This study surveyed the variation in Perfluorinated Compounds (PFCs) concentration entering urban wastewater treatment plants and proposed an optimal PFCS treatment method. The PFCS concentration in influent was shown to be affected by the types of industries and operating rate. The concentration of PFCs in the wastewater treatment effluent was slightly lower than that of influent. Thus, PFCs were considered to have barely been removed by the existing biological treatments. The pilot test result showed that about 10% of PFCs were removed by coagulation and precipitation, and the ozone and chlorine test also showed that few PFCs were removed regardless of the amount of injection. The activated carbon adsorption test showed that the removal was significantly increased by the empty bed contact time, with about a 60% removal in five minutes and over a 90% removal in 15 minutes. Therefore it is determined that a more stable and higher PFCs removal would result from the continuous oxidation processes such as ozone and adsorption processes such as activated carbon rather than a single biological treatment.

The vegetation in constructed wetlands (CWs) plays an important role in wastewater treatment. Popularly, the common emergent plants in CWs have been vegetation of natural wetlands. However, there are ornamental flowering plants that have some physiological characteristics similar to the plants of natural wetlands that can stimulate the removal of pollutants in wastewater treatments; such importance in CWs is described here. A literature survey of 87 CWs from 21 countries showed that the four most commonly used flowering ornamental vegetation genera were Canna, Iris, Heliconia and Zantedeschia. In terms of geographical location, Canna spp. is commonly found in Asia, Zantedeschia spp. is frequent in Mexico (a country in North America), Iris is most commonly used in Asia, Europe and North America, and species of the Heliconia genus are commonly used in Asia and parts of the Americas (Mexico, Central and South America). This review also compares the use of ornamental plants versus natural wetland plants and systems without plants for removing pollutants (COD, BOD, nitrogen and phosphorous compounds). The removal efficiency was similar between flowering ornamental and natural wetland plants. However, pollutant removal was better when using ornamental plants than in unplanted CWs. The use of ornamental flowering plants in CWs is an excellent option, and efforts should be made to increase the adoption of these system types and use them in domiciliary, rural and urban areas.

Contamination by microplastics (MP) in aquatic ecosystems is largely due to the release of millions of these particles from treated effluents from Wastewater Treatment Plants (WWTP). Due to the lack of policies and regulations that establish criteria for the control and elimination of MP from WWTP effluents, this research evaluated the presence of MP for particle sizes of 38 and 150 µm in influents and effluents from three WWTP in the port of Acapulco, Mexico. Using optical microscopy and Fourier transform infrared spectroscopy (FTIR) techniques, the MP detected were polyethylene (PE), polypropylene (PP), polyethylene terephthalate (PET) and polyvinyl chloride (PVC). MP removal efficiencies of 82.5 to 98.7% (38 µm) and 86.8 to 97.5% (150µm) were obtained; the MP average daily emissions to the receiving bodies of these three WWTPs were in the ranges of 9.5 x 106 - 4.70 x 108 particles and the annual emissions in the range of 3.05 x 109 - 1.72 x 1011 particles. This work reveals the urgency of implementing regulatory policies to avoid the continuous emission of MP to aquatic ecosystems from WWTPs in Acapulco, Mexico.

Preventing the rebound of black and odorous water bodies is critical for improving the ecological environment of water bodies. This study investigated the effect and mechanism of in-situ improvement of sediment microenvironment by nitrate in tailwater of wastewater treatment plants combined with aerobic denitrifying bacteria under low-DO regulation (TailN+CFM+LDO). On the 60th day of remediation, the dissolved oxygen and oxidation-reduction potential in the overlying water increased to 5.6 mg/L and 300 mV, respectively, the acid volatile sulfide in the sediment decreased by 70.4%, and the organic matter in the sediment was reduced by 62.7%, in which the HFOM was degraded from 105 g/kg to 56 g/kg, and the potential risk of water reverting to black and odorous conditions significantly decreased. Amplicon sequencing analysis revealed that the relative abundance of electroactive bacteria Thiobacillus and Pseudomonas with denitrification capacity was found to be significantly higher in the TailN+CFM+LDO group than in the other remediation groups. Functional prediction of 16S sequencing results indicated that both the quantity and activity of critical microbial enzymes involved in nitrification and denitrification processes could enhance in the TailN+CFM+LDO group. These results improved our understanding of the improvement of the sediment microenvironment and could thus facilitate its application.

Preventing the occurrence of secondary caries serves as one of the significant issues in dental clinic, thus make it indispensable to improving the properties of conventional composite resin (CR) by developing a novel CR. In present study, two groups of experimental CRs loaded with different contents of fluoride-doped nano-zirconia fillers (25 wt% and 50 wt%) were fabricated. The surface topography, mechanical performance, fluoride release, antibacterial effect, aging property and cytotoxicity of the experimental CRs were evaluated subsequently. A uniform distribution of the F-zirconia fillers over the whole surface of resin matrix could be observed. The experimental CRs showed continuous fluoride release within 28 days, which was positively correlated with the content of F-zirconia fillers. Moreover, the amount of fluoride release increased in the acidic buffer. Addition of F-zirconia fillers could improve the color stability, wear resistance and microhardness of the experimental CRs, without reducing the flexure strength. Furtherly, the fluoride ions released continuously from the experimental CRs resulted in effective contact and antibacterial properties, while they showed no cytotoxicity. As a consequence, considerations can be made to employ this new kind of composite resin loaded with fluoride-doped nano-zirconia fillers to meet clinical requirements when the antimicrobial benefits are desired.

In Germany, the phloem sucking planthopper Pentastiridius leporinus (Hemiptera: Cixiidae) currently represents the epidemiological driver for the spread of the syndrome “Basses Richesses” in sugar beet, which results in a reduced sugar content and an economic loss for the farmers. This disease is associated with the γ-proteobacterium ‘Candidatus Arsenophonus phytopathogenicus’ and the Stolbur phytoplasma ‘Candidatus Phytoplasma solani’. Recently, P. leporinus was found in potato fields in Germany associated with Stolbur-like symptoms in this crop. In this study, we confirmed that the vector completes its lifecycle on sugar beet as well as on potato when reared under controlled conditions. Transmission experiments with adults of this vector combined with molecular analyses showed for the first time that both pathogens are transmitted by this vector to potato. For an accurate assessment of the Ca. P. solani and Ca. A. phytopathogenicus titers in the vector and host plants, gBlocks derived from the hsp20- and 16S rRNA gene were employed, respectively. For Ca. P. solani the limit of detection was determined in potato and sugar beet material. The results of this study will further research on the epidemiology of the syndrome “Basses Richesses” and “Stolbur” diseases and the response of host plants and vector insects to both pathogens.

Vernonia mespilifolia is widely used in folk medicine in the Eastern Cape Province, South Africa. The aim of this study was to evaluate the biological activity of the acetone, aqueous and ethanol extracts of Vernonia mespilifolia using brine shrimp hatchability and lethality assay. The result showed hatching success in this order: aqueous extract (48.6%) > acetone extract (38.2%) > ethanol extract (26.8%). The LC₅₀ of the lethality assay were in this order: acetone extract (67.8 µg/mL) > aqueous extract (132 µg/mL) > ethanol extract (383 µg/mL). According to Meyer’s toxicity index (using brine shrimps), LC₅₀ < 1000 µg/ mL is toxic. Therefore, the results of the three solvent extracts could be said to be toxic as do have LC₅₀ < 1000 µg/ mL. However, the toxicity of the crude extracts could suggest or confer some antitumor properties, hence further in vitro, in vivo and antitumour assays are recommended to further substantiate these claims.

Cinnamomum tamala leaf (CTL), also known as tejpat and Indian bay leaf, is used all over the world for seasoning, flavouring, and medicinal purposes. Numerous researchers are interested in exploring the nutritional and medicinal benefits of CTL due to their potential as nutraceuticals. These characteristics could be explained by the presence of several essential bioactive substances and lipid derivatives. There are no reports available on this species about its metabolites profile. In this work, rapid screen and identify chemical compounds in supercritical (SC)-CO2 extracts of CTL by use of UPLC-Q-TOF-MSE with multivariate statistical analysis approach was established in both negative and positive mode. As a results, a total of 166 compounds, including 66 monocarboxylic fatty acids, 52 dicarboxylic fatty acids, 27 fatty acid amides, and 21 others were tentatively identified based on accurate mass, and the mass spectrometric fragmentation pattern, out of which 142 compounds are common and found in all five CTL extracts. They displayed robust [M+H]+ and/or [M-H]- ions in both low- and high-energy collision-induced dissociations (CIDs). Based on chemical profiling and chemometric analysis, CTL4 (300bar/55°C) extract was found significantly more potent in other CTL’s extracts. A new mono- and di-carboxylic fatty acids, fatty acid amides and other essential bioactive compounds were separated within 20 min runtime and identified in CTL for the first time. The combination of UPLC-Q-TOF-MSE and chemometric analysis is a powerful method to rapidly screen the metabolites profile for the quality control of C. tamala leaf.

Electrochemical methods are used for the treatment of both municipal and industrial wastewater, either independently or in conjunction with biological methods. This conjunction is used for pretreatment or posttreatment of biologically treated wastewater. In our work, we focused on the combination of these processes, where pre-electrolysis was used to produce dissolved iron before the activation process. Electrolysis was also directly introduced into the activation using either iron or carbon electrodes. The surface of one iron electrode was 32.2 cm2, the applied voltage was 21 V, and the supplied current was 270 mA. The surface of one carbon electrode was 7.54 cm2, the supplied current was 82.5 mA, and the applied voltage was 21 V. From laboratory research on the treatment of synthetic municipal wastewater using a combination of electrolysis and activation processes, it resulted that the use of iron electrodes increased the efficiency of phosphorus removal compared to its precipitation with iron salts. The electrolysis had a positive effect on the sedimentation properties of sludge and the destruction of filamentous microorganisms. Electrolysis negatively affected the respiration rates of activated sludge and the efficiency of denitrification. However, it did not have a negative impact on the nitrification activity of the sludge.

The per capita availability of freshwater resources on a global scale is gradually decreasing due to population growth, rapid urbanization, industrialization, and modern lifestyles. In this situation, wastewater management becomes a major concern. Conventional treatment processes used to treat wastewater discharges are not adequate for the advanced removal of pollutants, especially refractory organic pollutants, which are mainly organic compounds that are not easily biodegradable in the environment. The use of photocatalytic membrane reactors (PMRs) for tertiary wastewater treatment has attracted much interest in recent periods, and various configurations have been investigated. The performance of a PMR using an iron doped titanium photo catalyst and Polysulfone-based polymeric membrane for municipal wastewater treatment was evaluated under natural and simulated solar light. Obtained results proved that solar driven PMRs can remove organic loading (COD) with high efficiencies and may represent a suitable alternative for the tertiary treatment step of municipal wastewater.

The assessment of an organization/product's environmental footprint is based on the protocols developed by the Joint Research Centre of the European Union, which take into account 16 impact categories. Among the categories covered are toxicity to freshwater ecosystems and to humans. Standard protocols use only chemical parameters as input data, preventing the true impact of entire complex mixtures, such as emissions discharged into the environment, from being determined. Biological assays allow us to bridge this gap: in the current study, assays were used to determine baseline toxicity towards aquatic organisms (green algae, luminescent bacteria, and crustaceans) as well as specific toxicity (mutagenicity and carcinogenicity). Expected impacts were compared using two approaches (standard and bioassay-centered results obtained are not always in line and, in general, the traditional method underestimates impacts). This demonstrates the importance of these assays and suggests that they be used in LCA (Life Cycle Assessment) protocols as well.

High-strength wastewaters from a variety of sources, including the food industry, domestic septage and landfill leachate, are often hauled to municipal wastewater treatment plants (WWTPs) for co-treatment. Due to their high organic loadings, these wastewaters can cause process upsets in both the WWTP’s liquid and solids treatment trains and consume organic treatment capacity, leaving less capacity available to service customers in the catchment area. A novel pre-treatment method, the Waste Activated Sludge-High Rate (WASHR) process, is proposed to optimize the co-treatment of high-strength wastewaters. The WASHR process combines the contact stabilization and sequencing batch reactor processes. It utilizes waste activated sludge from the municipal WWTP as its biomass source, allowing rapid start-up. Bench scale treatment trials of winery wastewater confirm the WASHR process can reduce loadings on the downstream WWTP’s liquid treatment and solids treatment trains. A case study approach is used to confirm the economic viability and environmental sustainability of the WASHR process compared to direct co-treatment using life cycle cost analyses and greenhouse gas emissions estimates.

Piggery wastewater (PWW) is characterized by its high concentrations of organic matter and ammonium, and by their odour nuisance. Traditionally, PWW has been treated in open anaerobic lagoons, anaerobic digesters and activated sludge systems, which exhibit high greenhouse gas emissions, a limited nutrients removal and a high energy consumption, respectively. Photosyn-thetic microorganisms can support a sustainable PWW treatment in engineered photobioreactors at low operating costs and with an efficient recovery of carbon, nitrogen and phosphorous. These microorganisms are capable of absorbing solar irradiation through the photosynthesis process to obtain energy, which is used for their growth and associated carbon and nutrients assimilation. Purple phototrophic bacteria (PPB) represent the photosynthetic microorganisms with the most versatile metabolism in nature, while microalgae are the most studied photosynthetic microor-ganisms in recent years. This review describes the fundamentals, symmetry and asymmetry of PWW treatment using photosynthetic microorganisms such as PPB and microalgae. The main photobioreactor configurations along with the potential of PPB and microalgae biomass valori-zation strategies are also discussed.

Microalgae wastewater treatment has long been promoted as a sustainable method to handle the influx of human waste due to population growth. Initially, in the early 1900’s, microalgae was noted to increase wastewater treatment efficiency by aerating the water and consuming waste. By mid-century, wastewater grown microalgae was being investigated as a way to produce biomass for food, fuel, and other biomaterials. The space race in the 1960’s led to the use of microalgae in life support systems. Technological developments and political pressure in the 1970’s spurred studies of the impact of wastewater on the growth of phytoplankton in the oceans as well as methods to use microalgae wastewater treatment in aquaculture. Simultaneously, the oil crisis of that decade promoted research of alternative fuels, which included microalgae biofuels via the Aquatic Species Program. This program led to research into the use of wastewater as a feedstock for microalgae growth. By the later 2000’s, instability in the oil market caused another energy crisis which further prompted investment in microalgae biofuels, some of which involved combined wastewater treatment. Currently, microalgae wastewater treatment is being researched as a way to cut back on greenhouse gas emissions to curb global warming and produce sustainable biofuels.

Wet coffee processing methods will produce wastewater containing organic matter. The high content of organic matter can be utilized as biogas through the anaerobic process. Anaerobic digesters construction can affect removal process of wastewater pollution and biogas quantity. The purpose of this study is to determine the effect of digester construction between conventional digester, CSTR and UASB producing biogas from coffee wastewater. The conventional digester worked without temperature control system as control, a UASB digester, and CSTR digester worked with temperature control system. Biomass volume was about 5 L with 35 days incubation time. Temperature and pH for UASB and CSTR were set within the range 30 – 35^oC and pH 6.0 – 8.0. Based on the feeding variations, UASB has a stable performance with 83.57 ml/day of average biogas production. It has also highest remediation efficiency of COD, BOD and C/N with 85.00±0.34 %, 84.40%± 5.66 and 97.78± 0.57.

In recent years, there is a growing concern about the alarming spread of antimicrobial resistance (AMR) in different environments. Increasingly, many species of bacteria, fungi and viruses are becoming immune to the most commonly used pharmaceuticals. One of the causes of the development of the resistance is the persistence of these drugs, excreted by humans, in municipal and hospital wastewater (WW). Consequently, wastewater treatment plants (WWTPs) are a primary source of antimicrobial resistance genes as novel pollutants. This systematic review sought to examine the relevant literature on pharmaceutical residues (PRs) responsible for AMR in municipal and hospital WW in order to propose a classification of the PRs of greatest concern and provide an updated source for AMR management in WWTPs. Among 546 studies collected from four databases, 18 were included in the present review. The internal and external validity of each study was assessed, and the risk of bias was evaluated on a 20-parameter basis. Results were combined in a narrative synthesis discussing influents and effluents PR concentrations at 88 WWTPs, seasonal variations, differences between hospital and municipal WW, environmental risk assessment values of antimicrobial substances and treatment facilities removal efficiencies. Among the 45 PRs responsible for AMR evaluated in this study, the antibiotics ciprofloxacin, clarithromycin, erythromycin, metronidazole, ofloxacin, sulfamethoxazole and trimethoprim constitute a considerable risk in terms of ubiquitous distribution, worrying concentrations, risk quotients values, and resistance to removal treatments. Gaps in knowledge, data and information reported in this review provide a valuable source for managing AMR in WWTPs.

The present study aimed at investigating the in vitro and in vivo susceptibility of malaria parasites to crude extracts and fractions from Polyalthia suaveolens, Uvaria angolensis, and Monodora tenuifolia. The ethanolic extracts were prepared by maceration, and were further partitioned using water, dichloromethane, hexane, and methanol. The most promising fraction was subjected to column chromatography and the sub-fractions tested for activity in vitro. The antiplasmodial effect of extracts and fractions was tested against the Chloroquine resistant (PfK1) strain in 96 wells microtiter plate format using SYBR green florescence assay. The promising fraction was further assessed for cytotoxicity and acute toxicity in Swiss albino mice and subsequently against the rodent malaria parasite, P. berghei. Qualitative phytochemical screening was also performed on the promising fraction. The methanol fractions exerted the overall better effect with that of the twigs of P. suaveolens (PStw(Ace)) showing the highest potency with a IC50 value of 3.24 µg/mL followed by the fractions of leaf of M. tenuifolia (MoTel(Ace), IC50= 3.84 µg/ml) and stem bark of P. suaveolens (IC50= 4.90 µg/ml). The phytochemical screening showed the presence of alkaloids, lactones, and phenols in the more active fraction of P. suaveolens (PStw(Ace)). The chromatographic fractionation of this fraction led to 12 sub-fractions with PS8 sub-fraction being the most active (IC50= 4.42 µg/mL). In vivo, oral administration of 2000 mg/kg b.w of fraction PStw(Ace) in mice showed no signs of toxicity. Also, fraction PStw(Ace) at 400 mg/kg b.w exerted the highest suppressive effect against P. berghei strain B throughout the 4 days experiment (% parasitaemia below 5.2%). Overall, the results achieved supported the use of the three plants in the traditional treatment of malaria in Cameroon. More interestingly, the methanolic fraction of the twigs extract from P. suaveolens might be of interest in future development of an antimalarial phytodrug.

With the ongoing amendment of the EU legislation on the treatment of urban wastewater, stricter requirements for the removal of pollutants are expected, which calls for the need for innovative wastewater treatment technologies. Biological systems are still the first choice. The survey of typical bioreactors applied in wastewater treatment is presented. Wastewater treatment objective, bio-chemical environment and microbial growth are selected as a main criterion for classification of these bioreactors. Hydraulic and kinetic aspects are considered, advantages and drawbacks of these bioreactors regarding the selection of appropriate type of the reactor as well as regarding operation of reactors are mentioned. The aim of this paper is to provide operators and designers with a brief overview of selected traditional and advanced processes, reactors, and technologies for nutrient removal from municipal wastewater. Another goal is to discuss the possibilities and limitations to comply with more strict effluent standards. From the evaluation of the published papers, it follows that the currently applied traditional methods of nutrients removal have the potential to convey also with the expected stricter limits.

Water pollution, intensified by the release of hard-to-degrade pollutants, poses severe threats to ecosystems, human health, and economic development. The existing advanced oxidation processes often involve high operational costs and may result in secondary pollution, highlighting the necessity for innovative and more sustainable solutions. To address these challenges, our study introduces a cost-effective and eco-friendly corona discharge barrier plasma discharger for wastewater treatment. Through the central composite design/response surface methodology, a high decolorization rate of 98% of methylene blue (MB) within 10 minutes was achieved by optimizing parameters such as pH and voltage. Furthermore, the mechanisms of the generation of reactive oxygen species via this device was discussed in detail and the degradation pathways of MB were described. Moreover, this device is also very energy-efficient, with a low energy density and electrical energy per order of 0.15 watt/mL and 5.79 kWh/m³/order, respectively. In conclusion, the plasma discharger developed in this study provides a cost-effective and environmentally sustainable solution for dye wastewater treatment. This research contributes significantly to the advancement of sustainable dye wastewater management practices, offering an innovative method that meets both environmental and economic objectives.

A method based on ultra performance liquid chromatography with diode array detector (UPLC-DAD) was developed for quantitative analysis of five active compounds and chemical fingerprint analysis of Rosa rugosa. Ten batches of Rosa rugosa collected from different plantations in the Xinjiang region of China were used to establish the fingerprint. The feasibility and advantages of the used UPLC fingerprint were verified for its similarity evaluation by systematically comparing chromatograms with professional analytical software recommended by State Food and Drug Administration (SFDA) of China. In quantitative analysis, the five compounds showed good regression (R²=0.999 5) within the test ranges and the recovery of the method was in the range of 94.2–103.8%. The similarities of the fingerprints of 10 batches of the samples were more than 0.981. The developed UPLC fingerprint method is simple, reliable and validated for the quality control and identification of Rosa rugosa. Additionally, simultaneous quantification of five major bioactive ingredients in the Rosa rugosa samples was conducted to interpret the consistency of the quality test. The results indicated that the UPLC fingerprint as a characteristic distinguishing method combining similarity evaluation and quantification analysis, can be successfully used to assess the quality and to identify the authenticity of Rosa rugosa.

Today major environmental issue facing the universe is Industrial wastewater. They are present in the form of various pollutants like organic/inorganic, heavy metals, and non-disintegrating materials at an enormous amount. As of now, eliminating these pollutants from wastewater from industries in a viable manner has become a significant issue. Productive refinement methodologies are required to eliminate those toxins before removal. Furthermore, nanomaterials are innovationally powerful to purification of water by utilizing inexpensive nanofiltration and nano adsorbent. Heavy metal ions removal in an efficient way from the environment is the first and foremost problem from a biological and ecological perspective, and numerous research practices have been dedicated to the removal of harmful metal particles, involved both in the underground and surface wastewater. This article mainly focuses on the nanomaterials utilization of various contaminating materials removal from industrial wastewater with an exceptional spotlight on rare earth components and nanofiber and nanocomposite films. The objective is to offer references an outline in the field of developing nanomaterials utilization for harmful pollutants removal from industrial wastewater for industrializers and analysts.

Zanthoxylum armatum is an forest tree with apomixis characteristic, and RWP-RKs are plant-specific transcription factors known to regulate nitrogen response and embryonic development. However, the genome-wide analysis of RWP-RK family genes in Z.armatum is unclear. In this study, 36 ZaRWP-RK transcription factors were identified in the genome of Z.armatum, among which 15 genes were belonged to the RKD subfamily and 21 belonged to the NLP subfamily. Duplication events of ZaRWP-RK genes were mainly segmental duplication, and synteny analysis revealed close phylogenetic relationship between Z.armatum and Arabidopsis. The analysis of cis-elements indicated that ZaRWP-RK genes may be involved in the regulation of embryonic development of Z.armatum by responding to plant hormones such as abscisic acid, auxin, and gibberellin. Real-time PCR showed that the expression levels of most ZaRWP-RK genes were significantly increased from flowers to young fruits. Protein-protein interaction network analysis further revealed the potential roles of the ZaRWP-RK proteins in apomixis. Collectively, this study provide a theoretical basis for future investigations into the ZaRWP-RK genes and their regulatory mechanisms in the apomixis process of Z.armatum.

In recent years, the discharge of various emerging pollutants, chemicals and dyes in water and wastewater has represented one of the prominent human problems. Since water pollution is directly related to human health, highly resistant and emerging compounds in aquatic environments will pose many potential risks to the health of all living. Therefore, water pollution is a very acute problem that has constantly increased in recent years with the expansion of various industries. Consequently, choosing efficient and innovative wastewater treatment methods to remove contaminants is crucial. Among advanced oxidation processes, electrochemical oxidation (EO) is the most common and effective method for removing persistent pollutants from municipal and industrial wastewater. However, there are still many gaps despite the great progress in using EO to treat real wastewater. This is due to the lack of comprehensive information on the operating parameters which affect the process and its operating costs. In this paper, among various scientific articles, the impact of operational parameters on the EO performances, a comparison between different electrochemical reactor configurations, and a report on general mechanisms of electrochemical oxidation of organic pollutants have been reported. Moreover, an evaluation of cost analysis and energy consumption requirements have also been discussed. Finally, the combination process between EO and another important advanced oxidation technology, PEC, called photoelectrocatalysis (PEC), has shortly been discussed and reviewed. This article showed that there is a direct relationship between important operating parameters with the amount of costs and the final removal efficiency of emerging pollutants. Optimal operating conditions can be achieved by paying special attention to reactor design, which can lead to higher efficiency and more efficient treatment. The rapid development of EO for removing emerging pollutants from impacted water and its combination with other green methods can result in more efficient approaches to face the pressing water pollution challenge.

The treatment of petroleum refinery wastewater (PRWW) is of great interest in the field of industrial wastewater management. The wastewater contains a diverse concentration of contaminants such as oil and grease, petroleum hydrocarbons, phenol, ammonia, sulfides, as well as other organic and inorganic composites etc. The treatment of refinery wastewater has been treated through various processes including; physical, biological, chemical or hybrid methods which combine two or more techniques. Hence, the objective of this review is to summarize the recent research studies applied in the treatment of petroleum refinery wastewater using conventional, advanced as well as integrated treatment techniques. Furthermore, critically highlight the efficiencies and major limitations of each technique as well as prospects for improvement. Several conventional treatment techniques (basically, the physicochemical and biological processes) were discussed. In this context, advanced oxidation processes (AoPs) especially electrochemical oxidation and photocatalysis as well as the integrated/hybrid processes are found effective to remove the recalcitrant fraction of organic pollutants because of their various inherent mechanisms. These techniques could effectively remove COD and phenols concentration with an average removal efficiency exceeding 90%. Hence, the review also presented an elaborate discussion of the photocatalytic process as one of the advanced techniques and highlighted some basic concepts to optimize the degradation efficiency of a photocatalyst. Finally, a brief recommendation for research prospects is also presented.

Solid particle cationic polyacrylamide (CPAM) is one of the most commonly used organic polymer flocculants in oilfield wastewater treatment, but there are some problems, such as slow dissolution rate, and easy to form a "fish-eye" in the process of diluting into aqueous solution. However, the current liquid CPAM products also have some problems, such as low effective content, poor storage stability, degradation in a short time and high preparation cost. In this paper, a secondary processing technology of solid particle CPAM was studied, and a CPAM suspension was successfully prepared. This suspension has an effective content of 50.00%, No separation in 7 days of storage at room temperature, no separation in 30 min of centrifugation at a speed of 2000 r/min, and diluted to a 0.40 % weak gel solution in just 16.00 min. For 1000 NTU of diatomite simulated wastewater, the optimal turbidity removal rate of the suspension was 99.50%, which was higher than the optimal turbidity removal rate of 98.40% for the inorganic flocculant polymeric aluminum chloride (PAC). For oil and gas field oily wastewater, the optimal turbidity removal rate of CPAM suspension was 35.60%, which was higher than the optimal turbidity removal rate of 28.40% for solid particle CPAM.

This study aims to determine the optimal configuration (position and operation duration) for wall mounted mechanical mixers based on the comparison of three-dimensional computational fluid dynamics (CFD) modelling results and physical data collected from the treatment plant. A three-dimensional model of anoxic zone 1, 2 and 3 of Northern Wastewater Treatment Plant (WWTP) located at Cairns Regional Council, Cairns, Queensland, Australia was developed and validated. The model was used to simulate the flow pattern of the WWTP and the simulation results are in good agreement with the physical data varying between 0% to 15% in key locations. The anoxic zones were subject to velocities less than the desired 0.3 metres per second however results for suspended solids concentration indicate that good mixing is being achieved. Results for suspended solids concentrations suggest that the anoxic zones are towards the upper limits recommended by literature for specific power dissipation. The duration for operation of mechanical mixers was investigated and identified that the duration could be reduced from 900 seconds down to 150 seconds. Alternative mixer positioning was also investigated and identified positioning which would increase the average flow velocity with decreased duration (150 seconds). The study identified that Council may achieve savings of $24,000 per year through optimisation of the mechanical mixers.

P-band radar remote sensing applied during the Airborne Microwave Observatory of Subcanopy and Subsurface (AirMOSS) mission has shown great potential for estimation of root zone soil moisture. When retrieving the soil moisture profile (SMP) from P-band radar, a mathematical function describing the vertical moisture distribution is required. Because only a limited number of observations are available, the number of free parameters of the mathematical model must not exceed the number of observed data. For example, a second order polynomial that contains 3 free parameters was presumed based on in-situ SMP data. The polynomial is currently parameterized based on 3 backscatter observations provided by AirMOSS (i.e. one frequency at three polarizations of HH, VV and HV). In this paper, a more realistic, physically-based SMP model containing 3 free parameters is derived based on a solution to Richards’ equation for unsaturated flow in soils. Evaluation of the new SMP model based on both numerical simulations and measured data revealed that it exhibits greater flexibility for fitting measured and simulated SMPs than the currently applied polynomial. It is also demonstrated that the new SMP model can be reduced to a second order polynomial at the expense of fitting accuracy.

: Microplastics and nanoplastics (MNPs) are becoming an increasingly severe global problem due to their widespread distribution and complex impact on living organisms. Apart from their environmental impact, the effects of MNPs on living organisms have also continued to attract attention. The harmful impact of MNPs has been extensively documented in marine invertebrates and larger marine vertebrates like fish. However, the research on the toxicity of these particles on mammals is still limited, and their possible effects on humans are poorly understood. Considering that MNPs are commonly found in food or food packaging, humans are primarily exposed to them through ingestion. It would be valuable to investigate the potential harmful effects of these particles on gut health. This review focuses on recent research exploring the toxicological impacts of micro- and nanoplastics on the gut, as observed in human cell lines and mammalian models. Available data from various studies indicate that the accumulation of MNPs in mammalian models and human cells may result in adverse consequences, in terms of epithelial toxicity, immune toxicity, and disruption of gut microbiota. The paper also discusses the current research limitations and prospects in this field, aiming to provide a scientific basis and reference for further studies on the toxic mechanisms of micro- and nanoplastics.

Bacterial resistance to antibiotics is a growing global concern, threatening human and environ-mental health, particularly among urban populations. Wastewater treatment plants (WWTPs) are thought to be “hotspots” for antibiotic resistance dissemination. The conditions of WWTPs, in conjunction with the persistence of commonly used antibiotics, may favor the selection and trans-fer of resistance genes among bacterial populations. WWTPs provide an important ecological niche to examine the spread of antibiotic resistance. We used heterotrophic plate count methods to identify phenotypically resistant cultivable portions of these bacterial communities and charac-terized the composition of the culturable subset of these populations. Resistant taxa were more abundant in raw sewage and wastewater before the biological aeration treatment stage. While some antibiotic resistant bacteria (ARB) were detectable downstream of treated wastewater re-lease, these organisms are not enriched relative to effluent-free upstream water, indicating effi-cient removal during treatment. Combined culture-dependent and culture-independent analyses revealed a stark difference in community composition between culturable fractions and the envi-ronmental source material, irrespective of culturing conditions. Higher proportions of the envi-ronmental populations were recovered than predicted by the widely accepted 1% culturability paradigm. These results represent baseline abundance and compositional data for ARB commu-nities for reference in future studies addressing the dissemination of antibiotic resistance associ-ated with urban wastewater treatment ecosystems.

The dye effluent is usually difficult to be degraded by conventional wastewater treatment in leather industry. In order to develop efficient and cost-effective treatment methods, we evaluate the effect of white-rot fungus immobilization for dye decolorisation in this paper. The Phanerochaete chrysosporium BKM-F-1767 was used for immobilization. This research found that the white-rot fungus immobilization had an obviously decolorisation effect in dye wastewater treatment, and plant carriers such as sorghum stalk and corn cob were helpful to the growth of Phanerochaete chrysosporium in white-rot fungus immobilization. Due to the stability and recyclability, the white-rot fungus co-immobilization was considered as the most suitable treatment for decolorisation of dye effluent which enjoyed the advantages of both adsorption immobilization and entrapment immobilization. Furthermore, the dye decolorisation evaluation was carried out to find the most suitable carrier for co-immobilization, and it found that sorghum stalk - calcium-alginate gel spherical particle (SS-CGPB) has better decolorisation effect than corn cobs - calcium-alginate gel spherical particle (CC-CGPB), and the dye decolorisation rate was 86.77%. After 5 cycles, the dye decolorisation rate was 85.87% which indicated the SS-CGPB preserved functional integrity successfully. By further analyzing the biodegradation process with white-rot fungus immobilization, the intermediate products were observed and the degradation pathway of acid golden yellow dye molecular was proposed. The results showed that the C-N single bonds attached to the central benzene in the dye molecule were attacked and destroyed in white-rot fungus co-immobilization treatment, thus the structure of dye molecule could be successfully degraded into small molecules which would be more easily treated by conventional treatment methods. Therefore, the white rot fungus co-immobilization might be appropriate for pre-treatment as an important biotechnology for the advanced treatment of dye effluent.

Water pollution in developing countries affects the public health of humans and the environment. It is therefore essential to develop environmentally friendly biopolymer, sustainable and low-cost membranes. Biopolymer nanofiber membranes are made by an electrospinning process of polylactic acid (PLLA) with additives. The main objective of this study is to manufacture biodegradable nanofiber membranes for use in filtering the suspended elements in wastewater at the level of drinkable or in agricultural fields. It is known that PLLA is brittle and therefore it is difficult to apply in industry. To solve this problem and enhance its flexibility. Flexible biopolymer polypropylene carbonate (PPC) and plasticizer are the addition in PLLA to reduce its glass transition and enhance its crystallization by adding Poly(3-hydroxy butyrate) PHB. In this work, 20 wt% of PPC was added to PLLA matrix to improve its elasticity and elongation at break. DSC shows that the addition of PPC, PHB, and TEC did affect the thermal properties like T_g, T_cc and T_m of the PLLA blends. The position of the T_g, T_cc, and T_m is shifting, the consequence the chain mobility is increased, therefore the crystallinity is enhanced. Electrospun fibers of PLLA/PPC/PHB/TEC were successfully manufactured. Tensile tester showed the increase in elongation at break of PLLA blend films, the elongation at break increases by 285 times. It observed with the increasing the elongation at break, a decrease in stress strength. After improving the mechanical properties with the higher elongation at break values, this blend is optimal for filtrations process.

Thermal plasma technique is becoming prominent in the treatment of variety of waste ranging from municipal solid waste, incinerator residue, hospital waste, electronics waste and industrial sludge. Application of the new treatment technology to petroleum sludge requires information on the nature and characteristics of the sludge that will be use to optimize the treatment system. In this investigation, petroleum sludge obtained from Petronas Melaka was characterized for its physical and chemical features. Proximate and ultimate analysis as well as determination of elemental composition were carried out. The sludge was found to contain high moisture (78.91%), low ash (5.06%), low volatiles (5.52%) and high fixed carbon (10.51%). The sludge has a TOC of 54.48% and HHV of 23.599MJ/kg. Despite the high moisture content, the higher heating value (HHV) is high when compared to literature values. The high value of HHV may be associated with the high fixed carbon, low ash content and high value of TOC. The apparent density of the sludge is slightly lower. Fourteen heavy metals are detected in significant quantities. Proper waste management that will safely dispose the sludge is required. The waste disposal technique should take into cognizant the possibility of leaching of heavy metals into ground water on one hand and the gasification of lighter ones on the other.

This work aimed to develop an anionic cellulose nanofiber (CNF) bio-adsorbent from palm date tree waste and to investigate its removal efficiency against cationic methylene blue dye from contaminated water. Palm date pulp was first prepared from palm date leaves through acid hydrolysis using H2SO4, followed by hydrolysis in a basic medium using KOH, in which the process completely removed the components of hemicellulose, lignin, and silica. To obtain anionic CNF, the resulting pulp was further treated with H2SO4, followed by centrifugation. Biogel formation of the CNF suspension was promoted by sonication, where its removal efficiency of methylene blue dye was studied as a function of dye concentration, temperature, contact time, and pH value. Two equilibrium models, the Langmuir and Freundlich models were employed, and the Langmuir model was found to be consistent with the experimental data. The highest removal efficiency was obtained at 60oC and was 5mg/gm. Furthermore, several kinetic models were used to gain insight into the adsorption mechanism. The pseudo-second-order model provided an accurate description of the adsorption process, while the Elovich equation suggested a chemical reaction between methylene blue dye and CNF. The study’s findings were in agreement with the pseudo-second-order model, indicating general chemical reactions. The study indicates that CNF adsorbents derived from renewable natural waste sources such as palm date leaves can be effective in removing cationic contaminants such as methylene blue dye.

Activated sludge process is a well known method to treat municipal and industrial waste water. In this complex process, the oxygen concentration in the reactors plays a critical role in the plant efficiency. This paper proposes the use of a Long Short-Term Memory (LSTM) network to identify an input-output model suitable for the design of an oxygen concentration controller. The model is identified from easy-accessible measures collected from a real plant. This dataset covers almost a month. The performances achieved with the proposed LSTM model are compared with the ones obtained with a standard AutoRegressive model with eXogenous input (ARX). Both models catch the oscillation and the overall behaviour (ARX ρ=0.833 , LSTM ρ=0.921), but, while the ARX model fails in reaching the correct amplitude (FIT=41.20%), the LSTM presents satisfactory performance (FIT=60.56%).

In the case of a Cu-Mo-W polymetallic ore, the wastewater from the scheelite cleaning flowsheet contains large amounts of residual flocculants and metal ions, and the separation of chalcopyrite and molybdenite require a large number of environmentally harmful depressants. Therefore, it is necessary to find new methods to reduce the environmental and cost pressures of wastewater treatment and the use of depressants. In this work, the flotation wastewater from scheelite cleaning flowsheet for the separation of chalcopyrite and molybdenite by selective surface passivation was investigated for the first time. Flotations of single minerals and artificially mixed minerals with or without immersion pretreatment in the presence and absence of aeration were performed. The results showed that pulp pH had no effect on the flotation of either mineral, and a molybdenite recovery of 93.22% with chalcopyrite recovery of 10.77% was achieved under the conditions of 10 days of immersion pretreatment with aeration, 350 mg/L of kerosene, and 100 mg/L of MIBC. By combining the electrochemical cyclic voltammetry analysis and characterization by XRD and SEM, the selective surface passivation mechanism of chalcopyrite was discussed, which could be due to the coverage of the insoluble oxidation products, especially jarosite. This work has simultaneously achieved the depressant-free flotation separation of molybdenite and chalcopyrite and the reuse of scheelite flotation wastewater, which is of great significance for environmental protection and cost saving.

The requirement for developing tools capable of detecting and monitoring heavy metals (HMs) has recently taken on more significance due to worries about their toxic effect on human health and aquatic habitats. In this study, a simple electrochemical sensing carbon paste electrode (CPE) based on composite of Zinc/Iron layered double hydroxide (LDH) and polyaniline (PANI) was developed for the determination of lead ions in aquatic solutions. For this purpose, Zn-Fe LDH/PANI was prepared and characterized by Fourier transform infrared (FTIR), X ray diffraction (XRD), and scanning electron microscopy (SEM). Modified carbon electrode based Zn-Fe LDH/PANI was electrochemically characterized compared with unmodified electrode in FCN as a redox probe using cyclic voltammetry (CV). Thus, Zn-Fe LDH/PANI was utilized as sensing material for the electrochemical determination of lead ions using differential pulse voltammetry (DPV). Zn-Fe LDH/PANI/CPE show limits of detection (LOD) and quantification (LOQ) of 167.8 nM and 559.4 nM, respectively. Zn/Mg/Fe LDH was prepared using co-precipitation method and characterized by XRD, FTIR, SEM and BET, used for removal of Pb+2 ions. Removal process was investigated at different conditions as pH, metal ion concentrations, starting adsorbent dose at first and contact time. Zn/Mg/Fe LDH was evaluated as an effective adsorbent material for lead ions elimination in aquatic solutions, with capacity of adsorption 700 mg/g. The elimination of lead ions on Zn/Mg/Fe LDH fitted the pseudo first-order kinetics model and the isotherm was matched with Langmuir model. Studies revealed that the ideal removal conditions were pH = 5.0, an adsorbent mass of 0.05 g, and 20 ml of 50 ppm metal ion concentration at 60 min. The Zn-Fe LDH/PANI composite also showed potential anti-cancer properties against lung cancer cells (A549) while maintaining safety for normal lung fibroblast cells (WI-38). Collectively, advancements in electrochemical sensors offer promising solutions for lead ion detection, with wide-reaching applications in wastewater treatment and cytotoxicity assessment. These innovations have the potential to enhance environmental monitoring and public health safety.

physicochemical methods was effective for the degradation of organics, but was highly hampered by the salt coexist in the complex wastewater matrix, resulting in low degradation dynamics. In this study, ZnO loaded carbon nitride (Zn-CNx) was synthesized and exhibited an excellent performance for 2,4-dichlorophenol (2,4-DCP) degradation (0.63 mg/L/min) in photcatalysis system. The doping of Zn into CNx contributed to the increased light absorption of the catalyst and the optimized electron transport pathways. The quenching experiment results proved that the superoxide radicals (·O2-) played a dominant role and hydroxyl radical (·OH) played a secondary role. Notably, the 2,4-DCP removal increased slightly with increasing salt content. As the initial pH increased from 3 to 11, the first-order degradation kinetic constants increased significantly, and the final pH was equilibrized in the range of 6.01-6.59. This study provided a high performance catalyst for photcatalysis and the mechanism for the effective degradation of 2,4-DCP under high salinity condition.

The presence of heavy metals in industrial effluents has recently become a source of concern for human health and the environment. Efficient removal of metal ions and wastewater treatment is essential for protecting public health and the environment. In this study, we present an eco-friendly, green synthesis of reactive and fully dispersed zerovalent iron nanoparticles (nZVI) in carbon nanofibers via an electrospinning technique. In this novel study, green tea (GT) was used as environmentally friendly, polyvinyl alcohol (PVA) was used for the stabilization and reduction of nZVI, and tetraethyl orthosilicate (TEOS) was added to provide flexibility and to increase the specific surface area of the nZVI based nanofibers. GT contains polyphenols, which act as reducing agents, converting iron ions into nZVI and the particles can then serve as the building blocks for the carbon nanofibers. TEOS can also contribute to the stability of the nZVI by coating their surfaces with a silica layer. This silica layer helps prevent the oxidation of the nZVI, thereby reducing their catalytic activity. The nZVI-based composite (∼ 400 nm) / carbonized (∼ 200 nm) nanofibrous mats were fully characterized by scanning electron microscopy. The average size of the nZVI embedded in the composite and carbonized nanofibers can range from 50 nm to 100 nm. The x-ray diffraction (XRD) analysis of nZVI-based carbon nanofibers showed that there is no crystallinity and a single-phase cubic structure. Both energy-dispersive X-ray spectroscopy (EDX) and Fourier transform infrared (FTIR) analysis also confirmed the formation of single-phase nZVI-based composite / carbonized nanofibers. The high intensity of the peaks in the FTIR spectrum indicates the formation of nZVI in the nanofibers structure. The electrospun nZVI-based carbon nanofibers have a higher surface area and better reactivity due to small particle size and large surface area-to-volume ratio. They can provide excellent water stability and dispersibility in water compared to bulk nZVI, which tend to agglomerate and settle quickly. Additionally, nanofiber morphology can enhance the mechanical strength and durability of the composite material. Due to low-cost synthesis and their high efficiency in removing pollutants, these nanofibers could be used as nano-filters for wastewater treatment.

This study develops into the application of a combined MFC unit with chemical coagulation for total treatment of inert contaminants in complex substrates. Microbial Fuel Cell (MFC) technology converts chemical energy in the form of organic matter, into bioelectricity in an environmentally friendly and effi-cient manner, reducing carbon emissions and increasing bioenergy production. An evaluation of a la-boratory scale chemical coagulation using an aluminum and poly-based coagulant on how effective it can remove bulk impurities such as particulate COD and turbidity to obtain the purest and most cost-effectively treated wastewater using a jar test is being conducted in this current study. This study aims to find the most effective treatment technologies for wastewater recovery in breweries in order to achieve zero liquid effluent discharge (ZLED). The preliminary results showed that adding a modest amount of poly and a 50 % alum alone treatment improved COD, color, and turbidity reduction. The turbidity removal efficiency achieved after chemical coagulation treatment was 90.50 % and 59.36 % COD removal, demonstrating the benefits of adopting an alum/poly based technique. To determine ZLED, this study clearly advised a combined treatment technique, specifically the MFC-flocculator unit for efficient organics and inorganics removal.

In an attempt to reuse fibrous textile waste and, at the same time, to address dye pollution in textile wastewater, waste cotton-based yarn was utilized as both a cheap and sustainable adsorbent and a precursor for carbon adsorbent production. Cotton and cotton/polyester yarn samples underwent thermal modification through carbonization followed by chemical activation with KOH. Various techniques including nitrogen adsorption-desorption isotherms, scanning electron microscopy, Fourier transform infrared spectroscopy, and surface charge determination were employed to analyze the morphological and surface properties of the cotton-based adsorbents. Adsorption properties were evaluated by testing the removal of selected cationic and anionic dyes from water. The impact of temperature, contact time, initial concentration, and pH of the adsorbate solution on adsorption was investigated, with experimental data analyzed using theoretical models. While carbonization alone did not significantly enhance adsorption properties, activated samples exhibited high efficacy in removing both cationic and anionic dyes from water. Despite the negative influence of the polyester component in the carbon precursor on the efficiency of activated samples in removing methyl orange, results indicated that activated cotton and cotton/polyester yarn could be used to prepare highly efficient adsorbents for the rapid removal of methylene blue from real wastewater samples.

Wastewater-Based Epidemiology (WBE) is currently used to monitor not only the spread of the pandemic virus SARS-CoV-2 but also for other viruses in endemic conditions, particularly in the absence of syndromic surveillance. Continuous monitoring of sewage requires high costs and significant time investment, highlighting the need for standardized methods and structured monitoring strategies. In this context, we conducted weekly wastewater monitoring in northwestern Italy, targeting Human Adenovirus (HAdV), Norovirus Genogroup II (NoVggII), Enterovirus (EV), and SARS-CoV-2. Samples collected at the entrance of treatment plants were concentrated using PEG/NaCl precipitation and viral nucleic acids were extracted and detected by real-time (RT-)qPCR. NoVggII resulted the most identified target (84.4%), followed by HAdV, SARS-CoV-2, and EV. Only HAdV and EV exhibited seasonal peaks in spring and summer. SARS-CoV-2 results compared with data previously collected in the same study area (February 2021 to September 2021) revealed a shift from an epidemic to a pandemic status, likely due to the evolution of variants. In conclusion, WBE, using standardized methods and an efficient monitoring strategy, proves valuable for virus surveillance in pandemic and epidemic scenarios, enabling the identification of temporal-local distribution patterns that are useful for making informed public health decision.

Micropollutants belongs to various groups of chemicals. One of the most diverse and large group of them are pharmaceuticals. The presence of pharmaceutical residues in wastewater poses a significant challenge to water quality and environmental health. This paper provides an overview of recent advancements in the removal of pharmaceuticals from water, focusing on various treatment processes and their effectiveness in eliminating micropollutants. Through a review of literature, including studies on ozonation, UV irradiation, sulphate radical-based tech-nologies, and photocatalytic processes, insights into degradation mechanisms and optimal con-ditions for their removal are synthesized. Additionally, with new legislation mandating the monitoring of selected micropollutants and the implementation of quaternary treatment in wastewater treatment plants, the paper discusses prospects for future research and recommen-dations for effective pharmaceuticals removal. Key actions include conducting comprehensive laboratory and pilot trials, implementing quaternary treatment of wastewaters, continuously monitoring of water quality, investing in research and development, and promoting collabora-tion and knowledge sharing among stakeholders. By embracing these strategies, we can work towards safeguarding water resources and protecting public health from the adverse effects of pharmaceutical contamination.

Nanoscience is a rapidly growing science stream that has been one of the cost-effective and energy-efficient approaches with wide applications. Water pollution is a major issue that is increasing continuously due to anthropogenic activities and several organic and inorganic contaminants. To overcome this issue, nanoparticles (NPs) have been successfully used to treat water. These NPs possess many beneficial applications in many fields like agriculture, cosmetics, photoconductors, environmental biotechnology, glass and alloy production, solar cells, nanomedicine and drug deliveries, biosensors, food industries, etc. The properties comprising high surface area, greater chemical reactivity, and mechanical properties play a vital role in imparting such beneficiary properties. As a result, there has been an increasing demand for the synthesis of NPs. However, excess usage of NPs further creates toxic by-products. Therefore, scientists and researchers are now focussing on the biogenic synthesis of NPs. The biological routes of NP synthesis have been crucial because they are eco-friendly and environmentally safe. This chapter highlights the usage of different approaches and biogenic sources for the production of NPs. It also discusses the recent advancement in the use of biogenic NPs with respect to applications for wastewater treatment.

The European Union Green Deal aims at curbing planet-warming greenhouse gas emissions and introducing clean energy production. But to achieve energy efficiency, the opportunity cost of different energies must be assessed. In this article, we analyse two different systems for the treatment of wastewater that, at the same time, produce energy for its own operation. On the one hand, high-rate algal ponds system (HRAP) is considered; on the other hand, we study a conventional activated sludge system which uses photovoltaic power (AS+PV). This paper offers a viability analysis of both systems based on the capacity to satisfy their energetic consumption. In order to assess this viability, the probability of not achieving the energy consumption threshold at least one day is studied. The results point that the AS+PV system self-sufficiency is achieved using much lesser surfaces than those of HRAP system (for the former, less than 6.500 m2, for the latter 40.000 m2). However, the important AS capital cost makes still the HRAP system more economic, although storage provides a great advantage for using the AS+PV in locations where we have a lot of irradiance. This viability analysis, along with the opportunity cost analysis, will be used to assess these two projects devoted to the treatment of wastewater.

Snakebite envenomation, cognized as a neglected tropical disease, is a dread public health concern with the most susceptible groups being herdsmen, the elderly, active farmers, hunters, fishers, firewood collectors, 10 to 14-year old working children and individuals with limited access to education and health care. Snakebites are fragmentarily documented in Uganda primarily because most occur in rural settings where traditional therapists end up being the first line defence for treatment. Ethnobotanical surveys in Uganda have unveiled that some plants are used to antagonize the activity of various snake venoms. This review was sought to compile the sporadic information on the vegetal species reported as antivenins in Uganda. Electronic data indicate that no study entirely reported on antivenin plants in Uganda. A total of 77 plant species belonging to 65 genera, distributed among 42 botanical families claimed as antiophidic in Uganda are used for treatment of snakebites. Majority of these species belong to family Fabaceae (30.9%), Euphorbiaceae (14.3%), Asteraceae (11.9%), Amaryllidaceae (9.5%) and Solanaceae (9.5%). The antiophidic species listed are shrubs (40.5%), trees (32.9%) and herbs (17.7%), usually found in the wild and uncultivated. Antivenin extracts are primarily prepared from roots and leaves, through decoctions, infusions, powders and juices and administered orally or topically. The most frequently encountered therapeutically important species are Allium cepa L., Carica papaya L., Securidaca longipedunculata Fres., Harrisonia abyssinica Oliv. and Nicotiana tabacum L. Baseline epidemiological data on snake envenomation and antivenin plants in Uganda remain incomplete due to inadequate research and diverse ethnic groups in the country. There is a dire need to isolate and characterize the bioactive compounds in the claimed plants to enable their adroit utilization in handling the plague of snake envenomation. More baseline data should be collected on snake ecology and human behaviour as well as antivenin plants in Uganda. Indigenous knowledge on the use of plant preparations in traditional medicine in Uganda is humongous, but if this is not quickly researched and appropriately documented, indications as to the usefulness of this vegetal treasure house will be lost in the not so distant future.

Oilseed plants of the Brassicaceae plant family are cultivated for food, feed and industrial purposes on large-scale in Europe. This review gives an overview of current market-oriented applications of new genomic techniques (NGTs) in relevant Brassicaceae oilseed crops based on a literature survey. In this respect, changes in oil quality, yield, growth and resistance to biotic and abiotic stress are goals in oilseed rape (B. napus) and camelina (C. sativa). Environmental risk assessment scenarios are developed for specific NGT applications in Brassicaceae oilseed crops with either a changed oil composition or with fitness related traits. In case of a changed oil composition an increase or decrease of polyunsaturated fatty acids (PUFA) demonstrates risks for health and survival of pollinators. In case of fitness related traits other risks were identified, i. e. an increased risk of spread and persistence of NGT plants. Furthermore, there are indications for potential disturbance of interactions with the environment, involving signalling pathways and reaction to stress conditions. It is shown that for a comprehensive risk assessment the technological potential of NGTs, the plants’ biology and the scale of releases have to be considered in combination. Therefore, the release of NGT plants into the environment for agricultural purposes will require risk assessment and monitoring of single traits as well as of combinatorial and long-term cumulative effects. In addition, risk management should develop concepts and measures to control and potentially restrict the scale of releases. This is especially relevant for NGT Brassicaceae in Europe which is a centre of diversity of this plant family.

The only solution to avoid pollution due to sewage is to treat the effluent and reuse water and sludge at the wastewater production site. This makes it necessary to install treatment plants distributed along the sewer system to prevent the movement of effluents with the consequent losses to the aquifer. This new management is called decentralized wastewater treatment. To make this change possible, it is necessary to develop treatment plants that do not represent a health hazard for citizens, eliminating the nuisance caused by traditional plants. These plants need to be robust, operate autonomously, have reduced maintenance and exhaustive control of each process, where each cubic meter of effluent is perfectly controlled, avoiding losses to the aquifer or discharges that may occur due to deficiencies in their purification capacity; constantly producing water and sludge, which are directly reusable with all the health and environmental guarantees regardless of variations in inlet effluent or environmental conditions. This article presents a paradigmatic case of a decentralized solution with conditions of maximum complexity that has been solved efficiently, saving around 98% of the initial investment, completely avoiding wastewater discharges into the environment and reusing 100% of the treated water, in 14 years of operation.

The utilization of titanium dioxide (TiO2) as a photocatalyst for the treatment of wastewater has attracted significant attention in the environmental field. Herein, we have prepared a NH2-MIL-125-derived TiO2@N-doped C Visible Light Catalyst through an in-situ calcination method. The nitrogen element in the organic connector is released through calcination, simul-taneously doping into the sample, thereby enhancing its spectral response to cover the visible region. The as-prepared TiO2@N-doped C catalyst exhibited preserved cage structure even after calcination, thereby alleviating the optical shielding effect and further augmenting its photo-catalytic performance by increasing the reaction sites between the catalyst and pollutants. The calcination time of the TiO2@N-doped C-450 °C catalyst was optimized to achieve a balance be-tween the TiO2 content and nitrogen doping level, ensuring efficient degradation rates for basic fuchsin (99.7%), Rhodamine B (89.9%), and tetracycline hydrochloride (93%) within 90 minutes.

The efficiency of microbial inactivation in water is highly dependent on the type of treatment technology used as well as the characteristics of the water to be treated. Wastewater from poultry slaughterhouses carries a significant number of microorganisms posing threat to humans and the environment in general. Therefore, the treatment of poultry slaughterhouse wastewater requires the use of appropriate purification systems with high removal efficiency for microbial agents. In this study, the performance of an integrated treatment plant with electrolysis, ultrafiltration, and ultraviolet radiation as the principal treatment units is investigated in terms of microbial inactivation from poultry slaughterhouse wastewater. In this case, Total microbial number, Total coliform bacteria, Thermo-tolerant coliform bacteria, Pathogenic flora, including Salmonella coliphages, Spores of sulfite-reducing clostridia, Pseudomonas aeruginosa, and Staphylococcus aureus Enterococcus were studied. About 63.95% to 99.83% of the microbes were removed by the EC treatment unit, as well as 99.86% to 100% removal efficiency was achieved after the combined treatment. However, the Pseudomonas aeruginosa was the only microbial agent detected in the final effluent after the combined treatment. The phenomenon suggests that an upgrade to the treatment plant may be required to achieve 100% removal assurance for Pseudomonas aeruginosa.

The efficiency of microbial inactivation in water is highly dependent on the type of treatment technology used as well as the characteristics of the water to be treated. Wastewater from poultry slaughterhouses carries a significant number of microorganisms posing threat to humans and the environment in general. Therefore, the treatment of poultry slaughterhouse wastewater requires the use of appropriate purification systems with high removal efficiency for microbial agents. In this study, the performance of an integrated treatment plant with electrolysis, ultrafiltration, and ultraviolet radiation as the principal treatment units is investigated in terms of microbial inactivation from poultry slaughterhouse wastewater. In this case, Total microbial number, Total coliform bacteria, Thermo-tolerant coliform bacteria, Pathogenic flora, including Salmonella coliphages, Spores of sulfite-reducing clostridia, Pseudomonas aeruginosa, and Staphylococcus aureus Enterococcus were studied. About 63.95% to 99.83% of the microbes were removed by the EC treatment unit, as well as 99.86% to 100% removal efficiency was achieved after the combined treatment. However, the Pseudomonas aeruginosa was the only microbial agent detected in the final effluent after the combined treatment. The phenomenon suggests that an upgrade to the treatment plant may be required to achieve 100% removal assurance for Pseudomonas aeruginosa.

The environmental policy is compelling industries to treat their wastewater to a level that can be released into the domestic sewer system or even for reuse. However, many industrial branches are lacking space for traditional wastewater plant. Hence, electrokinetics wastewater treatment is a viable alternative as it is fast and does not require large space. However, the electrokinetics wastewater treatment is still mostly tested in the laboratory. In the current study, a prototype of electrokinetics wastewater treatment industrial-size device has been designed, constructed and tested under real conditions. In this paper the device is described and the results obtained from the operation of the device are presented and discussed.

Antiviral drugs cannot treat dengue fever, a serious medical disease spread by the Aedes aegypti and Aedes albopictus mosquitoes. One important arbovirus disease is dengue fever. Safe, affordable and effective drugs that inhibit dengue virus (DENV) are needed to control dengue worldwide. Medicinal plants have long been considered an important alternative in the treatment of various diseases, including dengue fever. The aim of this study was to use databases PubMed, Google Scholar and Research Gate to identify plants of different tribes from different places that can be used for the treatment of DENV infection and open supportive care for dengue. Previous studies have shown antiviral activity of medicinal plants against DENV. The aim of the present study is to discover plants from different tribes from different places that can be used to treat DENV infection and provide open supportive care against dengue. The recommended reporting guidelines for systematic reviews and meta-analyses (PRISMA statement) were followed in the search and selection of articles using the PubMed database, Google Scholar and Research Gate. The final selection was made after careful consideration and up to 85 publications that met the inclusion criteria. It is said that different plants from different tribes and geographical locations can be used to treat DENV infection.

In the era of mounting water scarcity, particularly in arid regions, the agricultural sector is striving to optimize the water resource management practices. Treated wastewater (TWW) has emerged as a viable alternative to freshwater for irrigation, offering a sustainable solution to water conservation. However, ensuring the safety and quality of TWW is paramount to safeguard for both crop health and environmental integrity. Electrical conductivity (EC), a critical factor in assessing TWW suitability for irrigation, can significantly impact crop yields and soil health since it is directly linked to the concentration of dissolved salts and ions. Therefore, this study delves into the development of advanced predictive models for EC assessment by employing supervised machine learning (ML) techniques like the Support Vector Regression (SVR), Adaptive Network-based Fuzzy Inference System (ANFIS), and Multiple Linear Regression (MLR). The TWW samples collected from Al-Qatif area, Saudi Arabia were assessed in the lab through a sensor-based real-time monitoring system integrated with Internet of Things (IoT) network and a multiprobe device. The key water quality parameters assessed involved, temperature (T), pH, Oxidation Reduction Potential (ORP), Resistivity (RES), Total Dissolved Solids (TDS), Salinity and Turbidity which served as the foundation for these models, given their profound influence on and their anticipated impact on EC levels. Following feature selection, two distinct model combinations were identified for the SVR, ANFIS and MLR models. Furthermore, to evaluate prediction performance, four statistical criteria, including coefficient of determination (R²), correlation coefficient (R), mean square error (MSE), and root mean square error (RMSE), were employed. Overall, the comparative performance results proved that ANFIS-M2 indicated the strongest predictive capability with the R² value of 0.99572 and 0.75145 and the RMSE values of 0.00965 and 0.01134, respectively in both calibration and verification stages.

This study investigated the adaptability of Dunaliella salina to different salinity levels, with emphasis on growth, pigment concentration, and desalination potential. It was found that among the 21 salinity levels, salinity 75 produced consistently favorable results in cell count (13.08 x 10³ ± 1.41 x 10³ cells/mL), dry biomass (2.46 ± 0.06 g/L), pigment content (chlorophyll a = 97.5 ± 0.1 µg/L, chlorophyll b = 123.6 ± 0.3 µg/L), and desalination (9.32 ± 0.47 reduction). Therefore, salinity 75 was selected for the final trial (scale-up), which revealed unanticipatedly high cell counts (58.96 x 10³ ± 535.22 cells/mL), with dry biomass weight being statistically different (higher) than the expected (4.21 ± 0.02 g/L) (p<0.0001), most likely due to high cell count and energy reserve storage for high salinity adaption in the form of bio-compounds. Pigment growth continued (chlorophyll a = 95.4 ± 2.2 µg/L, chlorophyll b = 128.1 ± 5.1 µg/L), indicating pigment production under salt stress. Notably, desalination did not occur in this stage, possibly due to the necessity for a bigger initial inoculate, prolonged exposure or bioaccumulation becoming the prevailing mechanism over desalination. Nevertheless, the trial highlights D. salina's strong adaptation to various salinity levels. This suggests a promising future in halophyte research, particularly in understanding the mechanisms that prevent salt accumulation in cells and how to overcome this barrier. Additionally, these results suggest that microalgae could be a viable resource in saline-rich environments unsuitable for conventional agriculture, promoting industrial adaptation to adverse conditions.

This work shows the potential of a new way of co-treatment of domestic wastewater (DWW) and a liquid stream coming from the thermal hydrolysis of the organic fraction of municipal solid waste (OFMSW) mediated by a mixed culture of purple phototrophic bacteria (PPB) capable of assimilating carbon and nutrients from the medium. The biological system is an open single-step process operated under microaerophilic conditions at an oxidative reduction potential (ORP) &lt; 0 mV with a photoperiod of 12/24 h and fed during the light Stage only, so the results can be extrapolated to outdoors open ponds operation by monitoring the ORP. The effluent mostly complies with the discharge values of the Spanish legislation in COD and P values (&lt;125mg/L &lt;2 mg/L), respectively, and punctually on values in N (&lt;15mg/L). Applying an HRT of 3 d and a ratio of 100:7 (COD:N), the presence of PPB in the mixed culture surpassed 50% of 16S rRNA gene copies, removing 78% of COD, 53% of N and 66% of P. Furthermore, increasing the HRT to 5 d, removal efficiencies of 83% of COD, 65% of N and 91% of P were achieved. In addition, the reactors were further operated in a membrane bioreactor, thus separating the HRT from the SRT to increase the specific loading rate. Very satisfactory removal efficiencies were achieved by applying HRT and SRT of 2.3 and 3 d, respectively: 84% of COD, 49% of N and 93% of P despite low presence of PPB due to more oxidative conditions, which anyway step-by-step re-colonized the mixed culture until reaching &gt;20% of 16S rRNA gene copies after 49 d of operation. These results open the door to scale up the process in open photobioreactors capable of treating urban wastewater and municipal solid waste in a single stage and under microaerophilic conditions by controlling the ORP of the system. This novel urban biorefinery allows reducing treatment costs of two urban wastes and embed them in the circular bioeconomy through water recycling and valorizing PPB biomass as a source of carbon, nitrogen and phosphorus.

The purpose of this study is nutrient resources recovery by achieving the optimal chemical oxygen demand (COD) and carbon to nitrogen ratio (C/N) in co-composting wastewater treatment plant sludge with Municipal Solid Wastes (MSW). In this effort, the co-composting has been conducted in form of a case study in the northern region of Iran. In this research, 192 tests were carried out on four series of samples examined in terms of waste to sludge ratio, different aeration period, the percent of porous materials and the moisture content. This study was carried out at a temperature of 50 °C for a 15 day period by application of the in-vessel system and shows that the best ratio for waste to sludge is 2:1, while the 8 hour period is the best aeration period. The porous material which can be added to the composting process is limited to 15% in weight. In other words, any more or less amount of this material will adversely impact the process. Moreover, this research suggests that the sludge dewatering is not required in such processes. In Addition, the efficiency of both COD and C/N reductions equals to about 40%.

Microbial electrochemical technologies (MET) rely on the presence of the metabolic activity of electroactive bacteria for the use of solid-state electrodes for oxidizing different kind of compound, that could lead to the synthesis of chemicals, bioremediation of polluted matrices, the treatment of contaminants of interest, as well as the recovery of energy. Keeping in mind those possibilities, since the beginning of the present century, there has been a growing interest in the use of electrochemical technologies for wastewater treatment, and if possible with simultaneous power generation. In the last years, there has been a growing interest to explore the possibility of merging MET with constructed wetlands, to offer a new option of intensified wetland system that could keep a high performance with a lower footprint. Based on that interest, this paper explains the general principles of MET, and the different known extracellular electron transfer mechanisms ruling the interaction between electroactive bacteria and potential solid-state electron acceptors. Also, the adoption of those principles for the development of MET set-ups for simultaneous wastewater treatment and power generation, and the challenges that the technology face. Ultimately, the most recent developments in set-ups that merges MET with constructed wetlands are presented and discussed.

Annually, millions of people worldwide are affected by skin diseases, and current therapeutic approaches have limited efficacy. Advances in the treatment of exosomes have led to the development of new therapeutic methods that hold promising potential for improving the treatment options for skin diseases. The aim of this study is to produce pharmaceutical and cosmetic compounds based on exosomes for the treatment of skin conditions such as eczema, pigmentation disorders, skin sagging and aging, cellular skin regeneration, increased skin moisture, and prevention of skin shedding, among others. This study examines the effects of exosomes derived from plants, humans, medicinal algae, and fungi to treat skin diseases. Spectrophotometric analysis reveals the presence of nucleic acids and proteins in exosome samples, indicating their cargo composition. TEM micrographs demonstrate that the exosome isolation process preserves the integrity of the membrane and the crucial spherical structure for their functionality. DLS analysis confirms that isolated exosomes have a size similar to typical exosome dimensions. MTT assays indicate concentration-dependent cytotoxic effects of exosomes on skin cells, with a calculated IC50 representing a significant decrease in cell viability. Real-time PCR shows higher gene expression levels of collagen I and collagen III, indicating the potential of exosomes to enhance collagen synthesis. Tyrosinase enzyme expression analysis demonstrates the influence of exosome treatments on pathways related to melanin production. The use of exosomes derived from various sources provides a promising platform for developing new drugs in the treatment of skin diseases. Additionally, exosomes can be utilized in the treatment of autoimmune diseases and cancer, transforming them into a hopeful field of research. Plant-derived exosomes are environmentally friendly and can serve as the next generation of drug delivery systems for treating various diseases.

We construct a Bayesian estimator for the dilution of a wastewater sample. When wastewater is diluted by rainwater an estimate of the level of dilution is required if we are to normalise sample measurements of disease markers such as SARS-CoV-2 RNA. We consider the situation where flow measurements are available, but will regularly be unreliable because of the action of combined sewer outflows (CSOs) and wastewater storage tanks, which divert wastewater away from treatment plants when the flow is excessive. However, we also have proxies for the flow from various chemical markers (e.g.\ phosphate, ammonium, electrical conductivity), whose level per unit of population is fixed. The new flow estimator has multiple advantages compared to existing procedures: credible intervals for the estimates; optimal weighting of the chemical markers; systematic handling of missing and censored values; and model based smoothing without lags.

According to the eminent scholar, philosopher, and physician Avicenna, "the doctor has three tools: the word, the plant, the knife." The plant kingdom is recognized as humanity's earliest and most ancient healing source, employed for the management and prevention of illnesses. Tracing back through history, the most ancient documented proof of plants' utilization in medicine dates back to a Sumerian clay slab discovered in Nagpur roughly 5000 years ago. This artifact included a compilation of twelve medicinal recipes that involved over 250 diverse plant species. Sumerian healers extracted powders and infusions from plant roots and stems, while also crediting healing properties to pears and figs. Additionally, they utilized dried and ground young shoots of willow and plum trees, pine and fir needles as a component in compresses and poultices. Often, powders from animal and mineral sources were blended with those extracted from dried and crushed plants. Notably, in addition to water, wine and beer served as solvents. Thus, at least 80 centuries ago, people utilized the most uncomplicated medicinal plant-based preparations for treatment [1]. The "Pen T'Sao," an ancient Chinese text on roots and herbs, authored by Emperor Shen Nung approximately 2500 BC, contains descriptions of 900 medicaments (comprising dried components of medicinal plants). Several of these substances are still in use today, including Rhei rhisoma, camphor, Theae folium, Podophyllum, great yellow gentian, ginseng, datura, cinnamon bark, and ephedra [2]. Regarding Kazakh folk medicine, an area that has yet to be fully explicated and substantiated, it can be stated that the traditional medicinal knowledge of the Kazakh people transcends the mere treatment of ailments and rests on robust theoretical underpinnings. Oteiboydak Tleukabyluly (1388-1478), an astute healer and prominent figure in Kazakh folk medicine during the 15th century, comprehensively explicated the secrets of the healing art in his medical and ethnographic work "Medical Narrative," which he composed between 1466 and 1473 at the behest of az-Zhanibek Khan, who held him in high esteem as a great healer. This medical encyclopedia delineates the functions of various organs of the human body and provides a catalogue of the primary diseases associated with them. Furthermore, it includes a meticulous description of the methods used in traditional medicine at present, such as setting bones, listening to the pulse, and incantations. Through practical experimentation and experimentation conducted in the steppe laboratory, the healer formulated a total of 1,108 different medicinal compounds, of which 858 were derived from medicinal plants, 318 were extracted from animal organs, and roughly 60 were sourced from metals. The moniker "Teacher without a teacher" was bestowed on Oteiboydak Tleukabylov, who discovered methods for treating 1,050 different diseases [3]. At present, the employment of phytotherapy has gained widespread acceptance on a global scale. According to the World Health Organization's (WHO) global review of national policies concerning traditional, complementary, and alternative medicine, as well as the regulation of herbal medicines, there is an evident growth in the European and Asian market for herbal medicines [4]. Kazakhstan boasts a natural flora of over 6,000 plant species [5]. The exact number of medicinal plant species present in Kazakhstan remains uncertain, as the list continues to expand annually. More than 150 plant species have been employed in both official and folk medicine for various ailments. This review focuses on a selection of medicinal plants growing within the territory of the Republic of Kazakhstan that have traditionally been used to alleviate skin diseases. In conducting this study (2010-2023), emphasis was placed on the plants' phytochemical composition, with a particular focus on the principal components responsible for their therapeutic effects against inflammatory skin conditions such as dermatitis, atopic dermatitis, and eczema.

Retiring coal power plants can reduce air pollution and health damages. However, the spatial distribution of those impacts remains unclear due to complex power system adjustments and pollution chemistry and transport. Focusing on coal retirements in Pennsylvania (PA), we analyze six counterfactual scenarios for 2019 that differ in retirement targets (e.g., reducing 50% of coal-based installed capacity vs. generation) and priorities (e.g., closing plants with higher cost, closer to Environmental Justice Areas, or with higher CO₂ emissions). Using a power system model of the PJM Interconnection, we find that coal retirements in PA shift power generation across PA and the Rest of PJM region leading to scenario-varying changes in the plant-level release of several air pollutants. Due to air pollution chemistry and transport and socio-demographics, these changes in turn give rise to a reduction of 10 to 182 PM_2.5-attributable deaths in PJM across the six scenarios, with most reductions occurring in PA. Scenarios that reduce more coal power generation yield greater aggregate health benefits due to air quality improvements in PA and adjacent downwind regions. In addition, vulnerable populations—in both PA and Rest of PJM—benefit most in scenarios that prioritize plant closures in PA near Environmental Justice Areas. These results demonstrate the importance of considering cross-regional linkages and socio-demographics in designing equitable retirement strategies.

Preventive Maintenance (PM) is a periodic maintenance strategy, which has great results for devices in extending their life, increasing productivity, and most importantly, help avoid unexpected breakdowns and their costly consequence. A preventive maintenance scheduling (PMS) is determining the time for carrying out PM, and it represents a sensitive issue in terms of impact on production if the time for the PM process is not optimally distributed. In this study, hybrid heuristic methods were used to solve the PMS problem, as genetic algorithm and Tabu research were adopted. The optimal solution was reached in a short time compared to previous studies in which optimal methods were used, integer programming and nonlinear integer programming. Also, sensitivity analysis was applied to measure the robustness and strength of the method used, where an optimal solution was obtained for all experiments and in record time. This method can be used for power plants in privet or public sectors, to generate an optimal PMS, to save money, and to avoid water or electricity cuts.

The Australian tropical montane cloud forest (TMCF) is home to approximately 18 percent of the nation’s total vascular plant species. Over the past century, human activity and industrial development have caused global climate changes, posing a severe and irreversible danger to the entire land-based ecosystem, and WTWHA is no exception. The current average annual temperature of WTWHA in FNQ is 24 °C. However, in the coming years (by 2030), the average annual temperature increase is estimated to be between 0.5 and 1.4 °C compared to the climate observed between 1986 and 2005. Looking further ahead to 2070, the anticipated temperature rise is projected to be between 1.0 and 3.2 °C, with the exact range depending on future emissions. We identified 84 plant species endemic to the WTWHA in FNQ, which are already experiencing climate change threats. Few of these plants are used in herbal medicines. This study comprehensively reviewed metabolomics studies conducted on these 84 plant species until now toward understanding their physiological and metabolomics responses to global climate change. This review also discusses: i) recent developments in plant metabolomics studies that can be applied to study and understand the interactions of wet tropical plants with climatic stress, ii) medicinal plants and isolated phytochemicals with structural diversity, and iii) reported biological activities of crude extracts and isolated compounds.

It is difficult to capture the real-time online measurement data for biochemical oxygen demand (BOD) in wastewater treatment processes. An optimized extreme learning machine (ELM) based on an improved cuckoo search algorithm (ICS) is proposed in this paper for the design of soft BOD measurement model. In ICS-ELM, the input weights matrices of the extreme learning machine (ELM) and the threshold of the hidden layer are encoded as the cuckoo's nest locations. The best input weights matrices and threshold are obtained by using the strong global search ability of improved cuckoo search (ICS) algorithm. The optimal results can be used to improve the precision of forecasting based on less number of neurons of the hidden layer in ELM. Simulation results show that the soft sensor model has good real-time performance, high prediction accuracy and stronger generalization performance for BOD measurement of the effluent quality compared to other modeling methods such as back propagation (BP) network in most cases.

Genetic engineering has become an essential element in developing climate-resilient crops and environmental sustainable solutions to respond to the increasing need for global food security. Genome editing using CRISPR/Cas [Clustered regulatory interspaced short palindromic repeat (CRISPR)-associated protein (Cas)] technology is being applied to a variety of organisms, including plants. This technique has become popular because of its high specificity, effectiveness, and low production cost. Therefore, this technology has the potential to revolutionize agriculture and contribute to global food security. Over the past few years, increasing efforts have been seen in its application in developing higher-yielding, nutrition rich, disease resistant, stress-tolerant “crops” fruits and vegetables. Cas proteins such as Cas9, Cas12, Cas13, and Cas14, among others, have distinct architectures and have been used to create new genetic tools that improve features that are important for agriculture. The versatility of Cas has accelerated genomic analysis and facilitated the use of CRISPR/Cas to manipulate and alter nucleic acid sequences in cells of different organisms. This review provides the evolution of CRISPR technology exploring its mechanisms and contrasting it with traditional breeding and transgenic approaches to improve different stress tolerance. We have also discussed the CRISPR/Cas system and explored three Cas proteins that are currently known to exist: Cas12, Cas13, and Cas14 and their potential to generate foreign DNA free or non-transgenic crops that could be easily regulated for commercialization in most countries.

Levels of synthetic musk fragrances (SMFs) and various personal care products (PCPs) were measured in the Han River and its tributaries in Seoul, Korea. The most abundant SMF in all river and PCP samples was 4,6,6,7,8,8-hexamethyl-1,3,4,7-tetrahydrocyclopenta[g]isochromene (HHCB), followed by 1-(3,5,5,6,8,8-hexamethyl-6,7-dihydronaphthalen-2-yl)ethanone (AHTN), musk ketone (MK), and 1,1,2,3,3-pentamethyl-2,5,6,7-tetrahydroinden-4-one (DPMI). There was a significant correlation between the SMF concentration in the PCPs and the Han River samples. Moving from upstream to downstream in the Han River, the median SMF concentration was 6.756, 2.945, 0.304, and 0.141 μg/L in the sewage treatment plant (STP) influent, effluent, tributaries, and mainstream, respectively, implying that effective SMF removal was achieved during the sewage treatment process, followed by dilution in the receiving water. Four STPs using advanced biological treatment processes had removal efficiencies of 55.8%, 50.6%, 43.3% for HHCB, AHTN, and MK, respectively. The highest SMF concentrations in the tributaries were observed at locations close to the STPs. Our study confirmed that the main source of SMFs in the receiving water were sewage effluent containing untreated SMFs, which are largely originated from household PCPs, especially hair care products (e.g., shampoo) and perfumes.

Vertical Indoor Farming (VIF) with hydroponics offers a promising perspective for sustainable food production. Intelligent control of VIF system components plays a key role in reducing operating costs and increasing crop yields. Modern machine vision (MV) systems use Deep Learning (DL) in combination with camera systems for various tasks in agriculture, such as disease and nutrient deficiency detection, and flower and fruit identification and classification for pollination and harvesting. This study presents the applicability of MV technology with DL modelling to detect the growth stages of chilli plants using YOLOv8 networks. The influence of different bird’s eye and side view datasets and different YOLOv8 architectures was analysed. To generate the image data for training and testing the YOLO models, chilli plants were grown in a hydroponic environment and imaged throughout their life cycle using four camera systems. The growth stages were divided into growing, flowering and fruiting classes. All trained YOLOv8 models showed reliable identification of growth stages with high accuracy. The results indicate that models trained with data from both views show better generalisation. YOLO’s middle architecture achieved the best performance.

Tellurium exhibits exceptional intrinsic electronic properties. However, investigations into the modulation of tellurium's electronic properties through physical modification are notably scarce. Here, we present a comprehensive study focused on the evolution of the electronic properties of tellurium crystal flakes under plasma irradiation treatment by employing conductive atomic force microscopy and Raman spectroscopy. The plasma-treated tellurium experienced a process of defect generation through lattice broken. Prior to the degradation of electronic transport performance due to plasma irradiation treatment, a remarkable observation emerged: in the low-energy region of hydrogen plasma-treated tellurium, a notable enhancement in conductivity was unexpectedly detected. The mechanism underlying this enhancement in electronic transport performance was thoroughly elucidated by comparing it with the electronic structure induced by argon plasma irradiation. This study not only fundamentally uncovers the effects of plasma irradiation on tellurium crystal flakes, but also unearths an unprecedented trend of enhanced electronic transport performance at low irradiation energies when utilizing hydrogen plasma. This abnormal trend bears significant implications for guiding the prospective application of tellurium-based 2D materials in the realm of electronic devices.

Developing countries are confronted with general issues of municipal wastewater management and treatment. Untreated faecal sludges and wastewaters from septic tanks and traditional toilet are rejected into rivers and sometimes using for urban agriculture without any treatment to reduce the biorisk. Consequently, there are potential environmental and public health risks. In this study, a wastewater treatment plant prototype coupled with Moringa Oleifera seeds treatment was developed to evaluate their effectiveness for the reduction of faecal indicator bacteria and antibiotics resistant bacteria in domestic wastewater. Results indicate that our performed prototype system presents high capacity to reduce bacteria with abatements up to 99.34%. High reductions of bacteria load were obtained after add of Moringa Oleifera seeds into waters, with reductions varied from 36.6-78.8% for E. coli, 28.3-84.6% for Faecal coliform, 35.3-95.6% for Vibrio cholerae and 32.1-92.4% for total flora. Same effects of Moringa Oleifera seeds were noted for reducing antibiotic resistant bacteria, Extended Spectrum Beta-lactamases and Carbapenem-Resistant Enterobacteriaceae with abatements up to 98% for E. coli and faecal coliform, 100% for Vibrio cholerae and 91.96% for total flora. Our results supported high capacity of Moringa Oleifera seeds as an excellent alternative for pathogens and antibiotics resistant bacteria reduction/purification from domestic wastewater

Water reuse for irrigation is increasingly recognized as an essential and economical strategy in areas with water scarcity. A simple, low-cost, low-maintenance, and highly efficient Pond-In-Pond (PIP) treatment system can be used for wastewater reuse. PIP is a treatment technology in which two types of ponds -- anaerobic and aerobic -- are combined into a single pond and consist of a deeper inner section entirely submerged within the outer pond. Previous studies on PIPs and PIP-like systems have reinforced the potential for reuse through promising performance results with BOD removal over 80% and a reduction in land area requirements by approximately 40%. Yet, no prior efforts have been made to understand the performance mechanism of such systems. This study makes use of two, 2-D modeling tools in developing a fundamental understanding of PIP flow dynamics and the expected performance. The modeling results showed that the PIP configuration offers improved flow diversion along with reduced flow velocity. Additionally, the PIP retained approximately 17% more (p<0.05) particles than the traditional pond with most of the particles concentrated within the inner pond. Lower velocity and the higher solids retention in the PIP thus allowed for better treatment performance compared to traditional ponds. The findings from this study can be used as preliminary data for future in-depth investigations of the PIP system leading toward effective and optimal designs. This will help address the major societal concern of water scarcity with low-cost and effective wastewater treatment.

In order to harmonize supply and demand of green energy, new future-proof technologies are needed. Here, hydrogen plays a key role. Within the current framework conditions, the production of green hydrogen is not yet economically viable. The use of the oxygen produced and the possible increase in efficiency associated with it mostly remains unconsidered. The aim is to demonstrate that the economic efficiency of a power-to-gas (PtG) project can be increased by using the by-product oxygen. In this research project, a water electrolyser connected to grid is powered to supply hydrogen to a hydrogen refuelling station. By utilising the by-product oxygen from water electrolysis for a wastewater treatment plant (WWTP), it is shown that the net present value (NPV) of the project can be improved by up to 13 % compared to the initial scenario. If a photovoltaic (PV) system is used in addition to grid electricity for higher green hydrogen production, the NPV can be further improved by up to 58 %. The levelized cost of hydrogen (LCOH) is calculated for different scenarios with and without oxygen configuration. A sensitivity analysis is then performed to find important parameters.

Water resources are under pressure because of human activities. Its management faces the challenge of enhancing long-term water security while minimizing undesirable economic, social, and environmental impacts along with its production chain. Since water and wastewater treatment plants are designed to maintain and conserve freshwater provisioning services, it is paramount to understand how it operates before proposing options for sustainability. At this point, the diagnosis phase claims for methods scientifically-based, systemic, and more objective to provide information for decision-makers towards strategic management of water resources. This work applies the five-sector sustainability model (5SenSu) to assess Brazil's twenty major water and wastewater treatment companies (WWTC) to quantify their sustainability levels that allow ranking procedures and the establishment of benchmarks for improvements. Under comparative basis, results identified the top-three sustainable companies, CORSAN, CASAN, and SANEPAR, which should be considered examples of best practices. Specifically, the following best-ranked companies in each sector within 5SenSu should be used as benchmark patterns for more oriented best practices: SANEAGO, sector 1; AGESISA, sector 2; CORSAN, sector 3; CASAL, sector 4; MA, sector 5. This work contributes to the advancement in modeling sustainability assessment of human-managed systems (applied in WWTCs in this present study) from a systemic and epistemologically rooted approach, avoiding shortcomings and misleading discussions on the sustainability issue. Quantifying sustainability of WWTCS from 5SenSu allows the identification of those sectors/indicators that requires immediate cleaner production practices by decision-makers to improve overall sustainability, besides identifying those companies more aligned with the requirements of UN SDGs.

Stresses due to drought and high soil salt content are the most severe threats to global rice pro-duction, causing a significant decline in rice yield. Therefore, this study examined the effects of treatment with various plant extracts on the stresses on rice plants associated with drought and high salinity. Additionally, this study examined various physiological and biochemical parameters such as growth, photosynthetic activity, chlorophyll content, and lipid peroxidation in rice plants after treatment with selected plant extracts under drought and salt stress conditions. Out of the eleven extracts tested, four extracts, namely soybean leaf, soybean stem, Chinese chive, and onion extracts, were found to effectively reduce drought stress. A reduction of only 24-37% in shoot fresh weight was observed in rice plants under drought stress that were treated with these ex-tracts compared to the 78% reduction observed in control plants. In addition, rice plants under salt stress which were treated with soybean leaf, soybean stem, moringa (Moringa oleifera), and Undaria pinnatifida extracts were observed to have lower reductions in shoot fresh weight (3-23%) com-pared to the control plants (43%). The effectiveness varied with the concentrations of the plant ex-tracts. Water content was higher in the rice plants treated with extracts than in the control plants after 6 days of drought and salt stress, but not after 4 days of drought and salt stress. Although photosynthetic efficiency (Fv/Fm) and electron transport rate (ETR), and the content of pigments (chlorophyll and carotenoid) varied based on the types and levels of stress and the extracts that the rice plants were treated with, generally photosynthetic efficiency and pigment contents were higher in the treated rice compared to control plants than in the control plants. Reactive oxygen species (ROS) such as the superoxide radical, hydrogen peroxide (H2O2), and malondialdehyde (MDA) levels increased as the duration of the period of stress increased. ROS and MDA levels were lower in the treated rice compared to control plants. Proline and soluble sugar accumulation also increased as the duration of the stressperiod increased. However, proline and soluble sugar ac-cumulation were lower in the treated rice compared to control plants. Generally, all the parame-ters investigated in this study were similar regardless of the plant extract used for treating the rice plants. Thus, extracts found to be effective in this study can be used to alleviate the adverse effects of stress on rice crops associated with drought and high salinity soil.

High hopes were associated with the new anti-angiogenic medicament, bevacizumab, which due to the possibility of binding to isoform A of vascular endothelial growth factor (VEGF), inhibited the creation of new blood vessels. However, not only blood vessels are responsible for the tumor cells' spread. During the process of tumor growth, lymphangiogenesis is mediated by other isoforms of the VEGF family, specifically VEGF-C and VEGF-D, which are independent of the bevacizumab action. Therefore, based on the mechanism of bevacizumab action and the processes of angio- and lymphangiogenesis, we formed three hypotheses: 1) if the lymph nodes in the primary ovarian cancers are metastatic, the outcome of bevacizumab treatment is worsened; 2) concerning the second-line treatment, bevacizumab will act in a weakened manner if the recurrence occurs in lymph nodes compared to local recurrences; 3) patients treated by bevacizumab are more likely to have recurrences in lymph nodes. These hypotheses raise the issue of the existing gap of knowledge, which concerns the effect of bevacizumab on the metastatic lymph nodes.

The development of computational acoustics allows simulation of sound generation and propagation in complex environment. In particular, meshfree methods are widely used to solve acoustics problems through arbitrarily distributed field points and approximation smoothness flexibility. As a Lagrangian meshfree method, smoothed particle hydrodynamics (SPH) method reduce the difficulty in solving problems with deformable boundaries, complex topologies, or multiphase medium. The traditional SPH method has been applied in acoustic simulation. This study presents the corrective smoothed particle method (CSPM), which is a combination of SPH kernel estimate and Taylor series expansion. The CSPM is introduced as a Lagrangian approach to improve accuracy in solving acoustic wave equations in the time domain. Moreover, a boundary treatment technique based on the hybrid meshfree and finite difference time domain (FDTD) method is proposed to represent different acoustic boundaries with particles. To model sound propagation in pipes with different boundaries, soft, rigid, and absorbing boundary conditions are built with this technique. Numerical results show that the CSPM algorithm is consistent and demonstrates convergence with exact solutions. Main computational parameters are discussed, and different boundary conditions are validated to be effective for benchmark problems in computational acoustics.

The chemical investigation of the anti-yeast methanol extract from the stem bark of Terminalia mantaly led to the isolation of seven compounds: 3-O-methyl-4-O-α-rhamnopyranoside ellagic acid (1), 3-O-mehylellagic acid (2), arjungenin or 2,3,19,23-tetrahydroxyolean-12-en-28-oïc acid (3), arjunglucoside or 2,3,19,23-tetrahydroxyolean-12-en-28-oïc acid glucopyranoside (4), 2α,3α,24-trihydroxyolean-11,13(18)-dien-28-oïc acid (5), stigmasterol (6), stigmasterol 3-O-β-D-glucopyranoside (7). Their structures were established by means of spectroscopic analysis and comparison with published data. Compounds 1-5 were tested in vitro for activity against three pathogenic yeast isolates, Candida albicans, Candida parapsilosis and Candida krusei. The activity of compounds 1, 2 and 4 were comparable to that of the reference compound fluconazole (MIC values below 32 µg/ml) against the three tested yeast isolates. They were also tested for inhibitory properties against four enzymes of metabolic significance: Glucose-6-Phosphate Deshydrogenase (G6PD), human erythrocyte Carbonic anhydrase I and II (hCA I and hCA II), Glutathione S-transferase (GST). Compound 4 showed highly potent inhibitory property against the four tested enzymes with overall IC₅₀ values below 4 µM and inhibitory constant (Ki) <3 µM.

Wastewater-based epidemiology (WBE) has emerged as a key method for continuous monitoring of COVID-19 prevalence including circulating SARS-CoV-2 lineages. WBE addresses limitations of traditional clinical COVID-19 surveillance such as clinical test availability, fluctuating testing rates and increased reliance on rapid antigen tests. Our study in Perth, Western Australia, found a significant positive correlation between SARS-CoV-2 concentrations in wastewater and clinical PCR positivity rates (rs = 0.772; p < 0.001) over an 18-month period that included four successive COVID-19 waves. A strong positive correlation was apparent between the proportions of SARS-CoV-2 lineages in wastewater and clinical cases within the same region (rs = 0.728; p < 0.001), including earlier detection of Omicron and recombinant lineages in wastewater before clinical case confirmation. The successful integration of WBE with healthcare data underscores its critical role in enhancing public health decision-making and pandemic management. This approach not only demonstrates the value of WBE in current global health surveillance efforts but also highlights the potential of WBE to address future public health challenges, as a comprehensive disease monitoring and response approach.

Pakistan flora is enriched with potent bioactive compounds that must be explored while Alzheimer's disease (AD) poses a global challenge driven by neurochemical imbalances. Acetylcholinesterase (AChE) inhibitors traditionally alleviate symptoms, but addressing the root cause remains elusive. This gap has led to the exploration of herbal sources for interventions. In this context, we analyzed fifty 50 medicinal plants for their phytochemical composition and antioxidant and acetylcholinesterase inhibition activities. AChE activity was measured using Ellman’s method. Santalum album exhibited significant AChE inhibition (86.2%), surpassing galantamine hydrobromide (81.8%). Promising inhibition was also seen in Bombax ceiba (77.8%), Acacia karoo (52.9%), and Phaseolus lunatus (50.1%). Detailed analysis revealed Santalum album's abundance in terpenoids, flavonoids, tannins, and phenolics, potentially correlating with its antioxidant and AChE inhibitory effects. Acacia karoo demonstrated elevated levels of total alkaloids, antioxidants, terpenoids, and tannins. Both Acacia karoo and Santalum album show promise for AD intervention due to their AChE inhibitory activities and unique phytochemical attributes, warranting further exploration, particularly for Acacia karoo's novel potential in AChE inhibition, to advance targeted AD therapeutics utilizing natural resources. This study contributes to the search for effective AD strategies from nature's pharmacological resources.

Recent advances in artificial intelligence combined with behavioral sciences have led to the development of cutting-edge tools for recognizing human emotions based on text, video, audio, and physiological data. However, these data sources are expensive, intrusive, and regulated, unlike plants which have been shown to be sensitive to human steps and sounds. A methodology is proposed to use plants as human emotion detectors. Electrical signals from plants are tracked and labeled based on video data. Labeled data are then used for classification. MLP, biLSTM, MFCC-CNN, MFCC-ResNet, and additionally, Random Forests, 1-Dimensional CNN, and biLSTM without windowing models are set using a grid search algorithm with cross-validation. Finally, best-parameterized models are trained and used with the test set for classification. The performance of this methodology is measured with a case study with 54 participants, who were watching an emotionally charged video, as ground truth their facial emotions were simultaneously measured using face emotion analysis. The Random Forest model shows the best performance, particularly in recognizing high-arousal emotions, achieving an overall weighted accuracy of 55.2% and demonstrating high weighted recall in emotions such as fear 61.0% and happiness 60.4%. The MFCC-ResNet model offers decently balanced results, with Accuracy(MFCC-ResNet)=0.318 and Recall (MFCC-ResNet)=0.324. With the MFCC-ResNet model fear and anger are recognized with 75% and 50% recall respectively. Thus, using plants as an emotion recognition tool seems worth investigating, addressing both cost and privacy concerns.

Aim: To evaluate the panmacular subthreshold micropulse laser treatment results among patients with central serous chorioretinopathy (CSC) and their correlation with functional and morphological parameters. Material and methods: The examined group included 10 non-treated and 41 treated patients with acute, recurrent, and chronic CSC (13 F, 38 M, mean age 44.11±6.5) and 14 healthy controls (6 F, 8 M, mean age 45±9.3). The BCVA examination, ophthalmoscopy, microp-erimetry, angio-OCT and OCT were performed. The medical history regarding chronic general disorders and known risk factors were recorded. Results: Complete resorption of SRF was obtained in 100% aCSC, 86.66% cCSC, and 63.63% r CSC. BCVA and RetSens significantly improved most of the patients treated in aCSC. The lowest BCVA and RetSens, but the largest pachyvessel and disease duration, were found in rCSC. A strong negative correlation between final BCVA and disease duration was found. No patient demonstrated laser lesions following treatment. Conclusions: The panmacular MPLT therapy leads to long-term enhancement of functional and morphological parameters in all CSC patients. The acute CSC patients showed the most significant improvement. The procedure is safe and could be considered a preferred treatment option for all active CSC cases. Timely treatment is crucial for beneficial outcomes.

Background: this interventional pilot study aimed to evaluate the short-term (3 years) efficacy of focal laser ablation (FLA) in treating the index lesion of low-intermediate risk prostate cancer, along with assessing the safety of the procedure (ClinicalTrials.gov ID NCT04045756). Methods: forty patients aged between 46 and 86 with histologically proven organ-confined prostate cancer and low to intermediate progression risk were included. FLA was performed under percutaneous fusion magnetic resonance/ultrasound guidance in a Day Hospital setting under local anesthesia. Patients underwent regular clinical assessments, PSA measurements, post-procedure MRI scans, and biopsies at 36 months or if positive findings were detected earlier. Statistical analyses were conducted to assess trends in PSA levels and cavity dimensions over time. Results: forty patients were initially included, with 15 lost to follow-up. At 36 months, a mean PSA reduction of 60% was observed, and 80% of MRI scans showed no signs of in-field clinically significant residual/recurrent cancer. Biopsies at 36 months revealed no malignant findings in 20 patients. No deterioration in sexual function or urinary symptoms was recorded. Conclusions: FLA appears to be safe, feasible and effective in the index lesion treatment of low-intermediate risk prostate cancer, with a high rate of tumor eradication and preservation of quality of life.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

The supply chain has incorporated products by putting them into hair scarfs. This study introduces the use of mini chips in health and beauty products and can reduce fatigue through enhanced sleep patterns. The mini chip could be placed in the scarf and used as a prototype. RFID technology provides the supply chain with specific information that is used to identify products and make communication easier. (Muhammad, et. al. 2013) This paper presents a new tool herein referred to as a scarf prototype which is developed to analyse EMG (electromyogram), ECG (electrocardiography), EEG (electroencephalogram), and EOG (electro-oculogram) signals that focuses in the area of sleep disorders. The mini chips used can be used to determine a solution for sleep disruption by using automated analytics. This could lead to improvement in our understanding of sleep disruption and overall sleep physiology. Automated technology allows repeated measurements, evaluation of sleep patterns, and provide suggestions to improve a person’s quality of sleep. This analysis compares the use of polysomnography and the scarf prototype. The analytics provide models and shows correlation between variables, such as EMG, ECG, EEG, and EOG. This study shows that the results from the scarf prototype is just as reliable as the original method, polysomnography.

Structural and functional asymmetries are traceable in every form of life and, at all cases, are a phenomenon of homology. Functionally speaking, the division of labour between the two halves of the brain is a basic characteristic of the nervous system that arose even before the appearance of vertebrates. The most prominent consequence of this specialization in humans and animals is handedness. Even if handedness is far more commonly associated with the presence of a nervous system, it is also observed in aneural organism such as plants. To date, little is known regarding the possible functional significance of handedness in plants, and many questions remain open (among these, whether it reflects a generalized behavioural asymmetry). Here, we propose a comparative perspective to the study of handedness, including plants, by taking advantage of the experimental models and paradigms already used to study laterality in humans and various animal species. By taking this approach, we aim to enrich our knowledge on the concept of handedness across natural kingdoms.

As the global demand for renewable energy continues to rise, biogas technology has emerged as a promising solution for sustainable energy generation. This review article presents the advantages of biogas technologies and extensively discusses the main principles of biogas production in the methane fermentation process. In this respect, the main parameters of the process, which require monitoring and are at the same time decisive for its course and efficiency are described, the principles of substrate selection are discussed and the necessity and advantages of the use of organic waste according to the model of a circular economy and the concept of sustainable development, are indicated. The part on biogas production is summarised with an explanation of the necessity to treat and purify biogas, taking into account the share of methane extracted. A special place in this paper is devoted to the design, construction, functioning and operation of biogas plants, based on both scientific and practical aspects. In conclusion of this chapter, the economic aspects and profitability of operating biogas plants are discussed, taking into account, in a theoretical balance sheet – in addition to investment and operating costs and the availability and cost of raw materials – the possibilities of producing and using electricity and heat, as well as environmental and social benefits. The article concludes with a discussion of opportunities and barriers to the development of biogas plants, pointing to: financial issues, access to feedstock, political regulations, public awareness and the geopolitical situation as key factors issues related to biogas plants – in different regions of the world.

This article presents an in-depth review of Virtual Power Plant (VPP), its organization in the energy system and its prospects in the face of the promising future of the increasing bidirectional complexity exposed in the current scenario. A new paradigm for the operations of modern power distribution and transmission systems requires greater grid flexibility that is accompanying an extensive change in the structure of electricity markets, the fruit of the development of the renewable industry and of the growing photovoltaic systems popularized, but in contrast due to the intermittent nature cause variable uncertainties in the power system. Innovative concepts like VPP are becoming a reality, establishing an efficient and effective mechanism. The objectives and components are described in a comprehensive way, and some of the most important are pointed out and presented in detail to contribute with a description of the energy systems and the implicit research needed for sustainability and resilience in the eminent energy scenario with this technology. In addition, the literature and studies of this technology already indicate a direction of this new tool as a promising solution to manage the uncertainties of the renewable energies.

The scratch test consists in pushing a tool across the surface of a material at a given penetration depth or applied load. It has several applications in Science and Engineering including strength testing, damage and quality control of thin films and coatings. Despite numerous attempts in scientific literature, the application of scratch test to characterizations of fracture properties remains a heavily controversial topic. Therefore, this investigation arises as an experimental study in order to assess the fracture toughness using scratch test. A study on the effect of cryogenic treatment, performed after tempering, on fracture toughness, via scratch test experiments, of different tool steels has been made. A laboratory investigation on AISI D2, AISI M2 and X105CrCoMo18 steel confirms the possibility of increasing the fracture toughness by carrying out the cryogenic treatment after the usual heat treatment

The Himalaya is well known for high diversity and ethnobotanical uses of medicinal plants. However, not all areas of the Himalayas are well studied. In particular, studies on ethnobotanical uses of plants from the Eastern Himalayas are rare and lacking for many tribes. Past studies primarily focused on listing plants name and their traditional medicinal uses. However, studies on traditional ethnopharmacological practices on medicine preparation had not yet been reported in published literature from the Eastern Himalaya. In this study, we are reporting the first time ethnopharmacological used 24 medicines, their procedures of preparation and listed 53 plant species used for those medicines for Monpa tribe. Such documentations had not yet been done for other tribes in India. Our research demonstrates the urgent need to documents traditional medicine preparation procedures from the local healers before rapid cultural modernization forgets them in transforming country like India. This study should motivate national and international researchers to do more works on ethnopharmacology and bioprospecting.

Coronavirus Disease-19 (COVID-19) is presently wreaking havoc on public health and socio-economic development. Besides the upper and lower respiratory tract involvement, gastrointestinal symptoms are also reported in COVID-19 patients through gut-lung axis. Finding its way through the feces of infected individuals and other sources, the genetic material of SARS-CoV-2 (ssRNA) is reported widely in wastewater and is being used as a fingerprint for its detection. With millions of cases arriving every day, there is a need to level up the testing speed efficiency. Due to the restricted sampling potential of testing laboratories, clinical testing is unable to track all the symptomatic and asymptomatic cases. Wastewater-based epidemiology (WBE) bestows an auxiliary monitoring tool that will contribute in community level screening. Sample collection, concentration, RNA extraction, quantification and data analysis are the main steps involved in implementation of WBE that can be relied upon as an alarm call for an upcoming wave, emergence of a new variant or any future pandemic. WBE can be a cheaper and more practical alternative to high end and sophisticated clinical testing for community transmission detection. Worldwide, there are more than 300 reports entailing the occurrence of SARS-CoV-2 in wastewater exhibiting unique temporal trends with five of them in India. This review aims to address the present knowledge on surveillance of SARS-CoV-2 in wastewater and its implications.

Microbial Fuel Cells (MFCs) representing a promising technology for the extract of energy and resources through wastewater and it also offer an economic solution to the problem of environment effluent and energy crisis in near future. The advance device is rather appealing, due its potential benefits, its practical application is, however hindered by several drawbacks, such an internally competing microbial reaction, and low power generation. This report is an endeavor to address various design connected to the MFCs application to wastewater treatment, in particular cost effective bioelectricity from waste water are reviewed and discussed with a multidisciplinary approach. The conclusions drawn herein can be of practical interest to all new researchers dealing with effluent wastewater treatment using MFCs.

This communication explores the transition from Cognitive Behavioural Therapy (CBT) to a more holistic model, named Complex Therapy, developed by Tullio Scrimali for explaining and treating mental disorders. The Author delves into the limitations of traditional CBT and introduces an innovative framework that integrates multiple therapeutic modalities. While CBT is based on the study and modification of behaviour and cognition, Complex Therapy includes, in its focus, the theory of human relationships, the attachment theory, neuroscience, applied neuroscience, complex systems theory and ecology.Complex Therapy addresses the multifaceted nature of mental health issues by combining evidence-based techniques with personalized care strategies. The goal is to enhance patient outcomes through a tailored, comprehensive treatment plan that adapts to the evolving needs of individuals facing mental health challenges.Two innovative and original items which Scrimali has developed, which are a device for Applied Neuroscience MindLAB Set and a new botanical drug, NegEnt, are presented and discussed.The topic also describes, an original and integrated protocol, named Negative Entropy, the author has developed for treating a challenging disorder, such as schizophrenia, he renamed Entropy of Mind.

Addressing non-unions involves stabilizing the affected area through osteosynthesis and improving bone biology using bone grafts. However, there is no consensus on the optimal treatment method. This study aims to compare outcomes of non-union revision using conventional treatment methods (metal hardware ± graft) versus osteosynthesis with the human, allogeneic cortical bone screw (Shark Screw®). Thirty-four patients underwent conventional treatment, while 28 cases received Shark Screws®. Patient demographics, bone healing, time to bone healing, and complications were assessed. Results revealed a healing rate of 96.4% for the Shark Screw® group, compared to 82.3% for the conventionally treated group. The Shark Screw® group exhibited a tendency for faster bone healing (9.4±3.2 vs. 12.9±8.5 weeks, p=0.05061). Hardware irritations led to six metal removals in the conventional group versus two in the Shark Screw® group. The Shark Screw® emerges as a promising option for personalized non-union treatment in the foot, ankle, and select lower leg cases, facilitating effective osteosynthesis and grafting within a single construct, promoting high union rates, low complications, and a rapid healing process.

Background/Objectives: Vitamin B12 deficiency can cause variable symptoms, which may be irreversible if not diagnosed and treated in a timely manner. We aimed to develop a widely accepted expert consensus to guide the practice of diagnosing and treating B12 deficiency. Methods: We conducted a scoping review of the literature published in PubMed since January 2003. Data were used to design a two-round Delphi survey to study the level of consensus among 42 experts. Results: The panelists agreed on the need for educational and organizational changes in the current medical practices for diagnosing and treating B12 deficiency. Recognition of clinical symptoms should receive the highest priority in establishing the diagnosis. There is agreement that the serum B12 concentration is useful as a screening marker, whereas methylmalonic acid or homocysteine can support the diagnosis. Patient lifestyle, disease history and medications can provide clues to the cause of B12 deficiency. Regardless of the cause of the deficiency, initial treatment with parenteral B12 was regarded as the first choice for patients with acute and severe manifestations of B12 deficiency. The use of high-dose oral B12 at different frequencies may be considered for long-term treatment. Prophylactic B12 supplementation should be considered for specific high-risk groups. Conclusions: There is a consensus that clinical symptoms need to receive more attention in establishing a diagnosis. B12 laboratory markers can support the diagnosis. The severity of clinical symptoms, the causes of B12 deficiency and the treatment goals govern decisions regarding the route and dose of B12 therapy.

The current treatment for cervico-facial cancer involves radio and/or chemotherapy. Unfortunately, cancer therapies can lead to local and systemic complications such as mucositis, which is the most common dose-dependent complication in the oral cavity and gastrointestinal tract. Mucositis can cause a considerably reduced quality of life in cancer patients already suffering from physical and psychological exhaustion. However, melatonin, whose role in the treatment of mucositis has recently been investigated, offers an effective alternative therapy in the prevention and/or management of radio and/or chemotherapy-induced mucositis. This review focuses on the pathobiology and management of mucositis in order to improve the quality of cancer patients’ lives.

Fouling by activated sludge in membrane bioreactor (MBR) processes for wastewater treatment can be reduced using several strategies such as backflushing, relaxation, and chemical cleaning. Some proprietary systems such as Avanti’s RPU-185 Flexidisks MBR use novel circular rotating, flat sheet membranes to assist in limiting this fouling. An attempt has already been made to model this novel rotating fouling process by developing a simulation model based on first principles and traditional fouling mechanisms. In order to directly compare the potential benefits of rotational MBR system, a follow-up study was carried out using Avanti’s newly developed static (non-rotating) Flexidisks MBR system. This new process uses the same proprietary and patented membrane modular arrangement as used in the circular rotational unit, but is configured instead as a static square-shaped unit which is in-line with the more traditional and popular format used for submerged flat sheet MBR systems. During this study, the results from operating the static pilot unit were simulated and modelled using a standard fouling model coupled with a viscosity to mixed liquor relationship model. These results were then compared with those obtained from running the rotating MBR model however with rotational switching functions turned off and rotational parameters set to a static mode. This comparison was done to ascertain whether the basic premise of the developed rotational model was sound in empirical terms when compared to a standard MBR flux model. The study concluded that relatively good agreement was reached between the two types of models, thus vindicating the usage of a complex rotational MBR model. Follow on studies will now compare results from the rotating MBR system using rotational models developed by other researchers to ascertain the effectiveness rotating MBR modelling approach.

Enteric infections are a major public health concern. Detecting risk areas requires a strong surveillance system for pathogenic viruses in possible sources such as wastewater. To build an environmental surveillance system, we aimed to identify group A rotavirus (RVA) and human adenovirus (HAdV) in wastewater. We also focused on three different methods of viral concentration to determine suitability for a regular surveillance system. We screened 20 wastewater samples for HAdV and RVA using quantitative polymerase chain reaction (qPCR) and conventional polymerase chain reaction (cPCR). Sixteen posi-tives (18/20) and ten (14/20) positives for HAdV and RVA, respectively, were obtained on qPCR, representing a prevalence of 90% and 70%. Twelve (12) positives were successfully amplified. Bag-mediated filtration system (BMFS) and skimmed milk (SM) flocculation were the most consistent viral concentration methods for HAdV and RVA, respectively. Human adenovirus was identified with nucleotide identity range of 98.48% to 99.53%. Statistical analysis of positives showed that viral burden differed by site (P

Wastewater surveillance for SARS-CoV-2 has garnered extensive public attention during the COVID-19 pandemic as a proposed complement to existing disease surveillance systems. Over the past year, methods for detection and quantification of SARS-CoV-2 viral RNA in untreated sewage have advanced, and concentrations in wastewater have been shown to correlate with trends in reported cases. Despite the promise of wastewater surveillance, for these measurements to translate into useful public health tools, it is necessary to bridge the communication and knowledge gaps between researchers and public health responders. Here we describe the key uses, barriers, and applicability of SARS-CoV-2 wastewater surveillance for supporting public health decisions and actions, including establishing ethical consideration for monitoring. Overall, while wastewater surveillance to assess community infections is not a new idea, by addressing these barriers, the COVID-19 pandemic may be the initiating event that turns this emerging public health tool into a sustainable nationwide surveillance system.

Metabolomics is now considered to be a wide-ranging, sensitive and practical approach to acquire useful information on the composition of a metabolite pool present in any organism, including plants. Investigating metabolomic regulation in plants is essential to understand their adaptation, acclimation and defense response to environmental stresses through the production of numerous metabolites. Moreover, metabolomics can be easily applied for the phenotyping of plants; and thus, it has great potential to be used in molecular breeding and genome editing programs to develop superior next generation crops. This review describes the recent analytical tools and techniques available to study plants metabolome, along with their significance of sample preparation using targeted and non-targeted method. Advanced analytical tools, like gas chromatography-mass spectrometry (GC-MS), liquid chromatography mass-spectroscopy (LC-MS), capillary electrophoresis-mass spectrometry (CE-MS), fourier transform ion cyclotron resonance-mass spectrometry (FTICR-MS) and matrix-assisted laser desorption/ionization (MALDI) have speed up metabolic profiling in plants. Further, we deliver a complete overview of bioinformatics tools and plant metabolome database that can be utilized to advance our knowledge to plant biology.

The antioxidant properties and polyphenol content of some selected aromatic plants grown in Greece were studied. Plants were refluxed with 60% methanol after acid hydrolysis. The phenolic substances were quantified by HPLC-DAD. The antioxidant capacity of the extracts was determined with the Rancimat test using sunflower oil as substrate. Free radical scavenging activity was measured using the stable free radical 1, 1-diphenyl-2-picrylhydrazyl (DPPH). Results were compared with standard BHT and ascorbic acid. Total phenol concentration of the extracts was estimated with Folin-Ciocalteu reagent using gallic acid as standard.

Obsessive–compulsive disorder (OCD) is believed to follow a waxing and waning course, often according to environmental stressors. During the COVID-19 pandemic, pre-existing OCD symptoms were reported to increase and to change from checking to washing behaviors, while new-onset symptoms were predominantly of the hoarding type. In the present study, we followed the evolution of OCD symptoms, anxiety, depression, and insight of illness in forty-six OCD patients throughout the pandemic. Clinical measures were collected at four different time points before and during the COVID-19 pandemic in Italy. Within-subject comparisons were used to compare clinical scale scores across time, and correlations were examined between patients' baseline characteristics and changes in clinical scores. We found that all clinical measures increased during the first Italian lockdown, with respect to the pre-pandemic values. Anxiety decreased during the temporary elimination of restriction provisions, whereas severity of OCD symptoms and insight returned to pre-pandemic values during the second mandatory lockdown. These results were observed only in two sub-groups of patients: those taking benzodiazepines and those with shorter illness duration. Our findings suggest the need of additional clinical attention to these specific sub-groups of OCD patients in case of particularly distressing circumstances, while pointing to a possible adaptive role of their OCD symptoms when the environment requires a higher care of hygiene and extraordinary supply of essential resources.