Natural ventilation in a building is an effective way to achieve acceptable indoor air quality. Ventilation dilutes contaminants such as bio-effluents generated by occupants, substances emitted from building materials, and water vapor generated by occupants' activities. In a building that requires heating and cooling, adequate ventilation is crucial to minimize energy consumption while maintaining healthy indoor air quality. However, measuring the actual magnitude of the ventilation rate, including infiltration through the building envelope and airflow through building openings, is not always feasible. In this study, the occupant-generated carbon dioxide (CO2) tracer gas decay method was applied to estimate the ventilation rates in an office room in Seoul, South Korea, from summer to winter. Using the method, real-time ventilation rates can be calculated by monitoring indoor and outdoor CO2 concentrations without injecting a tracer gas. 145mm-diameter circular openings on the fixed glass were used for natural ventilation in the test room. As a result, firstly, the indoor CO2 concentrations were used as an indicator to evaluate how much the indoor air quality deteriorated when all the windows were closed in an occupied office room compared to international standards for indoor air quality. Moreover, we found out the estimated ventilation rates varied depending on various environmental conditions, even with the same openings for natural ventilation. Considering the indoor and outdoor temperature differences and outdoor wind speeds as the main factors influencing the ventilation rates, we analyzed how they affected the ventilation rates in different seasons of South Korea. When the wind speeds were calm, the temperature difference played as a factor that influences the estimated ventilation rates. On the other hands, when the temperature differences were low, the wind speed was the primary factor. This study raises awareness about the risk of poor indoor air quality in office rooms that could lead to health problems or unpleasant working environments. This study presents an example of estimating the ventilation rates in an existing building. In the same way, the ventilation rate in an existing building can be simply estimated while using the building as usual, and appropriate ventilation strategies for the building can be determined to maintain desired indoor air quality.

High-flow oscillatory ventilation (HFOV) is a common rescue treatment in infants and children with respiratory failure. This type of ventilation is an effective technique in numerous diseases that affect a child in the postnatal period, such as ARDS, meconium aspiration syndrome (MIS), postnatal pulmonary bleeding and idiopathic pulmonary hypertension (IPH). Although this ventilation technique is commonly recognized as a valuable therapeutic option in the general pediatric population, this is not the same for children with congenital cardiovascular diseases. The key mechanism of oscillatory ventilation is continuous positive pressure administered within the airways via a small tidal volume at high frequency. Tidal volumes are between 1 and 3 ml/kg delivered at 5 – 15 Hz equivalent to 300 – 900 breaths per minute. Few older studies conducted on humans and animals highlight that HFOV may be dangerous for congenital heart patients. According to these evidences, hemodynamic parameters such as blood pressure, wedge pressure, central venous pressure, heart rate and inotrope level can be dangerously changed for patients with congenital heart disease, therefore oscillatory ventilation should be avoided. Numerous retrospective studies have pointed out how oscillatory ventilation constitutes a valid therapeutic option in children with congenital heart disease. Recently, new evidences have highlighted how hemodynamic parameters are modified in a non-significant way by this type of ventilation, remaining beneficial as in the normal pediatric population. This narrative review aims to describe the mechanisms of oscillatory ventilation and collect all the available evidences to support its use in pediatric patients with congenital heart problems.

Maintaining the optimal microclimate in broiler houses is crucial for bird productivity, yet enabling efficient temperature control remains a significant challenge. This study developed and validated a computational fluid dynamics (CFD) model to predict temporal changes in indoor air temperature in response to variable ventilation operations in a commercial broiler house. The model accurately simulated air velocity and airflow distribution for different numbers of tunnel fans in operation, with air-velocity errors ranging from -0.22 to 0.32 m s-1. The predicted airflow rates through inlets and cooling pads showed good agreement with measured values with an accuracy of up to 108.1%. Additionally, the CFD model effectively predicted temperature dynamics, accounting for chicken heat production and ventilation effect. The model successfully predicted the longitudinal temperature gradients and their variations during ventilation cycles, validating its reliability through comparison with experimental data. The study also explored different variable inlet configurations to mitigate the temperature gradient. The variable inlet adjustment showed the potential to relieve the high temperatures but may reduce overall ventilation efficiency or intensify temperature gradients, which confirms the importance of optimising ventilation strategies. This CFD model provides a valuable tool for evaluating and improving ventilation systems and contributes to enhanced indoor microclimates and productivity in poultry houses.

This study investigates anomaly detection of IoT device traffic using Convolutional Neural Networks (CNN) and Variational Autoencoders (VAE) to enhance the detection capability of security threats in IoT environments. A series of hardware configurations, software environments, and hyperparameters were utilized to optimize the training and testing processes of the models. The CNN model demonstrates robust classification performance, achieving an accuracy rate of 95.85% on the test dataset, effectively distinguishing between different types of IoT device traffic. Meanwhile, the VAE model exhibits proficient anomaly detection capabilities by effectively capturing abnormal patterns in the data using reconstruction loss and KL divergence. The combined use of CNN and VAE models offers a comprehensive solution to cybersecurity challenges in IoT environments. Future research directions include exploring diverse IoT traffic data, practical deployment for validation, and further optimization of model structures and parameters to improve performance and applicability.

The direct detection of dark matter constituents, in particular the weakly interacting massive particles (WIMPs), is central to particle physics and cosmology. In this paper we develop the formalism for WIMP-Nucleus induced transitions from isomeric nuclear states. We specialize it in the case of the experimentally interesting target 180 Ta

Abstract: This article reports the results of an ecological study of cancer incidence rates by state in the US for the period 2016-2020. The goals of this study were to determine the extent to which solar UVB doses still reduced cancer risk compared to findings reported in 2006 for cancer mortality rates for the periods 1950–1969 and 1970-1794 as well as cancer incidence rates for the period 1998–2002 and to determine which factors were recently associated with cancer risk. The cancer data for non-Hispanic white (European American) men and women were obtained from the Centers for Disease Control and Prevention. Indices were obtained for solar UVB at the surface for July 1992, and alcohol consumption, and diabetes and obesity prevalence near the 2016–2020 period. Lung cancer incidence rates were also used in the analyses as a surrogate for smoking, diet, and air pollution. The cancers for which solar UVB is significantly associated with reduced incidence are bladder, brain (males), breast, corpus uteri, esophageal, gastric, non-Hodgkin’s lymphoma, pancreatic, and renal cancer. Lung cancer was significantly associated with colorectal, laryngeal, and renal cancer. Diabetes was also significantly associated with breast, liver, and lung cancer. Obesity prevalence was significantly associated with breast, colorectal and renal cancer. Alcohol consumption was associated with bladder and esophageal cancer. Thus diet has become a very important driver of cancer incidence rates. The role of solar UVB in reducing risk of cancer has been reduced due to people spending less time outdoors, wearing sunscreen that blocks UVB but not UVA radiation, and population increases in overweight and obesity, which lowers 25-hydroxyvitamin D concentrations and generates systemic inflammation, a risk factor for cancer. The dietary approach that would reduce the risk of diabetes, obesity, lung cancer, and, therefore cancer, would be one based mostly on whole-plants and restrictions on red and processed meats and ultraprocessed foods. Solar UVB exposure for a few minutes before applying sunscreen and taking vitamin D supplements would also help reduce risk of cancer.Keywords: alcohol consumption; cancer incidence;

Ammonium sulfate has been utilized in agriculture; however, there is a dearth of research on its application in maize cultivation subsequent to the implementation of nitrification inhibitors or coating. This study aims to analyze the impacts of various combinations of ammonium sulfate fertilizers on soil nutrients, plant nutrient uptake, yield, and fertilizer utilization efficiency in maize cultivation to ascertain the optimal and stabilized disposal method for ammonium sulfate. A completely randomized design was employed with five treatments (AU, the control using urea; AS, treatment using ammonium sulfate; ASN, treatment using ammonium sulfate with a nitrification inhibitor; ASG, treatment using oil-coated ammonium sulfate; ASD, treatment using oil-humic acid-coated ammonium sulfate). Results showed that: (1) Compared with AU and AS, ASN, ASG and ASD decreased the leaching rates of TN, NH4+-N and NO3-N to the 10-20 cm soil layer, and more residual N was obtained in 0-10 cm soil layer. The first-order kinetic equation Nt=N0(1-e-kt) can better fit the process of nitrogen accumulation and release, and the N release rate constant is AU>CK>AS>ASH>ASN>ASD; (2) Compared with AU and AS treatments, the plant dry weight, grain dry weight, spike width, spike length, and yields of maize increased by 8.85-11.08%, 12.98-14.15%, 2.95-3.52%, 5.50-5.65%, and 43.21-51.10% under ASG treatment respectively. The impact of effective spike number on maize yield was found to be significant, as demonstrated by the path analysis conducted in this study. Furthermore, the accumulation levels of nitrogen, phosphorus, and potassium within above-ground plants significantly increased under the ASG treatment compared to the AU and AS treatments. The partial productivity of nitrogen, phosphorus, and potassium increased by 1.43-1.51-fold under ASG treatment, while grain nitrogen balance, grain phosphorus balance, and grain potassium balance increased by 1.41-1.58-fold, 1.51-1.95-fold, and 1.15-l.96-fold respectively. The oil-coated ammonium sulfate, therefore, exhibited the optimal slow-release effect of nutrients, thereby achieving superior performance in enhancing maize production and efficiency.

Chest trauma is one of the most serious and difficult injuries, with various complications that can lead to ventilation - perfusion (V/Q) mismatch and systemic hypoxia. We are presenting a case of 53 – year - old male with no comorbidities or chronic therapy, who was admitted to the Intensive Care Unit due to severe respiratory failure after chest trauma. He developed right - sided pneumothorax and then thoracic drain was placed. On admission, the patient was hemodynamically unstable and tachypneic. The patient was intubated and mechanically ventilated, febrile (38.9°C) and unconscious. A lung CT showed massive non-ventilated areas predominantly in the right lung. He was ventilated with PEEP of 10 cmH2O with a FiO2 of 0.6 – 0.8. Empirical broad-spectrum antimicrobial therapy was immediately initiated. Both high FiO2 and moderate PEEP were maintained and adjusted according to the current blood gas values and oxygen saturation. After Stenotrophomonas maltophilia was identified and treated with sulfamethoxazole/trimethoprim his general condition gradually improved, and he was weaned from mechanical ventilation. In conclusion, both ventilatory and antibiotic therapy were needed to improve oxygenation and outcome of the patient with pneumonia due to the resistant S. maltophilia with V/Q mismatch.

This paper describes a case study of ventilation as well as measured and perceived indoor air quality (IAQ) in a Finnish comprehensive school with a hybrid ventilation system and reported IAQ problems. An operational error was found when investigating the ventilation system that prevented air from coming into classrooms, except for short periods of high carbon dioxide (CO₂) concentrations. However, results indicated that hybrid ventilation system was able to provide adequate ventilation and sufficient IAQ once properly designed and maintained. After ventilation operation was improved, occupants reported less unpleasant odors and stuffy air. The amount of total volatile organic compounds (TVOC) and some single volatile organic compounds (VOCs) decreased. Indoor mycobiota was observed in settled dust in the classrooms, from which ventilation improvement eliminated the dominant, opportunistic human pathogen species Trichoderma citrinoviride found before improvement.

Crop production in Afghanistan suffers from limited phosphorus (P) availability, which severely hinders national agriculture sustainability. This present study hypothesized that deep fertilizer placement could significantly enhance uptake of immobile P and thus tissue P accumulation and crop yield. A two-year pot experiment growing two maize (Zea mays) hybrid cultivars (Xida-789 and Xida-211) was therefore conducted to test these hypotheses under three contrasting fertilizer placement methods (broadcast, side band, and deep band). In doing so, P concentrations in both maize tissues and soils were compared at 45, 60, and 115 days after sowing (DAS) under nine combinations of nitrogen (N) and P fertilizer rates (kg ha-1: N112P45, N112P60, N112P75, N150P45, N150P60, N150P75, N187P45, N187P60, N187P75). Results have shown that deep band placement significantly increased P uptake efficiency, leading to greater P concentration and accumulation in maize tissues compared to other two fertilization methods. This improved P uptake was attributed to several factors associated with deep placement, including reduced P fixation, enhanced root access to P, and moisture availability for P uptake. Additionally, deep band placement combined with higher N application rates (N187 and N150) further enhanced plant P uptake by promoting P availability and utilization mechanisms. Deep band placement also resulted in significantly higher total soil P, Olsen-P, and P use efficiency than broadcast and side band methods, indicating a more efficient P fertilization strategy for maize that can improve growth and yield. This present study also found positive correlations between P concentration in plant organs and soil Olsen-P, highlighting the importance of adequate soil P levels for optimal plant growth. Overall, our results have showed that deep band fertilizer placement emerged as a superior strategy for enhancing P uptake efficiency, utilization, and maize productivity compared to broadcast and side band placement. This approach can potentially optimize P fertilizer utilization, improve maize growth and yield, while minimizing environmental P losses associated with broadcast applications.

Weathering and erosion transport minerals and organics toward the sea or lake bottoms over geologic time. The finest solids are deposited in lower, less turbulent areas, such as lake bottoms and continental shelves. They sometimes stack up to thicknesses of kilometers, and begin compacting. These sediment sections are called shales, and as initially deposited in water, shales can have porosities up to 50-80{\%} water, As they are buried, many alteration products from oil to slate are produced due to overburden and temperature increasess, making them important to study. A preceeding paper \cite{1} showed that pressure solution is the primary mechanism for porosity reduction, with possible mechanical compaction at shallow depths. Without naming the mineral(s) involved, it postulated that the greater the product of the water and pore interfaces, the faster the reaction would proceed. This term is $ \varphi^{4m/3}(1-\varphi)^{4n/3}$ , where $\varphi$ is porosity and m and n are numbers close to unity. The large exponents, {\em 4/3}, recognize that the reaction occurs at the molecular scale at which the surfaces are rough. A second term, $\exp^{(-E/RT)}$ , indicates that the reaction is impeded by a quantum energy barrier, E, with diminished impeding power as increased available thermal energy, represented by the absolute temperature, T, becomes available at greater depths in the Earth. These two factors combine to allow porosity $\varphi$ to reduce with time, or equivalently for the fraction of solids, $(1-\varphi)$, to increase with time,$\left. \frac{\partial(ln(1-\varphi) ) }{\partial t } \right |_{\sigma} = (\varphi )^{4m/3}( 1-\varphi )^{4n/3}Ae^{-E/(RT)}$. { \em Here it is shown that this equation can cover quantitatively any actual deposition rates which may have been experienced by the six sections studied, the actual deposition rates being unknown for these cases. Hence a time-depth depositional history for any new shale section, known in detail, would allow determination of the parameters m, n, E and a lumped proportionality constant A. This was accomplished by showing that, for a wide range of depositional rates, r, the range of E for any of the studied sections is small compared to laboratory measurements of quartz solution\cite{2}, 24+-15kJ/mol. Results were obtained over this range of r's using the previously determined m and n, and porosity and temperature profiles. The presently existing porosity profiles necessarily incorporate any overpressure or underpressure conditions that may have existed in the past or currently, as the net difference between overburden and pore pressure is a primary driving force for pressure solution. $SiO_2$ usually comprises 20-50{\%} of shales. In conclusion, pressure solution of quartz can account for vertical compaction of shales quantitatively in the studied examples. Separately, a quasi-eqivalent method for discussing reduced porosities in Macron 2 versus Macron 1 as increased vertical stress, rather than additional horizontal stress, is illustrated. Experiments are suggested to clarify the pressure solution mechanism. The role of horizontal forces is discussed. From a global point of view, shale compaction by pressure solution is a quantified step in the cycling of continental rocks, beginning with rifting.

Nasal high-frequency oscillatory ventilation (nHFOV) has emerged as an effective initial and rescue noninvasive respiratory support mode for preterm infants with respiratory distress syndrome (RDS). Multiple noninvasive respiratory support modes are currently available in Romania, but little is known about nHFOV use in Romanian neonatal intensive care units (NICUs). We aimed to identify the usage extent and clinical application of nHFOV in Romania. A structured web-based questionnaire was designed to find the rate of nHFOV use and knowledge of this new method of noninvasive respiratory support in Romanian level III NICUs. The questionnaire was addressed to the leaders of all level III Romanian NICUs. Using multiple-choice, open-ended, and yes/no questions, we collected information on the NICU’s size, noninvasive respiratory support modes used, nHFOV use, indications, settings, nasal interfaces, secondary effects, and equipment used. Descriptive statistics and comparisons were performed using IBM SPSS Statistics 26.0. A total of 21/23 (91.3%) leaders from level III NICUs (median [IQR] number of beds of 10 [10-17.5]) responded to the survey. The most frequently used noninvasive ventilation modes were CPAP mode on mechanical ventilators (76.2%), followed by NIPPV (76.2%), heated, humidified high flow nasal cannula (HHHFNC) (61.9%), and nHFOV (11/21 units; 52.4%); 5/11 units reported frequent nHFOV use (in 2 or more newborns/month) in both term and preterm infants. The main indications reported for nHFOV use were CPAP failure (90.9%), hypercapnia (81.8%), and bronchopulmonary dysplasia (72.7%). 10/11 units reported setting a mean airway pressure (MAP) equal to the CPAP level plus 1-2 cmH₂O on rescue nHFOV after CPAP failure. Both dedicated equipment (45.5%) and hybrid ventilators (63.6%) were used for nHFOV delivery, with face/nasal masks and short binasal prongs being the most commonly used nasal interfaces (90.9% and 72.7%, respectively). Air leaks at the interface level (90.9%), thick secretions (81.8%), and airway obstruction (63.6%) were the most frequently mentioned adverse effects of nHFOV; none of the units mentioned pneumothorax as an adverse effect. Only 3 of the NICUs had a written protocol for nHFOV use. Initial, minimum, and maximum amplitude and initial and minimum MAP settings used were significantly higher with hybrid ventilators as compared to dedicated equipment (p<0.05). Most units not yet using nHFOV cited lack of equipment, experience, training, or insufficient information and evidence for the clinical use and outcome of nHFOV use in neonates as the main reasons for not implementing this noninvasive respiratory mode. Our survey showed that nHFOV is already used in more than half of the Romanian level III NICUs to support term and preterm infants with respiratory distress despite a lack of consensus regarding indications and settings during nHFOV. A need for training for nHFOV use was identified, and efforts are needed at the national level to develop courses and training sessions, including using simulation workshops, to offer more information on optimal nHFOV use in clinical practice.

In this paper, we identify several relative ordering properties of the modified proportional hazard rate and modified proportional reversed hazard rate models. For this purpose, we use two well-known relative orderings, namely the relative hazard rate ordering and the relative reversed hazard rate ordering. The investigation is to see how a relative ordering between two possible base distributions for the response distributions in these models is preserved when the parameters of the underlying models are changed. We will give some examples to illustrate the results and the conditions under which they are obtained.

Growing popularity of buildings with integrated sub-systems, requires a review of methods to optimize the preheat of ventilation air. An integrated system permits using geothermal heat storage parallel to the direct outdoor air intake with additional treatment in the mechanical room as a part of building automatic control system. Earth Air Heat Exchanger (EAHX) has many advantages but also has many unanswered questions. Some of the drawbacks are: a possible entry of radon gas, high humidity in the shoulder seasons as well as the need for two different air intake sources with a choice that depends on the actual weather conditions. While in winter, the EAHX may be used continuously to ensure thermal comfort, in other seasons, its operation must be automatically controlled. To generate the missing information about the EAHX technology we have examined two nearly identical EAHX systems, one placed in ground next to the building and the other under the basement slab. In another project, we have reinforced the ground storage action by heat exchanger placed on the return pipes of the hydronic heating system. Effectively, the information provided in this paper, shows advantages of merging both these approaches while the EAHX could be placed under the house or near the basement foundation that is using an exterior basement insulation.

Growing popularity of smart and integrated buildings requires a review of methods to optimize the preheat of ventilation air. An integrated system permits using heat ex-changers located in the mechanical room or in the future even using an exterior wall as a heat exchanger. One may ask the question how does the earth-air heat exchanger (EAHX) technology fitts into this function. EAHX has many advantages but also has many unanswered questions. Some of the drawbacks are: a possible entry of radon gas, high humidity in the shoulder seasons as well as the need for two different air intake sources with a choice that depends on the actual weather conditions. While in winter, the EAHX may be used continuously to ensure thermal comfort, in other seasons, its operation must be automatically controlled. To generate the missing information about the EAHX technology we reviewed literature and examined two nearly identical EAHX systems, placed either in ground next to the building or under the basement slab. Effectively, the information provided in this paper, shows advantages of merging both these approaches while the EAHX shoud be placed under the house or near the basement foundation.

Mechanical ventilation (MV), used in patients with acute lung injury (ALI), induces diaphragmatic myofiber atrophy and contractile inactivity, termed ventilator-induced diaphragm dysfunction. Phosphoinositide 3-kinase- (PI3K-) is crucial in modulating fibrogenesis during the reparative phase of ALI; however, the mechanisms regulating the interactions among MV, myofiber fibrosis, and PI3K- remain unclear. We hypothesized MV with or without bleomycin treatment would increase diaphragm muscle fibrosis through the PI3K- pathway. Five days after receiving a single bolus of 0.075 units bleomycin intratracheally, C57BL/6 mice were exposed to 6 or 10 mL/kg MV for 8 h after receiving 5 mg/kg of AS605240 intraperitoneally. In wild-type mice, bleomycin exposure followed by MV 10 mL/kg prompted significant increases in disruptions of diaphragmatic myofibrillar organization, transforming growth factor-1, oxidative loads, Masson’s trichrome staining, extracellular collagen levels, positive staining of -smooth muscle actin, PI3K- expression, and myonuclear apoptosis (P &lt; 0.05). Decreased diaphragm contractility and peroxisome proliferator activated receptor- coactivator-1 levels were also observed (P &lt; 0.05). MV-augmented bleomycin-induced diaphragm fibrosis and myonuclear apoptosis were attenuated in PI3K-γ-deficient mice and through AS605240-induced inhibition of PI3K- activity (P &lt; 0.05). MV-augmented diaphragm fibrosis after bleomycin-induced ALI is partially mediated through PI3K-γ. Therapy targeting PI3K-γ may ameliorate MV-associated diaphragm fibrosis.

This study investigates by hybrid approach of classical calculations and numerical explicit FEM simulation the strain rate sensitive hardening of Polypropylene Sabic 83MF10 under dynamic tension loads. The Cowper-Symonds model is employed to characterize the non-linear increase in yield strength with strain rate, within the range of 0,01 to 1 [1⁄s]. For lower strain rates, a drastic decrease in yield strength is observed, suggesting the significant influence of creep and relaxation phenomena. The study proposes further research incorporating viscoelastic properties for a more comprehensive material model. Additionally, the study observes a disproportionate increase in yield strength for samples with smaller radius, indicating a dependency on triaxiality which suggests further research on the Drucker-Prager model for this material. The study concludes by recommending a broader range of input parameters for future studies, including the Johnson-Cook model and comparison of tensile test results with compression test results.

This paper examines certain implications from the literature on Tiebout’s model of local gov-ernment service provision, particularly Hamilton’s extension of the model to include local control of land use and property taxation. Our empirical analysis focuses on the use of fiscal zoning to lower property tax rates, a topic that has not been addressed in the extensive Tiebout literature. Using data for over 100 municipalities in the Miami, Florida, metropolitan area, we specify property tax rates as a function of fiscal zoning measures, other municipal characteristics, and tax mimicking. We conclude that single-family zoning is by far the most important variable ex-plaining municipal property tax rates.

A mechanical ventilation system is a big support for breathing complications, in which an external solution is quite necessary to keep oxygen compensation in the patients. Its knowledge is well widespread and different equipment has been developed. However, they are very expensive and their quantity in medical centers is not sufficient, especially in Peru. Hence, it has been required to develop new methods to provide oxygen by a low cost equipment; Protofy, a research group from Spain, designed one of the first low cost mechanical ventilation systems which was medically validated by its government. In this sense, a redesign of the mechanical ventilation system was carried out according to the local requirements and available technology, a different airbag resuscitator with different properties and geometry, but maintaining its working concept based on a cam compression mechanism. Sensors and a display were added to improve the performance with a control algorithm for the rotation frequency and to show the ventilation curves over time to the medical staff. It was necessary to develop a mathematical model to relate the behavior between ventilation curves for a patient and physical variables of the design, especially in the epidemic COVID 19, that many countries are dealing with at the time research is being conducted. The mechanical ventilation system was redesigned, fabricated, and tested measuring its ventilation curves over time. Results indicate that this redesign provides a sturdy equipment able to work during a longer lifetime than the original. The replicability of the ventilation curves behavior is assured, while the mechanism dimensions are adapted for a particular airbag resuscitator. The mathematical model of the whole system can predict satisfactorily the ventilation curves over time and was used to provide the air pressure, volume, and flow as a function of the rotation angle measured by sensors.

Due to poor ventilation conditions in the tunnel, if gas pipeline leaks, the consequence of the accident will be more serious. Therefore, before the emergency repair, gas in the tunnel needs to be excharged so as not to explode during the repair process. Therefore, it is necessary to study the ventilation of gas in the tunnel. Based on the computational fluid dynamics (CFD) theory and taking the Yanyingshan tunnel section of China-Myanmar pipeline as an example, this paper uses Fluent software to establish the leakage model of the gas pipeline and fan model in the tunnel and analyzes the influence of different fan locations and number of fans on gas concentration. It can be concluded that: (1) the use of press-in method makes it more efficient to discharge gas out of the tunnel. (2) In order to make ventilation efficient, the fan should be arranged in a higher position and needs to be at a distance from the top of the tunnel. (3) Parallel use of two fans has better ventilation effect than single fan.

The aim of this publication is to analyze the topic of high-frequency jet ventilation (HFJV), namely the catheter HFJV (C-HFJV) from a mathematical-physical as well as a clinical point of view. There are known issues with applying anesthesia and artificial lung ventilation (ALV) during surgical procedures in the upper airways, e.g. during bronchoscopy or tracheostomy. The principles, advantages, and disadvantages of HFJV are discussed in context with basic physical principles to clarify the proper use of this method. The basic technical principles of catheter construction, as well as its functional properties from a biophysical point of view, are introduced. Also, the placement of the catheter in the airways, the set-up of the HFJV ventilator, and the indications as well as the risks and contraindications of the use of C-HFJV are analyzed. This leads to the explanation of potentially optimal techniques for C-HFJV applications. In this article, we present the positive effects of C-HFJV even with complications such as bacterial or viral pneumonia, including COVID-19. In conclusion, we offer recommendations for clinical practice obtained from a literature review as well as from our own rich clinical experience.

Cystic echinococcosis (CE), caused by the larval stage of Echinococcus granulosus, is significantly underreported in Mongolia due to geographical remoteness, lack of early diagnostics, and poor clinical management. This study aimed to provide a more accurate estimate of CE in Mongolia by comparing data of surgical (reported) and diagnosed (unreported) cases, and assessing the challenges faced by rural doctors in disease management and surveillance. We collected data on surgical cases hospitalized between 2006-2016 and newly diagnosed CE cases in 2016 from eight provinces. Using a quasi-Poisson regression model of the collected data, we used extrapolation to estimate the number of diagnosed cases for the entire country. Additionally, fourty health professionals from all 21 provinces rated local clinical management for CE through a questionnaire. Results reveal that surgical cases (2.2 per year) represent only one-eighth of diagnosed cases (15.9 per year). The laboratory facilities, disease reporting, and cyst classification usage scored below 2. These results highlight the significant underreporting of CE in Mongolia and urges human and animal health experts, along with policymakers, to invest into combating CE, particularly in remote provincial areas. It also emphasizes the need for standard clinical management involving cyst classification according to WHO-IWGE, seamless integration of CE reporting and monitoring mechanisms, which can significantly contribute to the national and global burden estimation of CE.

Despite polycarbonate (PC) being a widely used engineering plastic, its notch and crack sensitivity pose challenges in critical applications. To address this, PC was blended with elastomeric polymers to explore the improvement in toughness. This study systematically investigates the toughening mechanisms of PC blended with acrylonitrile-butadiene-styrene (ABS), copolyether ester elas-tomer (COPE), and ABS and styrene-ethylene-butylene-styrene (SEBS) copolymer grafted with maleic anhydride (MA). The morphology and mechanical behavior were evaluated under qua-si-static and high-speed tensile tests and Charpy impact tests using optical, electronic, and atomic force microscopy and Raman spectroscopy. The morphological analysis reveals cavitation and crazing phenomena for COPE and SEBS-g-MA systems, and mostly debonding for ABS, indicating an improvement in toughening. While the addition of ABS improves the PC plastic deformation, modifying ABS with maleic anhydride enhances the elastic modulus. Blending PC with SEBS-g-MA increases the strain at break, and the addition of COPE significantly improves the deformation behavior of PC (by around 115%). This comparative study provides valuable insights into the performance of different PC-elastomer blends under similar conditions, supporting the selection of appropriate materials for given applications.

Ventilation in cities is crucial for the well being of their inhabitants. Therefore, local governments require air ventilation assessments (AVAs) prior to the construction of new buildings. In a standard AVA, however, only neutral stratification is considered, although diabatic and particularly unstable conditions may be observed more frequently in nature. The results presented here indicate significant changes in ventilation within most of the area of Kowloon City, Hong Kong, included in the study. A new definition for calculating ventilation was introduced, and used to compare the influence of buildings on ventilation under conditions of neutral and unstable stratification. The overall ventilation increased due to enhanced vertical mixing. In the vicinity of exposed buildings, however, ventilation was weaker for unstable stratification than for neutral stratification. The influence on ventilation by building parameters, such as the plan area index, was altered when unstable stratification was considered. Consequently, differences in stratification were shown to have marked effects on ventilation estimates, which should be taken into consideration in future AVAs.

The Foreign Exchange rate is very much crucial for determining the economic health level of the country. The foreign exchange rate provides financial stability, enhances purchasing power and allows global trades. This rate usually fluctuates due to the market forces which control the supply and demand of the currency. Nominal and relative inflation and income level have a substantial effect on determining the exchange rates. Government measures, international situations, natural disasters or any unexpected situation like Covid-19, Rohingya crisis etc. can affect the exchange rates. Besides this, the interaction between the factors can create different reasoning to affect the market. This study tries to identify some factors with relevant examples.

In the past two decades, acoustic metamaterials have garnered much attention owing to their unique functional characteristics, which is difficult to be found in naturally available materials. The acoustic metamaterials have demonstrated to exhibit excellent acoustical characteristics that paved a new pathway for researchers to develop effective solutions for a wide variety of multifunctional applications such as low-frequency sound attenuation, sound wave manipulation, energy harvesting, acoustic focusing, acoustic cloaking, biomedical acoustics, and topological acoustics. This review provides an update on the acoustic metamaterials' recent progress for simultaneous sound attenuation and air ventilation performances. Several variants of acoustic metamaterials, such as locally resonant structures, space-coiling, holey and labyrinthine metamaterials, and Fano resonant materials, are discussed briefly. Finally, the current challenges and future outlook in this emerging field is discussed as well.

The high prevalence of human papillomavirus (HPV) infection in oropharyngeal squamous cell carcinoma (OPSCC) is well-established, with p16 expression being a strong predictor. HPV-related tumors exhibit unique mechanisms targeting p16 and p53 proteins. However, re-search on HPV prevalence and the combined predictive value of p16 and p53 expression in head and neck cutaneous squamous cell carcinomas (HNCSCC), especially in Asian populations, is limited. This retrospective study surveyed 62 HNCSCC patients (2011–2020), excluding those with facial warts or other skin cancers. All patients underwent wide excision and biopsy. Immuno-histochemical staining for HPV, p16, and p53 yielded both positive and negative results. The relevance of each marker was investigated by categorizing the tumor locations into high-risk (Area H) and mid-risk (Area M) zones based on recurrence frequency. Of the 62 patients, 20 (32.26%) were male, with an average age of 82.27 years (26–103). Area H included 19 cases (30.65%), with the eyelid and lip being the most common sites (five cases, 8.06%). Area M in-cluded 43 cases (69.35%), with the cheek being the most common site (29 cases, 46.77%). p16 ex-pression was positive in 24 patients (38.71%), p53 expression in 42 patients (72.58%), and HPV in five patients (8.06%). No significant association was found between p16 expression and HPV presence (p > 0.99), with a positive predictive value of 8.33%. This indicates that p16, a surrogate marker of HPV in OPSCC, is not a reliable marker for HPV in HNCSCC. This study enhances our understanding of the relationship between HPV, p53, and p16 in HNCSCC in Asian populations and offers valuable insights for further research.

The COVID-19 pandemic has significantly impacted human health and daily life. Meteorological factors play a crucial role in virus transmission. Understanding these factors is critical for pandemic control, yet debates continue due to variations in research methods and data. This study uses a global dataset and focuses on administrative units smaller than 10,000 km². The relationship between daily COVID-19 incidence rates and meteorological factors—including temperature, relative humidity (RH), ultraviolet radiation (UVR), and diurnal temperature range (DTR)—was analyzed across 173 units in 62 countries. The results revealed significant nonlinear responses and lag effects between incidence rates and the meteorological factors. Key inflection points were observed at 0°C and 24°C for temperature, 63% for RH, 102 KJ/m² for UVR, and 15°C for DTR. Below 0°C, infection risk increased with rising temperatures; from 0°C to 24°C, risk decreased; and above 24°C, risk escalated rapidly. RH below 63% correlated inversely with infection risk, while above 63%, the correlation was positive. Infection risk decreased with UVR below 102 KJ/m² but increased beyond this threshold. These nonlinear responses are primarily driven by the differential effects of these factors on virus survival, transmission, and human immunity. Conditions around 24°C, 63% RH, 102 KJ/m² UVR, and DTR below 15°C appear optimal for human immunity, correlating with lower infection risk. High temperature and low UVR prompted immediate infection responses, while low temperatures, high UVR, and larger DTR showed delayed effects. These findings provide new, more reliable evidence for understanding the mechanisms driving COVID-19 pandemic dynamics and for preventing the future normalization of the epidemic.

Outbreaks of the crown-of-thorns seastar (CoTS) represent a major cause of coral loss on the Great Barrier Reef. Outbreaks might be explained by enhanced larval survival supported by higher phytoplankton availability after flood events, yet little is known about CoTS larvae feeding behaviour, in particular their potential for selective feeding. Here, single- and mixed-species feeding experiments were conducted on CoTS bipinnaria larvae using five algae (Phaeodactylum tricornutum, Pavlova lutheri, Tisochrysis lutea , Dunaliella sp. and Chaetoceros sp.) and two algal concentrations (1000 and 2500 algae mL^-1). Cell counts using flow-cytometry at the beginning and end of each incubation experiment allowed us to calculate the filtration and ingestion rates of each species by CoTS larvae. In line with previous studies, CoTS larvae ingested more algae when initial algal concentration was higher. We found evidence for the selective ingestion of some species (Chaetoceros sp., Dunaliella sp.) over others (P. lutheri, P. tricornutum). The preferred algal species had the highest energy content, suggesting that CoTS selectively ingested the most energetic algae. Ultimately, combining these results with spatio-temporal patterns in phytoplankton communities will help elucidate the role of larval feeding behaviour in determining the frequency and magnitude of CoTS outbreaks.

Background/Objectives: Airway management techniques, including mask ventilation and tracheal intubation, are vital across medical settings. However, these procedures can be challenging, especially when environmental conditions are less than ideal. This study explores how the height of the operating table affects the difficulty of surgical procedures involving mask ventilation and tracheal intubation. Methods: Twenty anesthesiologists participated in this study. We assessed the difficulty of procedures- such as mask ventilation, Macintosh laryngoscopy, and video laryngoscopy with McGRATH and AWS- on a four-level scale. The operating table’s height was adjusted at four points: operator's umbilicus, inferior margin of the 12th rib, xiphoid process, and nipple. Results: Mask ventilation was easiest at the operating table’s height aligned with the inferior margin of the 12th rib. Conversely, direct laryngoscopic exposure was perceived easier at higher table heights, with nipple height being optimal. McGRATH laryngoscopy showed consistent difficulty across table height, whereas AWS tended to be somewhat more difficult at greater heights. Conclusions: The optimal bed height for video laryngoscopy coincided with that for mask ventilation. Video laryngoscopy offers enhanced flexibility in optimal patient positioning compared to Macintosh laryngoscopy, contributing to its advantages in tracheal intubation procedures.

We report the case of a 44-year-old woman who suffered gastric perforation after receiving bag-valve-mask (BVM) ventilation in the setting of alcohol intoxication. She had a markedly distended abdomen and cold, dusky lower extremities upon arrival to the emergency department. Imaging revealed a large volume intraabdominal accumulation of air with compression of the aorta. Needle decompression relieved symptoms of lower extremity arterial insufficiency. However, the patient quickly decompensated and subsequent exploratory laparotomy confirmed gastric rupture. A subtotal gastrectomy was performed but the patient ultimately passed on post-operative day two due to multi-organ dysfunction. Although BVM ventilation is commonplace in both the hospital and field, there is a lack of awareness of the serious complications of abdominal air accumulation due to their rareness in the adult population. Checking for abdominal distention during resuscitation ought to be routine in all patients. Signs of arterial insufficiency accompanying abdominal distention, once confirmed by diagnostic imaging that shows extensive pneumoperitoneum, are indicators of having reached a life-threatening level of air accumulation, calling for immediate needle decompression and exploratory laparotomy.

Fire behavior of natural rubber latex foam under different thickness conditions(d=1,2and 5cm)were explored though a little of experiments by using the self-built small scale experimental platform. It can be shown that the flame spread law of thermally thin and thermally thickness are different. Natural rubber latex foam with thickness of 2cm show higher fire risk, which value of flame spread rate, maximum flame height, maximum mass loss rate and maximum temperature is 0.00293m/s, 851.875mm, 1.83g/s, 948K,repectively.That may because the thickness of residue formed of thermally thick materials is larger than the thin one, obstructing the contact of the natural rubber latex foam with fresh air .In addition, a special phenomenon is noticed that during the second stage, the bottom unburned zone located in the four edges(thermally thin material) and middle player(thermally thick material).

In this paper thermo-mechanical behavior of 4D printed Polylactic Acid (PLA) was investigated, focusing on its response to varying strain rates and temperatures below the glass transition temperature. Dynamic mechanical analysis and uniaxial tensile tests confirmed PLA's dependency on strain rate, showcasing its sensitivity to external stimuli. Stress-strain curves exhibited typical thermoplastic behavior, with yield stresses varying with strain rates, underscoring PLA's responsiveness to different deformation speeds. Clear strain rate dependence was observed, particularly at quasi-static rates, with temperature and strain rate fluctuations significantly influencing PLA's mechanical properties, including yield stress and deformation behavior. Isothermal compression tests demonstrated predictable stress-strain curves with distinct yield points, while adiabatic tests reveal additional complexities such as heat accumulation leading to further softening. Thermal imaging revealed temperature increase during deformation, highlighting the material's thermo-sensitive nature. These findings provide the basis for future research with the focus on advanced modeling techniques and mitigation strategies for self-heating effects, aiming to enhance PLA-based product reliability and performance in applications with deformations at higher strain rates, while also developing models to simulate shape recovery in 4D printed PLA structures at both cold and hot programming temperatures.

The formulation and analytic solution of a new mathematical model with constitutive curvature for analysis of tunnel ventilation shaft wall is proposed. Based on the Mindlin-Reissner theory for thick shells, this model also takes into account the shell constitutive curvature and considers an expression of the shear correction factor variable (αn) in terms of the thickness (h) and the radius of curvature (R). The main advantage of the proposed model is that it has the possibility to analyze thin, medium and thick tunnel ventilation shafts. As a result, two comparisons were made: the first one, between the new model and the Mindlin-Reissner model without constitutive curvature with the shear correction factor (α_n=6/5) as a constant, and the other, between the new model and the tridimensional numerical models (solids and shells) obtained by finite element method for different slenderness ratios (h/R). The limitation of the proposed model is that it is to be formulated for a general linear-elastic and axial-symmetrical state with continuous distribution of the mass.

This paper presents a methodology for determining the sensitivity of the main air flow directions in ventilation subnetworks to changes of aerodynamic resistance and of air density in mine workings. Formulae for determination of the sensitivity of the main subnetwork air flows by establishing the degree of dependency of the air volume stream in a given working on the variations in resistance or air density of other workings of the network have been developed. They have been implemented in the VentGraph mine ventilation network simulator. This software, widely used in Polish collieries provides an extended possibility to predict the process of ventilation, air distribution and, in the case of underground fire, also the spread of combustion gasses. The new method facilitates assessment by mine ventilation services of the stability of ventilation systems in exploitation areas and determine of the sensitivity of the main subnetwork air flow directions to changes of aerodynamic resistance and air density. Recently in some Polish collieries new longwalls are developed in seams located deeper then the bottom of the intake shaft. Such solution is called “exploitation below the level of access” or “sublevel”. The new approach may be applied to such developments to assess the potential of changes of direction and air flow rates. In addition, interpretation of the developed sensitivity indicator is presented. While analyzing air distributions for sublevel exploitation, application of current numerical models for calculations of the distribution results in tangible benefits, such as the evaluation of the safety or risk levels for such exploitation. Application of the VentGraph computer program, and particularly the module POŻAR (fire) with the newly developed options, enables an additional approach to the sensitivity indicator in evaluating air flow safety levels for the risks present during exploitation below the level of the intake shaft. The analyses performed and examples presented enabled useful conclusions in mining practice to be drawn.

Innovative interventions in the planning and design of stair and escalator facilities call for understanding their effects on stair use. This study considers five planning variables for the twinned stair and escalator facilities–stair pitch and width, angle of deviation, height and separating distance. Public sites were identified in 8 commercial districts in Beijing. Facilities (n=21) presenting heterogeneously across variables were sampled for simultaneous up and down pedestrian counts in 18 5-minute video segments middays, for a total of 1464 counts. Stair width accounts for 20% of the variance in ascending rate and 10% in descending. Plan angle accounts for 2% in ascending and 5% in descending, while pitch accounts for 1% in ascending and 5% in descending. The study confirms the effects of layout and design of stairway and escalator facilities on facility choice. The results point directly to interventions in support of higher stair-climbing rates.

Based on a rich data set of recoveries donated by a debt collection business, recovery rates for non-performing loans taken from a single European country are modelled using linear regression, linear regression with Lasso, beta regression and inflated beta regression. We also propose a two-stage model: beta mixture model combined with a logistic regression model. The proposed model allows us to model the multimodal distribution we find for these recovery rates. All models are built using loan characteristics, default data and collections data prior to purchase by the debt collection business. The intended use of the models is to estimate future recovery rates for improved risk assessment, capital requirement calculations and bad debt management. They are compared using a range of quantitative performance measures under K-fold cross validation. Among all the models, we find that the proposed two-stage beta mixture model performs best.

With opioid overdose rates on the rise, we aim to develop a county-level risk stratification, specifically focusing on access to Medications for Opioid Use Disorder (MOUD) and high overdose rates. We examined over 15 million records from the South Carolina Prescription Tracking System (SCRIPTS) across 46 counties. Additionally, we incorporated data from opioid treatment programs, healthcare professionals prescribing naltrexone, clinicians with buprenorphine waivers, and county-level overdose fatality statistics. To assess the risk of opioid misuse, we classified counties into high-risk and low-risk categories based on prescription rates, overdose fatalities, and treatment service availability. Utilizing statistical methods, we compared prescription patterns and outcomes between these groups. Our study shows that between 2017 and 2021, opioid prescriptions decreased from 64,223 to 41,214 per 100,000 residents, while fentanyl-related overdose deaths increased by 312%. High-risk counties have significantly higher rates of fentanyl prescriptions and rely more on out-of-state doctors. They also exhibit higher instances of doctor shopping and had fewer medical doctors per capita, with limited access to MOUD. To effectively combat the opioid crisis, we advocate for improved local healthcare infrastructure, broader treatment access, stricter management of out-of-state prescriptions, and vigilant tracking of prescription patterns. Tailored local strategies are essential for mitigating the opioid epidemic in these communities.

A growing number of studies suggest that SARS-CoV-2 could interfere with homeostatic mechanisms in the lung but the implications of this possible interference have not been fully explored in the literature. In this work, we examine the consequences that can be drawn from this hypothesis according to currently available knowledge. We suggest that one such consequence is the potential disruption of normal ventilation and perfusion of lung regions that may be distant from the infection sites. Loss of ventilation might result in local alveolar hypoxia and contribute to hypoxemia, which in turn could trigger homeostatic responses that enhance blood oxygenation by redistributing pulmonary blood circulation. Sudden changes in perfusion might then lead to the development of hydrostatic edema and eventually to vascular remodeling and inflammation. Therefore, the immune response might not be the only source of the substantial inflammation observed in lung tissues of patients with severe COVID-19, as is often assumed in the literature. The balance between the homeostatic and the immune reaction in each patient could account for the observed heterogeneity of the clinical manifestations of COVID-19.

Although extracorporeal membrane ventilation offers the possibility for low frequency ventilation, protocols commonly used in patients with acute respiratory distress syndrome (ARDS) and treated with extracorporeal membrane oxygenation (ECMO) vary largely. Whether strict adherence to low frequency ventilation offers benefit on important outcome measures is poorly understood. Background/Objectives: This pilot clinical study investigated the efficacy of low frequency ventilation on ventilator free days (VFDs) in patients suffering from ARDS treated with ECMO therapy. Methods: In this single-center randomized controlled trial, 44 (70% male) successive ARDS patients treated with ECMO (aged 56 ± 12 years, SAPS III 64 (SD ± 14)) were randomly assigned 1:1 to control group (conventional ventilation) or treatment group (low fre-quency ventilation during first 72 hours on ECMO: respiratory rate 4-5/min; PEEP 14-16cm H2O; plateau pressure 23-25 cm H2O, tidal volume: < 4mL/kg). The primary endpoint was VFDs at day 28 of ECMO start. The major secondary endpoint was ICU mortality, 28-day and 90-day mortality. Results Twenty-three (52%) patients could be successfully weaned from ECMO and were discharged from intensive care unit (ICU). Twelve patients in the treatment group and five patients in the control group showed more than one VFD at day 28 after ECMO. VFDs were 3.0 (SD ± 5.5) days in the control group and 5.4 (SD ± 6) days in the treatment group (P = 0.117). Until day 28 after ECMO initiation, patients in the treatment group could be more often successfully weaned from ventilator (OR of 0.164 of 0 VFDs at day 28 after ECMO start; 95% CI 0.036-0.758; P = 0.021). ICU mortality did not differ significantly (36% in treatment group and 59% in control group; P = 0.227). Conclusions: Low frequency ventilation is comparable to conventional protec-tive ventilation in patients with ARDS treated with ECMO. However, low frequency ventilation may support weaning from invasive mechanical ventilation in patients suffering from ARDS treated with ECMO therapy.

Mechanical ventilation systems used in houses are designed to reduce carbon dioxide emissions while minimizing the energy loss resulting from ventilation. However, increase in indoor fine particulate (PM2.5) concentration because of external PM2.5, influx through the ventilation system poses a problem. In this study, we analyzed the changes in indoor PM2.5 concentrations via dis-tinguishing between cases of high and low outdoor PM2.5 concentrations, considering the effi-ciency of filters used in residential mechanical ventilation systems. When using minimum effi-ciency reporting value (MERV) 10 filters in the ventilation system, the outdoor PM2.5 concentra-tion was 5 μg/m³; the indoor PM2.5 concentration became 73% after 60 min compared to the ini-tial. When the outdoor PM2.5 concentration was 30–40 μg/m³, the indoor PM2.5 concentration reached 91%. However, when MERV 13 filters were used, the indoor PM2.5 concentration con-sistently dropped to 73–76% regardless of the outdoor PM2.5 concentration. Furthermore, by comparing the established equation with the mass-balance model, the error was confirmed to be within 5%, indicating good fit. This allows the prediction of indoor PM2.5 under various condi-tions when using mechanical ventilation systems, enabling the formulation of strategies to maintain indoor PM2.5 as recommended by the World Health Organization.

The objective of the study was to evaluate the risk factors associated with lower COVID-19 vaccination rates in the United States. The study evaluated the effect of red-blue political affiliation and the effect of the US state's average educational aptitude score and per capita income on states' vaccination rates. The study found that states with concomitantly lower income along with lower educational aptitude scores are less vaccinated while the states with higher income have higher vaccination rates even among those with lower educational aptitude scores. These findings stayed significant after adjusting for red-blue political affiliation where states with red political affiliation have lower vaccination rates. Further study is needed to evaluate how to stop online misinformation among states with low income and low educational aptitude scores; and whether such an effort will increase overall vaccination rates in the United States.

(1) Background: In nervous system information is conveyed by a sequence of action potentials, called spikes-trains. As MacKay and McCulloch proposed, spike-trains can be represented as bits sequences coming from Information Sources. Previously, we studied relations between Information Transmission Rates (ITR) carried out by the spikes, their correlations, and frequencies. Here, we concentrate on the problem of how spikes fluctuations affect ITR. (2) Methods: The Information Theory Method developed by Shannon is applied. Information Sources are modeled as stationary stochastic processes. We assume such sources as two states Markov processes. As a spike-trains' fluctuation measure, we consider the Standard Deviation sigma, which, in fact, measures average fluctuation of spikes around the average spike frequency. (3) Results: We found that character of ITR and signal fluctuations relation strongly depends on the parameter s which is a sum of transitions probabilities from no spike state to spike state and vice versa. It turned out that for smaller s (s<1) the quotient ITR\sigma has a maximum and can tend to zero depending on transition probabilities. While for s large enough (1<s) the ITR\sigma is separated from 0 for each s. Similar behavior was observed also when we replaced Shannon entropy terms in Markov entropy formula by their approximation with polynomials. We also show that the ITR quotient by Variance behaves in a completely different way. (4) Conclusions: Our results show that for large transition parameter s the Information Transmission Rate by sigma will never decrease to zero. Specifically, for 1<s<1.7 the ITR will be always, independently on transition probabilities which form this s, above the level of fluctuations, i.e. in this case we have sigma<ITR. Thus, we conclude that in a more noisy environment, to get appropriate reliability and efficiency of transmission, Information Sources with higher tendency of transition from the state no spike to spike state and vice versa should be applied.

Ventilation in prone position (PP) for 12 to 16 hours per day improves survival in ARDS. However, the optimal duration of the intervention is unknown. We performed a prospective observational study to compare the efficacy and safety of a prolonged PP protocol with conventional prone ventilation in COVID-19-associated ARDS. Prone position was undertaken if P/F <150 with FiO2>0.6 and PEEP>10cmH2O. Oxygenation parameters and respiratory mechanics were recorded before the first PP cycle, at the end of PP cycle and 4 hours after supination. We included 63 consecutive intubated patients with mean age 63.5 years. Of them, 37 (58.7%) underwent prolonged prone position (PPP group) and 26 (41.3%) standard prone position (SPP group). Median cycle duration for SPP group was 20 hrs and for PPP group 46 hrs (p<0.001). No significant differences in oxygenation, respiratory mechanics, number of PP cycles and rate of complications were observed between groups. The 28-day survival was 78.4% in the PPP group versus 65.4% in the SPP group (p=0.253). Extending the duration of PP was as safe and efficacious as conventional PP, but did not confer any survival benefit in a cohort of patients with severe ARDS due to COVID-19.

In recent years, excessive heat in the urban texture has become the main problem in the humid and calm wind city of Babolsar with high density, especially in high-rise areas. Therefore, in order to create comfort in this region, it is necessary to establish and continue the wind circulation in space with an environmentally compatible and optimal configuration. The study applies combination of literature, field measurement, experimental validation of CFD simulation output, and comparative analysis. After field measurement and validation of FLOW-3D simulation software (V11.2.2), the relationship between these parameters (height, the width of passages, enclosure between buildings, and buildings' orientation) will be studied which affects the wind’s velocity and direction. The factors of the buildings' orientation and enclosure based on the passages' width have opposite reactions in the direction of the prevailing wind especially from perpendicular side. In this study, two effective factors are on wind velocity: 1- The orientation of the buildings towards the wind flow by creating permeability 2- Reducing the enclosure by increasing the width of the passage's perpendicular to the wind flow (w '= 3w, E' = 0.33E). According to the theoretical and practical study, first, the creation of permeability in the body of the block and the separation of buildings instead of aggregation has been studied, and then reducing the confinement of streets perpendicular to the wind flow has been discussed as effective solutions to improve the wind velocity and circulation between the urban environment.

The COVID-19 pandemic was associated with increases in some healthcare-associated infections. We investigated the impact of the pandemic on rates and molecular epidemiology of Clostridioides difficile infection (CDI) within one VA Hospital. We anticipated that the potential widespread use of antibiotics for pneumonia during the pandemic might increase CDI rates given that antibiotics are a major risk for CDI. Hospital data on patients with CDI and recurrent CDI (rCDI) were reviewed pre-COVID-19 pandemic (2015 to 2019) and during the pandemic (2020 - 2021). Restriction endonuclease analysis (REA) strain typing was performed on CD isolates recovered from stool samples collected from 10/2019 – 3/2022. CDI case numbers declined 43.2% in 2020 – 2021 compared to the annual mean over the previous 5 years. Stool test positivity rate was also lower during the COVID-19 pandemic (14.3% vs. 17.2%; P = 0.013). Although inpatient volume declined, rates of CDI among inpatients were reduced by 34.2% in 2020 – 2021. Mean monthly cases of rCDI also declined significantly after 2020 [3.38 (95% CI: 2.89 – 3.87) vs. 1.92 (95% CI: 1.27 – 2.56); P = &lt;0.01]. Prior to the pandemic, REA group Y was the most prevalent CD strain among the major REA groups (27.3%). During the first wave of the pandemic from March 8, 2020, through June 30, 2020, there was an increase in the relative incidence of REA group BI (26.7% vs. 9.1%. After adjusting for CDI risk factors, a multivariable logistic regression model revealed that odds of developing an REA group BI CDI increased during the first pandemic wave (OR 6.41, 95% CI: 1.03 – 39.91) compared to the pre-pandemic period. In conclusion, the incidence of CDI and rCDI decreased significantly during the initial waves of the COVID-19 pandemic. In contrast, REA BI (Ribotype 027), a virulent, previously epidemic CD strain and frequently associated with hospital transmission and outbreaks, reappeared as a prevalent strain during the first wave of the pandemic.

The COVID-19 pandemic has emphasized the crucial role of ventilation systems in mitigating cross-infections, especially in infectious disease hospitals. This study introduces a dual-design operation ventilation system that can operate under two sets of ventilation conditions for normal and epidemic times. A challenge is optimizing duct diameters for required airflow while maintaining hydraulic balance. We design a genetic algorithm with adaptive penalty factor, the velocity constraint and the improved crossover and mutation probability. The improved genetic algorithm is suitable for ventilation system networks, which can find a better air duct diameters combination to improve the hydraulic balance rate, and reduce the usage of air valves, resulting in efficient hydraulic balancing commissioning. Compared with the traditional genetic algorithm, it has a faster search speed and a better global search ability, which is effective for the optimal design of ventilation system networks.

The data from the extended system was recorded on-going basis in the archives of the monitoring system, and the multipoint system was directly stored in the methane-anemometers, which allows one to perform a comparative analysis of the obtained records from many methane detectors. An important element of the analyses was the simultaneous registration of the methane concentration in the longwall, together with information on operating time, direction of shearer operation and type of work: mining/cleaning. Mining practice shows that in methane coal mines, methane is often the basic limitation for modern and high-efficiency longwall complexes. The paper reports on selected observations and tests carried out in the Cw-4 longwall in seam 364/2 of the Budryk mine belonging to JSW SA. In observation of the methane level in the Cw-4 longwall, additional sensors installed in the end part of the longwall from the side of the gobs and registration of air velocity and methane concentration in the multipoint system built in the selected longwall cross-section were used, regardless of the air parameters recorded in the monitoring system.

Turbine generator operates with complex cooling system due to the challenge in controlling the peak temperature of the stator bar caused by ohm loss, which is unavoidable. Therefore, it is important to characterise and quantifies the thermal performance of the cooling system. The focus of the present research is to investigate the heat transfer and pressure loss characteristics of typical cooling system, so-called stator ventilation duct. A real scale model was built at its operating conditions for the present study. The direction of cooling air is varied to consider its operation condition, so that there are (1) outward flow and (2) inward flow cases. In addition, the effect of (3) cross flow (inward with cross flow case) is also studied. The transient heat transfer method using thermochromic liquid crystals is implemented to measure full surface heat transfer distribution. A series of Computational Fluid Dynamics analysis is also conducted to support the observation from the experiment. For the inward flow case, the results suggest that the average Nusselt number of the 2nd duct is about 30% higher than the 3rd duct. The trend is similar with the effect of cross flow. The CFD results are in good agreement with the experimental data.

The temporal evolution of pandemics described by the susceptible-infectious-recovered (SIR)-compartment model is sensitively determined by the time dependence of the infection (a(t)) and recovery (u(t)) rates regulating the transitions from the susceptible to the infected and from the infected to the recovered compartment, respectively. Here approximated SIR-solutions for different time dependencies of the infection and recovery rates are derived which are based on the adiabatic approximation assuming time-dependent ratios k(t)=u(t)/a(t) varying slowly in comparison to the typical time characteristics of the pandemic wave. For such slow variations the available analytical approximations from the KSSIR-model, valid for a stationary value of the ratio k, are used to insert a-posteriori the adopted time-dependent ratio of the two rates. Instead of investigating endless different combinations of the time dependencies of the two rates a(t) and u(t) a suitably parameterized reduced time dependence of the ratio k(tau) is adopted. Together with the definition of the reduced time this parameterized ratio k(tau) allows us to cover a great variety of different time dependencies of the infection and recovery rates. The agreement between the solutions from the adiabatic approximation in its four different studied variants and the exact numerical solutions of the SIR-equations is remarkably good providing strong confidence in the accuracy of the proposed adiabatic approximation.

Currently available data are consistent with increased severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) replication at temperatures encountered in the upper airways (25–33°C when breathing room temperature air, 25°C) compared to those in the lower airways (37°C). One factor that may contribute to more rapid viral growth in the upper airways is the exponential increase in SARS-CoV-2 stability that occurs with reductions in temperature, as measured in vitro. Because SARS-CoV-2 frequently initiates infection in the upper airways before spreading through the body, increased upper airway viral growth early in the disease course may result in more rapid progression of disease and potentially contribute to more severe outcomes. Similarly, higher SARS-CoV-2 viral titer in the upper airways likely supports more efficient transmission. Conversely, the possible significance of air temperature to upper airway viral growth suggests that prolonged delivery of heated air might represent a preventative measure and prophylactic treatment for coronavirus disease 2019.

This study examines the causal relationships between interest rates in the Korean financial market using a vector error correction model (VECM) and a Bayesian network. The Bayesian network, a novel approach in this context, identifies two distinct transmission channels: one led by call rates (reflecting monetary policy) and another by 10-year Treasury bond yields (reflecting fiscal policy). While the call rate channel aligns with traditional views, affecting bank lending rates, corporate bond spreads, and commercial paper rates, the 10-year Treasury yield channel highlights a separate fiscal policy transmission mechanism, influencing commercial paper rates indirectly through 30-year Treasury yields and directly impacting merchant bank lending rates. This finding suggests that fiscal intervention could potentially interfere with monetary policy, emphasizing the need for coordinated macroeconomic policy measures. The study also emphasizes the role of 10-year Treasury bonds as a benchmark in the Korean bond market, reflecting medium- to long-term economic outlooks and serving as the underlying asset for various derivatives.

Background. It is well established that human milk feeding contributes in limiting lung disease among vulnerable neonates. The primary aim of this research was to compare the need for mechanical ventilation of human milk-fed sick neonates with that of formula-fed sick neonates. Methods. All late preterm and full term infants from a single center with findings of sepsis, from 2002 to 2017, were identified. Data regarding infant feeding during hospital admission were recorded. Multivariate logistic regression analyses were performed to assess the impact of the type of milk on ventilation support and main neonatal morbidities. Results. The total number of participants was 322 (human milk group = 260, exclusive formula group = 62). On bivariate analysis, 72% of human milk-fed neonates did not need oxygen therapy nor respiratory support versus 55% of their formula-fed counterparts (P<0.0001). Accordingly, invasive mechanical ventilation was required by 9.2% of human milk-fed infants versus 32% of their formula-fed counterparts (P=0.0085). These results hold true in multivariate analysis, indeed human milk-fed neonates were more likely to require less respiratory support (OR=0.44; 95% CI: 0.22, 0.89) when compared to those who were exclusively formula-fed. Conclusion. Human milk feeding might minimize exposure to mechanical ventilation.

This case study investigates the effects of ventilation intervention on measured and perceived indoor air quality (IAQ) in a repaired school where occupants reported IAQ problems. Occupants´ symptoms were suspected to be related to the impurities leaked indoors through the building envelope. The study’s aim was to determine whether a positive pressure of 5-7 Pa prevents the infiltration of harmful chemical and microbiological agents from structures, thus decreasing symptoms and discomfort. Ventilation intervention was conducted in a building section comprising 12 classrooms and was completed with IAQ measurements and occupants´ questionnaires. After intervention, the concentration of total volatile organic compounds (TVOC) and fine particulate matter (PM_2.5) decreased, and occupants´ negative perceptions became more moderate compared to those for other parts of the building. The indoor mycobiota differed in species composition from the outdoor mycobiota, and changed remarkably with the intervention, indicating that some species may have emanated from an indoor source before the intervention.

Our investigations show that electrochemical corrosion of copper is faster than electrochemical corrosion of aluminium at temperatures below 100oC. Literature data analysis shows that the Al atoms diffuse faster than the Cu atoms at temperatures higher than 475oC, Al rich intermetallic compounds (IMCs) are formed faster in the Cu-Al system, and the Kirkendall plane shifts toward Al side. Electrochemical corrosion occurs due to electric current and due to diffusion. An electronic devise working time, for example, depends on initial copper cover thickness on aluminium wire, connected to the electronic devise, temperature, and volume and dislocation pipe diffusion coefficients, so copper, iron, and aluminium electrochemical corrosion rates are investigated experimentally at room temperature and at temperature 100oC. Intrinsic diffusivities ratios of copper and aluminium at different temperatures and diffusion activation energies in the Cu-Al system are calculated by proposed here methods using literature experimental data. Dislocation pipe and volume diffusion activation energies of pure iron are calculated separately by earlier proposed method using literature experimental data. Aluminium dissolved into NaCl solution as the Al3+ ions at room temperature and at temperature 100oC, iron dissolved into NaCl solution as the Fe2+ (not Fe3+) ions at room temperature and at temperature 100oC, copper dissolved into NaCl solution as the Cu+ ions at room temperature and as the Cu+ and the Cu2+ ions at temperature 100oC. It is founded experimentally that copper corrosion is higher than aluminium corrosion, and ratio of electrochemical corrosion rates, kCu/kAl>1, decreases with temperature increasing, although iron electrochemical corrosion rate doesn’t depend on temperature below 100oC. It is obvious, because melting point of iron is more higher then melting point of copper or aluminium. It is calculated that copper electrochemical corrosion rate is approximately equal to aluminium electrochemical corrosion at temperature about 300oC, so copper can dissolve into NaCl solution mostly as the Cu2+ ions at temperature about 300oC. Ratio of intrinsic diffusivities, DCu/DAl <1, increases with temperature increasing, and intrinsic diffusivity of aluminium could be approximately equal to intrinsic diffusivity of copper at temperature about 460oC.

The aims of study was to evaluate the effects of rates, sources and timing of nitrogen application under cover of transgenic corn yield cultivated in Amazon Biome. The experiments were conducted in Parauapebas city, State of Pará, Brazil, in two years (2016/2017 and 2017/2018). The experimental design was randomized blocks, in a 5x2x2 factorial scheme, consisting of five rates of N (0; 45; 90; 135; and 180 kg ha-1), two nitrogen sources (urea and ammonium sulfate) and two application times of N (phenological stages V4 and V8), with four replications. The factor N rates promoted adjustment of linear equation (leaf area index, mass of thousand grains, and yield) and quadratic equation (dry mass of leaf index). Nitrogen fertilization promoted significant increases in mass of thousand grains and yield, obtaining the best results with 180 kg ha-1 of N applied at V4 phenological stage. Based on results obtained in two years of corn cultivated under conditions of Amazon Biome, the application of N at V4 phenological stage at rates of 121 to 131.39 kg ha-1 of N showed the best results for vegetative growth, while 180 kg ha-1 of N, regardless of source used, urea or ammonium sulfate, promoted greater grain weight and greater yield.

Obesity is treatment-resistant, and is linked with a number of serious, chronic diseases. Adult obesity rates in the United States have tripled since the early 1960s. Recent reviews show that an increased ratio of omega-6 to omega-3 fatty acids contributes to obesity rates by increasing levels of the endocannabinoid signals AEA and 2-AG, overstimulating CB₁R and leading to increased caloric intake, reduced metabolic rates, and weight gain. Cannabis, or THC, also stimulates CB₁R and increases caloric intake during acute exposures. The present meta-analysis reveals significantly reduced body mass index and rates of obesity in Cannabis users, in conjunction with increased caloric intake. We provide for the first time a causative explanation for this paradox, in which rapid and long-lasting downregulation of CB₁R following acute Cannabis consumption reduces energy intake and storage and increases metabolic rates, thus reversing the impact on body mass index of elevated dietary omega-6/omega-3 ratios.

Over the years, researchers have been developing different ventilation strategies as a potential solution for controlling infectious airborne transmissions in healthcare facilities. The effects of ventilation systems on airflow characteristics have been extensively discussed among researchers since SARS-CoV-2 outbreak in 2019. Based on a bibliometric study of 154 publications from 1970 to 2021 retrieved from the Web of Science (WoS) database, this paper examines the research landscape on the effects of ventilation strategies on airflow analysis in healthcare facilities. Results show that China is the most productive country due to its significant contributions to the top prolific authors and funding agencies, which have promoted the research development of the topic. Several research hotspots were identified through keyword co-occurrence analysis. Cluster 1 highlights the ventilation studies involving ventilation layouts and ventilation rates in healthcare facilities. Cluster 2 underlines the computational analysis of ventilation performance for reducing the exposure risk of occupants, which promotes the development of infection control measures. Cluster 3 strengthens the knowledge of the emission and dispersion characteristics of respiratory droplets in healthcare facilities. Overall, this paper highlights the future direction of the current research field other than identifying strategic collaborators and suitable publication outlets for interested researchers.

The COLOSS research association has been assessing honey bee colony losses, associated risk factors and management, focusing on Western countries but with a progressive international expansion. Here, we report the first survey on the loss rates of colonies in 2022/23 in Ethiopia using COLOSS monitoring survey tools. A face-to-face interview questionnaire survey was conducted on 64 beekeepers selected from Oromia and Tigray regions. This covered 1,713 honey bee colonies distributed in 68 apiaries. The percentages of colonies lost were significantly different between Oromia (24.1%) and Tigray (66.4%) regions. Colony losses were attributed as unsolvable queen problems (8% in Oromia; 10% in Tigray), natural disaster (32%; 82%), and empty hives or dead colonies (60%; 8%). The loss rate was significantly affected by queen replacement (p

Although evolutionary theory has yet to furnish a comprehensive rationale for the underlying mechanism of natural selection, it is pertinent to note that the phenomenon transcends the confines of biological systems, exhibiting analogous patterns in physical systems as well. Specifically, isolated and closed systems tend to evolve towards states of progressively increasing entropy. In scenarios where multiple paths for entropy increase are accessible, such systems tend to favor combinations of paths that exhibit the most rapid entropy increase rates. Among the various processes in nature, life activities constitute a salient means of achieving entropy increase. Genetic variation within organisms generates individuals that vary in their rates of entropy increase. As these organisms interact, compete and combine, they form diverse combinations of entropy-increasing pathways. Nature, in turn, selects among these combinations, favoring those that culminate in the fastest entropy increase, thereby propelling the evolution of life. Essentially, the evolution of life is an ongoing exploration of diverse combinations of pathways that maximize entropy increase across various energy pools. Amidst continuous genetic variation and the selective pressure imposed by nature for maximum entropy production rates, information accumulates, leading to a corresponding acceleration in the rate of entropy increase. This natural selection, which favors maximizing the entropy at the fastest possible rate, serves as the ultimate driving force for the origin and evolution of life.

This research article examines the state-wise literacy rates in India, with a focus on male and female literacy, as well as the disparities between them. The data was sourced from a survey conducted by the National Statistical Office (NSO), with a special emphasis on Union Territories and Northeastern states based on the 2011 Census. Kerala boasts the highest literacy rate at 96.2%, while Andhra Pradesh reports the lowest at 66.4%. Notably, the national male-female literacy gap stands at 12.9%. Kerala also demonstrates the smallest gender gap at 2.2%, while Rajasthan exhibits the highest at 23.3%. Through descriptive and explorative analysis, this article provides a comprehensive overview of literacy rates across various Indian states and Union Territories, highlighting the significant disparities that exist.

The hybridization of machine learning methods with soft computing techniques is an essential approach to improve the performance of the prediction models. Hybrid machine learning models, particularly, have gained popularity in the advancement of the high-performance control systems. Higher accuracy and better performance for prediction models of exergy destruction and energy consumption used in the control circuit of heating, ventilation, and air conditioning (HVAC) systems can be highly economical in the industrial scale to save energy. This research proposes two hybrid models of adaptive neuro-fuzzy inference system-particle swarm optimization (ANFIS-PSO), and adaptive neuro-fuzzy inference system-genetic algorithm (ANFIS-GA) for HVAC. The results are further compared with the single ANFIS model. The ANFIS-PSO model with the RMSE of 0.0065, MAE of 0.0028, and R² equal to 0.9999, with a minimum deviation of 0.0691 (KJ/s), outperforms the ANFIS-GA and single ANFIS models.

The determination of critical ventilation flow rate is significant for the risk control and the standard development during accidental hydrogen leakage in a confined space with hydrogen-related equipment. In this paper, an analytical model for calculating critical ventilation flow rate was proposed through the quantification and constraint solution of ventilation effect and ventilation cost. The experimental method was used to investigate the effects of nozzle diameter and stagnation pressure on diffusion and ventilation for horizontal hydrogen leakage in a cuboid chamber. Ventilations from 30m3/h to 180m3/h were carried out through the rectangular vent. It was shown that the peak concentration of the measuring point is positively correlated with the stagnation pressure and the nozzle diameter. The experimental data are used to verify the analytical model by calculating the effective ventilation time. The study demonstrates that the critical ventilation flow rate can be increased significantly at higher stagnation pressures and larger nozzle diameters. And the discrepancy of critical ventilation flow rates under different nozzle diameters will be enhanced with the increase of stagnation pressure. For the stagnation pressure of 0.4MPa, the critical ventilation flow rate under 4mm nozzle even increases by 52% relative to the 2mm nozzle.

Many farms utilize closed-type livestock systems to enhance productivity and facilitate effective environmental management. However, the confined nature of these closed spaces poses an increased risk of exposure to harmful gases and organic dust for both workers and livestock. Additionally, the introduction of outside air through ventilation systems can lead to temperature fluctuations within the breeding environment, resulting in potential productivity issues. This research paper employs computational fluid dynamics (CFD) to develop ventilation operation management plans that address both the working environment and the breeding environment simultaneously. The proposed plans are designed to be easily implemented in practical farm settings. The findings of this study, based on simulation analysis, indicate that while ventilation is effective in reducing harmful gases and improving the working environment, its efficiency decreases after the initial 3 minutes of operation. Furthermore, uncontrolled ventilation can cause sudden temperature changes, which may adversely affect the well-being of the livestock. However, when upgraded ventilation structures are implemented, significant improvements in the working environment (an average of 27.3% improvement) can be achieved while maintaining temperature stability for the livestock. These results highlight the importance of referring to the provided ventilation operation management table before commencing work, as it enables workers to improve the working environment while minimizing the potential impact of ventilation on the breeding environment.

This paper, we examined the technology to maximize the use of renewable energy. The passive ventilation system is expected to reduce the energy consumption of the fan power and the maintenance burden. In addition, the wall-mounted solar air heater can supply thermal energy without using any energy at all. Therefore, we propose a "passive ventilation system with a solar air heater" that combines a passive ventilation system with solar air heater to preheat the air supply and reduce the ventilation load. To evaluate the solar air heater performance in a real environment, we developed a simulation for calculating the heat collection capacity of the solar air heater, and then implemented the system in a real building for verification. Based on the measurement results, the effects of heating load reduction and prediction methods are presented.

Changes in crude oil price affect the shipping freight market in three different channels. This study explores the dependence structure between oil prices and maritime freight rates to identify the strongest channel. Therefore, it investigates the relationship between oil prices and three major maritime freight rates; the Baltic Dry Index (BDI), the Baltic Dirty Tanker Index (BDTI), and the Baltic Clean Tanker Index (BCTI). We employ the decomposition method, not studied in the existing literature. The copula approach identifies the time-varying effects and asymmetry in the tail dependence structure between oil prices and freight rates. The main results of this analysis are as follows. The decomposed components display different conditional dependence patterns, and asymmetry is revealed in the upper and lower tail dependence. In the long run, we find more dependence in extreme periods like the financial crises. In short-run fluctuations, we find the dependence increases in an economic boom. The implications of the results suggest that dependence can vary over time and may change depending on extreme events, implying that the complementary strategies of the long run and short run should be different.

Genus Clematis is one of the largest within Ranunculaceae. Here we report the chloroplast genome of two Clematis species, C. brachyura and C. trichotoma endemic to Korea. The chloroplast genome lengths of C. brachyura and C. trichotoma are 159,532 bp and 159,170 bp, respectively. Gene contents in the complete chloroplast genomes of these two Clematis species are identical to that of most Ranunculaceae and other angiosperms. However, our data results demonstrated that genus Clematis has inversion and rearrangement events concerning gene rps4 gene, rps16 to trnH region, and trnL to ndhC region, and IR regions expansion. Comparison of IR regions among Ranunculaceae species revealed that Clematis species contained six protein coding genes (infA, rps8, rpl14, rpl16, rps3, and rpl22) usually found in the long single copy (LSC) region of other species. Phylogenetic analysis demonstrated that genus Clematis is closely related to genus Ranunculus. Differences in repeat structure, substitution rates, and IR expansion in genera Clematis and Ranunculus, explained their relationship. Clematis species showed slightly higher tandem repeats content than Ranunculus species. The six protein-coding genes showed lower synonymous substitution rates in the IR of Clematis species than in the LSC of Ranunculus species. Overall, the chloroplast genomes and results presented here provide important information on the evolution of Ranunculaceae.

Organisms in the wild have cryptic life stages that are sensitive to changing environmental conditions and can be difficult to survey. In this study, I used mark-recapture methods to repeatedly survey Anaea aidea (Nymphalidae) caterpillars in nature, then modeled caterpillar demography as a hidden Markov process to assess if temporal variability in temperature and density influence the survival and growth of A. aidea over time. Individual encounter histories result from the joint likelihood of being alive and observed in a particular stage, and I included hidden states by separating demography and observations into parallel and independent processes. I constructed a demographic matrix containing the probabilities of all possible fates for each stage, including hidden states, e.g., eggs and pupae. I observed both dead and live caterpillars with high probability. Peak caterpillar abundance attracted multiple predators, and survival of fifth instars declined as per capita predation rate increased through spring. A time lag between predator and prey abundance was likely the cause of improved fifth instar survival estimated at high density. Growth rates showed an increase with temperature, but the most likely model did not include temperature. This work illustrates how state-space models can include unobservable stages and hidden state processes to evaluate how environmental factors influence vital rates of cryptic life stages in the wild.

This study investigates the characteristics of formaldehyde (HCHO) concentration and its reduction in newly constructed apartment buildings in Dubai. It addresses the significant health risks of high HCHO levels due to poor ventilation and extensive use of VOC-emitting materials. The research explores the effectiveness of various mitigation strategies, including air purifiers, photocatalyst applications, and window ventilation, in the living room, master bedroom (MBR), Room 1, and Room 2. HCHO concentrations were measured under different conditions: sealed windows, operation of an air purifier with a VOCs filter, and the application of a photocatalyst. The study followed a quantitative approach, recording real-time HCHO levels over 24 hours. Results indicated that sealing windows led to HCHO concentrations surpassing the domestic standard of 0.1 ppm, with the MBR recording the highest concentration at 0.73 ppm. The air purifier showed minimal impact within the first 8 hours but achieved an 18% reduction after 24 hours of operation. Applying a photocatalyst to room surfaces resulted in a 50% reduction in HCHO levels. Ventilation through window openings significantly improved air exchange rates, with the air exchange per hour (ACH) increasing proportionally with window opening size. Smaller rooms with larger window-to-volume ratios, such as Room 1 and Room 2, maintained HCHO concentrations below the WHO standard of 0.1 ppm with partial window openings. The study concludes that window ventilation is the most effective strategy for reducing HCHO concentrations, highlighting the importance of integrating comprehensive ventilation designs in modern residential buildings to ensure healthier indoor environments in Dubai.

A humidity-sensitive demand-controlled ventilation system is known for many years. It has been developed and commonly applied in regions with an oceanic climate. Some attempts were made to introduce this solution in Poland in a much severe continental climate. The article evaluates this system's performance and energy consumption applied in an 8-floor multi-unit residential building, virtual reference building described by the National Energy Conservation Agency NAPE, Poland. The simulations using the computer program CONTAM were performed for the whole hating season for Warsaw's climate. Besides passive stack ventilation that worked as a reference, two versions of humidity-sensitive demand-controlled ventilation were checked. The difference between them lies in applying the additional roof fans that convert the system to hybrid. The study confirmed that the application of demand-controlled ventilation in multi-unit residential buildings in a continental climate with warm summer (Dfb) leads to significant energy savings. However, the efforts to ensure acceptable indoor air quality require hybrid ventilation, which reduces the energy benefits. It is especially visible when primary energy use is analyzed.

Asthma is a significant public health concern. This study identified the provinces with the highest morbidity and mortality rates due to asthma among the working-age population (15-69 years) in the Republic of Ecuador. The secondary objective was to explain the possible differences attribut-able to occupational exposure. This nationwide ecological and exploratory study was conducted in 24 provinces between 2016 and 2019. Government databases were used as sources of infor-mation. Standardized rates were calculated for codes the J45 and J46. The hospitalization mor-bidity rate for asthma decreased from 6.51 to 5.76 cases per 100,000 working-age population, and the mortality rate has consistently been low and stable from 0.14 to 0.15 deaths per 100,000 working-age population. Geographic differences between the provinces were evident. The risk of hospitalization and death due to asthma was higher in the Pacific coast (five provinces) and the Andean region (two provinces). The high rates observed in provinces with greater agricultural and industrial development could be the main determinants of national heterogeneity and could act as occupational risk factors. The contribution of occupational hazards in each province should be examined in depth through ad hoc studies. These findings provide valuable information for creating public policies aimed at promoting and safeguarding the respiratory health of the popu-lation, particularly that of workers.

This paper evaluates an architectural design using an Energy Consumption consideration of Natural Ventilation in a hot dry climate (Khartoum State), at dwellings design applied. Method was used analysis of Autodesk IEVS software natural ventilation and energy consumption simulation. It resulted that to cooling, by natural ventilation in dwelling design used to get indoor temperature at the comfortable level during the summer. The Best-Case Situation of natural ventilation with consider of energy saving Based on the CFD simulation analysis, the performance of internal air velocity is approximately 0.7m/s. The wind velocity starts to slow down towards the rear of the apartment spaces. Approximately 95% of the internal areas have average air velocity between 0.43 m/s to 0.9 m/s. Internal Air flow pattern single floor house plan at Khartoum (Alazhari City); showing the internal air velocity of 0.7m/s near the window opening positions with the wind directions in the details and pressure of the air as worst-case situation, with velocity and temperature of the air with average 22o as a best-case situation. during a year. Architectural design process in the urban area of Alazhari City for dwelling towards to saving energy was applied and determined into an urban planning neighbourhood at Khartoum.

Over the last two months, as oncology specialists, we have frequently been contacted for estimating prognosis for cancer patients affected by COVID-19 infection. Until now, there have been no clear markers to guide decision making regarding the appropriateness of invasive ventilation in cancer patients affected by COVID-19 infection. Therefore, we developed a practical tool encompassing a prognostic score. We aimed at identifying a subgroup of patients likely to have a better outcome and therefore may be potential candidates for invasive ventilation, "The Milano Policlinico ONCOVID-ICU score". The score is composed by three groups of variables: patient’s characteristics such as sex, age, BMI and comorbidities; oncological variables (treatment intent, life expectancy, on or off-treatment status) and clinical parameters in association with laboratory values (SOFA score and D-dimer). The SOFA score includes six different clinical parameters and during the first few days of ICU admissions has an important prognostic role. The oncological history should never represent, per se, a contraindication to intensive care and must be considered together with other variables, such as laboratory values, clinical parameters and patient characteristics, in order to make the hardest but best possible choice. The Milano Policlinico ONCOVID-ICU score, to our knowledge, is the first prognostic score proposed in this setting of patients and may be a useful tool to assess the prognosis of cancer patients being in this critical condition.

The G-NUMEN array is the future gamma spectrometer of the NUMEN experiment (Nuclear Matrix Element for the Neutrinoless double beta decay), to be installed around the object point of the MAGNEX magnetic spectrometer at the INFN-LNS laboratory.. This project aims at exploring Double Charge Exchange (DCE) reactions in order to obtain crucial information about the neutrinoless double beta decay (0νββ). The primary objective of the G-NUMEN array is to detect the gamma rays emitted from the de-excitation of the excited states populated via DCE reactions with good energy resolution and detection efficiency, amidst a background composed of transitions from competingreaction channels with far higher cross-sections. To achieve this, the G-NUMEN signalswill be processed in coincidence with those generated by the detection of the reaction ejectiles in the MAGNEX Focal Plane Detector(FPD). Under the expected experimental conditions, G-NUMEN detectors will operate at high counting rates, of the order of hundreds of kHz per detector, while maintaining excellent energy and timing resolutions. The complete array will consist of over 100 LaBr3(Ce) scintillators. Initial tests have been conducted on the first detectors of the array, allowing for the determination of their performance at high rates.

During mechanical ventilation, a disparity between flow, pressure or volume demands of the patient and the assistance delivered by the mechanical ventilator often occurs. Asynchrony effect and ventilator performance are frequently studied from ICU datasets or using commercially available lung simulators and test lungs. This paper introduces an alternative approach of simulating and evaluating patient-ventilator interactions with high fidelity using the electro-mechanical lung simulator xPULM™ under selected conditions. The xPULM™ approximates respiratory activities of a patient during alternating phases of spontaneous breathing and apnoea intervals while connected to a mechanical ventilator. Focusing on different triggering events, volume assist-controlled (V/A-C) and pressure support ventilation (PSV) modes were chosen to test patient-ventilator interactions. In V/A-C mode a double-triggering was detected every third breathing cycle leading to an asynchrony index of 16.67%, being classified as severe. This asynchrony causes a major increase of Peak Inspiratory Pressure PIP = 12.80 ± 1.39 cmH2O and Peak Expiratory Flow PEF = -18.33 ± 1.13 L/min when compared to synchronous phases of the breathing simulation. Additionally, events of premature cycling were observed during PSV mode. In this mode, the peak delivered volume during simulated spontaneous breathing phases almost doubles compared to apnoea phases. The presented approach demonstrates the possibility of simulating and evaluating disparities in fundamental ventilation characteristics caused by double-triggering and premature cycling under V/A-C and PSV ventilation modes. Various dynamic clinical situations can be approximated and could help to identify undesired patient-ventilation interactions in the future. Rapidly manufactured ventilator systems could also be tested using this approach.

The SARS-Cov-2 virus, which causes COVID 19, uses the cell surface protein ACE2 as receptor for entry into cells. Critically ill COVID-19 patients often require prolonged mechanical ventilation which can cause mechanical stress to lung tissue. In vitro studies have shown that expression of ACE2 in alveolar cells is increased following mechanical stretch and inflammation. Therefore, we analyzed transcriptome datasets of 480 (non-COVID-19) lung tissues in the GTex tissue gene expression database. We found that mechanical ventilation of the tissue donors increased the expression of ACE2 by more than two-fold (p<10^-6). Analyses of transcriptomes of mechanically ventilated mice in the GEO database indicate that this alveolar cell response to stretch and inflammation is mediated by the chemokine midkine. Using a novel big knowledge network approach (SPOKE) we also found in transcriptomes of pharmacological perturbations (LINCS) that corticosteroids down-regulate midkine in pulmonal cells, and confirmed this in GEO transcriptomes of animal studies. Thus, mechanical ventilation of patients with COVID-19 pneumonia may eo ipso facilitate viral propagation in the lung, further accelerating the pulmonal pathology that has necessitated mechanical ventilation in the first place. This vicious cycle presents a rationale for the temporary treatment with corticosteroids to modulate the midkine-ACE2 axis in ventilated COVID19 patients and for gentler ventilation protocols.

The length of time it takes to experimentally make one-sided choppers, as found in the fossil record, bears a linear relationship to the knapping process of fabricating them. In addition, this temporal frame appears to be related to human heart rates measured as beats per minute, which act as a physiological metronome. We achieved these observations assuming that any paleolithic one-sided chopper has the information needed to estimate quantitatively the number of strikes on it. The experimental data allow us to establish the total timing needed for the standard fabricating of any one-sided chopper. We discuss issues derived from these experimental results, showing the evolution of human neurological abilities from 2.4 million years ago to the Modern period through the duration of time needed for making one chopper to that needed to play a 19th-century music score on a piano. Given that the neuronal and physiological distance between both actions differs by a factor of 6, we propose the concept of “technome” to measure human evolution by using methodological homogeneous metrics applied to these two human technologic objects, the chopper and the piano.

This work explored and contrasted the effect of microstructure on the tensile properties of AlSi10Mg alloys generated by transient directional solidification depending on variations in cooling rate and Magnesium (Mg) content (i.e., 0.45 and 1wt.% Mg), with a focus on understanding the dendritic growth and phases constitution. Optical and Scanning electron (SEM) microscopies, CALPHAD and thermal analysis were used to describe the microstructure, forming phases and resulting tensile properties. The findings showed that the experimental evolution of the primary dendritic spacing is very similar when both directionally solidified (DS) Al-10wt.% Si-0.45wt.% Mg and Al-10wt.% Si-1wt.% Mg alloys samples are compared. The secondary dendritic spacing was lower for the alloy with more Mg, especially considering the range of high growth velocities. Moreover, a greater fraction of (Al+Si+Mg2Si) ternary eutectic islands surrounding the -Al dendritic matrix was noted for the alloy with 1wt.% Mg. As a result of primary dendritic spacings greater than 180 m related to lower cooling rates, slightly higher tensile properties were attained for the Al-10wt.% Si-0.45wt.% Mg alloy. In contrast, combining dendritic refining (< 150 m) and larger Mg2Si fraction, fast solidified DS Al-10wt.% Si-1wt.% Mg samples exhibited higher tensile strength and elongation. The control of cooling rate and fineness of the dendritic array provided a new insight related to the addition of Mg in slightly higher levels than conventional ones, capable of achieving a better balance of tensile properties in AlSi10Mg alloys.

The coronavirus disease pandemic 2019 (COVID-19) has emerged in Wuhan province, China in December 2019 and has spread over all countries. The current study was carried out to predict active, death and cured rate of COVID 19 in Algeria for a future period of 35 days using FB prophet model. Results shoed that the active rate and the death rate decrease for the next days while the cured rate increase. The active, cured and death rates are estimated at 19.7% 78.85% and 2.55% respectively. These results highlight the importance of FB prophet model in COVID-19 prediction which could help national authorities in adopting the best preventive measures.

While obesity is a serious chronic condition, its prevalence and documentation as a diagnosis has not been extensively studied in hospitalized patients. We conducted a retrospective chart review to investigate the prevalence and documentation of obesity as a diagnosis among patients admitted to our medical center. IRB approval was obtained for this retrospective study. Body mass index as per CDC, admission and discharge diagnosis of obesity and common comorbidities including hypertension, diabetes, hyperlipidemia and others, were recorded. Length of hospital stay was calculated. We also investigated whether counselling for weight loss was provided to obese patients. A total of 540 consecutive patients with mean age of 66 ± 6 years, were investigated, of which 182(34%) had normal weight, 188(35%) patients were overweight and 170(31%) patients were obese. Obese group included 55% female and 45% male. 100 (59%) had class I obesity, 43(25%) had class II obesity and 27(16%) class III obesity. Of the obese patients 40/170(23.5%) patients had obesity documented on the admission problem list and only 21(12%) had obesity documented as a discharge diagnosis. Only 3(2%) patients received appropriate counseling and referral for obesity management during the hospitalization. Comorbidities included hypertension (68%), diabetes (35%), hyperlipidemia (36%), coronary artery disease (18%), chronic kidney disease (17%), congestive heart failure (18%) and COPD (24%). The average length of stay in normal weight, overweight and obese patients was similar (4.5 ± 0.5 days). An overwhelming percentage never had weight status documented despite significant prevalence of obesity. Hospitalization offers health care providers a window of opportunity to identify obesity, communicate risks and initiate weight management interventions.

This study presents an analysis of subsidence rates and their effects on Mexico City. Mexico City is well known for its subsidence as a result of excess water withdrawal for many years. This study focuses on this problem utilizing the integration of Interferometric Synthetic Aperture Radar (InSAR), Continuous Global Positioning Systems (CGPS), and optical remote sensing data. Fifty-two ENVISAT-ASAR, nine GPS stations, and one Landsat ETM+ image from Mexico City area have been analyzed to prepare a better understanding of the subsidence rates and its effects on Mexico City’s commune. This study has utilized InSAR methods. It includes differential interferometry and Persistent Scatter Interferometry (PSI) to monitor the existing subsidence in the Mexico City area. The InSAR data covers the temporal baseline between 2002 until June 2010, and the GPS data include temporal baseline from 1998 until 2012. Maximum of 352 mm annually change in Line Of Sight (LOS) direction is in agreement with the previous geodetic studies. InSAR data have been compared with CGPS data at the same time interval. The finding of this study reveals a high amount of correlation (up to 0.98) between two independent geodetic methods. We also implemented the Support Vector Machine (SVM) analysis method based on Landsat ETM+ image to classify Mexico City’s populated density area. This method performed comparing the subsidence rates with populated area buildings. This integrated study shows that the fastest subsidence zone (i.e., areas greater than 100 mm/yr) in the over mentioned temporal baseline occurs in the high and sparsely populated areas

Hypertension stands as the foremost modifiable risk factor for cardiovascular disorders in South Asia. This research demonstrates the superiority of statistical models over traditional approaches in identifying clinical risks related to hypertension. Leveraging individual-level data from the Bangladesh Demographic and Health Survey (2017-18), a unified dataset was created. Adhering to JNC7 and ACC/AHA guidelines for hypertension classification, two prominent regression models were employed to estimate the prevalence of undiagnosed hypertension. A substantial 16% of hypertension cases in Bangladesh remain undetected. The study identifies undiagnosed hypertension as a heightened risk, particularly among the youth and residents of Sylhet and Rangpur divisions. Statistical models exhibit efficacy in discerning undiagnosed hypertension and associated factors in South Asia. Subsequent investigations should incorporate biological markers to enhance statistical models and ascertain their practicality.

Utility of vaccine campaigns to control coronavirus disease 2019 (COVID-19) is not merely dependent on vaccine efficacy and safety. Vaccine acceptance among the general public and the healthcare workers, appears to have a decisive role for successful control of the pandemic. The aim of this review was to provide an up-to-date assessment of COVID-19 vaccination acceptance rates worldwide. A systematic search of the peer-reviewed English survey literature indexed in PubMed was done on December 25, 2020. Results from 30 studies, met the inclusion criteria and formed the basis for final COVID-19 vaccine acceptance estimates. Results of an additional recent survey from Jordan and Kuwait was considered in this review as well. Survey studies on COVID-19 vaccine acceptance rates were found from 33 different countries. Among adults representing the general public, the highest COVID-19 vaccine acceptance rates were found in Ecuador (97.0%), Malaysia (94.3%), Indonesia (93.3%) and China (91.3%). On the other hand, the lowest COVID-19 vaccine acceptance rates were found in Kuwait (23.6%), Jordan (28.4%), Italy (53.7), Russia (54.9%), Poland (56.3%), US (56.9%), and France (58.9%). Only eight surveys among healthcare workers (doctors, nurses) were found, with vaccine acceptance rates ranging from 27.7% in the Democratic Republic of the Congo to 78.1% in Israel. In a majority of survey studies among the general public (62%), the acceptance of COVID-19 vaccination showed a level of ≥ 70%. Low rates of COVID-19 vaccine acceptance were reported in the Middle East, Russia, Africa and several European countries. This could represent a major problem in the global efforts that aim to control the current COVID-19 pandemic. More studies are recommended to address the scope of COVID-19 vaccine hesitancy. Such studies are particularly needed in the Middle East Africa, Eastern Europe, Central Asia, Middle and Latin America.

Background: Infantile haemangiomas (IH) may require treatment with propranolol. Sleep disturbances are the most fre-quently reported side effects. Monitoring drug adverse events necessitates repeated hospital visits, despite the SARS-CoV-2 pandemic. Objectives: To explore the effectiveness of a new electronic questionnaire in identifying sleep disturbances as adverse events to treatment and potential confounders. To evaluate the response rate to the questionnaire. To report the propor-tion of patients on propranolol with sleep disturbances. Methods: In an observational, prospective cohort study, caregivers provided clinical information at office visits and via an electronic questionnaire after an 8-week treatment course and at treatment interruption. Adverse drug reaction (ADR) reporting forms were evaluated for causality assessment. Results: The questionnaire response rate was 91%, and the completion rate was 100%. The prevalence of sleep disturb-ances as adverse reactions was 59%. Sleep disorders were more frequent during sleep regression phases and in subjects who fell asleep with physical contact with caregivers or bed-sharing with parents. Conclusion: The application of this questionnaire allows for identifying sleep-adverse events associated with propranolol in IH and potential confounders. Counselling on sleep hygiene is recommended before treatment onset

Tree pruning is a management tool in agroforestry systems for reducing shade, enhancing nutrient cycling or providing fodder. However, little information is available on the effect of pruning management on plant growth, non-structural carbohydrate (NSC) levels in the roots and N2 fixation of Sesbania sesban. A glasshouse experiment was conducted to assess the effect of pruning frequency on biomass production, NSC levels and N2 fixation of Sesbania sesban. Treatments included pruning at (i) 3 months only, (ii) 3 and 6 months, and (iii) 3, 6 and 9 months, with each pruning removing shoot biomass above 50% of the initial height. Increased pruning frequency decreased above- and belowground dry matter (DM), and root NSC levels. The decrease in aboveground DM correlated with reduced levels of starch, sugar and total non-structural carbohydrates. Pruning more frequently significantly decreased nodulation, the percentage N derived from the atmosphere and N2 fixed. It could be concluded that more frequent prunings decreases biomass and NSC levels which could reduce the regeneration capacity of trees since they rely on NSCs to regrow. The suppressive effects of increased pruning frequency on N2 fixation could decrease the desirable benefits of legume trees on soil N fertility improvement.

The powder bed fusion (PBF) metal additive manufacturing (AM) method uses an energy source like a laser to melt the metal powders. The laser can locally melt the metal powders and creates a solid structure as it moves. The complexity of the heat distribution in laser PBF metal AM is one of the main features that need to be accurately addressed and understood to design and manage an optimized printing process. In this research, the dependency of local thermal rates and gradients on print after solidification (in the heat-affected zone) was numerically simulated and studied to provide information for designing the print process. The simulation results were validated by independent experimental results. The simulation shows that the local thermal rates are higher at higher laser power and scan speed. Also, the local thermal gradients increase if the laser power increases. The effect of scan speed on the thermal gradients is opposite during heating versus cooling times. Increasing the scan speed increases the local thermal gradients in the cooling times and decreases the local thermal gradients during the heating. In addition, these simulation results could be used in artificial intelligence (AI) and machine learning for developing digital additive manufacturing.

This study investigated the trends of registered Death and Birth in Nigeria using Generalized Linear Models. Annual data on Death and Birth was collected from National Population Commission for the period of 2004 to 2017. The Natural increase calculated revealed a positive trend in the natural increase in Nigeria from 2004 to 2017. Evidence from summary statistics revealed some level of over dispersion (variance > mean). This study explored Poisson Regression Models and Negative Binomial Regression Models using two links (identity and log). The results revealed a positive increase in registration of birth and death rates in Nigeria and among the competing the models, Negative Binomial regression model with identity link emerged as the best model for modeling birth and death rates registration in Nigeria. Data on numbers of deaths and causes of death are essential if countries are to determine priorities, formulate and monitor policies for public health care as well as other government policies that may be based on such data

The work proposes a backtesting analysis in comparison between the Lee-Carter and the Cairns-Blake-Dowd mortality models, employing Italian data. The mortality data come from the Italian National Statistics Institute (ISTAT) database and span the period 1975-2014, over which we computed back-projections evaluating the performances of the models in comparisons with real data. We propose three different backtest approaches, evaluating the goodness of short-run forecast versus medium-length ones. We find that both models were not able to capture the improving shock on the mortality observed for the male population on the analyzed period. Moreover, the results suggest that CBD forecast are reliable prevalently for ages above 75, and that LC forecast are basically more accurate for this data.

The exposure of employees to specific risks is usually due to increasing levels of work-related stress, which negatively affects their skills and effectiveness in their job duties, lead-ing to the onset of physical/mental illnesses, mistakes, or even accidents. The aim of this study is to investigate the psychosocial risks experienced by nurses in tertiary hospitals in Greece and their association with their attitudes towards safety and the occurrence of medication errors. The research was conducted in four tertiary hospitals in Greece, with the participation of 514 nurses of all educational levels. Questionnaires were used to collect data on work-related stress, professional burnout, and medication errors. The results highlighted that psychosocial risks, such as high work pressure and lack of support, are directly linked to professional burnout and an increased likelihood of medication errors. The necessity of social support, job autonomy, and work-life balance are underscored as critical factors for reducing stress and improving the quality of care. Specific strategies are proposed to enhance the mental health of nurses and improve working conditions.

Hepatitis B and C are major health issues in developing countries such as Pakistan and Afghan-istan. The aim of this study was to determine the prevalence and effectiveness of a screening program for hepatitis B and C in a region with no existing programs, and to estimate their prev-alence in the general population in Khyber Pakhtunkhwa Province, Pakistan, as well as in Afghan refugees or migrants. A prospective cohort study was done in the general population of Peshawar and its adjacent districts, as well as migrants from neighboring provinces of Afghani-stan, who presented to our tertiary-care health facility. A Microsoft Excel registry was created for data collection, which were analyzed using IBM SPSS via descriptive analysis, normal distribution curve histograms, and chi-squared tests. A total of 9563 individuals were screened for hepatitis (5894 males and 3669 females), including Afghan migrants in Peshawar and surrounding districts. 876 individuals tested positive for hepatitis, with 538 positive for hepatitis B (383 males and 155 females) and 330 positive for hepatitis C (198 males and 134 females). Eight individuals had a hepatitis B and C co-infection. Among the study population, the prevalence rates were 2.2% for hepatitis B and 2.3% for hepatitis C, of which the Afghan migrants accounted for 2.7% and 0.5%, respectively. According to the gender-based distribution, hepatitis B was more prevalent in males, whereas there was no significant gender-based difference for hepatitis C. Our results highlight the need for a comprehensive approach to control hepatitis B and C in Pakistan and Afghanistan. Increased awareness, improved healthcare, and preventive measures such as screening and elimination programs to prevent severe liver diseases and eradicate hepatitis are necessary.

This study aligns with the 2030 United Nations Sustainable Development Goals- 3 which aim to “ensure healthy lives and promote well-being for all at all ages”. It contributes to the nascent literature stream on energy-health dynamics by introducing a holistic theoretical model to empirically examine the mediation effect of carbon emissions on the relationship between nonrenewable energy and infant mortality rates. Using an unbalanced panel data on 42 Asia and the Pacific countries from 2005 to 2015 and deploying the structural equation modeling approach, the empirical results are surmised as follows: (i) in regard to the full sample of countries, nonrenewable energy indirectly increases infant mortality rates through increasing carbon emissions. In other words, carbon emissions play a partial mediation role between nonrenewable energy and infant mortality rates; and (ii) for the different income groups, carbon emissions show varying mediation effects. For example, the mediation effects of carbon emissions in lower-middle and upper-middle income countries are found to be similar to those of the full sample of countries. Therefore, based on these findings, we conclude that nonrenewable energy is an essential determinant of infant mortality rates. Policy recommendations are put forward.

Objective: This study aims to identify the impact of nutritional factors on mechanical ventilation duration for critical patients. Patients and Methods: The current study was a single-center, prospective observational design which enrolled one-hundred critically ill patients who were admitted to an intensive care unit (ICU). It demonstrates purposive sampling and also performs the descriptive nutritional factors influencing the mechanical ventilation duration. Daily calories target requirement scale (DCRS), subjective global assessment form (SGA), dyspnea assessment form, and APACHE II have been used as methods in the study along with time to initial enteral nutrition (EN) after 24-hour admission and daily calories target requirement over 7 days to assess patients. Data is analyzed using the multiple regressions. Results: As a result, nutritional status monitoring, time to initial EN, calories and target requirements are statistically positive significance associated with the mechanical ventilation duration respectively (R = 0.54, R = 0.30, R= 0.40, p < 0.05). However, age, illness severity, and dyspnea scales are not associated with the mechanical ventilation duration (p> 0.05). Therefore, the nutritional status, malnutrition scores and calorie target requirements can be used to significantly predict the mechanical ventilation duration. The predictive power is 58 and 28.0% of variance. The most proper influencer to predict the mechanical ventilation duration is nutritional status or malnutrition scores. Conclusion: The research findings show that the nutritional status, time to initial EN, and calorie target requirement within 7 days of admission are associated with the mechanical ventilation duration in the critical patients. Therefore, it can be used to develop guidelines reducing the mechanical ventilation duration and to promote the ventilator halting for critical patients.

This study concerns calculation and comparison of Fe, Co, Ni and Cu deposition rates in tungsten codeposition process based on electrodeposition of numerous tungsten alloys. 8 different tungsten alloys containing from 2 to 5 metals were electrodeposited in constant conditions in order to compare exact reduction rates. Calculated rates enabled control of the alloy composition precise enough to obtain a high-entropy WFeCoNiCu alloy with well-balanced composition. Introduction of copper to form the quinternary alloy was found to catalyze the whole process, increasing deposition rates of all components of the high-entropy alloy.

Helicobacter pylori (H. pylori) is a common bacterial infection linked to gastric malignancies. While H. pylori infection and gastric cancer rates are decreasing, antibiotic resistance varies greatly by community. Little is known about resistance rates among rural Indigenous populations in the United States. From 2018 to 2021, 396 endoscopy patients were recruited from a Northern Arizona clinic, where community H. pylori prevalence is near 60%. Gastric biopsy samples positive for H. pylori (n=67) were sequenced for clarithromycin and metronidazole-associated mutations, 23S ribosomal RNA (23S), and oxygen-insensitive NADPH nitroreductase (rdxA) regions. Medical record data were extracted for endoscopic findings and prior H. pylori history. Data analysis was restricted to individuals with no history of H. pylori infection. Of 49 individuals, representing 64 samples that amplified in the 23S region, a clarithromycin-associated mutation was present in 38.8%, with T2182C the most common mutation, 90%. While prevalence of metronidazole resistance-associated mutations was higher, 93.9%, mutations were more variable, with D95N the most common, followed by L62V. No statistically significant sex differences were observed for either antibiotic. Given the risk of treatment failure with antibiotic resistance, there is a need to consider the resistance profile during treatment selection. The resistance rates in this population of American Indian patients undergoing endoscopy are similar to other high-risk populations. This is concerning given the high H. pylori prevalence and low rates of resistance testing in clinical settings. The mutations reported are associated with antibiotic resistance, but clinical resistance must be confirmed.

$\beta$-decay is one of the key factors to understand the $r$-process and evolution of massive stars. The Gamow-Teller (GT) transitions drive the $\beta$-decay process. We employ the proton-neutron quasiparticle random phase approximation (pn-QRPA) model to calculate terrestrial and stellar $\beta$-decay rates for 50 top-ranked nuclei possessing astrophysical significance according to a recent survey \cite{Nab21}. The model parameters of the pn-QRPA model effect the predicated results of $\beta$-decay. The current study investigates the effect of nucleon-nucleon pairing gaps on charge-changing transitions and the associated $\beta$ decay rates. Three different values of pairing gaps, namely TF, 3TF and 5TF, were used in our investigation. It was concluded that both GT strength distributions and half-lives are sensitive to pairing gap values. The 3TF pairing gap scheme, in our chosen nuclear model, resulted in best prediction with around 80$\%$ of the calculated half-lives within a factor 10 of the measured ones. The 3TF pairing scheme also led to calculation of biggest $\beta$-decay rates in stellar matter.

In this paper, we constructed and analyzed a modified SIR-type model for the epidemic problem which considering waning-immunity class in the population, with the nonlinear incidence and recovery rates. Depending on the basic reproduction ratio, we investigated conditions for both non-endemic and co-existing cases. The RouthHurwitz criteria is used to verify the local stability of equilibria, whereas for the global stability, the suitable Lyapunov function is selected to analyze the behavioral stability for each equilibria. Moreover, we studied the optimal control problem for this case. Numerically, we give some simulations to support our analitycal findings.

Semantic rules link purely theoretical terms like “price” and “electron” to things we can measure. Without them, theories cannot be tested empirically. When inappropriate, they produce false rejections. Economists routinely ignore semantic rules. Empirical journal articles essentially never mention them. More to the point, the conventional tests that reject the Law of One Price and Purchasing Power Parity never consider them. As a result, those rejections are unwarranted because such tests use inappropriate semantic rules. Both theories should be restored to not rejected and then retested using the more appropriate semantic rules described here. By using appropriate semantic rules, this paper is able to combine Covered Interest Parity and Purchasing Power Parity into a single theory that links auction markets for financial assets and commodities to auction markets for exchange rates. Using appropriate semantic rules for both theories also explains several puzzles in open economy macroeconomics and opens up broad new vistas for research.

A recent study by the Wall Street Journal reveals that the hydrofractured horizontal wells in shales have been producing less than forecasted by the industry with the empirical hyperbolic decline curve analysis (DCA). As an alternative to DCA, we introduce a simple, fast and accurate method of estimating ultimate recovery (EUR) in oil shales. We adopt a physics-based scaling approach to analyze oil rates and ultimate recovery from 14,888 active horizontal oil wells in the Bakken shale. To predict EUR, we collapse production records from individual horizontal shale oil wells onto two segments of a master curve: (1) We find that cumulative oil production from 4,845 wells is still growing linearly with the square root of time; and (2) 6,401 wells are already in exponential decline after approximately seven years on production. In addition, 2,363 wells have discontinuous production records, because of refracturing or changes in downhole flowing pressure, and are matched with a linear combination of scaling curves superposed in time. The remaining 1,279 new wells with less than 12 months on production have too few production records to allow for robust matches. These wells are scaled with the slopes of other comparable wells in the square-root-of-time flow regime. In the end, we predict that total ultimate recovery from all existing horizontal wells in Bakken will be some 4.5 billion barrels of oil. We also find that wells completed in the Middle Bakken formation, in general, produce more oil than those completed in the Upper Three Forks formation. The newly completed longer wells with larger hydrofractures have higher initial production rates, but they decline faster and have EURs similar to the cheaper old wells. There is little correlation among EUR, lateral length, and the number and size of hydrofractures. Therefore, technology may not help much in boosting production of new wells completed in the poor immature areas along the edges of the Williston Basin. Operators and policy-makers may use our findings to optimize the possible futures of the Bakken shale and other plays. More importantly, petroleum industry may adopt our physics-based method as an alternative to the overly-optimistic hyperbolic DCA that yields an "illusory picture" of shale oil resources.

Loess was deposited in the Negev during the Pleistocene, but such sediments seem to be missing for the Holocene. This could be due to erosion unless structures such as ruins offered protection. We studied soils developed on archaeological hilltop ruins in the Negev and the Petra region and compared them with local soils, paleosols, geological outcrops, and current dust. The ruin soils in both regions were found to consist of similarly complex mixtures of local and remote sediment sources. They differ from sediments deposited during current dust storms. This seems due to fixation processes: average accretion rates are estimated to ~0.14 mm/a, suggesting that only ~3% of the current dust that can be trapped with dry marble dust collectors is stored in the soils. Vegetation, biocrusts, and/or clast pavements associated with vesicular layers seem to act as sediment-fixing agents. As well, climate might play a role: rain, and in particular one snowstorm in the Petra region brought a high amount of sediment that was more similar to the ruin soils. Wet deposition and snow might catalyze dust deposition and enhance fixation by fostering vegetation and crust formation. Frequent snow during the Pleistocene might be one explanation of enhanced loess deposition.

Balanced nitrogen (N) and phosphorus (P) rates coupling with rational fertilization methodology could promote crop N accumulation, N use efficiency and yield production, particularly in semi-arid and arid regions. To test these characteristics, a two-year (2018 and 2019) pot experiment was therefore performed by growing summer maize in a rain-proof glass greenhouse, under 9 combined N (112, 150 and 187 kg ha-1, urea) and P (45, 60, 75 kg ha-1, calcium superphosphate) rates and three contrasting fertilizer placements. The fertilizers were placed by broadcast on soil surface (Broadcast), side band on 4 cm strip soil surface within 7 cm from sowing line (Side band) and deep band on 4 cm strip below 7 cm soil depth within 7 cm from sowing line (Deep band). Results from three maize growth stages (eight-leaf, 45 days after sowing, DAS; tasseling, 60 DAS; and harvest, 115 DAS) showed that leaf, stem, root N accumulation and total soil N were significantly increased under Deep band than under both Side band and Broadcast at N150P60, N187P60, N150P75 and N187P75, but not at N112P45, N150P45, N187P45, N112P60 and N112P75. Significantly greater leaf, stem, and root N accumulations were also displayed at N150 and N187 than at N112 for the same P60 or P75 under Deep band at 60 DAS and 115 DAS, while were for leaf and stem N accumulations at P75 and P60 than at P45 for the same N150 under Deep band at 45 DAS, 60 DAS and 115 DAS. Significantly greater agronomy N use efficiency, partial factor productivity and N use efficiency exhibited under Deep band than under Side band and Broadcast at N150P75 and N187P75, but at N150P60 and N187P60 for NUE only. In addition, leaf, stem, seed, root N concentrations positively correlated with their own N accumulations or soil N concentration at tasseling and harvest stages. Our results demonstrate that a synchronized N150P60, N187P60, N150P75 or N187P75 fertilization rate with Deep band placement can improve soil N availability and root N uptake, and hereby greater aboveground N accumulation, N use efficiency and yield production of maize particularly practical for small-holder farmers globally.