To develop a lower-cost, excellent performance, and environmentally friendly phe-nol-formaldehyde (PF) resin, soybean meal was used to modify PF resin, and soybean meal-phenol-formaldehyde (SMPF) resins were prepared. Their physicochemical properties and curing performance were investigated, showing that SMPF resins have higher curing tempera-tures than PF resin. The Fourier transform infrared spectroscopy (FTIR) results indicated that the cross-linking reaction occurred between the amino groups of soybean protein and the hy-droxymethyl phenol. Moreover, with the addition of soybean meal, the viscosity of SMPF in-creased while the gel time decreased. It is worth mentioning that SMPF-2 resin has favorable viscosity, short gel time, low curing temperature (135.78 °C), and high water resistance and bonding strength (1.01 MPa). Finally, all the plywoods bonded with SMPF resins have good water resistance and bonding strength, which could meet the Standard (GB/T 17657-2013, type I) for plywood. The optimized SMPF resins showed the potential application to replace part of PF resin in the wood industry.

Novolac phenol-formaldehyde resins have gained extensive commercial utilization across diverse applications due to their exceptional mechanical, thermal, and chemical resistance properties. In this investigation, we successfully synthesized a traditional novolac, and a biobased novolac phenol-formaldehyde resin by partially substituting phenol with a bio-oil obtained from the organic phase resulting from the fast pyrolysis of pinewood biomass. Despite extensive investigations into the curing behavior of novolac resins crosslinked with hexamethylenetetramine (HMTA) through numerous model-fitting cure kinetic studies, a comprehensive model for predicting the crosslinking of bio-based phenol-formaldehyde resins in the presence of HMTA has not yet been studied. The primary objective of this research was to compare and apply several commonly used kinetic models to predict the degree of curing and cure rate of the synthesized resins, using DSC dynamic measurements. Our results demonstrated that the autocatalytic model exhibited excellent fitting for the traditional novolac resin and HMTA mixture, while the Kamal model showed better fitting with the experimental data obtained for the bio-based phenol-formaldehyde resin and HMTA system. In addition, the results evidenced a significant drop in the curing temperature by partially replacing phenol with bio-oil. Additionally, the results revealed a notable reduction in curing temperature when phenol was partially substituted with bio-oil. This substitution not only offers environmental benefits but also promotes energy efficiency and enhances production safety. The data collected in this study is pivotal for our subsequent research endeavors, which aim to develop environmentally sustainable materials optimized for use in 3D printing manufacturing processes.

Urea cycle disorders (UCDs) are common inborn errors of metabolism, with an incidence of one in 30,000 births. They are caused by deficiencies in any of six enzymes and two carrier proteins, the most common being Ornithine Transcarbamylase Deficiency (OTCD). OTCD results in impairment to excrete nitrogen, causing toxic buildup of ammonia with resultant encephalopathy. Hyperammonemia (HA) induces the conversion of glutamate to glutamine in the brain. Excess glutamine in the brain causes osmotic changes cerebral edema, changes in astrocyte morphology, and cell death. Acute symptoms of HA include vomiting, hyperventilation, seizures, and irritability. Long-term neurological changes include deficits in working memory and executive function. To date, there are no predictors of prognosis of infants with neonatal onset OTCD outside of plasma ammonia level at presentation and duration of hyperammonemic coma. We provide a comprehensive analysis of a 16-year-old male with neonatal onset of OTCD as an example of how brain biomarkers may be useful to monitor disease course and outcome. This male presented at 8 days post natal with plasma ammonia and glutamine of 677 and 4024 micromol/L and had a missense mutation in Exon 4 (p.R129H). Treatment included protein restriction, sodium benzoate, and citrulline, arginine, and iron. He suffered recurrent acute hyperammonemic episodes despite compliance, triggered by infections or catabolic stressors. We discuss the long-term effects of the hyperammonemic episodes by following MRI based disease biomarkers.

Hybrid materials are a recent addition in the field of Restorative Dentistry for computer-assisted design/ computer-assisted manufacturing (CAD/CAM) indirect restorations. The long–term clinical success of modern dental restorative materials follows a multifactorial pattern. Among the characteristics, affecting the longevity of a restoration, mechanical properties and physicο – chemical interactions are of utmost importance. While numerous researchers constantly evaluate the mechanical properties, the biological background of resin–based CAD/CAM biomaterials is scarcely investigated and, therefore, less described in the literature. This review aims to analyze the biofilm formation on the surfaces of novel hybrid, resin–based CAD/CAM materials and evaluate the methodological protocols followed to assess microbial growth. It is demonstrated that the surface structure, the composition and the finishing and polishing procedures on the surface of a dental restorative material influence the initial bacterial adhesion; however most studies focus on in vitro protocols, whereas in vivo and/or in situ research of microbiomics in CAD/CAM restorative materials is lacking, obstructing in that manner the accurate understanding of the bioadhesion phenomenon in the oral cavity.

Generally, mineral fillers are added to thermoplastic polymers to reduce cost and improve performance. However, properly selected mineral fillers can also improve thermal conductivity and deformation behavior, shrinkage, impact strength, dimensional stability, and molding cycle time in thermoset polymers. This study focused on the preparation and microscopic and spectroscopic characterization of various hybrid composites using pumice as primary filler and gypsum, kaolin and hollow glass sphere as secondary fillers, as well as examining some of their mechanical properties and thermal conductivities. For this, first of all, surface modification of the clay was carried out by intercalation method from solution using raw Montmorillonite, cationic surfactant and long chain hydrocarbon material, and then organo-clay melamine formaldehyde nanocomposite was prepared by in situ synthesis using organo clay and melamine formaldehyde pre-polymer. Finally, non-ionic surfactant, foaming agent and glycerin were added to the prepared nano-composite at approximately 90°C, mixed mechanically and then pumice was added. The processes at this stage were repeated while preparing hybrid composites with pumice and other mineral additives. For curing and molding, the composite was first subjected to microwave irradiation for 5 minutes followed by thermal treatment at 140°C for 60 min. Fourier transform infrared spectroscopy (FTIR), X-ray powder diffraction (XRD) spectra and Scanning electron microscope (SEM) and High resolution transmission electron microscope (HRTEM) images were taken for morphological and textural characterization for raw clay (MMT), organo clay (OMMT) and pure polymer with prepared hybrid composites. In addition, some mechanical properties such as bending strength, elasticity modulus and screw holding resistance, as well as thermal conductivity coefficients of the hybrid composites were determined according to the relevant standards and the obtained results were evaluated. Spectroscopic and microscopic analyzes have shown that effective adhesion interactions occur between polymer-clay nanocomposite particles and filler grains, thus resulting in textural arrangements with different properties. Mechanical and thermal conductivity test results showed that melamine formaldehyde-organo-clay nano composite foam and hybrid composite containing hollow glass sphere are highly qualified materials in terms of thermal insulation and mechanical strength.

In this study, the impact of the addition of high-aspect-ratio nano-ettringite to photocurable epoxy acrylate resin was explored, with a specific focus on the changes observed in viscosity, shrinkage, tensile strength, and elongation at the break of composites formed. Herein, the nano-ettringite samples were modified using KH-570. The 3 wt% or 6 wt% KH-570-modified and unmodified nano-ettringite were dispersed into the resin by ultrasonic treatment in conjunction with mechanical stirring. The grafting effects of nano-ettringite onto KH-570 were analyzed through scanning electron microscopy (SEM), X-ray diffraction (XRD), thermogravimetric (TG) analysis, and Fourier transform infrared spectroscopy (FTIR). The results demonstrate that increased dosages of unmodified and modified nano-ettringite led to increased viscosity of the composite while reducing shrinkage. At the same dosage, the photocurable resin with modified nano-ettringite demonstrated a lower shrinkage and a higher tensile strength. Notably, when the amount of modified nano-ettringite was 3 wt%, the highest tensile strength of the composite was 64.61 MPa, presenting a 72.57% increase compared to the blank sample. Furthermore, the incorporation of modified nano-ettringite as a filler provides a new perspective for improving the performance of photocurable epoxy acrylate resin composites.

The objective of this study was to detail the monomer composition of resin-based dental materials sold in the market in 2023 and to evaluate the proportion of BPA derivatives in relation with their applications. A search on manufacturers’ websites was performed to reference resin-based dental materials currently on the market. Their monomer composition was determined from material safety data sheets and completed with a search on PubMed database. Among the 543 material compositions exploitable, 382 (70.3%) contained BPA derivatives. Among them, 56.2% contained BisGMA, 28% BisEMA, the most frequently reported. A total of 59 monomers of which 6 BPA-derivatives were found. 309 materials (56.9%) contained UDMA and 292 (53.8%) TEGDMA. Less than one third of materials identified contained no BPA derivatives. These proportions vary a lot depending on their applications with materials dedicated to dental care of young populations containing the highest proportions of BPA-derivatives monomers. The long-term effects on human health of the different monomers identified including BPA-derivatives monomers is a source of concern. For children and pregnant or lactating women arises the question to take a precautionary principle and avoid the use of resin-based dental materials likely to release BPA by opting for alternative materials.

The objective of this study was to evaluate the efficacy of fungal treatment (Pleurotus ostreatus) of urea-treated rice stubble on growth performance in slow-growing goats. Eighteen crossbred Thai native x Anglo-Nubian male goats (average body weight: 20.4 ± 2.0 kg) were randomly assigned to three experimental total mixed rations containing 35% rice stubble (RS) that was either untreated (URS), urea treated (UTRS) or treated with urea and fungi (UFTRS). URS and UTRS were cultivated and harvested from aseptically fungal spawn, incubated at 25-30 °C for 25 days. Indicators of growth performance were monitored and faeces were collected quantitatively to assess nutrient digestibility, during a 12-week feeding trial. All goats remained healthy throughout experiment. The goats fed UFTRS had a lower feed conversion ratio (kg feed/kg growth) compared to goats fed URS or UTRS. Compared to URS, dietary UFTRS increased nutrient digestibility of slow-growing goats, such as OM (+8.5%), CP (+5.5%), NDF (+39.2%), and ADF (+27.4%). Likewise, dietary UFTRS tended to increase rumen ammonia concentrations but rumen pH and volatile fatty acids were not affected by UFTRS. In conclusion, the present study indicates that the fungal treatment of RS is an effective tool to improve the growth performance of slow-growing goats.

Air pollution is related to the development of people's livelihood. As one of the main pollutants in the air, formaldehyde affects people's physical and mental health. In order to remove formaldehyde and better protect the health of residents, it is very necessary to develop efficient adsorption materials. In this study, a cellulose composite aerogel Microcrystalline Cellulose/ N-(2- aminoethyl) -3- aminopropyl methyl dimethoxysilane (MCC/APMDS) modified by APMDS was explored. The pore volume and specific surface area of the modified aerogel decreased, the average pore diameter increased, and the adsorption capacity of formaldehyde was stronger. The adsorption experiment shows that the sample prepared under the conditions of APMDS dosage of 6 wt%, reaction time of 4 h and reaction temperature of 90℃ has the largest average pore size (14.56 nm) and the largest formaldehyde adsorption capacity (9.52 mg/g). The excellent adsorption of the composite aerogel is due to high porosity and rich active amino groups on the surface. This study provides valuable information for the preparation of adsorption materials with high formaldehyde adsorption capacity for air purification.

Preventing the occurrence of secondary caries serves as one of the significant issues in dental clinic, thus make it indispensable to improving the properties of conventional composite resin (CR) by developing a novel CR. In present study, two groups of experimental CRs loaded with different contents of fluoride-doped nano-zirconia fillers (25 wt% and 50 wt%) were fabricated. The surface topography, mechanical performance, fluoride release, antibacterial effect, aging property and cytotoxicity of the experimental CRs were evaluated subsequently. A uniform distribution of the F-zirconia fillers over the whole surface of resin matrix could be observed. The experimental CRs showed continuous fluoride release within 28 days, which was positively correlated with the content of F-zirconia fillers. Moreover, the amount of fluoride release increased in the acidic buffer. Addition of F-zirconia fillers could improve the color stability, wear resistance and microhardness of the experimental CRs, without reducing the flexure strength. Furtherly, the fluoride ions released continuously from the experimental CRs resulted in effective contact and antibacterial properties, while they showed no cytotoxicity. As a consequence, considerations can be made to employ this new kind of composite resin loaded with fluoride-doped nano-zirconia fillers to meet clinical requirements when the antimicrobial benefits are desired.

The aim of this study was to investigate the effect of laser irradiation to computer-aided de-sign/computer-aided fabrication (CAD/CAM) resin blocks coated with a silane coupling agent on the bond strength between the resin blocks and composite resin. The CAD/CAM resin blocks used in this study were Cerasmart 300 (GC) and Vita Enamic (Vita); they were cut into plates and then subjected to a series of treatments. After processing with a silane coupling agent, treatment with a semiconductor laser was performed at 3.0, 5.0, and 7.0 W, followed by the bonding procedures. The control group included those exposed to silane and bonded without laser application. After bonding, a mold with a simulated cavity was formed on the specimen and filled with flowable composite resin, and they were stored for 24 h or stressed by thermal cycling for subsequent testing that assessed the shear bond strength (n = 10). The results revealed that the bond strength was significantly enhanced by laser irradiation after applying a silane coupling agent, whereas significant effect was not detected between the materials. Particularly, 7 W laser irradiation had a significant effect on the bond strength between the composite resin and Cerasmart block after thermal cycling.

In this scientific research, thermally stable nickel nanoparticles were synthesized and characterized. Nickel nanoparticles were synthesized using phenol –formaldehyde by chemical method followed by calcination. The polymer metal complex was confirmed by FTIR and NMR. The spherical morphology of nickel nanoparticles confirmed by SEM. The crystallographic structure is confirmed by XRD and size of cobalt nanoparticles is 24.0 nm. The TGA analysis was performed over a range of 29-600OC. The TGA thermograph predicts mass decomposition of 11%, for nickel phenol-formaldehyde nanocomposite. The decomposition rate of composites is very low 2% weight loss per 100OC increment in temperature.

Hepatitis C virus (HCV) is an oncogenic virus that causes chronic liver disease in more than 80% of patients. During the last decade, efficient direct acting antivirals were introduced into clinical practice. However, clearance of the virus does not reduce risk of end-stage liver diseases to the level observed in patients that have never been infected. So, investigation of HCV pathogenesis is still warranted. Virus-induced changes in cell metabolism contribute to the development of HCV-associated liver pathologies. Here we studied the impact of the virus on the metabolism of polyamines and proline as well as on the urea cycle, which plays a crucial role in liver function. It was found that HCV strongly suppresses the expression of arginase, a key enzyme of the urea cycle, leading to accumulation of arginine and upregulates proline oxidase with a concomitant decrease in proline concentrations. Addition of exogenous proline moderately suppressed viral replication. HCV upregulated transcription but suppressed protein levels of polyamine-metabolizing enzymes. This resulted in a decrease in polyamine content in infected cells. Finally, compounds targeting polyamine metabolism demonstrated pronounced antiviral activity pointing to spermine and spermidine as compounds affecting HCV replication. These data expand our understanding of HCV’s imprint on cell metabolism.

Purpose: This study aimed to evaluate the nanomechanical properties and chemical composition of restorative materials and dental surfaces using different toothpastes. Methods: Enamel (n=60) and dentin (n=60) bovine blocks were obtained and restored using resin-modified glass ionomer cement (RMGIC, n=30) or composite resin (CR, n=30) to form the dentin adjacent to RMGIC (DRMGIC), enamel adjacent to RMGIC (ERMGIC), dentin adjacent to CR (DCR), and enamel adjacent to CR (ECR). After restoration, one hemiface of each specimen was coated with an acid-resistant varnish to create the control (C) and eroded (E) sides (erosion: 5 days, 4 × 2 min/day; 1% citric acid / abrasion: 2 × 15 s followed by immersion on slurries 2 min). Three toothpastes were used: without fluoride (WF; n=10), sodium fluoride (NaF; n=10), and stannous fluoride (SnF2; n=10). The specimens were analyzed for nanohardness (H), elastic modulus (Er), and chemical composition using energy-dispersive X-ray spectroscopy (EDS) and Raman microscopy. Data were analyzed using ANOVA two-way repeated measures and Tukey’s test (α = 0.05). Results: The NaF presented lower values of H for DRMGIC-C, with a statistical difference for WF (p < 0.05). SnF2 resulted in lower Er values for ERMGIC-E and RMGIC-E than WF and NaF (p < 0.05). WF showed lower calcium and phosphorus concentrations for DCR-E than other types of toothpastes (p < 0.05). Only stannous-based toothpaste damaged the elasticity of eroded glass ionomer restorations performed in enamel. Toothpastes with fluoride was capable for maintaining main chemical elements of dentin adjacent to restorative materials under challenge conditions.

Wasted Green tuff powder produced by cutting Towada stone is recycled as environmental cleaning material. The optimum temperature for green tuff powder calcination to reduce the hydroxyl radical produced in hydrogen peroxide decomposition with ultraviolet light (UV) and no light. The green tuff calcined at 800 °C shows the large decomposition rate of hydrogen peroxide with no UV light when measured by using ESR. With UV light, the optimum temperature for calcinating the green tuff powder in order to reduce hydroxyl radical is also 800 °C. Next, the powder calcined at 800 °C is used to produce the tile by compression and heating, and then the formaldehyde adsorption rate was measured. The green tuff powder calcined at 800 °C showed a high adsorption rate, similar to that of the activated carbon. The tiles formed at 40 MPa and heated st 1100 °C were the strongest and also adsorbed formaldehyde. The adsorbed formaldehyde on the green tuff tile and powder might have a possibility to decompose by photocatalytic.

In antimicrobial-peptide/protein engineering, understanding the peptide/protein’s adaptability to harsh environmental conditions such as urea, proteases, fluctuating temperatures, high salts provide enormous insight into the pharmacokinetics and pharmacodynamics of the engineered peptide/protein and its ability to survive the harsh internal environment of the human body such as the gut or the harsh external environment to which they are applied. A previous work in our laboratory demonstrated that our cloned Eɛ34 TSP showed potent antimicrobial activity against Salmonella newington, and more so, could prevent biofilm formation on decellularized tissue. In this work, the effects of urea-acid on the Eɛ34 stability is studied, and the results demonstrates that at lower pHs of 3 and 4 with urea the protein was denatured into monomeric species. However, the protein withstood urea denaturation above pH of 5 and thus remained as trimeric protein. The mechanism of denaturation of Eɛ34 TSP seems to show that urea denatures proteins by depleting hydrophobic core of the protein by directly binding to the amide units via hydrogen bonds. The results of our in-silico investigation determined that urea binds with Eɛ34 TSP with relative free energies range of -3.4 to -2.9 kcal/mol at the putative globular head binding domain of the protein. The urea molecules interacts with with the protein’s predicted hydrophobic core, thus, disrupting and exposing the shielded hydrophobic moieties of Eɛ34 TSP to the solvent. We further showed that after the unfolding of Eɛ34 TSP via urea-acid, renaturation of the protein to its native conformation was possible within few hours. This unique characteristic of refolding of Eɛ34 TSP which is similar to that of the P22 phage tailspike protein is of special interest to protein scientists and can also be exploited in antimicrobial-protein engineering.

In recent years, polyureas with dynamic hindered urea bonds (HUBs), as a class of promising biomedical polymers, have attracted attention as a benefit of their controlled hydrolytic property. The effect of the chemical structures on the properties of polyureas and their assemblies was rarely reported. In this study, four kinds of polyureas with different chemical groups have been synthesized, and the polyurea from cyclohexyl diisocyanate and tert-butyl diamine showed the fastest hydrolytic rate. The amphiphilic polyurea composed of hydrophobic cyclohexyl-tert-butyl polyurea and hydrophilic poly(ethylene glycol) was synthesized for controlled delivery of antitumor drug paclitaxel (PTX). The PTX-loaded PEGylated polyurea micelle more effectively entered into the murine breast cancer 4T1 cells and inhibited the corresponding tumor growth in vitro and in vivo. Therefore, the PEGylated polyurea with adjustable degradation might be a promising polymer matrix for drug delivery.

This study represents a significant stride in advancing furan chemistry, presenting the synthesis of high-molecular-weight polyfurfuryl alcohol (PFA) resin (Mw = 118,959 g/mol) from furfuryl alcohol (FA) using a co-catalytic system as against the conventional single-catalytic methods. The resulting PFA resin is fully characterised, and we conclude that it exhibits good shelf life and potential in diverse applications, serving as a standalone moulded material or contributing to composites, coatings, adhesives, and nanostructured carbons.

As one of toxic Volatile Organic Pollutant (TVOCs), formaldehyde has a toxic effect on microorganisms, and then inhibits the biochemical process of formaldehyde wastewater treatment. Therefore, the selective degradation of formaldehyde is of great significance to achieve formaldehyde wastewater high-efficiency and low-cost treatment. This study constructed a heterogeneous Fe-ZSM-5/H2O2 Fenton system for selective degradation to target compounds. By bonding Fe3+ onto the surface of ZSM-5 molecular sieve, Fe-ZSM-5 was prepared successfully. XRD, BET and FT-IR spectral studies shown the prepared Fe-ZSM-5 was mainly composed of micropores. The influences of different variables on formaldehyde selective heterogeneous Fenton degradation performance were studied. The 93.72% formaldehyde degradation and the 98.15% selectivity of formaldehyde compared with glucose had demonstrated in the optimized Fenton system after 360 min. Notably, the resultant selective Fenton oxidation system had a wide range of pH suitability from 3.0 to 10.0. Also, the Fe-ZSM-5 was used in 5 consecutive cycles, while the degradation efficiency of formaldehyde did not drop dramatically. Using reactive oxygen species scavengers, hydroxyl radical was the main active substance to degrade formaldehyde. Furthermore, the great degradation performance of this system to high concentration of formaldehyde was acquired, and the degrading efficiency was more than 95%.

Immobilization of enzymes is a good field of study to expand the life of enzyme in and lowering the cost of the chemical processes such as separation processes. Urease is an important enzyme with medical and industrial applications. The aim of the present study is to prepare an immobilized urease on a strong cation exchange resin (Amberlite IR120 -Na) and study of its activity and stability. We monitored the liberation of Na ions in the collected fractions and searching for protein in the fractions as an indicators of immobilization by ion exchange phenomenon. Sodium is measured using atomic absorption spectroscopy techniques, while protein tested by Bradford’s method. Immobilized urease activity was evaluated by salicylate-hypochlorite method. The results indicated a complete immobilization of urease enzyme on the resin surface with reserving 92% of the activity of free enzyme. The immobilized urease enzyme on resin showed good stability and it has a 62% of its activity after 154 days of storage at room temperature. It is concluded that a new immobilized urease enzyme system is prepared with good enzyme activity and stability.

The crosslinking behavior of polyethylene (PE) determines its exceptional performance and application. In this study, we investigated the crosslinking behaviors of different PE resins through model simulation and rheological methods. Specifically, the mathematical equation of "S" model was established for PE resin. According to this equation, the optimal maximum gel content for high-density polyethylene (HDPE) was found to be around 85%. Moreover, the maximum crosslinking degrees for different PE resins depended largely on their density and molecular weight. The melt viscosities before crosslinking in PE resins were highly influenced by their melt index. The higher melt indexes resulted in the lower storage moduli, improving melt processability during processing. In addition, the crosslinking rates of PE resins were strongly influenced by peroxide concentration, independent of PE resin structures. For high molecular weight and low-density PE resins, they exhibited decreased ti values, increased A0 values, and decreased k6 values. However, there were no noticeable variations in the values of k2 and phi among different PE resins. And all simulated modeling outcomes showed the remarkable consistency with the experimental rheological data. These findings are of utmost significance in the industrial manufacture of PE resin.

Nano-titanium has excellent corrosion resistance and can be widely used in the field of corrosion resistant coatings. This paper introduces nano-weight titanium modified phenolic resin coatings and their anti-corrosion properties to explore the principle of nano-titanium modification and the mechanism of anti-corrosion to further develop more advanced corrosion resistant coatings. The article uses scanning electron microscopy, Fourier transform infrared spectroscopy, Raman spectroscopy and UV-Vis spectrophotometer to characterise the morphology and structure of the nano-titanium modified phenolic resin coatings and to determine the corrosion resistance properties of the modified phenolic resin coatings. The results show that the 4% nano-titanium modified phenolic resin coating, nano-titanium powder and phenolic resin will maximize the dispersion and combination, and the structure is good; nano-titanium grafted on phenolic resin, the successful preparation of nano-titanium modified phenolic resin; modified nano-titanium added to improve the coating's ability of UV absorption. The corrosion resistance of the coating is much better than that of the unmodified phenolic resin coating.

Introduction: To indentify the most effective actors(authors, countries, and journals) about composite resin restorations in the period 2000-2020.Material and Methods: An electronis research was conducted in the Scopus database by selecting the words ‘composite resin’ and ‘restoration and English language, article and review types, dentistry field. Their bibliometric data including publication title, authorship, citation count, citation dentistry, year of publication, country and institution of origin, journal of publication, study design, and keywords were extracted and analyzed.Results and Discussion: To our knowledge, this is the first bibliometric article on composite resin restorations. This study provides information about authors, institutions and countries that contribute to significant improvements in composite resin restorations. From 2000 to 2020, there were 7118 articles published from 99 countries.Articles originate primarily from the USA and Brazil. Results indicate that the USA, Brazil, Germany, Turkey, the United Kingdom, Japan, Swtizerland, Italy, Netherlands and India are the leading countries in composite resin restoration research and account for 51.8% of the total number of publications. The total number of citations are 158.404, corresponding to 22 citations per paper publication. During the time period examined, 776 hot articles and 228 classic articles on composite resin restorations were found.The journal with the most publications is ‘Operative Dentistry’. The publishing houses of the top 10 journals are from 4 countries: USA(6),Netherlands(2),Germany(1),Japan(1). The most cited article within the boundaires of this study is Ferracane’s article titled ‘Resin composite-State of the art’, which was published in Dental Materials in 2011 and received 913 citations.

Deep eutectic solvents (DESs) have emerged as viable alternatives to the toxic organic solvents. The most intriguing aspect of these solvents is perhaps the widely varying physicochemical properties emerging from the changes in the constituents that form DESs along with their composition. Based on the constituents, a DES can be hydro-philic/polar or hydrophobic/non-polar rendering vastly varying spectrum of polarity a possibility. DESs formed by mixing urea (U) with hydrated lanthanide salts, lanthanum nitrate hexahydrate (La : U), cerium nitrate hexahydrate (Ce : U), and gadolinium nitrate hexahydrate (Gd : U), respectively, exhibit very high polarity as manifested via probe-reported empirical parameters dipolarity/polarizability (π*). The highest π* of 1.70 exhibited by the DES (Gd : U) in 1 : 2 molar ratio is unprecedented. The π* ranges from 1.50 to 1.70 for these DESs, which is almost the highest reported for any solvent system. The π* decreases with increasing urea in the DES, however, the anomalous trends in H-bond donating acidity (α) and H-bond accepting basicity (β) appear to be due to the hydrated water of the lanthanide salt. The emission band maxima of fluo-rescence probe of “effective” dielectric constant (εeff) of the solubilizing media, py-rene-1-carboxaldehyde (PyCHO), in salt-rich DESs reflect higher cybotactic region di-polarity than even that offered by water. Probe Nile red aggregates readily in these DESs to form non-fluorescent H-aggregates; a characteristic of highly polar solvents. Behavior of probe pyranine also corroborates these outcomes as the (lanthanide salt : urea) DES system supports the formation of deprotonated form of the probe in the excited-state. The (lanthanide salt : urea) DES system offers solubilizing media of exceptionally high polarity, which is bound to expand their application potential.

Imbalance of homeostasis between the microbial communities and the host system leads to dysbiosis in oral micro flora. DMTU (1,3-di-m-tolyl-urea), is a biocompatible compound that was shown to inhibit Streptococcus mutansbiofilms by inhibiting its communication system (quorum sensing). Here, we hypothesized that DMTU is able to inhibit multispecies biofilms. We developed a multispecies oral biofilm model comprising an early colonizer Streptococcus gordonii, a bridge colonizer Fusobacterium nucleatum, and late colonizers Porphyromonas gingivalis, Aggregatibacter actinomycetemcomitans. We performed comprehensive investigations to demonstrate the effect of DMTU on planktonic cells and biofilms. Our findings showed that DMTU inhibits and disrupts multispecies biofilms without bactericidal effects. Mechanistic studies revealed significant down regulation of biofilm and virulence related genes in P. gingivalis. Taken together, our study highlights the potential of DMTU to inhibit polymicrobial biofilm communities and their virulence.

Single-cell green microalga Nannochloropsis oceanica is potentially considered to be the bioresource for biofuel and pharmaceutical production. Urea is a kind of nutrient component for photosyn-thetic N. oceanica. Meanwhile, urea could induce to accumulate some substances such as lipid and affect its growth and physiology. However, how marine microalga N. oceanica respond and adapt to urea addition remains elusive. Here, acclimation of the metabolic reprogramming to changes in the nutrient environment was studied by high-throughput mRNA sequencing in N. oceanica under Ct vs U, there were 2104 genes displayed differential expression (including 1354 upregulation and 750 downregulation, respectively) and some pathways including carbon/nitrogen metabolism, photosynthesis, and lipid metabolism would be reprogrammed in N. oceanica. The results showed that genes related to photosynthesis in N. oceanica were significantly down-regulated, especially those related to light harvesting proteins. Interestingly, urea absorption and transport may de-pend not only on specialized transport mechanisms such as urease, but also on alternative transport channels such as the ABC transporter family, CLC protein family. In addition, urea causes specific changes in carbon and lipid metabolism. Genes associated with the Calvin cycle and carbon concentration mechanisms were significantly upregulated. In lipid metabolism, genes associated with lipases, or polyunsaturated fatty acid enzymes, are highly activated. In addition, expression is enhanced in the tricarboxylic acid cycle and folate metabolism, making important contributions to energy supply and synthesis and modification of genes or macromolecules. These phenomena indicate that N. oceanica actively and dynamically regulates the redistribution of carbon and nitrogen after urea addition., which will provide references for further research on the effects of urea on N. oceanica.

In Mexico there is a deficit in the production of pine resin, because it depends on natural forests. Therefore, it is necessary to select provenances and phenotypes of potential species such as P. oocarpa. The objective was to determine the difference between provenances and the variation of resin components and quality, as well as the effect of geographic and climatic factors. Resin from five provenances was collected from southern Mexico. The percentage of rosin, turpentine and water was obtained, as well as the acidity and saponification index. P. oocarpa resin had 80.94 % rosin, 7.7 % turpentine and 11.49 % water. The saponification and acidity index was 125.47 and 117.49 mg KOH.g_1, respectively. All variables showed differences (p≤ 0.0001) between provenances. The provenance contributed between 6.44 and 11.71 % to the total variance, the error contributed between 88.29 and 93.56 %. Geographic and climatic variables only had an effect on the percentage of turpentine; the correlation was negative with altitude and longitude, but positive with temperature and precipitation. The results allow defining seed collection sites for resin plantations and orienting the selection for a P. oocarpa improvement program.

Formaldehyde (HCHO), an indoor volatile organic compound, is seriously harmful to human health. Therefore, green and effective decomposition of HCHO is essential. TiO₂ has been employed for the degradation of HCHO via photocatalytic generation of reactive oxygen species (ROS) (O^2-, ·OH), yet the low specific surface area of crystalline TiO₂ depressed the catalytic performance. Herein, we prepared TiO₂ aerogels with high specific surface area and high porosity by sol-gel method, and added PVA to introduce flexible molecular chains for pore size regulation. The photocatalytic performance test verifies that the pore size of TiO₂ aerogel is one of the important factors for HCHO decomposition. Notably, through the establishment of theoretical model and calculation, we validated that the efficiency of HCHO decomposition is related to the oxygen pressure in the pores of TiO₂ aerogel, and the oxygen pressure is inversely proportional to the pore size. Accordingly, the optimal pore size of TiO₂ aerogel for the photocatalytic HCHO decomposition is 2 nm~10 nm. This study provides a theoretical idea for TiO₂ aerogels in the decomposition reaction of HCHO, which is expected to inspire more breakthroughs in the study of TiO₂ aerogels for green chemistry.

Formaldehyde (HCHO), an indoor volatile organic compound, is seriously harmful to human health. Therefore, green and effective decomposition of HCHO is essential. TiO2 has been employed for the degradation of HCHO via photocatalytic generation of reactive oxygen species (ROS) (O2-, ·OH), yet the low specific surface area of crystalline TiO2 depressed the catalytic performance. Herein, we prepared TiO2 aerogels with high specific surface area and high porosity by sol-gel method, and added PVA to introduce flexible molecular chains for pore size regulation. The photocatalytic performance test verifies that the pore size of TiO2 aerogel is one of the important factors for HCHO decomposition. Notably, through the establishment of theoretical model and calculation, we validated that the efficiency of HCHO decomposition is related to the oxygen pressure in the pores of TiO2 aerogel, and the oxygen pressure is inversely proportional to the pore size. Accordingly, the optimal pore size of TiO2 aerogel for the photocatalytic HCHO decomposition is 2 nm-10 nm. This study provides a theoretical idea for TiO2 aerogels in the decomposition reaction of HCHO, which is expected to inspire more breakthroughs in the study of TiO2 aerogels for green chemistry.

Protein synthesis has been a very rich target for developing classes of drugs to control prokaryotic and eukaryotic pathogens. Despite the development of new drug formulations, treating human cutaneous and visceral Leishmaniasis still needs significant improvement due to considerable side effects and low adherence to the usual treatment regimen. In this work, we show that the di-substituted urea-derived compound I-17 is effective in inhibiting the promastigote forms and intracellular amastigotes of the Leishmania (L.) amazonensis and L. infantum species, in addition to exhibiting low macrophage cytotoxicity. We also show a potential immunomodulatory effect of I-17 in infected macrophages, which exhibited increased expression of inducible Nitric Oxide Synthase (NOS2) and Nitric Oxide (NO) production. Our data suggest that I-17 and new derivatives of this compound may be helpful in developing new drugs for treating leishmaniasis.

In this work, PMMA(Poly methyl methacrylate) microfluidic system was used as a micro-reactor for urea hydrolysis by urease enzyme with use conductivity principle and utilize sound level meter(SLM) App in smartphone as a novel detector by considering the peak height in the App as an indicate for urea concentration. the advantage of use small volume and how the reaction carried on in the microfluidic system with simple and low cost are discussed, and the results were analyzed and statically determine. The linearity, detection limit (3×noise )and Correlation Coefficient, 62.5-500 ppm, 31.25 ppm and 0.992 respectively also, recovery studied were between(98.5-100.13%).

The solid particle erosion at room and elevated temperatures of pure and filled hot-curing epoxy resin on anhydride hardener was experimentally tested using accelerated method on special bench. Micro-sized dispersed industrial wastes were used as fillers: fly-ash from a power plant and spent filling material from a copper mining and processing plant. The results showed that the unfilled resin wear significantly decreases with increasing temperature, while the dependence on the temperature of the wear intensity at an impingement angle of 45o is linear inversely proportional, and at an angle of 90o non-linear. The decrease in wear intensity is probably due to an increase in elasticity (an increase in the fracture strain limit) because of heating. Solid particle erosion of the examined filled epoxy compounds is considerably higher than that of unfilled compounds at impingement angles of 90o and 45o. Filled compounds showed ambiguous dependences of intensity of wear from temperature (especially at an angle of attack 45o), probably, character of dependence is defined by a filler share and the structural features of the samples caused by distribution of particles of the filler. Intensity of wear of the considered compounds at impingement angles 90o and 45o has high direct correlation with density and the modulus of elasticity (i.e., increases with their increase), and low correlation with bending strength of the considered materials. The data set for determining the correlation between mechanical properties and wear included characteristics due to both compound filling and test temperature.

Detection of formaldehyde is very important in terms of life protection, as it can cause serious injury to eyes, skin, mouth and gastrointestinal function if indirectly inhaled and hence researchers are putting effort in developing novel and sensitive device. In this work, we have fabricated an electro-chemical sensor in the form of a field effect transistor (FET) to detect formaldehyde over wide range (10 nM to 1 mM). For this, ZnO nanosheets (NS) were first synthesized by hydrothermal method with in-situ deposition on cleaned SiO₂ coated Si (100) substrate. The synthesized materials were characterized for morphology and purity and surface area (31.718 m²/g). The developed device was tested for formaldehyde detection at room temperature that resulted in a linear response with concentration (96%), sensitivity value of 0.27 mA/M/cm² and a low detection limit of 210 nM, and a high 0.93194 return.

There is an increasing interest in applying environmentally-friendly materials in wood protection technology. This include the use of less toxic active ingredients, as well as better fixation. This study investigates the formulation based on the combination of copper and Saqez resin on the physical and biological resistance properties of poplar wood. Samples were treated by either copper-ethanolamine (Cu/MEA) and/or Saqez resin at various treatment levels. A vacuum pressure procedure was applied. The retention, weight percent gain, water absorption, volumetric swelling, and decay resistance of the samples were then determined. The highest retention and weight percent gain were obtained at the samples treated with the combination of copper-based system and Saqez resin. Additionally, the combination of the copper and Saqez improved the physical properties and decay-resistance against white-rot fungus Trametes versicolor.

This paper considers a new approach to the modeling of the vacuum infusion process at the manufacturing three-dimensional composite parts of complex shape. The developed approach and numerical methods are focused on the reliable prediction with the needed accuracy and elimination the unrecoverable defect of composite structure such as the dry spots. The paper presents some experimental results, which demonstrate two cases of dry spots formation in large aircraft composite panels, and analyses the reasons of these defects arising. Our numerical technique is based on the vacuum infusion of the liquid resin into porous preform as the two phase flow, which is described by the phase field equation coupled with the Richards equation describing the fluid motion in unsaturated soils with spatially varied pressure dependant porosity and saturation. This problem statement allowed to correctly reconstruct the resin front motion and formation of inner and outer dry spots depending on its movement. For the rapid detection of preform zones that are suspicious for defect formation two indicators calculated during process simulation are proposed and tested at the numerical experiments. The auxiliary program tool has been developed in MATLAB environment to correctly detect the times of formation, localization and dimensions of the arising dry spots by using the results of the finite element model simulation.

In this present study, 3-pentadecyl-phenol was selected as a modifier to prepare a foamable phenolic resin with excellent performance, which was successfully prepared by in-situ modification. Fourier transform infrared spectroscopy (FT-IR) and nuclear magnetic resonance (¹H NMR, ¹³C-NMR) were used to test and characterize the molecular structure of the modified resin. The results showed that 3-pentadecyl-phenol successfully modified the molecular structure of phenolic resin with a reduction in resin gel time. The effect of changing the added amount of 3-pentadecyl-phenol on the mechanical properties, microstructure and flame retardancy of the modified foam was investigated. The results showed that when the amount of added 3-pentadecyl-phenol was 15% of the total amount of phenol, this resulted in the best toughness of the modified foam, which could be increased to 300% compared to the bending deflection of the unmodified phenolic foam. The cell structure showed that the modified phenolic foam formed a more regular and dense network structure and the closed cell ratio was high. Furthermore, the compressive strength, bending strength, and limited oxygen index were improved, while the water absorption rate was lowered. However, the foam density could be kept below 40 mg/cm³, which does not affect the load.

In the present work, an innovative range of foams, based on flax gum-filled epoxy resin was developed, reinforced or not by flax fibers. Foams and composites with different gum and epoxy resin contents were produced and characterized for mechanical and thermal performances. To enhance the organic flax gum filler's cross-linking, we exploited the oxidized components' reactivity with the amine hardener (isophorone diamine). We compared the materials obtained with those derived from the native components. Flax gum and fibers were primarily characterized by chemical analysis, NMR, and FTIR to evaluate the mild oxidation of native materials. The formation of chemical bonds between oxidized polymer chains, epoxy resin, and hardener has been evidenced by FTIR, and the materials were then studied by SEM, X-ray computed micro-tomography (CT), and submitted to mechanical and thermal tests. The relevance of oxidation treatment was highlighted, through a significant increase in density and mechanical performances (+36% and +81%, respectively for the 100% flax gum material). The positive effect of flax fibers on homogeneity evidenced through micro-CT analysis was also clearly addressed. This set of promising results paves the way for future development of fully flax-based insulation composite materials.

Palm fatty acid distillate (PFAD) is a by-product from the refining of crude palm oil. It comprises mainly of free fatty acids, having around 45% of palmitic and 33% oleic acids as the major components. Ultra-violet (UV) curable urethane acrylate (UA) oligomers could be synthesized from PFAD by the following procedure. A hydroxyl terminated macromer was first prepared by reacting PFAD with a mixture of isophthalic acid, phthalic anhydride, neopentagylcol (NPG) and pentaerythritol. The macromer is then reacted with 2-hydroxylethylacrylate (2HEA) and toluene diisocynate (TDI) to generate a resin containing acrylate side chains for UV curable application. A series of UA resins were prepared by using 15, 25, 45, 55 and 70% of PFAD respectively. The UA resin has Mw in the range of 3200 to 27,000. They could be cured by UV irradiation at intensity of 225mW/cm². Glass transition temperature (T_g) of the cured film was measured by differential scanning calorimeter (DSC), and hardness of the film was determined by pendulum hardness tester according to ASTM4366. The resins were used in wood coating application. All of the cured films showed good adhesion, hardness and chemical resistant for resins using up to 55% PFAD; however the resin at 70% did not cure properly.

In today’s world, it is the need of the hour to adopt new technology to sustain the production of the future. Nanotechnology is gaining popularity for its efficiency in various applied fields of science. In agriculture, nanomaterials have a huge impact on the efficiency of fertilizers pesticides, etc. As it requires very fewer quantities and has a negligible residual effect the environment is safe with the innovation of Nano fertilizer. Keeping this view into account an experimental Trial at a farmer’s field was carried out at Berui village in the Hooghly District of West Bengal during the winter (rabi) season of 2019 – 20 under the supervision of Berui Cooperative, KVK-Hooghly, BCKV, and IFFCO with nano-Urea, nano-Zn and nano-Cu using RBD design with 10 treatments and 3 replications. Experimental results revealed that the highest tuber yield was obtained in T-7 (50% N+100% P & K+ 2 spray of nano-Urea), and that was followed by T-10 (50% N + 100% P & K + 50% Zn + 1 spray each of Nano-Urea, Zn and Cu) and T-8 (100% N-P-K + 50% Zn + 2 spray of Nano-Zn). The performance of nano fertilizers, Nano- Urea, was quite promising and economically viable as compared to the 100% recommended dose with commercial fertilizers (RDF).

Urea, a prevalent component found in wastewater, shows great promise as an alternative substrate to water for energy-efficient hydrogen production by electrolysis. However, the sluggish kinetics of the anodic urea oxidation reaction (UOR) significantly hampers the overall reaction rate. To address this challenge, this article presents a comprehensive study focusing on the controlled fabrication of hierarchically structured nanomaterials as potential catalysts for UOR. The prepared MnO2@NiCo-LDH hybrid catalyst demonstrates remarkable improvements in reaction kinetics, benefiting from synergistic enhancements in charge transfer and efficient mass transport facilitated by its unique three-dimensional architecture. Notably, the catalyst exhibits an exceptionally low onset potential of 1.228 V and requires only 1.326 V to achieve an impressive current density of 100 mA cm-2, representing a state-of-the-art performance in UOR. These findings highlight the tremendous potential of this innovative material-designing strategy to drive advancements in electrocatalytic processes.

Thirteen benzylethylenearyl ureas and one carbamate have been designed, synthesized and biologically evaluated as regards their antiproliferative activity on tumor cell lines HEK-293 and A-549 and on the immune and endothelial Jurkat T cells and HMEC-1, respectively. A relationship between the structure of the synthetic compounds and their antiproliferative activity has been established. Compounds C.1, C.3, C.12 and C.14 were chosen for further biological studies in order to determine their potential as oncoimmunomodulating agents. Some compounds exhibited significant inhibitory effects on both total PD-L1 and VEGFR-2 in HT-29 cell line, showing urea C.12 active against both targets. Some compounds could reduce more than 50% of cancer living cells, compared to non-treated ones, when assessed in co-cultures using HT-29 and THP-1 cells. In addition, these compounds showed no effect on the immune cell viability and significantly reduce CD11b expression, which is a promising target for immune modulation in anti-cancer therapies.

A portable urea sensor for use in the fast flow condition was fabricated using porous polytetrafluoroethylene (PTFE) membranes coated with amine-functionalized parylene, parylene-A, by vapor deposition. To generate a specific electrochemical sensor signal from urea, the urea-hydrolyzing enzyme urease was immobilized on the parylene-A-coated PTFE membranes via chemical crosslinking using glutaraldehyde. The urease-immobilized membranes were assembled in a polydimethylsiloxane (PDMS) fluidic chamber, and a screen-printed carbon three-electrode system was used for electrochemical measurements. The success of urease immobilization was confirmed using fluorescence microscopy, scanning electron microscopy, and Fourier-transform infrared spectroscopy. The optimum concentration of urease for immobilization on the parylene-A-coated PTFE membranes was determined to be 48 mg/mL, and the optimum number of membranes in the PDMS chamber was found to be 8. Using these optimized conditions, we fabricated the urea biosensor and monitored urea samples under various flow rates ranging from 0.5 to 10 mL/min in the flow condition using chronoamperometry. To test the applicability of the sensor for physiological samples, we used it for monitoring urea concentration in the waste peritoneal dialysate of a patient with chronic renal failure, at a flow rate of 0.5 mL/min.

Keywords: apoptosis; arbutus unedo L; formaldehyde; hippocampus; oxidative stress

In this article, bio-composites derived from starch-glycerol biodegradable matrix reinforced with jute fibers have been fabricated using the wet hand lay-up and compression moulding techniques. Samples having different weight percentages of jute fiber in the starch matrix have been analysed. The fibers surface was chemically treated by alkaline sodium hydroxide for improving the interphase bonding between fiber and matrix. Tensile test for the composites were done and the sample with highest tensile strength was selected for further tests that included water absorption, scanning electron microscopy and thermal analysis. It has been concluded that the ultimate tensile strength was found to be maximum for the composition of 15% fiber by weight composite as 7.547 MPa without epoxy coating and 10.43 MPa with epoxy coating. The major disadvantage of bio-composite is its high water absorption property, which in this study has been inhibited by the epoxy resin layer. Herein, the results of various tests done disclose a noteworthy improvement in the overall properties of bio-composite, in comparison to the neat biodegradable starch matrix.

This study investigated the effect of replacing part of the dietary soybean meal with either polymer-coated urea or gelatinized starch urea on the performance, nutrient digestibility, blood biochemical indexes, ruminal fermentation and rumen microflora of Angus heifers. The urea release profiles of two kinds of slow-release urea were evaluated in vitro and indicated a superior nitrogen retention with the polymer-coated urea. 210 purebred Angus cattle (BW = 314.26 kg) were divided into three groups: no urea group (CON), polymer-coated urea group (PCU), gelatinized starch urea group (GSU), 20g/kg polymer-coated urea or 25g/kg gelatinized starch urea was used to replace part of soybean meal in the concentrate feed respectively according to the principle of iso-metabolic energy and iso-nitrogenous. During the whole experiment, the ADG of PCU group was higher than both the GSU group and the CON group. The feed-weight ratio of the PCU group was significantly lower than both the GSU group and the CON group during the 90-day feeding period. The ADF apparent digestibility in the PCU group was significantly higher than that of the CON group, and extremely significantly higher than that of the GSU group. On the 86th day, the ALB content in the PCU group was significantly higher than that in the CON group. The contents of acetic acid and butyric acid, total volatile fatty acid and propionic acid were significantly higher in the PCU group than in the CON group. Bacterial diversity analysis found that the abundance of Firmicutes was higher in the PCU group than that in the GSU group and the CON group at the phylum level, and inverse result was observed in Bacteroidetes. The abundance of Paraprevotella was higher in the PCU group, whereas higher abundance of Prevotella was found in the GSU group at the genus level. These results indicate that both polymer-coated urea and gelatinized starch urea can replace part of soybean meal in the diet, and the amount of substitution in this trial had no diverse effect on the performance of Angus heifers, and the effect and economic benefits brought by polymer-coated urea were better than gelatinized starch urea.

The very slow anodic oxygen evolution reaction (OER) greatly limits the development of large-scale hydrogen production via water electrolysis. By replacing OER with easier urea oxidation reaction (UOR), developing a HER/UOR coupling electrolysis system for hydrogen production can significantly save energy and costs. Al doped cobalt ferrocyanide (Al-Co2Fe(CN)6) nanocube array was in-situ grown on nickel foam (Al-Co2Fe(CN)6/NF). Due to the unique nanocube array structure and regulated electronic structure of Al-Co2Fe(CN)6, the as-prepared Al-Co2Fe(CN)6/NF electrode exhibited outstanding catalytic activities and long-term stability to both UOR and HER. The Al-Co2Fe(CN)6/NF electrode needed potentials of 0.169 V and 1.118 V (vs. reversible hydrogen electrode) to drive 10 mA cm−2 for HER and UOR, respectively, in alkaline condition. Applying the Al-Co2Fe(CN)6/NF to a whole urea electrolysis system, 10 mA cm−2 was achieved at a cell voltage of 1.357 V, which saved 60% electricity energy comparing to that of tranditional water splitting. Density functional theory calculations demonstrated that the boosted UOR activity comes from Co sites with Al doped electronic environments. This promoted and balanced the adsorption/desorption of main intermediates in UOR process. This work indicates that Co based materials as efficient catalysts have great prospects for application in urea electrolysis systems, and are expected to achieve low-cost and energy-saving H2 production.

: This study was aimed at assessing adaptation and bonding of discontinuous (short) glass fiber-reinforced composite to intraradicular dentin EverX Flow (GC Corporation, Tokyo, Japan), when used as intracanal composite filling and anchorage instead of traditional fiber posts. (2) Methods: Seventy intact extracted human teeth were endodontically treated and randomly divided into 6 groups (n=10), depending on the materials used in the post space. In Group 1, a 2-bottle universal adhesive G2 Bond Universal + EverX Flow were tested. In group 2, a single-component universal adhesive G-Premio Bond + EverX Flow were used. In groups 3 and 4 the same materials are tested, but after cleaning of the canal walls with 17% EDTA and final irrigation with 5.25% NaOCl Ultrasound Activated. In the last three Groups (5-7) traditional prefabricated GC Fiber Posts 1.6 mm silanized with G-Multi Primer for 1 minute are cemented with a dual-cured composite resin cement (GradiaCore), after ultrasonic irrigation in the groups 6 and 7. In each group, 1 mm-thick slices from each sample (n=10) were cut for light microscope and SEM inspection for study materials adaption to the dentin and for measuring push-out strength of post / cemement material to the dentin / prefabricated post. These results were statistically analyzed: as the data distribution was not normal, the Kruskal-Wallis Analysis of Variance by Ranks had to be applied. The level of significance was set at p<0.05. Results: Push-out forces varied between 6.66-8.37 MPa. No statistically significant differences were recorded among the groups. Microscopic examination showed that ultrasonic irri-gation increased adaptation of the materials to the dentin surface. There was a trend of higher bond strength among the tested groups when EverX Flow was used. Also, the type of failure was more often cohesive when ultrasonic irrigation and two-step adhesive system were used. Conclusions: Within the limitations of this in vitro study, it may be concluded that when EverX Flow was used for intracanal anchorage in the post-endodontic recon-struction, similar push-out retentive forces and strength to those of traditional fiber posts cemented with particulate filler resin composite cements were achieved. Although further studies are necessary, EverX Flow represents an effective alternative to traditional fiber post adhesion in particular when used in combination with the two-step adhesive system and ultrasonic activation.

The study aimed to elucidate the optimum level of elemental sulfur, fresh cassava root (FCR), and urea and their effect on gas production, ruminal fermentation, thiocyanate concentration, and in vitro degradability. A 3×2×4 in a completely randomized design were conducted. Factor A was level of sulfur at 0%, 1%, and 2% of concentrate dry matter (DM), factor B was level of urea at 2% and 4% of concentrate DM, and factor C was level of the FCR at 0, 200, 300, and 400 mg of the total substrate. The study found that elemental sulfur, urea, and FCR had no interaction effect on the kinetics of gas, ruminal fermentation, hydrogen cyanide (HCN), and in vitro degradability. Elemental sulfur supplementation (P<0.05) significantly increased the gas produced from an insoluble fraction (b), in vitro DM degradability and either neutral detergent fiber or acid detergent fiber degradability, and propionate (C3) concentration while decreased the ruminal HCN concentration. Urea levels showed a (P<0.05) significant increase of the potential extent of gas production, ruminal NH3-N, and total volatile fatty acid (VFA). FCR supplementation (P<0.05) significantly increased the gas produced from an immediate soluble fraction (a), gas produced from insoluble fraction, gas production rate constant, total VFA, C3 concentration, and HCN while decreased ruminal pH, acetate, and butyrate concentration. It could be concluded that 2% elemental sulfur, 4% urea, and 300 mg FCR showed a greater effect on gas production, ruminal fermentation, and HCN reduction.

Abstract: Uranium is a toxic radioactive element and is usually found in the environment in hexavalent form. It has become a necessity to remove uranium, which can enter the environment in excessive amounts through nuclear industrial activities, from access waters. Melamine formaldehyde organo clay nano composite foam (MFCNCF) was prepared as a novel adsorbent by hardening with thermal treatment. Structural, crystallographic textural and surface morphological characterization of the prepared adsorbent was made by FTIR and XRD spectroscopic and SEM and HRTEM microscopic techniques. This study aims to investigate the adsorption of U(VI) from aqueous solution by MF organo clay nanocomposite and its dependence on various variables such as initial uranium concentration, adsorption time, adsorbent dosage, initial pH, and temperature. Additionally, adsorption isotherm analysis and adsorption kinetics and thermodynamics were also examined. For this purpose, the batch adsorption experiments were carried out and the equilibrium concentration of U(VI) in the aqueous solution was measured with a UV-Vis spectrophotometer at a wavelength of 433 nm, which corresponds to its maximum absorptivity. The results regarding adsorption kinetics show that 30 min is sufficient to reach adsorption equilibrium and the data show a high fit to the pseudo-second-order kinetic model. Isotherm analysis also revealed a high fit of the data to the Type III isotherm and the Halsey model. Based on this fit, an adsorption mechanism involving two regions (electrostatic and complex formation) was proposed for the current adsorption system. The adsorption isosteric enthalpy and entropy values for the first and second regions are 3.65 and -51.02kJ/mol and 1.77 and -167.28J/mol, respectively. It was found in kmol. Experimental results showed that the prepared nanocomposite foam adsorbent is an effective and potential alternative for the effective removal of U(VI) from aqueous solutions.

Commiphora molmol myrrh resin extracts, which have different physical properties such as polarity and dielectric constant, were prepared by immersion in extraction solvents (hot water, DMSO, hexane, ethanol, and methanol). Methanolic myrrh resin extracts showed broad antibacterial activity against isolated airborne bacteria. Furanoeudesma-1,3-diene and curzerene, as the main terpenoids in the methanolic myrrh resin extract, were analyzed using GC-MS, and the methanolic myrrh resin extracts were found to have antiviral activity (81.2% viral RNA inhibition) against H1N1 influenza virus. Biochars (wood powder-and rice husk-derived) coated with myrrh resin extracts also showed antiviral activity (22.6% and 24.3% viral RNA inhibition), due to the adsorption of terpenoids onto biochar. Myrrh resin extract using methanol as the extraction solvent is a promising agent with antibacterial and antiviral efficacy, and it can be utilized as a novel material via adsorption onto biochar for air filtration processes, cosmetics, fertilizers, drug delivery, and corrosion inhibition.

Synthesis of new series of 1-phenyl-3-(4-(pyridin-3-yl) phenyl) urea derivatives and its in vitro antiproliferative activities against NCI-60 human cancer cell lines of nine different cancer types are described. Fourteen compounds 5a-n have been synthesized with three different hydrogen bondable moieties (4-hydroxylmethylpiperidinyl and trimethoxyphenyloxy and 4-hydroxyethylpiperazine) attached to the core structure 1-phenyl-3-(4-(pyridin-3-yl) phenyl) urea. Different substituents with different π and σ values were added on the terminal phenyl group. Compounds with 4-hydroxymethylpiperidine moiety showed higher mean percentage inhibition values over the 60-cell line panel at 10-µM concentration. They showed broad-spectrum antiproliferative activity over many cell lines of different cancer types. For instance, compound 5a elicited some lethal rather than inhibition effects on SK-MEL-5 melanoma cell line, 786-0, A498, RXF 393 renal cancer cell lines, and MDA-MB-468 breast cancer cell line by 146.1, 108.7, 136.2, 134.8, 116.6 % at 10 µM, respectively. Compounds 5a-e exhibited superior antiproliferative activity than Paclitaxel and Gefitinib against the most sensitive cell lines. Two compounds, 5a and 5d showed promising mean growth inhibitions and thus were further tested at five-dose testing mode to determine their IC₅₀ values. The data revealed that 5a and 5d urea compounds are the most active derivatives with significant efficacies and superior potencies than Paclitaxel in 21 different cancer cell lines, belonging particularly to renal cancer and melanoma cell lines. Moreover, 5a and 5d had superior potencies than Gefitinib in 38 and 34 cancer cell lines, respectively; belonging particularly to colon cancer, breast cancer and melanoma cell lines.

This research explores the depolymerization of waste polymethyl methacrylate (PMMAW) from dental material in fixed-bed semi-batch reactors, focusing on three production scales: laboratory, technical, and pilot. The study investigates the thermal degradation mechanism and kinetics of PMMAW through thermogravimetric (TG) and differential scanning calorimetry (DSC) analyses, revealing a two-step degradation process. The heat flow during PMMAW decomposition is measured by DSC, providing essential parameters for designing pyrolysis processes. The results demonstrate the potential of DSC for energetic analysis and process design, with attention to standardization challenges. Material balance analysis across the production scales reveals a temperature gradient across the fixed bed negatively impacting liquid yield and methyl methacrylate (MMA) concentration. Reactor load and power load variables are introduced, demonstrating decreased temperature with increased process scale. The study identifies the influence of temperature on MMA concentration in the liquid fraction, emphasizing the importance of controlling temperature for efficient depolymerization. Furthermore, the research highlights the formation of aromatic hydrocarbons from the remaining char, indicating a shift in liquid composition during the depolymerization process. The study concludes that lower temperatures below 450 °C favor liquid fractions rich in MMA, suggesting the benefits of lower temperatures and slower heating rates in semi-batch depolymerization. The findings contribute to a novel approach in analyzing pyrolysis processes, emphasizing reactor design and economic considerations for recycling viability. Future research aims to refine and standardize the analysis and design protocols for pyrolysis and similar processes.

Advancements in 3D printing technologies have led to new implementations in rapid prototyping, microfluidics, tooling, dentistry, biomedical devices, drug delivery, and tissue engineering. Stereolithography techniques, which are photopolymerization-based processes, contribute to the optical, chemical, and mechanical properties of 3D printed materials using versatile polymer chemistry. This study used potassium titanate powder (K2Ti8O17) as an additive to enhance the mechanical strength of photocurable resins. PEG was selected as the stabilizer to optimize the dispersion and precipitation of potassium titanate. The flexural strength, hardness, and tensile strength were compared to assess the mechanical strength of the 3D printing resin. The flexural strengths of the printed specimens were in the range of 15–39 N/mm2. The measured surface hardness and tensile strength were 41–80 HV and 2.3–15 N/mm2, respectively. The output resolution of the potassium titanate/acrylate resin was tested using a line-pattern structure. 3D printing resin without stabilizers produced lines with a thickness of 0.3 mm, whereas 3D printing resin containing a stabilizer produced lines with a thickness of 0.2 mm. The flexural strength and pattern thickness results suggest that the potassium titanate/acrylate resin can be utilized as a 3D printer resin, suggesting new possibilities for potassium titanate materials.

Polyurethane (PU) foam adhesives were prepared from castor oil as a polyol with isocyanate poly (4,4′-methylene diphenyl isocyanate) (PMDI) using a solvent-free process. The NCO/OH molar ratio used for the preparation of PU foams was 1.5. Water, organosiloxane and dibutyltin dilaurate were blowing agent, surfactant and catalyst, respectively. Effects of the ratio of blowing agent and catalyst were adjusted to optimize the properties. The results show that 4 wt% of castor oil of catalyst and blowing agent minimizes water absorption and maximizes volume expansion in the PU foams. FT-IR analysis shows that urethane bond was formed by hydroxyl group of castor oil and –NCO group of isocyanate PMDI. More blowing agent and catalyst could improve the volume expansion ratio and reduce water retention of PU foams. It was found that Moso bamboo charcoal (Phyllostachys pubescens) or/and China fir wood particle (Cunninghamia lanceolate) composites with setting densities of 500 and 600 kg/m³ can be prepared from optimized castor oil-based PU foam adhesive at 100 °C for 5 min under a pressure of 1.5 MPa. Increasing the amount of bamboo charcoal decreases the equilibrium moisture content, water absorption and internal bonding strength of the composite. Notably, bamboo charcoal composite exhibits excellent dimensional stability. The optimized density and bamboo charcoal percentages of the composite were 500 kg/m³ and 50 to 100%. The castor oil-based PU composites containing bamboo charcoal fulfilled the CNS 2215 standards for particleboard. This dimensionally stable, low-density bamboo charcoal composite has high potential to replace current indoor building materials.

The aim of this study was to using a lignin based resin (LB) to improve the performance of the soy flour based adhesive. Soy flour (SF), polyamidoamine-epichlorohydrin (PAE), LB was used to develop a plywood adhesive. The solid content and viscosity of the adhesive, functional groups, thermo-stability, and crystallinity of the cured adhesive were characterized and the performance of the resultant adhesive was evaluated by fabricating three-ply plywood. Results showed using LB and PAE mixture to modify SF adhesive improves dry and wet bond strength by 66.3 and 184.2%. PAE contributed more for the wet bond strength improvement and the LB contributed more for the dry bond strength. The improvement was attributed to: 1) LB/PAE reacted with the functions of the soy protein and form a cross-linking network; 2) Polycondensation reaction between LB molecules further improved crosslinking density of the adhesive and formed a interpenetration structure with crosslinked protein; 3)The easy penetration of LB on wood surface and formed more interlock with wood. The denser structure created by LB and PAE mixture improved the thermal stability and decreased the crystallinity of cured adhesive. The usage of the LB and PAE mixture increased solid content by 35.5%, meanwhile, makes its viscosity acceptable for the industrial application.

Shell nacre from Pinctada species has been extensively researched for managing bone defects. However, there is a gap in the research on using shell nacre as cement with improved physico-chemical properties. To address this, the current study aimed to develop a chemical curable com-posite shell nacre cement (SNC) using shell nacre powder and an organically modified ceramic resin shell nacre containing ladder-structured siloxane methacrylate (SNLSM). Different amounts of shell nacre (24, 48, and 72 weight(wt)%) were added to the SNLSM resin matrix and the effect on the physicochemical properties of the cement was studied. The composite shell nacre cement SNC 72 containing 72 wt% shell nacre exhibited significantly higher mechanical properties (com-pressive strength >100 MPa, flexural strength > 35 MPa) and low linear polymerization shrinkage (0.4%) than other compositions. SNC 72 was radiopaque and the exotherm generated during the curing of the cement was minimal. Direct contact of cured SNC 72 with L929 cells revealed the non-cytotoxic nature of the cement. Overall, the results of the study proved that the composite SNC 72 would be a promising candidate for bone defect management.

Clay minerals surfaces potentially played a role in prebiotic synthesis through adsorption of organic monomers that give rise to highly concentrated systems; facilitate condensation and polymerization reactions; protection of early biomolecules from hydrolysis and photolysis; and surface-templating for specific adsorption and synthesis of organic molecules. This review presents processes of clay formation using saponite as a model clay mineral since it is shown to catalyze organic reactions, easy to synthesize in large and pure form, and has tunable properties. In particular, a method involving urea is presented as a reasonable analog of natural processes. The method involves a two-step process – 1) formation of the precursor aluminosilicate gel and 2) hydrolysis of a divalent metal (Mg, Ni, Co, Zn) by the slow release of ammonia from urea decomposition. The aluminosilicate gels in the first step forms a 4-fold-coordinated Al³⁺ similar to what is found in nature such as in volcanic glass. The use of urea, a compound figuring in many prebiotic model reactions, circumvents the formation of undesirable brucite, Mg(OH)₂, in the final product by slowly releasing ammonia thereby controlling the hydrolysis of magnesium. In addition, the substitution of B and Ga for Si and Al in saponite is also described The saponite products from this urea-assisted synthesis were tested as catalysts for several organic reactions including Friedel-Crafts alkylation, cracking and isomerization reactions.

Recent studies have been able to detect α-synuclein (αSyn) seeding in formaldehyde-fixed paraffin-embedded (FFPE) tissues from patients with synucleinopathies using seed amplification assays (SAAs), but with relatively low sensitivity due to limited protein extraction efficiency. With the aim of introducing an alternative option to frozen tissues, we developed a streamlined protein extraction protocol for evaluating disease-specific seeding in FFPE human brain. We evaluated the protein extraction efficiency of different tissue preparations, deparaffinizations, and protein extraction buffers using formaldehyde-fixed and FFPE tissue of a single Lewy body disease (LBD) subject. Alternatively, we incorporated heat-induced antigen-retrieval and dissociation using a commercially available kit. Our novel protein extraction protocol has been optimized to work with 10 sections of 4.5-µm-thickness or 2-mm-diameter micro-punch of FFPE tissue that can be used to seed SAAs. We demonstrated that extracted proteins from FFPE still preserve seeding potential and further show disease-specific seeding in LBD and multiple system atrophy. To the best of our knowledge, our study is the first to recapitulate disease-specific αSyn seeding behavior in FFPE human brain, with structural validation. Our findings open new perspectives in re-evaluating archived human brain tissue, extending the disease-specific seeding assays to larger cohorts to facilitate molecular subtyping of synucleinopathies.

Wheat and corn silages are widely used as ruminant feed in Israel due to their availability and cost-effectiveness. To ensure long-term preservation without compromising nutritional quality, effective methods must be employed. Inclusion of additives during harvest and ensiling can enhance efficiency and address preservation challenges. In the current study, the effects of microbial inoculum (MI) and urea on the chemical composition, amino acid profiles, aerobic stability, and in vitro digestibility of wheat and corn silages were investigated. Samples of wheat and corn were subjected to four treatments: control, MI, Urea, and a combination of MI+Urea. The treatments were ensiled in anaerobic conditions and opened after 1, 7, 14, or 28 days. Results showed that additives improved the quality parameters of wheat and corn silages. The inclusion of MI produced the most aerobically stable silages. The inclusion of urea in silages deteriorated aerobic stability. Additives improved in vitro cell wall carbohydrates digestibility in both silages and was the best when MI was combined with urea. These results imply additives could be incorporated in silages to enhance their nutritional value, aerobic stability and digestibility. Nonetheless, increased CP content with additives was not accompanied with parallel increase in amino acids content in corn silage.

In this study, the properties of unsaturated polyester resin were studied in the presence of recycled ceramic waste particles. Herein, composites were created that contained 28.5-50 wt% porcelain particles (particle size <180 µm). High filler contents increased the gel time and decreased the exotherm temperature of unsaturated polyester resin during curing. The obtained results showed that physical parameters, such as the resin density and porosity, increased as the filler content increased. In addition, the X-ray diffraction results indicated that the produced samples were a combination of ceramic waste particles and unsaturated polyester resin, resulting in semi crystalline structure. The results showed that the maximum water absorption at 40°C increased from 0.97 to 1.5% as the filler content increased from 28.5 to 50 wt%; in this process, the materials experienced a color change but did not lose mechanical performance. Finally, the samples were characterized by thermogravimetric analysis (TGA) to study the effect of porcelain powder on the thermal degradation of the resin. The TGA scans were analyzed with the Friedman method. The results indicated that the samples with porcelain powder exhibited substantially better thermal stability than unsaturated polyester resin.

Asphalt cement will not last for a long time as the world encounters a diminishment in the crude oil. For sustainable, flexible pavement development, new resources can provide a contribution to replace it partially or entirely. In this study, asphalt was partially and entirely replaced by guayule resin as a bioresource by-product, extracted during the guayule natural rubber production. Crumb rubber modifier (CRM) was used as an asphalt enhancer. The Superpave grading system was followed at high, intermediate, and low temperatures to evaluate such innovative binder for rutting, fatigue, and thermal cracking, respectively, in addition to viscosity. Therefore, the original, short-term aging and long-term aging were simulated using tank, rolling thin film oven, and pressure aging vessel materials. Additionally, component analysis using Fourier-transform infrared spectroscopy was provided to link the rheological properties with the chemical changes. Outcomes showed a relatively much lower viscosity of guayule in the same high-temperature asphalt grade indicating savings in plant energy consumption and reduced environmental emissions. CRM enhanced guayule, but not as much as asphalt, proven by polymeric component migration through liquid binder. This enhancement was reflected in the rheological performance besides other factors. As-received guayule seems to have high oxygen content proven by strong absorption peak intensities of oxidative bonds (e.g., Carbonyl and sulfoxide). Such pre-oxidation was negatively reflected in the intermediate- and low-temperature performance of guayule and guayule-based binders. However, the investigated guayule had potential to compensate for asphalt replacement in the presence of CRM by 23–42% by weight of blend.

Prostate-specific membrane antigen (PSMA) has been identified as a target for the development of theranostic agents. In our current work, we describe the design and synthesis of novel N-[N-[(S)-1,3-dicarboxypropyl]carbamoyl]-(S)-L-lysine (DCL) urea-based PSMA inhibitors with a chlorine-substituted aromatic fragment at the lysine ε-nitrogen atom, a dipeptide as peptide fragment of the linker, including two phenylalanine residues in the L-configuration, and 3- or 4-(tributylstannyl)benzoic acid as prosthetic group in their structures for radiolabeling. The standard compounds ([127I]PSMA-m-IB and [127I]PSMA-p-IB) for comparative and characterization studies were firstly synthesized using two alternative synthetic approaches. An important advantage of the alternative synthetic approach in which the prosthetic group (NHS-activated esters of compounds) is first conjugated with the polypeptide sequence, followed by replacement of the Sn(Bu)3 group with radioiodine, is that the radionuclide is introduced in the final step of synthesis, thereby minimizing operating time with iodine-123 during the radiolabeling process. The obtained DCL urea-based PSMA inhibitors were radiolabeled with iodine-123. The radiolabeling optimization results showed that the radiochemical yield of [123I]PSMA-p-IB was higher than those of [123I]PSMA-m-IB, which were 74.9± 1.0% and 49.4 ± 1.2%, respectively. The radiochemical purity of [123I]PSMA-p-IB after purification was greater than 99.50%. The initial preclinical evaluation of [123I]PSMA-p-IB demonstrated a considerable affinity and specific binding to PC-3 PIP (PSMA-expressing cells) in vitro. The in vivo biodistribution of this new radioligand [123I]PSMA-p-IB showed less accumulation than [177Lu]Lu-PSMA-617 in several normal organs (liver, kidney and bone). These results warrants further preclinical development including toxicology evaluation and experiments in tumor-bearing mice.

Dental polymers are often advertised and selected for use in restorations based upon the flexural strength of prefabricated discs, which may not accurately reflect their performance in dental applications. The objectives of this study were, therefore, to determine whether the three-point bending (3PB) test for flexural strength would be predictive of the “crunch-the-crown” CTC test for the failure load. Three brands of polymers (Trilor, Juvora, and Pekkton) were fabricated into rectangular bars and fully contoured crowns (10 specimens of each polymer brand, 30 specimens of each shape). Bars were tested in 3PB to determine flexural strength, and crowns were CTC tested to determine failure load after luting to resin abutments. Statistical significance was evaluated by one-way ANOVA ( = 0.05) and Pearson’s correlation coefficient. The fracture mechanisms were characterized by scanning electron microscopy (SEM). There were significant differences (p < 0.05) in the mean crown failure loads (Trilor [7,033 N] > Juvora [5,217 N] > Pekkton [3,023 N]) and mean flexural strengths of the bars (Trilor [468 MPa] > Juvora [197 MPa] = Pekkton [192 MPa]). There were no correlations between flexural strength and failure load. The mode of crown fracture was different between the polymers, and included deformation (Juvora), ductile-to-brittle fracture (Pekkton), and a combination of cracks and deformation (Trilor). The flexural strength was not correlated with the corresponding crown failure load. Dental practitioners should not rely on the value of flexural strength obtained from the three-point bending test, as advertised from the manufacturer, to predict the performance of polymeric crowns.

In order to improve the performance of soft plantation wood, an environmentally friendly inorganic-organic hybrid wood modifier was developed. First, using urea and melamine as crosslinking agents, the waterborne glucose silicone resin (MUG) was prepared with glucose under the catalysis of inorganic acid and metal ions. Then MUG resin was diluted to 10% and 20% mass fraction, and compounded with sodium silicate (S) of 20% and 10% mass fraction, so the inorganic-organic hybrid G10S20 and G20S10 wood modifier were obtained respectively. Then plantation poplar wood (Populus tomentosa) were impregnated and modified with them. Their physical and mechanical properties were tested and compared with those of the wood treated with S of 20% mass fraction (S20). Infrared analysis showed that amino resin characteristic structure (CO-NH-) existed in MUG resin. The resin has good permeability. Compared with S20 modified wood, the degree of shrinkage of G10S20 or G20S10 modified wood is reduced, their moisture absorption is reduced, and their dimensional stability is improved. Waterborne glucose silicone modifier can effectively improve the wood density, modulus of elasticity, modulus of rapture and compression strength. SEM analysis showed that the cell wall of G20S10 modified wood was significantly thicker than the untreated wood, and there were columnar and granular solid substances attached in some cell cavities, ducts and corners, etc. EDX showed that the number of Si elements on the cell wall was significantly increased compared with the control, indicating that the modifier effectively entered the wood cell wall. The waterborne glucose silicone resin can greatly improve the physical and mechanical properties of wood through organic-inorganic hybridization. It is a green, non-formaldehyde, eco-friendly, low cost, compound wood modifier with broad application prospects.

The soil microbial community serves as a crucial indicator for assessing soil fertility and health. The composition and activity of soil microorganisms reflect the soil's well-being and its ability to provide proper nutrients for crops. Fertilization plays a prominent role in enhancing soil fertility, and novel types of fertilizers, such as stabilized fertilizers with nitrification/urease inhibitors and coated fertilizers, have gained popularity in rice and maize cultivation. However, the long-term effects of these stabilized and coated urea fertilizers on soil chemical properties, microbial di-versity and community structure, as well as nitrogen cycling functional genes, remain unclear. Therefore, it is essential to investigate the impact of extended use of stabilized and coated urea fertilizers on soil fertility and microbiota in rice paddy fields. This research will provide scientific and theoretical support for the development and promotion of stabilized and coated urea ferti-lizers. To examine the effects of long-term application of these stabilized and coated urea fertilizers on soil chemical properties and microorganisms in rice paddy fields, soil samples were collected from brown soil rice paddy fields treated with various urease and nitrification inhibitors, stable urea, sulfur-coated urea (SCU), and resin-coated urea (PCU). The study revealed that 16 years of long-term use of conventional urea nitrogen fertilizer led to a considerable reduction in soil TP. On the other hand, NBPT and conventional urea fertilizers, when applied for an extended period, significantly increased soil organic matter (SOM). Moreover, except for HQ and NBPT+DMPP, the prolonged application of new urea fertilizers also signifi-cantly enhanced soil total potassium (TK). Notably, among all the treatments, PCU treatment had higher values for various soil chemical properties. In the case of SCU fertilizer used in brown soil rice paddy fields, it resulted in a significant decrease in soil pH over time. However, this change in pH did not affect the population of ammonia-oxidizing bacteria (AOB), as it was primarily in-fluenced by soil available nitrogen. DMPP, HQ+DCD, NBPT+DMPP, SCU, and PCU significantly reduced the copy number of bacterial 16S rRNA genes in the soil, with the coated urea fertilizers (SCU and PCU) having a greater impact. The long-term use of stabilized urea fertilizers containing HQ significantly reduced the bacterial community in rice paddy soil. Conversely, HQ+DCD stable urea fertilizer significantly increased the population structure and abundance of Basidiomycota fungi while decreasing the population structure and abundance of Rozellomycota fungi. DMPP stabilized urea fertilizer notably increased the population structure and abundance of Ascomycota fungi while decreasing the population structure and abundance of Rozellmycota and Chytridiomycota fungi. Further-more, HQ stabilized urea fertilizer significantly reduced the population structure and abundance of Chytridiomycota fungi. It is important to note that SCU fertilizer is not suitable for long-term application in neutral to slightly acidic meadow brown soil with a background pH. On the other hand, stable urea fertilizers and resin-coated urea fertilizers containing HQ, NBPT, DCD, DMPP, and their combinations are suitable for long-term application in neutral to slightly acidic meadow brown soil.

In these last years, self-healing polymers have emerged as a topic of considerable interest owing to their capability to partially restore material properties and thereby extend the product's lifespan. The main purpose of this study is to investigate the nano-indentation response in terms of hardness, reduced modulus, contact depth and coefficient of friction of a self-healing resin developed for use in aeronautical and aerospace contexts. To achieve this, the bifunctional epoxy precursor underwent tailored functionalization to improve its toughness, facilitating effective compatibilization with a rubber phase dispersed within the host epoxy resin. This approach aimed to highlight the significant impact of the quantity and distribution of rubber domains within the resin on enhancing its mechanical properties. The main results are that pure resin exhibits a higher hardness (about 36.7% more) and reduced modulus (about 7% more), consequently leading to a lower contact depth and coefficient of friction (11.4% less) compared to other formulations that, conversely, are well-suited for preserving damage from mechanical stresses due to their capabilities in absorbing mechanical energy. Furthermore, finite element method (FEM) simulations of the nanoindentation process were conducted. The numerical results were meticulously compared with experimental data, demonstrating a good agreement. This validation of the FEM model underscores its efficacy in predicting the mechanical behavior of nanocomposite materials under nanoindentation. The proposed investigation aims to contribute knowledge and optimization tips about self-healing resins.

In this study, the effect of ZnO nanoparticles (Zn NPs) on the performance of epoxy resin composites was investigated. The new ZnO/epoxy resin composites were synthesized using halloysite nanotubes (HNT) and different types of ZnO nanoparticles (commercial ZnO and ZnO-ODTES). These ZnO nanoparticles were utilized for intending to enhance the interfacial bonding between the epoxy resin and the reinforcement. Various methods such as FTIR, TGA, DSC, TEM-EDX, and Nanoindentation analyses were used to prove that the ZnO nanoparticles can improve the properties of epoxy resin composites. The thermal properties of the epoxy resin composites were enhanced to a greater extent by the addition of ZnO NPS. DSC testing proved that the epoxy resin composites modified with ZnO NPS are more flexible and elastic than unmodified epoxy resin. It was seen that the epoxy resin modified with ZnO-ODTES shows a much improved hardness and penetration depth compared to the other samples. These findings can pave the way for the developing of ZnO-based marine coatings with improved properties.

In this study, cotton fabric reinforced phenolic resin (CPF) composites were modified by adding four two-dimensional fillers: graphitic carbon nitride (g-C3N4), graphite (Gr), molybdenum disulfide (MoS2), and hexagonal boron nitride (h-BN). The tribological properties of these modified materials were investigated under dry friction and water lubrication conditions. CPF/ Gr composite exhibits significantly better tribological performance than the other three fillers modified CPF composites under dry friction, with a 24% reduction in friction coefficient and a 78% reduction in wear rate compared to unmodified CPF composite. Under water lubrication conditions, all four fillers did not significantly alter the friction coefficient of the CPF composite. However, except for an excessive amount of Gr, the other three fillers can reduce the wear rate. Particularly, in the case of 10% MoS2 content, the wear rate decreased by 56%. Scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) were employed for the analysis of the morphology and composition of the transfer films. Additionally, molecular dynamics (MD) simulations were conducted to investigate the adsorption effects of Gr, MoS2, and PF on the counterpart surface under both dry friction and water lubrication conditions. The difference in the adsorption capacity of Gr and MoS2 on the counterpart, as well as the resulting formation of transfer films, accounts for the variation in tribological behavior between CPF/Gr and CPF/MoS2 composites. By combining the lubrication properties of MoS2 and Gr under dry friction and water lubrication conditions, using them as co-fillers can achieve a synergistic lubrication effect.

This study focused on the optimization of the flexural strength of bio-composite samples of palm kernel, whelks, clams, periwinkles shells and bamboo fiber, reinforced with resin for engineering applications. The aim of the study was to: formulate different samples of bio-composite reinforce with resin for engineering applications and to evaluate the flexural strength, of the fabricated composite. The hand lay-up technique was used for the composites produced by incorporating different percentage compositions of the shells/fiber (10%, 15%, 20%, 25% and 30%) into varied proportions of epoxy resin and catalyst. The cured samples after 24hours were subjected to tensile, impact, flexural and water absorption test. The experiments were conducted using Taguchi optimization method L25 (5x5) with five design parameters and five level combinations in Minitab 18 statistical software. The results showed that the average values of flexural was 114.87MPa when compared to the unreinforced of 72.33MPa bio-composite. The study recommended that agricultural waste like palm kernel shells, whelk shells, clams, periwinkle shells and bamboo fiber, should be converted into important engineering applications.

Literature revealed the potential of using guayule resin for asphalt cement replacement from the binder’s perspective. However, monitoring guayule resin through binder-aggregate mixture could disclose its performance through field. In this study, designated binders were employed to investigate the applicability of such an innovative replacer through mixture, which were neat asphalt and guayule-based binders (neat guayule, asphalt-rubber-guayule, guayule-rubber binders). Consecutively, field-simulated lab mixtures were prepared to investigate the major distresses. Moisture damage, rutting, fatigue cracking, and thermal cracking resistances were investigated using the modified Lottman (TSR) test, rut test by asphalt pavement analyzer (APA), semi-circular bending (SCB) test, and disk-shaped compact tension (DCT) test, respectively. Additionally, the Hamburg wheel-tracking (HWT) test was employed to evaluate moisture susceptibility and rutting resistance. Outcomes revealed that the neat guayule was susceptible to moisture damage at a 7% air content (V_a) when the TSR test was employed. In contrast, all investigated mixtures yielded perfect performances against moisture susceptibility under the HWT test. Guayule-based mixtures perfectly resisted rutting, as analyzed by the rut test and HWT test. Generally, changing parameters (e.g., V_a, rubber addition, and partial asphalt replacement by guayule and rubber) enhanced the guayule-based mixture resistance to rutting and moisture damage resulting in acceptable performances. Guayule-based mixture had a high fracture toughness at low temperatures, hence fatigue fracture resistance at intermediate temperatures. Neat guayule mixture with or without rubber addition did not entirely resist thermal fracture. However, partial asphalt replacement by guayule and rubber resisted the thermal fracture to a great extent.

The nanocomposites with reversible cross-linking covalent bonds were prepared by reacting furfurylamine (FA)-modified diglycidyl ether of bisphenol A (DGEBA) and furfuryl-functionalized aniline trimer-modified graphene (TFAT-G) with bismaleimide (BMI) via Diels-Alder (DA) reaction. The successful synthesis of the TFAT modifier is confirmed by NMR hydrogen spectroscopy and IR spectroscopy tests. The structure and properties of TFAT-G epoxy nanocomposites are characterized by SEM, DSC, tensile and resistivity CES. The results show that TFAT-G was uniformly dispersed in the resin, and 1wt% TFAT-G composites increase to 233% for tensile strength, 63% for elongation at break, 66.1% for modulus and 7.8℃ for Tg. Overall, the graphene/self-healing resin nanocomposites have both good self-healing function and electrical conductivity by adding 1% modified graphene and still maintain the original 83% strength and 89% electrical conductivity after one cycle of heating repair.

Repairing of small and isolated delamination area in carbon fiber reinforced polymer (CFRP) without significantly altering the composite structure is studied in this research. A small drilled hole was introduced at the center of the delamination section of CFRP, providing the channel for epoxy infill of sharp delamination cracks. The pressureless infill repair was achieved through the capillary action of an acetone-diluted resin solution (without hardener) with CNT reinforcement, e.g., 89 m/m% of acetone, 10 m/m% of resin and 1m/m% of CNT. Such an acetone-rich resin pre-coating (RPC) solution is easy to prepare and apply to the drilled hole area. Curing of CNT-toughened resin infill was induced by filling the small-drilled hole with a resin-hardener mixture toughened by CNT/Aramid pulp. The effectiveness of delamination repair with curing periods of two weeks and three months were compared. Flexural strength measurements indicated that 77% (potentially 100%) of the restoration was achievable.

This research seeks to interpret the component analysis of an innovative bio-asphalt binder using guayule resin in addition to crumb rubber modifier (CRM) at high concentrations. Such asphalt modification aims to minimize the dependency on virgin asphalt binder and provide new solutions concerning sustainable, flexible pavement industry. Guayule resin is a promising bioresource for asphalt binder replacement. By now, it could be considered a no value byproduct extracted during the guayule natural rubber production. CRM is a recycled material derived from scrap tires. The provided interpretation could help in understanding the asphalt-rubber-guayule interaction mechanism. Fourier transform infrared spectroscopy (FTIR), supported by thermo-gravimetric analysis (TGA), was used to investigate the component analyses of guayule resin composition, asphalt guayule interaction, and asphalt rubber guayule interaction, compared to corresponding asphalt rubber interaction. Additionally, the rheological properties at elevated temperatures were provided to link the microscale properties with the final product performance. The study clarified the distinct carbon and hydrogen compositional elements of guayule resin. Asphalt and guayule resin have similarities in chemical composition and rheological behavior with temperature susceptibility. The asphalt guayule binder had physical interaction. However, when both interacted with rubber, a chemical interaction was attributed, with no difference in rubber dissolution tendency, in asphalt rubber guayule, compared to asphalt rubber. A bio-binder composed of 62.5% asphalt, 25% guayule and 12.5% CRM had the potential to provide rheological properties better than base asphalt. Such behavior was interpreted by a high release of rubber components.

Objectives: The current study aimed to compare the adaptation of the restored class-I cavities with two self-etch adhesives bonded to two resin composite using cross-polarization optical coherence tomography (CP-OCT). Materials and Methods: Cylindrical class-I cavities were prepared on twenty, extracted human premolars. Two self-etch adhesives; Clearfil SE bond 2 (SE; Kuraray Noritake Dental, Japan) and Bond Force (Palfique Bond) adhesive (PL; Tokuyama Dental, Japan) were used in this study that were bonded to either resin composites materials; Herculite XRV microhybrid dental composite (HRV; Kerr, Italy) or Estelite Alpha composite (ESA; Tokuyama Dental, Japan). The specimens were divided into four groups (n=5); SE-HRV, SE-ESA, PL-HRV and PL-ESA. All specimens were varnished and stored in distilled water for 24h. Then, they were submerged in a contrasting medium. After that, all groups were optically imaged under CP-OCT at every 250 µm interval distance. Later, image binarization and gap quantification were carried out using Image analysis software. Result: There was a significant difference between all the groups except between SE-ESA and PL-ESA (p = 0.51). The highest median gap % was seen in PL-HRV group followed by SE-ESA, PL-ESA and SE-HRV. Conclusion: Other than composite filler loading and adhesive formula, the interactions of the adhesive and composite copolymers have great influence on composite adaptation.

Mechanical properties of three-dimensional (3D) printed resin can be improved by decreasing oxygen concentrations during post-curing, and nitrogen saturated post-curing has been applied for the purpose. This study aimed to evaluate and compare the color stability of 3D printed resin crowns post-cured in normal air and nitrogen saturated conditions. Crowns were fabricated with 3D printer and post-cured in normal air (control group; air) or nitrogen saturated condition (experimental group; nitrogen). The specimens in each group were subdivided into four subgroups, each exposed to different discoloration agents: distilled water, coffee, wine, and curry. Post-immersion color changes were measured using a digital spectrophotometer and analyzed through repeated measures ANOVA. Fourier Transform Infrared (FT-IR) spectroscopy evaluated the degree of conversion of resin over immersion times for both post-curing conditions. Comparing the effects of post-curing conditions, significant difference was found between control and experimental groups over immersion time in wine and curry subgroups. In FT-IR analysis, there was significant difference in degree of conversion between the air and nitrogen groups from 10 to 300 seconds. The findings suggest that nitrogen saturated post-curing can potentially enhances the conversion rate of 3D printed resin crowns, thereby improving their color stability.

The article describes the use of microwave irradiation in the synthesis of bis(cyclo carbonate) compounds (BCC) in bulk (without solvent) from carbon dioxide capture using an epoxidized compound - a commercial epoxy resin, and compares this process to the conventional method. CO2 cycloaddition to epoxides is an ecological and efficient method for the formation of bis(cyclic carbonates). Moreover, the introduction of gas into the reaction mixture was carried out at atmospheric pressure with a controlled flow rate, which is advantageous from an economic point of view. Progressive structural changes and the presence of characteristic chemical groups were monitored using attenuated total reflectance infrared spectroscopy with Fourier transform. The obtained crude products were purified to obtain three fractions, which were subjected to detailed structural analysis using FT-IR and 13CNMR. The formation of the main product with two cyclic carbonates was confirmed. The presence of monomers, dimers and trimers in individual fractions as well as their thermal stability were determined, and the molecular masses in individual fractions were determined using gel permeation chromatography (GPC).

Tree resin, which in addition to its widespread use in industry is also a macroergic component which has not yet been used for energy purposes. The main goal of this work is to determine the energy content of the resin of spruce, pine and larch and wood components – pulp and turpentine. The combustion heats of resin (MJ/kg) from each timber was determined calorimetrically. The energy values of tree resin (&gt;38.0 MJ.kg-1) were 2.2 and 2.4 times higher than that of bleached and unbleached cellulose, the highest value was recorded for the turpentine (&gt;39.0 MJ.kg-1). The best way of resin tapping is the America method, providing 5 kg resin ha-1 yr-1. The resin quantity tapped was raised at least 3 times applying stimulant, its production cost compared to other feedstocks was the cheapest. The tree resin can be applied as a good means to mitigate global warming and consequently dampen climate change. One tonne of tree resin burned instead of coal spares the atmosphere by 5.0 Mt CO2 since it is environmentally neutral. As resin heating values approach to the lower end of ones of liquid hydrocarbon fuels, greater efforts are needed to examine the most efficient energy use of resin.

Nymphaea lotus L. is the medicinal plant that has long been used as food, cosmetic and traditional medicines in Africa and Asia since the ancient time. Its flavonoids and other interesting phytochemical compounds from rhizome, leaf, and the whole flowers have been reported in the previous published researches. However, stamens, which are essential for reproductive functions, may also represent new alternative sources of potential antioxidant flavonoids as investigated in this study. The innovative green chemistry method i.e. ultrasound-assisted extraction (USAE) as well as macroporous resin (MPR) purification procedure were employed in this current research. The optimal ultrasound-assisted extraction condition is 90 % (v/v) aqEtOH with 34.65 khz ultrasonic frequency and 46 minutes of extraction time. Comparing with heat reflux extraction (HRE) conventional method, the significant gain of 1.35 total flavonoids content was obtained using optimized USAE conditions, jumping to 2.80 when this USAE associated with MPR purification. Not only in vitro cell free antioxidant activity of N. lotus stamen extracts, but also in cellulo antioxidant investigation using yeast model showed the same trend to indicate that the best antioxidant flavonoid can be found in USAE coupled with MPR purification. Moreover, the key antioxidant genes expression in yeast model such as SIR2 and SOD2 were also expressed at the highest level in yeast cell treated with the extract from USAE together with MPR purification. Consequently, it can be seen that the USAE combined with MPR purification can help to enhance the flavonoids antioxidant potential of the stamens extract from this medicinal species.

Fertility management techniques being promoted in sub-Saharan Africa (SSA) seek to grow indigenous vegetables economically and sustainably. This study was conducted in a phytotron chamber and compared yield, soil carbon (C) speciation and greenhouse gas (nitrous oxide (N₂O) and carbon dioxide (CO₂)) emissions from SSA soils of two ecoregions; the dry savanna (lna, Republic of Benin) and rainforest (Ife, Nigeria) cultivated with local amaranth (Amaranthus cruentus) under manure (5 t/ha) and/or urea (80 kg N/ha) fertilization. Vegetable yield ranged from 1753 kg/ac to 3198kg/ac in the rainforest, RF, soils and 1281 kg/ac to 1951 kg/ac in the dry savanna, DS, soils. Yield in the urea treatment was slightly higher compared to the manure+urea treatment, but the difference was not statistically significant. Cumulative CO₂ emissions over 21 days ranged from 497.06 to 579.47 g CO₂ in the RF, and 322.96 to 624.97 g CO₂ in the DS, while cumulative N₂O emissions ranged from 60.53 to 220.86 mg N₂O in the RF, and 24.78 to 99.08 mg N₂O in the DS. In the RF samples, the combined use of manure and urea reduced CO₂ and N₂O emissions but led to an increase in the DS samples. ATR-FTIR analysis showed that the combined use of manure and urea increased the rate of microbial degradation in the soils of the DS, but no such effect was observed in soils of the RF. We conclude that combining manure and urea fertilization has different effects on soils of the two ecoregions, and that RF farmers can reduce agricultural emissions without compromising soil productivity and yield potential.

The objective was to compare the color match and color stability behavior of single and multishade resin-based composites (RBCs) used for direct restorations. This review was conducted according to the Preferred Reporting Items for Systematic Reviews and Meta-Analyses guidelines. Randomized clinical trials evaluating the shade performance of single-shade RBCs in direct restorations were included. A search of the scientific literature was performed in 5 databases (April 2024). The meta-analysis was performed using RevMan 5.4, calculating the risk difference (RD) and 95% confidence interval (CI) of the dichotomous outcome using a random effects model. Bias was assessed using the RoB 2.0 tool, and certainty of evidence was assessed using the GRADE tool. Four studies with 263 restorations analyzed were selected. The results showed comparable performance between single-shade RBCs and multishade RBCs in terms of color match and color stability over 12 months. Three studies had a low risk of bias with all expected results, and one study had some concerns. The certainty of evidence for color stability was considered low for all follow-up periods due to the small number of events and sample size. According to the United States Public Health Service Evaluation (USPHS) and the World Dental Federation (FDI), there is comparable clinical color performance between single-shade and multishade RBCs over 12 months.

The present study aimed to characterize the microstructure of a temporary 3D printing resin (Resilab Temp), evaluating the optical properties and mechanical behavior according to different post-processing curing times. For the analysis of the surface microstructure and establishment of the best printing pattern, samples in bar format following ISO 4049 (25 x 10 x 3 mm) were designed in CAD software (Rhinoceros 6.0), printed on the W3D printer (Wilcos), and light-cured in Anycubic Photon at different times (without curing, 16 minutes, 32 minutes, and 1 hour). For the structural characterization, analyses were carried out in FTIR (Fourier Transform Infrared Spectroscopy) and Scanning Electron Microscopy (SEM). The mechanical behavior of the resin was based on flexural strength tests and Knoop microhardness. Color and translucency analysis were performed with a spectrophotometer (VITA Easy Shade Advanced 4.0), which was evaluated following CIELab, using gray, black, and white backgrounds. All analyses were performed immediately after making the samples and repeated after thermal aging with 2 thousand cycles (5-55 °C). The results obtained were statistically analyzed with a significance level of 5%. FT-IR analysis showed about a 46% degree of conversion on the surface and 37% in the center of the resin sample. The flexural strength was higher for the groups polymerized for 32 min and 1h, while the Knoop microhardness did not show a statistical difference between the groups. Color and translucency analysis also did not show statistical differences between groups. According to all the analyses carried out in this study, for the evaluated material, the post-polymerization time of 1 hour can be suggested to improve the mechanical performance of 3D-printed devices.

Milk production from Asiatic swamp buffalo is a new enterprise in Laos. As yields are limited, provision of high-quality Cow-Calf molasses nutrient blocks containing 10% urea (UMNB10) may improve productivity. A trial in a recently established commercial buffalo dairy examined dietary supplementation of lactating buffalo cows with UMNB10, with 3 groups of 9 cows in mid-lactation randomly selected. Two groups received ad-libitum access to UMBs with the remaining group free of block supplements. All animals were daily fed fresh Napier grass (30kg), corn (750gm), rice bran (1.45kg), plus accessed fresh Mulatto grass. Daily milk production (DMP) and body condition score (BCS) were recorded for the 2 months of access to UMB. Average DMP for the 2 supplemented groups were 1.02 litres and 0.96 litres, compared to 0.78 litres for the control group, suggesting improved milk productivity of 31% and 24% from accessing UMB. Partial budget analysis identified a strong incentive for use of the molasses blocks, with a net profit of USD408 and USD295 over a 30-day period for the supplemented groups. Molasses nutrient blocks may be a simple motivator for smallholder farmers in developing countries to increase the efficiency of large ruminant production, improving rural livelihoods, food security and potentially, reducing GHG emissions.

Nanocomposites of cyanate ester resin (CER) filled with three different reactive amino-functionalized polyhedral oligomeric silsesquioxane (POSS) were synthesized and characterized. The addition of a small quantity (0.1 wt.%) of amino-POSS chemically grafted to the CER network led to increasing thermal stability of CER matrix. A significant increase of the glass transition temperature, Tg (DSC data), and the temperature of α relaxation, Tα (DMTA data), by 45-55 оС of CER matrix with loading of nanofillers was evidenced. CER/POSS films exhibited a higher storage modulus than that of neat CER in the temperature range investigated. It was evidenced that CER/aminopropylisobutyl (APIB)-POSS, CER/N-phenylaminopropyl (NPAP)-POSS, and CER/aminoethyl aminopropylisobutyl (AEAPIB)-POSS nanocomposites induced a more homogenous α relaxation phenomenon with higher Tα values and an enhanced nanocomposite elastic behavior. Furthermore, CER/amino-POSS nanocomposites possessed higher specific surface area, gas permeability (CO2, He), and diffusion coefficients (CO2) values than those for neat CER, due to increasing free volume of the nanocomposites studied that is very important for their gas transport properties. Permeability grew respectively by about 2 (He) and 3.5-4 times (СО2), and diffusion coefficient of CO2 increased approximately twice for CER/amino-POSS nanocomposites in comparison with the neat CER network. The efficiency of amino-functionalized POSS in improving the thermal and transport properties of the CER/amino-POSS nanocomposites increased in a raw of reactive POSS containing one primary (APIB-POSS) &lt; eight secondary (NPAP-POSS) &lt; one secondary and one primary (AEAPIB-POSS) amino groups. APIB-POSS had the least strongly pronounced effect, since it could form covalent bonds with the CER network only by reaction of one –NH2 group, while AEAPIB-POSS displayed the most highly marked effect, since it could easily be incorporated into the CER network via reaction of –NH2 and –NH– groups with –O–C≡N groups from CER.

Copper ferrite attracts a lot of interest from researchers as a material with unique magnetic, optical, catalytic and structural properties. In particular, the magnetic properties of this material are structurally sensitive and can be tuned by changing the distribution of Cu and Fe cations in octahedral and tetrahedral positions by controlling synthesis parameters. In this study, we propose a new simple and convenient method for the synthesis of copper ferrite nanoparticles using a strongly basic anion exchange resin in OH form. The effect and possible mechanism of polysaccharides addition on the elemental composition, yield and particle size of CuFe2O4 is investigated and discussed. It is shown that anion exchange resin precipitation leads to a mixture of unstable at standard temperature cubic (c-CuFe2O4) and stable tetragonal (t-CuFe2O4) phases. The effect of the reaction conditions on the c-CuFe2O4 stability is studied by temperature-dependent XRD measurements and discussed in terms of the cations distribution, Jahn−Teller distortion and Cu2+ and oxygen vacancies in the copper ferrite lattice. The obtained differences in the values of saturation magnetization and the coercive force of prepared samples are explained with a reference to variations in the particle sizes and the structural characteristics of copper ferrite.

This study evaluated the efficacy of experimental TEGDMA-functionalized dicalcium phosphate dihydrate (T-DCPD) filler-based resin-based composites (RBC) in preventing caries lesions around the restoration margins (secondary caries”, SC). Standardized Class-II cavities were made in sound molars having the cervical margin in dentin. Cavities were filled with a commercial resin-modified glass-ionomer cement (RMGIC) or experimental RBCs containing a BisGMA-TEGDMA resin blend and one of the following inorganic fractions: 60 wt.% Ba glass (RBC-0); 40 wt.% Ba glass, 20 wt.% T-DCPD (RBC-20); 20 wt.% Ba glass, 40 wt.% T-DCPD (RBC-40). An open-system bioreactor produced S. mutans biofilm-driven SC. Specimens were scanned using micro-CT to evaluate demineralization depths. Scanning Electron Microscopy and Energy-dispersive X-ray Spectroscopy characterized the specimens’ surfaces, while antimicrobial activity, buffering effect, and ion uptake by the biofilms were also evaluated. ANOVA and Tukey’s test were applied at p<0.05. RBC-0 and RBC-20 showed SC development in dentin, while RBC-40 and RMGIC significantly reduced the lesion depth at the restoration margin (p<0.0001). Initial enamel demineralization could be observed only around RBC-0 and RBC-20 restorations. A direct antibiofilm activity could explain SC reduction by RMGIC, while a buffering effect on biofilm’s acidogenicity explained the behavior of RBC-40. Experimental RBC with CaP-releasing functionalized T-DCPD filler could prevent SC with the same efficacy as F-releasing materials.

Tooth decay, also known as caries, is a significant medical problem that harms teeth. Treatment is based on the removal of the carious material and then filling the cavity left in the tooth, most commonly with amalgam or composite resin. The consequences of filling failure include repeating the filling, or performing another treatment, such as a root canal, or extraction. Dental amalgam contains mercury, and there is a global effort to reduce its use. However, no consensus has been reached using randomized clinical trials, regarding whether amalgam or composite resin materials are more durable, and which is the best restorative material. To determine which material is superior, we performed a retrospective cohort study using a large database where members of the 58 dental clinics with 440 dental units were treated. The number of failures of the amalgam compared to composite resin restorations between 2014 and 2021 were compared. Our data included information from over 650,000 patients. Between 2014 - 2021, 260,905 patients were treated. 19,692 out of 113,281 first amalgam restorations failed (17.49%), whereas significantly fewer composite restorations failed (11.98%) 65,943 out of 555,671. This study indicates that composite is superior to amalgam and therefore it is reasonable to cease using mercury containing amalgam.

The pressing process and density profile of particleboards produced with addition of waste wood containing phenol-formaldehyde (PF) resin was presented. The particles were melamine-urea-phenol-formaldehyde (MUPF) resinated. Recovered particles were obtained from post-industrial waste plywood. The press closing time recorded during the pressing of mats containing only recovered particles in the core layer (100%), at a unit pressure of 3 MPa, in which the face layer rate was 50%, resin load for face and core layer was 12% and 10% was shorter by 29% than for the industrial particle mats. Regardless of the level of variability of independent factors the overheating time of mats to a temperature of 100 °C, containing recovered particles was 10% - 20% shorter than the time of overheating mats with industrial particles. The greatest impact (52%) on maximum density of the face layer of particleboards was demonstrated by the content of the recovered particles and the resin load (32%). The maximum density area of the face layer was located closer to the surface in particleboards produced with a higher (80%, 100%) content of the recovered particles, a higher (i.e. 12% and 10%, respectively, for face and core layer) resin load, a lower (35%) face layer rate and a higher (3 MPa ) unit pressure.

Prostate-specific membrane antigen (PSMA) is a well validated prostate cancer marker, but reported PSMA-targeted tracers derived from the Lys-urea-Glu pharmacophore including the clinically validated [99mTc]Tc-EDDA/HYNIC-iPSMA have high off-target uptake in kidneys, spleen and salivary glands. In this study, we synthesized and evaluated three novel 99mTc-labeled PSMA-targeted tracers and investigated if the tracers derived from the Lys-urea-Aad pharmacophore could have minimized uptake in off-target organs/tissues. In vitro competition binding assays showed that compared with HYNIC-iPSMA, the three novel ligands had slightly weaker PSMA binding affinity (average Ki = 3.11 vs 8.96 - 11.6 nM). Imaging and ex vivo biodistribution studies in LNCaP tumor-bearing mice showed that [99mTc]Tc-EDDA/HYNIC-iPSMA and the three novel tracers successfully visualized LNCaP tumor xenografts in SPECT images and were excreted mainly via the renal pathway. The average tumor uptake at 1 h post-injection varied from 5.40 to 18.8 %ID/g, and the tracers derived from the Lys-urea-Aad pharmacophore had much lower uptake in spleen and salivary glands. Compared with the clinical tracer [99mTc]Tc-EDDA/HYNIC-iPSMA, the Lys-urea-Aad derived [99mTc]Tc-EDDA-KL01127 had lower background uptake and superior tumor-to-background contrast ratios, and is therefore promising for clinical translation to detect prostate cancer lesions with SPECT.

This study endeavors the preparation and evaluation of Phenol Furfural Resin (PFR) from bagasse and its nanocomposites for Electrically Conductive Adhesives (ECAs) application. PFR was prepared with the furfural extracted from bagasse using modified acid digestion method. Three different formulations of PFR nanocomposites with conductive nanoparticles i.e., PFR-silver, PFR-graphite, and PFR-silver + graphite were prepared using 20-60 w/w% of fillers via impregnation method. Resultant products were characterized by FT-IR, SEM, EDS and XRD spectroscopy. Electrical conductivity was measured using four probe technique while band gap was calculated via Tauc plot. Virgin PFR has shown poor conductivity up to 2.6 × 10^-4 Scm^-1 while the highest conductivity achieved was 8.2 × 10^-1 Scm^-1 for nanocomposite constituted silver, graphite, and PFR with 40:30:20 ratios respectively. This synergism was exhibited because graphite and Ag NPs supply excellent junctions for building networks. Both tend to coalesce due to van der Waals forces and high surface energies, therefore conductive pathways numbers can be increased, and contact area can be effectively enlarged. This ternary composite has exhibited the lowest bandgap energy value i.e., 3.1 eV. Thermogravimetric temperatures T₀ and T_deg values were increased up to 120 °C and 484 °C respectively, showing significant increase in thermal stability. Therefore, the resultant nanocomposite material has good potential to be employed as ECAs in electronic industry.

This study endeavors the preparation and evaluation of Phenol Furfural Resin (PFR) from bagasse and its nanocomposites for Electrically Conductive Adhesives (ECAs) application. PFR was prepared with the furfural extracted from bagasse using modified acid digestion method. Three different formulations of PFR nanocomposites with conductive nanoparticles i.e., PFR-silver, PFR-graphite, and PFR-silver + graphite were prepared using 20-60 w/w% of fillers via impregnation method. Resultant products were characterized by FT-IR, SEM, EDS and XRD spectroscopy. Electrical conductivity was measured using four probe technique while band gap was calculated via Tauc plot. Virgin PFR has shown poor conductivity up to 2.6 × 10-4 Scm-1 while the highest conductivity achieved was 8.2 × 10-1 Scm-1 for nanocomposite constituted silver, graphite, and PFR with 40:30:20 ratios respectively. This synergism was exhibited because graphite and Ag NPs supply excellent junctions for building networks. Both tend to coalesce due to van der Waals forces and high surface energies, therefore conductive pathways numbers can be increased, and contact area can be effectively enlarged. This ternary composite has exhibited the lowest bandgap energy value i.e., 3.1 eV. Thermogravimetric temperatures T0 and Tdeg values were increased up to 120 °C and 484 °C respectively, showing significant increase in thermal stability. Therefore, the resultant nanocomposite material has good potential to be employed as ECAs in electronic industry.

The reinforcing effect of boehmite nanoparticles (BNP) in epoxy resins for fiber composite lightweight construction is related to the formation of a soft but bound interphase between filler and polymer. The interphase is able to dissipate crack propagation energy and consequently increases the fracture toughness of the epoxy resin. Usually, the nanoparticles are dispersed in the resin and then mixed with the hardener to form an applicable mixture to impregnate the fibers. If one wishes to locally increase the fracture toughness at particularly stressed positions of the fiber-reinforced polymer composites (FRPC), this could be done by spraying nanoparticles from a suspension. However, this would entail high costs for removing the nanoparticles from the ambient air. We propose that a fiber fleece containing bound nanoparticles be inserted at exposed locations. For the present proof-of-concept study, an electrospun polycarbonate nonwoven and taurine modified BNP are proposed. After fabrication of suitable PC/EP/BNP composites, the thermomechanical properties were tested by dynamic mechanical analysis (DMTA). Comparatively, the local nano-mechanical properties such as stiffness and elastic modulus were determined by atomic force microscopy (AFM). An additional investigation of the distribution of the nanoparticles in the epoxy matrix, which is a prerequisite for an effective nanocomposite, is carried out by scanning electron microscopy in transmission mode (TSEM). From the results it can be concluded that the concept of carrier fibers for nanoparticles is viable.

Antimicrobial edible coatings could eliminate pathogen contamination risk on the surface of meat and poultry products during storage. In this study, the edible coating (EC) based on wheat gluten, Pistacia vera L. tree resin (PVR), and essential oil (EO) of PVR were applied on chicken breast fillets (CBF) by dipping method to prevent the growth of Salmonella Typhimurium and Listeria monocytogenes. The samples were packed in foam trays wrapped with low-density polyethylene stretch film and stored at 8°C for 12 days to observe antimicrobial effects and sensory properties. The total bacteria count (TBC), L. monocytogenes, and S. Typhimurium were reported during the storage. All samples coated with EC containing 0.5, 1, 1.5, and 2% v/v EO (ECEO) decreased microbial growth significantly compared to control samples. The growth of TBC, L. monocytogenes, and S. Typhimurium was suppressed by 4.6, 3.2, and 1.6 logs, respectively, at the end of 12 days on the samples coated by ECEO (2%) compared to uncoated controls (p&lt;0.05). Coating with ECEO (2%) also preserved appearance, smell, and general acceptance parameters better than uncoated raw chicken (p&lt;0.05) on the 5th day of storage. In grilled chicken samples, ECEO (2%) did not significantly change the sensory properties of appearance, smell, and texture but had increased taste and general acceptance scores (p&gt;0.05). So, ECEO (2%) can be a feasible and reliable alternative to preserve chicken breast fillets without affecting their sensory properties adversely during the shelf life.

The purpose of the study was to investigate the bacterial viability of the initial biofilm on the surface of experimental modified dental resin composites. Twenty-five healthy individuals with good oral hygiene were included in this study. In a split-mouth design, they received acrylic splints with five experimental composite resin specimens. Four of them were modified with either a novel polymeric hollow beads delivery system or methacrylated polymerizable Irgasan (Antibacterial B), while one specimen served as unmodified control (ST). The delivery system based on Poly-Pore® was loaded with one of the active agents Tego® Protect 5000 (Antiadhesive A), Dimethicone (Antiadhesive B) or Irgasan (Antibacterial A). All study subjects refrained from toothbrushing during the study period. Specimens were detached from the splints after 8h and given a live/dead staining before fluorescence microscopy. Friedman test and post-hoc Nemenyi test were applied with significance level at p &lt; 0.05. In summary all materials but Antibacterial B showed a significant antibacterial effect compared to ST. In conclusion dental resin composites with Poly-Pore loaded active agents show antibacterial effectiveness in situ.

A The aim of this study is to analyze the effect of different endodontic irrigants and adhesive systems on resin bond strength of fiber post cementation. 144 single-rooted, unrestored human teeth were endodontically treated and randomly divided into 12 groups according to 4 endodontic irrigants (distilled water as control; EDTA 17%; NaOCl 5%; clorhexidine 2%) and 3 different adhesive/resin cement systems (etch-and-rinse: ortofosforic acid, Parabond® A+B/Paracore®; self-etch: ParaBond® Non-Rinse Conditioner, Parabond® A+B /Paracore®; Universal: ClearfilTM Universal Bond/ ClearfilTM DC Core Plus). 48 h after post cementation ten teeth from each group were cross sectioned into 3 discs (cervical, middle and apical regions). 30 specimens of each group (n=30) were submitted to push-out test at a crosshead speed of 1 mm/min. The remaining 2 teeth of each group were sectioned in the same manner and the resin-dentin interface was evaluated using scanning electron microscopy (SEM). The results were statistically analyzed with the ANOVA and Tukey’s test (< 0,01). The adhesive protocols and post space region showed no significant effect on bond strength (> 0.01). The combination of NaOCl 5% and ClearfilTM Universal Bond reduced the adhesive strength (< 0.01). The NaOCl 5%, in relation with other irrigants, significantly decreased the push-out bond strength.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

This study aimed to develop a laboratory-scale direct air capture unit for evaluating and comparing amine-based adsorbents under temperature vacuum swing adsorption conditions. The experimental campaign conducted with the direct air capture unit allowed for the determination of equilibrium loading, CO2 uptake capacity, and other main performance parameters of the investigated adsorbent Lewatit VP OC 1065®. The investigations also helped to understand the co-adsorption of both CO2 and H2O on the tested material, which is crucial for improving temperature vacuum swing adsorption processes. This was achieved by obtaining pure component isotherms for CO2 and H2O as well as three different co-adsorption isotherm models from literature. It was found that the weighted average dual-site Toth model emerged as the most accurate and reliable model for simulating this co-adsorption behavior. Its predictions closely align with experimental data, particularly in capturing the adsorption equilibrium at various temperatures. It was also observed that this lab-scale unit offers advantages over thermogravimetric analysis when conducting adsorption experiments on the chosen amine. The final aim of this study is to provide a pathway to develop devices for testing and developing efficient and cost-effective adsorbents for direct air capture.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.