Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

A large diversity of epigenetic factors, such as microRNAs and histones modifications, are known to be capable of regulating gene expression without altering DNA sequence itself. In particular, miR-1 is considered the first essential microRNA in cardiac development. In this study, miR-1 potential role in early cardiac chamber differentiation is analyzed through specific signaling pathways. For this, we performed in chick embryos functional experiments by means of miR-1 microinjections into the posterior cardiac precursors -of both primitive endocardial tubes- committed to sinoatrial region fates. Subsequently, embryos were subjected to whole mount in situ hybridization, immunohistochemistry and RT-qPCR analysis. As a relevant nov-elty, our results revealed that miR-1 increases Tbx5, Gata4 and AMHC1, while this microRNA diminishes Mef2c expression, during early differentiation of cardiac sinoatrial region. Further-more, we observed in this developmental context that miR-1 upregulates CRABPII and RARß, and downregulates CRABPI, which are three crucial factors in retinoic acid signaling pathway. Interestingly, we also noticed that miR-1 directly interacts with HDAC4 and Calmodulin, as well as with Erk2/MAPK1, which are three key factors actively involved in Mef2c regulation. Our study shows, for the first time, a key role of miR-1 as an epigenetic regulator in early differenti-ation of cardiac sinoatrial region through orchestrating opposite actions between retinoic acid and Mef2c, fundamental to properly assign cardiac cells to their respective heart chambers. A better understanding of those molecular mechanisms modulated by miR-1 will definitely help in fields applied to therapy and cardiac regeneration and repair.

Herein, we present the design technique of a resonant rectifier for piezoelectric (PE) energy harvesting. We propose two diode equivalents to reduce the voltage drop in the rectifier operation, a minuscule-drop-diode equivalent (MDDE) and a low-drop-diode equivalent (LDDE). The diode equivalents are embedded in resonant rectifier integrated circuits (ICs), which use symmetric bias-flip to reduce the power wasted for charging and discharging the internal capacitance of a PE transducer. The self-startup function is supported by synchronously generating control pulses for the bias-flip from the PE transducer. Two resonant rectifier ICs, using both MDDE and LDDE, are fabricated in a 0.18 μm CMOS process and their performances are characterized under external and self-power conditions. Under the external-power condition, the rectifier using LDDE delivers an output power POUT of 564 μW and a rectifier output voltage VRECT of 3.36 V with a power conversion efficiency (PCE) of 90.1%. Under self-power conditions, the rectifier using MDDE delivers a POUT of 288 μW and a VRECT of 2.4 V with a corresponding PCE of 74.6%. The result shows that the power extraction capability of the proposed rectifier is 5.9 and 3.0 times higher than that of a conventional full-bridge rectifier.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

Natural polluted insulator surfaces are always coated with various kinds of soluble constituents, and those constituents affect flashover performance differentially. Currently this fact is not considered either in laboratory experiments or field pollution degree measurements, causing the existing insulation selection method to be deficient. In this paper a systematical research on insulator flashover voltage gradient correction involving types of soluble pollution constituents was presented. Taking typical type glass insulator as the sample, its flashover tests polluted by typical soluble chemicals NaCl, NaNO₃, KNO₃, NH₄NO₃, MgSO₄, Ca(NO₃)₂ and CaSO₄ were carried out. Then the flashover gradient correction was made combining the flashover performance of each soluble constituent, the ESDD contribution of the seven constituents, as well as the saturation performance of CaSO₄. The correction was well verified with the flashover test results of insulator polluted by three types of soluble mixture. Research results indicate that the flashover gradient correction method proposed by this paper performs well in reducing the calculating error. It is recommended to carry out component measurements and flashover gradient correction to better select outdoor insulation configuration.

A power factor correction (PFC) rectifier is compulsory for any electronic circuitry connected to the electrical grid. The majority of PFCs that are utilized are based on a step-up converter that supplies high DC voltage at its output terminal. Electric vehicle battery voltage varies from a few hundred to almost a thousand volts. Thus, an additional conversion step is obligatory when designing an all-brand universal charger. This paper presents a new type of front-end versatile step up / down three voltage level PFC. The rectifier can operate in continuous conduction mode or discontinuous conduction mode. First, the rectifier’s principle of operation is described, and then an innovative rectifier is analyzed for continuous and discontinuous conduction modes. Finally, the proposed theory is experimentally validated in a multiplier-less dual loop mode at discontinuous conduction modes. It was shown that although there is no multiplier use in the control circuitry, the power factor is near unity. It was revealed that the rectifier could swing the output voltage from 50 V to 900 V while the input voltage was 230 Vrms. The innovative topology suits any standard PFC rectifier, three-level voltage supplement, and dual-stage low-voltage power supply.

Abstract: Building Information Modelling (BIM) methodology has been empowering the quality of the construction activity in all sectors: multidisciplinary designs development; construction planning and monitoring; building management and maintenance. A BIM environment aggre-gates several disciplines and different professional skillsets and in order to control and improve the quality of a BIM project, a BIM manager is required. The BIM manager has the responsibility to coordinate all tasks involved in a building design and associated activities usually workout over the project documents. This professional can access to the distinct discipline models, located in a shared platform, and request for amendments if inconsistencies are detected. The topic of the present study is illustrated with three building cases were distinct specific projects, disciplines and tasks were elaborated: collaboration between disciplines (architecture, structures and con-struction); structural analyses and reinforcement details; quantity take-off of materials and cost estimation; construction scheduling and simulation. Although there are still limitations in the implementation of BIM methodology in all sectors and stages, within the construction industry, BIM has been bringing an important improvement in the quality of a building design, reflected in the quality of the final product. The present study put in evidence the BIM manager role in pro-jects that aggregates several disciplines and experts, bringing an important contribution in the quality of a building design. BIM methodology is a current demand in the construction industry supported on advanced technology and in an adequate management of projects.

Accurate forecasting of icing thickness has a great significance for ensuring the security and stability of power grid. In order to improve the forecasting accuracy, this paper proposes an icing forecasting system based on fireworks algorithm and weighted least square support vector machine (W-LSSVM). The method of fireworks algorithm is employed to select the proper input features with the purpose of eliminating the redundant influence. In addition, the aim of W-LSSVM model is to train and test the historical data-set with the selected features. The capability of this proposed icing forecasting model and framework is tested through the simulation experiments using real-world icing data from monitoring center of key laboratory of anti-ice disaster, Hunan, South China. The results show that the proposed W-LSSVM-FA method has a higher prediction accuracy and it may be a promising alternative for icing thickness forecasting.

With the development of higher voltage power grid, the high and low voltage parallel loops are emerging, which lead to energy losses, even threaten the security and stability of power system. The multi-infeed HVDC configurations widely appearing in AC/DC interconnected power system make this situation even worse. Aimed at energy saving and system security, a decision optimization method for power grid operating condition with high and low voltage parallel loops is proposed in this paper. Firstly, considering hub substation distribution and power grid structure, parallel loop opening schemes are generated with GN algorithm. Then, candidate opening schemes are preliminarily selected from all these generated schemes based on a filtering index. Finally, with the influence on power system security, stability and operation economy in consideration, an evaluation model for candidate opening schemes is founded based on analytic hierarchy process (AHP). And a fuzzy evaluation algorithm is used to find the optimal scheme. Simulation results of New England 39-bus system and an actual power system validate the effectiveness and superiority of this proposed method.

Day by day, the share of renewable energy-based power plants such as offshore wind farms and photovoltaic power plants, in the present-day power systems is escalating. Nevertheless, most of these power-producing facilities have been located quite far away from the load centers. At this stage, HVDC power systems provide satisfactory options due to qualities such as reduced line losses, substantial controllability, and environmental advantages. Nevertheless, unique converter designs are required to combine asynchronous HVDC networks with each other and with already existing high voltage alternating current (HVAC) networks. In this study, based on the above special cases, a unique DC-DC modular multilevel converter (MMC) architecture is presented that provides an excellent solution for both integrating modern asynchronous HVDC networks and integrating these modern HVDC power systems with existing asynchronous HVAC power systems. The mathematical analysis of the recommended DC-DC MMC design has been examined in detail and the power transfer between two asynchronous power grids has been realized in a simulation environment. Efficient bilateral power transmission has been made achievable by the control system. The recommended DC-DC MMC topology has shown to be a highly successful approach, in the interconnection of HVDC power systems, according to the simulation results.

Among the major systems of high-speed rail, the arch network relationship, wheel-rail relationship and fluid-structure coupling relationship are important links affecting the performance of high-speed rail, and also the main control factors affecting the speed limit of high-speed rail. From this perspective, the contact state and interactive relationship between pantograph and catenary are the key factors affecting the forward performance of high-speed rail. As a key component in the pantograph system, the actuator is responsible for adjusting the contact force and position between the pantograph and the contact line. The performance characteristics of the actuator, such as response speed, accuracy, stability and durability, directly affect the control performance of the whole pantograph system. In this paper, the research status of the active control technology of high-speed railway pantograph is reviewed, and the future development direction is pointed out, which provides a new idea for the development of pantograph technology.

Tumor microenvironment (TME) is composed of various cellular components such as tumor cells, stromal cells including fibroblasts, adipocytes, mast cell, lymphatic vascular cells and infiltrating immune cells, macrophages, dendritic cells and lymphocytes. The intricate interplay between these cells influences tumor growth, metastasis and therapy failure. Significant advancements in breast cancer therapy have resulted in a substantial decrease in mortality. However, existing cancer treatments frequently result in toxicity and nonspecific side effects. Therefore, improving targeted drug delivery and increasing the efficacy of drugs are crucial for enhancing the treatment outcome and reducing the burden of toxicity. In this review, we provided an overview of how tumor and stroma-derived osteopontin (OPN) plays a key role in regulating the oncogenic potential of various cancers including breast. Next, we have dissected the signalling network by which OPN regulates tumor progression through interaction with selective integrins and CD44 receptors. This review addresses the latest advancement in role of various splice variants of OPN in cancer progression and OPN-mediated tumor-stromal interaction, EMT, CSCs enhancement, immunomodulation, metastasis, chemoresistance, metabolic reprogramming and further suggest that OPN might be a potential therapeutic target and prognostic biomarker for the evolving landscape of cancer management.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

Sperm cells must undergo a complex maturation process after ejaculation to be able to fertilize an egg. One component of this maturation is hyperpolarization of the membrane potential to a more negative value. The ion channel responsible for this hyperpolarization, SLO3, was first cloned in 1998, and since then much progress has been made to determine how the channel is regulated and how its function intertwines with various signaling pathways involved in sperm maturation. Although SLO3 was originally thought to be present only in the sperm of mammals, recent evidence suggests that a primordial form of the gene is more widely expressed in some fish species. As with many reproductive genes, SLO3 is rapidly evolving with low conservation between closely related species and different regulatory and pharmacological profiles. Despite these differences, SLO3 appears to have a conserved role in regulating sperm membrane potential and driving large changes in response to stimuli. As with the differences in regulation of the channel, the effect of this hyperpolarization of the membrane potential may vary among mammalian species. Recent discoveries have elucidated the role of SLO3 in these processes in human sperm and provided tools to target the channel to affect human fertility.

This work presents a control scheme to control the grid-connected single-phase photovoltaic (PV) system. The considered system has four 250W solar panels, a non-inverting buck-boost DC-DC converter, and DC-AC inverter with LCL filter. The control system aims to track and operate at the maximum power point (MPP) of PV panels, regulate the voltage of DC link, and supply the grid with a unity power factor. To well achieve these goals, the proposed control system consists of three parts, that are MPP tracking controller module with a fuzzy-based modified incremental conductance (INC) algorithm, a DC-link voltage regulator with a hybrid fuzzy proportional-integral (PI) controller, and a Current Controller module using the linear quadratic regulator (LQR) for grid-connected power. Based on fuzzy control and LQR, this work introduces a full control solution for grid-connected single-phase PV systems. The key novelty of this research is to analyze and prove that the newly proposed method is more successful in numerous aspects by comparing and evaluating the previous and present control methods. The designed control system settles quickly, which is critical for output stability. In addition, as compared to backstepping approach used in our past study, the LQR technique is more resistant to sudden changes and disturbances. Furthermore, backstepping method produces the larger overshoot, which has a detrimental impact on efficiency. Simulation findings under various weather conditions were compared to theoretical ones to indicate that the system can deal with variations in weather parameters.

With the widespread use of new equipment such as distributed photovoltaics, distributed energy storage, electric vehicles, and distributed wind power, the control of low-voltage distribution networks (LVDNs) has become increasingly complex. Acquiring the most recent topological structure is essential for conducting accurate analysis and real-time control of LVDNs. The signal-injection-based topology identification algorithm is favored for its speed and efficiency. This study proposes a new signal-injection-based topology identification algorithm aimed at solving the issues of reduced completeness and correctness of identification caused by missing feature signal records (FSRs). By analyzing the correlations between FSRs of different positions, the algorithm employs vertical and horizontal completion methods to effectively address missing data, combined with inclusion detection algorithms, to identify the topology of LVDNs. Based on the study of actual LVDN data, the results indicate that the algorithm not only significantly improves the completeness and correctness of topology identification for LVDNs but can also increase the number of devices in operation by evaluating the status of topological equipment, further enhancing the topology identification performance.

Among the plant nutrients potassium (K) is one of the vital elements required for plant growth and physiology. Potassium is not only a constituent of plant structure but also plays regulatory function in several biochemical processes related to protein synthesis, carbohydrate metabolism, enzyme activation. There are several physiological processes like stomatal regulation and photosynthesis are dependent on K. In the recent decades K was found to provide abiotic stress tolerance. Under salt stress, K helps in maintaining ion homeostasis and regulation of osmotic balance. Under drought stress condition K regulates the stomatal opening and makes the plants adaptive to water deficit. Many reports provided the notion that K enhances the antioxidant defense in plants and therefore, protects the plants from oxidative stress under various environmental adversities. Also, it provides some cellular signaling alone or in association with other signaling molecules and phytohormones. Although a considerable progress in understanding K-induced abiotic stress tolerance in plants has been achieved the exact molecular mechanisms of such protections are still under research. In this review, we summarized the recent literature on the biological functions of K, its uptake, and translocation and its role in plant abiotic stress tolerance.

Voltage Stability & Control, is very crucial compared to other Power System (PS) Quality and Stability issues. Long-Vertical-Power-Flows in Conventional Grids, causes voltage drops which in turn causes huge power losses, especially in the Medium Voltage (MV) and Low Voltage (LV) Distribution Networks. Such technical losses in abysmally-planned weak distribution networks, lead to substantial loss of revenues to the utility grid. Apart from classic Voltage Regulation (VR) techniques, with the rise of Distributed Generation (DG) based on Renewable Energy Sources (RES), Horizontal-Power-Flows can be introduced in the network, through various Smart Grid techniques. Coupling such sources, near load centers shall mitigate long flows from expensive conventional sources at times of huge demands, improving feeders’ Voltage Profile. This Ancillary Service of Voltage Support from DG RESs shall thereby alleviate revenue losses caused by long-power-flows in weak distribution grids. For a developing country like Pakistan, loss of revenue from an already expensive utility gives huge blow to the economy. So, a similar technique for voltage support is proposed for an 11-kV feeder, which faces similar problem, and the results are remarkable. The technique is implemented using OpenDSS Tool by modelling 3MWp PV Penetration along with some future storage.

Endothelial function is regulated by a myriad of complex pathways. In our previous study, the expression of miR-378a-3p was shown to inhibit endothelial autophagy and impair endothelial function. However, the mechanism underlying the effect of miR-378a-3p in endothelial cells remains to be elucidated. By employing an in silico approach, Protein Disulfide Isomerase 4 (PDIA-4) was identified as a target of miR-378-3p; however, its’ role in endothelial cells is not known. We here report that endothelial cell-specific loss of PDIA-4 leads to impaired autophagic flux accompanied by loss of endothelial function and apoptosis. Endothelial cell-specific loss of PDIA-4 also induced marked changes in endothelial cells’ architecture, accompanied with the loss of endothelial markers and gain of mesenchymal markers consistent with endothelial-to-mesenchymal transition (EndMT). Loss of PDIA-4 activates TGF-signaling, and inhibition of TGF-signaling inhibits EndMT in PDIA-4 silenced endothelial cells in vitro. Our findings help elucidate the role of PDIA-4 in endothelial autophagy and endothelial function and provide a potential target to modulate and/or limit autophagy and EndMT in (patho-)physiological conditions.

The formation of the required AC voltage level is currently one of the most important problems. An unstable voltage level can lead to the failure of domestic and industrial equipment, also to the appearance of a lighting equipment flicker effect, which can adversely affect the operating mode. In this regard, the development of AC voltage regulators that perform the function of stabilizers has become relevant. In turn, new topologies should be energy efficient and reliable, this can be achieved by reducing the number of semiconductor elements, which in turn will reduce losses and increase efficiency. In addition to voltage stabilization, AC voltage regulators have found application as soft-start devices for asynchronous motors, and have become competitors to frequency converters. The power level can vary from units to tens of kilowatts where such devices can be used. This paper provides a review of AC voltage regulators, which can be used both as soft starters and AC voltage stabilizers. The analysis of the circuits was carried out and the efficiency was evaluated through their total harmonic distortions (THD), power factor and efficiency coefficient. Experiments were also performed for a number of circuits, where their operating modes were evaluated. Eventually, all circuits were divided into full number of switches with two or more AC switches per phase, with a reduced number of switches, where one AC switch per phase and with low number of switches – with one complementary pair of AC switches for all three phases.

In recent years, nonalcoholic fatty liver disease/steatohepatitis (NAFLD/NASH) has become a leading worldwide disease, and its therapies are facing many complexities. Peroxisome proliferator-activated receptors (PPARs) are ligand-activated transcription factors that belong to the nuclear receptor (NR) superfamily and have three subtypes: PPARα (NR1C1), PPARβ/δ (NR1C2), and PPARγ (NR1C3). They have been identified to be essential in the regulation of lipid metabolism by controlling the transcription of genes related to fatty acids, bile acids, and cholesterol metabolism. Many PPAR agonists have been reported, such as natural agonists (fatty acids, eicosanoids, and phospholipids) and synthetic ligands (fibrates, thiazolidinediones, glitazars, and elafibranor). PPAR-based chemicals have a breakthrough in the innovation of therapy for fatty liver disease. This review will provide an overview of how PPARα and PPARγ play roles in lipid homeostasis, discussing the consideration of their agonists as potential therapeutic agents for NAFLD/NASH.

Understanding the biology underlying the mechanisms and pathways regulating pancreatic β-cell development is necessary to understand the pathology of diabetes mellitus (DM), which is characterized by the progressive reduction in insulin producing β-cell mass. Pluripotent stem cells (PSCs) can potentially offer an unlimited supply of functional β-cells for cellular therapy and disease modeling of DM. Homeobox protein NKX6.1 is a transcription factor (TF) that plays a critical role in pancreatic β-cell function and proliferation. In human pancreatic islet, NKX6.1 expression is exclusive toβ-cells and is undetectable in other islet cells. Several reports showed that activation of NKX6.1 in PSC-derived pancreatic progenitors (MPCs), expressing PDX1 (PDX1⁺/NKX6.1⁺), warrants their future commitment to monohormonal β-cells. However, further differentiation of MPCs lacking NKX6.1 expression (PDX1⁺/NKX6.1^-) results in an undesirable generation of non-functional polyhormonal β-cells. The importance of NKX6.1 as a crucial regulator in MPC specification into functional β-cells directs attentions to further investigating its mechanism and enhancing NKX6.1 expression as a mean to increase β-cell function and mass. Here, we shed light on the role of NKX6.1 during pancreatic β-cell development and in directing the MPCs to functional monohormonal lineage. Furthermore, we address the transcriptional mechanisms and targets of NKX6.1 as well as its association with diabetes.

The outer membrane of Gram-negative bacteria contains a variety of pore-forming structures collectively referred to as porins. Some of these are voltage-dependent, but weakly so, closing at high voltages. Triplin, a novel bacterial pore-former, is a three-pore structure, highly voltage dependent, with a complex gating process. The three pores close sequentially: pore 1 at positive potentials, 2 at negative and 3 at positive. A positive domain containing 14 positive charges (the voltage sensor) translocates through the membrane during the closing process and the translocation is proposed to take place by the domain entering the pore and thus blocking it resulting in the closed conformation. This mechanism of pore closure is supported by kinetic measurements that show that in the closing process the voltage sensor travels through most of the transmembrane voltage before reaching the energy barrier. Voltage-dependent blockage of the pores by polyarginine but not by a 500 fold higher concentrations of polylysine, is consistent with the model of pore closure, with the sensor consisting mainly of arginine residues, and with the presence, in each pore, of a complementary surface that serves as a binding site for the sensor.

In this paper, we discuss voltage control method for buck converter operating in continuous conduction mode (CCM) using analog feedback system. The aim of this work is to control the output voltage of a buck converter during the variation in load current. This is obtained using analog feedback made with operational amplifier (Opamp). However, the same technique can be applied to other DC-DC converters (e.g boost, buck-boost, cuk converter, etc) in CCM mode, but for the purpose of analysis buck converter is chosen as an example.

Nowadays, in low voltage (LV) electric distribution networks (EDNs), the Distribution Network Operators (DNOs) are encountering a high number of connected small-scale distributed generation units, mainly photovoltaic (PV) prosumers. The irregular behavior of the prosumers, together with the uncertainty degree of the requested and injected powers associated with all end-users from the LV EDN, can cause voltage variations with violations of the allowable limits. In this context, the paper developed an efficient and resilient expert system integrating the rule-based reasoning applied to the On-load Tap Changer (OLTC)-fitted transformer to improve the efficiency of the voltage control in the PV-rich LV EDNs. An in-depth analysis based on 75 scenarios, resulting from the combinations of three indicators: the penetration degree of the PV prosumers, consumption evolution associated with the consumers, and energy production of the PV systems, has been performed to demonstrate the efficiency of the proposed expert system in an LV EDN from a rural area belonging to a Romanian DNO. The success rate of the expert system has been 86.7% (65 out of 75 scenarios didn't have voltage issues, all values being between the allowable limits in 100% of the time slots associated with the analyzed period). For the other scenarios (representing 13.3%), the values have been inside the range [-10%, +10%] at least 95% of the time slots, according to the European Power Quality Standard, and for the rest of the time slots up to 100% being very close to the upper and lower limits of the range, with highly mitigating of the voltage variations.

The enzyme-coupled transient receptor potential channel subfamily M member 7, TRPM7, has been associated with immunity and immune cell signalling. Here, we review the role of this remarkable signalling protein in lymphocyte proliferation, differentiation, activation and survival. We also discuss its role in mast cell, neutrophil and macrophage function and highlight the potential of TRPM7 to regulate immune system homeostasis. Further, we shed light on how the cellular signalling cascades involving TRPM7 channel and/or kinase activity culminate in pathologies as diverse as allergic hypersensitivity, arterial thrombosis, and graft versus host disease (GVHD), stressing the need for TRPM7 specific pharmacological modulators.

Understanding pollen and ovule fertility as factors influencing fruit and seed set is important in cassava breeding. Red light (RL) and plant growth regulators (PGRs) have been used to induce or enhance flowering and fruit set in cassava without any reference to effects on pollen viability or ovule fertilizability. This study investigated effects of field-applied RL and PGR on pollen viability and ovule fertilizability. Panels of cassava genotypes, with early or moderate flowering responses were used. RL was administered from dusk to dawn. Two PGRs, a cytokinin (6-benzyl adenine, BA) and an anti‑ethylene (silver thiosulphate, STS) were applied. Pollen viability was assessed basing on pollen grain diameter, in vitro stainability, in vivo germinability, ovule fertilizability and ploidy level. Treating flowers with RL led to increased pollen diameter from 143.6 to 148.5µm, stainability from 82.9 to 93.0%, ovule fertilizability from 52.0 to 56.9% in treated female flowers and 47.7 to 64.3% on using pollen from treated male flowers. Fruit set increased from 51.5 to 71.8% in RL-treated female flowers and from 53.7 to 71.1% when pollen from RL-treated male flowers was used. Seed set followed a trend similar to that of fruit set. Ploidy level of pollen from RL-treated flowers increased slightly and positively correlated with pollen diameter (R2 = 0.09*), ovule fertilization (R2 = 0.20*), fruit (R2 = 0.59*) and seed set (R2 = 0.60*); but negatively correlated with pollen stainability. Treating flowers with PGR did not affect pollen diameter and stainability, but increased ovule fertilizability from 42.9 to 64.9% and fruit set from 23.2 to 51.9% in treated female flowers and 31.3 to 54.7% when pollen from treated male flowers was used. Application of combined BA+STS on male flowers caused the highest ovule fertilizability, fruit and seed set efficiency, though this varied among study genotypes. These results show that RL and PGR treatment of flowers increases pollen viability and ovule fertilizability. This is important for planning pollination strategies in cassava breeding programmes.

Besides the increase in global energy demand, access to clean energy, reduction in greenhouse gas emissions caused by conventional power generation sources, energy security, and availability of electricity in remote villages in emerging nations are some of the factors that foster the use of renewable energy sources (RESs) in generating electricity. One of the aims of initiating microgrids (MGs) is to maximize the benefits of RES and alleviate the associated grid integration issues. Microgrids are made up of RES connected to electrical loads within clearly delineated electrical limits that operate as individual controllable units on the electrical network. It can operate in-dependently as well as in connection with the grid. The paper presents an overview of microgrids and investigates the system's performance when connected to and disconnected from the grid. Furthermore, in both modes of operation, the functioning and behavior of system components such as the bidirectional DC-DC converter and energy storage system (ESS) were evaluated. The architecture of the proposed microgrid consists of a small hydropower plant, a wind farm, and a battery energy storage system (BESS). The microgrid under investigation is modeled and simu-lated using MATLAB and Simulink.

Psychiatric disorders are mental, behavioral or emotional disorders. These conditions are prevalent, one in four adults suffer from any type of psychiatric disorders world-wide. It has always been observed that psychiatric disorders have a genetic component, however new methods to sequence full genomes of large cohorts have identified with high precision genetic risk loci for these conditions. Psychiatric disorders include, but are not limited to, bipolar disorder, schizophrenia, autism spectrum disorder, anxiety disorders, major depressive disorder, and attention-deficit and hyperactivity disorder. Several risk loci for psychiatric disorders fall within genes that encode for voltage-gated calcium channels (Ca_Vs). Calcium entering through Ca_Vs is key for multiple neuronal processes. In this review, we will summarize recent findings that link Ca_Vs and their auxiliary subunits to psychiatric disorders. First, we will provide a general overview of Ca_Vs structure, classification, function, expression and pharmacology. Next, we will summarize tools and databases to study risk loci associated with psychiatric disorders. We will examine functional studies of risk variations in Ca_V genes when available. We will review pharmacological evidence of the use of Ca_V modulators to treat psychiatric disorders. Our review will be of interest for those studying pathophysiological aspects of Ca_Vs.

The symbiotic interaction between leguminous and Bradyrhizobium sp. SUTN9-2 mainly relies on the nodulation process through Nod factors (NFs), while the type IV secretion system (T4SS) acts as an alternative pathway in this symbiosis. Two copies of T4SS (T4SS1 and T4SS2) are located on the chromosome of SUTN9-2. ΔT4SS1 reduces both nodule number and nitrogenase activity in all SUTN9-2 nodulating legumes. The functions of three selected genes (copG1, traG1, and virD21) within the region of the T4SS1 were examined. We generated deleted mutants and tested in Vigna radiata cv. SUT4. ΔtraG1 and ΔvirD21 exhibited lower invasion efficiency at the early stages of root infection but could be lately restored. In contrast, ΔcopG1 completely hindered nodule organogenesis and nitrogenase activity in all tested legumes. ΔcopG1 showed low expression of nodulation gene and ttsI, but exhibited high expression levels of T4SS genes, traG1 and trbE1. The secreted proteins from ΔT4SS1 were down-regulated compared to the wild type. Although ΔcopG1 secreted several proteins after flavonoid induction, T3SS (nopP and nopX) and C4-dicarboxylate transporter (dct) were not detected. These results confirm the crucial role of the copG1 gene as a novel key regulator in the symbiotic relationship between SUTN9-2 and legumes.

This work presents an alternative to harnessing wind energy with an Electromagnetic Frequency Regulator (EFR) coupled to a hydrostatic transmission and associated with a horizontal axis wind turbine, a bidirectional frequency inverter and a secondary energy source, in a hybridized system. The hydrostatic transmision is composed by a fixed displacement axial piston pump and a variable displacement, swash plate, axial piston motor. Feedback linearization was used as a technique to control the motor geometric displacement, and a prediction algorithm for the steady state rotations of the armature and the electromagnetic field has been developed. A 5\,kW project was simulated on a Scilab platform, with combinations of constant or variable load, and constant or variable wind speed. The results indicated that the system was able to supply the generator load, adapting to fluctuations in wind speed. The possibility of storing wind energy through the inverter has also been proven. The system can accumulate energy in batteries during the fastest wind regimes, to use it when the turbine power is lower than the load.

This paper addresses the effects of electric power quality on robotics operation. A general overview is reported to highlight the main characteristics of electric power quality and their effects on a powered system by considering an end-users viewpoint. Then, authors outline the influence of voltage dip effects by focusing at robotic grasping applications. A specific case of study is reported as referring to LARM Hand IV, a three-fingers robotic hand, which has been designed and built at LARM in Cassino. A dedicated test rig has been settled up for generating predefined voltage dips. Experimental tests are carried out for evaluating the effects of different types of voltage dips on the grasping of objects.

Normally, the Nernst voltage calculated from the concentration of the reaction gas in the flow channel is considered to be the ideal voltage (reversible voltage) of the oxyhydrogen fuel cell, but actually it will cause a concentration gradient when the reaction gas flows from the flow channel through the gas diffusion layer to the catalyst layer. The Nernst voltage loss in fuel cells in most of the current literature is thought to be due to the difference in concentration of reaction gas in the flow channel and concentration of reaction gas on the catalyst layer at the time when the high net current density is generated. Based on the Butler-Volmer equation in oxyhydrogen fuel cell, this paper demonstrates that the Nernst voltage loss is caused by the concentration difference of reaction gas in flow channel and on the catalytic layer at the time when equilibrium potential (Galvanic potential) of each electrode is generated.

A balanced chromosomal translocation disrupting DISC1 (Disrupted in Schizophrenia 1) gene has been linked to psychiatric diseases, such as major depression, bipolar disorder and schizophrenia. Since the discovery of this translocation, many studies have focused on understating the role of the truncated isoform of DISC1, hypothesizing that the gain of function of this protein could be behind the neurobiology of mental conditions, but not so many studies have focused in the mechanisms impaired due to its loss of function. For that reason, we perform an analysis on the cellular proteome of primary neurons in which DISC1 was knocked down with the goal of identifying relevant pathways directly affected by DISC1 loss of function. Using an unbiased proteomic approach, we found that the expression of 31 proteins related to neurodevelopment (e.g. CRMP-2, stathmin) and synaptic function (e.g. MUNC-18, NCS-1) is regulated by DISC1 in primary mouse neurons. Hence, this study reinforces the idea that DISC1 is a unifying regulator of both neurodevelopment and synaptic function, thereby providing a link between these two key anatomical and cellular circuitries.

In this paper, modelling designing and simulation of a simple voltage amplidyne system is done using robust control theory. In order to increase the performance of the voltage amplidyne system with H ∞ optimal control synthesis and H ∞ optimal control synthesis via ∞-iteration controllers are used. The open loop response of the voltage amplidyne system shows that the system can amplify the input 7 times. Comparison of the voltage amplidyne system with H ∞ optimal control synthesis and H ∞ optimal control synthesis via ∞-iteration controllers to track a desired step input have been done. Finally, the comparative simulation results prove the effectiveness of the proposed voltage amplidyne system with H ∞ optimal control synthesis controller in improving the percentage overshoot and the settling time.

The NF-κB (nuclear factor K-light-chain-enhancer of activated B cells) transcription factor family is critical for modulating the immune proinflammatory response throughout the body. During the resting state, inactive NF-κB is sequestered by IκB in the cytoplasm. Proteasomal degradation of IκB activates NF-κB, mediating its translocation into the nucleus to act as a nuclear transcription factor in the upregulation of proinflammatory genes. Stimuli that initiate NF-κB activation are diverse, but are canonically attributed to proinflammatory cytokines and chemokines. Downstream effects of NF-κB are cell type specific and, in the majority of cases, result in activation of pro-inflammatory cascades. Acting as the primary immune responders of the central nervous system, microglia exhibit upregulation of NF-κB upon activation in response to pathological conditions. Under such circumstances, microglial crosstalk with other cell types in the central nervous system can induce cell death, further exacerbating the disease pathology. In this review, we will emphasize the role of NF-κB in triggering neuroinflammation mediated by microglia.

Adventitious roots play a crucial role inr the nourishment and propagation of arboreal vegetation. In order to shed light on the physiological and biochemical characteristics of the challenging-to-propagate mulberry tree species, an investigation was conducted. This study aimed to compare the responses of various root morphological indicators, endogenous hormones, and oxidase activities in the "Yueshenda 10" fruit mulberry, at different stages of treatment. The ultimate objective was to identify the factors influencing the process of root development. The findings revealed a distinct '/\' pattern in the levels of IAA and JA within the cuttings. Conversely, the changes in ABA, ZR and GA3 exhibited a '/\/' pattern. The fluctuation of IAA/ABA values followed a '\/\' mode, whereas the IAA / ZR values initially increased, followed by a subsequent decrease. The correlation between the initial concentrations of these five endogenous hormones and the rooting rate displayed variations. Notably, IAA demonstrated the strongest association with the rooting rate, exhibiting a positive correlation with both IAA and ZR. Regarding the activity of three antioxidant enzymes (IAAO, POD and PPO), a '/\' trend was observed, wherein the enzyme activity increased under ABT1 treatment. However, the peak activity levels of the enzymes appeared during different periods: germination, induction, and expression, respectively. Overall, the most effective treatment for promoting root development and significantly enhancing the root growth parameters of mulberry was found to be 800mg/L ABT1. Exogenous hormone treatment expedited the synthesis of antioxidant enzymes, thereby shortening the rooting time and facilitating root formation.

Subversion of programmed cell death-based host defence systems is a prominent feature of infections by large DNA viruses. African swine fever virus (ASFV) is a large DNA virus and sole member of the Asfarviridae family that harbors the B-cell lymphoma 2 or Bcl-2 homolog A179L. A179L has been shown to bind to a range of cell death inducing host proteins including pro-apoptotic Bcl-2 proteins as well as the autophagy regulator Beclin. Here we report the crystal structure of A179L bound to the Beclin BH3 motif. A179L engages Beclin using the same canonical ligand binding groove that is utilized to bind to pro-apoptotic Bcl-2 proteins. The mode of binding of Beclin to A179L mirrors that of Beclin binding to human Bcl-2 and Bcl-xL as well as murine gamma-herpesvirus 68. Introduction of bulky hydrophobic residues into the A179L ligand binding groove via site directed mutagenesis ablates binding of Beclin to A179L, leading to a loss of ability of A179L to modulate autophagosome formation in Vero cells during starvation. Our findings provide a mechanistic understanding for the potent autophagy inhibitory activity of A179L and serve as a platform for more detailed investigations into the role of autophagy during ASFV infection.

Background: RNA helicase DHX15 plays a significant role in vasculature development and lung metastasis in vertebrates. In addition, several studies have demonstrated the overexpression of DHX15 in the context of hepatocellular carcinoma. Therefore, we hypothesized that this helicase may play a significant role in liver regeneration, physiology and pathology. Methods: Dhx15 gene deficiency was generated by CRISPR/Cas9 in zebrafish and by TALEN-RNA in mice. FANA Antisense-Oligonucleotides were used to silence Dhx15 in wild-type mice. The hepatocellular carcinoma tumor induction model was generated by subcutaneous injection of Hepa 1-6 cells. Results: Homozygous Dhx15 gene deficiency was lethal in zebrafish and mouse embryos. Dhx15 gene deficiency impaired liver organogenesis in zebrafish embryos and liver regeneration after partial hepatectomy in mice. Also, heterozygous mice presented decreased number and size of liver metastasis after Hepa 1-6 cells injection compared to wild-type mice. Dhx15 gene silencing with FANA Antisense-Oligonucleotides in wild-type mice resulted in 80% reduced expression in the liver and a significant reduction in other major organs. In addition, Dhx15 gene silencing significantly hindered primary tumor growth in the hepatocellular carcinoma experimental model. Regarding the potential use of DHX15 as a diagnostic marker for liver disease, patients with hepatocellular carcinoma showed increased levels of DHX15 in blood samples compared with subjects without hepatic affectation. Conclusion: Dhx15 is a key regulator of liver physiology and organogenesis, is increased in the blood of cirrhotic and hepatocellular carcinoma patients and has a key role in controlling hepatocellular carcinoma tumor growth and expansion in experimental models.

Timely mitosis is critically important for the early embryo development. It is regulated by the activity of the ubiquitously conserved CDK1 kinase. The dynamics of CDK1 activation must be precisely controlled to assure physiologic and timely entry into mitosis. Recently, a known S-phase regulator CDC6 emerged as a key player in the mitotic CDK1 activation cascade in early embryonic divisions, operating together with Xic1 as a CDK1 inhibitor upstream of the Aurora A- and PLK1 kinases, both CDK1 activators. Herein we review the molecular mechanisms that underlie the control of the mitotic timing, with special emphasis on how CDC6/Xic1 function impacts CDK1 regulatory network. We focus on the presence of two independent mechanisms inhibiting the dynamics of CDK1 activation: Wee1/Myt1- and CDC6/Xic1-dependent, and how they cooperate with CDK1 activating mechanisms. As a result we propose a comprehensive model integrating CDC6/Xic1-dependent inhibition into the CDK1-activation cascade. The physiological dynamics of CDK1 activation appear to be tuned by the system of multiple inhibitors and activators and their integrated modulation ensures concomitantly both the robustness and certain flexibility of the control of this process. Identification of multiplied activators and inhibitors of CDK1 activation upon M-phase entry allows a better understanding of why cells divide at a specific time, and how the pathways involved in the timely regulation of the cell division are all integrated to precisely tune the control of mitotic events.

We communicate the theoretical results in the study of utilizing the quantum phenomena in optical current for quantum computation in the context of high precision voltage measurements. These results can be used around computation by quantum sampling and quantum communication as the basis for further research and physical implementations. We propose a Main Optical Setup (MOS) for such computation which allows to make a superstructure to implement specific computations and algorithms. To create MOS we used the nonlinear units (e.g., beta- barium borate crystal), arranged in series, powered with pulsed laser pump, and ended with the beam splitter to generate the output state of a number of entangled photon pairs. The computation is made by propagation of entanglement with beam splitters applied crossword and adjustable phase shifters that are tools for parameter steering. We show how to implement the series of cosine-based components on the example of two-component case. The results opens a broad area for future research in the area of building quantum optimizer using the quantum sampling methods and in the area of high precision temporal measurement of voltage, which is the important process for building high-fidelity devices.

Power quality is a major concern in electrical power systems. The power quality disturbances such as sags, swells, harmonic distortion and other interruptions have impact on the electrical devices and machines and in severe cases can cause serious damages. Therefore it is required to recognize and compensate all types of disturbances at an earliest to ensure normal and efficient operation of the power system. To solve these problems, many types of power devices are used. At the present time, one of those devices, Dynamic Voltage Restorer (DVR) is the most efficient and effective device used in power distribution system. In this paper, design and modeling of a new structure of multifunctional DVR for voltage correction is presented. The performance of the device under different conditions such as voltage swell, voltage sag due to symmetrical and unsymmetrical short circuit, starting of motors, and voltage distortion are described. Simulation result shows the superior capability of proposed DVR to improve power quality under different operating conditions. The proposed new DVR controller is able to detect the voltage disturbances and control the converter to inject appropriate voltages independently for each phase and compensate to load voltage through three single- phase transformers.

The popular motor drive systems with a single two-level voltage source inverter (VSI) have one main problem that is the occurrence of the common-mode voltage (CMV), which is an effect of the electromagnetic interference, shaft voltage, bearing currents, leakage current. These cause the high stress, increasung temperature and early mechanical failure in machine. To overcome this problem, the technology of the dual two-level VSI fed open-end three-phase ac loads is now available to eliminate the CMV at the ac/induction motor load with the 120-degree modulation technique for controlling each inverter. In this paper, the discontinuous space vector modulation (DSVM) schemes are proposed and applied for the dual two-level VSI fed open-end load. It is based on the 120-degree modulation technique by using only 12 active voltage vectors and the 10 zero voltage vectors from the total 64 voltage vectors along with the different five-segment swicthing sequence designs with centralizing pulse width modulation technqiue in order to not only cancel the CMV in the ac load, but also reduce the switching number/switching loss of the conversion system. Among the various DSVM schemes, their performances are compared in this paper, such as the number of the switching, the step and peak value of the CMV in each inverter, and the quality of the output waveform, etc. The details of the verfication and comparison are carried out by simulation using Matlab/Simulink software.

A scientific consensus is emerging on the benefits of dc distribution in medium voltage power systems of ships and cities. At least 50% space savings and increased power transfer capacity are estimated with enhanced voltage dc operation of electric cables. The goal of this research is to contribute to developing the empirical knowledge on the insulation performance in order to validate the feasibility of such anticipated gains of dc versus ac, and to determine the comparative impact of different operational conditions from a component engineering point of view. The partial discharge (PD) activity in cables is measured under ac and dc conditions as an indicator of insulation performance. Specifically, PDs in defects at the semicon-insulation interface are studied in terms of inception voltage, repetition rate and discharge magnitude. Empirical understanding is drawn for operating voltage and frequency dependence of the discharge behavior in such voids in the range of 10 to 20\,kV and 0 to 0.1\,Hz, respectively. The change in PD activity with void evolution is explored.

We recently found that in human osteoblasts Homer1 complexes to CaSR and mediates AKT initiation via mTORC2 leading to beneficial effects in osteoblasts including -catenin stabilization and mTORC1 activation (doi: 10.1074/jbc.RA118.006587). Herein we further investigated the relationship between Homer1 and CaSR and demonstrate a link between the protein levels of CaSR and Homer1 in human osteoblasts in primary culture. Thus, when siRNA was used to suppress the CaSR, we observed upregulated Homer1 levels and when siRNA was used to suppress Homer1 we observed downregulated CaSR protein levels using immunofluorescence staining of cultured osteoblasts as well as western blot analyses of cell protein extracts. This finding was confirmed in vivo as the bone cells from osteoblast specific CaSR(-/-) mice showed increased Homer1 expression compared to wild-type. Furthermore, when the commonly used osteosarcoma cell lines MG63 and SAOS-2 were compared to primary osteoblasts, higher levels of Homer1 protein were associated with increased protein levels of the CaSR as well as mTOR and Rictor. CaSR and Homer1 protein were both expressed in osteocytes embedded in the long bones of wild-type mice, and immunofluorescent studies of these cells revealed that Homer1 protein sub-cellular localization was markedly altered in the osteocytes of CaSR(-/-) mice compared to wt. The study identifies additional roles for Homer1 in the control of the protein level and subcellular localization of CaSR in cells of the osteoblast lineage, in addition to its established role of mTORC2 activation downstream of the receptor.

This work presents a new algorithm to resolve the problem of distribution network reconfiguration using the Tabu Search metaheuristic and voltage drop. The proposed method presents a different way to obtain the initial solution using the voltage drop, as well as a new way to generate a neighborhood of candidate solutions, based on randomness and the voltage drop, to perform a smooth and steady descent execution of the algorithm. The proposed algorithm has the main objective to reduce the active power losses in distribution networks, but it also achieves an refinement in the voltage profile. The proposed method was tested in two distribution systems, the 33-Bus and 94-Bus systems, commonly found and tested in the literature. The results of the tests show that the proposed method presents a low computational cost, achieves good solutions, and is better than the other methods found in the literature.

Mammals have two insulin-like growth factors (IGF) that are key mediators of somatic growth, of tissue differentiation and cellular responses to stress. Thus, the mechanisms that regulate the bioavailability of IGFs are important in both normal and aberrant development. IGF-I levels are primarily controlled via the growth hormone-IGF axis, in response to nutritional status, and also reflect metabolic diseases and cancer. One mechanism that controls IGF bioavailablity is the binding of circulating IGF to a number of binding proteins that keep IGF in a stable, but receptor non-binding state. But even before IGF is released from the cells that produce it, it undergoes an obligatory association with a ubiquitous chaperone protein, GRP94. This binding is required for secretion of a properly folded, mature IGF. This chapter reviews the known aspects of the interaction and highlights the specificity issues yet to be determined. The IGF-GRP94 interaction provides a potential novel mechanism of idiopathic short stature, involving the obligatory chaperone and not just IGF gene expression. It also provides a novel target for cancer treatment, as GRP94 activity can be either inhibited or enhanced.

Currently, energy security and environmental degradation are the two biggest challenges before humanity that can be surmounted with the use of green and sustainable biofuels produced from lignocellulosic crops. In the future, to ensure adequate and cost-effective supply of biofuels, it requires a sufficient amount of amenable and quality lignocellulosic feedstocks. Therefore, agricultural yields of lignocellulosic biomass crops should be substantially increased by intense genetic maneuvering of key gene regulatory mechanisms and signaling pathways that control plant biomass yield. Recently, numerous miRNAs families are identified, characterized, and validated across the plant kingdom. Plant microRNAs (miRNAs) are 21 to 24 nucleotides long, non-coding small RNAs, act as regulators of their target genes via inducing modifications in transcription, translation, and epigenome. MiRNAs represent many hallmark characteristics like sequence-specific regulation, tissue, and species-specific expression, evolutionary conservation, and functional diversity. They coordinate well physiological and life cycle processes in plants under adverse environmental conditions. Hence, miRNAs offer accurate, precise, and efficient regulatory switches in the miRNA-targeted genetic networks. It is evident from the study of the miR156 family and its target SQUAMOSA PROMOTER BINDING PROTEIN-LIKE (SPL) genes network that controls highly significant agronomic traits in crop plants. The miR156/SPL module acts as a master circuit that synchronizes many intricate complex biological functions such as growth and development, and metabolic processes by sensing internal and external environmental signals in plants. Therefore, miR156 can prove a potential target for miRNAs based plant biotechnology to harmonize complex biofuel traits and improve biomass yield in lignocellulosic biomass crops.

We previously reported how the loss of CHIP expression (Carboxyl terminus of Hsc70-Interacting Protein) during pressure overload resulted in robust cardiac dysfunction, accompanied by a failure to maintain ATP levels in the face of increased energy demand. In this study, we analyzed the cardiac metabolome after seven days of pressure overload and found an increase in long- and medium-chain fatty acid metabolites in wild-type hearts, a response that was attenuated in mice that lack expression of CHIP (CHIP^-/-). These findings suggest that CHIP may play an essential role in regulating oxidative metabolism, pathways that are regulated in part by the nuclear receptor PPARα (Peroxisome Proliferator-Activated Receptor alpha). Next, we challenged CHIP^-/- mice with the PPARα agonist, fenofibrate. Surprisingly, treating CHIP^-/- mice with fenofibrate for five weeks under non-pressure overload conditions resulted in a loss of skeletal muscle mass and a marked increase in cardiac fibrosis, accompanied by a decrease in cardiac function. Isolated CHIP^-/- cardiac fibroblasts treated with fenofibrate did not increase synthesis of collagen or TGFβ, suggesting that the fibrosis observed in CHIP^-/- hearts likely depends on signaling from other cell types or circulating factors. In conclusion, in the absence of functional CHIP expression, fenofibrate results in unexpected cardiac pathologies. These findings are particularly relevant to patients harboring loss-of-function mutations in CHIP and are consistent with a prominent role for CHIP in regulating cardiac metabolism.

A novel low-power MOS-only voltage reference is presented. The Enz-Krummenacher-Vittoz (EKV) model is adopted to provide a new perspective on the operating principle. The normalized charge density, introduced as a new variable, serves as an indicator when trimming the output temperature coefficient. The proposed voltage reference consists of a specific current generator and a 5-bit trimmable load. Thanks to the well-match between the current source stage and the output stage, the non-linear temperature dependence of carrier mobility is automatically canceled out. The circuit is designed in 55 nm COMS technology. The operating temperature ranges from -40 ∘C to 120 ∘C. The average temperature coefficient of the output voltage can be reduced to 21.7 ppm/∘C by trimming. The power consumption is only 23.2 nW with a supply voltage of 0.8 V. The line sensitivity and the power supply rejection ratio at 100 Hz are 0.011 %/V and -89 dB respectively.

The quickest and easiest way to avoid greenhouse gas (GHG) emissions is to purchase renewable electricity and offset the remaining emissions. However, the industrial sector’s electricity needs already exceed renewable electricity generation. Moreover, electricity accounts for only one third of the industry’s energy needs. Simultaneously, the advance of sectoral coupling and the decarbonisation of industrial processes, as well as the desire to rapidly decrease dependence on fossil fuels, are creating significant additional demand for renewable energy. Neither existing nor planned generation and transmission infrastructure will suffice to meet the expected short-term demand. Based on survey data from the German Industry Energy Efficiency Index, this article therefore examines the share of GHG savings that companies intend to achieve on- and off-site. Understanding how much additional generation and transmission capacity is needed by the industry to decarbonise and by when is crucial to identify and address the extent of excess demand. On average, companies plan to avoid 22 % of their 2019 emissions by 2025 and 27 % by 2030, primarily through on-site measures. In combination with the extrapolation of the entire industry’s needs for off-site capacity, the data calls for a rapid expansion of planning authority and green generation capacities.

This paper presents a comprehensive review that highlights the characteristics of non-isolated step-up converters based on high boost voltage lifting techniques. The paper categorises the high boost techniques: multistage/multilevel, switched capacitor, voltage multiplier, voltage lift, switched inductor, and magnetic coupling. The paper also discusses in detail the advantages and disadvantages for each category such as cost, complexity, power density, reliability and efficiency. The number of passive and active components, voltage gain, voltage stress, switching frequency, efficiency and power rating are also compared. Although the paper considers coupling inductors in the context of the non-isolated converter, the focus of the entire article is on the non-isolated high voltage step-up techniques. The key contribution in this paper is the review of high boosting techniques rather than the DC /DC converters. This allows divergence of new ideas and new power converters that will help provide highly efficient and flexible power converters for several applications where the sending end voltage is very low as photovoltaic systems. In addition, many applications and control techniques of DC/DC converters are summarised in this paper.

This paper reports a new control strategy to improve sharing of unbalanced currents in islanded LV microgrids. This technique provides fast and effective sharing of positive-, negative- and zero-sequence currents, and is the first example of zero-sequence current sharing in the literature. The controllers are designed in the stationary frame. The control structure consists of four loops; 1)~the current controller; 2)~the voltage controller; 3)~the droop controller and the 4)~negative and zero sequence current controllers. The output current is considered unknown for the controller and is added to the control system as a disturbance. The proposed controller features a high gain in fundamental and harmonic frequencies, hence a good voltage quality is obtained in the presence of unbalanced and nonlinear loads. To this aim, a proportional-resonant (PR) controller is adopted as the current controller. By using a multi-resonant controller as current controller, a unified control structure is obtained which is suitable for both grid-connected and islanded modes. The voltage controller is designed using a resonant controller so that the voltage can have low VUF and THD in the presence of unbalanced and nonlinear loads. Furthermore, in this paper droop method is applied to the control structure to share real and reactive powers. Simulation studies show that the conventional droop method cannot share the oscillatory part of the output power that is due to the presence of unbalanced loads in the microgrid. This paper relies on using zero and negative sequence virtual impedance controller to share the oscillatory part of output power. By using zero-sequence virtual impedance controller (ZSVIC) and negative-sequence virtual impedance controller (NSVIC), the zero and negative sequence currents in the microgrid are controlled and shared effectively. By compensating zero- and negative-sequence currents locally, the flow of these currents in the microgrid is minimized, and the overall power quality of the islanded LV microgrid is improved.

Background: Recent researches have investigated the biological importance of RNA N1-methyladenosine (m1A) modifications in oncogenesis and progression of head and neck squamous cell carcinoma (HNSCC). However, whether m1A modifications also have latent effect in tumor microenvironment (TME) generation and immune regulation in HNSCC is unknown. Methods: We evaluated the m1A modification patterns and related to these modification patterns with TME cell infiltration features in 1041 HNSCC samples by bioinformatics approach. Results: The m1A score is an independent prognostic indicator. HNSCC patients with low m1A score group with poor overall survival (OS) was mainly characterized by stroma activation, lack of sufficient immune infiltration, and exhibited an immune- desert TME phenotype. Low m1A scores were also correlated with increased tumor mutation burden (TMB), and HNSCC patients with high TMB and low m1A scores had the worst OS. In addition, anti-CTLA-4 combined with anti-PD1 treatment was more effective in the high m1A score subgroup than in the low m1A score subgroup. Conclusions: This study revealed that m1A modifications play a non-negligible role in developing the TME versatility and complexity of HNSCC. Assessing m1A modification patterns in HNSCC helps improve our comprehension of its TME infiltration profile and guides more effective immunotherapeutic approaches.

The paper proposes an innovative solution for managing and ensuring high energy efficiency of power supply systems at high non-linear loads. This is realized by maintaining optimal value of reliability indicators and high quality of power supply. The validation is carried out using analyzes and tests of quality of electromagnetic compatibility (EMC) for increased number of powered frequency converters. It has been proven that the effective use and reduction of energy consumption can be achieved thanks to the unique technological features of the employed electrical devices. This enables a normal operation of the system with decreased power and adequate control of energy processes. The problem of predicting power losses under changing conditions in a decentralized electrical network has been solved based on the theory of electromagnetic compatibility. The influence of the mains mode parameters and the indices of instantaneous distortion of current and voltage waveforms caused by the operation of converters on the resonance phenomena in power supply systems were investigated. Recommendations were developed for the selection of proper parameters of compensators for 6-10 kV and 0.4-0.66 kV circuits based on the analysis of the optimization problem when minimizing active power losses. Results of our findings may aid parties involved in designing and maintaining power networks in various applications, such as mines, etc.

In this research paper, a novel high step up dc-dc converter with a coupled inductor and voltage doubler circuits is proposed. The converter achieves a high step up voltage gain with an appropriate duty ratio and low voltage stress on the power switches. Also, the energy which is stored in the leakage inductor of the coupled inductor can be recycled to the output. The operating principles and the steady state analysis of the proposed converter are discussed in detail. Finally, a prototype circuit of the proposed converter is implemented in the laboratory in order to verify the performance of the proposed converter.

Voltage sags can cause the interruption of power supply and can negatively affect operations of customers. In this paper, the authors study the impact of battery energy storage systems (BESS) on voltage sags. A stochastic method of fault positions is used. Faults of various types are simulated and voltages are recorded. Firstly, with the BESS integrated into the network, there are higher residual voltages, fewer voltage sags and less expected critical voltage loss. Secondly, if the BESS converter power factor is reduced, recorded residual voltages are higher, voltage sags are fewer, and the number of expected critical voltage sags is lower. Finally, when three BESS converter control modes, namely constant voltage, constant power factor, and constant reactive power, were assessed, results showed similar voltage sag performances for constant power factor and constant reactive power modes. Furthermore, operating in constant voltage control outperformed the other two modes as it resulted in higher residual voltages, a lower number of voltage sags, and fewer expected critical voltage sags. The paper has demonstrated that the BESS can improve voltage sag performance. In addition, the power factor of the BESS converter and the mode of operation of the converter can influence the magnitude of the voltage sag performance improvement.

Our study explores the genetic mechanisms underlying the spotted leaf phenotype in rice, focusing on the rpt5a mutant characterized by persistent reddish-brown leaf spots from seedling stage to maturity, leading to extensive leaf necrosis. Through map-based cloning, we localized the responsible locus to a 330Kb region on chromosome 2 and identified LOC_Os02g56000 (named OsRPT5A) as the causative gene. A point mutation in OsRPT5A, substituting valine for glutamic acid, was identified as the critical factor for the phenotype. Functional complementation and generation of knockout lines in the IR64 background confirmed the central role of OsRPT5A in controlling this trait. Our study also revealed that OsRPT5A is constitutively expressed across various tissues, with its subcellular localization unaffected by mutations. Notably, we observed an abnormal accumulation of reactive oxygen species (ROS) in rpt5a mutants, suggesting a disruption in the ROS system. Complementation studies indicated OsRPT5A's involvement in ROS homeostasis and catalase activity regulation. Moreover, the rpt5a mutant exhibited enhanced resistance to Xanthomonas oryzae pv. oryzae (Xoo), highlighting OsRPT5A's role in rice's pathogen resistance mechanisms. These findings elucidate the genetic basis of the spotted leaf phenotype and emphasize the intricate interplay between plant defense responses and developmental pathways.

Phytochromobilin (PΦB) participates in the regulation of plant growth and development as an important synthetase of photoreceptor phytochromes (phy). And Arabidopsis Long Hy-pocotyl 2 (HY2) appropriately works as a key PΦB synthetase. However, whether HY2 takes part in plant stress response signal network remains unknown. Here, we described the func-tion of the HY2 in NaCl signaling. The hy2 mutant was NaCl-insensitive, whereas HY2-overexpressing lines showed NaCl-hypersensitive phenotypes during seed germination. The exogenous NaCl induced the transcription and the protein level of HY2 which positively mediated the expression of downstream stress-related genes of RD29A, RD29B and DREB2A. Further quantitative proteomics showed the patterns of 7,391 proteins under salt stress. HY2 was then found to specifically regulate 215 differentially regulated proteins (DRPs) which, according to GO enrichment analysis, were mainly involved in ion homeostasis, flavonoid biosynthetic & metabolic, hormone response (SA, JA, ABA, ethylene), reactive oxygen spe-cies (ROS) metabolic, photosynthesis and detoxification pathway to respond to salt stress. More importantly, ANNAT1-ANNAT2-ANNAT3-ANNAT4 and GSTU19-GSTF10-RPL5A-RPL5B-AT2G32060, two protein interaction networks specifi-cally-regulated by HY2, jointly participated in the salt stress response. These results direct the pathway of HY2 participating in salt stress, and provide new insights for the plant to re-sist salt stress.

Abstract: Aedes aegypti were exposed to water treated with mosquitocidal chips containing the insecticide pyriproxyfen in a polymer formulation. Chips were tested under different conditions; different water volumes, in containers made of different material, and in water with different levels of organic matter. Treated chips caused 100% mortality of Ae. aegypti during their pupal stage independent of conditions chips were exposed to in water. When tested for longevity, the chips containing 840 µg of pyriproxyfen killed 100% of Ae. aegypti for 4 sequential months of the chips being reused in water. Chips containing 8.4 µg of pyriproxyfen ceased to work after the first week of treatment. When mosquitocidal chips were used in > 25% of the oviposition containers within their cages, there was a significant control of the mosquito populations. Mosquitocidal chips worked in different environments, lasted for extended periods of time, caused significant mosquito population decreases, and were effective in controlling Ae. Aegypti.

This article presents a unique set of voltage and current data from a public building and acquired using a hybrid measurement solution that combines Python and Grafana. The transversal purpose consists of contributing to the community with a vision of the quality of the supply more oriented to the monitoring of the state of the network, providing a more realistic vision, which allows a better understanding, and the adoption of the best decisions to achieve the efficient energy management and thus optimize the operation and maintenance of power systems. The work focuses on higher order statistical estimators that, combined with exploratory data analysis techniques, improve the characterization of the shape of the stress signal. These techniques and data, together with the acquisition and monitoring system, present a unique combination in the line of low-cost measurement solutions. It also incorporates the underlying benefit of the contribution to industrial benchmarking. The paper also includes a computational comparison between Python and LabVIEW to elicit the performance of the measurement solution.

Preclinical evidence suggests that voltage gradients can act as a kind of top-down master regulator during embryogenesis and orchestrate downstream molecular-genetic pathways during organ regeneration or repair. Moreover, electrical stimulation shifts response to injury towards regeneration instead of healing or scarring. Cancer and embryogenesis not only share common phenotypical features, but also commonly upregulated molecular pathways. Ion channel activity is directly or indirectly linked to the pathogenesis of cancer hallmarks, while experimental and clinical studies suggest that their modulation may exert antitumor effects. A large recent clinical trial served as a proof-of-principle for the benefit of preoperative use of topical sodium channel blockade as a potential anticancer strategy against early human breast cancers. Apart from the obvious importance in perioperative medicine, it calls for the planning of further carefully designed clinical trials to expand on the concept of ion channels as tumor drivers.

To realize precise control of single quantum dots (Qdots) device, the high-performance bias source play the key role. In this paper, the 16-channel high precision voltage bias source prototype for Qdots device with 18-bit resolution was designed. The prototype was made and its performance was tested. The short time fluctuations can reach 50μV. The up-step and the down-step response time can achieve less than 3μs. The stability, linearity and setting time of the bias source exhibits good performance. What's more, the voltage bias source can be controlled by local and online. The results show that it is one effective and feasible topology for the high precision voltage bias source in Qdots device application.

Three-phase AC electric arc furnace (EAF) is a typical non-linear load, causing many power quality problems. Most of the researches on the voltage problems of EAF mainly focus on the voltage fluctuation, and less on the transient voltage problems caused by EAF short circuit and open circuit. In this paper, the relationship between voltage and current of EAF is obtained by combining hyperbolic function and exponential function, then the white noise and chaotic circuit are added to establish the EAF model which is suitable for the study of voltage fluctuation and transient voltage. This paper analyzes the causes of the transient voltage problem of the EAF, calculates the short-circuit current, reactive impact and the influence on voltage at the point of common coupling (PCC) in the three-phase short-circuit of the EAF, and compares the calculation results with the simulation results to prove the accuracy of this model. The results show that the reactive impact of three-phase short circuit is about twice as much as that of normal operation of EAF, resulting in about 30% voltage sag at the PCC, which is very unfavorable to the power grid. This paper provides reference for transient power quality evaluation and dynamic reactive power compensation of EAF.

An adaptive operation strategy for on-demand control of DMFC system is proposed as an alternative method to enhance the voltage stability. Based on a single-cell DMFC stack, a newly simplified semi-empirical model is developed from the uniform-designed experimental results to describe the I-V relationship. Integrated with this model, the multi-objective optimization method is utilized to develop an adaptive operation strategy. Although the voltage instability is frequently encountered in unoptimized operations, the voltage deviation is successfully decreased to a required level by adaptive operations with operational adjustments. Moreover, the adaptive operations are also found to be able to extend the range of operating current density or to decrease the voltage deviation according to ones requirements. Numerical simulations are implemented to investigate the underlying mechanisms of the proposed adaptive operation strategy, and experimental adaptive operations are also performed on another DMFC system to validate the adaptive operation strategy. Preliminary experimental study shows a rapid response of DMFC system to the operational adjustment, which further validates the effectiveness and feasibility of the adaptive operation strategy in practical applications. The proposed strategy contributes to a guideline for the better control of output voltage from operating DMFC systems.

This paper presents the implementation of a control strategy based on fuzzy logic artificial intelligence (AI) for speed regulation of an electromagnetic frequency regulator (EFR) prototype, aiming to eliminate the dependence on knowledge of physical parameters in the most diverse operating conditions. Speed multiplication is one of the most important steps in power generation wind. Gearboxes are generally used for this purpose. However, they have a reduced lifespan and a high failure rate and are still noise sources. The search for new ways to match the speed (and torque) between the turbine and the generator is an important research area to increase the energy, financial and environmental efficiency of wind systems. The EFR device is an example of an alternative technology that this team of researchers has proposed. It counts the fact of taking advantage of the main advantages of an induction machine with the rotor in a squirrel cage positively. In the first studies, the EFR control strategy consisted of the conventional PID controllers, which has several limitations widely discussed in the literature. This strategy also limits the EFR's performance, considering its entire operating range. The simulation program was developed using the Matlab/Simulink platform, while the experimental results were obtained in the laboratory emulating the EFR-based system. The EFR prototype used has 2 poles, a nominal power of 2.2 kW, and a nominal frequency of 60 Hz. Experimental results were presented to validate the efficiency of the proposed control strategy.

Wind power generation is one of the mainstream renewable energy resources. Voltage stability is as important as the frequency stability of a power system with a high penetration of wind power generation. The advantages of high-voltage direct current (HVDC) transmission systems become more significant with the increase of both installed capacity and transmission distance in offshore wind farms. Therefore, this study discusses about various voltage control methods for wind turbines and HVDC transmission systems. First, various voltage control methods of a wind farm were introduced, and they include QV control and voltage droop control. The reactive power of a wind turbine varies with active power, while the active power from each wind turbine may be different owing to wake effects. Thus, QV and voltage droop control with varying gain values were also discussed in this paper. Next, the voltage control methods for a HVDC transmission system, such as power factor control, voltage control, and Vac-Q control, are also summarized and tested in this study. When a three-phase short circuit fault occurs or a suddan reactive power load increases, the system voltage would drop immediately. Thus, various voltage control methods for wind turbines or HVDC can make the system's transient response more stable. Therefore, this study implemented the simulation scenarios, including a three-phase short circuit fault at the point of common coupling (PCC) or a sudden increase of reactive power load, and adopted various voltage control methods, which aims to verify whether additional voltage control methods are effective to improve the performance of transient voltage.

A novel high-voltage powerline inspection system is investigated, which consists of the cooperated ground vehicle and drone. The ground vehicle acts as a mobile platform that can launch and recycle the drone, while the drone can fly over the powerline for inspection within limited endurance. This inspection system enables the drone to inspect powerline networks in a very large area. Both vehicle’ route in the road network and drone’s routes along the powerline network have to be optimized for improving the inspection efficiency, which generates a new two-layer point-arc routing problem. Two constructive heuristics are designed based on “Cluster First, Rank Second” and “Rank First, Split Second”. Then local search strategies are developed to further improve the quality of the solution. To test the performance of the proposed algorithms, practical cases with different-scale are designed based on the road network and powerline network of Ji’an, China. Sensitivity analysis on the parameters related with the drone’s inspection speed and battery capacity is conducted. Computational results indicate that technical improvement on the inspection sensor is more important for the cooperated ground vehicle and drone system.

Traditional potential transformers have problems of large volume, difficulty in insulation, iron core saturation, ferroresonance overvoltage and poor transient response characteristics. The voltage sensor based on the principle of electric field coupling and differential input structure does not need to contact the measured object or ground, and can avoid the above problems. However, it requires a sufficiently high capacitance between the differential electrodes to obtain sufficient accuracy and a high voltage division ratio. The existing method of using mutual capacitance between the differential electrodes will cause many problems and fail to meet the practical needs. To solve the above problems, this paper innovatively uses multi-layer ceramic capacitor to replace the mutual capacitance and designs a new type of voltage sensor. In addition, by using single bypass small resistance grounding method to increase the input impedance of the differential signal processing circuit, error of the sensor is further reduced. The experimental results show that the sensor has excellent accuracy and great transient response characteristics. The ratio error under power frequency is within ±0.5% and the phase error is within 1. The ratio error in the range of 500 Hz∼30 kHz is within ±5% and the phase error is within 5. Moreover, it has the advantages of low cost, miniaturization, flexible shape and easy to adjust the voltage division ratio. These characteristics indicate that the sensor has good voltage measurement and sensor network potential.

Current-voltage characteristics curves of NFinFET are presented and are fitted with the modi-fied current-voltage (I-V) formulas, where the modified term in the triode region is demon-strated to be indispensable. In the as-known I-V formula, important parameters need determin-ing to make both the measured data and the fitting data as close as possible. Those parameters include kN (associated with the sizes of the transistor and mobility), (associated with Early Voltage), and Vth (the threshold voltage). The differences between the measured data and the fit-ting data vary as the applied source-drain bias, proving that the mobility of the carriers is not consistently constant. On the other hand, a modified formula, called kink effect factor, is nega-tively or positively added simulating solitary heat waves, which disturb the propagation of car-riers and thus influence the Source-Drain current (IDS). The new statistical standard deviations () are then found to be effectively suppressed as the kink effect is taken into account.

The general circuit topology and principles of low-noise high-voltage power supply are investigated to meet the requirements of the high-voltage bias application in air kerma meters. Two topologies, flyback converter and Royer converter are simulated using SPICE simulation program. The simulation results indicate that the circuit structure of the Royer converter is more complex, but it obtains lower output high voltage noise. While we develop an adjustable high-voltage power supply according to the circuit structure of the Royer converter, and tested it to ensure the design requirements for continuously adjustable output high-voltage linearity. The test results show that the linear adjustment rate is not more than ±0.0025%, the load regulation rate is less than ±0.1%, and the output ripple noise voltage percentage is less than 0.01%. These tested performance make it more suitable for accurate nuclear measurements.

In this paper consider the circuitry of voltage followers (VF) with unity-gain, intended for practical use in active Sallen-Key RC-filters (LPF, HPF, BPF, RF). The results of research and computer modeling of radiation-resistant and low-temperature VF in the LTSpice environment on models of CJFET transistors operating under the influence of neutron flux up to 10e14 n/cm2 and cryogenic temperatures up to -197°C are presented.

Increasing demand for electricity and modernization of power systems within competitive markets induce power systems to operate close to their stability limits. Therefore, a power system continuous monitoring and control by using voltage stability indices are known exigence. This is the first-ever effort, examined more than 40 voltage stability indices thorough an exhaustive study based in on their formulation, application, performance, and assessment measures. Which is conducted based on a logical and chronological order considering the most recent worldwide applied voltage stability indices. However, the generalizability of such an immense diversity of these indices in term of multivariable objectives subjects to a certain limitation to summate into a deciphered outcome. Despite all these obstacles, this study systematically reviews available indices in the literature within the past three decades to set out an integrated knowledge with an insight up-to-date exposition. That followed with a comparative analysis in term of their similarity, functionality, applicability, formulation, merit, demerit, and overall performances. Also, a broad categorization of voltage stability indices is addressed. This study with an immediate implication in practice as an exhaustive roadmap can be counted a planning and operation reference in the context of voltage stability for students, researchers, scholars, and practitioners.

By using 0.35-um CMOS process, this work achieves a design of analogous band-gap reference voltage circuit with low temperature coefficient. The proposed circuit operates at 3V and generates a reference current of 44 uA. The HSPICE simulation results show the temperature coefficient of this circuit is 23 ppm/℃ at range of -10 ℃ to 100 ℃, and the line regulation (the ratio of output current variation to supply voltage variation) is estimated as 1.95 uA/V from supply voltage variation of 3 V to 5 V. The experimental chip is fabricated and measured. The circuit provides adjustable capability for output voltage among temperature variation of -10 - 100 ℃. The chip area is 534 × 695 um^2. In this new design, the operational amplifier is not necessary. The chip design effort can be great reduced.

Skeletal myogenesis is an intricate process involving the differentiation of progenitor cells into myofibers, which is regulated by actin cytoskeletal dynamics and myogenic transcription factors. Although recent studies have demonstrated the pivotal roles of actin-binding proteins (ABPs) as mechanosensors and signal transducers, the biological significance of WAVE2 (Wiskott-Aldrich syndrome protein family member 2), an ABP essential for actin polymerization, in myogenic differentiation of progenitor cells has not been investigated. Our study provides important insights into the regulatory roles played by WAVE2 in the myocardin-related transcription factor A (MRTFA)-serum response factor (SRF) signaling axis and differentiation of myoblasts. We demonstrate that WAVE2 expression is induced during myogenic differentiation and plays a pivotal role in actin cytoskeletal remodeling in C2C12 myoblasts. Knockdown of WAVE2 in C2C12 cells reduced filamentous actin levels, increased globular actin accumulation, and impaired the nuclear translocation of MRTFA. Furthermore, WAVE2 depletion in myoblasts inhibited the expression and transcriptional activity of SRF and suppressed cell proliferation in myoblasts. Consequently, WAVE2 knockdown suppressed myogenic regulatory factors (i.e., MyoD, MyoG, and SMYD1) expressions, thereby hindering the differentiation of myoblasts. Thus, this study suggests that WAVE2 is essential for myogenic differentiation of progenitor cells by modulating the mechanosensitive MRTFA-SRF axis.

Only two percent of Glioblastoma multiforme (GBM) patients respond to standard care and survive beyond 36 months (long-term survivors, LTS) while the majority survive less than 12 months (short-term survivors, STS). To understand the mechanism leading to poor survival, we analyzed publicly available datasets of 113 STS and 58 LTS. This analysis revealed 198 differentially expressed genes (DEGs) that characterize aggressive tumor growth and may be responsible for the poor prognosis. These genes belong largely to the GO-categories “epithelial to mesenchymal transition” and “response to hypoxia”. In this paper we applied upstream analysis approach which involves state-of-art promoter analysis and network analysis of the dysregulated genes potentially responsible for short survival in GBM. Binding sites for transcription factors associated with GBM pathology like NANOG, NF-κB, REST, FRA-1, PPARG and seven others were found enriched in the promoters of the dysregulated genes. We reconstructed the gene regulatory network with several positive feedback loops controlled by five master regulators – IGFBP2, VEGFA, VEGF165, PDGFA, AEBP1 and OSMR which can be proposed as biomarkers and as therapeutic targets for enhancing GBM prognosis. Critical analysis of this gene regulatory network gives insights on mechanism of gene regulation by IGFBP2 via several transcription factors including the key molecule of GBM tumor invasiveness and progression, FRA-1. All the observations are validated in independent cohorts and their impact on overall survival is studied.

The CCAAT/enhancer-binding protein β (C/EBPβ) is a transcription factor that regulates cellular proliferation, differentiation, apoptosis and tumorigenesis. Although the pro-oncogenic roles of C/EBPβ have been implicated in various human cancers, how it contributes to tumorigenesis or tumor progression has not been determined. Immunohistochemistry with human non-small cell lung cancer (NSCLC) tissues revealed that higher levels of C/EBPβ protein are expressed compared to normal lung tissues. Knockdown of C/EBPβ by siRNA reduced the proliferative capacity of NSCLC cells by delaying G₂/M transition of the cell cycle. In C/EBPβ-knockdown cells, a prolonged increase in phosphorylation of cyclin dependent kinase 1 at tyrosine 15 (Y15-pCDK1) was displayed with increased Wee1 and decreased Cdc25B expression, simultaneously. ChIP analysis showed that C/EBPβ bound to distal promoter regions of WEE1 and repressed WEE1 transcription through the interaction with histone deacetylase 2. Treatment of C/EBPβ-knockdown cells with a Wee1 inhibitor induced a decrease in Y15-pCDK1 and recovered cells from G₂/M arrest. In the xenograft tumors, the depletion of C/EBPβ significantly reduced tumor growth. Taken together, these results indicate that Wee1 is a novel transcription target of C/EBPβ that is required for the G₂/M phase of cell cycle progression, ultimately regulating proliferation of NSCLC cells.

Concern about the planet's future has motivated governments around the world to adopt policies that promote more responsible energy consumption. Reducing emissions of the principal cause of climate change man-made greenhouse gases requires greater system efficiency and the utilization of renewable energy sources. The generation of electricity is the single largest source of hazardous pollutants, followed by the transportation sector. This is true due to the extreme reliance on petroleum and its derivatives that these industries have. Electric mobility is receiving more attention from businesses, governments, and academic institutions as a means to reduce the negative impacts of current energy consumption. Without measures to address common technical issues, electric vehicles would strain electrical infrastructure. In order to determine the best strategy for switching operations and feeder reconfiguration, this research presents a helpful hybrid genetic algorithm particle swarm optimization (HGAPSO) method. Meet transmission limits while decreasing real power losses and enhancing the system's bus voltage profile. The effects of HGAPSO on power losses and voltage distributions in the network are analyzed. Then, a report is produced contrasting GA and PSO. This cross-breeding of GA and PSO led to HGAPSO. This important problem can be solved more effectively with the use of new or improved algorithms. To find the optimal reconfiguration and properly rearrange transmission network interconnection, it employs a plethora of heuristic optimization algorithms. The objective is to limit bus voltage variations while maintaining the system's radial topology and minimizing power usage. The reliability and performance of the procedure were evaluated using MATLAB's IEEE 33-bus communication network. The outcomes demonstrate the effectiveness of the proposed technique, which cuts down on power waste during standalone runs and speeds up the processing time.

Typically, a diesel generator on the merchant ship, composed of a wound rotor synchronous generator and a four-stroke diesel engine, supplies electrical power to various loads. Recently, shaft generators for merchant vessels are increasingly replacing diesel generators to reduce CO2 emissions through fuel efficiency improvement. In particular, permanent magnet generators replace induction generators due to their high-efficiency characteristics at light loads. The surface-mounted permanent magnet can be a suitable rotor topology due to the relatively short constant power range. This generator can also operate as a motor according to the propulsion mode, so minimizing the harmonics of the induced voltage and the torque ripple is necessary. This paper proposes an alternative NdFeB magnet pole topology combined with the modular step-skewed rotor. The step-skewed rotor affects to reduce higher-order harmonics, and the modular pole reduces the permanent magnet assembly process and harmonics in voltage and torque. A 2-D finite element method is used to evaluate the harmonics of induced voltage and torque pulsation for the proposed topology. The topology shows harmonic minimization effect by comparing the characteristics of three flatted-bottom magnets. Compared to the tapered bread-loaf magnet, voltage harmonics to the 100th component are almost the same, and the torque ripple is reduced by more than 12% at the same residual flux density. The analysis method is verified by comparing test and analysis results for prototype machines with similar specifications.

Wenchuan earthquake that occurred in China in 2008 caused severe damage to a large number of electric substations. In this paper, Kriging interpolation method was used to calculate the impact area of the instrumental seismic intensity in Wenchuan earthquake, and to compare the intensities based on strong motion observation against the instrumental seismic intensities at locations where the observation data is available. The instrumental seismic intensities were calculated for the Wenchuan Earthquake at substations in the national power grid with voltage of 110kV or higher in areas of Mianyang, Deyang, Guangyuan and Chengdu. The cumulative Gaussian distribution function was then used to fit the relationship of the curves of the damage probabilities of high-voltage electrical equipment such as transformers, voltage mutual inductors, current mutual inductors, circuit breakers, isolating switches and lightning arrester with their instrumental seismic intensities. The damage probability density distribution curve of high-voltage electrical equipment based on the instrumental seismic intensities was obtained. The results showed that: (1) In the lower seismic intensity region, the mean instrumental seismic intensity was in good agreement with the traditional seismic intensity, but there was noticeable dispersion; in regions of intensity IX and above, the instrumental intensity was lower than the seismic intensity, but there was a lower degree of dispersion. (2) Among high-voltage electrical equipment, the transformers were most vulnerable to damage and they had some damage even under lower instrumental intensity. More damage would be produced when the instrumental intensity reached VIII or above; the second most vulnerable equipment was the circuit breaker, and the damage was most likely to occur when the instrument intensity was IX or above . (3) The damage rate curves of lightning arresters, current mutual inductors, voltage mutual inductors and isolating switches were relatively close to each other and the damage probability was the highest when the instrumental intensity was about X.

Wenchuan earthquake that occurred in China in 2008 caused severe damage to a large number of electric substations. In this paper, Kriging interpolation method was used to calculate the impact area of the instrumental seismic intensity in Wenchuan earthquake, and to compare the intensities based on strong motion observation against the instrumental seismic intensities at locations where the observation data is available. The instrumental seismic intensities were calculated for the Wenchuan Earthquake at substations in the national power grid with voltage of 110kV or higher in areas of Mianyang, Deyang, Guangyuan and Chengdu. The cumulative Gaussian distribution function was then used to fit the relationship of the curves of the damage probabilities of high-voltage electrical equipment such as transformers, voltage mutual inductors, current mutual inductors, circuit breakers, isolating switches and lightning arrester with their instrumental seismic intensities. The damage probability density distribution curve of high-voltage electrical equipment based on the instrumental seismic intensities was obtained. The results showed that: (1) In the lower seismic intensity region, the mean instrumental seismic intensity was in good agreement with the traditional seismic intensity, but there was noticeable dispersion; in regions of intensity IX and above, the instrumental intensity was lower than the seismic intensity, but there was a lower degree of dispersion. (2) Among high-voltage electrical equipment, the transformers were most vulnerable to damage and they had some damage even under lower instrumental intensity. More damage would be produced when the instrumental intensity reached VIII or above; the second most vulnerable equipment was the circuit breaker, and the damage was most likely to occur when the instrument intensity was IX or above . (3) The damage rate curves of lightning arresters, current mutual inductors, voltage mutual inductors and isolating switches were relatively close to each other and the damage probability was the highest when the instrumental intensity was about X.

The objective of this paper is to research the impact of electrical and physical parameters that characterize the complementary MOSFET transistors (NMOS and PMOS transistors) in the CMOS inverter for static mode of operation. In addition to this, the paper also aims at exploring the directives that are to be followed during the design phase of the CMOS inverters that enable designers to design the CMOS inverters with the best possible performance, depending on operation conditions. The CMOS inverter designed with the best possible features also enables the designing of the CMOS logic circuits with the best possible performance, according to the operation conditions and designers’ requirements.

Some management practices, such as maintaining birds under high group density, used in the poultry industry may cause birds stress, leading to injurious behaviors, such as injurious pecking, aggression, and cannibalism. In addition, some management practices used to prevent severe injuries in birds may cause pain. Beak trimming (BT), removal of 1/3 to 1/2 of a beak, is a routine husbandry procedure practiced in laying hens to prevent or reduce injurious behaviors. However, BT causes tissue damage, which may increase somatosensory sensitization of the damaged nerve tissues, resulting in pain (acute, chronic or both) in the treated birds because the beak is a complex, functional organ with an extensive nerve supply. BT has already been heavily regulated or prohibited in several European countries and, in time, this trend will impact the practice used in the United States poultry industry. With the growing public concern for poultry welfare there is a pressing need to identify and develop alternatives to BT. Probiotics defined “as a source of live (viable) naturally occurring microorganisms (direct-fed microbials)” have been used as dietary supplements or functional foods to target gut microbiota (microbiome) for prevention or therapeutic treatment of mental diseases including social stress-induced psychiatric disorders in humans and various experimental animals. In our studies, chickens were used as an animal model to assess if dietary supplementation of probiotic, Bacillus subtilis, reduces injurious behaviors following social challenge. Hens of Dekalb XL strain, an aggressive line, were used in the studies. Our results indicate that dietary supplementation of the Bacillus subtilis based probiotic reduces aggressive behaviors in chickens. These results suggest dietary probiotics could be a suitable strategy for increasing hosts’ health status and welfare conditions.

One of the rapidly developing research areas in the power system is the integration of distributed generation (DG) with the distribution system. The size and location of DG sources had a considerable impact on power system networks. Artificial intelligence (AI) techniques can be used to address multidimensional problems relating to DG size and location in distribution systems. Heuristic optimization offers a reliable and effective method for solving complicated real-world problems. This work focuses on a hybrid approach that combines the two heuristic optimization methods i.e., Particle Swarm Optimization (PSO) and Genetic Algorithm (GA) for the optimal siting and sizing of DG in distribution systems. This hybrid approach combines ideas from GA and PSO and generates individuals in a new generation using both PSO mechanisms and the procedures found in GA. An extensive performance analysis of the IEEE 14 busbar standard test system is conducted to demonstrate the viability of the suggested methodologies. In the designated locations, DG is placed, and the outcomes have been verified. The results indicated that the right placement of DG injection enhances the voltage profile and lowers the distributed system’s power losses. These techniques offer unique methods for determining the location of the DG unit, demonstrating the potential of such a computational techniques to reduce computing time and complexity while simultaneously reducing human errors associated with hit-and-trail methods.

Capacitor banks are widely used in current electrical transmission systems in order to improve power quality and increase efficiency. Utilizing high voltage components such as, shunt capacitors in the power grid imposes new challenges to the system which are required to be addressed. One of these challenges is corona discharges that can have negative impacts on capacitor banks such as power loss, insulator erosion followed by equipment failure, and radio interference. Although previous studies have almost exclusively focused on optimization of corona suppression rings for transformers and transmission lines, no specific studies have conducted regarding high voltage capacitor banks. This paper presents a novel study concerning verification and development of corona discharge suppression models on AC and DC capacitor banks with two different voltage levels. The employed method is based on the Maxwell’s equations and finite element method (FEM) which is implemented with the help of COMSOL Multiphysics© software. Results have verified the necessity of suppression methods as well as the efficiency of proposed solutions. Corona inception voltage levels are identified and effective factors on its appearance are reviewed. Analyses of proposed solutions have shown significant improvements in optimization of corona suppression methods as well as enhancement of maintenance maneuverability.

The purpose of this study is to investigate the impact of the voltage drop of a three-phase voltage source inverter in driving brushless motors. This study also proposes an enhanced Field Oriented Control scheme that accounts for the inverter voltage drop enabling efficient drive at very low motor-speeds. Experimental results are provided to verify the theoretical study and the proposed control scheme.

This work introduces an innovative approach that unites a PIDND2N2 controller and the balanced arithmetic optimization algorithm (b-AOA) to enhance the stability of an automatic voltage regulator (AVR) system. The PIDND2N2 controller, tailored for precision, stability, and responsiveness, mitigates the limitations of conventional methods. The b-AOA optimizer is obtained through integration of pattern search and elite opposition-based learning strategies into the arithmetic optimization algorithm. This integration optimizes the controller parameters and the AVR system's response, harmonizing exploration and exploitation. Extensive assessments, including evaluations on 23 classical benchmark functions, demonstrate the efficacy of the b-AOA. It consistently achieves accurate solutions, exhibits robustness in addressing a wide range of optimization problems, and stands out as a promising choice for various applications. In terms of AVR system, comparative analyses highlight the superiority of the proposed approach in transient response characteristics, with the shortest rise and settling times and zero overshoot. Additionally, the b-AOA approach excels in frequency response, ensuring robust stability and a broader bandwidth. Furthermore, the proposed approach is compared with various state-of-the-art control methods for the AVR system, showcasing impressive performance. These important results underscore the significance of this work, setting a new benchmark for AVR control by advancing stability, responsiveness, and reliability in power systems.

This paper considers the principles of building a circuit model of film resistor cutting. The conductive resistive medium is defined with the component equations and the topology of the circuit model. A method of estimating the electric parameters of a resistor operating in the system with a measuring voltage source is shown. An equation system for the node voltages is defined, and the resistive layer parameters are analyzed as the circuit model structure changes during the cutting process.

Based on Venturini method, it is in favor of the modulation technique for controlling the matrix converter due to only use of the comparison between the duty cycles in time domain and the triangular carrier wave for generating the gating signals and the achievable voltage ratio between fundamental output magnitude and fundamental input magnitude to 0.866. However, even with simple modulation method and achieving maximum fundamental output magnitude, the possible input voltage unbalance conditions accordingly influence on the output performances (more reduction and distortion). Thus, a modified Venturini modulation method is presented in this paper, in order to solve the problems of unbalanced input voltage conditions on the matrix converter performances. The proposed strategy is to satisfy the desirable feature of the duty cycle modulating waves, as generated in the event of normal situation. Up to this approach, it can support either single-phase condition or two-phase condition. Performance of the proposed control strategy was verified by the simulated implementation in the MATLAB/Simulink software with showing good steady-state and dynamic operations.

The Hippo pathway plays crucial roles in governing various biological processes during tumorigenesis and metastasis. Within this pathway, upstream signaling stimuli activate a core kinase cascade, involving MST1/2 and LATS1/2, which subsequently phosphorylates and inhibits the transcriptional co-activators YAP and its paralog TAZ. This inhibition modulates the transcriptional regulation of downstream target genes, impacting cell proliferation, migration, and death. Despite the acknowledged significance of protein kinases in the Hippo pathway, the regulatory influence of protein phosphatases remains largely unexplored. In this study, we conducted the first gain-of-functional screen for protein tyrosine phosphatases (PTPs) regulating the Hippo pathway. Utilizing a LATS kinase biosensor (LATS-BS), a YAP/TAZ activity reporter (STBS-Luc), and a comprehensive PTP library, we identified numerous novel PTPs that play regulatory roles in the Hippo pathway. Subsequent experiments validated PTPN12, a master regulator of oncogenic receptor tyrosine kinases (RTKs), as a previously unrecognized negative regulator of the Hippo pathway effectors, oncogenic YAP/TAZ, influencing breast cancer cell proliferation and migration. In summary, our findings offer valuable insights into the roles of PTPs in the Hippo signaling pathway, significantly contributing to our understanding of breast cancer bi-ology and potential therapeutic strategies.

Due to advances in power electronics technology and the evolution of automation devices, the number of electrical devices that are sensitive to power quality is rapidly increasing, and for this reason, users are increasing their demand for high quality. To meet power quality demands, many power conversion devices are used, including dynamic voltage restorers (DVRs). DVRs are rec-ognized as devices that can effectively manage problems such as voltage segment, swells, and harmonics. DVR control requires many samples for harmonic compensation, which has the dis-advantage of being complicated to implement due to fast digital signal processing computation and the application of the cyclic discrete Fourier transform. In this paper, a high-precision DVR system configuration is proposed that compensates for harmonics using a periodically equivalent time-interval sampling technique and a novel circular structured memory filter. The proposed circular structured multi-pointer memory filter is an effective filter algorithm for high-precision input voltage measurement because it can remove noise and compensate for the delay of the phase angle of the filter in voltage measurement. A simulation and DVR prototype system was built, and the feasibility and effectiveness of the phase angle multi-filter voltage detection method and the compensation method were verified by experiments.

Recent years have seen a rapid uptake in distributed energy resources (DER). Such technologies pose a number of challenges to network operators, which can ultimately limit the amount of rooftop solar photovoltaics (PV) systems that can be connected to a network. The objective of this industry-based research was to determine the potential network effects of forecast levels of customer owned rooftop solar PV on Energy Queensland’s distribution network and formulate functions that can be used to determine such effects without the requirement for detailed network modeling and analysis. In this research, many of Energy Queensland’s distribution feeders were modelled using DIgSILENT PowerFactory and analyzed with forecast levels of solar PV and customer load. Python scripts were used to automate this process and quasi dynamic simulation (QDSL) models were used to represent the dynamic volt-watt and volt-var response of inverters, as mandated by the Australian Standard AS/NZS 4777. In analyzing the results, linear regression was used to form trend equations that represent various network characteristics against the number of PV connections. The trend equations provide a way of approximating network characteristics for other feeders under various levels of customer owned rooftop solar PV without the need for detail modeling.

This study utilized electron back scattered diffraction (EBSD) and X-ray diffraction (XRD) to investigate the impact of inter-annealing temperature and heating rate of final annealing on the microstructure of high-voltage anode aluminum foils. The findings indicate that the formation of cube texture in the final products is significantly influenced by the inter-annealing temperature, as low inter-annealing temperatures retain a considerable amount of deformation stored energy, providing a strong driving force for nucleation. The cube texture is observed to deviate from the ideal position at lower inter-annealing temperatures. Additionally, an increase in heating rate during final annealing leads to a gradual decrease in the fraction and grain size of recrystallization. This is attributed to the fact that a higher heating rate (below the critical heating rate) reduces the time available for grain boundary migration, thereby slowing the recrystallization process.

Lead-free ferroelectric perovskite N-methyl-N'-diazabicyclo[2.2.2]octonium)–ammonium triio-dide, MDABCO-NH₄I₃, nanocrystals are embedded in three different polymer fibers fabricated by the electrospinning technique. The nanofibers, which are very flexible and have a high Young modulus, behave as active piezoelectric energy harvesting sources that produce a piezoelectric voltage coefficient up to geff = 3.6 VmN-1 and show a blue intense luminescence band at 325 nm. In this work, the pyroelectric coefficient is reported for the MDABCO-NH₄I₃ perovskite inserted in electrospun fibers. At the ferroelectric-paraelectric phase transition, the embedded nanocrystals display a pyroelectric coefficient as high as 194×10-6 Cm-2k-1, within the same order of magnitude as that reported for the state-of-the-art bulk ferroelectric triglycine sulfate (TGS). The perovskite nanocrystals embedded into the polymer fibers remain stable, and no degradation is caused by oxidation.

Triple-negative breast cancer (TNBC) is a subtype of breast cancer that disproportionally accounts for the majority of breast cancer-related deaths due to the lack of specific targets for effective treatments. While there is immense focus on the development of novel therapies for TNBC treatment, a persistent and critical issue is the rate of heart failure and cardiomyopathy which is a leading cause of mortality and morbidity amongst cancer survivors. In this review, we highlight mechanisms of cardiotoxicity post-chemotherapeutic exposure, assess how this is assessed clinically and highlight the transforming growth factor-beta family (TGF-β) pathway and discuss its role as a mediator of cardiomyopathy. We highlight recent findings demonstrating TGF-β inhibition as a potent method to prevent cardiac re-modeling, fibrosis and cardiomyopathy. We describe how dysregulation of the TGF-β pathway is associated with negative patient outcomes across 32 types of cancer including TNBC. We then highlight how TGF-β modulation may be a potent method to target mesenchymal (CD44+/CD24-) and epithelial (ALDHhigh) cancer stem cell (CSC) populations in TNBC models. CSCs are associated with tumorigenesis, metastasis, relapse, resistance, and diminished patient prognosis; however, due to plasticity and differential regulation these populations remain difficult to target and persist as a major barrier barring successful therapy. TGF-β inhibition represents an intersection of two fields: cardiology and oncology. Through inhibiting cardiomyopathy, cardiac damage and heart failure may be prevented and through CSC targeting, patient prognosis may be improved. Together, both approaches, if successfully implemented would target the two greatest causes of cancer-related morbidity in patients and potentially lead to a breakthrough therapy.

This article introduces the design and analysis of a slope detection circuit tailored for on-chip sensing of the load current in DC-DC converters. The novel indirect sensing approach is grounded in measuring the output voltage slope across the filtering capacitor during discharge phases. Consequently, this slope data can be effectively harnessed to control the converter switches. The slope detector circuit was designed in standard 65 nm CMOS technology using the nominal supply voltage of 1.2 V and can be used for current sensing within the range from one to hundreds of mA. Since the proposed circuit has mainly digital character, the robustness to process, temperature and supply voltage variations can be ensured rather conveniently.

With the widespread application of Voltage Source Converter (VSC) in the power system with high penetration of renewable resources, the problem of wideband oscillations caused by the interaction between the power converters and the power grid has drawn large attention. This paper presents a new methodology for simplifying the mathematical derivations of the impedance model of VSC. Using the new simplified model, the stability and the spectrum characteristic of the performance of the VSC can be clearly analyzed. The proposed second-order d-q impedance model of the grid connected VSC at presence of PLL, not only mathematically proves that the wideband oscillatory modes always occurs in conjugate pairs, but also deliver a clear vision of the physical essence of the wideband oscillations. The classic modal analysis is executed in the paper to demonstrate the stability and frequency spectral characteristics of the wideband oscillations in the VSC integrated system. The impact of control parameters of the VSC on the wideband oscillatory stability is thouroughly analyzed using the results of the modal analysis. The methodology can be considered a powerful tool for the control design of VSC in the modern power system.

Ice covering on overhead transmission lines would cause damage to transmission system and long-term power outage. Among various de-icing devices, modular multilevel converter (MMC) based DC de-icer (MMC-DDI) is recognized as a promising solution due to its excellent technical performance. Its principle feasibility has been well studied, but few literature discuss its economy or hardware optimization, thus the designed MMC-DDI for high voltage transmission lines is usually too large and too expensive for engineering applications. To fill this gap, this paper presents a quantitative analysis on the converter characteristics of MMC-DDI, and calculates the minimal converter rating and its influencing factors. It reals that, for a given de-icing requirement, the converter rating varies greatly with its AC-side voltage. Then an optimization configuration is proposed to reduce the converter rating and improve its economy. The proposed configuration is verified in a MMC-DDI for a 500kV transmission line as a case study. The result shows, in the case of outputting same de-icing characteristics, the optimized converter rating is reduced from 151 MVA to 68 MVA, and total cost of MMC-DDI is reduced by 48%. This analysis and conclusion are conductive to the optimized design of multilevel DC de-icer, then to its engineering application.

The paper presents dynamic and transient behaviour of the Doubly Fed Induction Generator (DFIG) in the wind farms. When Voltage sag or any faults occurs in the network, the variables in the doubly Fed Induction Generators are varying severely. If the voltage sag occurs, Active and Reactive power that generated by the DFIG will decrease and will increase respectively, The DC voltage link will be bigger, and the rotor current will increase. The DFIG in the wind farms uses Proportional Integral controller for controlling of electronic devices (Rotor Side Converter and Grid Side Converter). Even though the model of Doubly Fed Induction Generators and electronic device in the paper are linear, The Proportional Integral controllers cannot protect and control the variables. So, the power electronic converters and the DC-link can damage due to over voltages and over currents. Doubly Fed Induction Generator in the wind farm is simulated in MATLAB software. The results of the simulation present over voltage and over current in the DC-link and in the rotor of the Doubly Fed Induction Generator. In addition, it will explore the effect of Proportional Integral controller in Doubly Fed Induction Generator when three-phase short circuit fault occurs

Frequency, amplitude and phase information of the grid voltage are of great importance in constructing a robust controller structure for grid connected inverter systems. This paper presents a simple and robust approach for the instantaneous estimation of positive and negative sequence voltage components under distorted voltage conditions. A second order generalized integrator (SOGI) is used to filter the distorted voltage and to generate orthogonal voltage components for each of the three phases. These filtered and orthogonal components are used for instantaneous calculation of symmetrical components. The implemented method is frequency adaptive; the method is demonstrated and compared to a conventional phase locked loop (PLL) technique with both MATLAB/Simulink simulations and experiments utilizing the dSPACE ds1103 digital controller.