Heat pumps are increasingly becoming a key solution in the quest for decarbonization, offering a significant advantage over traditional boilers due to their superior energy efficiency. Not only can heat pumps provide both heating and cooling, but they also achieve thermal efficiencies exceeding 500%, which can seem to defy conventional expectations. The outdoor unit of a heat pump consists of about twenty main components, one of which is a complex network of copper pipes and sheets welded to valves, connectors, and other fittings. This set involves over thirty welded joints, highlighting a significant opportunity for reducing manufacturing time through process optimization. Copper is a critical material extensively used in various applications due to its excellent thermal and electrical conductivity. However, these very properties make welding copper particularly challenging, especially when aiming to automate and streamline industrial processes. Traditionally, connecting copper pipes and fittings is done through brazing, yet, alternative methods such as LASER welding, electron beam welding, resistance welding, friction welding, and ultrasonic welding also exist. This study focuses on the ultrasonic welding of copper, aiming to identify the optimal parameters that maximize the mechanical strength of overlapping joints and ensure effective tube sealing. Experimental results showed that for copper sheets, the best outcomes were achieved with a welding time of 3 s and a pressure of 6 bar. For tube sealing, the optimal conditions were a welding time of 3 s and a pressure of 4 bar. For both scenarios, the same variables were used, retention time of 0.62 s, initial pressure of 2 bar, retention pressure of 2 bar and sonotrode rising pressure of 3 bar. The analysis reveals that ultrasonic welding of copper can achieve both robust mechanical strength and reliable sealing, making it a promising technique for industrial applications.

The new unique technology for granulation of metals and nonmetallic melts is presented in the paper. It was created on the newly developed controlled film flow disintegration with rapid cooling of the droplets and solidified granules in amorphous state. Three new phenomena discovered by us created the base for 3 different methods for granulation of metals and nonmetallic melts in a wide range of granules’ sizes. Electromagnetic resonance method allows producing granules of metals in the range of 1 mm and over. The soliton-like vibrational regime is available for production of any granulation material in the range 0.1-1 mm. Moreover, the shockwave regime is applicable for producing particles from 10 micrometers by size. All methods produce particles of the stated size with a narrow distribution by size: deviation from the average size no more than 50%. The other known methods do not produce granules with such high cooling rate, which can realize the amorphous state and cannot regulate size of particles in such bright but narrow range from 10 micrometers to 1-2 mm.

This study explores the use of remote ultrasound vibration to enhance welding strength. It examines the effects of 20 kHz, and 40 kHz High Power Ultrasound Transducers (HPUT) in contact and contactless modes during ultrasonic assistance laser welding. Employing shear tests and microscopy for assessment, the research evaluates ultrasound's impact on welding strength and identifies the optimal transducer. Theoretical and numerical analyses investigate vibration transmission into the welding area, particularly examining the vibration distribution and cavitation initiation within the molten pool area. Results indicate that ultrasound-assisted welding increases pull test performance, including the resistance force and strain, and improves microscopic structural integrity. Numerical simulations suggest that narrow-band vibration intensifies pressure in specific welding zones. Contactless ultrasound application also shows enhanced welding quality, offering a promising alternative to current methods. This work contributes to electric car technology by suggesting improvements in welding techniques for power battery systems.

The demand for efficient processes through a comprehensive understanding and optimization of welding conditions continues to grow in the manufacturing industry. This study involves heat-resistant 2.25 Cr-1 Mo V-groove steel welding using the square-waveform alternating cur-rent. Experiments were conducted to build the relationship between input variables—such as current, frequency, electrode negativity ratio, and welding speed—and process performance, such as penetration, bay area, deposition rate, melting efficiency, percentage dilution, flux–wire ratio, and heat input. The process was analyzed in light of the defect-free high-deposition weld groove weld, the sensitivity to process parameters, and the optimization and development of the process map. The study proposes an innovative approach to reducing the cost and time of optimizing the one-pass-each-layer V-groove welding process using bead-on-plate welds. Square waveform welding creates a metallurgical notch in the form of a bay at the fusion boundary that can be minimized by selecting appropriate welding conditions. The square waveform submerged arc welding is more sensitive towards changes in current and welding speed than the frequency and electrode negativity ratio; however, the electrode negativity ratio and frequency are minor but helpful parameters to achieve optimal results. The proximity of the planned and experimental results to within 3% confirms the validity of the proposed approach. The investigation shows that 90% of the maximum deposition rate is possible for one-pass-each-layer V-groove welds within heat input and weld width constraints.

This investigation aims to discuss the formation process of eddies and the heat transportation in plasma keyhole arc welding. In order to clarify this issue, the measurement of the convection inside the weld pool, the convection on the weld pool surface, also the temperature distribution on the weld pool surface were carried out. The results showed that two eddies were found in the weld pool, which is controlled mainly through the shear force by the plasma flow acting on the weld pool surface. The magnitude, extent and direction of the shear force are thought to be determined primarily by the variation of keyhole profile. The relative shape and strength of each eddy is largely changed depending on the change of the keyhole profile when nozzle diameter changed. These relative strengths of each eddy are considered to decisively govern the heat transport in the weld pool coinciding with the direction of eddies. A larger eddy near the lower part of the keyhole inside the weld pool was found out in the case of 1.6 mm, meanwhile a upward larger eddy was found out near the upper part of the keyhole inside the weld pool in the case of 2.4 mm.

A central hypothesis on brain functioning is that plasticity regulates the signals transfer function by modifying the efficacy of synaptic transmission. In the cerebellum, granular layer has been shown to control the gain of signals transmitted through the mossy fiber pathway. Until now, the impact of plasticity on incoming activity patterns was analyzed by combining electrophysiological recordings in acute cerebellar slices and computational modeling, unraveling a broad spectrum of different forms of synaptic plasticity in the granular layer, often along with forms of intrinsic excitability changes. Here, we attempt to provide a brief overview of the most prominent forms of plasticity at excitatory synapses formed by mossy fibers onto principal neurons (granule cells, Golgi cells and unipolar brush cells) in the granular layer. Specifically, we will highlight current understanding of the mechanisms and their functional implications of the synaptic and intrinsic plasticity, providing valuable insights into how inputs are processed and reconfigured at the cerebellar input stage.

Among all the processing technologies of heat-treatable aluminum alloys like 2219 aluminum alloy, using friction stir welding (FSW) as the joining technology and using electromagnetic forming (EMF) for plastic forming technology both have obvious advantages and successful applications. Therefore, there is a broad prospect for the compound technologies which can be used on the 2219 aluminum alloy to manufacture the large-scale thin-wall parts in the astronautic industry. The microstructure and mechanical properties of 2219 aluminum alloy under the process compounded of FSW, heat treatment, and EMF were investigated by means of tensile test, optical microscope (OM), and scanning electron microscope (SEM). The results show that the reduction of strength, which was caused during the FSW process, can be recovered effectively by the post-welding heat treatment composed of solid solution and aging, while the ductility was still reduced after heat treatment. Under the compound technology of FSW, heat treatment, and EMF, the forming limit of 2219 aluminum alloy decreased distinctly due to the poor ductility of the welding joint. A ribbon-pattern, which was formed due to the banded structure caused by FSW process, was found on the fracture surface of welded 2219 aluminum alloy after EMF treatment. During the EMF process, because of the effects of induced eddy current, a unique structure, which was manifested as a molted-surface appearance under the SEM observation, was formed as the material fractured.

This paper introduces a new adaptation of the enthalpic lattice Boltzmann method (LBM) tailored to simulate the intricate dynamics of conjugate heat transfer in non-homogeneous media, showcasing considerable potential for enhancing heat exchanger designs. This approach expands upon the conventional enthalpic LBM framework by seamlessly incorporating tailored source terms, enabling precise representation of local and transient variations in the medium’s thermophysical properties. The resulting LBM model comprehensively captures the energy conservation equation, with exceptions made only for flow compressibility and viscous dissipation, thereby significantly augmenting its versatility in analyzing heat exchanger configurations. Verification tests, comprising assessments of both transient and steady-state solutions, unequivocally validate the accuracy of the proposed model, further bolstering its reliability for analyzing heat exchange processes within intricate heat exchanger geometries. To demonstrate its efficacy, simulations of conjugate heat transfer processes involving fluid natural convection within structured cavities were performed, imposing both Dirichlet and Neumann boundary conditions to emulate scenarios encountered in practical heat exchanger operations. The findings yield compelling insights, particularly in the transient regime, revealing the beneficial impact of structured cavities on enhancing heat transfer processes. These insights inform potential design optimizations for heat exchangers. The results emphasize the potential of the modified enthalpic LBM approach to elucidate complex heat transfer phenomena in non-homogeneous media and structured geometries, offering valuable implications for heat exchanger engineering and optimization.

The design complexity of the new generation of civil aero-engines results in higher demands on engines’ components, higher component temperature, higher heat generation, and, finally, critical thermal management issues. This paper will propose a methodological approach to create physics-based models for heat loads developed by sources as well as a systematic sensitivity analysis to identify the effects of design parameters on the thermal behaviour of civil aero-engines. The ranges and levels of heat loads generated by heat sources (e.g., accessory gearbox, bearing, pumps, etc.) and heat absorption capacity of heat sinks (e.g., engine fuel, oil, and air) are discussed systematically. The practical research challenges for thermal management system design and development for the new and next generation of turbofan engines will then be addressed through a sensitivity analysis of the heat load values as well as the heat sinks flow rates. The potential solutions for thermal performance enhancements of propulsion systems will be proposed and discussed accordingly.

This article presents a new input device for spastic patients and others with similar symptoms. The sensor consists of a disc used to determine positions and can replace standard joysticks in medical devices such as electric-powered wheelchairs. Using a standard joystick while operating a powered wheelchair can result in dangerous situations when spastic movements occur and extremities cramp making them uncontrollable. To avoid this, a disc was developed that can be controlled with any body part. By shifting weight (x- and y-axis) the disc can tilt in any direction creating a proportional output signal and can also be pushed down in the center (z-axis) to open a menu on a screen for example. When spasms occur it is impossible for users to get stuck on the input device because the disc is flat and can be mounted within a control panel. Body parts coming into contact with the disc would merely slide across the disc without triggering unintentional actions. The sensor presented here is also adaptive and can be adjusted to fit a user’s strength and range of motion. This proposal aims to develop an input device that enables spastic patients to operate sensitive systems safely.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

In this article, a novel hybrid welding process called plasma-TIG coupled arc welding was proposed to improve the efficiency and quality of welding by utilizing the full advantage of plasma and TIG welding processes. The two arcs of plasma and TIG were pulled into each other into one coupled arc under the effect of Lorentz force and plasma flow force during welding experiments. The arc behavior of coupled arc was studied by means of it’s arc profile, arc pressure and arc force conditions. The coupled arc pressure distribution measurements were performed. The effects of welding conditions on coupled arc pressure were evaluated and the maximum coupled arc pressure was improved compared with single-plasma arc and single-TIG arc. It was found that the maximum arc pressure was mainly determined by plasma arc current and plasma gas flow. According to the results, the proposed coupled arc welding process have both advantages of plasma arc and TIG method, and it has a broad application prospect.

A power factor correction (PFC) rectifier is compulsory for any electronic circuitry connected to the electrical grid. The majority of PFCs that are utilized are based on a step-up converter that supplies high DC voltage at its output terminal. Electric vehicle battery voltage varies from a few hundred to almost a thousand volts. Thus, an additional conversion step is obligatory when designing an all-brand universal charger. This paper presents a new type of front-end versatile step up / down three voltage level PFC. The rectifier can operate in continuous conduction mode or discontinuous conduction mode. First, the rectifier’s principle of operation is described, and then an innovative rectifier is analyzed for continuous and discontinuous conduction modes. Finally, the proposed theory is experimentally validated in a multiplier-less dual loop mode at discontinuous conduction modes. It was shown that although there is no multiplier use in the control circuitry, the power factor is near unity. It was revealed that the rectifier could swing the output voltage from 50 V to 900 V while the input voltage was 230 Vrms. The innovative topology suits any standard PFC rectifier, three-level voltage supplement, and dual-stage low-voltage power supply.

The CMT (Cold Metal Transfer) arc welding process is a convenient instrument for the assembly of thin sheets [1], [2]. More particularly, it permits the decrease of the amount of heat transferred to the parts to-be assembled, thus reducing their subsequent deformations. The present work aims at simulating the CMT welding of thin stainless-steel sheets in order to develop an approach that allows the prediction of temperature fields, as well as final deformations induced by the welding process. For that purpose, instrumented tests and numerical simulations were set aiming at comparing the experiments with simulations. Butt-welding of stainless-steel sheets was considered, with a thickness ranging from 1 to 1.2 mm. The weld seam samples were observed in order to set an equivalent heat source for each configuration. Moreover, the electric current and voltage were surveyed, and temperature measurements were performed using K-type thermocouples. In addition, displacement measurements were obtained using the DIC (Digital Image Correlation) technique. Thermomechanical simulations were then carried out using an equivalent heat source approach, considering the phase changes of elements, i.e. the transitions from solid to liquid and from liquid to solid. These simulations also consider the actual geometry of seams induced by addition of a filler material.

Induction heating is a fast, reproducible, and efficient heating method used in various manufacturing processes. However, there is no established additive manufacturing (AM) process based on induction heating using wire as feedstock. This study investigates a novel approach to AM based on inductive heating, where a steel wire is melted and droplets are detached periodically using a two-winding induction coil. The process parameters and energy input into the droplets are characterized. The induction generator exhibits sluggish response to the excitation voltage, resulting in a lag in the coil current. The process is captured using a high-speed camera, revealing regular droplet formation and uniform size and shape when operated within an appropriate process window. Larger drops and increased spatter formation occur outside this window. The proposed method allows for the production of droplets with almost spherical shapes. Further analysis and characterization of droplet formation and energy input provide insights into process optimization and overall efficiency.

The objective of this work is to analyze the improvement of heat transfer in trapezoidal fin heat exchangers using numerical simulation. Heat exchangers are essential components frequently used in contemporary electronic gadgets to effectively disperse heat produced by high-power components. Nevertheless, as electronic devices continue to advance and become more powerful, the heat transfer capacity of heat exchangers is facing more requirements, therefore requiring enhanced heat dissipation efficiency. Afterwards, various fin angles were adjusted, and the heat transmission efficiency was compared. Modifying the angles can significantly improve the effi-ciency of convective heat dissipation. Moreover, it has been found that employing an optimized trapezoidal fin structure can further enhance the efficiency of heat transfer. The results indicate that trapezoidal fin heat exchangers provide superior heat dissipation efficiency compared to conventional heat exchangers. This is important for enhancing the thermal dissipation capabili-ties of electrical gadgets, hence guaranteeing steady functionality and extending their longevity. Subsequent study might explore supplementary methods to boost heat transmission in different heat exchanger configurations in order to meet the growing requirements for heat dissipation.

Input reconstruction problem is usually encountered in the areas such as virtual sensing, image restoration, sensor linearization, and communications. The input reconstruction problem can be seen as an inverse problem. Given a nominal system, two types of approaches are commonly used for solving the inverse problem. The first one is to directly invert the nominal system, and the second one is to derive an inversion of the nominal system in an indirect way. However, for the first type of approaches, system inversion cannot be directly conducted under some conditions such as there exist nonminimum-phase zeros in the nominal system, while for the second type of approaches, simultaneously guaranteeing stability and causality of the obtained inversion is still not solved well. In order to avoid the drawbacks existing in the two types of approaches, an alternative approach is proposed for input reconstruction. In this approach, the input signal is first modeled as the output of a state-space model, afterwards two Kalman filters for the model resulted by combining the input signal model and the nominal system model are implemented alternatively such that the input signal can be sequentially reconstructed in an infinite horizon. The proposed input reconstruction approach is applied in two examples, and simulation results can illustrate the effectiveness of the proposed approach.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

This study explores the stability of electrodeposited copper catalysts utilized in electrochemical CO2 reduction (ECR) across various amine media. The focus is on understanding the influence of different amine types, corrosion ramifications, and the efficacy of pulse ECR methodologies. Employing a suite of electrochemical techniques including potentiodynamic polarization, linear resistance polarization, cyclic voltammetry, and chronopotentiometry, the investigation reveals useful insights. The findings show that among the tested amines, CO2-rich monoethanolamine (MEA) exhibits the highest corrosion rate. However, in most cases the rates remain within tolerable limits for ECR operations. Primary amines, notably monoethanolamine (MEA), show enhanced compatibility with ECR processes, attributable to their resistance against carbonate salt precipitation and sustained stability in potential over extended durations. Conversely, tertiary amines such as methyldiethanolamine (MDEA) present challenges due to the formation of carbonate salts during ECR, impeding their effective utilization. The study highlights the effectiveness of pulse ECR strategies in stabilizing ECR. A noticeable shift in cathodic potential and reduced deposit formation on the catalyst surface through periodic oxidation underscores the efficacy of such strategies. These findings offer insights for optimizing ECR in amine media, thereby providing promising pathways for advancements in CO2 emission reduction technologies.

Welding processes offer a unique capability with a wide range of applications in industries. In recent times, welding has established itself as a tool for large scale additive manufacturing. In general, the quality and repeatability assurance for welding and specifically for additive manufacturing necessitates integrating process monitoring techniques with existing welding and additive manufacturing processes. The process-specific signals such as welding current fluctuations, temperature, and acoustic, generated during the welding operations, make them a suitable candidate for digitization. This chapter comprehensively describes the process monitoring techniques relevant to welding and additive manufacturing. Firstly, various sensors used during welding are described for their construction and working. Subsequently, specific applications of the sensors in digitizing the welding processes are presented.

This study aimed to investigate the fatigue performance and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar lap joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Furthermore, the fatigue life of the 14 kV joints was one order of magnitude higher compared to the 12 kV joints. SEM observation of the fatigue fracture surface revealed the presence of typical "tire-mark" fatigue striations only in the 14 kV joint, indicating higher ductility and the ability to withstand extended plastic deformation. Notably, ultra-fine nanocrystalline Al2Cu phase, amorphous phase, and numerous dislocations hindered EBSD acquisition in the transition zone. Nevertheless, dense low-angle grain boundaries (LAGBs) and refined grains were examined at the bonding interface. This suggests that the high-velocity collision caused severe plastic deformation and led to the formation of substructures. The interfacial strength was attributed not only to the "wave-like" or "inverted hook-like" diffusion layer but also to the presence of refined grains along the interface and nanocrystalline Al2Cu in the transition zone. Furthermore, the hybrid nanocrystalline-amorphous microstructure strengthened the joint by regulating the balance between strength and ductility.

In this investigation steel P355NH has been successfully cladded with Inconel 625 through the method of explosive welding. Explosively welded bimetal clad-plate was subjected to the two separated post weld heat treatment processes: stress relief annealing (at 620oC for 90 minutes) and normalizing (at 910oC for 30 minutes). In order to analyze the microstructure of the joint in the as-welded state and to investigate the influence of the post weld heat treatment on it, the light and scanning electron microscope observations and microhardness analysis have been performed. The examination of the diffusion zone microstructure has been performed by using the scanning transmission electron microscope. It was stated that obtained joint has characteristic wavy-shape geometry with the presence of the melted zones and severe deformed grains of both joined materials. Strain hardening of the materials in joint zone was established with microhardness analysis. In both of the heat treatments the changes in the grain structure have been observed. The normalizing heat treatment has the most significant impact on the microstructure of the joint as well as the concentration of the chemical elements in the joint zone. It was reported that due to normalizing the diffusion zone has been formed together with precipitates in the joint zone. The analysis of the diffusion zone images leads to the conclusion that the diffusion of alloying elements from Inconel 625 to steel P355NH takes place along the grain boundaries with additional formation of the voids in this area. The precipitates in Inconel 625 in the joint zone are two type of carbides – chromium-rich and molybdenum-rich. Scanning transmission electron microscope observation of the grain microstructure in the diffusion zone shows that this area consists of equiaxed grains (from the side of Inconel 625 alloy) and columnar grains (from the side of steel P355NH).

The material flow dynamic and velocity distribution on the melted domain surface play a crucial role on the joint quality and formation of welding defects. In this study, authors investigated the effects of the low and high currents of plasma arc welding on the material flow and thermodynamics of molten pool and its relationship to the welding defects. The high-speed video camera (HSVC) was used to observe the convection of the melted domain and welded-joint appearance. Furthermore, to consider the Marangoni force activation, the temperature on the melted domain was measured by a thermal HSVC. The results revealed that the velocity distribution on the weld surface was higher than that inside the molten weld pool due to the difference of the massive density between the air and the steel. Moreover, in the case of low welding current (80A) the convection speed of molten was faster than that of the high welding current case (160A) owing to the difference of main driving forces direction and strength, which leading to undercut and humping defects on the weld surface and excessive convex (burn-through) defect at the bottom weld side, respectively. The medium welding current (120A) had two convection patterns with the main flow in backward direction, which resulted in better welding quality without defect. The interaction between the shear force and Marangoni force played a solid state on the convection and heat transportation processes in the plasma arc welding process.

This study employs the reflection symmetry decomposition (RSD) method to extract polarization scattering features from ground object images, aiming to determine the optimal data input scheme for deep learning networks in polarimetric synthetic aperture radar classification. Eight distinct polarizing feature combinations are designed, and the classification accuracy of various approaches is evaluated using the classic convolutional neural networks(CNNs) AlexNet and VGG16. The findings reveal that the commonly employed 6-parameter input scheme, favored by many researchers, lacks the comprehensive utilization of polarization information and warrants attention. Intriguingly, leveraging the complete 9-parameter input scheme based on the polarization coherence matrix results in improved classification accuracy. Furthermore, the input scheme incorporating all 21 parameters from the RSD and polarization coherence matrix notably enhances overall accuracy and the Kappa coefficient compared to the other 7 schemes. This comprehensive approach maximizes the utilization of polarization scattering information from ground objects, emerging as the most effective CNN input data scheme in this study. Additionally, the classification performance using the second and third component total power values (P2 and P3) from the RSD surpasses the approach utilizing surface scattering power value (PS) and secondary scattering power value (PD) from the same decomposition.

Enhancing energy efficiency within the building sector is imperative to curbing energy losses, given that this sector alone contributes to over 34% of global energy consumption. Employing a building management system, along with its regular updates, presents a strategic avenue to decrease energy usage, enhance building energy efficiency, and more. Tailored control strategies, aligned with the unique characteristics and usage patterns of each building, are essential for achieving energy savings. This article presents an evaluation of HVAC system efficiency in office buildings, utilizing a data-driven approach coupled with simulations conducted in IDA ICE software. The research explores the control strategy of an office building equipped with a constant air volume HVAC system, featuring a regularly controlled air handling unit. The objective is to boost energy efficiency while striking a balance between occupant comfort and energy consumption. Findings indicate that by analyzing measured data and adjusting configurable parameters, building energy consumption can be significantly reduced. Close monitoring of indoor parameters by building operators and corresponding adjustments to the HVAC system can yield energy savings of up to 16%. Leveraging these insights, the paper suggests integrating data-driven and dynamic simulation methods into building management system models to optimize HVAC systems, enhance energy efficiency, and advance ambitious carbon neutrality objectives.

The building envelope has the most significant contribution in the reduction of the building energy consumption. Application of new, alternative and improved materials and systems has an important impact on the buildings performances. This paper is focused on the thermal transmittance, as an indicator of the thermal conductance of the construction element. It includes comparisons of the U-values, calculated by software, with those measured in situ on three representative façade walls. The walls have been constructed with the new wall system Fragmat NZ-1, a new product in Macedonian buildings. This research provides basic information on the thermal transmittance of the system. The results of the analysis show that the in situ measuring is a useful tool in validation of the precision of analytically calculated values, since it was difficult to obtain precise results from the analytical calculations only, especially when the layers are with non-uniform thickness.

The Double U-pipe ground heat exchanger, recognized for its straightforward process, cost-effectiveness, high heat exchange efficiency, and low thermal resistance, stands as the predominant ground heat exchanger type in today's shallow geothermal energy development and utilization. Recent years have seen significant research into the heat transfer influencing factors and heat exchange performance of Double U-pipe ground heat ex-changers via experimental testing methods. Yet, studies integrating numerical simulation with in-situ testing have been less frequent. Drawing on the cylindrical heat source model theory and the outcomes of regional in-situ thermal response tests, this paper develops a Double U-pipe ground heat transfer model by establishing physical, mathematical, and heat transfer geometric models. It assesses the impact of varying inlet temperatures, flow rates, and initial ground temperatures on heat exchange efficiency under heating conditions. The results validate the precision of the double U-pipe ground heat exchanger model based on in-situ testing. They show that enhancing the temperature differential between the inlet and initial temperatures, elevating the initial ground temperature, and moderately increasing the flow rate can boost the system's heat exchange efficiency.

A study about influence of heat input on welding defects in vertical upward welding position for dissimilar material and thickness using a new variation of TIG welding torch is done with support of advanced inspection methods SEM and EBSD. With vertical upward welding position, control heat input plays an important role to keep the weld stabilization without defects. On the other hand, TIG welding process using a conventional TIG torch (conventional TIG welding process) has low efficiency and it is difficult to control heat input with high accuracy. So, it is considered that using conventional TIG torch is still a challenge for welding thin plates. In this case, a new variation of TIG torch has been developed. This torch used a constricted nozzle to improve plasma arc characteristics. As a result, it can control efficiently the heat input to prevent the excessive or insufficiency for joining thin sheets. For evaluation of welding quality, advanced examination methods SEM and EBSD were applied to directly observe the welding defects. From the results, the formation mechanism of blowhole inside weld zone in case of welding dissimilar material and thickness was discussed. It is pointed out that when sufficient welding current, the change from weld zone to base metal is uniform, no welding defects such as blowhole was seen. However, in case of low welding current, the thinner base metal is insufficient fusion and the change between weld zone and base metal is not uniform. The blowhole was observed at SS400 material side.

The automation of welding processes requires the use of automated systems and equipment, in many cases industrial robotic systems, to carry out welding processes that previously required human intervention. Automation in the industry offers numerous advantages, such as increased efficiency and productivity, cost reduction, improved product quality, increased flexibility and safety, and greater adaptability of companies to market changes. The field of welding automation is currently undergoing a period of profound changes due to a combination of technological, regulatory, and economic factors worldwide. Nowadays, the most relevant aspect of the welding industry is to meet customer requirements by satisfying their needs. To achieve this, the automation of the welding process through sensors and control algorithms ensures the quality of the parts and prevents errors such as porosity, unfused areas, deformations, excessive heat, etc. This paper proposes an intelligent and adaptive system based on the measurement of welding joints using laser scanning and the subsequent analysis of the obtained point cloud to adapt the welding trajectories.

MIMO (multiple-input multiple-output) radar provides much more flexibility than the traditional radar for its ability to realize far more observation channels than the actual number of T/R (transmit and receive) elements. Designing the array of MIMO imaging radar, the commonly used virtual array theory generally assumes that all elements are placed on the same line. However, due to the physical size of the antennas and coupling effect between T/R elements, a certain height difference between T/R arrays is essential, resulting in the defocusing of edge points of the scene. On the other hand, the virtual array theory implies far-field approximation, leading to inevitable high grating lobes in the imaging result of near-field edge points of the scene observed by common MIMO array. To tackle these problems, this paper derives the relationship between target’s PSF (point spread function) and pattern of T/R arrays, by which the design criterion of near-field imaging MIMO array is presented. Firstly, the proper height between T/R arrays is designed to focus the near-field edge points well. Secondly, the far-field array is modified to suppress the grating lobes in the near-field area. Finally, the validity of the proposed methods is verified by simulations and an experiment.

As modern systems are becoming more complex their control strategy cannot longer relay only on measurement information that usually comes from probes but also from mathematical models. Those systems models can lead to unbearable computation times due to their own complexity, turning the control process non-viable, which leads to the implementation of surrogate models that enable to achieve estimates within acceptable time to take decisions. A control trained with Deep Reinforcement Learning algorithm, using a Physics-Informed Neural Network to obtain the temperature map on the following time step, replaces the need of running Direct Numerical Simulations. On this work we considered an 1D heat conduction problem, which temperature distribution feeds a control system to activate a heat source aiming to obtain a constant, previously defined, temperature value. With this approach, control training becomes much faster without the need of performing numerical simulations or laboratory measurements, as well the control is taken based on Neural Network enabling its implementation on simple processors to edge computing.

Это исследование сосредоточено на разработке системы искусственного зрения для гибкого дельта-робота-манипулятора и ее интеграции с межмашинной связью для оптимизации взаимодействия устройств в реальном времени. Эта интеграция направлена ​​на увеличение скорости роботизированной системы и улучшение ее общей производительности. Предлагаемое сочетание системы искусственного зрения с межмашинной связью позволяет обнаруживать и распознавать цели с высокой точностью в режиме реального времени в ограниченном пространстве, предназначенном для позиционирования, дальнейшей локализации и выполнения производственных процессов, таких как сборка или сортировка деталей. . В данном исследовании RGB-изображения используются в качестве входных данных для алгоритма MASK-R-CNN, а результаты обрабатываются в соответствии с особенностями прототипа дельта-манипулятора робота. Данные, полученные от MASK-R-CNN, адаптированы для использования в системе управления дельта-роботом с учетом ее уникальных характеристик и требований к позиционированию. Технология M2M позволяет манипулятору робота быстро реагировать на изменения, например, на перемещение объектов или изменение их положения, что имеет решающее значение для задач сортировки и упаковки. Система была протестирована в условиях, близких к реальным, чтобы оценить ее производительность и надежность.

In this paper, we study the well-posedness and asymptotics of a one-dimensional thermoelastic laminated beam system either with or without structural damping, where the heat conduction is given by Fourier's law effective in the rotation angle displacements. We show that the system is well-posed by using Lumer-Philips theorem, and prove that the system is exponentially stable if and only if the wave speeds are equal, by using the perturbed energy method and Gearhart-Herbst-Prüss-Huang theorem. Furthermore, we show that the system with structural damping is polynomially stable provided that the wave speeds are not equal, by using the second-order energy method.

So far, scientific studies on high frequency welding (HF) have observed the three main parameters: anode current, welding time and pressure of upper electrode. Some authors have also observed and studied the welding frequency, the power, and the values of the dielectric constants of the materials or the angle of dielectric losses. Due to the complex effects that the parameters have on the quality of the welded joint, it is necessary to extend the research and study the mutual relationships between a large numbers of process parameters on the welded joint in order to achieve satisfactory strength of the welded joint. In this research, the number of considered parameters is increased to 17, each of which is relevant to the processes of HF welding, and their mathematical equations are presented. The research is carried out on a HF welding machine improved with a linear pneumatic actuator for lowering the upper electrode and regulating the compressive force, and a measuring machine with the appropriate measuring method for determining the breaking forces with a tension gage and performing the „T“ test is made. Numerous researches were carried out on the functional changes of the process parameters of the percentage share of the values of the coupling capacitor, the anode current and the welding time on the values of the breaking forces of the welded joints. Based on the conducted research, it was concluded that the optimization of the process parameters of HF machine must be performed before the welding process, which is determined by a certain amount of energy that must be introduced into the material. These parameters are the capacity of the output capacitor, i.e., the value of the electric current flowing through the material and the time for the development of the operating power to produce welded joints with a certain strength and quality of welded joints for a specific material used in the process.

Dissimilar welds between ferritic and austenitic steels represent a good solution for exploiting the best performance of stainless steels at high and low temperatures and in aggressive environments, while minimizing costs. Therefore, they are widely used in nuclear and petrochemical plants, however, due to the different properties of the steels involved, the welding process can be challenging. Fusion welding can be specifically addressed to connect low-carbon, or low-alloy steels, with high-alloy steels, which have similar melting point. Welding of thick plates can be performed with electric arc in multiple passes or in a single pass by means of a laser beam equipment. Since microstructure and consequently mechanical properties of the weld are closely related to composition, the choice of the filler metal and processing parameters, which in turn affects the dilution rate, plays a fundamental role. Numerous technical solutions were proposed for welding dissimilar steels and much research was developed on the weldment metallurgy; therefore, this article is aimed at a review of the most recent scientific literature on the issues relating to the fusion welding of ferritic / austenitic steels. Two specific sections are dedicated respectively to electric arc and laser beam welding; finally, metallurgical issues, related to dilution and thermal field are debated in the discussion section.

This paper proposes a novel single-stage buck-boost three-Level neutral-point-clamped (NPC) inverter with two independent dc sources coupled for the grid-tied photovoltaic (PV) application, which can effectively solve the unbalanced operational conditions generally appeared between two coupled independent PV sources induced by the unequal irradiation and temperature distribution. The proposed control scheme can simultaneously guarantee the maximum power point (MPP) operation of both PV sources and maintain the output waveform quality. Compared to the traditional two-stage PV inverter, the proposed NPC inverter could reduce the PV array voltage requirement and dc-link capacitors’ voltage rating, meanwhile show the advantage in operational efficiency. MATLAB simulations and the captured experimental results are presented to show the performance of the proposed three-level inverter.

Reservoir computing is a machine learning method that uses the response of a dynamical system to a certain input in order to solve a task. As the training scheme only involves optimising the weights of the responses of the dynamical system, this method is particularly suited for hardware implementation. Furthermore, the inherent memory of dynamical systems which are suitable for use as reservoirs mean that this method has the potential to perform well on time series prediction tasks, as well as other tasks with time dependence. However, reservoir computing still requires extensive task dependent parameter optimisation in order to achieve good performance. We demonstrate that by including a time-delayed version of the input for various time series prediction tasks, good performance can be achieved with an unoptimised reservoir. Furthermore, we show that by including the appropriate time-delayed input, one unaltered reservoir can perform well on six different time series prediction tasks at a very low computational expense. Our approach is of particular relevance to hardware implemented reservoirs, as one does not necessarily have access to pertinent optimisation parameters in physical systems but the inclusion of an additional input is generally possible.

This study evaluates the input efficiency of greenhouse tomato and pepper farms in Kosovo. Using data collected from farm surveys, we conduct an input-oriented data envelopment analysis (DEA) to empirically assess input efficiency. Secondly, linear regression analysis is used to investigate which farm variables predict greenhouse tomato and pepper technical efficiency (TE). The DEA results indicated that among the seven regions in Kosovo, Prizren emerged as the most efficient greenhouse tomato producing region with a mean efficiency of 0.83 (on a scale of 0 to 1). Prishtina followed with a mean efficiency of 0.80. In the production of greenhouse peppers, Prishtina was the most efficient region with a mean efficiency of 0.99. Ferizaj followed with a mean efficiency of 0.93. Conclusions about farm characteristics that explain differences in efficiency were sensitive to model specification. Nevertheless, depending on the structural and operational characteristics of the greenhouse tomato and pepper farms, there is an opportunity for the technically inefficient farms and regions to improve their use of inputs.

A multi-strand composite welding wire was applied to join high nitrogen austenitic stainless steel, and microstructures and mechanical properties were investigated. The electrical signals demonstrate that the welding process using a multi-strand composite welding wire is highly stable. The welded joints are composed of columnar austenite and dendritic ferrite and welded joints obtained under high heat input and cooling rate have a noticeable coarse-grained heat-affected zone and larger columnar austenite in weld seam. Compared with welded joints obtained under the high heat input and cooling rate, welded joints have the higher fractions of deformed grains, high angle grain boundaries, Schmid factor and the lower dislocation density under the low heat input and cooling rate, which indicate a lower tensile strength and higher yield strength. The rotated goss (G_RD) orientation of a thin plate and the cube (C) orientation of a thick plate are obvious after welding, but the S orientation at 65° sections of Euler’s space is weak. The δ-ferrite was studied based on the primary ferrite solidification mode. It is observed that low heat input and high cooing rate result in the increasing of δ-ferrite and high dislocation density was obtained in grain boundaries of δ-ferrite. M₂₃C₆ precipitates due to low cooling rate and heat input in weld seam and deteriorates the elongation of welded joints. The engineering stress-strain curves also show the low elongation and tensile strength of welded joints under low heat input and cooling rate, which is mainly caused by the high fraction of δ-ferrite and the precipitation of M₂₃C₆.

Chemical vapor deposition (CVD) is a vital process for depositing thin films of various materials with precise control over thickness, composition, and properties. Understanding the heat and mass transfer mechanisms during CVD is essential for optimizing process parameters and ensuring high-quality film deposition. This review provides an overview of recent advancements in the heat and mass transfer modeling for chemical vapor deposition processes. It explores innovative modeling techniques, recent research findings, emerging applications, and challenges in the field. Additionally, it discusses future directions and potential areas for further advancement in CVD modeling.

Employing numerical methods to simulate manufacturing processes and study their influential factors is increasing. The development of computers and engineering software has increased the ability and accuracy of numerical methods in simulating various aspects of different processes. One of the manufacturing processes that has been considered by many industries in recent years to join metals in solid-state with unique properties is called friction stir welding. It is challenging and, in some cases, impossible to experimentally study the various aspects of this process, such as temperature distribution, stress distribution, and material flow, due to severe plastic deformation in the weld zone. In this case, numerical methods are used to investigate these parameters and better understand the process. This study first investigates various numerical methods researchers use to simulate the process. The ability, pros, and cons of these methods to simulate the process are also examined. Then, the applications of numerical models in simulating the temperature distribution during the process as well as the effects of input parameters on the temperature history of the process, are deeply considered. Next, the application of numerical methods in material flow modeling during the process is investigated. Finally, the modeling of the microstructure of the welding zone is investigated using numerical methods that help significantly in predicting the weld microstructure.

Steel structures, such as bridges, must be continuously maintained. Due to increasing trac loads, design and execution shortcomings, many steel bridges are subject to various types of damage, such as cracks. The bridges must be maintained by crack removal and re-welding the cracks. During this work, the bridge is closed for trac in order to suppress the crack ank movement during welding. As a result, trac loads on other routes are higher, which increases further damage on detour routes and subsequently additional welding work and costs on theses structures. Therefore, the aim is to provide a method that allows welding work on steel structures under running trac, respectively under cyclic loads. First, measurements at a representative steel bridge were conducted to derive gap opening parameters of amplitude and frequency for welding tests under cyclic loads. In a test setup for reproducible and comparable welding tests, specimen were welded under cyclic loads. Deep grinding of the root layer allowed defect-free welding within the range of 0.1 mm amplitude at a frequency of 2 Hz loadings. For such welds, the weld quality and the fatigue strength was comparable to the standard requirements.

When a railway vehicle moves on a curved rail, sliding contact occurs between the rail head side and wheel flange, which wears the wheel flange down. The thinned flange needs to be restored above the required minimum thickness for structural safety. In this study, a new process and welding wire for restoring worn-out railway wheels by submerged arc welding was developed. To characterize the properties of the restored wheel, dilatometric analysis of phase transformation, SEM/EDX analyses, hardness measurement, and residual stress measurement using the X-ray diffraction method were performed. Finally, wear tests with full-size wheel/rail specimens were carried out. It was confirmed that the weld metal was composed of bainitic microstructures as intended, and welding defects were not observed. The wear amount of the restored wheel was greater than that of the base material, but it was less than half of the wear depth of the weld-repaired wheel with ferritic–pearlitic microstructures. The developed process seems applicable to industry.

The most important plastic resins used for wire coating are Polyvinyl Chloride (PVC), Nylon, Polysulfone and Low-high density polyethylene (LDPE / HDPE). In this article,the coating process is performed using elastic-viscous fluid as a coating material for wire coating in a pressure type coating die. The elastic-viscous fluid is electrically conducted in the presence of an applied magnetic field. The governing non-linear equations are modeled and then solved analytically by utilizing an Adomian decomposition method (ADM). The convergence of the series solution is established. The results are also verified by Optimal Homotopy Asymptotic Method (OHAM). The effect of different emerging parameters such as non-Newtonian parameters α and β, magnetic parameter M and the Brinkman number Br on solutions (velocity and temperature profiles) are discussed through several graphs. Additionally, the current result also compares with the published work already available in the literature.

The purpose of this study is to investigate the influence of heat stress on some biochemical parameters in the blood of dairy cows raised in Bulgaria. The study was conducted on a dairy farm with a capacity of 500 cows, Holstein breed, raised in free-group housing in individual resting boxes. The research was carried out over three seasons: spring, summer, and autumn, with a total of 90 blood samples collected from the cows raised on the farm - 30 blood samples for each season, including cows from the 30th to the 60th day of lactation. Temperature and humidity data were obtained from the nearest meteorological station to the farm. Based on this data, the minimum, average, and maximum values of the temperature-humidity index were calculated. The analysis of variance revealed that the month of the study significantly influenced the following blood parameters: glucose, urea, total protein, cortisol, prolactin, and Ca (P < 0.001). Analysis of the data expressed by LS mean values clearly shows that during the hot months, dairy cows experience a deficit of energy from carbohydrate sources, which they compensate for from other non-carbohydrate sources. Confirmation of this is seen in the blood glucose values, which during the summer are 1.50 mmol/l, approximately twice as low as the values measured during spring and autumn. Regarding urea concentration, a final product of protein metabolism, the values recorded during the summer are 5.3 mmol/l, 1.5 times higher compared to other study periods. As a result of the metabolic load on the liver, the values of hepatic enzymes (ASAT and ALAT) decrease during the summer months, respectively to 93.92 and 17.68 U/L. Cortisol levels in the blood during the summer were registered at 50.92 nmol/l, indicating that cows are under stress. Values for prolactin are of interest, with the highest values being recorded in spring - 1.09 mlU/I. During the summer and autumn studies, the values are 0.99 and 0.89 mlU/I, respectively. A similar trend of decreasing values from spring to autumn season is observed in total blood protein, namely 89.93; 81.99, and 74.36 g/l.

This article discusses the application of thermal quality control methods for plant tissues. The purpose of the work is to determine the optimal parameters of thermal impact on a spherical-shaped plant control object, ensuring the detection of surface and subsurface defects. The authors of the work proposed mathematical models of the temperature field for a spherical body with defects and a flat sample when exposed to the thermal influence of a pulsed source. As a result of the use of mathematical models, the thermophysical characteristics of plant tissues of varying degrees of disease damage were obtained, which made it possible to simulate the temperature field of the control object and obtain an image of classified tissues. The developed recommendations made it possible to select the optimal parameters of the thermal effect on the test object.

These findings have several policy implications, emphasizing the need for enhanced data collection, climate-resilient agricultural policies, and continued investment in research. The study contributes to the understanding of climate-smart agriculture, providing insights for informed decision-making towards resilient and productive agricultural systems in the face of climate change challenges.

Life Cycle Assessment (LCA) methodology is increasingly prevalent in the quantification of environmental status in the building sector, following new legislative frameworks. Countries need to quantify and assess their environmental impacts as a previous base for regulation and decision making. In this context, standardised national data sets are being developed, based on consensus with manufacturers: sectoral Environmental Product Declarations. This study focuses on assessing these EPDs with the aim of providing relevant information for global decision-making, focusing on consistency and pointing out shortcomings. An assessment has been carried out both at national level, considering all sectoral EPDs and declared products, and at international level, with three common building materials (brick, steel and concrete). The results highlight the lack of traceability in the development and assessment of uncertainty, resulting in substantial discrepancies in reported impacts, especially in the later stages of the life cycle (up to 90% difference). Meanwhile, impacts such as Global Warming Potential or total renewable and non-renewable primary energy use show homogeneous values in the cradle-to-gate stages with differences generally less than 10%. The analysis of sectoral EPDs should be a design guide with environmental sustainability criteria, as the last section of this study attempts to focus on.

Due to environmental concerns, natural refrigerants and their use in refrigeration and air conditioning systems are receiving more attention from manufacturers, end users and the scientific community. The study of heat transfer and pressure drop is essential for accurate design and more energy efficient cycles using natural refrigerants. The aim of this work is to provide an overview of the latest outcomes related to heat transfer and pressure drop correlations for ammonia, propane, isobutane and propylene and to investigate the current state of the art in terms of operating conditions. Available data on the existing correlations of heat transfer coefficient and pressure drop for natural refrigerants have been collected through a systematic search. Whenever possible, validity intervals are given for each correlation and the error is quantified. It is the intention of the authors that this could be a valuable support for researchers and an aid to design, with particular reference to heat pumps. A procedure based on the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) statement was adopted, and the Scopus database was used to query the relevant literature. A total of 135 publications qualified for inclusion in the survey; 34 articles report experimental investigations for not usual geometric conditions. Of the 101 selected papers related to usual geometric conditions, N = 50 deal only with HTC, N = 16 deal only with pressure drop and the remainder (N = 35) analyse both HTC and pressure drop. Among the 85 HTC papers (N = 53) deal with the evaporating condition, N = 30 with condensation and only N = 2 with the heat transfer correlations under both conditions. Most of the 101 articles concern propane and isobutane. The high temperatures are less widely investigated.

Crystallization often occurs in the laser welding of amorphous alloys, reducing the amorphous alloys’ properties. So, it is necessary to simulate the temperature field curve of the welding area by computer and then determine the power and laser moving speed of laser welding. In this paper, the temperature field curve of Zr41.2Ti13.8Cu12.5Ni10Be22.5(Vit1) amorphous alloy in laser welding is obtained by finite element analysis. The continuous heating curve (CHT) of Vit1 is fitted by the Vogel-Fulcher-Tammann (VFT) equation and the Kissinger equation. If the temperature field curve intersects with the CHT curve, crystallization occurs. The experiment results show that the VFT equation can be used to predict the crystallization of Vit1 better in laser welding. The tem-perature and welding time are increased by using low welding speed. Therefore, the temperature of the weld zone cannot fall in time, resulting intersection of the temperature field curve and the CHT curve. So, crystallization can be avoided if the welding speed is controlled within a rea-sonable range, and the highest temperature is kept under the CHT curve.

Despite being stored at 113 K and atmospheric pressure, LNG cold potential is not exploited to reduce green ships’ energy needs. An innovative system based on three Organic Ranking Cycles integrated into the regasification equipment is proposed to produce additional power and recover cooling energy from condensers. A first-law analysis identified ethylene and ethane as suitable working fluids for the first and the second ORC making available freshwater and ice. Propane, ammonia and propylene could be arbitrarily employed in the third ORC for air-conditioning. An environmental analysis that combines exergy efficiency, ecological indices and hazard aspects for marine environment and ship’s passengers, indicated propylene as safer and more environmentally friendly. The exergy analysis confirms more than 20% of the LNG potential can be recovered from every cycle to produce a net clean power of 76 kW, whereas 270 kW can be saved by recovering condensers' cooling power to satisfy some ship needs. Assuming the sailing mode, a limitation of 162 kg in LNG consumptions was determined, avoiding the emission of 1584 kg of CO2 per day. Marine thermal pollution is reduced by 3.5 times by recovering the working fluids' condensation heat for the LNG pre-heating.

This paper presents a new semi-explicit algorithm for parameters estimation in a time-fractional generalization of dual-phase-lag heat conduction model with the Caputo fractional derivatives. It is shown that this model can be derived from a general linear constitutive relation for the heat transfer by conduction when the heat conduction relaxation kernel contains the Mittag-Leffler function. The model can be used to describe heat conduction phenomena in a material with power-law memory. The proposed algorithm of parameters estimation is based on the time integral characteristics method. The explicit representations of the thermal diffusivity and the fractional analogues of the thermal relaxation time and the thermal retardation are obtained via a Laplace transform of the temperature field and utilized in the algorithm. An implicit relation is derived for the order of fractional differentiation. In the algorithm, this relation is resolved numerically. An example illustrates the proposed technique.

Many cryptographic systems require random numbers, and weak random numbers lead to insecure systems. In the modern world, there are several techniques for generating random numbers, of which the most fundamental and important methods are deterministic extractors proposed by von Neumann, Elias, and Peres. Elias’s extractor achieves the optimal rate (i.e., information theoretic upper bound) h(p) if the block size tends to infinity, where h(·) is the binary entropy function and p is probability that each bit of input sequences occurs. Peres’s extractor achieves the optimal rate h(p) if the length of input and the number of iterations tend to infinity. The previous researches related to both extractors did not mention practical aspects including running time and memory-size with finite input sequences. In this paper, based on some heuristics, we derive a lower bound on the maximum redundancy of Peres’s extractor, and we show that Elias’s extractor is better than Peres’s one in terms of the maximum redundancy (or the rates) if we do not pay attention to time complexity or space complexity. In addition, we perform numerical and non-asymptotic analysis of both extractors with a finite input sequence with any biased probability under the same environments. For doing it, we implemented both extractors on a general PC and simple environments. Our empirical results show that Peres’s extractor is much better than Elias’s one for given finite input sequences under the almost same running time. As a consequence, Peres’s extractor would be more suitable to generate uniformly random sequences in practice in applications such as cryptographic systems.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

Densely urbanized areas, with a low percentage of green vegetation, are highly exposed to Heat Waves (HW) which nowadays are increasing in terms of frequency and intensity also in the middle-latitude regions, due to ongoing Climate Change (CC). Their negative effects may combine with those of the UHI (Urban Heat Island), a local phenomenon where air temperatures in the compact built up cores of towns increase more than those in the surrounding rural areas, with significant impact on the quality of urban environment, on citizens health and energy consumption and transport, as it has occurred in the summer of 2003 on France and Italian central-northern areas. In this context this work aims at designing and developing a methodology based on aero-spatial remote sensing (EO) at medium-high resolution and most recent GIS techniques, for the extensive characterization of the urban fabric response to these climatic impacts related to the temperature within the general framework of supporting local and national strategies and policies of adaptation to CC. Due to its extension and variety of built-up typologies, the municipality of Rome was selected as test area for the methodology development and validation. First of all, we started by operating through photointerpretation of cartography at detailed scale (CTR 1: 5000) on a reference area consisting of a transect of about 5x20 km, extending from the downtown to the suburbs and including all the built-up classes of interest. The reference built-up vulnerability classes found inside the transect were then exploited as training areas to classify the entire territory of Rome municipality. To this end, the satellite EO HR (High Resolution) multispectral data, provided by the Landsat sensors were used within a on purpose developed "supervised" classification procedure, based on data mining and “object-classification” techniques. The classification results were then exploited for implementing a calibration method, based on a typical UHI temperature distribution, derived from MODIS satellite sensor LST (Land Surface Temperature) data of the summer 2003, to obtain an analytical expression of the vulnerability model, previously introduced on a semi-empirical basis.

In recent decades, many attempts have been made to automate the entire welding process, how-ever, there remain many non-automated welding operations that present a constant hazard to workers. This article presents an automated welding solution with collaborative robots, with this contribution, we intend to help companies in this sector increase productivity, improve quality, effectively reduce costs, and improve working conditions.

The use of different sources to energize a load is convenient in many applications, particularly those where two or more renewable energy sources are employed as: energy harvesting, hybrid vehicles, and off-grid systems. In these cases, a multi-input converter able to admit sources with different characteristics and, if necessary, select the output power of each source. Several topologies of multi-input converters have been proposed to this aim, however, most of them are based on multi-stage designs, which decreases efficiency and increases control complexity, particularly when more than two sources are used. In this work, a three-input step-up converter easy to control in open loop condition is analyzed. A designed procedure is described, and experimental results are presented for a 1 kW power converter. The implemented converter results in a higher voltage gain, less storage element keeping high efficiency compared to similar topologies. Using the procedure here proposed, this converter that was initially proposed for photovoltaic applications is enabled to be used in medium and high-power applications, for example when renewable energy sources are used.

Brain tumor being one of the major health hazards always needs a prompt diagnosis for the early treatment options to improve the chances of the survival of the patients. Traditional manual assessment of MRI (magnetic resonance imaging) to identify these conditions is a common practice. Hence, automation of the diagnosis practices can considerably improve the quality of the treatment procedures. In recent years almost every method for the automated diagnosis of brain tumor detection uses a deep learning technique. Despite decent works current techniques need a significant improvement to produce better results. Along with failure to produce decent results, the current deep learning models present very complex architectures which sometimes require huge computational resources. Therefore, in this paper we present a novel method that uses a lightweight dual-stream model with dual-input to detect brain tumors on MRI images. Both the inputs use different pre-processing mechanisms based on Contrast Limited Adaptive Histogram Equalization (CLAHE) and White Patch Retinex algorithm in order to enhance the feature learning capabilities of the proposed model. In addition, the proposed method uses a two-fold margin loss to boost training process for better feature learning. The proposed method produces state-of-the-art results for the detection of Glioma, Meningioma and Pituitary tumors. The model presents accuracy of 99%, 98% and 99% respectively for Glioma, Meningioma and Pituitary tumor detection.

In this study, an alternative method to conventional production methods involving thin section copper permanent mould casting (rapid solidification), hot rolling and heat treatment processes to manufacture AISI DC 53 cold work tool steel, has been investigated. In this new method, solidification of the AISI DC 53 was done in the thin section copper mould instead of traditional ingot casting. After solidification, thin slabs obtained was homogenized to 1150 ^oC and hold at this temperature for one hour and then hot rolling was be applied. During hot rolling process, about % 30 reduction in thickness of slab was obtained. After hot rolling, heat treatment (austenitizing, quenching and tempering) have been applied to thin slab. The samples have been taken as cast, as rolled and as heat treated (austenitized and tempered) and the microstructural analysis, hardness tests, retained austenite quantity measurement by XRD method have been performed. The heat treatment and tests have been performed for a commercially available AISI DC 53 which is manufactured by thick section ingot casting and rolling. Hardness values of the AISI DC 53 steels produced by traditional route is in the range of 52-54 HRC after austenitization at 1025 ^oC for one hour and quenched in compressed air and tempered twice at 525 ^oC for 120 mins. On contrary the permanent mould cast AISI DC 53 after homogenization at 1150 ^oC and immediately hot rolling then air cooling and austenitized at 1025 ^oC for one hour then quenched by compressed air and tempered twice at 525 ^oC for 120 mins have hardness valeus in the range of 55-57 HRC. Experiments have revealed that the properties of new rapid solidified steel in permanent copper mould are better than the commercially available steel and have a more refined microstructure than commercially produces alternative. Therefore, the new proposed method can be used as an alternative manufacturing method for cold-work tool steels.

Nonwoven fabrics have been widely used in textile manufacturing industry as a sheet or web structure because of soft, water-repellent, recycle, ecological and resilient functions. Ultrasonic welding method has been applied for bonding nonwoven fabrics due to clean, fast and reliable approach. In this work, the ultrasonic stepped horn is designed to generate uniform amplitudes on the working surface by using finite element analysis (FEA) simulation. Chromium carbon steels are utilized to produce ultrasonic horns due to high wear resistant and hardness. Isotactic polypropylene nonwoven fabrics fabricated by spunbond process were bonded by continuous ultrasonic sewing machine. Ultrasonic horn with 70 mm in diameter working at 20 kHz, polypropylene (PP) nonwoven density of 80 gsm and various design of welding joints were applied. A typical image in the case of number one was investigated by the scanning electron microscope (SEM) images of inter-facial micro-structure. However, welding joints of totally eight roller patterns was test the tensile strength of the ultrasonic welding joints on PP nonwoven fabrics. The tensile strength of the welding joints is proportional to the area ratio between the welding area and cycling area. The results showed that the melted zone without welding defects such as crack or blowhole can be seen. Furthermore, the tensile strength of welding joints in eight cases of roller patterns (No.1-No.8) was described in details. The ultrasonic welding joints with brick structures give higher tensile strength while the solid line in the pattern gave less strength.

Proteins possess complex three-dimensional structures, and these structures are stable only within specific ranges of temperature which mostly correspond to the temperature ranges of the host organisms. However, few exceptional proteins, called heat-stable proteins, are stable at temperatures that are substantially higher than those tolerated by the host organisms themselves. Most of the heat-stable proteins possess heat stability to perform their functions at high temperatures, but some of them are intrinsically heat-stable due to their structure. Heat-stable proteins are usually divided into three or four groups depending upon the intricacies of their structures and thermal behaviors. Their peculiar property, i.e. heat-stability, makes them very valuable in applications such as polymerase chain reaction, industrial processes requiring high temperature, and protein engineering. Heat-stability also makes it feasible to purify such proteins, from the rest of the heat-labile proteins, using a simple heat-treatment method. Moreover, heat treatment can be used as a combined cell-lysis and protein purification step which, as compared to conventional methods, can result in a higher yield of heat-stable proteins. Furthermore, some special heat-stable proteins, i.e. intrinsically disordered proteins (which include the proteins involved in important neurodegenerative diseases), need heat-treatment step, in some cases, as the only way for their successful purification and study. Hence, this paper provides a first-ever comprehensive review of all major aspects of heat-stable proteins, i.e., their structure, evolution, classification, significance, and heat-treatment mediated purification.

CoCrFeNiMn high-entropy alloy coatings were prepared on compacted graphite iron（CGI） through plasma cladding to strength the CGI substrate. The effects of heat treatment temperatures and times on the microstructure and mechanical properties of the CoCrFeNiMn coatings were investigated. After heat treatment, a single FCC phase was remained in the coating as compared to the deposited one, with smaller dendrites, larger dendritic spacing and more Cr-rich compounds precipitated between dendrites. The coatings’ microhardness was increased after heat treatment. After heat treated at 660°C for 90 minutes, the coating had the highest microhardness of 563±6.9 HV0.2, the lowest frictional coefficient of 0.71 and the smallest wear mass loss of 1.12 mg, and it had the best wear resistance.

This research paper presents a deep learning approach to early detection of skin cancer using image augmentation techniques. The authors propose a two-stage image augmentation technique that involves the use of geometric augmentation and generative adversarial network (GAN) to classify skin lesions as either benign or malignant. This research utilized the public HAM10000 dataset to test the proposed model. Several pre-trained models of CNN were employed, namely Xception, Inceptionv3, Resnet152v2, EfficientnetB7, InceptionresnetV2, and VGG19. Our approach achieved accuracy, precision, recall, and F1-score of 96.90%, 97.07%, 96.87%, 96.97%, respectively, which is higher than the performance achieved by other state-of-the-art methods. The paper also discusses the use of SHapley Additive exPlanations (SHAP), an interpretable technique for skin cancer diagnosis, which can help clinicians understand the reasoning behind the diagnosis and improve trust in the system. Overall, the proposed method presents a promising approach to automated skin cancer detection that could improve patient outcomes and reduce healthcare costs.

Traditional potential transformers have problems of large volume, difficulty in insulation, iron core saturation, ferroresonance overvoltage and poor transient response characteristics. The voltage sensor based on the principle of electric field coupling and differential input structure does not need to contact the measured object or ground, and can avoid the above problems. However, it requires a sufficiently high capacitance between the differential electrodes to obtain sufficient accuracy and a high voltage division ratio. The existing method of using mutual capacitance between the differential electrodes will cause many problems and fail to meet the practical needs. To solve the above problems, this paper innovatively uses multi-layer ceramic capacitor to replace the mutual capacitance and designs a new type of voltage sensor. In addition, by using single bypass small resistance grounding method to increase the input impedance of the differential signal processing circuit, error of the sensor is further reduced. The experimental results show that the sensor has excellent accuracy and great transient response characteristics. The ratio error under power frequency is within ±0.5% and the phase error is within 1. The ratio error in the range of 500 Hz∼30 kHz is within ±5% and the phase error is within 5. Moreover, it has the advantages of low cost, miniaturization, flexible shape and easy to adjust the voltage division ratio. These characteristics indicate that the sensor has good voltage measurement and sensor network potential.

With the development of energy internet, integrated energy system can effectively reduce carbon emissions and improve the utilization of renewable energy. In this paper, a low-carbon optimal scheduling model of integrated energy system considering heat loss of heat network pipeline is proposed. Based on the study of concentrating solar power (CSP) plant and heat storage tank (HS), an optimal scheduling model is established, which takes system operation cost, environmental pollution and penalty cost of abandoning wind and solar energy as objectives. Through the analysis of example results, it is proved that the model proposed in this paper can achieve the goal of reliable, low-carbon and economic operation of the system. At the same time, it shows that CSP unit can reduce the operation cost of system and increase energy coupling and utilization.

Reservoir computing (RC) systems can efficiently forecast chaotic time series using nonlinear dynamical properties of an artificial neural network of random connections. The versatility of RC systems has motivated further research on both hardware counterparts of traditional RC algorithms and more efficient RC-like schemes. Inspired by the nonlinear processes in a living biological brain and using solitary waves excited on the surface of a flowing liquid film, in this paper we experimentally validate a physical RC system that substitutes the effect of randomness for a nonlinear transformation of input data. Carrying out all operations using a microcontroller with a minimal computational power, we demonstrate that the so-designed RC system serves as a technically simple hardware counterpart to the `next-generation’ improvement of the traditional RC algorithm.

The process model is very essential for the model based control design. The model of the process can be identified using system identification algorithm. The system identification is done through the open loop and closed loop approaches. In this work, the lab scale conical tank setup configured as a non square MIMO system. The conical tank system is identified through the both appraoches, the effectiveness and need of the both approaces are discussed. Based on the open loop identified model the controller designed and the controller implemented in the real time the to record the process data. From this data the closed loop identification are conducted uisng N4SID algorithm. The controller seetings are obtained using the smith predcitor based IMC based PI controller for the obtained model. The proposed identification algorithm and controller tuning show the better reults over the conventional method. Moreover, this method is applicable for all the non square MIMO system.

Global warming and the associated increasing frequency of heatwaves are on the rise leading to numerous health complications. Diabetic patients are more vulnerable to heat exposure than healthy individuals, owing to their impaired sweating ability, however, little is known about how heat exposure may impact the function of skin cells, commonly keratinocytes. Our recent report provided the first proof-of-concept revealing that the metabolic composition of sweat EVs is associated with metabolic changes in healthy individuals and type 2 diabetes patients. Given this and the shared cellular proprieties of eccrine sweat glands with keratinocytes, we questioned whether the metabolic changes in sweat EVs may mirror the responses of keratinocytes upon heat exposure. To this, we exposed HaCat, which were maintained in low (mimicking healthy condition) and high glucose (mimicking diabetes condition) to acute (90 min), chronic (48 h), and repetitive heat exposure at 40 ⁰C. Through conducting a set of experiments including a targeted metabolomics approach, Greiss assay, western blotting analysis, and electron microscopy studies. The data demonstrate that heat exposure results in substantial changes of metabolite levels belonging to amino acids, pyrimidine metabolism, and glycolysis pathways in high glucose maintained HaCat cells when compared to those noted in low glucose condition. Exploring the molecular mechanisms through which heat exposure may impact the metabolic composition in keratinocytes, our discoveries highlight nitric oxide (NO) as a novel biomarker that the level is correlated with heat duration and frequency. Furthermore, data reveal that the HSP-70 protein levels and mitochondrial morphology are consequently altered. This study provides evidence of shared metabolic alterations in keratinocytes and sweat EVs collected from clinical study and proposes, for the first time, NO as a novel biomarker for monitoring changes in health and diabetes upon heat exposure.

In many industrial, automotive, and aerospace applications, electro-mechanical systems are subjected to random vibration excitations, and the most critical components are required to undergo qualification tests to verify their suitability. Measured field data are commonly considered as reference for the synthesis of random stationary signals used as shaker input excitations in laboratory tests. For the most popular procedures of random-control testing, the user sets the input profiles in terms of power spectral density (PSD) associated with randomized phases generated by the shaker controller to finally provide the physical motion. As a result, the overall probability distribution of the test signal tends toward Gaussian, whereas many real-life random excitations prove non-Gaussian due to distinctive bursts and peaks. The quantitative estimate of the number and amplitudes of peaks present in a certain signal is usually made through the statistical parameter known as kurtosis. The so-called kurtosis control methods presented in the literature are conceived to perform qualification tests with random and non-Gaussian vibration excitations. In this paper, two novel algorithms able to synthesize shaker input signals for random-control testing with prescribed PSD and kurtosis value are proposed, and the results of their application are comparatively discussed to assess their effectiveness and potentialities in different kinds of qualification testing, including accelerated fatigue-life tests.

Image fusion is the process of combining multiple input images from single or multiple imaging modalities into a fused image, which is expected to be more informative for human or machine perception as compared to any of the input images. In this paper, we propose a novel method based on deep learning for fusing infrared images and visible images, named the LBP-based proportional input generative adversarial network (LPGAN). In the image fusion task, the preservation of structural similarity and image gradient information is contradictory, and it is difficult for both to achieve good performance at the same time. To solve this problem, we innovatively introduce Local Binary Patterns (LBP) into Generative Adversarial Networks (GANs), which effectively utilize the texture features of the source images, so that the network has stronger feature extraction ability and anti-interference ability. In the feature extraction stage, we introduce a pseudo-siamese network for the generator to extract the detailed features and the contrast features. At the same time, considering the characteristic distribution of different modal images, we propose a 1:4 scale input mode. Extensive experiments on the publicly available TNO dataset and CVC14 dataset show that the proposed method achieves the state-of-the-art performance. We also test the universality of LPGAN through the fusion of RGB and infrared images on the RoadScene dataset. In addition, LPGAN is applied to multi-spectral remote sensing image fusion. Both qualitative and quantitative experiments demonstrate that our LPGAN can not only achieve good structural similarity, but also retain rich detailed information.

Based on Venturini method, it is in favor of the modulation technique for controlling the matrix converter due to only use of the comparison between the duty cycles in time domain and the triangular carrier wave for generating the gating signals and the achievable voltage ratio between fundamental output magnitude and fundamental input magnitude to 0.866. However, even with simple modulation method and achieving maximum fundamental output magnitude, the possible input voltage unbalance conditions accordingly influence on the output performances (more reduction and distortion). Thus, a modified Venturini modulation method is presented in this paper, in order to solve the problems of unbalanced input voltage conditions on the matrix converter performances. The proposed strategy is to satisfy the desirable feature of the duty cycle modulating waves, as generated in the event of normal situation. Up to this approach, it can support either single-phase condition or two-phase condition. Performance of the proposed control strategy was verified by the simulated implementation in the MATLAB/Simulink software with showing good steady-state and dynamic operations.

This study presents the comparison of heat transfer capacity and pressure drop characteristics between a basic fin-tube heat exchanger and a modified heat exchanger with the structural change of branch tubes and coiled turbulators. All experiments were carried out using an air-enthalpy type calorimeter based on the method described in ASHRAE standards, under heat exchanger experimental conditions. 14 different kinds of heat exchangers were used for the experiment. Cooling and heating capacities of the turbulator heat exchanger were excellent, compared to the basic one. As the insertion ratio of the coiled turbulator and the number of row increased, the heat transfer performance increased. However, the capacity per unit area was more effective in 4 rows than 6 rows, and the cooling performance of the 6 row turbulator heat exchanger (100% turbulator insert ratio) was down to about 6% than that of 4 row one. As the water flow rate and the turbulator insertion ratio increased, the pressure drop of the water side increased. This trend was more pronounced in 6 rows. In the cooling condition, the pressure drop on the air side was slightly increased due to the generation of condensed water, but was insignificant under the heating condition. The power consumption of the pump was more affected by the water flow rate than the coiled turbulator. The equivalent hydraulic diameter of a tube by the turbulator was reduced and then the heat transfer performance was improved. Thus, the tube diameter was smaller, the heat flux was better.

The purpose of this study is to propose a consecutive manufacturing process system to secure the productivity of excellent STKN540B steel tube in the respect of economy and safety as the supporting material for mega structures such as building, bridge and ship. The components of consecutive manufacturing are press-bending, orbital auto welding and steel tube correction. By using STKN540B a high-strength steel material with low yield point that requires a special manufacturing process unlike other steel materials, an actual tube manufacturing is carried out at each stage in this experimental study. With this, the quality of steel tube and the efficiency of the manufacturing process are analyzed to draw out some points to improve in the future.

The objective of this research is to develop an experimental-theoretical analysis about the influence of the cooling medium and the geometry of the welding bead profile in fatigue life and associated parameters with structural integrity of welded joints. A welded joint with cruciform geometry is considered using SMAW, plates in structural steel ASTM A36 HR of 8 mm of thickness and E6013 electrode input. A three-dimensional computational model of the cruciform joint was created using the finite element method. For this model, the surface undulation of the cord and differentiation in the mechanical properties of the fusion zone were considered, the heat-affected zone (HAZ) and base material, respectively. In addition, an initial residual stress field which was established experimentally was considered. The results were a set of analytical expressions for the weld magnification factor Mk. It was found that values for the latter decrease markedly in function of the intensity of the cooling medium used in the post welding cooling phase, mainly due to the effect of the residual compressive stresses. The obtained models of behavior of the weld magnification factor are compared with the results from other researchers with some small differences, mainly due to the inclusion of the cooling effect of the post weld and the variation of the leg of the weld bead. The obtained analytical equations in the present research for Mk can be used in management models of life and structural integrity for this type of welded joint.

Cladding is typically used to protect components from wear and corrosion while also improving the aesthetic value and reliability of the substrate. The cladding process induces significant residual stresses due to the temperature difference between the substrate and the clad layer. However, these residual stresses could be effectively utilized by modifying processes and geometrical parameters. This paper introduces a novel methodology for using the weld-cladding process as a cost-effective alternative to various existing reinforcement techniques. The numerical analyses are performed to maximize the reinforcement of a cylindrical tool. The investigation of how the weld cladding develops compressive stresses on the specimen in response to a change in the weld beads and the welding sequence is presented. For the benchmark shape, experimental verification of the numerical model is performed. The impact of the distance between the weld beads and the effect of the tool diameter is numerically investigated. Furthermore, the variation in compressive stresses due to temperature fluctuations during the extrusion process has been evaluated. The results showed that adequate compressive stresses are generated on the welded parts through the cladding process after cooling. Hence, the targeted reinforcement of the substrate can be achieved by optimizing the welding sequence and process parameters.

In laser joining of copper (Cu) and aluminum (Al) sheets, the Al sheet is widely chosen as the top surface for laser irradiation because of increased absorption of laser beam and lower melting temperature of Al in contrast to Cu. This research focus on welding from Cu side to Al sheet. The main objective of irradiating the laser beam from the copper side (Cu on top) is to exploit higher solubility of Al in Cu. A significantly lower laser power can be used with 515 nm laser in comparison to 1030 nm. In addition to low laser power, a stable welding is obtained with 515 nm. Because of this advantage, 515 nm is selected for the current research. By fusion of Cu and Al the two sheet metals are welded, with presence of beneficial Cu solid solution phase and Al+Al2Cu in the joint with the brittle phases intermixed between the ductile phase. Therefore the mixed composition strengthens the joint. However excessive mixing leads to formation of more detrimental phases and less ductile phases. Therefore optimum mixing must be maintained. Energy dispersive X-ray spectroscopy (EDS) analysis indicate that large amount of beneficial Cu solid solution and Al rich phases is formed in the strong joint. From the tensile shear test for a strong joint, fracture is obtained on the heat-affected zone (HAZ) of Al. Therefore the key for welding from copper side is to have optimum melt with beneficial phases like Cu and Al+ Al2Cu and the detrimental phases intermixed between the ductile phases

While the majority of previous studies assessing pain-related variables in psychopaths used electric shocks, little is known about the effectiveness of alternative pain-inducing methods to increase emotional responses such as fear and anxiety. A small sample of healthy undergraduate men (N = 15) was recruited to assess the effectiveness of a heat stimulus to induce pain in an immediate versus delayed punishment paradigm. Although pain catastrophizing, anxiety, and threat of pain did not increase throughout the experiment, participants experienced a significant increase of fear of pain and pain intensity, indicating that the heat stimulus was effective in inducing pain. Furthermore, subjects were slower in initiating the pain stimulus during the first five trials, but no time difference was found during the 15 remaining trials. No correlation was found between psychopathic traits and pain-related variables, with the exception of inconsistent results within the Fearless Dominance factor. Findings are discussed in terms of improvement for a larger scale study involving psychopathic individuals.

The plate fin heat exchanger is the compact heat exchanger applied in many industries because of its high thermal performance. To enhance the heat transfer of plate fin heat exchanger in further, three new kinds of wavy plate fins, namely perforated wavy fin, staggered wavy fin and discontinuous wavy fin are proposed and investigated by CFD simulations. The effects of key design parameters, including that of waviness aspect ratios, perforation diameters, stagger ratios and breaking distance are investigated, respectively, with the Reynolds number changes from 500 to 4500. It is found that due to the swirl flow and efficient mixing of fluid, the perforation, serration and breaking techniques are beneficial for the enhancement of heat transfer compared to the traditional wavy fin. At the same time, serration is beneficial to reduce the friction factor, and the breaking technique can reduce heat transfer area as well as enhance heat transfer performance. Through the performance evaluation criteria, the staggered wavy fin has an advantage over the small waviness aspect ratio compared to the perforated wavy fin. The maximum performance evaluation criteria (PEC), as high as 1.24, can be obtained for the perforated wavy fin at the largest waviness aspect ratio.

This research concerns in to understand the link between urban heat and cool island, the Local Climatic Zones (LCZ) and atmospheric systems during the winter season in the city of Balneário Camboriú, Southern Brazil. To collect meteorological data on urban environmental, 11 permanent points in the Balneário Camboriú metropolitan region were installed. To understand the atmos-pheric systems operating in the region, a synoptic analysis of the dates was performed, and then, the LCZs map created for the city in World Urban Database and Acess Portal Tools was used to cor-relate the magnitudes of the heat and cool islands found in Balneário Camboriú in the winter period. The results indicate that the increasing verticalization with the construction of skyscrapers in Balneário Camboriú has a significant influence on local conditions for the occurrence of heat and cold islands. The findings indicate that LCZs with sparsely distributed buildings (LCZs 6, 8 and 9) and LCZs with dense vegetation (LCZ A) have lower intensity magnitudes of heat and cool con-ditions. The biggest magnitudes of heat and cool islands were reported in LCZs 1 and 3 during the timeframe. The synoptic analysis supports earlier researches that points to atmospheric stability (Anticyclonic domain) as a favorable atmospheric setting for the emergence of urban hear and coolness islands.

In this paper, the integrated performance of a modular biomass boiler with an existing industrial Rankine steam heat and power cycle and a supplementary supercritical-CO2 (sCO2) Brayton cycle is analyzed. The aim is to leverage the high efficiency supplementary sCO2 cycle to increase net generation and energy efficiency from the existing biomass boiler. Two sCO2 heater configurations situated within the flue gas flow path are investigated, namely a single convective-dominant heater, and a dual heater configuration with a radiative and a convective heater. A quasi-steady-state 1D model was developed to simulate the integrated cycle, including detailed component characteristics for the Rankine and Brayton cycles. The model solves the mass, energy, momentum, and species balance equations. The system is analyzed for three cases: (i) the existing Rankine cycle without the sCO2 integration, (ii) with the single convective-dominant sCO2 heater configuration, and (iii) the dual sCO2 heater configuration. The results show the required rate of overfiring for the sCO2 configurations, with a 15.3% increase in fuel flowrate resulting in an additional 21.2% in net power output. The model quantifies the impact of the sCO2 heaters, with reduced heat uptakes for downstream boiler heat exchangers. Furnace water wall heat uptake increased due to overfiring, offsetting the reduced heat uptakes at downstream evaporative heat exchangers. The dual configuration has more impact on Rankine cycle operation due to the radiative sCO2 heater placement in front of the second superheater, absorbing some of the direct radiation from the furnace.

Three-phase to single-phase matrix converter (TSMC) is used as the transmitter for transient electromagnetic method (TEM) instrument, instead of an AC-DC converter and an H-bridge inverter. The transmitter produces excitation current for primary field. The output current has a waveform with a bipolar square of half duty cycle, which is required by TEM. The space vector PWM based on input currents is discussed in detail. The control method of input power factor is proposed for TSMC. The simulation model of TSMC is established and the simulations of different conditions are completed. The simulation results show the controllability of the input power factor is illustrated.

The welding and construction processes of H-type thick-plate-bridge steel involve complex multi-pass welding processes, which is difficulty to ensure its welding performance. Accordingly, it is crucial to explore the inherent correlation among the welding processes parameters and welding quality, and applied it into the welding robots, eliminating the instability from manual welding. In order to improve the welding quality, the GMAW (Gas Metal Arc Welding) welding process parameters are simulated using the Q345qD bridge steel flat joint model. Four welds with X-shaped grooves are designed to optimize the parameters of welding current, welding voltage, and welding speed. The optimal welding process parameters are investigated through thermal-elastic-plastic simulation analysis and experimental verification. The results indicate that when the welding current is set to 230A, the welding voltage to 32V, and the welding speed to 0.003m/s, the maximum deformation of the welded plate is 0.52mm, with a maximum welding residual stress of 345MPa. Both the simulation results of multi-pass welding and experimental tests meet the welding requirements, as they show no excessive stress or strain. These parameters can be applied into building large steel frame bridges with welding robots, improving the quality of welded joints.

A numerical model was developed for predicting the bead geometry and microstructure in Laser Beam Welding of 2 mm thickness Inconel 718 sheets. The experiments were carried out with a 1 kW maximum power fiber laser coupled with a galvanometric scanner. Wobble strategy was employed for sweeping 1 mm wide circular areas for creating the weld seams and a specific tooling was manufactured for supplying protective Argon gas during the welding process. The numerical model takes into account both the laser beam absorption and the melt-pool fluid movement along the bead section, resulting in a weld geometry that depends on the process input parameters, such as feed rate and laser power. The microstructure of the beads was also estimated based on the cooling rate of the material. Features as bead upper and bottom final shapes, weld penetration and dendritic arm spacing were numerically and experimentally analyzed and discussed. The results given by the numerical analysis agree with the tests, making the model a robust predictive tool.

Surfing is a growing, high participation recreational and competitive activity. It is relatively unique being performed on, in, and through water with a range of temperatures. In other sports, warm-up and heat retention have proved useful at augmenting performance and ameliorating injury risk. Little work has been done examining this in surfing. The purpose of this work was to measure thermal profiles in surfers with and without warm-up and passive heat retention, and secondarily to assess any potential influence on free surfing. A repeated measures pre- and post- design was adopted whereby participants surfed in an artificial wave pool following an active warm-up combined with passive heat retention (experimental condition), and after no warm-up (control). Core body temperature was measured both occasions. Our results showed a clear advantage to body temperature for the experimental condition versus control. Both groups showed a warm-up effect in the water itself, presumably due to further activity (e.g. paddling) and wetsuit properties. Finally, performance trended to being superior following warm-up. We conclude, body warmth in surfers may be facilitated by an active warm-up and passive heat retention. In free surfing this is associated with a trend towards better performance; it may also reduce injury risk.

Heat using behavior has a large impact on in heating energy in heat metering system, and therefore a better understanding can assist in behavior guidance to reduce energy. To understand the current situation of indoor thermal environment and heat using behavior for heat metering households in northern China, including adjusting heating end valves and operating windows, 30 households were measured and surveyed. The factors influencing heat using behavior, including outdoor and indoor environmental parameters and time of the day, were analyzed. The results are :1) Thermal neutral temperature for heat metering households is relatively high, up to 24.5℃; 2) The heat using behavior of households is lack of rationality: low proportion of active households; high indoor temperature setting; more frequency of window opening. Improving indoor comfort is the main reason for households to adjust the heating end valve, and only 7.15% of households have considered the economic benefits brought by adjusting the valve. " Thermostat control valve does not work" is the main reason for households without adjustment; 3) Time of the day and indoor temperature affect active households’ willingness to adjusting heating end valve. Time of the day, indoor temperature and outdoor temperature have impacts on opening window during heating period.

Battery-powered electric vehicles (EVs) have emerged as an environmentally friendly and efficient alternative to traditional internal combustion engine vehicles, while their single-charge driving distances under cold conditions are significantly limited due to the high energy consumption of heating systems. Heat pumps can provide an effective heating solution for EVs, but their coefficient of performance (COP) is hampered by heat transfer deterioration due to frost accumulation. This study proposes a solution to this issue by introducing a microchannel heat exchanger (MHE) with superhydrophobic surface treatment (SHST) as a heat pump evaporator. A computational-fluid-dynamics MHE model and a dynamic heat pump model are developed and rigorously validated to examine the detrimental impact of frost accumulation on heat transfer, airflow resistance, and heat pump performance. When the frost layer thickness is 0.8 mm at a given air-side velocity of 1.0 m/s, the air-side heat transfer coefficient can be reduced by about 75%, and the air-side pressure drop sharply increases by 28.4 times. As frost thickness increases from 0 to 0.8 mm, the heating effect drops from 3.97 to 1.82 kW, and the system COP declines from 3.17 to 2.30. Experimental results show that the frost thickness of the MHE with SHST reaches approximately 0.4 mm after 30 minutes, compared to that of 0.8 mm of the MHE without SHST, illustrating the defrosting capability of the superhydrophobic coating. The study concludes by comparing the performance of various heating methods in EVs to highlight the advantages of SHST technology. As compared to traditional heat pumps, the power consumption of the proposed system is reduced by 48.7% due to the defrosting capability of the SHST. Moreover, the single-charge driving distance is extended to 327.27 km, an improvement of 8.99% over the heat pump without SHST.

The study aimed to determine the effect of heat stress (HS) on reproductive parameters [calving to first service (CTFS) and first service conception rate (FSCR)] and general physiological responses [rectal temperature (RT) and respiratory rate (RR)] in tropical Holstein Friesian dairy cows raised in Ratchaburi province, Thailand. Cows were divided into a moderate HS (n = 22) and a mild HS (n = 22) group. Cycling cows were detected and injected with PGF2α at the beginning of the experimental period. Reproductive and physiological parameters were recorded. The average temperature humidity indices experienced by the cows were 80.67 ± 0.79 and 77.81 ± 1.09 for the moderate and mild HS groups, respectively. Cows showed significantly lower RT and RR in the mild (38.47 ± 0.21°C and 41.04 ± 4.55 bpm, respectively) than in the moderate HS group (38.87 ± 0.15°C and 51.17 ± 10.52 bpm). Under mild HS, cows showed a better response to injection of PGF2α than those under moderate HS. The percentage of cows that ovulated after being induced by PGF2α and showed estrus signs was higher in the mild than the moderate HS groups (54.55% versus 18.18%). Furthermore, the FSCR of cows under mild HS tended to be higher than in the moderate HS group (54.55 % and 42.11%, respectively), while the average CTFS interval was significantly shorter under mild than moderate HS (69.47 ± 18.18 and 84.60 ± 27.68, respectively). These results indicate that HS impairs reproductive performance in cross-bred Holstein cows, especially in moderate HS conditions.

This paper investigates the use of contactless power ultrasonic excitation to decrease the electrical impedance of the weld in laser welding. The literature extensively documents the impact of em-ploying contact power ultrasonic excitation on the microstructure morphology and refinement of grain in the weld. This study involves characterizing an industrial High Power Ultrasound Transducer (HPUT) by determining the optimal distance and angle for contactless excitation of the fusion zone in the weld, aiming to achieve the maximum amplitude. Subsequently, the transducer is integrated into the laser welding system, resulting in the creation of an ultrasonic-assisted welding system. To find the improvement due to the contactless vibration assistance, the welding area was char-acterised by an impedance ohmmeter device. The results indicate an approximately 6 % im-provement in the welding quality in terms of the impedance value, an important parameter for battery pack welding. In response to the issue of overheating in the industrial transducer during prolonged welding operations, an alternative transducer was proposed to overcome this challenge. Further investigations are carried out by the alternative transducer to find the effect of different wave types, namely, shear and compressional waves, on the welding quality. The contact vibration can excite the plate approximately 50 times higher in acceleration amplitude than contactless ex-citation. Nevertheless, enhancements of 10% and 6% are observed in the impedance value when utilising compressional and shear waves, respectively, as compared to the results obtained with contactless vibration.

Keyhole laser beam welding (LBW) of stainless steel sheets with a gap in between is numerically simulated with a three-dimensional, transient multi-physical model for laser material processing. At first, the model’s ability to reproduce experimental results on a relatively coarse computational mesh within reasonable computing time, so as to serve as process optimization tool, is presented. An example of process optimization, where a given set of weld seam quality criteria is fulfilled by iteratively optimizing a secondary laser beam, is shown. The relatively coarse mesh, in combination with a good model calibration to the experimental conditions, allows for sufficiently fast simulations to use this approach for optimization tasks. Finally, using a finer spatial and temporal discretization, the dynamic processes in the vicinity of the keyhole leading to the formation of pores are investigated. The physical phenomena predicted by the simulation are coherent with experimental observations found in literature.

The aim of this paper is to at first evaluate the influence of three key parameters including weld current, weld time and electrode force on nugget diameter and tensile strength in resistance projection welding. Then, a 2-D axis-symmetric finite element model is developed to simulate the projection welding and predict the nugget diameter. Finally, the FEM results are compared to experimental data to verify the simulation model and simulated results. In the finite element model, the temperature-dependent material properties were taken into account.

As an active device, air source heat pumps (ASHP) are widely used for heating and cooling in buildings. However, in cold regions, their efficiency decreases, and frost formation becomes a significant issue during winter. This paper proposes a new scheme that couples air source heat pumps with passive heating. By using software simulations and mathematical models, the new scheme is compared to traditional ASHP systems to analyze its heating performance in rural homes during winter in China’s cold regions. According to the simulation and calculation analysis, on the coldest day of winter, the coupling scheme can provide approximately 99.41kWh of heat to the interior, surpassing the 86.67kWh required to maintain an indoor temperature of 20℃. The system’s power consumption is 36.96 kWh, which is 66.88% lower than that of traditional heat pump heating. The study shows that a coupled system of air source heat pumps and passive heating has better heating performance in cold regions. By incorporating phase change materials and heat storage media to address the shortage of solar energy at night, the system can meet the heating needs throughout the entire day.

Sweat rate and electrolyte losses have a large inter-individual variability, a personalized approach to hydration can overcome this issue to meet an individual’s needs. This study aimed to investigate the effects of personalized hydration strategy (PHS) on fluid balance and intermittent exercise performance. Twelve participants conducted 11 laboratory visits including a VO2max test and two 5-day trial arms under normothermic (NOR) or hyperthermic (HYP) environmental conditions. Each arm began with 3-day of familiarization exercise following by two random exercise trials with a either PHS or control (CON). Then, participants crossed-over to the second arm for: NOR+PHS, NOR+CON, HYP+PHS, and HYP+CON. The PHS was prescribed according to participants’ fluid and sweat sodium losses. CON drank ad-libitum of commercially-available electrolyte solution. Exercise trials consisted of two phases: 1) 45min constant workload; 2) high-intensity intermittent exercise (HIIT) until exhaustion. PHS had a significantly greater fluid intake compared to CON. HYP+CON produced the lowest sweat sodium concentration. HYP+PHS had a lower thirst perception and a longer HIIT compared to HYP+CON. Thus, PHS reinforces fluid intake and successfully optimizes hydration status, regardless of environmental conditions. PHS may be or is an important factor to preventing negative physiological consequences during high-intensity exercise in the heat.

Many microbes live in habitats below their optimum temperature. Retention of metabolic heat by aggregation or insulation would boost growth. Generation of excess metabolic heat may also provide benefit. A cell that makes excess metabolic heat pays the cost of production, whereas the benefit may be shared by neighbors within a zone of local heat capture. Metabolic heat as a shareable public good raises interesting questions about conflict and cooperation of heat production and capture. Metabolic heat may also be deployed as a weapon. Species with greater thermotolerance gain by raising local temperature to outcompete less thermotolerant taxa. Metabolic heat may provide defense against bacteriophage attack, by analogy with fever in vertebrates. This article outlines the theory of metabolic heat in microbial conflict and cooperation, presenting several predictions for future study.

The identification of the most rockfall-prone areas is the first step of the risk assessment procedure. In the case of land and urban planning, hazard and risk analyses involve large portions of territory and thus preliminary methods are preferred to define specific zones where more detailed computations are needed. To reach this goal, we developed the QGIS-based plugin QPROTO, able to quantitatively compute rockfall time-independent hazard over a three-dimensional topography on the basis of the Cone Method. This is obtained by combining kinetic energy, passing frequency and detachment propensity of each rockfall source. QPROTO requires the definition of few angles (i.e., the energy angle ϕ_p and the lateral angle α) that should take into account all the phenomena occurring during the complex block movement along the slope. The outputs of the plugin are a series of raster maps reporting the invasion zones and the quantification of both the susceptibility and the hazard. In this paper, we propose a method to relate these angles to some characteristics of the block (volume and shape) and the slope (inclination, forest density), to provide QPROTO users with a tool for estimating the input parameters. The results are validated on a series of case studies belonging to the North Western Italian Alps.

For the generation of representative volume elements a statistical description of the relevant parameters is necessary. These parameters usually describe the geometric structure of a single grain. Commonly, parameters like area, aspect ratio and slope of the grain relative to the rolling direction are applied. However, usually simple distribution functions like log normal or gamma distribution are used. Yet, these do not take the interdependencies between the microstructural parameters into account. To fully describe any metallic microstructure though, these interdependencies between the singular parameters need to be accounted for. To accomplish this representation, a machine learning approach was applied in this study. By implementing a Wasserstein generative adversarial network, the distribution, as well as the interdependencies could accurately be described. A validation scheme was applied to verify the excellent match between microstructure input data and synthetically generated output data.

This study examines the effects of particle size and heat pipe angle on the thermal effectiveness of a cylindrical screen mesh heat pipe using silver nanoparticles as the test substance. The experiment investigates three different particle sizes (30nm, 50nm, and 80nm) and four different heat pipe angles (0°, 45°, 60°, and 90°) on the heat transmission characteristics of the heat pipe. The results show that the thermal conductivity of the heat pipe increased with an increase in heat pipe angle for all particle sizes, with the highest thermal conductivity attained at a 90° heat pipe angle. Furthermore, the thermal resistance of the heat pipe decreased as the particle size decreased for all heat pipe angles. The thermal conductivity measurements of the particle sizes - 30, 50, and 80 nm - were 250 W/mK, 200 W/mK, and 150 W/mK, respectively. The heat transfer coefficient values for particle sizes 30nm, 50nm, and 80nm were 5500 W/m2K, 4500 W/m2K, and 3500 W/m2K, respectively. The study also found that the heat transfer coefficient increased with increased heat pipe angle for all particle sizes, with the highest heat transfer coefficient obtained at a 90° heat pipe angle.

Under the increasingly severe global heat threat, continuous high temperature has far-reaching effects on plant growth and development and become a major constraint to crop production. The development of heat-resistant varieties has become research hotspot in many fields, and it is also necessary to establish effective identification methods. In this study, twenty Brassica rapa varieties were selected to to investigate the physiological and biochemical characteristics under heat stress, explore the relationship between physiological response and the heat resistance mechanism, select some typical heat-resistant and heat-sensitive varieties. The effects of photosynthetic electron transfer and antioxidant pathway on heat resistance of Brassica rapa were identified. These findings will providing an important reference for the physiological regulation and identification method of high-temperature stress in plants.

Introduction: Heat is a kinetic process whereby energy flows from between two systems; hot-to-cold objects. In oro-dental implantology, conductive heat transfer/(or thermal stress) is a complex physical phenomenon to analyze and consider in treatment planning. Hence, ample research has attempted to measure heat-production to avoid over-heating during bone-cutting and -drilling for titanium (Ti) implant-site preparation and insertion, thereby preventing/minimizing early (as well as delayed) implant-related complications and failure. Objective: Given the low bone-thermal conductivity whereby heat generated by osteotomies is not effectively dissipated and tends to remain within the surrounding tissue (peri-implant), increasing the possibility of thermal-injury; this work attempts to obtain an exact analytical solution of the heat equation under exponential thermal-stress, modeling transient heat transfer and temperature changes in Ti implants upon hot-liquid intake. Materials and Methods: We investigate the impact of the material, the location point along implant length, and the exposure time of the thermal load on temperature changes. Results: Despite its simplicity, the presented solution contains all the physics and reproduces the key features obtained in previous numerical analyses studies. To the best of knowledge, this is the first introduction of the intrinsic time, a “proper” time that characterizes the geometry of the dental implant, where we show, mathematically and graphically, how the interplay between “proper” time and exposure time influences temperature changes in Ti implants, under the suitable initial and boundary conditions. Conclusions: This work aspires to accurately complement the overall clinical diagnostic and treatment plan for enhanced bone-implant interface, implant stability and success rates, whether for immediate or delayed loading strategies.

This paper presents a comparative study of heat transfer performance of lattice structured heat sinks. 20 different unit cells were chosen and heat sinks were modelled in nTop with constant unit cell size. Al 6061 alloy was chosen for analysis due to its good thermal conductivity, low weight, low cost, and high strength. Steady state thermal analysis was performed using ANSYS with constant input parameters for all samples. Heat flux and temperature distribution within the heat sinks were analysed. The study aims to provide a comprehensive understanding of the thermal performance of lattice heat sink designs.

A sintered wick was formed in a heat pipe through the process of sintering a mixture of copper powder with particle sizes of 100㎛ and 200㎛, mixed with a pore-forming agent. On application to the heat pipes. The thermal resistance of heat pipes containing a sintered wick was calculated for different tilting angles (0°, 45°, and 90°) according to the type of powder, thickness of the sintered wick, and the filling ratio of the working fluid. The heat transfer efficiencies were evaluated through temperature tests. The capillary force, which is closely related to heat transfer efficiency, is determined by the effective pore radius resulting from the sintering of the copper powder. Furthermore, it was observed that the heat transfer performance of the heat pipe was at its best when the working fluid filling ratio was 30%. Additionally, the width of the wick was found to have a direct correlation with the heat transfer performance.