Addressing the significant challenge in high-speed cotton dibbling operations in Xinjiang—specifically, the duck bill’s ("Duck bill" is a type of duck-billed bunch planting mechanism or component). shortened opening duration leading to seed throwing and floating—a new crawler-type delayed hole-forming mechanism has been designed. This mechanism extends the duck bill horizontally, thereby prolonging its opening time, enabling cotton sowing speeds of up to 6 km/h. Following agronomic principles for cotton planting, the overall layout of the crawler-type hole-forming mechanism, the structural parameters of the key components and the trajectory of the hole-forming are determined. We use the Discrete Element Method (DEM) and multi-body dynamics coupling method to simulate and analyze the motion process of the device. The fixed the tilt angle of the duck bill α(A), the depth of the duck bill hole-forming into the soil h(B), and the angle of rotation of the moving duck bill β(C) were taken as the experimental factors, with the longitudinal length of cotton seed hole (Y1) and the hole-forming depth of cotton seed hole (Y2) as the response values. The parameter range of each factor and the preliminary influence on the response value were determined through pre-experiments and single-factor simulation test. Based on RecurDyn-EDEM coupling, a quadratic regression orthogonal rotation combination simulation test was carried out. The results show that the order of the primary and secondary factors affecting the Y1 of the time-lapse hole-forming device was: A > C > B. The order of primary and secondary factors affecting the Y2 of the delayed hole forming device was: B > C > A. When the A was 2.4 °, the B was 42.4 mm, and the C was 30.5 °, the performance of the hole-forming was the best, and the Y1 was 26.4 mm, and the Y2 was 25.0 mm. The bench verification test results show that under the optimized combination of operating parameters, the average Y1 was 29.1 mm, and the average Y2 was 23.2 mm. Compared with the results of the previous coupled simulation model, the average relative errors of the two are 7.23 % and 4.36 %, respectively, indicating the accuracy and effectiveness of the established DEM simulation model and virtual test analysis. The hole-forming area and the opening time of the duck bill after the stable operation of the machine were recorded and measured. The calculated hole dislocation rate Hc was 4.33 %, which did not exceed the national standard requirement of 6 %. The qualified rate of hole distance Hx was 94.33 %, which was much higher than the national standard requirement of 80 %. The average opening time of the duck bill at a speed of 6 km/h is 0.45 s, which is much longer than the time required for cotton seeds to fall from the duck bill 0.11 s. It meets the requirements of high-speed cotton planting in China and facilitating advancements in future high-speed planter technology.

In this study, a new type of temperature sensor device was developed. The circular electrode of the thermal sensitive sensor was modified with TMT and O₂ plasma to enhance the conductivity by forming a thin SnOxCy layer on the electrode surface. The Nano-Au particles were subjected to O₂ plasma pretreatment to form peroxide groups on the surface. The thermally sensitive sensor was made by mixing the above-treated Nano-Au particles with N-isopropylacrylamide (NIPAAm) to form solution and then UV-induced grafting polymerization of the NIPAAm-containing solution onto the electrode substrate. The composite hydrogels on the electrode introduce thermo-sensitive polymeric surface films for temperature sensing. Using ambient environment resistance test to measure the resistance, the LCST (lower critical solution temperature) of Nano-Au (MUA) mixed with NIPAAm hydrogel was found to be 32 °C. At ambient temperatures higher than LCST, the electrode resistance decreases linearly.

Aiming at the problems of high labor intensity and high cost of manual picking, high loss rate of mechanical picking seeds, low mechanization level and difficult to guarantee the quality of picking plates in the process of picking plates of edible sunflower. Based on the principle of manual plate taking, a plate taking control system for sunflower harvesting table was designed. Through the research and analysis of the principle of taking the plate of the edible sunflower harvesting table. According to the actual operation requirements, the overall scheme of the sunflower plate control system is determined, and the control strategy of imitating artificial low loss harvesting is designed. To reduce the grain loss in the process of taking the plate and improve the control accuracy of the system on the movement speed and displacement of the key components in the process of taking the plate, a trapezoidal acceleration and deceleration control algorithm is designed as the control algorithm of taking the plate. To verify the working performance of the plate control system, with the absolute error, relative error and total loss rate of the harvest as objectives. The bench and field verification experiments were both carried out. The bench experiment showed that the speed error of the plate parts was not more than 0.028 m/s. In the bench experiments of the device, the maximum positioning error was 1.25 mm, the average relative error is only 0.94 %, and the grain loss rate was not more than 2.26 %. It result showed that the system algorithm was reliable, the positioning accuracy was high, and the taking plate operation can be completed well. The field verification experiment showed that the forward speed of the unit was in the range of 0.4~0.8 m/s, and the total loss rate of harvest was less than 5 %. When the forward speed is 0.6 m/s, the minimum harvest loss rate is 2.32 %, and which indicated the control system meets the requirements of sunflower harvesting operation.

Weak signal spectral detection is a serious problem in many applications, especially the target possesses certain frequency band and under low signal-to-noise ratio (SNR). A kind of novel technique based on pre-whitening scale-transformation symmetric bistable parallel stochastic resonance (SR) is proposed to solve the problem. Firstly, the pre-whitening can ensure the even distribution of the receiving signal to fit the requirement of SR processing. Secondly, the scale- transformation can help to utilize the weak signal improvement property especially under low frequency band more effectively. Thirdly, the symmetric bistable parallel SR can try to reduce the variance of the clutter and additive noise fluently. Fourthly, by subtracting the steady state re-sponse of the selected symmetric bistable SR system from the parallel SR output, the weak signal spectral detection objective can be realized successfully. Simulation results based on the real sea clutter radar data guarantee the effectiveness and applicability of the proposed symmetric bistable PSR processing approach.

In this work model of mirror elements equilibrium of the micromechanical components is developed, the behavior analysis of the mirror element of micromechanical mirrors in case changing of control voltages of electrostatic actuators is carried out, an expression for determining the maximum value of deflection voltage at which the snap-down effect will take the following form is obtained in case of the influence of the coefficient of the electrostatic rigidity of electrostatic actuators. The developed equilibrium model of mirror elements and the obtained results of modeling can be used at design of micromechanical mirrors with internal suspensions.

Nowadays, Multi-needle electrospinning has used to be an efficient method for producing nanofiber membranes. But in the process, the fluctuation errors in electrospinning fluid flow rate have directly influence the membrane quality, which bringing instability and still have not been solved yet. For finding out the solution to the inaccurate flow control in multi-needle, it is necessary to develop a multi-stage flow runner spinneret for large-scale production of nanofiber membrane. At first, the paper uses the finite element software COMSOL to numerically simulate the polymer flow in the runner of spinneret. Based on it, the velocity field distribution curve was draw and the velocity instability coefficient of the polymer flow was attained, which are providing theoretical guidance for the optimal design of spinneret. Next, the response surface analysis method (RSM) was used to establish a regression model between the average diameter of the nanofiber membrane and the process parameters. Then, above regression model used to perform variance data processing between the average diameter and the process parameter configuration. After that, the 2D and 3D response surface profiles and the significance analysis were completed. Finally, the stability of the nanofibers production was improved, which attained the optimal adjustment of process configuration in multi-needle electrospinning.

Using numerical simulation method, combined with the pre-branch material characteristics of the measurement results, based on the LS-DYNA software to simulate the branch crushing process, the analysis found that not only the existence of the cutter cutting in the branch destruction process, there is also the cutting of the opposing surface of the bending fracture, with the increase in the speed of the knife rollers, the cutter cutting resistance increases, the cutting resistance reaches 2690 N when the cutter at 2500 r/min, the cutter cutting resistance is the smallest in the cutting simulation at the blade angle of 55°, the blade angle is more suitable for the cutting of the branch. In the cutting simulation under different cutting edge angles, the cutting resistance of the tool is the smallest when the edge angle is 55°, which is 1860 N. This edge angle is more suitable for branch crushing and cutting. Using Fluent software to analyse the airflow characteristics of the crushing device, it was found that with the increase of the knife roller speed, the inlet flow and negative pressure of the crushing chamber are increasing, the speed of 2500 r/min, the inlet flow and negative pressure were 1.92 kg/s and 37.16 Pa, which will be conducive to the feeding of branches, but the speed is too high and it will also lead to the enhancement of the vortex of part of the area in the crushing device, which will affect the feeding of branches and the throwing of the crushed material. affect the feeding of branches and the throwing out of crushed materials, and finally determined the speed range of the crushing knife roller is 1800 ~ 2220 r/min. Based on ANSYS/Model module modal analysis of the crushing knife roller, the knife roller of the first six orders of the intrinsic frequency and vibration pattern, crushing knife roller of the lowest order of the modal intrinsic frequency of 137.42 Hz, much larger than the crushing knife roller operating frequency of 37 Hz, the machine will not resonate during operation.

The iron roughneck is an automated equipment utilized for the connection and removal of drilling tools. This paper presents the design of an integrated iron roughneck, providing a detailed introduction to its clamp body structure, along with an analysis of its structural characteristics and performance requirements. The study delves into the integration mode and working characteristics of the clamping mechanism and spin buckle mechanism for the integrated upper clamp body structure of the iron roughneck. Additionally, this paper conducts an in-depth theoretical study on the spin buckle mechanism. Firstly, it analyzes the actual working condition of the spin buckle roller from two perspectives: contact theory and rolling friction theory, determining the structural form of the spin buckle roller. Secondly, it investigates the relative displacement between the spin buckle mechanism and the drilling tool, proposing a design method for the floating device mounted on the spin buckle roller and establishing the kinematic equation of the spin buckle roller under the influence of the floating device. Furthermore, the kinematic equations of the spin buckle roller under the influence of the floating device are established. Finally, a dynamics simulation experiment is performed to simulate the working process of the spin buckle mechanism under actual working conditions, analyzing the dynamics and kinematics of the spin buckle mechanism and obtaining the relevant parameter curves of the spin buckle mechanism and drilling tools. Through data comparison and analysis, the correctness of the theoretical analysis results and the rationality of the performance and structure of the spin buckle mechanism are verified.

Natural polluted insulator surfaces are always coated with various kinds of soluble constituents, and those constituents affect flashover performance differentially. Currently this fact is not considered either in laboratory experiments or field pollution degree measurements, causing the existing insulation selection method to be deficient. In this paper a systematical research on insulator flashover voltage gradient correction involving types of soluble pollution constituents was presented. Taking typical type glass insulator as the sample, its flashover tests polluted by typical soluble chemicals NaCl, NaNO₃, KNO₃, NH₄NO₃, MgSO₄, Ca(NO₃)₂ and CaSO₄ were carried out. Then the flashover gradient correction was made combining the flashover performance of each soluble constituent, the ESDD contribution of the seven constituents, as well as the saturation performance of CaSO₄. The correction was well verified with the flashover test results of insulator polluted by three types of soluble mixture. Research results indicate that the flashover gradient correction method proposed by this paper performs well in reducing the calculating error. It is recommended to carry out component measurements and flashover gradient correction to better select outdoor insulation configuration.

This paper represents the first investigation into the consensus problem of linear time-varying multi-agent systems utilizing an event-triggered communication scheme. First, a general event-triggered consensus control scheme is proposed for a general category of linear time-varying multi-agent systems. Under some suitable assumptions, it is demonstrated that all agents’ states will converge exponentially, with Zeno behaviour being ruled out. Second, the consensus problem in a network of linear time-varying multi-agent systems with a spanning tree is investigated using the proposed control strategy. It demonstrates that the consensus issue for the specified system can be reformulated as a stabilization problem for an error system through a time-varying linear transformation. Then, the event-triggered consensus problem is just a special instance of the general event-triggered consensus problem mentioned above. Finally, to illustrate the efficacy of the event-triggered method proposed in this study, simulation results are shown.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

With the increasing concern of environment, the energy-efficiency scheduling of manufacturing industry is becoming urgent and popular. In turning processes, both spindle speed and processing time can affect the final energy consumption and thus the spindle speed and scheduling scheme need to be optimized simultaneously. Since the turning workshop can be regarded as the flexible flow shop, this paper formulates a mixed integer linear programming model for energy-efficient scheduling of flexible flow shop. Accordingly, a new decoding method is developed by considering of the optimization of spindle speed and scheduling scheme simultaneously, and an estimation of distribution algorithm adopting the new decoding method is proposed to solve large-size problems. The parameters of this algorithm are determined by statistical technique with a simplified practical case. In order to validate the proposed method, a case from practical factories is studied, in which the makespan can be shortened by 25.22%, and the consumed energy can be saved by 5.48%. These results demonstrate the effectiveness of the proposed mathematical model and algorithm.

As the adoption of renewable energy sources grows, ensuring a stable power balance across various time frames has become a central challenge for modern power systems. In line with the "dual carbon" objectives and the seamless integration of renewable energy sources, harnessing the advantages of various energy storage resources and coordinating the operation of long-term and short-term storage have become pivotal directions for future energy storage deployment. To address the complexities arising from the coupling of different time scales in optimizing energy storage capacity, this paper proposes a method for energy storage planning that accounts for power imbalance risks across multiple time scales. Initially, the Seasonal and Trend decomposition using the Loess (STL) decomposition method is utilized to temporally decouple actual operational data. Subsequently, power balance computations are performed based on the obtained data at various time scales to optimize the allocation of different types of energy storage capacities and assess the associated imbalance risks. Finally, the effectiveness of the proposed approach is validated through hourly applications using real-world data from a province in China over recent years.

Background: Complementary and alternative medicines (CAM) are widely used, with pharmacies accounting for a significant share of the distribution market. Despite their popularity, many CAMs lack scientific evidence for effectiveness, and some can cause adverse health effects. Limited research exists on CAM-related adverse events and the effectiveness of CAM labels in conveying crucial information. Methods: This cross-sectional study aimed to investigate CAM utilization, consumer perspectives, and the influence of labels on CAM usage in Melbourne, Australia. Data were collected through an online questionnaire and analysed using descriptive statistics, Pearson's correlation, MANOVA, and regression analyses. Results: The study enrolled 125 current CAM users, primarily recruited from pharmacy and supermarket customers (age: predominantly 31-50; gender: 20.8% male, 79.2% female). Participants' perceptions of effectiveness and safety were positively correlated. Label warnings prompted information-seeking, but consultation with healthcare professionals (HCPs), particularly pharmacists, was infrequent (24%). Adverse reactions were reported by 18.5% of participants, with 8.3% experiencing severe reactions. The analysis revealed relationships between CAM usage and demographics. Ordinal logistic regression showed a significant association between calcium consumption and higher age groups (coefficient = 1.658, p = 0.006), while binary logistic regression identified higher iron consumption among females (coefficient = 2.177, p = 0.007). Conclusions: Label warnings significantly prompted consumers to seek more information about CAMs. However, a limited engagement of HCPs, especially pharmacists, suggests an opportunity for improved consumer education and pharmacist involvement in CAMs-related discussions. The findings highlight demographic influences on CAM usage being essential for developing targeted health interventions and policies. Addressing these aspects may lead to safer CAM practices and informed consumer decision-making.

To make wind power more competitive, it is necessary to reduce turbine downtime and reduce costs associated with wind turbine Operation and Maintenance (O&M). Incorporating machine learning in developing condition-based predictive maintenance methodologies for wind turbines can enhance their efficiency and reliability. This paper presents a monitoring method that utilizes Base Density for the Support Vector Machine (BDSVM) and the evolutionary Fourier spectra of vibrations. This method allows smart monitoring of the function evolution of the turbine. A complex optimal function (FO) for 5-degree order has been developed that will be the boundary function of the BDSVM to timely determine the magnitude, frequency, and place of the failure occurring in wind turbine drive.

Coarse-grained molecular dynamics simulations are employed to investigate the spatiotemporal evolution of vesicles (polymersomes) by the self-assembly of randomly distributed amphiphilic BAB triblock copolymers with hydrophilic A and hydrophobic B blocks in an aqueous solution. The vesiculation pathway consists of several intermediate structures, such as an interconnected network of copolymer aggregates, a cage of cylindrical micelles and a lamellar cage. The cage-to-vesicle transition occurs at a constant aggregation number and practically eliminates the hydrophobic interfacial area between the B block and solvent. Molecular reorganization under-lying the sequence of morphology transitions from a cage-like aggregate to a vesicle is nearly isentropic. The end-to-end distances of isolated copolymer chains in solution and those within a vesicular assembly follow log normal probability distributions. This is attributed to the pre-ponderance of folded chain configurations in which the two hydrophobic end groups of a given chain stay close to each other. However, the probability distribution of end-to-end distances is broader for chains within the vesicle as compared to that of a single chain. This is due to the swelling of the folded configurations within the hydrophobic bilayer. Increasing the hydropho-bicity of the B block reduces the vesiculation time without qualitatively altering the self-assembly pathway.

In the last three decades the presence of phospholipids in the nucleus has been shown and thoroughly investigated. A great interest raised about nuclear inositol lipids mainly because of their role in signalling acting. Here we review the main issues of nuclear phospholipid localization and the role of nuclear inositol lipids and their related enzymes in cellular signaling both in physiological and pathological conditions.

Accurate measurement of water vapor is essential for researches and applications of meteorology, climatology and hydrology. Based on the BeiDou PPP-B2b service, real-time precipitable water vapor (PWV) is retrieved with the precise point positioning (PPP) software. The experiment was conducted in Beijing in January, 2023. Three solutions are designed with PPP using the BeiDou system only, the GPS system only and the BeiDou-GPS combined solution. Real-time PWVs for the 3 solutions are validated with the ERA5 reanalysis data. Between PWVs from single BeiDou and ERA, there are a bias of 0.7 mm and a RMSE of 1.8 mm. While for the GPS case, the bias is 0.73 mm and RMSE is 1.97 mm. The biases are less than 1 mm and RMSEs are less than 2mm. Both the BeiDou and the GPS processing performs very well. But little improvement is found for the BeiDou-GPS combined solution, comparing with the BeiDou system only and the GPS system only solution. This may be due to the poor handling of two different kinds of errors for the GPS and the BeiDou systems in our PPP software. A better PWV estimation with the two systems is to estimate PWV with single system at first step, and then to obtain the optimization by Bayesian model averaging.

The weight coefficients of the diaphragm spring depend on experiences in the traditional optimization. However, this method not only cannot guarantee the optimal solution but it is also not universal. Therefore, a new optimization target function is proposed. The new function takes the minimum of average compress force changing of the spring and the minimum force of the separation as total objectives. Based on the optimization function, the result of the clutch diaphragm spring in a car is analyzed by the non-dominated sorting genetic algorithm (NSGA-II) and the solution set of Pareto is obtained. The results show that the pressing force of the diaphragm spring is improved by 4.09%by the new algorithmand the steering separation force is improved by 6.55%, which has better stability and steering portability. The problem of the weight coefficient in the traditional empirical design is solved. The pressing force of the optimized diaphragm spring varied slightly during the abrasion range of the friction film, and the manipulation became remarkably light.

The G-protein-coupled estrogen receptor (GPER; G protein-coupled estrogen receptor 30, also known as GPR30) is a novel estrogen receptor and has emerged as a promising target for ovarian cancer. GPER, a seven-transmembrane receptor, suppresses cellular viability and migration in studied ovarian cancer cells. However, its impact on the fallopian tube, which is the potential origin of high-grade serous (HGSC) ovarian cancer, has not been addressed. This study was conducted to evaluate the relationship of GPER, ovarian cancer subtypes, i.e., high-grade serous cell lines (OV90 and OVCAR420), as well as potential HGSC ovarian cancer origin (i.e., the fallopian tube cell line FT190). The selective ligand assessed here is the agonist G-1, which was utilized in an in vitro study to characterize its effects on cellular viability and migration. As a result, this study has addressed the effect of a specific GPER antagonist in combination with an agonist on cell viability, providing a better understanding of the effects of these compounds on our diverse group of studied cell lines. Strikingly, attenuated cell proliferation and migration behaviors were observed in the presence of G-1. Thus, our in vitro study reveals the impact of the origin of HGSC ovarian cancers and highlights the GPER agonist G-1 as a potential therapy for ovarian cancer.

Wilms tumor (WT), the most prevalent type of renal cancer in children, exhibits overall survival rates exceeding 90%. However, chemotherapy resistance, which occurs in approximately 10% of WT cases, is a major challenge for the treatment of WT, particularly for advanced-stage patients. In this study, we aimed to discover potential mutation markers and drug targets associated with chemotherapy resistance in advanced stage WT. We performed exome sequencing to detect somatic mutations and molecular targets in 43 WT samples, comprising 26 advanced stage WTs, of which 7 cases are chemotherapy-resistant. Our analysis revealed four genes (ALPK2, C16orf96, PRKDC, and SVIL) that correlated with chemotherapy resistance and reduced disease-free survival in ad-vanced-stage WT. Additionally, we identified driver mutations in 55 genes within the chemo-therapy-resistant group, including 14 druggable cancer driver genes. Based on the mutation profile of the resistant WT samples, we propose potential therapeutic strategies involving platinum-based agents, PARP inhibitors, and antibiotic/antineoplastic agents. Our findings provide insights into the genetic landscape of WT and offer potential avenues for targeted treatment, particularly for patients with chemotherapy resistance.

Rising antimicrobial resistance (AMR) in Salmonella serotypes host-adapted to cattle is of increasing concern to the beef and dairy industry. The bulk of the existing literature focuses on AMR post-slaughter. In comparison, the understanding of AMR in Salmonella among pre-harvest cattle is still limited, particularly in Texas, which ranks top five in beef and dairy exports in the United States; inherently, the health of Texas cattle has nationwide implications for the health of the United States beef and dairy industry. In this study, long-read whole genome sequencing and bioinformatic methods were utilized to analyze antimicrobial resistance genes (ARGs) in 98 isolates from beef and dairy cattle in the Texas Panhandle. Fisher exact tests and elastic net models accounting for population structure were used to infer associations between ARGs and antimicrobial phenotypic profiles and metadata. Gene mapping was also performed to assess the role of mobile genetic elements in harboring ARGs. ARG were found to be statistically different between the type of cattle operation and Salmonella serotypes. Beef operations were statistically significantly associated with more resistance genes compared to dairy operations. Salmonella Heidelberg, followed by Salmonella Dublin isolates, were associated with the most ARGs. Additionally, specific classes of ARGs were only present within mobile genetic elements.

Stroke constitutes a significant public health concern due to its impact on mortality and morbidity. This study investigates the utility of machine learning algorithms in predicting stroke and identifying key risk factors using data from the Suita study, comprising 7,389 participants and 53 variables. Initially, unsupervised K-prototype clustering categorized participants into risk clusters, while five supervised models including Logistic Regression (LR), Random Forest (RF), Support Vector Machine (SVM), eXtreme Gradient Boosting (XGBoost), and Light Gradient Boosted Machine (Light-GBM) were employed to predict stroke outcomes. Stroke incidence disparities among identified risk clusters using the unsupervised K-prototype clustering method are substantial, according to the findings. Supervised learning, particularly RF was a preferable option because of the higher levels of performance metrics. The Shapley Additive Explanations (SHAP) method identified age, systolic blood pressure, hypertension, estimated glomerular filtration rate, metabolic syndrome, and blood glucose level as key predictors of stroke, aligning with findings from the unsupervised clustering approach in high-risk groups. Additionally, previously unidentified risk factors such as elbow joint thickness, fructosamine, hemoglobin, and calcium level demonstrate potential for stroke prediction. In conclusion, machine learning facilitated accurate stroke risk predictions and highlighted potential biomarkers, offering a data-driven framework for risk assessment and biomarker discovery.

This research investigates the complex transformation of the Baltic Clean and Dirty Tankers markets from 1998 to 2023. Our study quantifies the market multifractality in two distinct periods, from 1998 to 2010 and 2010 to 2023. We compare multifractal measures of the original, surrogated, and shuffled data, which indicate high multifractality and a complex market structure influenced by temporal organization and inherent volatility. Shuffled data analysis emphasizes the critical role of temporal sequences within market behaviour. Additionally, the study delves into external factors such as regulatory changes, economic disturbances, technological innovation, and environmental concerns contributing to market complexity. A distinct shift in multifractal values between the two periods suggests an evolution from crisis-induced complexities to a market influenced by diversified and modern dynamics. Our findings offer a concise understanding of the multifractal nature of the tanker markets and how global crises can impact the markets, emphasizing the importance of considering systemic risks in freight market analysis.

Aiming at the problems of high cost of manual pulling, low reliability of existing pulling devices, high breaking rate and high leakage rate in the process of cotton stalk reuse after leaving the field in Xinjiang cotton area, a loosening soil and root-cutting cotton stalk pulling the setting machine has been researched and designed, established the root-cutting force model, calculated and optimized the key parameters of the V-shaped root-cutting knife, and determined the range of slide cutting angle, cutting edge angle and soil entry angle. The shoveling process simulation of V-shaped root-cutting knife and root-soil complex was constructed, and the working mechanism of V-shaped root-cutting knife was clarified. In order to verify the reliability and operation performance of the V-shaped root-cutting knife, the slide cutting angle, cutting edge angle and soil entry angle were used as the test factors, the response surface test of three-factors and three-levels was carried out with root-breaking force and mean value of the cutting resistance as the test index. The test results were analyzed by variance analysis, the significant of influencing factors on the root-breaking force are in a descending order as: slide cutting angle, cutting edge angle, soil entry angle; the degree of influence on the mean value of the cutting resistance are as follows: slide cutting angle, soil entry angle, cutting edge angle. In order to make the V-shaped root-cutting knife achieve the optimal working state, the parameters of the test index were optimized, and the optimal design parameters of the V-shaped root-cutting knife were set as follows: the slide cutting angle was 48.3°, cutting edge angle was 43.4°, and soil entry angle was 26.2°. The field uprooting test showed that the average pass rate of root breakage was 94.8% and the average pull-out rate of the cotton stalk was 93.2%. This study provides theoretical guidance for the development of root breaking mechanism of cotton straw harvester.

To clarify the risk factors for aggravation of esophagogastric varices (EGV) after hepatitis C virus (HCV) eradication with direct-acting antiviral (DAA) therapy, we enrolled 167 consecutive patients with HCV-related compensated cirrhosis who achieved a sustained virological response (SVR) after DAA therapy. During a median of 69 months, EGV was aggravated in 42 (25%) patients despite SVR. The cumulative 1, 3, 5, and 10-year aggravated EGV rates were 7%, 23%, 25%, and 27%, respectively. Multivariate analysis identified platelet count <11.0×10⁴/μL, LSM ≥18.0 kPa, total bile acid ≥33.0 μmol/L, and diameter of left gastric vein (LGV) ≥5.0 mm at HCV eradication as independent risk factors for EGV aggravation post-SVR. In groups that meet all of these risks, the cumulative EGV aggravation rates at 1, 3, and 5 years were 27%, 87%, and 91%, respectively. However, none of the patients who had only one or none of the risk factors experienced EGV aggravation. Platelet count, LSM, total bile acid, and diameter of LGV at HCV eradication were associated with aggravated EGV post-SVR. EGV tends to worsen as two or more of these risk factors increase.

Glycerol represents a useful functional component of heat-transfer fluids. Glycerol is known to be triboelectrically active. We report how the flow of glycerol, stopped in a cylindrical coiled pipe, influences horseradish peroxidase (HRP) enzyme. Namely, glycerol flow was pumped through the coil and then stopped. After that, we incubated the 0.1 µM solution of HRP near the side of the coil, and then adsorbed HRP onto mica. This operation markedly increased the HRP aggregation on mica in comparison with the control sample. We explain this phenomenon by the influence of triboelectrically induced electromagnetic fields. Our results can be useful in the development of flow-based systems for biosensors and bioreactors.

Safe water is a global public health concern amid increasing scarcity and pollution. Bottled water production and consumption contribute to these problems. This study examines tap water consumption in Italy, assessing associated sociodemographic factors and related health outcomes such as obesity and self-perceived health status. Data from the Italian National Statistics Institute's "Aspects of daily life" survey (N=45,597) were analyzed. Covariates included education, age, gender, economic status, region, concerns about waste and climate change, consumption of carbonated drinks excluding water, alcohol consumption, consumption of vegetables, consumption of snacks, body mass index, and self-perceived health status. Bivariate analyses and mixed-effect logistic regression models explored the associations. People who drink tap water were 19,674 with a higher prevalence in people aged 45 to 59 old, people with a graduate/post-graduate degree diploma, with optimal economic resources, and concerned about waste production and climate change, coming from the North-East regions of Italy. Underweight people showed a higher prevalence of TW assumption as well as those who drink less than occasionally carbonated drinks, drink alcohol, consume vegetables more than once a day, and snacks less than once a week with a satisfying level perceived health status. Regressions showed that all age classes are less likely to drink tap water than people younger than 20 years old. The category with “inadequate” economic resources is more likely to consume tap water. Low educational classes show a low likelihood of consuming tap water as well as Islands. A concern about waste production and climate change is associated with an increased likelihood of assuming tap water. Tap water consumption was negatively associate with obesity but not with a satisfactory Self-perceived health status. Insights from this study can inform public health strategies.

Extracellular vesicles represent a large heterogeneous class of near and long-distance intercellular communication mediators, released by both prokaryotic and eukaryotic cells. Specifically, the scientific community has shown a growing interest in exosomes, which are nano-sized vesicles with an endosomal origin. Not so long ago, the physiological goal of exosome generation was largely unknown and required more investigation; at first, it was hypothesized that exosomes are able to remove excess, rejects and unnecessary constituents from cells to preserve cellular homeostasis. However, thanks to recent studies, the central role of exosomes in regulating cellular dialogue has emerged. Exosomes act as vectors on cell-cell signaling by their cargo, proteins, lipids, and nucleic acids, and influence physiological and pathological processes. The findings on exosomes are widespread in a large spectrum of biomedical applications from diagnosis and prognosis to thera-pies. In this review, we describe exosome biogenesis and the current methods for their isolation and characterization, emphasizing the role of their cargo in female reproductive processes, from gametogenesis to implantation, and the potential involvement in human female disorders.

Brown rice is a familiar whole grain in Japan. We examined national trends in brown rice consumption among Japanese adults aged ≥ 20 years old, using individual-level data from the National Health and Nutrition Surveys conducted between 2012 and 2019. We employed multivariable logistic regression to identify factors associated with brown rice consumption. The 95th percentile of daily brown rice intake remained at 0.0 grams throughout the study period. The percentage of brown rice consumers increased from 1.8% (95% confidence interval: 1.6–2.1) in 2012 to 2.3% (95% confidence interval: 1.8–3.0) in 2019. Compared with individuals who consumed only white rice, brown rice consumers had significantly higher mean intake levels of macronutrients, legumes, vegetables, fruits, and nuts. Brown rice consumption was positively associated with certain sociodemographic characteristics (being female, older age, residing in a major city, living without very young children, and having higher education levels) and health behaviors (lower body mass index, engaging in regular exercise, and being a former or never smoker). Despite its potential nutritional benefits in balanced diets, only a small fraction of adults in Japan consume brown rice, indicating a need for further promotion, particularly among individuals with characteristics associated with brown rice consumption.

The Planetary Roller Screw Mechanisms (PRSMs), alongside Ball Screw Mechanisms (BSMs) and Electromechanical Actuators (EMAs), occupies a pivotal role in advancing the precision and efficiency of various industrial applications, including aerospace, automotive, and high-precision machining tools. Despite their critical advantages such as high load capacity, superior precision, and extended lifespan, the deployment of PRSMs in complex operational conditions reveals a landscape rife with challenges and opportunities for further research. This comprehensive review endeavors to dissect the multifaceted aspects of PRSMs, focusing on their mechanics and dynamics, tribology and thermal behavior, and the paramount importance of reliability and condition monitoring. By synthesizing current research findings, this paper highlights the significant advancements in understanding the static and dynamic characteristics of PRSMs, the intricate interplay between lubrication conditions and wear mechanisms, and the critical role of thermal effects on operational performance. Moreover, it delves into the dynamic models that address the impact of manufacturing imperfections, such as waviness and defects, on the reliability of these mechanisms. Despite the strides made, the review identifies critical gaps in the existing literature, particularly under conditions of extreme temperatures, large deformations, and multifaceted loads, advocating for a holistic approach to research. By proposing integrated thermo-mechanical models and emphasizing the need for empirical validations, this paper outlines a roadmap for future studies aimed at facilitating the development of more robust and reliable PRSMs, capable of meeting the demands of complex operational scenarios and advancing the field of high-precision applications in aerospace, robotics, and beyond.

Benefits of baby swimming have been established, but there is limited knowledge about the methodologies used by practitioners. To address this knowledge gap, this study aimed to categorize and classify the equipment and environmental used in baby swimming programs worldwide. A descriptive categorical content analysis approach was employed to analyse videos of baby swimming programs obtained from YouTube. The framework created was validated for interrater reliability, and a pilot study was conducted to classify videos from different countries based on the equipment and environment used. Results indicated that the physical environments observed were pool tanks and swimming pools with and without depth reduction zones, while the equipment used included assistive devices, toys, and clothes. This study represents a significant first step in the development of a comprehensive tool to systematize and characterize the methodologies used in baby swimming programs globally.

Titanium alloys belong to the metal biomaterials that are one of the most widely used in medicine. In recent years, in order to reduce the use of vanadium, Ti6Al4V alloy is increasingly replaced by Ti6Al7Nb alloy. In addition, to ensure the best possible biocompatibility, its surface is subjected to appropriate modifications, for example, anodic oxidation. Despite the extensive use of anodic oxidation of titanium implants in orthopedics, there are few works focused on a detailed analysis of the chemical composition of the surface layers. In addition, the effect of treatments before anodic oxidation on the properties of the produced layer has not been analyzed. Thus, the purpose of this study was to analyze in detail the chemical composition of the passive layer of Ti6Al7Nb alloy obtained by anodic oxidation preceded by sandblasting. Moreover, the physicochemical properties of the analyzed surface affecting biocompatibility were determined. For this purpose, surface observation, wettability and roughness tests, microhardness tests, electrochemical tests and phase composition analysis were carried out. In addition, the preclinical suitability, of the surface modified in this way, was evaluated by cytotoxicity tests.

Abstract: Short-chain fatty acids (SCFAs) are the major microbial metabolites produced in the gut through the fermentation of non-digestible fibers. SCFAs act through free fatty acid receptor 2 and 3 (FFAR2 and 3), which are known to be expressed on glucagon-like peptide-1 (GLP-1)-secreting L-cells. This pathway is suggested to protect the intestinal mucosa. We aimed to investigate how lack of fiber affects the production of SCFAs and the vulnerability of the co-lon. Additionally, the involvement of FFAR2 and 3 in GLP-1 secretion and intestinal protection. SCFA concentrations in luminal contents from chow- or fiber-free diet-fed mice were analysed by LC‒MS. SCFAs were applied to isolated perfused colons from FFAR2/3 double KO and WT mice, and the secretion of GLP-1 was measured. Dextran sulfate sodium (DSS) colitis was induced in chow- or fiber-free diet-fed mice as well as in FFAR2/3 KO and WT mice. The removal of die-tary fiber significantly decreased total colonic SCFA concentrations, with specific decreases in acetate, propionate, and butyrate. SCFAs significantly increased colonic GLP-1 secretion but not in FFAR2/3 KO mice. In the DSS model, the removal of dietary fiber increased the severity and delayed recovery. Colitis severity was independent of FFAR2 and FFAR3 signaling.

The hump feature is one of the major instabilities in pump-turbines. When pump-turbines operate in the hump region, strong noise and serious fluctuations can be observed, which are harmful to their safe and stable operation and can even destroy the whole unit as well as water conveyance system. In this paper, a low specific speed (n_q = 36.1 min⁻¹) pump-turbine model was experimentally investigated. Firstly, the hump characteristic was obtained under 19 mm guide vane opening conditions. More interestingly, when the hump characteristic was measured in two directions (increasing and decreasing the discharge), characteristic hysteresis was found in the hump region. The analysis of performance characteristics reveals that the hump instability is the result of Euler momentum and hydraulic losses, and different Euler momentum and hydraulic losses in the two development processes lead to the hysteresis phenomenon. Then, 12 pressure sensors were mounted in the different parts of the pump-turbine model to obtain the time and frequency characteristics. The analysis of the corresponding fast Fourier transform confirms that the hump characteristic is related to low-frequency (0.04–0.15 times rotational frequency) vortices. The occurrence and cessation of vortices depend on the operating condition and measurement direction, which contribute to the hysteresis feature. Finally, the type of the low-frequency vortices was analyzed through the cross power spectrum.

Microwave technology has a potential application in the extraction of zinc from sulphide ores, knowledge of the dielectric properties of these ores plays a major role in the microwave design and simulation for any process. The dielectric properties of zinc sulfide concentrate for two different apparent densities—1.54 and 1.63 g/cm³—have been measured by using the resonance cavity perturbation technique at 915 and 2450 MHz during the roasting process for the temperature ranging from room temperature to 850 °C. The variations of dielectric constant, the dielectric loss factor, the dielectric loss tangent and the penetration depth with the temperature, frequency and apparent density have been investigated numerically. The results indicate that the dielectric constant increases as the temperature increases and temperature has a pivotal effect on the dielectric constant, while the dielectric loss factor has a complicated change and all of the temperature, frequency and apparent density have a significant impact to dielectric loss factor. Zinc sulfide concentrate is high loss material from 450 to 800 °C on the basis of theoretical analyses of dielectric loss tangent and penetration depth, its ability of absorbing microwave energy would be enhanced by increasing the apparent density as well. The experimental results also have proved that zinc sulfide concentrate is easy to be heated by microwave energy from 450 to 800 °C. In addition, the experimental date of dielectric constant and loss factor can be fitted perfectly by Boltzmann model and Gauss model, respectively.

Chemical pollution poses a significant threat to human health, with detrimental effects on various physiological systems, including the respiratory, cardiovascular, mental, and perinatal domains. While the impact of pollution on these systems has been extensively studied, the intricate relationship between chemical pollution and immunity remains a critical area of investigation. The focus of this study is to elucidate the relationship between chemical pollution and human immunity. To accomplish this task, this study presents a comprehensive review that encompasses in vitro, ex vivo, and in vivo studies, shedding light on the ways in which chemical pollution can modulate human immunity. Our aim is to unveil the complex mechanisms by which environmental contaminants compromise the delicate balance of the body's defence systems going beyond the well-established associations with defence system delving into the less-explored link between chemical exposure and various immune disorders, adding urgency to our understanding of the underlying mechanisms and their implications for public health.

Cancer is one of the leading causes of death, making timely diagnosis and prognosis very important. Utilization of AI (artificial intelligence) enables providers to organize and process patient data in a way that can lead to better overall outcomes. This review paper aims to look at the varying uses of AI for diagnosis and prognosis and clinical utility. PubMed and EBSCO databases were utilized for finding publications from January 1, 2013, to December 22, 2023. Articles were collected using key search terms such as “artificial intelligence” and “machine learning.” Included in the collection were studies of the application of AI in determining cancer diagnosis and prognosis using multi-omics data, radiomics, pathomics, clinical and laboratory data. The resulting 89 studies were categorized into eight sections based on the type of data utilized and then further subdivided into two subsections focusing on cancer diagnosis and prognosis, respectively. 8 studies integrated more than one form of omics, namely genomics, transcriptomics, epigenomics, and proteomics. Incorporating AI into cancer diagnosis and prognosis alongside omics and clinical data represents a significant advancement. Given the considerable potential of AI in this domain, ongoing prospective studies are essential to enhance algorithm interpretability and to ensure safe clinical integration.

Sterol homeostasis in mammalian cells and tissues involves balancing three fundamental processes: de novo sterol biosynthesis; sterol import (e.g., from blood-borne lipoproteins); and sterol export. In complex tissues, composed of multiple different cell types (such as the retina), import and export also may involve intra-tissue, inter-cellular sterol exchange. Disruption of any of these processes can result in pathologies that impact the normal structure and function of the retina. Here, we provide a brief overview of what is known currently about sterol homeostasis in the vertebrate retina and offer a proposed path for future experimental work to further our understanding of these processes, with relevance to the development of novel therapeutic interventions for human diseases involving defective sterol homeostasis.

The objective of this research was to explore the impact of a gradual replacement of Ca2+ with Mn1+ on the crystal structure of CaHPO4·2H2O, which could be beneficial for producing Ca1−xMnxHPO4·nH2O compounds. In order to prepare the starting solutions required for this study, Ca(NO3) 2·4H2O, (NH4)·2HPO4, and MnNO3·4H2O were used at various molar concentrations. The findings reveal that Mn substitutes Ca partly at low Mn/Ca molar ratios, and Mn doping reduces the unit cell of CaHPO4·2H2O. The produced biphasic compound was composed of monoclinic CaHPO4·2H2O and triclinic/monoclinic nanostructured Mn3PO4O11 after a continuous increase in the Mn/Ca molar ratio to 1. When the Ca/Mn molar ratio is 1.5, a triphasic compound of monoclinic CaHPO4·2H2O, triclinic Mn3P4O11, and Orthorhombic MnHPO4·(H2O)3 phases is formed. The formation of the monophasic MnHPO4·(H2O)3 compound was achieved by increasing the Mn/Ca molar ratio above 4. By adjusting the Mn/Ca molar ratio in the initial solutions, it is possible to produce biomaterials with specific and bespoke characteristics in the future. The Mn/Ca ratio of the starting solution can be modified to produce Ca1-xMnxHPO4-nH2O phases with weight percent compositions, as established. For the first time, Ca1−xMnxHPO4·nH2O compounds were synthesized using novel methods in this manuscript.

Aspalathin (ASP) can protect H9c2 cardiomyocytes against high glucose (HG)-induced shifts in myocardial substrate preference, oxidative stress and apoptosis. While the protective mechanism of aspalathin remains unknown, nuclear factor (erythroid-derived 2)-like 2 (Nrf2) has emerged as a key factor for intracellular responses against oxidative stress. Therefore, we hypothesized that aspalathin protects the myocardium against hyperglycemia-induced oxidative damage by up-regulating Nrf2 expression in H9c2 cardiomyocytes and diabetic (db/db) mice. Using an oxidative stress RT2 Profiler PCR array, ASP at a dose of 1 µM was demonstrated to protect H9c2 cardiomyocytes against HG-induced oxidative stress, but silencing of Nrf2 abolished this protective response of ASP and exacerbated cardiomyocyte apoptosis. Db/db mice and their non-diabetic (db/+) littermate controls were subsequently treated daily for 6 weeks with either a low (13 mg/kg) or high (130 mg/kg) ASP dose. Compared to nondiabetic mice the db/db mice presented increased cardiac remodeling and enlarged left ventricular wall that occurred concomitant to enhanced oxidative stress. Daily treatment of mice with ASP at a dose of 130 mg/kg for 6 weeks was more effective at reversing complications than both a low dose ASP or metformin, eliciting enhanced expression of Nrf2 and its downstream antioxidant genes. These results indicate that ASP maintains cellular homeostasis and protects the myocardium against hyperglycemia-induced stress through activation of Nrf2 and its downstream target genes.

This paper is the second part of a two-part report studying the responses of a typical point-contact elastohydrodynamic lubrication (EHL) problem to multiscale roughness that is mimicked by artificially generated waviness with different amplitudes, frequencies, and directions. The previous Part I paper (doi:10.3390/lubricants10120368) focuses on the full film regime, while the current paper focuses on the partial film regime. The amplitudes and frequencies are related to the feature geometry of smooth EHL problems. Generated waviness is input to a transient thermal EHL model. The simulation is conducted 1,600 times for different waviness parameters, loads, and speeds. Eight performance parameters are extracted: the asperity contact ratio, minimum film thickness, maximum pressure, central point film thickness, central point pressure, mean film thickness, coefficient of friction (COF), and the maximum temperature rise. The ratios of the first seven parameters with and without waviness and the asperity contact ratio values are plotted on the frequency–amplitude coordinate plane as contour maps. The influences of the amplitude, frequency, wave direction, load, and speed on the eight performance parameters are analyzed and summarized. The simulated data and plotted contour maps are provided to the readers in the Supplementary Material.

This article explores the profound implications of Dr. Anthony Fauci's testimony before the U.S. House Select Subcommittee on the Coronavirus Pandemic, where he admitted that key COVID-19 policies lacked scientific backing. By analyzing the foundation of these decisions, the piece delves into the broader issues of scientific evidence, hypothesis validation, and the societal consequences of implementing unverified measures. It raises critical questions about the role of scientific rigor and accountability in policy-making, urging a reflection on our approach to scientific inquiry and decision-making in public health.

Several pathotypes of enteric E. coli have been identified. The group represented by Shiga toxin-producing E. coli (STEC) is of particular interest. Raw milk and raw milk products are significant sources of STEC infection in humans; therefore, identifying pathogens at the herd level is crucial for public health. Most national surveillance programs focus solely on raw milk and raw milk cheeses that are ready for retail sale, neglecting the possibility of evaluating the source of contamination directly at the beginning of the dairy chain. In order to assess the viability of new molecular methodologies applied to raw milk filters enabling the identification of the presence of STEC serotypes in milk production and apply the same methods to identify the presence of these pathogens in calf feces we analyzed, through a commercial real-time PCR assay, a total of 290 samples coming from 18 different dairy herds; 88 bulk tank milk (BTM), 104 raw milk filters (RMF) and 98 calves’ feces samples. In total 3.4% of BTM, 41.4% of RMF and 73.4% of calves’ feces tested positive for stx presence, supporting our hypothesis that BTM is not a suitable matrix to assess the STEC presence at herd level, underestimating it. Our conclusion is that the surveillance program needs critical and extensive improvements such as RMF and calves’ feces analysis implementation in order to be more efficient in detecting and preventing STEC infections. The epidemiology of these infections and the characteristics of the pathogen clearly show how a One Health approach will be pivotal to improve our capabilities to control the spread of these infections.

ACL instability poses a significant challenge in traumatology and orthopedic medicine, often requiring accurate diagnosis for appropriate treatment. While the pivot-shift test offers a crucial means of assessment, its reliance on subjective interpretation underscores the need for supplementary imaging studies. This study aims to address this limitation by developing a Bayesian classification algorithm tailored for integration into a mobile application. Using the built-in inertial sensors of smartphones, this new approach aims to dynamically evaluate rotational stability during knee examinations. Orthopedic specialists conducted knee evaluations on 52 subjects, with subsequent analysis revealing interesting insights. Intraobserver and interobserver analyses, as measured by ICC, demonstrated strong agreement both in terms of timing between maneuvers (ICC = 0.94) and signal amplitude (ICC = 0.71-0.66). Notably, the Bayesian algorithm successfully classified 95% of joint hypermobility cases, with an additional 7 cases of hyperlaxity identified by the Pivot-Shift Meter (PSM). These findings highlight the practicality and effectiveness of implementing a Bayesian classification algorithm within a mobile application for assessing and categorizing signals captured by smartphone inertial sensors during the pivot-shift test.

Aspalathin, a C-glucosyl dihydrochalcone, has previously been shown to protect cardiomyocytes against hyperglycemia-induced shifts in substrate preference and subsequent apoptosis. However, the precise gene regulatory network remains to be elucidated. To unravel the mechanism and provide insight into this supposition, the direct effect of aspalathin in an isolated cell-based system, without the influence of any variables, was tested using an H9c2 cardiomyocytes model. Cardiomyocytes were exposed to high glucose (33 mM) for 48 hours before post-treatment with or without aspalathin. Thereafter, RNA was extracted and RT2 PCR Profiler Arrays were used to profile the expression of 336 genes. Results showed that, 57 genes were differentially regulated in the high glucose or high glucose and aspalathin treated groups. STRING analysis revealed lipid metabolism and molecular transport as the biological processes altered after high glucose treatment, followed by inflammation and apoptosis. Aspalathin was able to modulate key regulators associated with lipid metabolism (Adipoq, Apob, Cd36, Cpt1, Pparγ, Srebf1/2, Scd1 and Vldlr), insulin resistance (Igf1, Akt1, Pde3 and Map2k1), inflammation (Il3, Il6, Jak2, Lepr, Socs3, and Tnf13) and apoptosis (Bcl2 and Chuk). Collectively, our results propose that aspalathin could reverse metabolic abnormalities by activating Adipoq while modulating the expression of Pparγ and Srebf1/2, decreasing inflammation via Il6/Jak2 pathway, which together with an observed increased expression of Bcl2 prevents myocardium apoptosis.

Modern building automation systems implement plenty of advanced control and monitoring functions considering various parameters like users’ activity, lighting, temperature changes etc. Moreover, new solutions based on Internet of Things and cloud services are also being developed for smart buildings to ensure comfort of use, user safety, energy efficiency improvements and integration with smart grids and smart city platforms. Such a wide spectrum of technologies and functions requires a new approach in building automation systems design to provide effective way of their implementation and flexibility during operation. At the same time, in the building design and operation industries, tools based on building information modeling and digital twins are being developed. In this paper, the authors discuss development directions and application areas of these solutions, identifying new trends and possibilities of their use in smart homes and buildings. In particular, the focus is on procedures for selecting automation functions, effective integration, and interoperability of building management systems with Internet of Things considering organization of prediction mechanisms and dynamic functional changes in buildings and smart networks. Chosen solutions and functions should consider the requirements from EN ISO 52120 standard and the guidelines defined for the Smart Readiness Indicator.

Delivering nucleic acid therapeutics across cell membranes is a significant challenge. Cell-penetrating peptides (CPPs) containing arginine (R), tryptophan (W), and histidine (H) show promise for siRNA delivery. To improve siRNA delivery and silencing a model STAT3 gene, we hypothesized that oleyl acylation to CPPs, specifically (WRH)n, would enhance STAT3 silencing efficiency in breast and ovarian cancer cells. Using Fmoc/tBu solid-phase peptide chemistry, we synthesized, purified, and characterized the oleyl-conjugated (WRH)n (n = 1-4) peptides. The peptide:siRNA complexes were non-cytotoxic at N/P 40 (~20 μM) against MDA-MB-231, MCF-7, SK-OV-3, and HEK-293 cells after 72 h incubation. All peptide:siRNA complexes showed serum stability at N/P ≥40. The synthesized conjugates, with a diameter of &lt;100 nm, formed nano complexes with siRNA and exhibited stable range of zeta potential values (13-18 mV at N/P 40). Confocal microscopy and flow cytometry analysis provided qualitative and quantitative evidence of successful cellular internalization of siRNA. Peptides oleyl-(WRH)3 and oleyl-(WRH)4 showed ~60% and ~75% cellular uptake of siRNA, respectively, in both MDA-MB-231 and SK-OV-3 cells. Western blot analysis of oleyl-(WRH)4 demonstrated effective silencing of the STAT-3 gene, with ~75% silencing in MDA-MB-231 cells and ~45% in SK-OV-3 cells.

Surgical simulators are crucial in early craniofacial and plastic surgical training, necessitating synthetic materials that accurately replicate tissue properties. Recent critiques of our lab’s currently deployed silicone surrogate have highlighted numerous areas for improvement. To further refine our models, our group's objective is to find a composition of materials that is closest in fidelity to native oral mucosa during surgical rehearsal by expert craniofacial surgeons. Fifteen platinum silicone-based surrogate samples were constructed with variable hardness and slacker percentages. These samples underwent evaluation of tactile sensation, hardness, needle puncture, cut resistance, suture retention, defect repair, and tensile elasticity. Expert craniofacial surgeon evaluators provided focused qualitative feedback on selected top-performing samples for further assessment and statistical comparisons. Evaluation revealed surrogate characteristics with satisfactory to good performance. Sample 977 exhibited the highest performance, and comparison with the original surrogate (sample 810) demonstrated significant improvements in critical areas, emphasizing the efficacy of the refined composition. The study identified a silicone composition that directly addresses the feedback received by our team’s original silicone surrogate. The study underscores the delicate balance between biofidelity and practicality in surgical simulation. The need for ongoing refinement in surrogate materials is evident to optimize training experiences for early surgical learners.

Surgical simulators are crucial in early craniofacial and plastic surgical training, necessitating synthetic materials that accurately replicate tissue properties. Recent critiques of our lab’s currently deployed silicone surrogate have highlighted numerous areas for improvement. To further refine our models, our group's objective is to find a composition of materials that is closest in fidelity to native oral mucosa during surgical rehearsal by expert craniofacial surgeons. Fifteen platinum silicone-based surrogate samples were constructed with variable hardness and slacker percentages. These samples underwent evaluation of tactile sensation, hardness, needle puncture, cut resistance, suture retention, defect repair, and tensile elasticity. Expert craniofacial surgeon evaluators provided focused qualitative feedback on selected top-performing samples for further assessment and statistical comparisons. Evaluation revealed surrogate characteristics with satisfactory to good performance. Sample 977 exhibited the highest performance, and comparison with the original surrogate (sample 810) demonstrated significant improvements in critical areas, emphasizing the efficacy of the refined composition. The study identified a silicone composition that directly addresses the feedback received by our team’s original silicone surrogate. The study underscores the delicate balance between biofidelity and practicality in surgical simulation. The need for ongoing refinement in surrogate materials is evident to optimize training experiences for early surgical learners.

Background/Objectives: PEMF therapy has gained significant attention due to its potential benefits in promoting tissue repair and improving overall well-being. Recent publications in the field of exercise physiology, showed that pulsed electromagnetic fields (PEMFs) enhanced the velocity and the quantity of muscle O2 available and the rate of muscle oxygen extraction and utilization, in semi-professional cyclists, during a heavy constant-load exercise. In this paper, we investigate the effect of stimulation on muscular activation, in sedentary young people, during a constant-load exercise, performed at moderate intensity. Methods: Nine male sedentary young people, partic-ipated in this study. The response of the muscle activity, was recorded by surface EMG and assessed measuring the root mean square (RMS) normalized to the peak of the maximum voluntary con-traction. Data were collected in the right vastus Medialis (RVM) and right Biceps Femoris (RBF) at the baseline (standstill sitting), on warm-up (unloaded cycling) and during 30 minutes of con-stant-load exercise, in two experimental conditions (PEMF ON vs PEMF OFF). Results: The mul-tivariate analysis of variance performed on RVM showed a significant effect of PEMF in both warmup and exercise, while on RBF showed a significant effect of PEMF and warmup. Conclusions: PEMF strongly enhanced the amplitude of muscle activity in young sedentary people. The increase in the amplitude of the muscular response may lead to a higher oxygen consumption and release.

Previous high throughput screening studies indicated trans-eQTLs tend to be tissue specific. In this study, I probed if this feature can be used to identify tissue-specific gene regulatory networks. eQTL data (P<5e-8) for 16,259 genes were identified and their summary association statistics were obtained from the eQTLGene database. Next, eQTLs that display both cis and trans regulatory effects were selected and the association between their corresponding genes were examined using Mendelian randomization. A total of 169 genes that exerted trans-regulatory impacts on 692 genes were identified. 90% of the genes (N=749) aggregated into a gene regulatory network significantly enriched in hemo-immune processes. The robustness of finding was confirmed through simulation. The identified network displayed the scale-free topology. This provided the reason to examine the association of the network’s hub genes with the phenome. The outcome of analyses revealed GSDMB and ORMDL3 impact several disorders of immune origin and ALDH2 overexpression contributes to obesity. This study reports trans-eQTLs can be used to identify tissue-specific gene regulatory networks and describes a workflow to achieve this purpose. The network identified in this study showed scale-free topology indicating the hub genes of a GRN could be targeted to prevent disease outcomes.

The terpolymers of N-vinylpyrrolidone (VP) with acrylic acid and triethylene glycol methacrylate were synthesized with more than 90% yield by radical copolymerization in ethanol from monomeric mixtures of different composition (98 : 2 : 2, 95 : 5: 2 and 98 : 2: 5). Their physical and chemical characteristics such as monomer composition, absolute molecular masses and hy-drodynamic radii in aqueous media at different temperature were determined. The temperature effect on the behavior of terpolymers in water and aqueous saline buffer solution with pH 7.4 has been studied and the ability of a copolymer enriched with dimethacrylates units was discovered to respond to a temperature change in these media. On the basis of terpolymers and linear polyvi-nylpyrrolidone (PVP), polymer compositions of hydrophobic dye methyl pheophorbide a, MPP, that is fluorescent in the red region of the spectrum, were obtained; the sizes of the polymer nanostructures of MPP in water were determined. The structures based on terpolymers were demonstrated to be more stable than MPP-PVP ones. It was carried out the quantum-chemical modelling of the possible structures of MPP-copolymer that formed as a result of intermolecular interaction between MPP and terpolymer’s chains; the possibility of the formation of hydrogen bonds between the donors of the electrons of terpolymer units and the proton donors of the MPP molecule was shown. Using the MTT test, it was established that copolymers of various compositions are low toxic for non-tumor Vero cells and HeLa tumor cells. It was shown that the cytotoxicity of polymer particles loaded with MPP for FetMSC and HeLa cells increased. Using fluorescence microscopy, the accumulation and distribution of polymer particles in non-tumor (FetMSC) and tumor (HeLa) cells was studied and an increase in the accumulation of MPP with both types of particles was shown.

Previous reviews have investigated machine learning (ML) models used to predict the risk of developing preeclampsia but have not described how the ML models are intended to be deployed throughout pregnancy or feature performance. The aim of this study is to provide an overview of the existing ML models and their intended deployment patterns and performance along with identified features of high importance. This review used the Preferred Reporting Items for Systematic Reviews and Meta-Analyses 2020 guidelines. PubMed, Engineering Village, and the Association for Computing Machinery were searched between January and February 2024. A total of 86 studies were found of which 14 were included. Out of 12 studies, eight showed the intent to use the ML model as a single-use, two intended a dual-use, and two intended multiple-use. A total of seven studies listed the features of the highest importance. Systolic and diastolic blood pressure were listed along with mean arterial pressure to be of high importance. Out of four studies intending to use the ML model more than a single-use, three of them were conducted in the years 2023 and 2024, whereas the remaining study is from 2011. No ML model emerged as superior across the subgroups of PE. Utilizing body mass index and either mean arterial pressure or diastolic blood pressure and systolic blood pressure may benefit the performance. The deployment patterns are mainly single use being within the gestation weeks 11+0 to 14+1.

Respiratory Syncytial Virus (RSV) continues to pose a significant challenge, contributing to elevated hospitalization rates among children up to 5 years old, with a disproportionate burden on newborn and infants under 6 months old. The unique characteristics of the young immune system make it prone to altered responses to infections and vaccinations, requiring a tailored approach to disease prevention. The recent approval of the maternal RSV vaccine, (brand name ABRYSVO), represents a pivotal advancement in preventive strategies among newborns and infants, marking a milestone in RSV research as the first market-approved maternal vaccine. The present review examines clinical trial data on both recent and previous vaccine candidates, as well as the licensed vaccine, focusing on the prevention of RSV disease in newborns and young infants through the passive acquisition of antibodies following maternal immunization. Additionally, it evaluates the safety profile of these vaccines.

Complexity science studies physical phenomena that cannot be explained by the mere analysis of the single units of a system but requires to account for their interactions. A feature of complexity in connected systems is the emergence of mesoscale patterns in a geometric space, such as groupings in bird flocks. These patterns are formed by groups of points that tend to separate from each other, creating mesoscale structures. When multidimensional data or complex networks are embedded in a geometric space, some mesoscale patterns can appear respectively as clusters or communities, and their geometric separability is a feature according to which the performance of an algorithm for network embedding can be evaluated. Here, we introduce a framework for the definition and measure of the geometric separability (linear and nonlinear) of mesoscale patterns by solving the travelling salesman problem (TSP), and we offer experimental evidence on embedding and visualization of multidimensional data or complex networks, which are generated artificially or are derived from real complex systems. For the first time in literature the TSP’s solution is used to define a criterion of nonlinear separability of points in a geometric space, hence redefining the separability problem in terms of the travelling salesman problem is an innovation which impacts both computer science and complexity theory.

This study compared the efficacy of alfaxalone and propofol to induce anesthesia in bitches undergoing an ovariohysterectomy or cesarean sections. 34 healthy and pyometra-affected females were induced with IV propofol administration, 35 healthy and pyometra-affected bitches were induced with the IV administration of alfaxalone. For the cesarean sections, females were induced with propofol (n=14) or alfaxalone (n=14). Maternal physiological parameters (heart rate, blood pressure, temperature) were recorded throughout surgeries; the viability and a modified Apgar score was recorded in the neonates at 5, 60 and 120 minutes after delivery. The use of propofol and alfaxalone did not show relevant differences over parameters assessed, when ovariohysterectomy was performed in healthy bitches or females with pyometra, as well as when cesarean sections were compared; only, a transient tachycardia appeared after alfaxalone administration. However, a higher percentage of bitches needed extra-doses of propofol. Neonatal mortality was similar between both groups, but when alfaxalone was used a higher neonatal viability was observed. Propofol and alfaxalone showed similar efficacy to perform the ovariohysterectomy in all bitches. Both protocols were optimal for cesarean sections, but alfaxalone was associated with a higher neonatal viability and a higher neonatal survival rate.

This study proposes an innovative pharmacovigilance approach, VIGI-4, leveraging ChatGPT Teams Pro version. Our method involves aggregating data from all phase 4 studies published in February 2024 to identify adverse reactions. These results are categorized by disease state alphabetically, demonstrating the method's capacity to generate structured and easily navigable outputs. The results section is tailored to exemplify the valuable, actionable insights attainable through our workflow. This research emphasizes the game-changing potential of integrating advanced technologies such as ChatGPT into pharmacovigilance, signaling a new era in safeguarding drug safety.

Introduction: Subtalar Arthroereisis (STA) is a surgical intervention for pediatric flexible flatfoot (PFF), primarily targeting hindfoot alignment by limiting excessive subtalar eversion. However, its effects on forefoot parameters remain underexplored. This study aims to investigate radiological changes following STA in pediatric patients. Materials and Methods: A retrospective analysis was conducted on consecutive patients treated with STA for PFF. First ray-related angles, including Hallux Valgus Angle (HVA) and Inter-Metatarsal Angle (IMA), alongside hindfoot radiological parameters such as Meary, Calcaneal Pitch, and Costa Bartani angles, were assessed. Subgroup analysis by gender was performed, and correlations between demographic and pre-operative radiological parameters were examined. Results: Forty-one patients (81 feet) with a mean age of 11.6 years were included, with a mean follow-up duration of 6.4 months. No significant differences were observed in first ray-related an-gles pre- and post-operatively, with mean IMA changing from 7.97° to 7.18° and mean HV angles from 9.51° to 8.66°. Noteworthy improvements were seen in flat foot angles, including Meary, Calcaneal Pitch, and Costa Bartani angles, postoperatively. Age subgroup analysis revealed similar trends in IMA and HVA changes between Group A (operated before peak growth) and Group B (operated later). Higher preoperative angles tended to improve, while lower preoperative IMA and HVA tended to worsen postoperatively, all remaining within normal ranges. Conclusion: STA showed positive radiological outcomes for PFF treatment, while negligible changes in first ray-related angles were observed. Age subgroup analysis indicated similar trends regardless of operation timing. Higher preoperative angles tended to improve, while lower preoperative angles tended to worsen postoperatively, despite all falling within non-pathological ranges. Further re-search is warranted to confirm this correlation.

Recent research has highlighted associations between sleep and microbial taxa and pathways. However, the causal effect of these associations remains unknown. To investigate this, we performed a two-sample bidirectional Mendelian randomization (MR) analysis using summary statistics of genome-wide association studies (GWAS) from 412 gut microbiome traits (N = 7,738) and GWAS studies from seven sleep-associated traits (N = 345,552 to 386577). We employed multiple MR methods to assess causality, with Inverse Variance Weighted (IVW) as the primary method. We further applied Cochran’s Q statistical analysis, MR-Egger intercept, and MR-PRESSO for heterogeneity and pleiotropy assessment, alongside a Bonferroni correction ((P

This study aimed to investigate the potential of Cord Blood Stem Cell-derived exosome vesicles (CBSC-EVs) in regulating cancer growth and preventing cellular damage. The study aimed to examine the effects of CBSC-EVs on CHL1 cancer cells and healthy fibroblasts. The study results reveal that CBSC-EVs have an anti-cancer/antioxidant effect on CHL1 cancer cells without inducing any toxic effects on healthy lymphocytes. Further analysis of CBSC-EVs revealed the presence of seven miRNAs (noncoding RNA molecules), including three from the Let 7 family, two from the Let 5 family, and two novel miRNAs. The function of the novel miRNAs was the main focus of the study. To assess the efficacy of CBSC-EVs, CHL1 cells (a type of malignant melanoma cell line) and human fibroblasts were grouped into different treatments. One group of those cell lines were treated with CBSC-EVs, and in the second group, the cells were transfected with either miRNA inhibitor Novel 1 (miRNA IN1) plus CBSC-EVs or miRNA inhibitor Novel 2 (miRNA IN2) and CBSC-EVs to knock down those novel miRNAs in the CBSC-EVs. Therefore, by comparing these groups, the function of novel miRNAs is more understandable. In this study, the Comet assay was employed to evaluate cancer cells' DNA damage and CCK8 to measure cell viability. The findings revealed that CBSC-EVs caused an increase in DNA damage in CHL1 cells compared to cells without treatment (p

Proteases represent common targets in combating infectious diseases including COVID-19. The 3-chymotrypsin-like protease (3CLpro) is a validated molecular target for COVID-19 and it is key for developing potent and selective inhibitors for inhibiting viral replication of SARS-CoV-2. In this review, we discuss structural relationships and diverse subsites of 3CLpro, shedding light on the pivotal role of dimerization and active site architecture in substrate recognition and catalysis. Our analysis of bioinformatics and other published studies unveil a proposal of a novel catalytic mechanism for the SARS-CoV-2 polyprotein cleavage by 3CLpro, centering on the triad mechanism involving His41-Cys145-Asp187 and its indispensable role in viral replication. Recognizing Asp187 as a crucial component in the catalytic process underscores its significance as a fundamental pharmacophoric element in drug design. Next, we provide an overview of both covalent and non-covalent inhibitors, elucidating advancements in drug development observed in preclinical and clinical trials. By highlighting various chemical classes and their pharmacokinetic profiles, our review aims to guide future research directions toward the development of highly selective inhibitors, underscore the significance of 3CLpro as a validated therapeutic target, and propel the progression of drug candidates through preclinical and clinical phases.

Fungal infections (FIs) are spreading globally causing a significant public health concern. However, its documentation remains sparse in Africa, particularly in Rwanda. This literature review, aims to assess the risk and document current gaps in evidence and policy. It summarizes the published data about FIs in Rwanda, including ten reports published between 1972-and-2022. Blastomyces, Candida, Cryptococcus, Histoplasma, Microsporum, Pneumocystis, Rhinosporidium, and Trichophyton caused human infections. These infections primarily affected the brain, respiratory, urinary and reproductive organs, and they were diagnosed using culturing, histopathology, immunology, and/or microscopic techniques. Our findings provide an overview of the diversity and distribution of FIs, highlighting significant limitations in the country’s diagnostic capacity and surveillance system for FIs. Also, indicating severe gaps in evidence to inform policymaking, guide strategic planning and intervention, underscoring the urgent need to build national capacity in fungal diagnosis, surveillance, and research. Raising awareness among the public, scientific community, healthcare providers, and policymakers remains crucial. Furthermore, this report reveals the threats of FIs on public health and food insecurity in Rwanda. A Multisectoral One Health Strategy is essential in research and intervention to determine and reduce the health and safety impacts of fungal pathogens on human, animal, and the environment.

Maritime data not only identify financial resources that can significantly enhance the efficiency of shipping companies but also play a pivotal role in promoting eco-friendly and sustainable shipping practices. However, active corporate strategies are required to include maritime data essential for the commercial operation of autonomous ships in the form of corporate assets by transparent evaluating the data. The aim of this study is to review previous studies on da-ta-valuation models, identify a valuation model suitable for maritime business, consider the characteristics of maritime data. The analytic hierarchy process (AHP) method is used to derive priorities for valuing maritime data assets, with emphasis placed on the characteristics of mari-time data, followed by the character of the future-oriented maritime-data market and the da-ta-valuation model. The results obtained that the most important factors in selecting a maritime data-valuation model by analyzing the AHP method were identified as the characteristics of the maritime data(M1). The next most important factors analyzed were the features of the mari-time-data market(M2) and the features of the maritime data-valuation model(M3) in order. In addition, the characteristics of maritime data were preferentially considered among the main criteria, and the market approach (A2) was selected as the most optimal valuation model. The potential impact of this implementation could contribute to the establishment of an intelligent technology market by estimating the value of data and developing a platform for maritime data trading, allowing for more efficient data sharing and utilization by maritime autonomous sur-face ship(MASS).

Bosentan, an endothelin-receptor antagonist (ERA), has potential anti-atherosclerotic properties. We investigated the complementary effects of bosentan and atorvastatin on the progression and composition of the atherosclerotic lesions in diabetic mice. Forty-eight male apoE-/- mice were fed high-fat diet (HFD) for 14 weeks. At week 8, diabetes was induced with streptozotocin and mice were randomized into 4 groups: 1) Control/COG: no intervention. 2) ΒΟG: bosentan 100 mg/kg/day per os. 3) ATG: atorvastatin 20mg/kg/day per os). 4) BO+ATG: Combined administration of bosentan and atorvastatin. The intra-plaque contents of collagen, elastin, monocyte chemoattractant protein-1 (MCP-1), tumor necrosis factor-a (TNF-a), matrix-metalloproteinases (MMP-2,-3,-9), and TIMP-1 concentrations were determined. The percentage of lumen stenosis significantly decreased across all treated groups: BOG: 19.5±2.2%, ATG: 12.8±4.8%, BO+ATG: 9.1±2.7% compared to controls (24.6±4.8%, p&lt;0.001). Both atorvastatin and bosentan significantly increased collagen content and fibrous cap thickness versus COG (p&lt;0.01). All intervention groups reduced the relative intra-plaque concentrations of MCP-1, MMP-3,-9, and increased TIMP-1 compared to COG (p&lt;0.001). Importantly, bosentan showed modest but additive to atorvastatin effects on the latter parameters compared COG (p&lt;0.05). Bosentan treatment in diabetic, atherosclerotic apoE-/- mice delayed the atherosclerosis progression and enhanced plaques’ stability, showing modest but complementary effects with atorvastatin, which are promising in atherosclerotic cardiovascular diseases.

The morphological and compositional complexities of keratinized components make feathers ingenious skin appendages adapted to diverse ecological needs. Frizzling feathers, characterized by their distinct curling phenotypes, offer a unique model to explore the intricate morphogenesis in developing a keratin-based bioarchitecture over a wide range of morphospace. Here, we investigated the heterogeneous allocation of α- and β-keratins in flight feather shafts of homozygous and heterozygous frizzle chickens by analyzing the medulla-cortex integrations using quantitative morphology characterizations across scales. Our results reveal intriguing construction of frizzling feather shaft through modified medulla development, leading to a perturbed balance of the internal biomechanics and, therefore, introducing the inherent natural frizzling compared to those from wild-type chickens. We elucidate how the localized developmental suppression of the α-keratin in the medulla interferes with the growth of the hierarchical keratin organization by changing the internal stress in the frizzling feather shaft. This research not only offers insights into the morphogenetic origin of the inherent bending of frizzling feathers but also facilitates our in-depth understanding of the developmental strategies toward the diverse integuments adapted for ecological needs.

The period of the COVID-19 pandemic resulted in a rapid development of innovative education methods, in particular using e-learning and remote work tools. The effects of this development are also post-pandemic changes in formal teaching regulations, in particular in higher education, allowing classes and lectures to be carried out with Blended Learning or Flipped Classroom methods. This paper provides information about a case study of implementing ICT technologies with elements of the mentioned methods in one of the subjects at a technical university. The implemented tools and solutions in the field of e-learning and interactivity are presented, along with information regarding their perception by students during two academic years in the post-COVID-19 period. The analysis of results of these information and student evaluations indicates their generally positive approach to such innovations in the educational path, and at the same time shows significant challenges for teachers to increase the attractiveness and effectiveness of the teaching process and the development of practical, technical skills of students.

Melatonin is a ubiquitous molecule found in living organisms, ranging from bacteria to plants and mammals. It possesses various properties, partly due to its robust antioxidant nature and partly owed to its specific interaction with melatonin receptors present in almost all tissues. Melatonin regulates different physiological functions and contributes to the homeostasis of the entire organism. In the human eye, a small amount of melatonin is also present, produced by cells in the anterior segment and the posterior pole, including the retina. In the eye, melatonin may provide antioxidant protection along with regulating physiological functions of ocular tissues, including intraocular pressure (IOP). Therefore, it is conceivable that the exogenous administration of sufficiently high amounts of melatonin to the eye could be beneficial in several instances: for the treatment of eye pathologies like glaucoma, due to the IOP-lowering and neuroprotection effects of melatonin; for the prevention of other dysfunctions, such as dry eye and refractive defects (cataract and myopia) mainly due to its antioxidant properties; for diabetic retinopathy due to its metabolic influence and neuroprotective effects; for macular degeneration due to the antioxidant and neuroprotective properties; and for uveitis, mostly owing to anti-inflammatory and immunomodulatory properties. This paper reviews the scientific evidence supporting the use of melatonin in different ocular districts and provides data suggesting that the topical administration of melatonin as eye drops is a real possibility. This way, its distribution and concentration in different ocular tissues may support its pleiotropic therapeutic effects.

in the context of advanced nanomaterials research, nanogels have recently gained considerable attention for their versatility and promising biomedical applications. To date, a significant number of nanogels have been developed to meet the growing demands in various fields of biomedical research. Summarising preparation methods, physicochemical and biological properties and recent applications of nanogels may be useful to help exploring new directions for their development. This article presents a comprehensive overview of the latest nanogel synthesis methodologies, highlighting advances in formulation with different types of hydrophilic or amphiphilic polymers. It also underlines recent biomedical applications of nanogels in drug delivery and imaging, with a short section dedicated to biosafety considerations of these innovative nanomaterials. In conclusion, this article summarises recent innovations in nanogel synthesis and their numerous applications, highlighting their considerable potential in the biomedical field.

Bio-molecular reagents like antibodies required in experimental biology are expensive and their effectiveness, among other things, is critical to the success of the experiment. Although such resources are sometimes donated by one investigator to another through personal communication between the two, there is no previous study to our knowledge on the extent of such donations, nor a central platform that directs resource seekers to donors. In this paper, we describe, to our knowledge, a first attempt at building a web-portal titled Bio-Resource Exchange that attempts to bridge this gap between resource seekers and donors in the domain of experimental biology. Users on this portal can request for or donate antibodies, cell-lines and DNA Constructs. This resource could also serve as a crowd-sourced database of resources for experimental biology. Further, in order to index donations outside of our portal, we mined scientific articles to find instances of donations of antibodies and attempted to extract information about these donations at the finest granularity. Specifically, we extracted the name of the donor, his/her affiliation and the name of the antibody for every donation by parsing the acknowledgements sections of articles. To extract annotations at this level, we propose two approaches – a rule based algorithm and a bootstrapped relation learning algorithm. The algorithms extracted donor names, affiliations and antibody names with average accuracies of 57% and 62% respectively. We also created a dataset of 50 expert-annotated acknowledgements sections that will serve as a gold standard dataset to evaluate extraction algorithms in the future. Contact: [email protected], [email protected] Database URL: http://tonks.dbmi.pitt.edu/brx Supplementary information: Supplementary data are available at Database online.

Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) is a positive sense single stranded RNA genome containing virus which has infected millions of people all over the world particularly China. The virus has been mutating rapidly enough resulting in the emergence of new variants and sub-variants which have reportedly been spread from Wuhan city of China, the epicenter of the virus, to the rest of China and all over the world. The occurrence of mutations in the viral genome especially in the viral spike protein region has resulted in the evolution of multiple variants and sub-variants which gives the virus benefit of host immune evasion and render the modern-day vaccines and therapeutics ineffective. Therefore, there is a continuous need to study the genetic characteristics and evolutionary dynamics of the SARS-CoV-2 variants. Hence, in this study, a total of 833 complete genomes of SARS-CoV-2 variants (including the wild-type or reference sequence) from Taiyuan and Wuhan cities of China were genetically characterized and studies their phylogenetic and evolutionary dynamics using phylogenetics, genetic similarity, and phylogenetic network analysis. Our results show a lot of useful information regarding the evolutionary dynamics of the viral variants, their genetic similarities/dissimilarities, and their phylogenetic relationships. It has been reported in this study that the SARS-CoV-2 variants have nine recombinant events which suggest very important information regarding the viral evolution. In addition, the phylogenetic network analysis shows the number of mutations resulting in emergence and clustering of the viral variants of both cities which reveal significant information regarding the phylodynamics of the virus. This study, to the best of our knowledge, is the first ever genetic comparative study of Taiyuan and Wuhan cities. This study will help better understand the virus, cope with the emergence, and spread of new variants at local level as well as at international level and inform the public health authorities to make better informed decisions in designing new viral vaccines and therapeutics.

Identifying punch types as part of punch kinematic analysis is a key component for both coaches and players, providing critical insights into the variety and effectiveness of punches, which are essential for refining overall performance. Existing research indicates that punch type classification typically relies on data from either wearables or video data. Both approaches have their merits and demerits but require a significant amount of labeled data for modeling the classification algorithm. In this work, we propose a novel approach that significantly reduces the labeling effort by one-sixth by leveraging video data to enhance the training information of sensor data. This enriched training phase enables more accurate punch classification with reduced labeled data. Subsequently, the real-time punch identification and classification use only the wearable data. On a real dataset, with 15% of the labeling efforts, our approach achieved an accuracy rate of 91.41% for rear hand punch recognition and 91.91% for lead hand punch recognition, along with 92.33% and 94.56% for punch classification, respectively. Through the development of our Smart Boxer system, we aim to revolutionize punch analytics in boxing, providing comprehensive insights while enhancing the overall training and competitive experience for athletes and enriching fan engagement with the sport.

There is increasing evidence that some adult mitral valve pathologies may have developmental origins involving errors in cell signaling and protein deposition during valvulogenesis. While early and late gestational stages are well-documented in zebrafish and small mammalian models, longitudinal studies in large mammals with a similar gestational period to humans are lacking. Further, the mechanism of chordae tendineae formation and multiplication remains unclear. This current study presents a comprehensive examination of mitral anterior leaflet and chordae tendineae development in a bovine model (with a gestational period of 9 months). Remarkably distinct from small mammals, bovine development displayed early branched chordae, with increasing attachments only until birth, while the anterior leaflet grew both during gestation and postnatally. Chordae also exhibited accelerated collagen deposition, maturation, and crimp development during gestation. These findings suggest that the bovine anterior leaflet and chordae tendineae possess unique compartmentalized processes of development despite being a continuous collagenous structure.

At present, the health systems of many countries face complex challenges even if their priority objectives remain the same - to provide sustainable health systems at the current and the prognostic demographic changes and requirements in a health system. The quality and the efficiency of healthcare delivery and their mutual conformity have been brought to public attention. Similarly, the quality and the efficiency of an entire process depends on the instrumentation and its procurement that represents a significant economic and procedural issue in the healthcare systems for a long time. Many reports of the public procurement processes and research studies declare this fact. The primary aim of this study is to evaluate the public procurement efficiency in the health system by means of the valuation approach, or savings’ estimates that are achieved by the public procurement. The savings were defined as a percentage difference between the estimated and the final contract price. The secondary objective is to examine an influence of selected variables on a creation of savings in the public procurement process by means of a regression analysis. The researched variables are as follows: time, method, procurement, NUTS level of procurement, Common Procurement Vocabulary Code, number of offers. The analysis results showed interesting findings. The number of offers has a significantly positive impact on the savings. It means that if the number of offers increases by one unit, the savings will increase by 15.6%. Also, time variable (year) has a positive impact on the savings. Consequently, it may be assumed that the public procurement process is improving from a time perspective. It may be partially caused by the fact that a new public procurement legislative has been valid since 2015. The NUTS level has also an impact on the savings in relation to the public procurement. The public procurements which took place at the level of a state were more beneficial as the public procurements at the regional level. Also, the procurement method was statistically significant parameter of a regression analysis. The competition actions together with a negotiation process created higher savings in comparison to tenders. In case of the CPV codes, the most significant savings were achieved in the group of ‘various medicinal products’. The study’s results provide a valuable knowledge for the creators of policies and a realization of the national strategic plans within the health system. Also, these results support a creation of national and international benchmarks in this area and a networking of international partnerships in the area of a public procurement that focus on a development of methodologies and comparative platforms creation.

(1) Background: In this work, a series of benzimidazole derivatives containing colchicine-like and cathechol-like moieties with methyl group substitution in the benzimidazole ring were evaluated for their in vitro antiproliferative, pro-apoptotic and antioxidative activity against highly invasive breast cancer cell line MDA-MB-231 and related impairment of tubulin dynamics; (2) Methods: MTT assay was used to evaluate the antiproliferative activity. In vitro tubulin polymerization assay as well as docking analysis was applied to prove the alterations in tubulin polymerization. Immunofluorescent and DAPI staining reveal the pro-apoptotic potential of benzimidazole derivatives and the effect on tubulin’s dynamics in living cells. The antioxidant activity was evaluated by scavenging of H2O2 and hypochlorite ion and ortho-phenanthroline tests; (3) Results: The compounds containing colchicine-like moiety displayed significant growth inhibitory effect against cancer cell line as was highlighted the role of methyl functional group on the tubulin aggregation and blockage of mitosis. All compounds showed an ability to scavenge H2O2, while the compounds with cathecol-like moiety were more effective against hypochlorite ion and chelation of iron; (4) Conclusions: The benzimidazole derivative containing colchicine-like moiety and methyl group substitution in benzimidazole ring is a potential antiproliferative and microtubule destabilizing agent.

Honey is a sweet substance extensively consumed in the world for its nutritional and healthy properties. However, residues of pesticides and environmental contaminants can compromise its quality. For this reason, the physicochemical parameters, and the organic contamination of monofloral and multifloral honeys from three regions of Algeria (Tiaret, Laghouat and Tindouf) were monitored to evaluate the quality of honey and the safety for consumers. In general, the results obtained from the physicochemical analyses were in line with the EU standards. In terms of contamination, pesticides authorised and used in Algerian agriculture (matalaxyl-M and cyromazine), as well as banned pesticide (carbaryl), were found in almost all the samples. However, only the concentration of cyromazine was higher than the relative EU maximum residue levels. PCB 180, PCB 189, anthracene, fluorene and phenanthrene were mainly detected. All the honeys show traces of DiBP, DBP, DEHP and DEHT, but no traces of bisphenols were found. Moreover, the dietary exposure assessment shows that a small amount of Algerian honey can be safely consumed. Overall, data from this study should motivate the Algerian government to enhance their monitoring activities in beekeeping and to find solutions for implementing more sustainable agricultural practices harmonizing with the international legislation.

Even though inhalation dosimetry is determined by three factors (i.e., breathing, aerosols, and the respiratory tract), the first two categories have been more widely studied than the last. Both breathing and aerosols are quantitative variables that can be easily changed, while respiratory airway morphologies are difficult to reconstruct, modify, and quantify. Despite several methods are available for model reconstruction and modification, developing an anatomically accurate airway model and morphing it to various physiological conditions remains labor-intensive and technically challenging. The objective of this study is to explore the feasibility of using an adjoint-CFD model to understand airway shape effects on vapor deposition and control vapor flux into the lung. A mouth-throat model was used, with the shape of the mouth and tongue being automatically varied via adjoint morphing, and the vapor transport being simulated using ANSYS Fluent coupled with a wall absorption model. Two chemicals with varying adsorption rates, Acetaldehyde and Benzene, were considered, which exhibited large differences in dosimetry sensitivity to airway shapes. For both chemicals, large shape deformations were explored to find the maximal possible morphing; both the maximal and intermediate deformations were simulated for morphology parametric studies. Results show that changing the mouth-tongue shape can alter the oral filtration by 3.2% for Acetaldehyde and 0.27% for Benzene under a given inhalation condition. This study demonstrates that the hybrid adjoint-CFD approach can be a practical and efficient method to investigate morphology-associated variability in inhalation dosimetry of vapors and nanomedicines.

Personal protective equipment (P PE) rules must be respected and followed to the letter of healthcare professionals in Cameroon to avoid the transmission of infectious diseases. This research proposes solutions to the problems of non-adherence and non-compliance among healthcare workers in Cameroon towards PPE rules. Inadequate access to suitable PPE, discomfort when wearing PPE during poor quality, and a lack of training on correct PPE use are just a few of these obstacles amongst HCWs in Cameroon. Hospitals and healthcare facilities should prioritize offering thorough instruction on PPE use and pinpoint the need to adhere consistently to PPE rules to remove these obstacles. They should also ensure that all healthcare personnel have access to and a sufficient supply of the proper PPE. Through the organization of impromptu visits by surveillance teams to identify areas of support and training, there is a need for assistance from government bodies and public health groups in creating awareness of the security value of PPE use among healthcare professionals. There is a lack of PPE in health care settings in rural areas in Cameroon, thus a need for an adequate supply. Then can we put appropriate PPE policies and practices for HCWs in Cameroon, as they will keep to it.Healthcare professionals in Cameroon must comprehend that following PPE standards protects not just their selves from diseases but also their patients, coworkers, and communities. We are accountable for ensuring everyone's safety and well-being, and adhering to PPE regulations is an essential first step.

In this paper, an adaptive proportional and integral (PI) controller for speed control of electric drives is developed. The adaptive PI controller is designed based on model reference adaptive identification and the Lyapunov function so that the system stability can be proved. To identify the inertia, the viscous friction torque coefficient, and the load torque simultaneously and smoothly, sinusoidal speed reference is usually employed. A modified motion equation considering the low-pass filter for feedback speed and the Coulomb friction torque is introduced and the relationship between the identified parameters and their actual values are clarified. A high-precision digital simulation model is built based on MATLAB/Simulink. The effectiveness of the proposed method is verified by simulations under various conditions.

Fast-scan cyclic voltammetry (FSCV) is an electrochemical sensing technique that can be used for neurochemical sensing with high spatiotemporal resolution. Carbon fiber microelectrodes (CFMEs) are traditionally used as FSCV sensors. However, CFMEs are prone to electrochemical fouling caused by oxidative byproducts of repeated serotonin (5-HT) exposure, which makes them less suitable as a chronic 5-HT sensor. Our team is developing a boron-doped diamond microelectrode (BDDME) that has previously been shown to be relatively resistant to fouling caused by protein adsorption (biofouling). We sought to determine if the BDDME exhibits resistance to electrochemical fouling, which we explored on electrodes fabricated with either femtosecond laser cutting or physical cleaving. We recorded the oxidation current response after 25 repeated injections of 5-HT in a flow-injection-cell and compared the current drop from the first to the last injection. The 5-HT responses were compared to dopamine (DA), a neurochemical that is known to produce minimal fouling oxidative byproducts and have a stable repeated response. Physical cleaving of the BDDME yielded a reduction in fouling due to 5-HT compared to the CFME and the femtosecond laser cut BDDME. However, the femtosecond laser cut BDDME exhibited a large increase in sensitivity over the cleaved BDDME. An extended stability analysis was conducted for all device types following 5-HT fouling tests. This analysis demonstrated an improvement in the long-term stability of boron doped diamond over CFMEs, as well as a diminishing sensitivity of the laser cut BDDME over time. This work reports the electrochemical fouling performance of the BDDME when it is repeatedly exposed to DA or 5-HT, which informs the development of a chronic, diamond-based electrochemical sensor for long-term neurotransmitter measurements in vivo.

In this paper, the filtering method of biomedical image denoising is described comprehensively. Firstly, it introduces the biomedical image denoising, describes the relationship between biomedical image denoising and medical care, introduces the filtering methods, the filtering methods of biomedical image denoising, the challenges encountered by the current filtering methods, and other application fields of filtering methods. Firstly, the background of biomedical image denoising is introduced. Biomedical image denoising is a challenge. Different imaging modes have different noise characteristics, and noise levels can vary greatly depending on the specific application. Secondly, it describes that biomedical image denoising plays an important role in medical care, and the biomedical image directly affects the patient's diagnosis, treatment plan and the overall quality of medical care service. Then the filtering method is introduced in detail, describing the core concepts and related features of linear filtering, nonlinear filtering and frequency domain filtering, and then focusing on the adaptive filtering method, describing the characteristics, conditions of use, common algorithms and advantages of adaptive filtering method. Then the filter methods of biomedical image denoising are introduced, and the core concepts of Gaussian filter, median filter, total variation denoising and Wiener filter are introduced respectively. Then, the challenges encountered by filtering methods are described, such as the accurate selection of filters, the balance between noise reduction and image detail preservation are introduced. Finally, the application of filtering method in other fields is mentioned, such as audio processing, speech recognition and so on. In summary, this paper comprehensively expounds the denoising and filtering methods of biomedical images, the filtering methods of medical image denoising, the relationship between medical image denoising and medical care, and the challenges encountered by filtering methods.

Self-assembled structures mostly arises through enzyme-regulated phenomena in nature under persistent conditions. Enzymatic reactions are one of main biological processes in fabrication and construction of supramolecular hydrogel networks required for biomedical applications. The enzymatic processes provide a unique opportunity to integrate hydrogel formation. In most of cases, structure and substrates of hydrogels are adjusted by enzyme catalysis due to the chemo-, regio- and stereo-selectivity of enzymes. Hydrogels processed by using various enzyme schemes showed remarkable characteristics as dynamic frames for cells, bioactive molecules and drugs in biomedical applications. A novel class of enzyme-mediated crosslinking hydrogels mimics the extracellular matrices by displaying unique physicochemical properties and functionalities like water-retention capacity, drug loading ability, biodegradability, biocompatibility, biostability, bioactivity, optoelectronic properties, self-healing ability, shape memory ability. In recent years, many enzymatic systems investigated hydrogel cross-linking. Results of biocompatible hydrogel products show that these mechanisms of crosslinking can fulfill requirements for variety of biomedical applications including tissue engineering, wound healing and drug delivery.

Hydrogels are used for various biomedical applications due to their biocompatibility, capacity to mimic the extracellular matrix, and ability to encapsulate and deliver cells and therapeutics. However, traditional hydrogels have a few shortcomings, especially regarding their physical properties, thereby limiting their broad applicability. Recently, researchers have investigated the incorporation of nanoparticles (NPs) into hydrogels to improve and add to the physical and biochemical properties of hydrogels. This brief review focuses on papers that describe the use of nanoparticles to improve more than one property of hydrogels. Such multifunctional hydrogel nanocomposites have enhanced potential for various applications, including tissue engineering, drug delivery, wound healing, bioprinting and biowearable devices.

Over the years, there has been a significant rise in the world's scientific knowledge. However, most of it lacks structure and is often termed as Dark Data. Both humans and expert systems have continually faced difficulty in analyzing and comprehending such overwhelming amounts of information which is crucial in solving several real-world problems. Information and data visualization techniques proffer a promising solution to explore such data by allowing quick comprehension of information, the discovery of emerging trends, identification of relationships and patterns, etc. In this tutorial, we utilize the rich corpus of PubMed comprising of more than 30 million citations from biomedical literature to visually explore and understand the underlying key-insights using various information visualization techniques. With this study, we aim to diminish the limitation of human cognition and perception in handling and examining such large volumes of data by speeding up the process of decision making and pattern recognition and enabling decision-makers to fully understand data insights and make informed decisions.

Aiming at the problem of small size of some spots on apple leaves and the difficulty of accurate detection of spot targets brought by the complex background of the orchard, this paper takes the alternaria leaf spot, rust, brown spot, grey spot and frog eye leaf spot on apple leaves as the research object, and proposes a high-accuracy detection model YOLOv5-Res and lightweight detection model YOLOv5-Res4 are proposed. Firstly, a multiscale feature extraction module ResBlock is designed by combining the Inception multi-branch structure and ResNet residual idea. Secondly, a lightweight feature fusion module C4 is designed to reduce the number of model parameters while improving the detection ability of small targets. Finally, a parameter streamlining strategy based on optimized model architecture is proposed. The experimental results show that the performance of YOLOv5-Res model and YOLOv5-Res4 model is significantly improved, the [email protected] value is improved by 2.8% and 2.2% compared with YOLOv5s model and YOLOv5n model, respectively, and the size of YOLOv5-Res model and YOLOv5-Res4 model is only 10.8MB and 2.4MB, and the number of model parameters is reduced compared with YOLOv5s model and YOLOv5n model. counts are reduced by 22% and 38.3% compared to the YOLOv5s model and YOLOv5n model.

Underwater image often exhibit detail blurring and color distortion due to light scattering, impurities, and other influences, obscuring essential textures and details. This presents a challenge for existing super-resolution techniques in identifying and extracting effective features, making high-quality reconstruction difficult. This research aims to innovate underwater image super-resolution technology to tackle this challenge. Initially, an underwater image degradation model was created by integrating random subsampling, Gaussian blur, mixed noise, and suspended particle simulation to generate a highly realistic synthetic dataset, thereby training the network to adapt to various degradation factors. Subsequently, to enhance the network's capability to extract key features, improvements were made based on the symmetrically structured Blind Super-Resolution Generative Adversarial Network (BSRGAN) model architecture. An attention mechanism based on energy functions was introduced within the generator to assess the importance of each pixel, and a weighted fusion strategy of adversarial loss, reconstruction loss, and perceptual loss was utilized to improve the quality of image reconstruction. Experimental results demonstrate that the proposed method achieved significant improvements in Peak Signal-to-Noise Ratio (PSNR) and Underwater Image Quality Measure (UIQM) by 0.85 dB and 0.19, respectively, significantly enhancing the visual perception quality and indicating its feasibility in super-resolution applications.

Gene editing is now easy to make new disease models through in-vivo and in vitro tests. It can potentially be used to make animals with single-gene or multiple-gene changes. The mutant strains with changed germlines are no longer needed with in vivo gene editing, which uses the CRISPR-Cas9 system to target cells of interest in their normal tissues. Whereas, the AAVs and other viral vectors have made it possible to change cells selectively. Gene editing hade made it possible to use human induced pluripotent stem cells (iPSC) to model diseases that run in families. Researchers can compare and contrast the human genomes of many different ethnic and racial groups using this method. Scientists may be able to make a disease in a lab dish using iPSCs from a patient. Using CRISPR, iPSCs made from patient cells can be fixed if they have certain problems. This shows that gene therapy is possible and shows what happens when cells aren't working right. The fact that CRISPR-Cas9 can change the DNA by just one nucleotide has had a huge effect on biological studies. CRISPR is becoming more and more popular, which shows how useful, easy, and effective it is. With the broad use of CRISPR-based apps, the tool is now used for much more than just changing genes. This method can be used to screen the whole genome, control the translation of genes based on their sequence, and edit several genes at the same time. Scientists can now model diseases in different species and learn more about how genes work because of these advances. Genome-wide association studies and genome-editing tools like CRISPR are giving us a good look at the future of personalized medicine.

Diabetes mellitus, a chronic and non-transmissible disease, triggers a wide range of micro- and macrovascular complications. The differentiation of pancreatic β-like cells (PβLCs) from induced pluripotent stem cells (iPSCs) offers a promising avenue for regenerative medicine aimed at treating diabetes. Current differentiation protocols strive to emulate pancreatic embryonic development by utilizing cytokines and small molecules at specific doses to activate and inhibit distinct molecular signaling pathways, directing the differentiation of iPSCs into pancreatic β cells. Despite significant progress and improved protocols, the full spectrum of molecular signaling pathways governing pancreatic development and the physiological characteristics of the differentiated cells are not yet fully understood. Here, we report a specific combination of cofactors and small molecules that successfully differentiate iPSCs into PβLCs. Our protocol has shown to be effective, with the resulting cells exhibiting key functional properties of pancreatic β cells, including the expression of crucial molecular markers (pdx1, nkx6.1, ngn3) and the capability to secrete insulin in response to glucose. Furthermore, the addition of vitamin C and retinoic acid in the final stages of differentiation led to the overexpression of specific β cell genes.

Radio-dynamic therapy (RDT), as an emerging cancer treatment method, has attracted attention due to its remarkable therapeutic efficacy using low-dose, high-energy radiation (such as X-rays), and has shown significant potential in cancer treatment. The RDT system typically consists of scintillators and photosensitizers. Scintillators absorb X-rays and convert them to visible light, activating nearby photosensitizers to generate cytotoxic reactive oxygen species (ROS). Challenges faced by the two-component strategy, including low loading capacity and inefficient energy transfer, hinder its final effectiveness. In addition, the tumor microenvironment (TME) with hypoxia and immunosuppression limits the efficacy of RDTs. Recent advances introduce one-component RDT systems based on nanomaterials with high-Z metal elements, which effectively inhibit deep-seated tumors. These novel RDT systems exhibit immune enhancement and immune memory, potentially eliminating both primary and metastatic tumors. This review comprehensively analyzes recent advances in the rational construction of RDTs, exploring their mechanisms and its application in the treatment of deep-seated tumors. Aimed at providing a practical resource for oncology researchers and practitioners, the review offers new perspectives for potential future directions in RDT research.

The classification of kidney tumors has undergone a remarkable evolution since the early 19th century, reflecting advances in medical science and technology. This historical overview traces the development of renal tumor classification, beginning with early clinical observations and macroscopic descriptions to the integration of molecular diagnostics in contemporary classifications. The establishment of international organizations like the World Health Organization (WHO) facilitated collaboration and standardization in tumor classification, leading to refined classifications and standardized nomenclature. Advancements in histological and molecular studies, particularly genetic analyses, revolutionized the understanding of renal cell carcinomas, enabling precise categorization based on molecular characteristics. The journey from rudimentary classifications to sophisticated systems based on detailed histological, immunohistochemical, and molecular criteria underscores the continuous evolution of kidney tumor classification. This article provides a comprehensive overview of this evolution, highlighting the contributions of scholars and the impact of technological advancements on our understanding and management of kidney tumors.

Thrombosis is the pathological clot formation under abnormal hemodynamic conditions, which can result in vascular obstruction, causing ischemic strokes and myocardial infarction. Thrombus growth under moderate to low shear (<1000 s^-1) relies on platelet activation and coagulation. Thrombosis at elevated high shear rates (>10,000 s-1) is predominantly driven by unactivated platelet binding and aggregating mediated by von Willebrand factor (VWF), while platelet activation and coagulation are secondary in supporting and reinforcing the thrombus. Given the molecular and cellular level information it can access, multiscale computational modelling informed by biology can provide new pathphysiological mechanisms that are otherwise not accessible experimentally, holding promise for novel first-principle-based therapeutics. In this review, we summarize the key aspects of platelet biorheology and mechanobiology, focusing on the molecular and cellular scale events and how they build up to thrombosis through platelet adhesion and aggregation in the presence or absence of platelet activation. In particular, we highlight recent advancements in multiscale modeling of platelet biorheology and mechanobiology and how they can lead to better prediction and quantification of thrombus formation, exemplifying the exciting paradigm of digital medicine.

The issue of equipment layout in multi-floor satellites consists of two primary parts: allocating the equipment to the satellite's layers and placing the equipment in each layer individually. In reviewing the past literature in this field, firstly, the issue of assigning equipment to layers is observed in a few articles and next in the layout part, the non-overlapping constraint has always been a challenge, particularly for components that do not have a circular cross-section. In addition to presenting a heuristic method for allocating equipment to different layers of the satellite, this article presents a robust flexible programming model (RFPM) for the placement of equipment at different layers, taking into account the inherent flexibility of the equipment in placement and the subject of uncertainty. This model is based on the existing uncertainty between the distances of cuboid equipment which has not been addressed in any of the previous research, and by comparing its outputs with cases from past studies, it demonstrates a significantly higher efficiency in placing the equipment and meeting the limit of non-overlapping constraints between the equipment. Finally, it would be possible to reduce the design time in the conceptual and preparatory stages, as well as the satellite's overall size, while still satisfying other constraints like stability and thermal limitations, moments of inertia and centre of gravity.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

Traditional Medicine (TM) is a culturally-rooted healthcare practice, and its use, including for treating illnesses among children, has been reported in many countries. Despite the cultural significance of TM in managing children’s illnesses, evidence suggests that child mortality remains high in many settings. This indicates that the sole use of TM within families and communities might act as a barrier to using biomedical services, contributing to avoidable deaths. Globally, Indonesia is in the top 10 countries with the highest child mortality rates. In addition, Belu is a district in East Nusa Tenggara province, Indonesia that exhibits a high number of child deaths within the last three years. However, the use of TM for the treatment of illnesses among children in Indonesia has received minimal academic attention. This study aimed to understand parental beliefs, knowledge, views, and perceptions of TM and the impact on the use of TM and biomedical services in the treatment of illnesses among their children in Belu district, Indonesia. The participants (n=25) were parents with the real-life experiences of using TM for treating their children’s illnesses. They were recruited using the snowballing sampling technique. Data were collected using in-depth qualitative interviews. A thematic data analysis was performed and guided by a qualitative data analysis framework. The findings were grouped into four main themes: (i) parental beliefs, knowledge, views, and perceptions of TM, (ii) the influence of these factors on parental use of TM and biomedical services for the treatment of children’s illnesses, (iii) social and cultural influences on the use of TM and biomedical services among their children, and (iv) the impact of the sole use of TM or late medical diagnosis on the health condition and the death of children. The findings show that the use of TM is a common practice within families and communities in Belu, however evidence suggests that child mortality remains high in the setting, indicating less effectiveness of the sole use of TM. Thus, there is a need for the development of collaborative models of healthcare programs and service delivery fostering mutual respect and understanding between traditional healers and healthcare professionals, which could significantly contribute to improving parental use of biomedical services for the treatment of their children’s illnesses.

There is little doubt that the efficacy of MnDPDP and its therapeutic improved counterpart Ca4Mn(DPDP)5 mainly depends on their MnSOD-mimetic activity when it comes to their potential use as rescue medicines, during e.g., acute myocardial infarction. However, pharmacokinetic considerations suggest that the efficacy of MnDPDP on Pt2+-associated neurotoxicity depends on another action of this drug. Electron Paramagnetic Resonance (EPR) studies have demonstrated that Pt2+ outcompetes Mn2+ and endogenous Zn2+ from binding to fodipir (DPDP), and hence suggest that the previously reported CIPN protective efficacy of MnDPDP is a result of chelation and elimination of Pt2+ by DPDP, which in turn suggests that Mn2+ is unnecessary for efficacy when it comes to oxaliplatin-associated CIPN.

Diabetes mellitus is a chronic metabolic disease that affects over 10.5 percent of the global adult population. Biochemical and hematological parameters such as albumin (ALB) and red cell dis-tribution width (RDW) have been shown to be altered in diabetic patients. This study aims to cor-relate hematological and biochemical parameters with glycated hemoglobin (HbA1c). 777 adult individuals (372 women and 405 men, aged 19-85 years) were divided into three groups: 218 par-ticipants with HbA1c < 5.7% (group A: non diabetic), 226 with HbA1c ≥ 5.7% and < 6.5% (group B: prediabetic) and 333 with HbA1c ≥ 6.4% (group C: diabetic). Biochemical and hematological parameters were compared among the 3 groups. Analysis of variance was performed to deter-mine the correlations of the parameters among groups. ALB and sodium (Na) levels were signifi-cantly decreased in group C compared to groups A (ALB: 3.8 g/dL vs. 4.1 g/dL, p < 0.0001, Na: 138.4 mmol/L vs. 139.3 mmol/L, p < 0.001), and B (ALB: 3.8 g/dL vs. 4.0 g/dL, p < 0.0001, Na: 138.4 mmol/L vs. 139.6 mmol/L, p < 0.0001), while RDW-standard deviation (RDW-SD) and urea were increased in group C compared to group A ( RDW: 45.8 vs. 43.9 fL, p < 0.0001, Urea: 55.6 mg/dL vs. 38.5 mg/dL, p < 0.0001) . Mean platelet volume (MPV) was increased in group C com-pared to group A (9.3 fL vs. 9.1 fL, p < 0.05, respectively). Τhe increase of RDW-SD from group A towards B and C demonstrates the impact of hyperglycemia on red blood cells. RDW may be re-garded as a potential innovative biomarker for improving risk assessment of developing diabetes. These results highlight the potential role of these parameters as an indication for prediabetes that would alert for measurement of HbA1c.

Institutionalized older adults often face complex medication regimens, increasing their risk of adverse drug events due to polypharmacy, overprescribing, medication interactions or the use of Potentially Inappropriate Medications (PIM). However, data on medication use and associated risks in this population remain scarce. This pilot study aimed to characterize the sociodemographic, clinical and pharmacotherapeutic profiles and the use of PIM among institutionalized elders residing in Residential Structures for Elderly People (ERPI) in the Faro municipality, located in the Portuguese region of the Algarve. We conducted a cross-sectional study in a non-randomized sample of 96 participants (mean age: 86.6 ±7.86 years) where trained researchers reviewed medication profiles and identified potentially inappropriate medications using the EU(7)-PIM list. Over 90% of participants exhibited polypharmacy (≥5 medications), with an average of 9.1 ± 4.15 medications per person. About 92% had potential drug interactions, including major and moderate interactions. More than 86% used at least one potentially inappropriate medication, most commonly central nervous system drugs. This pilot study demonstrates that institutionalized older adults may be at high risk of potential medication-related problems. Implementing comprehensive medication review programs and promoting adapted prescribing practices are crucial to optimize medication use and improve the well-being of this vulnerable population.

Due to bacterial contamination, natural medicinal preservatives may be an alternative to enhance the quality of milk. Besides, thorough biocompatibility testing is deemed essential before integrating natural extracts into food products. To address this matter, our research focused on evaluating the antimicrobial potential of Plectranthus amboinicus, Flueggea leucopyrus, Cymbopogon citratus, and Bacopa monnieri against prevalent foodborne pathogens, including Staphylococcus aureus, Escherichia coli, Salmonella spp, and Pseudomonas aeruginosa and investigating the efficacy of plant extracts as natural preservatives along with biocompatibility and toxicity assessments. The methanolic extracts of plant materials were used for measuring antimicrobial activity using the agar well diffusion method, Minimum Inhibitory Concentration (MIC) and Minimum bactericidal concentration (MBC) assays. The preservative activity was tested by isolating pathogenic organisms in a sterilized milk medium and toxicity and biocompatibility was assessed using zebrafish embryo and brine shrimp lethality assays. At a concentration of 400 mg/ml, all plant extracts demonstrated notable activity against bacterial strains. B. monnieri at 400 mg/ml exhibited particularly significant effects on S. aureus (30.3 mm ± 0.6), surpassing the positive control, gentamicin (28.3 mm ± 0.6), while also displaying pronounced activity against E. coli. F. leucopyrus, at the same concentration, showed antimicrobial activity comparable to the positive control against both S. aureus (28.0 mm ± 1.0) and E. coli (27.0 mm ± 1.0). However, as there’s weak-mild toxicity in these herbs, prior to consumption, careful consideration of their toxicity and biocompatibility is imperative for ensuring their safe use.

Biosurfactants (BSs) are microbial compounds that have emerged as potential alternatives to chemical surfactants due to their multifunctional properties, sustainability, and biodegradability. Owing to their amphipathic nature and distinctive structural arrangement, biosurfactants exhibit a range of physicochemical properties, including excellent surface activity, efficient critical micelle concentration, humectant properties, foaming and cleaning abilities and the capacity to form microemulsions. Furthermore, numerous biosurfactants display additional biological characteristics, such as antibacterial, antifungal, and antiviral effects, antioxidant, anticancer, and immunomodulatory activities. Over the past two decades, numerous studies have explored their potential applications, including pharmaceuticals, cosmetics, antimicrobial and antibiofilm agents, wound healing, anticancer treatments, immune system modulators and drug/gene carriers. These applications are particularly important in addressing challenges such as antimicrobial resistance and biofilm formation in clinical, hygiene, and therapeutic settings. They can also serve as coating agents for surfaces, enabling antiadhesive, suppression, or eradication strategies. Not least importantly, biosurfactants have shown compatibility with various drug formulations, including nanoparticles, liposomes, micro and nanoemulsions, and hydrogels, improving drug solubility, stability, and bioavailability and enabling targeted and controlled drug release. These qualities make biosurfactants promising candidates for the development of next-generation antimicrobial, antibiofilm, anticancer, wound healing, immunomodulating, drug or gene delivery agents, as well as adjuvants to other antibiotics. Analyzing recent literature, this review aims to provide insights into the present understanding, highlight emerging trends, identify promising directions and advancements in the utilization of biosurfactants within the pharmaceutical and biomedical fields.

The prospective applications of chitosan-based hydrogels (CBHs), a category of biocompatible and biodegradable materials, in biomedical disciplines such as tissue engineering, wound healing, drug delivery, and biosensing have garnered great interest. The synthesis and characterization processes used to create CBHs play a significant role in determining their characteristics and effectiveness. The processing procedure could be tailored to obtain specific features like porosity, swelling, mechanical strength, degradation rate, and bioactivity, affecting the properties of CBHs to a great extent. Additionally, characterization methods aid in gaining access to the microstructures and properties of CBHs. Especially, this review provides a comprehensive assessment of the state-of-the-art with a focus on the affiliation between particular properties and application domains. The main obstacles and prospects for the future of CBH development for biomedical applications are also covered in the review.