The objective of this research is to develop an experimental-theoretical analysis about the influence of the cooling medium and the geometry of the welding bead profile in fatigue life and associated parameters with structural integrity of welded joints. A welded joint with cruciform geometry is considered using SMAW, plates in structural steel ASTM A36 HR of 8 mm of thickness and E6013 electrode input. A three-dimensional computational model of the cruciform joint was created using the finite element method. For this model, the surface undulation of the cord and differentiation in the mechanical properties of the fusion zone were considered, the heat-affected zone (HAZ) and base material, respectively. In addition, an initial residual stress field which was established experimentally was considered. The results were a set of analytical expressions for the weld magnification factor Mk. It was found that values for the latter decrease markedly in function of the intensity of the cooling medium used in the post welding cooling phase, mainly due to the effect of the residual compressive stresses. The obtained models of behavior of the weld magnification factor are compared with the results from other researchers with some small differences, mainly due to the inclusion of the cooling effect of the post weld and the variation of the leg of the weld bead. The obtained analytical equations in the present research for Mk can be used in management models of life and structural integrity for this type of welded joint.

Building defects are very prevalent and contribute significantly to a building's economic value. There are numerous information sources on building defects that have a lot potential for learning more about building defects. This study aimed to identify the information sources used in previous building defect studies and to identify the motivation for carrying out such studies. To fulfil this aim a scoping study was carried out. The information sources identified included insurance companies, private databases, questionnaire surveys, lawsuits, building surveys, client complaint forms, and maintenance reports. This study found that insurance company and client complaint forms include the largest collection of real building defect cases, but such databases may lack detailed descriptions of the causes of the defects. The main purposes of building defects studies identified here included design challenges, identification of defects, building maintenance management, quality management, systematization in data collection, providing an overview of typical defects, and classifying defects. Identification was found to be the most common purpose, indicating that the industry wants to learn more. This study identified research gaps in the climate perspective in relation to building defects. Most of the studies focused on the economical perspective, and none focused on the carbon footprint perspective.

Dissimilar welds between ferritic and austenitic steels represent a good solution for exploiting the best performance of stainless steels at high and low temperatures and in aggressive environments, while minimizing costs. Therefore, they are widely used in nuclear and petrochemical plants, however, due to the different properties of the steels involved, the welding process can be challenging. Fusion welding can be specifically addressed to connect low-carbon, or low-alloy steels, with high-alloy steels, which have similar melting point. Welding of thick plates can be performed with electric arc in multiple passes or in a single pass by means of a laser beam equipment. Since microstructure and consequently mechanical properties of the weld are closely related to composition, the choice of the filler metal and processing parameters, which in turn affects the dilution rate, plays a fundamental role. Numerous technical solutions were proposed for welding dissimilar steels and much research was developed on the weldment metallurgy; therefore, this article is aimed at a review of the most recent scientific literature on the issues relating to the fusion welding of ferritic / austenitic steels. Two specific sections are dedicated respectively to electric arc and laser beam welding; finally, metallurgical issues, related to dilution and thermal field are debated in the discussion section.

Hypertension is a global public health challenge, with a high prevalence across various regions and significant implications for cardiovascular risk. This article reviews the effectiveness of herbal medicine as a potential therapeutic approach for hypertension, offering an alternative or complementary solution to conventional pharmacological treatments. It highlights several natural agents that have demonstrated efficacy in lowering systolic blood pressure (SBP) in clinical and meta-analytical studies. The methodology involved a systematic review of articles that discuss herbal therapeutics for hypertension, focusing on their efficacy compared to placebo and standard treatments. The findings suggest that certain nutraceuticals, such as garlic, hawthorn, and CoQ10, can significantly reduce SBP, presenting a viable option for managing hypertension. This review underscores the need for further research to validate these findings and optimize herbal treatment strategies, potentially expanding the use of these natural products in clinical practice. The article aims to increase awareness among medical professionals and patients about the benefits and applications of herbal medicines in treating hypertension.

Reducing and time-shifting household energy demand is important for a sustainable transition of energy systems, and dynamic electricity pricing, like real-time pricing (RTP), is a popular instrument to incite households to change energy demand. However, the effect of such products relies on the assumption that dynamic price signals incorporate into everyday routines and rhythms. This paper investigates the flexibility of households’ everyday routines and rhythms. The study provides three insights based on 11 Danish household visits and interviews with electricity customers who are new to RTP. First, the interviews indicated confusion over terminology for dynamic pricing products and low interest in flexible energy demand. Second, everyday practices (already) appeared flexible but for other reasons than energy demand flexibility. Third, energy habits were important for providing meaning to everyday practices. In addition, the study shows that energy flexibility is not just about energy demand, but rather about all the other activities that form routines and rhythms in everyday life. We suggest 1) designing products that reflect ‘natural’ or ‘societal’ daily rhythms, 2) focusing on the engaged households, and 3) being aware that for some households, changes in pricing, including new payment schemes, might put extra pressure on already harried everyday routines.

Steel structures, such as bridges, must be continuously maintained. Due to increasing trac loads, design and execution shortcomings, many steel bridges are subject to various types of damage, such as cracks. The bridges must be maintained by crack removal and re-welding the cracks. During this work, the bridge is closed for trac in order to suppress the crack ank movement during welding. As a result, trac loads on other routes are higher, which increases further damage on detour routes and subsequently additional welding work and costs on theses structures. Therefore, the aim is to provide a method that allows welding work on steel structures under running trac, respectively under cyclic loads. First, measurements at a representative steel bridge were conducted to derive gap opening parameters of amplitude and frequency for welding tests under cyclic loads. In a test setup for reproducible and comparable welding tests, specimen were welded under cyclic loads. Deep grinding of the root layer allowed defect-free welding within the range of 0.1 mm amplitude at a frequency of 2 Hz loadings. For such welds, the weld quality and the fatigue strength was comparable to the standard requirements.

Context. During the COVID-19 pandemic, patient care was mainly organised around the hospital. Pre-hospital care has, to our knowledge, never been evaluated. Objective: To evaluate the impact of pre-hospital pathways on hospitalisation during the last part of the pandemic. Design. This was a monocentric retrospective analysis of prospectively collected medical records. Data from patients admitted to our institute between 1 February and 7 March 2022 were analysed. Main Outcome Measure(s): The primary outcomes were defined as the number of hospitalisations, resuscitations, and deaths at the time of interview and in the subsequent 30 days. The main explanatory variables were times from onset of symptoms to care, age, gender, News2 score, comorbidities, and pre-hospital pathways and their duration. Results: Three pre-hospital pathways have been identified: a pathway in which the patient consults a general practitioner for a test (PHP1); a pathway in which the patient consulted for care (PHP2); and no pre-hospital pathway and direct admission to hospital (PHP3). Factors independently associated with outcome (hospitalisation) were being male (OR 95% CI; 2.21 [1.01–4.84], p=0,04), News2 score (OR 95% CI; 2.04 [1.65–2.51], p<0.001), obesity (OR 95% CI; 3.45 [1.48–8.09], p=0.005), D-dimers > 0.5 µg/ml (OR 95% CI; 3.45 [1.47–8.12], p=0.005), prolonged time from symptoms to hospital care (PHP duration) (OR 95% CI; 1.07 [1.01–1.14], p=0.03). All things being equal, patients with a “PHP2” pre-hospital pathway had a higher probability of hospitalisation compared to those with a “PHP3” pre-hospital pathway (OR 95% CI; 4.31 [1.48–12.55], p=0.007). Conclusions. Along with recognised risk factors such as gender, News 2 score, and obesity, the patient’s pre-hospital pathway is an important risk factor associated with hospitalisation.

High hepcidin is linked to low-grade inflammation and lower iron levels. The consequence of testosterone replacement therapy (TRT) on inflammation and risk of cardiovascular disease (CVD) is undetermined. We investigate the effect of TRT on the inflammatory cardiovascular risk markers hepcidin-iron, fibroblast growth factor 23 (FGF23)-phosphate-klotho, and calprotectin pathways. Methods: A randomized, placebo-controlled, double-blinded study at an academic tertiary-care medical center. Interventions were testosterone gel (TRT, n=20) or placebo gel (n=19) for 24 weeks. We included 39 men (50─70 years) with type 2 diabetes (T2D) on metformin monotherapy with bioavailable testosterone levels <7.3 nmol/L. Body composition was assessed by DXA- and MRI-scans; main study outcomes were serum hepcidin-iron, FGF23, phosphate, klotho, and calprotectin. Results: Hepcidin levels decreased during TRT (β=-9.5 ng/mL, P<0.001), lean body mass (β=1.9 kg, P=0.001) increased, and total fat mass (β=-1.3 kg, P=0.009) decreased compared to placebo. Delta hepcidin was not associated with changes in lean body mass or fat mass. Iron and the pathways of FGF23-phosphate-klotho and calprotectin were unchanged during TRT. Conclusions: During TRT, the reduction in hepcidin was not associated with circulating iron levels, lean body mass, or fat mass; these findings suggested a direct anti-inflammatory effect of TRT and no indirect effect mediated through these factors.

ASTM A743 CA6NM alloy is a martensitic stainless steel typically used in energy industry -runners and hydraulic turbine components- due to its superior toughness, yield and fatigue properties. In both the manufacturing, shielded metal arc welding is applied to join for this grade steels. However, weldability of the steels is limited due to formation of hard and brittle phases such as untempered martensite during welding and post weld heat treatment processes. The formation causes a reduction in toughness. In this study, influence of post-weld heat treatment procedure (single tempering and double tempering) and parameters on microstructure and hardness of AWS410NiMo all weld metal. Hardness tests were conducted from weld metal. Microstructures of the all weld metals subjected to different heat treatment process were characterized.

Enhancing spectral efficiency, especially in Non-line-of-Sight environments, is emerging as a pivotal necessity when dealing with the evolving landscape of 5G networks and beyond, sur-passing the capabilities of previous 4G systems to achieve a high information rate combined with minimal interference. Contrary to depending on the traditional Orthogonal Multiple Access (OMA) systems to tackle the issues caused by Non-line-of-Sight (NLoS) environments, advanced wireless networks are focusing on adopting innovative models such as Non-Orthogonal Multiple Access (NOMA), MIMO, IRS technology, etc. In this paper, we present technologies that can be integrated with NOMA to enhance communication reliability in environments that suffer from issues such as limited coverage and lower spectral efficiency mainly caused by huge obstacles. Our exploration includes the fundamental concepts of Cooperative NOMA (C-NOMA), Multiple Input Multiple Output (MIMO), Intelligent Reflective Surfaces (IRS), Unmanned Aerial Vehicles (UAVs), and Energy Harvesting (HV), which adds a layer of sophistication, promising not only improved connectivity but also contributing to a more reliable and environmentally friendly data trans-mission landscape.

The systematic sampling is used as a method to get the quantitative results from the tissues and the radiological images. Systematic sampling on real line (R) is a very attractive method within which the biomedical imaging is consulted by the practitioners. For the systematic sampling on R, the measurement function (MF) is occurred by slicing the three-dimensional object equidistant systematically. The currently used covariogram model in variance approximation proposed by [28,29] is tested for the different measurement functions in a class to see the performance on the variance estimation of systematically sampled R. This study is an extension of [17], and an exact calculation method is proposed to calculate the constant λ(q,N) of confidence interval in the systematic sampling. The exact value of constant λ(q,N) is examined for the different measurement functions as well. As a result, it is observed from the simulation that the proposed MF should be used to check the performances of the variance approximation and the constant λ(q,N). Synthetic data can support the results of real data.

Spontaneous tumours in higher plants can develop depending on plant genotype without any pathogen invasion. Spontaneous tumour formation on the taproots is consistently observed in certain inbred lines of radish (Raphanus sativus var. radicula Pers.). In this work, we have sequenced the genomes of two closely related radish inbred lines that differ in their ability to spontaneously form tumours. We have identified numerous single nucleotide variants (amino acid substitutions, insertions or deletions) that are likely to be associated with the spontaneous tumour formation. Furthermore, we performed the identification of CLE and WOX genes the genomic sequences of the radish inbred lines and, as a result, identified two unique radish CLE genes which probably encode proteins with multiple CLE domains. The results obtained provide a basis for investigating the mechanisms of plant tumour formation and also for future genetic and genomic studies of radish.

Elizabethkingia anophelis is an opportunistic pathogen causing lifethreatening infections in humans, particularly in immunocompromised patients, neonates and elderly. Infections caused by this species are exceptionally challenging to treat due to its multiresistance to antimicrobials. We report a case of central line-associated bloodstream infection by E. anophelis in a 2.5-year-old girl with acute lymphoblastic leukemia successfully treated with a combination of piperacillin/tazobactam and amikacin. The literature was also reviewed on paediatric infections caused by E. anophelis. Accurate identification with MALDI-TOF, or using molecular techniques, is crucial because of varying susceptibilities among species. Early, accurate diagnosis and prompt effective treatment optimize outcomes.

This article presents a buck converter in which the inductor has been replaced by a transmission line. This approach would be practically conceivable if the power supply and load have a greater spatial distance. In the time domain, this new converter can be described by a system of coupled partial and ordinary differential equations. In the frequency domain, a transcendental transfer function is obtained. For comparison with an equivalently parameterized conventional converter, Padé approximants are derived. A linear controller is designed for the converter topology under consideration.

Recent advancements in semiconductor photonic and electronic devices such as Uni-travelling-carrier photodiodes (UTC-PDs), have played a significant role in the development of Terahertz communication technology. However, a major challenge that still persists is the limited output power from a single UTC-PD required for practical transmission distances. To enhance the output power, we propose and demonstrate a novel Terahertz wave power combining technique using a photomixer device that comprises of two arrayed UTC-PDs monolithically integrated with a microstrip line-based 2 × 1 Wilkinson power combiner and a rectangular patch antenna on a Silicon Carbide (SiC) substrate at 300 GHz. At photocurrents of 8 mA and 10 mA from the two UTC-PDs, the device experimentally exhibited a 7.3 dB increase in power relative to the power obtained with 8 mA UTC-PD and a 4.4 dB increase in power relative to the power obtained with 10 mA UTC-PD, when both UTC-PDs were irradiated. This implies that power can be enhanced by a factor of N2 if the photocurrent is multiplied by a factor of N. This technology presents a holistic and cutting edge platform for further power multiplication by further increasing the number of arrayed UTC-PDs.

Previous control methods developed by our research team cannot satisfy the high-accuracy requirements of unmanned surface vessel (USV) path-tracking during bathymetric mapping because of the excessive overshoot and slow convergence speed. For this reason, this study developed an adaptive fuzzy integral-derivative line-of-sight (AFIDLOS) guidance law for USV path-tracking control. Integral and derivative terms were added to counteract the effect of the sideslip angle, with which the USV could be quickly guided to converge to the planned path for bathymetric mapping. To obtain a high-accuracy of the look-ahead distance, a fuzzy control method was proposed. The proposed method was verified using simulations and outdoor experiments. The results demonstrate that the AFIDLOS guidance law can reduce the overshoot by 79.85%, shorten the settling time by 55.32% in simulation experiments, and reduce the average cross-track error by 10.91%, and can ensure a 30% overlap of neighboring strips of bathymetric LiDAR outdoor mapping when compared with the traditional method.

The effect of rare earth Pr6O11 on the microstructure and mechanical properties of high-strength steel weld metal was investigated by optical microscopy, scanning electron microscopy and mechanical testing. Three different contents of Pr6O11 were added to the flux-cored wires. The results showed that the addition of 1% Pr6O11 can promote the refinement and spheroidization of inclusions, refine the grains, form acicular ferrites, and significantly improve the toughness of weld metal. The addition of Pr6O11 promoted the formation of rare earth composite inclusions and acicular ferrites in the weld metal, refined the lath microstructure, inhibited the formation of martensite and bainite. The crack formation mode changed from the boundary cracking of the bainite clusters caused by the surface shear stress to the surface shear stress-induced decohesion of inclusion. However, excessive addition of Pr6O11 will reduce the number of inclusion nucleation and deteriorate the mechanical properties. The wire No.2 with 1% Pr6O11 had the good comprehensive mechanical properties, and the corresponding values were 835MPa of tensile strength and 72 J of impact toughness. These findings suggest that the control of Pr6O11 can be an effective way to improve the impact toughness of weld metal.

The effect of Pr6O11 on the microstructure and mechanical properties of high-strength steel weld metal was investigated by optical microscopy, scanning electron microscopy and mechanical testing. Three different contents of Pr6O11 were added to the flux-cored wires. The results demonstrate that the addition of 1% Pr6O11 can promote the refinement and spheroidization of inclusions, refine the grains, form acicular ferrites in the weld metal, and significantly improve the toughness. The addition of Pr6O11 promoted the formation of rare earth composite inclusions and acicular ferrites in the weld metal, refined the lath microstructure, inhibited the formation of martensite and bainite. The crack formation mode changed from the boundary cracking of the bainite clusters caused by the surface shear stress to the surface shear stress-induced decohesion of inclusion. Excessive addition of Pr6O11 will reduce the number of inclusion nucleation and deteriorate the mechanical properties. The wire No.2 with 1% Pr6O11 had the good comprehensive mechanical properties.

For multi-sensor integrated systems, such as a mobile mapping system (MMS), data fusion at sensor-level, i.e., the 2D-3D registration between optical camera and LiDAR, is a prerequisite for higher level fusion and further applications. This paper proposes a line-based registration method for panoramic images and LiDAR point cloud collected by a MMS. We first introduce the system configuration and specification, including the coordinate systems of the MMS, the 3D LiDAR scanners, and the two panoramic camera models. We then establish the line-based transformation model for panoramic camera. Finally, the proposed registration method is evaluated for two types of camera models by visual inspection and quantitative comparison. The results demonstrate that the line-based registration method can significantly improve the alignment of the panoramic image and LiDAR datasets under either the ideal spherical or the rigorous panoramic camera model, though the latter is more reliable.

This investigation aims to discuss the formation process of eddies and the heat transportation in plasma keyhole arc welding. In order to clarify this issue, the measurement of the convection inside the weld pool, the convection on the weld pool surface, also the temperature distribution on the weld pool surface were carried out. The results showed that two eddies were found in the weld pool, which is controlled mainly through the shear force by the plasma flow acting on the weld pool surface. The magnitude, extent and direction of the shear force are thought to be determined primarily by the variation of keyhole profile. The relative shape and strength of each eddy is largely changed depending on the change of the keyhole profile when nozzle diameter changed. These relative strengths of each eddy are considered to decisively govern the heat transport in the weld pool coinciding with the direction of eddies. A larger eddy near the lower part of the keyhole inside the weld pool was found out in the case of 1.6 mm, meanwhile a upward larger eddy was found out near the upper part of the keyhole inside the weld pool in the case of 2.4 mm.

Metal-catalyzed lipid oxidation is a major factor in food waste, as it reduces shelf life. Addressing this issue, our study investigates the potential of hydrolysates derived from potato protein, a by-product of potato starch production, as metal chelating antioxidants. Through sequential enzymatic hydrolysis using Alcalase or Trypsin combined with Flavourzyme, we produced various hydrolysates, which were then fractionated via ultrafiltration. Using a combination of peptidomics and bioinformatics, we predicted the presence of metal-chelating and free radical scavenging peptides across all hydrolysate fractions, with a trend indicating a higher content of antioxidant peptides in lower molecular weight fractions. To validate these predictions, we utilized Surface Plasmon Resonance (SPR) and a 9-day emulsion storage experiment. While SPR demonstrated potential in identifying antioxidant activity, it faced challenges in differentiating between hydrolysate fractions due to significant standard errors. In the storage experiment, all hydrolysates showed lipid oxidation inhibition, though not as effectively as EDTA. Remarkably, one fraction (AF13) was not significantly different (p < 0.05) from EDTA in suppressing hexanal formation. These results highlight SPR and peptidomics/bioinformatics as promising yet limited methods for antioxidant screening. Importantly, this study reveals the potential of potato protein hydrolysates as antioxidants in food products, warranting further research.

Based on the need for real-time sag monitoring of Overhead Power Lines (OPL) for electricity transmission, this article presents the implementation of a hardware and software system for online monitoring of OPL cables and cable sag determination. The mathematical model based on differential equations and the methods of algorithmic calculation of OPL cable sag are presented. Considering that, based on the mathematical model presented, the calculation of OPL cable sag can be done in different ways depending on the sensors used, and the presented application uses a variety of sensors. Therefore, a direct calculation is made using one of the different methods. Subsequently, the verification relations are highlighted directly and, respectively, the calculation by the alternative method, which uses another group of sensors, to generate both a verification of the calculation and the functionality of the sensors, thus obtaining a defect observer of the sensors. The hardware architecture of the OPL cable online monitoring application is presented, together with the main characteristics of the sensors and communication equipment used. The configurations required to transmit data using the ModBUS and ZigBee protocols are also presented. The main software modules of the OPL cable condition monitoring application are described, which ensure the monitoring of the main parameters of the power line and the visualisation of the results both on the electricity provider's intranet using a web server and MySQL database, and on the Internet using an Internet of Things (IoT) server. This categorisation of the data visualisation mode is done in such a way as to ensure a high level of cyber security. Starting from the mathematical model of the OPL cable sag calculation, it goes through the stages of creating such a monitoring system, from the numerical simulations carried out using Matlab to the real-time implementation of this monitoring application. The main modules of the application software are: the software module for reading quantities from the sensor network through a ModBUS Input/Output (I/O) server, the software module for real-time calculation of the OPL cable sag, the software module for read/write operations based on MySQL type data, the software module for transferring data to the user's intranet through a web server, and the software module for viewing data by authorised users based on user and password through an IoT server. The development software environments used are Matlab and Laboratory Virtual Instrument Engineering Workbench (LabVIEW).

This paper proposes a definition of fractional line integral, generalising the concept of fractional definite integral. The proposal replicates the properties of the classic definite integral, namely the fundamental theorem of integral calculus. It is based on the concept of fractional anti-derivative used to generalise the Barrow formula. To define the fractional line integrals the Gr\"unwald-Letnikov and Liouville directional derivatives are introduced and their properties described. The integral is defined first for broken line paths and afterwards to any regular curve

An effective method to inspect inaccessible nuclear power facility by interface wave which propagate along the shrink fit boundary of reactor head is proposed in this study. Reactor head is relatively thick to inspect from the outside of reactor by conventional ultrasonic testing. The proposed interface wave can propagate a long distance from the fixed transducer position. The inside of nuclear reactor is limited to access due to the high radiation, so transducers are located at outside of nuclear facility and interface wave propagates into the nuclear reactor for defect detection. The numerical simulation and experiments were carried out to validate the effectiveness of the proposed interface wave inspection method. Various defect cases simulating field failures are also presented with satisfactory detectability by the proposed technique with the features for defect classification.

The paper presents the possibility of using KINECT v2 module to control an industrial robot by means of gestures and voice commands. It describes elements of creating software for off-line and on-line robot control. The application for KINECT module was developed in C# language in Visual Studio environment, while the industrial robot control program was developed in RAPID language in RobotStudio environment. The development of a two-threaded application in RAPID language allowed to separate two independent tasks for the IRB120 robot. The main task of the robot is performed in thread no. 1 (responsible for movement). Simultaneously working thread no. 2 ensures continuous communication with the KINECT system and provides information about the gesture and voice commands in real time without any interference in thread no. 1. The applied solution allows the robot to work in industrial conditions without negative impact of communication task on the time of robot’s work cycles. Thanks to the development of a digital twin of the real robot station, tests of proper application functioning in off-line mode (without using a real robot) were conducted. Obtained results were verified online (on the real test station). Tests of correctness of gesture recognition were carried out, the robot recognized all programmed gestures. Another test carried out was the recognition and execution of voice commands. A difference in the time of task completion between the actual and virtual station was noticed - the average difference was 0.67 s. The last test carried out was to examine the impact of interference on the recognition of voice commands. With a 10dB difference between the command and noise, the recognition of voice commands was equal to 91.43%. The developed computer programs have a modular structure, which enables easy adaptation to process requirements.

The research on the excavation mechanical properties of underpass tunnels has already had certain results, but fewer of them consider the effects of dynamic and static loads on the excavation mechanical properties of underground tunnels at the same time, especially the lack of research cases of double-line highway tunnels with angled underpasses of existing railway tunnels. In this paper, based on the tunnel project of the new double-line Shiqian Highway Tunnel passing under the Hurong Railway at an oblique angle, the mechanical parameters of the rock body in the cross-tunneling area under the influence of static and dynamic load coupling are obtained by using the disturbance quantification coefficients and the Hoek-Brown criterion based on the method of over-advanced geological prediction and the investigation of the surrounding rock on the palisade face, and the engineering-scale finite element model is constructed and the mechanical characteristics of the excavation in the tunnel of the double-lane highway tunnel passing under the existing railroad under the influence of the static and dynamic loads are analyzed. The results show that: the new tunnel rock movement law for the top of the arch sinking, bottom plate bulging, side wall to move outward, the height and width of the arch and bottom plate arch with the tunnel excavation and increase, the side wall rock displacement effect is smaller; left and right lines of the tunnel disturbed area of the rule of change is similar; the existing tunnel bottom plate displacement is more than the top plate and the left and right side walls by the excavation of the time step influence is larger. Typical profile displacement is mainly determined by the distance from the excavation surface; the new tunnel in the four types of calculation conditions of the rock disturbance angle is the same; the existing tunnel roof and side wall Von Mises stress extreme occurs in the tunnel structure, the bottom plate there are pressure relief and pressure-bearing areas; based on the displacement control criteria, the recommended upper and lower step blasting method.

Accurate forecasting of icing thickness has a great significance for ensuring the security and stability of power grid. In order to improve the forecasting accuracy, this paper proposes an icing forecasting system based on fireworks algorithm and weighted least square support vector machine (W-LSSVM). The method of fireworks algorithm is employed to select the proper input features with the purpose of eliminating the redundant influence. In addition, the aim of W-LSSVM model is to train and test the historical data-set with the selected features. The capability of this proposed icing forecasting model and framework is tested through the simulation experiments using real-world icing data from monitoring center of key laboratory of anti-ice disaster, Hunan, South China. The results show that the proposed W-LSSVM-FA method has a higher prediction accuracy and it may be a promising alternative for icing thickness forecasting.

Biomimetic materials are substances that replicate natural structures. There are several methods for producing such materials with highly developed surfaces from a wide range of polymers, but electrospinning is of particular interest due to its simplicity of implementation and the ability to modify the produced fibrous materials resembling structures found in living organisms. This study explores new biomimetic materials based on polyhydroxyalkanoates, specifically poly-3-hydroxybutyrate, modified with chlorophyll derivatives. The research investigates the impact of chlorophyll derivatives on the morphology, supramolecular structure, and key properties of nonwoven materials. The obtained results are of interest for the development of new biomimetic environmentally friendly materials for biomedicine with special properties.

Due to its potential harm to space payload, microwave corona breakdown of microstrip circuits has attracted much attention. This work describes an efficient way to suppress corona breakdown. Since corona breakdown threshold is determined by the highest electric field intensity at the surface of microstrip circuits, lacquer coating with thickness of tens of microns is sprayed on the top of microstrip circuits. The applied dielectric coating is used to move the discharge location away from circuit’s surface which is equivalent to reduce the highest electric field intensity on the in-terface of solid/air of the circuit and thus results into higher breakdown threshold. Two designs of classic coupled-line band-pass filter were used for verification. Corona experimental results at 2.5 GHz show that, in the interested low pressure range (100 to 4500 Pa), 5.3 dB improvement of mi-crowave corona breakdown threshold can be achieved for a filter with narrowest gap of 0.2 mm while its electrical performances like insertion loss, Q-factor are still acceptable. A threshold improvement prediction method is also presented and validated.

Nonlinear nonparametric statistics (NNS) algorithm offers new tools for curve fitting. A relationship between k-means clustering and NNS regression points is explored with graphics showing a perfect fit in the limit. The goal of this paper is to demonstrate NNS as a form of unsupervised learning, and supply a proof of its limit condition. The procedural similarity NNS shares with vector quantization is also documented, along with identical outputs for NNS and a k nearest neighbours classification algorithm under a specific NNS setting. Fisher's iris data and artificial data are used. Even though a perfect fit should obviously be reserved for instances of high signal to noise ratios, NNS permits greater flexibility by offering a large spectrum of possible fits from linear to perfect.

A thorough analysis and comparison of the fatty acid profiles of stipe and blade from Laminaria hyperborea, a kelp species found in the northern Atlantic, is presented. Lipids were extracted and fractionated into neutral lipids, free fatty acids and polar lipids, then derivatized to fatty acid methyl esters prior to GC-MS analysis. A total of 42 fatty acids were identified and quantified, including the n-3 fatty acids α-linolenic acid, stearidonic acid and eicosapentaenoic acid. An n-6/n-3 ratio of 0.8:1 was found in blade and 3.5:1 in stipe, respectively. The ratios vary between the lipid fractions within stipe and blade, with the lowest ratio in the polar lipid fraction of blade. The fatty acid amounts are higher in blade than in stipe, and the highest amounts of n-3 fatty acids are found within the neutral lipid fractions. The amounts of polyunsaturated fatty acids are 3.4 times higher in blade than stipe. This study highlights the compositional differences between the lipid fractions of stipe and blade from L. hyperborea. The amount of polyunsaturated fatty acids, compared to saturated- and monounsaturated fatty acids, as well as the n-6/n-3-ratio, is known to influence human health. In the pharmaceutical, food, and feed industries this can be of importance for production and sale of different health products. Additionally, lipids are today among the unused by products of alginate production, exploiting this material for commercial interest should give both economical and environmental benefits.

Multimodal user interfaces promise a natural and intuitive human machine interactions. But is the extra effort for the development of a complex multi-sensor system justified, or can users also be satisfied with one input modality already? This study investigates interactions in an industrial weld inspection workstation. Three unimodal interfaces, including spatial interaction with buttons augmented on a workpiece or a worktable, and speech commands, were tested individually and in a multimodal combination. Within the unimodal conditions, users preferred the augmented worktable, but overall, the interindividual usage of all input technologies in the multimodal condition was ranked best. Our findings indicate that the implementation and use of multiple input modalities is valuable, and that it is difficult to predict the usability of individual input modalities for complex systems.

2.25Cr-1Mo steel with high strength at high temperatures and good hydrogen resistance is widely used for power generation boiler material in high temperature and pressure use environments. Following the test evaluation of the ASME Boiler and Pressure Vessel Code, specimens from the base metal of a boiler pipe were found to have impact toughness values of 285 and 21 ft-lb, which are drastically different values. The analysis of the fracture surface of the 21 ft-lb test specimen revealed MnS inclusions, and it was found that cracks initiated at the inclusions. Observation of the cross-section of the crack propagation front revealed that cracks propagated along the ferrite regions and precipitate voids. Inclusions were also found in the 285 ft-lb impact specimen; however, the volume fraction of the inclusions was significantly less than that of the 21 ft-lb specimen. It was also found that the ferrite and carbide content of the 285 ft-lb specimen was less than 21 ft-lb specimen. The reason that the inclusions, ferrite, and carbide content differed in the two adjacent impact test specimens was analyzed. The effects of micro-segregation, such as MnS inclusions on ferrite and carbide, were compared and analyzed.

Many spectroscopic diagnostics are routinely used as a technique to infer the plasma parameters from line emission spectra but their accuracy depends on the numerical model or code used for the fitting process. However, the validation of a line shape code requires some steps : comparison of the line shape code with other similar codes for some academic (simple) cases and then more complex ones, comparison of the fitting parameters obtained from the best fit of the experimental spectra with those obtained with other diagnostic techniques and/or comparison of the fitting parameters obtained by different codes to fit the same experimental data. Here we compare the profiles of the hydrogen Balmer β line in a helium plasma computed by six codes for a selected set of plasma parameters and we report on the plasma parameters inferred by each of them from the fitting to a number of experimental spectra measured in a helium corona discharge where the pressure was in the range 1- 5 bar.

Sports video analysis is an interesting and emerging field in the domain of computer vision. It has become a very popular subject among scholars all over the world in the last decade due to the need of automated classification of events such as offsides, in/out situations, goals and so on. The most important problem in sports video analysis is detection and tracking of ball and players. Extraction of court lines is also another important problem since it is necessary in the classification of aforementioned events. In this study, considering some of the previous work on the subject, we develop a method for tracking the ball and players in tennis videos where the camera position and orientation is supposed fixed.

Our objective was to investigate the effects of topically applied neuropeptide Y (NPY) on ischemic wounds. Initially, the animal model for ischemic wound healing was validated using 16 male Sprague-Dawley albino rats. In the intervention study, an additional 28 rats were divided into three groups: NPY (0.025%), the positive control insulin-like growth factor-I (IGF-I, 0.0025%), and the hydrogel carrier alone (control). The hydrogel was selected due to its capacity to prolong NPY release (p &lt; 0.001), as demonstrated in a Franz diffusion cell. In the animals, an 8-mm full-thickness wound was made in a pedunculated dorsal ischemic skin flap. Wounds were then treated and assessed for 14 days, and procured at the end of the experiment for in situ hybridization analysis (RNAscope®) targeting NPY receptor Y2R and for meticulous histologic examination. Wound healing rates, i.e. the percentage wound area changes, did not show an increase with NPY (p = 0.938) but did with rhIGF-I (p = 0.039) compared to the control. Y2R mRNA was not detected in the wounds or adjacent skin but was identified in the rat brain (positive control). Light microscopic examination revealed trends of increased angiogenesis and enhanced inflammatory cell infiltration with NPY compared to control. An interesting secondary discovery was the presence of melanophages in the wounds. Our findings suggest the potential of NPY to enhance neovascularization under ischemic wound healing conditions, but further optimization of the carrier and dosage is necessary. The mechanism is elusive but likely involves NPY receptor subtypes other than Y2R.

A novel quasi-twisted miniaturized wideband Branch Line Coupler (BLC) is proposed. The design is based on bisecting the conventional microstrip line BLC transversely and folding bisected sections on double-layered substrates with a common ground plane in between. The pair of quarter wavelength horizontal parallel arms is converted to a Z-shape meandered microstrip line in the designed structure. On the other hand, the pair of quarter wavelength vertical arms are cut by half into two lines and converted to a periodically loaded slow wave structure. The bisected parts of BLC are placed on the opposite side of the doubled-layer substrate and connected through four vias passing through the common ground plane. This technique enabled a compact BLC size of 6.4×18 mm2, which corresponds to a surface area miniaturization by ~50% as compared to the classical BLC size of 10×23 mm2 at 6GHz, Moreover, the attained relative bandwidth is 73.9% (4.6-10 GHz) for S11, and 75.8% (4.5-10 GHz) for S33 as compared to 41% for the ordinary BLC at the same resonant frequency. The circuit is constructed on a double-layered low-cost FR4 substrate with a relative permittivity of 4.3, and a loss tangent of 0.025. An isolation of -13dB was realized in both S13 and S31 demonstrating an excellent performance. The transmission coefficients between input/output ports S21, S41, S23, and S43 are between -3.1dB to -3.5dB at the frequency of 6GHz. Finally, the proposed BLC provides phase differences between output ports of 90.5o and 94.8o at the frequency of 6GHz when the input ports 1 and 3 are excited, respectively. The presented design offers the potential of being utilized as a unit cell for building a Butler-matrix (BM) for sub-6GHz 5G beamforming networks.

Many people in the USA have lost their lives or become addicted to opioids via prescription opioids given for chronic pain. The chronic pain epidemic has emerged due to a convergence of factors, including the medicalization of pain as well as injuries happening in the workplace, in the home, or during recreation. Opioid prescriptions rose precipitously from the late 1990’s through to approximately 2020, and despite public awareness, still are increasing. This review examines literature on integrative approaches to chronic pain as delineated by pain type. The review is organized by the most common causes of chronic pain, and randomized controlled trials, meta-analyses and systematic reviews are extracted for each cause of chronic pain. Several promising interventions may alleviate chronic pain of some causes, and some interventions may work across pain causes. Lowering inflammation through dietary or lifestyle regimens may be a general way of reducing pain. Pain can be alleviated through several adjunctive and integrative treatment approaches, which may serve to lower the need for opioid medication.

(1) Background: In this work, a series of benzimidazole derivatives containing colchicine-like and cathechol-like moieties with methyl group substitution in the benzimidazole ring were evaluated for their in vitro antiproliferative, pro-apoptotic and antioxidative activity against highly invasive breast cancer cell line MDA-MB-231 and related impairment of tubulin dynamics; (2) Methods: MTT assay was used to evaluate the antiproliferative activity. In vitro tubulin polymerization assay as well as docking analysis was applied to prove the alterations in tubulin polymerization. Immunofluorescent and DAPI staining reveal the pro-apoptotic potential of benzimidazole derivatives and the effect on tubulin’s dynamics in living cells. The antioxidant activity was evaluated by scavenging of H2O2 and hypochlorite ion and ortho-phenanthroline tests; (3) Results: The compounds containing colchicine-like moiety displayed significant growth inhibitory effect against cancer cell line as was highlighted the role of methyl functional group on the tubulin aggregation and blockage of mitosis. All compounds showed an ability to scavenge H2O2, while the compounds with cathecol-like moiety were more effective against hypochlorite ion and chelation of iron; (4) Conclusions: The benzimidazole derivative containing colchicine-like moiety and methyl group substitution in benzimidazole ring is a potential antiproliferative and microtubule destabilizing agent.

Background: The aim of this study was to investigate a series of complete blood cell count – based biomarkers of systemic inflammation as predictors of clinical outcomes in patients who underwent first-line chemoimmunotherapy for advanced NSCLC. Methods: Consecutive patients with pathologically diagnosed stage III/IV NSCLC who underwent first-line chemoimmunotherapy were retrospectively enrolled. The clinical outcomes used for biomarker evaluation were Objective Response Rate (ORR) and Overall Survival (OS). Results: Non-responders had significantly higher values of neutrophil to lymphocyte ratio (NLR, median: 5.36; IQR: 2.78–10.82 vs. 3.31; IQR: 2.15–4.12, p = 0.019), neutrophil to monocyte ratio (NMR, median: 14.00; IQR: 8.82–21.20 vs. 9.20; IQR: 7.45–11.20, p = 0.013), and systemic inflammation index (SII, median: 1,395; IQR: 929–3,334 vs. 945; IQR: 552–1,373, p = 0.025), but only NLR and NMR remained independently related with clinical response in multivariate logistic regression. In univariate analysis white blood cells (OR:1.2202; 95% CI: 1.0339 - 1.4400, p=0.019), neutrophils (OR:1.2916; 95% CI: 1.0692 - 1.5604, p=0.008), NLR (OR:1.3601: 95% CI: 1.0949 - 1.6896, p=0.005) and NMR (OR:1.2159; 95% CI: 1.00396 - 1.4221, p=0.015) were significantly associated with survival; Cox regression models confirmed that neutrophils, NLR and MLR were independently associated with survival; NLR at a cut-off value of 4.0 showed the better AUC (0.749) in predicting survival. Conclusions: Baseline complete blood cell count biomarkers, especially the NLR, can predict clinical outcomes in patients with advanced NSCLC treated with first-line chemoimmunotherapy.

This paper investigates the effects of various process parameters, specifically the substrate temperature, on weld track geometry in Directed Energy Deposition (DED) processes. A specialized experimental setup integrated within a DED machine facilitates controlled thermal conditioning of sample sheets. Through Design of Experiments (DoE) methods, individual weld marks are generated and analysed to assess geometric characteristics. Regression models are constructed to predict machine parameters for desired weld geometry at different substrate temperatures. Validation experiments confirm the accuracy and reliability of the regression models. Results show a consistent trend towards target geometric features across a broad range of substrate temperatures. Despite deviations in measured values, successful fabrication is achieved, demonstrating robust bonding between weld and substrate. Contact angle predictions exhibit precision within a partial temperature range for proper deposition. The developed model offers insights for optimizing DED process parameters to achieve desired weld characteristics, advancing the capabilities and reliability of additive manufacturing technology. Future work aims to refine the regression model and explore additional mathematical relationships for enhanced accuracy. An implication of this work is the potential to vary the local mechanical properties of parts by controlling the temperature profile while maintaining consistent geometric characteristics. By manipulating the substrate temperature, it may be possible to tailor the microstructure and mechanical properties of fabricated components in the future to meet specific requirements in different regions of the part.

The strictness of the result of an excavation, whether mechanical or by means of explosives, is naturally conditioned by the objective, and therefore by the type of technique applied to achieve it. To attain the best results in terms of rock breakage and respect of the final profile, it’s important to evaluate the excavation specific energy and its optimization. This research focuses on evaluating the effects of different techniques on the quality of final walls in open-pit and underground operations. Different geometries and configurations can be applied to both quarrying and tunnelling blasts. The research is aimed to push contour blasts to their limits, and the main aspects are discussed in order to improve the blast parameters in the daily practice.

The Italian herbal products market is the most prosperous in Europe. The proof is represented by the use of these products in several marketing categories, ranging from medicine to nutrition and cosmetics. Market and legislation in Italy are at the same time cause and consequence of this peculiar situation. In fact, the legislation on botanical food supplements in Italy is very permissive and at the same time the market shows an overall satisfaction of users and strong feedback in terms of consumption, which brings a widening use of medicinal plants, formerly the prerogative of pharmaceuticals, to other fields such as nutrition. This review summarizes the market and normative panorama of herbal products in Italy, highlighting the blurred boundaries of health indications, marketing authorizations and quality controls between herbal medicines and non pharmaceutical products, such as food supplements, cosmetics and other herbal-based “parapharmaceuticals”.

Our skin epidermis constitutes the most important innate defense barrier against all pathogens. Therefore, even if skin lesions are common due to infections, scarring, genetic disorders, and other diseases, skin integrity is crucial for maintaining body homeostasis. Marine collagen peptides (MCPs) and Glycosaminoglycans (GAGs) have been described as potential wound healing (WH) agents. Recently, through an ex vivo clinical approach, we have demonstrated the nutricosmetic potential of fish cartilage hydrolysate (FCH), which presents a combination of collagen peptides and GAGs. Here, we coupled a clinical approach with in vitro experiments on human dermal fibroblasts (HDFs) and applied a Data Independent Acquisition - Parallel Accumulation Serial Fragmentation (diaPASEF) proteomic analysis, to assess the potential benefit of FCH in WH and its mode of action. Our results show that human serum enriched with circulating metabolites resulting from FCH ingestion, improved wound closure in scratch assays. In support, some proteins with anti-inflammatory and immunomodulatory properties or prone to promote hydration and extracellular matrix (ECM) stability showed increased expression in HDFs, after exposure to FCH-enriched serum. These findings suggest that FCH appears as a promising nutrient for WH and skin regeneration.

The discovery by the Large Area Telescope on board Fermi of variable gamma-ray emission from radio-loud narrow-line Seyfert 1 (NLSy1) galaxies revealed the presence of a possible third class of AGN with relativistic jets in addition to blazars and radio galaxies. Considering that NLSy1 are usually hosted in spiral galaxies, this finding poses intriguing questions about the nature of these objects and the formation of relativistic jets. We report on a systematic investigation of the gamma-ray properties of a sample of radio-loud NLSy1, including the detection of new objects, using 7 years of Fermi-LAT data with the new Pass 8 event-level analysis. In addition we discuss the radio-to-very-high-energy properties of the gamma-ray emitting NLSy1, their host galaxy, and black hole mass in the context of the blazar scenario and the unification of relativistic jets at different scales.

Many signaling pathways, molecular and cellular actors which are critical for wound healing have been implicated in cancer metastasis. These two conditions are a complex succession of cellular biological events and accurate regulation of these events is essential. Apart from inflammation, macrophages-released ROS arise as major regulators of these processes. But, whatever the pathology concerned, oxidative stress is a complicated phenomenon to control and requires a finely tuned balance over the different stages and responding cells. This review provides an overview of the pivotal role of oxidative stress in both wound healing and metastasis, encompassing the contribution of macrophages. Indeed, macrophages are major ROS producers but also appear as their targets since ROS interfere with their differentiation and function. Elucidating ROS functions in wound healing and metastatic spread may allow the development of innovative therapeutic strategies involving redox modulators.

Efficient quality evaluation provides support for the timely and good maintenance of the lane line marking. This paper searches and optimizes the back propagation(BP) network model which referred to the analytic hierarchy process(AHP) model structure, as well as the number of nodes in the middle layer network. Based on this, a comprehensive evaluation method of multi-dimensional lane line quality such as shape, color and contrast is established. The experimental results show that the parameters of the model are more simplified, and the scoring and classification results of lane lines are more accurate.

We provide a very general review of the resonant transmission line method for optical fiber problems. The method has been found to work seamlessly for a variety of difficult problems including elliptical and eccentric core fibers as well as “holey”, photonic crystal fibers. A latest version has been shown to offer great versatility with respect to cases of unconventional, inhomogeneous index profiles.

In an industrial environment, the quality assurance of weld seams requires extensive efforts. The most commonly used methods for that are expensive and time-consuming destructive tests, since quality assurance procedures are difficult to integrate into production processes. Beyond that, available test methods allow only the assessment of a very limited set of characteristics. They are either suitable for determining selected geometric features or for locating and evaluating internal seam defects. The presented work describes an evaluation methodology based on microfocus X-ray computed tomography scans (µCT scans) which enable the 3D characterization of weld seams, including internal defects such as cracks and pores. A 3D representation of the weld contour, i.e., the complete geometry of the joint area in the component with all quality-relevant geometric criteria, is an unprecedented novelty. Both the dimensions of the weld seam and internal defects can be revealed, quantified with a resolution down to a few micrometers and precisely assigned to the welded component. On the basis of the methodology developed within the framework of this study, the results of the scans performed on the alloy AA 2219 can be transferred to other aluminum alloys. In this way, the data evaluation framework can be used to obtain extensive reference data for the calibration and validation of inline process monitoring systems employing Deep Learning-based data processing.

Hepatocellular carcinoma (HCC) is a heterogeneous malignancy with complex carcinogenesis. Although there has been significant progress in the treatment of HCC over the past decades, drug resistance to chemotherapy remains a major obstacle in its successful management. In this study we were able to reduce chemoresistance in cisplatin-resistant HepG2 cells by either silencing the expression of transglutaminase type 2 (TG2) using siRNA or by pre-treatment of cells with the TG2 enzyme inhibitor cystamine. Further analysis revealed that, whereas the full-length TG2 isoform (TG2-L) was almost completely cytoplasmic in its distribution, the majority of the short TG2 isoform (TG2-S) was membrane-associated in both parental and chemoresistant HepG2 cells. Following induction of cisplatin toxicity in non-chemoresistant parental cells, TG2-S together with cisplatin quickly relocated to the cytosolic fraction. Conversely, no cytosolic relocalisation of TG2-S or nuclear accumulation cisplatin was observed following identical treatment of chemoresistant cells, where TG2-S remained predominantly membrane-associated. This suggests that deficient subcellular relocalisation of TG2-S from membranous structures into the cytoplasm may limit the apoptic response to cisplatin toxicity in chemoresistant cells. Structural analysis of TG2 revealed the presence of binding motifs for interaction of TG-S with the membrane scaffold protein LC3/LC3 homologue that could contribute to a novel mechanism of chemotherapeutic resistance in HepG2 cells.

Distributed Energy Resources might have a severe influence on Power Line Communications, as they can generate interfering signals and high frequency emissions or supraharmonics that may cause loss of metering and control data. In this paper, the influence of various energy resources on Narrowband Power Line Communications is described and analyzed through several test measurements performed in a real microgrid. Accordingly, the paper describes the effects on smart metering communications through MAC layer analysis. Results show that the commutation frequency of inverters and the presence of battery chargers are remarkable sources of disturbance in low voltage distribution networks. In this sense, the results presented can contribute to efforts towards standardization and normative of emissions at higher frequencies higher, such as CENELEC EN 50160 and IEC/TS 62749.

Copper (Cu) is a critical element for cancer cell proliferation and considerably accumulates in the nucleus. 64Cu2+ is an anticancer radiopharmaceuticals targeting the copper requirement of cancer cells. However, intravenously injected 64Cu2+ ions primarily accumulate in the liver. Ligand complexation of 64Cu2+ would be a promising method for increasing tumor delivery by reducing liver uptake. Herein, we used three tripodal amine ligands [tris(2-aminoethyl)amine (Tren), diethylenetriamine (Dien), and tris(2-pyridylmethyl)amine (TPMA)] to enclose 64Cu2+ ions and compared their in vivo tumor and liver uptake using a tumor-bearing xenograft mouse model of the extrahepatic bile duct carcinoma cell line TFK-1. We examined intracellular Cu distribution using microparticle-induced X-ray emission (micro-PIXE) analysis for these compounds. 64Cu2+-Tren and 64Cu2+-Dien showed higher tumor uptake than 64Cu2+-TPMA and 64Cu2+ ions in TFK-1 tumors. Among the three 64Cu2+ complexes and 64Cu2+ ions, liver uptake was inversely correlated with tumor uptake. Micro-PIXE analysis showed that in vitro cellular uptake was similar to in vivo tumor uptake and nuclear delivery was the highest for 64Cu2+-Tren. Conclusively, an inverse correlation between tumor and liver uptake was observed using three 64Cu2+ complexes of tripodal amine ligands and 64Cu2+ ions. These results provide useful information for the future development of anticancer 64Cu radiopharmaceuticals.

We address the unsolved question of how best to estimate the collision entropy, also called quadratic or second order Rényi entropy. Integer-order Rényi entropies are synthetic indices useful for the characterization of probability distributions. In recent decades, numerous studies have been conducted to arrive at their valid estimates starting from experimental data, so to derive suitable classification methods for the underlying processes, but optimal solutions have not been reached yet. Limited to the estimation of collision entropy, a one-line formula is presented here. The results of some specific Monte Carlo experiments give evidence of the validity of this estimator even for the very low densities of the data spread in high-dimensional sample spaces. The method strengths are unbiased consistency, generality and minimum computational cost.

Fuel consumption, subsequent emissions and safe operation of class 8 vehicles are of prime importance in recent days. It is imperative that the vehicle operates in its true optimal operating region given a variety of constraints such as road grade, load, gear shifts, Battery State of charge (for hybrid vehicles), etc. In this paper a research study is conducted to evaluate the fuel economy and subsequent emission benefits when applying predictive control to a mild hybrid line haul truck. The problem is solved using a combination of dynamic programming with back tracking and model predictive control. The specific fuel saving features that are studied in this work are dynamic cruise control, gear shifts, vehicle coasting and torque management. These features are evaluated predictively as compared to a reactive behavior. The predictive behavior of these features are a function of road grade. The result and analysis shows significant improvement in fuel savings along with NOx benefits. Out of the control features dynamic cruise (predictive) control and dynamic coasting showed the most benefits while predictive gear shifts and torque management (by power splitting between battery and engine) for this architecture did not show fuel benefits but provided other benefits in terms of powertrain efficiency.

Local binary pattern is one of the visual descriptors and can be used as a powerful feature extractor for texture classification. In this paper, a novel representation for face recognition is proposed, called it Bilateral Line Local Binary Patterns (BL-LBP). This scheme is an extension of Line Local Binary Patterns descriptors in the statistical learning subspace. The present bilateral descriptors are fused with an ensemble learning of calibrated SVM models. The performance of this scheme is evaluated using 5 standard face databases. It is found that it is robust against illumination variation, diverse facial expressions and head pose variations and its recognition accuracy reaches 98 percent, running on a mobile device with a processing speed of 63 ms per face. Results suggest that our proposed method can be very useful for the vision systems that have limited resources where the computational cost is critical.

Currently, narrowband Power line communication (PLC) is considered as an attractive communication system in smart grid environments for applications such as advanced metering infrastructure (AMI). In this paper, we will present a comprehensive comparison and analysis in time and frequency domain of noise measured in China and Italy. In addition, impulsive noise in these two countries are mainly analyzed and modeled using two probability based models, Middleton Class A (MCA) model and \(\alpha\) stable distribution model. The results prove that noise measured in China is rich in impulsive noise, and can be modeled well by \(\alpha\) stable distribution model, while noise measured in Italy has less impulsive noise, and can be better modeled by MCA model.

The asymmetric bimodal exponential power (ABEP) distribution is an extension of the generalized gamma distribution to the real line via adding two parameters which fit the shape of peakedness in bimodality on real line. The special values of peakedness parameters of the distribution are combination of half Laplace and half normal distributions on real line. The distribution has two parameters fitting the height of bimodality, so capacity of bimodality is enhanced by using these parameters. Adding a skewness parameter is considered to model asymmetry in data. The location-scale form of this distribution is proposed. The Fisher information matrix of these parameters in ABEP is obtained explicitly. Properties of ABEP are examined. Real data examples are given to illustrate the modelling capacity of ABEP. The replicated artificial data from maximum likelihood estimates of parameters of ABEP and distributions having an algorithm for artificial data generation procedure are provided to test the similarity with real data.

When the distance between an obstacle and a power line is less than the discharge distance, a discharge arc can be generated, resulting in interruption of power supplies. Therefore, regular safety inspections are necessary to ensure safe operations of power grids. Tall vegetation and buildings are the key factors threatening the safe operation of extra high voltage transmission lines within a power line corridor. Manual or LiDAR based-inspections are time consuming and expensive. To make safety inspections more efficient and flexible, a low-altitude unmanned aerial vehicle remote-sensing platform equipped with optical digital camera was used to inspect power line corridors. We propose a semi-patch matching algorithm based on epipolar constraints using both correlation coefficient and the shape of its curve to extract three dimensional (3D) point clouds for a power line corridor. Virtual photography was used to transform the power line direction from approximately parallel to the epipolar line to approximately perpendicular to epipolar line to improve power line measurement accuracy. The distance between the power lines and the 3D point cloud is taken as a criterion for locating obstacles within the power line corridor automatically. Experimental results show that our proposed method is a reliable, cost effective and applicable way for practical power line inspection, and can locate obstacles within the power line corridor with measurement accuracies better than ±0.5 m.

The extraction of cell cultures from fresh tissue is a process that requires significant computa-tional resources and is associated with substantial overheads. The objective of our research is to de-vise a rapid, straightforward, and efficient technique for the cultivation of neuronal cells derived from frozen biological material. We utilized freshly isolated hippocampus and cerebral cortex tissue from rats, in addition to whole brain tissue. This tissue underwent digestion and processing to yield a cellular suspension. This suspension was subsequently cryopreserved using a variety of cryopro-tectants: CTS™ Synth-a-Freeze™, SpermFreeze®, and a medium supplemented with 10% DMSO. CTS™ Synth-a-Freeze™ is a commercially available cryoprotectant typically employed in the preservation of cellular cultures, while the addition of 10% DMSO to the medium is a conventional technique for the cryopreservation of cells to mitigate damage. The innovative aspect of our meth-odology is the application of SpermFreeze®, a product used for the cryopreservation of sperm in in vitro clinics. We postulated that SpermFreeze® might enhance the viability and quality of the cryo-preserved neuronal cells, given the delicate and energetically demanding nature of both sperm and neuronal cells. The ultimate objective was to ascertain whether a cryoprotectant formulated for sperm could augment the post-thawing efficacy of our nervous system cells. This investigation intro-duces an innovative methodology for the optimization of neuronal cell isolation and cryopreserva-tion from animal-derived tissues.

Cancer cell lines are widely used as in vitro models of tumorigenesis, facilitating fundamental discoveries in cancer biology and translational medicine. Currently, there are few options for glioblastoma (GBM) treatment and limited in vitro models with accurate genomic and transcriptomic characterization. Here, a detailed characterization of a new GBM cell line, namely AHOL1, was conducted in order to fully characterize its molecular composition based on its copy number alteration (CNA) and transcriptome profiling, followed by the validation of key elements associated with GBM tumorigenesis. Large numbers of CNAs and differentially expressed genes (DEGs) were identified. CNAs were distributed throughout the genome, including gains at Xq11.1-q28, Xp22.33-p11.1, Xq21.1-q21.33, 4p15.1-p14, 8q23.2-q23.3 and losses at Yq11.21-q12, Yp11.31-p11.2 and 12p13.31 positions. Nine druggable genes were identified, including HCRTR2, ETV1, PTPRD, PRKX, STS, RPS6KA6, ZFY, USP9Y and KDM5D. By integrating DEGs and CNAs, we identified 57 overlapping genes enriched in fourteen pathways. Altered expression of several cancer-related candidates found in the DEGs-CNA dataset was confirmed by RT-qPCR. Taken together, this first comprehensive genomic and transcriptomic landscape of AHOL1 provides unique resources for further studies and identifies several druggable targets that may be useful for therapeutics and biologic and molecular investigation of GBM.

In this investigation steel P355NH has been successfully cladded with Inconel 625 through the method of explosive welding. Explosively welded bimetal clad-plate was subjected to the two separated post weld heat treatment processes: stress relief annealing (at 620oC for 90 minutes) and normalizing (at 910oC for 30 minutes). In order to analyze the microstructure of the joint in the as-welded state and to investigate the influence of the post weld heat treatment on it, the light and scanning electron microscope observations and microhardness analysis have been performed. The examination of the diffusion zone microstructure has been performed by using the scanning transmission electron microscope. It was stated that obtained joint has characteristic wavy-shape geometry with the presence of the melted zones and severe deformed grains of both joined materials. Strain hardening of the materials in joint zone was established with microhardness analysis. In both of the heat treatments the changes in the grain structure have been observed. The normalizing heat treatment has the most significant impact on the microstructure of the joint as well as the concentration of the chemical elements in the joint zone. It was reported that due to normalizing the diffusion zone has been formed together with precipitates in the joint zone. The analysis of the diffusion zone images leads to the conclusion that the diffusion of alloying elements from Inconel 625 to steel P355NH takes place along the grain boundaries with additional formation of the voids in this area. The precipitates in Inconel 625 in the joint zone are two type of carbides – chromium-rich and molybdenum-rich. Scanning transmission electron microscope observation of the grain microstructure in the diffusion zone shows that this area consists of equiaxed grains (from the side of Inconel 625 alloy) and columnar grains (from the side of steel P355NH).

A signed graph is an undirected graph such that all of its edges are labeled positive or negative. Let D be an embedding of a signed graph G in the Euclidean line. If in D for all of the vertices their positive neighbors are closer than the negative neighbors, then D is called a valid drawing of G. In this paper we show that signed trees, unicyclic graphs, and ladder graphs have a valid drawing in the Euclidean line.

We introduce a modelling framework for the investigation of on-line machine learning processes in non-stationary environments. We exemplify the approach in terms of two specific model situations: In the first, we consider the learning of a classification scheme from clustered data by means of prototype-based Learning Vector Quantization (LVQ). In the second, we study the training of layered neural networks with sigmoidal activations for the purpose of regression. In both cases, the target, i.e. the classification or regression scheme, is considered to change continuously while the system is trained from a stream of labeled data. We extend and apply methods borrowed from statistical physics which have been used frequently for the exact description of training dynamics in stationary environments. Extensions of the approach allow for the computation of typical learning curves in the presence of concept drift in a variety of model situations. First results are presented and discussed for stochastic drift processes in classification and regression problems. They indicate that LVQ is capable of tracking a classification scheme under drift to a non-trivial extent. Furthermore, we show that concept drift can cause the persistence of sub-optimal plateau states in gradient based training of layered neural networks for regression.

For a given set of plasma parameters, along a single series (Lyman, Balmer etc) the lines with higher principal quantum number(n) lines get progressively wider, closer to each other, and start merging for a certain critical n. In the present work four different codes(with further options) are used to calculate the entire Balmer series for moderate and high electron densities. Particular attention is paid to the relevant physics, such as the cutoff criteria, strong and penetrating electron collisions.

RFID based technology innovated a new field of wireless sensing, which has been applied in posture recognition, object localization and the other sensing fields, the existing sensing methods often require tags to be attached to dynamic targets (because RFID signals are more sensitive to moving target), significantly limiting their applications. It is a challenging task to sensing a static target without tag attached in NLOS (Non-Line-of-Sight). We utilized RFID technologies to sense the static foreign objects in agricultural products, and taken metal, rock, rubber and clod as sensing targets that are common in agricultural. By deploying a tag matrices to create a sensing region, we observed the signal variations before and after the appearance of the targets in this sensing region, determined the targets’ positions and their types. Here, we buried the targets in the media of seedless cotton and wheat, and detected static targets with a non-contact method in the NLOS. Researches illustrated that by deploying appropriate tag matrices and adjusting the angle of a single RFID antenna, the matrices signals can be sensitive to the static targets’ positions and their properties,i.e. matrices signals vary with different targets and their positions. Specifically, we achieved a 100% success rate in locating metallic targets, while the success rate for clods was the lowest at 86%. We achieved a 100% recognition rate for the types of all the four objects.

This paper discusses a MEMS switch that can be fabricated using low temperature (<100^oC) deposition and patterning techniques suitable for the back-end-of-the-line integration with CMOS. The resulting cross-bar switches can be used for electrostatic discharge protection, FPGA implementation, chip security assessment and lock-down, and circuit block power management. We discuss platinum and iron switch with turn-on voltages of ~ 1.8 V. In the case of the iron switches, we also show that they can be magnetized to have “memory” and stay on when turned on. Platinum switch cycling of up to 1000 times did not show any changes in their turn-on voltage and their contact resistance was unchanged. The 10-100 nm switch airgaps were formed using low temperature sputtered sacrificial polysilicon and XeF₂ etching. XeF₂ does not attack any of the metals used in CMOS enabling fabrication of cross-bar switches with any of these metals. Once activated, it takes ∿ 6 to mechanically turn on the switch that can be decreased to ~1 ns by optimizing the device structure. Interestingly, the nm-scale gaps can be used as spark gap as a fast plasma switch to discharge first followed by the activation of the MEMS switch.

With the breakthrough of modernism, various efforts are undertaken to rationalize architecture and building processes using industrial principles. Few architects explore these as intensively as Walter Gropius, the founder of the Bauhaus. Even before World War One, and increasingly in the interwar years, Gropius and a number of colleagues undertake various experiments which manifest in a series of projects, essays, model houses and Siedlungen. These aim at conceptually different goals, i.e. they follow two different categories of industrial logic: first, a flexible construction kit and, second, an assembly line serial production. This article traces the genesis of these two concepts and analyses their characteristics using these early manifestations. Compared to existing literature, this article takes into account hitherto neglected primary sources as well as technological and construction history aspects—allowing for a distinction based not only on theoretical, but also technological and structural characteristics. This article shows that Gropius succeeds in formulating and exploring the two principles in theory and practice as well as drawing conclusions by the end of the 1920s. With them, he contributed significantly to the rationalization of architecture, and his principles have been picked up and developed further by numerous architects since then.

Coagulase negative Staphylococci (CoNS) are reported to be responsible for 50-60% of bloodstream infections in very preterm (&lt;1500 g) infants in Neonatal Intensive Care Units (NICU). Staphylococcus capitis is an increasingly prevalent pathogen in neonatal setting, frequently causing central-line associated bloodstream infections (CLABSI) that can be difficult to eradicate. CVC removal versus in situ treatment of CoNS CLABSIs is a matter of debate, with no clear consensus emerging in the existing literature. We revised all S. capitis CLABSIs in our NICU between 2019 and 2022, focusing on the role of catheter removal for eradication. Among 25 cases, 17 CVCs were removed after diagnosis, leading to a 76.5% eradication rate in this group. 3 infants had a persistently positive blood culture after CVC substitution. A new catheter was than inserted after a 48-hours washout period, resulting in resolution of the infection. Only 2 of 8 patients (25%) who retained the catheter after diagnosis, underwent infection eradication with antibiotic therapy alone. Catheter removal, when feasible, seems to be the most effective strategy to eradicate S. capitis CLABSIs, sometimes even requiring a 48-hours washout period before reinsertion. Further studies on this subject are needed to better standardize the management of this kind of infections.

We propose a spectral filter based on Plastic Optical Fiber with micro-holes as a low-cost, robust, and highly reproducible spectral filter. The spectral filter is explored for two configurations: fiber extended in a straight line, and a fiber optic loop mirror scheme configuration. The transmission traces indicate a spectral blue shift of peak transmission, at 587 nm, 567 nm, 556 nm, and 536 nm for 0, 1, 2, and 3 holes in the fiber, respectively. The filter exhibits a bandpass period of approximately 120 nm. Additionally, we conducted a comparison of the transmission with holes separated by distances of 1 cm and 500 μm. The results demonstrate that the distance between holes does not alter the spectral transmission of the filter. In the case of the fiber loop mirror configuration, we observed that the bandpass can be adjusted, suggesting the presence of multimode interference. Exploring variations in the refractive index within the holes by filling them with glucose solutions at various concentrations, we determined that the filtering band and spectral shape remains unaltered, ensuring a stable and robust operation of our spectral filter.

Idiosyncratic drug induced liver injury (DILI) is an unpredictable reaction of exposed individual on a certain drug, and the drug-induced autoimmune hepatitis (DIAIH) presents a DILI phenotype that mimics idiopathic autoimmune hepatitis (AIH) when considering the clinical, biochemical, serological and histological parameters. We present a case of a 48-year-old male that was hospitalized due to severe hepatocellular liver injury two months after the self-treatment with the muscle-building dietary supplement based on arginine-alpha-ketoglutarate, L-citrulline, L tyrosine, creatine malate and beet extract. His immunology panel was positive with increased IgG levels, and the radiologic methods showed no signs of chronic liver disease. He underwent corticosteroid treatment with adequate response. After the therapy withdrawal, a clinical relapse occurred. Seven months after the initial presentation liver MR suggested the initial cirrhotic changes of the right liver lobe. Liver biopsy revealed abundant lymphoplasmacytic infiltrate with piecemeal necrosis and grade 2 fibrosis. He responded well on the corticosteroid treatment again, and was further treated with low dose prednisone without additional relapses. Several years later, further management confirmed presence of liver cirrhosis with no histological or biochemical signs of the disease activity. DIAIH is a DILI phenotype difficult to distinguish from idiopathic AIH despite a wide armamentarium of diagnostic methods. Regular patient monitoring and clinical open-mindedness with the adjustment of therapeutic approaches according to the disease course are more important than strict labelling of the disease.

A closed form solution for the common and differential modal currents induced on a pair of infinitely long parallel conductors by a voltage source was derived. For lossy conductors the current consists of a continuous spectrum of radiation modes and (for the common mode) a modified low loss Sommerfeld-Goubau mode and (for the differential mode) a quasi-TEM mode. This model is used to investigate the influence of a parallel conductor on microwave power line communication systems. For typical parameters, it is shown that the performance of these systems can be enhanced.

Interference on Power Line Communication (PLC), which is a wired communication technology that provides communication and data transmission over the existing electrical network, is examined in this paper. Many applications employ PLC technologies, which have the benefit of leveraging existing power connections for both power and data transfer, reducing cost and complexity. These interactions may be observed in contemporary smart grids and automobile power networks, where lengthy cables, switching power supplies, and communication links all work together but exacerbate electromagnetic interference problems. This research examines the effects of Spread Spectrum methods used to reduce EMI from power converters on PLC systems. Spread spectrum modulation and its three variants Sine, Random and Triangle are frequently employed to meet the requirements of electromagnetic compatibility, however there are some repercussions, that might be detrimental to the converter or the rest of the electrical network. These outcomes occur for various modulation algorithm settings and at various frequencies. Measurements are made utilising the Frame Error Rate value provided by the PLC link system to ascertain the interference produced by a SiC-based DC-DC converter in order to investigate these concerns and standardise an assessment approach.

The COVID-19 pandemic caused by SARS-COV-2 has infected over 500,000 people causing over 25,000 deaths in the last 10 weeks. A key host cellular protein required for the virus entry is angiotensin-converting enzyme 2 (ACE2). Recent studies have reported that patients with hypertension and diabetes treated with ACE inhibitors or angiotensin receptor blockers might be at a higher risk of COVID-19 infection as these drugs have been reported to increase ACE2 expression. This has raised the need to systematically investigate the effect of different drugs including antihypertensives on modulating ACE2 expression. Here, we analyzed a publicly available CMAP dataset of pre/post transcriptomic profiles for drug treatment in cell lines for over 20,000 small molecules. We show that only one subclass of antihypertensives drugs - ACE inhibitors, are significantly enriched for drugs up-regulating ACE2 expression. Studying the effects of the 672 clinically approved drugs in CMAP, we chart the drug categories that affect ACE2 expression. Specifically, we find that panobinostat (an HDAC inhibitor) confers the highest up-regulation of ACE2 expression while isotretinoin (a vitamin A derivative) is its strongest down-regulator. Our results provide initial candidates guiding further in vitro and in vivo studies aimed at assessing drug effects on ACE2 expression.

The geometry of Poincare disk itself is interpreted without any mapping to dierent spaces. Our approach might be one of the shortest and is intended for educational contribution.

In this paper, we consider a pursuit-evasion game of inertial players, where pursuer’s control is subject to integral constraint, and evader’s control is subject to geometric constraint. In the pursuit problem, the main tool is the strategy of parallel pursuit. Sufficient conditions are obtained for the solvability of pursuit-evasion problems. Also, the main lemma describing the monotonicity of an attainability domain of the evader is proved and an explicit analytical formula for this domain is given. As one of the important results of our paper, the Isaacs Life-line game is solved for a special case.

Criticism has been directed towards the traditional methods of management accounting employed by organizations thus far, as they fail to adequately address the growing need for competitiveness and sustainable development in a globalized environment. This criticism stems from both economic factors, such as insufficient monitoring of material, energy, and escalating overhead costs, and environmental concerns, where inadequate attention is given to vital information regarding significant environmental aspects, impacts, risks, and damages arising from the organization's activities and processes. Additionally, these methods do not sufficiently support the implementation of a functional environmental management system (EMS). Drawing upon our research in EMS standardization following the international standards ISO 1400X, as well as our knowledge gained during the development of the Slovak Technical Standard (STN) for ISO 14051, this paper presents an innovative model of environmental management accounting. This model is based on the cost accounting of material and energy flows within organizations. It serves as an enhancement framework for organizations with an existing EMS built according to the EN ISO 14001 model, as well as for organizations lacking a formalized EMS based on this standard. Within this paper, we specify, decompose, and apply the new model, focusing on the cost accounting of material-energy flows in a hypothetical organization. We meticulously examine the ten key steps of the model's structure, particularly in terms of costing and the allocation of costs to material, energy, system, and waste management.

Acute chemical ablation of lateral line hair cells is an important tool to understand lateral line-mediated behaviors in free-swimming fish larvae and adults. However, lateral line-mediated behaviors have not been described in fish larvae prior to swim bladder inflation, possibly because single doses of ototoxin do not effectively silence lateral line function at early developmental stages. To determine if ototoxins can effectively silence the lateral line during early development, we repeatedly expose zebrafish larvae to the ototoxin neomycin during a 36-hour period from 3-4 days post-fertilization (dpf). We use simultaneous transgenic and vital dye labeling of hair cells to compare 6- hour and 12-hour repeated treatment timelines and neomycin concentrations between 0–400 µM in terms of larval survival, hair cell death, regeneration, and functional recovery. Following exposure to neomycin, we find that the emergence of newly functional hair cells outpaces cellular regeneration, likely due to the maturation of ototoxin-resistant hair cells that survive treatment. Furthermore, hair cells of 4 dpf larvae exhibit faster recovery compared to 3 dpf larvae. Our data suggest that the rapid functional maturation of ototoxin-resistant hair cells limits the effectiveness of chemical-based methods to disrupt lateral line function. Furthermore, we show that repeated neomycin treatments can continually ablate lateral line hair cells between 3–4 dpf in larval zebrafish.

Background: The front-line treatment of advanced NeuroEndocrine Neoplasms (NENs) depends on clinical and pathological factors but there are no standard second-line therapies. Methods: Metastatic NENs patients were treated at the ENETS (European NeuroEndocrine Tumor Society) center of excellence of Naples (Italy), from 2014 to 2017 with second-line metronomic temozolomide, 75 mg/m2 per os “one week on/one week off”. Toxicity was graded with NCI-CTC criteria v4.0; objective responses with RECIST v1.1 and performance status (PS) according to ECOG. Results: Twenty-six consecutive patients were treated. Median age was 65.5 years. The predominant primary organs were pancreas and lung. Grading was G2 in 11 patients, G3 in 15. Eleven patients presented with PS 1 and 15 with PS 2. The median time-on-temozolomide therapy was 12.2 months (95% CI: 11.4-19.6). No G3/G4 toxicities were registered. Complete response was obtained in 1 patient, partial response in 4, stable disease in 19 (disease control rate: 92.3%), and progressive disease in 2. The median overall survival from temozolomide start was 28.3 months. PS improved in 73% of patients. Conclusions: Metronomic temozolomide is a safe and active treatment for G2 and G3 NENs. Prospective and larger trials are needed to confirm these results.

Atomic structure of N-electron atoms is often determined using the Hartree-Fock method, which is an integro-differential equation. The exchange term of the Hartree-Fock equations is usually treated as an inhomogeneous term of a differential equation, or with a local density approximation. This work uses matrix methods to solve for the Hartree-Fock equations, rather than the more commonly-used shooting method to integrate an inhomogeneous differential equation. It is well known that a derivative operator can be expressed as a matrix made of finite-difference coefficients; energy eigenvalues and eigenvectors can be obtained by using computer linear-algebra packages. We extend the same technique to integro-differential equations, where a discretized integral can be written as a sum in matrix form. This method is compared against experiment and standard atomic structure calculations. We also can use this method for free-electron wavefunctions. This technique is important for spectral line broadening in two ways: improving the atomic structure calculations, and improving the motion of the plasma electrons that collide with the atom.

Document deskewing is a fundamental problem in document image processing. While existing methods have limitations, such as Hough Line Transformation that can deskew images upside down, and Deep Learning models that require huge amounts of human labour and computational resources and still fail to deskew while taking care of orientation, OCR-based methods also struggle to read text when it is tilted. In this paper, we propose a novel, simple, cost-effective deep learning method for fixing the skew and orientation of documents. Our approach reduces the search space for the machine learning model to predict whether an image is upside down or not, avoiding the huge search space of predicting an angle between 0 and 360. We finetuned a MobileNetV2 model, which was pre-trained on imagenet, using only 200 images and achieve good results. This method is useful for automation-based tasks, such as data extraction using OCR technology, and can greatly reduce manual labour.

This research proposes a methodology for minimizing losses in transmission lines (LT), considering the reconfiguration of the architecture of the electrical power system (SEP). The implementation of this methodology redirects the power flow with optimal switching through its LTs to guarantee the stability of the voltage, angle, frequency, and power balance to minimize losses that affect the reliability and quality of the system. Optimal transmission switching (OTS) allows various types of analysis to be carried out, where the loadability of the lines, response times, and operating costs, among others, can be improved. This article proposes to minimize the losses in the transmission lines with the OTS by using AC power flows as a mixed integer nonlinear problem (MINLP). Several test scenarios evaluate the method’s effectiveness, determining the optimal topology for corrective control that optimizes power flows in different situations. It has been proven that this approach reduces losses compared to a base case by 99%, even in the face of N-1 or random contingencies, without losing load, maintaining the same active power dispatch, and finally verifying a strategic increase in dispatch of reactive power to maintain operating parameters within stable limits.

Fault detection in transmission lines plays a role in maintaining the dependability and steadiness of power networks. Traditional methods for identifying faults often struggle to handle the diverse nature of real world fault situations. Machine learning (ML) algorithms offer a data centered approach that can adjust and learn from datasets potentially overcoming the limitations of traditional approaches. This document presents a review of progress in using ML for detecting faults in transmission lines. By drawing insights from a variety of studies we explore how ML algorithms have evolved in fault detection, including techniques like networks, recurrent neural networks featuring Long Short Term Memory and convolutional neural networks. We delve into the spectrum of applications where ML is used for fault detection across fault scenarios and operational settings. Additionally we discuss the obstacles and prospects linked to putting ML based fault detection systems into practice such as challenges with data quality, model interpretability and integration with existing grid monitoring systems. Lastly we outline future research paths focused on pushing forward the boundaries of fault detection, in power transmission systems through approaches and collaborative endeavors involving academia, industry players and policymakers. In general, this review highlights how machine learning has the power to revolutionize fault detection methods enhancing the resilience and dependability of power systems.

In this study, we propose an efficient field-free line (FFL) generator for mechanically driven FFL-magnetic particle imaging (MPI) applications. The novel FFL generator comprises pairs of Halbach arrays and bar magnets. The proposed design generates high-gradient FFLs with low-mass permanent magnets, realizing fine spatial resolutions in MPI. We investigate the generated magnetic field using simulations and experiments. Our results show that the FFL generator yields a high gradient of 4.76 T/m at a cylindrical field of view of 30 mm diameter and a 70 mm open bore. A spatial resolution of less than 3.5 mm was obtained in the mechanically driven FFL-MPI.

Substrate integrated waveguides reduce the losses and increase the quality factor of resonators in communication filters when compared with traditional planar technologies, while maintaining their low cost and low profile characteristics. Empty substrate integrated waveguides go one step further, removing the dielectric of the substrate. One of these transmission lines is the empty substrate integrated coaxial line (ESICL), which adds the advantage of being a two conductor structure. Thus, it propagates a TEM mode, which reduces the dispersion and the bandwith limitation of other one conductor empty substrate integrated waveguides. Continuous profile filters, at the cost of being long structures, are very easy to manufacture and design (usually no optimization is needed), and they are highly insensitive to manufacturing tolerances. In this work a simple continuous profile filter, with a stop band response, is designed for the first time in the novel ESICL technology. The influence of the design parameters on the insertion losses and fractional bandwidth is discussed. A prototype has been successfully manufactured and measured. A sensitivity analysis shows the high tolerance of the proposed stop band filter to manufacturing errors.

: Cytokine storm is usually described as one of the main reasons behind COVID-associated mor-tality. Cytokines are essential protein molecules engaged in immune responses; they play a critical role in protection against infections. However, they also contribute to inflammatory reactions and tissue damage, becoming a double-edged sword in the context of COVID-19. Recent studies have suggested various cytokines and chemokines that play a crucial role in the immune response to SARS-CoV-2 infection. One such cytokine is Interleukin 27 (IL-27), which has been found to be elevated in the blood plasma of patients with COVID-19. Within this study, we will explore the role of IL-27 in immune responses and address our own findings concerning this cytokine in COVID-19. It affects a wide variety of immune cells; regardless of the pathological process it is involved in, IL-27 is critical for upholding the necessary balance between tissue damage and cytotoxicity against in-fectious agents and/or tumors. In COVID-19, it is involved in multiple processes, including antiviral cytotoxicity via CD8+ cells, IgG subclass switching, and even the activation of Tregs.

Density is a crucial parameter for quantitatively describing the physical properties of liquids. It serves as an important indicator for scientific research, production process control, pipeline transportation, and other aspects. In oil pipeline transportation and raw material processing, real-time online measurement of liquid density is of great significance. This paper analyzes the working principle of an on-line vibrating tube densitometer and derives the fitting equation for temperature, pressure, and density；it also conducts experiments with an on-line vibrating tube liquid densitometer and establishes a traceability chain for the experimental device. The experimental setup includes a desktop densitometer system, a multi-temperature field constant temperature stirring system, a walk-in constant temperature box, an automatic blowing system, and a frequency acquisition and calculation system. The uncertainty of the device's evaluation is U= 0.08kg/m3, k=2.The experimental research on the on-line vibrating tube liquid densitometer can be carried out within the range of (650~1400) kg/m3, (10~70)℃, (0~50)bar the metrological performance of the vibrating tube densitometer can be researched by utilizing the straight tube type and the elbow type on-line vibrating tube densitometer. A preliminary study was conducted on the effects of different densities, temperatures, and pressures on the vibrating tube system's vibration cycle. The fit coefficient and error were calculated, and the experimental results were compared to the theoretical analysis to confirm the device's conformity. The study verified the device's scientific and reasonable design, and demonstrated that it is feasible to use the device for follow-up research.

: Using line × tester analysis, the current research analyses parental genotypes and their combinations in normal conditions and identifies the genes influencing yield characteristics. In the present study, 15 diverse genotypes, including 10 lines, 5 testers, and 50 F1s hybrids, were evaluated for 13 morphological and 2 biochemical traits. A suitable location was taken to study the effect of 15 characters. The results exposed that ability mean squares were significant for all studied additive and non-additive components. In this direction, the general combining ability of PBW-343, DBW-39, K-402, K-1317, KRL-210, and K-68 were higher than the remaining parents. For morphological traits like yield, the top five crosses were described based on SCA effects, namely, HD-3086 × HD-3171, K-402 × K-9107, K-1317 × K-9107, HD-2967 × K-0307 and K-402 × K-68 in F1 generation. In addition, the high value of heritability was estimated for plant height (77.32%), spike length (32.26%), biological yield/plant (59.52%), and grain yield/plant (68.76%). However, the moderate values of heritability were estimated for days to maturity (22.78%) and phenol color reaction (18.00%). The higher genetic advance was not found for recorded characters; however, a moderate genetic advance was recorded for grain yield per plant (13.15%) and harvest index (11.72%). High heritability coupled with moderate genetic advance was recorded for two characters grain yield per plant and harvest index in F1 and F2 generations.

A new method of line shape calculations of hydrogen-like atoms in magnetized plasmas is presented. This algorithm makes it possible to solve two fundamental problems in the broadening theory: the analytical description of the radiation transition array between excited atomic states and account of a thermal ion motion effect on the line shapes formation. The solution to the first problem is based on the semiclassical approach to dipole matrix elements calculations and the usage of the specific symmetry properises of the Coulomb field. The second one is considered in terms of the kinetic treatment of the frequency fluctuation model (FFM). As the result one has a universal description of line shapes under the action of the dynamic of ion’s microfield. The final line shape is obtained by the convolution of the ionic line shape with the Voigt electron-Doppler profile. The method is applicable formally for large values of principle quantum numbers. However, it is demonstrated the efficiency of the results even for well known first members of the hydrogen Balmer series Dalpha and Dbeta. The comparison of obtained results with accurate quantum calculations is presented. The new method may be of interest for investigations of spectral line shapes of hydrogen-like ions presented in different kinds of hot ionized environments with the presence of a magnetic field, including SoL and divertor tokamak plasmas.

The wide range of applications of nanoparticles (NPs) has increased the probability of environmental and occupational exposure. In a previous comparative study on cell line A549, we observed that oxidative stress caused by Co₃O₄ NPs affects the energetic homeostasis and the detoxification capacity, preventing autophagy induced by TiO₂ NPs. In this study, we have investigated the effects of NPs on the cell cycle.Cytofluorimetric analysis showed a slow-down of the cell cycle progression for both NPs, with increases in the percentage of resting cells in the G0/G1. These observations were confirmed by a reduced expression of all cyclins, especially of CCNE1 and CDK2, involved in the late stages of the G1 phase, coupled with a significant increase in the expression of p21 only for Co₃O₄ NP exposure. On the contrary, the effects of TiO₂ NPs were modest. Cell cycle related miRNA-34a, miRNA-126 and miRNA-1290 resulted increased at different early time-points (4-8h) but were down-expressed at 24h-48h only after TiO₂ NP exposure. Our results show that NPs have an antiproliferative effect and deregulate cell cycle on A549 cells. These effects should not be underestimated because regulation of cycle progression is crucial for cell survival and repair of genetic damage.

A bread wheat line (N11) and a disomic 2D(2R) substitution triticale line have been crossed and backrossed four times. At each step electrophoretic selection for the seeds that possessed, simultaneously, the complete set of high molecular weight glutenin subunits of N11 and the two high molecular weight secalins of rye, present in the 2D(2R) line, was carried out. Molecular cytogenetic analyses of the BC4F5 generation have revealed that the selection carried out had produced a disomic addition line (2n=44). The pair of additional chromosomes consisted of the long arm of chromosome 1R (1RL) from rye fused with the satellite body of the wheat chromosome 6B. Rheological analyses revealed that the dough obtained by the new addition line had higher quality characteristics when compared with the two parents. The role of the two additional high molecular weight secalins, present in the disomic addition line, in influencing improved dough characteristics is discussed.

This paper presents the methodology to detect and identify the type of fault that occurs in shunt connected static synchronous compensator (STATCOM) transmission line using a combination of Discrete Wavelet Transform (DWT) and Naive Bayes classifier. To study this, the network model is designed using Mat-lab/Simulink. The different faults such as Line to Ground (LG), Line to Line (LL), Double Line to Ground (LLG) and three-phase (LLLG) fault are applied at different zones of system with and without STATCOM considering the effect of varying fault resistance. The three-phase fault current waveforms obtained are decomposed into several levels using daubechies mother wavelet of db4 to extract the features such as standard deviation and Energy values. The extracted features are used to train the classifiers such as Multi-Layer Perceptron Neural Network (MLP), Bayes and Naive Bayes (NB) classifier to classify the type of fault that occurs in the system. The results reveal that the proposed NB classifier outperforms in terms of accuracy rate, misclassification rate, kappa statistics, mean absolute error (MAE), root mean square error (RMSE), relative absolute error (RAE) and root-relative square error (RRSE) than MLP and Bayes classifier.

Extramammary Paget disease (EMPD) is an uncommon adenocarcinoma of apocrine gland-rich areas, presenting significant diagnostic challenges due to its nonspecific clinical appearance and frequent misidentification as benign, inflammatory skin conditions. Traditional diagnostic methods such as biopsy are invasive and uncomfortable, often required repeatedly due to high recurrence rates. Dermoscopy and non-invasive imaging techniques have been used but provide limited diagnostic accuracy due to their constraints in depth penetration and resolution. Recent advancements in imaging technologies, such as line-field confocal optical coherence tomography (LC-OCT), show promise in enhancing diagnostic precision while minimizing invasive procedures. LC-OCT merges high-resolution imaging with deep penetration capabilities, capturing detailed horizontal and vertical skin images akin to histopathology. This study evaluated the diagnostic performance of LC-OCT in detecting EMPD and its recurrence in 17 clinically suspicious anogenital regions, belonging to 6 patients. Data were collected prospectively at patient bedside by an LC-OCT expert with poor training for EMPD; and, then, reviewed retrospectively by an independent LC-OCT expert with adequate training for EMPD and no concerns about time. The prospective examination yielded 64.7%-accuracy, 71.4%-sensitivity, and 33.3%-specificity. The retrospective analysis achieved 94.1%-accuracy, 100%-sensitivity, and 66.7%-specificity, with the only false positive case being a difficult-to-diagnose concomitant presentation of a lichen sclerosus et atrophicus. Despite the need for specialized training, our results suggest that LC-OCT represents a valuable tool for accurately identifying EMPD and improve its management by reducing unnecessary biopsies. Further studies are needed to standardize its clinical application.

Pea (Pisum sativum L.), like most legumes, forms mutualistic symbioses with nodule bacteria and arbuscular mycorrhizal (AM) fungi. The positive effect of inoculation is partially determined by the plant genotype, thus, pea varieties with high and low symbiotic responsivity have been described, but the molecular genetic basis of this trait remains unknown. Here, we compare the symbiotically responsive breeding line ‘Triumph’ of grain pea with its parental cultivars ‘Vendevil’ (a donor of high symbiotic responsivity) and ‘Classic’ (a donor of agriculturally valuable traits) using genome and transcriptome sequencing. We show that ‘Triumph’ inherited one-fourth of its genome from ‘Vendevil’, including the genes related to AM and nodule formation, and reveal that under combined inoculation with nodule bacteria and AM fungi, ‘Triumph’ and ‘Vendevil’, in contrast to ‘Classic’, demonstrate similar up-regulation of the genes related to solute transport, hormonal regulation and flavonoid biosynthesis in their roots. We also identify the gene PsGLP2, whose expression pattern distinguishing ‘Triumph’ and ‘Vendevil’ from ‘Classic’ correlates with difference within the promoter region sequence, making it a promising marker for the symbiotic responsivity trait. The results of the study may be helpful for future molecular breeding programs aimed at creation of symbiotically responsive cultivars of pea.

In this paper, a study was conducted on the Ramsey interference and spectral line locking techniques based on rubidium-87 cold atoms. Using sequential control technique, the timing design of a three-dimensional magneto-optical trap (MOT), cold atoms’ free fall, Ramsey microwave interference, and two-level fluorescence detection was realized, achieving the state preparation of cold atoms and clock transitions. By designing an automatic peak-finding algorithm, numerical integration was performed on the time-of-flying (TOF) signal, and narrow linewidth cold atom Ramsey interference fringes were obtained. Based on this, a frequency-hopping method was used to lock the frequency of the 10MHz oven-controlled crystal oscillator (OCXO) in a closed loop, achieving a linewidth of 38Hz. This preliminary result verifies the feasibility of the system design.

This study is designed to assess and improve apparel sewing section efficiency and productivity throughout line balancing. Apparel industry is one of the oldest and among the most global industry, being primarily concerned with the design and production of cloth and their supply. The central process in apparel manufacturing is the joining together of components which is known as the sewing process , which is the most labour intensive type of manufacturing process .Proper utilization of resources in garment sewing section is more critical to enhance the performance of the apparel industry by reducing production cost and minimizing wastage. For effective utilization of resources in the sewing section, good line balancing is important to increase productivity and production efficiency. This research was a design to analyse and improve the assembling line in the case of Telaje garment manufacturing and sales plc. The study was first conduct observations in the production floor and start work with the selection of sewing line in the garment production process. Among the nine lines of the factory select one on the production floor and one garment ordered product known as five pocket men’s jeans trousers are selected. For this study, both qualitative and quantitative research approaches were employed. Both primary and secondary data sources are used to detail the collected relevant data to understand the current efficiency scenario of the factory. The main challenges to minimizing line efficiency and productivity with the expected performance measurement are improper utilization of resources and improper implementation of line balancing in sewing section, therefore this thesis work shows that the bottleneck process and consequence solution will be searched, and finally significantly improving the productivity by 418 unit products/ day and, hence the efficiency will increase from 28.83% to 50.04% of the line

More than 800 million tons of fish are utilizing in a year and 25-30% become waste. The waste amount is beneficial source for extraction of collagen. But procedure of extraction is still to be optimized. The current study was designed to extract collagen from fish through fish waste fermentation under various conditions. For collagen extraction we did lactic acid fermentation in which yogurt and Dough bacteria was added with fish sample and placed it in incubator at 30ºC for one month. In yogurt and dough culture have at least 10 type of lactic acid bacterial species. After every week we check PH of each sample and take soup of that sample. After centrifugation of that sample’s TCA (Trichloroacetic acid) precipitation was done of yogurt and dough sample and kept at -20ºC. then did SDS-PAGE) using 6% resolving and 5% stacking gel of already stored sample. Then HaCaT cells (1 × 10⁴ cells/well) were cultured in 96-well flat-bottom culture plates and treated with appropriate doses of FFCP (fermented fish collagen peptide) for 24 and 48 hours.The SDS-PAGE revealed that the collagen protein of fish had doublet pattern for α1 and α2 chains at corresponding to 145 kDa and 132 kDa respectively. The density for α1 twice as compared to α2. Our result agrees that The fish collagen consists mostly of α-chain as well as little amount of inter and intra molecular cross-linked components of α-chains; b (dimmer) and c (trimer). Different biochemical tests were done for identification of lactic acid bacteria catalase positive, citrate positive, urease negative. Our fermented fish collagen and peptides mixture were test for cellular cytotoxicity and proliferative effect on HaCaT cells. Current result shows that fermented extracted collagen are nontoxic and induce the proliferation of HaCaT cells. Current study is supported by various studies that revealed the medical application of fish extracted collagen as underline.

In volleyball, the jump serve is a fundamental and crucial skill that is one of the most commonly used serving techniques. This study aimed to examine the kinematic differences between straight line (SL) and diagonal line (DL) in volleyball jump serves by focusing on torso and attack arm joint motions. Three-dimensional coordinate data were captured using a motion capture system (200 Hz) in 14 right-handed male professional volleyball players who performed SL and DL jump serves. This result suggests that the pelvis and torso backward rotation angles during the arm-clocking phase were smaller when performing DL serves. During ball contact, the servers exhibited greater forward rotation angles of the pelvis and torso to control the upper body facing the diagonal direction of the target zone. In addition, lowering the forward tilt angle of the trunk helped the servers maintain body balance in the air and increased their wrist flexion angle, preventing the ball from flying out of bounds when performing DL. These findings highlight the importance of controlling pelvic and torso rotations in the transverse plane when adjusting for different serving lines. These insights can guide volleyball athletes and coaches in refining their serving techniques.

Microglial dysfunction is one of the hallmarks and leading causes of common neurodegenerative diseases (NDD), including Alzheimer’s disease (AD) and Parkinson’s disease (PD). All these pathologies are characterized by aberrant aggregation of disease-causing proteins in the brain, which can directly activate microglia, trigger microglia-mediated neuroinflammation, and increase oxidative stress. Inhibition of glial activation may represent a therapeutic target to alleviate neurodegeneration. Recently, 3-iodothyronamine (T1AM), an endogenous derivative of thyroid hormone (TH) able to interact directly with a specific GPCR known as trace amine-associated receptor 1 (TAAR1), gained interest for its ability to promote neuroprotection in several models. Nevertheless, T1AM’s effects on microglial disfunction remain still elusive. In the present work we investigated whether T1AM could inhibit the inflammatory response of human HMC3 microglial cells to LPS/TNFα or β-amyloid peptide 25-35 (Aβ25-35) stimuli. The results of ELISA and qPCR assays revealed that T1AM was able to reduce microglia-mediate inflammatory response by inhibiting the release of proinflammatory factors, including IL-6, TNFα, NF-kB, MCP1 and MIP1, while promoting the release of anti-inflammatory mediators, such as IL-10. Notably, T1AM anti-inflammatory action in HMC3 cells resulted to be a TAAR1-mediated response, further increasing the relevance of the T1AM/TAAR1 system in the management of NDD.

Most quantum gravity theories endow space-time with a discreet nature by space quantization on the order of Planck length (lp ). This discreetness could be demonstrated by confirmation of Lorentz invariance violations (LIV) manifested at length scales proportional to lp. In this paper, space-time line elements compatible with the uncertainty principle are calculated for a homogeneous, isotropic expanding Universe represented by the Friedmann-Lemaitre-Robertson-Walker solution to General Relativity (FLRW or FRW metric). To achieve this, the covariant geometric uncertainty principle (GeUP) is applied as a constraint over geodesics in FRW geometries. A generic expression for the quadratic proper space-time line element is derived, proportional to Planck length-squared and dependent on two contributions. The first is associated to the energy-time uncertainty, and the second depends on the Hubble function. The results are in agreement with space-time quantization on the expected length orders, according to quantum gravity theories and experimental constraints on LIV.

Maize varieties with high amylose proportion are more valuable for starch industry. The SBEⅡb gene encodes one of the starch branching isozymes (SBEⅠ, SBEⅡa, and SBEⅡb). Its recessive mutant amylose-extender (ae/sbe2b) decreases the total activities of SBEs and increases amylose proportion up to 60%. Here, the breeding potential of introduced germplasm line GEMS-0067 was evaluated by genotyping and phenotyping. The deletion of the ninth exon of the SBEⅡb gene, high amylose proportion, and the typical irregular granules suggested that this germplasm line was derived from the same resource of high amylose line AE11. The gelatinization and thermal properties, and degree of polymerization of starch chain showed its advantages used for high amylose breeding. However, the negative correlation between amylose proportion and starch content, as well as ker-nel filling characteristics should be overcome during breeding process.