One of the primary causes of the mechanical seal failure is rotor vibration. Traditional dynamic seal models often would not be able to fully explaining the failure mechanisms. The seal dynamic models proposed in this paper, including those developed by the authors, prove valuable in predicting seal dynamics during operation in specific turbomachinery and in explaining the causes of seal failure. The single-mass dynamic model is suitable for analyzing contact mechanical seal and simple design dry gas seals dynamics. The two-mass dynamic model is used for investigating operational dynamics processes in classical dry gas seals under complex loading conditions. The three-mass dynamic model is used to study various complex mechanical seal types. This model is able to determine the normal operating condition range and to explain leakage mechanisms in the presence of excessive rotor vibrations.

In eastern part of Ethiopia groundnut is very commonly intercropped with sorghum. Even though intercropping of sorghum with groundnut is practiced in the eastern part of Ethiopia the population density at what ratio should not be known. Therefore determining the population ratio is found to be crucial to draw management options. The study was conducted at two locations at Fadis (on station) and Babile (sub- station). Sorghum variety (Teshale) and groundnut (Fetene) were used as planting materials. All agronomic data were collected and analyzed by using GenStat software. Significant different were obtained among the treatments. The research result showed that, there were significance difference for both sorghum and ground nut yield per hectare in the years (2014 and 2015) among treatments. The result over time(in 2014 and 2015) at Fadis and Erer showed that the highest sorghum and groundnut yield per hectare were obtained/harvested from the intra row spacing of 25cmx20cm and 30cmx20cm intercropping sorghum with ground nut system with (1.27 and 1.31) respectively. The highest LER (1.31) and highest GMV (10218.00 ETBr/ha) were obtained from the intercropping of 30cmx20cm (Sorghum & groundnut). Clearly showed that, with intercropping of sorghum and Groundnut, it is possible to produce additional yield of sorghum without significant reduction in groundnut yield. As a result of this, the intra spacing of the main crop (sorghum) 25cm and 30cm and for the subsidiary crop (groundnut) 20cm was recommended for further production in the study areas of eastern Harerghe zone and similar agro-ecologies.

In the drive towards environmental restoration and sustainable energy solutions, effective utilization and management of agricultural crop residues are vital to mitigate greenhouse gas (GHG) emissions and waste accumulation. Converting biogenic wastes into biofuels and bioproducts has the potential to tackle the energy crisis and contribute to environmental remediation. In this investigation, teff husk, primarily generated in Ethiopia during teff production within the agro-industrial sector, is used as the feedstock for the slow pyrolysis process. In Ethiopia, it is estimated that over 1.75 million tons of teff husk are generated annually, with a significant portion being incinerated in the fields, resulting in substantial environmental pollution. This study focuses on assessing teff husk as a potential material for slow pyrolysis, a crucial stage in biochar production, to tap into its biochar-producing potential. To determine the composition of the biomass, the teff-husk was initially analyzed by thermogravimetry. The significant presence of fixed carbon indicates that teff husk is a viable candidate for pyrolytic conversion into biochar particles. The process of slow pyrolysis took place at three varied temperatures—specifically, at 400, 450, and 500 °C. Process parameters of slow pyrolysis such as reaction time, temperature, and heating rate were enhanced to obtain maximum biochar yields. The highest biochar yield of 43.4 wt% was recorded at optimized reaction time, temperature, and heating rate of 120 min, 400 °C, and 4.2 °C/min, respectively. Furthermore, biochar's physicochemical, SEM-EDX, FTIR, and TGA characterization were performed. The thermal stability and carbon content of biochar were found to rise at higher temperatures. Unlike fuel recovery, the results suggest that teff-husk can be used as a feedstock for biochar production.

Accurate assessment of shale gas reserves hinges on a detailed characterization of gas and water distribution within shale reservoirs. Despite its importance, the nanoscale behavior of water and methane in deep shale formations, especially under elevated temperatures and pressures, remains poorly understood. This study proposes a novel molecular modeling approach to represent the complex nanocomposite porous media found in deep shale matrices. Leveraging quantitative data from experimental analyses of shale pore composition, we developed a molecular model that accurately reflects the intricate pore-slit structure within a composite of kerogen and illite, common constituents of shale. Employing a hybrid grand canonical Monte Carlo and molecular dynamics simulation technique, we investigated the micro-scale distribution and preferential adsorption sites of water and methane within the shale matrix. Our research further elucidates the impact of water on the pore structure of shale and delineates the co-occurrence patterns of water and methane. The simulations reveal that water and methane share similar adsorption preferences on kerogen surfaces, while methane does not exhibit specific adsorption preferences on water-bearing illite. We also find that the presence of water significantly alters the illite pore space, leading to a reduction in larger pore volumes and a concomitant increase in smaller pores. The decrease in methane content with increasing water content is more pronounced in the shrinkage cracks compared to the kerogen matrix pores and is particularly notable in the macropores of illite. The findings underscore the differential sensitivity of methane content to water levels across various shale pore types. These insights contribute to a deeper theoretical understanding of gas and water distribution mechanisms in deep shale reservoirs, offering valuable support for the evaluation of deep shale gas resource potential.

: This study focuses on optimizing chlorophyll extraction techniques and strategically placing leaf disks to enhance chlorophyll concentration in sesame (Sesamum indicum L.) leaves. Thirty sesame genotypes, categorized into light green (LG), middle green (MG), and deep green (DG) pigment groups based on leaf coloration, were selected from a larger pool of field-grown accessions. The investigation involved determining optimal SPAD value index measurements, quantifying pigment concentrations, exploring extraction solvents, and selecting suitable leaf disk positions. Significant variations in chlorophyll content were observed across genotypes, greenness categories, and leaf disk positions. The categorization of genotypes into DG, MG, and LG groups revealed a correlation between leaf appearance and chlorophyll content. The study highlighted a consistent relationship between carotenoids and chlorophyll, indicating their role in adaptation to warm environments. Examination of leaf disk positions revealed a significant chlorophyll gradient along the leaf blade, emphasizing the need for standardized protocols. Chlorophyll extraction experiments identified DMSO and 96% ethanol, particularly the later incubated for 10 minutes at 85°C, as effective choices. This recommendation considers factors like cost-effectiveness, time efficiency, safety, and environmental regulations, ensuring consistent and simplified extraction processes. For higher chlorophyll extraction, focusing on leaf tips and the 75% position along the sesame leaf blade is suggested, consistently yielding higher chlorophyll content. Our findings therefore, underscores insightful knowledge on chlorophyll gradients and encouraging for standardized protocols, that enabling researchers to refine experimental designs for precise and comparable chlorophyll measurements. Recommended solvent choices ensure reliable outcomes in plant physiology, ecology, and environmental studies.

Carbon dioxide (CO2)miscible fracturing huff and puff technology plays a pivotal role in enhancing the recovery rate of crude oil, particularly in reservoirs with challenging physical properties, strong water sensitivity, high injection pressure, and complex water injection dynamics. In this study, the oil-increasing mechanism and huff and puff effect of CO2 miscible fracturing fluid are investigated through a comprehensive experimental approach. Specifically, experiments on PVT gas injection expansion, minimum miscible pressure, and CO2 miscible fracturing huff and puff are conducted on the G fault block reservoir in J Oilfield. The findings demonstrate that injecting CO2 into reservoirs leads to oil volume expansion, viscosity reduction, and saturation pressure increase. Additionally, the inclusion of solubilizers and viscosity reducers further enhances the efficiency of crude oil extraction. Solubilizers not only improve oil recovery but also reduce the minimum miscible pressure required for effective CO2 dispersion. Furthermore, the shut-in time, permeability, and huff and puff method all have considerable impacts on huff and puff recovery rate. This study offers valuable technical insights, supporting the application of CO2 miscible fracturing huff and puff technology to enhance oil recovery in low-permeability reservoirs.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

Improper disposal of waste plastic has caused serious ecological and environmental pollution problems. Transforming plastics into high value-added chemicals can not only achieve efficient recycling of waste plastics, but also an effective way to control white pollution. The catalyst selectively breaks the C-C bond of polyolefin plastic under heat treatment and converts it into liquid fuel, thus realizing sustainable recycling of plastics and has a good development prospect. This review provides a detailed overview of the current development of catalytic pyrolysis, catalytic hydrolysis, solvent decomposition and supercritical hydrothermal liquefaction for cracking plastics to make fuel oil. The reaction mechanism, influencing factors and promoting effects of catalysts in various degradation technologies are analyzed and summarized and the latest proposed tandem reaction for degrading plastics is briefly introduced. Finally, some optimization paths of waste plastic pyrolysis to fuel oil technology are proposed: synergies between mixed raw materials, in-depth exploration of catalysts, design and manufacture of reactors that match the pyrolysis technology. All these are important research directions for promoting the industrialization of plastic pyrolysis to fuel oil.

Solvent free copolymerization of epoxides derived from fatty acid esters of waste cooking oil with phthalic anhydride using (salen)CrIII Cl as catalyst and n-Bu4NCl/DMAP as co-catalyst was carried out for the first time under microwave irradiation, where reaction time was reduced from number of hours to minutes. The polyesters were obtained with molecular weight (Mw = 3084-6740 g/mol) and dispersity values (D = 1.18-1.92), when (salen)CrIII Cl/n-Bu4NCl was used as catalysts. While in case of DMAP as a co-catalyst, polyesters with improved molecular weight (Mw = 5537-6925 g/mol) and narrow dispersity values (D = 1.07-1.28) were obtained even at reduced concentrations of (salen)CrIII Cl and DMAP. The obtained products were characterized and evaluated by attenuated total reflection-fourier transform infrared spectroscopy (ATR-FTIR), proton nuclear magnetic resonance (1H-NMR) spectroscopy, gel permeation chromatography (GPC) and thermogravimetric analysis (TGA) Techniques.

Superior fiber quality is one of the most important objectives in cotton breeding. To detect the genetic basis underlying fiber quality, an F2 population containing 413 plants was constructed by crossing Jifeng 914 and Jifeng 173, both of which have superior fiber quality, with Jifeng 173 being better. Five fiber quality traits were investigated in the F2, F2:3, F2:4, and F2:5 populations. Quantitative trait loci (QTL) mapping was conducted based on a high-density genetic map containing 11,488 single nucleotide polymorphisms (SNPs) and spanning 4,202.12 cM in length. Transgressive segregation patterns and complex correlations in the five tested traits were observed. A total of 108 QTLs were found, including 27 for fiber length (FL), 16 for fiber strength (FS), 24 for micronaire (MC), 17 for fiber uniformity (FU), and 24 for fiber elongation rate (FE). Chromosome A7 contained 12 QTL, ranking the first. No QTL was found on chromosome D1 and D11. Each QTL contributed 1.98%–21.45% to the phenotypic variation (PV), including 13 major effect QTLs that contributed more than 10% toward PV. Two QTLs could be repeatedly detected in three populations, including qFL-D3-2 in F2, F2:4, and F2:5 with 9.18%–21.45% of PV, qFS-A11-1 in F2:3, F2:4 and F2:5 with 6.05%–10.41% of PV. Another seven stable QTLs could be detected in two populations, including four major effect QTLs: qFL-A12-3, qFS-D10-2, qMC-D6-2, and qMC-D8-1. Fourteen QTL-overlapping regions were found, which might explain the complex correlations among the five phenotypic traits. Four regions on chromosome A11, D3, D6, and D10 covered by both stable and major effect QTLs are promising for further fine mapping. The genomic regions of the two QTLs detected in three populations and the four major effect QTLs contain 810 genes. Gene functional analysis revealed that the annotated genes are mainly involved in protein binding and metabolic pathways. Fifteen candidate genes in the qFL-D3-2 region are highly expressed in fiber or ovules during fiber initiation, elongation, secondary cell wall thickening, or maturation stages. qRT-PCR revealed that Ghir_D03G005440.1 and Ghir_D03G011310.1 may play a role in promoting fiber initiation, Ghir_D03G006470.1 may be beneficial for promoting fiber elongation. This study provides more information for revealing the molecular genetic basis underlying cotton fiber quality.

This study aims to investigate the interfacial tension, emulsion stability, and the impact on oil displacement effectiveness of mixed systems containing nonionic surfactants and amphoteric surfactants at different ratios. To achieve this, three different emulsion stability formulations were prepared by mixing betaine and nonionic surfactants in ratios of 1:1, 3:2, and 3:1 respectively. By adjusting the proportions of betaine and nonionic surfactants, variations in interfacial tension and emulsion formation among the three mixed systems were studied to analyze the mechanism of interaction between betaine and nonionic surfactants and evaluate their effects on crude oil displacement and enhanced oil recovery in reservoirs. Subsequently, microscopic and macroscopic oil displacement experiments were conducted on the three mixed systems, along with experiments on emulsion flow resistance. The aim was to verify the oil displacement effectiveness of different mixed systems and further understand their potential applications in reservoirs. By comprehensively analyzing the experimental results, optimal ratios and conditions for the mixed systems were determined. The experimental results indicate that the emulsification system formed by mixing betaine and nonionic surfactants at a ratio of 3:1 achieves molecular synergies through electrostatic interactions and mixed adsorption with betaine, resulting in a compact arrangement of interface membranes and demonstrating a synergistic effect in reducing interfacial tension to an ultra-low value of 10 -4 mN/m. Additionally, as the proportion of betaine surfactant increases, the viscosity of the aqueous phase liquid film increases, the rate of thinning of the liquid film slows down, the rate of water release slows down, and the stability of the emulsion increases. Microscopic oil displacement experiments verified that the three mixed systems increase oil washing efficiency through low interfacial tension and emulsification stripping action, thereby increasing the oil displacement mechanism's coefficient. Emulsion flow resistance experiments demonstrated that as the proportion of betaine surfactant increases, the system exhibits better plugging ability. However, macroscopic oil displacement experiments revealed differences in compatibility between different emulsion stability solutions and rocks with different permeabilities. The mixed system of betaine and nonionic surfactants at a ratio of 3:1 exhibits the best emulsification plugging ability in rocks with a permeability of 109mD, while the 1:1 mixed system performs best in rocks with a permeability of 12mD. This holds significant theoretical and practical significance for reservoir development and enhanced production.

Asphaltene-resin-paraffin deposition (ARPD) is a complicated and prevalent issue in oil and gas industry, impacting the efficiency, integrity of petroleum extraction, production, transportation and processing systems. Considering all witnessed ARPD problems in Azerbaijan oil fields, this paper proposed a chemical method and optimized the type and the concentration of chemical inhibitors. And then the effect of selected chemical reagent on inhibiting the ARPD amount and thus en-hancing oil recovery was detected by reservoir simulation during both waterflooding and CO2 flooding production. Three new chemical compounds (namely, Chemical-A, Chemical-B and Chemical-C) were examined in laboratory conditions and their impact on rheological properties of high-paraffin oilfield samples of Azerbaijan (X, Y and Z) were investigated. Experimental results show that Chemical-C with concentration of 600 g/t has the best efficiency for alleviating the problems. After adding Chemical-C to the crude oil, the freezing point of oil is decreased from 12 °C to (-4) °C, ARPD amount is declined from 0.185 to 0.016 g and oil effective viscosity is reduced from 16.2 mPa·s to 3.1 mPa·s. It is determined that for water and CO2 flooding, higher injection pressure resulted in reduced asphaltene precipitation. Adding selected ARPD inhibitor, the oil recovery for waterflooding can increase from 52% to 62%, while it can rise from 55% to 68% for CO2 flooding.

Objectives. The aim of the study is to identify relevant research topics based on pooled bibliometric data of International Journal of Hydrogen Energy publications from 2022-2024, collected from The Lens and ScienceDirect platforms. Data source. Bibliometric records of International Journal of Hydrogen Energy articles published in 2022-2024 from The Lens and ScienceDirect platforms were used. Programs and utilities used. VOSviewer, Scimago Graphica, Inkscape, FP-growth utility. Results. The study showed the feasibility of merging bibliometric records from the open platforms ScienceDirect and The Lens, which complement each other. The 'Fields of Study' data of The Lens can be rationally interpreted as system keywords similar to Scopus Index Keywords. The possibility of using 'Fields of Study' data in a method similar to bibliographic coupling is shown. The practicality of using an Alluvial diagram to show the co-occurrence of the four terms was demonstrated. The study also emphasizes the advisability of joint use of VOSviewer and Scimago Graphica programs for complex visualization of bibliometric analysis results. The study identified two dominant publication topics in International Journal of Hydrogen Energy for 2022-2024, which can be described in terms of: 'Catalysis, Hydrogen, Physical_chemistry, Chemical_engineering, Nanotechnology, Electrochemistry, Organic_chemistry, Materials_science' and 'Electrical_engineering, Hydrogen_production, Renewable_energy, Environmental_science, Hydrogen_economy, Hydrogen, Engineering'.

Objectives. The aim of this study was to demonstrate the ability to visualize the results of the Scilit platform's bibliometric data analysis on the topic "AI & Machine Learning" to identify publications reflecting specific issues of the topic. Data source. Bibliometric records exported from the Scilit platform on the topic "AI & Machine Learning" for the years 2021–2023 were used. For each year, 6,000 records were downloaded in CSV and RIS format. Programs and utilities used. VOSviewer, Scimago Graphica, Inkscape, FP-growth utility, GSDMM algorithm. Used services: Elicit, QuillBot, Litmaps. Results. It has been shown that bibliometric data from the open access abstract database Scilit can serve as a quality alternative to subscription-only databases. Data exported from the Scilit platform require preprocessing to make them available in a format that can be processed by programs such as VOSviewer and Scimago Graphica. The use of GSDMM and FP-growth algorithms is effective for structuring bibliometric data for further visualization. The Scimago Graphica software provides wide possibilities for building compound diagrams, in particular, for representing the network of keywords in such important coordinates for bibliometric analysis as average year of publication and average normalized citation, as well as for building an alluvial diagram of co-occurrence of more than two keywords. The possibility of using such services as elicit.com, quillbot.com and app.litmaps.com to accelerate the selection of publications on the topic under study is shown.

Background. Keyword co-occurrence analysis is a crucial tool for comprehending research trends, identifying relevant studies, and gaining insight into the connections between various concepts and topics. Objective. This study focuses on analyzing the co-occurrence of keywords using FP-growth algorithm and direct search methods. Materials and methods. The methodology involved extracting bibliometric data of Energies journal for 2023-2024 from MDPI publisher platform, keyword lemmatization and keyword co-occurrence estimation. Clustering and visualization were performed using Multidendrograms and Scimago Graphica software. Results. The results showed that the FP-growth algorithm can achieve a close match with the direct search results, which facilitates data preparation for clustering. In addition, finding the co-occurrence of three or more keywords significantly reduced the number of possible combinations, which allowed the identification of specific research topics. Conclusions. This study highlights the usefulness of the FP-growth algorithm in keyword analysis and provides insights into ways to refine search queries to abstract databases for the purpose of designing and writing literature and systematic reviews.

Relevance of the subject. Keyword selection is critical to finding relevant literature and requires justification for querying abstract databases and other sources to ensure accuracy and completeness. The topic of Energy Systems is of great importance due to the introduction of renewable energy sources, modern control methods, and complex energy systems during the energy transition. The aim of this study. The goal of this paper was to identify keywords that would be useful to subject matter experts when collecting literature on a particular topic, based on entries in the IEEE Terms field. Data. Bibliometric data were exported from the IEEE Xplore platform in the following order: for 2019-2023, 2000 records sorted by relevance, for 2024, 1680 records current as of April 11, 2024. Analytical methods applied and software used. VOSviewer, Scimago Graphica implementing the Clauset-Newman-Moore algorithm and agglomerative hierarchical clustering method implemented in Multidendrograms. Results. The main issues of the Energy Systems topic are presented in tabular and graphical formats. The fpgrowth utility offers flexible data preparation options, which makes it worthwhile to conduct a separate study to analyze the score of co-occurrence terms given by its algorithm.

Purpose of publication: - Preparation of bibliometric data exported from the Scilit platform on energy efficiency and conservation for further analysis to identify relevant research topics. - To identify potential issues in the processing of data exported from the Scilit platform. - Providing colleagues with the opportunity to use the prepared data and examples of their analysis for independent research on topical issues of energy efficiency and energy conservation using materials provided by the Scilit platform. Research Materials: Files in CSV and RIS formats exported from Scilit for the query "energy conservation OR efficiency" in Common Fields [Title, Abstract, Keyword], using filters: Content Type → Journal Article; Year→2021-2023; Subject → Industrial Engineering (29.8K), Energy and Fuel Technology (9.8K), Manufacturing Engineering (9.2K). A total of 30K records sorted by their relevance (10K for each year) were exported. Data are current as of 14-03-2024. Methods: Preprocessing of title, annotation, and keyword field texts using lemmatization dictionaries collected on GitHub, removal of keywords taken from GATE and spaCy, and "manual" editing. Using VOSviewer to analyze publication topics by clustering keywords based on their co-occurrence. Using Scimago Graphica to build bubble diagrams.Application of the GSDMM algorithm for clustering bibliometric records by title and annotation texts. Creation of a dictionary for this algorithm using the keyword field.Use of the Carrot2 demo version and the NMF algorithm for a more detailed analysis of the topics of the record clusters obtained from GSDMM. Results: are presented in the form of initial and interim tables and graphs obtained in the course of this study. The full tables are provided as references to the attached materials. Supplementary material for this preprint on figshare: Chigarev, Boris (2024). Supplementary material for preprint "Analyzing the Possibilities of Using the Scilit Platform to Identify Current Energy Efficiency and Conservation Issues". figshare. Dataset. https://doi.org/10.6084/m9.figshare.25574058.v1

This article focuses on the issue of motor oils used in the engines of off-road mobile machinery (NRMM), more specifically tractors. The primary goal of the paper is to determine the appropriate replacement interval for these oils. The physical properties of the examined samples were first determined by conventional instruments. Furthermore, the concentration of abrasive metals, contaminants, and additive elements were measured using an optical emission spectrometer. Lastly, the content of water, fuel, glycol, and the products of oxidation, nitration, and sulphation were determined by using infrared spectrometry. The measured values were compared to the limit values. Based on the processing and evaluation of these analyses, the overall condition of the oils was assessed and subsequently the optimal exchange interval of the examined oils was determined. In addition, a risk analysis of the outage was performed. Due to the high yields of crops, farmers can lose a significant amount of product when a tractor is not functioning during the harvest period. This loss for calculated in the paper.

With the offshore oil-gas fields entering decline phase, high-efficiency separation of oil-gas-water mixtures becomes a significant challenge. As essential equipment for separation, the three-phase separators play a key role in Offshore Oil-Gas production. However, level control is critical in the operation of three-phase gravity separators on offshore facilities, as it directly affects the efficacy and safety of the separation process. This paper introduces an advanced deep deterministic policy gradient with adaptive learning rate weights (ALRW-DDPG) control algorithm, which improves the convergence and stability of the conventional DDPG algorithm. An adaptive learning rate weight function is meticulously designed, and an ALRW-DDPG algorithm network is constructed for simulating three-phase separator liquid level control. The effectiveness of the ALRW-DDPG algorithm is subsequently validated through simulation experiments. The results show that the ALRW-DDPG algorithm achieves a 15.38% improvement in convergence rate compared to the traditional DDPG algorithm, and the control error is significantly smaller than that of PID and DDPG algorithms.

The application of thermoelectric generators (TEG) on the nozzle of an aviation jet engine was studied by finite element TEG-simulations. Against the background of system-level requirements of the reference aircraft this work reports the resulting requirements on the TEG design with respect to applied thermoelectric (TE) element lengths and fill factors (F) within the TE modules in order to maintain a positive effect on the specific fuel consumption. Assuming a virtual optimized TE material and varying the convective heat transfer coefficients at the nozzle surfaces this work reports the achievable power output. System-level requirement on the gravimetric power density (> 100 Wkg-1) can only be met for F ≤ 21%. Extrapolating TEG coverage to the full nozzle surface, the power output reaches 1.65 kW per engine. Assessment of further potential is demonstrated by a parametric study on the fill factor, convective heat transfer coefficients, and materials performance. This study confirms a feasible design range for TEG installation on the aircraft nozzle with a positive impact on the fuel consumption. This application translates into a reduction of operational costs, allowing for an economically efficient installation of TEG in consideration of the cost-specific power output of modern thermoelectric materials.

The consideration toward Waste Cooking Oils (WCOs) is changing from hazardous waste to valuable raw material for industrial application. During the last five years some innovative processes based on the employment of recycled WCO have appeared in the literature. In the present review article, the most recent applications of recycled Waste Cooking Oil are reported and discussed. These include the production of bio-plasticizers, the application of chemicals derived from WCOs as energy vectors, and the use of WCOs as solvent for pollutant agents.

Biofuels have become an integral part of everyday life in modern society. Bioethanol and fatty acid methyl esters are a common part of both the production of gasoline and diesel fuels. Also, pressure on replacing fossil fuels with bio-components is constantly growing. Waste vegetable fats can be replacing biodiesel. HVO seems to be a better alternative. This fuel has a higher oxidation stability for storage purposes, a lower temperature of loss of filterability for the winter time, a lower boiling point for cold starts and other. Viscosity, density, cold filter plugging point of fuel blend, and flash point were measured to confirm that a fuel from HVO is so close to a fuel standard that it is possible to use it in engines without modification. The objective of this article is to show the properties of different fuels with and without HVO admixtures and to prove the suitability of using HVO compared to FAME. HVO can also be prepared from waste materials and no major modifications of existing refinery facilities are required. No technology in either investment or engine adaptation of fuel oils is needed in fuel processing.

The alternating stress caused by periodic high-pressure injection and extraction in gas storage can potentially induce fault slippage, compromising the sealing integrity of faults within these facil-ities. Understanding the mechanical behavior of faults under alternating stress is crucial for en-suring the long-term stability and safety of gas storage operations. To explore the impact of fault dip angle and fault gouge strength on fault slip characteristics, fault samples were prepared with uniaxial compressive strengths of 20.1, 30.2, 42.4, and 51.4 MPa at two distinct dip angles. Triaxial compression experiments were conducted under alternating stress conditions corresponding to operational pressures at a specific gas storage in China. Results indicate that faults with dip angles of 30° and 45° tend to fail at their weakest points. Increasing strength of fault gouge shifts failure mechanisms from interfacial failure between gouge and surrounding rock towards internal gouge failure, often accompanied by shear failure across sections, resulting in characteristic "X"-shaped conjugate shear failures. The decrease in the ratio of bedrock strength to fault gouge strength elucidates the observed phenomena of initial reduction followed by increased fault deformation. Transition points for faults with 30° and 45° dips occur around the strength ratios of 1.7/1 and 1.2/1, respectively. Fault damage exhibits a negative correlation with fault gouge strength and a positive correlation with fault dip angle. Samples with higher strength fault gouge at a 30° dip angle generally incur less damage compared to those with lower strength fault gouge at a 45° dip angle. Moreover, higher maximum static friction coefficients denote greater fault resistance to slipping, with 30° faults consistently demonstrating superior resistance compared to 45° faults. Additionally, higher strength fault gouge consistently enhances slip resistance under identical dip angles.

This paper presents the results of investigations into the pyrolysis of waste polypropylene in a laboratory fixed-bed batch reactor. The experiments were designed and verified in such a way as to allow the application of the Response Surface Methodology (RSM) in the development of an empirical mathematical model that quantifies the impacts mentioned above. The influence of the mass of the raw material (50, 100 and 150 g), together with the reactor temperature (450, 475 and 500 °C) and the reaction time (45, 50 and 75 min) was examined. It has been shown that the mass of the raw material, i.e. the filling volume of the reactor, has a significant influence on the pyrolysis oil yield. This influence exceeds the influence of reactor temperature and reaction time. This was explained by observing the temperature change inside the reactor at three different spots at the bottom, middle and top of the reactor. Recorded temperature diagrams show that with greater masses of feedstock, local overheating occurs in the middle part of the reactor, which leads to overcracking of vapor products, and from there to an increased formation of non-condensable gases, i.e. reduced yield of pyrolytic oil.

Conventional traceability systems in Cambodian agriculture, such as Rubber Supply Chain Management (RSCM), often struggle to provide timely data and fair market prices, leading to mistrust among stakeholders, exploitation by intermediaries, and hindering progress towards ethical sourcing and sustainable practices. This research aims to showcase the potential of integrating blockchain technology, the Internet of Things (IoT), the InterPlanetary File System (IPFS), and Differential Privacy (DP) methods to empower Cambodian rubber farmers. By enhancing transparency, facilitating fair pricing, and promoting sustainable methods in the rubber industry, this integrated approach leverages Hyperledger Fabric (HLF) to create a decentralized and secure system for tracking rubber from its source to the end consumer. Integration with IPFS ensures secure and easily accessible data storage, further enhancing the system’s reliability. Additionally, the implementation of differential privacy techniques safeguards confidential data during information sharing among farmers and supply chain stakeholders, minimizing potential privacy concerns. This comprehensive system encourages consumers to make ethical and sustainable alternative options by providing accessible information on harvesting methods, processing procedures, labor conditions, and environmental impacts. The potential benefits extend beyond Cambodia, serving as a model for other developing countries aiming to modernize and enhance the agricultural distribution networks. Our results show that transaction send rates (TPS) and throughput in systems with and without differential privacy grow with increased transaction volumes. However, the system without differential privacy achieves greater scalability and efficiency above a certain threshold. However, it offers a slightly reduced latency, reflecting a trade-off between privacy and performance efficiency in blockchain-based agricultural traceability systems.

Biodiversity loss and nature degradation are pressing issues with huge impacts on our society and economy. Businesses, investors, and regulators focus on corporate efforts to support biodiversity and nature positive actions. This review provides a comprehensive overview about the importance of biodiversity in businesses, the materiality of biodiversity and the role of mandatory and non-mandatory regulations on corporate environmental reporting and sustainability disclosure frameworks. The review also discusses descriptive information on the evolution of sustainability frameworks with a comparison of most prominent sustainability frameworks with a key focus on the materiality approach and biodiversity-related disclosure recommendations. Further, we provide suggestions for more holistic approaches to improve the future sustainability frameworks focusing on the biodiversity impact while showing the necessity of more focus on the decision-making paradigm. Further research on measuring biodiversity impact and innovative trends in sustainability reporting are required to better reflect nature-positive outcomes in corporate sector businesses.

As one of the important wastes, waste PET pollutes human living and natural environment seriously. PET is an important solid waste that needs to be recycled at present. The complete degradation of PET was realized at low temperature. The lipophilic hydrophobic membrane was formed on the surface of stainless steel mesh (SSM) by a simple dip coating method, and the oil-water separation material was successfully prepared. Due to the load of degradation products, the surface roughness of SSM increased from 19.09 μm increased to 62.33 μm. The surface changed from hydrophilic to hydrophobic, and the water contact angle increased to 123o. The oil-water separation flux of modified SSM is 9825 L/(m2·h) and the separation efficiency is 98.99%. The modified SSM has good reuse performance. This hydrophobic modification method can also be used to modify other porous substrates, such as activated carbon, filter paper, foam, and other materials. In this study, the porous substrate modified by the degradation product of waste PET was used to prepare oil-water separation materials, which not only solved the problem of white pollution, but also reduced the dependence on non renewable resources in the conventional preparation methods of oil-water separation materials. The research provided new raw materials and methods for the industrial production of oil-water separation materials, and had important application prospects.

One way to increase overall natural gas engine efficiency is to transform exhaust waste heat into useful energy by means of a bottoming cycle. Organic Rankine cycle (ORC) is a promising technology to convert medium and low grade waste heat into mechanical power and electricity. This paper presents an energy and exergy analysis of three ORC-Waste heat recovery configurations by using an intermediate thermal oil circuit: Simple ORC (SORC), ORC with Recuperator (RORC) and ORC with Double Pressure (DORC), and Cyclohexane, Toluene and Acetone have been proposed as working fluids. An energy and exergy thermodynamic model is proposed to evaluate each configuration performance, while available exhaust thermal energy variation under different engine loads was determined through an experimentally validated mathematical model. Additionally, the effect of evaportating pressure on net power output , absolute thermal efficiency increase, absolute specific fuel consumption decrease, overall energy conversion efficiency, and component exergy destruction is also investigated. Results evidence an improvement in operational performance for heat recovery through RORC with Toluene at an evaporation pressure of 3.4 MPa, achieving 146.25 kW of net power output, 11.58% of overall conversion efficiency, 28.4% of ORC thermal efficiency, and an specific fuel consumption reduction of 7.67% at a 1482 rpm engine speed, a 120.2 L/min natural gas Flow, 1.784 lambda, and 1758.77 kW mechanical engine power.

In this paper, the performance and emission characteristics of the engine were investigated with varying ratios of tung oil-based biodiesel blends (B10, B20, and B50) and 0# diesel under different operating conditions. The experimental results indicated that both the power and torque of B10 increased compared with 0# diesel, which increased by 1.9% and 6.6%. But the power and torque of B20 and B50 decreased slightly. The fuel consumption rate increased slightly with an increasing percentage of biodiesel added. In general, the overall emissions of tung oil-based biodiesel blends were lower compared to 0# diesel. Compared to 0# diesel, the CO-specific emissions of B10 decreased by 42.86% at medium and large load, and NOX-specific emissions of tung oil-based biodiesel blends were reduced at all load conditions, except for B50. In addition, HC-specific emissions were all reduced, especially for B20 decreased by 27.54% at 50% load. With the increase of the biodiesel blend ratio, the smoke decreased significantly. Among the blends tested, B50 showed the greatest reduction of 38.05% at 2000 rpm. Overall, it can be asserted that using biodiesel presents a favorable alternative fuel option that can lead to a more environmentally friendly exhaust output.

In order to achieve the dual carbon goal and simplify the decarbonization process, a CO2 recovery process of the fire-flooding exhaust was designed. The process adopted the two-stage membrane separation method to recover CO2 and obtain high purity CO2 rich flow, and then through the mixed refrigerant liquefaction and rectification column, food grade liquid CO2 was obtained. HYSYS process simulation shows that for the fire-flooding exhaust with a flow rate of 1000 kg/h and a given composition, the process can achieve a CO2 recovery of 69.02%, total product sales S=2086.8 yuan/h, and specific power consumption of 2.818 kW∙h/kg. On this basis, a hybrid simulation platform of HYSYS & Matlab was established. Taking the specific power consumption of the product as the objective function, sequential quadratic programming (SQP) algorithm was adopted to optimize the process, and the optimized specific power consumption was reduced by 18.8%. Finally, by adjusting N2/CO2 components, the adaptability of the optimization condition was analyzed.

In this work, the properties of a composition based on synthetic rubber ethylene-propylene ter-polymer and polymers with functional groups of the mixture are studied. Low efficiency of some compositions based on ethylene and propylene copolymer limits their use in the production of tires and rubber products. Therefore, we conducted a study to improve the disadvantages of SREPT-60 using butyl rubber + choro polyisoprene + butadiene-nitrile + butadiene styrene rubber and adding a plasticizer to the composition = α, methacrylate-(bis-diethylene glycol phthalate) -(btegf-9) The data obtained showed that a number of its indicators of rubber based on them were improved. Tear resistance, resistance to repeated stretching increased, adhesion of the composition to metal, chemical resistance increased, the degree of swelling in benzene and gasoline-benzene mixture decreased. Compositions based on the mixture SREPT-60 using butyl rubber + choro polyisoprene + butadiene-nitrile + butadiene styrene rubber and adding a plasticizer to the composition = α, methacrylate-(bis-diethylene glycol phthalate) -(btegf-9) +Dioctyl phthalate: (70:20:10) have high resistance to swelling in an aggressive environment (Benzene, gasoline, alcohol, acid, oil, etc.) mixture.

A shrimp oil rich in omega-3 lipids and carotenoids is obtained in remarkably high 5 wt% yield extending to pink shrimp processing waste (head and carapace) the circular economy approach to extract fish oil from fish processing by-products using d-limonene. Biobased limonene, a powerful antimicrobial and antioxidant agent, is an excellent solvent for both lipids and astaxanthin-based carotenoids preventing oxidative degradation during the extraction cycle including solvent and oil separation at 85°C. A new low cost route is established to extract valued marine oil from biowaste annually made available in over 2.2 million tonnes.

As waterflooding multi-layer reservoirs get into the high-water-cut stage, inter-layer conflicts become increasingly serious, leading to a worsening development effect over time. Production layers regroup is an effective approach for resolving inter-layer conflicts and improving waterflooding efficiency. At the current stage, there are limitations for most of the methods of production layers regroup. This article proposes a smart method for optimizing the layer regroup plan based on genetic algorithm. Comprehensively considering various factors that affect the regroup of layers, based on the combination principle of "smaller intra-group variance and larger inter-group variance of each influencing factor are expected ", genetic algorithm is used to calculate the fitness value of the initial combination schemes, the advantageous schemes with higher fitness values are selected as the basis of the next generation. Then crossover and mutation operations are performed to those advantageous schemes to generate new schemes. Through continuous selection and evolution, until the global optimal solution with the highest fitness value is found, the optimal combination scheme is determined. Comparative analysis with numerical simulation results demonstrates the reliability of this intelligent method, with an increased oil recovery of 4.34% for the sample reservoir. Unlike selecting a preferable plan from a limited number of predefined combination schemes, this method is an automatic optimization to solve the optimal solution of the problem. It improves both efficiency and accuracy as compared to conventional reservoir engineering methods, numerical simulation methods and most of the mathematical methods, thus could provide effective guidance for EOR strategies of waterflooding reservoirs in high-water-cut stage.

In order to establish the formation patterns of the Co–Mg oxide system, samples with different Co:Mg ratios and heat treatment temperatures were synthesized and studied. Study of the sam-ples confirmed the phase transition of MgxCo2–xO4 spinels into corresponding solid solutions at 800–900 °C. The similarity of formation patterns for different compositions is shown. The rock-salt oxide in low-temperature samples is an anion-modified paracrystalline phase that forms a “true” solid solution only upon spinel decomposition. TPR profiles of decomposed Co3O4 spinel show surface Co3O4 peaks and a wide peak corresponding to well-crystallized CoO, while par-tial Co3O4 TPR up to 380 °C results in dispersed and amorphous CoO. High-temperature non-stoichiometric samples are poorly reduced, indicating their low oxygen reactivity. Spinel reoxidation after heat treatment to 1100 °C by calcination at 750 °C showed complete regenera-tion for MgCo2O4–Co3O4 samples and its absence in case of an excess of MgO relative to stoi-chiometry. Based on the data obtained, it can be concluded that the processes governing the formation of Co–Mg oxide systems are determined by both Co:Mg ratio and the heat treatment conditions, potentially providing the possibility of fine tuning for specific catalytic processes.

The article presents the influence of ecological agents, i.e. the effective microorganisms and silver compounds addition to lubricating oil on operating parameters of an internal combustion engine. The basic diagnostic parameters of a piston engine determining its technical condition were described. In the further part, the research stand and materials were presented. In the main part of this article for pure oil compared to oil with the effective microorganisms and silver compounds addition were shown. It was found that the addition of effective microorganisms and silver compounds to the oil reduces the emission of toxic components into the atmosphere along with the exhaust gases, while the remaining engine operating parameters for each load value show that these additives do not cause deterioration of the technical condition of the tested engine. Of all the agents used, the best results are obtained with the addition of ceramic tubes, because it is an additive that does not affect the properties of the oil in its composition. The advantage of ceramic tubes is the slow release of effective microorganisms, which has an effect on the parameters of the oil and thus on the operation of the engine. In further research, it will be checked how these additives affect the anti-seize and anti-wear properties of the lubricating oil used, which should give a broader view of the impact of these additives on the technical condition of the operated piston engine.

Plastics, once regarded as a revolutionary material shaping modern society, now poses an unprecedented threat to our environment. Household solid waste sorting stations produce several fractions, one of which contains a high concentration of Low-Density Polyethylene (LDPE) film waste (packaging, sunscreen film, etc.). This fraction is difficult to recycle because it contains quite a lot of impurities. Usually, it is sent to the cement factories that burn it together with other fuels. However, with some processing techniques such catalytic pyrolysis this fraction could be valorized. In this paper the experiments which were carried out at a laboratory scale installation, in batches with a processing capacity of 1-3 kg of waste. The pyrolysis reactor is connected to a distillation column giving the possibility to separate the fractions. The gaseous and liquid fractions were characterized by GC-FID-TCD (gases) and GC-MS (liquids) analysis. Natural catalysts such as bentonite or clinoptilolite were studied and used in the melting of plastic mass to simplify the process as much as possible. To test the activity of the catalysts, the pyrolysis of LDPE granules was initially studied. It was found that natural zeolites are much more active than bentonite and that a minimum concentration of 5-10% is needed to have a positive effect on the composition of the fractions (increasing the weight of the light fractions C1-C6, C6-C10 and C11-C13) in relation to the heavy fractions C13-C20 and C20+. Catalytic pyrolysis gives a completely different distribution of light hydrocarbons. The best catalyst selected from LDPE lab experiments, was then tested upon the pyrolysis of plastic film waste obtained by a waste treatment plant. The research objective reported in this paper was to obtain a fraction of combustible gases in the largest possible proportion, which can be much easier exploited by burning in an engine that drives an electric generator.

Spray penetration into citrus canopies is critical for adequate coverage and deposition to ensure effective pest control. However, mismatch of air assistance to target canopy characteristics can lead to unintended spray loss through over penetration. To evaluate the effect of air assistance on on-target deposition, two sprayers (surrogates for airflow rates) were used to apply a fluorescent tracer dye solution @ target concentration of 300 ppm to 16 medium foliage density tree blocks in a commercial mandarin orchard. The complete factorial experiment in three replications comprised two ground speeds (1.6 and 4.8 km/h), two disc-core nozzles (TeeJet® D3-25 and D6-45), and either one or two nozzle rows to obtain a wide range of application rates (496 to 9,719 L/ha). Dye deposition significantly decreased with canopy depth (p=<0.001) by nearly 7 times across the 3.4-m-wide canopies but was not significant over 1.2 to 2.2 m sampling height (p=0.867). Deposition obtained with the low airflow rate sprayer was significantly greater (p=<0.001) than that obtained with the high airflow rate sprayer over the dose range likely due to too much air pushing out spray droplets. This study underscores the importance of matching the air assistance of orchard sprayers to the target canopy.

Analyses of the three predominant types of sedimentation – clastic, carbonate and black shale – revealed their discontinuity/continuity in different facies environments of the Middle and Late Devonian of the central part of the Volga-Urals petroleum province, namely (1) in depressions, both condensed and non-condensed, (2) on the slopes of depressions and (3) in shallow water environments represented by tectonic arches or localised biohermal uplifts. The regional zonation of conodonts, correlated with the global chronostratigraphic scheme, substantiates the stratigraphic completeness of the general Devonian sequence in this area. In particular, the sedimentation of organic-rich black shales, traditionally considered as source rocks, lasted more than 29 million years, starting from the Late Eifel and ending at the Devonian-Carboniferous boundary. There was only one hiatus in the deposition of both black shales and carbonate sediments, lasting about 2.5 million years at the end of the Frasnian. That interval is dominated by clastic sediments, which are considered to be the most productive reservoirs of the Volga-Ural province. In the time interval from the beginning of the Eifel to the end of the Frasnian (about 17 Ma), (a) clastic sediments show the highest accumulation rates; (b) the most complete sequences occur in depressions; and (c) arches and uplifts show the most significant gaps in the geological record. During Famennian, (a) clastic sedimentation has completely ceased; (b) differences between the slopes of troughs and shallow-water environments have diminished, resulting in stable accumulation of carbonate sediments in both settings; (c) the decrease in sequence thickness (up to 50 m) in depressions suggests reduced accumulation rates of deep-water organic-rich black shales. The results help to understand the complex spatial relationship between different coexisting sedimentation types and focus attention to the incompleteness of the geological record in different environments.

Phased injection of natural gas into internal combustion marine engines is a promising solution for optimizing performance and reducing harmful emissions, particularly unburned methane, a potent greenhouse gas. This innovative practice distinguishes itself from continuous injection because it allows for more precise control of the combustion process with only a slight increase in system complexity. By synchronizing the injection of natural gas with the intake and exhaust valve opening and closing times while also considering the gas path in the manifolds, methane release into the atmosphere is significantly reduced, making a substantial contribution to efforts to address climate change. Moreover, phased injection improves the efficiency of marine engines, resulting in reduced overall fuel consumption, lower fuel costs, and increased ship autonomy. This technology has been tested on a single-cylinder, large-bore, four-stroke research engine designed for marine applications, operating in dual-fuel mode with diesel and natural gas. Performance was compared with that of the conventional continuous feeding method. Evaluation of the effect on equivalent CO2 emissions indicates a potential reduction of up to approximately 20%. This reduction effectively brings greenhouse gas emissions below those of the diesel baseline case, especially when injection control is combined with supercharging control to optimize the air-fuel ratio.

High-precision conical threads are widely used in responsible joints in the drilling of oil and gas wells. Difficult underground drilling conditions due to the occurrence of significant mechanical loads and an aggressive environment in wells require the use of workable materials that are often difficult to machine. The huge need for such connections dictates the use of high-performance cutting tools, which means that high demands are placed on their effective geometric performance. The study describes the theoretical dependence of the profile precision of the tapered drill-string tool-joint threads of all standard sizes on the complex of a cutting tool geometric parameters and cutting tool setting accuracy. The experiments include an assessment of the geometric accuracy of the profile of the obtained NC23 thread connector, depending on the values of the installation angles and the declared tangential displacement of the standard threaded carbide insert.

This study investigates the influence of adding hydrogen as an additive to gasoline in a four-stroke engine, utilizing a comprehensive thermodynamic comparative analysis conducted with self-developed engine model. The research aims to assess the performance, emissions, and efficiency of the engine when using gasoline-hydrogen blends, and to provide insights into the potential benefits of this approach. First the engine performance and emissions under different hydrogen blending levels were examined. A range of different air-to-fuel ratios (rich to lean) and varying percentages of hydrogen were considered. This systematic variation allowed for a detailed evaluation of the influence of hydrogen content on combustion efficiency, power out-put, and emissions characteristics. The analysis results included key parameters such as indicated specific fuel consumption and mean effective pressure. Additionally, the study focused on range prediction of nitrogen oxides (NOx) emissions, which are a critical environmental concern asso-ciated with internal combustion engines. The analysis of pressure and temperature profiles throughout the engine cycle shed light on the combustion characteristics and efficiency im-provements associated with hydrogen addition. In terms of emissions, the study projected that all emissions were reduced except NOx, which is highly dependent on hydrogen percentage, and it might be reduced in some cases, but with higher temperatures and pressures associated with hydrogen addition in most cases there is actually NOx increase, especially at higher engine loads.

Soluble inorganic pyrophosphatase (sPPase), a pyrophosphate hydrolase, has been shown to play an important role in several physiological processes such as plant growth and development, metabolic activities, and response to abiotic stresses, but sPPase has been less studied in woody plants. In order to preliminarily verify whether the soluble inorganic pyrophosphatase in Eucommia ulmoides Oliver (E. ulmoides) has a role in resistance to drought stress, we amplified the EuSIP5 (E. ulmoides soluble inorganic pyrophosphatase 5) cDNA sequence from E. ulmoides by RT-PCR. In order to study the drought resistance of the Eucommia ulmoides soluble inorganic pyrophosphatase 5 (EuSIP5) gene, the cDNA sequence of the EuSIP5 gene was amplified from Eucommia ulmoides Oliver by RT-PCR. Bioinformatic analysis indicated that EuSIP5 might be an unstable amphipathic protein, mainly located in the cytoplasm. E. ulmoides, the highest expression of the EuSIP5 gene was found in male leaves and pericarp from April to October, and in leaves of E. ulmoides in July and September. During drought, the expression of EuSIP5 in seedling E. ulmoides leaves was significantly higher than that of the control. An overexpression vector harboring the EuSIP5 was constructed and introduced into the tobacco (Nicotiana tabacum cv. Xanthi). We found that during drought stress, the appearance of wilting was delayed by 4 days in transgenic tobacco plants (OE) compared with wild type plants (WT), and the expression of drought-related genes DET2, CYP85A1, P5CS, ERF1 and F-box was found to be increased in transgenic tobacco leaves, as well as the enzyme activities of the protective enzymes: peroxidase (POD), superoxide dismutase (SOD) and catalase (CAT) were significantly higher than those of the WT, and the malondialdehyde (MDA) content was lower than the WT. These results indicated that the introduction of EuSIP5 gene into tobacco increased the expression of drought-related genes, enhanced the anti-membrane oxidation ability of tobacco, and reduced the oxidative stress damage, thus improving the drought resistance of tobacco.

This study aims to examine the non-volatile Particle Number (PN) emissions of a retrofitted Heavy-Duty Spark-Ignition (HD-SI) engine powered by liquefied petroleum gas (LPG) under both steady-state and transient conditions. The engine was tested under seven steady-state operating points to investigate the PN behavior and Particle Size Distribution (PSD) upstream and down-stream of the Three-Way Catalyst (TWC). This analysis intends to assess the impact of including particles with diameters ranging from 10 nm to 23 nm in the total particle count, a consideration for future regulations. The study employed the World Harmonized Transient Cycle (WHTC) for transient conditions to encompass the same engine working region used in the steady-state analysis. A Dekati FPS-4000 diluted the exhaust sample to measure the PSD and PN for particle diameters between 5.6 nm and 560 nm using the TSI-Engine Exhaust Particle Sizer (EEPS) 3090. Findings indicate that PN levels tend to increase downstream of the TWC under steady-state conditions in operating points with low exhaust gas temperatures and flows (equal to or less than 500 °C and 120 kg/h). Furthermore, the inclusion of particles with diameters between 10 nm and 23 nm leads to an increase in PN emissions by 17.70% to 40.84% under steady conditions and by an average of 40.06% under transient conditions, compared to measurements that only consider particles larger than 23 nm. Notably, in transient conditions, most PN emissions occur during the final 600 seconds of the cycle, linked to the most intense phase of the WHTC.

Anchovies are amid the largest fish catch worldwide. The anchovy fillet industry generates a huge amount of biowaste (e.g. fish heads, bones, tails) that can be used for the extraction of several potentially valuable bioproducts including omega-3 lipids. Following the extraction of valued fish oil rich in omega-3, vitamin D₃ and zeaxanthin from anchovy fillet leftovers using biobased limonene in a fully circular process, the solid residue was used as starting substrate for the production of biogas by anaerobic digestion. The results first reported in this study demonstrate good potential energy recovery of the anchovy sludge of about 280 mL_CH4∙g_VS^-1. Due to unbalanced C/N ratio typical of marine biowaste, co-digestion with a carbon rich substrate is recommended.

This study investigates the potential of a hybrid nanofluid composed of MoS2 and ZnO nanoparticles dispersed in engine oil, aiming to enhance the properties of lubricant's chemical reaction with the Soret effect on stretching sheet under the influence of applied magnetic field. With the growing demand for efficient lubrication systems in various industrial applications, including automotive engines, the development of novel nanofluid-based lubricants presents a promising avenue for improving engine performance and longevity. However, the synergistic effects of hybrid nanoparticles in engine oil remain relatively unexplored. This research addresses this gap by examining the thermal conductivity, viscosity, and wear resistance of the hybrid nanofluid, shedding light on its potential as an advanced lubrication solution. By analyzing the dispersion stability and interaction mechanisms between nanoparticles and base oil, valuable insights are gained into the fundamental aspects governing the entertainment of hybrid nano lubricants. Overall, the objectives of studying hybrid nano lubricant MoS2+ZnO with engine oil aim to advance the development of more efficient and durable lubrication solutions for automotive engines, contributing to improved reliability, fuel efficiency, and environmental sustainability. Governing non-linear partial differential equations are simplified as ordinary differential equations by utilizing similarity variables. MATLAB Bvp4c technique is used to solve the obtained linear ODE equations. The outputs are presented through graphs and tables for various state variables. The comparative survey in all the graphs is presented for the nanofluid (MoS2/Engine oil) with the hybrid nanofluid (MoS2+ZnO/Engine oil). These graphs show the effect of various parameters M, Q, β, Pr, Ec, Sc, Sr, Kp, Kr and (hybrid nano lubricant parameter). The velocity profile diminished against the values of M, Kp, and β. Temperature profile rising with Ec and Q. reciprocally goes down to Pr. The concentration profile incremented with the value of Sr and decremented with the value of Sc, and Kr. With the increasing value of both f′ (η) and θ(η) increases. But in θ(η) hybrid nanofluid slows down with the higher value of .

In order to develop novel botanical insecticides, the joint action of Ligusticum chuanxiong oil (LCO) and lemongrass oil (LO) against Aphis citricola van der Goot was determined systematically indoors and outdoors. The chemical profiles of LCO and LO as determined by gas chromatography- mass spectrometry analysis revealed that main compounds from LCO were Z-Ligustilide (44.58%) and Senkyunolide A (26.92%), and that of LO were geranial (42.16%) and neral (32.58%), respectively. The mixture of LCO and LO showed significant synergy against A. citricola, with a common-toxicity coefficient (CTC) value of 221.46 at the optimal ratio of LCO to LO (4: 1, w/w). Based on the results of solvents and emulsifiers screening, L. Chuanxiong oil · Lemongrass oil 20% emulsifiable concentrate (20% LCO · LO EC) was developed, which was confirmed to meet the requirements of a commercial pesticide by quality test. Field trials indicated that the insecticidal activity of the diluted 20% LCO · LO EC (1000 fold dilution) was comparable to conventional pesticide (20% imidacloprid EC) on A. citricola 7 days after application. Thus, the mixture of LCO and LO has the potential to be further developed as a botanical pesticide.

The study aimed to compare the cardiovascular benefits of Omega-3 Polyunsaturated Fatty Acids from fish oil versus krill oil in different forms and dosages. Following PRISMA 2015, data analysis with R software, and databases were searched from 1993 to 2023, (ID PROSPERO: CRD42024502338). Sixty high-quality studies were analyzed, covering various forms of fish oil and krill oil at different dosages (fish oil (ethyl ester-EE, triglyceride-TG, re-esterified triglycerides-rTG, capsules, emulsion-EM); krill oil (phospholipid/free fatty acid-PL/FFA, high concentration phospholipid-HPL, low concentration phospholipid-LPL)). Meta-analysis revealed that krill oil with phospholipid/free fatty acid at doses 2000-2900 mg effectively lowered triglycerides, while fish oil in ethyl ester form at doses above 3000 mg significantly reduced total cholesterol. Fish oil in triglyceride form at doses 2000-2900 mg and other variations positively impacted HDL-C levels. Fish oil in EE form above 3000 mg and triglyceride form below 2000 mg notably reduced LDL-C. However, there was limited effectiveness observed for other interventions. Analysis for LDL-C exhibited publication bias, while other parameters demonstrated reliability (Egger's test). In conclusion, krill oil - PL/FFA, Fish oil - EE above 3000 mg, Fish oil - TG 2000-3000 mg, and fish oil - rTAG 300-1900 mg effectively in reducing heart risk patients.

The ubiquitous presence of microplastics (MPs) in the environment poses a threat to ecosystems and increases concerns about their exposure to the human body. However, despite being consumed for health improvement, limited research has been conducted on MPs in functional foods. This study aimed to investigate the occurrence of MPs and the relation of the source of raw material or the manufacture in various omega-3 oil in the Korean market. MPs in omega-3 capsule and raw oil, sourced from both plant-based (PB) and animal-based (AB) sources, were investigated. We developed the method by direct filtration with acetone washing and analyzed MPs greater than 5 μm using microscope-Raman spectroscopy. The average number of MPs was found to be 1.2 ± 1.7 MPs/g for PB raw oil, 2.2 ± 1.7 MPs/g for AB raw oil, 3.5 ± 3.9 MPs/g for PB capsule oil, and 10.6 ± 8.9 MPs/g for AB capsule oil. Polypropylene and polyethylene terephthalate were major specious (83-95 %) found in omega-3 oil. The ratio of size range remained consistent across all groups, with a trend of higher detection rates as the size diminished. The results reveal that the main reason of MPs contamination is not the source of raw material but the manufacturing and packaging process for omega-3 oil.

Electronic waste generation has been following a continuously rising trend. With electronics containing a myriad of materials some of which are hazardous, toxic, extremely rare or precious combined with more stringent legislative laws which encourage the reuse and optimised recycling of the materials included in e-waste, the need for a holistic approach is inevitable. Such an approach should not only identify the materials found in the various types of e-waste and their respective quantities but also needs to highlight the possible handling techniques and their respective impacts and associated hazards whether to the environment or human health. Performing such a task manually would be exasperating and costly while requiring extensive resources which might not be met with a justifiable economic gain; thus, the use of the advancement in computational sustainability to draw a complete picture and aid in an informed decision-making process is crucial. The e-waste ontology developed in this paper is one way of addressing the problem since it covers the treatment domain, the hazard and the materials contained within the different types of e-waste. The ontology developed can be used directly from the protégé software or by embedding it into a developed Decision Support System.

Graphene was synthesized through a two-step pyrolysis method using waste candlenut (Aleurites moluccanus) shells as the precursor. Cerium (Ce)/graphene composites were prepared via an impregnation technique. The resulting graphene and Ce/graphene were characterized using various analytical methods, including Scanning Electron Microscopy with Energy-Dispersive Spectroscopy (SEM-EDS), X-ray Diffraction (XRD), X-ray Photoelectron Spectroscopy (XPS), Transmission Electron Microscopy (TEM), Thermo Gravimetric Analysis (TGA), Fourier Transform Infrared (FTIR) spectroscopy, Cyclic Voltammetry (CV), and Linear Sweep Voltammetry (LSV). The bio-carbon produced predominantly exhibited a graphene structure with flat carbon morphology and an interlayer distance of 0.33 nm. This structural information is supported by XRD data, which shows a broad and weak peak at 2θ = 26° corresponding to the C (002) plane, indicative of graphene presence. FTIR, XPS, and Raman spectroscopy further confirmed the presence of graphene through the detection of Csp2 aromatic bonds and the characteristic D, G, and 2D peaks. Notably, the performance of cerium can be enhanced by the incorporation of graphene, attributed to the large surface area and chemical interactions between Ce and graphene. Consequently, candlenut-derived graphene shows potential as a supportive material for modifying the properties of cerium, thereby opening avenues for various advanced applications, such as sustainable and high-performance energy storage systems.

The formation of hydrogen sulfide (H₂S) in petroleum reservoirs by anaerobic microbial activity is called biogenic souring of reservoirs and is a risk in the oil and gas industry as the compound is extremely toxic, flammable and corrosive. In this paper, we present a workflow and the tools to assess biogenic souring from a pragmatic engineering perspective. The retention of H₂S in the reservoir due to the reactions with iron-bearing rock minerals (e.g. siderite) is shown in a theoretical approach here and supported with literature data. Cases are given for two fields under secondary (waterflooding) and tertiary flooding with microbial enhanced oil recovery (MEOR). The use of the Monte Carlo method as a numerical modelling tool to incorporate uncertainties in the measured physical/chemical/ biochemical data is demonstrated as well. A list of studies conducted with different chemicals alone or in combination with various biocides to mitigate biogenic souring provides an overview of potential inhibitors as well as possible applications. Furthermore, the results of static and dynamic inhibition tests using molybdate are presented in more detail due to its promising mitigation ability. Finally, a three-step workflow for the risk assessment of biogenic souring and its possible mitigation is presented and discussed.

The quality of waste activated sludge produced in urban wastewater treatment systems varies according to the efficiency of the operation of treatment units along the content of microflora and organic carbon. However, these represent a biogas-energy alternative through anaerobic co-digestion, contributing to reducing the environmental impacts caused by their inadequate disposal. Biogas production by the Two-stage production method in batch digesters was evaluated by two qualities of waste activated sludge (SLB50 y SLB90) and with a mixture of two co-substrates: cattle manure (CEV50 y CEV90) and residual edible oil with mixing, pH and temperature control. Bacteria in good quality sludge (SLB90) showed a faster adaptation of 2 days than those in low quality (SLB50) with 25 days lag phase. The highest CH4 production was for SLB90 (303.99cm3 d-1) compared to SLB50 (4.33 cm3 d-1); while cow manure sludge mixture (CEV90) contributed to increasing production of CH4 (42 422.8 cm3 d-1) compared to CEV50 (12 881.45 cm3 CH4 d-1), while in residual edible oil mixture they were 767.32 cm3 d-1 and 211.42 cm3 d-1 for CAV90 y CAV50, respectively. The addition of sludge co-substrates improves the nutrient balance, C/N rate and micro flora diversity; consequently methane production improves too; this methodology could be integrated into concepts of Circular economy.

The rapid growth of the global population is causing a significant increase in waste production, leading to serious environmental and public health challenges. To address these issues, waste management systems are incorporating advanced technologies. Machine learning and computer vision are used to predict waste patterns, optimize collection schedules, and improve sorting accuracy. Deep learning automates the sorting process, provides predictive analytics, and enhances recycling rates. Robotics, combined with AI and computer vision, improves sorting efficiency, while the Internet of Things (IoT) monitors waste levels and optimizes collection routes. Despite these benefits, challenges such as data scarcity, high computational demands, and the need for substantial infrastructure investments must be addressed. This research explores the integration of advanced technologies into waste management and evaluates their effectiveness using waste datasets. It highlights the potential to tackle environmental challenges and lay the groundwork for more intelligent waste management solutions.

Recent efforts to conceptually design a technologically meaningful electromagnetic retarded engine indicated that this can only be done using the immense charge and current densities which exist in the atomic scale. However, this scale cannot be described by Newtonian physics, and only a quantum description will suffice to describe the dynamics of an electron on this scale properly. Here we study the retarded field quantum engine and highlight the differences between the quantum and the classical retarded engines.

Nowadays, the fingerprinting methodologies of olive oils are dominated. They consider the entire analytical signal, which is acquired and recorded by the analytical instrument, directly from olive oil or isoleted fraction, i,e chromatogram. The shape and intensity of the recorded signal the instrumental fingerprint from the whole olive oil adulteration. Therefore, the methodolygy is based on the chemical composition (Fatty acids and Triglycerides compositions). However, Fatty acids composition as an indicator of purity suggests that linolenic acid content could be used as a parameter for the detection of extra virgin olive oil fraud with 5% of soybean oil. The adulteration could also be detected by the increase of the trans-fatty acid contents with 3% of soybean oil, 2% of corn oil and 4% of sunflower oil. The use of the ∆ECN42 proved to be effective in the Chemlali extra-virgin olive oil adulteration even at low levels: 1% of sunflower oil, 3% of soybean oil and 3% of corn oil. Therefore, compared to classical methods PCA and new approach of using LDA application could represent an alternative and innovative tool for faster and cheaper evaluation of extra-virgin olive oil adulteration.

The aim of this study was utilization of ground tea waste (GT) left after brewing the black tea as a biofiller of natural rubber (NR) composites. Ionic liquids (ILs), i.e., 1-ethyl-3-methylimidazolium lactate and 1-benzyl-3-methylimidazolium chloride, often used to extract phytochemicals from tea, were applied to improve the dispersibility of GT particles in elastomeric matrix. The influence of GT loading and ILs on curing characteristics, crosslink density, mechanical properties, thermal stability and resistance of NR composites to thermo-oxidative aging was investigated. The amount of GT did not significantly affect curing characteristics and crosslink density of NR composites, but had serious impact on tensile properties. Applying 10 phr of GT improved the tensile strength by 40% compared to unfilled NR. Further increasing in GT content worsened the tensile strength due to the agglomeration of biofiller in elastomer matrix. ILs significantly improved the dispersion of GT particles in elastomer and increased the crosslink density by 20% compared to the benchmark. Owing to the poor thermal stability of pure GT, it reduced the thermal stability of vulcanizates compared to unfilled NR. Most importantly, GT-filled vulcanizates showed improved resistance to thermo-oxidative aging, since the aging factor increased by 25% compared to the unfilled vulcanizate.

Infill drilling is one of the most effective methods to improve the performance of poly-mer flooding. The difficulties related to infill drilling are determining the optimal numbers and placements of infill wells. In this study, an improved archimedes optimization algorithm with Halton sequence (HS-AOA) was proposed to overcome the aforementioned difficulties. First, to optimize the infill well placement for polymer flooding, an objective function that considered the economic influence of infill drilling was developed. Then, the novel optimization algorithm (HS-AOA) for infill well placement was developed by combining the AOA with the Halton se-quence. The codes were developed in MATLAB and connected to a commercial reservoir simula-tor CMG STARS to carry out the infill well placement optimization. Finally, the HS-AOA was compared to the basic AOA to confirm its reliability and then used to optimize the infill well placements for polymer flooding in a typical offshore oil reservoir. The results showed that the introduction of the Halton sequence into AOA effectively increased the diversity of the initial ob-jects in the AOA and avoided the HS-AOA trapping into the local optimal solutions. The HS–AOA outperformed the AOA. It was an effective approach to optimize the infill well placement for polymer flooding processes. In addition, infill drilling could effectively and economically im-prove the polymer flooding performance in offshore oil reservoirs. The NPV of the polymer flooding case with infill wells determined by HS-AOA reached 3.5 × 108 $, which was an increase of 7% over that of the polymer flooding case. This study presents an effective method for opti-mizing infill well placement for polymer flooding processes. It also can serve as a valuable refer-ence for other optimization problems in the petroleum industry, such as joint optimization of well control and placement.

In Tunisia, olive is the most cultivated fruit crop while in the north where rainfall exceeded 400mm.year-1, the olive growing area is in widely extension in marginal soil with high slope gradient. Thus, the inclusion of cover crops is a sustainable solution to increase the ecosystem productivity, improve the soil fertility and oil yields. But, in Tunisia a few study were investigated the effect of legumes cover crop on the olive productivity. Therefore, the aim of this study was to evaluate the short-term (two cropping seasons s 2021 and 2022) effects of different seeded cover crops and soil management practices on the cover crops and soil characteristics, as well as enzymes activities and related microbial diversity. Six intercropping were tested in rainfed olive orchards (cv.Chétoui): Spontaneous vegetation (Spont), Wheat, Vetch, Oat, Fenugreek, mixture Vetch-Oat and compared to control (3 periodic tillage/year without intercropping). During the first cropping season, cover crops were cut as animal feed and only residues were incorporated into the soil. While, during the second year, all cover crops biomass were incorporated into the soil. Results indicate that the dry biomass and carbon uptake were significantly higher in grasses species (Wheat and Oat). But, highest level of nitrogen was found in Fenugreek cover crops. As compared to control, all cover crops including spontaneous vegetation increased soil organic matter and macronutrient level, mainly phosphorus. The most activity of β-glucosidase, phosphatase and arysulphatase was found in the cover crops plot of wheat and oat. In addition, this study improve that the utilization of the carbon sources was dominated by amides, amine and amino-acids in the fenugreek plot; while it was dominated by polymers and carboxylic acids in the case of wheat and oat.

Nowadays, the high demand for healthy foods and sustainable products, has led the food industry to explore innovative food technologies, such as fortification with bioactive compounds like antioxidants and polyphenols, that may be sourced from herbs or by-products. The aim of the present study was to explore the enrichment of refined olive oils with natural bioactive compounds such as the herbs rosemary (salvia rosmarinus), basil (ocimum basil), sage (salvia officinalis), lemon balm (melissa oficinallis), st. john’s wort (hypericum perforatum), pink savory (Thymbra satureja), dittany (origanum dictamnus), and by-products such as pomace from olives, olive leaves (olea europaea tree), orange peel (citrus sinensis), lemon peel (citrus limon), pomegranate peel (punica granatum) and mandarin peel (citrus reticulate). The fortification of the refined olive oils was performed with the use of different methodologies such as Conventional maceration (CM), Incubation shaking maceration (ISM), and Ultrasound assisted maceration (UAM). Their phenolic content and antioxidant capacity were measured with Folin–Ciocalteu assay and Ferric Reducing Antioxidant Power (FRAP) assay respectively. All methods demonstrated that different parameters such as time of maceration, temperature and sample concentration, play an important role in the fortification process of the refined olive oils. The predicyed bioavailability of the antioxidant and phenolic compounds in the fortified oils was determined with in vitro digestion and ranged from 4.84% to 53.11%. Furthermore, the refined olive oils fortified with pomace, basil, st. john's wort, and pomegranate peel presented the highest antioxidant and phenolic predicted bioavailability indices during the in vitro process compared to the control refined olive oil. Finally, fortification with natural herbs or by-products can be considered an innovative method for the improvement of the nutritional value of refined olive oils.

This article deals with special curves similar to those known in mathematics as Lamé curves. Their equations have a certain similarity with the equations of Lamé curves. But these curves are more like ellipses in appearance. Like ellipses, they have major and minor axes. These are such curves that their major and minor semi-axis coincide with an ellipse but are different than an ellipse. The main feature of these curves is that for any triangle whose base coincides with the axis of a given curve and the vertex is on a given curve, the condition aⁿ+bⁿ=cⁿ is obtained. The number “n” is called the degree or rank of this curve. To distinguish this group of curves, we called them Elbe curves. The equations of these lines are also provided in the paper.

Aiming at solving difficulties related to aero-engine classification and identification, the infrared spectra of aero-engine hot jets are measured by telemetry Fourier transform infrared spectrometer, and a six types aero-engine hot jet spectrum data set is generated. The spectrum data set were randomly sampled at a ratio of 8:1:1 to generate training set, validation set and prediction set. In this paper, a Peak Finding Siamese Convolutional Neural Network (PF-SCNN) is designed to match and classify spectrum data. In the first place, the matching pairs of training set and validation set are made independently with the labels of positive and negative samples creating. The spectrum feature extraction and distance similarity calculation are carried out by the Siamese convolutional neural network (SCNN). When entering the prediction phase, the prediction set and training set are integrated to predict in the trained model. The prediction set labels are ultimately determined by matching them with the training set labels having the highest similarities to ensure accurate predictions. To improve the operation efficiency of the SCNN, a peak finding method is introduced to extract the spectrum peaks. Peak positions of high frequency are counted, while the peak data are extracted. The peak data are used to take the place of the original data for training and prediction. The performance measures are defined as Accuracy, Precision, Recall, Confusion matrix and F1-score, and the prediction accuracy was up to 99%. The experimental results indicate that the proposed PF-SCNN is suitable for our spectral dataset and can complete the task of infrared spectrum classification of aero-engine hot jets.

The existing methods of oil palm Fresh Fruit Bunch (FFB) evacuation from in-field to temporary collection point which typically apply medium to large tractors, often result in unexpected soil compaction. Meanwhile, smaller size equipment indicates low working capacity and unable to perform direct unloading to collection bin. This paper addresses the challenge of FFB evacuation by focusing on preventing soil compaction, increasing working capacity and enabling direct unloading to collection bin. For this purpose, a 6x6WD transporter prototype with a scissor lift mechanism was developed. With the design, the transporter could evacuate FFB in both steep mineral terrain and low ground pressure peatland, able to carry FFB with capacity of 750 kg and provide direct unloading into collection bin. The average field working capacity of the transporter was found to be 15 tons day-1. This research offers insights for future designs of medium-sized FFB transporters with advanced unloading mechanisms.

This study addresses the pressing need for flood extent and exposure information in data-scarce and vulnerable regions, with a specific focus on West Africa, particularly Senegal. Leveraging the Google Earth Engine (GEE) platform and integrating data from Sentinel-1 SAR, Global Surface Water, HydroSHEDS, Global Human Layer Settlement, and MODIS Land Cover, our primary ob-jective is to delineate flood extents and compare them with centennial flood-prone areas, offering a comprehensive assessment of exposure during the period from July to October 2022 across Sen-egal's 14 regions. The findings underscore a total inundation area of 2 951 square kilometers, impacting 297 142 people, 175 square kilometers of urban and 16 square kilometers of crops. Notably, August wit-nessed the largest flooded areas, reaching 780 square kilometers, constituting 0.40% of the coun-try's surface. Subsequent regions, including Saint-Louis, Ziguinchor, Fatick, and Matam, experi-enced varying extents of flooding, with August data showing a 1.34% overall overlap compared to centennial flood-prone areas derived from hydrological and hydraulic modeling. This low per-centage reveals the distinct purposes and natures of the two approaches (remote sensing and modeling), as well as their complementarity. Turning to flood exposure, August emerges as the most critical month, affecting 76 595 people (0.43% of the total population). Dakar, Diourbel, Thiès, and Saint-Louis regions bore substantial impacts, affecting 100 707, 57 648, 31 579, and 26 581 people, respectively. These findings emphasize the imperative for comprehensive disaster preparedness and mitigation efforts. The study provides a crucial national-scale perspective to guide Senegal's authorities in formulating effective flood management, intervention, and adaptation strategies.

Endocrine disruptors are molecules that can interfere with the proper functioning of the endocrine system and lead to harmful effects in living organisms. This review focuses on the impact of synthetic fragrances, which are commonly found in personal care and household products, on the endocrine system. The article discusses the different types of hormones in the body and how they interact with receptors to produce signals. It also explores how endocrine disruptors can interfere with hormone signaling and transport, leading to adverse effects in the body. This work underscores the crucial need for further research into the impact of synthetic fragrances on the endocrine system and the importance of using safer alternatives in personal care and household products.

Hybrid power plants have recently emerged as reliable and flexible electricity generation stations by combining multiple renewable energy sources, energy storage systems (ESS), and fossil-based output. However, the effective operation of the hybrid power plants to ensure continuous energy dispatch under challenging conditions is a complex task. This paper proposes a dispatch engine (DE) based on mixed-integer linear programming (MILP) for the planning and management of hybrid power plants. To maintain the committed electricity output, the dispatch engine will provide schedules for operation over extended time periods as well as monitor and reschedule the operation in real-time. Through precise prediction of the PV and wind power output, the proposed approach guarantees optimum scheduling. The precise prediction of the PV and wind power are achieved by employing a predictor of Feed-Forward Neural Network (FFNN) type. With such a dispatch engine, the operational cost of the hybrid power plants, and the use of diesel generators (DGs) are both minimized. A case study is carried out to assess the proposed dispatch engine feasibility. A real-time measurement data pertaining to load, wind, and PV power outputs is obtained from different locations in the Sultanate of Oman. The real-time data is utilized to predict the future output power from PV and the Wind farm over 24 hours. The predicted powers are then used in combination with a PV-Wind-DG-ESS-Grid hybrid plant to evaluate the performance of the proposed dispatch engine. The proposed approach is implemented and simulated using MATLAB. The results of the simulation reveal the proposed Feed-Forward Neural Network’s (FFNN) powerful forecasting abilities. In addition, the results demonstrate that adopting the proposed DE can minimize the use of DG units and reduce plant running expenses.

Silica fly ash, Certyd aggregate, and an alkaline solution were used to produce lightweight geo-polymer concretes. The compressive strength, water absorption, bulk density and SEM photos showing the structure of the obtained composite were carried out. Tests conducted on the specifi-cation of lightweight geopolymer concretes have revealed significant chemical interactions between the ash aggregate and the geopolymer mortar, particularly when the coarse aggregate surface has been pre-treated with an alkaline solution. Statistical analysis of the experimental data, which in-vestigated the influence of three key variables on compressive strength, water absorption, and bulk density of Lightweight Geopolymer Concrete (LBG), identified the following factors as having the most substantial impact: the quantity of alkali used, the curing temperature, and the concentration of alkali in the mixture. The optimal test series exhibited a commendable compressive strength of 20.14 megapascals (MPa), accompanied by a water absorption rate of 14.72% and a bulk density of 1486.6 kilograms per cubic meter (kg/m³). These findings underscore the importance of alkali con-tent, curing temperature, and alkali concentration in tailoring the properties of lightweight geo-polymer concrete to meet specific performance requirements.

The utilization of natural waxes to form oleogels has emerged as a new and efficient technique for structuring liquid edible oil into solid-like structures for diverse food applications. The objective of this study was to investigate the interaction between sunflower wax (SW) and monoglycerides (MGs) in olive oil oleogels and to assess their physical characteristics and storage stability. To achieve this, pure SW and a combination of SW with MGs in a 1:1 ratio were examined within a total concentration range of 6-12% w/w. The formed oleogels were characterized based on their microstructure, melting and crystallization properties, textural characteristics, and oxidative stability during storage. All the oleogels were shelf-stable, and as the concentration increased, the hardness of the oleogels also increased. The crystals of SW oleogels were long needle-like, while the combination of SW and MGs led to the formation of crystal aggregates and rosette-like crystals. The differential scanning calorimetry and FTIR showed that the addition of MGs led to different crystal structures. The oxidation results revealed that oleogels had low peroxide and TBARS values throughout the 28-day storage. These results provide useful insights about the utilization of SW and MGs oleogels for potential applications in the food industry.

Ammonium sulfate has been utilized in agriculture; however, there is a dearth of research on its application in maize cultivation subsequent to the implementation of nitrification inhibitors or coating. This study aims to analyze the impacts of various combinations of ammonium sulfate fertilizers on soil nutrients, plant nutrient uptake, yield, and fertilizer utilization efficiency in maize cultivation to ascertain the optimal and stabilized disposal method for ammonium sulfate. A completely randomized design was employed with five treatments (AU, the control using urea; AS, treatment using ammonium sulfate; ASN, treatment using ammonium sulfate with a nitrification inhibitor; ASG, treatment using oil-coated ammonium sulfate; ASD, treatment using oil-humic acid-coated ammonium sulfate). Results showed that: (1) Compared with AU and AS, ASN, ASG and ASD decreased the leaching rates of TN, NH4+-N and NO3-N to the 10-20 cm soil layer, and more residual N was obtained in 0-10 cm soil layer. The first-order kinetic equation Nt=N0(1-e-kt) can better fit the process of nitrogen accumulation and release, and the N release rate constant is AU>CK>AS>ASH>ASN>ASD; (2) Compared with AU and AS treatments, the plant dry weight, grain dry weight, spike width, spike length, and yields of maize increased by 8.85-11.08%, 12.98-14.15%, 2.95-3.52%, 5.50-5.65%, and 43.21-51.10% under ASG treatment respectively. The impact of effective spike number on maize yield was found to be significant, as demonstrated by the path analysis conducted in this study. Furthermore, the accumulation levels of nitrogen, phosphorus, and potassium within above-ground plants significantly increased under the ASG treatment compared to the AU and AS treatments. The partial productivity of nitrogen, phosphorus, and potassium increased by 1.43-1.51-fold under ASG treatment, while grain nitrogen balance, grain phosphorus balance, and grain potassium balance increased by 1.41-1.58-fold, 1.51-1.95-fold, and 1.15-l.96-fold respectively. The oil-coated ammonium sulfate, therefore, exhibited the optimal slow-release effect of nutrients, thereby achieving superior performance in enhancing maize production and efficiency.

Hybrid electric vehicles (HEVs) are perceived as a first step towards the future of sustainable transport. Of course, battery electric vehicles (EVs) are currently ideal for what is wanted to stand for transport in the future. The lack of infrastructure for these vehicles makes many potential users choose hybrid vehicles in these conditions. This paper analyzes the influence of the engine and electric motor of hybrid vehicles on their performances. Three engines with slightly different power and close characteristics were considered for configured models. Also, two electric motors with very different power but having a very close maximum continuous torque have been used in models. One is an induction motor, and the other is a permanent magnet synchronous motor. ADVISOR software has been used for vehicles configuration and simulation. Series and parallel hybrid vehicles have been considered. The main dynamic performances and the fuel consumption in two driving cycles were compared for the configured models. Three conventional models with the same engines used in HEVs have also been simulated for reference. The results highlight that in the case of HEVs, the choice of combination engine/electric motor is crucial in obtaining the best report between dynamic performances and low fuel consumption, and implicitly a low negative impact on the environment.

This study proposes and validates a novel combustion control system for Oil-Fired Boilers aimed at reducing air pollutant emissions through flame image prediction. The proposed system is easily applicable to existing ships. Traditional proportional combustion control systems supply fuel and air at fixed ratios according to the set steam load, without considering the emission of air pollutants. To address this, a stable and immediate control system is proposed, which adjusts the air supply to modify the combustion state. The combustion control system utilizes oxygen concentration predictions from flame images via SEF+SVM as control inputs, and applies Internal Model Control (IMC)-based Proportional-Integral (PI) control for real-time combustion control. Due to the complexity of modeling the image-based system, IMC parameter tuning through experimentation is essential for achieving effective control performance. Experiments conducted on a 3000 kg/h marine oil-fired boiler in actual operation optimized the controller parameters for stability and responsiveness, and validated their effectiveness. The results demonstrate the potential of the proposed system to improve combustion efficiency and reduce emissions of air pollutants. This study provides a feasible and effective solution for enhancing the environmental performance of marine oil-fired boilers. Given its ease of application to existing ships, it is expected to contribute to sustainable air pollution reduction across the maritime environment.

(1) Background: Food waste (FW) in Romania is 70 Kg/capita/year, while 70% of food waste comes from public catering, retail services, and households (over 50% – 47 million tons). (2) Methods: A cross-sectional observational study was conducted using an online questionnaire via the Google Forms platform from 15 April 2023 to 15 May 2023. The questionnaire was designed to assess various aspects, such as some socio-demographic information (age, sex, occupation, area of residence, study level, household members number, children < 18 years of age); the personal involvement and frequency of food purchases and homemade food cooking; the main sources that generate food waste; the motivation and frequency with which food waste occurs; the level of awareness regarding the impact of food waste; the respondents' intentions regarding sustainable behaviors and practices food management; the level of information and familiarity of the respondents with the notions of validity and how these may influence their food consumption decisions. (3) The results show that FW incidence is occasionally (42%), very rarely (43.33%), frequently (15%), and no food waste was reported by 2.66% of respondents. The [35-44] age category records the highest FW frequency, followed by [18-24]. The most wasted are homemade food (29.67%), bread and bakery products (27.00%), and fruits and vegetables (14.33%). High involvement in purchasing and buying food following a previously established list reduces FW frequency. The same is valid for high daily involvement in food and homemade cooking. High interest in the FW problem and its perception as a waste of money leads to diminishing it, while guilty feelings increase the FW level (37.50% to 73.33%). (4) Conclusions: The present study shows that household food waste management is a multifactorial process that involves numerous socio-demographic, behavioral, and emotional aspects. Extensive data analysis supports our results, revealing deep self-reported information details and confirming its complex approach.

This study presents the evaluation of an ion exchange resin-based installation designed for the recycling of engine coolants, specifically ethylene glycol (EG) and propylene glycol (PG). The recycling process aims to restore the coolant to meet the stringent ASTM standards for both new and recycled coolants. A combination of physical-chemical methods, gas chromatography-mass spectrometry (GC-MS), and inductively coupled plasma mass spectrometry (ICP-MS) was employed to analyze and validate the purity and performance of the recycled product. The experimental setup included performance tests to assess the efficacy of the recycled coolants in comparison to new coolant standards. The results demonstrate that the recycled EG coolants exhibit comparable quality to new coolants, with all critical parameters falling within the acceptable ASTM limits. This indicates that the ion exchange resin method is a viable and efficient solution for the recycling of engine coolants, offering an environmentally friendly alternative to the disposal of used coolants while ensuring compliance with industry standards.

Households and businesses are generating unprecedented levels of electrical and electronic wastes (e-waste), fueled by modernisation and rapid obsolescence. While the challenges imposed by e-waste are similar everywhere in the world, disparities in progress to deal with it exists; with developing nations such as South Africa lagging. The increase in e-waste generation increases the need to formulate strategies to manage it. This paper presents an overview of e-waste management on a global and South African scenarios with a specific case for Cathode Ray Tube (CRT) waste management practices in South Africa. CRTs present the biggest problem for recyclers and policy makers because they contain hazardous elements such as lead and antimony. Common disposal practices have been either landfilling or incineration. The research into the South African practices with regards to CRT waste management showed that there is still more to be done to effectively manage this waste stream. This is despite clear waste regulatory frameworks in the country. However, recent developments have placed e-waste as a priority waste stream, which should lead to intensified efforts in dealing with it. Overall, these efforts should aim to maximise diversion from landfilling and to create value-addition opportunities, leading to social and environmental benefits.

In an attempt to reuse fibrous textile waste and, at the same time, to address dye pollution in textile wastewater, waste cotton-based yarn was utilized as both a cheap and sustainable adsorbent and a precursor for carbon adsorbent production. Cotton and cotton/polyester yarn samples underwent thermal modification through carbonization followed by chemical activation with KOH. Various techniques including nitrogen adsorption-desorption isotherms, scanning electron microscopy, Fourier transform infrared spectroscopy, and surface charge determination were employed to analyze the morphological and surface properties of the cotton-based adsorbents. Adsorption properties were evaluated by testing the removal of selected cationic and anionic dyes from water. The impact of temperature, contact time, initial concentration, and pH of the adsorbate solution on adsorption was investigated, with experimental data analyzed using theoretical models. While carbonization alone did not significantly enhance adsorption properties, activated samples exhibited high efficacy in removing both cationic and anionic dyes from water. Despite the negative influence of the polyester component in the carbon precursor on the efficiency of activated samples in removing methyl orange, results indicated that activated cotton and cotton/polyester yarn could be used to prepare highly efficient adsorbents for the rapid removal of methylene blue from real wastewater samples.

The management of waste cooking oil (WCO) often poses significant challenges. Improper disposal of WCO results in negative environmental impacts and economic losses. However, from a circular economy perspective, WCO can be recycled and used as a sustainable feedstock for numerous industrial products, replacing virgin vegetable oils. This approach enables the recovery of resources while simultaneously addressing the problem of WCO disposal. By employing a multi-criteria decision analysis (MCDA) approach, the study assesses three alternative recycling pathways for WCO used as a feedstock in the production of A1) biodiesel, A2) biolubricant, and A3) biosurfactant. The aim is to identify the optimal alternative, taking into account environmental, economic, and technical factors. The procedure involved a team of chemical engineers working in the WCO recycling sector who were selected as decision-makers. The 'priority scale' combined with the Paired Comparison Technique was employed as a weighting method to evaluate the selected criteria. The results revealed that the decision-makers considered environmental sustainability as the most crucial evaluation criterion, followed by the economic criterion. In contrast, the aspect of process management was deemed less significant. Among the compared alternatives, utilizing WCO as a feedstock for biosurfactant production was assessed as the optimal WCO recycling solution. This alternative not only demonstrated the lowest coefficient variation but was also deemed the most favourable option. Biolubricant production was determined to be the second-best alternative. The adopted MCDA approach proved to be a reliable and effective tool, enabling the clear identification of the preferred WCO recycling alternative among those assessed. This was achieved through the utilization of the decision-makers' expertise and knowledge.

Nano-emulsions of essential oils (EO) and their chemical constituents are promising raw materials for the ecological control of Tribolium castaneum. Curcuma longa Linn is a plant known for the properties of its rhizome which is used in food, health and hygiene products. Its leaves are by-products with no commercial value, but with unexplored bioactive volatile constituents. This study aims to evaluate the repellency of nano-emulsions containing the EO from leaves of C. longa or its three main chemical constituents against T. castaneum. The representative mixture of EO extracted in four different months showed p-cymene (26.0%), 1,8-cineole (15.1%) and terpinolene (15.5%) as major compounds. Nano-emulsions of EO (HLB 16.7), terpinolene (HLB 15.0), 1,8-cineole (HLB15.0) and p-cymene (HLB 15.0) were repellent at concentrations of 11 μg/cm2 (EO, terpinolene and p-cymene) and 1.1 μg/cm2 (1,8-cineole). The EO nano-emulsion droplet size increased linearly over time, remaining below 300 nm for 35 days and below 600 nm for 80 days. The EO nano-emulsion proved to be a green alternative to synthetic pesticides, as it was safe against the bioindicator Chlorella vulgaris. Terpinolene, 1,8-cineol and p-cymene were able to inhibit the enzyme telomerase from T. castaneum in an in silico assay, which may explain the repellency of these samples. This study provides ideas for the utilization of EO from leaves of C. longa as raw material of new environmentally friendly plant-derived nanobiopesticides.

Heat transfer fluids are used in various industrial systems to maintain them in perfect operating conditions. Extensive research efforts have been dedicated to enhance the thermal properties of these heat transfer fluids to improve their efficiency. Developing nanofluids is a potential candidate for such enhancements. This study investigates the impact of incorporating TiO2 nanoparticles into two types of oils: transformer oil (NYTRO LIBRA) and virgin coconut oil (manufactured by Govi Aruna Pvt. Ltd.) at different temperatures and with varying volume fractions. The nanofluids were prepared using a two-step method by adding CTAB (Cetyltrimethylammonium bromide) surfactant. To minimize nanoparticle agglomeration, this study employed relatively low-volume fractions. Thermal properties by means of thermal conductivity, thermal diffusivity, and volumetric heat capacity were measured in accordance with ASTM (American Society for Testing and Materials) standard methods, using a multifunctional thermal conductivity meter (LAMBDA thermal conductivity meter). The measured thermal conductivity values were compared with theoretical models and previous research findings. It was confirmed that the modification of thermal properties was enhanced by doping TiO2 nanoparticles with different volume fraction.

Regular regimes of oil and oil products pipelines are studied. The problem is to develop an algorithm of effective pipeline system control that ensures the fulfillment of specified boundary conditions at the system boundaries. The product is pumped in batches, the flow is characterized by a change in temperature and pressure flow parameters over time. The developed solution method uses the principle of decomposition in the sense that each computational iteration is im-plemented in 3 stages, in three nested loops. The inner cycle is connected with the material bal-ance relations, at the next cycle the flow equations are introduced and the fulfillment of the 2nd Kirchhoff's law is monitored. If the flow process is significantly affected by temperature, then an external cycle is also implemented, correcting the solution so that the energy conservation equa-tion is satisfied. In the calculation procedure, some computational difficulties may arise, which consist in choosing an appropriate optimization method. On a specific example, the possibility of using various library programs to solve the problem was checked. The developed method is suita-ble for the analysis of systems of arbitrary topology. Since the method is not time-consuming, it can be recommended for online control of oil and oil products supply systems. The paper opens a new direction in the theory of hydraulic circuits. It uses both traditional methods of continuum mechanics and stochastic models.

Organic soil amendments, such as composts, mitigate the environmental burdens associated with wasting organic resources. Although compost application to soil enhances an agroecosystem's capacity to store carbon and produce food, studies investigating the agronomical efficacy and their ability to ameliorate drought stress when used as a soil amendment are minimal. In this study, we produced and used a nutrient rich co-compost through the composting of sludge, a nitrogen-rich organic material with carbon rich municipal solid wastes (MSW) to evaluate the agronomic efficacy of the MSW derived co-compost and their ability to ameliorate drought stress. Application of co-compost significantly enhanced growth and yield of lettuce and maize, by a magnitude comparable to chemical fertilizers. Furthermore, under drought stress, lettuce plants grown under co-compost soil amendment grew much better with less wilting, more biomass and yield, and improved root growth. Also, co-compost application enhanced relative root mass ratio (RRMR) under drought stress, indicative that co-compost amendment increased the allocation of biomass to the roots, which is an important morphological attribute for drought adaptability. K content in both leaves and roots of plants amended with co-compost was also higher under drought stress, which may have played a role in osmotic adjustment, consequently, the plants exhibited higher leaf relative water content (RWC). Other nutrient elements that were significantly enhanced by co-compost application included Mg, Ca, Fe and Cu. These results provide evidence that MSW co-composting could optimize organic resource recycling for climate change mitigation and agricultural productivity while minimizing nutrient losses from agroecosystems.

The antimicrobial resistance to clinically approved antibiotics is rapidly increasing worldwide. Staphylococcus aureus is a critical contributor to deaths associated with antibiotic resistance. In this regard, the search for natural compounds is quite active, that alone or in combination with other agents can be effective as new antibacterial agents. The antibacterial activity of essential oils has presented an increasing interest during the last years and was effective even on multidrug-resistant strains. The present study aims to investigate the interaction effects of oregano essential oil (OEO) with some conventional antibiotics against Staphylococcus aureus tested by agar methods. For this purpose, we selected S. aureus ATCC 29213 and five clinical isolates representative of the species. The essential oil was analyzed using gas chromatography coupled with mass spectrometry (GC-MS). The analysis of the Oregano essential oil revealed the main component to be carvacrol (81,20%). Concentration 2.5% (v/v) OEO was combined with drugs proposed by EUCAST, 2024, specifically penicillin, cefoxitin, erythromycin, gentamycin and tetracycline. The research results showed that the combination of OEO with penicillin, cefoxitin, erythromycin, and tetracycline enhanced the antimicrobial activity of the antibiotics against S. aureus in almost all cases. The area of suppression remained identical (but not smaller) in the unaffected cases. When comparing the effects of the GEN-OEO combination and GEN against most S. aureus strains, a decrease in antimicrobial activity was reported by the diffusion agar method.

Sesame seeds and their edible oil are highly nutritious and rich in mono- and polyunsaturated fatty acids. Bioactive compounds such as sterols, tocopherols, and sesamol provide significant medicinal benefits. The high oil content (50%) and favorable mono-and polyunsaturated fatty acids balance, as well as sesame's resilience to water stress makes, make it a promising candidate for global agricultural expansion. However, sesame production faces challenges such as low yields, poor response to agricultural inputs, and losses due to capsule dehiscence. To enhance yield, traits like determinate growth, dwarfism, high harvest index, non-shattering capsules, and photoperiod sensitivity are needed. These traits can be achieved through variation or induced mutation breeding. Traditional breeding methods often result in unwanted genetic changes. The CRISPR/Cas9 technology has the potential to suppress detrimental alleles and improve the fatty acid profile by inhibiting polyunsaturated fatty acid biosynthesis. Even though sesame is an orphan crop, it has entered the genomic era, with available sequences assisting molecular breeding efforts. This progress aids in associating single nucleotide polymorphisms (SNPs) and simple sequence repeats (SSRs) with key economic traits, as well as identifying genes related to adaptability, oil production, fatty acid synthesis, and photosynthesis. Additionally, transcriptomic studies can reveal genes involved in abiotic stress responses and adaptation to diverse climates. Quantitative trait loci (QTL) mapping can identify loci linked to crucial traits such as capsule size, seed count per capsule, and capsule number per plant. This paper reviews recent advances in sesame breeding, discusses ongoing challenges, and explores potential strategies for future improvement. Hence, integrating advanced genomic tools and breeding strategies provides promising ways to enhance sesame production to meet global demands.

The strategy of any organization is based on the growth of its customer base, and one of 5 its principles is that selling a product to an existing customer is much more profitable than acquiring 6 a new customer. However, this approach has several opportunities for improvement, since it usu- 7 ally has a totally reactive approach, which does not give opportunity to the areas specialized in 8 customer experience and recovery, to give an effective response for that moment, since the customer 9 is gone at the time of the intervention. This happens because usually a diagnostic analysis of cus- 10 tomers who have stopped buying products or services in a defined period, commonly three (3) pe- 11 riods or months, is performed. This thesis work challenges the way to face this problem, and pro- 12 poses the development of a complete solution, which does not focus exclusively on the prediction 13 of churn, as is usually done in the state of the art research, but to intervene in different interactions 14 that can be carried out with customers. The above focused not only to prevent customer churn, but 15 to generate an added value of continuous improvement in sales processes, increase customer pene- 16 tration, leading to an improvement in customer experience and consequently, an increase in cus- 17 tomer loyalty.

Erigeron floribundus (Asteraceae) is an herbaceous plant widely used in the Cameroonian traditional medicine to treat various diseases of microbial and non-microbial origin. In the present study we evaluated the in vitro biological activities displayed by the essential oil obtained from the aerial parts of E. floribundus, namely the antioxidant, antimicrobial and antiproliferative activities. Moreover, we investigated the inhibitory effects of E. floribundus essential oil on nicotinate mononucleotide adenylyltransferase (NadD), a promising new target for developing novel antibiotics, and Trypanosoma brucei, the protozoan parasite responsible for Human African trypanosomiasis. The essential oil composition was dominated by spathulenol (12.2%), caryophyllene oxide (12.4%) and limonene (8.8%). The E. floribundus oil showed a good activity against Staphylococcus aureus (IZD of 14 mm, MIC of 512 µg/mL). Interestingly, it inhibited the NadD enzyme from S. aureus (IC50 of 98 µg/mL), with no effects on mammalian orthologue enzymes. In addition, T. brucei proliferation was inhibited with IC50 values of 33.5 µg/mL with the essential oil and 5.6 µg/mL with the active component limonene. The essential oil exhibited strong cytotoxicity on HCT 116 colon carcinoma cells with an IC50 value of 14.89 µg/mL, and remarkable ferric reducing antioxidant power (TEAC= 411.9 μmol TE/g).

Waste glycerol can be subjected to various processing operations, including purification and re-fining, to obtain glycerol of appropriate purity. In addition, alternative methods of utilising waste glycerol are also being sought, e.g. by converting it into other valuable chemical products or biofuels. Therefore, various technologies are being developed to utilise this type of waste effectively and sustainably. The production of value-added products from waste glycerol is an important issue that determines the improvement of the economic viability of biofuel production and corresponds to the model of a waste-free and emission-free circular economy. This paper characterised the mechanisms and evaluated the efficiency of existing methods of microbiological utilisation of waste glycerol into liquid biofuels, including biodiesel, bioethanol and biobutanol, and identified further directions for the production of value-added products. In addition, a bibliographical analysis of publications re-lated to the production of liquid fuels and economically valuable products from glycerol was carried out, the progress of research and application work was assessed and directions for future research were identified.

Qatar and other Gulf States have a diverse range of marine vegetation that is adapted to the stressful environmental conditions of seawater. The industrial wastewater produced by oil and gas activities adds further detrimental conditions for marine aquatic photosynthetic organ-isms on the Qatari coastlines. Thus, these organisms experience severe stress from both seawater and industrial wastewater. This review discusses the biodiversity in seawater around Qatar, as well as remediation methods and metabolic pathways to reduce the negative impacts of heavy metals and petroleum hydrocarbons produced during these activities. These methods include phyto-stabilization phyto-accumulation, phyto-volatilization, and phyto-degradation. Phy-to-degradation in particular is discussed in detail, including metabolic pathways such as alkane and aromatic-compound degradation pathways. The role of microorganisms that are adjacent to or associated with these aquatic marine organisms is discussed, including rhizosphere biodeg-radation. In this type of biodegradation, exudates are released by plant roots and supply nutrients to microorganisms in the rhizosphere, which enhances their ability to degrade organic pollutants. Special attention is paid to mangrove forests and their roles in remediating shores polluted by industrial wastewater. Seagrasses (Halodule uninervis, Halophila ovalis, and Thalassia hemprichii) and seaweeds (Chlorophyta, Phaeophyta, and Rhodophyta) around the peninsula of Qatar are also discussed.

This research presents a comprehensive framework for efficiently generating forest fire datasets from Google Earth Engine data sources. The primary contribution of this work lies in providing a methodology to swiftly extract forest fire factors without the need for permissions or access to private datasets, rendering the dataset openly accessible and shared without barriers. Furthermore, given that the remote sensing data used is a global dataset, it can be applied in any region without restrictions. In this study, Peninsular Malaysia is chosen as a case study to demonstrate the framework's effectiveness. The generated dataset includes essential variables including the climate and environment, landcover, topography, and anthropogenic factors facilitating the analysis of fire occurrences. The methodology empowers data scientists, enabling them to leverage their analytical skills on the extracted dataset without requiring specialized remote sensing knowledge. Additionally, this study also showcases the adoption of large language models, specifically GPT-4 with the Noteable plugin, as a tool for conducting preliminary analyses on the generated dataset. Sample analyses reveal that several key features, including the KBDI, LST, PDSI, climate water deficit, and precipitation, significantly impact forest fire occurrences in Peninsular Malaysia. Despite the successful application of the GPT-4 with Noteable plugin, certain limitations and challenges are identified, highlighting the necessity for further validation of the tool's applicability and limitations. This study encourages future research to (1) adopt the proposed framework in other regions, (2) explore more detailed analyses encompassing all variables, and (3) leverage machine learning for advanced forecasting.

: The activated carbons (ACs) derived from okara powder waste with high surface areas were modified with ammonia aqueous solution impregnation in an autoclave to enhance their CO2 adsorption properties toward CO2. The impregnated ACs were characterized in which surface chemical composition and properties of the ACs were analyzed by SEM-EDX, FTIR. Activated carbons were functionalized with ammonia aqueous solution (25%) through a hydrothermal process within 24; 48, and 72 hours. The adsorption performance of CO2 onto carbon samples was experimentally evaluated through a TPD CO2 measurement. FTIR spectra confirm the N-containing in N-modified activated carbons and the presence of the –C = O stretch and N-H groups. CO2 uptakes of N-modified activated carbons are 0.24; 1.78; 2.24 and 1.26 mmol/g, which are relatively comparable with those of activated carbons studied in in the literature.

In this work, dry and hydrothermal carbonization (DC and HTC) of RDF pellets were conducted to evaluate the physical, chemical, and fuel properties of the produced chars. In the dry carbonization tests, biomass sawdust was incorporated in different proportions on the samples to minimize agglomeration caused by the melting of the plastic fraction. The experiments were carried out in a temperature of 400°C (DC) and 250-300°C (HTC), in a residence time of 30 minutes. The respective chars and hydrochars were characterized according to their mass yield, apparent density, proximate, elemental, and mineral composition, chlorine content, high heating value, thermogravimetric profile, and surface functional groups. The results showed that dry carbonization of RDF pellets with biomass incorporation, followed by a washing step, resulted in the production of chars with improved properties such as higher fixed carbon and HHV (25-26 MJ/kg) and lower ash and chlorine content. Additionally, the HTC experiments demonstrated that hydrochars showed improved properties without the need for biomass addition and washing, however, with no significant difference in the HHV (20-21 MJ/kg). Therefore, DC of RDF pellets with 10% biomass incorporation seems to be a promising option to overcome the constraints of RDF utilization as an alternative fuel.

The activated carbons (ACs) derived from okara powder waste with high surface areas were modified with ammonia aqueous solution impregnation in an autoclave to enhance their CO2 adsorption properties toward CO2. The impregnated ACs were characterized in which surface chemical composition and properties of the ACs were analyzed by SEM-EDS, FTIR. Activated carbons were functionalized with ammonia aqueous solution (25%) through a hydrothermal process within 24; 48, and 72 hours. The adsorption performance of CO2 onto carbon samples was experimentally evaluated through a breakthrough adsorption experimental setup at room temperature. FTIR spectra confirm the N-containing in N-modified activated carbons and the presence of the –C = O stretch and N-H groups. CO2 uptakes of N-modified activated carbons are 0.24; 1.47; and 1.20 mmol/g, which are relatively comparable with those of activated carbons studied in in the literature.

In this research, catalytic steam reforming acetic acid derived from the aqueous portion of bio-oil for hydrogen production was investigated by using different Ni/ATC (Attapulgite Clay) catalysts prepared by precipitation, impregnation and mechanical blending methods. The fresh and reduced catalysts were characterized by XRD, N₂ adsorption-desorption, TEM and H₂-TPR. The comprehensive results demonstrated that the interaction between active metallic Ni and ATC carrier was significantly improved in Ni/ATC catalyst prepared by precipitation method, and in which the mean Ni particle size was the smallest (~13 nm) resulted in the highest metal dispersion (7.5%). The catalytic performance of the three catalysts was evaluated through the process of steam reforming of acetic acid in a fixed-bed reactor under atmospheric pressure at two different temperatures, such as 550 ℃ and 650 ℃. Results showed that the Ni/ATC (PM-N/ATC) prepared by precipitation method, achieved the highest H₂ yield of ~82% and little lower acetic acid conversion efficiency of ~85% than that (~95%) of Ni/ATC (IM-NATC) prepared by impregnation method. In addition, the deactivation catalysts after reaction for 4 h were analyzed by XRD, TGA-DTG and TEM, which demonstrated that the catalyst deactivation was not caused by the amount of carbon deposition, but owed to the significant agglomeration and sintering of Ni particles in the carrier.

Enhancing the management and monitoring of oil and gas processes demands developing precise predictive analytics techniques. Over the past two years, oil and its prediction have advanced significantly using conventional and modern Machine Learning techniques. Several review articles detail the developments in predictive maintenance and technical and non-technical aspects of influencing the uptake of big data. The absence of references for machine learning techniques impacts the effective optimization of predictive analytics in the oil and gas sector. This review paper offers readers thorough information on the latest machine learning methods utilized in this industry's predictive analytical modelling. The review covers forms of Machine Learning techniques used in predictive analytic modelling from 2021 to 2023 (91 articles). It provides an overview of the details of the papers that were reviewed, comprising of the model’s categories, the data's temporality, field, and name, the dataset's type, predictive analytics (classification or clustering or prediction), the models' input and output parameters, performance metrics, optimal model, and benefits and its drawbacks. Additionally, suggestions for future research directions are provided to raise the potential of the associated knowledge and increase the accuracy of oil and gas predictive analytics models.

Recycling information can be complex and often confusing which may subsequently reduce the participations in any waste recycling schemes. As a result, this research explored the roles as well as the importance of a holistic approach in designing recycling information using 15 expert-based in-depth interviews. The rationale was to offer a better understanding of what constitutes waste, recycling, and how recycling information should be designed and presented to make recycling more attractive/convenient. Based on the research participants’ perceptions with supports from the existing studies, this research sub-categorised recycling information into three different themes, termed the “WWW” of recycling information components. As a result, these components (or attributes) were extensively described (using findings of semi-structured interviews) to elicit pragmatic guidance for practitioners, policy-makers, and other stakeholders in designing structured communication or information strategies that may simplify and subsequently increase waste-recycling practices. The policy implications of holistic information in enhancing recycling are further discussed.

Silver ion (Ag+) are recognized for their potent antibacterial properties; however, their utilization in food preservation is restricted by factors such as inadequate stability, a transient antibacterial impact, and the potential for human absorption. Hydrogel-based antibacterial agents are capable of exerting their antibacterial effects by establishing appropriate microenvironments, which facilitate the efficient delivery of antimicrobial molecules to the contaminated regions of food. In previous studies, we observed that chitosan (CS) and silver nitrate (AgNO3) were able to reduce Ag+ to silver nanoparticles (AgNPs) with enhanced antibacterial properties. This not only significantly extended the stability of the antibacterial agent but also demonstrated exceptional inhibitory capabilities against pathogenic bacteria, including common grape contaminants such as P. expansum, A. niger, and B. cinerea. Utilizing ultrasound-induced complexation technology, this study has successfully synthesized a chitosan-silver (CS-AgNPs) hydrogel. The efficacy of this hydrogel against the pathogenic fungus responsible for jujube black spot disease has been thoroughly investigated. The morphology structures of CS-AgNPs hydrogels were characterized by TEM, FTIR and UV-vis. The results indicated that AgNPs ranging from 80 to 110 nm were uniformly dispersed within the gel matrix and remained stable for extended periods at room temperature. In vitro antibacterial assays and fractional inhibitory concentration index (FICI) studies revealed that the pronounced antibacterial efficacy of the CS-AgNPs hydrogel was primarily attributed to the additive antibacterial effect of CS and AgNPs. These insights underscore the significant potential of CS-AgNPs hydrogels in combating fungal diseases of jujube, offering innovative strategies and materials for the management of agricultural pathogens.

The aim of this study was to investigate the physicochemical characterization and biological activities of chitosan (CH) based composite films with the incorporation of chestnut flower essential oil (CFEO). The composite films were prepared by casting method and characterized in terms of structural, morphological and mechanical properties via FT-IR, XRD, UV, SEM and TGA. The results proved the significantly increased water vapor permeability (WVP), heat resistance, antibacterial and antioxidant capabilities of CH-CFEO films. The incorporation of CH and CFEO enhanced the UV blocking, which made the film shield almost all UV light. Films with the tensile strength of 6.37 ± 0.41 MPa and elongation at break of 22.57 ± 0.35% were got with 6 mg mL-1 CFEO. Subsequently, the fruit preservation experiments also confirmed that the composite films could effectively extend the shelf life of bananas through their excellent water vapor and oxygen barrier. These desirable performances enable our newly developed composite films to be a remarkable packaging material to solve the fresh fruit preservation dilemma.

Pipelines extend thousands of kilometers to transport and distribute oil and gas. Given the challenges often faced with corrosion, fatigue, and other issues on steel pipes, the demand for glass fiber reinforced plastics (GFRP) pipes is increasing in the oil and gas gathering and transmission systems. However, the medium transported through these pipelines contains multiple acid gases such as CO2 and H2S, as well as ions including Cl-、Ca2+、Mg2+、SO42-、CO32- and HCO3-. These substances can cause a series of problems, such as aging, debonding, delamination, and fracture. In this study, a series of aging damage experiments were conducted on V-shaped GFRP pipes with depths of 2mm and 5mm. The aging and failure of GFRP were studied under the combined effects of external force and acidic solution using acoustic emission (AE) techniques. It was found that the acidic aging solution promoted matrix damage, fiber/matrix desorption, and delamination damage in GFRP pipes over a short period. However, the overall aging effect was relatively weak. Based on the experimental data, the SSA-LSSVM algorithm was proposed and applied to the damage pattern recognition of GFRP. An average recognition rate of up to 90% was achieved, indicating that this method is highly suitable for analyzing AE signals related to GFRP damage.

Gas turbine engines are widely used in various industries such as aviation, power generation, and marine propulsion due to their high efficiency and reliability. The combustion chamber of a gas turbine engine design contains a number of elements, including as the chamber's size and form, the fuel injection system, the ignition system, and the cooling system and it plays a critical role in the performance and efficiency of the engine. This research discusses the fabrication of a combustion chamber model for a gas turbine engine. The aim of this research is to develop a combustion chamber that is cost-effective, easily available, and can be fabricated in less time. The research covers the different types of combustion chambers used in gas turbine engines and compares their advantages and disadvantages. It then selects the best type of combustion chamber for the gas turbine engine based on its cost, availability, and fabrication time, Efficiency and high power to fuel ratio. The report also describes the fabrication process involved, including the techniques and materials used, along with safety precautions and environmental protection measures. Lastly, the research suggests future improvements and potential applications for the fabricated combustion chamber model.

.Various synthetic nematicides are currently used effectively in the control of plant parasitic nematodes. However, these nematicides have adverse effects on humans and the environment. Neem oil is eco-friendly alternatives to synthetic nematicides. The effectiveness of repeated neem oil application in suppressing the root-knot nematodes infestation in figs seedlings was therefore examined in this study, both in its natural form (10 ml/L) and in its nano-emulsion form (5 and 7 ml/L). The recorded reduction parameters of M. incognita were J2/250g soil, galls and egg masses / 5g roots of infected fig seedlings were measured at that time, and the effects of these natural additives were compared with the Fosthiazate (Krenkel 75%EC). The impact of such soil amendments on some typical plant parameters, the total microbial count of soil, and the overall enzymatic activity of the fig rhizosphere were also included. Obtained results revealed that the soil population density of root knot nematode suppressed by 80.3% , reduction of nematode egg masses (60.4%) due to the application of nano-emulsion of neem oil (at 7ml/L). Present work recommend the use of nano-emulsion of neem oil as one of the effective and eco-friendly means to reduce the root- knot nematode on fig .

Iron is a critical yet limited nutrient for microbial growth. To scavenge iron, most microbes produce siderophores—diverse small molecules with high iron affinities. Different siderophores are specifically recognized and uptaken by corresponding recognizers, enabling targeted interventions and intriguing cheater-producer dynamics. We propose constructing a comprehensive iron interaction network, or "iron-net," across the microbial world. Such a network offers the potential for precise manipulation of the microbiota, with conceivable applications in medicine, agriculture, and industry, as well as advancing microbial ecology and evolution theories. Previously, our successful construction of an iron-net in the Pseudomonas genus demonstrated the feasibility of co-evolution-inspired digital siderophore typing. Enhanced by machine learning techniques and expanding sequencing data, forging such an iron-net calls for multidisciplinary collaborations, and holds significant promise in addressing critical challenges in microbial communities.

The global increase in population has placed significant pressure on food security, leading to the emergence of aquaculture as a vital source of aquatic foods. However, rising costs and the limited availability of fishmeal in aquafeeds have spurred the search for alternative protein sources. While plant-based ingredients have been integrated into commercial aquafeeds, they come with challenges, including low protein content, palatability issues, and the presence of antinutritional factors. In this context, fish silage, derived from fish waste and discarded fish, stands out as a promising alternative technology due to its cost-effectiveness and sustainability attributes. The production of fish silage involves the addition of organic/inorganic acids or lactic acid bacteria to homogenized fish waste. This process yields a valuable mixture rich in peptides, free amino acids, and partially hydrolyzed proteins, offering significant nutritional benefits for animal diets. Beyond its nutritional advantages, fish silage contributes to environmental sustainability by reducing the impact of waste disposal and enhancing the value of fish waste. The objective of this review is to promote sustainable practices in the aquaculture industry in response to the increasing demand for high-quality feed nutrients. To achieve this, it includes an analysis of research results related to silage technology, an appraisal of the advantages and disadvantages of using fish silage as a feed additive, and a focus on emerging trends in this field.

Graphene is perhaps the most prominent “Dirac material,” a class of systems whose electronic structure gives rise to charge carriers that behave as relativistic fermions. In multilayer graphene several crystal sheets are stacked such that the honeycomb lattice of each layer is displaced along one of the lattice edges. When subject to an external magnetic field, the scaling of the multilayer energy spectrum with the magnetic field, and thus the system’s thermodynamic behavior, depends strongly on the number of layers. With this in mind, we examine the performance of a finite-time endoreversible Otto cycle with multilayer graphene as its working medium. We show that there exists a simple relationship between the engine efficiency and the number of layers, and that the efficiency at maximum power can exceed that of a classical endoreversible Otto cycle.