Yttria stabilized zirconia (Y-TZP) ceramics with drastically reduced yttria content have been introduced by different manufacturers aiming at improving the damage tolerance of ceramic components. In this study an alumina doped 1.5Y-TZP was axially pressed, pressureless sintered in air at 1250–1400 °C for 2 h and characterized with respect to mechanical properties, microstructure and phase composition. The material exhibits a combination of high strength of 1000 MPa and a high toughness of 8.5–10 MPa√m. The measured fracture toughness is, however, extremely depending on measurement protocol. Direct crack length measurements overestimate toughness due to trapping effects. The initially purely tetragonal material has a high transformability of > 80 %, the transformation behavior is predominantly dilatoric, measured R-curve related toughness increments are in good agreement with transformation toughness increments derived from XRD data.

In order to achieve better knowledge of the thermal barrier coatings (TBCs) by supersonic atmospheric plasma spraying (SAPS) process, an experimental study was carried out to elaborate physicochemical properties of particles in-flight during the SAPS process. One type of commercially available agglomerated and sintered yttria-stabilized-zirconia (YSZ) powders were injected into the SAPS plasma jet and collected by shock chilling method. The YSZ particles in-flight physicochemical properties of the melting state, morphology, microstructure, particle size distribution, element composition changes and phase transformation during the SAPS process have been systematically analyzed. The melting state, morphology and microstructure of the collected particles were determined by scanning electron microscopy (SEM). The particle size distribution was measured by a laser particle size analyzer (LPSA). Element compositions were quantitatively analysed by an electron probe X-ray microanalyzer (EPMA). Additionally, the X-ray diffraction (XRD) method was used to analyse the phase transformation. The results showed that the original YSZ powders injected into the SAPS plasma jet were quickly heated and melted from the outer layer companied with breakup and collision-coalescence. The outer layer of the collected particles containing roughly hexagonal shaped grains exhibited a surface texture with high sphericity and the inside was dense with hollow structure. The median particle size was decreased from 45.65 μm to 42.04 μm. Besides, phase transformation took place and the content of zirconium (Zr) and yttrium (Y) element was decreased with the evaporation of ZrO2 and Y2O3.

The laser sintering process and modification of electrophoretic deposition (EPD) YSZ coatings on YSZ air plasma sprayed thermal barrier coatings (TBCs) were investigated. Ni-based superalloy was plasma sprayed using yttria-stabilized zirconia (YSZ) to perform thermal barrier coating with 400 μm thickness. The electrophoretic deposition (EPD) technique was used for depositing nanopowder of YSZ on the surface of YSZ TBCs. In this study, a technology of direct sintering the green EPD layer by laser beam was carried out. The best conditions of deposition YSZ overlay coating using DC current were obtained with applied voltage 40 V, deposition time 5 min, and suspension concentration 10 g/l. Iodine was added to the solutions as the stabilizing agent. To overcome the disadvantages of high sintering temperatures, laser sintering was taken as a new approach. Microstructures for all specimens were studied using Field Emission Scanning Electron Microscopy (FESEM) with EDS analysis. Surface roughness was investigated using AFM analysis and central line average (CLA). The results indicated that the morphology after the direct laser sintering of the EPD layer has a fine and controllable grain size, high hardness, and low roughness. Which is better than the direct laser on plasma-sprayed coatings.

The effect of ceria doping of (ZrO2)1-x(Sm2O3)x crystals on their phase composition, microhardness and fracture toughness has been studied. The (ZrO2)0.995-х(Sm2O3)х(СеО2)0.005 crystals (where x = 0.032, 0.037 and 0.04) have been grown using directional melt crystallization in cold skull. The phase composition and structure of the crystals have been studied using X-ray diffraction, TEM and Raman spectroscopy. The mechanical properties such as microhardness and fracture toughness have been studied using Vickers indentation. It has been shown that the (ZrO2)0.995-х(Sm2O3)х(СеО2)0.005 solid solution crystals contain both Се4+ and Се3+ ions. Phase analysis data suggest that СеО2 doping increases the tetragonality degree of the transformable t phase and reduces the tetragonality degree of the non-transformable t' phase as compared to the (ZrO2)1-x(Sm2O3)x crystals. As a result, the t→m phase transition triggered by the indentation-induced stress in the СеО2 doped crystals is more intense and covers greater regions. СеО2 doping of the solid solutions increases the fracture toughness of all the crystals studied whereas the microhardness of the crystals changes but slightly. СеО2 doping of the (ZrO2)1-х(Sm2O3)х solid solutions in the experimental concentration range does not improve the high-temperature phase stability of the crystals and does not prevent high-temperature degradation of their fracture toughness.

Double-walled carbon nanotube-yttria-stabilized ZrO2 nanocomposites are prepared by a mixing route followed by Spark Plasma Sintering. Incorporation of carbon at contents higher than 2 wt.% results in significantly lower friction coefficients, both against alumina and steel balls. Double-walled carbon nanotubes improve wear resistance and reduce friction without severe damage, contrary to multi-walled carbon nanotubes.

In this paper, the effect of microstructure on the thermal conductivity of plasma-sprayed Y₂O₃ stabilized ZrO₂ (YSZ) thermal barrier coatings (TBCs) is investigated. Nine freestanding samples deposited on aluminum-base superalloy are studied. Cross-section morphology such as pores, cracks, m-phase content, grain boundary density of the coated samples are examined by scanning electron microscopy (SEM) and electron back-scattered diffraction (EBSD). Multiple linear regressions are used to develop quantitative models which describe the relationship between the particle parameters, m-phase content and the microstructure such as porosity, crack-porosity, the length density of small-angle-crack and the length density of big-angle-crack. Moreover, the relationship between microstructure and thermal conductivity is investigated. Results reveal that the thermal conductivity of the coating is mainly determined by the microstructure and grain boundary density at room temperature (25 ℃) and by the length density of big-angle-crack, monoclinic phase content and grain boundary density at high temperature (1200 ℃).

Objective: To determine the effect of sandblasting before and after sintering on the surface roughness of zirconia and the micro-tensile bond strength of a pressable veneering ceramic to zirconia. Methods: Pre-sintered zirconia blocks (IPS e.max ZirCAD, Ivoclar Vivadent) were divided into a control group (CTR, no surface treatment) and four test groups of three specimens each: Pre-S-30, Pre-S-50, Pre-S-110 were sandblasted with 30µm SiO2, 50µm Al2O3 and 110µm Al2O3 particles respectively, before sintering, Post-S-30 was sandblasted with 30µm SiO2 after sintering. For each treatment, the surface roughness was measured (Ra, Perthometer M4P, Mahr Perthen). After sintering the zirconia blocks, a liner and a pressable ceramic (IPS e.max ZirPress, Ivoclar Vivadent) were fired. Sixteen micro-bars were obtained from each block and submitted to the micro-tensile bond strength (µTBS) test. Data were analyzed with one-way ANOVA. Any correlation between Ra and µTBS was evaluated (Sperman test). Results: Sandblasting before sintering with 110µm Al2O3 (Ra=3.44±0.44µm), 50µm Al2O3 (Ra=2.32±0.46µm), and 30µm SiO2 (Ra=1.22±0.22µm) resulted in significantly higher roughness than sandblasting after sintering with 30µm SiO2 (Ra=0.46±0.11µm). The highest µTBS was measured when the sintered zirconia was sandblasted with 30μm SiO2 (26.79±14.80 MPa), which was significantly different from that of specimens that were sandblasted before sintering (Pre-S-30=20.90±11.70; Pre-S-50=21.27±15.19; Pre-S-110=23.99±16.83) or were not treated (CTR=17.44±14.03). Conclusions: Sandblasting zirconia before sintering enhances the surface roughness proportionally to the particle size of the sand used. Sandblasting with 30µm SiO2 after sintering appeared to improve bonding between the veneering ceramic and zirconia. Clinical Significance: Sandblasting with 30µm SiO2 after sintering may improve bonding between veneering ceramics and zirconia, thus reducing ceramic fractures/chippings.

This paper mainly explores the feasibility of using desert sand (DS) and recycled aggregate in cement stabilized base. Recycled coarse aggregate (RCA) and DS serve as the substitutes of natural coarse and fine aggregates, respectively, in cement stabilized base. A four-factor and four-level orthogonal test is designed to analyze the unconfined compressive strength, splitting tensile strength, and compressive resilient modulus. Furthermore, this paper investigates the effects of cement content, fly ash (FA) replacement rate, RCA replacement rate, and DS replacement rate on the road performance of cement stabilized base composing of RCA and DS. The test results reveal that the performance of cement stabilized base with partial RCA instead of natural coarse aggregate (NCA) and partial DS instead of natural fine aggregate satisfy the road use. Meanwhile, DS is beneficial to improve the strength of cement stabilized base. The correlation and microscopic analyses of the test results imply the feasibility of applying DS and recycled aggregate to cement stabilized base. It is hoped that this paper can offer a solid theoretical foundation for promoting the application of DS and recycled aggregate in road engineering.

Reactions of quinones with compounds containing an amino group can produce a wide variety of addition or substitution products that depend on reactivity of both quinone and amino derivative. 6,7-Dichloropyrido[1,2-a]benzimidazole-8,9-diones undergo selective nucleophilic substitution reaction with different benzohydrazides and α-hydroxy-p-quinone imine derivatives stabilized by strong intramolecular hydrogen bond were isolated. Synthesized compounds represent a combination of several structural motifs: benzimidazole core fused with α-hydroxy-p-quinone imine which contains a benzamido fragment. The protonation/deprotonation processes were investigated in a solution using UV-Vis spectroscopy and 1H NMR titration experiment. X-ray crystallography analysis revealed a set of weak non-covalent interactions such as intra- and intermolecular hydrogen bonds and π-π stacking. Additionally, the redox behavior of 6,7-dichloropyrido[1,2-a]benzimidazole-8,9-dione and its p-imino derivative was investigated in acidic and neutral environment using cyclic voltammetry measurements. Cathode material based on 6,7-dichloropyrido[1,2-a]benzimidazole-8,9-dione could act as potential effective active electrode in aqueous electrolyte batteries, however further optimization is required.

Construction using earth materials demonstrates ecological sustainability using locally sourced natural materials and environmentally friendly demolition methods. In this study, the environmental impact of adding cement to soil materials for rammed-earth farmhouse construction in rural China was investigated and comparatively simulated using the One Click LCA database, focusing on the conflict between sustainability objectives and the practical aspects of cement addition. By analyzing how the addition of cement aligns with local construction practices and by addressing the debate surrounding the inclusion of cement in rammed earth construction, our objective is to provide insights into achieving a balance between the environmental impact and the pragmatic considerations of using cement in earthen building practices. Three local structure scenarios are evaluated via simulations: a cement-stabilized rammed earth wall, a fired brick wall, and a localized reinforced concrete frame structure. The quantitative environmental impacts are assessed, and the qualitative differences in adaptation, economic sustainability, and other factors are examined in the context of present-day development in rural China. The results show that the use of cement-stabilized rammed earth wall-supported structures is associated with higher embodied carbon emissions compared to structures supported by reinforced concrete frames and enclosed by brick walls; however, these emissions are lower than those for brick wall-supported structures, while effectively meeting the structural requirements. In addition, the use of cement-stabilized earth for perimeter walls simplifies material management and disposal throughout the building's life cycle, and the cost-effectiveness of cement has been found to be substantially greater than that of reinforced concrete frames and brick structures, improving economic viability and social acceptability, especially among low-income communities in rural areas.

The advent of zirconia ceramics with excellent mechanical, biomechanical and optical properties has made it an attractive metal-free substitute for titanium implants. Both animal and human studies have documented shortcomings with titanium implants. A review of the current literature on 3 iterations of zirconia implant designs has been challenging due to heterogeneous success data and limited follow-up. Zirconia implants hold promise for a new generation of dental implants, but technical developments are needed for design and material enhancements that will need to be validated by long-term rigorous studies.

The purpose of this finite element analysis (FEA) was to evaluate the stress experienced by both the prosthetic components and the bone in relation to varying cement thicknesses ranging from 20 to 60 μm, utilized in the attachment of a zirconia crown on a conometric cap. The study focused on two distinct types of implants (Cyroth and TAC, AoN Implants, Grisignano di Zocco, Italy) featuring a Morse cone connection. Detailed three-dimensional (3D) models were created to repre-sent the bone structure (cortical and trabecular) and the prosthetic components, encompassing the crown, cement, cap, abutment, and the implant. The two implants were placed in a 1.5 mm sub-crestal position and subjected to an inclined load of 200 N at 45° on the crown. The results re-vealed that an increase in cement thickness resulted in a reduction of von Mises stress on the cor-tical bone for both Cyroth and TAC implants, while the decrease in stress on the trabecular bone was relatively less pronounced. However, the TAC implant exhibited a higher stress field and de-formation in the apical area compared to the Cyroth implant. In summary, this study investigated the impact of cement thickness on stress transmission across prosthetic components and peri-implant tissues by means of FEA analysis, indicating that the 60 μm cement layer manifested higher stress values nearing the material strength limit.

Curcumin, a hydrophobic polyphenol compound derived from the rhizome of the Curcuma genus, has a wide spectrum of biological and pharmacological applications. Previously, curcumin nanoparticles with different stabilizers had been produced successfully in order to enhance solubility and per oral absorption. In the present study, we tested the anti-inflammatory effect of D-α-Tocopheryl polyethylene glycol 1000 succinate (TPGS)-stabilized curcumin nanoparticles in vivo. Lambda-carrageenan (λ-carrageenan) was used to induce inflammation in rats; it was given by an intraplantar route and intrapelurally through surgery in the pleurisy test. In the λ-carrageenan-induced edema model, TPGS-stabilized curcumin nanoparticles were given orally one hour before induction and at 0.5, 4.5, and 8.5 h after induction with two different doses (1.8 and 0.9 mg/kg body weight (BW)). Sodium diclofenac with a dose of 4.5 mg/kg BW was used as a standard drug. A physical mixture of curcumin-TPGS was also used as a comparison with a higher dose of 60 mg/kg BW. The anti-inflammatory effect was assessed on the edema in the carrageenan-induced paw edema model and by the volume of exudate as well as the number of leukocytes reduced in the pleurisy test. TPGS-stabilized curcumin nanoparticles with lower doses showed better anti-inflammatory effects, indicating the greater absorption capability through the gastrointestinal tract.

Preventing the occurrence of secondary caries serves as one of the significant issues in dental clinic, thus make it indispensable to improving the properties of conventional composite resin (CR) by developing a novel CR. In present study, two groups of experimental CRs loaded with different contents of fluoride-doped nano-zirconia fillers (25 wt% and 50 wt%) were fabricated. The surface topography, mechanical performance, fluoride release, antibacterial effect, aging property and cytotoxicity of the experimental CRs were evaluated subsequently. A uniform distribution of the F-zirconia fillers over the whole surface of resin matrix could be observed. The experimental CRs showed continuous fluoride release within 28 days, which was positively correlated with the content of F-zirconia fillers. Moreover, the amount of fluoride release increased in the acidic buffer. Addition of F-zirconia fillers could improve the color stability, wear resistance and microhardness of the experimental CRs, without reducing the flexure strength. Furtherly, the fluoride ions released continuously from the experimental CRs resulted in effective contact and antibacterial properties, while they showed no cytotoxicity. As a consequence, considerations can be made to employ this new kind of composite resin loaded with fluoride-doped nano-zirconia fillers to meet clinical requirements when the antimicrobial benefits are desired.

In this study, cement is used as the component that provides the stabilizing effect in order to evaluate the hardness and stability of loess soil. To assess the strength characteristics of loess soil reinforced with cement, samples were created with four different cement contents and three different curing times. The materials were put through a series of tests to determine their flexural strength, direct shear strength, indirect tensile strength, and unconfined compressive strength. An appropriate cement dosage was found, in addition to a durability index that could be used to quantify the effect of water absorption investigations on cement-stabilized loess. Both of these discoveries were made simultaneously. Analyses of investigations such as scanning electron microscopy (SEM) and energy dispersive X-ray fluorescence spectrometry (XRF) examinations were carried out so that the fundamental mechanics of the materials could be comprehended. According to the findings, the cohesion of cement-stabilized loess is significantly more sensitive to structure than the friction angle of the material, and the cohesion is responsible for the increase in shear strength after remolding. To get the desired level of strength, it is necessary to adjust the cement's proportions. In addition, as the curing period progresses, we see an increase in the cement-stabilized loess's resistance and stiffness. This is because of the interactions that take place between the structure and the mineral composition. It is believed that this event was caused by the cementation that occurs naturally. As a consequence of this reaction, the production of new cementitious materials takes place. The cation exchange that causes the hydration and pozzolanic reaction that leads to the creation of aggregates and interparticle flocculation is responsible for their production. These findings suggest that cement may be utilized as a simple and effective method of loess stabilization, which will ultimately result in improved performance of the loess.

Aseptic implant loosening after total joint replacement is partially influenced by material-specific factors when cobalt-chromium alloys are used, including osteolysis induced by wear- and corrosion products, and stress shielding. Here, we aim to characterize a hybrid material consisting of alumina-toughened zirconia ceramics (ATZ) and additively manufactured Ti-35Nb-6Ta (TiNbTa), joined by a glass solder. The structure of the joint, static and fatigue shear strength, the influence of accelerated aging, and the cytotoxicity using an elution assay with human osteoblasts is characterized. Furthermore, the biomechanical properties of functional demonstrators of a femoral component for total knee replacements are evaluated. TiNbTa-ATZ specimens showed a homogenous joint with statistical distributed micro-pores and a slight accumulation of Al-rich compounds at the glass solder-TiNbTa interface. The static shear strength was 26.4 ± 4.2 MPa (Ti-ATZ reference: 38.2 ± 14.4 MPa, p = 0.117), all specimens survived 107 cycles of shear loading to 10 MPa, and aging did not reduce the strength. TiNbTa-ATZ did not impair the proliferation and metabolic activity of human osteoblasts. Functional demonstrators of TiNbTa-ATZ provided a maximum bearable extension-flexion moment of 40.7 ± 2.2 Nm. Biomechanical and biological properties of TiNbTa-ATZ demonstrate potential application for endoprosthetic implants.

Research on titanium oxo complexes (TOCs) are usually focused on their structure and photocatalytic properties. Findings from these investigations spurred our interest in exploring also their potential biological activities. In this study, we focused on the synthesis and structure of a compound with the general formula [Ti8O2(OiPr)20(man)4] (1), which was isolated from the reaction mixture of titanium(IV) isopropoxide with mandelic acid (Hman) in a molar ratio of 4:1. The structure (1) was determined using single-crystal X-ray diffraction, while spectroscopic studies provided insights into its physicochemical properties. To assess the potential practical applications of (1), its microcrystals were incorporated into a polymethyl methacrylate (PMMA) matrix, yielding composite materials of the type PMMA + (1) (2 wt.%, 5 wt.%, 10 wt.%, and 20 wt.%). The next stage of our research involved the antimicrobial activity evaluation of the obtained materials. Investigations carried out demonstrated antimicrobial activity of pure (1) and its composites (PMMA + (1)) against both Gram-positive and Gram-negative strains. Furthermore, MTT tests conducted on the L929 murine fibroblast cell line confirmed the lack of cytotoxicity of these composites. Our study identified (1) as a promising antimicrobial agent, also for producing composite coatings.

Batch and transport experiments were used to investigate the remediation of a loamy sand soil contaminated with Cr(VI) using zero valent iron nanoparticles (nZVI) stabilized by the carboxy methyl cellulose (CMC-nZVI). The effect of pH, ionic strength (IS), and flow rate on the removal efficiency of Cr(VI) were investigated under equilibrium (uniform transport) and non-equilibrium (Two-site sorption) transport using the Hydrus-1D model. The overall removal efficiency ranged from 70 to over 90% based on the chemical characteristics of the CMC-nZVI suspension and the transport conditions. The concentration and pH of the CMC-nZVI suspension had the most significant effect on the removal efficiency and transport of Cr(VI) in the soil. The average removal efficiency of Cr(VI) was increased from 24.1 to 75.5% when the concentration of CMC-nZVI nanoparticles was increased from 10 to 250 mg L-1, mainly because of the increased total surface area at larger particle concentration. Batch experiments showed that removal efficiency of Cr(VI) was much larger under acidic conditions. The average removal efficiency of Cr(VI) reached 90.1 and 60.5 % at pH 5 and 7, respectively. The Two-site sorption model described quite well (r2 = 0.96-0.98) the transport of Cr(VI) in soil as compared to the uniform transport model (r2 = 0.81-0.98). The average retardation of Cr(VI) was 3.51 and 1.61 at pH 5 and 7, respectively, indicating earlier arrival for the breakthrough curves and shorter time to reach maximum relative concentration at lower pH. The Hydrus-1D model has proven to be an efficient tool for assessing the removal of Cr(VI) pollutants, offering innovative, cost-effective, and environmentally friendly remediation methodologies.

The difficulties faced by the society in its goal of reducing mortality and improving the health status during the period of the COVID-19 pandemic showed that it is necessary to develop new approaches in the therapy of infectious diseases, leading to higher treatment efficiency and few side effects. The subject of the present study is the formation and characterization of the proper-ties of stable liposomes loaded with extracts from Bulgarian medicinal plants and monitoring their antiviral action against the human strain of coronavirus OC43 (HCoV-OC43) in vitro. The hydrodynamic diameter and -potential of the liposomes containing each type of payload were determined with DLS and electrokinetics. The encapsulated amount of extracts was evaluated against quercetin and gallic acid by using colourimetric methods. The BALB 3T3 Neutral Red Uptake (NRU) phototoxicity/cytotoxicity assay was used to estimate the safety of the compounds. For assessment of the antiviral activity against HCoV-OC43 of liposomes (Lip) containing medicinal plant extracts, the cytopathic effect inhibition test was used. Measurements of the virucidal activity and the effect on the virus adsorption stage was carried out using the endpoint dilution method, and ∆lgs were calculated by comparison with untreated controls. The estimated photo irritation factors (PIF) for the Lip containing extracts were < 2 which assigns them to the category of non-phototoxic substances. When the extracts were introduced into the liposomes as their carriers, the antiviral activity of the vesicles against the replication of HCoV-OC43 in vitro in-creased by several times compared to their individual activity described in our previous study. The determination of the effect of structures loaded with extracts on the extracellular virions and the stage of their adsorption to sensitive HCT-8 cells proved that the liposomes do not affect directly the viral surface or cell membrane, but only perform a function of carriers of the active substances and the observed result is due solely to the intracellular action of the extracts.

The world’s population is growing at a rapid pace, thus increasing the need for shelter, which, because of increased carbon emissions, is making our planet less inhabitable. Thus, supplementary cementitious materials (SCMs) are used to reduce the embodied carbon emissions in the building sector. Wood ash, as a replacement for cement in soil treatment, seems to be a promising material. In this study, we considered the strength, stiffness, and microstructural behavior of marine clay treated with cement and wood ash as a cement replacement. Since clay is abundant in nature, it could help stabilize waste to improve the mechanical behavior of produced composites. Portland cement (7%, 10%, and 13%) was replaced with various amount of wood ash (5% and 10%) with two different dry densities (1400 and 1600 kg/m3) and three distinct curing periods (7, 28, and 60 days). Unconfined compressive strength, direct shear, porosity, pulse velocity, x-ray diffraction, and scanning electron microscopy tests were performed on selected specimens to evaluate the structural and microstructural effect of clay–wood ash–cement interaction. The results revealed that the replacement of cement with 5% of wood ash yielded superior performance. The microstructure investigation of wood ash–cement–clay blends further showed the formation of a densified matrix with stable bonds. Furthermore, the porosity and strength properties of blends developed unique relationships, which were further confirmed by other supplementary materials and soils.

The present contribution is focused on the relation preparation – structure – optical properties of hybrid silica and zirconia powders containing Eu(III) complexes: [Eu(ntac)₃][pphendcn] and [Eu(phen)₂](NO₃)₃. Methods for functionalization of silica and zirconia microparticles, based on adsorption of 1,10-phenantroline and [Eu(ntac)₃][pphendcn], and doping with [Eu(phen)₂](NO₃)₃ nanoparticles are proposed to obtain of red emitting hybrid composites with quantum efficiency 20 – 50 %. The optical properties of rare earth ions incorporated in silica and zirconia composites are used to explore the site symmetry (D₂, C_2v or lower) of the Eu³⁺ optical centers in the hybrid composites. Quantum yields of the investigated sol-gel micropowders and quantification of their optical spectra are presented.

Marine clay deposits are commonly found worldwide. Considering the cost of dumping and the related environmental concerns, an alternative solution involving the reuse of soils that have poor conditions is crucial. In this research, the authors examined the durability of marine deposited clays and compiled a corresponding database. The use of slag alone as a binder, at any percentage, increased the accumulated mass loss (ALM) up to 2%. However, the use of lime as the third binder seemed to accelerate the chemical reactions associated with the hydration of clay and cementitious material and to enhance the chemical stability, i.e., samples that included both lime and slag experienced the same ALM as samples treated with cement only. Scanning electron microscopy analysis confirmed the durability improvements of these clays. The proposed unconfined compressive strength and accumulated mass loss relationship yielded practical approximation for the fine- and coarse-grained soils blended with up to three binders until 60 days of curing.

To investigate the effect of acidic nanoparticles on proton conductivity, permeability and fuel cell performance, a commercial Nafion® 117 membrane was impregnated with zirconium phosphates (ZrP) and sulfated zirconium (S-ZrO2) nanoparticles. The tensile test, water uptake, methanol crossover, Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Thermal gravimetric analysis (TGA) and Scanning Electron Microscopy (SEM) were used to assess the ca-pacity of nanocomposite membrane to function in a fuel cell. The modified Nafion® membrane obtained the higher water uptake and a lower water content angle than the commercial Nafion® 117 membrane, indicating that it has a greater impact on conductivity. Under strain rates of 40, 30 and 20 mm/min, the nanocomposite membranes demonstrate more stable thermal deterioration and higher mechanical strength, which offers tremendous promise for fuel cell applications. When compared to 0.113 S/cm and 0.013 S/cm, respectively, of commercial Nafion® 117 and Nafion® ZrP membranes, the modified Nafion® membrane with ammonia sulphate acid had the highest proton conductivity of 7.891 S/cm. When tested using a direct single cell methanol fuel cell, it had the highest power density of 183 m. cm-2 which is better than commercial Nafion® 117 and Nafion® ZrP membranes.

(1) Background: Prefabricated zirconia crowns are used to restore teeth in children. The purpose of this study was to evaluate the removal of these crowns with the erbium, chromium: yttrium-scandium-gallium-garnet (Er,Cr:YSGG) laser; (2) Methods: Twelve primary and 13 permanent teeth were prepared and prefabricated zirconia crowns were passively fitted and cemented with two resin modified glass-ionomer cements. Surface areas of prepared teeth and crowns were calculated. Crowns were removed using two laser settings: 4.5 Watts, 15 Hertz, 20 water/ 20 air, and 5 Watts, 15 Hertz, 50 water/50 air. The retrieval time and temperature changes were tested recorded. Data were analyzed using ANOVA with Tuckey’s adjusted post hoc pairwise comparison t-test; (3) Results: The average time for crown removal was: 3 minutes, 47.7 seconds for permanent; and 2 minutes 5 seconds for primary teeth. The mean temperature changes were 2.48℃ (SD=1.43) for permanent; and 3.14℃ (SD=1.88) for primary teeth. The time to debond was significantly positively correlated with tooth inner surface area and volume, outer crown volume, and the cement volume; (4) Conclusions: Use of the Er,Cr:YSGG laser is an effective, safe and non-invasive method to remove prefabricated zirconia crowns cemented with RMGI cements from permanent and primary teeth.

The chelating aluminum complex [2-(Me2NCH2)C2B10H10]AlX2 (X = Br 3, CH3 4) was synthesized using 2-dimethylaminomethyl-o-carboranyl lithium (2) with aluminum tribromide or dimethylaluminum bromide, resulting in a modest yield. Compound 4 was obtained by reacting compound 3 with CH3Li in toluene. All compounds were characterized by infrared (IR) spectroscopy, 1H, 11B, 13C nuclear magnetic resonance (NMR) spectroscopy, and X-ray crystallography. X-ray structural studies of CabNAlBr2 (3) and CabNAlMe2 (4) indicated that the Al atom was located at the center of a distorted tetrahedron. Crystal structures of the CabNAlBr2 (3) [a = 8.9360(3) Å, b = 12.0358(9) Å, c = 14.7730(4) Å, α = β = γ = 90°] and the CabNAlMe2 (4) [a = 8.9551(3) Å, b = 11.9126(9) Å, c = 14.7711(4) Å, α = β = γ = 90°] were obtained. The reactivity of aluminum complexes 3 and 4 with Lewis bases, such as H2O, pyridine, alkylamines, and arylamines, confirmed their rapid decomposition.

This study used eco-friendly materials known as Periwinkle Shell Powder (PSP) in stabilizing the engineering properties of lateritic soil. Preliminary test was performed on the un-stabilized lateritic soil for the purposes of identification and classification (natural moisture content, liquid limits, plastic limits, and plasticity index). The engineering tests were conducted on the lateritic soil stabilized with additions of (2, 4, 6, 8 and 10 %) PSP and OPC respectively. The result showed that cement gave a progressive increase in the Maximum Dry Density (MDD) of the lateritic soil from 1875 kg/m3 (2 %) to 2294 kg/m3 (10 %) respectively. This represents 22 % increase in the MDD from the un-stabilized state. For PSP, the Maximum MDD was attained at 6 % (1974 kg/m3), representing 5.3 % increase in MDD of the soil from the un-stabilized state. For both stabilizing agent, the Optimum Moisture Content (OMC) increases from 13.65 % to 13.83 % and from 11.72 % to 14.41 % for Cement and Periwinkle Shell Powder respectively. PSP recorded an increase of 5.6 % of CBR value compared with OPC that recorded an increase of 34 % CBR value. The study therefore concluded that Periwinkle Shell Powder (PSP) could be considered as good stabilizer for clayey or lateritic, and its uses as a stabilizer could also provide a big relief to the environmental pollution caused by its indiscriminate dumping.

A novel starch stabilized Mg/Al LDHs material (S-LDH) was prepared in a facile approach and its fluoride ion removal performance was developed. Characterization of S-LDH was employed by using XRD, FTIR and particle size distribution. The adsorption property was studied through the assessment of adsorption isotherms, kinetic models, thermal dynamics and pH influence. The result shows that a low loading of starch of 10 mg onto LDH could obviously improve fluoride removal rate. The S-LDH had 3 times higher adsorption capacity to fluoride than that of Mg/Al LDH to fluoride. The particle size was smaller and the particle size distribution was narrower for S-LDH than that for Mg/Al LDH. Langmuir adsorption isotherm model and pseudo-second-order kinetic model fitted well with the experimental data. In thermodynamic parameters, the enthalpy (△H0) value was 35.63 kJ mol-1 and the entropy (△S0) value was 0.0806 kJ mol-1K-1. The values of △G0 were negative, implying the adsorption process is spontaneous. S-LDH reveals stable adsorption property in a wide pH range from 3 to 9. The mechanism for fluoride adsorption on S-LDH included surface adsorption and interaction ion exchange.

Geopolymer is an emerging material alternative to Portland cement and has potential as a refractory material. Adding filler in geopolymer material is a strategy to increase the advantages of its physical and mechanical properties. It has been previously reported that adding nanoparticles can increase the compressive strength value, but there is no reported interaction between nanoparticles and geopolymer during the geopolymerization process. This study aims to study the effect of adding nano-zirconia fillers on the physical and mechanical changes of metakaolin-based geopolymers with nano-zirconia fillers. The geopolymer samples were made with 100 g of metakaolin as the base material and nano-zirconia in amounts of 2 gr, 5 gr, 10 gr, and 15 gr. Further characterization was carried out by XRD, FTIR, and SEM-EDX. This study showed that the compressive strength of the MZr05 sample increased significantly by 58.7% compared to the control sample. The test results of the structure and functional groups did not lead to any new compounds formed in the geopolymerization reaction. Therefore, the interaction of metakaolin geopolymer with nano-zirconia only creates an interfacial bonding.

Abstract: This work for the first time investigated the densification of multi-doping zirconia ceramic body with organic coating powders for solid electrolyte of solid oxide fuel cells via online imaging technology. The densification results show the initial stage plays a key role in the sintering. It can be found the covered organic PVA (polyvinyl acetate) supplies a potential kinetics to the initial densification during sintering. As a result, a kinetic function of densification in the initial stage was suggested. Furthermore, a novel sintering model with six sub-stages is developed for polycrystalline zirconia ceramics. The findings would be a valuable reference for predicting final temperature of sintering, the equivalent strain during the sintering process, as well as optimizing the densification behavior.

Zirconia has recently become one of the most popular dental materials in prosthodontics being used in crowns, bridges, and to implants. However, weak bonding strength of dental adhesives and resins to zirconia surface has been a grand challenge in dentistry, thus finding a better adhesion to zirconia is urgently required. Marine sessile organisms such as mussels use a unique priming strategy to produce a strong bonding to wet mineral surfaces; one of the distinctive chemical features in the mussel’s adhesive primer proteins is high catechol contents among others. In this study, we pursued a bioinspired adhesion strategy, using a synthetic catechol primer applied to dental zirconia surfaces to study the effect of catecholic priming to shear bonding strength. Catechol priming provided a statistically significant enhancement (P < 0.05) in shear bonding strength compared to the bonding strength without priming, and relatively stronger bonding than commercially available zirconia priming techniques. This new bioinspired dental priming approach can be an excellent addition to the practitioner’s toolkit to improve dental bonding to zirconia.

The objective was to compare the failure loads of glass ceramic, and polymer crowns against yttria-partially stabilized zirconia (Y-PSZ) crowns with varying yttria concentrations. Monolithic crowns of zirconia (Cercon XT, Katana UTML, BruxZir Anterior), glass ceramic (Celtra press, IPS e.max press, Lisi press), and polymeric materials (Trilor, Juvora, Pekkton) were fabricated and cemented to epoxy abutments. The total number of specimens was 135 for crowns and 135 for discs (15 specimens per material type and design). A universal testing machine was used to perform compressive loading of all crowns to failure with a steel hemisphere along the longitudinal axis of the abutments. Energy dispersive spectroscopy (EDS) was used to identify the concentration (mol% yttria-partially stabilized zirconia) for each zirconia brand. The data were analyzed using a generalized linear model and regression analysis. The results revealed significant differences (P < .05) in mean failure loads for different crown materials: Trilor (6811 ± 960 N) > Juvora (5215 ± 151 N) > Cercon (4260 ± 520 N) = BruxZir (4186 ± 269 N) = e.max (3981 ± 384 N) > Katana (3195 ± 350 N) = Lisi (3173 ± 234 N) = Pekkton (3105 ± 398 N) > Celtra (2696 ± 393 N). EDS showed that the zirconia materials contained yttria at different concentrations (BruxZir = 5Y-PSZ, Cercon = 4Y-PSZ, Katana = 3Y-PSZ). The yttria concentration had a significant effect on the failure load of the Katana (3Y-PSZ) crowns, which revealed lower failure loads than the Cercon (4Y-PSZ) and BruxZir (5Y-PSZ) crowns. New zirconia materials are provided with different yttria concentrations (3Y-, 4Y-, and 5Y-PSZ). Since a higher yttria concentration increases the translucency, clinicians should be aware that 4-5 wt% yttria-partially stabilized zirconia materials provide comparable or higher mechanical properties than e. max glass ceramic for dental application of crowns.

The development in the field of ceramics has been increasing over the past several decades. Among all of the dental ceramics, zirconia ceramics show very good mechanical properties and a significant improvement in mechanical function. However, it is properly established that each step of the fabrication process of zirconia ceramics must be controlled to achieve the expected mechanical properties. These steps include the block constructing, sintering process, machining and surface processing. Recent advances have focused on zirconia ceramics in forming and sintering processes, mechanical properties, combining with various materials, and on surface processing. All these items provide conceptions about the formability and machinability of the zirconia. Until now, very excellent studies have been done to specify the evolution of microstructures, phase and mechanical properties of zirconia ceramics during the sintering process. However, more studies are required in this field. This paper aims to demonstrate general views and various studies in the field of zirconia ceramics. The properties, applications and tests performed and the recent developments in the field of zirconia bioceramics are discussed.

Partially stabilized zirconia (PSZ) is a promising material with superior combination properties in a wide range of industries. In this study, the effect of grain size on the mechanical properties such as hardness, bending strength and fracture toughness (named as ‘indentation toughness’ in this study) was investigated. The multi-doped zirconia ceramics were prepared by powder processing and pressure-less sintered following four sintering schedules. The measured mechanical properties results show that the polymorph structure sintered at a higher temperature has a lower bending strength and hardness. But 300% more indentation toughness (30.54 Kg/mm) of samples sintered at 1600 °C +1150 °C relative to others was estimated due to the grain size effect by our suggested equation. By contrast, the fracture toughness was calculated with an existing method. The results showed that similar trends were obtained. It appeared to be a novel method for evaluating the toughness of partially stabilized zirconia ceramics with micron grains based on the size effect.

Nanocomposites consisting of cerium based nanoparticles stabilized by carboxymethyl cellulose (CMC) macromolecules were obtained using one-pot reaction at room tempera-ture. The characterization of the nanocomposites was carried out with the use of combina-tion of microscopy, XRD and IT-spectroscopy analysis. The type of crystal structure of in-organic nanoparticles corresponding to CeO2 has been determined and the mechanism of the nanoparticles formation was suggested. It was demonstrated that the size and shape of nanoparticles in the resulting nanocomposites does not depend on the ratio of the ini-tial reagents. Spherical particles with mean diameter 3 nm were obtained in different reac-tion mixtures. The scheme of the dual stabilization of CeO2 nanoparticles with carboxylate and hydroxyl groups of CMC. These findings are promising for the development and ap-plication of Ce-based nanoparticles materials.

This review provides informations and details for the fabrication of biosensors that are composed from lipid membranes and have been utilized and applied to rapidly detect food toxic compounds, environmental pollutants and analytes of clinical interest. Biosensors based on polymeric lipid membranes have been used to rapidly detect a wide range of these analytes and offer several advantages such as fast response, high sensitivity and selectivity, can be portable for in the field applications, and small size. A description of the construction of these devices and their applications for the rapid detection of food toxic substance, environmental pollutants and analytes of clinical interest is provided in this review.

It is necessary to address the scarcity of crushed stones for pavement structural layers. So fly ash can be proved to be promising solution as more than 270 tonnes of fly ash is generated in India. Though, numerous research has been conducted for the use of fly ash intreated and untreated form, high volume of fine particles and brittleness of the stabilized fly ash pose a great problem for its use in subbase and base. Moreover, stiffness or modulus of stabilized fly ash is vital elastic parameter which is used for mechanistic pavement design. Hence, in this study an extensive experimental investigation is carried out to study its strength and stiffness properties such as compressive strength, indirect tensile strength and flexural strength, cyclic indirect tensile modulus and flexural modulus of fiber reinforced cement stabilized fly ash, stone dust, aggregate mixtures. The stone dust and aggregates have been added to enhance the gradation of the composite’s mixture. The study presents the effect of fiber on strength and stiffness properties. The experimental result reveals that addition of polypropylene (PP) fibers up to 0.25 wt.% enhances the compressive strength and any further addition of fiber results in decrease of the strength. However, indirect tensile strength and flexural strength increases with increase in fiber percentage up to 0.5 wt.%. Cement content is observed to be the dominant parameter for stabilized materials. Suitable relationships have been developed between strength and modulus parameters for stabilized mixtures. Based on the strength and stiffness study, 70% fly ash and 30% stone dust-aggregate and 60% fly ash and 40% stone dust-aggregate with 6% cement can be considered for the base layer. Based on the indirect tensile strength and flexural strength behavior, 0.35% is considered as the optimum fiber percentage.

Additive manufacturing (AM) processes, including stereolithography (SL), can fabricate complex ceramic parts layer by layer using computer-aided design (CAD) models. A ceramic slurry with high solid loading is usually used in SL to fabricate the desired shape, which is further sintered to produce the final part. The traditional SL system utilizes a tank filled with printable material, known as a vat, which for ceramic slurry contributes several limitations and operational difficulties, and further renders it non-recyclable mainly due to its high viscosity and the fragility of the green state. In this study, we utilized a continuous film supply (CFS) printer integrated with a tape casting system using in-house-designed ceramic slurry to print standard prototype specimens. Various printing parameters, including viscosity, layer thickness control, and slurry recycling efficiency, were studied. In addition, post-processing optimizations of the prototype, characterizations, and the microhardness of sintered samples were studied to determine their properties and compare them with traditional methods. The effectiveness of slurry reusability was demonstrated by printing with original and recycled slurry to produce consistent densification of final parts. Post-processing was optimized to achieve a relative sinter density of 99.02% and microhardness of 12.59 GPa. This method provides new opportunities to realize dense complex ceramic features with final properties comparable to those produced by subtractive machining and traditional SL. Furthermore, slurry recycling helps to reduce the overall cost and material consumption.

A new one-pot technique for preparation of polysaccharide-based Pd- and Pd-Ag nanocatalysts by sequential supporting natural polymer (2-hydroxyethyl cellulose (HEC), chitosan (Chit), pectin (Pec)) and metals on zinc oxide was developed. The nanocatalysts based on polysaccharide were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer–Emmett–Teller (BET), infrared spectroscopy (IRS), X-ray powder diffraction (XRD), X-ray photoelectron spectra (XPS) and elemental analysis methods. The catalyst characterization results indicated complete adsorption of polysaccharide and metal ions on zinc oxide, forming polymer-stabilized Pd nanoparticles of ~2 nm in size, evenly distributed on the support surface. The catalysts were studied in the hydrogenation of 2-hexyn-1-ol under mild conditions (0.1 MPa, 40 °C). The catalysts demonstrated nearly the same conversion of 2-hexyn-1-ol. The selectivity to cis-hexen-1-ol of the catalysts decreases in the following order: 0.5%Pd-Ag(3:1)HEC/ZnO>0.5%Pd-Ag(3:1)Pec/ZnO>0.5%Pd-Ag(3:1)Chit/ZnO. The optimum reaction temperature and catalyst loading for the Pd-Ag catalysts modified with HEC and Chit have been determined (40 °C, 0.05 g).

The present study was aimed at revealing the influence of the mechanical stress induced by water molecules adsorption on the composition of crystalline phases in the ZrO2–3mol%Y2O3-nanoparticles. Three basic methods have been used to determine the phase transition: neutron diffraction, Raman microspectroscopic scanning, and X-ray diffraction. The fact of phase-structural β → α transformation and the simultaneous presence of two polymorphic structural modifications (β is the phase of the tetragonal syngony and α of monoclinic syngony in nanosized particles (9nm)) under normal physical conditions was established by these methods. Satisfactory consistency was achieved between the results obtained using different techniques.

This work is devoted to the study of active and stable nickel catalysts for methane dry reforming based on Pr-doped ceria-zirconia obtained by solvothermal continuous method. The studies of physicochemical and catalytic properties of the 5%Ni\Ce0.75Zr0.25-xPrxO2 series showed that Pr introduction leads to an increase in the amount of highly reactive oxygen of the oxide lattice. Praseodymium-based catalysts showed significantly higher reactant conversions. In addition to the nature of support, the method of nickel introduction was also studied - Ni was added both by impregnation and one-pot with mixed oxide preparation. The method of Ni addition was shown to have significant effect on the morphology of the supported active component and, respectively, on the catalytic activity. The 5%Ni/Ce0.75Zr0.15Pr0.1O2 catalyst prepared by one-pot method showed stable operation in the MDR reaction for 30 hours at CO2 and CH4 conversions of ~40% and an H2 yield of ~18% (Т=700°С, τ=10ms).

In this study, a parameter of volume stability was proposed for the first time to design polymorph zirconia ceramics used for special components. A series of heterogeneous polymorph zirconia ceramics with various amounts of monoclinic (M) phase were fabricated by two-step sintering. Samples with about 27%, 31%, and 51% M phase content were selected to study the properties. The thermal shock durability was found to be associated with thermal expansion behavior and noncritical micro cracks, which both based on M phase initial content. In good agreement with experimental results, the correlation of normalized K versus M phase initial content was established. It could provide a repeatable reference to prepare special zirconia components without loss of density.

Cu-ions dispersed on reduced graphene RGo prepared and characterized in a liquid state in ethanol. Either constant ultrasounds or a sequence of ultrasounds (15s working, 15s stop) were applied for 6 min or 2h overall time, at a power of 500 W. Commercial graphite in ethanol was introduced at a concentration of 0.04 g/mL and CuCl2 2.5 H2O concentrations between 0.012 and 0.04 g/mL were used. The structural characterizations performed by XRD, microscopic, and spectroscopic techniques, after a centrifugation at 5000 rpm applied 12 min before Cu-introduction, led to conclude that: 1) Without copper, negative peaks in UV spectra were detected with concentrated pure graphene solutions, indicating light emission as nicely confirmed next by fluorescence measurements, 2) After addition of copper chloride and equilibration for 2 min , very intense and narrow peaks of intensity larger than 10 were observed. These peaks due to collective excitations generating plasmons were suppressed at a higher dilution and also if the cell with one cm optical path was replaced by a narrower cell with a 0.2 cm path. When plasmons were suppressed, in the UV spectral range, a band gap due to the energy transition between the valence filled  orbitals and conducting empty * orbitals, was observed. The presence of Cu (II) and Cu (I) cations were evidenced by Visible NIR spectroscopy. The formed “green” liquors containing Cu (II) Cu (I) /graphene in ethanol were stable in air for months and had good photocatalytic visible properties as demonstrated by the decomposition of two dyes.

Peri-implantitis continues to be one of the major reasons for implant failures. We propose a new approach for incorporating MTA into Zirconia implant surfaces with Nd:YAG laser and investigate the biological response of peri-implant cells as well as the microbiological response. Discs of Zirconia stabilized with Yttria and Titanium were produced according 4 tested groups: Nd:YAG laser textured Zirconia coated with MTA (Zr MTA); Nd:YAG laser textured Zirconia (Zr Textured); Zirconia and Titanium discs (Zr and Ti ). Contact profilometry was used to evaluate surface roughness. Human osteoblasts, gingival fibroblasts and S. oralis were cultured on samples. Cell adhesion and morphology, cell viability, cell differentiation markers and bacterial growth were assessed. Zr Textured roughness was significantly higher compared to all other groups. Cellular adhesion was observed at 1 day in all samples in both cell lines. Osteoblasts viability was lower in Zr MTA group, unlike fibroblasts viability was shown to be higher in Zr MTA group compared to Zr Textured group at 3 and 7 days. Osteocalcin and IL-8 release by osteoblasts were higher in Zr MTA. Zr Textured showed higher IL-8 values released by fibroblasts. No differences in S. oralis CFUs were observed between groups. The results suggest that Zirconia implant surfaces coated with MTA seems to promote fibroblasts proliferation and osteoblasts differentiation, however does not appear to have antibacterial properties.

In previous studies regarding the osseointegration of zirconia (ZrO2) implants, a lack of consistency was observed in the surface topographies of the ZrO2 and Ti samples because of the difficult processability of ZrO2 surfaces. To resolve this problem, we used the molecular precursor method (wet process), which is a surface-modifying technique that can easily change the surface chemistry without changing the surface topography. A roughened Ti surface was prepared using sandblasting (large-grit) and acid treatment. We were able to create ZrO2-coated Ti implants with the same topography as that of roughened Ti substrates using the molecular precursor method, which solution contained a Zr complex. The uniform presence of tetragonal Zr was confirmed, and the apparent zeta potential of the surface of the ZrO2-coated Ti implant was higher than that of Ti. In animal experiments, ZrO2-coated Ti implants showed an equivalent or higher bone-to-implant contact ratio compared to that of the non-coated implants inserted into the femur bone defects of the rats. ZrO2 with the same surface topography as that of roughened Ti exhibits a promotion of osteogenesis equivalent to or better than that of Ti in the early stages of bone formation.

In this paper we demonstrate first ever dual-period diffraction gratings that do not require electrical tuning to obtain the effect of period change. Our method allows for multiplication of the base period by proper modification of the subsequent slits of the grating. The proposed elements are fabricated by selective photopolymerization of a composite based on nematic liquid crystal. The gratings are formed by polymer stabilization of liquid crystal in different orientations of the molecules in selected grating slits to allow for period manipulation. The operating principle is based on changing the phase delay introduced by the slits depending on polarization direction of incident light with respect to the director in each type of slit, which allows to change the grating’s period. The proposed technique was successfully utilized to obtain diffraction gratings with either doubling or tripling of the period.

Thymidylate synthase (TYMS) is an essential enzyme for the de novo synthesis of dTMP and has been a primary target for cancer chemotherapy. Although the physical structure of TYMS and the molecular mechanisms of TYMS catalyzing the conversion of dUMP to dTMP have been conducted thorough studies, oligomeric structure remains unclear. Here, we show that human TYMS not only exists in dimer but also octamer by intermolecular Cys43-disulfide formation. We optimize the expression condition of recombinant human TYMS using Escherichia coli system. Using HPLC-MS/MS, we show that purified TYMS has catalytic activity for producing dTMP. In the absence of reductant β-mercaptoethanol, SDS-PAGE and size exclusion chromatography (SEC) showed size of TYMS protein is about 35 KDa, 70 KDa, and 280 KDa. While the Cys43 was mutated to Gly, the band of ~280 KDa and the peak of octamer disappeared. Therefore, TYMS was determined to form octamer, dependent on the presence of Cys43-disulfide. By measuring Steady-State Parameters for monomer, dimer and octamer, we found the k_cat of octamer is increased slightly than monomer. On the basis of these findings, we suggest that octamer in the active state might have a potential influence on the design of new drug targets.

The aim of this study was to evaluate and compare the fracture resistance of definitive zirconia dioxide restorations obtained using a computer-aided design and manufacturing (CAD/CAM) system. Methods: Two groups of ten samples were analyzed for each material (n: 20), the first group was Zolid Gen X Amann Girrbach (ZGX) and the second group was Cercon HT Dentsply Sirona (CDS). The restorations were designed with identical parameters and milled with a CAD/CAM system. Each specimen was load tested at a speed of 0.5 mm/min with a direction parallel to the major axis of the tooth and with an initial preload of 10N until fracture using a universal testing machine (Universal/Tensile Testing Machine, Autograph AGS-X Series) equipped with a 20 kN load cell. The results obtained were recorded in Newtons (N), using software connected to the testing machine. Results: Statistically significant differences were found, and the fracture toughness of the monolithic zirconia crowns was lower in the CDS group (1744.84 ± 172.8 N), compared to the ZGX group (2387.41 ± 516 N). Conclusions: The monolithic zirconia CAD-CAM zirconia crowns showed sufficient fracture strength to be used in posterior molar and premolar zones with either material as they withstood fracture loads greater than the maximum masticatory force.

The phase composition design principle is introduced to obtain balanced properties of ionic conductivity and thermo-tolerant for zirconia solid electrolytes used in solid oxide fuel cells (SOFCs). The zirconia ceramic solid electrolytes are fabricated by two-step free sintering. With increasing Y/Mg ionic ratio from 1.78:1 to 1.88:1, the content of monoclinic phase fluctuates little (±3%). The ionic conductivity, including the total electrical resistance; grain electrical resistance and grain boundary electrical resistance at 1223K, are all gradually declining with the increasing of Y/Mg ionic ratio. Furthermore, the enrichment of Mg ion in grain boundary acts as a disincentive to grain boundary ionic conductivity. In addition, the maximum total equivalent conductivity at 1223K in this study reaches to 0.143 Scm-1 which can compare with that of certain YSZ. It will be beneficial to SOFCs application profited from increasing ionic conductivity of ceramic solid electrolytes.

Objective: The purpose of this study was to evaluate the surface texture and biofilm adhesion of veneered or CAD/CAM milled zirconia (partially stabilized with yttrium) after professional oral hygiene procedures. Samples (4x4 mm, thickness 2 mm; n = 72) were separated from zirconia blanks (3Y-TZP-LA). One group was veenired with ceramics and the other group of samples was CAD/CAM milled. Each group had 2 subgroups: polished and glazed. The samples were subjected to simulated strokes of professional brushing using abrasive paste and ultrasonic scaling. Parameters of surface micromorphology and receptivity to biofilm were calculated before and after simulating the given methods of professional maintenance of oral hygiene. The characteristics of zirconia surface were evaluated by scanning electron microscopy (SEM). Microbial bacterial/fungal species (Staphylococcus aureus, Streptococcus sanguinis and Candida albicans) were used and cultured on the respective sterilized zirconia surfaces. The amount of biofilm formation on zirconia surface was quantified by colony forming unit (CFU) counts. Results: SEM analysis showed the greatest change in surface microtopography after the use of ultrasonic scaling, in glazed zirconia samples. Less formation of colonies on the surface CAD/CAM milled zirconia restorations was observed. Conclusion: Routine methods of professional maintenance of oral hygiene can damage the surface of glazed zirconia restorations.

The search for graphene or few layer graphene production methods that are simple, allow mass production and yield good quality material continues to provoke intense investigation. The present work contributes through the study of the aqueous exfoliation of four types of graphene sources, namely graphite and graphite nanoflakes with different morphologies and geographical origin. The exfoliation was achieved in an aqueous solution of a soluble pyrene derivative that was synthesized to achieve maximum interaction with the graphene surface at low concentration (5 x 10-5 M). The yield of bilayer and few layer graphene obtained was quantified by Raman spectroscopic analysis and the adsorption of the pyrene derivative on the graphene surface was studied by thermogravimetric analysis and X-ray diffraction. The whole procedure was rationalized with the help of molecular modeling.

In this study, ignition delay and burning rate are experimentally investigated in relation to the effect of pristine carbon nanotubes (CNTs), sodium dodecylbenzene sulfonate (SDBS), and diesel blends. Single droplet combustion tests were conducted in a combustion system for 21 days using CNTs at concentrations of 50 ppm and 100 ppm, that were dispersed in Colombian commercial diesel and stabilized by SDBS. Additionally, recordings of the combustion were collected, and the Shadowgraph optical method was utilized for monitoring the evolution of droplet size during combustion. The measurements were done over a four-week period. The results demonstrated that the temporal stability has a direct impact on the single droplet combustion tests because a concentration of CNTs of 100 ppm showed higher stability than those achieved by 50 ppm. Consequently, improvements were found with a concentration of 100 ppm, for instance, thermal conductivity increased by about 20%, ignition delay time by 16.2%, and burning rate by 30.5%.

To investigate the role of sulfhydryl groups and disulfide bonds in different protein-stabilized emulsions, N-ethylmaleimide (NEM) was used as sulfhydryl-blocking agent to be added in the emulsion. The addition of NEM to block the sulfhydryl groups resulted in a reduction of the content of disulfide bonds formation, which enabled destruction of the internal structure of the protein molecule, and then decreased the restriction of protein membrane on the oil droplets. Furthermore, with NEM content increasing in the emulsion, a reduction of protein emulsifying activity and emulsion stability also occurred. At the same time, the intermolecular interaction of the protein on the oil droplet interface membrane was destroyed, and the emulsion droplet size increased with the NEM content in the emulsion. Although NEM blocking sulfhydryl groups not to form disulfide bonds has similar effects on three types of protein emulsion, the degree of myofibrillar protein (MP), egg-white protein isolate (EPI), and soybean protein isolate (SPI) as emulsifier had a subtle difference.

Immobilized metal ion affinity adsorbents have been widely used in separation technique to purify proteins. Due to the leakage of metal ion from the adsorbents, there is no metal ion affinity adsorbent for hemoperfusion has been applied to clinical trial. In this study, in order to prevent the leakage of Zn²⁺ loaded from cellulose beads based adsorbent, improve its stability and adsorption capacity for testosterone, Freeze-drying method was used to enhance the porosity of cellulose beads, improve the surface area of the cellulose beads and adsorption capacity for testosterone. Chitosan was used to coat the adsorbents for preventing the leakage of Zn²⁺ loaded and improve the adsorbent’s stability. Moreover, the factors affecting adsorption ability and some components in plasma were also investigated. The results indicate the adsorption ability of the adsorbent can be significantly improved by freeze-drying. After the adsorbent was coated with 0.02% chitosan solution, the highest adsorption percentage reached 48%. During adsorption, the Zn²⁺ concentration in plasma did not rise. In addition, the adsorption percentage for total proteins was below 15%. The results may be caused by the pore size and surface area of the adsorbent enlarged via freeze-drying, and the chitosan solution went into the pores and coated the outer and inner surface of the adsorbent. The adsorbent has a potential clinical application to remove testosterone in patients with recurrent and metastatic prostate cancer.

The study examined the effect of noninvasive crown retrieval/reuse process using erbium-doped yttrium aluminum garnet laser (Er:YAG). Twenty-six extracted human teeth were prepared for a crown. The crown was milled using lithium disilicate (LD) and zirconia (Z) materials, n=13 per group, 3 for scanning electron microscopy (SEM). The crown was luted using composite resin cement and subjected to a laser retrieval process. After the retrieval process, the crown was cleaned, recemented and laser-retrieved two more times, without and with additional tooth reduction mimicking clinical refreshment of dentin. Retrieval time and temperature were analyzed using analysis of variance (ANOVA). Surface changes were observed through SEM. The retrieval times were 267.1±130.43, 220±79.09, 277.1±126.44, 368.4±136.14, 355±159.39, and 419.2±121.36 seconds for first, second, third LD and Z groups, respectively (p=.009). The maximal temperatures were 23.95.1±1.89°C, 24.86±2.01°C, 24.17±1.53°C, 22.88±1.51°C, 24.03±1.74°C, and 21.99±1.32°C for for first, second, third LD and Z groups, respectively (p=.006). Er:YAG laser crown removal is an effective retrieval tool for all-ceramic crowns. Minimal changes to teeth and crowns were observed following laser irradiation.

Impact of Nitrogen Foamed Stimulation Fluids Stabilized by Nanoadditives on Reservoir Rocks of Hydrocarbon Deposits

In order to effectively utilize red mud and reduce its occupation of land resources as well as its impact on the environment, experiments were conducted to develop stabilized soil materials using nano-SiO2 synergistically modified red mud and to investigate the curing mechanism of stabilized soil. The unconfined compressive strength, microscopic morphology and curing mechanism of the red mud-based stabilized soil materials with different amounts of modified materials were investigated. The test results show that after 7-days curing, the unconfined compressive strength of red mud-based stabilized soil meets the compressive strength requirement of road base material when nano-SiO2, gypsum and cement are synergistically modified. In such case, the soil structure has the lowest fracture rate and the best structural compactness when the amount of nano-SiO2 is 1%; It is found that the needle-like and columnar calcium alumina in the modified red mud-based stabilized soil increases, and the binding energy of hydration product ions in the modified material is improved; The chemical curing mechanism of modified red mud-based stabilized soil includes hydration reaction, volcanic ash reaction, promotion effect of nano-SiO2, and enhancement effect of gypsum. On this base, a model of early start hydration process of red mud-based stabilized soil promoted by nano-SiO2 is established.

Accelerated degradation tests (ADT) are widely used in the manufacturing industry to obtain information on the reliability of components and materials, through degrading the lifespan of the product by applying an acceleration factor which causes damage to the material. The main objective is to obtain fast information which is modeled to estimate the characteristics of the material life under normal conditions of use and to save time and expenses. The purpose of this work is to estimate the lifespan distribution of gold nanoparticles stabilized with lipoic acid (GNPs@LA) through accelerated degradation tests applying sodium chloride (NaCl) as an acceleration factor. For this, the synthesis of GNPs@LA was carried out, a constant stress ADT (CSADT) was applied, and the non-linear Wiener process was proposed with random effects, error measures and different covariability for the adjustment of the degradation signals. The information obtained with the test and analysis allows us to obtain the life distribution in GNPs@LA, the results make possible to determine the guaranteed time for a possible commercialization and successful application based on the stability of the material. In addition, for the evaluation and selection of the model, the Akaike and Bootstraping criteria were used.

Zirconia-reinforced lithium silicate (ZLS) is utilized as a material for prosthetic tooth crowns, offering enhanced strength compared to other dental glass-ceramics. In this study, we investigate a commercial ZLS material, provided in a fully crystallized form. We examine the effects of an optional post-processing heat treatment on micro-contact damage using controlled indentation tests simulating the primary modes of contact during chewing: axial and sliding. Our findings indicate that the heat treatment does not affect mechanical properties such as the elastic modulus, hardness and indentation fracture toughness. However, it does enhance the resistance to contact damage by fracture and chipping in both axial and sliding modes, as well as the resistance to crack initiation measured from sliding tests. This improvement is attributed to the refinement of the flaw population achieved through the heat treatment. The results are analysed within the framework of contact and fracture mechanics, and the implications for prosthetic dentistry are briefly discussed.

The content of magnesium ions (Mg2+) in drinking water is relatively high and the excessive Mg2+ ingestion may lead to pathological lesions in human body system. At present, the detection of Mg2+ still relies on costly devices or/and complex organic fluorescence probes. To solve this problem, this work proposed a NaBH4-mediated co-reduction strategy for the synthesis of glutathione-stabilized bimetallic AuAg nanoclusters (GSH@AuAg NCs) with recognition performance to Mg2+. The preparation of GSH@AuAg NCs was simple and rapid and could be performed at mild conditions. The reaction parameters and sampling orders were optimized to understand the formation mechanism of GSH@AuAg NCs. The GSH@AuAg NCs exhibited a sensitive “light-on” fluorescence response to Mg2+ due to the re-molding of the interfacial physicochemical environment following the Mg2+ coordination, which affected the surface charge transfer process, and thus led to a novel method for fluorescence detection of Mg2+ with admirable selectivity for Mg2+. The proposed method showed a detection limit of 0.2 μM, and its practical utility for the detection of Mg2+ in real sample of purified drinking water was also demonstrated, confirming its practicability in monitoring the Mg2+ concentration in drinking water.

In order to effectively utilize red mud, an aluminum industrial waste, the stabilized soil material was developed using nano-SiO2 synergistically modified red mud, and the strength characteristics of the stabilized soil were analyzed to clarify the feasibility of such stabilized soil serves as a road base material. Through different combination schemes, the effects of different nano-SiO2 and cement contents on the strength of the stabilized materials were explored. The test results show that: in the synergistic modification of nano-SiO2 and cement, nano-SiO2 can significantly improve the early unconfined compressive strength of red mud-based stabilized soil; in the synergistic modification of nano-SiO2, gypsum and cement, the 7-d unconfined compressive strength of red mud-based stabilized soil is greater than 2 MPa, which meets the strength requirements of road base materials and shows the superiority of synergism. The nominal stress-strain curves are divided into five stages: compressed and compacted stage, elastic deformation stage, plastic deformation stage, damage deformation stage and residual deformation stage. The macroscopic compressive damage pattern of the specimens shows that the modified red mud-based stabilized soil mostly exhibits brittle damage.

Initial water content significantly affects the efficiency of soil stabilization. In this study, the effects of initial water content on the compressibility, strength, microstructure and composition of a lean clay soil stabilized by compound calcium-based stabilizer were investigated by static compaction test, unconfined compression test, optical microscope observations, environment scanning electron microscopy, energy dispersive X-ray spectroscopy and X-ray diffraction spectroscopy. The results indicate that as the initial water content increases in the range studied, both the compaction energy and the maximum compaction force decrease linearly and there are less soil aggregates or agglomerations, and smaller proportion of large pores in the compacted mixture structure. In addition, for specimens cured with or without external water supply and under different compaction degrees, the variation law of the unconfined compressive strength with initial water content is different and the highest strength value is obtained at various initial water contents. With the increase of initial water content, the percentage of oxygen element tends to increase in the reaction products of the calcium-based stabilizer, whereas the crystalline mineral of the soil did not change obviously.

Homogeneous water dispersions of MWCNTs were prepared by ultrasonication in the presence of an amphiphilic polystyrene-block-poly(acrylic acid) (PS-b-PAA) copolymer. The ability of PS-b-PAA to disperse and stabilize MWCTNs was investigated by UV-vis, SEM and zeta potential. It is shown that the copolymer can disperse nanotubes directly by sonication in water. The results show that the addition of a styrene block to PAA enhances the dispersion efficiency compared to pure PAA, possibly due to the nanotube affinity with the polystyrene moiety. Notably, the dispersions show an evident pH-responsive behavior, being MWCNTs reaggregation promoted in basic environment. Furthermore, composites obtained by drop casting display electrical conductivity responsive to pH variations, showing the potential of such materials for sensing applications.

The study examines the behavior of the Mechanically Stabilized Earth (MSE) wall using available reinforcement materials in Danang, Vietnam. The MSE was reinforced by the self-fabricated galvanized steel grids using CB300V steel with 3 cm ribs. The backfill soil is a sandy clay soil from the local area with a low cohesion. A full-scale model with full instrumentation was installed to investigate the distribution of tensile forces along the reinforcement layers. The highest load that caused the wall to collapse due to internal instability (reinforcement rupture) was 302 kN/m2, which is 15 times the design load of 20 kN/m2. The failure surface within the reinforced soil had a parabolic sliding shape which is similar to the theoretical studies. At the failure load level, the maximum lateral displacement at the top of the wall facing was small (3.9 mm) which is significantly lower than the allowable displacements for the retaining wall. Furthermore, a numerical model using FLAC software was applied to simulate the performance of the MSE wall. The modeling results are in good agreement with the physical model. Thus, the self-fabricated galvanized steel grids could be confidentially used in combination with the local backfill soil for the MSE walls.

The soil microbial community serves as a crucial indicator for assessing soil fertility and health. The composition and activity of soil microorganisms reflect the soil's well-being and its ability to provide proper nutrients for crops. Fertilization plays a prominent role in enhancing soil fertility, and novel types of fertilizers, such as stabilized fertilizers with nitrification/urease inhibitors and coated fertilizers, have gained popularity in rice and maize cultivation. However, the long-term effects of these stabilized and coated urea fertilizers on soil chemical properties, microbial di-versity and community structure, as well as nitrogen cycling functional genes, remain unclear. Therefore, it is essential to investigate the impact of extended use of stabilized and coated urea fertilizers on soil fertility and microbiota in rice paddy fields. This research will provide scientific and theoretical support for the development and promotion of stabilized and coated urea ferti-lizers. To examine the effects of long-term application of these stabilized and coated urea fertilizers on soil chemical properties and microorganisms in rice paddy fields, soil samples were collected from brown soil rice paddy fields treated with various urease and nitrification inhibitors, stable urea, sulfur-coated urea (SCU), and resin-coated urea (PCU). The study revealed that 16 years of long-term use of conventional urea nitrogen fertilizer led to a considerable reduction in soil TP. On the other hand, NBPT and conventional urea fertilizers, when applied for an extended period, significantly increased soil organic matter (SOM). Moreover, except for HQ and NBPT+DMPP, the prolonged application of new urea fertilizers also signifi-cantly enhanced soil total potassium (TK). Notably, among all the treatments, PCU treatment had higher values for various soil chemical properties. In the case of SCU fertilizer used in brown soil rice paddy fields, it resulted in a significant decrease in soil pH over time. However, this change in pH did not affect the population of ammonia-oxidizing bacteria (AOB), as it was primarily in-fluenced by soil available nitrogen. DMPP, HQ+DCD, NBPT+DMPP, SCU, and PCU significantly reduced the copy number of bacterial 16S rRNA genes in the soil, with the coated urea fertilizers (SCU and PCU) having a greater impact. The long-term use of stabilized urea fertilizers containing HQ significantly reduced the bacterial community in rice paddy soil. Conversely, HQ+DCD stable urea fertilizer significantly increased the population structure and abundance of Basidiomycota fungi while decreasing the population structure and abundance of Rozellomycota fungi. DMPP stabilized urea fertilizer notably increased the population structure and abundance of Ascomycota fungi while decreasing the population structure and abundance of Rozellmycota and Chytridiomycota fungi. Further-more, HQ stabilized urea fertilizer significantly reduced the population structure and abundance of Chytridiomycota fungi. It is important to note that SCU fertilizer is not suitable for long-term application in neutral to slightly acidic meadow brown soil with a background pH. On the other hand, stable urea fertilizers and resin-coated urea fertilizers containing HQ, NBPT, DCD, DMPP, and their combinations are suitable for long-term application in neutral to slightly acidic meadow brown soil.

Expansive soil shows dual swell-shrink which is not suitable for the construction. Several mitigating techniques exist to counteract the problem promulgate by expansive clayey soils. This paper explored the penitential mecho-chemical reinforcement of expansive clayey soil to mitigate the effect of upward swelling pressure and heave. The polypropylene fiber is randomly distributed in the soil for mechanical stabilization, and the industrial residual silica fume is used as a chemical stabilizer. The experimental analysis is made in three phases which involved the tests on mechanical reinforced expansive soil using randomly distributed polypropylene fibers with different percentages (0.25%, 0.50%, and 1.00%), and 12mm length. The second phase of experiments carried out on chemical stabilized expansive soil with different percentages (2%, 4% and 8%) of silica and next phase of the experimental focused in the combination of mecho-chemical stabilization of the expansive soil with different combination of silica (i.e., 2%, 4% and 8%) and polypropylene fibers (i.e., 0.25%, 0.50% and 1.00%). Maximum dry density (MDD), optimum moisture content (OMC), liquid limit (LL), plastic limit (PL), plastic index (PI) grain size, and constant volume swelling pressure test were performed on unreinforced and reinforced expansive soil to investigate the effect of polypropylene fiber and silica fume on the engineering properties of expansive clayey soil. The experimental results illustrate that the inclusion of polypropylene fiber has a significant effect on the upward swelling pressure and expansion property of expansive soil. The reduction in the upward swelling pressure and expansion is a function of fiber content. These results also indicated that the use of silica fume caused a reduction in upward swelling potential, and its effect was considerably more than the influence of fiber.

The COVID-19 pandemic has underscored the importance of swift responses and the necessity of dependable technologies for vaccine development. Our team previously developed a fast cloning system for the modified vaccinia virus Ankara (MVA) vaccine platform. In this study, we report the construction and preclinical testing of a recombinant MVA vaccine obtained using this system. We obtained recombinant MVA expressing the unmodified full-length SARS-CoV-2 spike (S) protein containing the D614G amino acid substitution (MVA-Sdg) and a version expressing a modified S protein containing amino acid substitutions designed to stabilize the protein a in a pre-fusion conformation (MVA-Spf). S protein expressed by MVA-Sdg was found to be expressed and correctly processed and transported to the cell surface, where it efficiently produced cell-cell fusion. Version Spf, however, was not proteolytically processed and despite being transported to the plasma membrane, it failed to induce cell-cell fusion. We assessed both vaccine candidates in prime-boost regimens in the susceptible transgenic K18-human angiotensin converting enzyme 2 (K18-hACE2) mice and in golden Syrian hamsters. Robust immunity and protection from disease was induced with either vaccine in both animal models. Remarkably, the MVA-Spf vaccine candidate produced higher levels of antibodies, a stronger T cell response, and a higher degree of protection from challenge. In addition, the levels of SARS-CoV-2 in the brain of MVA-Spf inoculated mice was decreased to undetectable levels. Those results add to our current experience and range of vaccine vectors and technologies for developing a safe and effective COVID-19 vaccine

The main objective is to offer a functionally coherent counter-narrative to the polarized views prevailing now about the complex ‘Eukaryogenesis problem’ versus the “primitive” nature ascribed to so-called “Prokaryotes” (termed Akaryotes herein). The paradigm shift presented aims at bridging the conceptual gap between the rudimentary beginnings of biomolecular cooperativity on a pristine Earth (the Origins of Life or OoL) and the beginnings of lineage-wise diversification toward Darwinean speciation in the Tree of Life (or ToL). Although the research field as a whole is not aware of a corresponding ‘Prokaryogenesis problem’, the evolutionary process resulting in the partly independent archaeal and bacterial cell types is not fully understood. The present paper provides an explanation for these problems based on coevolutionary complementarity at multiple levels. The unconventional model connects various stages from “neighborhood selection” in film-like layers of unbounded “surface protoplasm” based on short “statistical proteins”, via a closely knit “peptide/RNA partnership” in the “making of genes”, toward the “making of genomes” in several RNA-to-DNA transitions. Three virus-related plasmids carrying different DNA replicases may have initiated the vertical stability of hereditable lineages that led to the three “domains” of organismal life, with a fourth lineage ending in eukaryotic organelles. These partly independent transitions established DNA as a late-comer of fundamental biomolecules.

Milk serves as a crucial source of natural bioactive compounds essential for human nutrition and health. The gastrointestinal digestion of milk proteins releases various biologically active peptides that positively impact human health and enhance physiological performance. With the growing production of cheese, Greek yogurt, and other dairy products, the volume of unutilized acid whey is significantly increasing. Acid whey, containing almost all whey proteins and approximately one-quarter of casein, presents a valuable raw material for generating peptides with potential health benefits. These peptides exhibit properties such as antioxidant, antimicrobial, anti-inflammatory, anticarcinogenic, antihypertensive, antithrombotic, opioid, mineral-binding, and growth-stimulating activities, contributing to improved human immunity and the treatment of chronic diseases. Enzymatic hydrolysis of milk proteins has been developed as a method to produce these peptides, facilitating their use in food fortification. To incorporate whey into functional beverages, it undergoes fermentation by lactic acid bacteria with proteolytic activity. To specifically enrich these beverages with peptides exhibiting targeted bioactivities, it is essential to select lactic acid bacteria strains possessing the requisite protease profiles. Additionally, the sensory properties of the final product can be enhanced using starter cultures with diverse metabolic capabilities, even in the absence of added flavoring agents. Given the imperative to develop waste-free technologies and enhance the profitability of the dairy industry, there is a growing need to efficiently utilize and transform acid whey into a broad spectrum of valuable products and food additives. This approach is justified not only by the nutritional benefits of the bioactive components in whey but also by the commercial potential of safe and health-enhancing products.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

In order to shorten the detection time and improve the average precision on embedded devices, A lightweight and high accuracy model is proposed for passion fruit in complex environments (backlight, occlusion, overlap, sunny, cloudy, rainy). Firstly, replacing the backbone network of YOLOv5 with a lightweight GhostNet model reduces the number of parameters and computation while improving detection speed. Secondly, a new feature branch is added to the GhostNet network, and the feature fusion layer in the neck network is reconstructed to effectively combine the lower-level and higher-level features, which not only improves the accuracy of the model but also maintains its lightweight. Finally, the knowledge distillation methods are used to transfer the knowledge from the more capable teacher model to the less capable student model, which significantly improving the detection accuracy. The improved model is denoted as G-YOLO-NK. The average accuracy of the G-YOLO-NK network is 96.00%, which is 1.00% higher than the original YOLOv5s model. Furthermore, the improved model size is 7.14MB, reduced to half of the original model, and the real-time detection frame rate is 11.25 FPS on the Jetson Nano. Compared to the state-of-the-art model, the proposed model outperforms them in terms of average precision and detection performance. The present work provides an effective model for real-time detection of passion fruits in complex orchard scenes, which can provide valuable technical support for the development of orchard picking robots and greatly improve the intelligence level of orchards.

The Simultaneous Localization And Mapping (SLAM) scanner is an easy and portable Light Detection And Ranging (LiDAR) data acquisition device. Its main output is a 3D point cloud covering the scanned scene. Regarding the importance of accuracy in the survey domain, this paper aims to assess the accuracy of two SLAM scanners: the NavVis VLX and the BLK2GO Scanner. This assessment is conducted for both outdoor and indoor environments. In this context, two types of reference data are used: the Total Station (TS) and the static scanner Z+F Imager 5016. To carry out the assessment, four comparisons are tested: cloud to cloud, cloud to mesh, mesh to mesh, and edge detection board assessment. However, the results of the assessments confirm that the accuracy of indoor SLAM scanner measurements (5 mm) is greater than that of outdoor ones (between 10 mm and 60 mm). Moreover, the comparison of cloud to cloud provides the best accuracy regarding direct accuracy measurement without manipulations. Finally, based on the high accuracy, scanning speed, flexibility, and the accuracy differences between tested cases, it is confirmed that SLAM scanners are effective tools for data acquisition.

The impact of interaction SS with MJO on rainfall along Java Island to East Nusa Tenggara has been studied using daily rainfall observation data from 2140 weather observation stations, which are also equipped with GSMaP, OLR, and ERA5 data. There were 61 SS events found, 17 during active MJO and 44 in inactive MJO. Rainfall increases more in the western study area when the active MJO and more in the eastern study area when the inactive MJO is due to SS. SS reduces rainfall in the Jakarta region, regardless of the activity or inactivity of the MJO. SS causes extreme rainfall to only occur in a small part of certain areas, so it tends to significantly reduce the possibility of extreme rainfall. In the southern part of the IMC, SS predominates over MJO in supporting increased water vapor transport. Large-scale synoptic circulations like the monsoon, SS, and MJO can interact with local land-sea wind circulation to produce spatiotemporal variability in rainfall on Java Island. Rainfall mostly increases in the afternoon and decreases in the morning when SS occurs, whether there is MJO or not. Convective instability analysis indicates that SS increases precipitation, most likely by lowering CIN and raising VIMFC.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

Superior fiber quality is one of the most important objectives in cotton breeding. To detect the genetic basis underlying fiber quality, an F2 population containing 413 plants was constructed by crossing Jifeng 914 and Jifeng 173, both of which have superior fiber quality, with Jifeng 173 being better. Five fiber quality traits were investigated in the F2, F2:3, F2:4, and F2:5 populations. Quantitative trait loci (QTL) mapping was conducted based on a high-density genetic map containing 11,488 single nucleotide polymorphisms (SNPs) and spanning 4,202.12 cM in length. Transgressive segregation patterns and complex correlations in the five tested traits were observed. A total of 108 QTLs were found, including 27 for fiber length (FL), 16 for fiber strength (FS), 24 for micronaire (MC), 17 for fiber uniformity (FU), and 24 for fiber elongation rate (FE). Chromosome A7 contained 12 QTL, ranking the first. No QTL was found on chromosome D1 and D11. Each QTL contributed 1.98%–21.45% to the phenotypic variation (PV), including 13 major effect QTLs that contributed more than 10% toward PV. Two QTLs could be repeatedly detected in three populations, including qFL-D3-2 in F2, F2:4, and F2:5 with 9.18%–21.45% of PV, qFS-A11-1 in F2:3, F2:4 and F2:5 with 6.05%–10.41% of PV. Another seven stable QTLs could be detected in two populations, including four major effect QTLs: qFL-A12-3, qFS-D10-2, qMC-D6-2, and qMC-D8-1. Fourteen QTL-overlapping regions were found, which might explain the complex correlations among the five phenotypic traits. Four regions on chromosome A11, D3, D6, and D10 covered by both stable and major effect QTLs are promising for further fine mapping. The genomic regions of the two QTLs detected in three populations and the four major effect QTLs contain 810 genes. Gene functional analysis revealed that the annotated genes are mainly involved in protein binding and metabolic pathways. Fifteen candidate genes in the qFL-D3-2 region are highly expressed in fiber or ovules during fiber initiation, elongation, secondary cell wall thickening, or maturation stages. qRT-PCR revealed that Ghir_D03G005440.1 and Ghir_D03G011310.1 may play a role in promoting fiber initiation, Ghir_D03G006470.1 may be beneficial for promoting fiber elongation. This study provides more information for revealing the molecular genetic basis underlying cotton fiber quality.

Currently there are fewer depth models applied to pepper picking detection, while the existing generalized neural networks have problems such as large model parameters, long training time, and low model accuracy.In order to solve the above problems, this paper proposes a Yolo-chili target detection algorithm for chili pepper detection. First, the classical target detection algorithm yolov5 is used as a benchmark model, and an adaptive spatial feature pyramid structure combining the attention mechanism and the idea of multi-scale prediction is introduced to improve the model's detection effect on occluded peppers and small target peppers. Secondly, a three-channel attention mechanism module is introduced to improve the algorithm's long-distance recognition ability and reduce the interference of redundant testers. Finally, the quantized pruning method is used to reduce the model parameters and realize the lightweight processing of the model. Applying the method to the homemade chili pepper dataset, the AP value of chili pepper reaches 93.11%; the accuracy rate is 93.51% and the recall rate is 92.55%.The experimental results show that yolo-chili is able to achieve accurate and real-time pepper detection under complex orchards.

The temporary immersion system bioreactor named GreenTray®[2], [3]presents advantages over the existing ones. Firstly, there is no need to use forceps to move the shoots or plantlets in or out of the recipient, neither the use of scalpel to divide them. Secondly, the basis of the shoot can remain in the GreenTray® and can sprout again in several cycles of growth. These two characteristics reduce the costs in the process of micropropagation. Besides, shoots or plantlets development is enhanced by the aeration of the recipient, thus enriching with CO2 the recipient atmosphere. The chapter describes and provides images and values of interest in (1) the micropropagation process of some commercial Prunus or Pyrus rootstocks; (2) the plantlet growth under autotrophic conditions; and (2) the inoculation of plants with pathogens that reproduce in vitro the symptoms observed in vivo, using the GreenTray® bioreactor.

Aiming at the problems of inaccurate segmentation of long object and information loss of small object in real-time semantic segmentation algorithm, this paper proposes a lightweight multi-branch real-time semantic segmentation network based on BiseNetV2. The new auxiliary branch makes full use of spatial details and context information to cover the long object in the field of view. Meanwhile, in order to ensure the inference speed of the model, the asymmetric convolution is used in each stage of the auxiliary branch to design a structure with low computational complexity. In the multi-branch fusion stage, the alignment and fusion module is designed to provide guidance information for deep and shallow feature mapping, so as to make up for the problem of feature misalignment in the fusion of information at different scales, and thus reduce the loss of small target information. In order to further improve the model’s awareness of key information, a global context module is designed to capture the most important features in the input data. The proposed network uses NVIDIA GeForce RTX 3080 Laptop GPU experiment, on the road street view data set Cityscapes and CamVid average occurring simultaneously ratio reached 77.1% and 78.4% respectively, with running speed of 127 frames/s respectively and 112 frames/s. The experimental results show that the proposed algorithm can achieve real-time segmentation and improve the accuracy significantly, showing good semantic segmentation performance

In this paper we study a class of impulsive delayed neural networks with parameter uncertainties and reaction-diffusion terms. Using the properties of M-matrices and some inequality techniques, some sufficient conditions are derived to guarantee the global exponential stability of the given system. The results obtained are presented by simple algebraic inequalities, which are certainly more concise than previous methods. Finally, the validity and usefulness of our results are illustrated by arithmetic examples.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

Pyrops candelaria is one of the common pests of fruit trees, but the research on the pathogenic microorganisms it may carry is very limited. Therefore, it is essential to reveal the pathogenic microbes it carries and their potential hazards. This study found a new virus from the transcriptome of P. candelaria, which was first reported in P. candelaria and named as PyCaV (Pyrops candelaria associated virus). RACE and bioinformatics assay revealed that the full-length of PyCaV is 10855 bp with the polyA tail, containing a single open reading frame (ORF) encoding a polyprotein consisting of 3171 amino acid (aa). The virus has a typical Iflavirus structure, including two rhv domains, a RNA helicase domain (HEL), a 3C cysteine protease domain (Pro), and a RNA-dependent RNA polymerase domain (RdRp). Further phylogenetic analysis revealed that this virus belongs to family Iflaviridae and sequence alignements analysis suggedted PyCaV is new member in unassigned genus of family Iflaviridae. Further in-depth analysis of virus-infection-part showed that PyCaV is distributing in the whole longan lanternfly, including its head, chest, and abdomen, but more PyCaV was identified in the chest. The distribution of PyCaV in different parts of P. candelaria was further explored, which showed that more PyCaV were detected in its piercing-sucking mouthparts and chest viscera. Statistical analysis showed that the PyCaV infection was affected by time and locations.

With the burgeoning growth of online retail, the issue of counterfeit products has become a significant threat to both consumer trust and brand integrity, posing challenges to sustainable market practices. Online retail platforms are promoted to redesign their channel structures and enhance brand traceability to tackle counterfeits using blockchain technology. To investigate the interactions between blockchain technology and the channel structures of online retail platforms, we design a game theory model incorporating a manufacturer with(out) blockchain participation selling products via an online retail platform that operates an agency channel and/or a reselling channel. We show that the critical trade-off of blockchain participation comprises the brand assurance effect of the blockchain, the channel competition intensification effect, and the blockchain adoption cost. The platform is capable of strategically designing the channel structure to encourage (while discouraging) blockchain participation by the manufacturer. Our analysis highlights the complementarity between blockchain participation and the channel structure. Furthermore, the effect of the consumer’s belief in the reselling channel, the commission fee in the agency channel, and the substitutability between channels are investigated in depth. The research provides valuable insights for online retail platforms and policymakers seeking to foster a sustainable and trustworthy e-commerce ecosystem.

Apis mellifera, especially weak ones, are highly vulnerable to Carpoglyphus lactis mites, which can rapidly infest and consume stored pollen, leading to weakened colonies and potentially colony collapse. This study aimed to ascertain and investigate the prevalence of this mite in honeybee colonies across 9 provinces in the Republic of Korea (ROK). A total of 615 honeybee colonies were collected, from 66 apiaries during the spring and 58 apiaries during the summer of 2023. A 1,242 bp segment of the the Cytochrome c oxidase subunit 1 (COI) gene was amplified using the polymerase chain reaction method. The detection levels of C. lactis in the honeybees were compared between winter and summer. Based on the COI sequence analysis, the nucleotide sequence similarity of C. lactis mites isolated in the ROK with those from China (NC048990.1) was found to be 99.5%, and with those from the United Kingdom (KY922482.1) was 99.3%. This study is the first report of C. lactis in Korean apiaries. The findings in this study demonstrate a significantly higher detection rate in winter, which is 4.1 times greater than that in summer (p &lt; 0.001). Furthermore, the results underscore the usefulness of molecular diagnostic techniques for detecting C. lactis mites.

COX II containing a dual core CuA active site is one of the three core subunits of mitochondrial Cco, which plays a significant role in the physiological process. In this report, the full-length cDNA of COXⅡ gene was cloned from Sitophilus zeamais, which had an ORF of 684 bp encoding 227 amino acids residues. The predicted COXⅡ protein had a molecular mass of 26.2 kDa with pI value of 6.37, and multiple sequence alignment and phylogenetic analysis indicated that Sitophilus zeamais COXⅡ had high sequence identity 78.51% with the COXⅡ of other insect species, especially similarity to sitophilus oryzae. This gene was subcloned into the prokaryotic expression vector pET-32a, and induced by IPTG in E.coli Transetta (DE3) expression system. Finally the COXⅡ with 6-His tag was purified using affinity chromatography with Ni²⁺-NTA agarose. WB showed the recombinant COXⅡ was about 44 kD, and the concentration of fusion protein was 50μg/mL. UV-spectrophotometer and infrared spectrometer analysis showed that recombinant COXⅡ could catalyze the oxidation of substrate Cytc, and influenced by AITC. It was found that AITC could form a hydrophobic region with COXⅡ protein via molecular docking, besides, a sulfur atom of AITC structure could form a length of 2.9 Å hydrogen bond with Leu-31. These results will provide valuable information for elucidating the role of COXⅡ in Sitophilus zeamais responses to AITC, meanwhile, it will helpful to carry out a point mutation in AITC binding sites for the future research.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

The paper describes the new method for image compression based on coordinated group signal transformation. The algorithm is a type of difference coding. Coordinated processing significantly simplifies the difference signal conversion scheme using a single group codec for all signals. The described method considers color channels as correlated signals of a multi-channel communication system. The specifics of the processed data required modification of the coordinated group processing algorithm. First, we changed how to calculate the difference signals to prevent data loss. Secondly, the group codec was supplemented with a neural network to improve the quality of reconstructed images. We considered the following types of neural networks: fully connected, recurrent, convolution, and convolution in the Fourier space. Based on the simulation results, it is best to use fully connected neural networks if the goal is to minimize processing delay time. These networks have a response time of 13 ms. On the other hand, if the priority is to improve quality in cases where delays are not critical, then convolution neural networks in the Fourier space should be used. These networks have a response time of 140 ms and are of significant interest.

As the world population grows, fulfilling the need for biomaterials in the healthcare system becomes increasingly important. Biomaterials, which include metals, polymers, ceramics, and composites, play an important role in the creation of medical devices that improve people's lives. The European Society for Biomaterials described biomaterials as non-biological materials used in medical devices to interact with biological systems. This definition has developed to encompass materials that treat, assess, or replace tissues or bodily functions. Biocompatibility, as defined by the FDA, is a key feature of biomaterials, as is the requirement to fulfil design requirements such as mechanical performance, geometry, and electrical control. Over the last decade, advances in regenerative medicine and tissue engineering have boosted biomaterials' usage in medical applications dramatically. Despite its promise, scientists, engineers, and physicians continue to face significant challenges due to the complexity of biomaterials. Biomaterials have various benefits, including biodegradability, non-toxicity, and biocompatibility, making them extremely useful for replacing, sustaining, or improving biological activities in damaged tissues. They are used in a wide range of applications, including tissue engineering implants, human tissue healing and regeneration, medication delivery systems, and biosensors. This study gives insights into the fundamental characteristics, case studies, and ethical issues associated with the usage and use of biomaterials, further examining their potential and significance in healthcare and medicine.

The studied solar pot is a recent invention, which gained a utility model protection in 2021 from the Hungarian Intellectual Property Office under patent number 5489. The device is made for environmentally friendly cooking or heating (by utilizing solar energy) of foods and liquids. Its structure is similar to a double pipe heat exchanger, it has an outer mantle and an inner cooking tank. The goals of the paper are proposing a new physically-based mathematical model describing the solar pot and carrying out computer experiments with it, assembling an experimental system of the pot connected with a solar collector and performing measurements on it. Based on the results, the solar pot can successfully be used for cooking or sterilizing foods or liquids during the studied time period, in Hungary.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

This paper is focused on typical rural settlements in the Stara Planina Mountain area in Serbia. They are distinguished by their authenticity, identity and character, and they have still not been destroyed by inappropriate development as is the case in some other mountain areas in Serbia, where the effects of urbanization, globalization and homogenization are obvious. Consequently, there is a need to prevent these effects in mountain areas where there is a threat of disbalance between development and the inherited natural and cultural values. The paper starts from several important concepts that relate contemporary approaches to cultural heritage preservation, place morphology and planning future development. The concept definitions from recent documents from related fields are used. These concepts are then applied to the area of Stara Planina Mountain and its rural settlements. The necessity for an integrative approach to planning this area with significant natural and anthropogenic potential is pointed out, including its integration into international programs of sustainable development.

Abstract: Transcription factors are crucial pre-transcriptional regulatory mechanisms that can modulate the expression of downstream genes by binding to their promoter regions. DOF (DNA binding with One Finger) proteins are a unique class of transcription factors with extensive roles in plant growth and development. Our previous research indicated a decrease in iron content in chlorotic bamboo leaves. However, to our knowledge, genes related to iron metabolism pathways in bamboo species have not yet been studied. Therefore, in the current study, we identified iron metabolism-related (IMR) genes in bamboo and determined the transcription factors that significantly influence them. Among these, DOFs were found to have widespread effects and potentially significant impacts on their expression. We identified specific DOF members in Dendrocalamus latiflorus with binding abilities through homology with Arabidopsis DOF proteins, and established connections between some of these members and IMR genes using RNA-seq data. Additionally, molecular docking confirmed the binding interactions between these DlDOFs and the DOF binding sites in the promoter regions of IMR genes. The co-expression relationship between the two gene sets was further validated using q-PCR experiments. This study paves the way for research into iron metabolism pathways in bamboo and lays the foundation for understanding the role of DOF transcription factors in D. latiflorus.

The wetlands in northeastern Bangladesh are home to some of the most prolific and valuable ecosystems on the planet, offering a wide range of benefits to both the local and wider communities. A limited number of research on this topic have been carried out in various wetlands in coastal hilsa, but none have been located in the northeastern region of Bangladesh. Thus, the goal of this study was to better understand the most commercially relevant species (anadromous hilsa) in northeastern Bangladesh as well as to assess the wetland ecosystem services more thoroughly with the contribution of their fish genetic resources. In addition to laboratory studies, fieldwork was done in the fishing settlements along the Surma River, Hakaluki Haor, and Tanguar Haor. The study classified 77 fish species into 21 subcategories of ecosystem services, of which 56% were not threatened, 17% were vulnerable, and 10% were highly endangered. The species Hilsa was found to be the most economically significant, accounting for 1% of the GDP overall. The study determined if the hilsa stock of the examined wetlands maintains a single or several subpopulations in comparison to other parts of the country when they migrate from saline water to northeastern Bangladesh (freshwater). But when compared to other groups, the FST score was between 0.000 to 0.017, indicating that the populations are identical and that there is genetic material sharing between them. Additionally, these statistics imply that the Sylhet haor and adjacent river systems contain a single stock of Hilsa fish. Nevertheless, a number of stresses and risks, including overexploitation, illicit and destructive fishing, siltation, and natural disasters like flash floods, have been linked to changes in the supply of hilsa and other ecosystem services. This study also emphasizes the necessity of policy attention and research to address the concerns.

Severe acute respiratory syndrome coronavirus type 2 (SARS-CoV-2) continues to be a global threat due to its ability to evolve and generate new subvariants, leading to new waves of infection. Additionally, other coronaviruses like Middle East respiratory syndrome coronavirus (MERS-CoV, formerly known as hCoV-EMC) which first emerged in 2012, persists and continues to present a threat of severe illness to humans. The continued identification of novel coronaviruses, coupled with the potential for genetic recombination between different strains, raises the possibility of new coronavirus clades of global concern emerging. As a result, there is a pressing need for pan-CoV therapeutic drugs and vaccines. After extensive optimization of an HCV protease inhibitor screening hit, a novel 3CLPro inhibitor (MK-7845) was discovered and subsequently profiled. MK-7845 exhibited nanomolar in vitro potency with broad spectrum activity against a panel of clinical SARS-CoV-2 subvariants and MERS-CoV. Furthermore, when administered orally, MK-7845 demonstrated a notable reduction of viral burdens by &gt;6 log orders in the lungs of transgenic mice infected with SARS-CoV-2 (K18-hACE2 mice) and MERS-CoV (K18-hDDP4 mice).

The continuous casting process of helical fiber reinforced metal matrix composites was proposed, and the experimental equipment was designed and manufactured. The relationship model be-tween the process parameters and the helical shape of the fibers in the metal matrix is analyzed by differential geometry. Helical carbon fiber reinforced lead matrix composites were prepared under different conditions. When the melting temperature and cooling intensity were increased, the helical radius of helical carbon fiber in lead matrix was increased. When the fiber rotation speed was increased, the helical radius was decreased, and the helical pitch was de-creased proportionally. The experimental results are consistent with the process model. Carbon fiber rein-forced aluminum composites were prepared. Scanning electron microscopy showed that the infiltration between the aluminum matrix and the carbon fiber was not complete. As the volume fraction of carbon fiber which was added in composites is too small, the mechanical properties of the composites have not been significantly improved.

This article presents an innovative approach to the design of a safe adaptive backstepping control system. Tailored specifically for underactuated marine robots, the system utilizes simple sensors for enhanced practicality and efficiency. Given their operation in diverse oceanic environments fraught with various sources of uncertainties, ensuring the system's safe and robust behavior holds paramount importance in the control literature. To address this concern, this paper introduces a control strategy designed to ensure robustness at both the kinematic and dynamic levels. By emphasizing the compensation for the system uncertainties, the design integrates a straightforward fuzzy system structure. To further ensure the system's safety, a funnel surface is defined, followed by the design of a suitable nonlinear sliding surface as a function of the funnel and tracking error. Specifically leveraging the Lyapunov function, the study formally establishes the Semi-globally Practically Finite-time Stability of the closed-loop system, validated through simulations conducted on underactuated marine robots.

Several types of guided bone regeneration materials are available with various properties and clinical indications. Among them, dentin-derived matrix from extracted teeth is an excellent alternative to traditional graft materials, such as allografts and xenografts. Different clinical preparation protocols exist: block form versus powder form, demineralized versus non-demineralized form. Out of these methods, demineralization protocols for dentin-derived matrix from extracted teeth have been noted for a wide range of successful clinical outcomes. The purpose of this animal study was to find out the most effective method of demineralizing dentin-derived matrix to result in the highest regenerative ability in the bone graft material in rabbit calvaria. The study conducted a comparative histomorphometric analysis of four groups in distinguished matrix conditions: a control group without graft placement, a non-demineralized dentin-derived matrix graft placement group, a 15-minute demineralized dentin-derived matrix graft placement group, and a 30-minute demineralized dentin-derived matrix graft placement group. Regenerative processes were evaluated three times at 2, 4, and 8 weeks post-graft placement. These groups of rabbits were evaluated randomly in a blinded setting to prevent bias. Among the four groups compared, the group with a 15-minute demineralized dentin-derived matrix graft showed the most efficient bone regeneration in the histomorphometric analysis. Based on this animal study, it was apparent that a 15-minute demineralization of dentin-derived matrix is the preferred preparation protocol to maximize the regenerative potential in the matrix.

Promoting green development has become an important way to optimize the ecological and economic structure and promote sustainable development. The Yangtze River Economic Belt is an important economic corridor in China, and it remains to be examined whether the implementation of environmental regulations has enhanced the green total factor productivity (GTFP) of cities. This paper calculates the green total factor productivity of 107 cities within the Yangtze River Economic Belt by using the super-efficient SBM model and the GML index with Chinese city panel data from 2007-2019 and measures the intensity of environmental regulations through textual analysis. The bidirectional fixed-effects model constructed in this paper suggests an inverted U-shaped relationship between environmental regulation and GTFP, which is confirmed by a series of robustness tests. Green technology innovation and advanced industrial structure play a mechanism role in this. In regions with lower levels of green technology and industrial structure, the inverted U-shaped relationship between environmental regulation and green total factor productivity is more significant. In addition, the phenomenon of GTFP rising and then falling because of environmental regulation is more obvious in cities in the middle and upper reaches of the Yangtze River and outside the urban agglomerations. Therefore, when formulating environmental regulation policies, it is necessary to balance the relationship between economic development and environmental protection and harmonize the environment and economic development of the entire Yangtze River Basin.

Cocoa (Theobroma Cacao, L.) represents an important market that gained relevance and became an esteemed commodity thanks to cocoa powder, chocolate, and other related products. This work has analyzed 59 cocoa powder samples from the European market. Three distinct subgroups were identified: organic or conventional, alkalized or not alkalized, and raw or roasted processing. The impact of the technological process was evaluated on the pH, color, and compositional traits, as content of biogenic amines and salsolinol. The phenolic fraction was also investigated trough both common and emerging methods. Results depict that the influence of the agronomical practices (organic/conventional) did not affect significatively (p&lt;0.05) the composition of cocoa powders; similarly, the roasting process was not discriminative for the compounds traced. On the other hand, the alkalinization process greatly impacted on color, and pH, no matter of cocoa provenience, obtention, or other processes, also resulting reducing the phenolic fraction of treated samples. Principal components analysis confirmed that the alkali process acts on pH, color, and phenolic composition, but not on other bioactives molecules (BAs and salsolinol). All samples resulted safe while alkalized powders have a great reduction in beneficial biocompounds. A novel strategy could be to emphasize non-alkalized powders in the label, to meet the demand for more beneficial products.

Oral squamous cell carcinoma (OSCC) is a highly prevalent and aggressive malignancy, with mortality rates that reach 60%, mainly due to an excessive diagnostic delay. MiRNAs, a class of crucial epigenetic gene-expression regulators, have emerged as potential diagnostic biomarkers, with >200 molecules reported to be dysregulated in OSCC. We had previously established an in silico methodology for the identification of the most disease-specific molecules by bridging genetics and epigenetics. Here, we identified the stage-specific miRNAs that govern the asymptomatic early stages of oral tumorigenesis by exploiting the reverse interplay between miRNA-levels and their target-genes’ expression. Incorporating gene expression data from our group’s experimental hamster model of sequential oral oncogenesis, we bioinformatically detected the miRNAs that simultaneously target/regulate >75% of the genes that are characteristically upregulated or downregulated in the consecutive stages of hyperplasia, dysplasia and early-invasion OSCC, while exhibiting the opposite expressional dysregulation in OSCC-derived tissue and/or saliva specimens. We found that all stages share the downregulation of miR-34a-5p, miR124-3p, and miR-125b-5p, while miR-1-3p is underexpressed in dysplasia and early-invasion. Malignant early-invasion stage is distinguished by the downregulation of miR-147a and the overexpression of miR-155-5p, miR-423-3p and miR-34a-5p. The identification of stage-specific miRNA molecules may facilitate their utilization as biomarkers for presymptomatic OSCC diagnosis.