The alternating stress caused by periodic high-pressure injection and extraction in gas storage can potentially induce fault slippage, compromising the sealing integrity of faults within these facil-ities. Understanding the mechanical behavior of faults under alternating stress is crucial for en-suring the long-term stability and safety of gas storage operations. To explore the impact of fault dip angle and fault gouge strength on fault slip characteristics, fault samples were prepared with uniaxial compressive strengths of 20.1, 30.2, 42.4, and 51.4 MPa at two distinct dip angles. Triaxial compression experiments were conducted under alternating stress conditions corresponding to operational pressures at a specific gas storage in China. Results indicate that faults with dip angles of 30° and 45° tend to fail at their weakest points. Increasing strength of fault gouge shifts failure mechanisms from interfacial failure between gouge and surrounding rock towards internal gouge failure, often accompanied by shear failure across sections, resulting in characteristic "X"-shaped conjugate shear failures. The decrease in the ratio of bedrock strength to fault gouge strength elucidates the observed phenomena of initial reduction followed by increased fault deformation. Transition points for faults with 30° and 45° dips occur around the strength ratios of 1.7/1 and 1.2/1, respectively. Fault damage exhibits a negative correlation with fault gouge strength and a positive correlation with fault dip angle. Samples with higher strength fault gouge at a 30° dip angle generally incur less damage compared to those with lower strength fault gouge at a 45° dip angle. Moreover, higher maximum static friction coefficients denote greater fault resistance to slipping, with 30° faults consistently demonstrating superior resistance compared to 45° faults. Additionally, higher strength fault gouge consistently enhances slip resistance under identical dip angles.

A Partial discharge (PD) occurrence in high-voltage (HV) and medium-voltage (MV) power assets is a warning sign of insulation system degradation or defective manufacturing/assembly, that may cause catastrophic damage and eventually lead to the breakdown of the power equipment. Ultra-high frequency (UHF) PD measurement technology has extensively been used to monitor the insulation health of the HV or MV equipment due to its high immunity against ambient noise and conducted disturbances. This paper presents experimental validation of a new design of a UHF planar rectangular microstrip antenna that can be used for PD monitoring of HV and/or MV power equipment, such as power transformers. The designed planar rectangular microstrip antenna has a compact size of 80mmx70mmx1.6mm. Laboratory experiments were performed to validate the antenna sensitivity to PD activity caused by insulation defects created inside an oil-filled transformer tank model. PD measurement results confirm that the proposed rectangular microstrip antenna has high sensitivity and high signal-to-noise ratio (SNR), thanks to its capability to suppress external noise disturbances, especially during online PD monitoring. Thus, the proposed UHF antenna seems to be a promising and alternative PD sensor that can be employed in UHF PD monitoring systems of HV or MV power equipment.

In eastern part of Ethiopia groundnut is very commonly intercropped with sorghum. Even though intercropping of sorghum with groundnut is practiced in the eastern part of Ethiopia the population density at what ratio should not be known. Therefore determining the population ratio is found to be crucial to draw management options. The study was conducted at two locations at Fadis (on station) and Babile (sub- station). Sorghum variety (Teshale) and groundnut (Fetene) were used as planting materials. All agronomic data were collected and analyzed by using GenStat software. Significant different were obtained among the treatments. The research result showed that, there were significance difference for both sorghum and ground nut yield per hectare in the years (2014 and 2015) among treatments. The result over time(in 2014 and 2015) at Fadis and Erer showed that the highest sorghum and groundnut yield per hectare were obtained/harvested from the intra row spacing of 25cmx20cm and 30cmx20cm intercropping sorghum with ground nut system with (1.27 and 1.31) respectively. The highest LER (1.31) and highest GMV (10218.00 ETBr/ha) were obtained from the intercropping of 30cmx20cm (Sorghum & groundnut). Clearly showed that, with intercropping of sorghum and Groundnut, it is possible to produce additional yield of sorghum without significant reduction in groundnut yield. As a result of this, the intra spacing of the main crop (sorghum) 25cm and 30cm and for the subsidiary crop (groundnut) 20cm was recommended for further production in the study areas of eastern Harerghe zone and similar agro-ecologies.

The calculation of the release of liquid hazardous chemicals storage tanks is an important part of the quantitative risk assessment of accidents. This paper mainly establishes a continuous real–time release model based on the instantaneous mass flow Q_m model. Meanwhile, the software function module was analyzed, and programming software was developed using C# language for model solving. A series of experiments for repeated leakage tests was designed and the discharges through three small holes with different heights for 200 s were observed. The results show that the continuous real–time leakage model is effective, and the deviation between theoretical and experimental release amounts are within a reasonable range. The higher the liquid level above the leak hole is, and the smaller the height of the leak hole from the ground is, the greater the flow rate at the leak orifice is and the smaller discharge rate change is. Therefore, the deviation between the theoretical release amount M_t and the experimental average release amount Ma is greater while the height of the leak hole from the ground is smaller, which indicates that the smaller the distance from the leak orifice to the ground, the greater the influence of the empirical discharge coefficient C₀ on the release amount M.

Accurate assessment of shale gas reserves hinges on a detailed characterization of gas and water distribution within shale reservoirs. Despite its importance, the nanoscale behavior of water and methane in deep shale formations, especially under elevated temperatures and pressures, remains poorly understood. This study proposes a novel molecular modeling approach to represent the complex nanocomposite porous media found in deep shale matrices. Leveraging quantitative data from experimental analyses of shale pore composition, we developed a molecular model that accurately reflects the intricate pore-slit structure within a composite of kerogen and illite, common constituents of shale. Employing a hybrid grand canonical Monte Carlo and molecular dynamics simulation technique, we investigated the micro-scale distribution and preferential adsorption sites of water and methane within the shale matrix. Our research further elucidates the impact of water on the pore structure of shale and delineates the co-occurrence patterns of water and methane. The simulations reveal that water and methane share similar adsorption preferences on kerogen surfaces, while methane does not exhibit specific adsorption preferences on water-bearing illite. We also find that the presence of water significantly alters the illite pore space, leading to a reduction in larger pore volumes and a concomitant increase in smaller pores. The decrease in methane content with increasing water content is more pronounced in the shrinkage cracks compared to the kerogen matrix pores and is particularly notable in the macropores of illite. The findings underscore the differential sensitivity of methane content to water levels across various shale pore types. These insights contribute to a deeper theoretical understanding of gas and water distribution mechanisms in deep shale reservoirs, offering valuable support for the evaluation of deep shale gas resource potential.

: This study focuses on optimizing chlorophyll extraction techniques and strategically placing leaf disks to enhance chlorophyll concentration in sesame (Sesamum indicum L.) leaves. Thirty sesame genotypes, categorized into light green (LG), middle green (MG), and deep green (DG) pigment groups based on leaf coloration, were selected from a larger pool of field-grown accessions. The investigation involved determining optimal SPAD value index measurements, quantifying pigment concentrations, exploring extraction solvents, and selecting suitable leaf disk positions. Significant variations in chlorophyll content were observed across genotypes, greenness categories, and leaf disk positions. The categorization of genotypes into DG, MG, and LG groups revealed a correlation between leaf appearance and chlorophyll content. The study highlighted a consistent relationship between carotenoids and chlorophyll, indicating their role in adaptation to warm environments. Examination of leaf disk positions revealed a significant chlorophyll gradient along the leaf blade, emphasizing the need for standardized protocols. Chlorophyll extraction experiments identified DMSO and 96% ethanol, particularly the later incubated for 10 minutes at 85°C, as effective choices. This recommendation considers factors like cost-effectiveness, time efficiency, safety, and environmental regulations, ensuring consistent and simplified extraction processes. For higher chlorophyll extraction, focusing on leaf tips and the 75% position along the sesame leaf blade is suggested, consistently yielding higher chlorophyll content. Our findings therefore, underscores insightful knowledge on chlorophyll gradients and encouraging for standardized protocols, that enabling researchers to refine experimental designs for precise and comparable chlorophyll measurements. Recommended solvent choices ensure reliable outcomes in plant physiology, ecology, and environmental studies.

Carbon dioxide (CO2)miscible fracturing huff and puff technology plays a pivotal role in enhancing the recovery rate of crude oil, particularly in reservoirs with challenging physical properties, strong water sensitivity, high injection pressure, and complex water injection dynamics. In this study, the oil-increasing mechanism and huff and puff effect of CO2 miscible fracturing fluid are investigated through a comprehensive experimental approach. Specifically, experiments on PVT gas injection expansion, minimum miscible pressure, and CO2 miscible fracturing huff and puff are conducted on the G fault block reservoir in J Oilfield. The findings demonstrate that injecting CO2 into reservoirs leads to oil volume expansion, viscosity reduction, and saturation pressure increase. Additionally, the inclusion of solubilizers and viscosity reducers further enhances the efficiency of crude oil extraction. Solubilizers not only improve oil recovery but also reduce the minimum miscible pressure required for effective CO2 dispersion. Furthermore, the shut-in time, permeability, and huff and puff method all have considerable impacts on huff and puff recovery rate. This study offers valuable technical insights, supporting the application of CO2 miscible fracturing huff and puff technology to enhance oil recovery in low-permeability reservoirs.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

Superior fiber quality is one of the most important objectives in cotton breeding. To detect the genetic basis underlying fiber quality, an F2 population containing 413 plants was constructed by crossing Jifeng 914 and Jifeng 173, both of which have superior fiber quality, with Jifeng 173 being better. Five fiber quality traits were investigated in the F2, F2:3, F2:4, and F2:5 populations. Quantitative trait loci (QTL) mapping was conducted based on a high-density genetic map containing 11,488 single nucleotide polymorphisms (SNPs) and spanning 4,202.12 cM in length. Transgressive segregation patterns and complex correlations in the five tested traits were observed. A total of 108 QTLs were found, including 27 for fiber length (FL), 16 for fiber strength (FS), 24 for micronaire (MC), 17 for fiber uniformity (FU), and 24 for fiber elongation rate (FE). Chromosome A7 contained 12 QTL, ranking the first. No QTL was found on chromosome D1 and D11. Each QTL contributed 1.98%–21.45% to the phenotypic variation (PV), including 13 major effect QTLs that contributed more than 10% toward PV. Two QTLs could be repeatedly detected in three populations, including qFL-D3-2 in F2, F2:4, and F2:5 with 9.18%–21.45% of PV, qFS-A11-1 in F2:3, F2:4 and F2:5 with 6.05%–10.41% of PV. Another seven stable QTLs could be detected in two populations, including four major effect QTLs: qFL-A12-3, qFS-D10-2, qMC-D6-2, and qMC-D8-1. Fourteen QTL-overlapping regions were found, which might explain the complex correlations among the five phenotypic traits. Four regions on chromosome A11, D3, D6, and D10 covered by both stable and major effect QTLs are promising for further fine mapping. The genomic regions of the two QTLs detected in three populations and the four major effect QTLs contain 810 genes. Gene functional analysis revealed that the annotated genes are mainly involved in protein binding and metabolic pathways. Fifteen candidate genes in the qFL-D3-2 region are highly expressed in fiber or ovules during fiber initiation, elongation, secondary cell wall thickening, or maturation stages. qRT-PCR revealed that Ghir_D03G005440.1 and Ghir_D03G011310.1 may play a role in promoting fiber initiation, Ghir_D03G006470.1 may be beneficial for promoting fiber elongation. This study provides more information for revealing the molecular genetic basis underlying cotton fiber quality.

This study aims to investigate the interfacial tension, emulsion stability, and the impact on oil displacement effectiveness of mixed systems containing nonionic surfactants and amphoteric surfactants at different ratios. To achieve this, three different emulsion stability formulations were prepared by mixing betaine and nonionic surfactants in ratios of 1:1, 3:2, and 3:1 respectively. By adjusting the proportions of betaine and nonionic surfactants, variations in interfacial tension and emulsion formation among the three mixed systems were studied to analyze the mechanism of interaction between betaine and nonionic surfactants and evaluate their effects on crude oil displacement and enhanced oil recovery in reservoirs. Subsequently, microscopic and macroscopic oil displacement experiments were conducted on the three mixed systems, along with experiments on emulsion flow resistance. The aim was to verify the oil displacement effectiveness of different mixed systems and further understand their potential applications in reservoirs. By comprehensively analyzing the experimental results, optimal ratios and conditions for the mixed systems were determined. The experimental results indicate that the emulsification system formed by mixing betaine and nonionic surfactants at a ratio of 3:1 achieves molecular synergies through electrostatic interactions and mixed adsorption with betaine, resulting in a compact arrangement of interface membranes and demonstrating a synergistic effect in reducing interfacial tension to an ultra-low value of 10 -4 mN/m. Additionally, as the proportion of betaine surfactant increases, the viscosity of the aqueous phase liquid film increases, the rate of thinning of the liquid film slows down, the rate of water release slows down, and the stability of the emulsion increases. Microscopic oil displacement experiments verified that the three mixed systems increase oil washing efficiency through low interfacial tension and emulsification stripping action, thereby increasing the oil displacement mechanism's coefficient. Emulsion flow resistance experiments demonstrated that as the proportion of betaine surfactant increases, the system exhibits better plugging ability. However, macroscopic oil displacement experiments revealed differences in compatibility between different emulsion stability solutions and rocks with different permeabilities. The mixed system of betaine and nonionic surfactants at a ratio of 3:1 exhibits the best emulsification plugging ability in rocks with a permeability of 109mD, while the 1:1 mixed system performs best in rocks with a permeability of 12mD. This holds significant theoretical and practical significance for reservoir development and enhanced production.

Asphaltene-resin-paraffin deposition (ARPD) is a complicated and prevalent issue in oil and gas industry, impacting the efficiency, integrity of petroleum extraction, production, transportation and processing systems. Considering all witnessed ARPD problems in Azerbaijan oil fields, this paper proposed a chemical method and optimized the type and the concentration of chemical inhibitors. And then the effect of selected chemical reagent on inhibiting the ARPD amount and thus en-hancing oil recovery was detected by reservoir simulation during both waterflooding and CO2 flooding production. Three new chemical compounds (namely, Chemical-A, Chemical-B and Chemical-C) were examined in laboratory conditions and their impact on rheological properties of high-paraffin oilfield samples of Azerbaijan (X, Y and Z) were investigated. Experimental results show that Chemical-C with concentration of 600 g/t has the best efficiency for alleviating the problems. After adding Chemical-C to the crude oil, the freezing point of oil is decreased from 12 °C to (-4) °C, ARPD amount is declined from 0.185 to 0.016 g and oil effective viscosity is reduced from 16.2 mPa·s to 3.1 mPa·s. It is determined that for water and CO2 flooding, higher injection pressure resulted in reduced asphaltene precipitation. Adding selected ARPD inhibitor, the oil recovery for waterflooding can increase from 52% to 62%, while it can rise from 55% to 68% for CO2 flooding.

This paper presents an acoustic emission (AE) detection method for refined oil storage tanks, enabling online detection of corrosion points and microleakage in the tank floor. The method utilizes an explosion-proof acoustic emission instrument to detect the floor of a refined oil storage tank. By calculating the time difference between the defective acoustic signal and the speed of acoustic wave transmission, a mathematical model is constructed to analyze the detected signals. A technical scheme for acoustic emission detection in storage tanks is designed, and the instru-ment is used to carry out acoustic emission testing on the product oil storage tank floor. Based on these test results, location analysis of acoustic emission sources is conducted on the bottom plate of the tank, evaluating its corrosion condition accurately. The consistency between the evaluation and subsequent open tank tests confirms that using acoustic emission technology effectively captures corrosion signals from product oil storage tank bottoms. Consequently, it significantly improves inspection efficiency by avoiding unnecessary tank-opening operations. Combining this method with open tank inspection operations such as the leakage magnetic method, one can fully grasp the status of the refined oil storage tanks.

Objectives. The aim of the study is to identify relevant research topics based on pooled bibliometric data of International Journal of Hydrogen Energy publications from 2022-2024, collected from The Lens and ScienceDirect platforms. Data source. Bibliometric records of International Journal of Hydrogen Energy articles published in 2022-2024 from The Lens and ScienceDirect platforms were used. Programs and utilities used. VOSviewer, Scimago Graphica, Inkscape, FP-growth utility. Results. The study showed the feasibility of merging bibliometric records from the open platforms ScienceDirect and The Lens, which complement each other. The 'Fields of Study' data of The Lens can be rationally interpreted as system keywords similar to Scopus Index Keywords. The possibility of using 'Fields of Study' data in a method similar to bibliographic coupling is shown. The practicality of using an Alluvial diagram to show the co-occurrence of the four terms was demonstrated. The study also emphasizes the advisability of joint use of VOSviewer and Scimago Graphica programs for complex visualization of bibliometric analysis results. The study identified two dominant publication topics in International Journal of Hydrogen Energy for 2022-2024, which can be described in terms of: 'Catalysis, Hydrogen, Physical_chemistry, Chemical_engineering, Nanotechnology, Electrochemistry, Organic_chemistry, Materials_science' and 'Electrical_engineering, Hydrogen_production, Renewable_energy, Environmental_science, Hydrogen_economy, Hydrogen, Engineering'.

Objectives. The aim of this study was to demonstrate the ability to visualize the results of the Scilit platform's bibliometric data analysis on the topic "AI & Machine Learning" to identify publications reflecting specific issues of the topic. Data source. Bibliometric records exported from the Scilit platform on the topic "AI & Machine Learning" for the years 2021–2023 were used. For each year, 6,000 records were downloaded in CSV and RIS format. Programs and utilities used. VOSviewer, Scimago Graphica, Inkscape, FP-growth utility, GSDMM algorithm. Used services: Elicit, QuillBot, Litmaps. Results. It has been shown that bibliometric data from the open access abstract database Scilit can serve as a quality alternative to subscription-only databases. Data exported from the Scilit platform require preprocessing to make them available in a format that can be processed by programs such as VOSviewer and Scimago Graphica. The use of GSDMM and FP-growth algorithms is effective for structuring bibliometric data for further visualization. The Scimago Graphica software provides wide possibilities for building compound diagrams, in particular, for representing the network of keywords in such important coordinates for bibliometric analysis as average year of publication and average normalized citation, as well as for building an alluvial diagram of co-occurrence of more than two keywords. The possibility of using such services as elicit.com, quillbot.com and app.litmaps.com to accelerate the selection of publications on the topic under study is shown.

Background. Keyword co-occurrence analysis is a crucial tool for comprehending research trends, identifying relevant studies, and gaining insight into the connections between various concepts and topics. Objective. This study focuses on analyzing the co-occurrence of keywords using FP-growth algorithm and direct search methods. Materials and methods. The methodology involved extracting bibliometric data of Energies journal for 2023-2024 from MDPI publisher platform, keyword lemmatization and keyword co-occurrence estimation. Clustering and visualization were performed using Multidendrograms and Scimago Graphica software. Results. The results showed that the FP-growth algorithm can achieve a close match with the direct search results, which facilitates data preparation for clustering. In addition, finding the co-occurrence of three or more keywords significantly reduced the number of possible combinations, which allowed the identification of specific research topics. Conclusions. This study highlights the usefulness of the FP-growth algorithm in keyword analysis and provides insights into ways to refine search queries to abstract databases for the purpose of designing and writing literature and systematic reviews.

Relevance of the subject. Keyword selection is critical to finding relevant literature and requires justification for querying abstract databases and other sources to ensure accuracy and completeness. The topic of Energy Systems is of great importance due to the introduction of renewable energy sources, modern control methods, and complex energy systems during the energy transition. The aim of this study. The goal of this paper was to identify keywords that would be useful to subject matter experts when collecting literature on a particular topic, based on entries in the IEEE Terms field. Data. Bibliometric data were exported from the IEEE Xplore platform in the following order: for 2019-2023, 2000 records sorted by relevance, for 2024, 1680 records current as of April 11, 2024. Analytical methods applied and software used. VOSviewer, Scimago Graphica implementing the Clauset-Newman-Moore algorithm and agglomerative hierarchical clustering method implemented in Multidendrograms. Results. The main issues of the Energy Systems topic are presented in tabular and graphical formats. The fpgrowth utility offers flexible data preparation options, which makes it worthwhile to conduct a separate study to analyze the score of co-occurrence terms given by its algorithm.

Purpose of publication: - Preparation of bibliometric data exported from the Scilit platform on energy efficiency and conservation for further analysis to identify relevant research topics. - To identify potential issues in the processing of data exported from the Scilit platform. - Providing colleagues with the opportunity to use the prepared data and examples of their analysis for independent research on topical issues of energy efficiency and energy conservation using materials provided by the Scilit platform. Research Materials: Files in CSV and RIS formats exported from Scilit for the query "energy conservation OR efficiency" in Common Fields [Title, Abstract, Keyword], using filters: Content Type → Journal Article; Year→2021-2023; Subject → Industrial Engineering (29.8K), Energy and Fuel Technology (9.8K), Manufacturing Engineering (9.2K). A total of 30K records sorted by their relevance (10K for each year) were exported. Data are current as of 14-03-2024. Methods: Preprocessing of title, annotation, and keyword field texts using lemmatization dictionaries collected on GitHub, removal of keywords taken from GATE and spaCy, and "manual" editing. Using VOSviewer to analyze publication topics by clustering keywords based on their co-occurrence. Using Scimago Graphica to build bubble diagrams.Application of the GSDMM algorithm for clustering bibliometric records by title and annotation texts. Creation of a dictionary for this algorithm using the keyword field.Use of the Carrot2 demo version and the NMF algorithm for a more detailed analysis of the topics of the record clusters obtained from GSDMM. Results: are presented in the form of initial and interim tables and graphs obtained in the course of this study. The full tables are provided as references to the attached materials. Supplementary material for this preprint on figshare: Chigarev, Boris (2024). Supplementary material for preprint "Analyzing the Possibilities of Using the Scilit Platform to Identify Current Energy Efficiency and Conservation Issues". figshare. Dataset. https://doi.org/10.6084/m9.figshare.25574058.v1

The aim of this study was to investigate the physicochemical characterization and biological activities of chitosan (CH) based composite films with the incorporation of chestnut flower essential oil (CFEO). The composite films were prepared by casting method and characterized in terms of structural, morphological and mechanical properties via FT-IR, XRD, UV, SEM and TGA. The results proved the significantly increased water vapor permeability (WVP), heat resistance, antibacterial and antioxidant capabilities of CH-CFEO films. The incorporation of CH and CFEO enhanced the UV blocking, which made the film shield almost all UV light. Films with the tensile strength of 6.37 ± 0.41 MPa and elongation at break of 22.57 ± 0.35% were got with 6 mg mL-1 CFEO. Subsequently, the fruit preservation experiments also confirmed that the composite films could effectively extend the shelf life of bananas through their excellent water vapor and oxygen barrier. These desirable performances enable our newly developed composite films to be a remarkable packaging material to solve the fresh fruit preservation dilemma.

With the offshore oil-gas fields entering decline phase, high-efficiency separation of oil-gas-water mixtures becomes a significant challenge. As essential equipment for separation, the three-phase separators play a key role in Offshore Oil-Gas production. However, level control is critical in the operation of three-phase gravity separators on offshore facilities, as it directly affects the efficacy and safety of the separation process. This paper introduces an advanced deep deterministic policy gradient with adaptive learning rate weights (ALRW-DDPG) control algorithm, which improves the convergence and stability of the conventional DDPG algorithm. An adaptive learning rate weight function is meticulously designed, and an ALRW-DDPG algorithm network is constructed for simulating three-phase separator liquid level control. The effectiveness of the ALRW-DDPG algorithm is subsequently validated through simulation experiments. The results show that the ALRW-DDPG algorithm achieves a 15.38% improvement in convergence rate compared to the traditional DDPG algorithm, and the control error is significantly smaller than that of PID and DDPG algorithms.

The accurate state of health (SOH) estimation of lithium-ion batteries (LIBs) during operation is crucial to ensure optimal performance, prolonging battery life and preventing unexpected failure or safety hazards. This work presents a storage and performance optimised deep learning approach to predict the capacity based SOH of LIBs using raw sensor data from partial charging curves under constant current condition. The proposed model is based on a combination of a 1-dimensional convolutional and long-short term memory neural network and processes time, voltage and incremental capacity of partial charging curves as time series. The model is cross-validated on different aging scenarios reaching an overall MAE = 0.418% and RMSE = 0.531%, promising an accurate SOH estimation of LIBs under varying usage and environmental conditions in a real world application.

Accurate evaluation of thermo-fluid dynamic characteristics in tank are critically important for designing liquid hydrogen tank of small-scale hydrogen liquefier to minimize heat in-leak into the liquid and ullage. Due to the huge cost, most future liquid hydrogen storage tank designs will have to rely on predictive computational models for storage tank pressurization and heat-leak minimization. Thus, reliable on predictive numerical models to aid design process of tank design have been required. Therefore, in this study, in order to improve the storage efficiency of the small-scale hydrogen liquefier, a three-dimensional CFD model that can predict the boil-off rate and the thermo-fluid characteristics due to heat penetration has been developed. The prediction performance and accuracy of the CFD model is validated on the basis of the comparisons between its results and previous experimental data and a good agreement is obtained. To evaluate insulation performance of polyurethane foam according to thickness, the pressure change and thermo-fluid characteristics in a partially liquid hydrogen tank, subject to fixed ambient temperature and wind velocity, has been investigated numerically. Three different insulation thickness were considered to investigate not only interfacial characteristics between liquid and ullage but thermo-fluid dynamics in hydrogen storage tank for various heat-leak situation. The results indicate that as the insulation thickness becomes thinner and more heat penetration exists, natural convection by buoyancy develops stronger, so strong vortices are created near the interfacial zone by upward flow driven by buoyancy. In particular, as the amount of heat in-leak increased, wider and stronger heat accumulation was found in the top dished head area of the ullage area. In addition, it was confirmed that the CFD model developed in this study could well describe the phenomenon in which the temperature of the tank wall and the insulation mat increased at a faster rate due to faster heat transfer from the vapor and interface. In the future, the numerical model developed in this study will be used for optimizing insulation system of storage tank for small-scale hydrogen which is cost-effective and highly efficient.

With the development of salt cavern gas storage construction technology, the construction of large-scale gas storage salt caverns using sediment voids is expected to solve the problem of low effective volume formation rate and poor construction economy of high-impurity salt mines. There are few studies on the long-term operation mechanical behavior of salt cavern gas storage under the influence of sediment accumulation currently. This paper studies the influence of sediment accumulation height, particle gradation, and operating pressure on the stability of salt caverns by constructing a coupling model of sediment particle discontinuous medium and surrounding rock continuous medium. The continuous-discontinuous coupling algorithm is suitable for analyzing the influence of particle accumulation height and particle gradation on the creep shrinkage of salt caverns. The increase of sediment accumulation height slows down the creep shrinkage of the bottom of the salt cavern, strengthens the restraining effect on the surrounding rock of the cavern, and moves the position of the maximum displacement of the surrounding rock to the upper part of the cavern; the sediment particle gradation has little effect on the cavern volume shrinkage rate, and the greater the coarse particle content, the smaller the cavern volume shrinkage rate; the greater the operating pressure, the more conducive to maintaining the stability of the cavern, slowing down the upward movement of the sediment body and increasing the gas storage space in the upper part of the cavern. This research results can provide a reference for evaluating the long-term operation stability of sediment-type high-impurity salt cavern gas storage.

The escalating concerns over climate change have propelled industries worldwide to seek innovative strategies for mitigating greenhouse gas emissions. Within the energy sector, Carbon Capture and Storage (CCS) technology emerges as a promising solution to curtail emissions and foster sustainable development aims for net zero approach. The research delves into the role of government support in expediting CCS adoption for the maximum potential of 9.79 MtCO2 storage from six major refinery plants. The refineries mentioned above are anticipated to necessitate an initial capital investment of approximately 18,307 million THB. This research focuses on potential business model proposals appropriate for a country's context, specifically applying CCS technology to Thai oil refining sector. To achieve the realization of CCS within the context of this study, a combination of three essential measures will be required: tax incentives, carbon credits, and grants. This process will commence with the implementation of tax incentives, followed by an increase in the carbon price within the country. Finally, the establishment of a dedicated fund, funded through deductions from oil excise tax revenue, will play a pivotal role in facilitating the necessary financial support for the emergence of CCS.

In order to achieve the dual carbon goal and simplify the decarbonization process, a CO2 recovery process of the fire-flooding exhaust was designed. The process adopted the two-stage membrane separation method to recover CO2 and obtain high purity CO2 rich flow, and then through the mixed refrigerant liquefaction and rectification column, food grade liquid CO2 was obtained. HYSYS process simulation shows that for the fire-flooding exhaust with a flow rate of 1000 kg/h and a given composition, the process can achieve a CO2 recovery of 69.02%, total product sales S=2086.8 yuan/h, and specific power consumption of 2.818 kW∙h/kg. On this basis, a hybrid simulation platform of HYSYS & Matlab was established. Taking the specific power consumption of the product as the objective function, sequential quadratic programming (SQP) algorithm was adopted to optimize the process, and the optimized specific power consumption was reduced by 18.8%. Finally, by adjusting N2/CO2 components, the adaptability of the optimization condition was analyzed.

In this work, the properties of a composition based on synthetic rubber ethylene-propylene ter-polymer and polymers with functional groups of the mixture are studied. Low efficiency of some compositions based on ethylene and propylene copolymer limits their use in the production of tires and rubber products. Therefore, we conducted a study to improve the disadvantages of SREPT-60 using butyl rubber + choro polyisoprene + butadiene-nitrile + butadiene styrene rubber and adding a plasticizer to the composition = α, methacrylate-(bis-diethylene glycol phthalate) -(btegf-9) The data obtained showed that a number of its indicators of rubber based on them were improved. Tear resistance, resistance to repeated stretching increased, adhesion of the composition to metal, chemical resistance increased, the degree of swelling in benzene and gasoline-benzene mixture decreased. Compositions based on the mixture SREPT-60 using butyl rubber + choro polyisoprene + butadiene-nitrile + butadiene styrene rubber and adding a plasticizer to the composition = α, methacrylate-(bis-diethylene glycol phthalate) -(btegf-9) +Dioctyl phthalate: (70:20:10) have high resistance to swelling in an aggressive environment (Benzene, gasoline, alcohol, acid, oil, etc.) mixture.

Electricity consumption is often the hotspot of life cycle assessment (LCA) of products, industrial activities, or services. The objective of this paper is to provide a consistent, scientific, region-specific electricity-supply-based inventory of electricity generation technology for national and regional power grids. Marginal electricity generation technology is pivotal in assessing impacts related to additional consumption of electricity. China covers a large geographical area with regional supply grids; these are arguably equally or less integrated. Meanwhile, it is also a country with internal imbalances in regional energy supply and demand. Therefore, we suggest an approach to achieve a geographical subdivision of the Chinese electricity grid, corresponding to the interprovincial regional power grids, namely the North, the Northeast, the East, the Central, the Northwest, and the Southwest China Grids, and the China Southern Power Grid. The approach combines information from the Chinese national plans on for capacity changes in both production and distribution grids, and knowledge of resource availability. The results show that nationally, marginal technology is coal-fired electricity generation, which is the same scenario in the North and Northwest China Grid. In the Northeast, East, and Central China Grid, nuclear power gradually replaces coal-fired electricity and becomes the marginal technology. In the Southwest China Grid and the China Southern Power Grid, the marginal electricity is hydropower towards 2030.

As waterflooding multi-layer reservoirs get into the high-water-cut stage, inter-layer conflicts become increasingly serious, leading to a worsening development effect over time. Production layers regroup is an effective approach for resolving inter-layer conflicts and improving waterflooding efficiency. At the current stage, there are limitations for most of the methods of production layers regroup. This article proposes a smart method for optimizing the layer regroup plan based on genetic algorithm. Comprehensively considering various factors that affect the regroup of layers, based on the combination principle of "smaller intra-group variance and larger inter-group variance of each influencing factor are expected ", genetic algorithm is used to calculate the fitness value of the initial combination schemes, the advantageous schemes with higher fitness values are selected as the basis of the next generation. Then crossover and mutation operations are performed to those advantageous schemes to generate new schemes. Through continuous selection and evolution, until the global optimal solution with the highest fitness value is found, the optimal combination scheme is determined. Comparative analysis with numerical simulation results demonstrates the reliability of this intelligent method, with an increased oil recovery of 4.34% for the sample reservoir. Unlike selecting a preferable plan from a limited number of predefined combination schemes, this method is an automatic optimization to solve the optimal solution of the problem. It improves both efficiency and accuracy as compared to conventional reservoir engineering methods, numerical simulation methods and most of the mathematical methods, thus could provide effective guidance for EOR strategies of waterflooding reservoirs in high-water-cut stage.

In order to establish the formation patterns of the Co–Mg oxide system, samples with different Co:Mg ratios and heat treatment temperatures were synthesized and studied. Study of the sam-ples confirmed the phase transition of MgxCo2–xO4 spinels into corresponding solid solutions at 800–900 °C. The similarity of formation patterns for different compositions is shown. The rock-salt oxide in low-temperature samples is an anion-modified paracrystalline phase that forms a “true” solid solution only upon spinel decomposition. TPR profiles of decomposed Co3O4 spinel show surface Co3O4 peaks and a wide peak corresponding to well-crystallized CoO, while par-tial Co3O4 TPR up to 380 °C results in dispersed and amorphous CoO. High-temperature non-stoichiometric samples are poorly reduced, indicating their low oxygen reactivity. Spinel reoxidation after heat treatment to 1100 °C by calcination at 750 °C showed complete regenera-tion for MgCo2O4–Co3O4 samples and its absence in case of an excess of MgO relative to stoi-chiometry. Based on the data obtained, it can be concluded that the processes governing the formation of Co–Mg oxide systems are determined by both Co:Mg ratio and the heat treatment conditions, potentially providing the possibility of fine tuning for specific catalytic processes.

The cold-pressed hempseed oil (HO) has been increasingly exploited in human diet for its excellent nutritional and healthy properties. However, it has a high content of polyunsaturated fatty acids (PUFAs) and chlorophylls, which inevitably accelerate its oxidative deterioration, especially in presence of light. In this scenario, the filtration technology may ameliorate the oxidative stability of the oil, with positive effects on its nutritional quality and shelf-life. Therefore, in this study, the oxidative stability and minor compounds of non-filtered and filtered HO (NF-HO and F-HO) were monitored over 12 weeks of storage in transparent glass bottles. F-HO showed a better hydrolytic and oxidative status than NF-HO during storage. As a result, F-HO displayed also a better preservation of total MUFA and PUFA in the autoxidation process. Filtration consistently reduced chlorophylls, thus, causing a variation of the natural color of HO. Accordingly, F-HO not only revealed an increased resistance to photooxidation but was also suitable for storage in clear bottles within 12 weeks. F-HO predictably showed lower carotenoids, tocopherols, polyphenols, and squalene compared to NF-HO. However, filtration appeared to play a “protective role” toward these antioxidants, which had lower degradation rates in F-HO than NF-HO for 12 weeks. Interestingly, the element profile of HO was not affected by filtration and remained stable during the study period. Overall, this study may be of practical use to both producers and marketers of cold-pressed HO.

In recent years, due to the detrimental impact of traditional gas-liquid refrigerants on the environment, the pursuit of solid-state refrigeration technology based on elastocaloric effect, as a promising sustainable alternative, has been promoted. However, the traditional trial-and-error method is inefficient and difficult to meet the material application requirements. In this work, machine learning (ML) was employed to accelerate the development of NiTi-based shape memory alloy (SMA) with excellent elastocaloric effect. By means of active learning, we identified 9 novel NiTi-based SMAs in four iterations, the phase transformation-induced entropy change (ΔS) of which are as high as over 90 J/kg·K-1. Moreover, the model exhibits good interpretability, allowing us to understand the relevance between the target and features from the aspect of mechanism.

Analyses of the three predominant types of sedimentation – clastic, carbonate and black shale – revealed their discontinuity/continuity in different facies environments of the Middle and Late Devonian of the central part of the Volga-Urals petroleum province, namely (1) in depressions, both condensed and non-condensed, (2) on the slopes of depressions and (3) in shallow water environments represented by tectonic arches or localised biohermal uplifts. The regional zonation of conodonts, correlated with the global chronostratigraphic scheme, substantiates the stratigraphic completeness of the general Devonian sequence in this area. In particular, the sedimentation of organic-rich black shales, traditionally considered as source rocks, lasted more than 29 million years, starting from the Late Eifel and ending at the Devonian-Carboniferous boundary. There was only one hiatus in the deposition of both black shales and carbonate sediments, lasting about 2.5 million years at the end of the Frasnian. That interval is dominated by clastic sediments, which are considered to be the most productive reservoirs of the Volga-Ural province. In the time interval from the beginning of the Eifel to the end of the Frasnian (about 17 Ma), (a) clastic sediments show the highest accumulation rates; (b) the most complete sequences occur in depressions; and (c) arches and uplifts show the most significant gaps in the geological record. During Famennian, (a) clastic sedimentation has completely ceased; (b) differences between the slopes of troughs and shallow-water environments have diminished, resulting in stable accumulation of carbonate sediments in both settings; (c) the decrease in sequence thickness (up to 50 m) in depressions suggests reduced accumulation rates of deep-water organic-rich black shales. The results help to understand the complex spatial relationship between different coexisting sedimentation types and focus attention to the incompleteness of the geological record in different environments.

Sous-vide is a process in which food is vacuum-sealed and prepared in a water bath, heated to a precise temperature, and circulated in a sous-vide machine. This cooking technique is increasingly common in homes and catering establishments due to its simplicity and affordability. However, manufacturers' and chefs' recommendations for low-temperature and long-term sous-vide cooking in media raise food safety concerns, particularly when preparing beef tenderloin. In this study, Salmonella enterica was found to be inactivated by heat and sage essential oil (EO) in beef tenderloin from musculus psoas major that had undergone sous-vide processing. To determine whether heat treatment was likely to increase the sous-vide efficiency, S. enterica and sage EO were mixed. After being vacuum-packed and injected with S. enterica, the samples were cooked sous-vide for the prescribed time at 50, 55, 60, or 65 °C. On days 1, 3, and 6, the amounts of S. enterica, total bacteria, and coliform bacteria were measured in both groups of sous vide beef tenderloin. Mass spectrometry was used to identify bacterial strains on various days and categories. Each day that was measured, the test group exposed to a temperature of 50 °C for 5 minutes had a higher number of all microbiota. The most isolated microorganisms from the control and treated groups were Pseudomonas fragi, and in the treated group also S. enterica. It has been shown that adding sage essence oil (EO) in combination with the sous-vide gastronomic method leads to the stabilization and safety of beef tenderloin.

High-precision conical threads are widely used in responsible joints in the drilling of oil and gas wells. Difficult underground drilling conditions due to the occurrence of significant mechanical loads and an aggressive environment in wells require the use of workable materials that are often difficult to machine. The huge need for such connections dictates the use of high-performance cutting tools, which means that high demands are placed on their effective geometric performance. The study describes the theoretical dependence of the profile precision of the tapered drill-string tool-joint threads of all standard sizes on the complex of a cutting tool geometric parameters and cutting tool setting accuracy. The experiments include an assessment of the geometric accuracy of the profile of the obtained NC23 thread connector, depending on the values of the installation angles and the declared tangential displacement of the standard threaded carbide insert.

Energy storage systems play a crucial role in the overall performance of hybrid electric vehicles. Therefore, the state of the art in energy storage systems for hybrid electric vehicles has been discussed in this paper along with appropriate background information for facilitating future research in this domain. Specifically, we have compared the key parameters such as cost, power density, energy density, cycle life, and response time for various energy storage systems. For the energy storage systems employing ultra capacitors, we have presented the characteristics such as cell voltage, cycle life, power density and energy density. Furthermore, we have discussed and evaluated the interconnection topologies for the existing energy storage systems. We have also discussed the hybrid battery-flywheel energy storage system as well as the mathematical modeling of the battery-ultracapacitor energy storage system. Toward the end, we have discussed energy efficient powertrain for hybrid electric vehicles.

An approach of implementing X-bar and R control charts as a statistical control tool to monitor changes in the melting profile of fresh and stored flaxseed oils by differential scanning calorimetry (DSC) was used. Phase transition melting profiles were collected after 0, 2, 4, 6 months of storing flaxseed oils, originated from five different cultivars. Four peaks at around -36, -30, -25, -12 °C were identified using the deconvolution analysis procedure, which enabled data to be collected on peak temperature (T), peak height (h) and the peak area (A), as well as the ratio calculated from these parameters. Control charts of DSC parameters, linked to the second peak (h2, A2) and calculated ratios of those parameters showed an increasing or decreasing trend within the storage time, thus were considered to be indicators of oil deterioration. Since DSC parameters related to the first peak (h1, A1) and third peak (h3, A3) remained unchanged within storage, they were established as the markers of flaxseed oil authenticity.

Soluble inorganic pyrophosphatase (sPPase), a pyrophosphate hydrolase, has been shown to play an important role in several physiological processes such as plant growth and development, metabolic activities, and response to abiotic stresses, but sPPase has been less studied in woody plants. In order to preliminarily verify whether the soluble inorganic pyrophosphatase in Eucommia ulmoides Oliver (E. ulmoides) has a role in resistance to drought stress, we amplified the EuSIP5 (E. ulmoides soluble inorganic pyrophosphatase 5) cDNA sequence from E. ulmoides by RT-PCR. In order to study the drought resistance of the Eucommia ulmoides soluble inorganic pyrophosphatase 5 (EuSIP5) gene, the cDNA sequence of the EuSIP5 gene was amplified from Eucommia ulmoides Oliver by RT-PCR. Bioinformatic analysis indicated that EuSIP5 might be an unstable amphipathic protein, mainly located in the cytoplasm. E. ulmoides, the highest expression of the EuSIP5 gene was found in male leaves and pericarp from April to October, and in leaves of E. ulmoides in July and September. During drought, the expression of EuSIP5 in seedling E. ulmoides leaves was significantly higher than that of the control. An overexpression vector harboring the EuSIP5 was constructed and introduced into the tobacco (Nicotiana tabacum cv. Xanthi). We found that during drought stress, the appearance of wilting was delayed by 4 days in transgenic tobacco plants (OE) compared with wild type plants (WT), and the expression of drought-related genes DET2, CYP85A1, P5CS, ERF1 and F-box was found to be increased in transgenic tobacco leaves, as well as the enzyme activities of the protective enzymes: peroxidase (POD), superoxide dismutase (SOD) and catalase (CAT) were significantly higher than those of the WT, and the malondialdehyde (MDA) content was lower than the WT. These results indicated that the introduction of EuSIP5 gene into tobacco increased the expression of drought-related genes, enhanced the anti-membrane oxidation ability of tobacco, and reduced the oxidative stress damage, thus improving the drought resistance of tobacco.

This work presents an innovative application of optimal control theory to the strategic scheduling of battery storage in the day-ahead electricity market, with a focus on enhancing profitability while factoring in battery degradation. The study incorporates in the optimisation framework the cost of battery capacity degradation, the effects of capacity degradation and internal resistance degradation into dynamics. We employ a continuous-time representation of the dynamics, in contrast with many other studies that use a discrete-time approximation with rather coarse intervals. We adopt an equivalent circuit model coupled with empirical degradation parameters to simulate a battery cell’s behaviour and degradation mechanisms with good support from experimental data. Utilising direct collocation methods with mesh refinement allows for precise numerical solutions to the complex, nonlinear dynamics involved. Through a detailed case study of Belgium’s day-ahead electricity market, we determine the optimal charging and discharging schedules under varying objectives: maximizing net revenues, profits considering capacity degradation, and profits considering both capacity degradation and internal resistance increase due to degradation. The results demonstrate the viability of our approach and underscore the significance of integrating degradation costs into the market strategy for battery operators, alongside its effects on the battery’s dynamic behaviour. Our methodology extends previous work by offering a more comprehensive model that empirically captures the intricacies of battery degradation, including a fine and adaptive time domain representation, focusing on the day-ahead market, and utilising accurate direct methods for optimal control. The paper concludes with insights into the potential of optimal control applications in energy markets and suggestions for future research avenues.

In order to develop novel botanical insecticides, the joint action of Ligusticum chuanxiong oil (LCO) and lemongrass oil (LO) against Aphis citricola van der Goot was determined systematically indoors and outdoors. The chemical profiles of LCO and LO as determined by gas chromatography- mass spectrometry analysis revealed that main compounds from LCO were Z-Ligustilide (44.58%) and Senkyunolide A (26.92%), and that of LO were geranial (42.16%) and neral (32.58%), respectively. The mixture of LCO and LO showed significant synergy against A. citricola, with a common-toxicity coefficient (CTC) value of 221.46 at the optimal ratio of LCO to LO (4: 1, w/w). Based on the results of solvents and emulsifiers screening, L. Chuanxiong oil · Lemongrass oil 20% emulsifiable concentrate (20% LCO · LO EC) was developed, which was confirmed to meet the requirements of a commercial pesticide by quality test. Field trials indicated that the insecticidal activity of the diluted 20% LCO · LO EC (1000 fold dilution) was comparable to conventional pesticide (20% imidacloprid EC) on A. citricola 7 days after application. Thus, the mixture of LCO and LO has the potential to be further developed as a botanical pesticide.

This paper presents a device for measuring and maintaining the constant water level in a tank. The device uses a capacity sensor to measure the water level. The sensor has a DC voltage output proportional to the water level in the tank. This voltage can be used in other automation too. The water level, in percentages, is displayed on a vu meter with 8 LEDs. The circuit for maintaining the constant level consists in a comparator with hysteresis. The level of the water is adjustable, using a reference voltage from a potentiometer (marked in percentages). The level of the water is compared with the prescribed level and the difference between them commands the start/stop of the water pump which supplies the tank through a relay. The device is powered by 220 V and is isolated from the environment.

The study aimed to compare the cardiovascular benefits of Omega-3 Polyunsaturated Fatty Acids from fish oil versus krill oil in different forms and dosages. Following PRISMA 2015, data analysis with R software, and databases were searched from 1993 to 2023, (ID PROSPERO: CRD42024502338). Sixty high-quality studies were analyzed, covering various forms of fish oil and krill oil at different dosages (fish oil (ethyl ester-EE, triglyceride-TG, re-esterified triglycerides-rTG, capsules, emulsion-EM); krill oil (phospholipid/free fatty acid-PL/FFA, high concentration phospholipid-HPL, low concentration phospholipid-LPL)). Meta-analysis revealed that krill oil with phospholipid/free fatty acid at doses 2000-2900 mg effectively lowered triglycerides, while fish oil in ethyl ester form at doses above 3000 mg significantly reduced total cholesterol. Fish oil in triglyceride form at doses 2000-2900 mg and other variations positively impacted HDL-C levels. Fish oil in EE form above 3000 mg and triglyceride form below 2000 mg notably reduced LDL-C. However, there was limited effectiveness observed for other interventions. Analysis for LDL-C exhibited publication bias, while other parameters demonstrated reliability (Egger's test). In conclusion, krill oil - PL/FFA, Fish oil - EE above 3000 mg, Fish oil - TG 2000-3000 mg, and fish oil - rTAG 300-1900 mg effectively in reducing heart risk patients.

Incorporating renewables in the power grid presents challenges for stability, reliability, and operational efficiency. Integrating Energy Storage Systems (ESS) offers a solution by managing unpredictable loads, enhancing reliability, and serving the grid. Hybrid storage solutions have gained attention for specific applications, suggesting higher performance in some respects. This paper compares the performance of hybrid energy storage systems (HESS) to single battery, evaluating their energy supply cost and environmental impact through optimization problems. The model generates an optimized dispatch, minimizing cost or environmental impact of supplying energy to a generic load while considering battery degradation. Seven technologies are assessed, with an example applied to an industrial site contrasting vanadium redox flow (VRFB) and lithium batteries considering the demand of a local load (building). The results also indicates that efficiency and degradation curves have the highest impact in the final costs and environmental functions on the various storage technologies assessed. For the simulations of the example case, a single system only outperforms the hybrid system in cases where lithium efficiency is higher than approximately 87% and vanadium is lower approximately 82%.

The ubiquitous presence of microplastics (MPs) in the environment poses a threat to ecosystems and increases concerns about their exposure to the human body. However, despite being consumed for health improvement, limited research has been conducted on MPs in functional foods. This study aimed to investigate the occurrence of MPs and the relation of the source of raw material or the manufacture in various omega-3 oil in the Korean market. MPs in omega-3 capsule and raw oil, sourced from both plant-based (PB) and animal-based (AB) sources, were investigated. We developed the method by direct filtration with acetone washing and analyzed MPs greater than 5 μm using microscope-Raman spectroscopy. The average number of MPs was found to be 1.2 ± 1.7 MPs/g for PB raw oil, 2.2 ± 1.7 MPs/g for AB raw oil, 3.5 ± 3.9 MPs/g for PB capsule oil, and 10.6 ± 8.9 MPs/g for AB capsule oil. Polypropylene and polyethylene terephthalate were major specious (83-95 %) found in omega-3 oil. The ratio of size range remained consistent across all groups, with a trend of higher detection rates as the size diminished. The results reveal that the main reason of MPs contamination is not the source of raw material but the manufacturing and packaging process for omega-3 oil.

The article delves into the crucial realm of compressing hydrogen in its gaseous state, a pivotal process for enhancing its viability in both civil and industrial sectors. The study initiates by providing a concise overview and comparison of diverse hydrogen storage methodologies, laying the groundwork with an in-depth analysis of hydrogen's thermophysical properties. It scrutinizes plausible configurations for hydrogen compression, aiming to strike a delicate balance between energy consumption, predominantly derived from the fuel itself, and the requisite number of compression stages. Notably, to render hydrogen storage competitive in terms of volume, pressures of at least 350 bar are deemed essential, albeit at an energy cost amounting to approximately 10% of the fuel's calorific value. Multi-stage compression emerges as a crucial strategy, not solely for energy efficiency, but also to curtail temperature rise, with an upper limit set at 200°C. This nuanced approach is underlined by the exploration of compression levels commonly cited in the literature, particularly 350 bar and 700 bar. Ultimately, the study advocates for a three-stage compression system as a pragmatic compromise, capable of achieving high-pressure solutions while keeping compression work below 10 MJ/kg, a threshold indicative of sustainable energy utilization.

As the adoption of renewable energy sources grows, ensuring a stable power balance across various time frames has become a central challenge for modern power systems. In line with the "dual carbon" objectives and the seamless integration of renewable energy sources, harnessing the advantages of various energy storage resources and coordinating the operation of long-term and short-term storage have become pivotal directions for future energy storage deployment. To address the complexities arising from the coupling of different time scales in optimizing energy storage capacity, this paper proposes a method for energy storage planning that accounts for power imbalance risks across multiple time scales. Initially, the Seasonal and Trend decomposition using the Loess (STL) decomposition method is utilized to temporally decouple actual operational data. Subsequently, power balance computations are performed based on the obtained data at various time scales to optimize the allocation of different types of energy storage capacities and assess the associated imbalance risks. Finally, the effectiveness of the proposed approach is validated through hourly applications using real-world data from a province in China over recent years.

Jerusalem artichoke juice is valued for its nutritional content and health benefits. Spontaneous fermentation enhances its flavor, quality, and functional components through microbial metabolic activities. This study used high-throughput sequencing to analyze microbial community changes and LC-MS and GC-MS to detect secondary metabolites and flavor compounds during fermentation. During the natural fermentation, beneficial bacteria like Lactobacillus and Pediococcus increased, promoting lactic acid production and inhibiting harmful bacteria, while environmental bacteria decreased. Similarly, fungi shifted from environmental types like Geosmithia and Alternaria to fermentation-associated Pichia and Penicillium. A total of 1, 666 secondary metabolites were identified, with 595 upregulated and 497 downregulated. Key metabolic pathways included phenylpropanoid biosynthesis, with significant increases in phenylalanine, tryptophan, and related metabolites. Lipid and nucleotide metabolism also showed significant changes. Flavor compounds, including 134 identified alcohols, esters, acids, and ketones, mostly increased in content after fermentation. Notable increases were seen in Phenylethyl Alcohol, Ethyl Benzenepropanoate, 3-Methylbutyl Butanoate, Ethyl 4-Methylpentanoate, 5-Ethyl-3-Hydroxy-4-Methyl-2(5H)-Furanone, Ethyl Decanoate, Hexanoic Acid, 1-Octanol. γ-aminobutyric acid (GABA) and other functional components enhanced the health value of the juice. This study provides insights into microbial and metabolic changes during fermentation, aiding in optimizing processes and improving the quality of fermented Jerusalem artichoke juice for functional food development.

This paper designed a new type of generator, transgenerator, that integrates the wind turbine and flywheel into one system, aiming to make the flywheel distributed energy storage (FDES) more modular and scalable than the conventional FDES. The transgenerator is a three-member dual-mechanical-port (DMP) machine with two rotating members (inner and outer rotors) and one stationary member (stator). The transgenerator-flywheel system is introduced with the system configuration, transgenerator overview, flywheel operation principle and power management strategies, and control system. Simulations are performed in MATLAB/ Simulink to verify the system viability, including control system verification and the flywheel storage performance evaluation. Results show that the inner and outer rotors can be controlled independently with accurate and fast control response, and the grid-side control works properly. The flywheel performs well with considerable charging power and storage capacity.

The formation of hydrogen sulfide (H₂S) in petroleum reservoirs by anaerobic microbial activity is called biogenic souring of reservoirs and is a risk in the oil and gas industry as the compound is extremely toxic, flammable and corrosive. In this paper, we present a workflow and the tools to assess biogenic souring from a pragmatic engineering perspective. The retention of H₂S in the reservoir due to the reactions with iron-bearing rock minerals (e.g. siderite) is shown in a theoretical approach here and supported with literature data. Cases are given for two fields under secondary (waterflooding) and tertiary flooding with microbial enhanced oil recovery (MEOR). The use of the Monte Carlo method as a numerical modelling tool to incorporate uncertainties in the measured physical/chemical/ biochemical data is demonstrated as well. A list of studies conducted with different chemicals alone or in combination with various biocides to mitigate biogenic souring provides an overview of potential inhibitors as well as possible applications. Furthermore, the results of static and dynamic inhibition tests using molybdate are presented in more detail due to its promising mitigation ability. Finally, a three-step workflow for the risk assessment of biogenic souring and its possible mitigation is presented and discussed.

Using density functional theory (DFT), the density of states of NH4V3O8 (NVO) was analyzed pre and post-oxygen defects (Od) formation. The findings revealed a reduced bandgap in NVO after Od introduction, emphasizing the role of Od in enhancing conductivity of the material, thus improving its electrochemical attributes. Through the water bath method, both NVO and its oxygen-deficient counterpart, (NH4)2V10O25⸱8H2O (NVOd), were synthesized as potential cathode materials for aqueous zinc-ion batteries (AZIBs). Experimental outcomes resonated with DFT predictions, highlighting the beneficial role of oxygen defects in boosting electrical conductivity. Notably, the refined material displayed a remarkable capacity of 479.3 mAh g-1 at 0.1 A g-1, underscoring its promise for advanced energy storage solutions.

The paper presents a method to assess the effect of electrolyte additives on the energy capacity of Pb-acid batteries. The method applies to any chemically unreactive additive, including suspensions and gels. The approach is thermodynamically based and it leads to the definition of a region of admissible concentrations –the battery’s admissible range– where the battery can undergo an indefinite number of charge/discharge cycles without suffering permanent damage. An experimental procedure to determine this range is presented. The obtained results provide a way to assess the potential of electrolyte additives to improve the energy capacity of Pb-acid batteries. The same results also provide a means to determine the additive concentration that produces the maximum energy capacity increase of the battery. The paper closes with an example of application of the proposed approach to a practical case.

The one-dimensional MoS₂/carbon nanofibers (1D MoS₂/CNFs) are synthesized by electrospinning using exfoliated MoS₂ nanosheets and polyacrylonitrile as raw materials. The exfoliated MoS₂ nanosheets with size of about 150 nm are encapsulated in carbon nanofibers, and the free-standing MoS₂/CNFs can be easily cut into flexible tablet and directly used as binder-free anode for lithium storage. The resultant 1D MoS₂/CNFs exhibit a very high reversible capacity of 700 mAh g^-1 at 100 mA g^-1 after 50 cycles, high rate capacity (450 mAh g^-1 at 1000 mA g^-1 after 200 cycles) and good cycle stability.

Nowadays, the fingerprinting methodologies of olive oils are dominated. They consider the entire analytical signal, which is acquired and recorded by the analytical instrument, directly from olive oil or isoleted fraction, i,e chromatogram. The shape and intensity of the recorded signal the instrumental fingerprint from the whole olive oil adulteration. Therefore, the methodolygy is based on the chemical composition (Fatty acids and Triglycerides compositions). However, Fatty acids composition as an indicator of purity suggests that linolenic acid content could be used as a parameter for the detection of extra virgin olive oil fraud with 5% of soybean oil. The adulteration could also be detected by the increase of the trans-fatty acid contents with 3% of soybean oil, 2% of corn oil and 4% of sunflower oil. The use of the ∆ECN42 proved to be effective in the Chemlali extra-virgin olive oil adulteration even at low levels: 1% of sunflower oil, 3% of soybean oil and 3% of corn oil. Therefore, compared to classical methods PCA and new approach of using LDA application could represent an alternative and innovative tool for faster and cheaper evaluation of extra-virgin olive oil adulteration.

This paper reviews the multiple roles of machine learning in improving the resilience of power grids, especially in applying new energy storage technologies. Energy storage technologies, such as compressed air energy storage, flywheel energy storage, and superconducting coil energy storage, significantly improve the power grid's ability to respond to load fluctuations and emergencies through intelligent control and optimisation of machine learning algorithms. This not only helps to optimise energy dispatch and improve the operational efficiency and flexibility of the grid but also significantly improves the stability and reliability of the grid so that it is better able to meet future challenges and needs.

Compressed carbon dioxide energy storage (CCES) offers several benefits over other existing energy storage systems, including ease of liquefaction, high energy storage density, and environmental friendliness. As a result, the research progress, economic and technological feasibility, and system operation of the CCES system are all discussed in depth in this study. The system evaluation method is summarized and the compressed carbon dioxide storage is analyzed, and the performance optimization direction of the compressed carbon dioxide energy storage technology is discussed. When the overall performance of a transcritical CCES system, a supercritical CCES system and a liquid CCES system are compared, it is discovered that the supercritical CCES system has better thermodynamic characteristics and a simpler system configuration, making it suitable for large-scale development and use. The goal of the CCES system's future development is to create a design with an optimum compression and expansion ratio, a more precise analysis and system model, and multi-field coupling. This review's discussion serves as a guide for the best design and use of the CCES system.

Hydrogen storage in general is an indispensable prerequisite for the introduction of a hydrogen energy based infrastructure. In this respect, high-pressure metal hydride (MH) tank systems appear to be one of the most promising hydrogen storage techniques for automotive applications using proton exchange membrane (PEM) fuel cells. These systems bear the potential of achieving a beneficial compromise of comparably large volumetric storage density, a wide working temperature range, comparably low liberation of heat, and increased safety. The debatable term unstable metal hydride stands in the literature short for metal hydrides with high dissociation pressure at comparably low temperature. Such compounds may help to improve the merit of high-pressure MH tank systems. Consequently, in the last few years, some materials for possible on-board applications in such tank systems have been developed. This review summarizes the state-of-the-art developments of these metal hydrides, mainly including intermetallic compounds and complex hydrides and gives some guidelines for future developments. Since typical laboratory hydrogen uptake measurements are limited to 200 bar, a possible threshold for defining unstable hydrides could be a value of their equilibrium pressure of peq > 200 bar for T < 100°C. However, these values would mark a technological future target and most current materials, and those reported in this review, do not fulfill these requirements and need to be seen as current stages of development towards the intended target. For each of the aforementioned categories in the review, special care was taken not only to covers the pioneering and classical research, but also to portrait the current status and latest advances. For intermetallic compounds, key aspects focus on the influence of partial substitution on absorption/desorption plateau pressure, hydrogen storage capacity and hysteresis properties. For complex hydrides, the preparation procedures, thermodynamics and theoretical calculation are presented. Besides, challenges, perspectives, and development tendency of this field are also discussed.

Infill drilling is one of the most effective methods to improve the performance of poly-mer flooding. The difficulties related to infill drilling are determining the optimal numbers and placements of infill wells. In this study, an improved archimedes optimization algorithm with Halton sequence (HS-AOA) was proposed to overcome the aforementioned difficulties. First, to optimize the infill well placement for polymer flooding, an objective function that considered the economic influence of infill drilling was developed. Then, the novel optimization algorithm (HS-AOA) for infill well placement was developed by combining the AOA with the Halton se-quence. The codes were developed in MATLAB and connected to a commercial reservoir simula-tor CMG STARS to carry out the infill well placement optimization. Finally, the HS-AOA was compared to the basic AOA to confirm its reliability and then used to optimize the infill well placements for polymer flooding in a typical offshore oil reservoir. The results showed that the introduction of the Halton sequence into AOA effectively increased the diversity of the initial ob-jects in the AOA and avoided the HS-AOA trapping into the local optimal solutions. The HS–AOA outperformed the AOA. It was an effective approach to optimize the infill well placement for polymer flooding processes. In addition, infill drilling could effectively and economically im-prove the polymer flooding performance in offshore oil reservoirs. The NPV of the polymer flooding case with infill wells determined by HS-AOA reached 3.5 × 108 $, which was an increase of 7% over that of the polymer flooding case. This study presents an effective method for opti-mizing infill well placement for polymer flooding processes. It also can serve as a valuable refer-ence for other optimization problems in the petroleum industry, such as joint optimization of well control and placement.

In Tunisia, olive is the most cultivated fruit crop while in the north where rainfall exceeded 400mm.year-1, the olive growing area is in widely extension in marginal soil with high slope gradient. Thus, the inclusion of cover crops is a sustainable solution to increase the ecosystem productivity, improve the soil fertility and oil yields. But, in Tunisia a few study were investigated the effect of legumes cover crop on the olive productivity. Therefore, the aim of this study was to evaluate the short-term (two cropping seasons s 2021 and 2022) effects of different seeded cover crops and soil management practices on the cover crops and soil characteristics, as well as enzymes activities and related microbial diversity. Six intercropping were tested in rainfed olive orchards (cv.Chétoui): Spontaneous vegetation (Spont), Wheat, Vetch, Oat, Fenugreek, mixture Vetch-Oat and compared to control (3 periodic tillage/year without intercropping). During the first cropping season, cover crops were cut as animal feed and only residues were incorporated into the soil. While, during the second year, all cover crops biomass were incorporated into the soil. Results indicate that the dry biomass and carbon uptake were significantly higher in grasses species (Wheat and Oat). But, highest level of nitrogen was found in Fenugreek cover crops. As compared to control, all cover crops including spontaneous vegetation increased soil organic matter and macronutrient level, mainly phosphorus. The most activity of β-glucosidase, phosphatase and arysulphatase was found in the cover crops plot of wheat and oat. In addition, this study improve that the utilization of the carbon sources was dominated by amides, amine and amino-acids in the fenugreek plot; while it was dominated by polymers and carboxylic acids in the case of wheat and oat.

Fractional calculus is defined by expanded integer order integration and differentiation. In this paper, multiple mathematical models of a nonlinear dual tank device are precisely formulated by fractional calculus. Using the accurate model, multivariable Fractional-Order Controller is designed for the nonlinear device. The merits of the fractional-order design include: 1) Control of multivariable nonlinearities, 2) Compensation of uncertainties, 3) Elimination of coupling effects. Simulations and experiments are conducted to verify the precision of the fractional order models and the effectiveness of the multivariable fractional-order control design.

The on-site wastewater treatment system (OWTS) with a sand trench is an economical option for residents in rural areas or the countryside where a centralised sewer system is inaccessible. 2A sand achieves improved filtration, microbial activity and consistent long term performance when compared to gravel or scoria based trench systems. However, it is expensive and only readily available in a few areas across New Zealand. Additionally, it has a reputation for premature blockage when overloaded or compacted. The aim of this study is not only to critically evaluate the performance of Crushed Glass (CG) with respect to 2A sand, but also to investigate different loading rates for CG when treating primary treated effluent from a septic tank. A test rig was designed and constructed to simulate the real environment of the sand column in a discharge control trench. The treatment efficiency of three filters was recorded and compared in this study. Overall, the CG loaded at 25mm/day (CG₂₅) and 50mm/day (CG₅₀) provided an average of 13% and 6% more Total Nitrogen (TN) reduction than the sand filter, respectively. The removal rates for the TN were up to 69.5%. The CG₅₀ filter performed similarly at 50mm/day as the 2A sand filter in terms of Total Suspended Solids (TSS) and Biochemical Oxygen Demand (BOD)₅ removal of more than 94%. The CG₂₅ removal rates for TSS and BOD₅ at the start of the trial (likely due to residual liquid contamination from the bottles when crushed) improved over the sampling period and ultimately achieved similar results of 92% and 91.3% to the filters loaded at 50mm/day. Lifecycle cost analyses and carbon balances were completed for the two media. It highlighted that the current price of CG is only half of 2A sand, yet it produces significantly less CO₂ emissions than 2A sand. A 3-bedroom dwelling could save up to $500 and reduce 200kg of CO₂ released to the environment annually when 2A sand is substituted for CG. Based on the findings of this paper, it is likely that the reduced installation cost, lessened environmental impact and theoretical availability will lead to CG systems becoming more common in New Zealand and abroad.

This paper presents the application of optimal control problem in modeling of stirred tank heater temperature control. The analysis of the open loop system shows that the system is not efficient without a controller. Linear Quadratic Gaussian (LQG) and Linear Quadratic Integral (LQI) controllers are used to increase the performance of the system. Comparison of the closed loop system with the proposed controllers have been done with Matlab/Simulink Toolbox and a promising results have been analyzed.

This article deals with special curves similar to those known in mathematics as Lamé curves. Their equations have a certain similarity with the equations of Lamé curves. But these curves are more like ellipses in appearance. Like ellipses, they have major and minor axes. These are such curves that their major and minor semi-axis coincide with an ellipse but are different than an ellipse. The main feature of these curves is that for any triangle whose base coincides with the axis of a given curve and the vertex is on a given curve, the condition aⁿ+bⁿ=cⁿ is obtained. The number “n” is called the degree or rank of this curve. To distinguish this group of curves, we called them Elbe curves. The equations of these lines are also provided in the paper.

Improper disposal of waste plastic has caused serious ecological and environmental pollution problems. Transforming plastics into high value-added chemicals can not only achieve efficient recycling of waste plastics, but also an effective way to control white pollution. The catalyst selectively breaks the C-C bond of polyolefin plastic under heat treatment and converts it into liquid fuel, thus realizing sustainable recycling of plastics and has a good development prospect. This review provides a detailed overview of the current development of catalytic pyrolysis, catalytic hydrolysis, solvent decomposition and supercritical hydrothermal liquefaction for cracking plastics to make fuel oil. The reaction mechanism, influencing factors and promoting effects of catalysts in various degradation technologies are analyzed and summarized and the latest proposed tandem reaction for degrading plastics is briefly introduced. Finally, some optimization paths of waste plastic pyrolysis to fuel oil technology are proposed: synergies between mixed raw materials, in-depth exploration of catalysts, design and manufacture of reactors that match the pyrolysis technology. All these are important research directions for promoting the industrialization of plastic pyrolysis to fuel oil.

Abstract: Commercialization of extra virgin olive oil (EVOO) requires a best before date recom-mended at up to 24 months after bottling, stored under specific conditions. Thus, it is expected that the product retains its chemical properties and preserves its ‘extra virgin’ category. However, in-adequate storage conditions could alter the properties of EVOO. In this study, Arbequina EVOO was exposed to five storage conditions for up to one year to study the effects on the quality of the oil and the compounds responsible for flavor. Every 15 or 30 days, samples from each storage condition were analyzed determining physicochemical parameters, the profiles of phenols, volatile compounds, α-tocopherol and antioxidant capacity. Principal component analysis was utilized to better elucidate the relationships between composition of EVOOs and the storage conditions. EVOOs stored at -23 and 23 °C in darkness and 23 °C with light, differed from the oils stored at 30 and 40 °C in darkness. The former were associated with higher quantity of non-oxidized phenolic compounds and the latter with higher elenolic acid, oxidized oleuropein and ligstroside derivatives, which also increased with storage time. E-2-Nonenal (detected at trace levels in fresh oil) was selected as a marker of the degradation of Arbequina EVOO quality over time, with significant linear regressions identified for the storage conditions at 30 and 40 °C. Therefore, early oxidation in EVOO could be monitored by measuring E2-Nonenal levels.

The existing methods of oil palm Fresh Fruit Bunch (FFB) evacuation from in-field to temporary collection point which typically apply medium to large tractors, often result in unexpected soil compaction. Meanwhile, smaller size equipment indicates low working capacity and unable to perform direct unloading to collection bin. This paper addresses the challenge of FFB evacuation by focusing on preventing soil compaction, increasing working capacity and enabling direct unloading to collection bin. For this purpose, a 6x6WD transporter prototype with a scissor lift mechanism was developed. With the design, the transporter could evacuate FFB in both steep mineral terrain and low ground pressure peatland, able to carry FFB with capacity of 750 kg and provide direct unloading into collection bin. The average field working capacity of the transporter was found to be 15 tons day-1. This research offers insights for future designs of medium-sized FFB transporters with advanced unloading mechanisms.

The criteria of “Distinctness, Uniformity and Stability” as well as a high "overall quality index” are used to register the Italian modern varieties to the national register. Differently, local conservation varieties can be certified under different EU Directives having, as overall objective, the preservation of biodiversity and the containment of genetic erosion. In recent years, products derived from an-cient grains are perceived to be healthier and more sustainable by consumer, especially in Italy, with consequent higher market prices. Ancient tetraploid wheat varieties registered in the national reg-ister of conservation varieties are 28, 24 of which are Sicilian. They are supposed to have a wide genetic variability compared to modern ones, making them vulnerable of fraud because they are difficult to trace. It is therefore important to have tools able to discriminate the autochthonous Si-cilian varieties. This can be done by gluten proteins composition, which also gives information on the technological properties of derived products. Fifty-one accessions belonging to 22 ancient va-rieties of Sicilian tetraploid (mostly durum) wheat were analyzed. Although a wide intra-accession and intra-varietal variability was assessed, the gliadin pattern of bulks of seeds belonging to each variety was discriminatory. Moreover, differences in technological attitudes were found between landraces. This paves the way to use gluten protein patterns for traceability allowing local farmers and producers to valorize their products and assure consumers about the transparency of the entire supply chain.

Endocrine disruptors are molecules that can interfere with the proper functioning of the endocrine system and lead to harmful effects in living organisms. This review focuses on the impact of synthetic fragrances, which are commonly found in personal care and household products, on the endocrine system. The article discusses the different types of hormones in the body and how they interact with receptors to produce signals. It also explores how endocrine disruptors can interfere with hormone signaling and transport, leading to adverse effects in the body. This work underscores the crucial need for further research into the impact of synthetic fragrances on the endocrine system and the importance of using safer alternatives in personal care and household products.

The utilization of natural waxes to form oleogels has emerged as a new and efficient technique for structuring liquid edible oil into solid-like structures for diverse food applications. The objective of this study was to investigate the interaction between sunflower wax (SW) and monoglycerides (MGs) in olive oil oleogels and to assess their physical characteristics and storage stability. To achieve this, pure SW and a combination of SW with MGs in a 1:1 ratio were examined within a total concentration range of 6-12% w/w. The formed oleogels were characterized based on their microstructure, melting and crystallization properties, textural characteristics, and oxidative stability during storage. All the oleogels were shelf-stable, and as the concentration increased, the hardness of the oleogels also increased. The crystals of SW oleogels were long needle-like, while the combination of SW and MGs led to the formation of crystal aggregates and rosette-like crystals. The differential scanning calorimetry and FTIR showed that the addition of MGs led to different crystal structures. The oxidation results revealed that oleogels had low peroxide and TBARS values throughout the 28-day storage. These results provide useful insights about the utilization of SW and MGs oleogels for potential applications in the food industry.

Ammonium sulfate has been utilized in agriculture; however, there is a dearth of research on its application in maize cultivation subsequent to the implementation of nitrification inhibitors or coating. This study aims to analyze the impacts of various combinations of ammonium sulfate fertilizers on soil nutrients, plant nutrient uptake, yield, and fertilizer utilization efficiency in maize cultivation to ascertain the optimal and stabilized disposal method for ammonium sulfate. A completely randomized design was employed with five treatments (AU, the control using urea; AS, treatment using ammonium sulfate; ASN, treatment using ammonium sulfate with a nitrification inhibitor; ASG, treatment using oil-coated ammonium sulfate; ASD, treatment using oil-humic acid-coated ammonium sulfate). Results showed that: (1) Compared with AU and AS, ASN, ASG and ASD decreased the leaching rates of TN, NH4+-N and NO3-N to the 10-20 cm soil layer, and more residual N was obtained in 0-10 cm soil layer. The first-order kinetic equation Nt=N0(1-e-kt) can better fit the process of nitrogen accumulation and release, and the N release rate constant is AU>CK>AS>ASH>ASN>ASD; (2) Compared with AU and AS treatments, the plant dry weight, grain dry weight, spike width, spike length, and yields of maize increased by 8.85-11.08%, 12.98-14.15%, 2.95-3.52%, 5.50-5.65%, and 43.21-51.10% under ASG treatment respectively. The impact of effective spike number on maize yield was found to be significant, as demonstrated by the path analysis conducted in this study. Furthermore, the accumulation levels of nitrogen, phosphorus, and potassium within above-ground plants significantly increased under the ASG treatment compared to the AU and AS treatments. The partial productivity of nitrogen, phosphorus, and potassium increased by 1.43-1.51-fold under ASG treatment, while grain nitrogen balance, grain phosphorus balance, and grain potassium balance increased by 1.41-1.58-fold, 1.51-1.95-fold, and 1.15-l.96-fold respectively. The oil-coated ammonium sulfate, therefore, exhibited the optimal slow-release effect of nutrients, thereby achieving superior performance in enhancing maize production and efficiency.

Rice prolamins are categorized into three groups by molecular size (10, 13, or 16 kDa), while the 13 kDa prolamins are assigned to four subgroups (Pro13a-I, Pro13a-II, Pro13b-I, and Pro13b-II) based on cysteine residue content. Here, we generated four knockout strains of rice using CRISPR-Cas9, each of which demonstrated selectively reduced expression of specific subgroups of the 13 kDa prolamins. These four mutant rice lines also demonstrated compensatory expression of glutelins and non-targeted prolamins, which resulted in low grain weight, altered starch content and atypically-shaped starch granules and protein bodies. Transcriptome analysis identified 746 transcripts that were differentially expressed in the mutant rice lines during development. These transcripts played roles primarily in RNA processing, protein synthesis, stress response, and transport. After selective suppression/knockout of genes in the Pro13a-I subgroup, compensatory upregulation of genes in the Pro13a-II and Pro13b-I/II subgroups was observed. Compensatory expression of 9 ER stress and 17 transcription factor genes was also observed in mutant rice in which expression of 13 kDa prolamin genes was suppressed. Our results provide valuable insight into the regulatory mechanisms underlying rice seed development and the specific roles played by 13 kDa rice prolamins and their target genes.

Solvent free copolymerization of epoxides derived from fatty acid esters of waste cooking oil with phthalic anhydride using (salen)CrIII Cl as catalyst and n-Bu4NCl/DMAP as co-catalyst was carried out for the first time under microwave irradiation, where reaction time was reduced from number of hours to minutes. The polyesters were obtained with molecular weight (Mw = 3084-6740 g/mol) and dispersity values (D = 1.18-1.92), when (salen)CrIII Cl/n-Bu4NCl was used as catalysts. While in case of DMAP as a co-catalyst, polyesters with improved molecular weight (Mw = 5537-6925 g/mol) and narrow dispersity values (D = 1.07-1.28) were obtained even at reduced concentrations of (salen)CrIII Cl and DMAP. The obtained products were characterized and evaluated by attenuated total reflection-fourier transform infrared spectroscopy (ATR-FTIR), proton nuclear magnetic resonance (1H-NMR) spectroscopy, gel permeation chromatography (GPC) and thermogravimetric analysis (TGA) Techniques.

This work examines the beneficial role of an unsteady stenosis, operating without the use of any external energy source, as a means for augmenting the flow rate of a valveless pump in a hydraulic loop, including an open tank. In contrast to our previous work that the loop was horizontal, here gravity was taken into account. The stenosis neck cross-sectional area was controlled by the fluid pressure and an opposing force applied externally by a spring of adjustable tension. The pincher compressed and decompressed periodically a part of a flexible tube with frequencies from 5 Hz to 11 Hz and compression ratios Ab from 24% to 65%. The presence of the stenosis increased the net flow rate 19 times for Ab = 24%, and 6.3 times for Ab = 38%, whereas for Ab = 65%, the flow rates were comparable. The volumetric efficiency varied from 30% to 40% under the presence of the stenosis, and from 2% to 20% without the stenosis. The role of the stenosis role was to cause a unidirectional flow, opening during tube compression and closing during decompression. The pressure amplitudes along the flexible tube increased towards the rigid-flexible tube junction (as a result of the wave reflections) which were found to be significantly attenuated by the presence of the stenosis.

Experimental test facilities are generally characterised using linear transfer functions to relate the wavemaker forcing amplitude to wave elevation at a probe located in the wavetank. Second and third order correction methods are becoming available but are limited to certain ranges of waves in their applicability. Artificial intelligence has been shown to be a suitable tool to find even highly nonlinear functional relationships. This paper reports on a numerical wavetank implemented using the OpenFOAM software package which is characterised using artificial intelligence. The aim of the research is to train neural networks to represent non-linear transfer functions mapping a desired surface-elevation time-trace at a probe to the wavemaker input required to create it. These first results already demonstrate the viability of the approach and the suitability of a single setup to find solutions over a wide range of sea states and wave characteristics.

This paper investigates the tank drainage problem of an isothermal, unsteady, incompressible electrically conducting Power law fluid. Analytic solution have been obtained from governing continuity and momentum equations subject to appropriate boundary conditions by using Perturbation method. The Power law fluid model solution without MHD is retrieved from this proposed model on substitution . Declaration on behalf of velocity profile, volume flux, average velocity, connection of time with respect to length of the tank and requirement of time for whole drainage of fluid are acquired. Special effects of numerous emerging parameter’s on velocity profile vz and depth of the fluid in the tank are graphically presented. Keywords: Tank drainage, Power law MHD fluid, Analytical solution.

Carbon (C) losses due to the conversion of natural forests adversely affect the abiotic components of terrestrial ecosystems. In tropical China, rubber cultivation often extends from its traditional range to elevations of up to 1400 m. However, C storage in rubber plantations across elevation gradients is poorly understood. In this study, we investigated biomass and C storage along elevation gradients in two age groups (8- and 12-year-old) of rubber monoculture plantations in Xishuangbanna, Southwest China. We investigated the C distribution across various tree sections, ranging from aboveground biomass (AGB) to belowground biomass (BGB), including litter, big dead branches, and different soil depths. A significant negative correlation was observed between total ecosystem C stocks and elevation in both age groups of rubber plantations. The highest ecosystem C stock of 197.90 Mg C ha–1 was recorded at 900 m in 8-year-old plantations, whereas in 12-year-old rubber plantations, the highest value of 183.12 Mg C ha–1 was found at 700 m. The total ecosystem C stocks decreased to its lowest level at 1000 m in both the 8-year-old and 12-year-old plantations, ranging between 113.05 Mg C ha–1 and 125.75 Mg C ha–1, respectively. We concluded that the total ecosystem C stocks were negatively correlated with elevation and significantly decreased from 8.05% to 51.55% and 11.46% to 42.96% between 700 m and 1100 m in both 8-year-old and 12-year-old plantations, respectively. However, no correlation was observed between the total soil C stocks and elevation in either age group of rubber plantations. Regardless of elevation gradient, the total ecosystem C stock of 12-year-old rubber plantations was 1.98% greater than that of 8-year-old rubber plantations. Biomass was the second largest contributor, while soil accounted for 82% to 90%, and the other factors contributed less than 2% of the total ecosystem C stock in both age groups. These fluctuations in C stocks along elevation gradients in both 8- and 12-year-old plantations suggested that rubber growth, biomass and C storage capacity decreased above 900 m and that age and elevation are key factors for biomass and C storage in monoculture rubber plantations.

This study proposes and validates a novel combustion control system for Oil-Fired Boilers aimed at reducing air pollutant emissions through flame image prediction. The proposed system is easily applicable to existing ships. Traditional proportional combustion control systems supply fuel and air at fixed ratios according to the set steam load, without considering the emission of air pollutants. To address this, a stable and immediate control system is proposed, which adjusts the air supply to modify the combustion state. The combustion control system utilizes oxygen concentration predictions from flame images via SEF+SVM as control inputs, and applies Internal Model Control (IMC)-based Proportional-Integral (PI) control for real-time combustion control. Due to the complexity of modeling the image-based system, IMC parameter tuning through experimentation is essential for achieving effective control performance. Experiments conducted on a 3000 kg/h marine oil-fired boiler in actual operation optimized the controller parameters for stability and responsiveness, and validated their effectiveness. The results demonstrate the potential of the proposed system to improve combustion efficiency and reduce emissions of air pollutants. This study provides a feasible and effective solution for enhancing the environmental performance of marine oil-fired boilers. Given its ease of application to existing ships, it is expected to contribute to sustainable air pollution reduction across the maritime environment.

Photovoltaic (PV) systems, which are renewable energy sources, are increasingly being utilized in distributed generation. To maintain a stable energy balance, energy storage systems such as batteries (BAT) play a vital role. Electric vehicles (EVs) offer a promising solution with rechargeable battery systems for operation. The BATs must maintain their state of charge within design boundaries, despite intermittent PV and load power fluctuations, and advanced power control and management techniques are essential for their effective operation. The article evaluates an intelligent controller that uses a Sliding Mode Control adaptive deep learning algorithm Convolutional Neural Networks (SMC-CNN) and a unique Strategy for managing supervisory power. (SPMS) for photovoltaic systems with battery energy storage for better regulation of DC bus voltage. SMC-CNN offers exceptional resilience and seamless functionality, minimizing fluctuations in DC bus voltage in the control strategy design requirements. The primary goals are maintaining a consistent power supply and ensuring continuous service by preventing system components from exceeding capacity. This study aims to enhance the control of DC bus voltage in the PV and battery system, with the primary significance focusing on the following aspects. The advanced SPMS has been created, incorporating control system constraints to enhance SOC balancing speed and reduce fluctuations in DC bus voltage. Power flow management involves optimizing energy flow between the PV system, battery system, and load while minimizing battery capacity requirements. The proposed SMC-CNN and SPMS are demonstrated through real-time simulation using Matlab/Simulink, as demonstrated in comprehensive case studies.

Commercial production of Choromytilus meridionalis (black mussel) and Mytilus galloprovincialis (Mediterranean mussel) contributes to half of the South African marine aquaculture production per year. However, limited ready-to-eat black mussel products are available. The aim of this preliminary study was to investigate the effects of storage (15 days at room temperature) on the total viable counts (TVC), coliforms, proximate composition, and fat oxidation (TBARS) of a small-scale kitchen-based ready-to-eat hot smoked black mussel product preserved with vegetable oil. Three batches of black mussel meat were smoked at 80ºC for 15 minutes. Half of each batch were packaged in sterile glass jars with heated (50ºC) vegetable oil and half without oil. Microbiological analyses were done at days 1, 3, 9 and 15. Proximate composition was determined at day 1 and TBARS at days 1 and 15. Coliforms for all samples throughout the storage period were undetected. TVC plates for mussels stored without oil had no growth at days 1 to 5, however, reached TVC > 5 log10.g-1 at day 15. TVC for mussels with oil increased from 0 at day 1 to > 5 log10.g-1 at day 3 and remained at counts > 5 log10.g-1. There was no significant difference (P > 0.05) in moisture, protein, and ash for mussels stored with oil and those without oil, while significant differences (P < 0.001) in total fat and carbohydrates (10.27 ± 2.10% and 6.80 ± 2.22% with oil, and 5.05 ± 1.49% and 10.59 ± 3.00% without oil) were detected. These differences were due to the presence of additional fats from the vegetable oil. TBARS at day 15 showed no significant difference (P > 0.05) between mussels stored with oil and those without oil. There were no significant differences in TBARS from day 1 to 15 for both oil and without oil. Small-scale kitchen-based smoked black mussels preserved without vegetable oil could be stored for up to 9 days at room temperature.

Heat transfer fluids are used in various industrial systems to maintain them in perfect operating conditions. Extensive research efforts have been dedicated to enhance the thermal properties of these heat transfer fluids to improve their efficiency. Developing nanofluids is a potential candidate for such enhancements. This study investigates the impact of incorporating TiO2 nanoparticles into two types of oils: transformer oil (NYTRO LIBRA) and virgin coconut oil (manufactured by Govi Aruna Pvt. Ltd.) at different temperatures and with varying volume fractions. The nanofluids were prepared using a two-step method by adding CTAB (Cetyltrimethylammonium bromide) surfactant. To minimize nanoparticle agglomeration, this study employed relatively low-volume fractions. Thermal properties by means of thermal conductivity, thermal diffusivity, and volumetric heat capacity were measured in accordance with ASTM (American Society for Testing and Materials) standard methods, using a multifunctional thermal conductivity meter (LAMBDA thermal conductivity meter). The measured thermal conductivity values were compared with theoretical models and previous research findings. It was confirmed that the modification of thermal properties was enhanced by doping TiO2 nanoparticles with different volume fraction.

Regular regimes of oil and oil products pipelines are studied. The problem is to develop an algorithm of effective pipeline system control that ensures the fulfillment of specified boundary conditions at the system boundaries. The product is pumped in batches, the flow is characterized by a change in temperature and pressure flow parameters over time. The developed solution method uses the principle of decomposition in the sense that each computational iteration is im-plemented in 3 stages, in three nested loops. The inner cycle is connected with the material bal-ance relations, at the next cycle the flow equations are introduced and the fulfillment of the 2nd Kirchhoff's law is monitored. If the flow process is significantly affected by temperature, then an external cycle is also implemented, correcting the solution so that the energy conservation equa-tion is satisfied. In the calculation procedure, some computational difficulties may arise, which consist in choosing an appropriate optimization method. On a specific example, the possibility of using various library programs to solve the problem was checked. The developed method is suita-ble for the analysis of systems of arbitrary topology. Since the method is not time-consuming, it can be recommended for online control of oil and oil products supply systems. The paper opens a new direction in the theory of hydraulic circuits. It uses both traditional methods of continuum mechanics and stochastic models.

While the demand in reduction of CO₂ increases, the need for CO₂ sequestration processes is very high. One promising technology is the Carbon Capture and Storage (CCS). In this paper we refer to several papers which study the three main steps in CCS chain. CO₂ capture technologies, CO₂ transportation to the storage sites and the very critical step the CO₂ storage. Recently a novel method (mineral carbonation) for CO₂ sequestration has been proposed which is based in the reaction of CO₂ with calcium or magnesium oxides or hydroxides to form stable carbonate materials. Greece is a country that emits CO₂ mainly from the lignite fired power plant in Western Greece. After the study of the bibliographic references about the use of mineral carbonation process while injecting CO₂ in the appropriate geological forms we concluded that there are also these forms in our country and mainly in the area near to the power plant such as in sites Vourinos and Pindos. In these sites exist minerals rich in oxides and hydroxides of Ca, Mg and Fe representing the perfect materials for mineral carbonation.

The antimicrobial resistance to clinically approved antibiotics is rapidly increasing worldwide. Staphylococcus aureus is a critical contributor to deaths associated with antibiotic resistance. In this regard, the search for natural compounds is quite active, that alone or in combination with other agents can be effective as new antibacterial agents. The antibacterial activity of essential oils has presented an increasing interest during the last years and was effective even on multidrug-resistant strains. The present study aims to investigate the interaction effects of oregano essential oil (OEO) with some conventional antibiotics against Staphylococcus aureus tested by agar methods. For this purpose, we selected S. aureus ATCC 29213 and five clinical isolates representative of the species. The essential oil was analyzed using gas chromatography coupled with mass spectrometry (GC-MS). The analysis of the Oregano essential oil revealed the main component to be carvacrol (81,20%). Concentration 2.5% (v/v) OEO was combined with drugs proposed by EUCAST, 2024, specifically penicillin, cefoxitin, erythromycin, gentamycin and tetracycline. The research results showed that the combination of OEO with penicillin, cefoxitin, erythromycin, and tetracycline enhanced the antimicrobial activity of the antibiotics against S. aureus in almost all cases. The area of suppression remained identical (but not smaller) in the unaffected cases. When comparing the effects of the GEN-OEO combination and GEN against most S. aureus strains, a decrease in antimicrobial activity was reported by the diffusion agar method.

The process model is very essential for the model based control design. The model of the process can be identified using system identification algorithm. The system identification is done through the open loop and closed loop approaches. In this work, the lab scale conical tank setup configured as a non square MIMO system. The conical tank system is identified through the both appraoches, the effectiveness and need of the both approaces are discussed. Based on the open loop identified model the controller designed and the controller implemented in the real time the to record the process data. From this data the closed loop identification are conducted uisng N4SID algorithm. The controller seetings are obtained using the smith predcitor based IMC based PI controller for the obtained model. The proposed identification algorithm and controller tuning show the better reults over the conventional method. Moreover, this method is applicable for all the non square MIMO system.

Sesame seeds and their edible oil are highly nutritious and rich in mono- and polyunsaturated fatty acids. Bioactive compounds such as sterols, tocopherols, and sesamol provide significant medicinal benefits. The high oil content (50%) and favorable mono-and polyunsaturated fatty acids balance, as well as sesame's resilience to water stress makes, make it a promising candidate for global agricultural expansion. However, sesame production faces challenges such as low yields, poor response to agricultural inputs, and losses due to capsule dehiscence. To enhance yield, traits like determinate growth, dwarfism, high harvest index, non-shattering capsules, and photoperiod sensitivity are needed. These traits can be achieved through variation or induced mutation breeding. Traditional breeding methods often result in unwanted genetic changes. The CRISPR/Cas9 technology has the potential to suppress detrimental alleles and improve the fatty acid profile by inhibiting polyunsaturated fatty acid biosynthesis. Even though sesame is an orphan crop, it has entered the genomic era, with available sequences assisting molecular breeding efforts. This progress aids in associating single nucleotide polymorphisms (SNPs) and simple sequence repeats (SSRs) with key economic traits, as well as identifying genes related to adaptability, oil production, fatty acid synthesis, and photosynthesis. Additionally, transcriptomic studies can reveal genes involved in abiotic stress responses and adaptation to diverse climates. Quantitative trait loci (QTL) mapping can identify loci linked to crucial traits such as capsule size, seed count per capsule, and capsule number per plant. This paper reviews recent advances in sesame breeding, discusses ongoing challenges, and explores potential strategies for future improvement. Hence, integrating advanced genomic tools and breeding strategies provides promising ways to enhance sesame production to meet global demands.

Most systems that are the subject of control engineering studies have some non-linearity. An example of this is the horizontal cylindrical tank, commonly used in process industries. To deal with cases like this, several control theories have been developed over time, each one presenting better results in certain systems. This work presents an alternative for the control of nonlinear systems, without necessary modeling or previous information about the system, based on a new optimization law for the artificial neural network training in real time.

Erigeron floribundus (Asteraceae) is an herbaceous plant widely used in the Cameroonian traditional medicine to treat various diseases of microbial and non-microbial origin. In the present study we evaluated the in vitro biological activities displayed by the essential oil obtained from the aerial parts of E. floribundus, namely the antioxidant, antimicrobial and antiproliferative activities. Moreover, we investigated the inhibitory effects of E. floribundus essential oil on nicotinate mononucleotide adenylyltransferase (NadD), a promising new target for developing novel antibiotics, and Trypanosoma brucei, the protozoan parasite responsible for Human African trypanosomiasis. The essential oil composition was dominated by spathulenol (12.2%), caryophyllene oxide (12.4%) and limonene (8.8%). The E. floribundus oil showed a good activity against Staphylococcus aureus (IZD of 14 mm, MIC of 512 µg/mL). Interestingly, it inhibited the NadD enzyme from S. aureus (IC50 of 98 µg/mL), with no effects on mammalian orthologue enzymes. In addition, T. brucei proliferation was inhibited with IC50 values of 33.5 µg/mL with the essential oil and 5.6 µg/mL with the active component limonene. The essential oil exhibited strong cytotoxicity on HCT 116 colon carcinoma cells with an IC50 value of 14.89 µg/mL, and remarkable ferric reducing antioxidant power (TEAC= 411.9 μmol TE/g).

Qatar and other Gulf States have a diverse range of marine vegetation that is adapted to the stressful environmental conditions of seawater. The industrial wastewater produced by oil and gas activities adds further detrimental conditions for marine aquatic photosynthetic organ-isms on the Qatari coastlines. Thus, these organisms experience severe stress from both seawater and industrial wastewater. This review discusses the biodiversity in seawater around Qatar, as well as remediation methods and metabolic pathways to reduce the negative impacts of heavy metals and petroleum hydrocarbons produced during these activities. These methods include phyto-stabilization phyto-accumulation, phyto-volatilization, and phyto-degradation. Phy-to-degradation in particular is discussed in detail, including metabolic pathways such as alkane and aromatic-compound degradation pathways. The role of microorganisms that are adjacent to or associated with these aquatic marine organisms is discussed, including rhizosphere biodeg-radation. In this type of biodegradation, exudates are released by plant roots and supply nutrients to microorganisms in the rhizosphere, which enhances their ability to degrade organic pollutants. Special attention is paid to mangrove forests and their roles in remediating shores polluted by industrial wastewater. Seagrasses (Halodule uninervis, Halophila ovalis, and Thalassia hemprichii) and seaweeds (Chlorophyta, Phaeophyta, and Rhodophyta) around the peninsula of Qatar are also discussed.

Epigallocatechin gallate (EGCG), the principal catechin in green tea, exhibits diverse therapeutic properties. However, its clinical efficacy is hindered by poor stability and low bioavailability. This study investigated solid particle-in-oil-in-water (S/O/W) emulsions stabilized by whey protein isolate (WPI) and sodium caseinate (NaCas) as carriers to enhance the bioavailability and intestinal absorption of EGCG. Molecular docking revealed binding interactions between EGCG and these macromolecules. The emulsions exhibited high encapsulation efficiencies and augmented EGCG bioaccessibility by 64% compared to free EGCG in a simulated gastrointestinal digestion model. EGCG-loaded emulsions demonstrated minimal cytotoxicity towards Caco-2 cells and facilitated EGCG transport across the intestinal epithelial layer without compromising tight junction integrity. Notably, EGCG-loaded emulsions protected Caco-2 cells against oxidative stress by suppressing intracellular reactive oxygen species generation. The results demonstrate the potential of WPI- and NaCas-stabilized S/O/W emulsions to enhance the bioavailability, intestinal absorption, and bioactivity of EGCG, expanding its applications in functional foods and nutraceuticals.

This article explores the cutting-edge advancement of gypsum and cement building boards infused with shape-stabilized n-octadecane, an organic phase change material (PCM). The primary focus is on improving energy efficiency and providing electromagnetic interference (EMI) shielding capabilities for contemporary buildings. The research investigates the integration of these materials into construction materials, using red-mud Carbon Foam as a stabilizer for n-octadecane (OD@CCF). Various analyses, including microstructural examination, porosity assessment, and additive dispersion, were conducted using X-ray microtomography and density measurements. Thermal conductivity measurements demonstrated the enhancement of composite boards as the OD@CCF content increased, while mechanical tests indicated an optimal additive content of up to 20%. The thermal-regulated capabilities of these advanced panels were evaluated in a custom-designed room model equipped with a homemade environmental chamber, illustrating a consistent temperature environment during heating and cooling cycles. The incorporation of OD@CCF into cement boards exhibited improved thermal energy storage properties. Moreover, the examined composite boards displayed efficient electromagnetic shielding performance within the frequency range of 3.2–7.0 GHz, achieving EMI values of approximately 18 and 19.5 dB for gypsum and cement boards, respectively, meeting the entry-level value required for commercial applications.

The paper presents a conceptual model of the route of macroplastic debris (5 > mm) through a fluvial system, which can support future works on the overlooked processes of macroplastic storage and remobilization in rivers. We divided the macroplastic route into (1) input, (2) transport, (3) storage, (4) remobilization and (5) output phases. Phase 1 is mainly controlled by humans, phases 2–4 by fluvial processes, and phase 5 by both types of controls. We hypothesize that natural characteristics of fluvial systems and their modification by dam reservoirs and flood embankments construction are key controls on macroplastic storage and remobilization in rivers. The zone of macroplastic storage can be defined as a river floodplain inundated since the beginning of widespread disposal of plastic waste to the environment in the 1960s and remobilization zone as a part of the storage zone influenced by floodwaters and bank erosion. The amount of macroplastic in both zones can be estimated using data on the abundance of surface- and subsurface-stored macroplastic and the lateral and vertical extent of the zones. Our model creates the framework for estimation of how much plastic has accumulated in rivers and will be present in future riverscapes.

In this research, catalytic steam reforming acetic acid derived from the aqueous portion of bio-oil for hydrogen production was investigated by using different Ni/ATC (Attapulgite Clay) catalysts prepared by precipitation, impregnation and mechanical blending methods. The fresh and reduced catalysts were characterized by XRD, N₂ adsorption-desorption, TEM and H₂-TPR. The comprehensive results demonstrated that the interaction between active metallic Ni and ATC carrier was significantly improved in Ni/ATC catalyst prepared by precipitation method, and in which the mean Ni particle size was the smallest (~13 nm) resulted in the highest metal dispersion (7.5%). The catalytic performance of the three catalysts was evaluated through the process of steam reforming of acetic acid in a fixed-bed reactor under atmospheric pressure at two different temperatures, such as 550 ℃ and 650 ℃. Results showed that the Ni/ATC (PM-N/ATC) prepared by precipitation method, achieved the highest H₂ yield of ~82% and little lower acetic acid conversion efficiency of ~85% than that (~95%) of Ni/ATC (IM-NATC) prepared by impregnation method. In addition, the deactivation catalysts after reaction for 4 h were analyzed by XRD, TGA-DTG and TEM, which demonstrated that the catalyst deactivation was not caused by the amount of carbon deposition, but owed to the significant agglomeration and sintering of Ni particles in the carrier.

Enhancing the management and monitoring of oil and gas processes demands developing precise predictive analytics techniques. Over the past two years, oil and its prediction have advanced significantly using conventional and modern Machine Learning techniques. Several review articles detail the developments in predictive maintenance and technical and non-technical aspects of influencing the uptake of big data. The absence of references for machine learning techniques impacts the effective optimization of predictive analytics in the oil and gas sector. This review paper offers readers thorough information on the latest machine learning methods utilized in this industry's predictive analytical modelling. The review covers forms of Machine Learning techniques used in predictive analytic modelling from 2021 to 2023 (91 articles). It provides an overview of the details of the papers that were reviewed, comprising of the model’s categories, the data's temporality, field, and name, the dataset's type, predictive analytics (classification or clustering or prediction), the models' input and output parameters, performance metrics, optimal model, and benefits and its drawbacks. Additionally, suggestions for future research directions are provided to raise the potential of the associated knowledge and increase the accuracy of oil and gas predictive analytics models.

Silver ion (Ag+) are recognized for their potent antibacterial properties; however, their utilization in food preservation is restricted by factors such as inadequate stability, a transient antibacterial impact, and the potential for human absorption. Hydrogel-based antibacterial agents are capable of exerting their antibacterial effects by establishing appropriate microenvironments, which facilitate the efficient delivery of antimicrobial molecules to the contaminated regions of food. In previous studies, we observed that chitosan (CS) and silver nitrate (AgNO3) were able to reduce Ag+ to silver nanoparticles (AgNPs) with enhanced antibacterial properties. This not only significantly extended the stability of the antibacterial agent but also demonstrated exceptional inhibitory capabilities against pathogenic bacteria, including common grape contaminants such as P. expansum, A. niger, and B. cinerea. Utilizing ultrasound-induced complexation technology, this study has successfully synthesized a chitosan-silver (CS-AgNPs) hydrogel. The efficacy of this hydrogel against the pathogenic fungus responsible for jujube black spot disease has been thoroughly investigated. The morphology structures of CS-AgNPs hydrogels were characterized by TEM, FTIR and UV-vis. The results indicated that AgNPs ranging from 80 to 110 nm were uniformly dispersed within the gel matrix and remained stable for extended periods at room temperature. In vitro antibacterial assays and fractional inhibitory concentration index (FICI) studies revealed that the pronounced antibacterial efficacy of the CS-AgNPs hydrogel was primarily attributed to the additive antibacterial effect of CS and AgNPs. These insights underscore the significant potential of CS-AgNPs hydrogels in combating fungal diseases of jujube, offering innovative strategies and materials for the management of agricultural pathogens.

Hydrogen storage in high pressure tanks can occur with different filling strategies. Many studies have been carried out on supplies with increasing pressure rates. However, hydrogen filling with constant mass inflow rate have not received the same attention. The present work aims to carry out numerical simulations to study hydrogen flow, in a type 3 tank of 70 MPa NWP and constant inflow rate condition. From the analysis of the results, it was possible to verify that there is a linear relationship between the increase in the total equilibrium temperature and the final hydrogen temperature. There is also a linear increasing relationship between Inlet and final temperatures when the equilibrium temperature is fixed. Considering fully adiabatic walls results in significant increases in temperature. The difference between total and static temperatures found in the Inlet tube decreases with the decrease in mass flow rate. The choice of a polymer for the tank lining led to higher temperatures when compared to an aluminum lining.

Pipelines extend thousands of kilometers to transport and distribute oil and gas. Given the challenges often faced with corrosion, fatigue, and other issues on steel pipes, the demand for glass fiber reinforced plastics (GFRP) pipes is increasing in the oil and gas gathering and transmission systems. However, the medium transported through these pipelines contains multiple acid gases such as CO2 and H2S, as well as ions including Cl-、Ca2+、Mg2+、SO42-、CO32- and HCO3-. These substances can cause a series of problems, such as aging, debonding, delamination, and fracture. In this study, a series of aging damage experiments were conducted on V-shaped GFRP pipes with depths of 2mm and 5mm. The aging and failure of GFRP were studied under the combined effects of external force and acidic solution using acoustic emission (AE) techniques. It was found that the acidic aging solution promoted matrix damage, fiber/matrix desorption, and delamination damage in GFRP pipes over a short period. However, the overall aging effect was relatively weak. Based on the experimental data, the SSA-LSSVM algorithm was proposed and applied to the damage pattern recognition of GFRP. An average recognition rate of up to 90% was achieved, indicating that this method is highly suitable for analyzing AE signals related to GFRP damage.

.Various synthetic nematicides are currently used effectively in the control of plant parasitic nematodes. However, these nematicides have adverse effects on humans and the environment. Neem oil is eco-friendly alternatives to synthetic nematicides. The effectiveness of repeated neem oil application in suppressing the root-knot nematodes infestation in figs seedlings was therefore examined in this study, both in its natural form (10 ml/L) and in its nano-emulsion form (5 and 7 ml/L). The recorded reduction parameters of M. incognita were J2/250g soil, galls and egg masses / 5g roots of infected fig seedlings were measured at that time, and the effects of these natural additives were compared with the Fosthiazate (Krenkel 75%EC). The impact of such soil amendments on some typical plant parameters, the total microbial count of soil, and the overall enzymatic activity of the fig rhizosphere were also included. Obtained results revealed that the soil population density of root knot nematode suppressed by 80.3% , reduction of nematode egg masses (60.4%) due to the application of nano-emulsion of neem oil (at 7ml/L). Present work recommend the use of nano-emulsion of neem oil as one of the effective and eco-friendly means to reduce the root- knot nematode on fig .

Groundwater is becoming increasingly important in the Pacific Northwest of the USA due to declining snowpack volumes and shifts in precipitation type and timing, all connected with climate change. The Upper Williamson Basin of the Klamath Watershed is a groundwater dominated watershed with massive fluctuations in year-to-year streamflow volumes over the past four decades, including the complete absence of any live flow for several years. The precise relationship between groundwater and streamflow in the basin has been difficult to assess due to a limited number of monitoring wells and significant gaps in the water level time history. To address this challenge, we use a novel imputation technique that leverages Earth observations and machine learning to impute gaps in water level records. We use these more complete datasets to compute a groundwater storage change time series for the basin. We show that groundwater storage is highly correlated to streamflow and that groundwater storage is correlated to rainfall with a three- to four-year delay that appears variable depending on groundwater storage volumes. The tools and relationships we present make it possible for water managers to estimate when streamflows will return to the basin and be more informed to support better management.

Public key encryption methods are often used to create a digital signature, and where Bob has a public key and a private key. In order to prove his identity, he will encrypt something related to the message with his private key, and which can then be checked with his public key. The main current methods of public-key encryption include RSA and ECC (Elliptic Curve Cryptography), and which involve computationally difficult operations. But these operations have not been proven to be hard in an era of quantum computers. One well-known hard problem is the solving of quadratic equations with $m$ equations with $n$ variables. This is a known NP-hard problem, even in a world of quantum computers. These can be used as post-quantum signature schemes and which involve multivariate equations. In order to understand these methods, this paper outlines a simple example of implementing the oil and vinegar method, and where we have a number of unknown oil variables and a number of known vinegar variables, and where the vinegar variables help convert the hard problem into an easy one.

This study aimed to determine whether camelina oil is safe for use in canine diets, using canola oil and flax oil as controls as they are similar and generally regarded as safe (GRAS) for canine diets. Thirty privately-owned adult dogs of various breeds (17 females; 13 males), with an average age of 7.2 ± 3.1 years (mean ± SD) and body weight (BW) of 27.4 ± 14.0 were used. After a 4-week wash-in period using sunflower oil and kibble, dogs were blocked by breed, age, and size, and randomly allocated to one of three treatment oils (camelina (CAM), flax (FLX), or canola (OLA)) at a level of 8.2 g oil/100g total dietary intake. Body condition score (BCS), BW, food intake (FI), and hematological and select biochemical parameters were measured at various timepoints over a 16-week feeding period. All data were analyzed with ANOVA using PROC GLIMMIX of SAS. No biologically significant differences were seen between treatment groups for BW, BCS, FI, hematological and biochemical results. Statistically significant differences noted among some serum biochemical results were considered small and due to normal biological variation. These results support a conclusion that camelina oil is safe for use in canine nutrition.

Abstract: This work is presenting a water level control and monitoring system in a tank, by using the development boards Arduino Uno, NodeMCU ESP8266 and the ultrasonic sensor HC-SR04. The water tank is supplied through a pump controlled by the development board Arduino Uno by means of a relay. The author has issued a control algorithm for controlling the water level and a program in the development environment Arduino IDE that has been implemented and validated on the experimental stand. For monitoring the development board NodeMCU ESP8266 has been used that takes the information from the ultrasonic sensor HC-SR04 and sends it through Wi-Fi to the platform ThingSpeak. Based on the experimental results it has been found out that the water level control system in the tank provides the performances imposed through the designing stage, and the pump running has been automatically stopped when the limit, settled through the program for the water maximum level in the tank, has been reached. The measured value of the water level is shown on the LCD 1602 display. In the water circuit of the home consumers or irrigation systems supplied from the tank a pump controlled by means of a mobile phone has been installed. In order to implement this control system, the author has issued a program for another development board Arduino Uno, whilst for the mobile phone he used the application Arduino Bluetooth Control. The advantage of this water level control and monitoring system in the tank is given by the very low costs in comparison to the cost of an industrial type control system.

Counter-current spontaneous imbibition of water is a critical oil-recovery mechanism. In the laboratory, the Amott test is a widely used technique to assess efficacy of brine imbibition into oil-saturated core plugs. The classic Amott-cell methodology was designed to estimate ultimate oil recovery, but not the recovery dynamics that provides essential information about the imbibition mechanisms. Retention of oil droplets at the external core surface and delayed onset of oil production are the two key artifacts of the classic Amott experiment. This retention, referred to here as the ``external-surface oil holdup effect'', often results in stepwise recovery curves that obscure true dynamics of spontaneous imbibition. To address these holdup drawbacks of the classic Amott method, we modified the Amott cell and experimental procedure. For the first time, using water-wet Indiana limestone cores saturated with brine and mineral oil, we showed that our improvements of the Amott method enabled accurate and reproducible measurements of oil-recovery dynamics. We used the Generalized Extreme Value (GEV) statistics to describe oil-production histories from water-wet heterogeneous limestone cores with finite initial water saturations, for the first time. We demonstrated that our four-parameter GEV model accurately described the recovery dynamics, and that optimal GEV parameter values systematically reflected the key characteristics of the oil-rock system, such as oil viscosity and rock permeability. These findings gave us a more fundamental understanding of spontaneous, counter-current imbibition mechanisms and insights into what constitutes a predictive model of counter-current water imbibition into oil-saturated rocks with finite initial water saturation.

In order to study the adsorption process and adsorption characteristics of shale oil at the macro scale, the isothermal adsorption experiments of illite and kerogen on heptadecane (oil phase) solution were carried out by infrared spectrophotometry and gas chromatography-mass spectrometry. The reaction mechanism of alkane solution concentration and temperature in the adsorption process was investigated. The adsorption characteristics of heptadecane on the surface and pores of illite and kerogen were elucidated by adsorption isotherm model and adsorption thermodynamic model. The results show that: The concentration of alkane solution contributes to the adsorption of illite and kerogen. As the concentration of the solution continues to increase, the adsorption rate gradually slows down. However, the temperature hardly affects the adsorption rate. At 25℃, 50℃ and 60℃, the adsorption process of illite on alkane solution is more consistent with Langmuir model and Freundlich model, respectively. The difference is that Langmuir model is suitable for describing the whole adsorption process of kerogen on alkane solution. 3) The adsorption process of illite and kerogen to heptadecane solution is an endothermic reaction. Heating helps to accelerate the migration rate of alkanes, which is conducive to the adsorption reaction. The research results clarify the adsorption characteristics of shale oil heavy components from the macro level, and fill the research gap in the application of solid-liquid isothermal adsorption physical experiments to the adsorption and occurrence of shale oil.