This study evaluated the microbiological quality of farm oysters, cultivated in an estuary in northeastern Pará, Brazil, before and after purification process. Water and oyster samples were collected in June, August, October, and December 2019. Oysters underwent purification for up to 36 h in a small-scale adapted debugger. Microbiological analyses were performed in oysters and water depuration collected at different times of purification (0 h pre-treatment, 6 h, 12 h, 2 4h, and 36 h), using the multiple tube technique, to determine the most probable number (MPN) of Escherichia coli, thermotolerant coliforms - TTC, and total coliforms - TC. Bacterial isolation was used to determine the presence of Salmonella spp. Before purification, oysters had E. coli counts above the limit allowed by Brazilian legislation (≤ 230 MPN/100g). High TTC, and TC counts were observed in all the months of the study, and Salmonella spp. was present in August. All water samples were contaminated by TTC beyond the level allowed (> 43 MPN/100mL) in two months. The purification process of 36 h was effective in reducing the load of E. coli, TTC, and TC and eliminating Salmonella spp. in oysters.

Bent trees have been observed during the early years in juvenile plantations (less than 5 years-old) of Tectona grandis in Costa Rica. The relationship between bending and the morphological characteristics of the trees was explored. An evaluation of bent trees was conducted in six juvenile plantations (8, 17, 27, 28, 31, and 54 months old) of Tectona grandis. Site 1 with 8-month-old plantations did not display any relationship with any tree morphological variable (diameter, height, and crown weight of tree), whereas for the sites 2, 3, and 4 with 17-, 27-, and 28-month-old plantations, respectively, all the tree morphological variables were statistically correlated with the bent trees. A multiple regression analysis showed that the most influential variables were height to crown base, crown weight, diameter, and total height of the tree. An evaluation of the bending risk factor (RF) was correlated with the height to crown base, crown weight, and form factor. The modulus of elasticity and chemical compositions of bent trees differed from those of straight trees. The causes of tree bending are complex, involving, among other factors, the morphology of the trees, plantation conditions, and other factors specific to the xylem, such as the specific gravity, modulus of elasticity, and presence of calcium and magnesium in the wood.

The aim of this study was to provide information on the levels of toxic (Cd and Pb) and essential (Cu, Fe and Zn) elements in cow’s milk produced in the State of Pernambuco (Brazil). A total of 142 samples of raw milk were collected, and the concentrations of essential and toxic elements were determined by inductively coupled plasma-optical emission spectrometry. In almost 30 % of the samples analyzed, the Pb content exceeded the maximum level established in the Brazilian legislation (0.05 mg/l). By contrast, in all samples the Cd content was below the maximum allowable level (0.02 mg/L). The essential trace elements Cu, Fe and Zn were generally present at lower concentrations than reported in other studies and can be considered within the deficient range for cow’s milk. Statistical and chemometric procedures were used to evaluate the main factors influencing the metal concentrations (proximity to major roads, presence of effluents, and milking method). The study findings demonstrate that the proximity of the farms to major roads influences the concentrations of Cd, Pb and Cu and that this is the main factor explaining the Pb content of milk. In addition, the presence of effluents influenced the concentrations of Cu, while no relationship between the metal content and the milking method was observed. Thus, in accordance with the study findings, consumption of cow’s milk produced in the region can be considered a risk to public health due to the high concentrations of Pb and the low concentrations of other essential minerals such as Cu, Zn and Fe in some of the milk samples.

One of the operational challenges for the use of bentonite pellets as a sealing material in the abandonment of offshore fields consists in their disposition inside the well. This study aims to analyze the interaction of fluid media, consisting of saline solutions (NaCl, CaCl2 and KCl) and organic compounds (diesel, glycerin and olefin), with bentonite pellets, aiming its application as displacement fluid in offshore oil well abandonment operations. The physical integrity of the bentonite pellets in contact with the fluids was verified through visual inspections and dispersibility tests. Linear swelling tests were also performed to evaluate the potential for swelling of pellets in deionized water after contact with the fluid media. The results indicated that NaCl, CaCl2 and KCl solutions completely compromise the physical integrity of the pellets, while diesel and olefin showed the best responses regarding the structural preservation. Futhermore, the linear swelling tests showed that, even after the contact with diesel and olefin for 1 hour, bentonite pellets have reached a total swelling in water of 78%, after 24 hours. In this way, diesel and olefin proved to be highly promising alternatives to be used as displacement fluids for bentonite pellets in wells to be abandoned in a submarine environment.

In this work, the effect of reaction time and biomass-to-H2O ratio on the structural evolution of hydro-char and kinetic of by hydrothermal processing of corn Stover with hot compressed H2O, have been systematically investigated. The experiments were carried out at 250 °C, heating rate of 2.0 °C/min, biomass-to-H2O ratio of 1:10, and reaction times of 60, 120, and 240 minutes, and at 250 °C, 240 minutes, heating rate of 2.0 °C/min, and biomass-to-H2O water ratio of 1:10, 1:15, and 1:20, using a pilot scale stirred tank reactor of 5 gallon. The characterization of solid phase products performed by thermo-gravimetric analysis, scanning electron microscope, energy dispersive X-ray spectroscopy, X-ray diffraction, and elemental analysis (C, N, H, S). The physical-chemistry properties of solid phase analyzed in terms of dry matter (DM), total organic content (TOC), and ash. The yields of solid and gas phases decrease linearly with decreasing biomass-to-H2O ratio, while that of liquid phases increases linearly. For constant biomass-to-H2O ratio, the yields of solid, liquid, and gaseous reaction products varied between 52.97 and 35.82% (wt.), 44.84 and 54.59% (wt.), and 2.19 and 9.58% (wt.), respectively. The yield of solids decreases exponentially by decreasing the reaction time, while the yields of liquid and gas phases increase exponentially. For constant biomass-to-H2O ratio, TG/DTG curves shows that reaction time of 60 minutes was not enough to carbonize corn Stover. For constant reaction time, TG/DTG curves shows that increasing the H2O-to-biomass ratio worse the carbonization of corn Stover. For constant biomass-to-H2O ratio, the SEM images show the main morphological structure of the corn Stover remains practically unchanged, while for constant reaction time, SEM images show that plant microstructure retains part of its original morphology, demonstrating that a decrease on biomass-to-H2O ratio worse the carbonization of corn Stover. For constant biomass-to-H2O ratio, the EDX analysis shows that the carbon content in hydro-char increases with reaction time, while for constant reaction time, the carbon content decreases with increasing biomass-to-H2O ratio. The kinetic of corn Stover degradation was correlated with a pseudo-first order exponential model, exhibiting a root-mean-square error (r2) of 1.000, demonstrating that degradation kinetics of corn Stover with hot compressed H2O, expressed as hydro-char formation, is well described by an exponential decay kinetics.

In this work, the thermodynamic data basis and EOS modeling necessary to simulate the fractionation of organic liquid products (OLP), a liquid reaction product obtained by thermal catalytic cracking of palm oil at 450ºC, 1.0 atmosphere, with 10% (wt.) Na2CO3 as catalyst, in multistage countercurrent absorber/stripping columns using SC-CO2 as solvent, with Aspen-Hysys was systematically investigated. The chemical composition of OLP was used to predict the physical (), thermo-physical properties (Tb, Tc, Pc, Vc), and acentric factor () of all the compounds present in OLP by applying the group contribution methods of Marrero-Gani, Han-Peng, Marrero-Pardillo, Constantinou-Gani, Joback and Reid, and Vetere. The RK-Aspen (EOS) used as thermodynamic fluid package, applied to correlate the experimental phase equilibrium data of binary systems organic liquid products compounds (OLP)-i/CO2 available in the literature. The group contribution methods selected based on the lowest relative average deviation by computing Tb, Tc, Pc, Vc, and . For n-alkanes, the method of Marrero-Gani selected for the prediction of Tc, Pc and Vc, and that of Han-Peng for . For alkenes, the method of Marrero-Gani selected for the prediction of Tb and Tc, Marrero-Pardillo for Pc and Vc, and Han-Peng for . For unsubstituted cyclic hydrocarbons, the method of Constantinou-Gani selected for the prediction of Tb, Marrero-Gani for Tc, Joback for Pc and Vc, and the undirected method of Vetere for . For substituted cyclic hydrocarbons, the method of Constantinou-Gani selected for the prediction of Tb and Pc, Marrero-Gani for Tc and Vc, and the undirected method of Vetere for . For aromatic hydrocarbon, the method of Joback selected for the prediction of Tb, Constantinou-Gani for Tc and Vc, Marrero-Gani for Pc, and the undirected method of Vetere for . The regressions show that RK-Aspen EOS was able to describe the experimental phase equilibrium data for all the binary pairs undecane-CO2, tetradecane-CO2, pentadecane-CO2, hexadecane-CO2, octadecane-CO2, palmitic acid-CO2, and oleic acid-CO2, showing average absolute deviation (AADx) between 0.8% and 1.25% for the liquid phase and (AADy) between 0.01% to 0.66% for gaseous phase.

This study aimed to detect picobirnavirus (PBV) in the fecal samples of wild and domestic animals from 2014 to 2016 in the Amazon biome. Fecal samples from different animals, including birds (n=41) and mammals (n=217) were used. The PAGE test showed negativity for PBV. However, 32 samples (12.4%, 32/258) showed positive results in RT-PCR analyses. Among the positive sam-ples, pigs and cats, both with 28.12% (9/32), registered the highest frequencies. In phylogenetic analysis, eight sequences from positive samples grouped in the Genogroup 1 of PBV (PBV GI). PBV occurrence was significantly related to cats and pigs, but not other mammals or birds, in-dependently of their geographical origin. Nucleotide analysis demonstrated similarity among the feline group, but the absence of a defined structure between the clades. PBVs are highly wide-spread viruses that can affect the most diverse types of hosts in the Amazon biome, including humans.

Sugarcane plays a crucial role in global sugar and ethanol production. Conventionally, sugar-cane propagation involves planting billets. However, Brazilian researchers have introduced the innovative pre-sprouted seedlings (PSS) method, widely used in the MEIOSI (Simultaneously Occurring Interrotational Method) system. Although MPB has several advantages over the con-ventional method, its sensitivity to water scarcity is a challenge. The study aimed to evaluate the survival and growth of PSS inoculated with Bacillus licheniformis and Bacillus subtilis under differ-ent water regimes. The experiment was conducted in the field in a randomized block in strips (split-block) using a 2×4 factorial scheme consisting of two inoculation conditions (with and without bacteria) and four water regimes (0%, 33%, 66%, and 100% of the ideal irrigation). The bacteria increased the PSS's survival and water use efficiency in the field. In addition, inocula-tion increased root and shoot growth, as well as the nutrient uptake such as N, P, Mn, Zn, and Cu, which resulted in a higher number of stalks per meter and, therefore, a higher multiplica-tion rate in the MEIOSI system. Inoculation proved to be a promising alternative for establishing PSS under water restriction.

Plug and abandonment (P&A) operations demand valuable time and resources with operational procedures and materials to establish the well barrier element. This study proposes the use of a water-based fluid as a liquid well barrier element for temporary abandonment, based on esti-mates of its lifespan and survival probability on downhole conditions acquired through acceler-ated life tests. For that, the water-based formulation was tested and exposed to 95, 110, 140 and 150°C, for time intervals ranging from 1 to 10 days. After temperature exposure, the fluid prop-erties were verified and failure was detected by accounting for any deterioration in rheological parameters and/or a substantial increase in filtrate volume. Statistical analysis of failure data was performed in R software using Weibull Model, and fluid average lifespan and survival probability were estimated for P&A temperatures. The results obtained demonstrates that the degradation of the fluid only was observed for 140 and 150°C and is mostly related to the CMC deterioration. The reliability metrics shows that until 80°C the fluid is a promising alternative for temporary abandonment, with no need of monitoring. For higher downhole temperatures, theses metrics should be considered to define the maximum time of operation and requirements for monitoring management in the operation design.

The Chinese community is one of the main minorities in Colombia, and although China has made advances in public health, it faces a growing burden of cardiovascular diseases. This study focuses on evaluating cardiovascular risk factors in Chinese immigrants in Barranquilla, Colombia, due to the lack of specific data on this population. Methods: A cross-sectional study was conducted with 67 Chinese immigrants over 18 years of age residing in Barranquilla. Sociodemographic, anthropometric, clinical, and biochemical data were collected through structured interviews and medical record reviews. Cardiovascular risk was estimated using the 10-year ASCVD (Atherosclerotic Cardiovascular Disease) formula from the ACC/AHA. Statistical tests were employed to assess significant differences and relationships between variables. Results: The sample included 54% women with an average age of 53 years. 75% were over 45 years old, with the main occupations being trade (43%) and homemaking (40%). 54% had social security. Significant differences were observed in systolic blood pressure and the prevalence of smoking and alcoholism between men and women. Women had higher levels of HDL and lower creatinine, while men had higher levels of hemoglobin and creatinine. Cardiovascular risk was high in 9% of cases, moderate in 39%, and low in 52%. Conclusions: Chinese immigrants in Barranquilla present a significant prevalence of cardiovascular risk factors influenced by their socioeconomic situation and barriers to accessing healthcare. Interventions should focus on improving access to healthcare services and promoting healthy lifestyles for this vulnerable community.

In this work, the cross-linked PMMA-based dental resins scraps were submitted to pyrolysis to recover MMA (Methylmethacrylate). The thermal degradation of cross-linked PMMA-based dental resins scraps was analyzed by TG/DTG to guide the operating conditions in pilot scale. The pyrolysis experiments carried out in a reactor of 143L, at 345, 405, and 420°C, 1.0 atmosphere. The reaction liquid products obtained at 345°C, physicochemical characterized for density, kinematic viscosity, and refractive index. The chemical composition of liquid products obtained at 345°C, 30, 40, 50, 60, 70, 80, and 110 minutes, at 405°C, 50, 70, and 130 minutes, and at 420°C, 40, 50, 80, 100, 110, and 130 minutes determined by GC-MS. The experiments show that liquid phase yields were 55.50%, 48.73%, and 48.20% (wt.), at 345, 405, and 420°C, respectively, showing a smooth sigmoid behavior, decreasing with increasing temperature, while that of gas phase were 31.69%, 36.60%, and 40.13% (wt.), respectively, increasing with temperature. The liquid products density, kinematic viscosity, and refractive index obtained at 30, 40, 50, 60, 70, 80, and 110 minutes, varied between 0.9227 and 0.9380 g/mL, 0.566 and 0.588 mm2/s, and 1.401 and 1.414, respectively, showing percentage deviations between 0.74 and 2.36%, 7.40 and 10.86%, and 0.00 and 0.92%, respectively, compared to standard values for density, kinematic viscosity, and refractive index of pure MMA at 20 °C. The GC-MS identified in the reaction liquid products at 345, 405, and 420°C, 1.0 atm, esters of carboxylic acids, alcohols, ketones, and aromatics, showing concentrations of MMA between 83.454 and 98.975% (area.). For all the depolymerization experiments, the concentrations of MMA in the liquid phase, between 30 and 80 minutes, reach purities above 98% (area.), decreasing drastically with increasing reaction time after 100 minutes, thus making it possible to depolymerize the cross-linked PMMA-based dental resins scraps by pyrolysis to recover MMA. The optimum operating conditions to achieve high MMA concentrations, as well as elevated yields of liquid reaction products were 345 °C and 80 minutes.

The Mexican Republic ranks fifth in the world in terms of amphibian diversity, and within Mexico, the state of Oaxaca has the greatest amphibian richness and endemism. Unfortunately, various factors, such as land use change and global warming, have caused a global crisis that threatens the conservation of this class. In the state of Oaxaca, few studies of amphibians have been carried out at the state level. Several research has shown that an analysis of beta diversity provides information that can be applied to conservation strategies. In this work, we analyzed the beta diversity at the species level and higher taxon level for the amphibians of Oaxaca and their replacement components and the differences in richness for anurans and caudates separately between physiographic subprovinces. Very high beta diversity was recorded, with higher diversity occurring among caudates than among anurans. Replacement was the component that most contributed to this result, and the subprovinces with substantial environmental differences had the most dissimilar amphibian communities. The results of this study show the need to implement conservation strategies in subprovinces with high amphibian richness and endemism levels, following the example of Sierra Madre de Oaxaca (SMO)

This work aims to investigate the effect of catalyst content and reaction time by catalytic upgrading from pyrolysis vapors of residual fat at 450 °C and 1.0 atmosphere, on the yields of reaction products, physicochemical properties (density, kinematic viscosity, refractive index, and acid value) and chemical composition of organic liquid products (OLP), over a catalyst fixed bed reactor, in semi pilot scale. Pellets of Red Mud chemically activated with 1.0 M HCl were used as catalysts. The experiments were carried out at 450 °C and 1.0 atmosphere, using a process schema consisting of a thermal cracking reactor of 2.0 L coupled to a catalyst fixed bed reactor of 53 mL, without catalyst and using 5.0, 7.5, and 10.0% (wt.) Red Mud pellets activated with 1.0 M HCl, in batch mode. Samples of liquid phase products were withdrawn during the course of reaction at 40, 50, 60, 70 and 80 min in order to analyze the process kinetics. The physicochemical properties (density, kinematic viscosity, acid value, and refractive index) of OLP were determined by official methods. The chemical functions present in OLP determined by FT-IR and the chemical composition by GC-MS. The thermal catalytic cracking of residual fat show OLP yields from 54.4 to 84.88 (wt.%), aqueous phase yields between 2.21 and 2.80 (wt.%), solid phase yields (coke) between 1.30 and 8.60 (wt.%), and gas yields from 11.61 to 34.22 (wt.%). The yields of OLP increases with increasing catalyst content while those of aqueous, gaseous and solid phase decreases. For all the thermal and thermal catalytic cracking experiments, the density, kinematic viscosity, and acid value of OLP decreases with increasing reaction time. The GC-MS of liquid reaction products identified the presence of hydrocarbons (alkanes, alkenes, cycloalkanes, and aromatics) and oxygenates (carboxylic acids, ketones, esters, alcohols, and aldehydes). For all the thermal and thermal catalytic cracking experiments, the hydrocarbon content within OLP increases with reaction time, while those of oxygenates decrease, reaching concentrations of hydrocarbons up to 95.35% (area.). The best results for the physicochemical properties (density, kinematic viscosity, and acid value) and the maximum hydrocarbon content of OLP were obtained at 450 °C and 1.0 atmosphere, using a catalyst fixed bed reactor, with 5.0% (wt.) Red Mud pellets activated with 1.0 M HCl as catalyst.

This work aims to investigate systematically the influence of process temperature and biomass-to-water ration on the chemical composition of aqueous and gaseous phases and mass production of chemical by hydrothermal processing of Açaí (Euterpe Oleraceae, Mart.) seeds. The hydrothermal carbonization carried out at 175, 200, 225, and 250 °C, 2 °C/min, biomass-to-water ratio of 1:10, and at 250 °C, 2 °C/min, and biomass-to-water ratios of 1:10, 1:15, and 1:20, in technical scale. The chemical composition of aqueous phase determined by GC and HPLC and the volumetric composition of gaseous phase by using an infrared gas analyzer. For constant biomass-to-water ratio of 1:10, the yields of solid, liquid, and gaseous phases varied between 53.39 and 37.01% (wt.), 46.61 and 59.19% (wt.), and 0.00 and 3.80% (wt.), respectively. The yield of solids shows a smooth exponential decay with temperature, while that of liquid and gaseous phases a smooth growth. By variation of biomass-to-water ratios, the yields of solid, liquid, and gaseous reaction products varied between 53.39 and 32.09% (wt.), 46.61 and 67.28% (wt.), and 0.00 and 0.634% (wt.), respectively. The yield of solids decreases exponentially with increasing water-to-biomass ratio and that of liquid phase increases in a sigmoid fashion. For constant biomass-to-water ratio, the concentrations of Furfural and HMF decrease drastically with temperature, reaching a minimum at 250 °C, while that of phenols increases. In addition, the concentrations of CH3COOH and total carboxylic acids increase, reaching a maximum at 250 °C. For constant process temperature, the concentrations of aromatics vary smoothly with the temperature. The concentrations of furfural, HMF, and cathecol decrease with temperature, while that of phenols increases. The concentrations of CH3COOH and total carboxylic acids decrease exponentially with temperature. Finally, for the experiments with varying water-to-biomass ratios, the productions of chemicals (furfural, HMF, phenols, cathecol, and acetic acid) in the aqueous phase is highly dependent on the biomass-to-water ratio.

The Yellow-legged Hornet (Vespa velutina nigrithorax) (YLH) is an invasive insect that arrived in Europe in 2004 and is now spread across nine countries. It is a threat to the native entomofauna and harmful to beekeeping and agriculture, as it is a ravenous predator of the European Honey Bee (Apis mellifera) and other pollinating species. Its expansion has been unstoppable and all resources are needed to fight against it, including native vertebrate predators. Among these, the European Bee-eater (Merops apiaster) (EBE) is a potential one, but little is known about its predation on YLH. In a study carried out in Portugal, remains of YHL were detected in EBE nesting sites, which to the best of our knowledge is the first such report. This means that this bird could be one more agent in the biological control of this pest (although research on predation intensity is still needed), in conjunction with other natural predators and other strategies. In the Iberian Peninsula both species are allopatric in vast regions, so the role of EBE may be more limited. However, in the rest of Europe, at a country or continent scale, the scenario may be different and sympatry may occur to a greater extent.

The study of innovation in the public sector has attracted increasing interest in the last decade. Contributions of the literature concerning its possible innovation drivers and inhibitors have primarily had a theoretical or documentary perspective; empirical studies are scarce, as are work-team studies in organizations of this sector. The present study therefore focuses on identifying and understanding those variables or factors that induce or inhibit innovative activity in work teams in public organizations in a developing country. The research focus is qualitative, and 16 directors of 13 public Costa Rican institutions were interviewed for the study. A set of coding methods allowed to identify 19 thematic categories of variables linked to the capacity to generate innovations in these work teams.

Verminosis causes great damage to the producer, with reduced milk production and decreased development of young animals. The use of bioproducts are an alternative to control worms. This study evaluated the effects of oral administration of one commercial formulations, based on the fungus Duddingtonia flagrans (Bioverm®) and experimental formulations D. flagrans associated with Pochonia chlamydosporia, on the control of worms in naturally infected cattle on February pasture to October 2021. Eighteen Holstein x Zebu cattle were divided into groups of six animals (group 1 Bioverm®, group 2 Association and control), separated into paddocks naturally infected with helminth larvae (L3). The parasite load was by means of fecal samples and pasture collection to determine L3 infestation. The study demonstrated low recovery of L3 in the pasture due to low rainfall during the experiment. The EPG was lower in groups 1 and 2 compared to the control in April, May and July, while in March the values were lower only in treatment 1 compared to the control. Individual or combined administration of fungal products reduced the presence of eggs and larvae in pastures at certain months of the year, indicating their effectiveness in the strategic control of gastrointestinal parasites in cattle.

“De-[Constructing] Growth” is offered as a deeper and more useful conceptualization that avoids the negative connotations of, and resistance to, “degrowth” by decoupling profit from unsustainable consumption, production, and inequality.

The energy sector relies on numerical model output forecasts for operational purposes on a short-term scale, up to 10 days ahead. Reducing model errors is crucial, particularly given that coarse resolution models often fail to account for complex topography, such as that found in Costa Rica. Local circulations affect wind conditions at the level of wind turbines, thereby impacting wind energy production. This work addresses a specific need of the Costa Rican Institute of Electricity (ICE) as a public service provider for the energy sector. The developed and implemented product in this study serves as a proof of concept that could be replicated by WMO Members. It demonstrates a product for wind speed forecasting at wind power plants by employing a novel strategy for input selection based on large-scale indicators to enhance Artificial Intelligence-based forecasting methods. The product is developed and implemented based on the full-value chain framework for weather, water, and climate services for the energy sector introduced by the WMO. The results indicate a reduction of wind forecast RMSE by approximately 55% compared to the GFS grid values. The conclusion is that combining coarse model outputs with regional climatological knowledge through AI-based downscaling models is an effective approach for obtaining reliable local short-term wind forecasts up to 10 days ahead.

Mediterranean mountain landscapes feature pastoralism, and the maintenance of sheep and goat grazing is the main challenge for their sustainability. To deliver pastoralism ecosystem services, particularly in reducing fire risk amidst global change, it is essential to align the herds' size and impact with the current foraging status of the ecosystems in real time. This approach allows for more efficient herding, thereby maintaining the resilience of these landscapes. Understanding complex grazing processes at a landscape scale can now be aided by the various sensors and trackers available. The development of geolocation technologies makes it possible to combine information at different scales on time to adapt pastoralism more efficiently in the context of rural abandonment. In this paper, we analyze artificial intelligence-based IoT data from the daily routes of three flocks of goats and sheep over a year in the mountains of central Portugal. A principal components analysis of the temporal geolocalization of the herds discriminates the spatial scale of the territorial selection attributed to the herders and the animals, analytically confirming what has been described empirically by several authors. The results confirmed the relevance of these operational solutions for understanding complex landscape processes and efficiently supporting sustainable management. Finally, our result shows that these innovative tools are reliable for monitoring animal ecosystem services in Mediterranean mountain landscapes in support of policy decisions on their remuneration.

Antibodies are important tools for the study of membrane proteins in biological, biophysics and structural analyses. However, the production of purified membrane proteins is still a formidable challenge due to the amphipathic character and inherent instability of these proteins. In this work, we tested a strategy for producing antibodies against an ATP-Binding Cassette (ABC) transporter without the need to produce the full membrane complex. Instead, just the extra cytoplasmic regions of the ABC-type transporter Rv1819c from Mycobacterium tuberculosis were presented in the RAD-display, a scaffold system based on the engineered Pyrococcus furiosus RadA protein developed for exposition of peptides. The RadA scaffold protein is highly stable, can tolerate long insertions and easy to produce in Escherichia coli. Based on the three-dimensional structure of Rv1891c, we selected two versions of the main extracellular loops of the permease to use as test cases for this approach. Rv1819c-derived peptides displayed on RAD display system were used for immunization of mice and production of polyclonal antibodies. These antibodies were able to recognize the transporter in M. tuberculosis cell extracts, on intact cells by flow cytometry and as purified protein. The results showed the approach can be a useful tool for in vitro analyses, screening, and evaluation of different epitopes in membrane proteins.

In this work, the deoxygenation of organic liquid products (OLP) obtained by thermal catalytic cracking of palm oil at 450 °C, 1.0 atmosphere, with 10% (wt.) Na₂CO₃ as catalyst, in multistage countercurrent absorber columns using supercritical carbon dioxide (SC-CO₂) as solvent, with Aspen-HYSYS process simulator was systematically investigated. In a previous study, the thermodynamic data basis and EOS modeling necessary to simulate the deoxygenation of OLP has been presented [Molecules 2021, 26, 4382. https://doi.org/10.3390/molecules26144382]. This work address a new flowsheet, consisting of 0₃ absorber columns, 10 expansions valves, 10 flash drums, 08 heat exchanges, 01 pressure pump, and 0₂ make-up of CO₂, aiming to improve the deacidification of OLP. The simulation was performed at 333 K, 140 bar, and (S/F) = 17; 350 K, 140 bar, and (S/F) = 38; 333 K, 140 bar, and (S/F) = 25. The simulation shows that 81.49% of OLP could be recovered and the concentrations of hydrocarbons in the extracts of absorber-01 and absorber-02 were 96.95 and 92.78% (wt.) in solvent-free basis, while the bottom stream of absorber-03 was enriched in oxygenates compounds with concentrations up to 32.66% (wt.) in solvent-free basis, showing that organic liquid products (OLP) was deacidified and SC-CO₂ was able to deacidify OLP and to obtain fractions with lower olefins content. The best deacidifying conditions was obtained at 333 K, 140 bar, and (S/F) = 17.

The real-world outcomes of patients with metastatic prostate cancer (mPCa) are largely unexplored. We investigated the improvements in overall survival (OS) and cancer-specific survival (CSS) in patients with de novo mPCa in latest years. The USA SEER Research Data (2000-2017) were analyzed using the SEER*Stat software. The Kaplan-Meier method and Cox regression were used. Patients with de novo mPCa were allocated to 3 cohorts based on year of diagnosis: A (2000-2003), B (2004-2010), C (2011-2014). Maximum follow-up was fixed to 5 years. Overall, 26434 patients were included. Age, race and metastatic stage significantly affected OS and CSS. After adjustment for age and race, patients in cohort C showed 9% reduced risk of death (HR:0.91 [95% CI, 0.87-0.95], p<0.001) and 8% reduced risk of cancer-specific death (HR:0.91 [95% CI, 0.87-0.95], p<0.001) compared to those in cohort A. After adjustment for age, race and metastatic stage, patients in cohort C showed an improvement in OS and CSS compared to cohort B (HR:0.94 [95% CI, 0.91-0.97], p=0.001 and HR:0.89 [95% CI, 0.85-0.92], p<0.001). Patients with M1c disease had a more pronounced improvement in OS and CSS compared with the other stages. No differences were found between cohort B and C. In conclusion, the prognosis of de novo mPCa remains poor with a median OS of 30 months and a median CSS of 35 months. Limited OS and CSS improvements were observed in latest years.

The pre-emergent herbicide indaziflam is efficient in the management of weeds in eucalyptus crops, but this plant may develop less in soil contaminated with it. The objective was to evaluate the levels of chlorophylls a and b, the apparent electron transport rate (ETR), growth and dry matter of leaves, stems and roots of Clone I144, in clayey soil, contaminated with the herbicide indaziflam and the leaching potential of this herbicide. The design was completely randomized in a 3 x 5 factorial scheme, with four replications. Chlorophyll a and b contents, apparent electron transport rate (ETR), height growth and dry matter of leaves, stems and roots of Clone I144 were evaluated. The leaching of indaziflam in the clayey soil profile (69% clay) was evaluated in a bioassay with Sorghum bicolor, a plant with high sensitivity to this herbicide. The visual intoxication and height of this plant were evaluated at 28 days after sowing (DAS). Chlorophyll a and b contents and ETR, height and stem dry matter of Clone I144 were lower in soil contaminated with indaziflam residues. The dose of indaziflam, necessary to cause 50% (C50) of intoxication and the lowest height of sorghum plants, was 4.65 and 1.71 g ha-1 and 0.40 and 0.27 g ha-1 in clayey soil and sand, respectively. The sorption ratio (SR) of this herbicide was 10.65 in clayey soil. The herbicide indaziflam leached up to 30 cm depth at doses of 37.5 and 75 g ha-1 and its residue in the soil reduced the levels of chlorophylls a and b, the apparent electron transport rate (ETR) and the growth of Clone I144.

The prevalence of diagnosed cases of autism has increased rapidly, which raise interest in studying the variables related to the well-being of these families. The purpose of this paper is to review recent literature on other variables related to family well-being such a parenting styles. We conducted a systematic review using PRISMA check list and bias assessment ESTROBE with the aim of analyzing if the concepts of autism, well-being and parenting style are related. We screened 753 references, 16 full text articles and abstracts were read. It was identified that authoritative parenting style, those based on warmth, establishing relationships and emotional bonding, and low expressed emotion were positively related to family well-being. On the other hand, authoritarian, permissive and overprotective styles, as well as critical, punishing and training-based were negatively associated with well-being and quality of family life.

This study aims to evaluate how the operational procedure adopted for the pellets placement and the exposure to subsurface conditions influences the mechanical integrity of bentonite plugs used as barrier elements in the abandonment of petroleum wells. To this end, two methodologies were used to obtain the plugs: from the first methodology, the pellets were immersed in diesel or olefin, which are proposed as displacement fluids in offshore operations, and then, hydrated in deionized water; in the second methodology, representative of onshore operations, the pellets were directly hydrated in deionized water. After that, the plugs were tested by compression and adhesion tests. These mechanical tests were also carried out for test specimens obtained from plugs exposed to four formulations of synthetic formation waters. The results obtained demonstrated that the previous contact with olefin adversely affects the mechanical stability of bentonite plugs, while plugs formed from pellets immersed in diesel presented satisfactory mechanical properties. The mechanical properties of onshore plugs attested the highly successful performance of these elements, once its compressive strength was minimally impacted by exposure to formation waters and more pronounced reductions were observed only in the adhesion properties after the contact with higher salinity formation waters.

This work aims to investigate the influence of reaction time and catalyst-to-residual fat ratio by catalytic upgrading from pyrolysis vapors of residual fat at 400 °C and 1.0 atmosphere, on the yields of reaction products, physicochemical properties (density, kinematic viscosity, and acid value) and chemical composition of bio-oils, over a catalyst fixed bed reactor of activated carbon pellets impregnated with 10.0 M NaOH, in semi pilot scale. The experiments were carried out at 400 °C and 1.0 atmosphere, using a process schema consisting of a thermal cracking reactor of 2.0 L coupled to a catalyst fixed bed reactor of 53 mL, without catalyst and using 5.0, 7.5, and 10.0% (wt.) activated carbon pellets impregnated with 10.0 M NaOH, in batch mode. Samples of liquid phase products were withdrawn during the course of reaction at 50, 60, 70, 80, 90, 100 and 120 minutes in order to investigate the process kinetics. The physicochemical properties (density, kinematic viscosity, and acid value) of bio-oils were determined by official methods. The chemical composition of bio-oils determined by GC-MS. The thermal catalytic cracking of residual fat show bio-oils yields from 55.55 to 30.22 (wt.%), aqueous phase yields between 2.83 and 3.19 (wt.%), solid phase yields between 13.56 and 9.75 (wt.%), and gas yields from 27.89 to 55.60 (wt.%). The yields of bio-oil decreases from 74.41 to 30.22% (wt.) with increasing catalyst-to-Tallow kernel oil ratio, while that of gaseous phase increases from 12.87 to 55.60% (wt.). For all the thermal and thermal catalytic cracking experiments, the density, kinematic viscosity, and acid value of bio-oils decreases as the reaction time increases varying from 0.9266 to 0.8220 g/cm³, 8.10 to 2.24 mm²/s, and 144.14 to 2.37 mg KOH/g. The GC-MS of liquid reaction products identified the presence of hydrocarbons (alkanes, alkenes, ring-containing alkanes, ring-containing alkenes, and aromatics) and oxygenates (carboxylic acids, ketones, esters, alcohols, and aldehydes). For all the pyrolysis and catalytic cracking experiments, the hydrocarbon selectivity in bio-oil increases with increasing reaction time, while those of oxygenates decrease, reaching concentrations of hydrocarbons up to 95.35% (area.). The best results for the physicochemical properties density, kinematic viscosity, and acid value were 0.8220 g/cm³, 3.03 mm2/s, and 2.37 mg KOH/g, respectively, with a maximum hydrocarbon concentration of 97.194% (area.) and 2.806% ketones (area.) were obtained at 400 °C and 1.0 atmosphere, 80 minutes, without catalyst. For the catalytic cracking experiments, the maximum hydrocarbon content of 75.763% (area.) and 17.041% (area.) carboxylic acids, 4.702% (area.) ketones (area.), and 2.494% (area.) non-identified oxygenates was obtained at 400 °C and 1.0 atmosphere, 90 minutes, using a catalyst fixed bed reactor, with 10.0% (wt.) activated carbon pellets impregnated with 10.0 M NaOH as catalyst.

: Rasmussen’s encephalitis (RE) stands as a rare neurological disorder marked by progressive cerebral hemiatrophy and epilepsy resistant to medical treatment. Despite extensive study, the primary cause of RE remains elusive, while its histopathological features encompass cortical inflammation, neuronal degeneration, and gliosis. The underlying molecular mechanisms driving disease progression remain largely unexplored. In this case study, we present a patient with RE who underwent hemispherectomy and has remained seizure-free for over six months, experiencing gradual motor improvement. Further-more, we conducted molecular analysis on the excised brain tissue, unveiling a decrease in the expres-sion of cell cycle-associated genes coupled with elevated levels of BDNF and TNF-α proteins. These findings suggest potential involvement of cell cycle regulators in the progression of RE.

The plants Agave sisalana (sisal) and Punica granatum (pomegranate) are rich in saponins, which are secondary metabolites known for their therapeutic properties, including anti-inflammatory effects. Although, Brazil is the world's leading sisal producer, approximately 95% of the leaves are discarded after fiber extraction. Similarly, pomegranate peel waste is abundant in Brazil. To address the need for safe and effective anti-inflammatory treatments. This study aimed to create a topical mucoadhesive gel containing a combination of sisal (RS) and pomegranate residue ex-tracts (PR). In vitro experiments examined isolated and combined extracts, as well as the result-ing formulation, focusing on: 1) phytochemical analysis (total saponin content); 2) cytotoxicity (MTT assay); and 3) pharmacological assessment of anti-inflammatory activity (phagocytosis, macrophage spreading, and membrane stability).Results revealed saponin concentrations in grams per 100 grams of dry extract as follows: SR - 29.91 ± 0.33, PR - 15.83 ± 0.93, Association (A) - 22.99 ± 0.01, Gel Base (G1) - 0.00 ± 0.00, and Association Gel (G2) - 0.52 ± 0.05. In MTT tests for isolated extracts, cytotoxicity values (µg/mL) were 3757.00 for SR and 2064.91 for PR. Converse-ly, A and G2 exhibited no cytotoxicity, with increased cell viability over time. All three anti-inflammatory tests confirmed the presence of this activity in SR, PR, and A. Notably, G2 demon-strated an anti-inflammatory effect comparable to dexamethasone.In conclusion, the gel contain-ing SR and PR holds promise as a novel herbal anti-inflammatory treatment. Its development could yield economic, social, and environmental benefits by utilizing discarded materials in Brazil.

This study explores the impact of temperature and molarity on the pyrolysis of Açaí seeds (Euterpe Oleraceae, Mart.) activated with KOH on the yield of bio-oil, hydrocarbon content of bio-oil, antioxidant activity of bio-oil and chemical composition of aqueous phase. The experiments were carried out at 350, 400, and 450 °C and 1.0 atmosphere, with 2.0 M KOH, and at 450 °C and 1.0 at-mosphere, with 0.5 M, 1.0 M and 2.0 M KOH, in laboratory scale. The composition of bio-oils and aqueous phase determined by GC-MS, while the acid value, a physical-chemical property of fundamental importance in biofuels, of bio-oils and aqueous phases by AOCS methods. The antioxidant activity of bio-oils determined by the TEAC method. The solid phase (biochar) characterized by X-ray diffraction (XRD). The diffractograms identified the presence of Kalicinite (KHCO3) in bio-char, and those higher temperatures favor the formation peaks of Kalicinite (KHCO3). The pyrolysis of Açaí seeds activated with KOH show bio-oil yields from 3.19 to 6.79 (wt.%), aqueous phase yields between 20.34 and 25.57 (wt.%), solid phase yields (coke) between 33.40 and 43.37 (wt.%), and gas yields from 31.85 to 34.45 (wt.%). The yield of bio-oil shows a smooth exponential increase with temperature. The acidity of bio-oil varied between 12.3 and 257.6 mgKOH/g, decreasing exponentially with temperature, while that of aqueous phase between 17.9 and 118.9 mgKOH/g, showing and exponential decay behavior with temperature, demonstrating that higher temperatures favor not only the yield of bio-oil but also bio-oils with lower acidity. For the experiments with KOH activation, the GC-MS of bio-oil identified the presence of hydrocarbons (alkanes, alkenes, cycloalkanes, cycloalkenes, and aromatics) and oxygenates (carboxylic acids, phenols, ketones, and esters). The concentration of hydrocarbons varied between 10.19 to 25.71 (area.%), increasing with temperature, while that of oxygenates from 52.69 to 72.15 (area.%), decreasing with temperature. For the experiments with constant temperature, the concentrations of hydrocarbons in bio-oil in-crease exponentially with molarity, while those of oxygenates decrease exponentially, showing that higher molarities favor the formation of hydrocarbons in bio-oil. The antioxidant activity of bio-oils decreases with increasing temperature, as the content of phenolic compounds decreases, and de-creases with increasing KOH molarity, as higher molarities favors the formation of hydrocarbons. Finally, it can be concluded that chemical activation of Açaí seeds with KOH favors the not only the yield of bio-oil but also the content of hydrocarbons. The study of process variables is of utmost importance in order to clearly assess reaction mechanisms, economic viability and design goals that could be derived from chemically activated biomass pyrolysis processes.

This research explores the depolymerization of waste polymethyl methacrylate (PMMAW) from dental material in fixed-bed semi-batch reactors, focusing on three production scales: laboratory, technical, and pilot. The study investigates the thermal degradation mechanism and kinetics of PMMAW through thermogravimetric (TG) and differential scanning calorimetry (DSC) analyses, revealing a two-step degradation process. The heat flow during PMMAW decomposition is measured by DSC, providing essential parameters for designing pyrolysis processes. The results demonstrate the potential of DSC for energetic analysis and process design, with attention to standardization challenges. Material balance analysis across the production scales reveals a temperature gradient across the fixed bed negatively impacting liquid yield and methyl methacrylate (MMA) concentration. Reactor load and power load variables are introduced, demonstrating decreased temperature with increased process scale. The study identifies the influence of temperature on MMA concentration in the liquid fraction, emphasizing the importance of controlling temperature for efficient depolymerization. Furthermore, the research highlights the formation of aromatic hydrocarbons from the remaining char, indicating a shift in liquid composition during the depolymerization process. The study concludes that lower temperatures below 450 °C favor liquid fractions rich in MMA, suggesting the benefits of lower temperatures and slower heating rates in semi-batch depolymerization. The findings contribute to a novel approach in analyzing pyrolysis processes, emphasizing reactor design and economic considerations for recycling viability. Future research aims to refine and standardize the analysis and design protocols for pyrolysis and similar processes.

In this study, the objective is to analyze the economic viability of municipal household solid waste (organic matter + paper) for the production of gas, coke and biofuel through the pyrolysis and distillation process. The waste was collected in the city of Belém do Pará-Brazil and pre-treated at UFPA. The analyzed fraction (organic matter + paper) was subjected to pre-treatment of drying, crushing, sieving and was subsequently subjected to proximate characterization and finally pyrolysis of the organic fraction (organic matter + paper) in a fixed bed reactor. Initially, it was necessary to review the literature and with the yields obtained by pyrolysis of the frac-tion, economic feasibility analyzes were carried out. The economic indicators for evaluating the most viable pyrolysis process were: simple payback, discounted payback, net present value (NPV), internal rate of return (IRR), and profitability index (IL). The analysis of the indicators showed the economic viability considering an analysis horizon of 10 years, of materials based on organic material and paper. The break-even point obtained was 0.96 US$/L and the minimum biofuel sales price (MFSP – “Minimum Fuel Sale Price”) obtained in this work was 1.30 US$/L. The sensitivity analysis demonstrated that material costs (organic matter + paper), bio-oil yield, total project investment and electricity, respectively, are the variables that most affect the mini-mum biofuel sales price (MFSP).

The spread of antimicrobial resistance (AMR) is a global challenge. Close and continuous surveillance for quick detection of AMR can be difficult, especially in remote places. This narrative review focuses on the contributions of pharmacovigilance (PV) as an auxiliary tool for identifying and monitoring the ineffectiveness of, resistance to, and inappropriate use of antibiotics (ABs). The terms “drug ineffective,” “therapeutic failure,” “drug resistance,” “pathogen resistance,” and “multidrug resistance” were found in PV databases and dictionnaires, and denote ineffectiveness. These terms cover a range of problems that should be better investigated because they are useful in warning about possible causes of AMR. “Medication errors,” especially those related to dose and indication, are highlighted in the literature, suggesting inappropriate use of ABs. Hence, the included studies show that the terms of interest related to AMR are not only present but frequent in PV surveillance programs. This review illustrates the feasibility of using PV as a complementary tool for antimicrobial stewardship activities, especially in scenarios where other resources are scarce.

This work aims to investigate systematically the influence of process temperature, bio-mass-to-water ratio, and production scales (laboratory and pilot) on the chemical composition of aqueous and gaseous phases and mass production of chemical by hydrothermal processing of Açaí (Euterpe Oleraceae, Mart.) seeds. The hydrothermal carbonization carried out at 175, 200, 225, and 250 °C, 2 °C/min, biomass-to-water ratio of 1:10, and at 250 °C, 2 °C/min, and biomass-to-water ratios of 1:10, 1:15, and 1:20, in technical scale, as well as at 200, 225, and 250 °C, 2 °C/min, bio-mass-to-water ratio of 1:10, in laboratory scale. The elemental composition (C, H, N, S) of solid phase determined to compute the HHV. The chemical composition of aqueous phase determined by GC and HPLC and the volumetric composition of gaseous phase by using an infrared gas an-alyzer. For the experiments in pilot scale with constant biomass-to-water ratio of 1:10, the yields of solid, liquid, and gaseous phases varied between 53.39 and 37.01% (wt.), 46.61 and 59.19% (wt.), and 0.00 and 3.80% (wt.), respectively. The yield of solids shows a smooth exponential de-cay with temperature, while that of liquid and gaseous phases a smooth growth. By varying the biomass-to-water ratios, the yields of solid, liquid, and gaseous reaction products varied be-tween 53.39 and 32.09% (wt.), 46.61 and 67.28% (wt.), and 0.00 and 0.634% (wt.), respectively. The yield of solids decreases exponentially with increasing water-to-biomass ratio and that of liquid phase increases in a sigmoid fashion. For constant biomass-to-water ratio, the concentrations of Furfural and HMF decrease drastically with increasing temperature, reaching a minimum at 250 °C, while that of phenols increases. In addition, the concentrations of CH3COOH and total car-boxylic acids increase, reaching a maximum at 250 °C. For constant process temperature, the concentrations of aromatics vary smoothly with the temperature. The concentrations of furfural, HMF, and cathecol decrease with temperature, while that of phenols increases. The concentra-tions of CH3COOH and total carboxylic acids decrease exponentially with temperature. Finally, for the experiments with varying water-to-biomass ratios, the productions of chemicals (furfu-ral, HMF, phenols, cathecol, and acetic acid) in the aqueous phase is highly dependent on the biomass-to-water ratio. For the experiments in laboratory scale with constant biomass-to-water ratio of 1:10, the yields of solid ranged between 55.9 and 51.1% (wt.), showing not only a linear decay with tem-perature, but also a lower degradation grade. The chemical composition of main organic compounds (furfu-ral, HMF, phenols, cathecol, and acetic acid) dissolved in the aqueous phase in laboratory scale shows the same behavior of those in obtained in pilot scale.

Croton grewioides Baill., a species native to the Caatinga, popularly known as canela de cunhã, is used in traditional medicine to treat gastrointestinal diseases such as diarrhea, gastritis and stomach ulcers. This study aimed to identify the chemical composition of the essential oil of C. grewioides (OECG) and evaluate its antibacterial and antibiotic-modulating activities against both standard and multidrug-resistant bacteria. To analyze the compounds, present in the oil, gas chromatography coupled with mass spectrometry (GC/MS) and gas chromatography with flame ionization detector (GC/FID) techniques were used. In the bacteriological tests, the Minimum Inhibitory Concentration (MIC) was obtained using the broth microdilution technique. The modulating effect of the essential oil was determined by calculating the subinhibitory concentration followed by serial microdilution of the antibiotics. The MIC reduction factor (FRC) was calculated and its data expressed as a percentage. Analysis of the chemical composition identified the presence of the major compound estragole with a relative abundance of 50.34%. The MIC values obtained demonstrated efficacy in K. pneumoniae isolated from urine with MIC values of 512 µg/mL. OECG potentiated the effects of all antibiotics tested on S. aureus ATCC 29213, K. pneumoniae Carbapnemase, E. coli ATCC 25922 and S. aureus ATCC 29213 strains with their FRC of 97.65 %, 99.80 %, 99.85 % and 99.88 %, respectively. Thus, the essential oil of C. growioides presents synergistic effects when combined with the tested antibiotics, in addition to acting in the fight against bacterial resistance to antibiotics.

Fungal infections caused by Candida spp. are responsible for high hospital morbidity and mortality rates. Therefore, there is a continuous search for new antifungal medicines, particularly ones with anti-Candida activity. This review analyzed articles published between 2002 and 2023 considering the anti-Candida activity of chemical compounds identified or isolated in plants of the Anacardiaceae family. In addition, the in-silico prediction of the isolated compounds described was performed. The analysis of 35 studies showed that extracts, essential oils, and compounds from the anti-Candida activity were frequently determined in vitro using the minimum inhibitory concentration (MIC). The most commonly tested species were Candida albicans, C. tropicalis, C. parapsilosis, C. glabrata, C. krusei, and C. guilliermondii, respectively. Essential oils were the most used form (37% of the studies). The isolated compounds with antifungal effects include cardanol, estragole, trans-anethole, β-caryophyllene, myrcene, catechin-3-o-rhamnoside, β-sitosterol-3-O-glucoside, 24Z-isomasticadienolic acid, oleanolic acid, and oleanolic aldehyde. The in-silico evaluation of those isolated compounds revealed the compounds' drug-likeness and possible antifungal activity. However, some of them showed high toxicity. In conclusion, compounds from the Anacardiaceae family show promise for developing new therapeutic antifungal drugs, especially in combination with conventional antifungals.

The current investigation scrutinized the strategic approaches employed by the top four teams in the Brazilian Men's Volleyball Superliga, according to the match's opponent. The study encompasses the analysis of 22 matches, involving teams ranked first through fourth, competing against each of the 12 teams participating in the 21-22 season of the Brazilian Men's Volleyball Superliga, including one home and one away match for each team. Utilizing social network analysis facilitated the identification of the interconnections and particularities among all variables, offering a comprehensive perspective. The findings unveiled that during the offensive phase, the second, third, and fourth-ranked teams consistently exhibited higher eigenvector values, irrespective of the opposing team, notably when the middle-blocker positioned themselves in front and near the setter. Conversely, the championship-winning team displayed variations in offensive tactics. The team securing the second position demonstrated alterations in setting placement, whereas the other teams executed settings aimed at zones 3 and 4. Additionally, the initial setter's position at the commencement of a rally displayed varying eigenvector values based on the opponent, indicating team rotation as a performance determinant. Thus, barring the finalist team, the performance of the remaining teams is intricately intertwined with the individual characteristics of players.

This paper, based on the "Unified Theory of Forces," rigorously proves the formula of de Broglie's wave function. This helps us better understand the following important issues: 1) Theoretically prove and understand the essence of de Broglie's wave function; 2) Prove that when the particle's momentum P is determined, the greater the mass of the particle, the more concentrated its wave function distribution, and the weaker the interference effect; 3) Correct the spatial distribution of the wave function of free particles, proving that the wave function of free particles is strictly constrained within a finite spatial range, which is consistent with the facts we observe.

Recovery between physical efforts is essential for optimal performance in sports. Dietary supplements like cannabidiol (CBD) have been proposed to facilitate recovery and performance optimization. This systematic review aimed to: a) systematize the scientific evidence on CBD for recovery, b) associate CBD's biomedical properties with those required for optimal fatigue recovery, and c) recommend a future research agenda. Searches across databases identified 70 relevant studies from 1990-2022, including 38.6% preclinical, 31.4% clinical trials, and 30.0% reviews/meta-analyses across various populations like mice, rats, epileptics, and athletes. CBD demonstrated potentially beneficial properties for athlete recovery such as anti-inflammatory, neuroprotective, anxiolytic, and analgesic effects with doses ranging from 5-600mg administered orally, intravenously, and via other routes. However, rigorous confirmatory research specifically in athlete populations is lacking. While CBD appears promising for facilitating recovery and performance optimization, further randomized placebo-controlled trials are needed to test the acute and chronic effects of different CBD dosing regimens in athletes. Future research should focus on elucidating CBD's physiological mechanisms of action as they relate to post-exercise recovery, as well as its comparative effectiveness versus conventional medications and therapies. Advancing our understanding of CBD's role in athlete recovery could provide new therapeutic strategies to optimize recovery and performance.

In order to study the burrowing crab Neohelice granulata (Dana, 1851) in the northern limit of its distribution and to test the hypothesis that mesoscale factors are more deterministic than latitudinal variation in this crab life history, the population dynamics of this specie was studied in the Caceribú river (Rio de Janeiro state, Brazil). The sex ratio was female-biased over the year. Males were significantly larger (t-test = 3.53, p < 0.05) than females (CW mean = 29.14 mm and 27.32 mm, respectively), which were predominant in the intermediary-size classes. The breading season took place from February to November, with a peak in May. The recruitment was observed all over the year, but mostly from October to December. The size at maturity was estimated at 19.0 mm for females and 23.9 mm for males. Average fecundity was 20,419 eggs (±12,627.12) and showed a decrease from the first to the last stage of embryonic development. The asymptotic size was similar between males (CW∞ = 24.86 mm) and females (CW∞ = 24.50 mm). Longevity was estimated in 1.33 and 1.23 years in males and females, respectively. Mortality rates were slightly higher in males (Z = 3.71) than in females (Z 0 3.41). Analysing the results of this study and the literature we conclude that the population dynamics of N. granulata do not follow a latitudinal trend. This strengthens the hypothesis that brachyurans’ life histories are mainly driven by mesoscales factors than latitudinal variation.

The use of Information Communication Technologies (ICT) in education brings up new possibilities of promoting the learning and health experiences. In this sense, education contexts of 21st century must consider these two areas of knowledge, especially their integration. This article presents learning practices developed with mobile devices and games, in order to improve learning and well-being in children and adolescents undergoing cancer treatment in non-formal educational setting. The methodology is based on qualitative case studies with content-based data analysis, involving informal interviews and observation methods. The study considers data from 5 patients who participated in the research between 2015 and 2019. The results demonstrate a positive influence of the practices with mobile technologies and games in terms of learning and in the well-being feeling of patients during the treatment.

Este estudio empleó el algoritmo MaxEnt para evaluar la distribución potencial de la serpiente de cascabel de cola larga, Crotalus stejnegeri , una especie amenazada endémica de México. Los resultados demuestran una buena fiabilidad del modelo, alcanzando un AUC de 0,879. Destacan una distribución potencial concentrada en las estribaciones de la Sierra Madre Occidental, principalmente en el centro-sur de Sinaloa, suroeste de Durango y norte de Nayarit, caracterizada por bosque seco tropical. La temperatura durante el trimestre más seco y la estacionalidad de la precipitación se identifican como factores determinantes, mientras que la baja idoneidad en Chihuahua sugiere una afinidad tropical de la especie. La variabilidad en las precipitaciones durante el trimestre más frío enfatiza la importancia de ampliar el número de registros de ocurrencia de la especie mediante una mayor exploración de campo dentro de su área de distribución. Estos hallazgos proporcionan información valiosa para los esfuerzos de conservación y subrayan áreas clave para futuras investigaciones.

The COVID-19 pandemic crisis has brought about unprecedented economic and social consequences worldwide. The implementation of isolation measures, including national and international travel restrictions, significantly affected contact-intensive sectors such as tourism. During this lockdown period, Information and Communication Technology (ICT) was crucial in maintaining connectivity and enabling remote activities. Governments across the world implemented discretionary measures to mitigate the crisis's adverse effects on economic activity. This paper aims to analyze whether the level of ICT adoption and the importance of tourism influence the fiscal policy efforts pursued by governments. Based on the results of a linear regression analysis for 154 countries, the findings suggest that in countries with higher international tourism receipts, the governments had to promote higher fiscal stimulus. At the same time, ICT development diminished the efforts of the fiscal policy response to the crisis since it facilitated economic resilience. The findings of this study can contribute to understanding how governments responded to the pandemic crisis and the factors that influenced their fiscal policy decisions.

This paper analyses the viability of different solutions to passively augment the axial stiffness of a horizontal axis radial levitation passive magnetic bearing (PMB) with topology previously studied. The zero-field cooling (ZFC) of high-temperature superconductor (HTS) bulks promotes higher magnetic impulsion and levitation forces and lower electromagnetic losses than with the field-cooling (FC), but on the other hand, the guiding stability is much lower than with FC. Because of stability reasons, FC was adopted in most superconducting maglev systems. The trend of this research group has been to develop an HTS ZFC horizontal axis radial levitation PMB presenting notable levitation forces with reduced electromagnetic losses, defined by a topology that creates guiding stability. Previous work has shown that even optimizing the bearing geometry to maximize magnetic guidance forces, could not be enough to guarantee the axial stiffness required for many applications. First, the extent to which guidance forces are augmented by increasing the number of HTS bulks in the stator is evaluated. Then, the axial stiffness augmentation by passively adding two limiting permanent magnet (PM) rings is evaluated. Results show that the axial stiffness is highly augmented by adding limiting PM rings with no significant additional investment. This change enables using the studied ZFC superconducting PMB in high-precision axial stability applications, such as precision gyroscopes, horizontal axis propellers and turbines.

Latin America and the Caribbean offer the most favorable natural and social conditions for the emergence of cattle ranching that regenerate and maintains the ecosystem services on which life on Earth depends, that is energy efficient and that contributes to meeting fundamental human food needs. Unlike other major global producers, cattle farming in Latin America and the Caribbean is fundamentally based on pasture. Therein lies both its strength (due to the regenerative potential of well-managed pastures) and its vulnerability (due to the pervasive link between deforestation and pasture formation, especially in the Amazon, where 40% of the Brazilian herd is concentrated). The diversification of pastures (today marked by impressive monotony, with brachiaria accounting for 85% of the species in Brazil), the introduction of legumes and tree plantations within them, and the proper management of herds, open the way to the possibility of drastically reducing the area currently occupied by the activity (especially in the Amazon) while maintaining the supply of its products. Agricultural research has disseminated forms of moderate intensification of cattle ranching, which represent a low opportunity cost of animal feed and, at the same time, regeneration of ecosystem services that have so far been destroyed by the prevailing methods of farming.

Industry 4.0 (I4.0) epitomizes the nexus of technological evolution and manufacturing process enhancements, underpinned by four critical pillars: Cyber-Physical Systems (CPS), Digital Twins (DT), the Industrial Internet of Things (IIoT), and Cloud Computing (CC). Through the lens of the German Reference Architectural Model Industrie (RAMI) 4.0, these components are integral to fostering Smart Manufacturing (SM) practices. In conjunction, the Asset Administration Shell (AAS) facilitates seamless inter-company communication and enables adaptability to fluctuating market demands. This paper delves into the structural intricacies of AAS and SM within the RAMI 4.0 framework, unveiling three distinct implementation strategies. Furthermore, it meticulously scrutinizes challenges that hinder the full realization of I4.0 potential, such as interoperability, security concerns, and standardized communication protocols. By examining these models and identifying current barriers, the study illuminates pathways for future research, particularly in enhancing the integration of AAS and SM systems, ensuring robust security measures, and advocating for the development of universal standards. This exploration aims to contribute to the ongoing discourse on I4.0, proposing avenues for advancing manufacturing technologies and operational frameworks in alignment with the principles of RAMI 4.0.

The ultimate goal of this paper was to examine the degree of elasticity between two variables, namely, agricultural credit and agricultural growth, in Angola in the period 2003–2022. Time series data were fitted into the ARDL test using various econometric techniques such as the ADF stationarity test, Granger causality and the ordinary least squares method as well as a vector error correction model (VECM) to analyze the relationship between agricultural credit and agricultural economic growth, showing a causal relationship. Both the impacts through elasticities and the optimal point existing in this relationship were estimated. It was concluded that the impact of agricultural credit on agricultural GDP was 14.41%. Granger causality shows signs of a positive linkage between agricultural credit and agricultural GDP. However, there is a causal relationship between agricultural credit and agricultural GDP, in a unidirectional aspect. This result is consistent with most of the earlier studies reviewed in the literature, confirming that credit-oriented monetary policies can boost economic growth and, consequently, development in Angola. It is important for agricultural credit systems to be designed in a way that ensures equitable access, fair interest rates, and appropriate risk management mechanisms. Additionally, monitoring and evaluation mechanisms should be in place to assess the environmental and social impacts of credit programs on agricultural sustainability. It is worth noting that this is a first-of-a-kind study on the matter of the Angolan credit experience, specifically for the agricultural sector. Angola is still searching for a sustainable credit model that could be used as a catalyzer to boost growth and contribute to economic development.

Objective: To evaluate the direct costs of treating patients with neuromyelitis optica spectrum disorders (NMOSD) in outpatient care, from a hospital and Unified Health System (SUS) perspective. Methods: Observational study with data collection by microfunding, carried out with patients diagnosed with neuromyelitis optics, treated at a university hospital, in the city of Rio de Janeiro. Mann-Whitney tests were performed to measure cost differences between patient groups by disease severity and analysis perspective. Results: Nine individuals with a median age of 48 years (IQR 30 - 59 years) were included. The median total costs for patients with greater severity from the perspective of the SUS and the hospital were R$ 21,638.22 (IIQ: R$ 15,614.63; R$ 25,985.32) and R$ 32,094.11 (IIQ: R$ 25,610 .60; R$ 38,617.25) respectively. For patients with moderate severity the median was R$ 7,339.85 (IIQ: R$ 6,235.45; R$ 11,912.05) from the SUS perspective and R$ 11,505.80 (IIQ: R$ 7,339.85; R$ 22,424.76) from the perspective of the hospital, where the use of medications had a major impact. Conclusion: The main cost drivers were medicines, especially those used off-label, and procedures.

The giant challenge breeding flood-irrigated rice is to identify superior genotypes that present high-yielding with specific grain qualities, resistance to abiotic and biotic stresses, excellent adaptation to the target environment. Thus, the objectives of this study were to propose a bayesian multi-trait model, estimate genetic parameters, and select flood-irrigated rice genotypes with better genetic potentials in different evaluation environments. For this, twenty-five rice genotypes belonging to the flood-irrigated rice improvement program were evaluated. The grain yields, grain length, width and thickness, grain length, and grain width and weight of 100 grains in the agricultural year 2016/2017. The experimental design used in all experiments was a randomized block design with three replications. The Monte Carlo Markov Chain algorithm estimated genetic parameters and genetic values. The grain thickness trait was considered highly heritable, with a credibility interval ranging from: h^2: 0.9480; 0.9440; 0.8610, in environments 1, 2, and 3, respectively. The grain yields showed a low correlation estimate between grain thickness and 100-grain weight, in all environments, with a credibility interval ranging from (ρ= 0.5477; 0.5762; 0.5618 and 0.5973; 0.5247; 0.5632, grain thickness and 100-grain weight, in environments 1, 2, and 3, respectively). The Bayesian multi-trait model proved to be an adequate strategy for the genetic improvement of flood-irrigated. Genotypes 2 and 15 had similar potential in the three environments, they should be selected as high-performance multi-trait genotypes for the genetic breeding of flood-irrigated rice in the program.

Degnala is one of the main mycotoxicoses that affects buffaloes, and the fungus Fusarium spp. is the main causative agent. This disease is strongly related to the supply of rice straw to buffaloes and is considered endemic to regions where this crop is cultivated. Cases of the disease are concentrated in the winter, when conditions favour fungal growth in inadequately stored rice straw. Degnala is characterized by necrosis and gangrene of the extremities, including the tail, lower limbs, ears, tongue, muzzle and teats. The pelvic limbs are more affected than the thoracic limbs. A tortuous appearance of the tail is very common, and cracks or corneal loss of the hooves may occur, with exposure of the blades and even the bones. There is no diagnostic method for identifying the disease in animals other than the clinical and epidemiological criteria associated with fungal culture of rice straw samples. There is no treatment that neutralizes the effects of the toxins, and the treatment currently used is a palliative and supportive method consisting of pentasulfate solution, anti-Degnala liquid, 2% nitroglycerin ointment and broad-spectrum antibiotics for secondary infections. In addition, the management of drying straw and proper storage are essential for controlling this disease.

Traditional computer vision techniques aim to extract meaningful information from images but often depend on manual feature engineering, making it difficult to handle complex real-world scenarios. Fractional Calculus (FC), which extends derivatives to non-integer orders, provides a flexible way to model systems with memory effects and long-term dependencies, making it a powerful tool for capturing fractional rates of variation. Recently, Neural Networks (NNs) have demonstrated remarkable capabilities in learning complex patterns directly from raw data, automating computer vision tasks and enhancing performance. Therefore, the use of fractional calculus in neural network-based computer vision is a powerful method to address existing challenges by effectively capturing complex spatial and temporal relationships in images and videos. This paper presents a survey of Fractional Calculus Neural Network-based (FC NN-based) computer vision techniques for denoising, enhancement, object detection, segmentation, restoration, and NN compression. The survey compiles existing FFC NN-based approaches, elucidates underlying concepts, and identifies open questions and research directions. By leveraging FC's properties, FC NN-based approaches offer a novel way to improve the robustness and efficiency of computer vision systems.

Oral mucosa is a key player in the cancer patient and during cancer treatment. The increasing prevalence of cancer and cancer therapy associated side effects are behind the major role that oral mucosa plays in the oncological patient. Oral mucositis is a debilitating severe complication caused by early toxicity of chemo and/or radiotherapy that can restrict treatment outcome possibilities, even challenging patient’s survival. It has been referred to as the most feared cancer treatment complication. Predictive variables as to who and to what extent will be affected are still unclear. Additionally, oral mucositis is one of the sources of the increasing economic burden of cancer, not only for patients and their families but also for institutions and governments. All efforts should be implemented in the search for new approaches to minimize the apparently ineluctable outburst of oral mucositis along the cancer treatment. New perspectives derived from different approaches in explaining the interrelation between oral mucositis and oral microbiome or the similarities with genitourinary mucosa may help elucidate the biomolecular pathways and mechanisms behind oral mucosa cancer-therapy related toxicity and what is more important its management in order to minimize treatment side effects and to provide enhanced cancer support.

The approach to the personal experience and previous ideas about Physical Education of future Primary Education teachers is a starting point of great interest for the teaching of the subject of Didactics of Physical Education. The study aims to investigate these prior beliefs and to verify to what extent this initial perception changes after taking the course on “Didactics of Physical Education”. A concurrent mixed-methods study was conducted, which included two data collection procedures: (1) a pre-experimental design with a single group featuring pre-test and post-test; (2) the analysis of students' autobiographical accounts of their school experience with physical education. The participants were students enrolled in the Bachelor’s degree program in Primary Education at the University of Santiago de Compostela (USC) who undertook the course last year. The results obtained reveal that after taking the subject of Didactics of Physical Education, students give greater value to more positive concepts of learning, socializing, participating, and playing, among others. Similarly, in the post-test, the assessment of concepts such as competitiveness and physical fatigue diminished. In their autobiographical memories, students associate good memories with relationships with classmates and the playful and socializing nature of the subject; and among the bad memories, they highlight the content related to physical performance, competitiveness, and lack of attention to the diversity of students and their individual characteristics.

Ethical considerations regarding our treatment of animals have gained strength, leading to legislation and a societal focus across various disciplines. This is a subject of study within curricula related to agri-food sciences. The aim was to determine the perceptions of agronomy university students concerning animal welfare in livestock production systems. A survey was conducted to encompass various aspects, from participants' sociodemographic attributes to their attitudes and behaviors regarding animal welfare and the consumption of animal products. Statistical analysis, performed using R software, delved into the associations between participants' characteristics and their perspectives on the ethical, bioethical, and legal dimensions of animal welfare. Associations between demographic factors and ethical viewpoints among students were identified. Gender differences emerged in animal treatment perceptions, while rural and urban environments impacted perspectives on various animals. Bioethical considerations revealed distinctive disparities based on gender and education in concerns for animal welfare, value perceptions, evaluations of animal behaviors, and opinions on animal research. It is crucial to distinguish between animal welfare and ethical considerations arising from coexisting with sentient beings capable of experiencing suffering. Ethical theories provide a lens through which we perceive our obligations toward animals. The responsibility to ensure animal welfare is firmly rooted in recognizing that animals, like humans, experience pain and physical suffering. Consequently, actions causing unjustified suffering or mistreatment, particularly for entertainment purposes, are considered morally unacceptable.

This study aims to report the clinical signs, therapy, necropsy, and histopathological findings of the first case of airsacculitis caused by enterobacteria and eggs of the superfamily Diplotriaenoidea in M. choliba in the Amazon Biome. The bird was admitted without clinical signs, had been hospitalized for observation for five months, and had started the rehabilitation process for release 37 days before it started to show signs of weakness, lack of appetite, cachexia, dyspnea, ruffled feathers, vomiting, and dry feces. Therapy with oxytetracycline (48 mg/kg), sulfamethoxazole (48 mg/kg), mebendazole (25 mg/kg), potenay (0.5 ml/kg), sodium chloride 0.9% (50 ml /kg) and mercepton (5ml/kg), however, after five days of starting the treatment, the bird died. At necropsy, prominence of the keel, pieces of food in the oral cavity and proventriculus, thickened air sacs, intestine with firm stools, and the presence of gas, hepatomegaly, and splenomegaly were observed. The parasitological examination showed eggs of the Diplotriaenoidea superfamily. The microbiological analysis identified Escherichia coli, Klebsiella pneumoniae, and Enterobacter aerogenes. Histopathological examination showed heterophilic bacterial airsacculitis. The diagnosis was confirmed through clinical signs, necropsy findings, and parasitological, microbiological, and histopathological examination results.

This paper proposes an upper bound for mine productivity and also a simple truck dispatch rule that demonstrates how tight the upper bound can be using simulation. It also proposes a greedy search to approximate the productivity upper bound, which is faster and often exact. Uncertainty is added to the simulation in order to verify how the productivity responds to it. Typically, the productivity upper bound is less tight close to its saturation point as a function of the number of trucks, where adding more trucks only increases queues. Furthermore, more uncertainty in the model typically leads to a less tight upper bound. The results are conducted using real data from an open pit mine in Brazil.

This work aims to investigate systematically the tecno-economic feasibility of ther-mos-catalytic cracking process for two solid waste materials, a lipid-base material (re-sidual fat/scum from retention box of the University Restaurant of UFPA) and a lig-nin-cellulosic material Açaí seed (Euterpe oleracea. Mart). The thermo-catalytic process-es were carried out in pilot scale (THERMTEK/LEQ/UFPA/IME/RJ), and their economic feasibility analyzed. The yields of biofuels produced by fractional distillation were al-so studied. The physicochemical characteristics of the raw materials, the organic liquid product (bio-oil) and the chemical composition of kerosene, light-diesel and heavy-diesel from the lipid-base material, as well as those of kerosene and light-diesel from the Açaí seed were also determined. The economic indicators for the evaluation of the most viable cracking (pyrolysis) and distillation process of bio-oils were: a) the sim-ple payback criterion, b) discounted payback, c) net present value (NPV), d) internal rate of return (IRR), and e) index of profitability (IP). The analysis of the indicators showed the economic viability of crude palm oil (Elaeis guineensis, Jacq) and unfeasibil-ity for the palm oil neutralization. The minimum fuel selling price (MFSP) obtained is this work for the biofuels was of 1.34 US$/L) and the breakeven point obtained was of 1.28 US$/L. The sensibility analysis demonstrated that the pyrolysis and distillation yields are the most important variables to affect the minimum fuel selling price (MFSP).

This study aims to report the clinical signs, therapy, necropsy, and histopathological findings of airsacculitis caused by enterobacteria and the occurrence of the superfamily Diplotriaenoidea eggs in the feces of Megascops choliba in the Amazon Biome. A tropical screech owl nestling was rescued and admitted for hand-rearing. The animal was bred for five months. The feed was based on Zophobas morio larvae and thawed chicken breast meat with vitamin and mineral supplements. On the 37th day of hacking training for release, the owl showed weakness, lack of appetite, regurgitation, cachexia, dyspnea, ruffled feathers, dry feces in the vent and peri cloaca, and diarrhea. The parasitological examination showed eggs of the Diplotriaenoidea superfamily in the feces. The therapy was with oxytetracycline (48 mg/kg), sulfamethoxazole (48 mg/kg), mebendazole (25 mg/kg), potenay (0.5 ml/kg), sodium chloride 0.9% (50 ml /kg) and mercepton (5ml/kg). However, after five days of starting the treatment, the bird died. At necropsy, prominence of the keel, pieces of undigested food in the oral cavity and proventriculus, intestinal gas, and thickened and turbid air sacs were found. The microbiological analysis of air sacs identified Escherichia coli, Klebsiella pneumoniae, and Enterobacter aerogenes. Histopathological examination showed heterophilic bacterial airsacculitis.This study aims to report the clinical signs, therapy, necropsy, and histopathological findings of the first case of airsacculitis caused by enterobacteria and eggs of the superfamily Diplotriaenoidea in M. choliba in the Amazon Biome. The bird was admitted without clinical signs, had been hospitalized for observation for five months, and had started the rehabilitation process for release 37 days before it started to show signs of weakness, lack of appetite, cachexia, dyspnea, ruffled feathers, vomiting, and dry feces. Therapy with oxytetracycline (48 mg/kg), sulfamethoxazole (48 mg/kg), mebendazole (25 mg/kg), potenay (0.5 ml/kg), sodium chloride 0.9% (50 ml /kg) and mercepton (5ml/kg), however, after five days of starting the treatment, the bird died. At necropsy, prominence of the keel, pieces of food in the oral cavity and proventriculus, thickened air sacs, intestine with firm stools, and the presence of gas, hepatomegaly, and splenomegaly were observed. The parasitological examination showed eggs of the Diplotriaenoidea superfamily. The microbiological analysis identified Escherichia coli, Klebsiella pneumoniae, and Enterobacter aerogenes. Histopathological examination showed heterophilic bacterial airsacculitis. The diagnosis was confirmed through clinical signs, necropsy findings, and parasitological, microbiological, and histopathological examination results.

This work aims to investigate systematically the tecno-economic feasibility of ther-mos-catalytic cracking process for two solid waste materials, a lipid-base material (re-sidual fat/scum from retention box of the University Restaurant of UFPA) and a lig-nin-cellulosic material Açaí seed (Euterpe oleracea. Mart). The thermo-catalytic process-es were carried out in pilot scale (THERMTEK/LEQ/UFPA/IME/RJ), and their economic feasibility analyzed. The yields of biofuels produced by fractional distillation were al-so studied. The physicochemical characteristics of the raw materials, the organic liquid product (bio-oil) and the chemical composition of kerosene, light-diesel and heavy-diesel from the lipid-base material, as well as those of kerosene and light-diesel from the Açaí seed were also determined. The economic indicators for the evaluation of the most viable cracking (pyrolysis) and distillation process of bio-oils were: a) the sim-ple payback criterion, b) discounted payback, c) net present value (NPV), d) internal rate of return (IRR), and e) index of profitability (IP). The analysis of the indicators showed the economic viability of crude palm oil (Elaeis guineensis, Jacq) and unfeasibil-ity for the palm oil neutralization. The minimum fuel selling price (MFSP) obtained is this work for the biofuels was of 1.34 US$/L) and the breakeven point obtained was of 1.28 US$/L. The sensibility analysis demonstrated that the pyrolysis and distillation yields are the most important variables to affect the minimum fuel selling price (MFSP).

Background: Alzheimer's Disease (AD) is a progressive and incurable condition that prompts the exploration of interventions to slow its advancement and enhance the quality of life. The cortical brain waves could have a role in the process of executive function deterioration, increasing dementia symptoms. Objective: To interrogate the effects of physical exercise, and non-invasive brain stimulation, both in electrophysiological behavior of the brain, the executive functions, and dementia symptoms in older adults with AD. Methods: One hundred and sixteen older adults were grouped (n=22 each): GAE (AD, PMED+NIBS), GCP (AD, PMED), GCN (AD, NIBS), GCS (control, no intervention). Binaural beats were used as a non-invasive brain stimulation, physical exercise, or both, were applied during 16 weeks. Pre/post measurements included Alpha Band, and SMR Rhythms, executive functions, and dementia symptoms. Results: GCS showed no significant changes (p>0.05). GCN and GCS slightly enhanced inhibitory control (p>0.05) and working memory (p>0.05). In contrast, GCP and GAE improved executive function (p

(1) Background: Attention Deficit Hyperactivity Disorder (ADHD) and Developmental Language Disorder (DLD) are neurodevelopmental disorders that affect various areas of chil-dren’s development, such as language. There is an emerging idea that ADHD is characterised by the presence of language difficulties, which could be explained by the high comorbidity between ADHD and DLD. The purpose of this study is to analyse the empirical evidence of language com-petence in children aged 6–17 years old, diagnosed with ADHD and/or DLD. (2) Method: Fifteen studies with experimental designs were identified from Scopus, PsycINFO and WoS databases, reporting on language skills in children diagnosed with ADHD and/or DLD. Studies relating ex-ecutive functioning to language skills in this target population were also included. (3) Results: The literature is heterogeneous and different components of language are also examined. Even though the results are contradictory they convincingly demonstrate that there are overlapping symptoms between ADHD and DLD, such as language skills and executive functions. (4) Conclusions: the differences in the samples limit the generalisability of the results. Therefore, this review highlights the importance of considering language skills when designing individualised interventions for the population with ADHD and DLD, both in comorbidity and in isolation.

This work aims to investigate the effect of process temperature and catalyst content by pyrolysis and thermal catalytic cracking of (organic matter + paper) fraction from municipal household solid waste (MHSW) on the yields of reaction products (bio-oil, bio-char, H2O, and gas), acid value and chemical composition of bio-oils, and characterization of bio-chars, in laboratory scale. The collecting sectors of MHSW in the municipality of Belém-Pará-Brazil were chosen based on geographic and socio-economic database. The MHSW collected and transported to the segregation area. The gravimetric analysis of MHSW carried out and the fractions (Paper, Cardboard, Tetra Pack, Hard Plastic, Soft Plastic, Metal, Glass, Organic Matter, and Inert) separated. The selected organic matter and paper submitted to pre-treatment of crushing, drying, and sieving. The experiments carried out at 400, 450, and 475 °C and 1.0 atmosphere, and at 475 °C and 1.0 atmosphere, using 5.0, 10.0, and 15.0% (wt.) Ca(OH)2, in batch mode. The bio-oil characterized for acid value. The chemical functions present in bio-oil identified by FT-IR and the composition by GC-MS. The bio-char characterized by SEM, FT-IR and XRD. The variance in mass (wt.%) for organic fraction of municipal household solid waste, between 56.21 and 67.45% (wt.), lies with the interval of 56% (wt.) and 64% (wt.) of OFMHSW for middle and low income countries. The pyrolysis of MHSW fraction (organic matter + paper) show bio-oil yields between 2.63 and 9.41% (wt.), aqueous phase yields between 28.58 and 35.08% (wt.), solid phase yields between 35.29 and 45.75% (wt.), and gas yields between 16.54 and 26.72% (wt.). The bio-oil yield increases with pyrolysis temperature. For the catalytic cracking, the bio-oil and gas yields increase slightly with CaO content, while that of bio-char decreases, and the H2O phase remains constant. The GC-MS of liquid reaction products identified the presence of hydrocarbons (alkanes, alkenes, alkynes, cycloalkanes, and aromatics) and oxygenates (carboxylic acids, ketones, esters, alcohols, phenols, and aldehydes), as well as compounds containing nitrogen, including amides and amines. The acidity of bio-oil decreases with increasing process temperature and with aid Ca(OH)2 as catalyst. The concentration of hydrocarbons in bio-oil increases with increasing Ca(OH)2-to-MHSW fraction ratio due to the catalytic deoxygenation of fatty acids molecules, by means of de-carboxylation/de-carbonylation, producing aliphatic and aromatic hydrocarbons.

This article provides a comprehensive analysis of the global gas and liquefied natural gas (LNG) markets. The article begins by discussing the increasing demand for gas and LNG, particularly in Asia, as countries aim to transition to cleaner sources of energy. It explores how market volatility has led to energy security interventions and lasting economic and emissions impacts. It then explores the global supply and demand dynamics, highlighting the structural change expected in the market and the competition between Europe and Asia for limited new LNG supply. The article also focuses on Europe's increased flexibility and dependence on LNG imports, which have risen by 60% to 121 million tonnes, offsetting lower Russian pipeline imports. Furthermore, the article delves into global supply and demand dynamics, how the market is expected to remain tight, and how record gas and LNG prices have led to demand reductions. Additionally, it analyzes the future outlook and investment needs, highlighting the continued uptake of gas in heavy-duty transport and the need for further investment to avoid a supply-demand gap. The article concludes with an analysis of the implications for the future of the global gas and LNG markets.

In this paper we establish information theoretical bridges between 1) Thermal Heisenberg uncertainties $\Delta x \Delta p$ (at temperature $T$), and 2) LMC structural quantifiers. After having achieved such purpose, we determine to what an extent our bridges can be extended to both the semi classical and classical realms. Also, we find a strict bound relating a special LMC structural quantifier to quantum uncertainties.

Using pumps operating as turbines (PATs) offers the possibility of increasing the sustainability of water and energy systems by recovering the excess of energy that would be otherwise lost in pressure reducing valves or head loss chambers. In on-grid applications, there are many research works and implementations of PATs. However, there is still limited research for the optimization of efficiency and stability of PATs operating in off-grid systems. This work contributes to the development of stable direct current (DC) off-grid electric systems based on PATs, by optimizing and analysing the energy efficiency and stability for a wide range of operation. A self-excited induction generator (SEIG) coupled to the PAT is provided to cover the conventional type of electric ma-chines typically coupled to the hydraulic pumps. In this context, a methodology is proposed, based on the hydraulic, mechanical and electric subsystems, to define the PAT-SEIG operational area, to maximize energy conversion and the system efficiency. This will guarantee stable electric output quantities when operating in a DC off-grid system. In addition, an analytical model is proposed to estimate the PAT-SEIG operation under specific conditions. With this, water managers are suitable to design and optimize an off-grid PAT-SEIG system and to define the best hydraulic machines, electronic equipment, and all different control elements to maximize energy conversion within the target of operational limits. To develop and verify this new methodology, two micro PAT-SEIG setups were implemented in the hydraulic laboratory of IST/CERIS under typical operating conditions. The proposed solution proved to be resilient under a variable load regime. The system's maximum efficiency can be adapted using different capacitor values for the excitation of the SEIG, and the operational range is limited to the electric components. Considering the nominal efficiencies of the system’s components, the maximum p.u. efficiency obtained for each PAT-SEIG system were between 0.7 and 0.8 p.u.

This study explores the impact of temperature and molarity in the pyrolysis of Açaí seeds (Euterpe Oleraceae, Mart.) activated with KOH on the yield of bio-oil, hydrocarbon content of bio-oil, and chemical composition of aqueous phase. The experiments were carried out at 350, 400, and 450 °C and 1.0 atmosphere, with 2.0 M KOH, and at 450 °C and 1.0 atmosphere, with 0.5 M, 1.0 M and 2.0 M KOH, in laboratory scale. The composition of bio-oils and aqueous phase determined by GC-MS, while the acid value, a physico-chemical property of fundamental importance in bio-fuels, of bio-oils and aqueous phases by AOCS methods. The solid phase (biochar) characterized by X-ray diffraction (XRD). The diffractograms identified the presence of Kalicinite (KHCO3) in biochar, and those higher temperatures favor the formation peaks of Kalicinite (KHCO3). The pyrolysis of Açaí seeds activated with KOH show bio-oil yields from 3.19 to 6.79 (wt.%), aqueous phase yields between 20.34 and 25.57 (wt.%), solid phase yields (coke) between 33.40 and 43.37 (wt.%), and gas yields from 31.85 to 34.45 (wt.%). The yield of bio-oil shows a smooth exponential increase with temperature. The acidity of bio-oil varied between 12.3 and 257.6 mgKOH/g, decreasing exponentially with temperature, while that of aqueous phase between 17.9 and 118.9 mgKOH/g, showing and exponential decay behavior with temperature, demonstrating that higher temperatures favor not only the yield of bio-oil but also bio-oils with lower acidity. For the experiments with KOH activation, the GC-MS of bio-oil identified the presence of hydrocarbons (alkanes, alkenes, cycloalkanes, cycloalkenes, and aromatics) and oxygenates (carboxylic acids, phenols, ketones, and esters). The concentration of hydrocarbons varied between 10.19 to 25.71 (area.%), increasing with temperature, while that of oxygenates from 52.69 to 72.15 (area.%), decreasing with temperature. For the experiments with constant temperature, the concentrations of hydrocarbons in bio-oil increase exponentially with molarity, while those of oxygenates decrease exponentially, showing that higher molarities favor the formation of hydrocarbons in bio-oil. Finally, it can be concluded that chemical activation of Açaí seeds with KOH favors the not only the yield of bio-oil but also the content of hydrocarbons. The study of process variables is of utmost importance in order to clearly assess reaction mechanisms, economic viability and design goals that could be derived from chemically activated biomass pyrolysis processes.

This study explores the impact of temperature and molarity on the pyrolysis of Açaí seeds (Euterpe Oleraceae, Mart.) activated with KOH on the yield of bio-oil, hydrocarbon content of bio-oil, an-tioxidant activity of bio-oil and chemical composition of aqueous phase. The experiments were carried out at 350, 400, and 450 °C and 1.0 atmosphere, with 2.0 M KOH, and at 450 °C and 1.0 atmosphere, with 0.5 M, 1.0 M and 2.0 M KOH, in laboratory scale. The composition of bio-oils and aqueous phase determined by GC-MS, while the acid value, a physical-chemical property of fundamental importance in biofuels, of bio-oils and aqueous phases by AOCS methods. The an-tioxidant activity of bio-oils determined by the TEAC method. The solid phase (biochar) charac-terized by X-ray diffraction (XRD). The diffractograms identified the presence of Kalicinite (KHCO3) in biochar, and those higher temperatures favor the formation peaks of Kalicinite (KHCO3). The pyrolysis of Açaí seeds activated with KOH show bio-oil yields from 3.19 to 6.79 (wt.%), aqueous phase yields between 20.34 and 25.57 (wt.%), solid phase yields (coke) between 33.40 and 43.37 (wt.%), and gas yields from 31.85 to 34.45 (wt.%). The yield of bio-oil shows a smooth exponential increase with temperature. The acidity of bio-oil varied between 12.3 and 257.6 mgKOH/g, decreasing exponentially with temperature, while that of aqueous phase between 17.9 and 118.9 mgKOH/g, showing and exponential decay behavior with temperature, demonstrating that higher temperatures favor not only the yield of bio-oil but also bio-oils with lower acidity. For the experiments with KOH activation, the GC-MS of bio-oil identified the presence of hydro-carbons (alkanes, alkenes, cycloalkanes, cycloalkenes, and aromatics) and oxygenates (carboxylic acids, phenols, ketones, and esters). The concentration of hydrocarbons varied between 10.19 to 25.71 (area.%), increasing with temperature, while that of oxygenates from 52.69 to 72.15 (area.%), decreasing with temperature. For the experiments with constant temperature, the concentrations of hydrocarbons in bio-oil increase exponentially with molarity, while those of oxygenates de-crease exponentially, showing that higher molarities favor the formation of hydrocarbons in bio-oil. The antioxidant activity of bio-oils decreases with increasing temperature, as the content of phenolic compounds decreases, and decreases with increasing KOH molarity, as higher molarities favors the formation of hydrocarbons. Finally, it can be concluded that chemical activation of Açaí seeds with KOH favors the not only the yield of bio-oil but also the content of hydrocarbons. The study of process variables is of utmost importance in order to clearly assess reaction mechanisms, economic viability and design goals that could be derived from chemically activated biomass pyrolysis processes.

Objectives: To analyse and detail surgical process improvement activities that achieve the highest economic impact. Methods: Over 4 years, a team of technicians and healthcare professionals implemented a set of Lean surgical process improvement projects at Vall d’Hebron University Hospital (VHUH), Barcelona, Spain. These projects now form part of the daily routine in the surgical process. The economic impact on the hospital's surgical activity budget was analysed. Results: Process improvements have led to annual operational savings of over € 8.5 million. These improvements include better patient flow, better management of information between healthcare professionals, and improved logistic circuits. Conclusions: The current cultural shift towards process management in large hospitals implies shifting towards results-based healthcare, patient-perceived value (VBHC) and value-added payment. A Lean project implementation process requires long-term stability. The reason a considerable number of projects fail to complete process improvement projects is the difficulty involved in establishing the project and improving management routines. Few studies in the literature have investigated the economic impact of implementing Lean management a posteriori, and even fewer have examined actual cases. In this real case study, changes to surgical block management were initiated from zero. After being carefully thought through and designed, changes were carried out and subsequently analysed.

The bio-oil obtained by pyrolysis of Açaí (Euterpe oleracea Mart.) seeds at 450 ºC, 1.0 atmosphere, in technical scale, submitted to fractional distillation to produce biofuels-like fractions. The distillation of bio-oil carried out in a laboratory distillation column (Vigreux) of 30 cm. The physical-chemistry properties (density, kinematic viscosity, acid value and refractive index) determined by official methods. The chemical functions present in distillation fractions determined by FT-IR and the chemical composition by GC-MS. The distillation of bio-oil yielded gasoline, light kerosene, and kerosene-like fuel fractions of 16.16, 19.56, and 41.89% (wt.), respectively. All the physical-chemistry properties (density, kinematic viscosity, acid value and refractive index) increase with boiling temperature. The gasoline-like fraction is composed by 64.0% (area.) hydrocarbons and 36.0% (area.) oxygenates, while light kerosene-like fraction by 66.67% (area.) hydrocarbons and 33.33% (area.) oxygenates, and kerosene-like fraction by 19.87% (area.) hydrocarbons and 81.13% (area.) oxygenates.

Microfluidic technology has become a powerful tool for several applications in chemistry, physics, biology, and engineering. Benefiting from the advantages of flowing fluids in the laminar regime, droplet-based microfluidics enable the development of various delivery systems based on food-grade emulsions, such as multiple emulsions, microgels, microcapsules, solid lipid micro-particles, and giant liposomes. Besides, by manipulating fluids on a micrometer scale with low-energy demand, it is possible to control the size, shape, and dispersity of droplets generated, which makes microfluidic emulsification an excellent strategy to modulate delivery system properties depending on the entrapped compound type. Thus, this review points out the most current advances in droplet-based microfluidic processes, in which food-grade materials were successfully utilized to develop simple and complex delivery systems. In that context, we sum-marized the principles of droplet-based microfluidics, introducing the most common microde-vices geometries, manufacturing materials, and forces involved in the different droplet generation processes within the microchannels. Subsequently, the encapsulated compound type, classified as lipophilic or hydrophilic functional compounds, was used as a starting point to present current advances in delivery systems based on food-grade emulsions and assembly using microfluidic technologies. Finally, we discuss the limitations and perspectives of scale-up in droplet-based microfluidic approaches, including the challenges that have limited the transition of microfluidic processes from lab-scale to industrial-scale.

This article addresses the urbanization model in valley bottom areas in the city of São Paulo, an-alyzed in its urban planning and socio-environmental aspects, and examines the hydrological impacts triggered by its implementation. It argues that sustainable occupation of urbanized hy-drographic basins should be based on environmental criteria in order to attain a sustainable water management regime that can ensure urban and environmental resilience. In the “Introduction,” the article emphasizes that urbanization in São Paulo has neglected the natural features of river basins, promoting the channeling of watercourses, which resulted in floods and inundations. “Theoretical Basics” brings in key concepts related to the environmental approach of drainage infrastructure with gray and green-blue systems. “Methods” details our qualitative research, bibliographical analyzes, referential case studies, and cartographical analyzes (geoprocessing), focusing on a case study in the Jaguaré creek basin. “Results” includes guidelines and recom-mendations for an urbanization model adjusted to valley bottom areas, applicable to new patterns of urban occupation or to the adjustment of existing patterns. “Discussion” explores the concept of “local sustainable self-development,” and “Conclusions” highlights the importance of an inte-grated, multisectoral, and sustainable planning, adjusted to the characteristics of river basins in valley bottom areas, promoting a socially responsible urban occupation, especially in the face of climate change.

This article aimed to evaluate, using statistical tools, the generation and composition of urban solid waste (MSW) in the city of Belém, Pará, from nine urban collection sectors in the municipality, and the average nominal income of the population. Approximately 900kg of urban solid waste were col-lected from the municipality in the period from 2021 to 2022. Statistical tests were carried out on hypotheses with 5% significance in comparative evaluations, and their respective average nominal incomes. The results indicated that the organic fraction corresponds to 55.57% of the waste generated in the municipality, 14.26% is inert waste (potentially contaminating) and 0.67% is miscellaneous waste. It was observed that the waste generated by families with high purchasing power tends to contain higher percentages of recyclables, while in families with lower purchasing power the highest percentages tend to be organic. Knowledge of the generation of MSW is fundamental for the choice and dimensioning of operations and processes involved in the management chain at the municipal level. The decentralization of services offered based on solid waste management would enable greater success in serving the population.

The global textile sector, pivotal to economic development, significantly contributes to environmental degradation, prompting a shift towards sustainable raw material sources. Embracing circular economy principles, this industry is exploring the valorization of agricultural by-products. This study introduces an innovative approach to repurposing mango waste into valuable textile fibers, a byproduct of the fruit processing industry, predominantly generated during juice and jam production. The focus is on the lignocellulosic constituents of mango waste, specifically the peel, seed, and fibrous material, traditionally considered as refuse. Previous research has predominantly utilized mango peel in pectin extraction for food applications, whereas the potential of seed and fibrous content remains underexplored. This investigation endeavors to transform these fibrous by-products into high-value materials suitable for textile manufacturing. The process involved washing, drying, and comprehensive physicochemical characterization of mango fibers, emphasizing lignin quantification, revealing a composition of 12.2% lignin. An experimental design was employed to elucidate the impact of variables such as liquid-to-solid ratio, reaction duration, and sodium hydroxide concentration on lignin dissolution through alkaline hydrolysis. Optimal conditions—10% NaOH concentration, 30 mL/g liquid-to-solid ratio over six hours—achieved an 83% reduction in lignin content. The resulting fibers exhibited properties akin to conventional natural fibers, including a favorable aspect ratio indicative of their suitability for textile applications. A subsequent softening process using propylene glycol enhanced the fibers' spinability, producing a durable, textured fabric ideal for eco-conscious fashion applications, including bags, footwear, and accessories. This research demonstrates the feasibility of converting mango waste into a textile-worthy material and underscores the importance of waste revalorization in promoting sustainability within the circular economy framework.

Brazil is the world leader in pesticide consumption, and its indiscriminate use puts farmers’ health at risk. The CYP2C9 gene stands out for encoding the CYP2C9 enzyme, which metabolizes several endogenous substrates and specific xenobiotics, especially pesticides. Our goal is to study the risk of pesticide use, espe-cially the herbicide glyphosate, in the development of diseases and the association with two CYP2C9 poly-morphisms, in farmers living in the southern region of Espírito Santo state, Brazil. The allelic frequency of CYP2C9*1, CYP2C9*2 and CYP2C9*3 was determined in blood samples from individuals exposed or not to pesticides using real-time PCR. 304 blood samples were analyzed, dividing CYP2C9 genotypes into three metabolization classes: normal, intermediate, and slow. Our results show that normal metabolizers are more vulnerable to diseases such as blood pressure changes and cardiovascular and kidney problems, while in-termediate metabolizers show an association with attention deficit disorder and miscarriages, suggesting that farmers in the studied region developed symptoms correlated to the CYP2C9 genotype they have. This work is pioneering in associating specific genetic variations and health risks with pesticide exposure, em-phasizing the importance of personalized medicine and stricter regulation of pesticide use for public health and occupational safety.

This work offers a new log generalized odd log-logistic exponential regression model for analyzing weekly dengue fever cases in 2022 with a location-systematic component. To achieve this, a data set of 49 observations of dengue fever cases in the Federal District of Brazil is employed. A review of the mathematical properties of the generalized odd log-logistic exponential distribution is provided, the maximum likelihood method is used to estimate the parameters, and, through Monte Carlo simulations, the accuracy of the estimators is investigated. The model's fit is assessed using global influence metrics and residual analysis. For the time scenario studied, the proposed regression identified factors that have an impact on dengue fever cases, which may contribute to improve disease control. Finally, several interpretations are addressed, and a discussion presents results that aid in better understanding the data set and future research on different data.

Over the last decades, the increased incidence of metabolic disorders such as type 2 diabetes and obesity has motivated researchers to investigate new enzyme inhibitors. In this study, the inhibitory effects of synthetic amino acid derivatives (PPC80, PPC82, PPC84, PPC89, and PPC101) on the activity of digestive enzymes was assessed by in vitro assays. The inhibitory effect was determined by the inhibition percentage and the 50% inhibitory concentration (IC50), and the mechanism of action was investigated by Lineweaver–Burk plots. PPC80, PPC82, and PPC84 inhibited pancreatic lipase (IC50 of 1.67–10.23 x 10-1 mmol/L). The activity of pancreatic α-amylase was suppressed by PPC80, PPC82, PPC84, PPC89, and PPC101 (IC50 of 1.62–5.19 x 10-1 mmol/L). Finally, PPC84, PPC89, and PPC101 also showed a potent inhibitory effect on α-glucosidase (IC50 of 0.51–3.53 x 10-1 mmol/L). PPC80 and PPC82 followed a non-competitive inhibition mechanism against pancreatic lipase, while PPC84 acted through competitive inhibition. The inhibition of pancreatic α-amylase by the derivatives was non-competitive, as well as for PPC84, PPC89 and PPC101 against α-glucosidase. The results suggest that these synthetic amino acid derivatives have inhibitory potential against digestive enzymes and may be used as therapeutic agents to control metabolic disorders.

This study presents, for the first time, the development of fibers with favorable properties for biodegradable wound dressings made from the Ecovio® (EC) polymer blend, composed of poly(lactic acid) (PLA) and poly(butylene adipate-co-terephthalate) (PBAT), incorporated with tea tree essential oil (TTE). TTE presented antimicrobial activity against Pseudomonas aeruginosa and Staphylococcus aureus, achieving minimal inhibitory concentrations of 15 and 7.5 mg/mL, respectively. The TTE was mixed with EC in a binary chloroform and formic acid (85/15 v/v) mixture, leading to homogeneous and wettable fibers by electrospinning. The EC/TTE fibers were characterized confirming the TTE in the fibers. The tests showed that TTE (0.5, 1.0 or 1.5 mL) improved the polymer blend electrospinnability. TTE (1.5 mL or 75 w% concerning the EC) lead to homogeneous fibers with an average diameter of 278 nm. TTE (75 w%) increased the wettability of the EC fibers from 120±2° to 69±1°. Preliminary bacterial adhesion and proliferation assays demonstrated that the EC/TTE fibers have anti-adhesive activity e seems to be more toxic against P. aeruginosa compared to S. aureus after 24 hours of incubation. Compatibility tests with human blood indicated that the EC/TTE fibers accelerate blood coagulation. The EC/TTE fibers exhibit promising chemical and biological properties (in vitro) for the development of wound dressings.

In the discussion on environmental policies, the notion of eco-efficiency is often used. Eco-efficiency is defined as the delivery of products and services with competitive values, while reducing the ecological impacts and satisfying human needs. In an environment of great competitiveness in which the companies operate, the improvements in the productive process is one of the differentiating factors for guaranteeing a strong competition. Also it is essential rationalizing energy consumption and natural resources. For this it is necessary to understand the main operations and dynamics of the company. This work presents an empirical study of a Portuguese company in the industrial sector. The problematic here presented is based on the company’s growing concern to reduce the amount of scrap produced. From the literature research that was performed, a strong dependence relation between the different variables in the extrusion process was found. The main objective of this work is to model the aluminium extrusion process, with the aim of minimizing the production of scrap. For this several variables involved in the process are taking into account. Using statistical techniques, in particular multiple linear regressions, it was possible to identify the importance of the variables under study for the scrap production.

The adipose tissue is responsible for fat storage and is the major producer of exosomes. Biological content transported by the exosomes provides information, such as immunometabolic alterations. This study aimed to isolate whole exosomes from plasma and supernatant of differentiated 3T3-L1 cells using three isolation techniques. Plasma from 120 individuals categorized by body adipose tissue proportion and differentiated 3T3-L1 cells were used in this study. The exosome isolation techniques were differential centrifugation (DC), size exclusion chromatography (SEC), and a commercial kit (Invitrogen), and characterized by cryo-TEM, TEM, and western blot for the tetraspanins CD9 and CD81. In the three isolation techniques, cryo-TEM and TEM analysis showed similar quality, quantity, and morphology of exosomes; at the same time, no difference was observed between individuals categorized by proportion of body fat. According to our results, the concentration of the circulating exosomes is not different between normal and high-fat percentage individuals, but rather their composition. The SEC and kit commercial proved that compile with most of the advantages of an exosome isolation technique, nerveless we emphasize the importance of selecting the appropriate methodology depending on the specific research objectives.

This work aims to investigate systematically the tecno-economic feasibility of ther-mos-catalytic cracking process for two solid waste materials, a lipid-base material (re-sidual fat/scum from retention box of the University Restaurant of UFPA) and a lig-nin-cellulosic material Açaí seed (Euterpe oleracea. Mart). The thermo-catalytic process-es were carried out in pilot scale (THERMTEK/LEQ/UFPA/IME/RJ), and their economic feasibility analyzed. The yields of biofuels produced by fractional distillation were al-so studied. The physicochemical characteristics of the raw materials, the organic liquid product (bio-oil) and the chemical composition of kerosene, light-diesel and heavy-diesel from the lipid-base material, as well as those of kerosene and light-diesel from the Açaí seed were also determined. The economic indicators for the evaluation of the most viable cracking (pyrolysis) and distillation process of bio-oils were: a) the sim-ple payback criterion, b) discounted payback, c) net present value (NPV), d) internal rate of return (IRR), and e) index of profitability (IP). The analysis of the indicators showed the economic viability of crude palm oil (Elaeis guineensis, Jacq) and unfeasibil-ity for the palm oil neutralization. The minimum fuel selling price (MFSP) obtained is this work for the biofuels was of 1.34 US$/L) and the breakeven point obtained was of 1.28 US$/L. The sensibility analysis demonstrated that the pyrolysis and distillation yields are the most important variables to affect the minimum fuel selling price (MFSP).

Clusterin (CLU) protein is involved in various pathophysiological processes including carcinogenesis and tumor progression. In recent years, the role of the secretory isoform has been demonstrated in tumor cells, where it inhibits apoptosis and favors the acquisition of resistance to conventional treatments used to treat cancer. To determine the possible therapeutic potential of inhibiting this protein, numerous studies have been carried out in this field. In this paper, we show the existing knowledge on the inhibition of this protein in different types of cancer and discuss the importance it could have in the development of new therapies directed against this pathology.

Myalgic Encephalomyelitis, also known as Chronic Fatigue Syndrome (ME/CFS) and Long COVID are characterized by debilitating post-exertional malaise and other core symptoms related to immune dysregulation resultant from post-viral infection, including mitochondrial dysfunction, chronic neuroinflammation and gut dysbiosis. The reported associations between altered microbiota composition and cardinal symptoms of ME/CFS and Long COVID, suggesting that use of microbial preparations, such as probiotics, by restoring the homeostasis of the brain-immune-gut axis may help in the management of symptoms in both conditions. Therefore, this review aims to investigate the implications of alerted gut microbiome and assess the evidence supporting use of microbial-based preparations, including probiotics, synbiotics, postbiotics alone and/or in combination with other nutraceuticals in the management of fatigue, inflammation, as well as neuropsychiatric and gastrointestinal symptoms among patients with ME/CFS and Long COVID.

Cities are complex systems requiring urban design models that balance order and disorder. Collective creativity initiatives engage citizens in these processes, empowering bottom-up approaches that prioritize people and social well-being within urban development. This paper investigates an 'Urban Laboratory' as a case study, examining the potential of collective creativity to address urban complexity. The successful and ongoing project 'El Campo de Cebada' in Madrid, Spain, demonstrates how a community transformed a vacant lot into a vibrant social hub. The phases of this study include case selection, data collection, data analysis, and presentation of the results. This study identifies key enabling factors, including agents, management, social dynamics, infrastructure, and actions. These insights offer a methodological framework for designing future collaborative, resilient, and inclusive urban spaces, addressing the complex needs of communities within our cities.

Polyunsaturated fatty acids (PUFAs) and antioxidants are important mediators in the central nervous system (CNS). Lipid derivatives may be used to generate endocannabinoids or prostanoids derived from arachidonic acid, which attenuates excitotoxicity in quadripartite synapses with a focus in astrocytes and microglia; on the other hand, antioxidants, such as glutathione (GSH) and ascorbate, have been shown to signal through transmitter receptors and protect against acute and chronic oxidative stress, modulating the activity of different signaling pathways. Several authors have investigated the role of these nutrients in young and senescent brain, as well as in degenerative conditions such as Alzheimer’s and Parkinson's diseases. Through literature review, we aimed to highlight recent data on the role of fatty acids, antioxidants and physical activity in physiology and in molecular mechanisms of brain senescence. Data indicate the complexity and essentiality of endogenous/dietary antioxidants for maintenance of the redox status and control of neuroglial signaling under stress. Recent studies also indicate that omega-3 and -6 fatty acids act in a competitive manner to generate mediators for energy metabolism, feeding behavior, plasticity and memory mechanisms throughout aging. Finding pharmacological or dietary resources that mitigate or prevent neurodegenerative affections continues to be a great challenge and require additional efforts from researchers, clinicians and nutritionists in the field.

The ceramic sherds from approximately 20 samples of lead-glazed tableware, recovered from diverse archaeological sites, including three repurposed storage pits transformed into dumpsters within the medieval city of Santarém (13th-14th century), underwent a meticulous examination. This investigation utilized techniques such as micro-Raman, ground state diffuse reflectance absorption, and X-ray fluorescence spectroscopies, in addition to X-ray diffraction and stereomicroscopy. A parallel study was conducted on contemporaneous European ceramics (glazed sherds) sourced from archaeological sites dating back to the 13th-15th centuries in Saintonge (France), Ardenne, Zomergem, and Bruges (Belgium), as well as Surrey-Hampshire, Kingston, and Cheam (England). The colour of the ceramic bodies is predominantly white or whitish, with a few exhibiting a vivid red hue. Ceramic sherds with a light paste composition were likely crafted using kaolin clays as raw materials. Analyses of fabric, mineralogical, and elemental composition of the sherds suggest that the majority of Santarém's glazed ceramics were locally or regionally produced, potentially derived from a Pliocene kaolin-rich sand formation. However, this conclusion is not supported by the absence of discovered lead glaze kilns or workshops in Santarém for the late Middle Ages. A distinctive feature from the European workshop ceramics lies in the quartz temper content and fabric.

As is known, the construction industry has one of the highest occupational accidents incidence rates among all economic sectors. Currently, Building Information Modeling (BIM) appears as a tool that addresses occupational safety issues throughout the construction life cycle projects, avoiding hazards and risks and, consequently, increasing safety. This work investigates BIM methodology and related technologies application for building safety planning in construction and demonstrates the potential of this technology for the integrated implementation of safety measures during the design phase and the construction site management. The first step consisted of a literature review on the application of BIM in safety in the design and planning phases. Following, to show the potentialities of construction simulation, a case study based on BIM 4D to prevent falls from height was developed. With BIM 4D, it is possible to follow the construction process over time, giving the construction safety technicians’, designers, supervisors and managers the capability to analyse, in each phase, the potential risks and which safety measures should be implemented. BIM can effectively integrate safety measures from the design phase to the construction and use phase and do integrated safety planning within construction planning, leading to reliable safety management throughout the construction process.

Background: Excessive sun exposure, together with insufficient protection, is the main risk factor for the onset of Melanoma and Non Melanoma skin cancer, namely the most common cancer in fair-skinned populations across the world, and of several other skin and eye adverse health effects. Epidemiological data show the existence of scant awareness of this risk, and of high rates of sunburn among young people. The main aim of the present study is to examine sun exposure habits and protection behaviour in university students. Methods: We performed a cross-sectional questionnaire-based study to investigate sun exposure and protection practices in a group of education sciences students at a university in southern Spain. This survey provided data for a descriptive and comparative analysis, by groups and gender, of photoprotection and skin self-examination practices. The reliability and validity of the questionnaire have been analysed. Results: The questionnaire was completed by 315 students. Most of them (74.6%) have suffered at least one sunburn in the last year. The use of sunscreen or protective clothing is not frequent, and 89.5% of students do not self-examine their skin. The metric properties of the questionnaire showed high values of reliability and validity. Conclusions: The awareness of solar exposure risk in Spanish university students of Education Sciences is low, self-protection is scant, the potential exposure to dangerous levels of UV radiation is high and most students have suffered one or more sunburns in the last year. Intervention strategies should be introduced in these students to highlight the risks involved and the need of more adequate sun protection practices. Information campaigns should be conducted to address the problem so that, when these students become teachers, they have an adequate knowledge of the risk and of the benefits of a higher attention to this problem, and can translate these competences in health education.

Background. Telegram, an Industry 4.0 style Russian-born communication service, is one of the world’s most widespread communication platforms despite Putin’s censorship. The availability of channels and bots has opened as a broadcast channel for any media outlet. Objetives. We asked the following questions: Do Spanish media outlets use Telegram channels? Which media outlets? Are they verified? What is their volume of subscribers? Can this information be used to rank media outlets? We identified many media channels and numerous variables were collected from each one. Results and conclusions. Forty-two Spanish media outlets have Telegram channels, 26 of which are ranked in the directory. Less than half of these channels are verified by the platform, and only three are linked to their website. This lack of verification could lead to the proliferation of fake channels. We created a ranking, and the top-10 includes two foreign, six national, and two regional media outlets.

The practical application of a multi-objective optimization strategy based on evolutionary algorithms was proposed to optimize the plastics thermoforming process. For that purpose, the various steps of the process were considered individually and the optimization strategy was applied to the determination of the final part thickness distribution with the aim of demonstrating the validity of the methodology proposed. The preliminary results obtained considering three different theoretical initial sheet shapes indicates clearly that the methodology proposed is valid, as it provides solutions with physical meaning and with a great potential to be applied in real practice.

The long-term laboratory aspects of the effects of COVID-19 on liver function are still not well understood. Therefore, this study aimed to evaluate the hepatic clinical-laboratory profile of patients with up to 20 months of long-term COVID-19. A total of 243 patients of both sexes aged 18 years or older hospitalised in the acute phase of COVID-19 were included in this study. Liver function analysis was performed. Changes were identified in the mean levels of alanine aminotransferase (ALT), aspartate aminotransferase (AST), lactate dehydrogenase (LDH), gamma-glutamyl transferase (GGT), and ferritin. Inflammatory markers such as ferritin > 300 U/L were observed in the group that presented more changes in liver function markers (ALT, AST, and GGT). Age ≥ 60 years, male sex, AST > 25 U/L, and GGT ≥ 50 or 32 U/L were associated with ALT > 29 U/L. There was a correlation between ALT and AST, LDH, GGT, and ferritin. Our findings suggest that ALT and AST levels may be elevated in patients with long-term COVID, especially in those hospitalised in the acute phase. In addition, ALT > 29 U/L was associated with other markers of liver injury, such as LDH, GGT, and ferritin.

Recent discoveries have shown that enteric glial cells play an important role in different neurodegenerative disorders such as Parkinson's disease (PD), which is characterized by motor dysfunctions caused by progressive loss of dopaminergic neurons in the substance nigra pars compacta and non-motor symptoms including gastrointestinal dysfunction. In this study we observed the modulatory effects of the flavonoid rutin on enteric glia in a PD animal model. Adult male Wistar rats were submitted to stereotaxic injection with 6-hydroxydopamine or saline, treated or not with rutin (10 mg/Kg) for 14 days. Intestinal segments (ileum and colon) were collected to analyze tissue reactivity and immunohistochemistry for neurons (HUc/d) and enteric glial cells (S100b) in the myoenteric plexuses. Behavioral tests demonstrated that treatment with rutin im-proved the motor capacity of parkinsonian animals, and also improved intestinal transit without interfering with the cell population; rutin treatment modulated reactivity of the ileal musculature by muscarinic activation, reducing relaxation through the signaling pathway of nitric oxide donors, and increasing the longitudinal contractility of the colon musculature in parkinsonian animals. Rutin demonstrated modulatory activities on the enteric nervous system, bringing relevant answers about the effect of the flavonoid in this system and po-tential application for PD adjuvant treatment.

Celiac disease (CD) is an immune-mediated gluten-induced enteropathy that affects predisposed individuals of all ages. Many patients with CD do not report gastrointestinal symptoms making it difficult to reach an early diagnosis. On the other hand, CD is related to a wide spectrum of extra-intestinal manifestations, being dermatitis herpetiformis (DH) the best characterized. These associated conditions may be the clue for reaching the diagnosis of CD. Over the last years, there have been multiple reports of the association between CD and several cutaneous manifestations that may improve with a gluten-free diet (GFD). The presence of some of these skin diseases, even in absence of gastrointestinal symptoms, should give rise to an appropriate screening for CD. The aim of this paper is to describe the different cutaneous manifestations that have been associated to CD and the possible mechanisms involved.

We consider open non-twist Hamiltonian systems represented by an area-preserving two-dimensional map describing incompressible planar flows in the reference frame of a propagating wave, and possessing exits through which map orbits can escape. The corresponding escape basins have a fractal nature that can be revealed by the so-called basin entropy, a novel concept developed to quantify final-state uncertainty in dynamical systems. Since the map considered violates locally the twist condition, there is a shearless barrier that prevents global chaotic transport. In this paper we show that it is possible to determine the shearless barrier breakup by considering the variation of the escape basin entropy with a tunable parameter.

Daptomycin is one of the last therapeutic resources for multidrug-resistant gram- positive bacteria. Despite its structural similarities with glycopeptides, its mechanisms of action and resistance are different, and in some respects are not completely understood. Mutations in several genes have been associated to daptomycin resistance, especially in mprF, walkR, rpoB and rpoC, but their role and importance remain to be elucidated. We have studied mutations in 11 genes, which have been previously associated to daptomycin non- susceptibility, in 9 daptomycin non-susceptible Staphylococcus aureus clinical isolates (daptomycin MIC: > 1mg/L). Susceptibility to daptomycin, vancomycin, linezolid, oxacillin, telavancin and dalbavancin were studied. walkR, agrA, cls1, cls2, fakA, pnpA, clpP, prs, rpoB, rpoC and mprF were amplified by PCR and sequenced. The sequences were compared with the S. aureus ATCC 25923 complete genome (GenBank gi: 685631213) by using BLAST® software. We did not find any changes in walkR, pnpA, prs and clpP. All isolates excepting isolate 5 showed a high number of significant mutations (between 13 and 25 amino acid changes) in mprF. Most isolates also showed mutations in rpo genes, cls genes and fakA. Daptomycin non-susceptibility in S. aureus clinical isolates seems to be reached through different mutations combinations when compared to S. aureus ATCC 25293. Especially mprF and cls1 showed a very high polymorphism in most isolates. Meanwhile, one isolate, St5, showed only single mutation in mprF (P314T).

The demand for sustainable cosmetics leads to the search for natural and biotechnology ingredients. The present study reports the development of multifunctional lip moisturizer containing levan (LEV) from Bacillus subtilis natto, sophorolipids (SOP) from Starmerella bombicola and Citrus paradisi (OCP) essential oil , using simplex-centroid experimental design. The formulations were evaluated physicochemically, pharmacotechnically and by DPPH assay. The optimized formulation was selected through Response Surface Method and the evaluation of its efficiency in lip hydration was carried out using bioimpedance method and sensory analysis. The formulations showed pH compatible with the lip region and remained stable after centrifuge test and thermal stress in preliminary stability. Spreadability varied between 415.3 and 1217.1 mm2, moisture retention was above 95%, and antioxidant capacity was around 50% for all formulations. The optimized formulation, containing 0.4% LEV and 0.8% SOF, helped to maintain the lip hydration already shown by the participants; 85% of them reported improvement in this aspect. The incorporation of these actives is innovative and helps in the development of future works, through the use of a new non-invasive and low-cost technique, not previously described in other studies, in association with relevant sensory analyzes in the field of cosmetology.

The epidemic transmission of Zika virus (ZIKV) in Brazil has been identified as a cause of microcephaly and other neurological malformations in babies of ZIKV-infected women. This study provides a descriptive analysis, since the onset of symptoms to the delivery, of a cohort who were registered as having ZIKV infection in pregnancy, from November 2015 to December 2016. Suspected cases were registered at a referral center for infectious and tropical diseases in Manaus, in the Brazilian Amazonian region. A total of 834 women with suspected ZIKV in pregnancy were included, of whom 91.4% had confirmed pregnancy. Reverse-transcriptase polymerase chain reaction (RT-PCR) confirmed ZIKV infection in 42.2% of the cohort. In 35.2% of the cohort, ZIKV was the sole infection identified. Severe adverse pregnancy outcomes (abortion, stillbirth, or microcephaly) were observed in both RT-PCR ZIKV-positive (4.96%) and ZIKV-negative (2.15%) cases. Women with suspected ZIKV infection were much more likely to have adverse pregnancy outcomes if they were symptomatic during the first trimester of pregnancy (odds ratio 10.5; 95% confidence interval 4.0–27.0; p<0.001). Among pregnant women with suspected ZIKV infection, the occurrence of symptoms in the first trimester is associated with an especially high risk of severe adverse pregnancy outcomes.

Acute lymphoblastic leukaemia is currently treated with bacterial L-Asparaginase; however, its side effects bring up the special need for improved and efficient novel enzymes development. Previously, we obtained low anti-asparaginase antibody production and high serum enzyme half-life in mice with the P40S/S206C mutant; however, its specific activity was significantly reduced. Thus, our aim was to test single mutants, S206C and P40S, for in vitro and in vivo assays. Our results showed that the drop in specific activity was caused by P40S substitution. Besides, our single mutants were highly stable in biological environment simulation, unlike double mutant P40S/S206C. The in vitro cell viability assay demonstrated that mutant enzymes have higher cytotoxic effect than WT on T-cells derived ALL and on some solid cancer cell lines. The in vivo assays were performed in mice to identify toxicological effects, to evoke immunological response and to study the enzymes pharmacokinetics. From these tests, none of the enzymes was toxic; however, S206C evoked lower physiological changes and immune responses. In relation to pharmacokinetic profile, S206C has two-fold higher activity than WT and P40S two hours after injection. In conclusion, we present bioengineered E. coli asparaginases with high specific enzyme activity and lesser side effects.

Thermal comfort is extremely important in architecture, especially in environments with more people spending longer on studies or intellectual activities. This research describes a case study to investigate university buildings' energy and thermal performance as a part of the ANEEL program. Due to this importance, and the need to save energy in Brazilian public buildings, the ANEEL-the Brazilian Energy Electricity Regulatory Agency, launched 2016 a national program focusing on energy efficiency in public universities around the country. University offices and classrooms require high intellectual effort; thus, environmental comfort is critical for maintaining its users' physical and mental health. This study included a pre-diagnosis of the performance of the envelope, lighting, and air conditioning systems and a survey about the quality of the environments from the users' point of view. The Prescriptive Method of the Brazilian Labeling Program (PBE) for Commercial, Service, and Public Buildings (RTQ-C) assessed the building performance. Statistical analysis was applied to correlate the quality and thermal preference of the users from the PMV/PPD. The results showed a high rate of thermal discomfort in both environments of the studies, even when using air conditioning.

In this study a material based on Polyethylene (PE) and Microcrystalline Cellulose (MC) was developed as a breathable packaging film. Surface functionalization of MC with 3 aminopropyltriethoxysilane (APTES) shows to be an efficient alternative to tailor their properties and increase opportunities for the application of MC on the reinforcement of polymers such polyethylene (PE). Functionalization of MC with mentioned silane derivative was achieved using a green method and later used on the development of composites with PE in three percentages (1, 3 and 5%). All the materials were prepared by melt blending and characterized, in terms of structural properties (ATR-FTIR and FTIR in transmittance, EDX, SEM), thermal properties (DSC and TGA), thermomechanical properties (DMA), contact angle measurements and permeability to oxygen and water vapor. The materials demonstrated to have potential to be used as breathable film packaging of fresh products.

Visceral leishmaniasis (VL) results from infection by the protozoa Leishmania infantum and L. donovani. HIV-coinfected patients may have a relapsing course of VL, even after secondary prophylaxis with amphotericin B. This study investigated whether host factors would explain the relapses. First, susceptibility to amphotericin B of L. infantum isolates was evaluated in vitro. Then, clinical data and the lipid profile of patients with relapsing and non-relapsing VL were assessed. Susceptibility to amphotericin B was similar between the isolates. CD4+ lymphocytes were reduced in both patients in the first episode and with relapsing VL. Still, the strongest blood cell associated with relapses was low total lymphocyte counts. Total plasma cholesterol, high-density lipoprotein, low-density lipoprotein, and, uniquely, triglycerides of the six individuals in the first episode and 23 with relapsing VL were lower in relapsing patients than those in the first episode. Deceased patients had extremely low, low-density lipoprotein. After CD4+ decrease, lymphocyte CD8+ reduction seem to be the final stage of the immunological failure. The lower lipid concentrations appear to be secondary to the depletion of fat stores by inflammation-induced cachexia provoked by the co-occurrence of both diseases, which can finally lead to death.