In this study, in order to determine the effect of matrices shape on percolation threshold values, computer simulations were performed using the Monte Carlo method for a 200x200 square-shaped matrix and rectangular matrices containing the same number of nodes as the square matrix. Based on the simulations, the average values of percolation thresholds and standard deviations for current flow along and across the matrices were determined. It was determined that for a square-shaped matrix, the average values of percolation thresholds in both directions of current flow were the same. Extending the rectangular matrix while reducing its height causes the average value of the percolation threshold in the direction of current flow along the matrix to increase from 0.592740 to 0.759847, while in the transverse direction it decreases from 0.592664 to 0.403614. The values of the classical asymmetry coefficients of the probability distributions of percolation thresholds for both directions of current flow were determined. Histograms of the probability distributions of percolation threshold values for square-shaped matrix and rectangular matrices were made and compared with normal distributions. It was found that the occurrence of two percolation thresholds in rectangular layers should be considered when analyzing electrical conductivity measurements of nanocomposite thin films.

Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

Resonance inductive coupling is widely used for wireless power transfer (WPT) in medical applications. In this paper, we analyze the LCL-compensated WPT structure and propose a novel constant voltage transmission system based on gain estimation, without any extra feedback from the receiver. The system is capable for implant neural stimulation where the load impedance and the coupling coefficient are both variable. Compared to existing methods for constant voltage transmission, our approach offers advantages in compact size and the compatibility with the industrial, scientific and medical (ISM) band. We validate the load-independent resonant characteristic and the feasibility of constant voltage transmission using an experimental prototype working at 6.78MHz. Finally, we discuss the structure of the implant stimulator and methods of applying the proposed WPT system.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

Dielectric Elastomer Actuators (DEAs) are emerging as promising candidates for various applica-tions in robotics and optical devices due to their lightweight, miniaturization potential, high en-ergy density, simple structure, and low power consumption. However, their effective actuation always demands sophisticated high-voltage driving circuits that are compact and responsive. DEAs need to be capable of generating intricate high-voltage waveforms or simultaneously con-trolling multiple channels with distinct high-voltage levels. This paper proposes a high-voltage power supply for DEAs, featuring a four-channel high-voltage driving circuit. The circuit is ca-pable of independently generating high-voltage signals ranging from 100 V to 6000 V and can be programmed to produce arbitrary waveforms with adjustable frequencies. The independent op-eration of channels without crosstalk showcases the system's integration and potential for cross-disciplinary applications.

The integration of magnetic observatories of many countries into the Intermagnet network has provided researchers with new opportunities to investigate many geophysical processes. The joint processing of measurement evidence from magnetic observatories located in various geolocations makes it possible to better understand the dynamics of the interaction of solar plasma fluxes with the Earth's magnetosphere. For the correct interpretation of the dynamics of physical processes, the accuracy of the time reference of measurement results is of great importance. The measurement results of local observatories were transformed to a unified ecliptic coordinate system oriented towards the Sun in order to extract small variations in the magnetic field occurring before the magnetic storm commencement. Before transforming the coordinates, a constant component equal to the average daily value of the magnetic field components was removed from the results of minute-by-minute measurements. Owing to the averaging evidence from 84 magnetic observatories of the Intermagnet network, variations in the magnetic field of cosmic origin, preceding the magnetic storm commencement were detected. The correlation analysis of these variations recorded by different observatories revealed the presence of time shifts between the data series of different observatories. Only 62% of the observatories had a relative data shift within the range of ± 1 minute. Before the joint data processing in order to efficient use of data recorded with a time shift a method for correcting time shifts has proposed.

Herein, we present the design technique of a resonant rectifier for piezoelectric (PE) energy harvesting. We propose two diode equivalents to reduce the voltage drop in the rectifier operation, a minuscule-drop-diode equivalent (MDDE) and a low-drop-diode equivalent (LDDE). The diode equivalents are embedded in resonant rectifier integrated circuits (ICs), which use symmetric bias-flip to reduce the power wasted for charging and discharging the internal capacitance of a PE transducer. The self-startup function is supported by synchronously generating control pulses for the bias-flip from the PE transducer. Two resonant rectifier ICs, using both MDDE and LDDE, are fabricated in a 0.18 μm CMOS process and their performances are characterized under external and self-power conditions. Under the external-power condition, the rectifier using LDDE delivers an output power POUT of 564 μW and a rectifier output voltage VRECT of 3.36 V with a power conversion efficiency (PCE) of 90.1%. Under self-power conditions, the rectifier using MDDE delivers a POUT of 288 μW and a VRECT of 2.4 V with a corresponding PCE of 74.6%. The result shows that the power extraction capability of the proposed rectifier is 5.9 and 3.0 times higher than that of a conventional full-bridge rectifier.

A power factor correction (PFC) rectifier is compulsory for any electronic circuitry connected to the electrical grid. The majority of PFCs that are utilized are based on a step-up converter that supplies high DC voltage at its output terminal. Electric vehicle battery voltage varies from a few hundred to almost a thousand volts. Thus, an additional conversion step is obligatory when designing an all-brand universal charger. This paper presents a new type of front-end versatile step up / down three voltage level PFC. The rectifier can operate in continuous conduction mode or discontinuous conduction mode. First, the rectifier’s principle of operation is described, and then an innovative rectifier is analyzed for continuous and discontinuous conduction modes. Finally, the proposed theory is experimentally validated in a multiplier-less dual loop mode at discontinuous conduction modes. It was shown that although there is no multiplier use in the control circuitry, the power factor is near unity. It was revealed that the rectifier could swing the output voltage from 50 V to 900 V while the input voltage was 230 Vrms. The innovative topology suits any standard PFC rectifier, three-level voltage supplement, and dual-stage low-voltage power supply.

Induction motors are the most numerous and significant dynamic loads in power systems. In transient voltage stability analysis, dynamic equivalent models are commonly used to simplify the representation of a group of induction motors. This paper presents an method for the grouping and aggregation of induction motors at a common bus. Firstly, grouping rules were provided for clustering induction motors into several subgroups based on the mechanical principles of rotor force and motion, and Aggregation Rules were provided for aggregating a motor subgroup into a single-unit model based on the relationship between voltage drop and power transmission in distribution networks. Secondly, guided by the grouping rules, high-speed remaining electromagnetic torque and low-speed remaining electromagnetic torque were defined as new clustering indicators, and an adaptive K-means clustering method using silhouette coefficient verification was provided to obtain the optimal motor subgroups. Thirdly, guided by the Aggregation Rules, a dynamic equivalent method was further provided to obtain the equivalent single-unit model from a motor subgroup. Lastly, a transient voltage stability simulation in a typical distribution network was presented to illustrate that the proposed clustering and equivalent methods are more reasonable, accurate, and effective than traditional methods, as the obtained model has better dynamic characteristics and can more accurately reproduce the process of voltage collapse.

Natural polluted insulator surfaces are always coated with various kinds of soluble constituents, and those constituents affect flashover performance differentially. Currently this fact is not considered either in laboratory experiments or field pollution degree measurements, causing the existing insulation selection method to be deficient. In this paper a systematical research on insulator flashover voltage gradient correction involving types of soluble pollution constituents was presented. Taking typical type glass insulator as the sample, its flashover tests polluted by typical soluble chemicals NaCl, NaNO₃, KNO₃, NH₄NO₃, MgSO₄, Ca(NO₃)₂ and CaSO₄ were carried out. Then the flashover gradient correction was made combining the flashover performance of each soluble constituent, the ESDD contribution of the seven constituents, as well as the saturation performance of CaSO₄. The correction was well verified with the flashover test results of insulator polluted by three types of soluble mixture. Research results indicate that the flashover gradient correction method proposed by this paper performs well in reducing the calculating error. It is recommended to carry out component measurements and flashover gradient correction to better select outdoor insulation configuration.

Current paper is aiming to show the obtained results in manufacturing and characterization of graphite-based and metal composite materials suitable to be used in high voltage applications of automotive and/or aviation field. Thus, 4 types of materials have been processed and tested in order to assess their suitability to be used as current collector material for electric engines. The novelty of this work is the presentation of the new innovative technological process for obtaining the carbon/metal composite material used in the manufacture of sliding contacts for current collector heads, as well as the characteristics obtained for this material. All 4 obtained materials have been characterized from structural, mechanical and functional point of view and the most suitable of them has been chosen to be further developed by the end beneficiary.

Among the major systems of high-speed rail, the arch network relationship, wheel-rail relationship and fluid-structure coupling relationship are important links affecting the performance of high-speed rail, and also the main control factors affecting the speed limit of high-speed rail. From this perspective, the contact state and interactive relationship between pantograph and catenary are the key factors affecting the forward performance of high-speed rail. As a key component in the pantograph system, the actuator is responsible for adjusting the contact force and position between the pantograph and the contact line. The performance characteristics of the actuator, such as response speed, accuracy, stability and durability, directly affect the control performance of the whole pantograph system. In this paper, the research status of the active control technology of high-speed railway pantograph is reviewed, and the future development direction is pointed out, which provides a new idea for the development of pantograph technology.

With the development of higher voltage power grid, the high and low voltage parallel loops are emerging, which lead to energy losses, even threaten the security and stability of power system. The multi-infeed HVDC configurations widely appearing in AC/DC interconnected power system make this situation even worse. Aimed at energy saving and system security, a decision optimization method for power grid operating condition with high and low voltage parallel loops is proposed in this paper. Firstly, considering hub substation distribution and power grid structure, parallel loop opening schemes are generated with GN algorithm. Then, candidate opening schemes are preliminarily selected from all these generated schemes based on a filtering index. Finally, with the influence on power system security, stability and operation economy in consideration, an evaluation model for candidate opening schemes is founded based on analytic hierarchy process (AHP). And a fuzzy evaluation algorithm is used to find the optimal scheme. Simulation results of New England 39-bus system and an actual power system validate the effectiveness and superiority of this proposed method.

As the penetration of renewable energies increases, their acceptance of the power grid system is becoming an important issue. In the case of South Korea, a 22.9kV transformer is frequently utilized to reduce the power loss of the generated renewable energy transmission, so the power quality at the point of common connection (PCC) is inevitably influenced by the nonlinearity of the transformer and the uncertainty of the inductance and resistance of the transmission line. In this paper, we present a point of common connection voltage-modulated direct power control (PCCVM-DPC) system that enhances power quality at the PCC. First, we present the mathematical dynamics of active and reactive power at the PCC side, which contains the step-up transformer’s nonlinearity, the grid voltage harmonics, and the parameter uncertainties. By analyzing the disturbance terms of the PCCVM-DPC system, we present the disturbance observer (DOB) for the PCCVM-DPC system. To assess the efficacy of our approach, we perform comparative studies of the PCCVM-DPC without DOB and PCCVM-DPC with DOB by constructing the simulation environment based on the commercial step-up transformer and ESS inverter datasheet. We have validated that the active and reactive power control performance of the PCCVM-DPC with DOB outperforms the PCCVM-DPC without DOB from the observation that the current total harmonic distortion reduced by more than 40% compared to the PCCVM-DPC without the DOB.

With the widespread use of new equipment such as distributed photovoltaics, distributed energy storage, electric vehicles, and distributed wind power, the control of low-voltage distribution networks (LVDNs) has become increasingly complex. Acquiring the most recent topological structure is essential for conducting accurate analysis and real-time control of LVDNs. The signal-injection-based topology identification algorithm is favored for its speed and efficiency. This study proposes a new signal-injection-based topology identification algorithm aimed at solving the issues of reduced completeness and correctness of identification caused by missing feature signal records (FSRs). By analyzing the correlations between FSRs of different positions, the algorithm employs vertical and horizontal completion methods to effectively address missing data, combined with inclusion detection algorithms, to identify the topology of LVDNs. Based on the study of actual LVDN data, the results indicate that the algorithm not only significantly improves the completeness and correctness of topology identification for LVDNs but can also increase the number of devices in operation by evaluating the status of topological equipment, further enhancing the topology identification performance.

The article discusses issues related to the optimization of the operation of medium voltage networks, focusing on the optimization of network division points and the selection of the optimal network configuration aimed at reducing power and energy losses. The article provides a critical review of selected scientific works from recent years on the issue of network configuration optimization. The developed solution uses non-deterministic network models and statistical and probabilistic approaches. Optimization studies were carried out using heuristic optimization methods and proprietary algorithms for forecasting the load and power generated from renewable energy sources. The solution proposed in the article has many application possibilities. It can be used to optimize the location of network division points (reducing economic costs related to the modernization of network infrastructure) as well as to optimize the reconfiguration process in order to reduce power losses while maintaining voltage criteria.

Accurate forecasting of icing thickness has a great significance for ensuring the security and stability of power grid. In order to improve the forecasting accuracy, this paper proposes an icing forecasting system based on fireworks algorithm and weighted least square support vector machine (W-LSSVM). The method of fireworks algorithm is employed to select the proper input features with the purpose of eliminating the redundant influence. In addition, the aim of W-LSSVM model is to train and test the historical data-set with the selected features. The capability of this proposed icing forecasting model and framework is tested through the simulation experiments using real-world icing data from monitoring center of key laboratory of anti-ice disaster, Hunan, South China. The results show that the proposed W-LSSVM-FA method has a higher prediction accuracy and it may be a promising alternative for icing thickness forecasting.

If a clear and valid no-go for Einsteinian hidden parameters is real, it must in no way be possible to violate the CHSH with a local hidden variables based computer simulation. In the paper we show that with the use of a modied Glauber-Sudarshan method it is possible to violate the CHSH.The criterion value comes close to the quantum value and is approximately 2.4. The proof (POC) is presented with the use of an R computer program. The important snippets of the code are discussed and the complete code is presented in an appendix.

Day by day, the share of renewable energy-based power plants such as offshore wind farms and photovoltaic power plants, in the present-day power systems is escalating. Nevertheless, most of these power-producing facilities have been located quite far away from the load centers. At this stage, HVDC power systems provide satisfactory options due to qualities such as reduced line losses, substantial controllability, and environmental advantages. Nevertheless, unique converter designs are required to combine asynchronous HVDC networks with each other and with already existing high voltage alternating current (HVAC) networks. In this study, based on the above special cases, a unique DC-DC modular multilevel converter (MMC) architecture is presented that provides an excellent solution for both integrating modern asynchronous HVDC networks and integrating these modern HVDC power systems with existing asynchronous HVAC power systems. The mathematical analysis of the recommended DC-DC MMC design has been examined in detail and the power transfer between two asynchronous power grids has been realized in a simulation environment. Efficient bilateral power transmission has been made achievable by the control system. The recommended DC-DC MMC topology has shown to be a highly successful approach, in the interconnection of HVDC power systems, according to the simulation results.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

In Thailand, parking time violation is a major problem, especially for mini-marts. At present the task of detecting parking time violation is mainly conducted manually using Closed-Circuit Television (CCTV). This method requires additional human labour to track incoming and outgoing vehicles. Therefore, low cost time violation tracking is needed. To the best of our knowledge, there has not been any research for parking violation detection and tracking conducted for parking time limits. This paper introduces a novel parking time violation detection algorithm using the Yolov8 and DeepSORT tracking algorithms to track vehicles in consecutive frames. The presented parking violation tracking algorithm can provide a guideline for research in parking time violation detection.

In recent decades, a number of high-profile cases involving fraud as research misconduct have been in the media and resulted in severe consequences for those convicted. According to the increased cases of allegations and coverage in the media, this reflects a heightened awareness that fraudulent actions exist. Nonetheless, the Office of Research Integrity data suggests that despite the growth in the number of the cases of allegation there has not been a commensurate increase in findings of misconduct. The purpose of this paper is to explore misconduct to better understand what it entails. An analysis of misconduct from the perspective of the definitions of allegations and fraud of is conducted and potential frameworks for understanding both are considered. The paper considers serial-positioning effects of primacy and recency on allegation phenomena, as well as supervenience theory and contextualism as a lens for understanding fraud. Discussion of the relational semantics of the core aspects of fraud and de facto grouping of forms of misconduct. It is concluded that the interrogative pronouns of “what” and “when” could be used to categorize forms of misconduct laying the foundation for the next paper that deconstructs the definition of falsification according to the Public Health Service.

Quantum Correlations are studied extensively in quantum information domain. Entanglement Measures and Quantum Discord are good examples of these actively studied correlations. Detection of violation in Bell inequalities is also a widely active area in quantum information theory world. In this work, we revisit the problem of analyzing the behavior of quantum correlations and violation of Bell inequalities in noisy channels. We extend the problem defined in [1] by observing the changes in negativity measure, quantum discord and a modified version of Horodecki measure for violation of Bell inequalities under amplitude damping, phase damping and depolarizing channels. We report different interesting results for each of these correlations and measures. All these correlations and measures decrease under decoherence channels, but some changes are very dramatical comparing to others. We investigate also separability conditions of example studied states.

Finding sustainable renewable energy sources for energy conversion and management is still an obscure topic. This paper presents a model-based simulation for an energy conversion system using piezoelectric energy harvester (PEH) technology. A dynamic mathematical model of a PEH device consists of a piezoelectric transducer, a controlled PWM rectifier, and a closed-loop buck boost converter is developed. A piezoelectric transducer converts mechanical vibrations from a wind force into an oscillating train of electrical charges. The sinewave peak-to-peak level relationship describes the changeable values of these charges, which depend on the severity of the wind vibration. The controlled PWM rectifier, in conjunction with a closed-loop buck-boost converter, converts this train of sinewave cycles into DC voltages. The control blocks of the closed-loop buck-boost converter use the perturbation and observation (P&O) algorithm based on maximum power point tracking (MPPT), which adapts the operational voltage of the piezoelectric source to deliver the maximum power to load and improves the PEHS output voltage stability. A simulation program is employed to perform mathematical analysis on various wind vibration scenarios, piezoelectric sources without PWM converters, and piezoelectric vibration sources connected to a closed-loop P&O converter. The crucial results of this paper demonstrate that the proposed dynamic PEHS model effectively feeds low-power electronic loads by directly adjusting the output voltage level to the set voltage, even under different vibration severity levels. As a result, the proposed PEHS dynamic model serves as a guideline for researchers in the development of self-powered sensors, which contributes to understanding sustainable energy alternatives.

One of the manifestations of Lorentz invariance violation (LIV) is vacuum birefringence, which leads to an energy-dependent rotation of the polarization plane of linearly polarized photons arising from an astrophysical source. Here we use the energy-resolved polarization measurements in the prompt $\gamma$-ray emission of five bright gamma-ray bursts (GRBs) to constrain this vacuum birefringent effect. Our results show that at the 95\% confidence level, the birefringent parameter $\eta$ characterizing the broken degree of Lorentz invariance can be constrained to be $|\eta|<\mathcal{O}(10^{-15}-10^{-16})$, which represent an improvement of at least eight orders of magnitude over existing limits from multi-band optical polarization observations. Moreover, our constraints are competitive with previous best bounds from the single $\gamma$-ray polarimetry of other GRBs. We emphasize that, thanks to the adoption of the energy-resolved polarimetric data set, our results on $\eta$ are statistically more robust. Future polarization measurements of GRBs at higher energies and larger distances would further improve LIV limits through the birefringent effect.

This paper is devoted to the foundational problems of dendrogramic holographic theory (DH-theory). We use the ontic-epistemic (implicate-explicate order) methodology. The epistemic counterpart is based on representation of data by dendrograms constructed with hierarchic clustering algorithms. The ontic Universe is described as the p-adic tree; it is zero dimensional, totally disconnected, disordered, and bounded (in p-adic ultrametric). Interrelation classical-quantum loses its sharpness; generally simple dendrograms are ``more quantum’’ than complex one. We use the CHSH-inequality as a measure of quantum(-likeness). We demonstrate that it can be violated by classical experimental data represented by dendrograms. The seed of this violation is neither nonlocality nor rejection of realism. This is nonergodicity of dendrogramic time series. Generally, violation of ergodicity is one of the basic features of DH-theory. We also consider DH-theory for Minkovski geometry and monitor the dependence of CHSH-violation and nonergodicity on geometry as well as a Lorentz transformation of data.

We consider spontaneous quark transitions between the Λ0 baryon and its resonant states, and (anti)quark transitions between the neutral kaon K0 and the two heavy ηq-mesons (q = c, b). We use the measured differences in mass deficits to calculate the binding energy levels of valence c and b (anti)quarks in these transitions. In the process, we account for isospin energy release in K0 transitions and for the work done by the strong force in suppressing Coulomb repulsions in the charged Λc+-baryon. We find that the flips s→c and s¯→c¯ both release energy back to the strong field; and that the overall range of quark energy levels above their u-ground is 100-MeV wider than that of antiquark energy levels above their d¯-ground. The wider quark range stems from the flip s→b, which costs 283 MeV more (or 3× more) than the corresponding antiquark flip s¯→b¯. At the same time, transitions from the respective ground states to the s and s¯ states (or the c and c¯ states) point to a clear origin of the elusive charge-parity (CP) violation. The determined binding energy levels of (anti)quarks allow us to analyze in depth the (anti)quark transitions in Λ-baryons and B-mesons.

By using 0.35-um CMOS process, this work achieves a design of analogous band-gap reference voltage circuit with low temperature coefficient. The proposed circuit operates at 3V and generates a reference current of 44 uA. The HSPICE simulation results show the temperature coefficient of this circuit is 23 ppm/℃ at range of -10 ℃ to 100 ℃, and the line regulation (the ratio of output current variation to supply voltage variation) is estimated as 1.95 uA/V from supply voltage variation of 3 V to 5 V. The experimental chip is fabricated and measured. The circuit provides adjustable capability for output voltage among temperature variation of -10 - 100 ℃. The chip area is 534 × 695 um^2. In this new design, the operational amplifier is not necessary. The chip design effort can be great reduced.

In this review, we present the latest exclusion limits obtained with astroparticles for Lorentz Invariance Violation (LIV) in the photon sector. We discuss the techniques known as energy-dependent time delay or time lag, subluminal pair production threshold shift, superluminal photon decays and superluminal photon splitting. Perspectives for future results in LIV with the next generation of experiments are also addressed.

In this brief review, the concepts of quantum tunneling and parity violation are introduced in the context of chiral molecules. A particle moving in a double well potential provides a good model to study the behavior of chiral molecules, where the left well and right well represent the L and R enantiomers, respectively. If the model considers the quantum behavior of matter, the concept of quantum tunneling emerges, giving place to a stereomutation dynamics between left- and right-handed chiral molecules. Parity-violating interactions, like the electroweak one, can be also considered, making possible the existence of an energy difference between the L and R enantiomers, the so-called parity-violating energy difference (PVED). Here we provide a brief account of some theoretical methods usually employed to calculate this PVED, also commenting on relevant experiments devoted to experimentally detect the aforementioned PVED in chiral molecules.

Quantum Correlations are studied extensively in quantum information domain. Entanglement Measures and Quantum Discord are good examples of these actively studied correlations. Detection of violation in Bell inequalities is also a widely active area in quantum information theory world. In this work, we revisit the problem of analyzing the behavior of quantum correlations and violation of Bell inequalities in noisy channels. We extend the problem defined in a recent study by observing the changes in negativity measure, quantum discord and a modified version of Horodecki measure for violation of Bell inequalities under amplitude damping, phase damping and depolarizing channels. We report different interesting results for each of these correlations and measures. All these correlations and measures decrease under decoherence channels, but some changes are very dramatical comparing to others. We investigate also separability conditions of example studied states.

Recently, a concept known as μTRISTAN, which involves the acceleration of μ+, has been proposed. This initiative has led to considerations of a new design for a neutrino factory. Additionally, leveraging the polarization of μ+, measurements of T violation in neutrino oscillations are also being explored. In this paper, we present analytical expressions for T violation in neutrino oscillations within the framework of standard three flavor neutrino oscillations, a scenario involving nonstandard interactions, and a case of unitarity violation. We point out that examining the energy spectrum of T violation may be useful for probing new physics effects.

Theories of quantum gravity suggest that Lorentz invariance, the fundamental symmetry of the Theory of Relativity, may be broken at the Planck energy scale. While any deviation from conventional Physics must be minuscule in particular at attainable energies, this hypothesis motivates ever more sensitive tests of Lorentz symmetry. In the photon sector, astrophysical observations, in particular polarization measurements, are a very powerful tool because tiny deviations from Lorentz invariance will accumulate as photons propagate over cosmological distances. The Standard-Model Extension (SME) provides a theoretical framework in the form of an effective field theory that describes low-energy effects due to a more fundamental quantum gravity theory by adding additional terms to the Standard Model Lagrangian. These terms can be ordered by the mass dimension d of the corresponding operator and lead to a wavelength, polarization, and direction dependent phase velocity of light. In this paper, we analyze optical polarization measurements from 63 Active Galactic Nuclei (AGN) and Gamma-ray Bursts (GRBs) in order to search for Lorentz violating signals. We derive the first set limits on each of the 10 individual birefringent coefficients of the minimal SME with d = 4, with 95% confidence limits on the order of 10⁻³⁴ on the dimensionless coefficients.

The violation of Bell's theorem is a very simple way to see that there is no underlying classical interpretation of quantum mechanics. The measurements made on the photons shows that light signal (information) could travel between them, hence completely eliminating any chance that the result was due to anything other than entanglement. Entanglement has been studied extensively for understanding the mysteries of non-classical correlations between quantum systems. It was found that violation of Bell's inequalities could be trivially calculated and for sets of nonmaximally entangled states of two qubits, comparing these entanglement measures may lead to different entanglement orderings of the states. On the other hand, although it is not an entanglement measure and not monotonic under local operations, due to its ability of detecting multipartite entanglement, quantum Fisher information (QFI) has recently received an intense attraction generally with entanglement in the focus. In this work, we visit violation of Bell's inequalities problem with a different approach. Generating a thousand random quantum states and performing an optimization based on local general rotations of each qubit, we calculate the maximal QFI for each state. We analyze the maximized QFI in comparison with violation in Bell's inequalities and we make similar comparison of this violation with commonly studied entanglement measures, negativity and relative entropy of entanglement. We show that there are interesting orderings for system states.

In this work, we investigate the behaviour of relativistic quantum oscillator under the effects of Lorentz symmetry violation determined by a tensor $(K_F)_{\mu\nu\alpha\beta}$ out of the Standard Model Extension. We analyze this relativistic system under an inverse radial electric field and a constant magnetic field induced by Lorentz symmetry violation. We see that the presence of Lorentz symmetry breaking terms modified the energy spectrum of the system, and a quantum effect arise due to the dependence of the linear charge density on the quantum numbers of the system

Voltage Stability & Control, is very crucial compared to other Power System (PS) Quality and Stability issues. Long-Vertical-Power-Flows in Conventional Grids, causes voltage drops which in turn causes huge power losses, especially in the Medium Voltage (MV) and Low Voltage (LV) Distribution Networks. Such technical losses in abysmally-planned weak distribution networks, lead to substantial loss of revenues to the utility grid. Apart from classic Voltage Regulation (VR) techniques, with the rise of Distributed Generation (DG) based on Renewable Energy Sources (RES), Horizontal-Power-Flows can be introduced in the network, through various Smart Grid techniques. Coupling such sources, near load centers shall mitigate long flows from expensive conventional sources at times of huge demands, improving feeders’ Voltage Profile. This Ancillary Service of Voltage Support from DG RESs shall thereby alleviate revenue losses caused by long-power-flows in weak distribution grids. For a developing country like Pakistan, loss of revenue from an already expensive utility gives huge blow to the economy. So, a similar technique for voltage support is proposed for an 11-kV feeder, which faces similar problem, and the results are remarkable. The technique is implemented using OpenDSS Tool by modelling 3MWp PV Penetration along with some future storage.

Voltage-gated potassium (Kv) channels and hyperpolarization-activated cyclic nucleotide-gated (HCN) channels share similar structures but have opposite gating polarity. Kv channels have a strong coupling ( &gt;109) between the voltage sensor (S4) and the activation gate: when S4s are activated the gate is open to &gt;80%, but when S4s are deactivated, the gate is open &lt; 10-9 of the time. Using noise analysis, we show that the coupling between S4 and the gate is &lt; 200 in HCN channels. In addition, using voltage clamp fluorometry, locking the gate open in a Kv channel drastically altered the energetics of S4 movement. In contrast, locking the gate open or decreasing the coupling between S4 and the gate in HCN channels had only minor effects on the energetics of S4 movement, consistent with a weak coupling between S4 and the gate. We propose that this loose coupling is a prerequisite for the reversed voltage gating in HCN channels.

Due to advances in power electronics technology and the evolution of automation devices, the number of electrical devices that are sensitive to power quality is rapidly increasing, and for this reason, users are increasing their demand for high quality. To meet power quality demands, many power conversion devices are used, including dynamic voltage restorers (DVRs). DVRs are rec-ognized as devices that can effectively manage problems such as voltage segment, swells, and harmonics. DVR control requires many samples for harmonic compensation, which has the dis-advantage of being complicated to implement due to fast digital signal processing computation and the application of the cyclic discrete Fourier transform. In this paper, a high-precision DVR system configuration is proposed that compensates for harmonics using a periodically equivalent time-interval sampling technique and a novel circular structured memory filter. The proposed circular structured multi-pointer memory filter is an effective filter algorithm for high-precision input voltage measurement because it can remove noise and compensate for the delay of the phase angle of the filter in voltage measurement. A simulation and DVR prototype system was built, and the feasibility and effectiveness of the phase angle multi-filter voltage detection method and the compensation method were verified by experiments.

The escalating antibiotic crisis in Nigeria presents a critical challenge, violating fundamental human rights and ethical obligations. Skyrocketing antibiotic costs severely restrict access to essential medications, particularly for vulnerable populations. This crisis not only exacerbates health disparities but also fuels the emergence of antibiotic resistance, posing grave public health risks. Rooted in regulatory gaps, lack of transparency in drug pricing, and inadequate healthcare infrastructure, the crisis demands a comprehensive, collaborative response. Policy interventions targeting antibiotic affordability, regulatory reforms, and healthcare infrastructure investments are imperative. Upholding ethical standards and accountability mechanisms is essential to ensuring equitable access to antibiotics and safeguarding public health in Nigeria.

The formation of the required AC voltage level is currently one of the most important problems. An unstable voltage level can lead to the failure of domestic and industrial equipment, also to the appearance of a lighting equipment flicker effect, which can adversely affect the operating mode. In this regard, the development of AC voltage regulators that perform the function of stabilizers has become relevant. In turn, new topologies should be energy efficient and reliable, this can be achieved by reducing the number of semiconductor elements, which in turn will reduce losses and increase efficiency. In addition to voltage stabilization, AC voltage regulators have found application as soft-start devices for asynchronous motors, and have become competitors to frequency converters. The power level can vary from units to tens of kilowatts where such devices can be used. This paper provides a review of AC voltage regulators, which can be used both as soft starters and AC voltage stabilizers. The analysis of the circuits was carried out and the efficiency was evaluated through their total harmonic distortions (THD), power factor and efficiency coefficient. Experiments were also performed for a number of circuits, where their operating modes were evaluated. Eventually, all circuits were divided into full number of switches with two or more AC switches per phase, with a reduced number of switches, where one AC switch per phase and with low number of switches – with one complementary pair of AC switches for all three phases.

Based on the minimum conduction band edge caused by the minimum channel potential resulting from the quasi-3D scaling theory and the 3D density of state (DOS) accompanied by the Fermi-Dirac distribution function on the source and drain sides, a unified semiconductor-device-physics-based ballistic model is developed for the threshold voltage of modern multiple-gate (MG) transistors, including FinFET, W-gate MOSFET, and Nanosheet (NS) MOSFET. It is shown that the thin silicon, thin gate oxide, and high work function will alleviate the ballistic effects and resist the threshold voltage degradation. Besides, as the device dimension is further reduced to give rise to the 2D/1D DOS, the lowest conduction band edge is hence increased to resist the threshold voltage degradation. The nanosheet MOSFET exhibits the largest threshold voltage among the three transistors due to the smallest minimum conduction band edge caused by the quasi-3D minimum channel potential. Compared to P-type MOSFET (P-FET), the N-FET shows more threshold voltage because the electron has a more effective mass than the hole

Structural biology has a strong interest in ion channels, a diverse group of membrane proteins. This group has long remained difficult to study, but much progress has been made in recent decades with improvements in biochemical methods and computational procedures. Voltage-gated ion channels undergo conformational changes upon functioning, and multiple models of activation mechanisms were proposed based on experimental data. This review focuses on the structural studies of the functioning of voltage-gated ion channels, which are accompanied by conformational changes in proteins, and the methodological advances that allow their observation. Modern experimental methods that allow obtaining ion channel proteins in specific functional states are discussed, including cryoelectron microscopy and cryoelectron tomography. Finally, new algorithms for studying the conformational mobility of proteins have been developed, which help to better understand the mechanisms of ion channel domain movements.

This paper addresses the effects of electric power quality on robotics operation. A general overview is reported to highlight the main characteristics of electric power quality and their effects on a powered system by considering an end-users viewpoint. Then, authors outline the influence of voltage dip effects by focusing at robotic grasping applications. A specific case of study is reported as referring to LARM Hand IV, a three-fingers robotic hand, which has been designed and built at LARM in Cassino. A dedicated test rig has been settled up for generating predefined voltage dips. Experimental tests are carried out for evaluating the effects of different types of voltage dips on the grasping of objects.

The basic constitutional freedoms and rights of a person and citizen are in principle unlimited: the full scope of their exercise is the rule, and the restriction determined by law can only be an exception based on explicit constitutional authority and the legitimate aim of the restriction determined by the Constitution. That being so, the restrictions - in addition to being based on constitutional authority and pursuing constitutional objectives - should be commensurate with the needs to achieve these objectives. This means that restrictive legal rules must be suitable for achieving the legitimate aim pursued, must not be stricter than necessary and must be balanced between the constitutionally guaranteed subjective right of the individual and the interests of society. In this scholar paper, the authors point out the economic and legal consequences of the violation of individual privacy and data protection rights caused by the public disclosure of personal data of people who, at a certain time, were obliged to self-isolate due to suspicion of Covid-19 virus infection.

In this work, linear confinement of a relativistic scalar particle under the effects of Lorentz symmetry violation is investigated. We introduce a scalar potential by modifying the mass via transformation M → M + S(r) in the wave equation, and analyze the effects on the eigenvalues and the wave function. We see that the solution of the bound state to the wave equation can be achieved, and the energy eigenvalues and the wave function modified by the Lorentz symmetry breaking parameters as well as potential

Accurate and prompt determination of fire types is essential for effective firefighting and reducing damages. However, traditional methods such as smoke detection, visual analysis, and wireless signals pose unavailability in identifying fire types. This paper introduces FireSonic, an acoustic sensing system that leverages commercial speakers and microphones to actively probe the fire using acoustic signals, effectively identifying indoor fire types. By incorporating beamforming technology, FireSonic first enhances signal clarity and reliability, thus mitigating signal attenuation and distortion. To establish a reliable correlation between fire types and sound propagation, FireSonic quantifies the Heat Release Rate (HRR) of flames by analyzing the relationship between fire heated areas and sound wave propagation delays. Furthermore, the system extracts spatiotemporal features related to fire from channel measurements. Experimental results demonstrate that FireSonic attains an average fire type classification accuracy of 95.5% and a detection latency of less than 400 ms, satisfying the requirements for real-time monitoring. This system significantly enhances the formulation of targeted firefighting strategies, boosting fire response effectiveness and public safety.

In this paper, modelling designing and simulation of a simple voltage amplidyne system is done using robust control theory. In order to increase the performance of the voltage amplidyne system with H ∞ optimal control synthesis and H ∞ optimal control synthesis via ∞-iteration controllers are used. The open loop response of the voltage amplidyne system shows that the system can amplify the input 7 times. Comparison of the voltage amplidyne system with H ∞ optimal control synthesis and H ∞ optimal control synthesis via ∞-iteration controllers to track a desired step input have been done. Finally, the comparative simulation results prove the effectiveness of the proposed voltage amplidyne system with H ∞ optimal control synthesis controller in improving the percentage overshoot and the settling time.

The outer membrane of Gram-negative bacteria contains a variety of pore-forming structures collectively referred to as porins. Some of these are voltage-dependent, but weakly so, closing at high voltages. Triplin, a novel bacterial pore-former, is a three-pore structure, highly voltage dependent, with a complex gating process. The three pores close sequentially: pore 1 at positive potentials, 2 at negative and 3 at positive. A positive domain containing 14 positive charges (the voltage sensor) translocates through the membrane during the closing process and the translocation is proposed to take place by the domain entering the pore and thus blocking it resulting in the closed conformation. This mechanism of pore closure is supported by kinetic measurements that show that in the closing process the voltage sensor travels through most of the transmembrane voltage before reaching the energy barrier. Voltage-dependent blockage of the pores by polyarginine but not by a 500 fold higher concentrations of polylysine, is consistent with the model of pore closure, with the sensor consisting mainly of arginine residues, and with the presence, in each pore, of a complementary surface that serves as a binding site for the sensor.

In this paper, we discuss voltage control method for buck converter operating in continuous conduction mode (CCM) using analog feedback system. The aim of this work is to control the output voltage of a buck converter during the variation in load current. This is obtained using analog feedback made with operational amplifier (Opamp). However, the same technique can be applied to other DC-DC converters (e.g boost, buck-boost, cuk converter, etc) in CCM mode, but for the purpose of analysis buck converter is chosen as an example.

Nowadays, in low voltage (LV) electric distribution networks (EDNs), the Distribution Network Operators (DNOs) are encountering a high number of connected small-scale distributed generation units, mainly photovoltaic (PV) prosumers. The irregular behavior of the prosumers, together with the uncertainty degree of the requested and injected powers associated with all end-users from the LV EDN, can cause voltage variations with violations of the allowable limits. In this context, the paper developed an efficient and resilient expert system integrating the rule-based reasoning applied to the On-load Tap Changer (OLTC)-fitted transformer to improve the efficiency of the voltage control in the PV-rich LV EDNs. An in-depth analysis based on 75 scenarios, resulting from the combinations of three indicators: the penetration degree of the PV prosumers, consumption evolution associated with the consumers, and energy production of the PV systems, has been performed to demonstrate the efficiency of the proposed expert system in an LV EDN from a rural area belonging to a Romanian DNO. The success rate of the expert system has been 86.7% (65 out of 75 scenarios didn't have voltage issues, all values being between the allowable limits in 100% of the time slots associated with the analyzed period). For the other scenarios (representing 13.3%), the values have been inside the range [-10%, +10%] at least 95% of the time slots, according to the European Power Quality Standard, and for the rest of the time slots up to 100% being very close to the upper and lower limits of the range, with highly mitigating of the voltage variations.

We investigate a scalar particle under Lorentz symmetry breaking effects determined by a tensor out of the Standard Model Extension (SME) in the presence of a Cornell-type potential by modifying the mass term M → M +S in the KG-equation. The field configuration is such that a Coulomb-type radial electric field and a constant magnetic field can be induced by Lorentz symmetry violation, and analyze the behaviour of a scalar particle. One can see that the bound states solution to the KG-equation under the consider effects can be achieved, and a quantum effect characterized by the dependence of charge density distribution parameter on the quantum numbers of the system is observed.

The popular motor drive systems with a single two-level voltage source inverter (VSI) have one main problem that is the occurrence of the common-mode voltage (CMV), which is an effect of the electromagnetic interference, shaft voltage, bearing currents, leakage current. These cause the high stress, increasung temperature and early mechanical failure in machine. To overcome this problem, the technology of the dual two-level VSI fed open-end three-phase ac loads is now available to eliminate the CMV at the ac/induction motor load with the 120-degree modulation technique for controlling each inverter. In this paper, the discontinuous space vector modulation (DSVM) schemes are proposed and applied for the dual two-level VSI fed open-end load. It is based on the 120-degree modulation technique by using only 12 active voltage vectors and the 10 zero voltage vectors from the total 64 voltage vectors along with the different five-segment swicthing sequence designs with centralizing pulse width modulation technqiue in order to not only cancel the CMV in the ac load, but also reduce the switching number/switching loss of the conversion system. Among the various DSVM schemes, their performances are compared in this paper, such as the number of the switching, the step and peak value of the CMV in each inverter, and the quality of the output waveform, etc. The details of the verfication and comparison are carried out by simulation using Matlab/Simulink software.

A scientific consensus is emerging on the benefits of dc distribution in medium voltage power systems of ships and cities. At least 50% space savings and increased power transfer capacity are estimated with enhanced voltage dc operation of electric cables. The goal of this research is to contribute to developing the empirical knowledge on the insulation performance in order to validate the feasibility of such anticipated gains of dc versus ac, and to determine the comparative impact of different operational conditions from a component engineering point of view. The partial discharge (PD) activity in cables is measured under ac and dc conditions as an indicator of insulation performance. Specifically, PDs in defects at the semicon-insulation interface are studied in terms of inception voltage, repetition rate and discharge magnitude. Empirical understanding is drawn for operating voltage and frequency dependence of the discharge behavior in such voids in the range of 10 to 20\,kV and 0 to 0.1\,Hz, respectively. The change in PD activity with void evolution is explored.

Besides the increase in global energy demand, access to clean energy, reduction in greenhouse gas emissions caused by conventional power generation sources, energy security, and availability of electricity in remote villages in emerging nations are some of the factors that foster the use of renewable energy sources (RESs) in generating electricity. One of the aims of initiating microgrids (MGs) is to maximize the benefits of RES and alleviate the associated grid integration issues. Microgrids are made up of RES connected to electrical loads within clearly delineated electrical limits that operate as individual controllable units on the electrical network. It can operate in-dependently as well as in connection with the grid. The paper presents an overview of microgrids and investigates the system's performance when connected to and disconnected from the grid. Furthermore, in both modes of operation, the functioning and behavior of system components such as the bidirectional DC-DC converter and energy storage system (ESS) were evaluated. The architecture of the proposed microgrid consists of a small hydropower plant, a wind farm, and a battery energy storage system (BESS). The microgrid under investigation is modeled and simu-lated using MATLAB and Simulink.

Psychiatric disorders are mental, behavioral or emotional disorders. These conditions are prevalent, one in four adults suffer from any type of psychiatric disorders world-wide. It has always been observed that psychiatric disorders have a genetic component, however new methods to sequence full genomes of large cohorts have identified with high precision genetic risk loci for these conditions. Psychiatric disorders include, but are not limited to, bipolar disorder, schizophrenia, autism spectrum disorder, anxiety disorders, major depressive disorder, and attention-deficit and hyperactivity disorder. Several risk loci for psychiatric disorders fall within genes that encode for voltage-gated calcium channels (Ca_Vs). Calcium entering through Ca_Vs is key for multiple neuronal processes. In this review, we will summarize recent findings that link Ca_Vs and their auxiliary subunits to psychiatric disorders. First, we will provide a general overview of Ca_Vs structure, classification, function, expression and pharmacology. Next, we will summarize tools and databases to study risk loci associated with psychiatric disorders. We will examine functional studies of risk variations in Ca_V genes when available. We will review pharmacological evidence of the use of Ca_V modulators to treat psychiatric disorders. Our review will be of interest for those studying pathophysiological aspects of Ca_Vs.

Normally, the Nernst voltage calculated from the concentration of the reaction gas in the flow channel is considered to be the ideal voltage (reversible voltage) of the oxyhydrogen fuel cell, but actually it will cause a concentration gradient when the reaction gas flows from the flow channel through the gas diffusion layer to the catalyst layer. The Nernst voltage loss in fuel cells in most of the current literature is thought to be due to the difference in concentration of reaction gas in the flow channel and concentration of reaction gas on the catalyst layer at the time when the high net current density is generated. Based on the Butler-Volmer equation in oxyhydrogen fuel cell, this paper demonstrates that the Nernst voltage loss is caused by the concentration difference of reaction gas in flow channel and on the catalytic layer at the time when equilibrium potential (Galvanic potential) of each electrode is generated.

We analyze the expected arrival time spectrum of supernova neutrinos using simulated luminosity and computing the expected number of events in future detectors such as the DUNE Far Detector and Hyper-Kamiokande. We develop a general method using minimum square statistics that can compute the sensitivity to any variable affecting neutrino time of flight. We apply this method in two different situations: First, we compare the time spectrum changes due to different neutrino mass values to put limits in electron (anti)neutrino effective mass. Second, we constrain Lorentz Invariance Violation through the mass scale, MQG, at which it would occur. We consider two main neutrino detection techniques: 1. DUNE-like liquid argon TPC, for which the main detection channel is νe+40Ar→e−+40K*, related to the supernova neutronization burst, and 2. HyperK-like water Cherenkov detector, for which ν¯e+p→e++n is the main detection channel. We consider a fixed supernova distance of 10 kpc and two different masses of the progenitor star: (i) 15 M⊙ with neutrino emission time up to 0.3 s and (ii) 11.2 M⊙ with neutrino emission time up to 10 s. The best mass limits at 3σ are of O(1) eV. For νe, the best limit comes from a DUNE-like detector if the mass ordering happens to be inverted. For ν¯e, the best limit comes from a HyperK-like detector. The best limit for the Lorentz Invariance Violation mass scale at 3σ level, considering superluminal or subluminal effect, is MQG≳1013 GeV (MQG≳5×105 GeV) for linear (quadratic) energy dependence.

In this work, we investigate the behaviour of a relativistic scalar particle in the background of the Lorentz symmetry violation determined by a tensor (KF)µναβ out of the Standard Model Extension. A linear electric field and a uniform magnetic can be induced by the violation of the Lorentz symmetry breaking effects, and analyze the behaviour of the scalar particle. We see that the analytical solution to the KG-equation can be achieved, and a quantum effect characterized by the dependence of the magnetic field on the quantum numbers is observed

Larrea tridentata is an endemic plant from the Mexican highlands used in traditional medicine to treat hypertension and kidney stones, among many ailments. This study evaluated a vasorelaxant compound: 5- Hydroxy-2-(4-hydroxy-3-methoxyphenyl)-6,7,8-trimethoxy-4H-1-benzopyran-4-one (also known as 8-Methoxycirsilineol: 8-M) which we purified from an extract of this plant. Mesenteric artery rings were isolated from male guinea pigs for isometric force measurements. Freshly isolated smooth muscle cells from mesenteric artery were used for ionic current measurement for calcium and potassium. 10 μM 8-M completely relaxed vascular rings contracted with phenylephrine in a dose-dependent fashion with an EC50 = 4.26 ± 1.16 10-6 M and 4.56 ± 1.64 10-6 M for endothelium intact and endothelium-free tissue, respectively. The relaxant effect of 8-M was not affected by maximal doses of nifedipine, verapamil or iberiotoxin. Nevertheless, the relaxant effect was partially abolished by addition of 10 mM Tetraethylammonium (TEA). In accordance to this, calcium currents evoked by depolarization were not affected by 8-M, whereas TEA-sensitive potassium currents, were increased upon its addition. Vasorelaxation due to 8-M is partly due to activation of KV currents in an endothelium independent mode.

The paper proposes an innovative solution for managing and ensuring high energy efficiency of power supply systems at high non-linear loads. This is realized by maintaining optimal value of reliability indicators and high quality of power supply. The validation is carried out using analyzes and tests of quality of electromagnetic compatibility (EMC) for increased number of powered frequency converters. It has been proven that the effective use and reduction of energy consumption can be achieved thanks to the unique technological features of the employed electrical devices. This enables a normal operation of the system with decreased power and adequate control of energy processes. The problem of predicting power losses under changing conditions in a decentralized electrical network has been solved based on the theory of electromagnetic compatibility. The influence of the mains mode parameters and the indices of instantaneous distortion of current and voltage waveforms caused by the operation of converters on the resonance phenomena in power supply systems were investigated. Recommendations were developed for the selection of proper parameters of compensators for 6-10 kV and 0.4-0.66 kV circuits based on the analysis of the optimization problem when minimizing active power losses. Results of our findings may aid parties involved in designing and maintaining power networks in various applications, such as mines, etc.

Voltage sags can cause the interruption of power supply and can negatively affect operations of customers. In this paper, the authors study the impact of battery energy storage systems (BESS) on voltage sags. A stochastic method of fault positions is used. Faults of various types are simulated and voltages are recorded. Firstly, with the BESS integrated into the network, there are higher residual voltages, fewer voltage sags and less expected critical voltage loss. Secondly, if the BESS converter power factor is reduced, recorded residual voltages are higher, voltage sags are fewer, and the number of expected critical voltage sags is lower. Finally, when three BESS converter control modes, namely constant voltage, constant power factor, and constant reactive power, were assessed, results showed similar voltage sag performances for constant power factor and constant reactive power modes. Furthermore, operating in constant voltage control outperformed the other two modes as it resulted in higher residual voltages, a lower number of voltage sags, and fewer expected critical voltage sags. The paper has demonstrated that the BESS can improve voltage sag performance. In addition, the power factor of the BESS converter and the mode of operation of the converter can influence the magnitude of the voltage sag performance improvement.

Preclinical evidence suggests that voltage gradients can act as a kind of top-down master regulator during embryogenesis and orchestrate downstream molecular-genetic pathways during organ regeneration or repair. Moreover, electrical stimulation shifts response to injury towards regeneration instead of healing or scarring. Cancer and embryogenesis not only share common phenotypical features, but also commonly upregulated molecular pathways. Ion channel activity is directly or indirectly linked to the pathogenesis of cancer hallmarks, while experimental and clinical studies suggest that their modulation may exert antitumor effects. A large recent clinical trial served as a proof-of-principle for the benefit of preoperative use of topical sodium channel blockade as a potential anticancer strategy against early human breast cancers. Apart from the obvious importance in perioperative medicine, it calls for the planning of further carefully designed clinical trials to expand on the concept of ion channels as tumor drivers.

Three-phase AC electric arc furnace (EAF) is a typical non-linear load, causing many power quality problems. Most of the researches on the voltage problems of EAF mainly focus on the voltage fluctuation, and less on the transient voltage problems caused by EAF short circuit and open circuit. In this paper, the relationship between voltage and current of EAF is obtained by combining hyperbolic function and exponential function, then the white noise and chaotic circuit are added to establish the EAF model which is suitable for the study of voltage fluctuation and transient voltage. This paper analyzes the causes of the transient voltage problem of the EAF, calculates the short-circuit current, reactive impact and the influence on voltage at the point of common coupling (PCC) in the three-phase short-circuit of the EAF, and compares the calculation results with the simulation results to prove the accuracy of this model. The results show that the reactive impact of three-phase short circuit is about twice as much as that of normal operation of EAF, resulting in about 30% voltage sag at the PCC, which is very unfavorable to the power grid. This paper provides reference for transient power quality evaluation and dynamic reactive power compensation of EAF.

We communicate the theoretical results in the study of utilizing the quantum phenomena in optical current for quantum computation in the context of high precision voltage measurements. These results can be used around computation by quantum sampling and quantum communication as the basis for further research and physical implementations. We propose a Main Optical Setup (MOS) for such computation which allows to make a superstructure to implement specific computations and algorithms. To create MOS we used the nonlinear units (e.g., beta- barium borate crystal), arranged in series, powered with pulsed laser pump, and ended with the beam splitter to generate the output state of a number of entangled photon pairs. The computation is made by propagation of entanglement with beam splitters applied crossword and adjustable phase shifters that are tools for parameter steering. We show how to implement the series of cosine-based components on the example of two-component case. The results opens a broad area for future research in the area of building quantum optimizer using the quantum sampling methods and in the area of high precision temporal measurement of voltage, which is the important process for building high-fidelity devices.

Power quality is a major concern in electrical power systems. The power quality disturbances such as sags, swells, harmonic distortion and other interruptions have impact on the electrical devices and machines and in severe cases can cause serious damages. Therefore it is required to recognize and compensate all types of disturbances at an earliest to ensure normal and efficient operation of the power system. To solve these problems, many types of power devices are used. At the present time, one of those devices, Dynamic Voltage Restorer (DVR) is the most efficient and effective device used in power distribution system. In this paper, design and modeling of a new structure of multifunctional DVR for voltage correction is presented. The performance of the device under different conditions such as voltage swell, voltage sag due to symmetrical and unsymmetrical short circuit, starting of motors, and voltage distortion are described. Simulation result shows the superior capability of proposed DVR to improve power quality under different operating conditions. The proposed new DVR controller is able to detect the voltage disturbances and control the converter to inject appropriate voltages independently for each phase and compensate to load voltage through three single- phase transformers.

Wind power generation is one of the mainstream renewable energy resources. Voltage stability is as important as the frequency stability of a power system with a high penetration of wind power generation. The advantages of high-voltage direct current (HVDC) transmission systems become more significant with the increase of both installed capacity and transmission distance in offshore wind farms. Therefore, this study discusses about various voltage control methods for wind turbines and HVDC transmission systems. First, various voltage control methods of a wind farm were introduced, and they include QV control and voltage droop control. The reactive power of a wind turbine varies with active power, while the active power from each wind turbine may be different owing to wake effects. Thus, QV and voltage droop control with varying gain values were also discussed in this paper. Next, the voltage control methods for a HVDC transmission system, such as power factor control, voltage control, and Vac-Q control, are also summarized and tested in this study. When a three-phase short circuit fault occurs or a suddan reactive power load increases, the system voltage would drop immediately. Thus, various voltage control methods for wind turbines or HVDC can make the system's transient response more stable. Therefore, this study implemented the simulation scenarios, including a three-phase short circuit fault at the point of common coupling (PCC) or a sudden increase of reactive power load, and adopted various voltage control methods, which aims to verify whether additional voltage control methods are effective to improve the performance of transient voltage.

During recent decades, contextual computing applications have emerged in the field of healthcare and particularly in the field of telemonitoring of patients suffering from chronic obstructive pulmonary disease (COPD). According to WHO rankings, chronic obstructive pulmonary disease (COPD) is the third leading cause of death worldwide. Various research works are therefore carried out to improve the health of patients and the monitoring of patients in the comfort of their home environment. To this end, several telemonitoring systems are designed to COPD patients. These systems are connected to health center. Emergency physicians follow the patients subscribed to these systems remotely. These systems focus mainly on prediction, decision-making and the requirements of the healthcare profession, and do not address the quality control aspects of services or QoS based on service level agreements (SLAs). This situation can be dangerous for patients in case of extreme exacerbation of COPD patients. For example, the unavailability of the monitoring system can lead to the death of the patient because the emergency physician could not have access to the patient's data in real time in the context of COPD Patient Monitoring. In addition, Remote medical monitoring platforms are manipulating large volumes of data and the risks of data lost or data quality are real. It is therefore important to have the mechanisms to continuously improve the quality of service of these monitoring platforms in general and COPD patients particularly. In this article, we propose an ontology that uses SLA information from COPD monitoring platforms with dynamic data from the patient context. The purpose of this article is to propose a dynamic mechanism model for evaluating SLA violations. This solution allows retrieving knowledge from the main items of the SLA document based on XML and the COPD patient context data dynamically from a COPD SLA ontology. These data retrieved in real time allow the calculation of SLO-based metrics and display a SLA template available on the supplier and consumer interfaces. The information of the SLA violation control Interface changes dynamically depending the context-aware system and SLA document data. The SLA parties can dynamically control their Key Performance Indicators (KPI) Target.

The purpose of this paper is to critique the definition of falsification as research misconduct according to the Public Health Service (PHS) in order to better understand what it entails. In support of this purpose, the approach decided upon for analysis was philosophical including framing the issue borrowing from both mereological and epistemological perspectives. Through the consideration given to parthood relations of mereology, we gained insight from a cognitive imperfection standpoint about similarities that exist between the epistemic constraints on knowledge and the nature of violations concerning research misconduct. Findings from the examination of a case study include the significance of accuracy in representation in falsification as misconduct and the core dimensions comprising an instance of falsification, which are Deliberateness, Alteration, and Inclusion. Given that either behavior or actions must occur that violate these three aspects in order to qualify as an instance of misconduct under falsification, the author proposes that, at a minimum, any revisions made to the definition of falsification stipulate what he refers to as the Violation Imperative.

This work presents a new algorithm to resolve the problem of distribution network reconfiguration using the Tabu Search metaheuristic and voltage drop. The proposed method presents a different way to obtain the initial solution using the voltage drop, as well as a new way to generate a neighborhood of candidate solutions, based on randomness and the voltage drop, to perform a smooth and steady descent execution of the algorithm. The proposed algorithm has the main objective to reduce the active power losses in distribution networks, but it also achieves an refinement in the voltage profile. The proposed method was tested in two distribution systems, the 33-Bus and 94-Bus systems, commonly found and tested in the literature. The results of the tests show that the proposed method presents a low computational cost, achieves good solutions, and is better than the other methods found in the literature.

The general circuit topology and principles of low-noise high-voltage power supply are investigated to meet the requirements of the high-voltage bias application in air kerma meters. Two topologies, flyback converter and Royer converter are simulated using SPICE simulation program. The simulation results indicate that the circuit structure of the Royer converter is more complex, but it obtains lower output high voltage noise. While we develop an adjustable high-voltage power supply according to the circuit structure of the Royer converter, and tested it to ensure the design requirements for continuously adjustable output high-voltage linearity. The test results show that the linear adjustment rate is not more than ±0.0025%, the load regulation rate is less than ±0.1%, and the output ripple noise voltage percentage is less than 0.01%. These tested performance make it more suitable for accurate nuclear measurements.

In this paper consider the circuitry of voltage followers (VF) with unity-gain, intended for practical use in active Sallen-Key RC-filters (LPF, HPF, BPF, RF). The results of research and computer modeling of radiation-resistant and low-temperature VF in the LTSpice environment on models of CJFET transistors operating under the influence of neutron flux up to 10e14 n/cm2 and cryogenic temperatures up to -197°C are presented.

Increasing demand for electricity and modernization of power systems within competitive markets induce power systems to operate close to their stability limits. Therefore, a power system continuous monitoring and control by using voltage stability indices are known exigence. This is the first-ever effort, examined more than 40 voltage stability indices thorough an exhaustive study based in on their formulation, application, performance, and assessment measures. Which is conducted based on a logical and chronological order considering the most recent worldwide applied voltage stability indices. However, the generalizability of such an immense diversity of these indices in term of multivariable objectives subjects to a certain limitation to summate into a deciphered outcome. Despite all these obstacles, this study systematically reviews available indices in the literature within the past three decades to set out an integrated knowledge with an insight up-to-date exposition. That followed with a comparative analysis in term of their similarity, functionality, applicability, formulation, merit, demerit, and overall performances. Also, a broad categorization of voltage stability indices is addressed. This study with an immediate implication in practice as an exhaustive roadmap can be counted a planning and operation reference in the context of voltage stability for students, researchers, scholars, and practitioners.

The relativistic quantum motion of a scalar particle under the effects of violation of the Lorentz symmetry in the presence of a linear confining potential is investigated. We see that the solution of the bound state to the modified Klein-Gordon equation can be obtained and a quantum effect characterized by the dependence of the magnetic field on the quantum numbers of the system is observed

Traditional potential transformers have problems of large volume, difficulty in insulation, iron core saturation, ferroresonance overvoltage and poor transient response characteristics. The voltage sensor based on the principle of electric field coupling and differential input structure does not need to contact the measured object or ground, and can avoid the above problems. However, it requires a sufficiently high capacitance between the differential electrodes to obtain sufficient accuracy and a high voltage division ratio. The existing method of using mutual capacitance between the differential electrodes will cause many problems and fail to meet the practical needs. To solve the above problems, this paper innovatively uses multi-layer ceramic capacitor to replace the mutual capacitance and designs a new type of voltage sensor. In addition, by using single bypass small resistance grounding method to increase the input impedance of the differential signal processing circuit, error of the sensor is further reduced. The experimental results show that the sensor has excellent accuracy and great transient response characteristics. The ratio error under power frequency is within ±0.5% and the phase error is within 1. The ratio error in the range of 500 Hz∼30 kHz is within ±5% and the phase error is within 5. Moreover, it has the advantages of low cost, miniaturization, flexible shape and easy to adjust the voltage division ratio. These characteristics indicate that the sensor has good voltage measurement and sensor network potential.

The relativistic quantum dynamics of a spin-0 scalar particle under the effects of the violation of Lorentz symmetry in the presence of a non-electromagnetic potential is analyzed. The central potential induced by the Lorentz symmetry violation is a linear electric and constant magnetic field and, analyze the effects on the eigenvalues and the wave function. We see there is a dependence of the linear charge density on the quantum numbers of the system

Resonance inductive coupling is widely used for wireless power transfer (WPT) in medical applications. In this paper, we analyze the LCL-compensated WPT structure and propose a novel constant voltage transmission system based on gain estimation, without any extra feedback from the receiver. The system is capable for amplitude-modulated implant neural stimulation where the load impedance and the coupling coefficient are both variable. Compared to existing methods for constant voltage transmission, our approach offers advantages in compact size and the compatibility with the industrial, scientific and medical (ISM) band. We validate the load-independent resonant characteristic and the feasibility of constant voltage transmission using an experimental prototype working at 6.78MHz. Finally, we discuss the structure of the implant stimulator and methods of applying the proposed WPT system.

A novel low-power MOS-only voltage reference is presented. The Enz-Krummenacher-Vittoz (EKV) model is adopted to provide a new perspective on the operating principle. The normalized charge density, introduced as a new variable, serves as an indicator when trimming the output temperature coefficient. The proposed voltage reference consists of a specific current generator and a 5-bit trimmable load. Thanks to the well-match between the current source stage and the output stage, the non-linear temperature dependence of carrier mobility is automatically canceled out. The circuit is designed in 55 nm COMS technology. The operating temperature ranges from -40 ∘C to 120 ∘C. The average temperature coefficient of the output voltage can be reduced to 21.7 ppm/∘C by trimming. The power consumption is only 23.2 nW with a supply voltage of 0.8 V. The line sensitivity and the power supply rejection ratio at 100 Hz are 0.011 %/V and -89 dB respectively.

The quickest and easiest way to avoid greenhouse gas (GHG) emissions is to purchase renewable electricity and offset the remaining emissions. However, the industrial sector’s electricity needs already exceed renewable electricity generation. Moreover, electricity accounts for only one third of the industry’s energy needs. Simultaneously, the advance of sectoral coupling and the decarbonisation of industrial processes, as well as the desire to rapidly decrease dependence on fossil fuels, are creating significant additional demand for renewable energy. Neither existing nor planned generation and transmission infrastructure will suffice to meet the expected short-term demand. Based on survey data from the German Industry Energy Efficiency Index, this article therefore examines the share of GHG savings that companies intend to achieve on- and off-site. Understanding how much additional generation and transmission capacity is needed by the industry to decarbonise and by when is crucial to identify and address the extent of excess demand. On average, companies plan to avoid 22 % of their 2019 emissions by 2025 and 27 % by 2030, primarily through on-site measures. In combination with the extrapolation of the entire industry’s needs for off-site capacity, the data calls for a rapid expansion of planning authority and green generation capacities.

This paper presents a comprehensive review that highlights the characteristics of non-isolated step-up converters based on high boost voltage lifting techniques. The paper categorises the high boost techniques: multistage/multilevel, switched capacitor, voltage multiplier, voltage lift, switched inductor, and magnetic coupling. The paper also discusses in detail the advantages and disadvantages for each category such as cost, complexity, power density, reliability and efficiency. The number of passive and active components, voltage gain, voltage stress, switching frequency, efficiency and power rating are also compared. Although the paper considers coupling inductors in the context of the non-isolated converter, the focus of the entire article is on the non-isolated high voltage step-up techniques. The key contribution in this paper is the review of high boosting techniques rather than the DC /DC converters. This allows divergence of new ideas and new power converters that will help provide highly efficient and flexible power converters for several applications where the sending end voltage is very low as photovoltaic systems. In addition, many applications and control techniques of DC/DC converters are summarised in this paper.

This paper reports a new control strategy to improve sharing of unbalanced currents in islanded LV microgrids. This technique provides fast and effective sharing of positive-, negative- and zero-sequence currents, and is the first example of zero-sequence current sharing in the literature. The controllers are designed in the stationary frame. The control structure consists of four loops; 1)~the current controller; 2)~the voltage controller; 3)~the droop controller and the 4)~negative and zero sequence current controllers. The output current is considered unknown for the controller and is added to the control system as a disturbance. The proposed controller features a high gain in fundamental and harmonic frequencies, hence a good voltage quality is obtained in the presence of unbalanced and nonlinear loads. To this aim, a proportional-resonant (PR) controller is adopted as the current controller. By using a multi-resonant controller as current controller, a unified control structure is obtained which is suitable for both grid-connected and islanded modes. The voltage controller is designed using a resonant controller so that the voltage can have low VUF and THD in the presence of unbalanced and nonlinear loads. Furthermore, in this paper droop method is applied to the control structure to share real and reactive powers. Simulation studies show that the conventional droop method cannot share the oscillatory part of the output power that is due to the presence of unbalanced loads in the microgrid. This paper relies on using zero and negative sequence virtual impedance controller to share the oscillatory part of output power. By using zero-sequence virtual impedance controller (ZSVIC) and negative-sequence virtual impedance controller (NSVIC), the zero and negative sequence currents in the microgrid are controlled and shared effectively. By compensating zero- and negative-sequence currents locally, the flow of these currents in the microgrid is minimized, and the overall power quality of the islanded LV microgrid is improved.

We study the effect of the generation of the mechanical transverse wave (MTW)　travelling in the opposite direction (OD) to a moving medium (MM) on the relativistic energy conservation law (RECL). From the viewpoint of the relativity of simultaneity (RS), the time on the coordinate coinciding with the advance end of the wave (AEW) travelling toward the rear of the MM passes faster than that on the coordinate coinciding with the wave source (WS). Then the AEW in the MM travels forward compared to that in the rest frame of reference (RFR) which is stationary relative to the medium when the time on the coordinate coinciding with the WS is same for each inertial frame of reference (IFR). Hence, the coordinate interval (CI) between the AEW and WS in the MM is observed to be larger than that between them in the RFR. We show that this difference holds true for the CI of any portion having transverse velocities mutually converted by the Lorentz transformation (LT). This difference in the CI leads to that in the rest mass (RM). We demonstrate that the RM included in wave motion (WM) in the MM is larger than one included in WM in the RFR when comparing the portions having transverse velocities mutually converted by the LT. This relation holds true for all portions in WM. Therefore, the total coordinate interval of the portion (CIP) and total RM (TRM) included in WM in the MM (WMMM) are large compared to them included in WM in the RFR. Furthermore, we compare the relativistic kinetic energy (RKE) of the MTW travelling in the OD to the MM (ODMM) with that of the MTW propagating in the direction vertical to the moving direction of the medium. We prove that the CIP and RM included in the former MTW are larger than them included in the latter MTW when comparing each portion with the same transverse velocity (TV). Moreover, the total CIP and TRM included in the former MTW are also large compared to them included in the latter MTW. The reason for these is that the latter CIP and RM are equal to them in the RFR when comparing the portions having transverse velocities mutually converted by the LT. On the other hand, the energy supplied to generate each MTW is the same. From these, we demonstrate that the RKE of the MTW travelling in the ODMM can be larger than the total relativistic energy (TRE) of the MTW propagating in the direction vertical to the moving direction of the medium. Consequently, we propose a violation of the RECL and Einstein’s principle of relativity (EPR) because the TRE is not necessarily conserved in the IFR in which the medium is moving.

Concern about the planet's future has motivated governments around the world to adopt policies that promote more responsible energy consumption. Reducing emissions of the principal cause of climate change man-made greenhouse gases requires greater system efficiency and the utilization of renewable energy sources. The generation of electricity is the single largest source of hazardous pollutants, followed by the transportation sector. This is true due to the extreme reliance on petroleum and its derivatives that these industries have. Electric mobility is receiving more attention from businesses, governments, and academic institutions as a means to reduce the negative impacts of current energy consumption. Without measures to address common technical issues, electric vehicles would strain electrical infrastructure. In order to determine the best strategy for switching operations and feeder reconfiguration, this research presents a helpful hybrid genetic algorithm particle swarm optimization (HGAPSO) method. Meet transmission limits while decreasing real power losses and enhancing the system's bus voltage profile. The effects of HGAPSO on power losses and voltage distributions in the network are analyzed. Then, a report is produced contrasting GA and PSO. This cross-breeding of GA and PSO led to HGAPSO. This important problem can be solved more effectively with the use of new or improved algorithms. To find the optimal reconfiguration and properly rearrange transmission network interconnection, it employs a plethora of heuristic optimization algorithms. The objective is to limit bus voltage variations while maintaining the system's radial topology and minimizing power usage. The reliability and performance of the procedure were evaluated using MATLAB's IEEE 33-bus communication network. The outcomes demonstrate the effectiveness of the proposed technique, which cuts down on power waste during standalone runs and speeds up the processing time.

Wenchuan earthquake that occurred in China in 2008 caused severe damage to a large number of electric substations. In this paper, Kriging interpolation method was used to calculate the impact area of the instrumental seismic intensity in Wenchuan earthquake, and to compare the intensities based on strong motion observation against the instrumental seismic intensities at locations where the observation data is available. The instrumental seismic intensities were calculated for the Wenchuan Earthquake at substations in the national power grid with voltage of 110kV or higher in areas of Mianyang, Deyang, Guangyuan and Chengdu. The cumulative Gaussian distribution function was then used to fit the relationship of the curves of the damage probabilities of high-voltage electrical equipment such as transformers, voltage mutual inductors, current mutual inductors, circuit breakers, isolating switches and lightning arrester with their instrumental seismic intensities. The damage probability density distribution curve of high-voltage electrical equipment based on the instrumental seismic intensities was obtained. The results showed that: (1) In the lower seismic intensity region, the mean instrumental seismic intensity was in good agreement with the traditional seismic intensity, but there was noticeable dispersion; in regions of intensity IX and above, the instrumental intensity was lower than the seismic intensity, but there was a lower degree of dispersion. (2) Among high-voltage electrical equipment, the transformers were most vulnerable to damage and they had some damage even under lower instrumental intensity. More damage would be produced when the instrumental intensity reached VIII or above; the second most vulnerable equipment was the circuit breaker, and the damage was most likely to occur when the instrument intensity was IX or above . (3) The damage rate curves of lightning arresters, current mutual inductors, voltage mutual inductors and isolating switches were relatively close to each other and the damage probability was the highest when the instrumental intensity was about X.

Wenchuan earthquake that occurred in China in 2008 caused severe damage to a large number of electric substations. In this paper, Kriging interpolation method was used to calculate the impact area of the instrumental seismic intensity in Wenchuan earthquake, and to compare the intensities based on strong motion observation against the instrumental seismic intensities at locations where the observation data is available. The instrumental seismic intensities were calculated for the Wenchuan Earthquake at substations in the national power grid with voltage of 110kV or higher in areas of Mianyang, Deyang, Guangyuan and Chengdu. The cumulative Gaussian distribution function was then used to fit the relationship of the curves of the damage probabilities of high-voltage electrical equipment such as transformers, voltage mutual inductors, current mutual inductors, circuit breakers, isolating switches and lightning arrester with their instrumental seismic intensities. The damage probability density distribution curve of high-voltage electrical equipment based on the instrumental seismic intensities was obtained. The results showed that: (1) In the lower seismic intensity region, the mean instrumental seismic intensity was in good agreement with the traditional seismic intensity, but there was noticeable dispersion; in regions of intensity IX and above, the instrumental intensity was lower than the seismic intensity, but there was a lower degree of dispersion. (2) Among high-voltage electrical equipment, the transformers were most vulnerable to damage and they had some damage even under lower instrumental intensity. More damage would be produced when the instrumental intensity reached VIII or above; the second most vulnerable equipment was the circuit breaker, and the damage was most likely to occur when the instrument intensity was IX or above . (3) The damage rate curves of lightning arresters, current mutual inductors, voltage mutual inductors and isolating switches were relatively close to each other and the damage probability was the highest when the instrumental intensity was about X.

The objective of this paper is to research the impact of electrical and physical parameters that characterize the complementary MOSFET transistors (NMOS and PMOS transistors) in the CMOS inverter for static mode of operation. In addition to this, the paper also aims at exploring the directives that are to be followed during the design phase of the CMOS inverters that enable designers to design the CMOS inverters with the best possible performance, depending on operation conditions. The CMOS inverter designed with the best possible features also enables the designing of the CMOS logic circuits with the best possible performance, according to the operation conditions and designers’ requirements.

In this work, we study a Klein-Gordon oscillator subject to Cornelltype potential in the background of the Lorentz symmetry violation determined by a tensor out of the Standard Model Extension. We introduce a Cornell-type potential S(r) = (η_L\,r + \frac{η_c}{r} ) by modifying the mass term via transformation $M → M + S(r)$ and then coupled oscillator with scalar particle by replacing the momentum operator $\vec{p}→ (\vec{p}+ i\,M\,ω\,\vec{r})$ in the relativistic wave equation. We see that the analytical solution to the Klein-Gordon oscillator equation can be achieved, and a quantum effect characterized by the dependence of the angular frequency of the oscillator on the quantum numbers of the relativistic system is observed

In this research paper, a novel high step up dc-dc converter with a coupled inductor and voltage doubler circuits is proposed. The converter achieves a high step up voltage gain with an appropriate duty ratio and low voltage stress on the power switches. Also, the energy which is stored in the leakage inductor of the coupled inductor can be recycled to the output. The operating principles and the steady state analysis of the proposed converter are discussed in detail. Finally, a prototype circuit of the proposed converter is implemented in the laboratory in order to verify the performance of the proposed converter.

This paper considers the principles of building a circuit model of film resistor cutting. The conductive resistive medium is defined with the component equations and the topology of the circuit model. A method of estimating the electric parameters of a resistor operating in the system with a measuring voltage source is shown. An equation system for the node voltages is defined, and the resistive layer parameters are analyzed as the circuit model structure changes during the cutting process.

With the widespread application of Voltage Source Converter (VSC) in the power system with high penetration of renewable resources, the problem of wideband oscillations caused by the interaction between the power converters and the power grid has drawn large attention. This paper presents a new methodology for simplifying the mathematical derivations of the impedance model of VSC. Using the new simplified model, the stability and the spectrum characteristic of the performance of the VSC can be clearly analyzed. The proposed second-order d-q impedance model of the grid connected VSC at presence of PLL, not only mathematically proves that the wideband oscillatory modes always occurs in conjugate pairs, but also deliver a clear vision of the physical essence of the wideband oscillations. The classic modal analysis is executed in the paper to demonstrate the stability and frequency spectral characteristics of the wideband oscillations in the VSC integrated system. The impact of control parameters of the VSC on the wideband oscillatory stability is thouroughly analyzed using the results of the modal analysis. The methodology can be considered a powerful tool for the control design of VSC in the modern power system.

This article delves into the complex landscape of Bitcoin halving events, analyzing the historical context and implications of these pivotal occurrences within the cryptocurrency ecosystem and on its sustainability within the landscape of financial technologies. Through an examination of past halving events in 2012, 2016, and 2020, this study meticulously scrutinizes the conditions and prices of Bitcoin before and after each halving. By synthesizing data and trends from previous events, this article aims to uncover patterns and insights that illuminate the impact of Bitcoin halving on market dynamics and sustainability, movement of the price level, reached peaks and price troughs. Furthermore, this research presents a comparative analysis of past halving events, drawing parallels and distinctions to elucidate the evolving nature of Bitcoin's price movements and market sentiment surrounding these milestone events. Looking towards the future, this study estimates predictions and expectations for the upcoming Bitcoin halving. By unraveling the intricate relationship between Bitcoin halving events and market behavior, this article seeks to provide a comprehensive understanding of the broader implications for Bitcoin's trajectory and the evolving landscape of the cryptocurrency market and its sustainability.

Pathogens that adapt to environmental stress can develop an increased tolerance to some physical or chemical antimicrobial treatments. The main objective of this study was to determine if acid adaptation increased the tolerance of Escherichia coli O157:H7 to high voltage atmospheric cold plasma (HVACP) in raw pineapple juice. Samples (10 ml) of juice were inoculated with non-acid-adapted (NAA) or acid adapted (AA) E. coli to obtain a viable count of ~ 7.00 log10 CFU/ml. The samples were exposed to HVACP (70 kV) for 1 to 7 min with inoculated non-HVACP-treated juice serving as control. Juice samples were analyzed for survivors at 0.1 h, and after 24 h of refrigeration (4 °C). Samples analyzed after 24 h exhibited significant decreases in viable NAA cells with sub-lethal injury detected in both NAA and AA survivors (P&lt;0.05). No NAA survivor in juice exposed to HVACP for 5 or 7 min was detected after 24h. However, numbers of AA survivors were 3.33 and 3.09 log10 CFU/ml in juice treated for 5 and 7 min, respectively (P&lt;0.05). These results indicate that acid adaptation increases the tolerance of E. coli to HVACP in pineapple juice. The potentially higher tolerance of AA E. coli O157:H7 to HVACP should be considered in developing safe juice processing parameters for this novel non-thermal technology.

To realize precise control of single quantum dots (Qdots) device, the high-performance bias source play the key role. In this paper, the 16-channel high precision voltage bias source prototype for Qdots device with 18-bit resolution was designed. The prototype was made and its performance was tested. The short time fluctuations can reach 50μV. The up-step and the down-step response time can achieve less than 3μs. The stability, linearity and setting time of the bias source exhibits good performance. What's more, the voltage bias source can be controlled by local and online. The results show that it is one effective and feasible topology for the high precision voltage bias source in Qdots device application.

An adaptive operation strategy for on-demand control of DMFC system is proposed as an alternative method to enhance the voltage stability. Based on a single-cell DMFC stack, a newly simplified semi-empirical model is developed from the uniform-designed experimental results to describe the I-V relationship. Integrated with this model, the multi-objective optimization method is utilized to develop an adaptive operation strategy. Although the voltage instability is frequently encountered in unoptimized operations, the voltage deviation is successfully decreased to a required level by adaptive operations with operational adjustments. Moreover, the adaptive operations are also found to be able to extend the range of operating current density or to decrease the voltage deviation according to ones requirements. Numerical simulations are implemented to investigate the underlying mechanisms of the proposed adaptive operation strategy, and experimental adaptive operations are also performed on another DMFC system to validate the adaptive operation strategy. Preliminary experimental study shows a rapid response of DMFC system to the operational adjustment, which further validates the effectiveness and feasibility of the adaptive operation strategy in practical applications. The proposed strategy contributes to a guideline for the better control of output voltage from operating DMFC systems.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

Tefluthrin (Tef) is categorized as a type-I pyrethroid insecticide, telmisartan (Tel) functions as an angiotensin II receptor blocker, and KB-R7943 was identified as an inhibitor of Na+-Ca2+ exchange process. However, the influence of these compounds on the amplitude and gating properties of voltage-gated Na+ current (INa) in neurons associated with pain signaling remains unclear. In cultured dorsal root ganglion (DRG) neurons, whole-cell current recordings revealed that Tef or Tel increased the peak amplitude of INa, concomitant with an elevation in the time constant of INa inactivation, particularly in the slow component. Conversely, exposure to KB-R7943 resulted in a depression in INa, coupled with a decrease in the slow component of the inactivation time constant of INa. Theoretical simulations and bifurcation analyses were performed on a modeled interneuron in the spinal dorsal horn. The occurrence of INa inactivation accentuated the subthreshold oscillations (SO) in the membrane potential. With an increase in applied current, SO became more pronounced, accompanied by the emergence of high-frequency spiking (HF) with a frequency of approximately 150 Hz. Moreover, an elevation in INa conductance further intensified both SO and HF. Consequently, through experimental and in silico studies, this work reflects that Tef, Tel, or KB-R7943 significantly impacts the magnitude and gating properties of INa in neurons associated with pain signaling. The alterations in INa magnitude and gating in these neurons suggest a close relationship with pain transmission.

This study utilized electron back scattered diffraction (EBSD) and X-ray diffraction (XRD) to investigate the impact of inter-annealing temperature and heating rate of final annealing on the microstructure of high-voltage anode aluminum foils. The findings indicate that the formation of cube texture in the final products is significantly influenced by the inter-annealing temperature, as low inter-annealing temperatures retain a considerable amount of deformation stored energy, providing a strong driving force for nucleation. The cube texture is observed to deviate from the ideal position at lower inter-annealing temperatures. Additionally, an increase in heating rate during final annealing leads to a gradual decrease in the fraction and grain size of recrystallization. This is attributed to the fact that a higher heating rate (below the critical heating rate) reduces the time available for grain boundary migration, thereby slowing the recrystallization process.

Lead-free ferroelectric perovskite N-methyl-N'-diazabicyclo[2.2.2]octonium)–ammonium triio-dide, MDABCO-NH₄I₃, nanocrystals are embedded in three different polymer fibers fabricated by the electrospinning technique. The nanofibers, which are very flexible and have a high Young modulus, behave as active piezoelectric energy harvesting sources that produce a piezoelectric voltage coefficient up to geff = 3.6 VmN-1 and show a blue intense luminescence band at 325 nm. In this work, the pyroelectric coefficient is reported for the MDABCO-NH₄I₃ perovskite inserted in electrospun fibers. At the ferroelectric-paraelectric phase transition, the embedded nanocrystals display a pyroelectric coefficient as high as 194×10-6 Cm-2k-1, within the same order of magnitude as that reported for the state-of-the-art bulk ferroelectric triglycine sulfate (TGS). The perovskite nanocrystals embedded into the polymer fibers remain stable, and no degradation is caused by oxidation.

The increasing expansion of the use of renewable distributed generation (RDG) technologies in electrical networks such as solar plants or wind farms and others has changed the nature of the distributed system and transformed it from the traditional system into an efficient system. This system has led to various technical effects in the host networks, with regard to voltage, electrical energy losses, fault levels, stability and electrical energy quality. These effects are not generic to any network; It can be positive, negative or neutral depending on the structure of the studied network, its operational condition and the various technology of the distributed generators. This research aims to quantitatively correct the effects of (RDG) in terms of voltage and electrical energy losses in the host networks. , since efficient distribution systems contain generators of a special nature and often contain bidirectional flux energy, it was necessary to construct a mathematical model of the distribution system hosting RDG units, which is fundamentally different from the traditional model of defining the reference electrical distribution bus bar. In order to achieve the systematic analysis, evaluation criteria and indicators were determined and mathematical formulas for them were completed. Based on the accomplished mathematical basis, an algorithm designed in such a way that it can be applied to any multi-voltage distribution system and to different distributed regenerative generation techniques is proposed. To demonstrate the algorithm's capabilities, it was tested on typical distribution networks using Factory Power DigSilent software, which is somewhat similar to MATLAB but more suitable for large capacity systems.

Superior fiber quality is one of the most important objectives in cotton breeding. To detect the genetic basis underlying fiber quality, an F2 population containing 413 plants was constructed by crossing Jifeng 914 and Jifeng 173, both of which have superior fiber quality, with Jifeng 173 being better. Five fiber quality traits were investigated in the F2, F2:3, F2:4, and F2:5 populations. Quantitative trait loci (QTL) mapping was conducted based on a high-density genetic map containing 11,488 single nucleotide polymorphisms (SNPs) and spanning 4,202.12 cM in length. Transgressive segregation patterns and complex correlations in the five tested traits were observed. A total of 108 QTLs were found, including 27 for fiber length (FL), 16 for fiber strength (FS), 24 for micronaire (MC), 17 for fiber uniformity (FU), and 24 for fiber elongation rate (FE). Chromosome A7 contained 12 QTL, ranking the first. No QTL was found on chromosome D1 and D11. Each QTL contributed 1.98%–21.45% to the phenotypic variation (PV), including 13 major effect QTLs that contributed more than 10% toward PV. Two QTLs could be repeatedly detected in three populations, including qFL-D3-2 in F2, F2:4, and F2:5 with 9.18%–21.45% of PV, qFS-A11-1 in F2:3, F2:4 and F2:5 with 6.05%–10.41% of PV. Another seven stable QTLs could be detected in two populations, including four major effect QTLs: qFL-A12-3, qFS-D10-2, qMC-D6-2, and qMC-D8-1. Fourteen QTL-overlapping regions were found, which might explain the complex correlations among the five phenotypic traits. Four regions on chromosome A11, D3, D6, and D10 covered by both stable and major effect QTLs are promising for further fine mapping. The genomic regions of the two QTLs detected in three populations and the four major effect QTLs contain 810 genes. Gene functional analysis revealed that the annotated genes are mainly involved in protein binding and metabolic pathways. Fifteen candidate genes in the qFL-D3-2 region are highly expressed in fiber or ovules during fiber initiation, elongation, secondary cell wall thickening, or maturation stages. qRT-PCR revealed that Ghir_D03G005440.1 and Ghir_D03G011310.1 may play a role in promoting fiber initiation, Ghir_D03G006470.1 may be beneficial for promoting fiber elongation. This study provides more information for revealing the molecular genetic basis underlying cotton fiber quality.

In recent years, electroencephalogram (EEG) emotion recognition has emerged as a research hotspot in the field of artificial intelligence (AI). Despite advancements in EEG-based emotion recognition, room for enhancing performance persists due to EEG signal redundancy and limitations in feature extraction, leading to inefficient models and emotional information loss. To fully utilize EEG's emotional information and improve recognition accuracy while reducing computational costs, this paper proposes a Convolutional-Recurrent Hybrid Network with a dual-stream adaptive approach and an attention mechanism (CSA-SA-CRTNN). Firstly, the model utilizes a CSAM module to assign corresponding weights to EEG channels. Then, an adaptive dual-stream convolutional-recurrent network (SA-CRNN and MHSA-CRNN) is applied to extract local spatial-temporal features. After that, the extracted local features are concatenated and fed into a temporal convolutional network with a multi-head self-attention mechanism (MHSA-TCN) to capture global information. Finally, the extracted EEG information is used for emotion classification. We conducted binary and ternary classification experiments on the DEAP dataset, achieving 99.26% and 99.15% accuracy for arousal and valence in binary classification, and 97.69% and 98.05% in ternary classification, surpassing relevant algorithms. Additionally, the model's efficiency is significantly higher than other models, achieving better accuracy with lower resource consumption.