Wireless Powered Communication Networks (WPCN), which has attracted much attention of researchers, also been recently recommended in 5^th generation (5G) wireless networks. With the help of the WPCN, the reliability and battery life of wireless low-power devices can be improved. In this paper, we investigate throughput and ergodic capacity in WPCN-assisted amplify-and-forward (AF) relaying system, considering two transmission modes including delay-tolerant and delay-limited. As important achievement, we propose symmetric energy harvesting protocol, namely time power switching relaying (TPSR) in order to find maximal throughput. In particular, both time switching and power switching coefficients in this schemes are considered. Unlike most of the previous works, we further focus on impact of outdated channel state information (CSI) in this WPCN. In order to evaluate information processing efficiency, the performance can be substantially improved by optimally harvesting time and power coefficients of the received signal at relay node for energy and information extraction, and by deploying several scenarios. By deploying Monte Carlo simulation, it is confirmed that the system performance is more sensitive to CSI estimation error, noise variance, signal-to-noise ratio (SNR) and resulting in other reasonable computations of TPSR need be deployed to obtain QoS requirement.

Wireless Sensor Networks (WSN) is designed to collect information across a large number of limited battery sensor nodes. Therefore, it is important to minimize the energy consumption of each node, which leads to the extension of the network life. Our goal is to design an intelligent WSN that collects as much information as possible to process it intelligently. To achieve this goal, an agent has been migrated to each node in order to process the information and to cooperate with these neighboring nodes while Mobile Agents (MA) can be used to reduce information between nodes and send those to the base station (Sink). This work proposes to use communication architecture for wireless sensor networks based on the Multi Agent System (MAS) to ensure optimal information collection. The collaboration of these agents generates a simple message that summarizes the important information in order to transmit it by a mobile agent. To reduce the size of the MA, the nodes of the network have been grouped into sector. As for each MA, we have established an optimal itinerary, consuming a minimum amount of energy with the data aggregation efficiency in a minimum time. Successive simulations in large scale wireless sensor networks through the SINALGO simulator show the performance of our proposal, in terms of energy consumption and package delivery rate.

The monitoring of maternal and child health, using wearable devices made with wireless sensor technologies, is expected to reduce maternal and child death rates. Wireless sensor technologies have been used in wireless sensor networks to enable the acquisition of data for monitoring machines, smart cities, transportation, asset tracking, and tracking of human activity. Applications based on wireless body area network (WBAN) have been used in healthcare for measuring and monitoring of patient health and activity through integration with wearable devices. Wireless sensors used in WBAN can be cost-effective, enable remote availability, and can be integrated with electronic health record (EHR) management systems. Interoperability of WBAN sensor data with other linked data has the potential to improve health for all, including maternal and child health through the improvement of data access, data quality and healthcare access. This paper presents a survey of the state-of-the-art techniques for managing WBAN sensor data interoperability. The findings in this study will provide reliable support to enable policymakers and health care providers to take action to enhance the use of e-health to improve maternal-child health and reduce the mortality rates of women and children.

With the emergence of Advance Logistics, the logistics industry has witnessed significant advancements, leading to a greater reliance on intelligent technologies. These technologies play a crucial role in gathering and transmitting logistics data, but they also introduce security and privacy risks to logistics management systems. The sharing of customer-sensitive information among stakeholders for efficient operations becomes vulnerable to unauthorized access, thus compromising privacy. This, amongst others, is a critical problem that needs to be addressed. The unique features of a cryptographic hash function, including immutability, efficient verification, and anonymity, make it a transformative technology that has the potential to address the mentioned challenges in various sectors. This disruptive technology offers solutions by ensuring data integrity, enabling quick verification, and preserving privacy. The findings suggest that employing Cryptographic Hash Functions to share customer data among logistics partners offers robust protection against cyber-attacks. The proposed system guarantees asset security, and as demonstrated by the case study evaluation, exhibits strong resilience in safeguarding against various security and privacy threats. Although this study is significant, it does have limitations. One of these limitations is the considerable overlap between logistics research and supply chain management (SCM). While our focus was on logistics tasks, we did not extensively delve into the broader context of SCM

This paper investigates an Energy Neutral System using Micro Energy Harvesters for a Health Monitoring Wireless Sensor Node (HM-WSN). We have implemented HM-WSN consisting of a solar cell energy harvester, a Power Management Unit (PMU) and the ucontroller, sensor and transmitter acting as load. A battery extender and a switching logic circuit for sensor node is designed to evaluate the efficiency of the proposed system. The HM-WSN senses body temperature with improvement in lifetime of coincell. The HM-WSN is built using commercially available off the shelf (COTS components and consumes 47.2uW for data being updated every 134s. It can be operated for approximately 1.32 years only on a coincell. Furthermore, the HM-WSN can be operated with solar energy at 200lux, achieving 96.36 years with a combination of a coincell with an additional capacitor of 2.2mF. It attains 4.07 years to 16.87 years lifetime with the load capacitor varying from 1mF to 1.5mF at 350lux lighting condition. With the same ambient condition and a 2mF load capacitor, HM-WSN attains complete energy autonomy.

Wireless sensor networks (WSN) are mostly utilized in many applications. Indeed, WSN is composed of sensors to evaluate some physical phenomena. However, the information brought by the sensor still missed if we don't know the exact location of the event. Several localization algorithms have been proposed in order to locate the nodes in WSN. The localization algorithms are categorized into range-based and range-free techniques. The range-based techniques use either distance or time to calculate the coordinates of unknown nodes. Nevertheless, those kinds of techniques need some additional material in computation purpose. Therefore, range-based techniques present an expensive solution for positioning in WSN. Alternatively, range-free techniques may do the same task without involving additional material. But they don’t offer a high precision of localization in comparison with range-based techniques. DVHOP is the most popular range-free technique that uses the hop count method in the localization process. In this work, we propose an improvement of DVHOP localization algorithm to create three improved versions of this algorithm and we have achieved that by adopting two meta-heuristic (simulated annealing, particle swarm optimization) and FMINCON solver dedicated to the optimization in the field of WSN nodes localization. The experimental results obtained in this work show clearly the gain and the good impact of our proposition.

Wireless Sensor Networks (WSNs) is considered to be a promising research area since it entails sensing capabilities. WSNs are confronted by fabricated explosion injection attacks and in return results into draining of vitality on sensor nodes routing mainly because of increased capabilities in a broad range of applications where sensor nodes use a battery as the power source. In this paper, we reveal and claim a state-of-the-art model to minimize vitality depletion of nodes within the network in return increases network period to more realistic stretch. It is revealed that the main cause is vitality consumption unbalances in different parts of the network direct resulting from having a static sink. More still, the network nodes neighboring the sink insistently partake in progressing data of other nodes to the sink. Consequently, the network nodes are supplementarily subjected to untimely vitality exhaustion. This paper mainly provides a novel movable (mobile) fuzzy logic sink approach and an intelligent system like expect systems that are able to scrutinize network situation, and make the superlative choice for spreading the network period robotically.

Due to the renewed variation in government and political systems inside and outside countries, and with the high tariffs at borders, the latter have become an outlet for terrorism and smugglers. Therefore, each country seeks to develop its own protection system, and the technologies used in these systems vary according to the severity and the importance of the installations to be protected, it is found that some of them are expensive and unnecessary, but other have good and variable levels of efficiency. Consequently, the idea of designing a surveillance system that can monitor and control access becomes indispensable. In the same context, this work is of crucial strategic and geopolitical importance. It combines pre-existing alarm and monitoring methods and revolutionary Internet of Things (IoT) application products, of which Wireless Sensor Networks (WSN) and Optical Fiber Sensors (OFS) are part of this application. This article presents the distribution of wireless radar nodes accompanying with a Bragg fiber sensor to identify each rolling intruder incoming the zone to be monitored, from the determination of its speed, weight and wheelbase distance.

Water covers a greater part of the earth's surface. Even though we know very little about the underwater world as most parts of it remain unexplored. Oceans including other water bodies hold huge natural resources and also the aquatic lives. These are mostly unexplored and very few of those are known due to unsuited and hazardous environments for the human to explore. This vast underwater world can be monitored remotely from a distant location with much ease and less risk. To monitor water-bodies remotely in real-time, sensor networking has been playing a great role. It is needed to deploy a wireless sensor network over the volume which we want to surveil. For vast water bodies like oceans, rivers and large lakes, data is collected from the different heights of the water level which is sent to the surface sink. Unlike terrestrial communication, radio waves and other conventional mediums can't serve the purpose of underwater communication as they pose high attenuation and very reduced transmission range. Rather an acoustic medium can transmit data more efficiently and reliably in comparison to other mediums. To transmit data reliably from the bottom of the sea to the sinks at the surface, multi-hop communication is needed which must involve a certain scheme. For seabed to surface sink communication, leading researchers have proposed different routing protocols. The goal of these routing protocols is to make underwater communication more reliable, energy-efficient and delay efficient thus to improve the performance of the overall communication. This paper surveys the advancement and applications of the routing protocols which eventually helps in finding the most efficient routing protocol for the Underwater Wireless Sensor Network (UWSN).

Underwater wireless sensor networks (UWSNs) represent a specialized category of WSNs with versatile applications including acoustic monitoring, oil and gas exploration, and military surveillance. UWSNs face formidable challenges such as limited energy resources, extended propagation delays, and harsh conditions. Existing clustering and multi-hop routing protocols often unevenly distribute nodes geographically, causing network fragmentation and disproportionately draining the battery life of nodes near the sink due to higher data transmission demands. In this paper, we introduce an Energy-efficient Artificial Fish Swarm-based Clustering Protocol (EAFSCP), inspired by the collective behavior of fish swarms. EAFSCP is a decentralized clustering algorithm designed for acoustic monitoring in UWSNs. Its decentralized nature makes it particularly well-suited for large-scale UWSNs, where centralized algorithms may not be feasible. Through comprehensive comparisons with existing cluster-based routing protocols, our findings indicate that EAFSCP consistently outperforms them across multiple key performance metrics, including network lifetime, energy consumption, packet delivery ratio, packet loss rate, and throughput. According to the results, EAFSCP represents an effective clustering algorithm that enhances network performance, prolongs network lifespan by reducing energy consumption, promotes scalability, and provides valuable guidance for emergency response efforts.

Landslides are a frequent and recurrent problem in hilly regions of India and predicting them is always a challenging task. In this paper, an attempt was made to deal with this problem using advanced physical and numerical modeling methods. Detailed understanding of the initial slope failures is very interesting, and challenging at the same time, in the design and development of wireless sensor network based on early warning of landslide monitoring. A small scale physical model was developed to assess the instability through a sensor network with variable rain fall intensity. This was achieved by increasing the simulated rain water flow intensity in different time spans (dry condition, at t=0 to t= 30 min, 0.5 mm/min at t=30 to t= 60 min, 0.75 mm/min at t=60 to t=91 min and 1 mm/min at t=91 to t= 120 min). The water level and movement in the slope was recorded by rainfall sensor, vibration sensor, soil moisture sensor and a digital camera. The following changes were observed during the slope failure: a) movement of small particles at top of the slope; b) initial failure of medium size soil particle; c) scouring of soil mass; d) whole slope collapse. The obtained results clearly indicated the superiority and effectiveness of the proposed system in providing a factor of safety for the progressive slope.

An existing power grid is going through a massive transformation. Smart grid technology is a radical approach for improvisation in prevailing power grid. Integration of electrical and communication infrastructure is inevitable for the deployment of Smart grid network. Smart grid technology is characterized by full duplex communication, automatic metering infrastructure, renewable energy integration, distribution automation and complete monitoring and control of entire power grid. Wireless sensor networks (WSNs) are small micro electrical mechanical systems which are accomplished to collect and communicate the data from surroundings. WSNs can be used for monitoring and control of smart grid assets. Security of wireless sensor based communication network is a major concern for researchers and developers. The limited processing capabilities of wireless sensor networks make them more vulnerable to cyber-attacks. The countermeasures against cyber-attacks must be less complex with an ability to offer confidentiality, data readiness and integrity. The address oriented design and development approach for usual communication network requires a paradigm shift to design data oriented WSN architecture. WSN security is an inevitable part of smart grid cyber security. This paper is expected to serve as a comprehensive assessment and analysis of communication standards, cyber security issues and solutions for WSN based smart grid infrastructure.

Surveillance along the Kenya-Somalia border has been a big challenge that has continuously puzzled the security personnel, due to insurgency of armed militia Al-Shabaab from Somalia , the Kenyan government proposed construction of a barrier wall. This project developed a low cost wireless sensor network surveillance system to be deployed along the Kenya-Somalia border. The research study utilized two PIR sensor for detecting human intrusion, one motion is detected the sensor transmit the data via an Xbee module. Arduino microcontroller was used to process the data collected by the sensor before transmission. The system developed has two units, the Transmitter unit and a User Graphic interface running on Tuna Term software that displays the received data. During testing, the prototype system detected human intrusion, using the Arduino serial monitor the results were displayed before being package for transmission.

As Heterogeneous Wireless Sensor Network (HWSN) fulfill the requirements of researchers in the design of real life application to resolve the issues of unattended problem. But, the main constraint face by researchers is energy source available with sensor nodes. To prolong the life of sensor nodes and hence HWSN, it is necessary to design energy efficient operational schemes. One of the most suitable routing scheme is clustering approach, which improves stability and hence enhances performance parameters of HWSN. A novel solution proposed in this article is to design energy efficient clustering protocol for HWSN, to enhance performance parameters by EECPEP-HWSN. Propose protocol is designed with three level nodes namely normal, advance and super node respectively. In clustering process, for selection of cluster head we consider three parameters available with sensor node at run time, i.e., initial energy, hop count and residual energy. This protocol enhance the energy efficiency of HWSN, it improves performance parameters in the form of enhance energy remain in the network, force to enhance stability period, prolong lifetime and hence higher throughput. It is been found that proposed protocol outperforms than LEACH, DEEC and SEP with about 188, 150 and 141 percent respectively.

Continuous object tracking in WSNs, such as monitoring of mud-rock flows, forest fires etc., is a challenging task due to characteristic nature of continuous objects. They can appear randomly in the network field, move continuously, and can change in size and shape. Monitoring such objects in real-time generally require tremendous amount of messaging between sensor nodes to synergistically estimate object’s movement and track its location. In this paper, we propose a novel twofold-sink mechanism, comprising of a mobile and a static sink node. Both sink nodes gather information about boundary sensor nodes, which is then used to uniformly distribute energy consumption across all network nodes, thus helping in saving residual energy of network nodes. Numerous object tracking schemes, using mobile sink, have been proposed in the literature. However, existing schemes employing mobile sink cannot be applied to track continuous objects, because of momentous variation of network topology. Therefore, we present in this paper a mechanism, transformed from K-means algorithm, to find the best sensing location of the mobile sink node. It helps to reduce transmission load on the intermediate network nodes situated between static sink node and the ordinary network sensing nodes. The simulation results show that the proposed scheme can distinctly improve life time of the network, compared to one-sink protocol employed in continuous object tracking.

Underwater acoustic sensor network (UASN) plays a crucial role in collecting real-time data from remote areas of the ocean. However, deploying the UASN is a challenging problem due to the harsh environment and high deployment cost. Therefore, it is essential to design an appropriate routing protocol to effectively address the issues of routing void, packet delivery delay, and energy utilization. In this paper, an adaptive support-vector-machine-based routing (ASVMR) protocol is proposed for the UASN to prolong the network lifetime and reduce the end-to-end packet delivery delay. The proposed protocol employs a distributed routing approach that dynamically optimizes the routing path in real-time by considering four types of node state information. Moreover, the ASVMR protocol establishes a "routing vector" spanning from the current node to the sink node, and selects a suitable pipe radius according to the packet delivery ratio (PDR). In addition, the ASVMR protocol incorporates future states of sensor nodes into the decision-making process, along with the adoption of a waiting time mechanism and routing void recovery mechanism. Extensive simulation results demonstrate that the proposed ASVMR protocol performs well, in terms of the PDR, the hop count, the end-to-end delay, and the energy efficiency in dynamic underwater environments.

An innovative wireless sensor network (WSN) based on Ultra-Wide Band (UWB) technology for 3D accurate superficial monitoring of ground deformations, as landslides and subsidence, is proposed. The system has been designed and developed as part of an European Life+ project, called Wi-GIM (Wireless Sensor Network for Ground Instability Monitoring). The details of the architecture, the localization via wireless technology and data processing protocols are described. The flexibility and accuracy achieved by the UWB two-way ranging technique is analysed and compared with the traditional systems, such as robotic total stations (RTSs), Ground-based Interferometric Synthetic Aperture Radar (GB-InSAR), highlighting the pros and cons of the UWB solution to detect the surface movements. An extensive field trial campaign allows the validation of the system and the analysis of its sensitivity to different factors (e.g., sensor nodes inter-visibility, effects of the temperature, etc.). The Wi-GIM system represents a promising solution for landslide monitoring and it can be adopted in conjunction with traditional systems or as an alternative in areas where the available resources are inadequate. The versatility, easy/fast deployment and cost-effectiveness, together with the good accuracy, make the Wi-GIM system a possible solution for municipalities that cannot afford expensive/complex systems to monitor potential landslides in their territory.

With the integrated development of the Internet, wireless sensor technology, cloud computing, and mobile Internet, there has been a lot of attention given to research about and applications of the Internet of Things. A Wireless Sensor Network (WSN) is one of the important information technologies in the Internet of Things; it integrates multi-technology to detect and gather information in a network environment by mutual cooperation, using a variety of methods to process and analyze data, implement awareness, and perform tests. This paper mainly researches the localization algorithm of sensor nodes in a wireless sensor network. Firstly, a multi-granularity region partition is proposed to divide the location region. In the range-based method, the RSSI (Received Signal Strength indicator, RSSI) is used to estimate distance. The optimal RSSI value is computed by the Gaussian fitting method. Furthermore, a Voronoi diagram is characterized by the use of dividing region. Rach anchor node is regarded as the center of each region; the whole position region is divided into several regions and the sub-region of neighboring nodes is combined into triangles while the unknown node is locked in the ultimate area. Secondly, the multi-granularity regional division and Lagrange multiplier method are used to calculate the final coordinates. Because nodes are influenced by many factors in the practical application, two kinds of positioning methods are designed: the unknown node is in the positioning unit or not. When the unknown node is on the side of the positioning unit, we use the method of vector similarity. Moreover, we use the centroid algorithm to calculate the ultimate coordinates of unknown node. When the unknown node is not on the side of the positioning unit, we establish a Lagrange equation containing the constraint condition to calculate the first coordinates. Furthermore, we use the Taylor expansion formula to correct the coordinates of the unknown node. In addition, this localization method has been validated by establishing the real environment.

To enhance industrial competitiveness and increase productivity, every country has strived to create a smart factory by introducing technologies such as Internet of Things, big data and artificial intelligence into production line and build cyber-physical system for the purpose of promoting manufacturing efficiency. For mission assignment, production line management or manufacturing field analysis, the location information of employee, machine and material is very essential. To promote manufacturing efficiency, of course, the location information became more important. A Bluetooth low energy (BLE) positioning system for the manufacturing is developed in this research. A "Tag tracking" mechanism is addressed and adopted, which uses Beacon to catch the location information and a BLE receiver is also used to receive the broadcasting information from Beacon. The position information from the BLE receiver will be compared with the data in the database for calculating the location of the target. The status of the target may also be obtained by using the data from the BLE receiver. Comparing with the mobile device, this method can reduce energy consumption and make the maintenance simple and easy. In the real applications, the target may not be limited to human. The "Regional label positioning technology" is also investigated in this research. Defining a suitable zone location and arranging BLE receiver location, and positioning analysis theory are the key factors included in this developed technology. The developed system will be tested for real industry applications. The test results show that the feasibility of this technology.

Underwater Wireless Sensor Networks (UWSN) enables various oceanic applications which require effective packet transmission. In this case, sparse node distribution, dynamic network topology and inappropriate selection of relay nodes cause void holes. Addressing this problem, we present a Relay based Void Hole Prevention and Repair protocol (ReVOHPR) by multiple Autonomous Underwater Vehicles (AUV) for UWSN. ReVOHPR efficiently identifies and avoids void holes and trap relay nodes to avoid it. ReVOHPR adopts the following operations as Ocean Depth (levels) based Equal Cluster Formation, Dynamic Sleep Scheduling, Virtual Graph based Routing, and Relay Assisted Void Hole Repair. For energy efficient cluster forming, Entropy based Eligibility Ranking (E2R) is presented which elects stable cluster heads (CHs). Then, dynamic sleep scheduling is implemented Dynamic Kernel Kalman Filter (DK2F) algorithm in which Sleep and Active modes based on the nodes current status. Inter Cluster Routing is performed by maximum matching nodes which selects by Dual criteria and also data transmitted to AUV. Finally, void holes are detected and repair by Bi-Criteria Mayfly Optimization (BiCMO) algorithm. The BiCMO focuses on reducing the number of holes, data packet loss and maximizes Quality of Service (QoS) and energy efficiency of the networks. This protocol is timely deal with node failures in packet transmission via multi-hop routing. Simulation is implemented by NS3 (AquaSim module) simulator that evaluates the performance in network simulation for following metrics as average energy consumption, delay, packet delivery rate and throughput.

The integration of Wireless Sensor Networks (WSNs) into agricultural areas has had a significant impact and has provided new, more complex, efficient, and structured solutions for enhancing crop production. This research reviews the role of Wireless Sensor Networks (WSNs) in monitoring the macro-nutrient content of plants. The review study focuses on identifying the types of sensors used to measure macro-nutrients, determining sensor placement within agricultural areas, implementing wireless technology for sensor communication, and selecting device transmission intervals and ratings. The study of NPK (Nitrogen, Phosphorus, Potassium) monitoring using sensor technology in precision agriculture is of high significance in efforts to improve agricultural productivity and efficiency. In addition to fostering technological innovations and precision farming solutions, in future this research aims to increase agricultural yields, particularly by enabling the cultivation of certain crops in locations different from their original ones.

Stevia Rebaudiana Bertoni Morita II, a perennial plant native to Paraguay and Brazil, is also widely cultivated in the state of Colima, Mexico, for its use as a sweetener in food and beverages. The op-timization of soil parameters is crucial for maximizing biomass production and stevioside levels in stevia crops. This research presents the development and implementation of a monitoring system to track essential soil parameters, including pH, temperature, humidity, electrical conductivity, ni-trogen, phosphorus, and potassium. The system employs a wireless sensor network to collect qua-si-real-time data, which is transmitted and stored in a web-based platform. A Mamdani-type fuzzy logic model is utilized to process the collected data and provide to farmers an integrated assessment of soil quality. By comparing the quality data output of the fuzzy logic model with a line-ar-regression model, the system demonstrated acceptable performance, with a determination coef-ficient of 0.532 for random data and 0.906 for gathered measurements. The system enables farmers to gain insights into the soil quality of their stevia crops and empowers them to take preventive and corrective actions to improve the soil quality specifically for stevia crops.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

Graft injury affects over 50% of liver transplant (LT) recipients, but non-invasive biomarkers to diagnose and guide treatment are currently limited. We aimed to develop a biomarker of graft injury by integrating serum metabolomic profiles with clinical variables. Serum from 55 LT recipients with biopsy confirmed metabolic-dysfunction associated steatohepatitis (MASH), T-cell mediated rejection (TCMR) and biliary complications was collected and processed using a combination of LC-MS/MS assay. The metabolomic profiles were integrated with clinical information using a multi-class Machine Learning (ML) classifier. The efficacy of the model was assessed through the evaluation of the Out-of-Bag (OOB) error estimate. Our ML model yielded an overall accuracy of 79.66% with an OOB estimate of the error rate at 19.75%. The model exhibited a maximum ability to distinguish MASH, with an OOB error estimate of 7.4% compared to 22.2% for biliary and 29.6% for TCMR. The metabolites serine and serotonin emerged as the topmost predictors. When predicting binary outcomes using 3 models: Biliary (biliary vs. rest), MASH (MASH vs. rest) and TCMR (TCMR vs. rest), the AUCs were 0.882, 0.972 and 0.96 respectively. Our ML tool integrating serum metabolites with clinical variables shows promise as a non-invasive, multi-class serum biomarker of graft pathology.

This paper proposes a hybrid medium access control (MAC) protocol for wireless sensor network (WSN) data gathering, employing unmanned aerial vehicles (UAV). The UAV sends a beacon frame periodically to inform sensor nodes regarding its presence. Afterward, each sensor node which receives beacon frame contends to send registration frame to the UAV. The UAV will transmit the second beacon frame to the registered nodes to notify their transmission schedule. The time-slot scheme is used for the transmission schedule. The transmission schedule of each sensor is determined based on their priority. Specifically, the priority of each sensor is determined during the registration process. Furthermore, the architecture of UAV-WSN data gathering system is introduced in this paper. Simulations are performed, showing that the proposed MAC protocol achieves fairness while enhancing network performance.

Compressive sensing originates in the field of signal processing and has recently become a topic of energy-efficient data gathering in wireless sensor networks. In this paper, we propose an energy efficient distributed compressive sensing solution for sensor networks. Proposed solution utilizes sparsity distribution of signals to group sensor nodes into several coalitions and then implements localized compressive sensing inside coalitions. This solution improves data-gathering performance in terms of both data accuracy and energy consumption. The approach curbs both data-transmission costs and number of measurements. Coalition-based data gathering cuts transmission cost, and the number of measurements is reduced by scheduling sensor nodes and adjusting their sampling frequency. Our simulation showed that our approach enhances network performance by minimizing energy cost and improving data accuracy.

IoTs and WSNs utilize their connectivity to enable solutions supporting a spectrum of industries in different and volatile environments. To effectively enhance the security and quality of service of networks, empirical research should take into account a variety of factors and be structured in a replicable manner. This will not only ensure scalability but also enable verification of conclusions, leading to more constructive outcomes. Cooja offers limited performance analysis capabilities of simulations, which are often extracted and calculated manually. In this paper, we introduce a framework and a toolkit that enable researchers to conduct structured and conclusive experiments considering different factors and metrics, experiment design to results analysis. Besides, this tool summarizes multiple network metrics and allows multiple scenarios. As proof of concept, this paper studies the flooding attacks on IoT and illustrates their impact on the network, leveraging the proposed framework and tools.

Load balancing, energy efficiency and fault tolerance are among the most important data dissemination issues in Wireless Sensor Networks (WSNs). In order to successfully cope with the mentioned issues, two main approaches (namely, Data-centric Storage and Distributed Data Storage) have been proposed in the literature. Both approaches suffer from data loss due to memory and/or energy depletion in the storage nodes. Even though several techniques have been proposed so far to overcome the mentioned problems, the proposed solutions typically focus on one issue at a time. In this paper, we integrate the Data-centric Storage (DCS) features into Distributed Data Storage (DDS) mechanisms and present a novel approach, denoted as Collaborative Memory and Energy Management (CoMEM), to overcome both problems and bring memory and energy efficiency to the data loss mechanism of WSNs. We also propose analytical and simulation frameworks for performance evaluation. Our results show that the proposed method outperforms existing approaches in various WSN scenarios.

Wireless Sensor Networks (WSNs) are being increasingly adopted in critical applications, where verifying the correct operation of sensor nodes is a major concern. Undesired events may undermine the mission of the WSNs. Hence their effects need to be properly assessed before deployment to obtain a good level of expected performance and during the operation in order to avoid dangerous unexpected results. In this paper we propose a methodology to support design and deployment of dependable WSNs by means of an event-based formal verification technique. The methodology includes a process to guide designers towards the realization of a dependable WSN and a tool ("ADVISES") to simplify its adoption. The tool allows to generate automatically formal specifications used to check correctness properties and evaluate dependability metrics at design time and at runtime. During the runtime we can check the behavior of theWSN accordingly to the results obtained at design time and we can detect sudden and unexpected failures, in order to trigger recovery procedures. The effectiveness of the methodology is shown in the context of two case studies, aiming to illustrate how the tool is helpful to drive design choices and to check the correctness properties of theWSN at runtime

in our increasingly interconnected world, sensor networks are critical in gathering and sending data for various applications, from environmental monitoring and industrial automation to healthcare and smart cities. However, as sensor networks expand in importance, so does the need to solve the multidimensional concerns of security, privacy, and forensics. This article explores the complex world of sensor network security, the delicate balance between data privacy and utility, and the emerging area of sensor network forensics. This article focuses on risk assessment of a network.

The application of artificial intelligence to point-of-care testing (POCT) disease detection has become a hot research field, in which breath detection which detects the patient's exhaled VOCs combined with sensor arrays of Convolutional Neural Network (CNN) algorithms as a new lung cancer detection is attracting more researchers' attention. However, due to low accuracy, high complexity computation and large number of parameters make the CNN algorithms difficult transplant to the embedded system of POCT devices. A lightweight neural network (LTNet) in this work is proposed to deal with this problem, and meanwhile, achieve high-precision classification of acetone and ethanol gases, which are respiratory markers for lung cancer patients. Compared to currently popular lightweight CNN models such as EfficientNet, LTNet has fewer parameters (32K) and its training weight size is only 0.155 MB. LTNet achieved an overall classification accuracy of 99.06% and 99.14% in the own mixed gas dataset and the University of California (UCI) dataset, which are both higher than that of the five existing models’, and it also offers the shortest training (844.38s and 584.67s) and inference time (23s and 14s) in the same validation set. Compared to the existing CNN models, LTNet is more suitable for resource-limited POCT devices.

Background. Gene rearrangements affecting KMT2A are frequent in acute myeloid leukemia (AML) and are often associated with a poor prognosis. KMT2A gene fusions are often detected by chromosome banding analysis and confirmed by fluorescence in-situ hybridization. However, small intragenic insertions, termed KMT2A partial tandem duplication (PTD), are particularly challenging to detect using standard molecular and cytogenetic approaches. Methods. We have validated the use of a custom hybrid capture based next-generation sequencing (NGS) panel for comprehensive profiling of AML patients seen at our institution. This NGS panel targets the entire consensus coding DNA sequence of KMT2A; to deduce the presence of a PTD we used the relative ratio of KMT2A exons coverage. We sought to corroborate the KMT2A-PTD NGS results using (1) multiplex-ligation probe amplification (MLPA) and (2) optical genome mapping (OGM). Results. We analyzed 932 AML cases and identified 41 individuals harboring a KMT2A-PTD. MLPA, NGS and OGM confirmed the presence of a KMT2A-PTD in 22 of the cases analyzed where orthogonal testing was possible. Two false positive PTD calls by NGS could be explained by the presence of cryptic structural variants impacting KMT2A and interfering with PTD analysis. OGM revealed the nature of these previously undetected gene rearrangements in KMT2A, while MLPA yielded in-conclusive results. MLPA analysis for KMT2A-PTD is limited to exon 4, whereas NGS and OGM resolved KMT2A-PTD sizes and copy number levels. Conclusion. KMT2A-PTDs are complex gene rearrangements that cannot be fully ascertained using a single genomic platform. MLPA, NGS panels and OGM are complementary technologies applied in standard of care testing for AML patients. MLPA and NGS panels are designed for targeted copy number analysis; however, our results show that integration of concurrent genomic alterations is needed for accurate KMT2A-PTD identification. Unbalanced chromosomal rearrangements overlapping with KMT2A can interfere with the diagnostic sensitivity and specificity of copy number based KMT2A-PTD detection methodologies.

Parasomnias are a group of sleep disorders characterized by abnormal and unpleasant motor, verbal or behavioral events that occur during sleep or during transitions between wake and sleep states. They disrupt sleep and can have a detrimental impact on the individual experiencing them. Our goal was to identify types of parasomnias and their prevalence in the post-secondary student population and to explore students' coping strategies for parasomnias they found distressing. Seventy-seven post-secondary students completed the 21-item Munich Parasomnia Screening (MUPS) frequency scale. They also rated, on a 10-point scale, how disturbing each parasomnia was. Not only did 92% percent of students report at least one parasomnia, but our results also indicate that the vast majority of students experienced more than one parasomnia. This led us to investigate the likelihood of the co-occurrence of different parasomnias. With respect to the level of subjectively experienced distress, the most prevalent parasomnias were not always the more disturbing ones. Coded open-ended responses about what students do about the disturbing parasomnias indicate that grounding strategies and physical manipulation of one’s body were the most common, although most participants indicated that in spite of distress, they do nothing to cope. In conclusion, our study found a strikingly high prevalence of parasomnias in this sample of young adults and a lack of knowledge about effective means of dealing with these.

The reliability of Underwater Wireless Sensor Networks (UWSNs) is measured in terms of energy consumption (EC), end-to-end delay(E2E) and packet delivery ratio (PDR). The adverse effects of channel may cause data loss. Reducing delay up to possible extend improves the reliability of the network, also increasing the number of nodes in a particular network increase reliability. Besides, increasing the number of nodes improve reliability but also increase power consumption. In order to overcome these shortcomings, the two routing protocols are proposed in this paper, namely Delay and Reliability Aware Routing (DRAR) protocol and Cooperative Delay and Reliability Aware Routing (Co-DRAR) protocol for UWSNs. In DRAR protocol, network is divided into two equal regions where two sink nodes(SNs) are positioned at upper region of the network and two SNs are placed at the mid region of the network. The protocol choose the relay node based on residual energy (RE), distance and Bit Error Rate (BER). These parameters protect the data packets from corruption and also provide stable path (where nodes remain active for longer period and do not die quickly). The protocol uses single link and may get worse sometimes while changing channel circumstances. To address this problem, cooperative routing scheme is added to DRAR protocol in order to developed its enhanced version known as Co-DRAR protocol. The protocol works by allowing the destination to receive multiple copies of data packets in order to decide the quality of packets. The proposed protocols DRAR and Co-DRAR perform routing irrespective to geographical position of sensors nodes conversely to the some of conventional routing protocols that's way our propose protocol better perform than the well-known protocol i.e. Depth base routing (DBR) in terms of EC, E2E, PDR, dead nodes, packet drop ratio and number of alive nodes (ANs).

The timely diagnosis of defects at their incipient stage of formation is crucial to extend the life-cycle of technical appliances. This is the case of mechanical-related stress, either due to long aging degradation processes (e.g., corrosion) or in-operation forces (e.g., impact events), which might provoke detrimental damages, such as cracks, disbonding or delaminations, most commonly followed by the release of acoustic energy. The localization of these sources can be successfully fulfilled via adoption of Acoustic Emission (AE)-based inspection techniques through the computation of the Time of Arrival (ToA), namely the time at which the induced mechanical wave released at the occurrence of the acoustic event arrives to the acquisition unit. However, the accurate estimation of the ToA may be hampered by poor Signal-to-Noise ratios (SNRs). In these conditions, standard statistical methods typically fail. In this work, two alternative Deep Learning methods are proposed for ToA retrieval, namely a Dilated Convolutional Neural Network (DilCNN) and a Capsule Neural Network for ToA (CapsToA). These methods have the additional benefit of being portable on resource-constrained microprocessors. Their performance has been extensively studied on both synthetic and experimental data, focusing on the problem of ToA identification for the case of a metallic plate. Results show that the two novel methods can achieve localization errors which are up to 70% more precise than those yielded by conventional strategies, even when the SNR is severely compromised (i.e., down to 2 dB). Moreover, DilCNN and CapsNet have been implemented in a tiny machine learning environment and then deployed on microcontroller units, showing a negligible loss of performance with respect to offline realizations.

Proteomics research has become one of the most important topics in the fields of life science and natural science. At present, research on protein–protein interaction networks (PPINs) mainly focuses on detecting protein complexes or function modules. However, existing approaches are either ineffective or incomplete. In this paper, we investigate function module detection mechanisms in PPIN, including open databases, existing detection algorithms and recent solutions. After that, we describe the proposed solution based on simplified swarm optimization (SSO) algorithm and gene ontology knowledge. The proposed solution implements SSO algorithm for clustering proteins with similar function, and imports biological gene ontology knowledge for further identifying function complexes and improving detection accuracy. Furthermore, we use four different categories of species dataset for experiment: Fruitfly, Mouse, Scere, and Human. The testing and analysis result show that the proposed solution is feasible, efficient and could achieve a higher accuracy of prediction than existing approaches.

Wireless sensor networks (WSN) are widely used in various fields such as military, industrial and transportation for real-time monitoring, sensing and data collection of different environments or objects. However, the development of WSN is hindered by several limitations, including energy, storage space, computing power and data transmission rate. Among these, the availability of power energy plays a crucial role as it directly determines the lifespan of WSN. To extend the life cycle of WSN, two key approaches are power supply improvement and energy conservation. Therefor, we proposed an energy harvesting system and a low energy consumption mechanism for WSN. Firstly, we delved into the energy harvesting technology of WSN, explored the utilization of solar energy and mechanical vibration energy to ensure a continuous and dependable power supply to the sensor nodes, and analyzed the voltage output characteristics of bistable piezoelectric cantilever. Secondly, we proposed a neighbor discovery mechanism that utilizes a separation beacon, is based on reply to ACK, and can facilitate the identification of neighboring nodes. This mechanism operates at a certain duty cycle ratio, significantly reduces idle listening time and results in substantial energy savings. In comparison to the Disco and U-connect protocols, our proposed mechanism achieves a remarkable reduction of 66.67% and 75% in the worst discovery delay, respectively. Furthermore, we introduced a data fusion mechanism based on integer wavelet transform. This mechanism effectively eliminates data redundancy caused by spatio-temporal correlation, results in a data compression rate of 5.42. Additionally, it significantly reduces energy consumption associated with data transmission by the nodes.

The sensor nodes have limited computation, sensing, communication capabilities and generally operated by batteries in a harsh atmosphere with non-replenish able power sources. These limitations force the sensor network subject to failure because most of the energy is spent on sensing, computing and data transmission. This paper introduces an Energy Efficient Clustering and Shortest-Path Routing Protocol (EECSRP) to assist Wireless Sensor Networks (WSNs) by (a) extending the lifespan of the network (b) effectively using the battery power (c) decreasing the network overhead and (d) ensuring a high packet transmission ratio with minimal delay. The delay time-based Cluster Head (CH) is elected based on the node degree, residual energy and Received Signal Strength (RSS) to accomplish the goal. Additionally, the RSS-based network partitioning is implemented to evaluate the gradient based on demand routing between source (sensing node) and destination (BS). Whenever the current CH residual energy goes under the threshold level, the proposed protocol performs the clustering process, reducing the exchange of control packets. However, the BS periodically gathers the data from every single CH which helps to reduce the collision and Medium Access Control (MAC) layer conflict. From the simulation results, it is the evident that the proposed protocol performance in terms of average end-to-end latency, packet delivery ratio, average energy consumption and control overhead is better than the well-known current protocols.

Healthcare professionals constantly face situations that reflect ecosystems’ degradation. These can negatively affect their mental health. Research suggests that hope and resilience can play an important role in this scenario, since they are related to/predict mental health in highly heterogeneous samples (considering geography, age, profession, health, etc.). In this context, the aims of the present study are: to characterize and explore the relationship between hope, resilient coping and mental health of Portuguese healthcare professionals. Using Google Forms, 276 healthcare professionals answered to the GHQ-28, the (adult) Trait Hope Scale, and the Brief Resilient Coping Scale (cross-sectional study). The minimum and maximum possible scores were reached, with the exception of the maximum score of GHQ-28-Total. Regarding Hope, 19.6% scored below the midpoint (M=43.46, SD=11.97); 29.3% revealed low resilience (M=14.93, SD=4.05); and the average of 4 of the 5 Mental Health scores (exception: Severe Depression) indicates the probability of a psychiatric case. Hope correlated with Social Dysfunction and GHQ-28-Total; resilient coping proved to be a (weak) predictor of 4 of the 5 GHQ-28 indicators (exception: Severe depression). The results support the need to promote the sample's mental health, hope and resilient coping. They also suggest that stimulating resilient coping may contribute to improving healthcare professionals’ mental health.

Wireless sensor networks are usually applied in hostile areas where nodes are easy to be moni-tored and captured by adversary. Key distribution is an essential primitive to provide most of security mechanism. However, the characteristic of limited resources of sensors restricts the direct use of conventional key distribution schemes. In this paper, a complete security key distribution scheme based on asymmetric cryptography technology is proposed in both static and mobile scenarios. Mutual authentication is guaranteed using challenge-response mechanism. The per-formance evaluation and security analysis show that the proposed scheme with low complexity not only provides better security for wireless sensor networks, but also reduces storage overhead and key exposure risks.

This work presents an LC resonant passive wireless gas sensor with a novel structure designed to mitigate the negative impact of substrate. The LC sensor antenna with the new structure and the reader antenna were designed and optimized utilizing HFSS software to improve the transfer efficiency. The superiority of the designed structure compared with the general ones is highlighted and verified. The change in the substrate capacitance has essentially no interference with the parameters to be measured of the LC sensor. The sensor with the new structure was prepared by combining etching and sputtering methods. The structure of the ZnO nanowires (NWs) was characterized to confirm their high purity and wurtzite crystal structure. The LC gas sensors demonstrated excellent wireless sensing performance including a low detection limit of 0.5 ppm NO2, high response of 1.058 and outstanding stability at 180 °C. The developed new sensor structure not only prevented interference from the substrate during gas sensing testing, but also expanded the choice of sensor substrates, playing a critical role in the development of sensors based on LC resonance principle.

Wireless sensor networks (WSNs) are a critical research area with numerous practical applications. WSNs are utilized in real-life scenarios, including environmental monitoring, healthcare, industrial automation, smart homes, and agriculture. As WSNs advance and become more sophisticated, they offer limitless opportunities for innovative solutions in various fields. However, due to their unattended nature, it is essential to develop strategies to improve their performance without draining the battery power of the sensor nodes, which is their most valuable resource. This paper proposes a novel sink mobility model based on constructing a bipartite graph from a deployed wireless sensor network. Using the bipartite graph’s properties, the mobile sink node can visit stationary sensor nodes in an optimal way to collect data and transmit it to the base station. We evaluated the proposed approach through simulations using the NS-2 simulator to investigate the performance of wireless sensor networks when adopting this mobility model. Our results show that using the proposed approach can significantly enhance the performance of wireless sensor networks while conserving the energy of the sensor nodes.

A run-of-the-mill remote sensor arrange comprises numerous vitality compelled sensor hubs that are arbitrarily sent is the sensor field. Vitality is one of the most significant parts of planning an information dispersal convention for applications, for example, war zone checking, living space observing, and so on. We present EGDD, an Energy-effective Grid-based Data Dissemination plot for arbitrarily conveyed remote sensor systems. The proposed conspire is vitality effective for dealing with both sink and source portability. EGDD depends on a virtual framework-based foundation for information scattering from various versatile sources to different portable sinks. The virtual lattice of square size is built by the main source showing up in the sensor field dependent on the remaining vitality of the sensor hubs. Moreover, we proposed an askew sending calculation for inquiry and information sending which guarantees that just a single spread hub advances the question and information at once. In EGDD, substitute scattering hubs are chosen ahead of time during the lattice development procedure and the least limit vitality level is characterized for spread hubs. When the vitality of a dispersal hub arrives at the base edge esteem, it is supplanted by another spread hub. The reenactment results show that the proposed EGDD conspire is more vitality proficient when contrasted with other information scattering conventions.

Wireless Sensor Networks (WSN) are the core of Internet of Things and require cryptographic protection due to the increase number of attacks. Cryptographic methods for WSN should be fast and consume low power as these networks consist of battery-powered devices and constrained microcontrollers. NTRU, the fastest and secure public key cryptosystem, uses high degree polynomials, and is susceptible to the lattice basis reduction attack (LBRA). CPKC, proposed by NTRU authors, works on integers modulo $q$ and is easily attackable by LBRA since it uses small numbers for the sake of the correct decryption. Herein, RCPKC, a random congruential public key cryptosystem working on integers modulo $q$ is proposed, such that the norm of a two-dimensional vector formed by its private key is greater than $\sqrt{q}$. RCPKC works similar to NTRU, and it is a secure version of insecure CPKC. RCPKC specifies a range from which the random numbers shall be selected, and it provides correct decryption for valid users and incorrect decryption for an attacker using LBRA by Gaussian lattice reduction. Because of its resistance to LBRA, RCPKC is more secure. Simultaneously, due to the use of big numbers instead of high degree polynomials, RCPKC is about 24 (7) times faster in encryption (decryption) than NTRU. Also, RCPKC is more three times faster than the most effective known NTRU variant, BQTRU. Compared to NTRU, RCPKC reduces energy consumption at least seven times that allows increasing life-time of unattended WSN more than seven times.

Deployment of unmanned aerial vehicles (UAVs) as aerial base stations (ABSs) has been considered to be a feasible solution to provide network coverage in scenarios where the conventional terrestrial network is overloaded or inaccessible due to an emergency situation. This article studies the problem of optimal placement of the UAVs as ABSs to enable network connectivity to the users in a coverage free zone. The main contributions of this work include two approaches to position the UAVs and to assign user equipment (UE) to each UAV, such that the sum-rate and the coverage probability of the network is maximized. An approach can be selected depending on the prevailing scenario. The first approach uses clustering algorithm to determine the 2D positioning of the UAV and a matching algorithm is used for UE assignment by considering the characteristics of the air-to-ground propagation channels as well as the impact of co-channel interference from ABSs. Then it uses exhaustive search on different altitudes to find the optimal altitude. In the second approach, 2D positioning and UE assignment are done similarly to the first approach. However, the sub-optimal altitude is estimated using particle swarm optimization (PSO). The first approach is suitable for a system which has computational resource constraints or lower probability of line of sight (LoS) links. In contrast, the second approach is suitable for data rate greedy systems or a higher probability of LoS links.

Wireless Sensor Networks (WSNs) has the characteristics of large-scale deployment, flexible networking, and wide application. It is an important part of the wireless communication networks. However, due to limited energy supply, the development of WSN is greatly restricted. Wireless Rechargeable Sensor Networks (WRSNs) transform the distributed energy around the environment into usable electricity through energy collection technology. In this work, a joint optimization strategy is proposed to improve the energy management efficiency for WRSNs. The joint optimization strategy is divided into two phases. In the first phase, we design an Annulus Virtual Force based Particle Swarm Optimization (AVFPSO) algorithm for area coverage planing. It adopts the multi-parameter joint optimization method to improve the efficiency of the algorithm. In the second phase, a Queuing Game-based Energy Supply (QGES) algorithm is designed for energy scheduling. It converts energy supply and consumption into network service. By solving the game equilibrium of the model, the optimal energy distribution strategy can be obtained. The simulation results show that our scheme improves the efficiency of coverage and energy, and extends the lifetime of WSN.

The interest in the Spark Plasma Sintering (SPS) technique has continuously increased over the last few years. This article shows the possibility of the development of a SPS device used for material processing and synthesis both in both scientific and industrial applications. This work presents an example of processing Arc-Meleted (half-Heusler, cobalt triantimonide) and SHS-synthesized semiconductors (bismuth telluride) materials with SPS device. The system functionalities expansion is presented, showing the possible way of increasing the information amount obtained about SPS processes and using the SPS apparatus for conducting synthesis of materials and increasing reproducibility and accuracy of process parameters control.

Programmable Object Interfaces are increasingly intriguing researchers because of their broader applications, especially in the medical field. In Wireless Body Area Network (WBAN), for example, the patients’ health can be monitored using clinical nano sensors. Exchanging such sensitive data requires a high level of security and protection against attacks. To that end, the literature is rich with security schemes that include the advanced encryption standard, secure hashing algorithm, and digital signatures that aim to secure the data exchange. However, such schemes elevate the time complexity rendering the data transmission slower. Cognitive Radio technology with a medical body area network system involves communication links between WBAN gateways, server and nano sensors rendering the entire system vulnerable to security attacks. In this paper, a novel DNA-based encryption technique is proposed to secure medical data sharing between sensing devices and central repositories. It has less computational time throughout authentication, encryption, and decryption. Our analysis of experimental attack scenarios shows that our technique is better than its counterparts.

Wireless sensor networks can provide a cheap and flexible infrastructure to support the measurement of noise pollution. However, the processing of the gathered data is challenging to implement on resource-constrained nodes, because each node has its own limited power supply, low-performance and low-power micro-controller unit and other limited processing resources, as well as limited amount of memory. We propose a sensor node for monitoring of indoor ambient noise. The sensor node is based on a hardware platform with limited computational resources and utilizes a number of simplifications to approximate more complex and costly signal processing stage. Furthermore, to reduce the communication between the sensor node and a sink node, as well as the power consumed by the IEEE 802.15.4 (ZigBee) transceiver, we perform digital A-weighting filtering and non-calibrated calculation of the sound pressure level on the node. According to experimental results, the proposed sound level meter can accurately measure the noise levels of up to 100~dB, with the mean difference of less than 2~dB compared to Class 1 sound level meter. The proposed device can continuously monitor indoor noise for several days. Despite the limitations of the used hardware platform, the presented node is a promising low-cost and low-power solution for indoor ambient noise monitoring.

The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of >1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.

Underwater communication for Underwater Wireless Sensor Networks (UWSNs) faces challenges due to the unique underwater environment. This review explores these challenges (attenuation, multipath propagation, limited bandwidth) across acoustic, optical, and radio frequency (RF) communication channels. It highlights how innovative antenna designs are crucial to mitigate these limitations and enable efficient data transmission. The review analyzes monopole, dipole, and helical antennas, discussing their trade-offs in radiation pattern, efficiency, and mitigating multipath effects. Advancements in materials, metamaterials, and reconfigurable antennas offer promising solutions for improved signal propagation, reduced attenuation, and better environmental adaptability. Research gaps include material exploration for low-conductivity antennas and optimizing antenna designs. Rigorous performance evaluation remains essential. Overall, advancements in underwater antenna technology are key to unlocking the full potential of UWSNs and enabling breakthroughs in marine applications.

This paper reports the novel design of a touch mode capacitive pressure sensor (TMCPS) system with a wireless approach for a full-range continuous monitoring of ventricular pressure. The system consists of two modules: an implantable set and an external reading device. The implantable set, restricted to a 2x2 cm² area, consists of a TMCPS array connected with a dual-layer coil, for making a reliable resonant circuit for communication with the external device. The capacitive array is modelled considering the small deflection regime for achieving a dynamic and full 5-300 mmHg pressure range. In this design, the two inductive-coupled modules are calculated considering proper electromagnetic alignment, based on two planar coils and considering the following: 13.56 MHz frequency to avoid tissue damage and three types of biological tissue as core (skin, fat and muscle). The system was validated with the Comsol Multiphysics and CoventorWare softwares; showing a 90% power transmission efficiency at a 3.5 cm distance between coils. The implantable module includes aluminum- and polyimide-based devices, which allows ergonomic, robust, reproducible, and technologically feasible integrated sensors. In addition, the module shows a simplified and low cost design approach based on PolyMEMS INAOE® technology, featured by low-temperature processing.

German noise action plans aim to reduce negative health outcomes from noise exposure and identify quiet areas free of noise pollution. Quiet area identification in German noise action plans is based primarily on noise mapping and spatial analysis and not empirical or qualitative data about acoustic environments, thus leaving a gap in the understanding of the quality of formally recognized quiet areas in noise action plans. This work presents a comparative empirical case study in Dortmund, Germany, with the aim to describe the diurnal dB(A) and biophonic properties of quiet areas versus noise 'hot spots'. Sound observations were collected (n=282,764) in five different natural or recreational land use patch types larger than four acres within 33 proposed quiet areas in Dortmund (n=70) and 23 noise hot spots between April 27^th, 2022 and March 2^nd, 2023. We find that quiet areas are on average more than 20 dB(A) quieter than noise hot spots almost every hour of the day. Forests, managed tree stands, cemeteries, and agriculture diel patterns are dominated by dawn dusk chorus in spring and summer, whereas sport and recreation as well as noise hot spots are dominated by traffic and human noise. A novel composite biophony mapping procedure is presented that finds distinct temporal distribution of biophony in forested and agriculture peri-urban locations positively associated with patch size, distance away from LDEN > 55, proximity to water, and the number of vegetation layers in the plant community. Anthrophony distribution dominates urban land uses in all hours of the day, but expands during day and evening and contracts at night and in dusk hours. The procedures presented here illustrate how qualitative information regarding quiet areas can be integrated into German noise action planning.

WBAN is a blessing to mankind because it can monitor people's health and activities regardless of place or time. It brings feasibility in patients’ treatment. The main problems with WBAN, however, are related to the security and privacy of health data. To prevent data misuse, health information should be safeguarded. On the other hand, the medical professional needs to receive the patient's health information promptly. As security of health data impact human life greatly so secure an efficient method is required. Efficient cryptographic technique for data protection of wireless body area network is proposed. This research aims to provide data protection in WBAN to increase data security and efficient transmission. The suggested approach offers effective security with quick key generation, quick encryption, and secure data transmission across the network. The proposed methodology is considered to be secure and will consume less time. The proposed method further uses a less complex encryption algorithm. The less complex the approach is the higher performance it will provide in wireless network. The proposed methodology will prevent many attacks, which makes the proposed approach highly suitable for wireless body area network’s security.

Abstract: Wireless body area networks (WBANs) have strong potential in the field of health monitoring. However, the energy consumption required for accurate monitoring limits the time between battery charges of the wearable sensors, which is a key performance factor (and can be critical in the case of implantable devices). In this paper, we study the inherent trade-off between the power consumption of the sensors and the probability of misclassifying a patient’s health state. We formulate this trade-off as a dynamic problem, in which at each step we can choose to activate a subset of sensors that provide noisy measurements of the patient’s health state. We assume that the (unknown) health state follows a Markov chain, so our problem is formulated as a partially observable Markov decision problem (POMDP). We show that all the past measurements can be summarized as a belief state on the true health state of the patient, which allows tackling the POMDP problem as an MDP on the belief state. We then empirically study the performance of a greedy one-step look-ahead policy compared to the optimal policy obtained by solving the dynamic program. For that purpose, we use an open-source Continuous Glucose Monitoring (CGM) data set of 232 patients over six months and extract the transition matrix and sensor accuracies from the data. We find that the greedy policy saves ~50% of the energy costs while reducing the misclassification costs by less than 2% compared to the most accurate policy possible that always activates all sensors. Our sensitivity analysis reveals that the greedy policy remains nearly optimal across different cost parameters and a varying number of sensors. The results also have practical importance, because while the optimal policy is too complicated, a greedy one-step look-ahead policy can be easily implemented in WBAN systems.

Background and Objectives: Knee osteoarthritis (KOA) is a degenerative disease that is targeting continuously people of different ages, but especially the elderly population, the number of which tends to increase continuously at the global level. Apart from age, excess weight can influence the evolution of the disease, with obesity being associated with a weak inflammation stage, and an imbalance between pro-inflammatory and anti-inflammatory cytokines. The present work aimed to identify specific biomarkers alike ACRP-30, IL-10, TNF-α, and IL-6 in synovial fluid and correlate them with patients’ clinical data. Materials and Methods: 24 subjects with KOA and over 50 years of age are involved in the present study. All patients performed a supine X-ray at the target knee. Ultrasound was performed using an ESAOTE MyLab Omega (ESAOTE Spa, Italy) ultrasound device and a 6-19 MHz linear array transducer. Results: The obtained results highlighted a significant correlation between age and adiponectin level (p=0.0451, r=-0.412). Also, the IL-10 values are lower in cases where the intensity of the pain is more pronounced (p=0.0405, r=-0.421). In addition, analyzing the data by gender, it was observed that in the case of males, stiffness is more related to age (p=0.0079, r=0.7993), compared to women (p=0.0203, r=0.6223). In the case of women, the progression of the disease tends to increase more intensively total WOMAC score’s values (p=0.00031, r=0.8342), compared with men (p=0.0289, r=7013). Regarding interleukins and BMI, significant correlations were observed only in the case of men. Conclusions: A significant correlation between age and adiponectin, and adiponectin and IL-6, suggests that advanced age may contribute to adiponectin reduction. Comparing men with women, it was observed that men's age is more related to rigidity, and IL-6 and IL-10 are directly correlated to BMI and women seem to be more sensitive to pain and stiffness.

A Wireless Body Area Sensor Network (WBASN) is combination of numerous sense nodes, positioned onto/close or inside a person body. Wireless Body Area Sensor Networks (WBASN) is a developing automation trend that exploits wireless sensor nodes to put instantaneous wearable well-being of ill person to improve individual’s existence. The sensor nodes might be used outwardly to observe abundant health parameters (like heart activity, blood pressure and cholesterol) of an ill person at a vital site within hospital. Hence the goal of WBASN is much crucial, enhancing the lifetime of nodes is compulsory to sustain many issues such as utility and efficiency. It is essential to evaluate time that when the first node will die it we want to refresh or change the battery reason is that loss of crucial information is not tolerable. The lifetime is termed as the time interval when a first node dies out due to battery exhaustion. In our proposed protocol life time of a network is the main concern as well other protocol related issues such as throughput, path loss, and residual energy. Bio-sensors are used for deployment on human body. Poisson distribution and equilibrium model techniques have been used for attaining the required results. Multi-hop network topology and random network node deployment used to achieve minimum energy consumption and longer network lifetime.

This work combines compressive sensing and short word-length techniques to achieve localization and target tracking in wireless sensor networks with energy-efficient communication between the network anchors and the fusion center. Gradient descent localization is performed using time-of-arrival (TOA) data which are indicative of the distance between anchors and the target thereby achieving range-based localization. The short word-length techniques considered are delta modulation and sigma-delta modulation. The energy efficiency is due to the reduction of the data volume transmitted from anchors to the fusion center by employing any of the two delta modulation variants with compressive sensing techniques. Delta modulation allows the transmission of one bit per TOA sample. The communication energy efficiency is increased by RⱮ, R≥1, where R is the sample reduction ratio of compressive sensing and Ɱ is the number of bits originally present in a TOA-sample word. It is found that the localization system involving sigma-delta modulation has a superior performance to that using delta-modulation or pure compressive sampling alone, in terms of both energy efficiency and localization error in the presence of TOA measurement noise, owing to the noise shaping property of sigma-delta modulation.

Wireless sensor networks are attractive largely because they need no wired infrastructure. But precisely this feature makes them energy constrained. Recent studies find that sensing behaviors that are otherwise deemed efficient consume comparable energy with communication. The duty cycle scheduling is perceived as contributing to achieving energy efficiency of sensing. Because of different research assumptions and objectives, various scheduling schemes have various emphases. This paper designed an adaptive sensing scheduling strategy. The objective function of the scheduling strategy includes minimizing average energy expenditure and maximizing sensing coverage (reducing event miss-rate), and it requires relatively loose assumptions. We determine the functional relationship between the variables of the objective function and the step-size parameters of the proposed strategy through the numerical fitting. We found that the objective function aggregated by the fitting functions is a bivariate multi-peak function that favors the Fibonacci tree optimization algorithm. Once the optimization of parameters is done, the strategy can be easily deployed and behaves consistently in the coming hours. We name the proposed strategy as “FTOS”. The experimental results show that the Fibonacci tree optimization algorithm gets a better optimistic effect than the comprehensive learning particle swarm optimization (CLPSO) algorithm and differential evolution (DE) algorithm. The FTOS strategy is superior to the fixed time scheduling strategy in achieving the scheduling objectives. It also outperforms other strategies with the same scheduling objectives such as LDAS, BS, DSS and PECAS.

Water quality monitoring was an important objective in the surroundings. In this study, we investigated the sensing characteristics of the arrayed flexible chloride sensor with XBee wireless sensing system. The sensitivity and linearity of the wireless chloride sensing devices were 91.6 mV/pCl and 0.988, respectively. The hysteresis voltages were 50.14 mV and 36.71 mV during the cycles of 1 M → 10⁻¹ M → 1 M → 10⁻³ M → 1 M and 1 M → 10⁻³ M → 1 M → 10⁻¹ M → 1 M, respectively. The selectivity coefficients of the ClO⁻ ion, ClO₄⁻ ion, NO₃⁻ ion and I⁻ ion for Cl⁻ ion were 5.0 × 10⁻², 1.0 × 10⁻¹, 5.9 × 10⁻³ and 5.6×10⁻¹, respectively. The sensing characteristics of real time measurement were investigated for dynamic microfluidic. The arrayed flexible chloride sensor was integrated with the microfluidic device, syringe pump and wireless sensing system. The sensitivity and linearity were 273.1 mV/pCl and 0.978 at 35 μL/min, respectively.

Underwater wireless sensor networks (UWSN) have recently been proposed as a way to monitor and explore the water depths' environments. Efficiently delivering the data is still a challenging problem in these networks because of the weaknesses in the acoustic transmission. To tackle such a problem, we propose a novel algorithm provides controlling mechanisms for critical long-term data forwarding underwater sensor networks, called Hop by Hop Power-Efficient Routing Protocol (Hⁿ-PERP). The proposed Hⁿ-PERP is a centralized full-control model that enhances the network's throughput and energy efficiency by a set of solutions depend on power monitoring in UWSN nodes. In particular, the model provides a guaranteed mechanism for scheduling and processing data transmission based on number of nodes, hops between the nodes, energy level and congestion within each node to minimize energy levels or power consumption by avoiding disconnected probability for any node, which in turn maximizing the network lifetime. Simulation results show that our proposed model is consistent with energy level and congestion, and is more accurate for enabling routing and data transmission. Therefore, the data packet delivery ratio and overall throughput also achieves robust scenarios of very sparse or/and weak networks, to keep on Performance stability in UWSN via adjusting hop-by-hop delay and energy consumption during packages delivery.

Wireless Sensor Networks are critical for modern applications ranging from environmental monitoring to smart city infrastructures. This research proposes a novel optimization learning and deployment strategy for Wireless Sensor Networks (WSNs) by 3D WUSN model is uniformly distributed M sensor nodes across diverse terrains, with clusters representing 20% of sensors, showcasing its ability to balance power consumption and extend network longevity, grounded in fuzzy clustering based protocol using the Fuzzy C-Means (FCM) method, called FCM-3DWUSN. Comparative analysis against established models including LEACH-C, K-Means and LEACH emphasized FCM-3DWUSN's outperformed performance, with average power consumption such as 134.990, 341.790, 143.895, and 192.984; respectively. The experimental result shows that FCM protocol in the 3D WUSN model can reduce energy consumption and improve the network lifetime to gather data and send the information.

The development of computational acoustics allows simulation of sound generation and propagation in complex environment. In particular, meshfree methods are widely used to solve acoustics problems through arbitrarily distributed field points and approximation smoothness flexibility. As a Lagrangian meshfree method, smoothed particle hydrodynamics (SPH) method reduce the difficulty in solving problems with deformable boundaries, complex topologies, or multiphase medium. The traditional SPH method has been applied in acoustic simulation. This study presents the corrective smoothed particle method (CSPM), which is a combination of SPH kernel estimate and Taylor series expansion. The CSPM is introduced as a Lagrangian approach to improve accuracy in solving acoustic wave equations in the time domain. Moreover, a boundary treatment technique based on the hybrid meshfree and finite difference time domain (FDTD) method is proposed to represent different acoustic boundaries with particles. To model sound propagation in pipes with different boundaries, soft, rigid, and absorbing boundary conditions are built with this technique. Numerical results show that the CSPM algorithm is consistent and demonstrates convergence with exact solutions. Main computational parameters are discussed, and different boundary conditions are validated to be effective for benchmark problems in computational acoustics.

Sensor networks, as a special subtype of wireless networks, consist of sets of wirelessly connected sensor nodes often placed in hard-to-reach environments. Therefore, it is expected that sensor nodes will not be powered from the power grid. Instead, sensor nodes have their own power sources, the replacement of which is often impractical and requires additional costs, so it is necessary to ensure minimum energy consumption. For that reason, the energy efficiency of wireless sensor networks used for monitoring environmental parameters is essential, especially in remote networking scenarios. In this paper, an overview of the latest research progress on wireless sensor networks based on LoRa was provided. Furthermore, the analyses of the energy consumption of sensor nodes used in agriculture to observe environmental parameters were carried out. Optimization methods of energy consumption, in terms of choosing the appropriate data collection processes, as well as the settings of wireless network radio parameters were suggested. In the conducted analyses, special emphasis was placed on choosing the optimal package size. In this paper, it was proven that the adjustment of the transmission speed to the actual size of the packet is important for better energy efficiency of communication.

Wireless Sensor Networks (WSNs) continue to provide essential services for various applications such as surveillance, data gathering, and data transmission from the hazardous environments to safer destinations. This has been enhanced by the energy-efficient routing protocols that are mostly designed for such purposes. Gateway-based Energy-Aware Multi-hop Routing protocol (MGEAR) is one of the homogenous routing schemes that was recently designed to more efficiently reduce the energy consumption of distant nodes. However, it has been found that the protocol has a high energy consumption rate, lower stability period, less data transmission to the Base station (BS). In this paper, an enhanced Heterogeneous Gateway-based Energy-Aware multi-hop routing protocol ( HMGEAR) is proposed. The proposed routing scheme is based on the introduction of heterogeneous nodes in the existing scheme, selection of the head based on the residual energy, introduction of multi-hop communication strategy in all the regions of the network, and implementation of energy hole elimination technique. Results show that the proposed routing scheme outperforms two existing ones.

The radio operation in wireless sensor networks (WSN) in the Internet of Things (IoT) applications are the most common source for power consumption. However, recognizing and controlling the factors affecting radio operation can be valuable for managing the node power consumption. ContikiMAC is a low-power Radio Duty-Cycle protocol in Contiki OS used in WakeUp mode, which is a clear channel assessment (CCA) to check radio status periodically. The time spent to check the radio is of utmost importance for monitoring power consumption. It can lead to false WakeUp or idle listening in Radio Duty-Cycles and ContikiMAC. This paper presents a detailed analysis of radio WakeUp time factors of ContikiMAC. Then, we propose lightweight CCA (LW-CCA) as an extension to ContikiMAC to reduce the percentage of Radio Duty-Cycles in false WakeUps and idle listenings by using dynamic received signal strength indicators (RSSI) status check time. The simulation results in the Cooja simulator show that LW-CCA reduces about 8% energy consumption in nodes while maintaining up to 99% of the packet delivery rate (PDR).

Wireless sensor networks are widely used in many applications such as environmental monitoring, health care, smart grid and surveillance. Many security protocols have been proposed and intensively studied due to the inherent nature of wireless networks. In particular, Wu et al. proposed a promising authentication scheme which is sufficiently robust against various attacks. However, according to our analysis, Wu et al.'s scheme has two serious security weaknesses against malicious outsiders. First, their scheme can lead to user impersonation attacks. Second, user anonymity is not preserved in their scheme. In this paper, we present these vulnerabilities of Wu et al.'s scheme in detail. We also propose a new scheme by fixing such vulnerabilities and improving the performance of the protocol.

The extensive deployment of wireless infrastructure provides a low-cost way to track mobile users in indoor environment. This paper demonstrates a prototype model of an accurate and reliable room location awareness system in a real public environment, where three typical problems arise. First, a massive number of access points (APs) can be sensed leading to a high-dimensional classification problem. Second, heterogeneous devices record different received signal strength (RSS) levels due to the variations in chip-set and antenna attenuation. Third, APs are not necessarily visible in every scanning cycle leading to missing data. This paper presents a probabilistic Wi-Fi fingerprinting method in a hidden Markov model (HMM) framework for mobile user tracking. Considering the spatial correlation of the signal strengths from multiple APs, a Multivariate Gaussian Mixture Model (MVGMM) is fitted to model the probability distribution of RSS measurements in each cell. Furthermore, the unseen property of invisible AP has been investigated in this research, and demonstrated the efficiency of differentiation between cells. The proposed system is able to achieve comparable localization performance. The filed test results present a reliable 97% localization room level accuracy of multiple mobile users in a real university campus WiFi network without any prior knowledge of the environment.

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

Unmanned delivery technology using unmanned aerial vehicles (UAVs) has the potential to solve issues such as traffic congestion and labor shortages. We investigated a method to construct a route between the source and destination nodes in a wireless multi-hop network by installing a radio terminal in each house. If the relay functions of all nodes in the network are in operation, the number of control messages for route construction increases, and the message relay forwarding load of each node increases. Keeping all node pairs multi-hop connectivity, we establish a method to operate the relay function with as few nodes as possible. End nodes that have not activated the relay function connect to the relay node with the closest physical distance. In this paper, we propose methods for selecting nodes to operate the relay function. Specifically, one method is based on random selection, another method is based on the number of adjacent nodes, and a third method is based on the Multipoint Relay (MPR) of the Optimized Link State Routing Protocol (OLSR). For each method, we evaluate whether the route construction is available, the number of relay nodes, the total distance of constructed routes, and the distance in population-dense regions. We clarify the characteristics of each method, and the method based on MPR is the best for constructing a network suitable for UAV navigation routes. In addition, the smaller the number of relay nodes, the more unexpected collisions on the links due to route conflicts. We clarify the minimum node density required to apply the MPR method which reduces the number of relay nodes suppressing route conflicts.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

In this article, we describe a simple procedure for evaluating the sterility of nutrient media using a shear-horizontal surface acoustic wave (SH-SAW) biosensor. We used the SH-SAW biosensor platform to monitor the time-dependent phase responses of the material for the media that binds to a monolayer of 3-mercaptopropanyl-N-hydroxy succinimide on the biosensor surface. Increases in the phase shift less than 50% of the starting phase shift recorded 180 minutes after the sterilization indicate a successful sterility test of the media. Our devices were then applied to sterility testing using a viable Escherichia coli (E. coli) K-12 solution to confirm our hypothesis. Filtered LB Broth was the negative control, and a 24-hour culture of E. coli was the positive control. Before testing, the cell solution was pelleted, the media decanted, and then replaced with a 1x phosphate-buffered saline solution (1x PBS). Since we know that the N-hydroxysuccinimide residues will bind to amine groups, only in cases where microbial species are present will the surface binding increase greater than 50%. We confirmed our hypothesis using SH-SAW biosensors and overnight E. coli cultures. The sensitivity for our 250 MHz quartz SH-SAW sensors was calculated based on the response from the E. coli K-12 solution over the linear dynamic range, which appears to be 2x10^4 – 2x10^7 CFU per ml and has a sensitivity of S = 1.655x10^5 o m2 Kg-1. The limit of detection (LOD) for these sensors was calculated to be approximately 2x10^-9 grams (g), which is estimated to be approximately 2,000 Escherichia coli (E. coli) K-12 cells. However, the sensitivity and insertion loss remained approximately unchanged before and after coating the sensor with 3,3'-Dithiobis(succinimidyl) Propionate (DSP).

One of the major concerns in structural health management (SHM) is the early detection of a growing crack. Using this, future damage due to crack propagation can be mitigated or eliminated by implementing proper repair and maintenance. Acoustic Emission (AE) is a non-destructive testing (NDT) method with potential applications for locating and monitoring fatigue cracks. The research presented in this paper focuses on SHM using AE. A novel AE signal analysis approach was proposed in order to detect crack initiation and assess small crack lengths. Experimental investigation indicated that initiation of a crack could be identified through the statistical analysis of the resulting features of the AE signals. A probabilistic AE-based model for small fatigue crack sizing was developed and the uncertainties of the model were estimated. In addition, a probabilistic model validation approach was implemented to confirm accurate estimation of the results. The outcome of this research can be used to evaluate the integrity of structures under fatigue loading. The proposed approach can also be applied as an approach to manage health and assess prognosis of structures.

Abstract: With the growing integration of the Internet of Things (IoT) in smart buildings, it is crucial to ensure the precise implementation and operation of wireless sensor networks (WSNs). This paper aims to study the implementation aspect of Wireless Sensor Networks (WSNs) in a commercial multi-story building, specifically addressing the difficulty of dealing with variable environmental conditions on each floor. This research addresses the disparity between simulated situations and actual deployments, offering valuable insights that have the potential to signifi-cantly improve the efficiency and responsiveness of building management systems. We obtain real-time sensor data to analyze and evaluate the system’s performance. Our investigation is grounded in the growing importance of incorporating WSNs into buildings to create intelligent environments. By leveraging the capabilities of Contiki operating system, this study employs a specialized simulator to generate simulated data, allowing for a comparison between real-world and simulated scenarios. We provide an in-depth analysis to scrutinize the disparities and commonalities between the datasets obtained from real-world deployments and simulated en-vironments. We highlight the necessity of precise simulation to validate real-life sensor data, shedding light on the challenges and opportunities associated with implementing WSNs in in-telligent buildings. Results obtained show the significance of accurate simulation models for re-liable data representation, providing a roadmap for further developments in the integration of WSNs into intelligent building scenarios. The findings highlight the potential for optimizing living and working conditions based on the real-time monitoring of critical environmental pa-rameters. This includes insights into temperature, humidity, and light intensity, offering oppor-tunities for enhanced comfort and efficiency in intelligent environments.

In wireless sensor networks, there is no a central controller to enforce cooperation between nodes. Therefore, nodes may generate selfish behavior to conserve their energy resources. In this paper, we address the problems of transmission power minimization and energy balance in wireless sensor networks using a topology control algorithm. We considered the energy efficiency and energy balance of the nodes, and an improved optimization-integrated utility function is designed by introducing the Theil index. Based on this, a topological control game model of energy balance is established, and it is proved that the topological game model is an ordinal potential game with Pareto optimality. Additionally, an energy-balanced topology control game algorithm (EBTG) is proposed to construct topologies. The simulation and comparison show that, compared with other topological control algorithms based on game theory, the EBTG algorithm can improve energy balance and energy efficiency while reducing the transmitting power of nodes, thus prolonging the network lifetime.

A portable laser photoacoustic sensor based on a Field-Programmable Gate Array (FPGA) is reported for methane detection. A tunable DFB diode laser in the 1654 nm wavelength range is used as an excitation source. The photoacoustic signal processing was implemented by a FPGA device. A small resonant photoacoustic cell is designed. The minimum detection limit (1σ) of 10 ppm for methane (CH₄) is demonstrated.

Following the adoption of the Kunming-Montreal Global Biodiversity Framework (KM-GBF), with the Convention on Biological Diversity serving as its guiding treaty, the European Union (EU) has just reached an agreement on an EU Nature Restoration Regulation. This study carries out a systematic cross-walk between the restoration regulation and the KM-GBF, focusing on their implications for forest ecosystems. This paper identifies areas of alignment, divergence, and potential gaps related to habitat restoration, species protection, climate resilience, and the sustainable use of natural resources. The methodology adopts a grounded approach, starting with the 23 targets outlined in the KM-GBF and proceeding to the 28 articles set out in the restoration regulation. The results highlight the need for better alignment between the KM-GBF, the restoration regulation, and other forest-relevant EU policy instruments. The study stresses the need for a coherent and integrated EU policy approach that can address the diverse challenges and policy objectives facing forests. It concludes that amendments to the restoration regulation have significantly diluted its potential impact, limiting the EU Members States accountability and ability to meet KM-GBF goals and targets. It further stresses the need for strategies that can reconcile divergent EU policy pathways, support forest management and restoration efforts, while aligning with global biodiversity objectives.

Complementary Metal-Oxide-Semiconductor (CMOS) is a typical image sensor that has a wide range of applications. However, considering the limitations of the weather condition and hardware cost, it is hard to capture high-resolution images by CMOS sensor. Recently, Super-Resolution (SR) techniques for image restoration has been gaining attentions due to its excellent performance. Under the powerful learning ability, Generative Adversarial Networks (GANs) have been proved to achieve great success. In this paper, we propose the Advanced Generative Adversarial Networks (AGAN) to efficiently correct these issues; 1) we design a Laplacian pyramid framework as pre-trained module, which is beneficial to provide multi-scale features for our input. 2) at each feature block, a convolutional skip-connections network, which may contain some latent information, is significant for generative model to reconstruct a plausible-looking image; 3) considering that edge details usually play an important role in image generation, a novel perceptual loss function is defined to train and seek optimal parameters. It is effective to achieve excellent and compelling quality captured by CMOS sensor. Quantitative and qualitative evaluations have been demonstrated that our algorithm not only fully takes advantage of Convolutional Neural Networks (CNNs) to improve the image quality, but also performs better than previous GAN algorithms for super-resolution task.

This study evaluates audiogenic epilepsy in Krushinsky-Molodkina rats using a wireless EEG system to overcome the limitations of traditional methods that restrict animal movement. Nine male KM rats, prone to audiogenic seizures, were implanted with electrodes in areas critical for seizure activity (inferior colliculus, ventrolateral periaqueductal gray, dorsal area of the secondary auditory cortex, and motor cortex). This setup allowed for the observation of seizures without movement restriction. Results showed that targeted neural intervention via electrode implantation reduced the intensity of convulsive seizures in half of the subjects, suggesting a potential therapeutic approach. The severity of seizures was influenced by the pre-phonostimulation EEG background activity in specific brain regions, identifying them as key in the genesis and generalization of seizures. Observations of dual generalized seizure waves and induced hyperkinesis challenge conventional epilepsy models and suggest new directions for research and therapy development.

The acoustic environment in learning spaces significantly influences learning effectiveness and occupant well-being. Recent studies have shown that a series of architectural factors within physical learning environments can impact students' educational experiences. This research delves into the relationship between architectural characteristics and the perceived acoustic environment among 467 primary students in 19 learning spaces across 9 schools in Chile. The survey comprises a student questionnaire, a checklist evaluating space characteristics, and acoustic measurements of indoor noise levels during occupied conditions. Examined topics include Indoor Environmental Quality (IEQ) comfort perception, noise annoyance, hearing ability, and acoustic preference. Architectural characteristics considered encompass flexible and acoustic space design parameters. The results indicated that noise discomfort was a common issue, especially in traditional learning spaces without acoustic treatment. The type of learning space (traditional or flexible settings) has a greater impact on acoustic perception particularly concerning noise discomfort and acoustic preference. However, poorly acoustic spaces lacking absorbing materials or exhibiting lower spatial density (m2 per student) contribute to increased indoor noise levels affecting noise annoyance caused by children's talking inside. The study emphasizes the importance of considering both architectural design and acoustic conditioning for optimizing the acoustic experience in educational spaces.

One of the challenges of deploying Wireless Sensor Networks (WSN) at large scale is to operate for prolonged periods of time relying on the limited amounts of energy stored in its nodes. Generally, data communication is the main factor of draining energy. Consequently, reducing the amount of transmitted data by the nodes is of great interest. At the same time, reducing data to be transmitted should not decrease the quality of the deduced information. Solving this problematic is what we call in this article "Ensuring the Quality of Information Service (QoIS)". This document provides a state-of-the-art for the QoIS regarding WSNs. At first, we give a quick overview of the Internet of Things (IoT) paradigm and the WSN technologies in order to understand how data is gathered and used in these networks. Also, we introduce a novel concept: QoIS, in contrast with classic QoS. Then, it is expected a summary of criteria that asses the QoIS in WSNs plus some techniques to improve it. In this article, we will focus on data management techniques. These techniques can improve raw data, information and/or knowledge quality in energy-constrained WSNs. Finally, we give some conclusions and a glimpse about our future work.

This project designed a set of network security mechanisms for cloud applications in VANETs. At present, cloud computing is one of the government’s development priorities in the industry. We divide cloud into public, private, and hybrid clouds in this project. Vehicles or passengers can access road conditions or public transport information through the public cloud; public transportation can access current driving records and users can access relevant enterprise information on the private cloud and hybrid cloud is a combination of public and private clouds. Both cloud computing or VANETs require network and information security. At present, many researches on VANETs security only focus on message communication, and neglect information storage. Researches on cloud computing security only focus on information protection, and neglect user privacy and anonymity. This project designed a set of network and information security mechanisms in line with the requirements of Confidentiality, Authentication, Non-repudiation, Conditional Anonymity, and Conditional Untraceability. This project primarily needs to achieve the following: 1.an authentication mechanism to verify the identity of each other between the passenger and the vehicle and to verify the identity with Single Sign-On; 2. vehicle or user privacy and anonymity, which need to be able to replace the anonymous ID and related parameters for the vehicle or the user; 3. a private communication mechanism, which enables any vehicle or user to communicate privately; and 4. an information security encryption method, which can encrypt the information on a cloud server to avoid unauthorized access by internal personnel or hackers.

The issues concerning the development of the smart systems for the management of freight transport are related to many factors which are influencing by properties of such a complex processes and ICT development. We are concerned with the recognition of a wide spectrum of services and provision specifics under conditions of wireless communication networks. Also, we are investigated for the adequate provision of context data with problematic of a definition of such context data and with possibilities to apply formalized artificial intelligence methods for recognition of this context information needs for transportation. In this stage of application of the smart system, we are solving the problem of priority of provision of possible providing services, ensuring of quite optimal quality of data supply channels and restriction of flooding of wireless communication channels. The proposed methodology is based on methods of indication of con-text-aware situations and integration of such data into the situation recognition algorithms. The constructions of smart service provision system are developed for more safety management of transportation. The experimental results are demonstrated on analysis of heterogeneity of smart services, construction of schemas for service provision priorities, and extension of potential of intelligent transport with intellectual recognition possibilities of context-aware information in the transportation process.

A single tree topology is a commonly employed topology for wireless sensor networks (WSN) to connect sensors to one or more remote gateways. However, its many-to-one traffic routing pattern imposes heavy burden on downstream nodes, as the same routes are repeatedly used for packet transfer, from one or more upstream branches. The challenge is how to choose the most optimal routing paths that minimizes energy consumption across the entire network. This paper proposes a proactive energy awareness-based many-to-one traffic routing scheme to alleviate the above said problem referred to as Energy Balance-Based Energy Hole Alleviation in tree topology (EBEHA-T). This protocol combines updated status of variations in energy consumption pattern around sink-hole zones and distribution of joint nodes among the trees. With this approach, EBEHA-T proactively prevents sink-hole formation instead of just a reactive response after they have occurred. Performance evaluation of EBEHA-T against benchmark method RaSMaLai shows increased energy saving across the entire network and a marked improvement in energy consumption balance in energy-hole zones. This precludes energy hole formation and the consequent network partitioning, leading to improved network lifetime beyond that of the RasMaLai. OMNET++ network simulation software has been used for the evaluation.

We present a surface acoustic wave (SAW) sensor array for microRNA (miRNA) detection that utilizes photocatalytic silver staining on titanium dioxide (TiO2) nanoparticles as a signal enhancement technique for high sensitivity with an internal reference sensor for high reproducibility. A sandwich hybridization was performed on working sensors of the SAW sensor array that could simultaneously capture and detect three miRNAs (miRNA-21, miRNA-106b, and miRNA-155) known to be upregulated in cancer. Sensor responses due to signal amplification varied depending on the concentration of synthetic miRNAs. It was confirmed that normalization (a ratio of working sensor response to reference sensor response) screened out background interferences by manipulating data and minimized non-uniformity in the photocatalytic silver staining step by suppressing disturbances to both working sensor signal and reference sensor signal. Finally, we were able to successfully detect target miRNAs in cancer cell-derived exosomal miRNAs with performance comparable to the detection of synthetic miRNAs.

The partial discharge (PD) event in high voltage insulation releases energy, exerts mechanical pressure, and generates elastic waves. Detecting and locating these PD events through short-duration acoustic pulses is well-established, particularly in gas-insulated systems and oil-insulated transformers. However, its full potential remains untapped in solid insulation systems, where the propagation capability of acoustic pulse and the acoustic reflections pose fundamental challenges to the Acoustic Emission (AE) detection technique. This study investigates the influence of reflections and multiple paths on the propagating acoustic pulse in polymeric insulating materials using a finite element method (FEM) in COMSOL. It was observed that the reflections from the boundary influence the propagating pulse's shape, peak magnitude, and arrival time. An analytical MATLAB model further quantifies the impact of multiple propagation paths on the shape, magnitude, and arrival time of the pulse travelling in a cylinder. Additionally, a Perfect Matched Layer (PML) was implemented in the COMSOL model to eliminate reflections from the boundary, and it revealed that the acoustic pulse magnitude decreases with distance following the inverse square law. In essence, the models aid in measuring how reflections contribute to the observed signals, facilitating the precise identification of the source of the PD event in the tested system.

Many engineered approaches have been proposed over the years for solving the hard problem of performing indoor localisation using smartphone sensors. However, specialising these solutions for difficult edge cases remains challenging. Here we propose an end-to-end hybrid multimodal deep neural network localisation system, MM-Loc, relying on zero hand-engineered features, learning them automatically from data instead. This is achieved by using modality-specific neural networks to extract preliminary features from each sensing modality, which are then combined by cross-modality neural structures. We show that our choice of modality-specific neural architectures is capable of estimating the location with good accuracy independently. But for better accuracy, a multimodal neural network fusing the features of early modality-specific representations is a better proposition. Our proposed MM-Loc solution is tested on cross-modality samples characterised by different sampling rates and data representation (inertial sensors, magnetic and WiFi signals), outperforming traditional approaches for location estimation. MM-Loc elegantly trains directly from data unlike conventional indoor positioning systems, which rely on human intuition.

In the famous medieval magical manual called Picatrix, the unknown author describes the phenomenon of magic with the term nigromantia. As is well known, the original meaning of the Greek term necromantia has a more concise meaning. It is used for a special kind of divination, i.e., divination through the parts of a cadaver and the conjured spirit of the dead. Seemingly in the Picatrix, no necromantic ritual can be found; moreover, the author stresses that his main goal is pious, i.e., to find the path leading to the ultimate source of the universe, the one and only God. In my paper, I show that on some pages of the Picatrix, there are traces of divinatory practices that may be connected to the original meaning of the term nigromantia. In the third book of the manual, descriptions of some interesting rituals attributed to the pagan Sabeans of Harran and their teacher, the god Hermes can be found. During the practices, the magician involved conjured spirits of the heavenly bodies and powers as well. Because of this, by looking closely at and analyzing the given text, it is possible to piece together a complex web of necromantic and demonic divinatory rituals.

Hepatitis C virus (HCV) is a major public health threat associated with serious clinical consequences worldwide. The WHO reports an estimated 58 million people globally living with chronic hepatitis C virus (HCV) infection, with 1.5 million new cases and over 350,000 deaths annually due to HCV-related diseases. Despite the existence of multiple diagnostic methods, the accessibility of diagnosis and treatment is often hindered across the continent by limited resources, insufficient healthcare infrastructure, and low public awareness of Hepatitis C virus Hepatitis C virus infection is a major public health concern in African countries, which have the highest prevalence rates of HCV in the world (1–26%). Egypt, African country which had the highest prevalence of Hepatitis C virus infection in the world. Its national hepatitis C elimination initiative emerges as an exemplary case of success an having screened over 60 million individuals, and treated more than 4 million, thereby markedly diminishing both the prevalence and incidence of the disease. The strategies employed by Egypt offer critical insights and adaptable frameworks for other African Countries facing analogous challenges. The Aim of this Review is to highlight the triumphs and hurdles of Egypt's approach, while also providing strategic guidance for African Countries to accelerate the journey towards the eradication of hepatitis C.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

A low-cost machine learning (ML) algorithm is proposed and discussed for spatial tracking of unknown, correlated signals in localized, ad-hoc wireless sensor networks. Each sensor is modeled as one neuron and a selected subset of these neurons are called to identify the spatial signal. The algorithm is implemented in two phases of spatial modeling and spatial tracking. The spatial signal is modeled using its M iso-contour lines at levels {ℓj}j=1M and those sensors that their sensor observations are in Δ margin of any of these levels report their sensor observations to the fusion center (FC) for spatial signal reconstruction. In spatial modeling phase, the number of these contour lines, their levels and a proper Δ are identified. In this phase, the algorithm may either use adaptive-weight stochastic gradient or scaled stochastic gradient method to select a proper Δ. Additive white Gaussian noise (AWGN) with zero mean is assumed along with the sensor observations. To reduce the observation noise’s effect, each sensor applies moving average filter on its observation to drastically reduce the effect of noise. The modeling performance, the cost and the convergence of the algorithm are discussed based on extensive computer simulations and reasoning. The algorithm is proposed for environmental monitoring. In this paper, the percentage of the communication attempts of wireless sensors is assumed as cost. Performance evaluation results show that the proposed spatial tracking approach is low cost and can model the spatial signal over time with the same performance as that of spatial modeling.

In this project, four of fibers Bragg gratings were fabricated by injecting different volumes of liquids (star line Glass Mechanix optical adhesive material, olive oil diluted with ethanol) into the hollow core fiber. The amplitude splitting interferometric technique with a high resolution specially designed translation stage was used for the fabrication process. The fabrication was done using ultraviolet laser operated at wavelength 405nm. The fabricated Bragg length of the four fibers is equal to 3.8 cm. The results presented fiber Bragg grating (FBG) with successful fabrication at 653.3 nm Bragg reflected wavelength.

To facilitate wireless communication, ocean exploration, and various environmental and research applications, the underwater Internet of Things has been developed with an infrastructure of acoustic sensor networks. There has been a significant increase in failures and a decrease in the efficiency of the network due to the fluid and challenging underwater environment. Consequently, achieving quality of service (QoS) in underwater networks remains a research area. Supporting QoS in underwater sensor networks is challenging due to resource limitations such as processing power, memory, bandwidth, and power sources. The purpose of this study was to examine the service quality requirements as well as protocols that have been implemented in recent years. Finally, based on quality criteria, we have presented a routing solution based on fuzzy logic, which is more efficient than other recent methods regarding energy consumption rate, JFI, efficiency, and reliability.

Human exposure to infectious aerosols results a transmission of diseases, such as influenza, tuberculosis, and COVID-19. Most dental procedures generate a significant number of aerosolized particles, increasing transmission risk in dental settings. Since the generation of aerosols in dentistry is unavoidable, many clinics started using intervention strategies such as area-filtration units and extraoral evacuation equipment, especially under the relatively recent constraints of the pandemics. However, the effectiveness of these devices in dental operatories has not been studied. Therefore, the dental personnel's ability to position and operate such instruments efficiently is also limited. To address these challenges, we utilized a real-time sensor network for assessment of aerosol dynamics during dental restoration and cleaning producers with and without intervention. The strategies tested during the procedures were (i) local area high-efficiency particle air (HEPA) filters and (ii) extra-oral suction device (EOSD). The study was conducted at the University of Washington School of Dentistry using a network of thirteen fixed sensors positioned within the operatory and one wearable sensor worn by the dental operator. The sensor network provides time and space-resolved particulate matter (PM) data. Three-dimensional (3D) visualization informs aerosol persistence in the operatory. It was found that area filters did not improve the overall aerosol concentration in dental offices significantly. An average of 16% decrease in PM concentration was observed when EOSD equipment was used during the procedures. The combination of real-time sensors and 3D visualization can provide dental personnel and facility mangers with actionable feedback to effectively assess aerosol transmission in medical settings and develop evidence-based intervention strategies.

Road networks are monitored to evaluate their decay level and the performances regarding ride comfort, vehicle rolling noise, fuel consumption, etc. In this study, an Inertial Measurement Unit is proposed by using a low-cost three-axis Micro-Electro-Mechanical Systems accelerometer and a GPS instrument, which are connected to a Raspberry Pi Zero W board and embedded inside a vehicle to monitor indirectly the road condition. To assess the level of pavement decay, the comfort index awz defined by the ISO 2631 standard was considered. Considering 21 km of roads, with different levels of pavement decay, validation measures made using the proposed IMU, another pre-assembled IMU, and a Road Surface Profiler were performed. Therefore, comparisons between awz determined with accelerations measured on the two different IMU are made; in addition, also correlations between awz, International Roughness Index (IRI), and Ride Number (RN) were performed. The results were shown very good correlations between the awz calculated with the proposed IMU and ones in the other IMU. In addition, the correlations between awz and IRI and RN were showed promising results, considering the use and the costs of the proposed IMU as a reliable method to assess the pavements decay in road networks where the use of traditional systems is difficult and/or not cheap.

World Health Organization (WHO) provides the guideline for managing the Particulate Matter (PM) level because when the PM level is higher, it threats the human health. For managing PM level, the procedure for measuring PM value is needed firstly. We use Tapered Element Oscillating Microbalance (TEOM)-based PM measuring sensors because it shows higher cost-effectiveness than Beta Attenuation Monitor (BAM)-based sensor. However, TEOM-based sensor has higher probability of malfunctioning than BAM-based sensor. In this paper, we call the overall malfunction as an anomaly, and we aim to detect anomalies for the maintenance of PM measuring sensors. We propose a novel architecture for solving the above aim that named as Hypothesis Pruning Generative Adversarial Network (HP-GAN). We experimentally compare the several anomaly detection architectures to certify ours performing better.

The radio activity in Wireless Sensor Networks (WSN) and Internet of Things (IoT) applications are the most common reason for power consumption. However, recognizing and controlling the factors affecting radio activity can be valuable for managing node power. ContikiMAC is a low-power Radio Duty-Cycle protocol in Contiki OS that uses Clear Channel Assessments (CCA) to check radio status periodically. The time taken to check the radio in receive mode WakeUp, is one of the most important reasons for power consumption which in most the cases can lead to negative WakeUp in Radio Duty-Cycles and ContikiMAC especially. Here, we present a detailed analysis of idle listening time factors on the ContikiMAC. Then, we propose Light Weight CCA(LW-CCA) as an extension to ContikiMAC to reduce power consumption by reducing the radio check time in receive mode WakeUp’s, while maintaining up to 99% the Packet Delivery Rate (PDR). The simulation results show that the proposed method reduces significantly energy consumption in nodes compared to ContikiMAC and thus it helps maintain a high network performance.

The way people innovate and create new ideas and bring them to the market is undergoing a fundamental change from closed innovation to open innovation. Why and how do firms perform open innovation? Firms’ open innovation is measured through the levels of firms’ joint patent applications. Next, we analyze network structures and characters of firms’ joint patent applications such as betweenness and degree centrality, structure hole, and closure. From this research, we drew conclusions as follows. First, the structure of collaboration networks has both direct and indirect effects on firms’ innovative performance. Second, in the process of joint patent applications, there is a long tail phenomenon in networks of joint patent applications. Third, the number of patents and International Patent Classification (IPC) subclasses together constitute a meaningful measure of the innovation performance of firms.

The central nervous system (CNS) is the final frontier in drug delivery because of the blood-brain barrier (BBB), which poses significant barriers to the access of most drugs to their targets. Kynurenic acid (KYNA), a tryptophan (Trp) metabolite, plays an important role in behavioral functions and abnormal KYNA levels have been observed in neuropsychiatric conditions. The current challenge lies in delivering KYNA to the CNS owing to its polar side chain. Recently, C-3 side chain modified KYNA analogs have been shown to cross the BBB; however, it is unclear whether they retain the biological functions of the parent molecule. This study examined the impact of KYNA analogs, specifically SZR-72, SZR-104, and the newly developed SZRG-21, on behavior. The analogs were administered intracerebroventricularly (i.c.v.), and their effects on the motor domain were compared with those of KYNA. Specifically, open field (OF) and rotarod (RR) tests were employed to assess motor activity and skills. SZR-104 increased horizontal exploratory activity in the OF test at a dose of 0.04 μmol/4 μL, while SZR-72 decreased vertical activity at doses of 0.04 and 0.1 μmol/4 μL. In the RR test, however, neither KYNA nor its analogs showed any significant differences in motor skills at either dose. Side chain modification affects affective motor performance and exploratory behavior, as the results show for the first time. In this study, we showed that KYNA analogs alter emotional components such as motor-associated curiosity and emotions. Consequently, drug design necessitates the development of precise strategies to traverse the BBB while paying close attention to modifications in their effects on behavior.

This study aimed to explore the feasibility of using airborne acoustic emission in laser beam butt welding for the development of an automated classification system based on neural networks. The focus was on monitoring the formation of joint gaps during the welding process. To simulate various sizes of butt joint gaps, controlled welding experiments were conducted, and the emitted acoustic signals were captured using audible to ultrasonic microphones. To implement an automated monitoring system, a method based on short-time Fourier transformation was developed to extract audio features, and a convolutional neural network architecture with data augmentation was utilized. The results demonstrated that this non-destructive and non-invasive approach was highly effective in detecting joint gap formations, achieving an accuracy of 98%. Furthermore, the system exhibited promising potential for low latency monitoring of the welding process. The classification accuracy for various gap sizes reached up to 90%, providing valuable insights for characterizing and categorizing joint gaps accurately. Additionally, increasing the quantity of training data with quality annotations could potentially improve the classifier model's performance further. This suggests that there is room for future enhancements in the study.