices.

The importance of conflict analysis and safety considerations during work zone intervals at signalized intersections cannot be overstated, as these periods pose unique challenges and safety risks for both motorists and pedestrians. Work zones introduce temporary changes to traffic patterns, lane configurations, and signal timings, which can disrupt the flow of traffic and increase the likelihood of conflicts between vehicles and pedestrians. By conducting comprehensive conflict analysis, it is possible to identify potential conflict points, such as merging areas, pedestrian crossings, and lane transitions, and implement targeted safety measures to mitigate risks. Additionally, considering safety considerations during work zone intervals is paramount to safeguarding the well-being of road users and minimizing the occurrence of conflicts or collisions. Measures such as enhanced signage, temporary traffic control devices, and increased enforcement efforts can help promote compliance with traffic regulations and ensure the safe passage of vehicles and pedestrians through work zones. This study investigates the dynamics of traffic behavior and safety implications within work zones at signalized intersections, aiming to address key challenges and enhance intersection management strategies. Through comprehensive analysis, varying frequencies of Vehicle-to-Vehicle (V2V) conflicts were observed across different movement directions, with significant occurrences identified in specific phases of the traffic signal cycle. Specifically, 69 V2V conflicts in phase #1, 181 in phase #2, 31 in phase #3, 207 in phase #4, 1 in phase #5, 274 in phase #6, 93 in phase #7, and 186 in phase #8 were recorded. Furthermore, the examination of Vehicle-to-Pedestrian (V2P) conflicts underscored the importance of prioritizing pedestrian safety, with notable occurrences observed in phases associated with pedestrian crossing movements. Meanwhile, despite the closure of left-turn movements, instances of red light running persisted, with 69 red light running events in phase #1, 181 in phase #2, 31 in phase #3, 207 in phase #4, 1 in phase #5, 274 in phase #6, 93 in phase #7, and 186 in phase #8.To mitigate these safety concerns during work zone intervals, proactive measures are essential. Strategies include improving communication through clear signage and advanced warning systems, enhancing enforcement efforts with red light cameras and increased police presence, and investing in infrastructure improvements such as temporary pedestrian facilities. Integration of real-time data from sensors, particularly LiDAR technology, offers significant advantages in detecting conflicts and red light runners during work zone intervals. LiDAR's precise, real-time data on vehicle and pedestrian movements, combined with its 360-degree coverage and high spatial resolution, facilitates accurate detection and tracking of potential conflict scenarios, contributing to enhanced intersection safety and traffic management efficiency. This study endeavored to conduct a traffic safety analysis during work zone intervals at a signalized intersection in Baltimore City, known for its high rate of traffic crashes, utilizing LiDAR sensor technology.

This paper presents a two-stage ADC based on pseudo-differential operational transconductance amplifier (OTA), which is designed for the readout circuit of X-ray linear array sensor. This hybrid ADC employs an incremental sigma-delta ADC and a cyclic ADC, achieving a good trade-off between accuracy and conversion speed. The two stages share the same hardware to reduce power consumption and die area. A common-mood feedback module is used to suppress the influence of charge injection, and the effectiveness is demonstrated by detailed theoretical analysis. A test chip of 14-bit ADC is fabricated in 0.35μm CMOS technology. The measured root mean square (RMS) value of DNL is 0.254 LSB, and the maximum value of INL is -0.776/+1.56 LSB. The measured effective number of bits (ENOB) is 13.43 bits.

This paper focuses on optimal sensor positioning for monitoring activities of daily living and investigates different combinations of features and models on different sensor positions, i.e., the side of the waist, front of the waist, chest, thigh, head, upper arm, wrist, and ankle. Sixteen features are extracted and the feature importance is measured by using the Relief-F feature selection algorithm. Eight classification algorithms are evaluated on a dataset collected from young subjects and that collected from elderly subjects, with two different experimental settings. To deal with different sampling rates, signals with a high data rate are down-sampled and a transformation matrix is used for aligning signals to the same coordinate system. The thigh, chest, side of the waist, and front of the waist are the best four sensor positions for the first dataset (young subjects), with average accuracy values being greater than 95%. The best model obtained from the first dataset for the side of the waist is validated on the second dataset (elderly subjects). The most appropriate number of features for each sensor position is reported. The results provide a reference for building activity recognition models for different sensor positions, as well as for data acquired from different hardware platforms and subject groups.

Force reduction is one of the most important benefit of applying ultrasonic vibration on milling. However, most of studies so far are limited to experimental investigation. In the current study, an analytical predictive model on cutting forces in ultrasonic vibration-assisted milling is proposed. The three types of tool-workpiece criteria are considered based on the instantaneous position and velocity of tool center. Type I criterion indicates that there is no contact if the instantaneous velocity is opposite to tool rotation direction. Type II criterion checks whether the vibration displacement is larger than the instantaneous uncut chip thickness. Type III criterion considers the overlaps between current and previous tool paths due to vibration. If none of these criteria is satisfied, milling forces are nonzero. Then the calculation is performed by transforming milling and tool geometry configuration to orthogonal cutting at each instant. The orthogonal cutting forces are predicted through the exhaustive search of shear angle and calculation of shear flow stress on tool-chip interface. The axial force is then calculated based on tool geometry, and the milling forces in feed, cutting, and axial directions are calculated after coordinate transformation. The proposed predictive force model in ultrasonic vibration-assisted milling is validated through comparison to experimental measurements on Aluminum alloy 2A12. The predicted values are able to match the measured milling forces with high accuracy of average difference of 13.6% in feed direction and 13.8% in cutting direction.

In the context of improving aircraft safety, this study focuses on the development and evaluation of a graphene-based ice detection system using an environmental chamber. The research is driven by the need for more accurate and efficient ice detection methods, crucial in mitigating in-flight icing hazards. The methodology employed involves testing flat graphene-based sensors in a controlled environment, simulating a variety of climatic conditions that could be experienced in an aircraft during its entire flight. The environmental chamber enabled precise manipulation of temperature and humidity levels, thereby providing a realistic and comprehensive test bed for sensor performance evaluation. The results were significant, revealing the graphene sensors’ heightened sensitivity and rapid response to the subtle changes in environmental conditions, especially the critical phase transition from water to ice. This sensitivity is the key to detecting ice formation at its onset, a critical requirement for aviation safety. The study concludes that graphene-based sensors, tested under varied and controlled atmospheric conditions, exhibit a remarkable potential in enhancing ice detection systems for aircraft. Their lightweight, efficient and highly responsive nature makes them a superior alternative to traditional ice detection technologies, paving the way for more advanced and reliable aircraft safety solutions.

Wireless Powered Communication Networks (WPCN), which has attracted much attention of researchers, also been recently recommended in 5^th generation (5G) wireless networks. With the help of the WPCN, the reliability and battery life of wireless low-power devices can be improved. In this paper, we investigate throughput and ergodic capacity in WPCN-assisted amplify-and-forward (AF) relaying system, considering two transmission modes including delay-tolerant and delay-limited. As important achievement, we propose symmetric energy harvesting protocol, namely time power switching relaying (TPSR) in order to find maximal throughput. In particular, both time switching and power switching coefficients in this schemes are considered. Unlike most of the previous works, we further focus on impact of outdated channel state information (CSI) in this WPCN. In order to evaluate information processing efficiency, the performance can be substantially improved by optimally harvesting time and power coefficients of the received signal at relay node for energy and information extraction, and by deploying several scenarios. By deploying Monte Carlo simulation, it is confirmed that the system performance is more sensitive to CSI estimation error, noise variance, signal-to-noise ratio (SNR) and resulting in other reasonable computations of TPSR need be deployed to obtain QoS requirement.

Spraying various liquids (primarily aqueous solutions of various substances) is widely used in various technological processes. For most of them, high dispersibility and narrow droplet size distribution are essential. This facilitates ultrasonic spray technique. However, the higher the dispersity of droplets produced by ultrasonic spray, the lower the spray productivity. To solve this problem, we proposed a method of multistage spraying, consisting in generation of a large number of particles of large initial size (to ensure high productivity) and their subsequent destruction by propagation in a periodic ultrasonic field (to ensure small droplet sizes at high productivity). To experimentally determine the capabilities of this technique, a tubular emitter in the shape of a cylinder of stepped-variable cross-section was designed. Configuration of the ultrasonic field inside the emitter (22.2 kHz; 182 dB) implements three-stage spraying (the number of sputtering stages corresponds to the number of anti-nodes along the emitter axis). The effectiveness of proposed and developed technique suitable for generation of droplets sized less than 40 µm with performance exceeding the known ultrasonic spray techniques at least 10 times has been confirmed in the course of conducted research.

On-stream inspections are the most appropriate method for routine inspections during plant operation without going through production downtime. Ultrasonic inspection, one of the on-stream inspection methods, faces challenges when performed at high temperatures exceeding the recommended 52°C. This study aims to determine the ultrasonic velocity and attenuation with the known material grade, thickness, and temperatures by comparing theory calculation versus experiment with temperatures ranging between 30°C to 250°C on low carbon steel covering most petrochemical equipment material and working conditions. The theoretical analysis was to obtain Young's modulus, Poisson's ratio, and longitudinal velocity at different temperatures. The experiments validated the predicted results of ultrasonic change due to temperature increase and showed a maximum error of 3%. The experimental data of velocity and decibel change from the temperature range provide a reference for the future when dealing with unknown materials information on site that require a quick corrosion status determination.

This article discusses the results of a series of experiments on pulse ultrasonic cure monitoring of carbon fiber reinforced plastics applied to the pultrusion process. The aim of this study is to validate the hypothesis that pulse ultrasonic cure monitoring can be applied a) for profiles having small cross sections such as 7x0.5 mm and b) within the environment of the pultrusion process. Ultrasonic transducers are adhesively bonded to the pultrusion tool as actuators and sensors. The time-of-flight and the amplitude of an ultrasonic wave are analyzed to deduce the current curing state of the epoxy matrix. The experimental results show that ultrasonic cure monitoring is indeed applicable even to very thin cross sections. However, significant challenges can be reported when the techniques are used during the pultrusion process.

The market for autonomous vehicles (AV) is expected to experience significant growth over the coming decades and to revolutionize the future of transportation and mobility. The AV is a vehicle that is capable of perceiving its environment and perform driving tasks safely and efficiently with little or no human intervention and is anticipated to eventually replace conventional vehicles. Self-driving vehicles employ various sensors to sense and perceive their surroundings and, also rely on advances in 5G communication technology to achieve this objective. Sensors are fundamental to the perception of surroundings and the development of sensor technologies associated with AVs has advanced at a significant pace in recent years. Despite remarkable advancements, sensors can still fail to operate as required, due to for example, hardware defects, noise and environment conditions. Hence, it is not desirable to rely on a single sensor for any autonomous driving task. The practical approaches shown in recent research is to incorporate multiple, complementary sensors to overcome the shortcomings of individual sensors operating independently. This article reviews the technical performance and capabilities of sensors applicable to autonomous vehicles, mainly focusing on vision cameras, LiDAR and Radar sensors. The review also considers the compatibility of sensors with various software systems enabling the multi-sensor fusion approach for obstacle detection. This review article concludes by highlighting some of the challenges and possible future research directions.

This paper introduces a low-tech capacitive micromachined ultrasonic transducer (CMUT) designed with low environmental footprint materials. The fabrication process involves a copper plate as the fixed bottom electrode, a polymer-based adhesive as a dielectric material, and an aluminum foil as the top electrode.Finite element simulations include studies of displacement, mechanical stresses, and eigenfrequency. Experimental measurements validate the device's electromechanical behavior, showing an eigenfrequency of 88.6 kHz and a displacement of 22 pm. The low-tech CMUT demonstrates potential for applications such as ultrasonic actuation and energy harvesting, offering simplicity, biocompatibility, and low environmental impact. While not directly ready for applications, these transducers provide hands-on experience with technology similar to high-performance silicon-based implementations. These low-tech MUTs are perfect practical case studies for teaching purposes, combining simulation and experimental validation.

Beer fermentation is typically monitored by periodic sampling and off-line analysis. In-line sensors would remove the need for time-consuming manual operation and provide real-time evaluation of the fermenting media. This work uses a low-cost ultrasonic sensor combined with machine learning to predict the alcohol concentration during beer fermentation. The highest accuracy model (R2=0.952, MAE=0.265, MSE=0.136) used a transmission-based ultrasonic sensing technique along with the measured temperature. However, the second most accurate model (R2=0.948, MAE=0.283, MSE=0.146) used a reflection-based technique without the temperature. Both the reflection-based technique and the omission of the temperature data are novel to this research and demonstrate the potential for a non-invasive sensor to monitor beer fermentation.

A compact Mach-zehnder interferometer with a novel design of directional couplers and a phase shifter has been presented as a thermo-optical sensor. With the aim of reducing device size to micro and nano dimension silicon-on-insulator technology was employed. That allowed miniaturization of device size through the reduction of its cross sectional area to 0.066 µm² and the radius of curvature of both the arms of the directional coupler and S-bends of the phase shifter to 5 µm and C-bends to 3 µm. These nano size device dimensions made it possible to reduce the coupling gap to 0.2 µm, which resulted in a significant reduction in the coupling length. The device geometry and its performance characteristics were analyzed and optimized using coupled mode analysis and finite difference time domain simulation tools, respectively. The wavelength dependent transmission loss of the device was measured at different temperature to verify and validate its performance characteristics. Tested devices showed a remarkable temperature dependent transmission characteristic offering significant changes in transmission loss band – with as low as 0.45 ⁰C change in substrate temperature. The extinction ratio and the free spectral range of the device were 26 dB and 0.26 nm respectively in the wavelength range of 1549.5 nm – 1550.5 nm. These results imply that the devices presented here can be used as compact and highly sensitive thermal sensors and optical switches.

This work deals with the evaluation of adhesive single-lap joints using ultrasonic guided waves. An adhesive bonded lap joint can be modelled as a three-layer system made up of two adherents and an adhesive. The propagation of guided waves in the joint is developed from matrix formulations. The behavior of the different guided wave modes that propagate in the bonded region is characterized and it is found that their relative amplitudes can be estimated based on the properties of the incoming wave that propagates in the non-bonded region. It was verified that the excitation of these modes is ruled by the degree in which the shapes of both modes match each other. A 3D simulation of two aluminium bonded plates using 500 kHz ultrasonic transducers in a pitch and catch configuration was implemented using the Matlab k-Wave toolbox. Scattering effects due to some produced defects located in the bond line of the lap joints were simulated. Experimental setup with some artificial defects produced in the aluminum joints were used in order to compare with the simulated. Qualitative agreement was observed for the two approaches. The observed deviation can be due to the different characteristics of the experimental and simulated defects.

To build a stable power factor and high output accuracy, it should use balanced active and reactive power, also used ultrasonic PWM was used with the frequencies (20–500 kHz). I also used a three-phase dynamic load at the output system and was connected to the compound splicing (CS) system this is a novelty. An oscillator circuit with 4Ghz as a microcontroller is a novelty, and designing ADC is utilized to increase accuracy, as well as contribute to the reduction of loss brought on by the characteristics of voltage source inverters (VSI), such as dead time determined by the excess voltage or voltage drop in the inverter, circumstances abnormal to the load current, such as short circuit current in the production phase, and so forth. The innovation relates to the inverter's load sensing circuit, current smoothing during operation, reaction, spontaneous power factor enhancement of the inverter, and correction of reactive power of passive devices. This invention contributes to the advancement of D.C to A.C power converter by the achievement of extremely low losses, excellent precision, and lightweight construction. Additionally, the accuracy ranges from 99%, and the total harmonic distortion (THD) of the voltage and current is (0.1%-0.8%). We Power MOSFET are used, along with FPGA to improve control over the creation of ultrasonic PWM signals, the programmable peripheral interface (PPI) 8255A for regulatory work. The marks serve as proof of this.

Titanium’s accelerating usage in global markets is attributable to its distinctive combination of physical and metallurgical properties. The key to best utilizing titanium is to exploit these characteristics, especially as they complement one another in a given application, rather than to just directly substitute titanium for another metal. Titanium alloy are extensively used in aerospace applications such as components in aero-engines and space shuttles, mainly due to their superior strength to weight ratio. For these demanding applications functionality and reliability of components are of great importance. To increase flight safety, higher sensitivity inspections are sought for rotating parts. Increased sensitivity can be applied at the billet stage, the forging stage, or both. Inspection of the forging geometry affords the opportunity to apply the highest sensitivity due to the shorter material paths when compared to those required for billet inspections. Forging inspection is typically performed for titanium (Ti) rotating parts with immersion inspection and fixed-focus, single-element transducers. Increased gain is required with depth because the ultrasonic beam attenuates with distance and diverges beyond the focus position that is placed near the surface. The higher gain that is applied with depth has the effect of increasing the UT noise with depth. The relationships between the UT noise, selection of the examination technique and the smallest detectable defect are presented in this material.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

Separase is a key cysteine protease to separate sister chromatids through digestion of cohesion ring that inhibits chromosome segregation as trigger of metaphase–anaphase transition in eukaryotes and highly regulated its activity by binding with securin and cyclinB-CDK1 complex. Those bindings prevent proteolytic activity of separase until the onset of anaphase. Chromosome missegregation and aneuploidy are frequently observed in malignancies. However, there are some difficulties for biochemical examinations due to instability of separase in vitro and a few spatiotemporal resolution approaches monitoring live separase activity throughout mitotic processes. Here we have developed FRET-based molecular sensors including GFP variants with separase cleavable sequences as donor and covalently attached fluorescent dye as acceptor molecules applicable to conventional live cell imaging and flow cytometric analysis because of efficient live cell uptake. We investigated performance of equivalent molecular sensors localized or not localized inside nucleus under cell cycle control using flow cytometry. Synchronized cell cycle progression rendered significant separase activity detections in both molecular sensors. We obtained consistent outcomes with localized molecular sensor introduction and cell cycle control by fluorescent microscopic observations. We thus established live cell separase activity monitoring systems specifically or statistically that could lead to elucidate separase properties in detail.

Stess in laser cladding coating is an important factor affecting the safe operation of remanufacturing components. Ultrasonic testing has become a hot direction in nondestructive evaluation of stress, because it has the advantages of safety, non-destructive and on-line detection. This paper provides a review of ultrasonic testing for stress in remanufacturing laser cladding coating. It summarizes the recent research outcomes on ultrasonic testing for stress, analyzes mechanism of ultrasonic testing for stress. Remanufacturing laser cladding coating shows typical anisotropic behaviors, the ultrasonic testing signal in laser cladding coating is influenced by many complex factors, such as microstructure, defect, temperature and surface roughness, etc. At present, ultrasonic testing for stress in laser cladding coating can only be done roughly. The paper discusses active mechanism of micro / macro factors to the reliability of stress measurement and the impact of stress measurement to the quality and safety of remanufacturing components. Base on the discussion, the paper proposes strategies for acquisition of nondestructive, rapid and accurate measurement of stress in remanufacturing laser cladding coating.

The increasing focus on the development of positioning techniques reflects the growing interest in applications and services based on indoor positioning. Many applications necessitate precise indoor positioning or tracking of individuals and assets, leading to rapid growth in products based on these technologies in certain market sectors. Ultrasonic systems have already proven effective in achieving the desired positioning accuracy and refresh rates. The typical signal used in ultrasonic positioning systems for estimating the range between the target and reference points, specifically the linear chirp, can undergo shape aberration due to the effects of acoustic diffraction when the aperture exceeds a certain limit. The extent of the aberration is influenced by the shape and size of the transducer, as well as the angle at which the transducer is observed by the receiver. This aberration also impacts the shape of the cross-correlation, causing it to lose its characteristic easily detectable single global peak. In such instances, cross-correlation techniques yield results with a significantly higher error than anticipated. In this study, an alternative technique to global peak detection is proposed, leveraging the inherent symmetry observed in the shape of the aberrated cross-correlation. The numerical simulations, performed using the academic acoustic simulation software Field II, conducted using a typical ultrasonic chirp and ultrasonic emitter, compare the classical and the proposed range techniques in a standard office room. The results demonstrate that the proposed technique enables accurate range estimation even in the presence of severe cross-correlation shape aberrations. This allows the use of emitting transducers with a much larger aperture than that allowed by the classical cross-correlation technique. Consequently, it becomes possible to have greater acoustic power available, leading to improved Signal-to-Noise Ratio (SNR).

In this work, we describe the optimization of carbon-based electrodes employed in Bio-Electrochemical Systems (BES) by the deposition on commercial carbon paper electrodes of nanostructured layers of poly(3,4-ethylene-dioxy-thiophene) poly(styrene-sulfonate) (PEDOT:PSS) via Ultrasonic Spray Coating (USC). This innovative application of USC allowed us to demon-strate that uniform and controlled depositions of PEDOT:PSS can be successfully obtained on car-bon-based electrodes. We characterized the morphology and verified the spatial uniformity of depositions via scanning electron microscopy and Raman spectroscopy. Electrochemical charac-terizations on fabricated electrodes demonstrated a more than two-fold increase in electrochemi-cal active surface area with respect to bare carbon paper. A lab-scale experiments on BES was performed selecting Microbial Fuel Cells (MFCs) as the reference devices. Devices featuring USC-deposited PEDOT:PSS electrodes showed a three-fold higher Energy recovery with respect to con-trol cells, reaching a maximum value of (13 ± 2) J·m−3. Furthermore, the optimal PEDOT:PSS con-centration for the MFCs improvement is in line with the values reported in the literature for other deposition methods. In conclusion, this work demonstrates that USC is a promising technique for application in BES.

Structural health monitoring of lightweight constructions made of composite materials can be performed using guided ultrasonic waves. If modern fiber metal laminates are used, this requires integrated sensors that can record the inner displacement oscillations caused by the propagating guided ultrasonic waves. Therefore, we have developed a robust MEMS vibrometer that can be integrated with structural and functional compliance. This vibrometer is directly sensitive to the high-frequency displacements from structure-borne ultrasound when excited between its first and second natural frequency. The vibrometer is mostly realized by processes earlier developed for a pressure sensor but with additional femtosecond laser ablation and wafer bonding. The piezoresistive transducer made from silicon is encapsulated between top and bottom glass lids. The natural frequencies are experimentally determined using an optical micro vibrometer setup. The vibrometer functionality and usability for structural health monitoring are demonstrated on a customized test rig by recording application-relevant guided ultrasonic wave packages with a central frequency of 100 kHz at a distance of 200 mm from the exciting ultrasound transducer.

Brushless Synchronous Machines (BSM) are replacing conventional synchronous machines with static excitation in generation facilities due to the absence of sparking and lower maintenance. However, this excitation system makes challenging measuring electric parameters in the rotor. This fact highly difficult the detection of ground faults, which are the most common type of electrical fault in electric machines. In this paper, a ground fault detection method for BSM is proposed. It is based on an inductive AC/DC rotating current sensor installed in the shaft. In case of a ground fault in the rotating parts of the BSM, a fault current will flow through the rotor’s sensor, inducing voltage in its stator. Analyzing the frequency components of the induced voltage the detection of a ground fault in the rotating elements is possible. The ground faults detection method proposed covers the whole rotor and discern between DC and AC sides. To corroborate the detection method, experimental tests have been performed using a prototype of this sensor connected to laboratory synchronous machines achieving satisfactory results.

This study explores the use of remote ultrasound vibration to enhance welding strength. It examines the effects of 20 kHz, and 40 kHz High Power Ultrasound Transducers (HPUT) in contact and contactless modes during ultrasonic assistance laser welding. Employing shear tests and microscopy for assessment, the research evaluates ultrasound's impact on welding strength and identifies the optimal transducer. Theoretical and numerical analyses investigate vibration transmission into the welding area, particularly examining the vibration distribution and cavitation initiation within the molten pool area. Results indicate that ultrasound-assisted welding increases pull test performance, including the resistance force and strain, and improves microscopic structural integrity. Numerical simulations suggest that narrow-band vibration intensifies pressure in specific welding zones. Contactless ultrasound application also shows enhanced welding quality, offering a promising alternative to current methods. This work contributes to electric car technology by suggesting improvements in welding techniques for power battery systems.

Purpose Professional oral hygiene procedures are recommended by dentists, twice a year. BioHPP is a polyetheretherketone polymer used in prosthetic dentistry as a frame material. The aim was to investigate whether routine dental cleaning procedures such as ultrasonic scaling and brushing affect the surface proprieties of prosthetic BioHPP restorations. To evaluate the surface properties of different restorations based on BioHPP (veneered with composite resin and polished) after brushing and ultrasonic scaling exposure. Materials and Methods The 66 BioHPP specimens were divided into three groups (n=22). The first group was the control group, and no further treatment was applied. The specimens in the second group were veneered with composite resin and in the third group the specimens were veneered with composite resin and polished. Each group of samples was divided into 3 subgroups: 0- no treatment, 1-exposed to tooth brushing, 2-exposed to ultrasonic scaling. The surface morphology was investigated by atomic force microscopy (AFM). The structure of samples was analysed using the XRD technique, and the surface wettability was done. Results Control group specimens were significantly rougher compared to other groups (p ≤ 0.05). There was no statistically significant difference in the contact angle of water analyses between the samples. Conclusion: Composite veneered BioHPP showed the highest surface resistance to brushing and ultrasonic scaling.

Nonwoven fabrics have been widely used in textile manufacturing industry as a sheet or web structure because of soft, water-repellent, recycle, ecological and resilient functions. Ultrasonic welding method has been applied for bonding nonwoven fabrics due to clean, fast and reliable approach. In this work, the ultrasonic stepped horn is designed to generate uniform amplitudes on the working surface by using finite element analysis (FEA) simulation. Chromium carbon steels are utilized to produce ultrasonic horns due to high wear resistant and hardness. Isotactic polypropylene nonwoven fabrics fabricated by spunbond process were bonded by continuous ultrasonic sewing machine. Ultrasonic horn with 70 mm in diameter working at 20 kHz, polypropylene (PP) nonwoven density of 80 gsm and various design of welding joints were applied. A typical image in the case of number one was investigated by the scanning electron microscope (SEM) images of inter-facial micro-structure. However, welding joints of totally eight roller patterns was test the tensile strength of the ultrasonic welding joints on PP nonwoven fabrics. The tensile strength of the welding joints is proportional to the area ratio between the welding area and cycling area. The results showed that the melted zone without welding defects such as crack or blowhole can be seen. Furthermore, the tensile strength of welding joints in eight cases of roller patterns (No.1-No.8) was described in details. The ultrasonic welding joints with brick structures give higher tensile strength while the solid line in the pattern gave less strength.

The article is devoted to the study of ultrasonic agglomeration of PM2.5 in uniform and non-uniform ultrasonic fields. The possibility of increasing the efficiency of ultrasonic agglomeration by initiating acoustic streams in a resonant non-uniform ultrasonic field is shown. A non-uniform ultrasonic field with zones of high and low sound pressure levels formed using a bending-oscillating disk transmitter made it possible to initiate acoustic vortex-type streaming that promote the movement of particles into the nodal areas of a standing wave and between them. The efficiency of ultrasonic treatment was determined indirectly by the degree of inertial trapping of agglomerates. It has been established that the impact of an non-uniform ultrasonic field in comparison with the impact of a uniform ultrasonic field makes it possible to increase the efficiency of inertial capture of agglomerates PM2.5 from 89% to 95%, PM1.5 from 85% to 92%, PM0.5 from 76% to 85%. The results obtained made it possible to propose a design for an agglomeration chamber, which allows for a multiple increase in the productivity of ultrasonic processing of a gas-dispersed flow.

CO₂ enhanced oil recovery (EOR) has been proven its capability to explore the unconventional tight oil reservoirs and potential for geological carbon storage. Meanwhile, the extremely low permeability pores exaggerate the difficulty CO₂ EOR and geological storage processing in the actual field. This paper initiates the ultrasonic-assisted approach to facilitate the oil-gas miscibility development and finally contribute to unlock more tight oils. First, the physical properties of crude oil with and without ultrasonic treatments were experimentally analysed through gas chromatography (GC), Fourier-transform infrared spectroscopy (FTIR) and viscometer. Second, the oil-gas minimum miscibility pressures (MMPs) were measured from the slim-tube test and the miscibility developments with and without ultrasonic treatments were interpreted from the mixing-cell method. Third, the nuclear-magnetic resonance (NMR) assisted coreflood tests were conducted to physically model the recovery process in porous media and directly obtain the recovery factor. Basically, the ultrasonic treatment (40KHz and 200W for 8 hours) was found to substantially change the oil properties, with viscosity (at 60°C) reduced from 4.1 to 2.8mPa·s, contents of resin and asphaltene decreased from 27.94% and 6.03% to 14.2% and 3.79%, respectively. The FTIR spectrum shows the unsaturated C-H bond, C-O bond and C≡C bond in macromolecules were broken from ultrasonic, which caused the macromolecules (e.g., resin and asphaltenes) to be decomposed into smaller carbon-number molecules. Accordingly, the MMP was determined to be reduced from 15.8 to 14.9MPa from the slim-tube test and the oil recovery factor increased by over 10%. This study reveals the mechanisms of ultrasonic-assisted CO₂ miscible EOR in producing tight oils.

in our increasingly interconnected world, sensor networks are critical in gathering and sending data for various applications, from environmental monitoring and industrial automation to healthcare and smart cities. However, as sensor networks expand in importance, so does the need to solve the multidimensional concerns of security, privacy, and forensics. This article explores the complex world of sensor network security, the delicate balance between data privacy and utility, and the emerging area of sensor network forensics. This article focuses on risk assessment of a network.

In this work, we report manganese phthalocyanine (MnPc) films obtained by ultrasonic spray-pyrolysis technique at 40°C deposited on glass substrate subjected to thermal annealing at 100 °C and 120°C. The MnPc films were characterized by UV/Vis spectroscopy, Raman spectroscopy, X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM). The absorption spectra of the MnPc films were studied in a wavelength range from 200 to 850 nm, where the characteristic bands of a metallic phthalocyanine known as B and Q bands were observed in this range of the spectrum. The optical energy band (Eg) was calculated by the Tauc equation. It was found that for these MnPc films, the Eg has the values of 4.41, 4.46 and 3.58 eV corresponding to as deposited, annealing 100°C and 120°C, respectively. The Raman spectra of the films showed their characteristic vibrational modes of the MnPc films. In X-ray diffractograms of these films, the characteristic diffraction peaks of a metallic phthalocyanine are observed, presenting a monoclinic phase. SEM images of these films were studied in cross section obtaining thicknesses of 2, 1.2 and 0.3 μm to as deposited, annealing 100°C and 120°C, successively. Also, in the SEM images of these films, both the average particle sizes ranging from 4 to 0.041 µm and the average diameter from 4.8 to 0.091 μm were obtained. The results agree with those reported in the literature for MnPc films deposited with other techniques.

In this study, a novel flexible ethanol gas sensor was created by the deposition of CoFe2O4 (CFO) thin film was on a thin mica substrate using pulsed laser deposition. Transition electron microscopy (TEM) investigations clearly demonstrated the successful growth of CFO on the mica, where a well-defined interface was observed. Ethanol gas-sensing studies showed optimal performance at 200 °C, with the highest response, 19.2, to 100 ppm ethanol. Operating the sensor in self-heating mode under 7 V applied voltage, which was corresponds to a temperature of approximately 200 °C, produced a maximal response to ethanol of 19.2. This aligned with the highest responses observed during testing at 200 °C, confirming the sensor’s accuracy and sensitivity to ethanol under self-heating conditions. In addition, the sensor exhibited good selectivity to ethanol and excellent flexibility; maintaining its high performance after bending and tilting up to 5000 times. As this is the first report on flexible self-heated CFO gas sensors, we believe that this research holds great promise for the future development of high-quality sensors based on this approach.

Ischemia, the inadequate blood flow, can arise from pre-existing or traumatic events, remain an undetectable issue, and impact the body's ability to provide oxygen to necessary limbs, organs, muscles, or tissue. New technology involving wearable ultrasonic devices allows medical professionals to gain real-time insight into the cardiovascular system of their patients. A non-invasive, postage-stamp-sized ultrasonic sensor can be attached to a patient, allowing for continuous monitoring of the patient’s blood pressure outside of the hospital. After reviewing 16 papers on ultrasonic sensors, this paper intends to review the current use of wearable ultrasonic sensors and the advantages and limitations of the technology used to obtain accurate blood pressure readings. This review will bring attention to the evolving and expanding world of wearable ultrasonic sensors for medical applications.

This review article is focused on the analysis of the state of the art of sensors for guided 9 ultrasonic waves for the detection and localization of impacts, therefore of interest for the structural 10 health monitoring (SHM). The recent developments in sensor technologies are then reported and 11 discussed through the many references in recent scientific literature. The physical phenomena re-12 lated to impact event and the main physical quantities are then introduced to discuss their im-13 portance in the development of the hardware and software components for SHM systems. An im-14 portant aspect of the article is the description of the different ultrasonic sensor technologies cur-15 rently present in the literature and what advantages and disadvantages they could bring, in relation 16 to the various phenomena investigated. In this context, the analysis of the front-end electronics is 17 deepened, the type of data transmission both in terms of wired and wireless technology and in terms 18 of online and offline signal processing. The integration aspects of sensors for the creation of net-19 works with autonomous nodes with the possibility of powering through energy harvesting devices 20 and the embedded processing capacity is also studied. Finally, the emerging sector of processing 21 techniques using deep learning and artificial intelligence concludes the review by indicating the 22 potential for the detection and autonomous characterization of the impacts.

Metal fabrications experience complex physical metallurgical processes during additive manufacturing, leading to residual stress and coarse microstructure with directional growth. It significantly affects the comprehensive performance of the fabrications, which limits the application of additive manufacturing. Ultrasonic impact treatment (UIT), as a strengthening means to assist additive manufacturing, can effectively improve the stress state and refine the microstructure and the comprehensive performance. This paper introduces the effect of UIT on AM metal fabrications on microstructure morphology, stress distribution, surface roughness, internal defects, and comprehensive performance to gain a deeper understanding of the role of UIT on additively manufactured metal fabrications, which is based on the working principle and effect of process parameters. In addition, the strengthening mechanism of UIT in additive manufacturing is described from the perspective of surface plastic deformation and substructure formation, providing support for the shape and property control of metal fabrications in the process of additive manufacturing assisted by UIT. Finally, the issues that need to be studied in depth on UIT in additive manufacturing are summarized, and an outlook on future research directions is taken.

The integration of Wireless Sensor Networks (WSNs) into agricultural areas has had a significant impact and has provided new, more complex, efficient, and structured solutions for enhancing crop production. This research reviews the role of Wireless Sensor Networks (WSNs) in monitoring the macro-nutrient content of plants. The review study focuses on identifying the types of sensors used to measure macro-nutrients, determining sensor placement within agricultural areas, implementing wireless technology for sensor communication, and selecting device transmission intervals and ratings. The study of NPK (Nitrogen, Phosphorus, Potassium) monitoring using sensor technology in precision agriculture is of high significance in efforts to improve agricultural productivity and efficiency. In addition to fostering technological innovations and precision farming solutions, in future this research aims to increase agricultural yields, particularly by enabling the cultivation of certain crops in locations different from their original ones.

The production of instant green tea requires hot-water extraction, which is time consuming and contributes to losses in aromatic compounds. In this study, an ultrasonic-assisted technology was used to improve the extraction efficiency of green tea, thereby shortening extraction time from 45 to 15 min. In pure water, the dissolution of caffeine and theanine did not change significantly, but total catechin dissolution increased by 0.23 mg/mL and total tea polyphenol dissolution decreased by 3.2 mg/mL. In 76.2% ethanol, the dissolution of caffeine and theanine did not change significantly, but total catechin dissolution increased by 1.57mg/mL and total tea polyphenol dissolution decreased by 1.5 mg/mL. Additionally, we used microwave-assisted technology to further improve the extraction efficiency of green tea, which shortened the extraction time to 2 min. However, the extraction rate remained unchanged. In pure water, the dissolution of caffeine and theanine did not change significantly, but the dissolution of total catechins increased by 0.41 mg/mL and the dissolution of tea polyphenols decreased by 2.9 mg/mL. Ultrasonic treatment increased the proportion of 3-hydroxybutan-2-one, (5S)-5-(hydroxymethyl)oxolan-2-one and 2-phenylethanol, which were the main aroma compounds in tea. Microwave treatment changed the aroma compounds in tea, causing losses in aroma compounds with low boiling point and maintaining (5S)-5-(hydroxymethyl)oxolan-2-one. The taste and aroma of instant green tea improved based on sensory evaluation results.

The major goal of this work is to present a novel fractional temperature-dependent boundary element model (BEM) for solving thermoelastic wave propagation problems in smart nanomaterials. The computing performance of the suggested methodology was demonstrated by using stable communication avoiding S-step – generalized minimal residual method (SCAS-GMRES) to solve discretized linear BEM systems. The benefits of SCAS-GMRES are investigated and compared to those of other iterative techniques. The numerical results are graphed to demonstrate the influence of fractional, piezoelectric, and length scale characteristics on total force-stresses. These findings also demonstrate that the BEM methodology is practical, feasible, effective, and has superiority over domain methods. The results of the present paper help to develop the industrial uses of smart nanomaterials.

This paper investigates the use of contactless power ultrasonic excitation to decrease the electrical impedance of the weld in laser welding. The literature extensively documents the impact of em-ploying contact power ultrasonic excitation on the microstructure morphology and refinement of grain in the weld. This study involves characterizing an industrial High Power Ultrasound Transducer (HPUT) by determining the optimal distance and angle for contactless excitation of the fusion zone in the weld, aiming to achieve the maximum amplitude. Subsequently, the transducer is integrated into the laser welding system, resulting in the creation of an ultrasonic-assisted welding system. To find the improvement due to the contactless vibration assistance, the welding area was char-acterised by an impedance ohmmeter device. The results indicate an approximately 6 % im-provement in the welding quality in terms of the impedance value, an important parameter for battery pack welding. In response to the issue of overheating in the industrial transducer during prolonged welding operations, an alternative transducer was proposed to overcome this challenge. Further investigations are carried out by the alternative transducer to find the effect of different wave types, namely, shear and compressional waves, on the welding quality. The contact vibration can excite the plate approximately 50 times higher in acceleration amplitude than contactless ex-citation. Nevertheless, enhancements of 10% and 6% are observed in the impedance value when utilising compressional and shear waves, respectively, as compared to the results obtained with contactless vibration.

: Testosterone masculinizes male sexual behavior through an organizational effect during the perinatal period. We previously reported that the emission of ultrasonic vocalizations (USVs) in male mice was dependent on the organizational effects of testosterone; females treated with testosterone in the perinatal period had increased USV emissions compared to males. Recently, it was revealed that male USVs have various acoustic characteristics and these variations were related to behavioral interactions with other mice. In this regard, the detailed acoustic character changes induced by testosterone have not been fully elucidated. Here, we revealed that testosterone administered to female mice during the perinatal period modulated the acoustic characteristics of USVs. There was no clear difference in acoustic characters between males and females. Call frequencies were higher in TP-treated males and females compared to control males and females. When the calls were classified into nine types, there was also no distinctive difference between males and females, but TP increased the number of calls with a high frequency, and decreased the number of calls with a low frequency and short duration. The transition analysis by call type revealed that even though there was no statistically significant difference, TP-treated males and females had a similar pattern of transition to control males and females, respectively. Collectively, these results suggest that testosterone treatment can enhance the emission of USVs in females, but the acoustic characteristics are not the same as those of intact males.

Cement paste backfill (CPB) is an effective waste management method allowing the storage of fine process tailings into underground mined-out voids. CPB performance generally depends on the sulfur content of the tailings and the type of binder. In recent years, there has been an in-creasing trend on the use of alkali-activated slag (AAS) to improve the performance properties of CPB. This study focuses on the ultrasonic and microstructural investigation of the effect of slag fineness on the mechanical, geochemical and durability properties of CPB made up of AAS (AAS-CPB) over 360 days. In this scope, AAS-CPB samples were prepared at three different fineness (3100-4650-6300 cm2/g). Fineness of slag significantly improved the early age- and long-term strength (~2.3 fold and ~6.6 fold, respectively) of CPB. However, further increase of slag fineness may have adverse effect on CPB microstructure and strength in the long term. Ultrasonic pulse velocity monitoring displayed very high relation with the strength evolution and durability assessment of CPB. Slag fineness at a degree was seen to improve the pore structure evolution of AAS-CPB. Microstructural studies are in good agreement with the geochemical and durability behavior of AAS-CPB. Microstructural and ultrasonic findings suggest that while slag fineness enhances the mechanical properties of AAS-CPB, further increase of the fineness of slag has no additional important technical advantages.

Cracking in a wide array of industrial components and structures pose a significant threat to their integrity. Detecting cracks using ultrasonic inspection techniques is a widespread activity for economic reasons but there are limitations to the techniques due to the morphology of cracks, such as fatigue cracks. In addition to detection there is a need to measure the size of the cracks which are often within the volume of the material. Ultrasonic techniques are well-suited to look inside the volume of the material but achieving sufficient sensitivity to the tip of the cracks in particular is practically difficult. Without an accurate knowledge of where the tip of the crack lies there can be significant uncertainty in sizing measurements. Machine Learning (ML) techniques are being developed to aid in the inspection and monitoring tasks but presenting the ultrasonic data in a suitable way for ML is very important. Following on from recent work presenting the development of the snooker algorithm to create images termed parameter-spaces, this paper presents how these images can be input into neural network based ML systems to automatically size these critical cracks.

This work investigates the use of Non-destructive tests as a tool for monitoring the structural performance of concrete structures. The investigation encompassed four phases; the first of which involved the use of destructive and non-destructive mechanisms to assess concrete strength on cube specimens. The second phase research focused on site assessment for a twin engineering theatre located at the Faculty of Engineering, University of Lagos using rebound hammer and ultrasonic pulse velocity tester. The third phase was the use of linear regression analysis model with MATLAB to establish a relationship between calibrated strength as well as ultrasonic pulse velocities with their corresponding compressive strength values on cubes and values obtained from existing structures. Results show that the root-mean squared-R² values for rebound hammer ranged between 0.275 and 0.742 while ultrasonic pulse velocity R² values were in the range of 0.649 and 0.952 for air curing and water curing systems respectively. It initially appeared that the Ultrasonic pulse velocity was more suitable for predicting concrete strength than rebound hammer but further investigations showed that the latter was adequate for early age concrete while the former was more suited for aging concrete. Hence, a combined use is recommended in this work.

The monitoring of maternal and child health, using wearable devices made with wireless sensor technologies, is expected to reduce maternal and child death rates. Wireless sensor technologies have been used in wireless sensor networks to enable the acquisition of data for monitoring machines, smart cities, transportation, asset tracking, and tracking of human activity. Applications based on wireless body area network (WBAN) have been used in healthcare for measuring and monitoring of patient health and activity through integration with wearable devices. Wireless sensors used in WBAN can be cost-effective, enable remote availability, and can be integrated with electronic health record (EHR) management systems. Interoperability of WBAN sensor data with other linked data has the potential to improve health for all, including maternal and child health through the improvement of data access, data quality and healthcare access. This paper presents a survey of the state-of-the-art techniques for managing WBAN sensor data interoperability. The findings in this study will provide reliable support to enable policymakers and health care providers to take action to enhance the use of e-health to improve maternal-child health and reduce the mortality rates of women and children.

The aim of this review is to provide a survey of the recent advances and the main remaining challenges related to the ultrananocrystalline diamond (UNCD) nanowires and other nanostructures which exhibit excellent capability as the core components for many diverse novel sensing devices, due to the unique material properties and geometry advantages. The doping introduced in the gas phase during deposition promotes p-type or n-type conductivity. With the establishment of the UNCD nanofabrication techniques, more and more nanostructure based devices are being explored in measuring basic physical and chemical parameters via classic and quantum methods, as exemplified by gas sensors, ultraviolet photodetectors, piezoresistance effect based devices, biological applications, and nitrogen-vacancy color center based magnetic field quantum sensors. Highlighted finally are some of the remaining challenges and future outlook in this area.

Ultrasonic sensors are inexpensive and can take measurements with high accuracy, even with simple hardware configurations, so they are used in various fields. When multiple ultrasonic sensors exist in the measurement space, crosstalk occurs due to other nodes, which causes measurement errors. Crosstalk includes not only receiving homogeneous signals from other nodes, but also overlap by other signals, and interference by heterogeneous signals. This paper proposes a method that uses frequency sweep keying modulation to be robust against overlap and a faster region-based convolutional neural networks (R-CNN)-based demodulator to reduce the interference caused by heterogeneous signals. The demodulator works by training faster R-CNN with the spectrograms of various received signals and classifying the received signals using a faster R-CNN. Experiments implementing an ultrasonic crosstalk environment showed that compared to on-off keying (OOK), phase-shift keying (PSK), and frequency-shift keying (FSK), the proposed method can implement CDMA even with shorter codes, and is robust against overlap. Compared to correlation-based frequency sweep keying, the time-of-flight error was reduced by approximately 75%. While existing demodulators did not consider heterogeneous signals, the proposed method ignored approximately 99% of the OOK and PSK signals, and approximately 79% of the FSK signals. The proposed method performs better than the existing methods and is expected to be used in various applications.

The guided ultrasonic wave (GUW) is extensively employed in non-destructive testing (NDT) for the purpose of detecting defects in aerospace vehicles, oil pipelines and mechanical equipment. The filtration of GUW signals, which often contain substantial environmental noise, is a crucial procedure in signal processing. This paper presents a novel denoising approach that combines Variational Mode Decomposition (VMD) with an enhanced Singular Value Decomposition (SVD). The VMD method is employed to preprocess the initial signal, thereby segregating the signal component from the noise component. Subsequently, the SampEn-SVD (Sample Entropy-SVD) method is utilized to extract the effective component from the VMD-preprocessed noise component. Finally, the VMD-preprocessed signal component and the SampEn-SVD-processed effective component are combined to yield the resultant signal, which effectively filters out the noise. The efficacy of this integrated denoising approach is substantiated through the examination of experimental signals. Furthermore, a comparative analysis is conducted to evaluate the efficacy of this method in relation to other denoising techniques. The results indicate that the SampEn-SVD method yields a superior signal-to-noise ratio (SNR) when processing the GUW signal transmitted through the steel strand. Moreover, the denoising procedure significantly reduces the discretization of characteristic parameters in the signal waveform, thereby addressing the issue of inadequate reproducibility in testing outcomes. Consequently, the denoised signal exhibits high fidelity and demonstrates a strong correlation between its combined eigenvector and strand stress.

The main objective of the paper is to investigate the wave propagation behaviour in composites using numerical and experimental methods. Specifically, the study focuses on the actuation of waves by two PZT transducers placed on the surface and embedded at different positions within the composites, namely the quarter and middle positions. The numerical analysis provides simulated results, while the experimental analysis involves practical testing. The paper demonstrates that the numerical results are consistent with the experimental findings. It is observed that when the PZT transducers are placed at deeper positions within the composites, the peak amplitude of the first wave packet for the A0 mode decreases. Overall, the paper contributes to the understanding of wave propagation in composites by comparing the effects of different positions of PZT transducers, both on the surface and embedded within the material. The findings highlight the influence of transducer placement on wave characteristics, particularly the reduction in peak amplitude with deeper transducer positioning.

Nonlinear ultrasonic testing has been accepted as a promising manner for evaluating material integrity in an early stage. Stress fatigue is the main threats to train safety, railways examinations for stress fatigue are more significant and necessary. A series of ultrasonic nonlinear wave experiments are conducted for rail specimens extracted from railhead with different degree of fatigue produced by three-point bent loading condition. The nonlinear parameter is the indicator of nonlinear waves for expressing the degree the fatigue. The experimental results show that the sensitivity of a third harmonic longitudinal wave is higher than second harmonic longitudinal wave testing. As the same time, collinear wave mixing shows strong relative with fatigue damages than a second longitudinal wave NDT method and provides more reliable results than third harmonic longitudinal waves nonlinear testing method.

Detection of early stage corrosion on slender steel members is crucial for preventing buckling failures of steel structures. An active photoacoustic fiber optic sensors (FOS) system has been reported for early stage steel corrosion detection of steel plates and rebars using surface ultrasonic waves. The objective of this paper is to investigate the surface corrosion/rust detection problem on steel rods using numerically simulated surface ultrasonic waves. The finite element method (FEM) is applied in simulating the propagation of ultrasonic waves on steel rod models. Transmission mode of damage detection is adopted, in which one source (transmitter) and one sensor (receiver) are considered. In this research, radial displacements at the receiver were simulated and analyzed by short-time Fourier transform (STFT) for detecting, locating, and quantifying a surface rust located between the transmitter and the receiver. From our time domain and frequency domain analyses, it is found that the presence, location, and dimensions (length, width, and depth) of surface rust can be estimated by ultrasonic waves propagating through the surface rust.

An effective method to inspect inaccessible nuclear power facility by interface wave which propagate along the shrink fit boundary of reactor head is proposed in this study. Reactor head is relatively thick to inspect from the outside of reactor by conventional ultrasonic testing. The proposed interface wave can propagate a long distance from the fixed transducer position. The inside of nuclear reactor is limited to access due to the high radiation, so transducers are located at outside of nuclear facility and interface wave propagates into the nuclear reactor for defect detection. The numerical simulation and experiments were carried out to validate the effectiveness of the proposed interface wave inspection method. Various defect cases simulating field failures are also presented with satisfactory detectability by the proposed technique with the features for defect classification.

The 1060 aluminium alloy is widely applied to electronic industry, construction area, aerospace field, traffic engineering, decoration and consumption goods market for its good chemical, physical and mechanical properties. In general, excellent processing property is necessary and important for manufacturing of complicated panels. In this paper, a special 2D ultrasonic vibration incremental forming method is designed to improve its plasticity and mechanical properties. Three kind of processing methods including traditional single point incremental forming, longitudinal ultrasonic vibration incremental forming and 2D ultrasonic vibration incremental forming are conducted for flexible manufacture of conical parts of 1060 aluminium alloy sheet. Then micro-hardness tests, residual stress tests and scanning electron microscopy tests are carried out to probe its revolution of micro-structure and mechanical properties and to analysis the effects of different types of ultrasonic vibration on plasticity and fracture characteristic of 1060 aluminium alloy. It is proved that 2D ultrasonic vibration is facilitated to improvement of plasticity and surface qualities of 1060 aluminium alloy than the other two processing methods. So, the novel 2D ultrasonic vibration incremental forming possesses substantial application values on flexible and rapid manufacturing of complicated thin-walled component of aluminium alloy.

Statistical based reconstruction methods and signal processing tooling techniques are implemented and used to detect delaminations or debondings within composite items. From literature it appears that, although a single procedure for the estimation of the structural health is a fast solution, a multiple analysis based on different reconstruction methods or different damage parameters could provide more detailed information about the location and the severity of possible failures. This work discusses the advantage of using cross-correlation analysis in a data-driven approach based on ultrasonic guided waves (GW) tomographic technique and piezoelectrics (PWAS) in pitch-catch configuration. In this sense, this work evidences an improvement in damage detection when the cross-correlation is included as part of the GW-based system for damage assessment approach. The specimens used as test structures to demonstrate the validity of the methodology derive from an aircraft wing test article where damages are specified as skin delamination produced by low energy impact.

This work introduces a neuromorphic sensor based on force-sensing resistors (FSR) and spiking neurons for robotic systems. The proposed sensor integrates the FSR in the schematic of spiking neuron in order to make the sensor to generate spikes with frequency that depends on the applied force. The performance of the proposed sensor is evaluated for the control of a SMA-actuated ro-botic finger by monitoring the force during steady state when the finger pushes on a tweezers. For comparison purposes, we performed similar evaluation when the SNN receives input from a widely used compression load cell (CLC). The results show that the proposed FSR based neuro-morphic sensor has very good sensitivity to low forces and the function between the spiking rate and the applied force is continuous with good variation range. However, when compared to the CLC, the proposed sensor has lower linearity of the response, but it benefits from two orders of magnitude lower power consumption. These aspects imply that the neuromorphic sensor based on FSR are useful for bioinspired control of humanoid robotics representing a low power and low cost alternative the widely used sensors.

Classical and optimal control architectures for motion mechanics with fusion of noisy sensors use different algorithms and calculations to perform and control any number of physical demands, to varying degrees of accuracy, precision, and cost. Their performances are tested for the purpose of comparison through the means of a Monte Carlo simulation that simulates how different parameters might vary under noise, representing real-world imperfect sensors. We find that improvements in one figure of merit often come at a cost in the performance in the others, especially depending on the presence of noise in the system sensors. If sensor noise is negligible, open-loop optimal control performs the best. However, in the overpowering presence of sensor noise, using a control law inversion patching filter performs as the best replacement, but has significant computational strain.

This article uses machine learning analysis of wearable sensor data to explore the topic of driver differentiation. The study focuses on using detailed analyzes of data collected from wearable sensors to identify patterns that differentiate skilled drivers from inexperienced ones. On a predetermined driving route, participants experienced a variety of driving conditions, including parking, navigating cities, driving on highways and driving through residential neighborhoods. The gathered data was analyzed using machine learning techniques, yielding a classification accuracy of 94% overall. The results highlight important differences in sensor data between inexperienced and experienced drivers, providing insight into possible uses for improving safety protocols, driver education, and personalized feedback systems. The article fosters improvements in traffic safety and driver education by offering insightful information on the link between driver behavior analysis and machine learning.

In the current scenario, liver abnormalities are one of the most serious public health concerns. Cirrhosis of the liver is one of the foremost causes of demise from liver diseases. To accurately predict the status of liver cirrhosis, physicians frequently use automated computer-aided approaches. In this paper the clustering techniques like Fuzzy C Means (FCM), Possibilistic Fuzzy C Means (PFCM), Possibilistic C Means (PCM), Sample Entropy features are extracted from normal and cirrhotic liver ultrasonic Images. The extracted features are classified as normal and Cirrhosis one through Gaussian Mixture Model(GMM), Softmax Dis(SDC), Harmonic Search Algorithm (HSA), SVM(Linear), SVM(RBF), SVM(Polynomial), Artificial Algae Optimization (AAO) and hybrid classifier Artificial Algae Optimization (AAO) with Gaussian Mixture Mode (GMM). The classifiers performances are compared based on Accuracy, F1 Score, MCC, F Measure, Error rate and Jaccard metric (JM).The hybrid classifier AAO GMM with PFCM feature outperforms than other classifiers and attained an accuracy of 99.03 % with MCC of 0.90

This paper focuses on parametric model order reduction (PMOR) of guided ultrasonic wave propagation and its interaction with damage in a fiber metal laminate (FML). Structural health monitoring in FML seeks to detect, localize and characterize the damage with high accuracy and minimal use of sensors. This can be achieved by the inverse problem analysis approach which employs the signal measurement data recorded by the embedded sensors in the structure. The inverse analysis requires to solve the forward simulation of the underlying system several thousand times. These simulations are often exorbitantly expensive and triggered the need for improving their computational efficiency. A PMOR approach hinged on the proper orthogonal decomposition method is presented in this paper. An adaptive parameter sampling technique is established with the aid of a surrogate model to efficiently update the reduced-order basis in a greedy fashion. A numerical experiment is conducted to illustrate the parametric training of the reduced-order model. The results show that the reduced-order solution based on the PMOR approach is accurately complying with that of the high fidelity solution.

Ultrasonic measurements are used in civil engineering for structural health monitoring of concrete infrastructures. The late portion of the ultrasonic wavefield, the coda, is sensitive to small changes in the elastic moduli of the material. Coda Wave Interferometry (CWI) correlates these small changes in the coda with the wavefield recorded in intact, or unperturbed, concrete specimen to reveal the amount of velocity change that occurred. CWI has the potential to detect localised damages and global velocity reductions alike. In this study, the sensitivity of CWI to different types of concrete mesostructures and their damage levels is investigated numerically. Realistic numerical concrete models of concrete specimen are generated and damage evolution is simulated using the discrete element method. In the virtual concrete lab, the simulated ultrasonic wavefield is propagated from one transducer using a realistic source signal and recorded at a second transducer. Different damage scenarios reveal a different slope in the decorrelation of waveforms with the observed reduction in velocities in the material. Finally, the impact and possible generalizations of the findings are discussed and recommendations are given for a potential application of CWI in concrete at structural scale.

Biological micro-dissection has a wide range of applications in the field of molecular pathology. The current laser-assisted dissection technology is expensive, and laser radiation can lead to sample contamination. As an economical and pollution-free micro-dissection method, piezoelectric ultrasonic micro-dissection has a wide application prospect. However, the performance of the current piezoelectric ultrasonic micro-dissection technology is unsatisfactory. In this paper, a novel piezoelectric ultrasonic micro-dissection device based on a flexure mechanism is proposed in order to solve the problems of low dissecting precision and excessive wear of the dissecting needle caused by the harmful lateral vibration of the current piezoelectric ultrasonic micro-dissection device. By analyzing the flexibility of flexure hinge, the type of flexure beam and the optimal design parameters are determined. Through comparing the harmonic response simulation analysis of the micro-dissection device based on a flexure mechanism and the traditional micro-dissection device without the flexure mechanism, the newly designed micro-dissection device achieves the best vibration effect when the driving frequency is 28kHz, compared with the traditional micro-dissection device, the lateral vibration suppression effect is improved by 68%. Then, based on the 3D printing technology, a prototype of a novel micro-dissection device was produced, and its performance was tested. It was found that the flexure mechanism did indeed suppress the lateral vibration of the needle tip. Finally, the experiments of 5μm thick paraffin-embedded rat liver sections were carried out, and the effects of different dissecting parameters on the dissecting effect were analyzed, and the optimal dissecting parameters were obtained. By comparing the dissecting effects of the tissue sample and the wear condition of the needle tip between the novel micro-dissection device and the traditional micro-dissection device under their optimal dissecting parameters, it is proved that the suppression of harmful lateral vibration not only significantly improves the dissecting effect, but also improves the service life and durability of the dissecting needle, which is beneficial to reduce the equipment costs.

Continuous ultrasonic in-situ monitoring for industrial applications is difficult owing to the high operating temperatures in industrial fields. It is expected that ultrasonic transducers consisting of CaBi4Ti4O15(CBT)/Pb(Zr,Ti)O3(PZT) sol-gel composite could be one solution for ultrasonic nondestructive testing (NDT) above 500 C because no couplant is required and CBT has a high Curie temperature. To verify the high temperature durability, CBT/PZT sol-gel composite films were fabricated on titanium substrates by spray coating, and the CBT/PZT samples were tested in a furnace at various temperatures. Reflected echoes with a high signal-to-noise ratio were observed up to 600 C. A thermal cycle test was conducted from room temperature to 600 C, and no significant deterioration was found after the second thermal cycle. To investigate the long-term high-temperature durability, a CBT/PZT ultrasonic transducer was tested in the furnace at 600 °C for 36 h. Ultrasonic responses were recorded every 3 h, and the sensitivity and signal-to-noise ratio were stable throughout the experiment.

This study investigates the long-term stability of the Suomi National Polar-orbiting Partnership (S-NPP) Visible Infrared Imaging Radiometer Suite (VIIRS) moderate-resolution Thermal Emissive Bands (M TEBs; M12 – M16) covering a period from February 2012 to August 2020. It also assesses inter-sensor consistency of the VIIRS M TEBs among three satellites-S-NPP, NOAA-20, and NOAA-21 over eight months spanning from March 18 to November 30, 2023. The field of interesting is limited to the ocean surface between 60°S and 60°N, specifically under clear-sky conditions. Taking radiative transfer modeling (RTM) as the transfer reference, we employed the Community Radiative Transfer Model (CRTM) to simulate VIIRS TEB brightness temperature (BTs), incorporating European Centre for Medium-range Weather Forecasts (ECMWF) reanalysis data as inputs. Our results reveal two key findings. Firstly, the reprocessed S-NPP VIIRS TEBs exhibit a robust long-term stability, as demonstrated through analyses of the observation minus background BT differences (O-B ∆BTs) between VIIRS measurements (O) and CRTM simulations (B). The drifts of the O-B BT differences are consistently less than 0.105 K/Decade across all S-NPP VIIRS M TEB bands. Notably, observations from VIIRS M14 and M16 stand out with drifts well within 0.04 K/Decade, reinforcing their exceptional reliability for climate change studies. Secondly, excellent inter-sensor consistency among these three VIIRS instruments is confirmed through the double-difference analysis method (O-O). This method relies on the O-B BT differences obtained from daily data. The mean inter-VIIRS O-O BT differences remain within 0.08 K for all M TEBs, except for M13. Even in the case of M13, the O-O BT differences between NOAA-21 and NOAA-20/S-NPP have values of 0.312 K and 0.234 K, respectively, which are comparable to the 0.2 K difference between some TEBs among VIIRS and MODIS. These disparities are primarily attributed to the significant differences in the Spectral Response Function (SRF) of NOAA-21 compared to NOAA-20 and S-NPP. Our study confirms the RTM-based TEB quality evaluation method’s versatility and effectiveness in assessing long-term sensor stability and inter-sensor consistency. The double-difference approach effectively mitigates uncertainties and biases inherent to CRTM simulations, establishing itself a robust mechanism for assessing inter-sensor consistency. In addition, we’ve observed that, except for M13, M12 always exhibits larger spatial variations of O-O BT differences with greater uncertainties compared to the other M TEBs. The influence of solar contribution through sea surface reflection on the Top of Atmosphere (TOA) radiance measurements during daytime in M12 should not be underestimated.

In this paper, a resonant system that produces a movement of low amplitude and ultrasonic frequency is used to achieve the vibration assistance in a ball-burnishing process. A full vibration characterization of this process performed in a lathe was done. It is carried out by a new tool designed in the research group of the authors. Its purpose is to demonstrate that the machine and the tool do not have any resonance problem during the process and to prevent possible failures. The analysis of this dynamic behaviour permits to validate the suitability of the tool when it is anchored to a numerical control lathe. This is very important for its future industrial implementation. It is also intended to confirm that the system adequately transmits vibrations through the material. To do this, a methodology to validate the dynamic tool behaviour was developed. Several techniques that combine the usual and ultrasonic vibration ranges through static and dynamic measurements were merged: vibration and acoustic emission measurements. An operational deflection shape (ODS) exercise has been also performed. Results show the suitability of the tool used to transmit the assistance vibrations, and that no damage is produced in the material in any case.

Nymphaea lotus L. is the medicinal plant that has long been used as food, cosmetic and traditional medicines in Africa and Asia since the ancient time. Its flavonoids and other interesting phytochemical compounds from rhizome, leaf, and the whole flowers have been reported in the previous published researches. However, stamens, which are essential for reproductive functions, may also represent new alternative sources of potential antioxidant flavonoids as investigated in this study. The innovative green chemistry method i.e. ultrasound-assisted extraction (USAE) as well as macroporous resin (MPR) purification procedure were employed in this current research. The optimal ultrasound-assisted extraction condition is 90 % (v/v) aqEtOH with 34.65 khz ultrasonic frequency and 46 minutes of extraction time. Comparing with heat reflux extraction (HRE) conventional method, the significant gain of 1.35 total flavonoids content was obtained using optimized USAE conditions, jumping to 2.80 when this USAE associated with MPR purification. Not only in vitro cell free antioxidant activity of N. lotus stamen extracts, but also in cellulo antioxidant investigation using yeast model showed the same trend to indicate that the best antioxidant flavonoid can be found in USAE coupled with MPR purification. Moreover, the key antioxidant genes expression in yeast model such as SIR2 and SOD2 were also expressed at the highest level in yeast cell treated with the extract from USAE together with MPR purification. Consequently, it can be seen that the USAE combined with MPR purification can help to enhance the flavonoids antioxidant potential of the stamens extract from this medicinal species.

We report a detailed investigation of vibrational modes, structure, and dynamics of glutathione (GSH) solutions using ultrasonic relaxation spectroscopy, FT-IR vibrational spectroscopy and electronic absorption measurements. The experimental data were analyzed in view of density functional theory (DFT) and molecular docking calculations. Three distinct Debye-type relaxation processes are resolved in the acoustic spectra, which are assigned to conformational changes between GSH conformers, self-association of GSH, and protonation processes. The standard volume changes for each process were estimated both experimentally and theoretically revealing a close resemblance among them. The higher the effect of the relaxation process in the structure, the greater the induced volume changes. From the temperature dependence of specific acoustic parameters, the thermodynamic characteristics of each process were determined. The experimental FT-IR spectra were compared with the corresponding theoretically predicted vibrational spectra revealing that the GSH dimers and extended conformers dominate the structure of GSH solutions in the high concentration region. The absorption spectra in the ultraviolet region confirmed the gradual aggregation mechanism that takes place in the aqueous GSH solutions. The results of the present study were discussed and analyzed in the framework of the current phenomenological status of the field.

This paper describes the design and implementation of an ultrasonic non-contact air-coupled technique (UNCACT) using antisymmetric Lamb waves (ALW) for NDT assessment in novel composite sandwich plates of the car body shell. This technique is complemented with a C-Scan image implementation using this kind of guided waves. The finite element method using Comsol 6.1 is developed for the interpretation of the several wave modes presented in the experiments, including the ALW mode. The phase velocity method (PVM) is applied for the verification of the ALW mode in the portion of the RF signal necessary in the C-Scan image.

The process of ultrasonic atomization involves a series of dynamic/topological deformations of free surface, though not always, of a bulk liquid (initially) below the air. This study focuses on such dynamic interfacial alterations realized by changing some acousto-related operating conditions, including ultrasound excitation frequency, acoustic strength or input power density, and the presence/absence of a “stabilizing” nozzle. High-speed, high-resolution imaging made it possible to qualitatively identify four representative transitions/demarcations: 1) the onset of a protrusion on otherwise flat free surface; 2) the appearance of undulation along the growing protuberance; 3) the triggering of emanating beads fountain out of this foundation-like region; and 4) the induction of droplets bursting and/or mist spreading. Quantitatively examined were the two-parameters specifications—on the degrees as well as induction—of the periodicity in the protrusion-surface and beads-fountain oscillations, detected over wider ranges of driving/excitation frequency (0.43–3.0 MHz) and input power density (0.5–10 W/cm2) applied to the ultrasound transducer of flat surface on which the nozzle was mounted or not. The resulting time sequence of images processed for the extended operating ranges, regarding the fountain structure pertaining in particular to recurring beads, confirms the wave-associated nature, i.e., their size “scalability” to the ultrasound wavelength, predictable from the traveling wave relationship. The thresholds in acoustic conditions for each of the four transition states of the fountain structure have been identified—notably, the onset of plausible “bifurcation” in the chain-beads diameter below a critical excitation frequency.

Numerical methods, including machine learning methods, are now actively used in the applications related to guided wave propagation. The method proposed in this study for material properties characterization is based on the algorithm of the clustering of multivariate data series obtained as a result of the application of the matrix pencil method to the experimental data. In the proposed technique, multi-objective optimization is employed to improve the accuracy of particular parameter identification. At the first stage, the computationally efficient method based on the calculation of the Fourier transform of Green's matrix is employed iteratively and the obtained solution is used for the filter construction with decreasing bandwidth, which allows us to obtain nearly noise-free classified data (with mode separation). The filter provides data separation between all guided waves in a natural way, which is needed at the second stage, where the slower method based on the minimization of the slowness residuals is applied to the data. The method might be applied for material properties identification in plates with thin coatings/interlayers, multi-layered anisotropic laminates etc.

Excitation of the acoustic field leading to the Blaha effect affects the plasticity of the material significantly in ultrasonic vibration-assisted forming. In a micro-forming field, the effects are more significant in the deformation in surface of materials [1]-[3], in which reduction of the surface roughness based on the increasing of plastic deformation of surface asperity was effective [4]. On the other hand, the effect on deformation behavior of the bulk region indicted reduction in the yield stress of materials, and not only acoustic effect [5], but also impact effect is found to generate a large amount of dislocation and produce plastic deformation [6][7]. However, the effect on the bulk is more significant as that on the surface. Differences in the effect on the surface and the bulk are not clarified. In this study, the mechanism of the deformation in the surface of the material with ultrasonic vibration assistance is investigated and compared with that in the bulk. Forging tests using a newly developed ultrasonic vibrator were carried out on pure Cu foils with various process conditions. The longitudinal vibration frequency of the ultrasonic transducer is 60∓2kHz, and the vibration amplitude is in an adjustable range of 0~10μm. Forging test was carried out at different initial stress, specimen size and amplitude. The difference in acoustic softening and impact effects on the surface and the bulk was discussed.

Ultrasonic imaging & NDE applications can greatly improve their signal-to-noise ratios (SNR) by driving each transducer (composing piezoelectric arrays) with a spike giving pulsed power of k-Watts, repetitively at a PRF = 5000 spikes/s, by using a HV capacitive-discharge generator. However very-high levels, of pulsed intensities (3-10 A) and voltages (300-700 V) must be considered for a rigorous spike modeling. Even though the consumed "average" power will be small, the intensity through each transducer achieves several amperes, so the pulsed powers delivered by each HV generator can attain levels higher than in CW high-power ultrasonic applications: e.g., up to 5 kW / spike. This is concluded here from a transient modeling of the loaded generator. Then, unforeseen phenomena rise: intense brief pulses of driving power & emitted force in transducers, and non-linearities in driver semiconductors, because their characteristic curves only include linear ranges. But fortunately, piezoelectric devices working in this intense regime do not show serious heating problems, because the average power remains being moderate. Intensity, power and voltage, driving a broadband transducer from a HV capacitive pulser, are calculated to drastically improve (in ≅ 40 dB) the ultrasonic net dynamic range available, with emitted forces ≅ 250 Newtons pp and E/R received pulses of 70 V pp.

We used an ultrasensitive, broadband optomechanical ultrasound sensor to study the acoustic signals produced by pressurized nitrogen escaping from a variety of small syringes. Harmonically related jet tones extending into the MHz region were observed for a certain range of flow (i.e., Reynolds number), in qualitative agreement with historical studies on gas jets emitted from pipes/orifices of much larger dimensions. For higher turbulent flow rates, we observed broadband ultrasonic emission in the ~ 0 – 5 MHz range, likely limited on the upper end by attenuation in air. These observations are made possible by the broadband, ultrasensitive response (for air-coupled ultrasound) of our optomechanical devices. Aside from their theoretical interest, our results could have practical implications for the non-contact monitoring and detection of early-stage leaks in pressured fluid systems.

This paper aims to study the surface homogenization and integrity of Ti-6Al-4V alloy by longitudinal-torsional coupled ultrasonic vibration assisted ball-end milling. A method of continuous processing between the flat surface and freeform surface connection is proposed by using ultrasonic vibration assisted ball-end precision milling, during this process, it is not necessary to exchange the cutting tool. The way has been explored for changing the homogenization of surface on Ti-6Al-4V by ultrasonic vibration-assisted milling (UVAM). Cutting experiments employing three parameters, cutting speed, feed rate and depth of cut and two types of machining forms using ball-end milling with UVAM and conventional milling (CM) respectively. The high frequency cutting force, finished surface roughness, topography and residual stresses on the surface and tool wear have been measured by advanced instruments. Particularly, adopting the high frequency cutting force measurement system, it is concluded cutting force in ball-end milling decreased significantly using UVAM as against CM. Moreover, the surface roughness by UVAM with ball-end milling is much better than the CM at a high cutting speed. However, an opposite trend is observed at a low cutting speed. Especially, there is a steep decrease from Ra 0.828 μm average value at 4000 rpm to Ra 0.129 μm average value at 5000 rpm. At the same time, the homogenization of surface roughness and residual stresses decrease significantly in UVAM as compared to which in CM when taking the transversal-longitudinal ratio into consideration. Cutting experiments and measuring results are demonstrated the validity and feasibility of UVAM with ball-end milling, and this method enjoys significant advantages compared to CM process.

Wireless Sensor Networks (WSN) is designed to collect information across a large number of limited battery sensor nodes. Therefore, it is important to minimize the energy consumption of each node, which leads to the extension of the network life. Our goal is to design an intelligent WSN that collects as much information as possible to process it intelligently. To achieve this goal, an agent has been migrated to each node in order to process the information and to cooperate with these neighboring nodes while Mobile Agents (MA) can be used to reduce information between nodes and send those to the base station (Sink). This work proposes to use communication architecture for wireless sensor networks based on the Multi Agent System (MAS) to ensure optimal information collection. The collaboration of these agents generates a simple message that summarizes the important information in order to transmit it by a mobile agent. To reduce the size of the MA, the nodes of the network have been grouped into sector. As for each MA, we have established an optimal itinerary, consuming a minimum amount of energy with the data aggregation efficiency in a minimum time. Successive simulations in large scale wireless sensor networks through the SINALGO simulator show the performance of our proposal, in terms of energy consumption and package delivery rate.

This paper address the development of a new technic in the sleep analysis domain. Sleep is defined as a periodic physiological state during which vigilance is suspended and reactivity to external stimulations diminished. We sleep on average between six and nine hours per night and our sleep is composed of four to six cycles of about 90-minutes each. Each of these cycles is composed of a succession of several stages of sleep, more or less deep. The analysis of sleep is usually done using a polysomnography. This examination consists of recording, among other things, electrical cerebral activity by electroencephalography (EEG), ocular movements by electrooculography (EOG) and chin muscle tone by electromyography (EMG). The recording is done mostly in a hospital, more specifically in a service for monitoring the pathologies related to sleep. The readings are then interpreted manually by an expert to generate a hypnogram, a curve showing the succession of sleep stages during the night in 30-second epochs. The proposed method is based on the follow-up of the thermal signature that makes it possible to classify the activity into three classes: "awakening", "calm sleep" and "agitated sleep". The contribution of this non-invasive method is part of the screening of sleep disorders, to be validated by a more complete analysis of the sleep. The measure provided by this new system, based on temperature monitoring (patient and ambient), aims to be integrated into the tele-medicine platform developed within the framework of the Smart-EEG project by the SYEL - SYstèmes ELectroniques team. Analysis of the data collected during the first surveys carried out with this method showed a correlation between thermal signature and activity during sleep. The advantage of this method lies in its simplicity and the possibility of carrying out measurements of activity during sleep and without direct contact with the patient at home or hospitals.

In recent years, the integration of sensors in agriculture has emerged as a pivotal catalyst for transforming conventional farming practices into precision agriculture. Sensor application is impacting the everyday objects that enhance human life. In this special issue, the main objective was to address recent advantages of sensor application in agriculture covering a wide range of topics in this field. This provides overview of diverse application of sensors in agriculture, highlighting their role in enhancing productivity, sustainability, and resource management. sensors are instrumental in monitoring various agriculture parameter such as soil condition, weather, crop health and livestock wellbeing. By collecting real-time data and providing valuable insight, sensors enable precision farming, optimize resource allocation, and minimize environmental impacts. we have to explore the key sensor types used in agriculture, their applications, benefits, and future prospects, emphasizing their crucial roles in the modernization of agriculture and global quest for food security and crop production.

This paper describes the optimal design of a miniature fiber-optic linear displacement sensor. It is characterized by its ability to measure displacements along a millimetric range with sub-micrometric resolution. The sensor consists of a triangular reflective grating and two fiber-optic probes. The measurement principle of the sensor is presented. The design of the sensor's triangular grating has been geometrically optimized by considering the step angle of the grating to enhance the sensor's resolution. The optimization method revealed a global optimum at which the highest resolution is obtained

Sensor enabled big data and Artificial Intelligence platforms has the potential to address global socio-economic trends related to the livestock production sector through advances in the digitization of precision livestock farming. The increased interest in animal welfare, the likely reduction in the number of animals in relation to population growth in the coming decade and the growing demand for animal proteins pose an acute challenge to prioritizing animal welfare on the one hand while maximizing the efficiency of production systems on the other. To stimulate a sustainable, digital, and resilient recovery of the agricultural and livestock industrial sector, there is an urgent need for testing and develop new ideas and products such as wearable sensors. By validating and demonstrating a fully functional wearable sensor prototype within an operational environment on the livestock farm that includes a miniaturized animal-borne biosensor and an artificial intelligence (AI) based data acquisition and processing platform, the unmet current needs can be fulfilled. The expected quantifiable results from wearable biosensors will demonstrate that the digitization technology can perform acceptably within the performance parameters specified by the agricultural sector and under operational conditions, to measurably improve livestock productivity and health. There is a need for a multimodal, digitized, automated biosensor and health monitoring platform containing AI algorithms for optimized stress and disease prediction in farm animals. An experimental development of non-invasive wearable and wireless physiological sensor networks that can be deployed in agricultural environments would allow for real-time extraction and integration of physiological data and display on decision support dashboards for livestock workers. By testing the effectiveness of the system in generating meaningful longitudinal data for further research into physiological and behavioral characteristics of farm animals, novel insights about animal welfare can be developed. The successful implementation of the digital wearable sensor networks would provide actionable real-time information on animal health status and can be deployed directly on the livestock farm, which will strengthen the green and digital recovery of the economy due to the significant innovation potential. Continuous monitoring of animal health and physiological functioning promotes more environmentally and socially acceptable developmental pathways. Once demonstrated, the portable animal health monitoring platform will close a critical gap in digitized livestock farming and position the agricultural industry as a frontrunner in the sector of farm animal monitoring and measurement systems. The multimodal wearable sensor-driven AI approach is expected to significantly improve the effectiveness of livestock decision support systems and the selection of resilient animals for the next generation and provide predictive data for end-users in livestock farming.

Smartwatches provide technology-based assessments in Parkinson’s disease (PD). We present results for sensor validation and disease classification via Machine Learning (ML). A comparison setup was designed with two different series of Apple smartwatches, one Nanometrics seismometer and a high-precision shaker to measure tremor-like amplitudes and frequencies. Clinical smartwatch measurements were acquired from a prospective study including 450 participants with PD, differential diagnoses (DD) and healthy participants. All participants wore two smartwatches and within a 15-min examination. Symptoms and medical history were captured on the paired smartphone. A broad range of different ML classifiers were cross-validated. Amplitude and frequency differences between smartwatches and the seismometer were under the level of clinical significance. The most advanced task of distinguishing PD vs DD was evaluated with 74,1% balanced accuracy, 86,5% precision and 90,5% recall by Multilayer Perceptrons. Deep Learning architectures significantly underperformed in all classification tasks. Smartwatches are capable of capturing subtle-tremor signs with low noise. This study provided the largest PD sample size of two-hand smartwatch measurements and our preliminary ML-evaluation shows that such a system provides powerful means for diagnosis classification and new digital biomarkers but it remains challenging for distinguishing similar disorders.

In this work, an embroidered textile moisture sensor is presented. The sensor is based on a capacitive interdigitated structure embroidered on a cotton substrate with an embroidery conductor yarn composed by 99% pure silver plated nylon yarn 140/17 dtex. In order to evaluate the sensor sensitivity, the impedance of the sensor has been measured by means of a LCR meter from 20 Hz to 20 kHz on a climatic chamber with a sweep of the relative humidity from 25% to 65% at 20 ºC. The experimental results show a clear and controllable dependence of the sensor impedance with the relative humidity. Moreover, the reproducibility of the sensor performance subject to the manufacturing process variability and washing process is also evaluated. The results show that the manufacturing variability introduce a moisture measurement error up to 4%. The washing process impact on the sensor behavior after applying the first washing cycle implies a sensitivity reduction higher than 14%. Despite these effect, the textile sensor keeps its functionality and can be reused in standard conditions. Therefore, these properties point out the usefulness of the proposed sensor to develop wearable applications on health and fitness scope including the user needs to have a life cycle longer than one-time use