This paper provides an open dataset of measured energy use, solar energy production, and building air leakage data from a 328 m² (3,531 ft²) all-electric, zero energy commercial building in Virginia, USA. Over two years of energy use data were collected at 1-hour intervals using circuit-level energy monitors. Over six years of solar energy production data were measured at 1-hour intervals by 56 microinverters. The building air leakage data was measured post-construction per ASTM-E779 Standard Test Method for Determining Air Leakage Rate by Fan Pressurization and the United States Army Corps (USACE) Building Enclosure Testing procedure; both pressurization and depressurization results are provided. The architectural and engineering (AE) documents are provided to aid researchers and practitioners in reliable modelling of building performance. The paper describes the data collection methods, cleaning, and convergence with weather data. This dataset can be employed to predict, benchmark, and calibrate operational outcomes in zero energy commercial buildings.

The Energy Performance of Buildings Directive 2010 calls for the Nearly Zero Energy Standard for new buildings from 2021 onwards: Buildings using “almost no energy” are powered by renewable sources or energy produced by the building itself. For residential buildings, this ambitious new standard has already been reached. But for other building types this goal is still far away. The potential of these buildings to meet a Nearly Zero Energy Standard was investigated by analyzing ten case studies representing non-residential buildings with different uses. The analysis shows that the primary characteristics common to critical building types are a dense building context with a very high degree of technical installation (such as hospital, research and laboratory buildings). The large primary energy demand of these types of buildings cannot be compensated by building and property-related energy generation including off-site renewables. If the future Nearly Zero Energy Standard were to be defined with lower requirements because of this, the state related properties of Bavaria suggest that the real potential energy savings available in at least 85% of all new buildings would be insufficiently exploited. Therefore, it would be useful to instead individualize the legal energy verification process for new buildings to distinguish critical building types such as laboratories and hospitals.

Earth’s climate cannot be ignored any longer. Policies are vital in order to mitigate the negative effects of climate change. The energy crisis created by the Russo-Ukrainian war and pandemic affected the EU and its member states. The focus is more than ever on its energy policies and independence. The EU revised the energy strategy in response to Russia’s blackmail, and it sped up all the processes for energetic independence from Russia. This benefited the climate change policies the most, as all the measures involved reducing energy consumption and increasing renewables, thus contributing to reducing greenhouse gas emissions. As a member state of the EU, Romania is committed to complying with EU regulations. With a high degree of energy independence compared with the other EU members, Romania plans to become a regional energy provider and modernize the energy infrastructure internally as a response to Russia’s unprovoked aggression. The measures that the EU and Romania implemented after the war started in 2022 have come to fruition, and the effects are becoming visible a year later. This study aims to study the energy strategy of Romania in correlation with the EU strategy in the turbulent period of pandemics and war between 2019 and 2023, with the latest available data.

The energy efficiency of existing buildings is a crucial factor in addressing Europe’s energy con-sumption challenges, accounting for nearly 40% of the total energy usage. The ongoing energy crisis, driven by the reliance on fossil fuels and increasing prices, has underscored the urgency of adopting sustainable and energy efficient practices especially to the existing building stock. Cyprus is par-ticularly vulnerable due to its heavy dependence on imported fuels for electricity generation and faces significant challenges in transforming its existing building stock into energy-efficient and sustainable structures. Extensive focus has been made by the government on the energy-efficient retrofit of non-residential public buildings. This study examines an existing cultural hall. The case study of the Cultural Hall represents the building stock before 2010 which is lacking thermal in-sulation, double glazing and any energy efficient element. It then offers an ideal case study to ex-plore sustainable solutions which can be easily adopted from the construction industry and from the building owners. The primary objective of this research is twofold: first, to develop a comprehensive retrofit plan to transform the cultural hall into a net-zero energy building; and second, to explore how this transformation can give value back to the local community. After running two simulation scenarios and providing two energy performance certificates, one with at the existing state and one with the intended retrofit measures, it is clear that the building can be a net zero energy consump-tion building. Some interesting results derived, present also how this building can provide value back to the community i.e. through solar carports for EV charging.

This study reports an empirical analysis of an all-electric, Net Zero Energy Housing (NZEH) development located in a mixed-humid climate zone (4A, Virginia, USA). Circuit-level energy monitors were used to measure energy consumption and energy production data (solar photovoltaic) at 1-hr intervals in six identical apartments over 24 months. The study employs a multi-step case study methodology to a) empirically evaluate energy consumption and production data, b) identify the temporal variability of energy consumption and production data at different time scales, c) understand the impact(s) of weather and human-building interaction on energy consumption and production, and d) synthesize the study’s “lessons learned” toward data-driven recommendations for future NZEH researchers and practitioners. The study found that the development’s net zero energy goal was achieved in three of six case units and that NZEH housing performance was more influenced by human-building interaction than weather variability. The analysis also found the solar photovoltaic (PV) performance to be reliable across the sampled units over the periods of measurement, suggesting that solar PV could be oversized as an approach to overcome verifiability in HBI and achieve NZEH performance goals.

As argued by ‘Declaration of Concrete Environment (2010)’ of Korea and ‘Declaration of Asian Concrete Environment (2011)’ of six Asian countries, concrete as a single material has lately shown extremely large impact on environmental issues such as climate change. Assessment of environmental impact from concrete material and production has considerable importance. Concrete is a major material used in the construction industry that emits a large amount of substances with environmental impacts during its life cycle. Accordingly, technologies for the reduction in and assessment of the environmental impact of concrete from the perspective of Life Cycle Assessment must be developed. At present, the studies in relation to greenhouse gas emission from concrete are being carried out globally as a countermeasure against climate change. In this study, a sustainable concrete mix design algorithm was designed using correlation analyses, and its carbon emission and cost reduction performances were assessed. Using correlation analyses, the concrete strength, w/b and s/a ratios, and CO₂ emissions were identified as major variables of concrete mix design that influenced other variables. Also, this study aims to evaluate the CO₂ emission reduction performance of the algorithm-deduced sustainable concrete mix design, and therefore, the CO₂ emissions of the sustainable concrete mix design are compared with those of the actual concrete mix design applied to the construction of the office building A in South Korea.

The Upper Hunter Valley is a major coal mining area in New South Wales (NSW), Australia. Due to the ongoing increase of mining activities, PM10 (air-borne particle with an aerodynamic diameter less than 10 micrometres) pollution has become a major air quality concern in local communities. The early part of this study identified two air quality subregions in the valley. This paper aims to provide a holistic summarisation of the relationships between elevated PM10 pollution in two subregions and the local- and synoptic-scale meteorological conditions for spring and summer, when PM10 pollution is relatively high. A catalogue of twelve synoptic types and a set of six local meteorological patterns have been quantitatively derived and linked to each other using the self-organising map (SOM) technique. The complex meteorology-air pollution relationships have been visualised/interpretated on the SOM planes for two representative locations. It was found that the influence of local meteorological patterns differed significantly for mean PM10 levels vs the occurrence of elevated pollution events and between air quality subregions. In contrast, synoptic types showed generally similar relationships with mean vs elevated PM10 pollution in the valley. Two local meteorological patterns, the hot-dry-northwesterly wind conditions and the hot-dry-calm conditions, were found most PM10 pollution conducive in the valley when combined with a set of synoptic counterparts. These synoptic types are featured with the influence of eastward migrating continental high pressure system and westerly troughs, or a ridge extending northwest towards coastal northern NSW or southern Queensland from the Tasman Sea. The method and results can be used in air quality research for other locations of NSW, or similar regions elsewhere.

To enable net zero sustainable thermal building energy this study develops an open-source thermal house model to couple solar photovoltaic (PV) and heat pumps (HP) for grid-connected residential housing. The calculation of both space heating and cooling thermal loads and the selection of HP is accomplished with a validated Python model for air-source heat pumps. The capacity of PV required to supply the HPs is calculated using an System Advisor Model integrated Python model. Self-sufficiency and self-consumption of PV and the energy imported/exported to the grid for a case study are provided, which shows that simulations based on the monthly load profile have a significant reduction of 43% for energy sent to/from the grid compared to the detailed hourly simulation and an increase from 30% to 60% for self-consumption and self-sufficiency. These results show the importance of more granular modeling and also indicate mismatches of PV generation and HP load based on hourly simulation datasets. The back-calculation PV sizing algorithm combined with HP and thermal loads presented in this study exhibited robust performance. The results indicate this approach can be used to accelerate the solar electrification of heating and cooling to offset the use of fossil fuels in northern climates.

A comprehensive evaluation system of rural building energy consumption from a innovative composite perspective is established, which is suitable for southwest China. the brainstorming method and Delphi method were used to establish the indicator system, the ANP method was applied to calculate the weights of the comprehensive evaluation model, the scoring criteria of all evaluation indexes are constructed based on fuzzy evaluation theory, the applicability of the model is verified by an example of the countryside around Chengdu. The results showed that the score of some factors is low, whole or part area, just like the percentage of clean energy use(C24), the thermal performance of external walls(E21), the implementation of energy-saving measures(S22), were key factors affecting the target level, which has greater potential for improvement. The distribution of comprehensive indicators and evaluation factors have certain spatial distribution characteristics, the overall spatial distribution shows the characterwastic of "high in the southeast and low in the northwest". The key factors and spatial distribution characteristics found can be used as an important basis for the improvement of green energy-saving promotion measures, energy-saving retrofit programmes were proposed in terms of additional solar room, energy-saving of external walls and air-conditioning temperature setting guidance.

Owing to the large ratio of consumption in the building sector, energy saving strategies are required. Energy feedback is an energy-saving strategy that consumers to change their energy-consumption behaviors. The strategy has been principally focused on providing energy-consumption information. However, realization of energy savings using only consumption information remains limited. In this paper, a building-energy three-dimensional (3D) visualization solution is thus proposed. This solution includes the process of diagnosing a building and providing prediction of energy requirements if a building improvement is undertaken. Accurate diagnostic information is provided by real-time measurement data from sensors and building models using a close-range photogrammetry (CRP) method without depending on blueprints. The information is provided by employing visualization effects to increase the energy-feedback efficiency. The proposed strategy is implemented on two testbeds, and building diagnostics are performed accordingly. For the first testbed, the predicted energy improvement amount resulting from the facility upgrade is provided. The second testbed is provided with a 3D visualization of the energy information. The aim is to determine if the building manager will replace the facility after our recommendation is given to improve the building energy efficiency driven from the energy information. Unlike existing systems, which provide only ambiguous data that lack quantitative information, this study is meaningful because it provides energy information with the aid of visualization effects before and after building improvements.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

In this paper, the methodology using Insect Intelligent Building (I^2B) technology for establishing energy consumption monitoring system of public buildings is prevailed. The computing process node and distributed algorithm are utilized to implement the energy consumption collection and data transmission and data pre-processing. Taking a commercial building as a case study, CPNs are applied to set up the building energy consumption monitoring system, with the Spanning Tree Algorithm for generating network topology，and BPNN method for solving abnormal data and recovering missing data. The research results demonstrate the proposed method can effectively improve the performance of plug-and-play and self-identified and self-configuration of energy consumption monitoring system.

Densely urbanized areas, with a low percentage of green vegetation, are highly exposed to Heat Waves (HW) which nowadays are increasing in terms of frequency and intensity also in the middle-latitude regions, due to ongoing Climate Change (CC). Their negative effects may combine with those of the UHI (Urban Heat Island), a local phenomenon where air temperatures in the compact built up cores of towns increase more than those in the surrounding rural areas, with significant impact on the quality of urban environment, on citizens health and energy consumption and transport, as it has occurred in the summer of 2003 on France and Italian central-northern areas. In this context this work aims at designing and developing a methodology based on aero-spatial remote sensing (EO) at medium-high resolution and most recent GIS techniques, for the extensive characterization of the urban fabric response to these climatic impacts related to the temperature within the general framework of supporting local and national strategies and policies of adaptation to CC. Due to its extension and variety of built-up typologies, the municipality of Rome was selected as test area for the methodology development and validation. First of all, we started by operating through photointerpretation of cartography at detailed scale (CTR 1: 5000) on a reference area consisting of a transect of about 5x20 km, extending from the downtown to the suburbs and including all the built-up classes of interest. The reference built-up vulnerability classes found inside the transect were then exploited as training areas to classify the entire territory of Rome municipality. To this end, the satellite EO HR (High Resolution) multispectral data, provided by the Landsat sensors were used within a on purpose developed "supervised" classification procedure, based on data mining and “object-classification” techniques. The classification results were then exploited for implementing a calibration method, based on a typical UHI temperature distribution, derived from MODIS satellite sensor LST (Land Surface Temperature) data of the summer 2003, to obtain an analytical expression of the vulnerability model, previously introduced on a semi-empirical basis.

The paper is based on the research project P2Endure funded within the H2020-EE-2016-2017 call. The main aim of the research is to propose innovative solutions for deep renovation that are applicable and replicable for the widest range of building typologies, from public to residential and historic buildings. In this paper, the methodology adopted to perform the energy analyses and to verify the achievement of the expected targets in terms of savings is defined, based on a range of real case studies. The main aim is to promote a guideline for designers showing specific instruments to perform towards the attainment of the 60% threshold of the energy savings giving advice on how to further improve the energy performance of the buildings, basing on the overview of the energy analyses run for similar cases.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

Intermetallic compounds are increasingly being expected to utilize in tribological environments, but to date the works are hindered by insufficient ductility at low and medium temperature. This paper presents a novel multiphase intermetallic alloy with the chemical composition of Mo-40Ni-13Si (at.%). Microstructure characterization reveals that a certain amount of ductile Mo phases formed during the solidification process of ternary Mo-Ni-Si alloy melt, which is undoubtedly beneficial to the ductility improvement of intermetallic alloy. Tribological properties of the designed alloy, including wear resistance, friction coefficient and metallic tribological compatibility, were evaluated under dry sliding wear test conditions at room temperature. Results suggested that the multiphase alloy possesses an excellent property for room-temperature wear applications, which is attributed to the unique microstructural features and thereby good combination in hardness and ductility. The corresponding wear mechanism is also reported by observing the worn surface, subsurface and wear debris of alloy, which to be found is soft abrasive wear.

We present a review of the current state of the field for a rapidly evolving group of technologies related to solar energy harvesting in built environments. In particular, we focus on recent achievements in enabling the widespread distributed generation of electric energy assisted by energy capture in semi-transparent or even optically clear glazing systems and building wall areas. Whilst concentrating on the cutting-edge recent results achieved in the integration of traditional photovoltaic device types into novel concentrator-type windows and glazings, we compare the main performance characteristics reported with these achievable using more conventional (opaque or semi-transparent) solar cell technologies. A critical overview of the current status and future application potential of multiple existing and emergent energy harvesting technologies for building integration is provided.

The Upper Hunter Valley is a major coal mining area containing approximately 40% of the currently identified total coal reserves in New South Wales (NSW), Australia. Due to the ongoing increase of mining activities, PM10 (air-borne particle with an aerodynamic diameter less than 10 micrometres) pollution has become a major air quality concern in local communities. This paper summarises the spatial and temporal variability modes of PM10 pollution in the region, based on long-term multi-site monitoring data and the application of the rotated principal component analysis (RPCA) and wavelet analysis techniques. RPCA identified two distinct air quality clusters/subregions in the valley, one in the west/northwest, the other in the southeast. Wavelet analysis revealed the annual cycle to be most persistent temporal mode of PM10 variability in both subregions, with intermittent signals observed at time scales of around 120, 30~90 and under 30 days. How these variation modes are related to the effects of local PM10 emissions and the influence of meteorology at different time scales deserves further attention in future work. The findings will be used in air quality reporting and forecasting in NSW. The methodology and results can also be useful for air quality research in similar regions elsewhere.

Without an established energy management plan, human lifestyle improvement is incomprehensible. Adequate energy assets are the key to human lifestyle development, however, energy assets are restricted and exorbitant too. In this paper, an energy control system for a green environment called PMC (Power Management and Control) is proposed. The system is based on hybrid energy optimization, energy prediction, and multi-preprocessing. The blend of GA (Genetic Algorithm) and PSO (Particle Swarm Optimization) is utilized to make a fusion methodology to improve occupant comfort index (OCI) and decrease energy utilization. The main theme of the proposed PMC technique is to improve OCI and decrease energy utilization. The proposed framework gives better OCI when compared with its counterpart Ant Bee Colony along with Knowledge Base framework (ABCKB), GA-based prediction framework (GAP), Hybrid Prediction with Single Optimization framework (SOHP), and PSO-based power consumption framework. Compared with the existing AEO framework, the proposed PMC methodology gives practically the same OCI, but consumes less energy. The proposed PMC methodology additionally accomplished the most extreme OCI (i-e 1) when compared with the existing model FA-GA (i-e 0.98). The proposed PMC model consumed less energy as compared to existing models ABCKB, GAP, PSO and AEO. The proposed model consumed more energy than SOHP but provided better OCI. The comparative outcomes show the viability of the proposed PMC framework in lessening energy utilization and improving the OCI. Unlike other existing mythologies except for the AEO framework, the proposed PMC technique is additionally confirmed through a simulated climate by controlling indoor climate using actuators, like Fan, light, AC and boiler.

Plastic waste accumulation poses significant environmental challenges, underscoring the importance of closing the plastic life cycle by converting waste into valuable products. Pyrolytic char, a promising byproduct, offers diverse industrial applications. However, little attention has been given to converting hydrocarbon-based plastics into solid carbon due to their low fixed carbon content. This study compares sulfonation and thermal oxidation stabilization techniques for carbonizing waste polyethylene and polyvinyl chloride. Results indicate sulfonation yields higher pyrolytic char formation and improves surface properties, surpassing Al2O3 in catalyst support characteristics. Thermal oxidation increases fixed carbon content but adversely affects char yield and surface properties. Both methods effectively enhance fixed carbon content, but sulfonation emerges as more advantageous, suggesting potential use of plastic-derived char as a catalyst support material, contributing to circular economy development.

This work presents an innovative application of optimal control theory to the strategic scheduling of battery storage in the day-ahead electricity market, with a focus on enhancing profitability while factoring in battery degradation. The study incorporates in the optimisation framework the cost of battery capacity degradation, the effects of capacity degradation and internal resistance degradation into dynamics. We employ a continuous-time representation of the dynamics, in contrast with many other studies that use a discrete-time approximation with rather coarse intervals. We adopt an equivalent circuit model coupled with empirical degradation parameters to simulate a battery cell’s behaviour and degradation mechanisms with good support from experimental data. Utilising direct collocation methods with mesh refinement allows for precise numerical solutions to the complex, nonlinear dynamics involved. Through a detailed case study of Belgium’s day-ahead electricity market, we determine the optimal charging and discharging schedules under varying objectives: maximizing net revenues, profits considering capacity degradation, and profits considering both capacity degradation and internal resistance increase due to degradation. The results demonstrate the viability of our approach and underscore the significance of integrating degradation costs into the market strategy for battery operators, alongside its effects on the battery’s dynamic behaviour. Our methodology extends previous work by offering a more comprehensive model that empirically captures the intricacies of battery degradation, including a fine and adaptive time domain representation, focusing on the day-ahead market, and utilising accurate direct methods for optimal control. The paper concludes with insights into the potential of optimal control applications in energy markets and suggestions for future research avenues.

Despite being stored at 113 K and atmospheric pressure, LNG cold potential is not exploited to reduce green ships’ energy needs. An innovative system based on three Organic Ranking Cycles integrated into the regasification equipment is proposed to produce additional power and recover cooling energy from condensers. A first-law analysis identified ethylene and ethane as suitable working fluids for the first and the second ORC making available freshwater and ice. Propane, ammonia and propylene could be arbitrarily employed in the third ORC for air-conditioning. An environmental analysis that combines exergy efficiency, ecological indices and hazard aspects for marine environment and ship’s passengers, indicated propylene as safer and more environmentally friendly. The exergy analysis confirms more than 20% of the LNG potential can be recovered from every cycle to produce a net clean power of 76 kW, whereas 270 kW can be saved by recovering condensers' cooling power to satisfy some ship needs. Assuming the sailing mode, a limitation of 162 kg in LNG consumptions was determined, avoiding the emission of 1584 kg of CO2 per day. Marine thermal pollution is reduced by 3.5 times by recovering the working fluids' condensation heat for the LNG pre-heating.

Retiring coal power plants can reduce air pollution and health damages. However, the spatial distribution of those impacts remains unclear due to complex power system adjustments and pollution chemistry and transport. Focusing on coal retirements in Pennsylvania (PA), we analyze six counterfactual scenarios for 2019 that differ in retirement targets (e.g., reducing 50% of coal-based installed capacity vs. generation) and priorities (e.g., closing plants with higher cost, closer to Environmental Justice Areas, or with higher CO₂ emissions). Using a power system model of the PJM Interconnection, we find that coal retirements in PA shift power generation across PA and the Rest of PJM region leading to scenario-varying changes in the plant-level release of several air pollutants. Due to air pollution chemistry and transport and socio-demographics, these changes in turn give rise to a reduction of 10 to 182 PM_2.5-attributable deaths in PJM across the six scenarios, with most reductions occurring in PA. Scenarios that reduce more coal power generation yield greater aggregate health benefits due to air quality improvements in PA and adjacent downwind regions. In addition, vulnerable populations—in both PA and Rest of PJM—benefit most in scenarios that prioritize plant closures in PA near Environmental Justice Areas. These results demonstrate the importance of considering cross-regional linkages and socio-demographics in designing equitable retirement strategies.

Off-grid electrification planning increasingly recognizes the importance of productive use of electricity (PUE) to promote community value creation and (financial) project sustainability. To ensure a sustainable and efficient integration in the community and energy system, PUE assets must carefully be evaluated to match both the community needs and the residential electricity demand patterns. We propose a novel methodology interlinking qualitative interviews, statistical analysis, and energy system modelling to optimize decision-making for PUE integration in off-grid energy systems in rural Madagascar by aligning relevant PUE effectively with anticipated residential electricity demand patterns based on socio-economic determinants of the community. We find that a possible contribution of the PUE to reducing the electricity costs depends signifi-cantly on three factors: 1. the residential electricity consumption patterns that are influenced by the socio-economic composition of the community, 2. the degree of flexibility of i) PUE assets and ii) operational preferences of the PUE user, and 3. the capacity of community members to finance and operate PUE assets. Our study demonstrates that significant cost reductions for PUE-integrated off-grid energy systems can be achieved by applying our proposed methodology. When matching PUE and residential consumption patterns, the integration of PUE assets in residential community energy system can reduce the financial risk of operators, provided the PUE enterprise operates reliably and sustainably. We highlight that the consideration of local value chains and co-creation approaches are essential to ensure the energy system is addressing the community’s needs, creates value for the community, enhances the project´s financial sustainability, and is achieving the overall objectives of decentralized energy system planning.

Insulation systems for the floor, roof and external walls play a prominent role in providing a thermal barrier for the building envelope. Design decisions made for the insulation material type and thickness can alleviate potential impacts on the embodied energy and improve the building thermal performance. This design problem is often addressed using a BIM-integrated optimisation approach. However, one major weakness lies in the current studies is that BIM is merely used as the source for design parameters input. This study proposes a BIM-based envelope insulation optimisation design framework using a common software Revit to find the trade-off between the total embodied energy of the insulation system and the thermal performance of the envelope by considering the material type and thickness. In addition, the framework also permits data visualisation in a BIM environment, and subsequent material library mapping together with instantiating the optimal insulation designs. The framework is tested on a case study based in Sydney, Australia. By analysing sample designs from the Pareto front, it is found that slight improvement in the thermal performance (1.3399 to 1.2112 GJ/m2) would cause the embodied energy to increase by more than 50 times.

Volcanic activity essentially consists of the transfer of heat from the Earth’ interior to the surface. The precise signature of this heat transfer relates directly to the processes underway at and within a particular volcano and this can be observed, at a safe distance, remotely, using infrared sensors that are present on Earth-orbiting satellites. For over 50 years, scientists have perfected this art using sensors intended for other purposes, and they are now in a position to determine the particular sort of activity that characterizes different volcanoes. This review will describe the theoretical basis of the discipline and then discuss the sensors available for the task and the history of their use. Challenges and opportunities for future development in the discipline are then discussed.

We have modelled the energy consumption of prototype and real buildings under present and future climatic conditions with the EnergyPlus model to develop a better understanding of the relationship between changing climate conditions and energy demand. We have produced detailed meteorological information with 50 meters of spatial resolution through dynamical downscaling process combining regional, urban and computational fluid dynamics models which include the effects of the buildings on urban wind patterns. The city of Madrid has been chosen for our experiment. The impact on energy demand and their respective economic cost are calculated for year 2100 versus 2011 based on two IPCC climate scenarios, RCP 4.5 (stabilization of emissions) and RCP 8.5 (not reduction of emissions). Findings show that climate change will have a significant impact on the energy demand for buildings. Space heating demand will be increased by the RCP 4.5 and cooling demand will be increased for the RCP 8.5 in the analysed buildings.

In this paper, the effect of an exterior shading element (Iwan) on energy consumption in four different climatic regions, and for different geographical directions, has been investigated numerically and experimentally. By applying different materials and techniques and creating various elements and spaces, architects make hard climatic conditions more tolerable for residents. Iwan is one of the cooling elements which is used in different forms and dimensions in the Islamic architecture. In the present research, Iwan has been introduced as a climatic element in traditional and contemporary architectures and its role in reducing the energy consumption in buildings has been studied. In this respect, first, the thermal loads of a building without Iwan are computed by means of EnergyPlus software. Then, four different forms of Iwan are added to the above-mentioned structure along the four principal geographical directions, and the effect of Iwan on the reduction of thermal loads is analyzed for four different climates. Finally, the design parameters of Iwan, in terms of depth and form, that can help reduce the thermal loads in different climatic conditions are presented. The results show that the best position for using an Iwan is the south direction and the use of Iwan in temperate & humid, hot & humid, cold & mountainous and hot & dry climates could reduce the energy consumption in buildings by 32%, 26%, 14%, and 29%, respectively.

This paper describes a case study of ventilation as well as measured and perceived indoor air quality (IAQ) in a Finnish comprehensive school with a hybrid ventilation system and reported IAQ problems. An operational error was found when investigating the ventilation system that prevented air from coming into classrooms, except for short periods of high carbon dioxide (CO₂) concentrations. However, results indicated that hybrid ventilation system was able to provide adequate ventilation and sufficient IAQ once properly designed and maintained. After ventilation operation was improved, occupants reported less unpleasant odors and stuffy air. The amount of total volatile organic compounds (TVOC) and some single volatile organic compounds (VOCs) decreased. Indoor mycobiota was observed in settled dust in the classrooms, from which ventilation improvement eliminated the dominant, opportunistic human pathogen species Trichoderma citrinoviride found before improvement.

This paper presents a study about the integration of Piezoelectric Energy Harvesting Systems (PE-EHS) in building envelopes for powering Fiber Bragg Grating (FBG) sensors, enabling efficient and low-consumption monitoring with the objective to leverage Structural Health Monitoring (SHM). The research includes preliminary tests conducted in a real environment to validate the PE-EHS when fully integrated into the façade, capturing mechanical vibrations generated mainly by wind loads. Based on these activities, the final configuration of PE-EHS is defined to provide a complete system for façade monitoring. This integrated system includes the Piezoelectric Generator (PEG), Supercapacitor (SC), Power Conditioner Circuit (PCC), Fibre Optic Sensing (FOS) Interrogator, and the IoT Gateway trans-mitting measurement data within an Internet of Things (IoT) monitoring platform. This configuration is tailored to address the challenges related to the structural integrity of building envelopes. Results demonstrate a potential for a stand-alone solution in the façade sector, but, raising issues for certain limitations, requiring further investigation. In particular, the study emphasizes constraints related to the energy production of PE-EHS for façade integration. It highlights the necessity to carefully consider these limitations within the broader context of their applicability, providing insights for the informed deployment of Piezoelectric Energy Harvesting technology in building envelope monitoring.

The role of natural factors mainly solar eleven-year cycle variability, and volcanic eruptions on two major modes of climate variability the North Atlantic Oscillation (NAO) and El Niño Southern Oscillation (ENSO) are studied for around last 150 years period. The NAO is the primary factor to regulate Central England Temperature (CET) during winter throughout the period, though NAO is impacted differently by other factors in various time periods. Solar variability indicates a strong positive influence on NAO during 1978-1997, though suggests opposite in earlier period. Solar NAO lag relationship is also shown sensitive to the chosen times of reference and thus points towards the previously proposed mechanism/ relationship related to the sun and NAO. The ENSO is influenced strongly by solar variability and volcanic eruptions in certain periods. This study observes a strong negative association between the sun and ENSO before the 1950s, which is even opposite during the second half of 20th century. The period 1978-1997, when two strong eruptions coincided with active years of strong solar cycles, the ENSO, and volcano suggested a stronger association, and we discussed the important role played by ENSO. That period showed warming in central tropical Pacific while cooling in the North Atlantic with reference to the later period (1999-2017) and also from chosen earlier period. Here we show that the mean atmospheric state is important for understanding the connection between solar variability, the NAO and ENSO and associated mechanism. It presents a critical analysis to improve knowledge about major modes of variability and their role in climate. We also discussed the importance of detecting the robust signal of natural variability, mainly the sun.

A flow chart is presented depicting coupling in ocean-atmosphere system, initiated by solar decadal variability that involves El Niño Southern Oscillation (ENSO). Possible mechanisms for Canonic ENSO, Modoki ENSO and Canonic-Modoki ENSO are proposed considering their relevance to the decadal variation of Hadley, Walker circulation and mid-latitude jets. It also discusses subsequent teleconnections by ENSO on Indian Summer Monsoon (ISM) with a special emphasis on later two decades of the last century. Possible mechanisms relating to a disruption of the usual ENSO-ISM teleconnection for those decades are emphasised; the role of volcanos and the change in the sun- NAO (North Atlantic Oscillation) connection were attended. The regional Hadley circulation, via the NAO in the northern hemisphere and Indian Ocean Dipole in the southern hemisphere, during that period, may have a role in the change in ISM behaviour- which though captured in observation but missed by models. The representation of flow chart helps to improve understanding of various types of ENSO in both temporal as well as spatial scale. The overall study subsequently can benefit the modelling community by not only improved the representation of ENSO in models but also better representation of ISM teleconnection via regional Hadley cell.

The microstructural evolution, thermodynamics and kinetics of Mo-21%Tm₂O₃ (mass fraction, %) powder mixtures during ball milling were investigated using X-ray diffraction and transmission electron microscopy. Ball milling induced Tm₂O₃ to be decomposed and then dissolved into Mo crystal. The supersaturated nanocrystalline solid solution of Mo (Tm, O) was obtained after 96 h of ball milling. The elements of Mo, Tm and O were distributed uniformly in the ball-milled particles. Based on the semi-experimental theory of Miedema, a thermodynamic model was developed to calculate the driving force of phase evolution. There was no chemical driving force to form a crystal solid solution of Tm atoms in Mo crystal or an amorphous phase because the Gibbs free energy for both processes was higher than zero. For Mo-21%Tm₂O₃, it was mechanical work, not negative heat of mixing, that provided the driving force to form supersaturated nanocrystalline Mo (Tm, O) solid solution.

(1) Background: A simple approach to map irrigated landcover has been introduced by using measures derived from optical spectral range as an alternative to thermal range. It has been demonstrated that substituting surface temperature (Ts, ‘thermal approach’) with SWIR transformed reflectance (STR, ‘optical approach’) to detect surface moisture is feasible with comparable results. (2) Methods: Using an iterative thresholding procedure to minimize within-class variance, the bilevel segmentation of variables derived from Landsat-8 representing surface moisture and vegetation cover was achieved for the 2020-21 summer for a key irrigation district in Australia. (3) Results: The results of irrigated landcover by optical approach found to be comparable with those by thermal approach. The classification accuracy was assessed using water delivery records at farm level. Though the overall accuracy is high in both cases, the optical approach (97.6%) performed slightly better than the thermal approach (93.9%). (4) Conclusions: The feasibility of using STR to map irrigated landcover has been confirmed by a high-level overall accuracy assessment. This has broader implications in terms of irrigated landcover assessment, as the use of satellite imagery in these applications may not necessarily be limited to microwave or thermal sensors.

Thermal comfort is extremely important in architecture, especially in environments with more people spending longer on studies or intellectual activities. This research describes a case study to investigate university buildings' energy and thermal performance as a part of the ANEEL program. Due to this importance, and the need to save energy in Brazilian public buildings, the ANEEL-the Brazilian Energy Electricity Regulatory Agency, launched 2016 a national program focusing on energy efficiency in public universities around the country. University offices and classrooms require high intellectual effort; thus, environmental comfort is critical for maintaining its users' physical and mental health. This study included a pre-diagnosis of the performance of the envelope, lighting, and air conditioning systems and a survey about the quality of the environments from the users' point of view. The Prescriptive Method of the Brazilian Labeling Program (PBE) for Commercial, Service, and Public Buildings (RTQ-C) assessed the building performance. Statistical analysis was applied to correlate the quality and thermal preference of the users from the PMV/PPD. The results showed a high rate of thermal discomfort in both environments of the studies, even when using air conditioning.

Ninety percent of the existing building stock in Europe was built before 1990. These buildings are in urgent need for a significant improvement of energy-efficiency through renovation. Regrettably, so far only five percent of renovation projects have been able to yield energy-saving at deep renovation level. State-of-the-art renovation solutions are available, but costly and lengthy renovation processes and incomprehensible technical complexities hinder the achievement of a wide impact at a European scale. This paper presents research on Plug-and-Play (PnP) technologies supported by Building Information Modelling (BIM) to provide affordable, interchangeable and quick-installation solutions to overcome the main barriers of building deep renovation.

In higher education, the cultivation of research competency is pivotal for students’ critical thinking development and their subsequent transition into the professional workforce. While statistics plays a fundamental role in supporting the completion of a research project, it is often perceived as challenging, particularly by students in majors outside mathematics or statistics. The connection between students’ statistical proficiency and their research competency remains unexplored despite its significance. To address this gap, we utilized the supervised machine learning approach to predict students’ research competency, as represented by their performance in a research methods class, with predictors of students’ proficiency in statistical topics. Predictors relating to students’ learning behavior in a statistics course such as assignment completion and academic dishonesty are also included as auxiliary variables. Results indicate that the three primary categories of statistical skills—namely, understanding of statistical concepts, proficiency in selecting appropriate statistical methods, and statistics interpretation skills— can be used to predict students’ research competency, as demonstrated by their final course scores and letter grades. This study advocates for strategic emphasis on the identified influential topics to enhance efficiency in developing students’ research competency. Findings could inform instructors in adopting a strategic approach to teaching the statistical component of research for enhanced efficiency.

Low energy consumption is a significant contribution of new and retrofitted buildings that place an emphasis on energy efficiency. Although the mandatory requirements of the U-factor and R-value are described in the Vietnamese National Technical Regulation on the energy efficiency of buildings—QCVN09:2017/BXD, these values are not widely publicized, leading to designers facing difficulties when choosing suitable materials at the design stage. This study focuses on the method used to declare the heat transfer values of building materials based on the energy labeling process in order to create an energy labeling program for building materials. To accomplish this objective, criteria and labeling procedures for windows, doors, walls, and building roofs have been developed. In addition, a case study of insulation product labeling was used to evaluate the applicability of the developed labeling program in the implementation phase.

This paper reports modelling outcomes for improvements to building energy performance in Indonesia. Long-term climate effects due to building energy demands including carbon emissions are also considered. The global change assessment model (GCAM) was used to generate the related end-user building energy data, including socioeconomics for urban areas of Indonesia. As a comprehensive study, the total life cycle of carbon in the building sector and the concept of zero-carbon buildings, including energy efficiency, zero-emissions electricity and fuel switching options were considered. Building shell conductance (u-value) of building envelope, floor area ratio (FAR), air conditioner (AC) efficiency, electrical appliances (APLs) efficiency, rooftop photovoltaic (PV) performance and ground source heat pump (GSHP) systems were considered as parameters to mitigate carbon emissions under the operational energy category in GCAM. Carbon mitigation associated with the cement production process was considered in the raw material category. Urban population and labour productivity in Indonesia were used as base inputs with projected growth rates to 2050 determined from available literature. Low growth rate ‘LowRate’ and high growth rate ‘HighRate’ were considered as variable inputs for u-value, FAR, AC efficiency, APLs efficiency, and PV capacity factor to model emissions mitigation. The energy consumption of the GSHP was compared to the conventional reverse cycle ACs to identify the potential of the GSHP as a fuel-switching option. Only base input data were used for cement production process parameters without applying any variable inputs. GCAM base scenarios based on input data only (without modifying variable data) for the residential building sector in Indonesia were considered the benchmark for this study. Total potential carbon emissions mitigation was found to be 432 Mt CO2-e for the residential building sector in Indonesia over 2020-2050. It was found that an average of 24% carbon emissions mitigation could be achieved by 2020-30 and 76% in 2031-2050.

Due to urban warming, energy demand for cooling buildings is rising. The current study used CitySim to estimate the cooling energy requirements for 40 buildings in Downtown, Dubai using high-resolution climate data from weather research and forecasting (WRF) coupled with single layer urban canopy model (SLUCM). Simulating the four mitigation scenarios allowed for the examination of the reduction in cooling load caused by the addition of greenery at a rate ranging from 25% to 100%. The insulated building's cooling demand reduced by a maximum of 13.89% under 100% GI (M4). Scenario M4 resulted in a reduction of 4.6 kWh/m2 and 3.1 kWh/m2 for the non-insulated and insulated low-rise residential buildings, respectively, while the high-rise buildings saw a reduction of 3.09-4.91 kWh/m2 for the non-insulated and 2.07-3.09 kWh/m2 for insulated buildings. This study offered a potential remedy to deal with the problem of urban heating in subtropical environments.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

The article delves into the crucial realm of compressing hydrogen in its gaseous state, a pivotal process for enhancing its viability in both civil and industrial sectors. The study initiates by providing a concise overview and comparison of diverse hydrogen storage methodologies, laying the groundwork with an in-depth analysis of hydrogen's thermophysical properties. It scrutinizes plausible configurations for hydrogen compression, aiming to strike a delicate balance between energy consumption, predominantly derived from the fuel itself, and the requisite number of compression stages. Notably, to render hydrogen storage competitive in terms of volume, pressures of at least 350 bar are deemed essential, albeit at an energy cost amounting to approximately 10% of the fuel's calorific value. Multi-stage compression emerges as a crucial strategy, not solely for energy efficiency, but also to curtail temperature rise, with an upper limit set at 200°C. This nuanced approach is underlined by the exploration of compression levels commonly cited in the literature, particularly 350 bar and 700 bar. Ultimately, the study advocates for a three-stage compression system as a pragmatic compromise, capable of achieving high-pressure solutions while keeping compression work below 10 MJ/kg, a threshold indicative of sustainable energy utilization.

This paper analyzes and compares models for predicting average magnet losses in interior permanent-magnet motors with fractional-slot concentrated windings due to harmonics in the armature reaction (assuming sinusoidal phase currents). Particularly, loss models adopting different formulations and solutions to the Helmholtz equation to solve for the eddy currents are compared to a simpler model relying on an assumed eddy-current distribution. Boundaries in terms of magnet dimensions and angular frequency are identified (numerically and using an identified approximate analytical expression) to aid the machine designer whether the more simple loss model is applicable or not. The assumption of a uniform flux-density variation (used in the loss models) is also investigated for the case of V-shaped and straight interior permanent magnets. Finally, predicted volumetric loss densities are exemplified for combinations of slot and pole numbers common in automotive applications.

This paper focus on the modeling and time-domain analyzing method of piecewise-smooth fractional-order circuit systems. Firstly, an analytical framework is constructed based on a generalized piecewise-smooth two-port impedance network model, which takes the topological characteristics of Dickson type switched-capacitor converters (SCCs) as examples, and considers the fractional-order characteristics of class-2 X7R ceramic capacitors, which are widely used in SCCs. Secondly, the time-domain analyzing method for such a piecewise-smooth fractional-order circuit system is developed, numerical solutions are obtained, and the influence of the fractional-order capacitor on the power conversion efficiency of the system are revealed. Finally, in order to validate the analysis, both numerical simulation and experiments are provided in the work, the results of which confirm that, the proposed fractional-order analytical framework can capture the power loss mechanism of piecewise-smooth fractional-order circuit systems more effectively than the traditional integer-order based approach, thus benefiting the design of circuit systems.

This work (in two parts) will review the recently developed predictive modeling methodology called “4th-BERRU-PM” and its applicability to energy systems as exemplified by an illustrative application to the Polyethylene-Reflected Plutonium (acronym: PERP) OECD/NEA reactor physics benchmark. The acronym 4th-BERRU-PM designates the “Fourth-Order Best-Estimate Results with Reduced Uncertainties Predictive Modeling” methodology, which yields best-estimate results with reduced uncertainties for the first fourth-order moments (mean values, covariance, skewness, and kurtosis) of the optimally predicted posterior distribution of model results and calibrated model parameters. The 4th-BERRU-PM uses the Maximum Entropy (MaxEnt) principle to incorporate fourth-order experimental and computational information, including fourth (and higher) order sensitivities of computed model responses to model parameters, thus incorporating, as particular cases, the results previously predicted by the second-order predictive modeling methodology 2nd-BERRU-PM, and vastly generalizing the results produced by extant data assimilation and data adjustment procedures. The 4th-BERRU-PM methodology encompasses the scopes of high-order sensitivity analysis (SA), uncertainty quantification (UQ), data assimilation (DA) and model calibration (MC). The application of the 4th-BERRU-PM methodology to energy systems is illustrated by means of the above-mentioned OECD/NEA reactor physics benchmark, which is modeled using the neutron transport Boltzmann equation involving 21976 imprecisely known parameters, the solution of which is representative of “large-scale computations.” The model result (“response”) of interest is the leakage of neutrons through the outer surface of this spherical benchmark, which can be computed numerically and measured experimentally. Part 1 of this work illustrates the impact of high-order sensitivities, in conjunction with parameter standard deviations of various magnitudes, on the determination of the expected value and variance of the computed response in terms of the first four moments of the distribution of the uncertain model parameters. Part 2 of this work will illustrate the capabilities of the 4th-BERRU-PM methodology for combining computational and experimental information, up to and including forth-order sensitivities and distributional moments, for producing best-estimate values for the predicted responses and model parameters while reducing their accompanying uncertainties.

Due to environmental concerns, natural refrigerants and their use in refrigeration and air conditioning systems are receiving more attention from manufacturers, end users and the scientific community. The study of heat transfer and pressure drop is essential for accurate design and more energy efficient cycles using natural refrigerants. The aim of this work is to provide an overview of the latest outcomes related to heat transfer and pressure drop correlations for ammonia, propane, isobutane and propylene and to investigate the current state of the art in terms of operating conditions. Available data on the existing correlations of heat transfer coefficient and pressure drop for natural refrigerants have been collected through a systematic search. Whenever possible, validity intervals are given for each correlation and the error is quantified. It is the intention of the authors that this could be a valuable support for researchers and an aid to design, with particular reference to heat pumps. A procedure based on the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) statement was adopted, and the Scopus database was used to query the relevant literature. A total of 135 publications qualified for inclusion in the survey; 34 articles report experimental investigations for not usual geometric conditions. Of the 101 selected papers related to usual geometric conditions, N = 50 deal only with HTC, N = 16 deal only with pressure drop and the remainder (N = 35) analyse both HTC and pressure drop. Among the 85 HTC papers (N = 53) deal with the evaporating condition, N = 30 with condensation and only N = 2 with the heat transfer correlations under both conditions. Most of the 101 articles concern propane and isobutane. The high temperatures are less widely investigated.

Microwave technology has a potential application in the extraction of zinc from sulphide ores, knowledge of the dielectric properties of these ores plays a major role in the microwave design and simulation for any process. The dielectric properties of zinc sulfide concentrate for two different apparent densities—1.54 and 1.63 g/cm³—have been measured by using the resonance cavity perturbation technique at 915 and 2450 MHz during the roasting process for the temperature ranging from room temperature to 850 °C. The variations of dielectric constant, the dielectric loss factor, the dielectric loss tangent and the penetration depth with the temperature, frequency and apparent density have been investigated numerically. The results indicate that the dielectric constant increases as the temperature increases and temperature has a pivotal effect on the dielectric constant, while the dielectric loss factor has a complicated change and all of the temperature, frequency and apparent density have a significant impact to dielectric loss factor. Zinc sulfide concentrate is high loss material from 450 to 800 °C on the basis of theoretical analyses of dielectric loss tangent and penetration depth, its ability of absorbing microwave energy would be enhanced by increasing the apparent density as well. The experimental results also have proved that zinc sulfide concentrate is easy to be heated by microwave energy from 450 to 800 °C. In addition, the experimental date of dielectric constant and loss factor can be fitted perfectly by Boltzmann model and Gauss model, respectively.

In many developing countries, plastic waste management is left to citizens. This usually results in hazardous landfilling or open-air burning, leading to emissions that are harmful to human health and the environment. An easy, profitable, and clean method of processing and transforming the waste into value is required. In this context, this study provides an open-source methodology to transform low-density polyethylene drinking water sachets, into pavement blocks by using a streamlined do-it-yourself approach that requires only modest capital. Two different materials, sand, and ashes are evaluated as additives in plastic composites and the mechanical strength of the resulting blocks are tested for different proportion mix of plastic, sand, and ash. The best composite had an elastic modulus of 169MPa, a compressive strength of 29MPa, and a water absorptivity of 2.2%. The composite pavers can be sold at 100% profit while employing workers at 1.5X the minimum wage. In the West African region, this technology has the potential to produce 19 million pavement tiles from 28,000 tons of plastic water sachets annually in Ghana, Nigeria, and Liberia. This can contribute to waste management in the region while generating a gross revenue of 2.85 billion XOF (4.33 million USD).

Universitas Gadjah Mada (UGM) is implementing the concept of green campus by various means including through elements in its sustainable campus development plan. With regards to several factors related to Energy and Climate Change indicators set by UI GreenMetric, this research examined the existing condition of the area of UGM which belongs to academic zone in order to construct a proposal based on a building mass reconfiguration. This proposal was aimed to improve the implementation of energy-specific green campus concept within the Forestry cluster area as a sample case study. This selection was based on the average value of the Building Coverage Ratio (BCR) values in all of the clusters; thus, the scenario was relevant for generalization and could be replicated in other clusters in the university. The study was done in three stages of simulation, and was based on a series of digital simulation of sunlight hour and solar radiation run in Grasshopper using Lady Bug environmental analysis plug-in for a period of five summer months during the building office hours. Following the reconfiguration, results had shown a similar downtrend between the amount of sunlight hour and solar radiation in the area (up to 49% and 45% respectively on building envelopes, and up to 44% and 42% respectively on landscaping surfaces). This reduction indicated a potential of energy efficiency by applying selective building mass reconfiguration as a passive design strategy that goes hand in hand with the campus’s development policy to optimize the use of BCR for a greener UGM campus through its many undergoing and upcoming redevelopment projects.

The global agricultural sector is increasingly pressured to adopt sustainable practices and reduce its environmental impact. In this context, greenhouses play a crucial role in enabling year-round crop production, ensuring food security, and minimizing reliance on traditional open-field farming. However, the energy consumption associated with greenhouse operations poses a significant challenge to achieving sustainability goals. As a result, there is a growing emphasis on transitioning greenhouses towards near-zero energy consumption. Near-zero energy consumption in greenhouses refers to the ambitious objective of minimizing energy usage to the greatest extent possible while maintaining optimal growing conditions for crops. This goal encompasses reducing energy consumption for heating, cooling, lighting, and other operational needs, as well as exploring renewable energy sources to power greenhouse operations. This review article offers a comprehensive overview of greenhouse energy consumption, with the main goal of analyzing the present situation, identifying key challenges, exploring potential opportunities, and proposing future perspectives for decreasing energy usage in greenhouse environments. As the focus on sustainable agricultural practices grows, the need to reduce energy consumption in greenhouses becomes increasingly important. The review critically examines current technological models and strategies applied in smart greenhouse applications, as well as the monitoring of microclimatic conditions inside the greenhouse, encompassing factors such as temperature, humidity, CO2 levels, soil quality, and crop cultivation. Moreover, it aims to present existing literature that investigates the advancement of greenhouses toward achieving significant reductions in energy consumption.

In the face of escalating climate concerns and the push for sustainable development, the global shift towards renewable and decentralized energy systems presents new challenges and opportunities. This study investigates integrating decentralized energy production, particularly photovoltaic (PV) systems, into national energy planning, aiming to optimize energy strategies that balance local production and consumption with national objectives. By analyzing the Swiss energy model, the research employs the EnergyScope and REHO models to assess the strategic implications of decentralized versus centralized energy systems. Results show that a decentralized approach can significantly reduce PV installation needs to 35 GW, about 23% of potential capacity, and decrease annual system costs by 10% to CHF 1230 per capita. This strategy emphasizes local consumption, minimizes grid reinforcement demands, and leverages economic advantages while addressing overproduction challenges through effective energy storage and grid management. Conclusions underline the strategic value of combining centralized and decentralized methods for resilient and sustainable energy planning. The study contributes to the discourse on energy policy and infrastructure planning, advocating for a hybrid model that accommodates both local conditions and broader energy objectives, urging further research into climate impacts and technology integration for a comprehensive energy future.

In the drive towards environmental restoration and sustainable energy solutions, effective utilization and management of agricultural crop residues are vital to mitigate greenhouse gas (GHG) emissions and waste accumulation. Converting biogenic wastes into biofuels and bioproducts has the potential to tackle the energy crisis and contribute to environmental remediation. In this investigation, teff husk, primarily generated in Ethiopia during teff production within the agro-industrial sector, is used as the feedstock for the slow pyrolysis process. In Ethiopia, it is estimated that over 1.75 million tons of teff husk are generated annually, with a significant portion being incinerated in the fields, resulting in substantial environmental pollution. This study focuses on assessing teff husk as a potential material for slow pyrolysis, a crucial stage in biochar production, to tap into its biochar-producing potential. To determine the composition of the biomass, the teff-husk was initially analyzed by thermogravimetry. The significant presence of fixed carbon indicates that teff husk is a viable candidate for pyrolytic conversion into biochar particles. The process of slow pyrolysis took place at three varied temperatures—specifically, at 400, 450, and 500 °C. Process parameters of slow pyrolysis such as reaction time, temperature, and heating rate were enhanced to obtain maximum biochar yields. The highest biochar yield of 43.4 wt% was recorded at optimized reaction time, temperature, and heating rate of 120 min, 400 °C, and 4.2 °C/min, respectively. Furthermore, biochar's physicochemical, SEM-EDX, FTIR, and TGA characterization were performed. The thermal stability and carbon content of biochar were found to rise at higher temperatures. Unlike fuel recovery, the results suggest that teff-husk can be used as a feedstock for biochar production.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

Implementing net-zero building design is a crucial step towards decarbonizing the built environment during the entire lifecycle of a building, encompassing both embodied and operational carbon. This paper presents a novel computational approach to design Life Cycle Zero-Carbon Building (LC-ZCB), utilizing parametric integrated modeling through the versatile Grasshopper platform and its plug-ins. The Department of Energy’s prototype residential building at New York Institute of Technology, optimized to fulfill the LC-ZCB target, serves as the base building for this comprehensive study. Four main influencing design parameters, namely geometry, construction technology, thermal resistance of the envelope, and on-site renewable energy production, are defined and three-hundred design combinations are evaluated through the assessment of the operational carbon (OC) and embodied carbon (EC). By incorporating bio-based materials in the design options, the influence of biogenic carbon on the whole carbon footprint of the building case study is addressed by utilizing the GWPbio dynamic method, which assumes 100-year time horizon and incorporates dynamic characterization factors based on time of pulse emissions and two variables: rotation of the biomass and storage period of carbon in products. Finally, to account for potential climate changes, future climate data and 2099 weather conditions are considered during the scenarios assessment. The results demonstrate the potential for achieving LC-ZCB when fast growing biobased materials are largely used as construction materials, fostering a more environmentally responsible future for the construction industry.

The development of accurate dynamic battery pack models for electric vehicles (EVs) is critical for the ongoing electrification of the global automotive vehicle fleet, since these serve as a key element in the energy performance of an EV powertrain system. The Equivalent Circuit Model (ECM) technique at the cell level is commonly employed for this purpose, combining accuracy and efficiency in the representation of battery operation within the broader powertrain system. In this study, a second-order ECM model of a battery cell is being developed using Modelica, an equation-based modeling language. Parameter lookup tables at multiple levels of state of charge (SoC), extracted from Li-ion battery cells with 4 different commonly used cathode materials, have been utilized. This approach allows for a representation of the battery systems that are used in a wide range of commercial EV applications. To verify the model, an integrated EV model is developed and simulation results of the FTP75 driving cycle have been compared against an equivalent application in MATLAB Simulink. The findings demonstrate a close match between the results obtained from both software across different system points. Specifically, the maximum deviation of SoC is limited to 0.08% and the maximum value of relative voltage deviation is 1.4%. The verified model enables the exploration of multiple possible architecture configurations of EV powertrains with Modelica.

In this study, the causal-effect between carbon dioxide emissions and forestry production and trade was investigated in Ghana by employing a data spanning from 1961 to 2014 by using the VECM and ARDL model. Evidence of the long-run equilibrium relationship in the VECM shows that, a 1% increase in veneer sheet production reduces carbon dioxide emissions by 1.47% in the long-run. There was evidence of a bidirectional causality between carbon dioxide emissions and veneer sheet production, carbon dioxide emissions and wood charcoal production, and a unidirectional causality running from carbon dioxide emissions to wood fuel production and plywood production to carbon dioxide emissions. Evidence from the long-run equilibrium relationship in the ARDL model shows that; a 1% increase in plywood production will increase carbon dioxide emissions by 0.17% in the long-run, a 1% increase in sawnwood production will increase carbon dioxide emissions by 0.17% in the long-run, a 1% increase in wood charcoal production will increase carbon dioxide emissions by 0.36% in the long-run and a 1% increase in wood fuel production will increase carbon dioxide emissions by 0.37% in the long-run.

In this study, an attempt was made to investigate the Kenya case of multivariate causality of carbon dioxide emissions by employing a time series data spanning from 1961-2011 using the ARDL method of cointegration analysis. The long-run elasticities show that, a 1% increase in financial development increases carbon dioxide emissions by 0.28%, a 1% increase in GDP per capita increases carbon dioxide emissions by 1.32% and a 1% increase in urbanization decreases carbon dioxide emissions by 1.14%. There was a unidirectional causality running from financial development, food production index, GDP per capita, industrialization and urbanization to carbon dioxide emissions. The innovation accounting shows that 20% of future shocks in carbon dioxide emissions are due to fluctuations in financial development, 9% of future shocks in financial development are due to fluctuations urbanization and 22% of future shocks in food production index are due to fluctuations in carbon dioxide emissions.

This study presents the synthesis and electrochemical evaluation of nitrogen-doped vanadium oxide (N-V2O3/C) as a cathode material for aqueous zinc-ion batteries (AZIBs), using a hydrothermal method. Compared to undoped V2O3/C, N-V2O3/C exhibits enhanced electrical conductivity, capacity, and electrochemical kinetics, attributed to the incorporation of pyridinic and pyrrolic nitrogen. Initial charge-discharge cycles indicate phase transitions to amorphous vanadium oxides, enhancing conductivity. N-V2O3/C shows a high specific capacity of 168.4 mAh g−1 at 10 A g−1 and remarkable reversibility, highlighted by the transient existence of intermediate species during cycling. Optimal electrochemical performance is achieved with a vanadium to nitrogen molar ratio of 2:3, indicating the significant impact of nitrogen doping concentration on the material’s efficiency. This work underscores the potential of N-V2O3/C as a superior cathode material for AZIBs.

Using density functional theory (DFT), the density of states of NH4V3O8 (NVO) was analyzed pre and post-oxygen defects (Od) formation. The findings revealed a reduced bandgap in NVO after Od introduction, emphasizing the role of Od in enhancing conductivity of the material, thus improving its electrochemical attributes. Through the water bath method, both NVO and its oxygen-deficient counterpart, (NH4)2V10O25⸱8H2O (NVOd), were synthesized as potential cathode materials for aqueous zinc-ion batteries (AZIBs). Experimental outcomes resonated with DFT predictions, highlighting the beneficial role of oxygen defects in boosting electrical conductivity. Notably, the refined material displayed a remarkable capacity of 479.3 mAh g-1 at 0.1 A g-1, underscoring its promise for advanced energy storage solutions.

The interaction between the grid network and the offshore wind power plant (WPP) network can lead to the amplification of certain harmonics and potentially resonant conditions. Offshore WPP should limit the increment of harmonic voltage distortion at the point of connection to the grid network as well as within their internal network. The harmonic distortion should be limited within the planning level limits using harmonic compensation, which is usually achieved by using static filters. In this paper an active damping compensation strategy with a STATCOM using emulation of resistance at the harmonic frequencies of concern is analysed. Such a compensation is effective for the local bus, though the performance is not guaranteed at the remote bus. This paper investigates the challenges associated with remote harmonic compensation in the offshore WPP, which is connected to the onshore grid through long high-voltage cables and transformers. First, the harmonic distortion and the compensating effects of the filter are theoretically assessed. Afterwards, they are demonstrated using harmonic propagation studies and time domain simulations in PSCAD.

We present a comprehensive database of near-shore wind observations that were carried out during the experimental campaign of the RUNE project. RUNE aims at reducing the uncertainty of the near-shore wind resource estimates from model outputs by using lidar, ocean, and satellite observations. Here we concentrate in describing the lidar measurements. The campaign was conducted from November 2015 to February 2016 at the west coast of Denmark and comprises measurements from eight lidars, an ocean buoy and three types of satellites. The wind speed was estimated based on measurements from a scanning lidar performing PPIs, two scanning lidars performing dual synchronized scans, and five vertical profiling lidars, of which one was operating offshore on a floating platform. The availability of measurements is highest for the profiling lidars, followed by the lidar performing PPIs, those peforming the dual setup, and the lidar buoy. Analysis of the lidar measurements reveals good agreement between the estimated 10-m wind speeds, although the instruments used different scanning strategies and measured different volumes in the atmosphere. The campaign is characterized by strong westerlies with occasional storms.

The use of energy resources is essential to the survival and development of human civilization. However, inefficient energy use not only has an impact on the economy, but it also has a significant impact on climate change. Studying and analyzing the factors that increase energy consumption is crucial for improving energy management. The aim of this study is to analyze the factors influencing energy savings in a building taken as a study model under two different climatic conditions. Measurements of the building's energy performance were carried out using the EnergyPlus calculation engine, which enabled us to analyze the strengths of building parameters such as the number of lights, the equipment used, occupancy, temperature and the relationships between the factors influenced. EnergyPlus is an important software tool in the field of building energy efficiency, enabling the precise simulation of building energy consumption. Simulation scenarios based on actual consumption data carried out by researchers have made it possible to develop energy management strategies in buildings in order to optimize energy efficiency, and in particular to promote the thermal performance of these buildings. In the present work, EnergyPlus building energy simulation software is used to simulate the energy consumption of the building of the Faculty of Electrical Engineering at the "Gheorghe Asachi" Technical University in Iasi, in order to determine the factors influencing building energy consumption. It has been shown that occupancy and heating and cooling systems are the key factors influencing energy consumption in buildings. The advantage of this study is that it can be used to model the most influential factors in predicting future energy consumption in buildings.

The building sector of most tropical countries still use predominantly primary biomass as the principal fuel. This has adverse effects like CO2 emission and deforestation and is associated with issues like poverty, ill-health, and low standard of living. Therefore, energy policies try to improve on the efficiency of firewood and charcoal end-use technologies, to palliate the negative effects. In this research, the global change assessment model (GCAM) is used, to investigate the impact of efficiency improvement on the energy consumption pattern of the building sector of developing countries. The aim of the study is to provide empirical data that would better inform policymakers on the effects of modernizing these primary fuels. The study developed three scenarios with different levels of efficiency improvements. The results show that efficiency improvement rather increases primary biomass consumption and CO2 emission. However, there is a fall in the consumption of traditional biomass in the second half of the modelling period. The increase in biomass-based fuels consumption was seen to be linked to their affordability. Therefore, policymakers need not only elaborate policies that improve biomass efficiency, but also introduce and motivate other clean cooking fuels like butane, biogas, and electricity.

This study aims to suggest a basis for the selection of technologies for developing high-performance buildings to reduce energy consumptions and greenhouse gas emissions. Energy-saving technologies comprising of 15 cases were categorized into passive, active, and renewable energy systems. EnergyPlus v8.8 was used to analyze the contribution of each technology in reducing the primary energy consumptions and CO₂ emissions in the Korean climate. The primary energy consumptions of the base model were 464.1 and 485.1 kWh/m²a in the Incheon and Jeju, respectively, and the CO₂ emissions were 83.4 and 87.4 kgCO₂/m²a, respectively. Each technology (cases 1–15) provided different energy-saving contributions in the Korean climate depending on their characteristics. The heating, cooling, and other energy-saving contributions of each technology indicate that their saving rates can be used when selecting suitable technologies during the cooling and heating seasons. Case 15 (active chilled beam with dedicated outdoor air system + ground source heat pump) showed the highest energy saving rate. In case 15, the Incheon and Jeju models were reduced by 189.4 (59.2%) and 206.2 kWh/m²a (57.4%) compared to the base case, respectively, and the CO₂ emissions were reduced by up to 32.7 (60.8%) and 35.6 kgCO₂/m²a (59.3%), respectively.

Nacelle-based Doppler wind lidars have shown promising capabilities to assess power performance, detect yaw misalignment or perform feed-forward control. The power curve application requires uncertainty assessment. Traceable measurements and uncertainties of nacelle-based wind lidars can be obtained through a methodology applicable to any type of existing and upcoming nacelle lidar technology. The generic methodology consists in calibrating all the inputs of the wind field reconstruction algorithms of a lidar. These inputs are the line-of-sight velocity and the beam position, provided by the geometry of the scanning trajectory and the lidar inclination. The line-of-sight velocity is calibrated in atmospheric conditions by comparing it to a reference quantity based on classic instrumentation such as cup anemometers and wind vanes. The generic methodology was tested on two commercially developed lidars, one continuous wave and one pulsed systems, and provides consistent calibration results: linear regressions show a difference of ∼ 0.5 % between the lidar-measured and reference line-of-sight velocities. A comprehensive uncertainty procedure propagates the reference uncertainty to the lidar measurements. At a coverage factor of two, the estimated line-of-sight velocity uncertainty ranges from 3.2 % at 3 m s⁻¹ to 1.9 % at 16 m s⁻¹. Most of the line-of-sight velocity uncertainty originates from the reference: the cup anemometer uncertainty accounts for ∼ 90 % of the total uncertainty. The propagation of uncertainties to lidar-reconstructed wind characteristics can use analytical methods in simple cases, which we demonstrate through the example of a two-beam system. The newly developed calibration methodology allows robust evaluation of a nacelle lidar’s performance and uncertainties to be established in order to further be used for various wind turbines’ applications in confidence.

Building energy consumption plays an essential role in urban sustainability. The prediction of the energy demand is also of particular importance for developing smart cities and urban planning. Machine learning has recently contributed to the advancement of methods and technologies to predict demand and consumption for building energy systems. This paper presents a state of the art of machine learning models and evaluates the performance of these models. Through a systematic review and a comprehensive taxonomy, the advances of machine learning are carefully investigated and promising models are introduced.

Quantifying different stocking rates effects in three study areas placed at Mediterranean forest (Cuenca, Spain) was conducted by applying a multiparametric soil quality index, SQI, developed in undisturbed forest soils (> 40 years). The main objective is to advance in the development and application of multiparametric indexes which allow for soil condition assessment. For it, is analyse the effectiveness of a multiparametric soil quality index (SQI) as an indicator livestock impacts on the soil in mediterranean forests. Control areas without stocking rates were compared in forest stands with different age (Thicket forest stand, < 30 years; High polewood forest stand, 30-60 years; Old growth forest stand, > 60 years); with various intensity grazing areas (permanent livestock passage: inactive sheepfold for 2-3 years, and active sheepfold; intermittent livestock passage: bare soil, pine stand, scrubland). The multiparametric soil quality index (SQI) applied sensitive to changes in forest ecosystems depending of different stocking rates. However, for even more preci-sion to assess cattle alteration, multiparameter index recalibrated, creating a new one; Soil Status Index by Livestock (SSIL). Correlation between quality ranges obtained with both indexes in dif-ferent study areas suggest that SSIL can be considered a livestock impact reference indicator in Mediterranean forest soils.

The new unique technology for granulation of metals and nonmetallic melts is presented in the paper. It was created on the newly developed controlled film flow disintegration with rapid cooling of the droplets and solidified granules in amorphous state. Three new phenomena discovered by us created the base for 3 different methods for granulation of metals and nonmetallic melts in a wide range of granules’ sizes. Electromagnetic resonance method allows producing granules of metals in the range of 1 mm and over. The soliton-like vibrational regime is available for production of any granulation material in the range 0.1-1 mm. Moreover, the shockwave regime is applicable for producing particles from 10 micrometers by size. All methods produce particles of the stated size with a narrow distribution by size: deviation from the average size no more than 50%. The other known methods do not produce granules with such high cooling rate, which can realize the amorphous state and cannot regulate size of particles in such bright but narrow range from 10 micrometers to 1-2 mm.

In this work, satellite data from the Clouds and Earth’s Radiant Energy System (CERES) and Moderate Resolution Imaging Spectroradiometer (MODIS) instruments is analyzed to determine how the global absorbed sunlight and global entropy generation rate have changed during the time period from 2002 to 2023. The data is used to test hypotheses derived from the Maximum Power Principle (MPP) and Maximum Entropy Production Principle (MEP) about the evolution of earth’s surface and atmosphere. The results indicate that the amount of absorbed sunlight has increased over the last 20 years but rising surface temperatures have caused the entropy generation rate to remain approximately constant despite that decrease in albedo. The results are simpler to explain using the MPP but do not completely rule out the MEP. Given the acceptance of the MPP or MEP, some extensions and nuances are discussed.

Electricity consumption is often the hotspot of life cycle assessment (LCA) of products, industrial activities, or services. The objective of this paper is to provide a consistent, scientific, region-specific electricity-supply-based inventory of electricity generation technology for national and regional power grids. Marginal electricity generation technology is pivotal in assessing impacts related to additional consumption of electricity. China covers a large geographical area with regional supply grids; these are arguably equally or less integrated. Meanwhile, it is also a country with internal imbalances in regional energy supply and demand. Therefore, we suggest an approach to achieve a geographical subdivision of the Chinese electricity grid, corresponding to the interprovincial regional power grids, namely the North, the Northeast, the East, the Central, the Northwest, and the Southwest China Grids, and the China Southern Power Grid. The approach combines information from the Chinese national plans on for capacity changes in both production and distribution grids, and knowledge of resource availability. The results show that nationally, marginal technology is coal-fired electricity generation, which is the same scenario in the North and Northwest China Grid. In the Northeast, East, and Central China Grid, nuclear power gradually replaces coal-fired electricity and becomes the marginal technology. In the Southwest China Grid and the China Southern Power Grid, the marginal electricity is hydropower towards 2030.

Building energy consumption is the main urban energy consumption component, which mainly serves people-centered work and living energy demands. Based on the physical requirements of humans in urban buildings and to determine the comfortable body temperature in each season, this paper establishes a sizing optimization model of building-type integrated energy systems (IES), where the cooling and heating loads required to maintain indoor somatosensory body comfortable temperature are calculated. Depending on the external energy price, internal power balance and other constraints, the model develops an optimal sizing and capacity panning method of energy conversion and storage unit in a building-type IES with PV generation. The operating principle is described as follows: the PV generation is fully consumed, a gas engine satisfies the electric and thermal base load requirements, while the power system and a heat pump supply the remaining loads. The gas price, peak-valley electricity price gap and heat-topower ratio of gas engines are considered as important factors for the overall techno-economic analysis. The developed method is applied to optimize the economic performance of building-type IES and verified by practical examples. The results show that using the complementary characteristics of different energy conversion units is important to the overall IES cost.

High electricity demand for consumption at current supply level in Indonesia led to the rising cost of electricity bills. This factor is compounded by the fact that many electric generators in Indonesia still use fossil fuels, which contributes to the high basic generation cost. UBL is one of the universities that aim to be a green campus. Our research explores the possibility of installing motion sensor to contribute on the energy efficiency. Although mostly common in developed countries, the use of motion sensor for energy efficiency is still rare, especially in Indonesia. despite rising cost and supply shortages, Indonesian buildings are still of high energy consumption. our experiment shows that simple installation of commercially available motion sensors can contribute to reduce the electricity bill from the increase of energy efficiency. One of the efforts to lower energy demand in consumer side is to use the electricity efficiently, such as turning off lights in a room when it's not in use. This method can be simply done by turning the light switches for office and classrooms, but difficult to do in public spaces such as toilets and corridors. Our experiment shows that simple installation of commercially available motion sensors can contribute to reduce the electricity bill from the increase of energy efficiency. Automatic light switches experimentally installed in sample toilet room prove that electricity consumption from the lamps can contribute to the reduction of total weekly energy that translates into Green House Gas emission reduction.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

Digital twins are gaining in popularity for simulating complex natural and urban environments. In this context, accurate segmentation of objects within 3D urban environments is of crucial importance. The aim of this project is to develop a methodology for extracting buildings from textured 3D meshes. To this end, PicassoNet-II, a semantic segmentation architecture is employed. The methodology also incorporates Markov field-based contextual analysis to assess post-segmentation features. In addition, building instantiation is performed using cluster analysis algorithms. Training this model to fit various datasets requires a large amount of annotated data, both from Quebec City, Canada, and from simulated data. Experimental results show that the use of simulated data improves segmentation accuracy, and the DBScan algorithm proves effective in extracting isolated buildings. This project paves the way for improved applications in 3D urban modeling, offering opportunities in fields ranging from urban planning to resource management. The positive results with simulated data reinforce the impact of this research on improving digital models of our ever-changing urban environments.

Three-dimensional V₂O₅ hollow structures have been prepared through a simple synthesis strategy combining solvothermal treatment and a subsequent thermal annealing. The V₂O₅ materials are composed of microspheres 2–3 μm in diameter and with a distinct hollow interior. The as-synthesized V₂O₅ hollow microspheres, when evaluated as a cathode material for lithium-ion batteries, can deliver a specific capacity as high as 273 mAh·g⁻¹ at 0.2 C. Benefiting from the hollow structures that afford fast electrolyte transport and volume accommodation, the V₂O₅ cathode also exhibits a superior rate capability and excellent cycling stability. The good Li-ion storage performance demonstrates the great potential of this unique V₂O₅ hollow material as a high-performance cathode for lithium-ion batteries.

In this paper, the technical aspects of a multi-lidar instrument, the long-range WindScanner system, will be presented accompanied by an overview of the results from several field campaigns. The long-range WindScanner system consists of three spatially separated coherent Doppler scanning lidars and a remote master computer that coordinates them. The lidars were carefully engineered to perform arbitrary and time controlled scanning trajectories. Their wireless coordination via the master computer allows achieving and maintaining lidars’ synchronization within ten milliseconds. As a whole, the long-range WindScanner system can measure an entire wind field by emitting and directing three laser beams to intersect, and then by moving the beam intersection over the points of interest. The long-range WindScanner system was developed to tackle the need for high-quality observations of wind fields from scales of modern wind turbine and wind farms. It has been in operation since 2013.

Daylighting has been widely adopted in recent years due to its potential to improve the indoor environment in terms of visual comfort and energy-saving. One of the energy-saving techniques for energy-efficient buildings is the integration of louver systems. Louvers are considered more efficient for providing daylight in the interior as compared to other daylighting systems. Here, this paper presents the design of a louver system for conducting energy simulations for lighting and cooling requirements in office spaces. The simulation results indicate that the use of louvers in different opening configurations can lead to energy savings, particularly in the lighting aspect. The louver system in office spaces with a 50% louver opening leads to 27.0% energy savings. Further, the results are presented for different louver openings to calculate the lighting and cooling energy savings. The overall performance of the system is better in terms of providing consistent daylight, which eventually improves energy saving.

We report on the field testing datasets and performance evaluation results obtained from a commercial property-based visually-clear solar window installation site in Perth-Australia. This installation was fitted into a refurbished shopping centre entrance porch, and showcases the potential of glass curtain wall-based solar energy harvesting in built environments. In particular, we focus on photovoltaic (PV) performance characteristics such as the electric power output, specific yield, day-to-day consistency of peak output power, and the amounts of energy generated and stored daily. The dependencies of the generated electric power and stored energy on multiple environmental and geometric parameters are also studied. An overview of the current and future application potential of high-transparency, visually-clear solar window-based curtain wall installations suitable for practical building integration is provided.

The thermal insulation properties of building walls are critical to the overall energy efficiency and comfort of a building. One important factor that can affect these properties is the type of bricks used in construction. Bricks can vary in their geometry and thermal coefficient, which can impact their ability to transfer heat through the wall. The geometry of a brick can affect its thermal properties by altering the amount of air trapped within it and the surface area available for heat transfer. Hollow bricks or those with complex geometries may have lower thermal conductivity than regular solid bricks due to the air pockets trapped within them. Conversely, larger surface areas on the exterior of the brick can increase heat transfer. The thermal coefficient of clay, a common material used in brick production, is another important factor. Clay has a relatively low thermal conductivity, meaning it is a poor conductor of heat. However, the quality of the clay, as well as the firing temperature and duration used in brick production, can impact its thermal coefficient. Higher firing temperatures and longer firing times can result in a more compact and dense clay brick, which can improve its thermal properties. In summary, the thermal insulation properties of building walls can be significantly affected by the type of bricks used in their construction. It is important to consider the geometry and thermal coefficient of the bricks when designing a building to achieve the desired level of thermal insulation. By selecting bricks with appropriate properties, designers can help to improve the energy efficiency and comfort of the building while reducing its environmental impact.

The Predicted Mean Vote (PMV) and the Predicted Percentage of Dissatisfied (PPD) indices are used to assess the indoor environment in terms of human thermal comfort-discomfort. In this study, an experimental combined objective and subjective investigation of thermal comfort perception has been performed in students between 16-18 years old, in a non-air-conditioned school building. The objective approach included instrumentation measurements and data processing according to ISO 7730, whereas, the subjective one was based on answers collection following ISO 10551. The study is mainly devoted to the verification of Fanger’s approach in a building, in free running conditions, under a mild (moderate) climate.The comparison between instrumentation data and questionnaire results presented an underestimation of the mean vote, predicting a cooler sensation than the actual one.

Improper disposal of waste plastic has caused serious ecological and environmental pollution problems. Transforming plastics into high value-added chemicals can not only achieve efficient recycling of waste plastics, but also an effective way to control white pollution. The catalyst selectively breaks the C-C bond of polyolefin plastic under heat treatment and converts it into liquid fuel, thus realizing sustainable recycling of plastics and has a good development prospect. This review provides a detailed overview of the current development of catalytic pyrolysis, catalytic hydrolysis, solvent decomposition and supercritical hydrothermal liquefaction for cracking plastics to make fuel oil. The reaction mechanism, influencing factors and promoting effects of catalysts in various degradation technologies are analyzed and summarized and the latest proposed tandem reaction for degrading plastics is briefly introduced. Finally, some optimization paths of waste plastic pyrolysis to fuel oil technology are proposed: synergies between mixed raw materials, in-depth exploration of catalysts, design and manufacture of reactors that match the pyrolysis technology. All these are important research directions for promoting the industrialization of plastic pyrolysis to fuel oil.

Energy Measurement and Verification (M&V) aims to make inferences about the savings achieved in energy projects, given the data and other information at hand. Traditionally, a frequentist approach has been used to quantify these savings and their associated uncertainties. We demonstrate that the Bayesian paradigm is an intuitive, coherent, and powerful alternative framework within which M&V can be done. Its advantages and limitations are discussed, and two examples from the industry-standard International Performance Measurement and Verification Protocol (IPMVP) are solved using the framework. Bayesian analysis is shown to describe the problem more thoroughly and yield richer information and uncertainty quantification than the standard methods while not sacrificing model simplicity. We also show that Bayesian methods can be more robust to outliers. Bayesian alternatives to standard M&V methods are listed, and examples from literature are cited.

The global demand for energy has been steadily increasing due to population growth, urbanization, and industrialization. Numerous researchers worldwide are striving to create precise forecasting models for predicting energy consumption to manage supply and demand effectively. In this research, a time-series forecasting model based on multivariate multilayered long short-term memory (LSTM) is proposed for forecasting energy consumption and tested using data obtained from commercial buildings in Melbourne, Australia: the Advanced Technologies Center, Advanced Manufacturing and Design Center, and Knox Innovation, Opportunity, and Sustainability Center buildings. This research specifically identifies the best forecasting method for subtropical conditions and evaluates its performance by comparing it with the most used methods at present, including LSTM, bidirectional LSTM, and linear regression. The proposed multivariate multilayered LSTM model was assessed by comparing mean average error (MAE), root-mean-square error (RMSE), and mean absolute percentage error (MAPE) values with and without labeled time. Results indicate that the proposed model exhibits optimal performance with improved precision and accuracy. Specifically, the proposed LSTM model achieved a decrease in MAE by 30%, RMSE by 25%, and MAPE by 20% compared to the LSTM method. Moreover, it outperformed the bidirectional LSTM method with a reduction in MAE by 10%, RMSE by 20%, and MAPE by 18%. Furthermore, the proposed model surpassed linear regression with a decrease in MAE by 2%, RMSE by 7%, and MAPE by 10%. These findings highlight the significant performance increase achieved by the proposed multivariate multilayered LSTM model in energy consumption forecasting.

The building sector accounts for nearly 40% of total primary energy consumption in the U.S. and E.U. and 20% of worldwide delivered energy consumption. Climate projections predict an increase of average annual temperatures between 1.1-5.4°C by 2100. As urbanization is expected to continue increasing at a rapid pace, the energy consumption of buildings is likely to play a pivotal role in the overall energy budget. In this study we used EnergyPlus building energy models to estimate the future energy demands of commercial buildings in Salt Lake County, Utah, USA, using locally-derived climate projections. We found significant variability in the energy demand profiles when simulating the study buildings under different climate scenarios, based on the energy standard the building was designed to meet, with reductions ranging from 10% to 60% in natural gas consumption for heating and increases ranging from 10% to 30% in electricity consumption for cooling. A case study, using projected 2040 building stock, showed a weighted average decrease in heating energy of 25% and an increase of 15% in cooling energy. We also found that building standards between ASHRAE 90.1-2004 and 90.1-2016 play a comparatively smaller role than variation in climate scenarios on the energy demand variability within building types. Our findings underscore the large range of potential future building energy consumption which depend on climatic conditions, as well as building types and standards.

There are many uncertainties and risks in residential electricity consumption during the economic development. Knowledge of the relationship between residential electricity consumption and its key determinant—income—are important to the sustainable development of electric power industry. Using panel data from 30 provinces for the 1995-2012 period, this study investigates how residential electricity consumption changes as incomes increase in China. Previous studies typically used linear or quadratic double-logarithmic models imposing ex ante restrictions on the indistinct relationship between residential electricity consumption and income. Contrary to those models, we employed a reduced piecewise linear model that is self-adaptive and highly flexible and circumvents the problem of “prior restrictions.” Robust tests of different segment specifications and regression methods are performed to ensure the conservatism of the research. The results provide strong evidence that the income elasticity was approximately one, and it remained stable throughout the estimation period. The income threshold at which residential electricity consumption automatically remains stable or slows has not been reached. To ensure the sustainable development of the electric power industry, introducing higher energy efficiency standards for electrical appliances and improving income levels are vital. And government should emphasize electricity conservation in industrial sector rather than in residential sector.

In August 4 2011, United Nations Environmental Program (UNEP) submitted an unprecedented, scientific, groundbreaking Environmental Assessment Report (EAR) of Ogoniland, to the Nigerian government. This was the outcome of a 14–month intensive evaluation of the extent of pollution. It was intended that UNEP’s recommendations would be implemented to restore the devastated environment, on the one hand, and on the other, counteract the numerous environmental health issues that have for decades, plagued Ogoniland. However, five years post EAR, and, despite the seriousness of the situation, no significant resolution has occurred, both on the part of the government, and on the part of Shell Petroleum Development Company (SPDC) or Shell. To date, millions of Niger Delta residents, particularly those living in the oil-bearing communities, continue to suffer severe consequences. Although, the assessment was conducted in Ogoniland, other communities in the Niger Delta are also affected. This article explores prevailing issues, using Ogoniland (a microcosm of the Niger Delta) as an example. A multidisciplinary approach for sustainable mitigation of environmental health risks in the Niger Delta is paramount, and Environmental Management tools offer valuable strategies. Adopting UNEP’s recommendations for addressing environmental health problems requires implementing the Environmental Management/Environmental Management System (EM/EMS) model.

Recycling information can be complex and often confusing which may subsequently reduce the participations in any waste recycling schemes. As a result, this research explored the roles as well as the importance of a holistic approach in designing recycling information using 15 expert-based in-depth interviews. The rationale was to offer a better understanding of what constitutes waste, recycling, and how recycling information should be designed and presented to make recycling more attractive/convenient. Based on the research participants’ perceptions with supports from the existing studies, this research sub-categorised recycling information into three different themes, termed the “WWW” of recycling information components. As a result, these components (or attributes) were extensively described (using findings of semi-structured interviews) to elicit pragmatic guidance for practitioners, policy-makers, and other stakeholders in designing structured communication or information strategies that may simplify and subsequently increase waste-recycling practices. The policy implications of holistic information in enhancing recycling are further discussed.

The scope of this work is to empirically check and prove the practical applicability of the Primordially Hydridic Earth (hereinafter PHE) concept for early exploration of the resources of naturally occurring hydrogen. With the PHE concept postulates interpreted within the local geological, tectonic, petrological and geophysical context, the reconnaissance plan, as well as the field exploration and data acquisition programs, were put together and implemented in the field. The results obtained from the surface (

Shared public buildings have become centers of innovation, integrating advanced technologies to meet evolving societal needs. With a heightened emphasis on occupants’ health and well-being, these buildings serve as hubs for technological convergence, facilitating seamless connectivity and intelligent data analysis and management. Within this context, environmental monitoring emerges as a foundational element, pivotal to all aspects of building management. This article provides findings from the nationally funded RE-START project, which focuses on shared public buildings, with special regard to educational and medical facilities. The project explores enhanced indoor air quality monitoring, focusing in particular on CO2 concentration that is directly correlated with occupancy, as a fundamental element for developing health and safety protocols, energy efficiency strategies, integration of smart building technologies, and data-driven energy management. The intersection of environmental monitoring, energy efficiency, security, and IoT technologies in in indoor spaces are relevant. The outcomes of the study reveal the delicate nature of all the involved components, that need to be carefully developed in an integrated manner.

Buildings’ thermal energy needs are inherently linked to climate conditions. Consequently, it is crucial to evaluate how climate changes affect these energy demands. Despite extensive analysis, a comprehensive assessment involving a diverse range of building types has not been consistently conducted. The primary objective of this research is to perform a coherent evaluation of the influence of climate changes, construction element properties, and the Heating, Ventilation, and Air Conditioning (HVAC) system type of control on the energy requirements of six buildings (residential, services, and commercial). The buildings are considered located in a temperate Mediterranean climate. Our focus is on the year 2070, considering three distinct climatic scenarios: (i) maintaining the current climate without further changes, (ii) moderate climate changes, and (iii) extreme climate changes. The buildings are distributed across three different locations, each characterized by unique climatic conditions. Buildings’ envelope features a traditional External Thermal Insulation Composite System (ETICS) and expanded polystyrene (EPS) serves as thermal insulation material. Two critical design factors are explored: EPS thickness ranging from 0 (no insulation) to 12 cm; and horizontal external fixed shading elements varying lengths from 0 (absence) to 150 cm. Six alternative setpoint ranges are assessed for the HVAC system control: three based on the Predicted Mean Vote (PMV) and three based on indoor air temperature (Tair). Results were obtained with a validated in-home software tool. They show that, even under extreme climate conditions, the application of thermal insulation remains energetically favorable, however its relative importance diminishes as climate severity increases. Then, proper insulation design remains important for energy efficiency. The use of external shading elements for glazing (e.g., overhangs, louvers) proves beneficial in specific cases. As climate changes intensify, the significance of shading elements grows. Thus, strategic placement and design are necessary for good results. The HVAC system’s energy consumption depends on the level of thermal comfort requirements, on the climate characteristics and on the building’s type of use. As climate change severity intensifies, energy demands for cooling increase, while energy needs for heating decrease. However, it’s essential to recognize that the impact of climate changes on HVAC system energy consumption significantly depends on the type of building.

A steel damper column is an energy-dissipating member that is suitable for reinforced concrete (RC) buildings and multistory housing. To assess the seismic performance of buildings with steel damper columns, the peak displacement of the whole building and the energy dissipation demand of the dampers must be evaluated. This article proposes an energy-based prediction procedure for the peak and cumulative response of an RC frame building with steel damper columns. The proposed procedure considers two energy-related seismic intensity parameters, namely the maximum momentary input energy and the total input energy. The peak displacement is predicted considering the energy balance during a half cycle of the structural response, using the maximum momentary input energy. The energy dissipation demand of the dampers is then predicted considering the energy balance during a whole response cycle using the total input energy. The local responses (e.g., peak drift, maximum plastic rotation of beams, maximum shear strain, and energy dissipation demand of dampers) are predicted using pushover analysis. Numerical analysis results for 8- and 16-story RC buildings show that the proposed prediction method achieves satisfactory accuracy.

Solar radiation is closely related to the energy buildings consume for cooling, heating, and lighting purposes. Glazing is the only material of the building envelope that transmits solar radiation and needs to be appropriately designed to reduce energy cㅈonsumption. Currently, smart glass technology is being actively investigated and developed for effective solar radiation control. Among the various types of smart glass, electrochromic glazing is one of the most promising technologies, as it can adjust transmittance on its own, has a wider transmittance range in both the clear and darkened states, and consumes less electricity. Considering the importance of solar radiation adjustment in electrochromic glazing technology, this study attempted to develop an optimal control method for electrochromic glazing. Toward this goal, the solar radiation incident on vertical surfaces and outdoor temperature conditions were controlled in three regions with different climatic characteristics, and the annual cooling, heating, and lighting loads, discomfort glare, and interior illumination were analyzed. This approach enabled the optimal conditions with respect to visual comfort to be determined. Subsequently, the EDPI (Energy and daylight performance index) was used to optimize control conditions for each region, thereby producing integrated evaluations from results with different units and properties. The proposed control method will be utilized to develop a control algorithm and a control system to reduce building energy consumption.

This paper investigated building data from multispectral and single-photon Lidar systems. The multispectral datasets from the individual channels and fused channels were explored. The multispectral and single-photon Lidar data were compared across multiple aspects: the data acquisition geometry, number of echoes, intensity, density, resolution, data defects, noise level, and the absolute and relative accuracy. In addition, we explored the performance of the multispectral and single-photon data for roof plane detection for eight complex/stylish buildings to investigate the suitability of these data for 3D building reconstruction. The building data from the single-photon and multispectral Lidar systems were evaluated with respect to the reference building vector data with an accuracy of better than 5 cm. The advantages and disadvantages of both technologies and their applications in the urban building environment are discussed.

The paper presents an error model of a measurement chain containing link performing discrete wavelet transform algorithm which is most often the last stage of measurement signal processing. The goal is to determine the uncertainty budget of the input quantities of the wavelet transform algorithm. The error model takes into account parts of analog, analog-to-digital and digital processing, describing the properties of subsequent fragments of the chain using their transmittance and processing functions. The proposed model enables the description of both deterministic and non-deterministic properties of signal errors. The proposed model was validated using an example measurement chain created for this purpose.

This research investigates the fatigue behaviour and fracture mechanics of high-performance concrete (HPC), including various compositions such as HPC with basalt aggregates (HPC-B), HPC with gravel (HPC-G), and high-strength coarse mortar (CM) static and cyclic tensile loading within the special priority program SPP 2020. The study aims to integrate fracture mechanics into structural analysis to enhance design guidelines for slender cross-sections and safety-related high-performance structural components. The experimental investigations reveal HPC-B's re-markable superiority, displaying higher compressive strength, modulus of elasticity, and tensile strength compared to HPC-G and CM. A modified disk-shaped compact tension (MDCT) based on ASTM standards, aided by digital image correlation (DIC) unveils fracture behaviour, empha-sizing fracture energy as a crucial parameter. HPC-B exhibits improved crack resistance and notch sensitivity reduction attributed to crushed basalt aggregates and enhanced interfacial transition zone (ITZ). The research scrutinizes factors like material characterization, aggregate morphology, stress levels, and displacement rate on crack formation. High-cycle fatigue tests show HPC-B's superior performance, and post-fatigue analysis reveals enhanced residual fracture toughness attributed to nano-level structural changes, stress redistribution and aggregate-matrix interac-tion. 3D image analysis via Computed Tomography (CT) scans captures mesostructural crack propagation and provide quantitative insights. This study advances the understanding of HPC fatigue behaviour, emphasizing the interplay of aggregate types, morphologies, and their dy-namic response to cyclic loading, offering valuable insights for optimizing design guidelines and fostering innovation in structural engineering.

Here, satellite images from 2006 to 2022 were collected to assess changes in the sandbar topography of the Nakdong River Estuary region, southeast of South Korea. The employed method of satellite image acquisition involves capturing images at the same time each year to facilitate a comparison of topographical changes over time. The shorelines of the islands in the study area, including Jinwoo Island, Shinja Island, and Doyo Sandbar, were analyzed. Shoreline analysis was performed using the digital shoreline analysis system (DSAS) package in ArcGIS. The results indicate that Jinwoo Island is expanding at 6.46 m/year in the direction of Nulcha Island. The western side of Shinja Island is expanding at 4.76 m/year, whereas the eastern side is retreating at a rate of 24.41 m/year. In the case of the Doyo Sandbar, the southern shoreline is retreating at a rate of 14.69 m/year; however, the speed is gradually decreasing. Marked topographical changes are evident in the Nakdong River Estuary, and the interlinked barrier islands undergo deposition and erosion, leading to alterations in the shoreline. These findings serve as foundational data for predicting and addressing environmental and social issues arising in the Nakdong River Estuary region due to climate change.

It is not easy to dynamically analyze thermal bridges that require multidimensional analysis in building energy simulations, which are mostly one-dimensional platforms. To solve this problem, many studies have been conducted and, recently, a study was conducted to model the thermal bridge based on the data by approaching this in a similar way to steady-state analysis, showing high accuracy. This was an early-stage study, which is only applicable when the indoor temperature is constant. By extending this study, a thermal bridge model that can be applied even when the indoor temperature changes over time is proposed and validated. Since the governing equation, the heat diffusion equation, is linear, the key idea is to create and apply two thermal bridge transfer function models by expressing the heat flow entering the room as a linear combination of the transfer function for indoor temperature and the transfer function for outdoor temperature. For the proposed thermal bridge model, the NRMSE of the model itself showed a high accuracy of 99.9%, and in the verification through annual simulation using the model, the NRMSE showed an accuracy of 88.8%.

The hygrothermal transfer is very important for the design of a building envelope for thermal comfort and economic and energy analysis of the building envelope. The applications of various materials in building envelope have been studied extensively. The study presents several models for the hygrothermal transfer for various building walls. Several energy and mass conservation equations with different boundary conditions and input considerations were presented in this paper for concrete, bricks and wooden walls. The effect of hysteresis was ignored in developing most model equations, while few considered flow pattern of fluid through the wall surfaces. Due to the flexibility of Luikov models, it formed the basis for modelling the coupled heat and mass transfer for porous material independent of hygroscopic nature with different boundary conditions defined according to the geometry and orientations. The influence of type of wall, orientation, thickness, the density of the material and climatic variations on the temperature and moisture evolutions within the building materials was more pronounced. Literature, presenting imaging models using imagery software like COMSOL multi-physics, CFD etc. were scarce considering that microscopic imagery is now deployed to measure the heat and moisture evolution in materials. Future models should include shrinkage or expansion influence on the fibrous material like wood due to their behaviour under environmental condition.

Chronic graft-versus-host disease (cGvHD) occurs in 20-50% of recipients following allogeneic haematopoietic stem cell transplantation (allo-HSCT). Corticosteroids (CS) remain the first line treatment but have suboptimal efficacy and carry the risk of long-term side effects. New agents with a better safety profile and higher efficacy, ideally combining immunomodulatory and antifibrotic properties, are urgently needed. From 2016 to 2020, we conducted a phase 2 clinical trial with ATO in chronic GvHD (ClinicalTrials.gov ID NCT02966301 - GMED16-001). This study aimed to evaluate the efficacy and safety of a first-line combination of arsenic trioxide (ATO) and CS in adult patients with cGvHD who require systemic therapy after a first allo-HSCT for a haematological disease. In this prospective, national, multicenter, single-arm, open-label phase II study, conducted in 5 university hospital centers in France, ATO was initiated within 10 days of starting CS at 1 mg/kg/day. Patients received 11 infusions of ATO per 4-week cycle, at a dose of 0.15 mg/kg per infusion. Patients received 1 or 2 cycles of treatment depending on the clinical response and the assessment of the treating physician. The results were published in July 2022 in a paper entitled "High Response Rate and Corticosteroid Sparing with ATO-Based First-Line Therapy in Chronic Graft-versus-Host Disease after Allogeneic Hematopoietic Stem Cell Transplantation". The GMED16-001 study demonstrated convincing efficacy and safety characteristics of the intravenous drug (Trisenox^®/Arscimed^®): the first-line use of ATO in addition to corticosteroids was associated with a high clinical response rate and correlated with rapid corticosteroid (CS) sparing in moderate to severe cGvHD after allo-HSCT. We performed a post-hoc analysis of the data to determine the best schedule for treating cGvHD patients with ATO. Our post-hoc analysis leads us to the conclusion that two cycles of ATO, at 0.15 mg/kg/day, 5 days per week for 4 weeks each, separated by a 4-week therapy-free interval, appears to be the most promising treatment schedule.

The static formation temperature (SFT) is required to determine the thermophysical properties and production parameters in geothermal and oil reservoirs. However, the SFT is not easy to be obtained by both experimental and physical methods. In this paper, a mathematical approach to predicting SFT based on a new model describing the relationship between bottom hole temperature (BHT) and shut-in time was proposed. The unknown coefficients of the model were derived from least squares fit by Particle Swarm Optimization (PSO) algorithm. Besides, the ability to predict SFT based on a few BHT data (such as first 3, 4, or 5 ones of a data set) was evaluated. The accuracy of the proposed method to predict SFT was testified with a deviation percentage less than ±4% and high values of regression coefficient R² (>0.98). The proposed method could be used as a practical tool to predict SFT in both geothermal and oil wells.