In the drive towards environmental restoration and sustainable energy solutions, effective utilization and management of agricultural crop residues are vital to mitigate greenhouse gas (GHG) emissions and waste accumulation. Converting biogenic wastes into biofuels and bioproducts has the potential to tackle the energy crisis and contribute to environmental remediation. In this investigation, teff husk, primarily generated in Ethiopia during teff production within the agro-industrial sector, is used as the feedstock for the slow pyrolysis process. In Ethiopia, it is estimated that over 1.75 million tons of teff husk are generated annually, with a significant portion being incinerated in the fields, resulting in substantial environmental pollution. This study focuses on assessing teff husk as a potential material for slow pyrolysis, a crucial stage in biochar production, to tap into its biochar-producing potential. To determine the composition of the biomass, the teff-husk was initially analyzed by thermogravimetry. The significant presence of fixed carbon indicates that teff husk is a viable candidate for pyrolytic conversion into biochar particles. The process of slow pyrolysis took place at three varied temperatures—specifically, at 400, 450, and 500 °C. Process parameters of slow pyrolysis such as reaction time, temperature, and heating rate were enhanced to obtain maximum biochar yields. The highest biochar yield of 43.4 wt% was recorded at optimized reaction time, temperature, and heating rate of 120 min, 400 °C, and 4.2 °C/min, respectively. Furthermore, biochar's physicochemical, SEM-EDX, FTIR, and TGA characterization were performed. The thermal stability and carbon content of biochar were found to rise at higher temperatures. Unlike fuel recovery, the results suggest that teff-husk can be used as a feedstock for biochar production.

This paper investigates an alternative use of sterile aggregate materials which may arise from various construction applications in conjunction with other low-cost mineral raw materials to remediate the acid mine drainage phenomenon. This study is based on the combination of unprocessed mineral raw materials as well as on the basic concept of the cyclic economy where the conversion of a waste into a raw material for another application can be achieved. In this way, the value of mineral raw materials can be prolonged for as long as possible, waste generation and exploitation of natural resources are minimized and resources are kept as far as possible within the existing economy. In this study, an electrically continuous flow driven forced device proposed and demonstrated for the remediation of waste water in lab-scale by using certain mixes of mineral raw materials (serpentinite, andesite, magnesite, peat and biochar). Our results focus on the impact of the studied mineral raw materials and especially on their synergy on the water purification potential under continuous water flow operation. Using the proposed 7-day experimental electrically continuous flow driven forced device with the certain mixes of mineral raw materials, the increase of pH values from 3.00 to 6.82 as well as significant removal of Fe, Cu and Zn was achieved.

The Earth's fresh water resources predominantly is groundwater that is pumped out due to rapid urbanization and aggravated by climate change. Groundwater modeling is a crucial tool for understanding aquifer systems, employing 1D, 2D, and 3D numerical models with distinct applications. One-dimensional models focus on vertical dynamics, examining aquifer properties and simulating vertical contaminant transport. Two-dimensional models extend to regional scales, considering horizontal variations and assessing groundwater-surface water interactions, making them valuable for watershed-scale studies. Three-dimensional models provide a comprehensive representation of hydrogeological systems, capturing intricate flow patterns and aiding site-specific assessments. Comparative analysis reveals model strengths and limitations, emphasizing the importance of calibration for reliable results. Case studies showcase practical applications, such as 1D models in flooding analysis and 2D models for simulating debris flows. Three-dimensional modeling proves essential for understanding complex river-aquifer exchange fluxes. Future directions call for a global groundwater platform to address data variability and technical challenges. Despite substantial investments required, the anticipated returns in scientific advancements, societal benefits, and economic gains are expected to outweigh the initial costs. This review aims in highlighting the significance of advancing all three-dimension groundwater modeling for sustainable water resource management and environmental protection.

Mining activities often generate important amounts of extractive waste, and as a consequence, environmental impacts that affects all factors to a greater or lesser extent. Depending on a variety of variables, the impact can be permanent or temporary, reversible or irreversible, negative or positive. This study conducted research on the status of closure and remediation processes of mining areas in Romania, specifically in the counties of Maramureș, Suceava, Harghita, Alba, Hunedoara, and Caraș-Severin. Furthermore, based on the type and level of pollution, the degree of application of remediation techniques for water and soil pollution in the investigated mining areas was studied. From the analysed information, it is evident that although the closure and remediation process started in Romania over 20 years ago, unfortunately, to this day, the technical projects, technical assistance, and execution of closure and remediation works have not yet completely solved the complex environmental issues in the mining sector. Most of the tailing ponds and waste piles of former mines continue to pose permanent specific risk to the environment and the population. This study concludes that the mining sector in Romania, although it has the necessary techniques and technologies for the ecological rehabilitation of degraded lands related to the Extractive Waste Facilities and the elimination of negative impacts on the environment and public health, has not yet been able to fully concretize its remediation efforts.

Improper disposal of waste plastic has caused serious ecological and environmental pollution problems. Transforming plastics into high value-added chemicals can not only achieve efficient recycling of waste plastics, but also an effective way to control white pollution. The catalyst selectively breaks the C-C bond of polyolefin plastic under heat treatment and converts it into liquid fuel, thus realizing sustainable recycling of plastics and has a good development prospect. This review provides a detailed overview of the current development of catalytic pyrolysis, catalytic hydrolysis, solvent decomposition and supercritical hydrothermal liquefaction for cracking plastics to make fuel oil. The reaction mechanism, influencing factors and promoting effects of catalysts in various degradation technologies are analyzed and summarized and the latest proposed tandem reaction for degrading plastics is briefly introduced. Finally, some optimization paths of waste plastic pyrolysis to fuel oil technology are proposed: synergies between mixed raw materials, in-depth exploration of catalysts, design and manufacture of reactors that match the pyrolysis technology. All these are important research directions for promoting the industrialization of plastic pyrolysis to fuel oil.

Microbial Fuel Cells (MFCs) representing a promising technology for the extract of energy and resources through wastewater and it also offer an economic solution to the problem of environment effluent and energy crisis in near future. The advance device is rather appealing, due its potential benefits, its practical application is, however hindered by several drawbacks, such an internally competing microbial reaction, and low power generation. This report is an endeavor to address various design connected to the MFCs application to wastewater treatment, in particular cost effective bioelectricity from waste water are reviewed and discussed with a multidisciplinary approach. The conclusions drawn herein can be of practical interest to all new researchers dealing with effluent wastewater treatment using MFCs.

The aim of this study was utilization of ground tea waste (GT) left after brewing the black tea as a biofiller of natural rubber (NR) composites. Ionic liquids (ILs), i.e., 1-ethyl-3-methylimidazolium lactate and 1-benzyl-3-methylimidazolium chloride, often used to extract phytochemicals from tea, were applied to improve the dispersibility of GT particles in elastomeric matrix. The influence of GT loading and ILs on curing characteristics, crosslink density, mechanical properties, thermal stability and resistance of NR composites to thermo-oxidative aging was investigated. The amount of GT did not significantly affect curing characteristics and crosslink density of NR composites, but had serious impact on tensile properties. Applying 10 phr of GT improved the tensile strength by 40% compared to unfilled NR. Further increasing in GT content worsened the tensile strength due to the agglomeration of biofiller in elastomer matrix. ILs significantly improved the dispersion of GT particles in elastomer and increased the crosslink density by 20% compared to the benchmark. Owing to the poor thermal stability of pure GT, it reduced the thermal stability of vulcanizates compared to unfilled NR. Most importantly, GT-filled vulcanizates showed improved resistance to thermo-oxidative aging, since the aging factor increased by 25% compared to the unfilled vulcanizate.

Silica fly ash, Certyd aggregate, and an alkaline solution were used to produce lightweight geo-polymer concretes. The compressive strength, water absorption, bulk density and SEM photos showing the structure of the obtained composite were carried out. Tests conducted on the specifi-cation of lightweight geopolymer concretes have revealed significant chemical interactions between the ash aggregate and the geopolymer mortar, particularly when the coarse aggregate surface has been pre-treated with an alkaline solution. Statistical analysis of the experimental data, which in-vestigated the influence of three key variables on compressive strength, water absorption, and bulk density of Lightweight Geopolymer Concrete (LBG), identified the following factors as having the most substantial impact: the quantity of alkali used, the curing temperature, and the concentration of alkali in the mixture. The optimal test series exhibited a commendable compressive strength of 20.14 megapascals (MPa), accompanied by a water absorption rate of 14.72% and a bulk density of 1486.6 kilograms per cubic meter (kg/m³). These findings underscore the importance of alkali con-tent, curing temperature, and alkali concentration in tailoring the properties of lightweight geo-polymer concrete to meet specific performance requirements.

In an attempt to reuse fibrous textile waste and, at the same time, to address dye pollution in textile wastewater, waste cotton-based yarn was utilized as both a cheap and sustainable adsorbent and a precursor for carbon adsorbent production. Cotton and cotton/polyester yarn samples underwent thermal modification through carbonization followed by chemical activation with KOH. Various techniques including nitrogen adsorption-desorption isotherms, scanning electron microscopy, Fourier transform infrared spectroscopy, and surface charge determination were employed to analyze the morphological and surface properties of the cotton-based adsorbents. Adsorption properties were evaluated by testing the removal of selected cationic and anionic dyes from water. The impact of temperature, contact time, initial concentration, and pH of the adsorbate solution on adsorption was investigated, with experimental data analyzed using theoretical models. While carbonization alone did not significantly enhance adsorption properties, activated samples exhibited high efficacy in removing both cationic and anionic dyes from water. Despite the negative influence of the polyester component in the carbon precursor on the efficiency of activated samples in removing methyl orange, results indicated that activated cotton and cotton/polyester yarn could be used to prepare highly efficient adsorbents for the rapid removal of methylene blue from real wastewater samples.

Households and businesses are generating unprecedented levels of electrical and electronic wastes (e-waste), fueled by modernisation and rapid obsolescence. While the challenges imposed by e-waste are similar everywhere in the world, disparities in progress to deal with it exists; with developing nations such as South Africa lagging. The increase in e-waste generation increases the need to formulate strategies to manage it. This paper presents an overview of e-waste management on a global and South African scenarios with a specific case for Cathode Ray Tube (CRT) waste management practices in South Africa. CRTs present the biggest problem for recyclers and policy makers because they contain hazardous elements such as lead and antimony. Common disposal practices have been either landfilling or incineration. The research into the South African practices with regards to CRT waste management showed that there is still more to be done to effectively manage this waste stream. This is despite clear waste regulatory frameworks in the country. However, recent developments have placed e-waste as a priority waste stream, which should lead to intensified efforts in dealing with it. Overall, these efforts should aim to maximise diversion from landfilling and to create value-addition opportunities, leading to social and environmental benefits.

Solvent free copolymerization of epoxides derived from fatty acid esters of waste cooking oil with phthalic anhydride using (salen)CrIII Cl as catalyst and n-Bu4NCl/DMAP as co-catalyst was carried out for the first time under microwave irradiation, where reaction time was reduced from number of hours to minutes. The polyesters were obtained with molecular weight (Mw = 3084-6740 g/mol) and dispersity values (D = 1.18-1.92), when (salen)CrIII Cl/n-Bu4NCl was used as catalysts. While in case of DMAP as a co-catalyst, polyesters with improved molecular weight (Mw = 5537-6925 g/mol) and narrow dispersity values (D = 1.07-1.28) were obtained even at reduced concentrations of (salen)CrIII Cl and DMAP. The obtained products were characterized and evaluated by attenuated total reflection-fourier transform infrared spectroscopy (ATR-FTIR), proton nuclear magnetic resonance (1H-NMR) spectroscopy, gel permeation chromatography (GPC) and thermogravimetric analysis (TGA) Techniques.

Waste glycerol can be subjected to various processing operations, including purification and re-fining, to obtain glycerol of appropriate purity. In addition, alternative methods of utilising waste glycerol are also being sought, e.g. by converting it into other valuable chemical products or biofuels. Therefore, various technologies are being developed to utilise this type of waste effectively and sustainably. The production of value-added products from waste glycerol is an important issue that determines the improvement of the economic viability of biofuel production and corresponds to the model of a waste-free and emission-free circular economy. This paper characterised the mechanisms and evaluated the efficiency of existing methods of microbiological utilisation of waste glycerol into liquid biofuels, including biodiesel, bioethanol and biobutanol, and identified further directions for the production of value-added products. In addition, a bibliographical analysis of publications re-lated to the production of liquid fuels and economically valuable products from glycerol was carried out, the progress of research and application work was assessed and directions for future research were identified.

The invention of nanoscience not only brings a revolutionary change in the field of science but also changed the direction of research. Today the whole world is under the trigger of nano and nanoparticles have multidimensional applications in every aspect of life including environmental point of view. Till today a plethora of nanoparticles have been synthesized and have also been applied for multiple purposes and hence grabbed the attention of researchers all over the world. Among the bunch of NPs discovered to date, we have a particular interest in silver nanoparticles (AgNPs) because of their cost-effectiveness and huge abundance in the earth’s crust. With respect to every passing day, due to various kinds of anthropological activities, the quality of the environment such as air, water and soil is depleting which ultimately hampers the human civilization. To encompass the growing environmental issues, many techniques have been adopted. Among the many strategies, tackling the current issues regarding environment through nanoscience is highly worthy as because of its cost-effectiveness, less time consuming and easy handling process. This article reviews the potential of nanoparticles, particularly silver nanoparticles, for a wide range of environmental applications, such as soil, air, and water remediation.

Recycling information can be complex and often confusing which may subsequently reduce the participations in any waste recycling schemes. As a result, this research explored the roles as well as the importance of a holistic approach in designing recycling information using 15 expert-based in-depth interviews. The rationale was to offer a better understanding of what constitutes waste, recycling, and how recycling information should be designed and presented to make recycling more attractive/convenient. Based on the research participants’ perceptions with supports from the existing studies, this research sub-categorised recycling information into three different themes, termed the “WWW” of recycling information components. As a result, these components (or attributes) were extensively described (using findings of semi-structured interviews) to elicit pragmatic guidance for practitioners, policy-makers, and other stakeholders in designing structured communication or information strategies that may simplify and subsequently increase waste-recycling practices. The policy implications of holistic information in enhancing recycling are further discussed.

Copper-based nanomaterials in the last decade attracted many researchers due to their extensive practical applications, unique, inexpensiveness, and wide availability. In addition to this, copper-based nanomaterials possess good thermal stability, and selectivity and also possess high activity. This review emphasis on the recent advances in the synthesis of copper nanomaterials and their wide applications in the field of environmental catalysis. This review aims to fill a significant knowledge gap in the different areas of environmental pollution management. Also, the paper concentrates on the recent applications of copper-based nanomaterials for environmental remediation, including the removal of heavy metals, and degradation of organic pollutants such as pharmaceuticals, and other environmental contaminants. Also, it will be helpful to young researchers in improving the suitability of implementing the Copper nanomaterials in the right way establishing and achieving sustainable goals for environmental remediation.

The global increase in population has placed significant pressure on food security, leading to the emergence of aquaculture as a vital source of aquatic foods. However, rising costs and the limited availability of fishmeal in aquafeeds have spurred the search for alternative protein sources. While plant-based ingredients have been integrated into commercial aquafeeds, they come with challenges, including low protein content, palatability issues, and the presence of antinutritional factors. In this context, fish silage, derived from fish waste and discarded fish, stands out as a promising alternative technology due to its cost-effectiveness and sustainability attributes. The production of fish silage involves the addition of organic/inorganic acids or lactic acid bacteria to homogenized fish waste. This process yields a valuable mixture rich in peptides, free amino acids, and partially hydrolyzed proteins, offering significant nutritional benefits for animal diets. Beyond its nutritional advantages, fish silage contributes to environmental sustainability by reducing the impact of waste disposal and enhancing the value of fish waste. The objective of this review is to promote sustainable practices in the aquaculture industry in response to the increasing demand for high-quality feed nutrients. To achieve this, it includes an analysis of research results related to silage technology, an appraisal of the advantages and disadvantages of using fish silage as a feed additive, and a focus on emerging trends in this field.

Groundwater contamination by nitrate and organic chemicals (e.g. 1,4-dioxane) is a growing worldwide concern. This work presents a new approach for simultaneously treating nitrate and 1,4-dioxane, which is based on UV sensitization of nitrate and sulfite, and the production of reactive species. Specifically, water contaminated with nitrate and 1,4-dioxane is irradiated by a UV source (< 250 nm) at relatively high doses, to sensitize in-situ nitrate and generate HO•. This leads to the oxidation of 1,4-dioxane (and other organics), and the (undesired) production of nitrite as an intermediate. Subsequently, sulfite is added at an optimized time-point, and its UV sensitization produces hydrated electrons which reacts and reduces nitrite. Our results confirmed the effectivity of the proposed treatment: UV irradiation of nitrate (at > 5 mg N/L) efficiently degraded 1,4-dioxane, while producing nitrite at levels higher than 1 mg N/L (its MCL in drinking water). Adding sulfite to the process after 10 minutes of irradiation reduced the concentration of nitrite, without affecting the degradation rate of 1,4-dioxane. The treated water contained elevated levels of sulfate; albeit at much lower concentration than its MCL. Treating water contaminated with nitrate and organic chemicals (often detected concomitantly) typically requires several (expensive) treatment processes. The proposed approach may present a cost-effective alternative, employing a single system for the treatment of nitrate and organic contaminants

The valorization of the large amount of crude glycerol formed from biodiesel industry, is of primordial necessity. One possible direction with high interest to the biorefiniery sector is the production of fuel additives as solketal, though the acetalization of glycerol with acetone. This is a chemical process that conciliates high sustainability and economic interest, since solketal contributes to the fullfilment of a Circular Economy Model through its use in biodiesel blends. The key to guarantee high efficiency and high sustainability for solketal production is the use of a recovery and recyclable heterogeneous catalyst. Some examples are already reported in the literature (first example in 2012), and this review intends to conciliate the information spreaded in this topic and established the most important reacional parameters and the main catalytic characteristics strategies to achieve high solketal production in short reaction time.

Solid waste management in Accra is a major challenge to the Metropolitan Authorities and inhabitants. The rapidly increasing population coupled with poor capacity of the municipal and private waste management companies to management waste effectively has created issues of environmental concern. Due to poor waste managements systems, most household dispose waste indiscriminately leading to floods and health issues. The study showed that about 60% of household waste is organic materials which has the potential to be converted to compost for agriculture purpose. Meanwhile plastics and rubbers which litters the environment as well as blocking major storm drains and gutters hence creating huge environmental hazard is made of 11% of the total component of most household waste generated daily. The study also revealed that among the methods of disposing waste, dumping waste in skip containers located at authorized places was the preferred means of disposing waste by household though others also dispose waste by other means such as burying and burning. Inadequate skip containers per population of household in an area coupled with irregularity of tracks picking these containers makes skip containers dumping site ugly scene, hence creating health issues. Among the constraints that impact negatively on sustainable waste management in Accra Metropolis, economic constraints was perceived as the main challenge which affect efficient waste management. Currently the country is going through serious economic challenges so government does not release money timely to fund projects which waste management is key. Most donor partners that use to support the government with funds have either reduced or redrawn their services as they have no confidence in the state of Ghana economy. Aside the constrains, the study also indicated that factors such as poor public attitude towards waste management, poor enforcement of sanitation by-laws, inadequate and untimely release of government funds were also seen as the main factors affecting waste management.

The BIOTON® biochar, produced by a wood biomass pyrolysis process, usually applied as a soil amendment, was investigated for a novel application, i.e. the adsorption of lead from contaminated solutions. The experimental activity firstly included the physical-chemical characterization of BIOTON®; SEM images were also obtained to highlight its internal structure. The adsorption process was investigated through batch and column experiments. Adsorption kinetics showed a very rapid achievement of the equilibrium conditions, i.e. at 2h and 4h for 50 mg/L and 100 mg/L initial Pb concentration, respectively. Complete removal also occurred within the same time. The Brunauer–Emmett–Teller model better fitted the equilibrium data for both Pb concentrations, whereas the kinetics were best represented by the pseudo second order model. The column tests showed that the addition of biochar as adsorbent media within the bed significantly extended the time of breakthrough and exhaustion, with respect to the column filled with soil only. The adsorption capacities of BIOTON® versus lead solutions was found to be comparable to that reported for commercial adsorbents. Therefore, BIOTON® can be considered a valid option, with the additional benefit to reduce the environmental impact since allows to recover a residue which alternately would need to be disposed of.

Nowadays the preservation and restoration of historical building needs to be faced in accordance with a novel sensibility regarding environment to preserve the future generations. In this context, the scientific community is focusing on novel and sustainable materials and techniques allowing durability and mechanical performances and at the same time compatibility with the existing heritage. Alkali activated materials represent a great challenge to produce new materials starting from the existing ones with reducing consumption, emission of greenhouse gases and environmental impact. This study deals with the valorization of waste materials coming from demolition and construction activities in the manufacture of geocomposites suitable for restoration and conservation of historical heritage. In particular, waste from tuff sawing and brick grinding were used as raw materials, then the geopolymeric samples produced were characterized from physical-chemical and mechanical point of view in order to investigate their performance and evaluate their suitability as materials for historical buildings recovery. Brick waste based geocomposites resulted to be more compact than the tuff-based ones as showed by the higher density values and the lower values of open porosity and water absorption and as further confirmed by the trend of the mechanical performance. Moreover, experimental data showed that physical and mechanical properties of both bricks and tuff waste-based geocomposites, even with different waste content, are compatible with existing building materials and to all the traditional repairing products.

Cognitive impairment affects 34-65% of People with Multiple Sclerosis (PwMS), significantly impacting their quality of life. Clinicians routinely address cognitive deficits with in-clinic neuro-behavioural interventions, but accessibility issues exist. Telerehabilitation is a promising solution that utilises digital tools for home-based cognitive remediation. This narrative review assessed the feasibility and efficacy of cognitive telerehabilitation in PwMS, identifying 13 relevant studies. Regarding the feasibility of cognitive telerehabilitation, evidence shows adherence rates are generally good, although, surprisingly, not all studies reported a measure of compliance with the cognitive training explored. Considering the efficacy of different rehabilitative techniques on cognitive performance of PwMS, findings are generally inconsistent, with only one study reporting consistently positive results. A range of methodological limitations are reported as potential factors contributing to the variability of results. Overcoming some of these issues will be key. Upcoming research is necessary to determine optimal intervention approaches, long-term effects of rehabilitation, and how to best integrate the use of telerehabilitation into routine clinical practice. By exploiting digital tools in the best way and addressing methodological concerns, home-based rehabilitation holds the potential for improving cognitive functions and enhancing the quality of life in PwMS.

Heavy metals contamination in groundwater often occurs in various industrial processes. Stud-ies have confirmed that polysulfide could reduce hexavalent chromium to trivalent chromium, achieving the effect of in-situ stabilization. For other heavy metals contamination in groundwa-ter, whether polysulfide also had a stabilizing ability to achieve in-situ remediation. This re-search focused on heavy metals except for chromium that often contaminated in groundwater, including lead, nickel, zinc, copper, and cadmium to explore the feasibility of using calcium polysulfide (CaSx) as an in-situ stabilization technology for these heavy metals contamination groundwater. Results showed that CaSx had a great removal efficiency for heavy metals lead, nickel, zinc, copper, and cadmium. However, for nickel, zinc, copper and cadmium, when CaSx was added excessively, complexes would be formed, causing the result of re-dissolve and this would also reduce the removal efficiency. Since it is difficult to accurately control the dosage of agents for in-situ groundwater remediation, the concentration of re-dissolved nickel, zinc, cop-per, and cadmium may not be able to meet the groundwater control standards. CaSx had high lead removal efficiency, and it would not cause re-dissolution due to excessive CaSx dosing. CaSx can be used as an in-situ stabilization technique for lead contaminated groundwater.

Groundwater contamination is an ever-growing environmental issue that has attracted much and undiminished attention for the past half century. Groundwater contamination may originate from both anthropogenic (e.g., hydrocarbons) and natural compounds (e.g., nitrate and arsenic); to tackle the removal of these contaminants, different technologies have been developed and implemented. Recently, bioelectrochemical systems (BES) have emerged as a potential treatment for groundwater contamination, with reported in situ applications that showed promising results. Nitrate and hydrocarbons (toluene, phenanthrene, benzene, BTEX and light PAHs) have been successfully removed, due to the interaction of microbial metabolism with poised electrodes, in addition to physical migration due to the electric field generated in a BES. The selection of proper BESs relies on several factors and problems, such as the complexity of groundwater and subsoil environment, scale-up issues, and energy requirements that need to be accounted for. Modeling efforts could help predict case scenarios and select a proper design and approach, while BES-based biosensing could help monitoring remediation processes. In this review, we critically analyze in situ BES applications for groundwater remediation, focusing in particular on different proposed setups, and we identify and discuss the existing research gaps in the field.

Arsenic is naturally present in many geological formations around the world and is a major source of groundwater contamination. Bolivia is not exempt from this problem. Physical-chemical studies of water quality in deep and shallow wells have determined the presence of arsenic in some areas of the Bolivian Altiplano, valleys, and plains. In the Lake Poopó basin, water from shallow wells (up to 30 m) has arsenic concentrations that exceed the Bolivian drinking water standard and the WHO recommendation of 10 μg-As/l by up to 25 times. In peri-urban areas of Cochabamba, the arsenic content in groundwater is up to 113 μg-As/l. chronic exposure to arsenic is associated with neurological and dermatological problems and carcinogenic effects. To date, no measures have been taken to mitigate the arsenic problem for the rural population, who often rely on arsenic-contaminated water as their only source of drinking water. This contamination represents a serious threat to the health and economic well-being of the inhabitants and ecosystem in these areas. In this work, for arsenic removal, iron and iron oxide nanoparticles obtained from recycling metal chips by top-down and bottom-up technology have been used for arsenic adsorption in an experimental filter combined with other artisanal filtering materials in the form of layers. The results have shown that water contaminated with arsenic after passing through the filter reduces the concentration of total arsenic filtered from 83, 52 ppb to less than 5 ppb, less than the Bolivian standard 512 of 10 ppb for drinking water.

This comprehensive review explores recent advancements in heavy metal remediation techniques, focusing on the utilization of cellulose-silica composites and tailored surface modification techniques. We examine the synthesis strategies and properties of cellulose-silica adsorbents, highlighting their enhanced adsorption capacities and structural robustness for removing heavy metal pollutants from aqueous environments. The review investigates various surface modification approaches, including thiol-functionalization, amino acid grafting, and silane coupling agents, for optimizing the surface chemistry and morphology of cellulose-silica composites. Mechanistic insights into the adsorption processes and kinetics of modified adsorbents are discussed, along with considerations for optimizing adsorption performance under different environmental conditions. This review provides valuable perspectives on the development of effective adsorbent materials for sustainable heavy metal remediation applications.

This paper presents the results of investigations into the pyrolysis of waste polypropylene in a laboratory fixed-bed batch reactor. The experiments were designed and verified in such a way as to allow the application of the Response Surface Methodology (RSM) in the development of an empirical mathematical model that quantifies the impacts mentioned above. The influence of the mass of the raw material (50, 100 and 150 g), together with the reactor temperature (450, 475 and 500 °C) and the reaction time (45, 50 and 75 min) was examined. It has been shown that the mass of the raw material, i.e. the filling volume of the reactor, has a significant influence on the pyrolysis oil yield. This influence exceeds the influence of reactor temperature and reaction time. This was explained by observing the temperature change inside the reactor at three different spots at the bottom, middle and top of the reactor. Recorded temperature diagrams show that with greater masses of feedstock, local overheating occurs in the middle part of the reactor, which leads to overcracking of vapor products, and from there to an increased formation of non-condensable gases, i.e. reduced yield of pyrolytic oil.

Soil secondary salinization has seriously affected the greenhouse vegetable production in China. To improve the secondary salinization greenhouse soil and enhance the soil physical-chemical properties in an eco-environmental way, different organic amendments (straw, straw biochar, Trichoderma bio-organic manure, commercial organic manure) were applied using pot experiment for 60 day to comprehensively screen the optimal remediation method. In this study, soil nutrient condition and salt movement were assessed, and predictive models using multi-linear regression (MLR) and Random Forest (RF) were developed to estimate soil salinization parameters. The findings indicated a significant decrease in soil salt content following the application of organic materials compared to the control treatment. Specifically, the addition of straw at a rate of 250g/kg resulted in a 59.38% reduction in soil salt levels after 60 days (P < 0.05). Furthermore, the main salt ions exhibited dynamic changes over the course of the experiment, with reductions observed in Na+, Ca2+, Cl-, and NO3- content under the 250 g/kg straw treatment by 83.63%, 74.67%, 63.26%, 59.07%, respectively, compared to CK (P < 0.05). In addition, the SO42- content under 125 g/kg commercial organic manure amendment reduced by 48.94%, respectively (P < 0.05). Contrary to expectations, the addition of organic materials significantly increased the levels of total nutrients (N/P/K) and available potassium (AK) and phosphorus (AP) in the soil. Specifically, the addition of straw at a rate of 250 g/kg resulted in increases of 18.02%-87.38% in total potassium (TK), 66.67%-200% in total phosphorus (TP), and 142.87%-367.8% in AK after a period of sixty days (P < 0.05). Ultimately, the treatment involving the addition of 250 g/kg of straw demonstrated the most pronounced impact on the physical and chemical properties of the soil. The random forest method shows promise in accurately predicting soil salt and soil sodium adsorption ratio (SAR)indicators, thereby providing a valuable tool for estimating soil properties.

Colombia is the world's leading producer of mild washed arabica coffee and produces 12.6 million bags of green coffee, but at the same time 784,000 tons of waste biomass are dumped in open fields, of which only 5% is recovered or used. The objective of this project was to evaluate the production of platform chemicals from these coffee wastes. To achieve this, biomass characterization was carried out using proximate analysis, ultimate analysis and structural analysis. Hydrothermal valorization was carried out at a temperature range of 120-180 °C (LHW) and 180-260 °C (HTC) for one hour, the platform chemicals obtained were quantified by HPLC-IR, monitored by pH and conductivity, and the solid fraction was characterized by monitoring the functional groups in IR spectroscopy, and elemental analysis. Hydrolysis processes were obtained from 150 °C, production of platform chemicals from 180 °C and maximum concentration at 180 °C-4h, over 200 °C degradation of the products in the liquid fraction starts to take place. Homogeneous basic and acid catalysts were used to improve the yields of the reaction. The kinetics of the hydrolysis of lignocellulosic structures to sugars were also analyzed and described, and reaction orders of 1 (LHW), 3 (HTC) and their respective reaction rate equations were reported.

There is a need to find methods to intensify the anaerobic digestion process. One possibility is the use of pre-treatment techniques. Many laboratory tests confirm their effectiveness, but in most cases, there is no verification work carried out on industrial plants. The aim of the research carried out under laboratory conditions and on a large scale was to determine the technological and energy efficiency of the use of hydrodynamic cavitation in the pre-treatment of a waste mixture from dairy farms. It has been shown that hydrodynamic cavitation significantly increases the concentration of organic compounds in the dissolved phase. In the most effective variants, the increase in the content of these indicators was over 90% for both COD and TOC. The degree of solubilisation achieved was 49±2.6% for COD and almost 52±4.4% for TOC. Under laboratory conditions, the highest effects of anaerobic digestion were achieved after 10 minutes of pre-treatment. The amount of biogas was on average 367±18 mL/gCOD and the amount of methane 233±13 mL/gCOD. Further large-scale optimisation trials showed that after 8 minutes of hydrodynamic cavitation, the biogas yield was 327±8 L/kgCOD with a CH4 content of 62.9±1.9%. With this variant, the net energy yield was 66.4±2.6 kWh/day, a value that was 13.9% higher than the original variant with 10 minutes of disintegration and 3.1% higher than the variant without pre-treatment.

Additives can improve the efficiency of anaerobic digestion by increasing biogas production, reducing air pollution, and preventing total ammoniacal nitrogen (TAN) inhibition. Biological or chemical supplementation can also improve the economic efficiency of anaerobic digestion. However, the effects of specific additives on biogas production can vary depending on the type of supplement used. This research utilizes the additives on an industrial scale and monitors the optimization of the anaerobic digestion operating parameters after their addition. The various AD additives were examined in a sufficient cycle of operation for three biogas plants located in northern Greece. In this manner, the effectiveness was investigated in multiple initial feeds and unstable operating situations caused by the seasonality of specific feedstocks. The existing operation state in the three biogas plants was recorded before and after adding the supplements. In all three cases, lower concentration levels were observed in many of the examined trace elements. Introducing additives proved to be a stabilization factor in AD performance and inhibition mediator.

This paper examines the relationship between GDP per capita and waste generated in European Union countries, highlighting the importance of this relationship for understanding the environmental consequences of economic growth and formulating waste management policies. The analysis findings demonstrate that, in most cases, higher GDP is associated with higher amounts of waste, although there are exceptions to this trend. A smaller number of countries are also found where no such relationship exists. These are primarily high-income countries in the lower part of the EKC or countries in transition. Cluster analysis reveals regional differences in the relationship between GDP and waste that the economic factors and the level of development in the regions concerned can explain. Bulgaria is among the European countries with the lowest economic growth associated with a large amount of waste. The analysis, therefore, focuses on Bulgaria. The impact of GDP per capita, Human Development Index and Population Density on municipal waste in Bulgaria is studied. The aim is to identify significant relationships and dependencies between these factors and the amount of waste. Based on the results of multiple regression analysis and the findings from municipal waste management data in Bulgaria, specific actions are proposed for municipal waste management in the country. Recommendations are made for developing sustainable waste management policies and sharing best practices between regions.

The protection of all environmental compartments (water, soil, air) is of great interest for the normal functioning of life on Earth. Namely, the environment is systematically polluted with different concentrations of physical, biological and chemical pollutants. For the purpose of environmental protection, numerous in situ and ex situ biological, chemical and physical remediation techniques have been developed. Most techniques have limitations such as high costs, processing time and environmental feasibility. In general, biological techniques have proven to be the most environmentally friendly compared to chemical and physical techniques. Furthermore, remediation is an extremely complex procedure due to the complexity of the pollutant composition. Therefore, the implementation of individual physical, biological or chemical remediation techniques is often not sufficient for adequate remediation of the polluted environment. Accordingly, for more economical and efficient environmental remediation, it is recommended to use a combination of techniques that should meet the requirements of efficiency and treatment duration. Ultimately, this short review presents a concise overview of the recent application of physical, biological and chemical remediation techniques to all compartments of the polluted environment (water, air, soil). A critical review of existing knowledge on environmental remediation through a search of relevant literature helped to assess the basic challenges and limitations that arise in the issue of environmental remediation, as well as providing recommendations and guidelines for future research.

Ghana Tamale's current waste management system is overwhelmed by the growing waste crisis, necessitating the exploration of Waste-to-Energy technologies as an innovative solution. This study explores challenges and opportunities for integrating Waste-to-Energy (WtE) technologies into Tamale's existing waste management system. Qualitative research identified policy hurdles, financial constraints, social concerns, and institutional weaknesses as key barriers. Conversely, stakeholder collaboration, public education, and capacity building emerged as some success fac-tors. A proposed implementation plan emphasizes feasibility studies, public engagement, pub-lic-private partnerships (PPPs), and technology selection based on waste composition. Addition-ally, a novel framework for WtE integration within a broader Integrated Solid Waste Manage-ment (ISWM) system is presented. This framework incorporates waste sorting, recycling, WtE alternatives, and responsible management of residuals. Validation by key stakeholders con-firmed the framework's potential to improve waste management in Tamale. By overcoming identified challenges and implementing the proposed framework, Tamale can achieve environ-mental sustainability, energy generation, and progress towards UN SDGs 7, 11, and 12. This re-search offers valuable insights for policymakers and paves the way for a cleaner and more sus-tainable future for Tamale, potentially serving as a model for other developing cities.

Heavy metals are non-biodegradable and have a high toxicity effect to living things which makes their presence in the environment extremely dangerous. The method of handling heavy metals waste by photocatalysis techniques using TiO2/SiO2 composite showed a good performance in reducing harmful pollutants. In this study, SiO2 from Bengkulu beach sand was used as a support material for TiO2 photocatalyst to reduce Cr(VI) and Pb(II) concentrations. SiO2 was obtained through leaching techniques using NaOH as a solvent. The TiO2/SiO2 composite photocatalyst were synthesized using a solvothermal method at 130 °C and then characterized using XRD, FTIR, SEM and PSA. Based on the XRD diffractogram, the synthesized TiO2 showed the anatase structure while the SiO2 showed the amorphous structure. Ti-O-Si bond is defined in the IR spectra, which indicates that the relationship between TiO2 and SiO2 is a chemical interaction. The results of SEM and PSA characterizations show agglomerated spherical (round) particles with a mean particle size of 616.9 nm. The TiO2/SiO2 composite of 7:1 ratio showed the highest photocatalytic activity after 180 minutes of UV irradiation, with a concentration-decrease percentage of 93.77% and 93.55% for for Cr(VI) and Pb(II), respectively.

Plants have the ability to decrease the pollution level from the environment by absorbing inorganic/organic pollutants through their roots. After that, these pollutants are translocated or accumulated in less toxic forms in various parts of plants. This ability of plants is known as phytoremediation. It is an eco-friendly, and cost-effective approach for controlling environmental pollution. It can provide a sustainable way to improve the economics of developing countries. However, the biomass formed during this process can re-contaminate the environment through secondary pollutants. The contamination due to heavy metals (HMs) has become an environmental challenge globally. Metals such as cadmium (Cd), chromium (Cr), mercury (Hg), arsenic (As), nickel (Ni), lead (Pb), etc. can enter the water and soil largely through anthropogenic activities as well as other natural processes. After that, these metals pose a severe threat to living organisms. Due to their non-biodegradable nature, these metals can remain as such for a long time. These metals can initiate oxidative pressure in plants as a result affects agricultural production and yield. To mitigate this problem, phytoremediation has come forward as a safe, affordable, and ecologically sustainable solution than conventional physicochemical decontamination methods. Initially, several edible crops had been identified for the remediation. But at the present time, scientists are focusing on non-edible crops like aromatic/medicinal plants. There is no risk of food contamination by using these plants. This chapter describes the classification & uses of Tulsi and the phytoremediation mechanism of plants in detail.

Inadequately managed agricultural waste significantly impacts the environment, health, and economy. This form of pollution arises from the underutilization, poor awareness, and insufficient treatment of agricultural waste. Fruit and vegetable wastes are valuable sources of bioactive compounds. This study aims to revalorize discarded waste from red habanero chili peppers (Capsicum chinense) by extracting bioactive compounds through different extraction processes: maceration (ME), maceration assisted by ultrasound (US), Soxhlet extraction (SE), supercritical fluid extraction (SFE), and supercritical fluid extraction with a co-solvent (SFEC). Extraction processes have significant effects on extraction efficiency and phytochemical profile (capsaicinoids and carotenoids recovery). The results indicate that the highest efficiency process is obtained with SFEC, also a high phytochemicals recovery (14.9 mg of total capsaicinoids and total carotenoids 292.09 µg per gram of sample). Concerning to phytochemical profile in the extract, the maceration process gets the highest concentration of compound followed by US and SFEC. These data reveal that the use of SFE and SFEC extraction is recommended for extraction of phytochemicals with biologically activity from red habanero chili pepper waste for diverse industries application.

This study aims to explain individual engagement in sustainable waste management behaviors (SWMBs) based on the application of protection motivation theory (PMT). SWMBs include waste avoidance, green purchasing behavior, reuse and recycle, and waste disposal behaviors. This study applies PMT to explore how individuals’ SWMBs are influenced by their perceived threats caused by environmental contamination from waste disposal and their perceived coping capability. The Bangkok metropolitan area was selected as a case study because it has faced serious waste management problems caused by massively increasing amounts of solid waste during the last ten years. Questionnaire surveys were conducted with 193 public and private officers residing in the city of Bangkok. The one-way analysis of variance (ANOVA) was performed to justify the effect of individual threat appraisal and coping appraisal on the engagement in SWMBs. The results demonstrated that respondents’ self-efficacy highly influenced all types of SWMBs. The perceived probability of being impacted from pollutants influenced all of the SWMBs except green purchasing behaviors. Response efficacy did not influence all SWMBs; however, the perceived severity of adverse consequences caused by pollutants highly influenced reuse and recycle behaviors. It could be suggested that PMT is well suited for investigating low-cost and simple SWMBs. It could also be suggested that different communication campaigns should be established to enhance citizens’ engagement in each type of SWMB.

Singapore, being a land-scarce country, is heavily dependent on imported food, which poses a challenge in ensuring food security. In addition, the substantial amount of food waste generated in Singapore further deepens food insecurity challenges, imposing enormous pressure on the country's food and land resources. In the recent years, valorising food waste streams into higher value products has been an increasing trend in tackling food wastage due to its economical and environmental benefits. This paper provides a thorough review on food waste valorisation in Singapore and summarizes critical information from the current food landscape to the food waste management strategies adopted. The review highlights the prototypes developed from food waste streams by the local research and development capabilities and the technological processing and techniques used for versatile applications ranging from food and nutraceuticals to urban agriculture. The challenges associated with the valorisation of food waste are also addressed. Two ambitious Initiatives by the Singapore government Zero Waste Plan and the 30-by-30 food security goal to encourage food waste valorisation are explored and presented. The review serves as a reference for other countries in ensuring food security and achieving sustainable development goals.

Waste-to-Hydrogen (Wahh) is a process of converting waste into hydrogen gas through various methods such as thermal conversion, biological conversion, and chemical conversion. This process not only helps in managing waste but also provides a clean source of energy as hydrogen is a renewable energy source that produces zero greenhouse gas emissions during combustion. Wahh has the potential to provide a sustainable solution for energy generation and waste management in the current scenario of globally increasing energy demands. This study aims to examine the properties and energy efficiencies of various renewable fuels including fuelwood, biogas, biomethane, and biohydrogen with a specific focus on differentiating the characteristics of biohydrogen. The paper explores the emerging concepts of waste-to-hydrogen microgrids, biohydrogen refineries, biohydrogen prosumer networks, and a biohydrogen circular economy, as well as Public-Private-People Partnerships (4Ps) and the hydrogen-centric renewable energy revolution, which are taking shape in industrialized countries. The study presents a comprehensive feasibility analysis of these concepts in the context of Nepal. The results of this research will provide valuable insights into the potential for adopting these innovative technologies in Nepal and will contribute to the development of a sustainable and efficient energy system.

Depression is diagnosed when a specific set of symptoms appear over a defined period with a certain intensity. According to the DSM-5, Major Depressive Disorder (MDD) is diagnosed when five or more symptoms are present over a two-week period. Depression, a debilitating mental health disorder affecting millions worldwide, poses a complex challenge for researchers and clinicians. In children and adolescents, depression can result in negative outcomes such as substance abuse, academic problems, risky sexual behavior, physical health issues, impaired social relationships, and a thirty-fold increased risk of suicide. This paper presents the findings of a study that evaluated the effectiveness of Cognitive Behavioral Therapy (CBT) alone and CBT combined with selective ser-otonin reuptake inhibitors (SSRIs) in a remediation program. The study included 16 children and adolescents with depression (8 males and 8 females) and 16 typically developing peers (8 males and 8 females) aged 9 to 15 years (M = 11.94, SD = 2.02). Baseline evaluations using Event-Related Po-tentials (ERPs), the Children Depression Inventory (CDI), and reaction time tests showed that participants with depression had cognitive deficits in attention and memory, indicated by longer P300 latencies. After undergoing remediation with either CBT alone or CBT combined with med-ication, the children and adolescents with depression exhibited lower CDI scores and shorter P300 latencies and reaction times compared to before remediation and relative to the control group.

Cutting-edge technologies are intensifying into new skylines and this remarkable progress has been successfully influenced by the tiny level engineering of carbon dots technology, their syn-thesis advancement and impressive applications in the field of allied sciences. The advances of science and its conjugation with interdisciplinary fields emerged in carbon dots making, their controlled characterization and applications into faster, cheaper as well as more reliable prod-ucts in various scientific domains. Thus, a new era in nanotechnology has developed into carbon dots technology. The understanding of the generation process, control on making processes and selected applications of carbon dots such as energy storage, environmental monitoring, catalysis, contaminates detections and complex environmental forensics, drug delivery, drug targeting and other biomedical applications etc. are among the most promising applications of carbon dots and thus a thrust area of research today. In this regard, various types of carbon dots nano-materials such as oxides, their composites and conjugations etc. have been flocking significant attention due to their remarkable potential in this thrust area of energy, the environment and technology. Thus, the present paper highlights the role and importance of carbon dots, recent advancements in their synthesis methods, properties and emerging applications.

Currently, there is a tenacious need to find new ways to purify water by eliminating bacterial biofilms, textile dyes, and toxic water pollutants. These contaminants pose significant risks to both human health and the environment. To address this issue, in this study, we have developed an eco-friendly approach that involves synthesizing Cobalt-doped Cerium Iron Oxide (CCIO) nanocomposite (NC) using an aqueous extract of Gossypium arboreum L. stalks. The resulting nanoparticles can be used to effectively purify water and tackle the challenges associated with these harmful pollutants. Nanoparticles excel in water pollutant removal by providing high surface area for efficient adsorption, versatile design for simultaneous removal of multiple contaminants, catalytic properties for organic pollutant degradation, and magnetic features for easy separation, offering cost-effective and sustainable water treatment solutions. CCIO nanocomposite has been synthesized by green co-precipitation method due to biomolecules and co-enzymes present in the aqueous extract of Gossypium arboreum L. stalk; a single-step procedure completed in 5 h reaction time. Further, the synthesis of nanocomposites was confirmed by various characterization techniques such as Fourier-transform infrared (FT-IR) spectroscopy, X-ray diffraction (XRD), Field emission scanning electron microscopy (FE-SEM), Transmission electron microscopy (TEM), Thermogravimetric analysis (TGA), Dynamic light scattering (DLS), and Energy Dispersive X-Ray (EDX). CCIO NCs were discovered to have a spherical shape and an average size of 40 nm. Based on DLS zeta potential analysis, CCIO NCs were found to be anionic. Also, CCIO NCs showed significant antimicrobial and antioxidant activity. Overall, considering the physical and chemical properties, the application of CCIO NCs in the adsorption of various dyes (~91 %) and water pollutants (chromium = ~ 60 %) has been considered since they exhibit great adsorption capacity owing to their microporous structure which can be a step forward in water purification.

Within the past few decades, thousands of experiments have been performed to characterize waste and biomass to estimate the bioenergy potential and product identification. There is a need to develop an integrated process model based on experimental literature, and simulation to obtain suitable products. In this study municipal solid waste (MSW) characterization and integrated process model have been developed to optimize final products in a reactor system. The process model has two modes R&amp;D and reactor control (RC) to obtain suitable products including bio-oil, char, and gases. A database was integrated based on thermokinetics, machine learning and simulation models to optimize product efficiency. The experimental data includes thermogravimetric analysis, Fourier transform Infrared Spectroscopy, Gas chromatography, and Mass spectrometry, which are linked with pyrolysis experimental setup. Feedstock-product mapping models were incorporated into the database along with the temperature, heating rates, elemental analysis, and final product concentration, which are utilized for pyrolysis reactor setup. Product feasibility is conducted based on lifecycle cost, affordability, and product efficiency. The present work will bridge the gap between experimental study and decision making based on obtained products at several experimental conditions around the world.

Soil washing is a rapid and efficient method for heavy metals removal. In this study, in order to prove the feasibility of leaching remediation technology for remediation of lead-contaminated soil around a smelter, intermittent oscillating washing tests and extensive continuous tests were conducted to remediate Pb contaminated soils. Plant growth tests with wheat (Bainong Aikang 58) were also conducted to investigate the effects of leaching on plant growth and the Pb content of stems and leaves. The results revealed that in soils, Pb mainly exists in the forms of PbCO3, Pb5(PO4)3Cl2, PbSO4, and in small amounts of PbS. The intermittent oscillating washing tests showed that a lower liquidsolid(L/S) ratio and a higher leaching temperature and time were related to increased Pb removal efficiency. The Pb removal efficiency rates in the oscillating washing tests and the extensive continuous tests were 72.50% and 69.94%, respectively. In addition, the chemical and physical characteristics of the soil were basically unchanged after the leaching regimes. The results of the plant growth tests showed that the leaching regimes did not have a negative effect on the survival rate and growth of the wheat, and the heavy metal contents of the stem and leaf were effectively reduced. This study provides a reference for the large-scale remediation of contaminated soils.

Water pollution is the main problem in the current scenario which is being faced by mankind due to the industrial and commercial effects. Industrial effluents contain heavy metals and inorganic ions like nitrates and phosphate ions. These ions are being included in waterways through industrial runoff. When the concentration of these hazardous pollutants increases in aquatic flora and fauna causes severe health problems. So remediation of these toxicants from water reserves is of chief importance. Conventional processes along with modern processes are being used for the treatment of industrial wastes. Photo-degradation is a modern method used for the degradation of inorganic ions due to its environmentally friendly nature and cost-effectiveness. In a recent study Aluminum oxide (Al2O3) nanoparticles were synthesized via a green approach at different pH by using Cymbopogan citratus (lemongrass) plant extract and these nanoparticles were used for the removal of inorganic ions from wastewater. The nanoparticles of different pH showed different % degradation of the inorganic ions in acidic medium removal of inorganic waste was less, in basic media % degradation was more as compared to acidic media but maximum % degradation was observed in neutral media like that average % degradation 91% and 81% was observed for nitrate and phosphate ions. The maximum absorbance occurred at 212nm and Al2O3 nanoparticles showed absorbance from 210nm-217nm. The R2 values of pseudo1st, 2nd, and BMG models were 0.956, 0.837, 0.7007 0.95, 0.896, and 0.756 for the nitrate and phosphate ions. Characterizations of synthesized particles were investigated by using UV-visible spectroscopy and other analytical methods like X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). The statistical analyses were done using Simple Linear regression (SLR).

Sharing the same raw material, recycling and composting are in direct conflict with incineration of municipal solid waste in combined heath and power plants. Indeed, waste-to-energy plants in regions with high recycling rates import urban waste from other countries to use otherwise unused capacity, and raise revenues. Using the case of Italy’s second largest and economically most developed region, I discuss the economic viability of municipal solid waste incineration to produce electricity and heath in the context of the increasing role of electricity production from renewable energy sources as well as of the emerging mass-scale uptake of bioplastics. Four lessons and three guidelines aimed to local authorities and policy makers emerge from the present study.

The river Teign in Devon has come under scrutiny for failing to meet Environmental Quality Standards for ecotoxic metals due to past mining operations. A disused mine known as Bridford Barytes mine, has been found to contribute a significant source of Zn, Cd and Pb to the river. Recently, studies have been focused on the remediation of such mine sites using low-cost treatment methods to help reduce metal loads to the river downstream. Red mud is a waste product from the aluminium industry, the utilization of this resource has proven an attractive low-cost treatment method for adsorbing toxic metals. Adsorption kinetics and capacity experiments reveal metal removal efficiencies of up to 70% within the first 2 hours when red mud is applied in pelletized form. Biochar is another effective adsorbent with the potential to remove >90% Zn using agricultural feedstock. Compliance of the Teign has been investigated by analysing dissolved metal concentrations and bioavailable fractions of Zn to assess if levels are of environmental concern. By applying a Real-World Application Model, this study reveals that compressed pellets and agricultural biochar offer an effective, low-cost option to reducing metal concentrations and thus improving the quality of the river Teign.

The global food system has three recognized challenges: (a)increasing the availability of food consumption, (b) reducing food loss, and (c) reducing food waste. The increasing demand for food consumption, increasing quantity of food loss, and corresponding increase in food waste are resulting in serious health, aesthetic, social, economic, and environmental problems due to a lack of appropriate planning and management. Despite its importance, there is no clear, concise, and comprehensive definition of food consumption, loss, and waste. Generally, food consumption, food loss, and food waste are dealt with separately. This article presents a logically constructed ontological framework of food consumption, loss, and waste. It gives equal importance to all three aspects of global food management. The systematic ontological framework is general, and the analysis can be applied to any country. The framework deconstructs the combinatorial complexity of the problem and explicates the pathways to manage the consumption, loss, and waste. The ontological framework encapsulates 19*8*7*4*5*6 = 25,536 possible components of the challenge. A critical analysis based on available data using the framework will help to develop strategies to deal with the problem. It can help to discover the gaps and to find ways to bridge the gaps. It is novel to conceptualize food consumption, loss, and waste together.

The city of Lisbon, has any other capital of a European country, has a large number of issues while managing the waste and recycling containers spread throughout the city. This document presents the results of a study promoted by the Lisbon City Council for trialing LPWAN technology on the waste management vertical under the Lisbon Smart City initiative. Current waste management is done using GSM sensors, and the aim is to use LPWAN to reduce the costs, improve range and reduce provisioning times when changing the communications provider. After an initial study, LoRa was selected as the LPWAN of choice for the trials. The study is composed of multiple use cases at different distances, types of recycling waste containers, placements (underground and surface) and different kinds of waste level measurement LoRa sensors, deployed in order to assess the impact of the different use cases on the LoRa sensor usage. The results shown that the underground waste containers present the most difficult challenge, where the container itself imposes attenuation levels of 26dB on the link budget. The results promoted the deployment of a city wide LoRa network available to all departments inside the Lisbon City Council, and considering the network capacity the network, the network is also available to citizens to be used freely.

Valorization of food and fruit wastes has the potential for the production of sustainable energy and biochemicals. Approximately 70% of the weight of the original jackfruit (Artocarpus heterophyllus L.) fruit is lost during processing as waste in the form of peeled skin and core, both of which have not been utilized and, thus contribute to disposal as well as pollution issues. The major components, cellulose, and hemicellulose, can be biologically transformed easily into bioenergy sources like ethanol, methanol, and butanol; valuable phenolics and biotechnological products like pectin, citric acid, bromelain, ferulic acid, and vanillin; and many other products. These residues can also be utilized as essential sources for the biological transformation process leading to the production of numerous products with added value, such as phenolic antioxidants, phenolic flavor compounds, and organic acids. Thus, the value addition of jackfruit waste can support the sustainable solution towards food and nutritional security. In this way, zero waste can be achieved through novel biorefineries which are critically highlighted in this paper. Furthermore, novel technologies for the conversion of jackfruit wastes are summarized with recent findings.

This study examines the recovery efforts at Gran Tarajal Harbor following a significant oil spill, employing innovative technologies. Initial response efforts were hampered by inadequate contingency plans and bureaucratic delays, underscoring the need for improved preparedness. Cleanup operations utilized advanced methods such as enhanced absorbent sponges, absorbent granulates, bioremediation with allochthonous species, and a combination of barriers and sponges. These technologies proved effective in minimizing environmental impact, reducing hydrocarbon concentrations in sediments from nearly 60,000 mg/kg to less than 1,600 mg/kg in seven months. Heavy metal analysis revealed lead and copper concentrations associated as well as with routine port activities, while mercury levels linked to the spill decreased over time. Tissue analysis indicated minimal contamination in local organisms, suggesting limited impact from the spill, and evaluation of the biological communities in sediments suggest an ecological recovery. Study underscores the importance of rapid response, advanced technologies, and detailed contingency plans tailored to each port. Despite the successful cleanup and ecosystem recovery, political and bureaucratic challenges remain significant obstacles to implementing these improved methods. The findings advocate for a re-evaluation of current oil spill response protocols to incorporate more effective, sustainable, and cost-efficient technologies, aligning with the principles of a circular economy.

The immobilisation of bacteria on biochar has shown potential for enhanced remediation of petroleum hydrocarbon-contaminated soil. However, there is a lack of knowledge on the effect of bacterial immobilisation on biosolids-derived biochar for the remediation of diesel-contaminated soil. The aim of this current study was to assess the impact of the immobilisation on biosolids-derived biochar of an autochthonous hydrocarbonoclastic bacteria, Ochrobacterium sp. (BIB) on the remediation of diesel-contaminated soil using a laboratory based mesocosm study. Additionally, the effect of fertiliser application on the efficacy of the BIB treatment was investigated. Biochar (BC) application alone led to significantly higher hydrocarbon removal compared to the control treatment at all sampling times (4,887 – 11,589 mg/kg higher). When Ochrobacterium sp. was immobilised on biochar (BIB), the hydrocarbon removal was higher than BC by 5,533 mg/kg and 1,607 mg/kg at weeks 10 and 22, respectively. However, when BIB was co-applied with fertiliser (BIBF), the hydrocarbon removal was lower than BIB by 6,987 – 11,767 mg/kg. Quantitative PCR analysis revealed that the gene related to Ochrobacterium sp. was higher in BIB than in the BC treatment, which likely contributed to higher hydrocarbon removal in the BIB treatment. The findings of this study demonstrate that bacteria immobilisation on biosolids-derived biochar is a promising technique for the remediation of diesel-contaminated soil. Future studies should focus on optimising the immobilisation process for enhanced hydrocarbon removal.

Solid waste management is a global issue that affects every individual living in the world directly or indirectly. Failing to manage the waste properly will cause harm on public health, our natural environment, and even our happiness and prosperity. When asked about the reason behind the failure of third time plastic ban in Bhutan, one of the Bhutanese said it’s because of the lack of cooperation from public to support the move of government. Clean Bhutan, a non-governmental organization (NGO) that aims Zero Waste Bhutan by 2030, has collected around 5,900 metric tons of waste from December 2014 to February 2018. This project will create some awareness regarding the management of waste at individual level when people come in contact with the family of the researcher. It also talks abot how waste management and biodiversity conservation can go side by side.

This scoping review examines global strategies and enterprises for sustainable solid waste management, with a focus on alternative landfilling approaches. The study collected and analyzed a significant number of documents from different regions, revealing Asia as the major contributor (for the collected documents) (48.7%), followed by North America (24.3%) and Europe (15.8%). Recycling emerged as the most effective alternative waste treatment method, representing 52.3% of the documented approaches, with industrial recycling (22.6%) and residential/non-residential recycling (20.2%) as prominent categories. Food waste was a significant concern across regions, constituting 21.4% of the collected documents. Composting was widely adopted (15.4%) due to its simplicity and benefits for gardening and soil improvement. Other methods like biogas extraction, reusing, raising awareness, incinerating, redistributing, reducing, and fermentation accounted for 13.1% cumulatively. The study highlights the need for tailored waste management solutions based on regional challenges and successful practices. Promoting recycling infrastructure, composting, and waste reduction approaches are crucial to achieving sustainable waste management aligned with SDGs. Collaboration and knowledge-sharing between regions are essential to improve inefficient waste management mechanisms. Integrating the findings into policymaking and industry practices can lead to a more sustainable future with reduced environmental impact.

The proof-of-the-concept of application of low-temperature food waste biochars for the anaerobic digestion (AD) of food waste (the same substrate) was tested. The concept assumes that residual heat from biogas utilization may be reused for biochar production. Four low-temperature biochars produced under two pyrolytic temperatures 300 °C and 400 °C and under atmospheric and 15 bars pressure with 60 minutes retention time were used. Additionally, the biochar produced during hydrothermal carbonization (HTC) was tested. The work studied the effect of a low biochar dose (0.05 gBC x gTSsubstrate-1, or 0.65 gBC x L-1) on AD batch reactors’ performance. The biochemical methane potential test took 21 days and the process kinetics using the first-order model were determined. The results showed that biochars obtained under 400°C with atmospheric pressure and under HTC conditions improve methane yield by 3.6%. It has been revealed that thermochemical pressure influences the electrical conductivity of biochars. The biomethane was produced with a rate (k) of 0.24 d-1, and the most effective biochars increased the biodegradability of FW to 81% in comparison to variants without biochars (75%).

Tributyltin (TBT) is one of the most toxic anthropogenic compounds introduced into the marine environment. Despite its global ban in 2008, TBT is still a problem of great concern due to its high affinity for particulate matter, providing a direct and potentially persistent route of entry into benthic sediments. Bioremediation strategies may constitute an alternative approach to conventional physicochemical methods, benefiting from the microorganism’s potential to metabolize anthropogenic compounds. In this work, a simple, precise and accurate static headspace gas chromatography method was developed to investigate the ability of TBT degrading microbes in sedimentary microcosms over a period of 120 days. The proposed method was validated for linearity, repeatability, accuracy, specificity, limit of detection and limit of quantification. The method was subsequently successfully applied for the detection and quantification of TBT and degrading compounds in sediment samples on day 0, 30, 60, 90 and 120 of the experiment employing the principles of green chemistry. On day 120 the concentration of TBT remaining in the microcosms ranged between 91.91 ng/g wet wt for the least effective microbial inoculant to 52.73 ng/g wet wt for the most effective microbial inoculant from a stating concentration of 100 ng/g wet wt.

The removal of methylene blue (MB) dye from water was investigated using synthetic nano-clay magadiite (SNCM). SNCM was synthesized by hydrothermal treatment under autogenous pressure. A rosette-shaped single mesoporous magadiite phase with 16.63 nm average crystallite size and 33 m².g^-1 BET-surface area was recorded. The adsorption results indicated the pronounced affinity of the SNCM to the MB dye molecules which reached adsorption uptake of 20.0 mg MB dye/g of SNCM. The elimination of MB dye by the SNCM was kinetically and thermodynamically considered; a pseudo second order kinetic model was attained, and a spontaneous, chemical, and exothermic in nature was verified.

As the additive manufacturing industry grows, it is compounding the global plastic waste problem. Distributed recycling and additive manufacturing (DRAM) offers an economic solution to this challenge, but it has been relegated to either small-volume 3D printers (limiting waste recycling throughput) or expensive industrial machines (limiting accessibility and lateral scaling). To overcome these challenges, this paper provides proof-of-concept for a novel open-source hybrid 3D printer that combines a low-cost hanging printer design with a compression screw-based end-effector that allows direct extrusion of recycled plastic waste in large expandable printing volumes. Mechanical testing of the resultant prints from 100% waste plastic, however, showed that combining challenges of non-uniform feedstocks and a heavy printhead for a hangprinter reduced the strength of the parts compared to fused filament fabrication. The preliminary results are technologically promising, however, and provide opportunities to improve on the open source design to help process the volumes of waste plastic needed for DRAM to address the negative environmental impacts of global plastic use.

Abstract: In order to accelerate deployment of distributed recycling by providing low-cost feed stocks of granulated post-consumer waste plastic, this study analyzes an open source waste plastic granulator system. It is designed, built and tested for its ability to convert post-consumer waste, 3-D printed products and waste into polymer feedstock for recyclebots of fused particle/granule printers. The technical specifications of the device are quantified in terms of power consumption (380 to 404W for PET and PLA, respectively) and particle size distribution. The open source device can be fabricated for less than USD$2000 in materials. The experimentally-measured power use is only a minor contribution to the overall embodied energy of distributed recycling of waste plastic. The resultant plastic particle size distributions were found to be appropriate for use in both recyclebots and direct material extrusion 3-D printers. Simple retrofits are shown to reduce sound levels during operation by 4dB-5dB for the vacuum. These results indicate that the open source waste plastic granulator is an appropriate technology for community, library, makespace, fab lab or small business-based distributed recycling.

This study aimed to investigate the effect of reducing the amount of organic waste on the weight of cats in Tehran. The weight of 4192 cats was measured from spring 2016 to the end of winter 2020. They were classified into 6 age groups, 2 gender groups, and 13 geographical areas. Their weight was measured for 48 months (16 seasons). The statistical parameters analysis showed no weight loss in 2017, but since 2018, cats have been losing weight every year. They had lost about 178g of their weight in 2018. The sharpest annual decrease was observed in 2019 when about 301g of weight loss was recorded. In the winter of 2020, 115g of weight loss took place. In the spring of 2017, no weight change was observed, but in the spring of 2018, the cats lost 155g of their weight. Their weight loss intensified in the spring of 2019 and about 299g of weight loss was observed. In the summer of 2017, as in the spring of the same year, no weight loss was recorded, but for the summer of 2018, the weight loss was evident and about 205g of the weight of the cats had been reduced. The weight loss in the summer of 2019 not only continued but intensified and about 304g of weight loss was recorded for cats. Weight change was not observed in the fall of 2017 as in the spring and summer of the same year. In the fall of 2018, weight loss was recorded for cats. They had lost about 324g of their weight in the fall of 2018. Also, they experienced a weight loss of about 218g in the fall of 2019. During the spring, summer, and autumn of 2017, no weight loss was observed in the cats for the winter of 2018, but in the winter of 2019, the cats faced the most severe weight loss (seasonally). They lost about 401g of weight in the winter of 2019. Of course, in the winter of 2020, about 186g of weight loss was observed in cats. The results showed that female cats did not lose weight in 2017 but experienced weight loss in 2018 with a weight loss of 181g. The weight loss of females intensified in 2019 and 294g of weight loss was recorded. Female cats lost 186g of their weight in the winter of 2020. Male cats did not lose weight like female cats in 2017. But in 2018, a weight loss of 166g was observed in male cats. The weight loss of male cats continued in 2019 and 311g of weight loss was recorded for them. However, in 2020, unlike females, weight loss was not observed in male cats. It can be said that both sexes lost more weight in the winter of 2019 than in other seasons. In 2017, weight loss was observed only for the region of 10, and in the same year, weight gain was recorded for the region of 15. But in 2018, except for regions 3, 4, 15, and 19, weight loss was observed in other regions. In 2019, the weight loss of cats spread and weight loss was observed in all regions except the region of 12. In winter 2020, weight loss was recorded only in the region of 4. In the end, it can be concluded that the weight of cats has decreased since the spring of 2018 because the beginning of the decrease in the amount of organic waste has been recorded since the winter of 2018. So, there is a direct relationship between the weight of cats and the amount of organic waste (access to food). The amount of garbage has been decreasing since the winter of 2018, and the average weight of cats has also been decreasing since the spring of 2018 due to the decrease in access to food.

The issue of sustainability has long been the subject of interest of the architecture engineering and construction sector. All three aspects of sustainability - economic, environmental and social - can be affected through appropriate construction waste management. Construction and demolition waste (CDW) is one of the largest worldwide waste streams, therefore it is given great attention by all stakeholders (investors, contractors, authorities, etc.). Researches have shown that one of the main barriers to insufficiency CDW recovery is inadequate policies and legal frameworks to manage CDW. It is also one of the EU's environmental priorities. Aim of the article is to confirm the economic potential of construction and demolition waste audit processing through case study. A pre-demolition waste audit has been processed for unused building of shopping center in the town Snina in Slovakia. Subsequently, a comparison of economic parameters (waste disposal costs and transport costs) of recommended CDW management was performed. This comparison confirmed the economic benefits of environmentally friendly construction waste management methods according to the waste audit results, which will also increase the sustainability of construction projects. In addition, the cost parameters of selected waste disposal methods could be another dimension of building information modelling.

There are various approaches to managing polyethylene terephthalate waste, including methods for recycling PET. However, at present, only the cleanest wastes that can already be efficiently recycled using known methods are considered in the scientific literature. The study aims to look at other forms of polyethylene terephthalate waste that pose a challenge: low quality PET flakes, polyester tire cord, PET dust and prepolymer waste. The waste was characterized by FTIR spectroscopy, viscosimetry, differential scanning calorimetry, laser diffraction and sieve analysis. The findings describe the composition and properties of various forms of polyethylene terephthalate waste. Low quality PET flake waste and polyethylene terephthalate dust have been shown to be suitable for all chemical recycling methods. When recycling waste polyester tire cord, it is difficult to completely separate the rubber, so its presence in the final product must be taken into account. The most promising way to process a prepolymer is its depolymerization by hydrolysis, alcoholysis or glycolysis to produce monomers for the synthesis of PET, similar in properties to the primary one.

The consistent and continuous growth in the world’s population is creating many challenges for public policymakers in the different life areas, including dealing with the increasing amounts of waste that are generating problems involving air and land pollution and a shortage of land for waste disposal. This study presents the results of public policy on managing municipal waste, as manifested in the quantity and rate of waste collected throughout Israel in recent years and disposed of in the various landfills and in analysis of the political and economic factors affecting this policy. The study combines a quantitative and qualitative approach, where the quantitative study includes analysis of statistical data based on information from the Central Bureau of Statistics, the Ministry of Environmental Protection, the Ministry of Finance, and others, and the qualitative study relies on reading and analyzing primary documents of the different government ministries on Israel’s waste disposal policy and information in the media on this issue. The research findings attest to an increase in the amount of municipal waste dumped in Israel, a merely slight decrease in the rate of landfilling as a proportion of all municipal waste disposal, and a merely slight increase in the rate of municipal waste recycled in recent years. The research conclusions stress the effects of the landfill levy and the Cleanliness Maintenance Fund on one hand, and of the government instability in the Ministry of Environmental Protection, the positivist policy embraced by decision makers in the Ministry of Environmental Protection, and the power struggles between Israel’s different ministries on the other, as the respective economic and political factors affecting Israeli policy on municipal waste management.

The treatment, disposal, and resource utilization of waste mud are challenges for engineering construction. This study investigates the road performance of waste mud–solidified soil and reveals the mechanism of how solidifying materials influence the strength and deformation characteristics of waste mud. Waste mud, collected from a highway reconstruction project, was mixed with ordinary Portland cement as a solidifying material. Unconfined compressive strength tests, consolidated undrained triaxial shear tests, resonant column tests, and consolidation compression tests were conducted to evaluate the solidification effect. The test results show that with an increase in cement content from 5% to 9%, the unconfined compressive strength of the waste mud–solidified soil increased by over 100%, the curing time was extended from 3 days to 28 days, and the unconfined compressive strength increased by approximately 70%. However, an increase in initial water content from 40% to 60% reduced the unconfined compressive strength by 50%. With the increase of cement content from 5% to 9%, the cohesion and friction angles increased by approximately 78% and 24%, respectively. The initial shear modulus under dynamic shear increased by approximately 38% and the shear strain corresponding to a damping ratio decay to 70% of the initial shear modulus decreased by nearly 11%. The compression coefficient decreased by approximately 55%. Scanning electron microscopy and X-ray diffraction tests showed that a higher cement content led to the formation of more hydration reaction products, especially an increase in the content of AlPO4. The bonding material between soil particles significantly increased, exerting a bonding and filling effect on soil particles and firmly adhering them together. Consequently, the strength of the waste mud–solidified soil increased significantly while its compressibility decreased.

The article provides an overview of nanocomposites and microelectronic elements used in space electronics and radiation control systems of nuclear reactors. Only those nanocomposites and microelectronic elements are taken into account that improve their characteristics in radiation fields or remain indifferent when exposed to ionizing radiation. Considering the chemical composition of the materials of these nanocomposites and microelectronic elements, it is analyzed from which radioactive materials (RM) obtained by recycling radioactive waste (RW) such composites and microelectronic parts can be made. Thus, an alternative way of radioactive waste disposal is proposed, when these wastes are used in the form of microelectronic elements designed to operate under conditions of cosmic radiation.

Introduction: Pharmaceutical products are inevitable for human health. Owing to the growing need for pharmaceuticals, pharmaceutical companies introduce drugs annually into the market in addition to the extensive collection of existing pharmaceutical products. Households, farms, health facilities, and pharmaceutical industries release pharmaceutical waste into the environment at low concentrations through routine pharmaceutical use, damage, and expiry. The effects of active pharmaceutical ingredients (API) on non-target species in the environment are not known. Over the years, pharmaceuticals such as diclofenac and ibuprofen in trace amounts have been detected in public water systems, ground and surface water. Unwanted medicines should be safely disposed of at a reduced financial cost to mitigate the public and environmental health risks. Lack of general knowledge of how to dispose of unused pharmaceuticals leads to improper disposal resulting in accidental toxicity, rising healthcare costs, landfills pilfering/scavenging, water supply pollution, anti-microbial resistance, and death. To mitigate such effects, pharmacists should raise public awareness about safe disposal practices. Objective: This review aims to examine the sources of pharmaceutical waste, disposal costs, secure disposal methods, the effects of inappropriate disposal, and the role of pharmacists in the disposal. Method: The information on the stated objectives was gathered from available sources through a comprehensive literature review. Conclusion: Many countries contain tons of pharmaceutical waste that are expensive to destroy. Because of improper disposal, pharmaceutical waste has been found at trace amounts in drinking and surface water. A practical, environmentally sustainable approach to pharmaceutical waste management, with policies and guidelines, and public awareness campaigns, are necessary to address the problem of safe waste disposal. The national drug regulatory bodies should conduct environmental risk assessment resulting from the disposal of unwanted pharmaceuticals. Pharmacists should facilitate extensive training on sustainable drug use and proper pharmaceutical waste disposal at all levels to reduce the risks associated with improper disposal. Reduction of pharmaceutical waste generation at each step of a drug’s lifecycle, implementing takeback options, collection at approved sites, and modern technology to treat wastewater are highly recommended to reduce the effects of unwanted pharmaceuticals on human health and the environment.

In schizophrenia, cognition is closely linked to social competence and influences long-term prognosis. Thus, treatment should target cognitive improvement to enhance the patients’ societal adaptation. This study evaluated the effects of computer-assisted cognitive remediation therapy (CR) using RehaCom® on cognition in patients with schizophrenia. Thirty patients were randomized, with 15 assigned to the CR group and treatment usual care (TAU) and 15 to the TAU alone groups. Over 12 weeks, patients received CR twice weekly, including two computer sessions and one verbal session. Outcomes measured were cognition using the Brief Assessment of Cognition in Schizophrenia and Schizophrenia Cognition Rating Scale, intrinsic motivation using the Quality of Life Scale and Intrinsic Motivation Inventory, psychiatric symptoms using the Positive and Negative Syndrome Scale, negative symptoms using Scale for the Assessment of Negative Symptoms, and functional level using modified Global Assessment of Functioning scale for Functioning. The CR + TAU group demonstrated considerable improvements in cognition, intrinsic motivation, negative symptoms, and functional level compared to the TAU-alone group. These findings indicate that the CR using RehaCom® enhances cognition and other outcomes in schizophrenia.

Solid waste management is challenging in many countries, especially developing economies. The impacts of the pandemic continue to be felt and have indicated secondary impacts on waste management. This work draws on data on household solid waste (HSW), healthcare waste (HCW), and recyclables collected in the Rio de Janeiro municipality, analyzed from January 2018 to December 2022. As expected, the collection of HCW in Rio de Janeiro municipality experienced a noticeable increase in 2020 and 2021, with an average of 46.9 tons and 54.3 tons collected, respectively. Notably, 2021 saw a significant 30% increase compared to 2019 (p-value<0.001). No significant difference was observed in recyclables collected from 2018 to 2021. The average recyclable amount was 3,638 and 3,747 tons per month in 2020 and 2021. In contrast, the monthly amount was equal to 4,819.5 tons in 2022, representing an increase higher than 32% compared to previous years (p-value<0.05). Our findings can be used to adapt and improve waste systems to cope with similar emergency scenarios in the future, serving as a template for municipalities with similar challenges.

This paper focuses on the highly radioactive, long-lasting nuclear waste produced by the currently operating fission reactors and on the way to deal with the sensitive issue of spent fuel reprocessing. The review includes a short description of the fission process and a detailed analysis of the more hazardous radioisotopes produced either by secondary reactions occurring in the nuclear installations or by decay of the fission fragments. Also outlined are the strategies presently adopted to minimize the harmfulness of the nuclear waste to be disposed and discussed advanced options and possible solutions proposed for the recycling of the used fuel and for the reusing of some technologicaly relevant radioisotopes.

There are four categories of medical waste that cannot be mixed as this will cause serious problems such as environmental pollution or infection. In the past, the classification of medical waste often involved a lot of human and material resources to process, with workers at risk of exposure to infectious substances. Therefore, an augmented reality (AR) and artificial intelligence (AI) medical waste classification system and method were developed. This innovative medical waste classification system and method combines AR and AI identification technology to reduce the risk of manual judgment errors by clinical staff when handling medical waste.

Starting from an original survey conducted in eight countries in 2021 (Canada, China, Germany, Italy, Russia, Spain, UK, and USA), this research explores the relationship between household food waste and dietary habits in a cross-country comparative perspective. 8,000 questionnaires were recorded from samples representative of adult population of each country through an online survey conducted between the 13th and the 24th of August. The questionnaires were built on the work of Waste Watcher International Observatory on Food and Sustainability, an international observatory of social, behavioral and lifestyles dynamics behind household food waste. Relationship between per capita self-reported amount of food waste (expressed in kilocalories) and self-declared dietary habits (Traditional, Healthy and Sustainable, Vegetarian, Smart, Confused) was estimated using multiple linear regression models. Results show that Smart diets are associated with higher values of food waste in Canada, Spain, UK and USA. Vegetarian diets are associated to lower food waste values in China, Germany, UK and USA but not in Italy, Russia and Spain. Since the share of population adopting a Smart diet is on average 2.7% of the sample, interventions for food waste reduction should focus on this specific type of consumers, often associated to larger amounts of food waste.

The regional recycling of plant waste from municipal green space maintenance, private households and private gardens is traditionally carried out in partially open composting plants. In addition to climate-relevant gases, dust, germs and odours are emitted. Compared to aerobic rotting the pyrolysis at higher temperatures and/or reforming offers industrial utilisation of plant based biowaste, with additional availability of energetic by-products. A high-quality plant charcoal derived from a pilot plant is used in a one-year field trial to establish a theoretical comparability with substrates from composting. The advantages and disadvantages of composting and high-quality pyrolysis is shown for comparison, to foster further investigation in advanced technologies for production of plant charcoal aiming the sequester of biogenic Carbondioxide.

In this study on volume determination in waste sorting facilities, we evaluate the effectiveness of ultrasonic sensors and address waste-material-specific challenges. Although ultrasonic sensors offer a cost-effective automation solution, their accuracy is affected by irregular waste shapes, varied compositions, and environmental factors. Notable inconsistencies in volume measurements between storage bunkers and conveyor belts underscore the need for a comprehensive approach to standardize bale production. With prediction reliability being constrained by limited data sets, undocumented modifications to machine-settings and sensor failures, this task renders a challenging application area for Machine Learning. We explore related research and present dataset analyses from three distinct waste sorting facilities in Europe, addressing issues as sensor usability, data quality and material specifics. Our analysis suggests promising strategies and future directions for enhancing waste volume measurement accuracy, ultimately aiming to advance sustainable waste management.

: One of the challenges facing operations management is the design, choice and imple-mentation of action plans adapted to the magnitude of the deviations of the variables of an industrial process. Making conscious and quick decisions is crucial to achieving im-provements in productivity. This will be achieved if the organization's internal and external communication model is strategically designed, considering specific cultural factors and the symmetry or asymmetry required in the communication model. However, how do we organize ourselves and through what channels do we communicate within a production process to generate Big Data that combines data from technologies and the perception, comprehension and projection of experienced humans? Our purpose is to create an operations management model that facilitates the incorporation of technology, allows a prompt response to failures, and promotes the sustainability of processes, without losing sight of its alignment with the organizational strategy. The developed model was implemented in an operations management team, following the guidelines of an action researcher methodology. This resulted in the design of an operations management model and a detailed methodology for its implementation, achieving sig-nificant improvements in the metrics of the current process, making it a success story.

Waste management is a significant issue that Indonesia must face. The presence of waste will always exist as long as life continues. One of the main challenges in waste management is the proper separation of organic and inorganic waste. As a solution to address this issue, the Ministry of Environment has made efforts to develop Waste Banks. However, it also creates new problems related to manual data collection, lack of monitoring by the community in implementing waste management activities, and a lack of specific reports regarding waste management conducted by officers. We propose the creation of a website using the Agile Development SDLC method. This website involve several steps and incorporate functions for data digitalization and expedited data collection, such as the addition of QR Code functionality, Monthly Reporting Function, and enhanced data security. The method used in this research is Agile Development. The application has been developed with a user-friendly interface and the latest web development technologies to ensure smooth performance. Overall, the web-based application for organic and inorganic waste using Laravel is an important step to promoting sustainable waste management practices.

The Metabolic Food Waste [MFW (kg of food)], first time developed in 2016 as a new indicator by Serafini and Toti, indicates the amount of food consumed over the nutritional requirements and the impact of this overconsumption on the environment. It is necessary to identify the causes and to develop potential methods to prevent and reduce MFW, at the same time with increasing consumer awareness about unsustainable diets and changing diet habits toward more environmentally conscious consumption patterns. By analysing and corroborating external data available for food waste, nutritional requirements, environmental impact of food waste and consumer behaviour, we identified as primary causes for MFW the lack of nutritional education and little understanding of the nutritional requirements amongst all categories of consumers, no access to appropriate food resources or reduced availability of fresh produced food. We conclude that for the quantification of the negative impact of MFW on both the environment and human health, we need a decisive action to raise consumer awareness for healthy and sustainable diets, together with an uniform worldwide distribution of the nutritious food.

In this study, 12 organic waste materials were subjected to TG/DTG thermogravimetric analysis and DSC calorimetric analysis. These analyses provided basic information about thermochemical transformations and degradation rates during organic waste pyrolysis. Waste materials were chosen to cover the most abundant waste that can be found in the municipal solid waste stream. Based on TG results, kinetic parameters according to Coats–Redfern method were determined. The pyrolysis activation energy was the highest for cotton 134.5 kJ∙(mol∙K)-1 and the lowest for leather 25.2 kJ∙(mol∙K)-1. The DSC analysis showed number of transformations occurred during pyrolysis for each material. For each transformation, normalized energy required for transformation, or released during transformation were determined and then summarized to present energy balance. The study found that only for three waste materials: PET (-220.1 J⸱g-1), leather (-66.9 J⸱g-1), and chicken meat (-130.3 J⸱g-1) energy balance was negative, while the highest positive balance value was found for potato peelings (367.8 J⸱g-1). The obtained results may be applied for the modelling of energy and mass balance of municipal solid waste pyrolysis.

The detrimental consequences of soil pollution caused by crude oil or petroleum products are immense, leading to land degradation, property damage, and rendering agricultural practices ineffective. Extensive research has been conducted in the field of soil remediation, but further studies are still required to explore additional details of the remedial process. As a result, this study focuses on evaluating the effectiveness of Vernonia Galamensis and Vernonia Amygdalina, commonly known as bitter leaf, in remediating hydrocarbon-contaminated soil. In the analysis of micro-organisms, it was found that the bitter leaf extracts contained three types of bacteria: Pseudomonas aeruginosa, Staphylococcus aureus, and Escherichia coli. The leaf extracts were prepared using different methods, including sun drying, room drying, and using them in their wet form, which were then blended into the contaminated soil. The study also took into consideration three different types of soil: sandy-loamy soil, clay soil, and swamp soil. These advanced techniques and considerations are relevant to the topic of revolutionizing soil remediation, as they explore the potential of bitter leaf extracts and different soil types in effectively mitigating the effects of hydrocarbon contamination.The findings revealed that the wet blended extracts of Vernonia performed exceptionally well in the remediation process, surpassing a 50% reduction in the initial contamination levels. The study involved utilizing a quantity of bitter leaf ranging from 10g to 40g, which was added to the contaminated soils and monitored for a duration of 40 days. Remarkably, this approach led to a significant decrease in the concentration of contaminants within the soil, indicating the effectiveness of the bitter leaf extracts in the remediation process. Towards the conclusion of the study, predictive models were constructed to forecast the impact of hydrocarbon content, as well as the levels of lead, zinc, and chromium in the soil. These variables served as the dependent variables in the models, while the mass of bitter leaf, the duration of treatment, and the pH of the soil were considered as independent variables. Significantly, the models achieved a level of significance of less than 0.05, indicating their statistical validity. Furthermore, the r2 value, which represents the goodness of fit, demonstrated an appreciable level of accuracy in predicting the remediation effects. These results highlight the potential of the developed models in assessing and predicting the remedial outcomes of hydrocarbon contamination using bitter leaf extract.

Globally, open-pit coal mining is associated with severe land use impact and contamination of soil and water resources with heavy metals. Thus, in growing economies like India, where coal is a significant energy source, the heavy metals contamination of soil and water become ubiquitous. Remediation of such a large stretch of mined-out land is a major challenge and a costly process for the mining industry. In recent years, the application of biochar for the remediation of such heavy metals-contaminated soil has been widely practiced. However, applying biochar and cultivating plants in field conditions becomes challenging. This study uses a unique remediation approach by developing biochar-bentonite-based seed balls encapsulating Shorgham grass seeds at their core for application in the contaminated soil. The seed ball was developed by using the bentonite biochar composite in varying weight fractions of 0.5 – 5 % with respect to the kaolinite, whose fractions in the seed ball also varied at one, three, and five parts. The seed balls were applied to the pots containing 3 kg of heavy metals contaminated soil for a pot-culture study in a polyhouse for a period of four months. Initial soil analysis results indicated that the mine soil samples showed poor nutrient and organic matter content and were contaminated with heavy metals such as Ni, Zn, Cr, and Cd. Post-pot-culture soil analysis results indicated that the application of seed balls containing five fractions of biochar composite with its combination with three and five-weight fractions of kaolinite showed substantial improvement in the pH, available nutrients, organic matter content, soil enzymes, and overall soil fertility index compared to the controlled study and other cases. The same combination of seed balls also significantly reduced the plant-available fractions of Ni, Zn, Cr, and Cd in the soil and the translocation of these heavy metals from the rhizosphere zone to the grass’s aerial parts, indicating stabilization of heavy metals within the soil matrix. Moreover, the application of seed balls also substantially improved the plant physiology and reduced the release of stress hormones such as proline and glutathione within the plant cells indicating improvement in the plant’s biotic and abiotic stress factors. Thus, the application of seed balls in heavy metals contaminated soils, particularly over a large stretch of land, could be a low-cost and viable remediation technique.

Multi-modal Motion-assisted Memory Desensitization and Reprocessing Therapy (3MDR), an interactive, virtual-reality assisted, exposure-based intervention for PTSD, has shown promising results for treatment-resistant Posttraumatic Stress Disorder (TR-PTSD) among military members (MMs) and Veterans in Randomized Controlled Trials. Previous research has suggested that emotional regulation (ER) and emotional dysregulation (ED) may be factors which are correlated with symptom severity and maintenance of TR-PTSD. This embedded mixed-methods pilot study (n=9) sought to explore the impact of 3MDR on ER and ED of MMs and Veterans. Difficulties in Emotional Regulation Scale (DERS-18) data was collected at baseline, prior to each session, and at 1 week, 1 month and 3 months post-intervention and analyzed using a Wilcoxon signed-ranks test. Qualitative data collected from sessions, debriefs, and follow-up interviews were transcribed and descriptively analyzed. Results demonstrated statistically significant decreases in DERS-18 scores from pre-intervention to post-intervention at each timepoint. Qualitatively, participants perceived improvements in ER within specified DERS-18 domains. We describe how 3MDR’s unique and novel approach may address ED through cognitive-motor stimulation, narration, divergent thinking, reappraisal of aversive stimuli, dual-task processing, and reconsolidation of traumatic memories. Further investigation is underway to better understand the underlying neurobiological mechanisms by which 3MDR addresses ER and PTSD.

This work aims to investigate the effect of process temperature and catalyst content by thermochemical degradation of municipal solid waste (MSW) fraction (organic matter + paper + plastic) on the yield of reaction products (bio-oil, biochar, H2O and gas), physicochemical properties and chemical composition of bio-oils, as well as on the morphology and crystalline phases of biochar in laboratory scale. The organic matter, paper and plastic segregated from the gravimetric composition of total waste sample were subjected to the pre-treatments of drying, crushing and sieving. The experiments were carried out at 400, 450 and 475 °C and 1.0 atmosphere, and at 450 °C and 1.0 at-mosphere, using 5.0, 10.0 and 15.0% (wt.) of FCC zeolite, bath mode, using a laborato-ry scale glass reactor. The bio-oil was characterized for acidic value. The chemical functions present in the bio-oil identified by FT-IR and the composition by GC-MS. Biochar was characterized by SEM/EDS and XRD. Thermal pyrolysis of the MSW frac-tion (organic matter + paper + plastic) shows bio-oil yields between 9.44 and 9.24% (wt.), aqueous phase yields between 21.93 and 18.78% (wt.), solid phase yields between 67.97 and 40.34% (wt.) and gas yields between 28.27 and 5.92% (wt.). The yield of bio-oil decreases with increasing process temperature. For the experiments using FCC, the biochar and gas yields increase slightly with the FCC content, while that of bio-oil de-creases and the H2O phase remains constant. The GC-MS of bio-oils identified the presence of hydrocarbons and oxygenates, as well as nitrogen-containing compounds, including amides and amines. The acidity of the bio-oil increased with increasing temperature and with the aid of FCC as a catalyst. It has been identified the presence of hydrocarbons within bio-oil by addition of FCC catalyst due to the deoxygenation of carboxylic acids, followed by decarboxylation and decarbonylation reactions, producing aliphatic and aromatic hy-drocarbons.

The introduction of organic and inorganic substances to the environment is a result of human activities such as agriculture, domestic and industrial wastewater which leads to pollution. Treatment processes of these wastewaters are being conducted globally to eliminate easily settled materials and recover nutrients in an attempt to release clear and apparently clean effluent into natural waters. Lack of removing inorganic nitrogen and phosphorus nutrients is the greatest cause of eutrophication in water bodies which inhibits the life of other organisms as well as pose a threat to human life and loss of the economy. Different technologies have been applied and are being developed to recover nutrients as well as heavy metals from wastewater to meet the permissible limits before discharging effluents. Wastewater treatment using microalgae offers an opportunity to provide tertiary bio-treatment and production of valuable biomass. Microalgae use the available inorganic nitrogen and phosphorus for their growth which are then harvested for various uses. Additionally, they have the ability to remove heavy metals and some toxic compounds. The main specific microalgae species in this study is the Chlorella sorokiniana with the Aequorea victoria jellyfish This paper reviews some of the wastewater treatment processes and focus on the use of microalgae and some of the shortcomings of the technologies and how they can be improved to achieve maximum nutrient recovery economically with low energy demand.

In the face of 21st-century environmental challenges, including climate change, migration pressures, and waste disposal issues, certain healthcare sectors, notably dentistry, pose a significant global environmental footprint with concerns about carbon emissions and waste production. This scoping review delves into the paradox that healthcare, while dedicated to safeguarding health, inadvertently contributes to environmental degradation through waste accumulation and disposal. The analysis of relevant pertinent literature emphasizes the imperative for an environmentally sustainable approach to dental waste measurement, disposal methods, and comprehensive education for stakeholders. Aligned with the World Conference on Sustainable Development and the United Nations' 2030 Agenda, the study adhered to PRISMA-ScR scoping review guidelines and Institute of Medicine's recommendations. The study utilized Medline/PubMed and international organization websites for data retrieval, employing Boolean operator queries in Medline. A systematic literature analysis identified six cross-sectional studies (2004-2018) highlighting variations in dental waste composition due to the lack of standardized identification methods. This heterogeneity underscores the need for a proposed research model, emphasizing comprehensive methodologies and healthcare staff training in waste management. The study advocates for environmentally conscious dental practices, contributing to broader sustainable healthcare goals through sharing of a research protocol for dental solid waste management.

Tomato quality is intricately regulated by a combination of factors, including the presence of bioactive compounds referred to as secondary metabolites and various organoleptic characteristics. These attributes are notably influenced and harmonized by the specific growing conditions, with a particular emphasis on the type of fertilization employed. Traditionally, chemical fertilizers have been favoured in crop cultivation due to their cost-effectiveness and ability to accelerate crop growth. However, in pursuit of sustainable and intelligent agricultural practices, there is a growing need for alternative fertilizers. In this context, the present study aimed to assess the impact of fertilizers derived from waste materials, specifically sulphur bentonite and orange residue (referred to as SB), on tomato quality. This assessment extended to examining qualitative and quantitative alterations in aroma-related volatile compounds and the antioxidant systems of tomatoes, in comparison to the conventional use of fertilizers such as horse manure and NPK (nitrogen, phosphorus, and potassium). The results obtained revealed distinct effects of different fertilizers on tomato quality. Notably, parameters such as TPRO (total protein), TCARB (total carbohydrate), LIC (lycopene content), TCAR (total carotenoid content), total phenols, total flavonoids, and aroma profiling exhibited significantly superior values in the group treated with SB fertilizer. These findings strongly suggest that the novel fertilizer functioned as a bio-stimulant, enhancing the nutraceutical and sensory attributes of tomatoes, with a pronounced impact on the synthesis of secondary metabolites and the aroma profile of the fruits.

Leather waste was carbonized at 800 °C in inert atmosphere. The resulting biochar was coated in situ with polypyrrole nanotubes produced by the oxidation of pyrrole in the presence of methyl orange. The composites of carbonized leather with deposited polypyrrole nanotubes of various composition were compared with similar composites based on globular polypyrrole. Their molecular structure was characterized by infrared and Raman spectra. Both conducting components formed a bicontinuous structure. The resistivity determined by four-point van der Pauw method was monitored as a function of pressure applied up to 10 MPa. The typical conductivity of composites was of the order of tenths to units S cm−1 and it was always higher for polypyrrole nanotubes than for globular polypyrrole. The conductivity decreased by 1–2 orders of magnitude after treatment with ammonia but still maintained a level acceptable for applications operating under non-acidic conditions. The composites were tested for dye adsorption, viz. cationic methylene blue and anionic methyl orange, using UV-spectroscopy. The composites are designed for the future use as functional adsorbents controlled by the electrical potential.

Solid waste has become a tenacious issue worldwide. It has been increasing exponentially due to urbanization and the increase in the population. Since the twentieth-century technological revolution, there have been significant changes in the composition of solid waste. It poses significant challenges for waste management systems worldwide. Waste management is the process of handling waste right from its creation to its final disposal, including transport, collection, treatment, and monitoring. The present solid waste management (SWM) system is affected by unfavorable institutional, economic, technical, legislative, and operational constraints. Poor waste management is affecting ecosystems and human health, damaging our finite natural resources, impeding human economic progress, and harming people's quality of life. Now, researchers are concerned about the environment's degradation, a decline in quality of life, and risks related to waste management grow as the volume of solid waste. So, they are focusing on sustainable waste management practices which will be crucial for creating a cleaner and healthier environment for future generations. This chapter focuses on the concept of solid waste, its types, management, and its effect on the health of humans and the environment.

The circular economy (CE) has emerged as a viable alternative for tackling the problems caused by rising consumption, including solid waste (SW). The present study conducted a meta-analysis of research published between 2012 and 2022 on CE and solid waste management (SWM). A bibliometric analysis was used from the Web of Science (WoS) and Scopus databases. By studying the articles, we briefly discussed the connections between them and how one contributes to the evolution of the other. Some findings point to greater collaboration between Italy and Bolivia, followed by China and Malaysia. However, they move away from the traditional axes as the United States and Canada. In addition, it was found that the adoption of reuse and selective collection, in fact, allow the reduction of the volume of discarded materials. In this way, it was possible to conclude that a greater connection between CE and GRS makes it possible to optimize the useful life of landfills through the treatment of organic waste and recycling, to encourage waste picker cooperatives and selective collection programs, and to reduce the financial costs of the system as a whole, making it more durable and sustainable.

Waste management is an unavoidable technological operation in the process of raw material extraction. The main characteristic of this technological operation is the handling of large quantities of waste material, which can amount to several hundred million cubic metres. Working with this amount of material usually requires high-capacity systems for excavation and loading, a large fleet of trucks for haulage, construction, and maintenance of a complex roads network, use of a significant area of land in order to achieve the required capacities, etc. At the same time, this operation must comply with all administrative and environmental standards. Therefore, optimising waste rock management (particularly haulage and dumping) has the potential to significantly improve the overall value of the project. This paper presents a hybrid model for the optimisation of waste dump design and site selection. The model is based on different mathematical methods (genetic algorithm, analytic hierarchy process and heuristic methods) adapted to different aspects of the problem. The main objective of the model is to provide a solution (in analytical and graphical form) for the draft waste dump design, on the basis of which the final waste dump design can be defined.

Sherubtse College under Royal University of Bhutan has a total of 1582 students, where 787 0f them are female. They suffer from menstrual and menstrual cramps every month and they use napkins to stay clean and healthy. As all the college girls are educated on the norms and use of sanitary napkins, the proper management of the waste generated is lacking. The disposal of used sanitary napkins and management is a challenge to the college management. This small research aims to investigate on how girls in college campus manage the menstural waste and the amount of sanitary napkins used. The lack of proper dumping areas leads to the improper sanitary waste management and sometimes the waste generated from the sanitary napkins are toxic and unhealthy. It is very important to initate some ways to dump the pads and its related problem should be seriously addressed by the college management. It is also important to come up with different soultion and management of these wastes for sustainable environment. Therefore, this research will be mainly mentioning about the suggestions and how the sanitary waste is being managed in Sherubtse College campus and the amount of sanitary pads used in a month or an year.

Thermal and catalytic pyrolysis of virgin low-density polyethylene (LDPE), high-density polyethylene (HDPE), polypropylene (PP) and mixtures of LDPE/PP were carried out in a 200 ml laboratory scale batch reactor at 460 °C in a nitrogen atmosphere. Thermogravimetric analysis (TGA) was carried out to study the thermal and catalytic degradation of the polymers at a heating rate of 10 °C/min. The amount of PP was varied in the LDPE/PP mixture to explore its effect on the reaction. In thermal degradation (TGA) of LDPE/PP blends, a lower decomposition temperature was observed for LDPE/PP mixtures compared to pure LDPE, indicating interaction between the two polymer types. In the presence of a catalyst (CAT-2), the degradation temperatures for the pure polymers were reduced. The TGA results were validated in a batch reactor using PP and LDPE respectively. Thermal cracking results showed that the oil product contains a significant amount of gasoline (C7 − C12) and diesel (C13 − C20) hydrocarbon fractions. The catalyst enhanced cracking at lower temperatures and narrowed the hydrocarbon distribution in the oil towards the gasoline range fraction (C7 – C12). The result suggests that the oil produced from catalytic pyrolysis of waste plastics has a potential as an alternative fuel.

Enzymes are biological molecules produced by living entities for carrying out biological processes. The application of enzymes for waste treatment has been gaining pace commercially to solve concerns related to agricultural residues, wastewater, replacement of synthetic processes with natural ones, etc. The application of enzymes for waste management has been an environmentally reliable and sustainable process. Treatment of waste with enzymes such as xylanase, proteases, hydrolases, cellulose, peroxidases, chitinases, laccases, etc. has been studied to be effective. These enzymes act upon the waste products and transform them into biodegradable forms that can be recycled, reused and converted to value-added products. They have wide applications and utility as it has been an effective approach, economically cheaper and sustainable techniques. Application of such enzymes for waste management would be beneficial for reducing the quantity of waste, diminishing the negative effects of waste and pollution on the environment, and would be beneficial in bio-converting the waste products into alternate sources of energy. The current chapter focuses on different types of enzymes, their applications for waste management, and their limitations. This chapter also emphasizes the usage of some prominent microorganisms, their secreted enzymes and their proposed mechanisms of action involved with the degradation of the waste products.

The white wine industry generates a large amount of wastes and composting is an alternative for recycling these residues with agronomic and environmental advantages. With this aim, grape marc and grape stalks were composted in static and turned piles, with 3 and 6 turns, to investigate the effects of pile conditions during composting in order to improve final compost quality. Thermophilic temperatures were attained soon after pile construction, and the highest maximum temperatures were achieved in the turned piles (70.5-71.8 ºC). However, pile moisture content decreased bellow recommended values after day 42 in these piles. The extremely high temperatures and low moisture content in turned piles hampered OM mineralization rates and the amount of potentially mineralizable organic matter (OM0) (391-407 g kg-1), whereas the structure of the static pile provided adequate porosity to increase OM decomposition and OM0 (568 g kg-1). This study shows that composting grape marc with stalks, for a period of 140 days, resulted in stabilized and matured compost (NH4+-N / NO3--N &lt;0.5), with good chemical characteristics for application as soil organic amendment in vineyards, without the need for rewetting or turning the piles, thus reducing the agronomic, and environmental cost of the composting process.

The article discusses an alternative way of recycling radioactive waste (RW), presented in the form of radioactive building materials - concrete and reinforced concrete structures and metal fittings, with the further use of materials, obtained during recycling, in the space industry. That is, it is supposed to send radioactive waste into space not as a passive ballast, but as a payload that will operate in space under conditions of increased radiation.

Significant problems have arisen in the last years, such as climate change, global warming, and hunger. These complications are correlated with the depletion and exploitation of natural resources and environmental contamination. Due to overcrowding, the list of challenges for the next few years is growing. A comprehensive approach was made to the agro-industrial production of Avocado (Persea americana) and the management of all its biomass waste. So, bioprocesses and biorefinery can be used to produce high added-value products. A large number of residues are composed of lignin and cellulose. They have many potentials to be exploited sustainably for chemical and biological conversion; physical, chemical, and natural treatments improve the following operations. There are some applications to many fields such as pharmaceutical, medical, material engineering, and environmental remediation. Possible pathways are mentioned to take advantage of Avocado as biofuels, drugs, bioplastics, and even in the environmental part and emerging technologies such as nanotechnology using bioprocesses and biotech. In conclusion, Avocado and its waste could be transformed into high value-added products in industries above to mitigate global warming and save non-renewable energy.

Named herein “CytroCell”, the cellulosic material obtained via hydrodynamic cavitation of citrus processing waste in water is cellulose of low crystallinity, high porosity, good water holding capacity and good dispersibility in water. These properties, here demonstrated for the first time for lemon and grapefruit CytroCell, open the route to mass scale production of a useful functional material from a cheap and abundant biowaste. The process, indeed, does not require any pre-treatment of the raw material, and does not use acid, alkali, chemical oxidants or enzymes.

The potential of Sorghum bicolor L. (Moench) (Epuripur 1995) to phytoremediate petroleum oil-adulterated soils from an automobile repair workshop and the effect of enhancement factors: NPK fertilizer, cow dung and sewage sludge in in situ phytoremediation of the soil by the plant were assessed in this study. 50kg of petroleum oil-contaminated soil was collected from the workshop and divided into five equal portions. Four portions were potted with four sorghum plants with three subjected to equal amounts of enhancements (5%w/w) under normal growth conditions for 72 days. Representative soil samples were collected from spots at depths of 0–10 cm and 10–20 cm from the potted soils and subjected to Soxhlet oil extraction after 72 days. Experimental results revealed that S. bicolor survived in the petroleum oil-contaminated soils. Amendment of the petroleum oil-vitiated soils with cow dung, sewage sludge and NPK fertilizer augmented the remediation capacity of Epuripur 1995 by 12.5%, 6.3% and 9.1%. Addition of cow dung to crude oil contaminated soils could make such soils fully reestablished for agricultural activities. Further research aimed at determination of the phytoremediation potential of cereals such as corn, barley, rye, millet should be done.

Meat loss and waste are estimated at each stage along the food chain, but the methods used are complex and the data needed often fragmented. We, therefore, evaluated the feasibility of estimating meat loss and waste using a simpler method comparing meat availability and consumption, using Swiss meat consumption according to a national nutrition survey and Swiss meat availability according to food balance sheets. As availability is reported at the fresh meat level and consumption as consumed, items of the latter were converted to fresh meat equivalents before comparing consumption with availability. Consumed unprocessed meat was directly converted to fresh meat equivalents and consumed meat products after having identified their meat ingredients. Meat availability, meat consumption as consumed and as fresh meat equivalent were 138.4 g/d, 105.5 g/d, and 112.1 g/d, respectively. The resulting total meat loss and waste was 19% and varied from −36% to 38% for the different meat types. Estimating meat loss and waste based on meat availability and consumption derived from a national nutrition survey yielded results varying to such an extent that the evaluated method to estimate meat loss and waste cannot be recommended.

Pyrolysis has been applied in the human economy for many years, and it has become a significant alternative to the production of chemical compounds, including biofuels. The article focuses mostly on recent achievements in the technical and processing aspects of pyrolysis. This review provides an overview of the recent advanced pyrolysis technology used in gas, bio-oil, and biochar production. The key parameters to maximize the production of specific chemical compounds were discussed and considered during the construction of the reactors. The emphasis is put on optimizing the process parameters, technical requirements, and renewable energy use in the process and conception to improve the efficiency of product production. The application of pyrolysis gas, oil, and biochar as valuable chemical compounds are related to the intensifying effects of climate change, biofuel production, and waste management in accordance with the principles of sustainable development.

Using machine learning or deep learning to solve the problem of garbage recognition and classification is an important application in computer vision, but due to the incomplete establishment of garbage datasets and the poor performance of complex network models on smart terminal devices, the existing garbage classification models The effect is not good.This paper presents a waste classification and identification method base on transfer learning and lightweight neural network. By migrating the lightweight neural network MobileNetV2 and rebuild it, The reconstructed network is used for feature extraction, and the extracted features are introduced into the SVM to realize the identification of 6 types of garbage. The model was trained and verified by using 2527 pieces of garbage labeled data in the TrashNet dataset, which ultimately resulted in a classification accuracy of 98.4% of the method, which proves that the method can effectively improve the classification accuracy and time and overcome the problem of weak data and less labeling. The over-fitting phenomenon encountered by small data sets in deep learning makes the model robust.