Titanium-based metal-matrix composites manufactured by additive manufacturing offer tremendous lightweighting opportunities. However, processing high reinforcement content remains challenging. This study reports an improved manufacturing process for Ti-TiC enabling high reinforcement content and significant fracture strain concurrently: mechanical blending, followed by laser powder bed fusion and a single heat treatment. As-built microstructure shows both un-melted TiC particles and sub-stoichiometric TiC dendrites resulting from a partial dissolution of TiC particles. The heat treatment is shown to fully convert TiC dendrites into equiaxed TiC grains. Reduction of the C/Ti ratio in TiC during the process results in an increase in the reinforcement content, from a nominal 12 vol% to an effective 21.5 vol%. Ti-TiC tensile samples reached fracture strains of up to 1.7%, Young’s moduli of up to 149 GPa and ultimate tensile strengths of up to 827 MPa. Lower TiC initial powder size distributions displayed the best mechanical performance.

This study outlines a 3-step production process for Ti-TiC Metal Matrix Composite (MMC) employing powder Mechanical Blending, Laser Powder Bed Fusion (LPBF), and a heat treatment. A TiC fraction of more than 20 vol% was formed in-situ through the reaction of titanium with carbon during the LPBF process. The manufactured MMC pieces showed a record stiffness and fracture strain combination. The LPBF energy density impacted strongly porosity type. The as-built microstructure displayed an homogeneous distribution of sub-stoichiometric TiC dendrites which were fully converted into equiaxed TiC grains during the heat treatment. The TiC C/Ti ratio was found to be close to 0.5, resulting in an effective reinforcement content nearly twice the one expected for stoichiometric TiC, leading to stronger reinforcement. The mechanical analysis revealed a Young’s modulus of up to 149 GPa and an ultimate tensile strength of up to 770 MPa, indicating a 27% and 34% improvement, respectively, compared to commercially pure Titanium produced by LPBF and heat treated in the same conditions. A fracture strain of up to 2.8% was achieved. The combination of in-situ formation of defect-free TiC reinforcement and subsequent heat treatment enables to reach an exceptional ductility, considering the 20 vol% reinforcement content.

Previous research has indicated that ultra-high pressure (UHP) technology is useful in speeding up the extraction process of cold brew (CB) coffee. However, the impact of different degrees of roasting on UHP CB coffee is still unclear. Therefore, this study aimed to investigate the effects of three different degrees of roasting (light, medium, and dark) on the physicochemical and flavor characteristics of UHP CB coffee. The results of this study showed that most physicochemical characteristics of UHP coffee were similar to those of conventional CB coffee, regardless of the degree of roasting. However, the majority of physicochemical characteristics, non-volatile components, and sensory evaluation significantly increased with an increase in roasting degree. The HS-SPME-GC/MS analysis showed that most volatile components, such as pyrazines, furans (except furfural), esters, pyrrole, pyridine, and most aldehydes, increased from light to dark roasting, and this was significantly evident in CB coffee compared with UHP. The content of volatile components in UHP coffee was significantly (P<0.05) higher than that in CB coffee at the same degree of roasting, especially with dark roasting. The combination of orthogonal partial least squares-discriminant analysis (OPLS-DA) and principal component analysis (PCA) indicated that the distance between coffee samples at different degrees of roasting under CB coffee was greater than that under UHP coffee. However, the distance between these two extraction methods at medium roasting was evidently closer than that at light and dark roasting. Moreover, 15 representative differential compounds, such as were Hazelnut pyrazine, linalool, butane-2,3-dione, 3- methylbutanal found by the calculation of odor-active values (OAVs) indicating the main contributing compounds to odor. Overall, the effect of roasting degrees on UHP coffee was less than that on CB coffee, which was consistent with the results of physicochemical characteristics, volatile components, and sensory evaluation.

Nowadays, the identification and characterization of grapevine cultivars resilient to climate and water stress while preserving quality traits is crucial for the wine industry. Therefore, the objective of this work was to characterize according to their aromatic potential 9 white and 6 red minority cultivars recently recovered from Castilla-La Mancha region (Spain), subjected at two different water deficit regimes: rainfed, with subsistence irrigation, and irrigated. For this, the varietal aromatic potential index (IPAv) and the detailed aromatic composition were analyzed by HS-SBSE-GC/MS, in extracts of two different ph. For IPAv values, red varieties did not show a clear trend with respect to irrigation. However, in white minority varieties, higher values were obtained under irrigation conditions. Thus, a clear differentiation of the minority varieties in comparison to the references was observed, primarily attributed to the content of esters and acids, in both white and red varieties. A notable contrast was observed at different pH, indicating a greater extractability of certain compounds like linalool, under more acidic conditions. This suggests that some recovered minority cultivars could be promising for cultivation in semi-arid regions with limited water, contributing to the wine sector sustainability in the future.

Researchers are exploring solutions to meet the growing demand for protein due to the expected increase in global population by 2050. Interest in alternative protein sources like insects has risen, driven by concerns about environmental impact and the need for sustainable food production. This study aimed to develop and evaluate the physicochemical properties of soy protein-based burger enriched with insect protein from Alphitobius diaperinus. Three formulations were developed: a control (B0), and burgers with 5% (B5) and 10% (B10) insect protein - Whole Buffalo Powder (WBP). Results showed that adding insect protein decreased the burger analogue's pH. There was observed a clear trend of increasing total lipids and SFA, and decreasing MUFA and PUFA, as the WBP concentration increases from 0% to 10%. No significant differences with increasing WBP concentration in the protein content of the burger analogue, as well as the cooking yield, were noted. The WBP addition had a notable effect on the color change, especially decrease in brightness (L*). It was shown that as the WBP concentration increased, there were no significant differences in the texture profile of the burger analogues. The formulation with 5% WBP concentration was the most acceptable in sensory analysis.

Vanilla planifolia is grown as a high-value orchid spice for its odor and savor attributes that increase due to the curing process associated with microbial colonization. This tends to influence the aromatic properties of vanilla. Hence, 11 Bacillus sp. strains were isolated from V. planifolia and identified with 16S rRNA gene sequencing. The liquid culture (1 mL of 107 CFU mL-1) of selected Bacillus vallismortis NR_104873.1:11-1518, B. velezensis ZN-S10, and B. tropicus KhEp-2 effectively fermented green-blanched vanilla pods kept at 10 ℃ during the sweating stage. GC-MS analysis showed that the methanol extract of non-coated, and B. vallismortis treated vanilla detected three (3) volatile compounds, whereas seven (7) components were obtained in B. tropicus and B. velezensis treatment. 4H-pyran-4-one, 2,3-dihydro-3,5-dihydroxy-6-methyl was found in B. velezensis ZN-S10, B. tropicus KhEp-2, B. vallismortis while it was not present in the control samples. This ketone compound suggested a Maillard reaction resulting in brown-increased aroma pods. Linoleic acid and Hexadecanoic acid ethyl esters were detected only in ZN-S10 strain-coated vanilla. A novel 3--Deoxy-d-mannoic lactone was detected only in B. vallismortis treated vanilla characterized as a new compound in V. planifolia which suggested that the new compound can be altered with the coating of bacteria in vanilla during fermentation. Thus, the Bacillus strains improved the volatile profile and exhibited a new aroma and flavor profile of vanilla owing to bacteria fermentation during the curing process.

For this research we are selected three indicators of wheat: yield (t/ha), producer price (USD/t) and share of the harvested area under wheat in relation to the total land area of country (%). The mentioned indicators were analyzed for the period 2006-2021 in thirty-two European countries. The purpose of the research is to determine which of the mentioned indicators achieve average annual growth/decrease rates, what is the correlation between them, how European countries are grouped with their similarities and differences. The research examines the impact of the COVID-19 pandemic on the mentioned indicators in a two time phases: Phase I, before the pandemic (2006-2019); Phase II, during the pandemic (2020-2021). The methodological approach to the research topic involved the application of descriptive statistics, as the method of principal components analysis (abbr. PCA) with graphics. A positive correlation exists only between the yield of wheat and the share of the harvested area under wheat in the total area of the land (0.291). PCA method showed that countries are grouped differently depending on the observed indicator and the analyzed time phase.

The software industry has adopted component-based software development (CBSD) to rapidly build and deploy large and complex software systems with significant savings at minimal engineering effort, cost, and time. However, CBSD encounters issues on security trust, mainly with respect to dependability attributes. A system is considered dependable when it can produce the outputs for which it was designed with no adverse effect on its intended environment. Dependability consists of several attributes that imply availability, confidentiality, integrity, reliability, safety, and maintainability. Dependability attributes must be embedded in a CBSD model to develop dependable component software. Motivated by the importance of these attributes, this paper pursues two objectives: to design a model for developing a dependable system that mitigates the vulnerabilities of software components, and to evaluate the proposed model. The model proposed in this study is labelled as developing dependable component-based software (2DCBS). To develop this model, the CBSD architectural phases and processes must be framed and the six dependability attributes embedded according to the best practice method. The expert opinion approach was applied to evaluate 2DCBS framing. In addition, the 2DCBS model was applied to the development of an information communication technology (ICT) portal through an empirical study method. Vulnerability assessment tools (VATs) were employed to verify the dependability attributes of the developed ICT portal. Results show that the 2DCBS model can be adopted to develop web application systems and to mitigate the vulnerabilities of the developed systems. This study contributes to CBSD and facilitates the specification and evaluation of dependability attributes throughout model development. Furthermore, the reliability of the dependable model can increase confidence in the use of CBSD for industries.

The HS-SPME GC-MS analysis of the volatile compounds adsorbed at the outer surface of lemon and grapefruit pectins obtained via hydrodynamic cavitation of industrial waste streams of lemon and grapefruit peels in water only suggests important new findings en route to understanding the powerful and broad biological activity of these new pectic materials. In agreement with the ultralow degree of esterification of these pectins, the high amount of highly bioactive α-terpineol and terpinen-4-ol points to limonene decomposition catalyzed by residual citric acid in the citrus waste peel residue of the juice industrial production.

Sensory descriptive analysis was used to evaluate the aged Feng-flavored baijiu. The results indicated that there are notable differences in the samples of different ages. The samples with shorter storage times and fresh distilled Baijiu present bran flavor, and fresh green flavor. with the increase of storage time, the fragrance of honey, sweetness, flowers, and aging gradually increases. The samples of Feng-flavored baijiu were dected by Headspace solid-phase microextraction (HS-SPME) combined with comprehensive two-dimensional gas chromatography time-of-flight mass spectrometry (GC×GC–TOFMS) , in total, 496 sustances were identified in all samples, mainly containing 14 types of substances, such as esters, aldehydes etc., of which 42 substances were found in Feng-flavored baijiu for the first time. Chemometrics was used to analyze the key differential compounds. 143 differential compounds closely related to aging were preliminarily screened, and principal component analysis revealed that these samples were separated by year. 65 differential compounds were selected out by partial least squares discriminant analysis(PLS-DA). Furthermore, 43 key differential compounds were selected from the aged Feng-flavored baijiu combined with variable importance in projection and Pearson correlation coefficients. Partial least squares regression (PLSR) was used to research the correlation of sensory properties and key differential compounds, and the results indicated that most compounds were closely related to the aged Baijiu . This study afford theoretical basis and reference for flavor research of Feng-flavored baijiu.

The present study comprises the second part of our previous work that dealt mainly with the phytochemical and physicochemical characterization of green coffee, clove, cinnamon/clove and nutmeg ethanolic extracts of grape origin. In the present study, we focused on producing a discriminating model concerning green coffee, clove, cinnamon, cinnamon and clove, and nutmeg fine powders based on multivariate analysis of variance and supervised learning on data of volatile compounds analysis, carried out with solid phase dynamic extraction in combination with gas chromatography/mass spectrometry. Results showed that 7 volatile compounds namely ethylene, methanol, 3-methylpentane, ethyl acetate, 9-hexadecen-1-ol, toluene, and methyl acetate could differentiate the investigated samples resulting in a 100% classification rate using the cross-validation method of linear discriminant analysis. Results were further confirmed using partial least squares regression analysis. The study contributes to the typification of green coffee, cinnamon, clove, cinnamon and clove and nutmeg, based on selected volatile compounds, and provides further support to the literature by means of possible adulteration given the statistical models developed.

In recent years, long periods of drought and heat waves have become increasingly frequent, causing forest dieback phenomena that make stands more sensitive to biotic stressors. How trees may respond to extreme climatic events and which metabolites are involved under stress conditions is still not clear. In this study, we analysed by SPME how dieback (D) and non-dieback (ND) Hungarian oak trees from the San Paolo Albanese site respond to these climatic dynamics, in terms of volatile organic compounds (VOCs). For each group of trees, three wood samples were taken, each divided into four sub-samples with 5 growth rings, subjected to SPME and increase in basal area (BAI) analysis of the last 20 years. Dieback trees had a lower amount of leaves, and this condition may translate into less photosynthesis, less organic matter production and lower reserves of carbohydrates available for growth. Indeed, D trees showed lower radial increases and a lower content of aldehydes, terpenes, and fatty acids than ND trees, indicating a better health of ND trees compared to D trees. While D trees showed a reduction in terpenes, such as α-pinene, γ-eudesmol, and cyperene (with significant insecticidal activity), a reduction in aromatic aldehydes, such as furfural and 5-methylfurfural, and an increase in silanols (with antimicrobial function). Considering the different compounds’ contents between D and ND trees, our study could be useful for detecting bio-indicators to identify an early warning signal of dieback phenomena.

Tackling the intricacies of network dismantling in complex systems poses significant challenges. This task has relevance across various practical domains, yet traditional approaches focus primarily on singular metrics, such as the number of nodes in the Giant Connected Component (GCC) or average pairwise connectivity. In contrast, we propose a unique metric that concurrently targets nodes with the highest degree and reduces the GCC size. Given the NP-hard nature of optimizing this metric, we introduce MaxShot, an innovative end-to-end solution that leverages graph representation learning and reinforcement learning. Through comprehensive evaluations on both synthetic and real-world datasets, our method consistently outperforms leading benchmarks in accuracy and efficiency. These results highlight MaxShot’s potential as a superior approach to address the network dismantling problem effectively.

Despite soccer popularity, comparatively little scientific information is available concerning the assessment of youth players’ physiological characteristics. The use of medical software integrating wearable sensors to provide accurate and objective data is necessary. In the present study, the objective assessment of physical performance of 128 adolescent soccer players at two timepoints (pre-season and end-season) has been performed. Participants completed a comprehensive test battery including stability, countermovement jumps (CMJ), plyometric jumps (PJ), agility, and quick feet tests. A single Inertial Measurement Unit (IMU) sensor provided quantitative data on various performance metrics. Principal Component Analysis (PCA) reduced the dataset to four principal components (PCs) explaining over 80% of the variance: power (PC1), balance (PC2), speed/agility (PC3), and stiffness (PC4). Paired samples t-test between the two timepoints showed no significant differences in the PCs between the two timepoints, indicating that the training program did not significantly alter the assessed physical attributes. However, subtle individual changes may still inform personalized training adjustments. The study highlights the importance of continuous monitoring and individualized training strategies to optimize athlete performance and reduce injury risk.

This paper presents an upcoming nonvolatile memories (NVM) overview. Non-volatile memory devices are electrically programmable and erasable to store charge in a location within the device and to retain that charge when voltage supply from the device is disconnected. The non-volatile memory is typically a semiconductor memory comprising thousands of individual transistors configured on a substrate to form a matrix of rows and columns of memory cells. Non-volatile memories are used in digital computing devices for the storage of data. In this paper we have given introduction including a brief survey on upcoming NVM's such as FeRAM, MRAM, CBRAM, PRAM, SONOS, RRAM, Racetrack memory and NRAM. In future Non-volatile memory may eliminate the need for comparatively slow forms of secondary storage systems, which include hard disks.

One of the most concerning global environmental issues is the pollution of agricultural soils by heavy metals (HMs), especially cadmium (Cd), which not only affects human health by taking Cd-containing foods but also impacts the quality of rice. The soil's nitrification and denitrification processes, coupled with the release of volatile organic compounds by plants, raise substantial concerns. The understanding of three aspects of paddy soil under conditions of heavy-metal pollution and water management is currently limited. In this review, we summarized recent literature related to the deleterious effects of Cd on both soil processes related to the N cycle and rice quality, particularly aroma, in different water management practices. Under both continuous flooding (CF) and alternate wetting and drying (AWD) conditions, cadmium (Cd) has been observed to reduce both nitrification and denitrification processes. The adverse effects are more pronounced in continuous flooding (CF) compared to alternate wetting and drying (AWD). Similarly, the alteration in rice aroma is more significant in AWD than in CF. The precise modulation of volatile organic compounds (VOCs) by Cd, remains unclear based on the available literature. Nevertheless, HM accumulation is higher in AWD conditions compared to CF, leading to a detrimental impact on volatile organic compounds (VOCs). The literature concluded that AWD practices should be avoided in Cd contaminated fields to decrease accumulation and maintain the quality of rice. In the future, rhizospheric engineering and plant biotechnology can be used to decrease the transport of HMs from the soil to the plant’s edible parts.

Principal Component Analysis (PCA) is a method that identifies common directions within multivariate data and presents the data in as few dimensions as possible. One of the advantages of PCA is its objectivity, as the same results can be obtained regardless of who performs the analysis. However, PCA is not a robust method and is sensitive to noise. Consequently, the directions identified by PCA may deviate slightly. If we can teach PCA to account for this deviation and correct it, the results should become more comprehensible. The methods for doing this and an issue with this are presented.

While some research supports utilizing plain radiography for measuring biomechanical alignment of the spine for prognosis and treatment, there are contrasting viewpoints regarding both the value and utilization of these procedures in conservative care. Evaluation of both conservative and non-conservative approaches to spinal care revealed vast differences in radiographic utilization and interpretation between orthopedic surgeons, primary care physicians, chiropractic physicians, and physical therapists, which may account for the different viewpoints and rationale in the literature. A research summary is provided regarding the various methods of spinal analysis utilized by these professions to help determine if there is any unique diagnostic or prognostic value associated with radiographic utilization that could assist in advancing conservative spinal assessment and treatment. Understanding any unique value provided through biomechanical assessment utilizing plain radiography of the spine established in the literature may help chiropractic physicians determine the appropriate use of radiographic procedures in clinical practice and how to coordinate efforts with other conservative and non-conservative professions to improve spinal healthcare.

Due to its application as an anti-cancer drug, pazopanib (1) has attracted the interest of many researchers and several studies on pazopanib synthesis have been reported over the years. This paper provides a novel route for synthesizing N,2,3-trimethyl-2H-indazol-6-amine (5) which is a crucial building block in the synthesis of pazopanib from 3-methyl-6-nitro-1H-indazole (6). By alternating between the reduction and two methylation steps compound 5 was obtained in comparable yield (55.0%) to what has been reported (54%). Noteworthy, the last step of N2-methylation also yielded N,N,2,3-tetramethyl-2H-indazol-6-amine (5’) as a new compound ever reported. Furthermore, the data presented in this paper can serve as instrumental for future research aimed at further refining the synthesis process of pazopanib.

Forest healing effects are increasingly valued for their contribution to human psychological and physiological health, motivating further advances aimed at improving the knowledge of the relevant forest resources. Biogenic volatile organic compounds, emitted by the plants and accumulating in the forest atmosphere, are essential contributors to the forest healing effects, and represent the focus of this study. Using a photoionization detector, we investigated the high frequency variability, in time and space, of the concentration of total volatile organic compounds, on a hilly site, as well as along forest paths and long hiking trails on Italian northern Apennines. The scale of concentration variability was found to be comparable to absolute concentration levels, within time scales of less than one hour, and spatial scales of several hundred meters. During daylight hours, the concentration peaked from noon to early afternoon, followed by early morning, with lowest levels in late afternoon. Based on a conceptual model, these results were related to meteorological variables, including the atmospheric vertical stability profile. Moreover, preliminary evidence pointed to higher concentration of volatile organic compounds in forests dominated by conifer trees, in comparison with pure beech forests.

Abstract: Recent years demonstrate the increased attention to radon from two scientific directions. After neglecting radon as earthquake precursors in 1990-th it becomes again the subject of earthquake-forecast papers discussions due to growing networks of the radon monitoring in different countries, especially, the technologies of real-time radon measurements where the gamma-spectrometers become the leader of interest as the sources of 222Rn identification. The second fast developing direction is including the radon in the Lithosphere-Atmosphere-Ionosphere Coupling (LAIC) models as a source of the boundary layer ionization. And here we encounter with second direction which is not connected with the earthquake forecast problems. It is the role of air ionization by radon as a source of the Global Electric Circuit (GEC) modification. In this publication we try to unite all these problems to present more complex view on radon as important element of our environment.

A monocular vision pose estimation and identification algorithm used on a small spacecraft for future orbital servicing is studied in this paper. A tracker spacecraft equipped with a short-range vision system is proposed to recover the 3D structural model of a space target in orbit and automatically identify its solar panels and main body using only visual information from an onboard camera. The proposed reconstruction and identification framework is tested using structure-from-motion and point cloud identification methods. The Efficient Perspective-n-Points (EPnP) descriptor is used for pose estimation. Triangulated points are used for component segmentation by means of orientation histogram descriptors. Experimental results based on laboratory images of a spacecraft model show the effectiveness and robustness of our approach.

Abrus precatorius is a medicinal herb originated from Southeast Asia and native to India. The Hindustani centre of origin was found to possess lot of variability especially with respect to seed color. However, no previous researchers have focused on studying the variability by including the entire variability of the region. A total of 99 accessions were analyzed for its biochemical components like moisture content, total phenols, antioxidants, ash content, protein content, total monomeric anthocyanin and flavonols. Principal component analysis (PCA) shown that first three components viz., seed color, phenols and antioxidants are major principal components that contribute to 80.86% of total variability in the germplasm. The dendrogram constructed based on the biochemical data and by using the software Darwin version 6.0. formed three main clusters i.e. cluster 1, cluster 2 and cluster 3 which contain 55 accessions, 40 accessions and 1 accession respectively. Seed color was found to be the main criteria based on which the Abrus accessions were grouped. Accessions from different clusters also differ for their mean phytochemical constituents. Germplasm curators / plant breeders can select such elite genotypes and utilize them in crop improvement programmes.

In large-scale parallel computing and communication systems, an interconnect network structure is usually modeled as a graph, in which vertices and edges correspond to processors and communication links, respectively. In a graph, the vertices and edges are likely to fail, so we must think about the fault tolerance of a graph. Connectivity is an important parameter in the study of faulty tolerance for a graph. In this paper, we study a special class of connectivity: $m$-component connectivity, this is a natural generalization of the classical connectivity of graphs defined in terms of the minimum vertex-cut. Let $F$ is a vertex set of $G$ $(i.e, F\subseteq V(G))$, if the following conditions are satisfied, we say $F$ is a $m$-component cut: $(1)$ $G-F$ is disconnected; $(2)$ the number of components in $G-F$ is greater than or equal to $m$. In another word, the $m$-component connectivity $c\kappa_{m}(G)$ is defined as $min\{|F|~|~F\subseteq V(G)$ and $F$ is a $m$-component cut$\}$. Determining $m$-component connectivity is still unsolved in most interconnection networks even for small $m'$s. Leaf-sort graph is a special Cayley graph, it has many special properties that are different from other Cayley graphs. So we need to pay attention to some of it's special properties when we study it. In this paper, we can get the values: $c\kappa_{3}(CF_{n})=3n-6$ $(n$ is odd$)$ and $c\kappa_{3}(CF_{n})=3n-7$ $(n$ is even$)$ for $n\geq3$; $c\kappa_{4}(CF_{n})=\frac{9n-21}{2}$ $(n$ is odd$)$ and $c\kappa_{4}(CF_{n})=\frac{9n-24}{2}$ $(n$ is even$)$ for $n\geq4$; $c\kappa_{5}(CF_{n})=6n-16$ $(n$ is odd$)$ and $c\kappa_{5}(CF_{n})=6n-18$ $(n$ is even$)$ for $n\geq5$.

The nuclear factor-ĸB (NF-ĸB) transcriptional system is a major effector pathway involved in inflammatory responses. Previous studies found that a Gardenia decoction (GD) inhibited the expression of NF-κB in a lipopolysaccharide (LPS)-stimulated mouse intestinal injury model. Herein, we hypothesized that geniposide (GE), a component of Gardenia jasminoides Ellis, also exerts anti-inflammatory effects and inhibits NF-ĸB activity in LPS-induced intestinal epithelial cells (IEC-6). IEC-6 cells were stimulated with LPS, following which the effects of GE on NF-ĸB signaling in the IEC-6 cells were examined by western blotting to detect IĸB phosphorylation/degradation. The expression of NF-κB was determined by immunofluorescence assay (IFA). Enzyme-linked immunosorbent assay (ELISA) was used to detect the inhibitory effect of GE on the release of tumor necrosis factor-α (TNF-α), interleukin-6 (IL-6) and interleukin-1β (IL-1β) activated by LPS in IEC-6 cells. In addition, the migration ability of IEC-6 cells was observed by the scratch method. These results showed that GE dose-dependently downregulated levels of the proinflammatory cytokines TNF-α, IL-6 and IL-1β that had been upregulated by LPS and suppressed the phosphorylation of IĸB and NF-ĸB induced by LPS. Our findings indicated that GE could reduce LPS-induced NF-ĸB signaling and proinflammatory expression in IEC-6 cells and significantly enhance the migration of IEC-6 cells. Moreover, GE inhibited the expression of NF-κB, nuclear transfer, and transcriptional activity in IEC-6 cells. GE could block the synthesis of inflammatory factors of IEC-6 cells by inhibiting activation of the IĸB/NF-κB signaling pathway induced by LPS.

Native and exotic fruits from the Amazon have varied characteristics, with aroma being a decisive factor in attracting and accepting them and their medicinal use as a nutraceutical supplement. This work aimed to analyze the chemical constituents of the volatile concentrates of some Myrtaceous fruit species sampled in the Brazilian Amazon. The fruit's pulps were subjected to simultaneous distillation-extraction, and gas chromatography-mass spectrometry was used to analyze their volatile chemical composition. In the volatile concentrate of Eugenia stipitata (Araçá-boi) were identified α-pinene (17.5%), citronellyl butanoate (15.6%), and pogostol (13.5%) as primary constituents; in Eugenia uniflora (Ginja) were curzerene (30.5%), germacrone (15.4%), atractylone (13.1%), and (E)-β-ocimene (11.1%); in Myrciaria dubia (Camu-Camu) were α-pinene (55.8%), (E)-β-ocimene (13.1%), and α-terpineol (10.0%); in Psidium guajava (Goiaba) were (2E)-hexenal (21.7%), hexanal (15.4%), caryophylla-4(12),8(13)-dien-5-β-ol (10.5%), caryophyllene oxide (9.2%), and pogostol (8.3%); and in Psidium guineense (Araçá) were limonene (25.2%), ethyl butanoate (12.1%), epi-β-bisabolol (9.8%), and α-pinene (9.2%). The analyzed fruit species' volatile concentrates presented a significant diversity of constituents with a predominance of functional groups, such as monoterpenes, sesquiterpenes, and fatty acid derivatives, originating from the plant's secondary metabolism and representing significant importance regarding their nutritional and medicinal uses.

Basil, renowned for its aromatic properties, exhibits commendable drought tolerance and holds significant value both as an edible and medicinal plant. Recognizing the scarcity of studies addressing basil’s response to drought stress, we undertook a comprehensive analysis of the volatile metabolome and transcriptome of sweet basil across four distinct levels of drought stress. Our metabolic analysis meticulously identified 830 metabolites, with 215 differentially accumulated metabolites discerned. Notably, the primary constituents of sweet basil volatiles exhibited minimal alterations, while the differentially accumulated metabolites were predominantly lipids and terpenes. The transcriptome analysis unveiled 27,181 differentially expressed DEGs, with a predominant focus on metabolic pathways and biosynthesis of secondary metabolites. Integrating insights from both transcriptome and volatile metabolomic analyses highlighted the pivotal roles of Alpha-linolenic acid, flavonoid, and lignin metabolism in fortifying the resistance of sweet basil against drought stress. This holistic approach not only enriches our understanding of the molecular intricacies underpinning basil’s drought resistance but also furnishes valuable insights for the molecular breeding of basil varieties endowed with enhanced drought tolerance.

The electronics industry is a significant contributor to environmental challenges, generating approximately 50 million tons of electronic waste annually and high levels of carbon dioxide emissions throughout the production and disposal of devices. This paper investigates the interplay between reliability and sustainability by analyzing how degraded components affect the environmental footprint of electronic products. Using a board with 215 components as a baseline, we calculate the mean time between failures (MTBF) and compare it to scenarios involving degraded components. Our findings demonstrate that degraded components can reduce MTBF by up to 50%, resulting in higher failure rates, increased electronic waste, and up to 30% more CO2 emissions due to shortened product lifespans. This study underscores the crucial importance of component quality control in the production process to improve both reliability and sustainability. Additionally, the broader economic and environmental impacts of using unchecked components are highlighted, showing their contribution to elevated failure rates, shortened product lifespans, and an estimated 20% increase in e-waste. By adopting a 100% inspection protocol, leveraging advanced technologies, and enforcing stringent material quality controls, manufacturers can significantly enhance the reliability of electronic products while reducing their environmental impact, thus fostering a more sustainable electronics industry.

Volatile compounds, abundant in breath, can be used to accurately diagnose and monitor a range of medical conditions. This offers a non-invasive, low-cost approach with screening applications; however, uptake of this diagnostic approach has been limited by conflicting published outcomes. Most published reports rely on large scale screening of the public, at single time points and without reference to ambient air. Here, we present a novel approach to volatile sampling from cellular headspace and mouse breath that incorporates multi-time point analysis and ambient air subtraction revealing compound flux as an effective proxy of active metabolism. This approach to investigating breath volatiles offers a new avenue for disease biomarker discovery and diagnosis. Using gas chromatography mass spectrometry (GC/MS), we focus on low molecular weight, metabolic substrate/by-product compounds and demonstrate that this non-invasive technique is sensitive (reproducible at ~1 µg cellular protein, or ~500,000 cells) and capable of precisely determining cell type, status and treatment. Isolated cellular models represent components of larger mammalian systems and we show that stress- and pathology-indicative compounds are detectable in mice, supporting further investigation using this methodology as a tool to identify volatile targets in human patients.

Immunoglobulin G (IgG) adopts a modular multidomain structure that mediates antigen recognition and effector functions, such as complement-dependent cytotoxicity. IgG molecules are self-assembled into a hexameric ring on antigen-containing membranes, recruiting the complement component, C1q. To provide deeper insights into the initial step of the complement pathway, we report a high-speed atomic force microscopy study for quantitative visualization of the interaction between IgG and the C1 complex composed of C1q, C1r, and C1s. Results showed that C1q in the C1 complex is restricted regarding internal motion and has a stronger binding affinity for on-membrane IgG assemblages than C1q alone, presumably because of smaller conformational entropy loss upon binding. Furthermore, we visualized a 1:1 stoichiometric interaction between C1/C1q and an IgG variant that lacks the entire CH1 domain in the absence of antigen. In addition to the canonical C1q-binding site on Fc, their interactions are mediated through a secondary site on the CL domain that is cryptic in the presence of the CH1 domain. Our findings offer clues for novel-modality therapeutic antibodies.

Redundancy in ship systems is provided to ensure operational resilience through equipment backups which ensures system availability and offline repairs of machinery. The electric power generation system of ships provides the most utility of all systems, hence is provided with good level of standby units to ensure reliable operations. Nonetheless, the occurrence of undesired black outs are common onboard ships and portends a serious danger to ship security and safety. Therefore, understanding the contributing factors affecting system reliability through component criticality analysis is essential to ensure a more robust maintenance and support platform for efficient ship operations. In this regard hybrid reliability and fault detection analysis were conducted to establish component criticality and related fault conditions. A case study was conducted on a ship power generation system consisting of 4 marine diesel power generation plants onboard an Offshore Patrol Vessel (OPV). Results from the reliability analysis indicate overall low system reliability of less than 70 per cent within the first 24 months of the 78 operational months. Component criticality using reliability importance measures was used to identify all components with more than 40 per cent contribution to sub systems failure. Additionally, machine learning was used to aid the reliability analysis through feature engineering and fault identification using Artificial Neural Networks classification. The ANN has identified failure patten threshold at about 200kva which can be attributed to overheating, hence establishing link between component failure and generator performance.

Plasma polymerized (PP) thin films deposited in a soft or intermediate plasma discharge from hexamethyldisiloxane (HMDSO) were developed as sensors for the detection of volatile organic compounds (VOCs) vapors. Energy dispersive X-ray spectroscopy (EDX) and X-ray reflectometry (XRR) were performed to determine the organosilicon films elemental composition and density. Spectroscopic ellipsometry measurements were carried out to determine the refractive index of the films. Quartz crystal microbalance (QCM) and ellipsometry coupled to vapor sorption were used to investigate the sorption mechanism of several VOCs vapors into the films as a function of the plasma deposition conditions. The density and the refractive index of the PP-HMDSO films increased with the plasma energy due to a different chemical composition and different proportion of free volumes in the material network. The PP-HMDSO films showed different affinities towards the VOCs vapors depending on the plasma discharge energy. The films elaborated in the lowest plasma energy revealed a good sensitivity towards the VOCs especially toluene (one of the BTEX vapors) compared to the other films deposited under higher plasma energy. In addition, the selectivity between toluene and other non-BTEX VOCs such as heptane and ethanol decreased to become zero while increasing the plasma energy.

Sparkling wine producing and consumption are in constant increase in the last decade and show no sign of slowing. Prior consumption, origin, grape variety, occasion, price and sensorial perception are factors that typically influence wine consumers’ purchasing and consumption behavior. The presence of volatile compounds in sparkling wines, with direct impact on their organoleptic characteristics, is influenced by several factors, such as the base-wine characteristics, grapes cultivar conditions, the used yeasts, the aging stage or wine-making practices. For this study, five sparkling wines variants from Muscat Ottonel grape variety were obtained. For the experimental samples, the grapes were processed by applying secondary fermentation in bottles. The base-wine was obtained through reverse osmosis and had a predetermined alcoholic concentration (10.5 % vol.). This study aimed to analyze the influence of different commercial yeasts (IOC FIZZ™, IOC DIVINE™, LEVULIA CRISTAL™, IOC 18-2007™) on the volatile composition of experimental sparkling wines. The obtained sparkling wines were characterized by the physical-chemical parameters (according to OIV methods of analysis) and volatile fraction (using gas-chromatography). Data showed an important impact on the concentration of the volatile compounds (p &lt; 0.05), depending on the type of inoculated yeast for the second fermentation and only a minor influence on the physical-chemical parameters was registered.

Volatile fatty acids (VFAs) are a group of common metabolites with a potential of universal infochemicals dedicated to transferring of information between higher organisms and bacteria either from microbiome or external environment. VFAs are common substances among various insect orders, there are numerous studies exploring their influence on the behavior of different insect species. In relation to papers published by J. E. McFarlane, we assess the effects of formic, acetic, propionic, butyric, valeric acids on spatial preference of common stored food grain products, and poultry industry pest – lesser mealworm (Alphitobius diaperinus). We present novel method of continuous, simultaneous assessment of site preference as well as travelled distance in constant-flow olfactometer. All tested VFAs except valeric had a significant repellent effect with formic acid being effective in the lowest concentration. Additionally, VFAs significantly altered distance travelled by insects. Obtained results indicate a potential role of VFAs in the olfactory guided behavior of A. diaperinus, we speculate that reaction to the presence if VFAs may deviate form specificity of species’ original habitat.

The massive amount of human biological, imaging and clinical data produced by multiple and diverse sources, necessitates integrative modeling approaches able to summarize all this information into answers to specific clinical questions. In this paper, we present a hypermodeling scheme able to combine models of diverse cancer aspects regardless of their underlying method or scale. Describing tissue-scale cancer cell proliferation, biomechanical tumor growth, nutrient transport, genomic-scale aberrant cancer cell metabolism, and cell signaling pathways that regulate the cellular response to therapy, the hypermodel integrates mutation, miRNA expression, imaging, and clinical data. The constituting hypomodels as well as their orchestration and links are described. Two specific cancer types, Wilms tumor (nephroblastoma) and non-small cell lung cancer, are addressed as proof of concept study cases. Personalized simulations over the actual anatomy of a patient have been carried out. The hypermodel has also applied to predict tumor control after radiotherapy and the relationship between tumor proliferative activity and response to neoadjuvant chemotherapy. Our innovative hypermodel holds promise as a digital twin based clinical decision support system and the core of future in silico trial platforms, although additional retrospective adaptation and validation is necessary.

We define a spinor-Minkowski metric for SL(4,C). It is not a trivial generalization of the SL(2,C) metric and it involves the Minkowskian one. We define 4x4 version of the Pauli matrices and eight 4-component associated generalized eigenvectors that can be regarded as undotted covariant spinors. The 4-component spinors can be grouped into four categories. Each category transforms in its own way. The outer products of pairwise combinations of 4-component spinors can be associated with 4-vectors. Including the dotted covariant, undotted and dotted contravariant forms totally we have sixteen pairs of spinors. Eight of them live in the conjugate space which has no countepart in SL(2,C).

Accurate analysis of continuous-wave electron spin resonance (cw ESR) spectra of biological or organic free-radicals and paramagnetic metal complexes is key to understand their structure-function relationships and electrochemical properties. Current method of analysis based on simulations often fail to extract the spectral information accurately. In addition, such analyses are highly sensitive to spectral resolution and artifacts, users’ defined input parameters and spectral complexity. We introduce a simulation-independent spectral analysis approach that enables broader application of ESR. We use a wavelet packet transform-based method for extracting g values and hyperfine (A) constants directly from cw ESR spectra. We show that our method overcomes the challenges associated with simulation-based methods for analyzing poorly / partially resolved and unresolved spectra, which is a common in most cases. The accuracy and consistency of the method are demonstrated on a series of experimental spectra of organic radicals and copper-nitrogen complexes. We showed that for a two-component system, the method identifies their individual spectral features even at a relative concentration of 5% for the minor component.

Fabrics comprised of porous fibers could provide effective passive protection against chemical and biological (CB) threats whilst maintaining high air permeability (breathability). Here, we fabricate hierarchically porous fibers consisting of regenerated silk fibroin (RSF) and activated-carbon (AC) prepared through two fiber spinning techniques in combination with ice-templating – namely cryogenic solution blow spinning (Cryo-SBS) and cryogenic wet-spinning (Cryo-WS). The Cryo-WS RSF fibers had exceptionally small macropores (as low as 0.1 µm) and high specific surface areas (SSAs) of up to 79 m2 g-1. The incorporation of AC could further increase the SSA to 210 m2 g-1 (25 wt. % loading) whilst also increasing adsorption capacity for volatile organic compounds (VOCs).

Analyzing big data poses a great challenge for numerous researchers to explore the data structure. Dimension reduction methods can be used to reduce data dimensionality, taking it from occupying a high-dimensional space to existing in a lower-dimensional space while retaining as much information as possible. Principal Component Analysis is one of the most popular used to reduce the dimensional space. The bootstrap sample is obtained by randomly sampling n times with replacement from the original sample, the method provides easy tool to understand the interactive component and develop the process. There are not enough researches discussed the stability of PCA method using bootstrap method. In this paper, the bootstrap method is used to analyze the stability of PCA results and to estimate the number of PCA in efficient way. The method is used to estimate the number of PCA that needed to classify the data set, and the effectiveness of the discussed techniques is demonstrated through real data sets.

In this study, the autofrettage method, which is used to increase the durability of cylindrical parts, was applied to a barrel made of steel material according to the AISI 4340 standard. Assuming that the barrel works continuously under the pressure of 400 MPa, optimum autofrettage was performed. The stresses occurring on the barrel before and after autofretage were calculated. Additionally, analytical equivalent stress values (Von-Mises) formed on the part's wall were compared with numerical analysis results obtained with a commercial finite element program ANSYS®, and their compatibility was examined. As a result of the calculations and analysis performed, it was observed that autofretage has positive effect on increasing the pressure carrying capacity of the barrel. After autofrettage the cylindrical part, it was determined that the Von-Mises stress values formed in the part wall changed and these stresses took the lowest value at a point (elastic-plastic interface). It has been evaluated that this point gives the optimal autofretage pressure value for a certain operating pressure. After the autofrettage application, it was determined that the Von-Mises Stress value in the barrel wall decreased by 25.27 % and the pressure carrying capacity of the barrel increased without any design or dimensional change. It has been seen that the analytical and numerical analysis results are consistent with each other, and it is expected that this study will guide and contribute to the studies to be conducted on increasing the strength or lightening the weight of the parts.

Principal component analysis (PCA) is used to reduce the dimensionalities of high dimensional datasets in a variety of research areas. For example, biological macromolecules, such as proteins, exhibit many degrees of freedom, allowing them to adopt intricate structures and exhibit complex functions by undergoing large conformational changes. Therefore, molecular simulations of and experiments on proteins generate a large number of structure variations in high dimensional space. PCA and many PCA-related methods have been developed to extract key features from such structural data, and these approaches have been widely applied for over 30 years to elucidate macromolecular dynamics. This review mainly focuses on the methodological aspects of PCA and related methods, and their applications for investigating protein dynamics.

The processes of hydrogen reduction of silicon and germanium chlorides under the conditions of radio-frequency (40.68 MHz) counteracted arc discharge stabilized between two rod electrodes were investigated. The main gas-phase and solid products of plasma-chemical transformations were determined. Thermodynamic analysis of SiCl4 + H2 and GeCl4 + H2 systems was carried out. It is shown that under the implemented experimental conditions, equilibrium components of the products are established. The detected spectra of chemical activity were studied, which gave reason to assume that the molecular mechanism of the hydrogen reduction process is the main one. The impurity composition of gas-phase and solid reaction products was investigated. The possibility of single-stage production of high-purity Si and Ge mainly in the form of compact ingots, as well as high-purity chlorosilanes and trichlorogermane, was shown.

Fungal infection of grape berries (Vitis vinifera) by Botrytis cinerea frequently coincides with harvest, impacting both the yield and quality of grape and wine products. A rapid and non-destructive method for identifying B. cinerea infection in grapes at an early stage prior to harvest is critical to manage loss. In this study, zeolitic imidazolate framework-8 (ZIF-8) crystal was applied as an absorbent material for volatile extraction from B. cinerea-infected and healthy grapes in a vineyard followed by thermal desorption gas chromatography-mass spectrometry. The performance of ZIF-8 to absorb and trap targeted volatiles was evaluated with a standard solution of compounds and with a whole bunch of grapes enclosed in a glass container to maintain standard sampling conditions. Results from sampling methods were then correlated to B. cinerea infection in grapes as measured and determined by Genus specific antigen quantification. Trace levels of targeted compounds reported as markers of grape B. cinerea infection were successfully detected with in-field sampling. Peak area counts for volatiles 3-octanone, 1-octen-3-one, 3-octanol, and 1-octen-3-ol extracted using ZIF-8 were significantly higher than values achieved using Tenax®-TA from field testing and demonstrated good correlation with B. cinerea infection severities determined by B. cinerea antigen detection.

Microbiota and the metabolites they produce within the large intestine interact with the host epithelia under the influence of a range of host-derived metabolic, immune, and homeostatic factors. This complex host-microbe interaction affects intestinal tumorigenesis but established microbial or metabolite profiles predicting colorectal cancer (CRC) risk are missing. Here we describe alterations in fecal bacteria and volatile organic compounds (VOC) in healthy (Non-Adenoma, NA) versus CRC prone (High-Risk Adenoma, HRA) individuals. Analyzing samples from 117 participants undergoing routine colonoscopy we highlight the higher abundance of Proteobacteria and Parabacteroides distasonis, and the lower abundance of Lachnospiraceae species, Roseburia faecis, Blautia luti, Fusicatenibacter saccharovorans, Eubacterium rectale and Phascolarctobacterium faecium, in the fecal samples of HRA individuals. Volatolomic analysis reveals higher concentration in the feces of HRA individuals of 5 compounds, isobutyric acid, methyl butyrate, methyl propionate, 2-hexanone and 2-pentanone. Interestingly, there is a level of complexity revealed by assessing fecal bacteria-VOC associations and another one by assessing differences in these associations between NA and HRA individuals. For example, isobutyric acid corelates positively with the Lachnospiraceae incertae sedis and Bacteroides genera in NA individuals, and negatively in HRA individuals. In contrast, Coprococcus and Colinsella genera correlate negatively with isobutyric acid in NA individuals, and positively in HRA individuals. The described differences in the fecal microbiota and VOC profiles and their associations in NA versus HRA individuals indicate the significance of multiple levels of combinatorial analysis towards the identification of testable CRC risk biomarkers.

Traditional grain vinegar is fermented using multiple acetic acid bacteria (AAB) at various temperatures. A single AAB showed high acid–producing ability at 30 °C with a 5% alcohol concentration and an initial pH adjusted to 4.0. Multiple AAB were similar to single AAB, but the optimal initial pH was 3.0. Acid production ability according to the type of AAB was higher in multiple AAB than that for single AAB. That is, using multiple AAB helped to increase the titratable acidity of traditional grain vinegar. In addition, increasing the titratable acidity and content of volatile flavor compounds was advantageous when two, rather than four, AAB types were mixed and used. Titratable acidity was high at medium temperatures (30 °C), but volatile flavor compounds increased at low temperatures (20 °C) under multiple AAB. A 16S rDNA–based microbiome taxonomic profiling analysis identified differences in beta diversity due to multiple AAB and fermentation temperatures. In particular, beta diversity analysis revealed a specific pattern when a mixture of Acetobacter ascedens GV–8 and Acetobacter pasteurianus GV–22 were fermented at low temperature (20 °C). Therefore, we propose the application of multiple AAB with acidic and flavor–producing properties in traditional grain vinegar.

Three-layer structures based on various multi-component films of III–V semiconductors heavily doped with Fe were grown by pulsed laser sputtering of InSb, GaSb, InAs, GaAs and Fe solid targets. The structures comprising InAsSb:Fe, InGaSb:Fe and InSb:Fe layers with Fe concentrations up to 24 at. % separated by GaAs spacers were deposited on (001) i-GaAs substrates at 200ºC. Transmission electron microscopy showed that the structures have a rather high crystalline quality and do not contain secondary-phase inclusions. X-ray photoelectron spectroscopy investigations revealed significant diffusion of Ga atoms from the GaAs regions into the InAsSb:Fe layers, which has led to the formation of an InGaAsSb:Fe compound with a Ga content up to 20 at. %. It has been found that the ferromagnetic properties of the InAsSb:Fe magnetic semiconductor improve with increasing Sb:As ratio. It has been concluded that the indirect ferromagnetic exchange interaction between Fe atoms occurs predominantly via Sb atoms.

Currently, two-component integrable nonlinear equations from the hierarchies of the vector nonlinear Schrodinger equation and the vector derivative nonlinear Schrödinger equation are being actively investigated. Usually, such two-component integrable nonlinear evolutionary equations are considered, the form of which does not depend on the replacement of one component with another. In this paper, we propose for consideration and usage a new hierarchy of two-component integrable nonlinear equations, which have an important difference from the already known equations. Among the hierarchy equations there are analogues of the two-component nonlinear Schrödinger equation (second equation from hierarchy) and the two-component modified Korteweg-de Vries equation (fourth equation from hierarchy). The third equation of the hierarchy is a combination of the nonlinear Schrödinger equation for one component and the modified Korteweg-de Vries equation for the second component. The equations for the individual components are very different from each other, even if they have the same order. Let us note that even hierarchy equations can be reduced to well-known variants of the scalar derivative nonlinear Schrödinger equations, and odd equations can’t be reduced. To construct the hierarchy equations, we use the monodromy matrix method, first proposed by B.A. Dubrovin. Knowledge of the monodromy matrix makes it possible to construct spectral curves of multiphase solutions, as well as to find stationary equations that these solutions satisfy. The last section presents the simplest solutions in the form of solitons and periodic one-phase waves, as well as spectral curves corresponding to these solutions.

This study aims to develop novel automated computer vision algorithms and systems for component replacement inspection for Printed Circuit Boards (PCBs). The proposed algorithms are able to identify locations as well as sizes of different components. They are object detection algorithms based on keypoints of the target components. The algorithms can be implemented as neural networks consisting of two portions: frontend networks and backend networks. The frontend networks are used for the feature extractions of input images. The backend networks are adopted for producing component inspection results. Each component class can has its own frontend and backend networks. In this way, the neural model for the component class can be effectively reused for different PCBs. To reduce the computation time for the inference of the networks, different component classes can share the same frontend networks. A two-stage training process is proposed for effectively exploring features of different components for accurate component inspection. The proposed algorithm has the advantages of the simplicity for training data collection, high accuracy for defect detection, and high reusability and flexibility for online inspection. The algorithm is an effective alternative for the automated inspection in smart factory with growing demand for product quality and diversification.

The coombs (in Catalan comes) form an integral part of the landscape. These are small valleys, with the deepest and flattest part cultivated for agriculture. They are predominantly found in the most arid regions of Catalonia, particularly around the cities of Tarragona and Lleida. They are generally dry land areas. We propose that these coombs gained significance in the early centuries of the Middle Ages, a period marked by intense erosion. It is important to identify their locations and establish connections with medieval written documents, the settlements that thrived throughout the Middle Ages, archaeological sites such as necropolises, and the valuable data derived from to-ponymy studies. We think that understanding these coombs can greatly contribute to under-standing how the territory was organized in the Middle Ages, the extent of cultivated lands that were established, and the distribution of many settlements. Ultimately, this knowledge can aid in acquiring better understanding of the current landscape.

The aim of this study was to examine whether H2O2, generated in such beverages as tea and coffee, is formed also in infusions of medicinal herbs and propose the possible mechanism of its formation. Infusions of sixteen herbs were studied and the presence of H2O2 was found in all cases. The highest concentrations of H2O2, exceeding 50 µM, were found in the infusions of leaves of Betula and Polygonum, and of the inflorescence of Tilia. These low amounts of H2O2 should not have a harmful effect and may even exert beneficial action, perhaps contributing to the health effects of the herbs. Generation of semiquinone and superoxide radicals was detected in herbal infusions, indicating that oxidation of phenolic compounds is the main source of H2O2 in these infusions. Herbal infusions were cytotoxic to human ovary cancer SKOV-3 and PEO1 cells; this cytotoxicity was compromised by catalase added to the growth medium, demonstrating the contribution of hydrogen peroxide to the cytotoxic action of herbal extracts.

The well-known coupling between the magnetic and electric fields in electromagnetic radiation is revisited in light of the recent introduction of a microscopic theory for the Ørsted magnetic field induction. I argue that, if the Ørsted magnetic field induction does indeed have a microscopic origin rather than the continuum solution offered by the Maxwell-Ampere equation, the "electromagnetic wave"' propagating in vacuum will not have a magnetic component.

In this paper, the quantum theory of the infinite-component Majorana field for the fermionic tower is formulated. This study proves that the energy states with increasing spin are simply composite systems made by a bradyon and antitachyons with half-integer spin. The quantum field describing these exotic states is obtained by the infinite sum of four-spinor operators, which each operator depends on the spin and the rest mass of the bradyon in its fundamental state. The interaction between bradyon-tachyon, tachyon-tachyon and tachyon-luxon has also been considered and included in the total Lagrangian. The obtained theory is consistent with the CPT invariance and the spin-statistics theorem and could explain the existence of new forms of matter not predictable within the standard model.

Beneficial microorganisms promote plant growth through different mechanisms, such as the production of plant hormones, the synthesis of 1-aminocyclopropane-1-carboxylic acid deaminase (ACCD), or, through volatile organic compounds (VOCs) emission. There are numerous studies describing a biostimulant action mediated by VOCs released by bacteria and filamentous fungi. However, in soil yeasts, research in this regard is still incipient. In a previous study, we present the stimulatory action of Solicoccozyma aeria YCPUC79 on tomato seedling growth by inoculating the rootzone with this yeast. The positive effect of S. aeria was related to the synthesis of indole acetic acid (IAA) and the presence of ACCD activity by the yeast. In the present study, we evaluated whether S. aeria is capable of emitting VOCs with biostimulant activity. For this, an experiment was conducted to test the release of VOCs in four treatments: S. aeria (Sa), tomato seedlings (T), tomato seedlings sharing the ambient with S. aeria but with no physical contact (TSa) plus a control with no yeast nor tomato seedlings (C). Tomato seedlings exposed to S. aeria in-oculum (TSa) presented 1.2-fold shorter main roots but increased the number of lateral roots by 80% compared to T. Regarding the analysis of VOCs, 59 compounds were identified excluding those found in the control treatment. These compounds represent twelve chemical families, in-cluding alcohols, esters, furans, hydrocarbons, ketones and terpenes. The treatment TSa shows an increased abundance of ketones, alcohols, esters, sulfur-containing compounds, and pyrazines in comparison to T treatment. Three compounds (butyl hept-4-yl ester-phthalic acid, (E)1.3-pentadiene and 1-propenylthiol) were exclusively present in the TSa treatment. This study provides, for the first time, information on a soil yeast capable of promoting the production of lateral roots in tomato through VOCs.

After the COVID-19 outbreak, more and more people are seeking physiological and psychological healing by visiting the forest as the time of stay-at-home became longer. NVOC, a major healing factor of forests, has several positive effects on human health, and this study researched about the NVOC characteristics of bamboo groves. The study revealed that α-pinene, 3-carene, and camphene were the most emitted, and the largest amount of NVOC was emitted in the early morning and late afternoon in bamboo groves. Furthermore, NVOC emission was found to have normal correlations with temperature and humidity, and inverse correlations with solar radiation, PAR and wind speed. A regression analysis conducted to predict the effect of microclimate factors on NVOC emissions resulted in a regression equation with 82.9% explanatory power and found that PAR, temperature, and humidity had a significant effect on NVOC emission prediction. In conclusion, this study investigated NVOC emission characteristics of bamboo groves, examined the relationship between NVOC emissions and microclimate factors and derived a prediction equation of NVOC emissions to figure out bamboo groves' forest healing effects. These results are expected to provide a basis for establishing more effective forest healing programs in bamboo groves.

Roses are one of the most important floricultural crops, and their essential oils have long been used for cosmetics and aromatherapy. We investigated the volatile compound compositions of 12 flower-color mutant variants and their original cultivars. Twelve rose mutant genotypes were developed by treatment with 70 Gy of 60Co gamma irradiation of six commercial rose cultivars. Essential oils from the flowers of the 18 genotypes were analyzed by gas chromatography–mass spectrometry. Seventy-seven volatile compounds were detected, which were categorized into five classes: hydrocarbons, terpenoids, alcohols, esters, and others. Hydrocarbons, alcohols, and esters were major components in all rose flowers. The mutant genotypes CR-S8 and CR-S9 showed higher contents of hydrocarbons than the original cultivar. In addition, CR-S1, CR-S3, and CR-S4 mutant genotypes showed higher ester contents than their original cultivar. Nonacosane, 2-methylhexacosane, and 2-methyltricosane were major volatile compounds among all genotypes. Hierarchical cluster analysis of the rose genotypes gave four groups according to grouping among the 77 volatile compounds. These findings will be useful for the selection of rose genotypes with improved volatile compounds.

Abstract Big datasets are becoming increasingly common and can be challenging to understand and apply in public health. One method for lowering the dimensionality of these datasets and improving interpretability while minimizing information loss is data reduction using principal component analysis (PCA). It achieves this by successively maximizing variance through the creation of new, uncorrelated variables. PCA is an adaptive data analysis technique because it simplifies the process of finding new variables, or principal components, by solving an eigenvalue or eigenvector problem. These new variables are determined by the dataset being used, rather than by the analyst starting from scratch. It is also adaptable in another way because varieties of the method have been designed to adjust to various data structures and types. However, there are serious problems in the theoretical understanding and practical application of PCA in public health researchers, whereas its application is becoming popular in developing countries. Therefore, this article, which concentrated on using PCA to reduce data, began by outlining the fundamental concepts of PCA and going over what it can and cannot do, as well as when and how to use it. We also discussed the fundamental assumptions, benefits, and drawbacks of PCA. Furthermore, this article demonstrated and resolved PCA practical application problems in public health that most scholars are unaware of, such as variable preparation, variable inclusion and exclusion criteria for PCA, iteration steps, wealth index analysis, interpretation, and ranking.

The testing of high-dimensional normality has been an important issue and has been intensively studied in literatures, it depends on the Variance-Covariance matrix of the sample, numerous methods have been proposed to reduce the complex of the Variance-Covariance matrix. The principle component analysis(PCA) was widely used since it can project the high-dimensional data into lower dimensional orthogonal space, and the normality of the reduced data can be evaluated by Jarque-Bera(JB) statistic on each principle direction. We propose two combined statistics, the summation and the maximum of one-way JB statistics, upon the independency of each principle direction, to test the multivariate normality of data in high dimensions. The performance of the proposed methods is illustrated by the empirical power of the simulated data of normal data and non-normal data. Two real examples show the validity of our proposed methods.

In this paper we review dynamics and roughness of bonds in proteins on example of albumin, that is important from the physiological point of view. We have performed computer simulations of albumin chain. Statistics were collected by performing many simulations realizations for each experimental setting. We concentrate on hydrogen bonds, cation-π and π- π interactions and NP contacts. Histograms of hydrogen bonds length are positively skewed in contrary to histograms of interactions and HP contacts that are negatively skewed. Scaling exponents of power spectra of energies of bonds / interactions /contacts are in range -0.2 to -0.5 and significantly differ between various hydrogen bonds or interactions. Varying scaling of such spectra can be used to classify between distinct bonds or contacts. Concerning particular amino-acids, largest amount of HBO H20 bonds are between Glutamate (GLU) amino-acids and water particle, while large amount of HBO bonds are formed with Lysine (LYS). For HP contacts the mayor role plays Phenylalanine (PHE) and Leucine (LEU) amino-acids. From decay curves HBO H2O bonds decays in fastest rate, while HBO bonds and HP contacts at slowest rate. We present as well decay curves of bonds formed by particular amino-acids, that gives interesting results.

Ulcerative colitis has a significant impact on the quality of life for the patients, and can substantially increase the risk of colon cancer in patients suffering long-term. Conventional treatments provide only modest relief paired with a high risk of side effects, while complementary and alternative medicines can offer safe and effective options. Over the past decade, we have shown that American ginseng has anti-oxidant and anti-inflammatory properties that can suppress mouse colitis and prevent colitis associated colon cancer. With the goal of isolating a single active compound, we further fractionated the hexane fraction, and found the most abundant molecule in this fraction was the polyacetylene, Panaxynol. After isolating and characterizing Panaxynol, we tested the efficacy of Panaxynol in the treatment and prevention of colitis in mice and studied the mechanism of action. We demonstrate here that Panaxynol effectively treats colitis in a Dextran Sulfate Sodium mouse model by targeting macrophages for DNA damage and apoptosis. Positive outcomes from this study could take American ginseng one-step further towards becoming a conventional drug for the treatment of colitis, and possibility exploring other autoimmune diseases associated with macrophage dysfunction.

Due to the low content, few studies are focused on the volatile compounds of Phlomoides rotata (Benth. ex Hook. f.) Mathiesen (PR, syn. Lamiophlomis rotata (Benth.) Kudô). However, such volatile compounds may have important pharmacological activities such as antioxidant, anticancer. In order to identify the chemical markers (CMs) in the essential oils (Es) and explore the potential bioactivities, we first conduct a thoroughly investigation on the volatile compounds and evaluate their anti-oxidant activities (AOAs), to the best of our knowledge. Light yellow Es with a fresh and elegant smell are obtained by hydro-distillation with an average yield of 0.11% (mL/g). After separation through cryoprecipitation, the crystals (Cs) and EOs removed crystals (RCs) were gotten, respectively. A total of 81 components are qualified and quantified in the Es, Cs and RCs, in which 44 ones are first reported from PR. As for content, the main compounds are long-chain fatty acids (LCFAs) and their esters. Among them, palmitic acid (PA), myristic acid (MA), linoleic acid (LA), oleic acid (OA) and methyl palmitate are highlighted, Besides, hexahydrofarnesyl acetone and phytol are also prominent Four kinds of C13-norisoprenoids are first reported from PR, in which, trans-β-damascenone is potent in flavour. In sum, these eight representative compounds can be chosen as the CMs. The AOAs of Es, Cs, RCs and four CMs such as PA, MA, LA and OA are evaluated by in vitro assays. In general, PA and MA present pro-oxidant activities (POAs) or weak AOAs. LA and OA show POAs or weak AOAs in lower concentration group, whereas demonstrate medium or strong AOAs in higher concentration group. Usually, the RCs demonstrate stronger AOAs and the Cs present weaker AOAs compared with those of the corresponding Es, which should be related to their different content of PA. This study can give some hints on the utilization of such Es which are abundant in LCFAs.

The promotion of plant growth and suppression of plant disease using beneficial microorganisms is considered an alternative to the application of chemical fertilizers or pesticides in the field. In this study, a coconut-scented antagonistic Trichoderma strain LZ42, previously isolated from Genoderma lucidum-cultivated soil, was investigated for biostimulatory and biocontrol functions in tomato seedlings. Morphological and phylogenetic analyses suggested that strain LZ42 is closely related to T. atroviride. Tomato plants showed increased aerial and root dry weights in greenhouse trials after treatment with T. atroviride LZ42 formulated in talc, indicating the biostimulatory function of this fungus. T. atroviride LZ42 effectively suppressed Fusarium wilt disease in tomato seedlings, with an 82.69% control efficiency, which is similar to that of fungicide treatment. The volatile organic compounds (VOCs) emitted by T. atroviride LZ42 were found to affect the primary root growth direction and promote the root growth of tomato seedlings in root Y-tube olfactometer assays. The fungal VOCs from T. atroviride LZ42 were observed to significantly inhibit F. oxysporum in a sandwiched Petri dish assay. SPME-GC-MS analysis revealed several VOCs emitted by T. atroviride LZ42; the dominant compound was tentatively identified as 6-pentyl-2H-pyran-2-one (6-PP). 6-PP exhibited a stronger ability to influence the direction of the primary roots of tomato seedlings but not the length of the primary roots. The inhibitory effect of 6-PP on F. oxysporum was the highest among the tested pure VOCs, showing a 50% effective concentration (EC50) of 5.76 μL mL-1 headspace. In conclusion, T. atroviride LZ42, which emits VOCs with multiple functions, is a promising agent for the biostimulation of vegetable plants and integrated management of Fusarium wilt disease.

To allow for a broad survey of subtle metabolic shifts in wine caused by rootstock and irrigation, an integrated metabolomics-based workflow followed by quantitation was developed. This workflow was particularly useful when applied to a poorly studied variety cv. Chambourcin. Allowing volatile metabolites that otherwise may have been missed with a targeted analysis to be included, this approach allowed deeper modeling of treatment differences which then could be used to identify important compounds. Wines produced on a per vine basis, over two years, were analyzed using SPME-GC-MS/MS. From the 382 and 221 features that differed significantly among rootstocks in 2017 and 2018 respectively, we tentatively identified 94 compounds by library search and retention index, with 22 confirmed and quantified using authentic standards. Own-rooted Chambourcin differed from other root-systems for multiple volatile compounds with fewer dif-ferences among grafted vines. For example, the average concentration of β-Damascenone present in own-rooted vines (9.49 µg/L) was significantly lower in other rootstocks (8.59 µg/L), whereas mean Linalool was significantly higher in 1103P rootstock compared to own-rooted. β-Damascenone was higher in regulated deficit irrigation (RDI) than other treatments. The workflow outlined not only was shown to be useful for scientific investigation, but also in creating a protocol for analysis that would ensure differences of interest to industry are not missed.

Onion (Allium cepa L.) is a strong-flavoring vegetable consumed in different ways. It is mainly due its distinctive flavor or simply pungency. Onion has also important natural compounds effective for medical functions such as inhibition of bone resorption, lower risk of cardiovascular disease and cancer. This importance is directly related to high content of organo-sulphur compounds. Shelf life of fresh onion bulb is short enough about two weeks at ambient storage conditions in Fogera district, Amhara region, Ethiopia. This is mainly due to the presence of high moisture in fresh onion bulbs. Postharvest loss of onion bulb reaches up to 50% in the production season in Fogera district. Consequently onion bulb had extreme variable market price during production and off season in the district which directly influences both the growers and consumers. In this study the effect of different drying techniques on nutritional and volatile components of onion were evaluated. Effect of different drying techniques on protein, carbohydrate, total sugar, fat, pyurvic acid, ascorbic acid, total phenol, total flovonol, rehydration ratio, color and sensory properties of onion slice were evaluated and found insignificant at (P > 0.05) for microwave and modified direct solar dryers taking fresh onion bulb as a control. But oven drying method had significant effect on onion physicochemical quality attributes at (P < 0.05) as compared to fresh onion bulbs.

Gelidium jelly was traditionally made by boiling processed Gelidium seaweed and allowing the filtrate to congeal into jelly. The processing of Gelidium seaweed was very complicate involved the repeated procedures of water washing and sun drying for 7 times, and the seaweed was originally purple-red in color turned into yellow after the repeated wash and sun drying. This study aimed to evaluate the effects of halogen lamp drying methods in replace of sun drying on the physical-chemical qualities of Gelidium jellies. Properties included the agar yield, gelling temperature, hardness, springiness, rheological parameters, sensory attributes, color, and volatile compounds were investigated. The results demonstrated halogen lamp drying method required 12 times of washing and drying processes to achieve the similar jelly properties compared to sun drying for 7 times in the experimental conditions. Volatiles including heptanal, β-ionone, and (E)-2-decenal could be used as indicators to monitor the washing and drying processing. Halogen lamp was found could be an alternative processing method for seaweed drying, especially at rainy days.

Bacillus species produce different classes of antimicrobial and antioxidant substances: peptides or proteins with different structural composition and molecular mass and a broad range of volatile organic compounds (VOCs), some of which may serve as biomarkers for microorganism identification. The aim of this study is the identification of biologically active compounds synthesized by five Bacillus species using gas chromatography coupled to mass spectrometry (GC–MS). The current study profoundly enhances the knowledge of antibacterial and antioxidant metabolites ensuring the unambiguous identification of VOCs produced by some Bacillus species, which were isolated from vegetable samples of potato, carrot, and tomato. Phylogenetic and biochemical studies were used to identify the bacterial isolates after culturing. Phylogenetic analysis proved that five bacterial isolates BSS12, BSS13, BSS16, BSS21, and BSS25 showed 99% nucleotide sequence similarities with Bacillus safensis AS-08, Bacillus cereus WAB2133, and Bacillus acidiproducens NiuFun, Bacillus toyonesis FORT 102 and Bacillus thuringiensis F3, respectively. The crude extract was prepared from bacterial isolates to assess the antibiotic resistance potency and the antimicrobial potential against various targeted multidrug-resistant strains, including Candida albicans, Candida krusei, Enterococcus hirae, Escherichia coli, Klebsiella aerogenes, Klebsiella pneumoniae, Staphylococcus aureus, Staphylococcus epidermidis, Streptococcus group B, Streptococcus mutans, Shigella sonnei, Salmonella enteritidis, Serratia marcescens, Pseudomonas aeruginosa, and Proteus vulgaris. GC–MS analysis of bacterial strains found that VOCs from Bacillus species come in a variety of chemical forms, such as ketones, alcohols, terpenoids, alkenes, etc. Overall, 69 volatile organic compounds were identified from five Bacillus species, and all five were found to share different chemical classes of volatile organic components, which have a variety of pharmacological applications. However, 8 antibacterial compounds with different concentrations were commonly found in all five species: acetoin, acetic acid, butanoic acid, 2-methyl-, oxime-, methoxy-phenyl, phenol, 1,2-benzenedicarboxylic acid, bis(2-methylpropyl) ester, nonanoic acid, and hexadecanoic acid, methyl. The biology and physiology of Bacillus can be better understood using these results, which can also be used to create novel biotechnological procedures and applications. Moreover, because of its exceptional ability to synthesize and produce a variety of different antibacterial compounds, Bacillus species can serve as natural and universal carriers for antibiotic compounds in the form of probiotic cultures and strains to fight different pathogens, including mycobacteria.

This study was aimed to investigate the effect of xylan depolymerizing enzyme namely endo-xylanase (Xyn) combined with debranching enzymes namely arabinofuranosidase (Afd) and feruloyl esterase (FE) on digestion, growth performance and intestinal volatile fatty acid profile of piglets. The in vitro experiments were firstly conducted to examine the enzymological properties of Xyn, Afd and FE, the synergy among these enzymes, together with the effect of combination of these enzymes on digestion of piglet diet. The in vivo experiment was then implemented by allocating 270 35-d-old postweaning piglets into 3 treatment groups: control group, Xyn group and (Xyn+Afd+FE) group. Each group had 6 replicates (15 piglets/replicate). The results revealed a satisfying thermostability and pH stability of Xyn, Afd and FE. Combination of Xyn, Afd and FE had a superiority (P < 0.05) over Xyn alone and its combination with Afd or FE in promoting degradation of different bran fibers rich in arabinoxylan (Abx). Treatment with combination of Xyn, Afd and FE had advantages over Xyn alone to induce increasing trends (P < 0.10) of in vitro digestibility of dietary nutrients (dry matter, crude protein, crude ash and gross energy) and piglet growth performance (average daily gain, final body weight and feed efficiency), concurrent with a reduction (P < 0.05) of diarrhea rate and increases (P < 0.05) in cecal acetic acid, butyric acid and total volatile fatty acids concentrations as well as pH value of piglets. Collectively, combination of Xyn, Afd and FE was efficient in benefiting degradation of Abx in brans, as well as improving digestion, growth performance and intestinal volatile fatty acid profile of piglets.

Essential oils are mixtures of compounds obtained from plants, including flowers, roots, bark, leaves, seeds,peel, fruits, wood, that have risen up in the last decades thanks to their beneficial properties as antibacterial, antifungal and anti-inflammatory agents. The aim of this study was to characterize and analyze 13 different commercial essential oils with two different techniques. The first is GC-MS, coupled with SPME, thanks to which 204 different VOCs have been identified. The results show that a total of 95 compounds was found only in one oil, while the others were found with different frequencies in many of them. The most represented class is that of terpenes, as widely reported in literature. The second technique is based on an array of chemical gas sensors. This system was used to investigate whether sensors are able to identify these products. It turned out that basil, cinnamon and carnation are the most identifiable oils with different number and typology of sensors, especially tin oxide and copper oxide nanowires, while cayeput and thyme are more mistakable samples. Thanks to this detailed study, it has been possible to reach and obtain novel insights for the future development of this type of research.

For Lentinula edodes, its characteristic flavor is the key determinant for consumer pref-erences. However, the tissue-specific volatile flavor variations of the fruiting body have been overlooked. Here, we comprehensively investigated volatile flavor profiles of different tissues including the pileus skin, context, gill and stipe of the fruiting body of two widely cultivated L. edodes strains (T2 and 0912). We show that the eight-carbon and sulfur com-pounds, which represented 43.2-78.0% and 1.4-42.9% to the total volatile emissions for strain 0912 and T2, dominated their volatiles profiles. The sulfur compounds could rep-resent 32.2% and 42.9% to the total volatile emissions for the context of the strain 0912 and T2, respectively, whereas only represented 1.4% for the stipes of the strain 0912 and 9.0% for the skin of strain T2. Proportions of the predominant C8 compounds (1-Octen-3-one, 1-Octen-3-ol and 3-Octanone) and sulfur compounds (Lenthionine, 1,2,4-Trithiolane, Di-methyl disulfide and Dimethyl trisurfide) changed depending on tissues and strains. We further reveal that the overall volatile flavor profiles varied greatly in different tissues and strains. With machine learning algorithm, we show that volatile profiles could 100% pre-dict strains 0912 and T2. The prediction accuracy for different tissues could also reach 100%. Our results highlight the tissue-specific volatile flavor variations of the L. edodes fruiting body.

This work develops a new method for vector data augmentation. The proposed method applies the Principal Component Analysis (PCA) and determines the Eigenvectors of a set of training vectors for a Machine Learning (ML) method and uses them to generate the distilled vectors. The training and the PCA distilled vectors have the same dimension. The user chooses the number of vectors to be distilled and augmented to the set of training vectors. A statistical approach determines the lowest number of vectors to be distilled such that when augmented to the original vectors the extended set trains a ML classifier to achieve a required accuracy. Hence, the novelty of this study is, the distillation of vectors with the PCA method and their use to augment the original set of vectors. The advantage that comes from the novelty is that it increases the statistics of ML classifiers. To validate the advantage, we conducted experiments with four public databases and applied four classifiers: Neural Network, Logistic Regression, Support Vector Machine with linear and polynomial kernels. For the purpose of augmentation, we conduct several distillations including nested (double distillation). The latter notion means that new vectors were distilled from already distilled vectors. We train the classifiers with three sets of vectors: original vectors; original augmented with vectors distilled by PCA; original augmented with distilled and double distilled, by PCA, vectors. The experimental results are presented in the paper, and they confirm the advantage that the PCA distilled vectors increase the classification statistics of ML methods, if the distilled vectors augment the original training vectors.

This study introduces a new procedure for three-component spectral matching of seismic ground acceleration records. The procedure involves preserving the phase angle and varying the Fourier amplitudes to match the spectra of the recorded records with a provided target spectrum that represents the spectral values of ground motions in three orthogonal directions. Several three-component recorded records were matched against two target response spectra to test the method. An accurate convergence was achieved in the velocity and displacement records. In addition, the scales among the components’ magnitude were maintained, creating realistic three-component ground motions. Such ground motion inputs are important to qualify critical structures sensitive to three-component motions. Our proposed procedure is novel because the present practices are mostly created based on one-component ground motions.

Read-Across Structure-Activity Relationship (RASAR) is an emerging cheminformatic approach that combines the usefulness of a QSAR model and similarity-based Read-Across predictions. In this work, we have generated a simple, interpretable, and transferable quantitative-RASAR (q-RASAR) model which can efficiently predict the cytotoxicity of TiO2-based multi-component nanomaterials. The data set involves 29 TiO2-based nanomaterials which contain specific amounts of noble metal precursors in the form of Ag, Au, Pd, and Pt. The data set was rationally divided into training and test sets and the Read-Across-based predictions for the test set were generated using the tool Read-Across-v4.1 available from https://sites.google.com/jadavpuruniversity.in/dtc-lab-software/home. The hyperparameters were optimized based on the training set data and using this optimized setting, the Read-Across-based predictions for the test set were obtained. The optimized hyperparameters and the similarity approach, which yields the best predictions, were used to calculate the similarity and error-based RASAR descriptors using the tool RASAR-Desc-Calc-v2.0 available from https://sites.google.com/jadavpuruniversity.in/dtc-lab-software/home. These RASAR descriptors were then clubbed with the physicochemical descriptors and were subjected to features selection using the tool Best Subset Selection v2.1 available from https://dtclab.webs.com/software-tools. The final set of selected descriptors was used to develop multiple linear regression based q-RASAR models, which were validated using stringent criteria as per the OECD guidelines. Finally, a random forest model was also developed with the selected descriptors. The final machine learning model can efficiently predict the cytotoxicity of TiO2-based multi-component nanomaterials superseding previously reported models in the prediction quality.

Micro turbojets are used for propelling radio-controlled aircraft, aerial targets and personal air vehicles. When compared to full-scale engines, they are characterized by relatively low efficiency and durability. In this context, the degraded performance of gas path components could lead to an unacceptable reduction in the overall engine performance. In this work, a data-driven model based on a conventional Artificial Neural Network (ANN) and an extreme learning machine (ELM) was used for estimating the performance degradation of the micro turbojet. The training datasets containing the performance data of the engine with degraded components were generated using the validated GSP model and the Monte Carlo approach. In particular, compressor and turbine performance degradation were simulated for three different flight regimes. It was confirmed that component degradation had a similar impact in flight than at sea level. Finally, the datasets were used in the training and testing process of the ELM algorithm with four different input vectors. Two vectors had an extensive number of virtual sensors, and the other two were reduced to just fuel flow and Exhaust Gas Temperature. Even with the small number of sensors, the high prediction accuracy of ELM was maintained for takeoff and cruise but was slightly worse for variable flight conditions.

Multispectral remote sensing data may contain component images which are heavily corrupted by noise and pre-filtering (denoising) procedure is often applied to enhance these component images. To do this, one can use reference images – component images having relatively high quality and which are similar to the image subject to pre-filtering. Here we study the following problems: how to select component images that can be used as references (e.g., for the Sentinel multispectral remote sensing data) and how to perform the actual denoising. We demonstrate that component images of the same resolution as well as component images of a better resolution can be used as references. Examples of denoising of real-life images demonstrate high efficiency of the proposed approach.

Anomaly occurrences in hydraulic machinery may lead to massive systems shut down, jeopardizing the safety of the machinery and its surrounding human operator(s) and environment, and the severe economic implications succeeding the faults and their associated damage. Hydraulics are mostly placed in ruthless environments, where they are consistently vulnerable to many faults. Hence, not only the machines and their components are prone to anomalies, but also the sensors attached to them, which monitor and report their health and behavioral changes. In this work, a comprehensive applicational analysis of anomalies in hydraulic systems extracted from a hydraulic test rig is thoroughly achieved. Firstly, we provided a combination of a new architecture of LSTM autoencoders and supervised machine and deep learning methodologies to perform two separate stages of fault detection and diagnosis. The two phases are condensed by: the detection phase using the LSTM autoencoder. Followed by the fault diagnosis phase represented by the classification schema. The previously mentioned framework is applied to both component and sensor faults in hydraulic systems, deployed in the form of two in-depth applicational experiments. Moreover, a thorough literature review of the past decade related work for the two stages separately is successfully conducted in this paper.

The genus Beauveria include important entomopathogenic and endophytic fungi, among them, Beauveria bassiana is the most studied species. However, there are few knowledge regarding their antimicrobial activity. The current research has been conducted to evaluate in vitro antagonistic activity of B. bassiana and the antimicrobial efficacy of its Exo and Endo metabolites against Bacillus cereus, B. megaterium, Clavibacter michiganensis (gram positive bacteria, G+ve), Xanthomonas campestris, Pseudomonas aeruginosa and P. fluorescence (gram negative bacteria, G-ve). In addition, Solid-phase microextraction (SPME) was coupled to Gas Chromatography-Mass Spectrometry (GC/MS) to qualitatively measure the volatile organic compounds (VOCs) metabolic profile of the most efficient studied isolate of B. bassiana. The obtained results showed that, the isolate UniB2439-3 has promising antibacterial effect against most of studied target bacteria. SPME-GC/MS analysis of VOCs revealed the presence of ethanol; butanal,2-methyl; 2,4-dimethyl-1-heptene; octane, 4-methyl and β-elemene as the main dominant bioactive compounds. The outgoing results explicated that the efficient isolate of B. bassiana can be potentially used as a biocontrol agent against several bacteria especially G+ve ones.

Some studies investigated the relationship between frequency domain analysis of heart rate variability and the cognitive performance at the Stroop task. We propose a combined assessment also of trunk mobility in 72 healthy women to investigate the relationship between cognitive, cardiac and motor variables based on a principal component analysis. We also assessed the change on this result after an intervention of two months aiming at improving the perception-action link. At baseline, the PCA correctly identified 3 components: one related to cardiac variables, one to trunk motion and one to the performance of Stroop task. After the intervention, only two components were found with trunk symmetry and range of motion, accuracy and time to complete the Stroop task and low frequency heart rate variability aggregated in a single component by PCA. It suggested that this protocol was effective in investigating the embodied cognition and we defined this approach as “embodimetrics”.

State Forest Management Organizations (SFMOs) play a crucial role in the European forest sector, managing almost half the forests in the region. SFMOs are often managed for timber production only whereas, being publicly owned, they should play an important role in providing a vast range of public goods (e.g. soil protection, biodiversity conservation). Their management goals depend on the history and current conditions of the forest sector at a national level, as well as different challenges and the potential for development. Although there is a lack of knowledge about the current performance of SFMOs, there have been recent changes to their management goals and practices in response to the new demands expressed by society (e.g. transparency, social inclusion). The main purpose of this study is to analyse the current situation of SFMOs by clustering them according to indicators that reflect three pillars of the common understanding of sustainable forest management (SFM) concept. With the help of Principal Component Analysis (PCA), we grouped countries according to common characteristics of the forest sector at the national level. Results show three main clusters of SFMOs in Europe. The first cluster has rather small but commercially-oriented forestry unit together with other business activities and a strong focus on public services. The second sees itself as the protector of public interest, rather than commercially-oriented organisations. The third is mainly profit-seeking. The existence of diverse SFMO clusters shows the possibility of different approaches for SFM with a focus on different goals (e.g. profit gaining, public service delivery).

Citrus essential oils (EOs) have various bioactivities like antioxidants, with many applications. Antioxidant activities depend on the chemical compositions of the EOs, which are affected by climate, soil, and geographical region. Thus, investigations on chemical compositions and antioxidant activities of Citrus EOs in different countries are valuable. In this study, we distilled EOs from peels of Indonesian-grown Citrus, including C. nobilis, C. limon, C. aurantifolia, C. amblycarpa, and Citrus spp.Chemical compositions of EOs were analyzed using Gas Chromatography-Mass Spectrometer (GC-MS), whereas the antioxidant activities were determined by employing 2,2-diphenyl-2-picrylhydrazyl (DPPH) method. Furthermore, principal component analysis (PCA) was applied to elucidate the main contributing compounds for antioxidant activity. The results show that all EOs possess unique chemical characteristics, with limonene as the majority constituent. For antioxidant activities, C. limon and C. amblycarpa EOs are the two strongest, IC50 values below 7.00 μL/mL. PCA approach suggests that -terpinene mainly contributes to the high antioxidant activities of C. limon and C. amblycarpa. Moreover, o-cymene, thymol, p-cymene, and α-pharnesene may also be responsible for the antioxidant activity of C. limon EO. These results are valuable information for the applications of Citrus EOs as antioxidant sources.

Cured-in-place pipe (CIPP) lining is a widely adopted method for pipeline renewal, offering advantages such as rapid installation and cost-effectiveness. However, concerns regarding the environmental impacts of volatile organic compound (VOC) emissions during the installation process have raised issues regarding the CIPP method. The literature review conducted in this paper indicated the need for stringent monitoring and management practices to mitigate adverse effects, emphasizing the importance of safe installation protocols. This paper presents the initial results of a case study focusing on VOC emissions, specifically investigating non-styrene polyester resins and water curing. To capture emissions from CIPP activities, the methodology involved air sampling using various equipment, including photoionization detectors (PID), summa canisters, passive worker sampler sorbent tubes, and method 13 cartridges. The preliminary findings indicate that non-styrene polyester resins do not exceed the exposure limits set out by the OSHA and USEPA. The future phases of this project will explore different resins and curing methods.

ABSTRACT The present study aimed to investigate the presence of asymmetric stochastic volatility and leverage effects within the Nasdaq-100 index. This index is widely regarded as an important indicator for investors. We focused on the nine leading stocks within the index, which are highly popular and hold significant weight in the investment world. These stocks are Netflix, PayPal, Google, Intel, Microsoft, Amazon, Tesla, Apple, and Meta. The study covered the period between 03/01/2017 and 30/01/2023, and we employed the Eviews and WinBUGS applications to conduct the analysis. We began by calculating the logarithmic difference to obtain the return series. We then performed a sample test with 100,000 iterations, excluding the first 10,000 samples to eliminate the initial bias of the coefficients. This left us with 90,000 samples for analysis. Using the results of the asymmetric stochastic volatility model, we evaluated both the Nasdaq-100 index as a whole and the volatility persistence, predictability, and correlation levels of individual stocks. This allowed us to evaluate the ability of individual stocks to represent the characteristics of the Nasdaq-100 index. Our findings revealed a dense clustering of volatility, both for the Nasdaq-100 index and the nine individual stocks. We observed that this volatility is continuous but has a predictable impact on variability. Moreover, with the exception of Intel, all the stocks in the model exhibited both leverage effects and the presence of asymmetric relationships, as did the Nasdaq-100 index as a whole. Overall, our results show that the characteristics of stocks in the model are similar to the volatility characteristic of the Nasdaq-100 index and have the ability to represent it.

Experimental optimization of analytical methods based on solid-phase microextraction (SPME) is a complex and labor-intensive process associated with uncertainties. Using the theoretical basics of SPME and finite element analysis software for the optimization proved to be an efficient alternative. In this study, an improved finite element analysis-based model for SPME of volatile organic compounds (VOCs) by porous coatings was developed mainly focussing on the mass transport in coatings. Benzene and the Carboxen/polydimethylsiloxane (Car/PDMS) coating were used as the model VOC and a porous SPME coating, respectively. It has been established that in the coating, volumetric fractions of Carboxen, PDMS, and air are 33, 42 and 24%, respectively. Knudsen diffusion in micropores can slow down a mass transport of analytes in the coating. When PDMS was considered as the solid part of the coating, lower root-mean-square deviation of the modeling results from experimental data was observed. It has been shown that the developed model can be used to model the extraction of VOCs from air and water samples encountered in a typical SPME development method procedure. It was possible to determine system equilibration times and use them to optimize sample volume and Henry’s law constant. The developed model is relatively simple, fast, and can be recommended for optimization of extraction parameters for other analytes and SPME coatings. The diffusivity of analytes in a coating is an important property needed for improved characterization of existing and new SPME polymers and analytical method optimization.

In this research, an attempt was made to reduce the dimension of wavelet-ANFIS/ANN (artificial neural network/adaptive neuro-fuzzy inference system) models toward reliable forecasts as well as to decrease computational cost. In this regard, the principal component analysis was performed on the input time series decomposed by a discrete wavelet transform to feed the ANN/ANFIS models. The models were applied for dissolved oxygen (DO) forecasting in rivers which is an important variable affecting aquatic life and water quality. The current values of DO, water surface temperature, salinity, and turbidity have been considered as the input variable to forecast DO in a three-time step further. The results of the study revealed that PCA can be employed as a powerful for dimension reduction of input variables and also to detect inter-correlation of input variables. Results of the PCA-Wavelet-ANN models are compared with those obtained from Wavelet-ANN models while the earlier one has the advantage of less computational time than the later models. Dealing with ANFIS models, PCA is more beneficial to avoid Wavelet-ANFIS models creating too many rules which deteriorate the efficiency of the ANFIS models. Moreover, manipulating the Wavelet-ANFIS models utilizing PCA leads to a significant decreasing in computational time. Finally, it was found that the PCA-Wavelet-ANN/ANFIS models can provide reliable forecasts of dissolved oxygen as an important water quality indicators in rivers.

The Independent Component Analysis (ICA) has been recently introduced as a reliable alternative to identify canonical scattering mechanisms within Polarimetric Synthetic Aperture Radar (PolSAR) images. This manuscript addresses two important aspects when applying such methods on real data, namely speckle filtering and statistical classification with ICA. A novel PolSAR data processing framework is introduced by adjusting the Lee's sigma filter to the particular nature of the Touzi's polarimetric decomposition. In its current form, it allows the use of the ICA mixing matrix in the derived speckle filter. An extension of the Fromont at al. iterative segmentation is introduced, equally. This proposed framework is tested using P band airborne PolSAR data acquired for the ESA campaign TropiSAR campaign.

Introduction and objectives: a close association between metabolic syndrome among subjects with erectile dysfunction has been addressed, since mechanisms underlying metabolic syndrome compromise the blood flow to the penis in numerous ways. This study aims to analyze the relationship between erectile dysfunction and metabolic syndrome in a group of Mexican patients, to study the influence of other morbidity factors on erectile dysfunction, and to define the specific metabolic syndrome components most associated with erectile dysfunction severity. Methods: a descriptive and cross-sectional study was completed in a group of 86 adult Mexican patients with previous diagnosis of erectile dysfunction. Participants were classified as with or without metabolic syndrome. Erectile dysfunction severity, alcohol or tobacco consumption, and depressive behavior were identified through validated questionnaires and compared between both groups, as well as anthropometric, biochemical, and clinical parameters. Results: anthropometric measures, laboratory values, clinical characteristics and the Beck Depression Inventory score were significantly different among both groups. Additionally, more patients affected by severe and moderate erectile dysfunction were identified in the group with metabolic syndrome. Among the metabolic syndrome components, HbA1c >5.7% and fasting glucose >110 mg/dl were significantly associated to the development of erectile dysfunction (p = 0.004 and 0.04, respectively). Conclusions: metabolic syndrome components aggravate erectile dysfunction, particularly the lack of glycemic control manifested by Hb1Ac >5.7% and/or fasting glucose >110 mg/dL. The inclusion of fasting glucose and HbA1c as a complementary biochemical screening among patients with erectile dysfunction should be assessed.

Background The Delta Neutrophil Index (DNI), a prodiagnostic marker for sepsis, utilizes leukocyte count. Platelet activation, similar to leukocytes, plays a crucial role in host defence against pathogens and may serve as a predictor of sepsis outcome. However, the combined evaluation of Mean Platelet Component (MPC) and DNI in assessing sepsis has been rarely used. Methods To assess the prodiagnostic validity of simultaneous utilization of DNI and MPC in cases of human febrile sepsis, we conducted measurements of cellular indices, including DNI and MPC, as well as molecular biomarkers such as procalcitonin (PCT) and C-reactive protein (CRP). This study was carried out on patients admitted to the emergency department with suspected sepsis. Results Using a cutoff value of 2.65%, the sensitivity, specificity, positive predictive value (PPV), and negative predictive value (NPV) of DNI in sepsis were found to be 69%, 73.9%, 77.9%, and 64.1%, respectively. Furthermore, significant differences in DNI and MPC levels were observed between the sepsis and non-sepsis groups (6.7±7.8% versus 2.1±2.2%, P=0.000 and 26.0±1.9 g/dl versus 26.8±1.4 g/dl, P=0.002), respectively. Notably, there was a negative correlation between DNI and MPC, with the strength of the correlation varying based on the cause of sepsis. By setting the cutoff value for DNI at 6.2%, the sensitivity, specificity, and NPV improved to 100%, 80.3%, and 100%, respectively, although the PPV remained at 10.6%. Importantly, the DNI≥6.2 group exhibited a higher incidence of death (10.9%, 5/46) and multiorgan failure (19.6%, 9/46) compared to the DNI<6.2 group (0.0%, 0/46 and 0.0%, 0/167, respectively) (P=0.000 and P=0.000, respectively). Conclusions In our study, DNI demonstrates superior effectiveness compared to other molecular biomarkers such as CRP and procalcitonin in distinguishing febrile septic patients from febrile nonseptic patients and predicting prognosis. Additionally, there exists a negative correlation between MPC and DNI, making MPC a valuable marker for differentiating the etiology of sepsis. These findings hold significant clinical implications as DNI/MPC is a cost-effective and readily applicable approach in various impending sepsis scenarios. Notably, this study represents the first examination of the prodiagnostic validity of simultaneously employing DNI and MPC in human cases of febrile sepsis.

The (benzylthio)acetic acid (HBTA) and some aminopyrimidines, namely 2-aminopyrimidine (2-AP), 5-aminopyrimidine (5-AP), 2-amino-4,6-dimethylpyrimidine (2-A-4,6-DMP) and 2,4,6-triaminopyrimidine (2,4,6-TAP), were successfully embodied as structural units into the construction of a total of four novel supramolecular organic frameworks. The received crystalline solids were inspected by single crystal X-ray diffraction (SC XRD) in order to obtain insight into the structural and supramolecular facets. The SOFs deriving from 2-AP, 5-AP as well as 2-A-4,6-DMP crystallize in the form of true co-crystals (1-3), while the one originating from 2,4,6-TAP crystallizes as salt solvate (4). The SC XRD results indicated the different contents of structural residues present in the asymmetric units of the crystals 1-4 despite the using the same molar ratio of molecular co-formers in each case. The molecular structures of co-crystals 1-3 consist of either one neutral residue of each starting components (1 and 3) or a half nonionized residue of aminopyrimidine ingredient and one neutral residue of acidic specie (2). The asymmetric unit of salt solvate 4 is composed of two ionized residues of each co-former (two 2,4,6-TAP+ cations and two BTA- anions) and one MeOH solvent molecule. The most extensive H-bonding network is observed in the crystal structure of salt solvate 4. The relevant molecular ingredients in co-crystals 1-3 are mainly hold together by the neutral Ocarboxylic–H···Npyrimidine and Namine–H···Ocarboxylic H-bonds. In the case of aggregate 4, the corresponding ionic residues are predominantly sustained by the charged-assisted Npyrimidinium–H···Ocarboxylate and Namine–H···Ocarboxylate hydrogen interactions. The MeOH solvent incorporated into the crystal lattice of adduct 4 is also involved in H-bonding by simultaneously serving as the single donor in OMeOH–H···S and the single acceptor in Namine–H···OMeOH H-bonds afforded the structural diversity within the 2,4,6-TAP+ cations and BTA- anions. Other weaker sets of additional non-covalent contacts existing in the crystal structures of analyzed conglomerates are involved in the self-assembly, stabilization and expansion of total supramolecular organic frameworks. The fact of the formation of non-covalent bonded supramolecular organic frameworks in question is also reflected in corresponding results obtained through elemental analysis (EA), Fourier transform infrared spectroscopy (FT−IR) and thermal analysis (TG/DSC).

Cardiovascular disease is the number one cause of death in the world and Quoting from WHO, around 31% of deaths in the world are caused by cardiovascular diseases and more than 75% of deaths occur in developing countries. The results of patients with cardiovascular disease produce many medical records that can be used for further patient management. This study aims to develop a method of data mining by grouping patients with cardiovascular disease to determine the level of patient complications in the two clusters. The method applied is principal component analysis (PCA) which aims to reduce the dimensions of the large data available and the techniques of data mining in the form of cluster analysis which implements the K-Medoids algorithm. The results of data reduction with PCA resulted in five new components with a cumulative proportion variance of 0.8311. The five new components are implemented for cluster formation using the K-Medoids algorithm which results in the form of two clusters with a silhouette coefficient of 0.35. Combination of techniques of Data reduction by PCA and the application of the K-Medoids clustering algorithm are new ways for grouping data of patients with cardiovascular disease based on the level of patient complications in each cluster of data generated.

The Inefficient water use, varying and low productivity in Kenya public irrigation schemes is a major concern. It is therefore necessary to periodically monitor and evaluate the performance of public irrigation schemes. The performance of public irrigation in western Kenya was assessed by combining benchmarking methodology and principal component analysis. The aim was to quantify and rank the performance of pumped public irrigation schemes in Kenya. Eleven benchmarking indicators were computed for the period from 2012 to 2016 and compared to global benchmark values. The indicators used fall under agricultural productivity, water supply and financial performance categories. The computed agricultural productivity was 36%–51% in Ahero, 23%–42% in West Kano and 26%–50% Bunyala irrigation scheme. Water supply performance in Ahero, West Kano and Bunyala irrigation schemes varied from 24% to 58%, 3% to 49% and 19% to 43% respectively. Financial performance varied from 46% to 54% in Ahero, 25% to 32% in West Kano and 54%–56% in Bunyala irrigation scheme. An average overall performance efficiency of 46%, 39% and 31% was obtained in Ahero, Bunyala and West Kano irrigation schemes respectively. The performance of the irrigation schemes is very poor and measures on improving performance are needed.

The volatile fatty acids (VFAs) productions, as well as particulate organics decomposition, soluble chemical oxygen demand (SCOD) yield, and the VFAs production pathways, of mesophilic and thermophilic anaerobic fermentation were investigated. Batch experiments showed that the decomposition rate of volatile suspended solids (VSS), particulate carbohydrate (P-C) and particulate protein (P-P) followed the first-order kinetic model at different temperature. However, the intermediates， accumulated in the process of protein or carbohydrate digestion had a more significant inhibitory effect on the production of VFAs during the mesophilic anaerobic acidification process. Thermophilic fermentation led to more accumulation of VFAs compared to mesophilic fermentation. Then 13C stable isotope labeling experiment demonstrated that, acetic (HAc), propionic (HPr) and butyric (HBu) could be produced from carbohydrate and protein digestion, but valeric (HVa) was only generated from the degradation of protein. Finally, the possible pathway of HVa synthesis was proposed.

Background: Metastasis is a complex process that involves the spread of the tumor to distant parts of the body from its original site. Metastatic dissemination represents the main physiopathology of cancer. Soluble factors such as cytokines have been closely related to breast cancer (BC) metastasis. Bisphenol A (BPA) is an endocrine disrupting chemical compound with estrogenic properties, which exposure in the early stages of neonatal life leads to an increase in the size and weight of breast tumors and cellular changes in the tumoral immune microenvironment. Methods: Thus, we used female BALB/c mice that were exposed neonatally to a single dose of BPA. Once sexual maturity was reached, a mammary tumor was induced injecting 4T1 cells in situ. After 25 days of injection, we evaluated endocrine alterations, cytokine expression, tissue alterations denoted by macro and micro metastases in the lung, and metastasis-induced cell infiltration. Results: BPA neonatal treatment did not show significant endocrine alterations. Nevertheless, BPA induced a great rate of metastasis to the lung associated with higher intratumoral expression of IL-1b, IL-6, IFN-g, TNF-a and VEGF. Conclusions Our data suggest that cytokines are key players in BC metastasis induction, and that BPA is a risk factor to be considered. This knowledge must be considered with the aim of recognizing environmental pollution in the clinical history of patients to possibly counter BC metastases.

Asphalt cement will not last for a long time as the world encounters a diminishment in the crude oil. For sustainable, flexible pavement development, new resources can provide a contribution to replace it partially or entirely. In this study, asphalt was partially and entirely replaced by guayule resin as a bioresource by-product, extracted during the guayule natural rubber production. Crumb rubber modifier (CRM) was used as an asphalt enhancer. The Superpave grading system was followed at high, intermediate, and low temperatures to evaluate such innovative binder for rutting, fatigue, and thermal cracking, respectively, in addition to viscosity. Therefore, the original, short-term aging and long-term aging were simulated using tank, rolling thin film oven, and pressure aging vessel materials. Additionally, component analysis using Fourier-transform infrared spectroscopy was provided to link the rheological properties with the chemical changes. Outcomes showed a relatively much lower viscosity of guayule in the same high-temperature asphalt grade indicating savings in plant energy consumption and reduced environmental emissions. CRM enhanced guayule, but not as much as asphalt, proven by polymeric component migration through liquid binder. This enhancement was reflected in the rheological performance besides other factors. As-received guayule seems to have high oxygen content proven by strong absorption peak intensities of oxidative bonds (e.g., Carbonyl and sulfoxide). Such pre-oxidation was negatively reflected in the intermediate- and low-temperature performance of guayule and guayule-based binders. However, the investigated guayule had potential to compensate for asphalt replacement in the presence of CRM by 23–42% by weight of blend.

The cardioprotective effects of volatile anesthetics versus total intravenous anesthesia (TIVA) are controversial, especially in patients undergoing non-cardiac surgery. Using current generation high-sensitivity cardiac troponin (hs-cTn), we aimed to evaluate the effect of anesthetics on the occurrence of myocardial injury after non-cardiac surgery (MINS). From February 2010 to December 2016, 3555 patients without preoperative hs-cTn elevation underwent non-cardiac surgery under general anesthesia. Patients were grouped according to anesthetic agent; 659 patients were classified into a propofol-remifentanil total intravenous anesthesia (TIVA) group, and 2896 patients were classified into into a volatile group. To balance the use of remifentanil between groups, a balanced group (n=1622) was generated with patients who received remifentanil infusion in the volatile group, and two separate comparisons were performed (TIVA vs. volatile and TIVA vs. balanced). The primary outcome was occurrence of MINS, defined as rise of hs-cTn I ≥ 0.04 ng/mL within postoperative 48 hours. The secondary outcomes were 30-day mortality, postoperative acute kidney injury (AKI), and adverse events during hospital stay (mortality, type I myocardial infarction (MI), and new-onset arrhythmia). In propensity-matched analyses, the occurrence of MINS was lower in the TIVA group compared to the volatile group (OR 0.642; 95% CI 0.450-0.914; p = 0.014). However, after balancing the use of remifentanil, there was no difference between groups in the risk of MINS (OR 0.832; 95% CI 0.554-1.251; p-value = 0.377). There were no significant associations between the two groups in type 1 MI, new-onset atrial fibrillation, in-hospital and 30-day mortality before and after balancing the use of remifentanil. However, the incidence of postoperative AKI was lower in the TIVA group (OR 0.362; 95% CI 0.194-0.675; p-value = 0.001). After balancing the use of remifentanil, volatile anesthesia and TIVA showed comparable effects on MINS in patients undergoing non-cardiac surgery without preoperative myocardial injury. Further studies are needed on the benefit of remifentanil infusion.

Lung cancer remains the leading cancer killer worldwide. Early diagnosis can effectively increase the patient cure rate but existing diagnostic methods limit early lung cancer diagnosis. Therefore, development of a simple but efficient lung cancer screening method is important to improvement of both the diagnosis rate and the survival rate of lung cancer patients. In this study, ten photosensitive materials with high sensitivity and high specificity were screened accurately to construct a microarray sensor that can rapidly identify six types of lung cancer biomarkers in exhaled breath. Results from hierarchical cluster analysis (HCA), principal component analysis (PCA) and difference maps showed that the classification of the analytes agreed with structure similarity laws. The detection results from parallel experiments and structurally similar analytes, in turn, cluster into a group; the fingerprints of the different analytes have specific response regions. The well-screened sensor chip fabrication workload and cost were both reduced by approximately two thirds, while the microfluidic device sensitivity and stability increased by approximately 1.3 times their corresponding values before optimization. The dual-channel device also offers real-time contrast detection and synchronous parallel detection functions and has potential application prospects for use in extensive screening of high-risk populations for lung cancer.

Opuntia ficus-indica has always interacted with many phytophagous insects at its center of origin; two of them are Dactylopius coccus and D. opuntiae. D. coccus, or true cochineal, is produced to extract carminic acid, and D. opuntiae or wild cochineal is a key invasive pest of O. ficus-indica in more than 20 countries around the world. Despite the economic and environmental relevance of this cactus and, D. opuntiae and D. coccus, there are few studies that have explored volatile organic compounds (VOCs) derived from the plant-insect interaction. The aim of this work was to determine VOCs of D. coccus and D. opuntiae feeding on cultivars suitable for their development and to identify different VOCs in cladodes infested by each Dactylopius species. Volatiles were identified through their essential oils, which were obtained by hydrodistillation. A total of 66 VOCs from both Dactylopius species were identified, and 125 from the Esmeralda and Rojo Pelón cultivars infested by D. coccus and D. opuntiae, respectively, were determined. Differential VOCs production due to infestation by each Dactylopius species was also found. Some changes in methyl salicylate, terpenes such as linalool or the alcohol p-vinylguaiacol were related to Dactylopius feeding on cladodes of their respective cultivars. Changes in these VOCs and their probable role in plant defense mechanisms should receive more attention because this knowledge could improve D. coccus rearing, or to its inclusion in breeding programs for D. opuntiae control in regions where it is a key pest of O. ficus-indica.

Scientific advancements in the food industry have resulted in the discovery of natural substances that can serve various functions in food. Essential oils, in particular, can act as food preservatives or flavoring agents due to their abundance of natural antioxidants, which possess preservative properties. In this study, the composition of Thymus vulgaris essential oil was determined using GC-MS and HS-SPME. The essential oil obtained from Thymus vulgaris L. through hydro-distillation yielded approximately 4%. GC/MS analysis of the essential oil identified 11 components, with a predominant presence of oxygenated monoterpenes (56.97%). Notably, carvacrol (37.63%) and thymol (17.35%) were present in significant amounts, accounting for 54.98% of the overall composition. The in vitro antioxidant activity of the essential oil was evaluated using three methods. The DPPH free radical scavenging test yielded an IC50 of 0.51±0.11 mg mL-1. The β-carotene/linoleic acid bleaching test resulted in an IC50 of 2.58±0.10 mg mL-1. Finally, the ABTS assay indicated relatively lower antioxidant activity compared to ascorbic acid.

A compositional data vector is a special type of multivariate observation in which the elements of the vector are non-negative and sum to a constant, usually taken to be unity. A compositional data does not have zero and only retains relative information. Furthermore, comparisons can only be made between compositional data of the same component. The relevant sample space is the standard simplex. A simplex space is a space that is a generalized form of a triangle. For compositional data, many of the operations defined in Euclidean space are meaningless. Microbiome analyzes have become popular in recent years. Operational Taxonomic Units (OTU) and Amplicon Sequence Variants (ASVs) used in microbiome analysis are one type of compositional data. The microbiome data are counts of different species within a sample and it is compositional. Although there is an order of bacterial abundance within a sample, there is no order of bacterial abundance between samples. Firmicutes and Bacteroidetes, the major phyla in the colon, have been observed in humans worldwide. Gut microbiome analyses often use the Firmicutes/Bacteroidetes ratio and principal coordinates analysis (PCoA). Alpha and beta diversities are used as indicators of bacterial flora diversity. However, misinformation is pervasive in the human microbiome literature and analysis. There is a lot of misunderstanding regarding compositional data and its analysis. An attempt was made to demonstrate how to analyze using the “National Institutes of Biomedical Innovation, Health and Nutrition (NIBIOHN JMD) (Public Data).” The results showed that PCoA did not work, and principal component analysis (PCA) was useful for analyzing the gut microbiome relative diversity.

This paper focuses on the application of principal component analysis (PCA) to conduct a source apportionment of atmospheric aerosols from 8 sampling locations along the Marilao-Meycauayan-Obando River System (MMORS). Aerosols were collected on May 2016 during the same time that water samples were collected. Elemental analysis was conducted using a scanning electron microscope coupled with energy dispersive x-ray (SEM-EDX). Carbon (C), nitrogen (N), oxygen (O), sodium (Na), magnesium (Mg), aluminum (Al), silicon (Si), sulfur (S), chlorine (Cl), potassium (K), calcium (Ca), titanium (Ti), manganese (Mn), iron (Fe), copper (Cu), zinc (Zn), bromine (Br), niobium (Nb), barium (Ba), mercury (Hg), and lead (Pb) concentrations were measured and used as inputs in Principal Component Analysis (PCA). The aerosol samples showed the presence of heavy metals Pb and Hg, elements that were also detected in trace amounts in the water measurements. Concentrations of heavy metals Fe, Pb, Hg in the aerosols were attributed to industrial sources. However, it was determined that the primary source of aerosols in the area were traffic and crustal emissions (C, N, O, Si, Al, Ca). Thus, control of traffic emissions would be more beneficial in reducing aerosol emissions in Meycauayan.

Frequency, amplitude and phase information of the grid voltage are of great importance in constructing a robust controller structure for grid connected inverter systems. This paper presents a simple and robust approach for the instantaneous estimation of positive and negative sequence voltage components under distorted voltage conditions. A second order generalized integrator (SOGI) is used to filter the distorted voltage and to generate orthogonal voltage components for each of the three phases. These filtered and orthogonal components are used for instantaneous calculation of symmetrical components. The implemented method is frequency adaptive; the method is demonstrated and compared to a conventional phase locked loop (PLL) technique with both MATLAB/Simulink simulations and experiments utilizing the dSPACE ds1103 digital controller.

The increasing concern regarding climate change continues to motivate research in the Arctic. Within the delicate cycle of the cryosphere, leads are an important kinematic feature that regulate heat balances in the Arctic. Therefore, it is necessary to quantify the genesis of leads over time to identify when and where changes are occurring. The use of a principal component analysis (PCA) is one such tool that is used to identify the characteristics of seasonal ice variability. The PCA not only identifies “normal” or “dominant” conditions or features, but also extract anomalous spatial features from an archive of long-term sequence of images.

: In this article, the authors propose an algorithmic approach to building a model of the dynamics of economic and, in particular, innovation processes. The approach under consideration is based on a complex algorithm that includes (1) decomposition of the time series into components using singular spectrum analysis; (2) recognition of the optimal component model based on fuzzy rules, and (3) creation of statistical models of individual components with their combination. It is shown that this approach corresponds to the high uncertainty characteristic of the tasks of the dynamics of innovation processes. The proposed algorithm makes it possible to create effective models that can be used both for analysis and for predicting the future states of the processes under study. The advantage of this algorithm is the possibility to expand the base of rules and components used for modeling. This is an important condition for improving the algorithm and its applicability for solving a wide range of problems.