In this study, an alternative method to conventional production methods involving thin section copper permanent mould casting (rapid solidification), hot rolling and heat treatment processes to manufacture AISI DC 53 cold work tool steel, has been investigated. In this new method, solidification of the AISI DC 53 was done in the thin section copper mould instead of traditional ingot casting. After solidification, thin slabs obtained was homogenized to 1150 ^oC and hold at this temperature for one hour and then hot rolling was be applied. During hot rolling process, about % 30 reduction in thickness of slab was obtained. After hot rolling, heat treatment (austenitizing, quenching and tempering) have been applied to thin slab. The samples have been taken as cast, as rolled and as heat treated (austenitized and tempered) and the microstructural analysis, hardness tests, retained austenite quantity measurement by XRD method have been performed. The heat treatment and tests have been performed for a commercially available AISI DC 53 which is manufactured by thick section ingot casting and rolling. Hardness values of the AISI DC 53 steels produced by traditional route is in the range of 52-54 HRC after austenitization at 1025 ^oC for one hour and quenched in compressed air and tempered twice at 525 ^oC for 120 mins. On contrary the permanent mould cast AISI DC 53 after homogenization at 1150 ^oC and immediately hot rolling then air cooling and austenitized at 1025 ^oC for one hour then quenched by compressed air and tempered twice at 525 ^oC for 120 mins have hardness valeus in the range of 55-57 HRC. Experiments have revealed that the properties of new rapid solidified steel in permanent copper mould are better than the commercially available steel and have a more refined microstructure than commercially produces alternative. Therefore, the new proposed method can be used as an alternative manufacturing method for cold-work tool steels.

Silicon carbide single crystal (SiC) has been widely used in the field of power devices, while it is difficult to fabricate ultra-flat surface by traditional manufacturing technologies due to its difficult-to-machine property. This paper investigates the interaction process during femtosecond laser ablation of crystalline silicon carbide based on the two-temperature model simulation and experimental study. The findings reveal that parameters such as laser pulse energy, scanning interval, and defocus amount exert significant influence on ablation depth, roughness, and surface morphology. The femtosecond laser proves effective in removing surface defects from cut SiC substrates, albeit resulting in increased surface roughness. However, subsequent polishing treatment of the laser-ablated silicon carbide surface can mitigate this roughness, underscoring the feasibility of laser surface ablation for silicon carbide single crystals.

In this paper, the deformation behavior of S32750 duplex stainless steel during low cycle fatigue was studied by controlling number of cycles. The microstructure of the specimens under different cycles was characterized by optical microscope (OM), scanning electron microscope (SEM), electron backscatter diffraction (EBSD) and transmission electron microscope (TEM). Microhardness of two phases was measured by a digital microhardness instrument. The results showed that the microhardness of ferrite increases significantly after the first 4000 cycles, while the austenite shows a higher strain hardening rate after fatigue fracture, and the microhardness of ferrite and austenite increases by 23 HV and 87 HV, respectively. Two-phase kernel average misorientation (KAM) diagram showed that the continuous accumulation of plastic deformation easily leads to the initiation of cracks inside the austenite and at the phase boundaries. The evolution of dislocation morphology in two phases was obviously different. With the increase of cycle number, the dislocation in ferrite gradually transforms from dislocation bundles and dislocation array to sub-grain structure, while the dislocation in austenite gradually develops from dipole array to ordered Taylor lattice network structure.

The fatigue strength of the hot work steel depends on various factors, including the mechanical, properties and behavior and bulk and the surface under layer, the microstructural features as well as heat treatments. The influence of a series of heat treatments on the fatigue strength of H13 hot work steel was investigated. Different preheating, quenching and tempering treatments were applied to four sets of specimens and fatigue tests were conducted at room temperature using a rotating bending test machine. All heat treatments resulted in a certain improvement of the fatigue strength. Highest fatigue strength obtained by applying a double tempering heat treatment (first tempering at 550 °C for two hours and second tempering at 610 °C for two hours) after initial preheating and quenching. One tempering treatment (550 °C for two hours after preheating and quenching) did not significantly improve the fatigue strength.

It is important to realize the transformation behavior of wüstite because it greatly affects the final structure of the oxide layer and the surface quality of the steel products. In the present study, the transformation behaviors of the wüstite layer are examined under nearly-oxygen-free conditions, to simulate the cooling processes after the hot rolled strip is coiled. As the single phase wüstite was prepared at 950˚C, the 460˚C transformed oxide layer was composed of a mixture of iron and magnetite formed through eutectoid reactions. For the 750˚C-fabricated wüstite, only magnetite was observed after transformation, without iron precipitates and residual wüstite. It is speculated that the unusual transformation behavior of the low-temperature-made wüstite results from the pseudo-structural intermediate phase transformation between wüstite and magnetite. This pseudo-structure is a pre-transformed wüstite and of various concentration of ferrous ion, which is determined by the fabrication conditions. During the hot strip mill process, the so-called wet scale, wüstite, is produced continuously from finish mill to laminar flow sections and ended at 570˚C. Consequently, the final eutectoid transformation below 570˚C is dominantly controlled by the surface temperature ranged from 750˚C to 950˚C for low carbon steel.

The precipitate phases often play an important influence on the corrosion resistance of 2205 Duplex stainless steel (DSS). In the presented paper, the microstructure and corrosion resistance in the hot-rolled and cold-rolled 2205 DSS aging for different time at 850 °C was investigated by XRD, SEM and potentiodynamic polarization. It has been found that the Chi(χ) phase and Sigm(σ) phase were precipitated in turn after aging treatment of hot-rolled and cold-rolled materials, but the precipitate amount in cold-rolled material is much more than that of hot-rolled samples. The corrosion resistance of the solution-annealed cold-rolled material is similar to the hot-rolled material, but the corrosion resistance of cold-rolled material with precipitate is weaker than that of hot-rolled material after aging treatment. Pitting initiates preferentially in the Cr-depleted region from σ phase in aged hot-rolled 2205, and severe selective corrosion occurs on sigma/ferrite interfaces aged for a long aged lime. However, the initiation of pitting corrosion may take place at the phase boundary, defect and martensite in the aged cold-rolled 2205. The σ phase is further selectively dissolved by electrochemical method to investigate the difference of microstructure and corrosion behavior in hot-rolled and cold-rolled 2205 duplex stainless steel.

Iron powders having average particle sizes of ~40µm are mechanically mixed thoroughly with aluminum powders ranging from 1 to 10 in wt.% with an average particle size of ~10µm. Two different powder metallurgical techniques cold and hot pressing are used to study the effect of the additive element powder on the mechanical properties, wear properties and the microstructure of the iron based alloys. The hot pressing technique was performed at a temperature up to 500°C at 445.6 MPa. The cold pressing technique was performed at 909 MPa in room temperature. By increasing the Al content to 10 wt. % in the base Fe-based matrix, the hardness was decreased from 780 to 690 MPa and the radial strength was decreased from 380 to 202 MPa with reductions of 11.5% and 40%, respectively. Improvement of the wear resistance with the increase addition of the Al powder to the Fe matrix up to 5 times was achieved compared to the alloy without Al addition for different wear parameters namely; wear time and sliding speed.

Quantifying the landscape pattern change can effectively demonstrate the ecological progresses and the consequences of urbanization. Based on remotely sensed land cover data in 1994, 2000, 2006 and a gradient analysis with landscape metrics at landscape- and class- level, we attempted to characterize the individual and entire landscape patterns of Shanghai metropolitan during the rapid urbanization. We highlighted that a roadscape transect approach that combined the buffer zone method and the transect-based approach was introduced to describe the urban-rural patterns of agricultural, residential, green, industrial, and public facilities land along the railway route. Our results of landscape metrics showed significant spatiotemporal patterns and gradient variations along the transect. The urban growth pattern in two time spans conform to the hypothesis for diffusion–coalescence processes, implying that the railway is adaptive as a gradient element to analyze the landscape patterns with urbanization. As the natural landscape was replaced by urban landscape gradually, the urban fringe expanded radically. The results also showed that the desakota region expanded its extent widely. Satellite towns witnessed the continual transformation from the predominantly rural landscape to peri-urban landscape. Furthermore, the gap between urban and rural areas remained large especially in public service. More reasonable urban plans and land use policies should push to make more of an effort to transition from the urban-rural separation to coordinated urban-rural development. This study is a meaningful trial in demonstrating a new form of urban–rural transects to study the landscape change of large cities from a strategic viewpoint. By combining gradient analysis with landscape metrics, we addressed the process of urbanization both spatially and temporally, and provided a more quantitative approach to urban studies.

Water resources provided by alpine glaciers are an important pillar for people living in the arid regions in the west of China. In this study, the HBV (Hydrologiska Byrans Vattenavdelning) light model was applied to simulate glacier mass balance and runoff in the Koxkar River Basin (KRB) on the south slope of Mt. Tumur, western Tianshan Mts.. Daily temperature and precipitation were calculated by multiple linear regressions and gradient-inverse distance weighting, respectively, based on in-situ observed data by automatic weather stations (AWSs) in the basin (2007–2009) and at four meteorological stations neighbering the basin (1959–2009). Observed daily air temperature and precipitation were taken as input data for the HBV model, which was calibrated using runoff in 2007/08 and 2009/10, and validated in 2008/09 and 2010/11. Generally, the model could simulate runoff very well. The annual glacier mass balance and runoff were calculated using the HBV model driven by interpolated meteorological data for the period of 1959–2009. The simulated glacier mass balance were reasonable when compared with those observed values at nearby glaciers, indicating a decrease trend of mass balance in the basin with an average value of –370.4 mm a^-1 since 1959. The annual runoff showed a slight increase trend (5.51 mm a^-1). Futher analysis indicated that the runoff is more sensitive to temperature than precipitation amuont in the Koxkar river basin.

The efficiency of cold sheet and strip rolling of steels and non-ferrous metals in the main depends on the quality of the technological lubricant and its cost. In this regard, it is important to develop new compositions of effective metal-working coolants (MWC) having low cost and providing the maximum reduction in the friction coefficient. We developed and tested the new compositions of the MWC on basis of chicken fat, and mono- and diglycerides and their esters of boric acid synthesized from the wastes of sunflower oil production. The MWC were tested in DSEA on laboratory rolling mill 100x100 with a roll diameter of 260 mm during steel 08Kp rolling. The efficiency of the coolants was determined by the factor of metal stretch forming λ and the coefficient of friction μ in the deformation zone which was found by forward slip method. We found the metal-working coolant with 100 % concentration of boric acid esters of mono- and diglycerides is the most effective in steel rolling. Thus the new MWC on basis of boric acid esters of mono- and diglycerides synthesized from the wastes of sunflower oil production can be recommended for use in rolling of structural steels on account of availability, high efficiency, and a low cost.

According to a recent estimate by UN Habitat, approximately 3 billion individuals will require suitable housing by the year 2030. This staggering demand translates to the need for around 96,000 affordable housing units to be constructed each day. However, the conventional construction methods that rely on cement-based concrete and masonry are outdated, lacking innovation, efficiency, and sustainability. In light of these challenges, cold-formed steel emerges as an appealing alternative to traditional construction materials like masonry and concrete. It offers numerous advantages, including easy fabrication, lightweight properties, energy efficiency, the ability to reuse the material at the end of its service life, and a higher level of recyclability. Cold-formed steel buildings are also recognized for their superior insulation and lower energy consumption during operation. Cold-formed steel (CFS) members are created by rolling structurally sound steel sheets into the required shapes using a forming machine, without the need for heat as in the case of hot-rolled steel. While the thickness of these members can range from 0.01 mm to 7 mm, commercial construction of load-bearing walls, roof trusses, and floor joists typically utilizes steel thicknesses of 0.7 mm to 1.2 mm. This paper tries to illustrate the materials and methods employed in the construction of cold-formed steel modular buildings in Sri Lanka[1]. It delves into the material and durability characteristics of cold-formed steel, the design philosophy behind these structures, the development of the building envelope, and the energy efficiency features of the building elements. The findings of this study demonstrate that cold-formed steel buildings can be a highly sought-after alternative for residential construction, offering faster construction timelines, cost-effectiveness, and energy-efficient practices.

In order to comprehensively evaluate the employee satisfaction of mine occupational health and safety management system, an analytic method based on fuzzy analytic hierarchy process and 2- tuple linguistic model was established. Firstly, based on the establishment of 5 first- grade indicators and 20 second- grade ones, the weight of each indicator is calculated and validated by method of FAHP and root mean square model. Secondly, a path based on the time-ordered Weighted Averaging Operator (T-OWA) model is constructed. Finally, the model is validated by empirical analysis. The results demonstrate that the employee satisfaction of the mine occupational health and safety management system is of the “general” rank. The method including the comprehensive evaluation of employee satisfaction and the quantitative analysis of language evaluation information ensures the authenticity of the language evaluation information.

Eco-friendly and low-cost water-based nanolubricants containing rutile TiO2 nanoparticles (NPs) were developed for accelerating their applications in industrial-scale hot steel rolling. The lubrication performance of developed nanolubricants was evaluated in a 2-high Hille 100 experimental rolling mill at a rolling temperature of 850 ℃ in comparison to that of pure water. The results indicate that the use of nanolubricant enables to decrease the rolling force, reduce the surface roughness and the oxide scale thickness, and enhance the surface hardness. In particular, the nanolubricant consisting of 4 wt% TiO2, 10 wt% glycerol, 0.2 wt% sodium dodecyl benzene sulfonate (SDBS) and 1 wt% Snailcool exhibits the best lubrication performance by lowering the rolling force, surface roughness and oxide scale thickness up to 8.1%, 53.7% and 50%, respectively. The surface hardness is increased by 4.4%. The corresponding lubrication mechanisms are attributed to its superior wettability and thermal conductivity associated with the synergistic effect of rolling, mending and laminae forming that are contributed by TiO2 NPs.

This paper presents the results of an experimental and analytical study on the behavior of cold-formed thick-walled steel plates connected by a single bolt under double shear. Experimental studies were conducted on a total of 54 bolted connections fabricated from two thickness of cold-formed thick-walled steel plates with the nominal thickness of 6 mm and 10 mm. The effects of end distance, edge distance and steel plate thickness were investigated on the bolt bearing behavior. Codes of (modified) ANSI/AISC 360-16 and EN1993-1-8 were applied to predict failure modes and bearing resistance of connections and the predictions were compared with that of measurements. A method was proposed to calculate the elongation of bolt hole at ultimate load. The studies show that fractures occurred on shear planes of specimens failed by shear out due to reduced ductility caused by cold forming process. The modified ANSI/AISC gives the most accurate predictions of failure modes and bearing resistance. However, the bearing resistance will be overestimated if the reduction in area of shear planes caused by occurrence of fracture is ignored for specimens with end distance being higher than 2.0d0 and a reduction factor is needed for calculating bearing resistance of connections. The method proposed in our paper can predict the elongation of bolt hole very well.

In this paper, through high-temperature tensile tests of 55NiCrMoV7 steel, the high-temperature fracture behavior, microstructure evolution and carbide distribution characteristics of both thermal-mechanical coupling zone (fracture zone) and thermal stress zone (clamping zone) at different temperatures were studied. Intrinsic relationship between high temperature fracture and carbides types, distribution and size were revealed and evolution mechanism of microstructure near cracks in 55NiCrMoV7 hot-working die steel during high temperature deformation was clarified. Samples were stretched at different temperatures from 25 °C to 700 °C, and microscopic examinations were carried out by using SEM and TEM. The results showed that: With the increase of temperature, tensile strength and yield strength decreased, elongation and reduction of area increased, and fracture mode changed from brittle fracture to ductile fracture by transition temperature at about 400℃. During high temperature deformation, the grain dislocation density decreased, the tempered martensite decomposed, recovered, recrystallized, and then grain grew. M7C3 and M23C6 carbides precipitated and grew along the grain boundary, and a small amount of fine granular MC carbides were dispersed in the grain. The work done by the external force on the deformation zone would cause the temperature of it to be higher than tensile temperature, which provides thermodynamic conditions for the re-dissolution of small carbides near the fracture zone and the grain growth of large carbides, resulting in the decrease of small carbides and increase of large carbides in thermal-mechanical coupling zone.

The aim of the paper is to analyze the experimental results of the influence of elevated temperatures and strain rate on the mechanical and structural properties of steel 42CrMo4. The experiments were based on uniaxial tension and compression tests at high temperatures between 700 °C and 1000 °C and strain rates range 0.0018 - 0.1 s^-1. The influence of temperature and strain rate on yield stress, strain to fracture, hardness, structural changes, and fracture characteristics were analyzed. Due to the dynamic recrystallization phenomenon present during the hot tensile tests, an increase in the flow stress is observed at the beginning of the deformation, after which it decreases until the fracture. By increasing the deformation temperature from 700 °C to 1000 °C, the tensile stress decreases significantly for all strain rates. The increase in the strain rate leads to the increase in the tensile stress. In compression tests by increasing the strain rate, the true strain is slightly increasing, but this depends on the temperature. The non-uniformity of deformations obtained at different values of the strain rate and temperature were also analyzed. Analysis by scanning electron microscopy showed the ductile behavior of the material. The degree of damage of the material caused by the presence of cavities increases by increasing the deformation temperature. For all the presented deformation conditions, the presence of the fracture through the ductile fracture mechanism was produced by the localized of necking and the coalescence of microvoids. By increasing the deformation temperature and reducing the strain rate, the fracture behavior of 42CrMo4 steel can be improved.

Hot rolling tests of a low-alloy steel were conducted at a rolling temperature of 850 ℃ under different lubrication conditions, including benchmarks (dry condition and water) and water-based nanolubricants containing different concentrations of nano-TiO₂ from 1.0 to 8.0 wt%. The effects of nanolubricants on rolling force, surface roughness, thickness of oxide scale and microstructure were systematically investigated through varying nano-TiO₂ concentrations. The results show that the application of nanolubricants can decrease the rolling force, surface roughness and oxide scale thickness of rolled steels, and refine ferrite grains. In particular, the nanolubricant containing an optimal concentration (4.0 wt%) of nano-TiO₂ demonstrates the best lubrication performance, owing to the synergistic effect of lubricating film, rolling, polishing and mending generated by nano-TiO₂.

In the context of sustainable development, integrating the work aspect into health promotion systems is essential, ensuring that employees maintain a healthy balance between their professional and personal lives, which respects and amplifies the potential of every individual. Lately, there has been a noticeable shift of medical professionals from the public to the private sector. This trend paints a bleak picture, highlighting the vulnerabilities of a system teetering on the brink of failure, with significant impacts on patient care. Among the myriad reasons behind this shift, burnout stands out prominently. Medical professionals face increasing pressures due to understaffing, limited organizational support, and insufficient resources, leading to feelings of cynicism, exhaustion, and detachment from their roles. Utilizing the Maslach et al. questionnaire, we assessed the risk of burnout among physicians in public hospitals to identify and underscore preventive measures and improvements, correlating our findings with key aspects of organizational empowerment. Our research indicates that enhancing interpersonal relationships and resources—both within teams and between the organization and its physicians—is crucial for the revival of the healthcare system. This approach aims at improving the delivery of healthcare services and offering appropriate recognition to healthcare professionals, aligning with the principles of sustainable employment.

One of the major sources of catastrophic failures and deterioration of the mechanical properties of metals such as ductility, toughness, and strength, of various engineering components during application is hydrogen embrittlement (HE). It occurs as a result of adsorption, diffusion, and interaction of hydrogen with various metal defects like dislocations, voids, grain boundaries and oxide/matrix interfaces due to its small atomic size. Over the years, extensive effort has been dedicated to understanding hydrogen embrittlement sources, effects, and mechanisms. This research aimed at assessing the tensile properties; toughness, ductility, and susceptibility to hydrogen embrittlement, of cold-finished mild steel. Steel coupons were subjected to electrochemical hydrogen charging in a carefully chosen alkaline solution over a particular time and at various charging current densities. Tensile property tests were conducted immediately post the charging process, and the results were compared with those of uncharged steel. The findings revealed a clear drop in toughness and ductility with increasing hydrogen content. Fracture surfaces were examined to determine failure mechanisms. This evaluation has enabled the prediction of the steel's ability to withstand environments with elevated hydrogen concentrations during practical applications.

Cold gas-dynamic spray (cold spray) is an evolving coating deposition and restoration technology in which particles are deposited above the sonic speed. This paper presents the non-destructive three-dimensional characterization of cold sprayed stainless steel coating. The visualization of coating morphology and volumetric porosity, and the analyses of porosity size and spatial distributions confirmed that dense stainless steel coating with non-connected, micron-sized gradient porosity is successfully produced by cold spray. The suitability of X-ray tomography for characterizing cold sprayed coatings is assessed.

This article reports on the comparative study of the hot deformation behaviour of virgin (steel A) and rejuvenated heat treatment creep-exhausted (steel B) P91 steels. Hot uniaxial compression tests were conducted on the two steels at the deformation temperature range of 900°C-1050°C and a strain rate range of 0.01-10s-1 to 0.6 strain using Gleeble® 3500 equipment. The results showed that the flow stress largely depends on the deformation conditions. The flow stress for the two steels increased with an increase in strain rate at a given deformation temperature and vice versa. The flow stress-strain curves exhibited a dynamic recovery as the softening mechanism. The material constants determined using Arrhenius constitutive equations were: stress exponent was: steel A (5.76) and steel B (6.67), and the apparent activation energy was: steel A (473.1 kJ mol-1) and steel B (564.5 kJmol-1). From these results, steel A exhibited better workability than steel B. Statistical parameters analyses showed that the flow stress for the two steels had a good correlation between the experimental and predicted data. Pearson’s correlation coefficient (R) was: steel A (0.97) and steel B (0.98). The Average Absolute Relative Error (AARE) values were: 7.62% (steel A) and 6.54% (steel B). The study shows that the Arrhenius equations can effectively describe the flow stress behaviour of P91 steel, and this method is applicable to the industrial metalworking process.

Chilling injury (CI), which causes seed browning in pepper, may arise following long-term cold storage, and is a major cause of postharvest losses. To explore potential strategies of minimizing the associated postharvest losses, the present study investigated the optimal pepper harvest time that could reduce levels of seed browning, in addition to the relationship between fruit maturity and seed browning. Fruit harvested 15 days after flowering (DAF) were sensitive to cold storage at 4°C and exhibited 100% seed browning (CI index, 4.0); in contrast, the seed browning rate of fruit harvested 35 DAF was 10% (CI index, 0.4) within 7 d of cold storage. Seed antioxidant activity was higher in seeds harvested at early stages (15 DAF to 20 DAF) than in seeds harvested at later stages (40 DAF to 50 DAF) at the beginning of storage. Pericarps of fruit harvested at 50 DAF exhibited the highest antioxidant activity. Lipoxygenase, catalase, and peroxidase activity, and the expression levels of cell wall-related genes, pectin methylesterase-like protein, and endo-β-1,4-glucanase were higher in seeds of immature fruit harvested 15 DAF than in seeds of mature fruit harvested 35 DAF. The endosperm separated from the seed coat in fruit harvested 35 DAF and the seeds did not brown under low-temperature storage. The lack of seed browning observed in mature fruit under low-temperature storage could be attributed to physical protection provided by the seed coat rather than cold stress resistance conferred by antioxidants.

Q345 steel is widely used in the construction industry, vehicle manufacturing industry, bridge construction industry and many other aspects due to its excellent comprehensive performance. However, due to its high silicon content, direct hot-dip galvanizing will lead to a series of problems, such as easy peeling of the coating due to the "silicon reactivity". In this paper, we adopt the "two-step hot-dipping method", first hot-dip aluminizing and then hot-dip galvanizing, to isolate the substrate and zinc liquid direct contact, so as to avoid the occurrence of "silicon reactivity". Through the microstructure characterization, neutral salt spray corrosion experiments, electrochemical experiments, the results show that: Al-Zn composite coatings from the inside out were perpendicular to the substrate growth of loose Fe2Al5 layer and Al-Zn layer, outbursts generation; Al-Zn composite coatings resistance to neutral salt spray corrosion was far more than the substrate; Al-Zn composite coatings polarization curve corrosion potential than the substrate was lower than that of the substrate by 0.512V, showing a strong corrosion resistance. It shows extremely strong corrosion resistance.

Industries that rely on additive manufacturing of metallic elements, especially biomedical companies, require material science-based knowledge of how process parameters and methods affect element properties, but such phenomena are incompletely understood. In this study, we investigated the influence of selective laser melting (SLM) process parameters and additional heat treatment on mechanical properties. The research included structural analysis of residual stress, microstructure, and scleronomic hardness in low-depth measurements. Tensile tests with element deformation analysis using digital image correlation (DIC) were performed as well. Experiment results showed it was possible to observe the porosity growth mechanism and its influence on material strength. Elements manufactured with 20% lower energy density had almost half the elongation, which was directly connected with porosity growth during energy density reduction. Hot isostatic pressing (HIP) treatment allowed for a significant reduction of porosity and helped achieve properties similar to elements manufactured using different levels of energy density.

The article discusses early diagnosis and intervention for developmental delays in children, emphasizing the role of specialized services and personnel in supporting recovery and development. It presents findings from a pilot project initiated in Bucharest, aiming to assess the incidence of developmental delays in children aged 1-3 years in selected kindergartens, including ASD. The study involved children, parents, and specialists, utilizing systematic behavior observation (SBO) and semi-structured interviews. Results indicate that out of 613 evaluated children, 81 received specialized control recommendations, with 4 cases showing potential risk of ASD. Additionally, 8 children were diagnosed with autism. The incidence of autism in children aged 1-3 years was 1 in 51. Although exploratory, these findings suggest a model of good practice for future early diagnosis campaigns nationally. Conclusively, the study underscores the importance of early diagnosis and intervention for developmental delays, advocating for a responsive community and emphasizing the significance of national-level efforts to address these issues effectively.

The cold-formed steel sections are becoming popular for different steel structures because it has a high resistance against the different straining actions with minimum weight compared with hard steel sections. Recently, the perforated cold-formed steel (PCFS) sections are used in many applications such as storage perforated uprights racks. Experimental research into the behaviour of steel storage rack uprights subjected to axial compression is presented in this paper. The material qualities of cold-formed steel uprights were determined by tensile tests. The seventeen perforated specimens were examined under axial compression, with five different cross-sections, three different web heights and thicknesses, and varying lengths. The study's goals are to find out how perforations affect the performance and failure mode of steel storage rack uprights, discuss the interaction of distortional and global buckling, and verify the accuracy of using the Direct Strength Method (DSM) for predicting the ultimate strength of uprights failing in buckling interactions for perforated uprights. It is found that the failure modes of perforated specimens with stiffeners generally cannot be well predicted by the Direct Strength Method. But when the modifications proposed by Xianzhong Zhao etc. al. are used, their accuracy is acceptable.

Literature data on Legionella spp. presence in houses water networks have been increasing during the last years, but epidemiological reports assert a high incidence of Legionnaires’ disease infection in Italy. Updating our previously published data, we report a five-year survey on Legionella spp. colonization in 235 buildings with an independent hot water production (IB); 82 buildings with a central hot water production (CB); and 58 buildings with a solar thermal system for hot water production (TB). In all the 375 buildings Legionella spp. was researched in hot and cold water samples and microbiological potability standards of cold water were evaluated. Legionella spp. was detected in 27% of the water networks, mostly in CB and TB. We detected correlations between the presence of bacteria and some physical-chemical parameters (low chlorine level and optimal temperature for Legionella spp. growth). Cold water resulted free from microbiological hazards, except for coliform bacteria isolated in three separate cases, and Legionella spp., detected when cold water temperature was about 20°C. After a five-year survey we confirm the presence of a Legionnaires’ disease risk and the need of training programs for all the workers involved in residential water systems management.

In this study, the effect of hot stamping forming process on the properties change of compound layer in Al–Si coated high-strength steel sheet with different thickness was investigated. The coating layer in hot stamped high-strength steel sheet was composed of a diffusion layer and a compound layer. As the hot stamping temperature and holding time for forming increased, the thickness of the compound layer in the Al–Si coated high-strength steel sheet increased. The thickness of coating layer with the hot stamping for 500 sec at 890, 910 and 950 °C was obtained 8.9, 11.8, and 20.6 micrometer, respectively. The thickness of coating layer with hot stamping for 180, 500 and 550 sec at 910 ^oC was obtained 5.7, 11.8, and 17.8 micrometer, respectively. The compound layer in hot stamped high-strength steel sheet with Al–Si coating layer consists of Al_5.4Fe₂ and Fe₂Si phases. In the compound layer, Al and Si were irregularly distributed.

This paper presents the results of investigations of the effects of hot deformation parameters in compression investigation on the austenite grain size in HSLA steel (0.16% C, 0.037% Nb, 0.004% Ti, 0.0098% N). The axisymmetric compression investigations were performed on cylindrical investigation specimens of d=1.2 using the Gleeble 3800 simulator. The strain rate=1s^-1÷15.9s^-1 and strain degree ε=1.2. Before deformation, the research specimens were austenitized at TA = 1100 ÷ 1250 °C. Metallographic observations of the primary austenite grains were conducted with an optical microscope, while the structure of dynamically recrystallized austenite, inherited by martensite, was examined by EBSD technique using a scanning electron microscope. Based on the analysis of investigation results, it was found that the size of dynamically recrystallized austenite grains in HSLA steel were clearly affected by hot compression parameters. In contrast, no significant impact of austenitising temperature on their size was found.

Climate warming is expected to have pronounced effects on Arctic and Subarctic ecosystems, especially regions underlain by discontinuous and relatively warm permafrost. The main goal of this research is to evaluate the vulnerability and dynamics of permafrost under climate warming across the various ecotypes in respect of ecosystem stability, socioeconomic impact, and for better understanding possible future environmental changes. We suggested the new version of the spatially distributed permafrost dynamics model (GIPL2-MPI), which is developed in the Geophysical Institute, University of Alaska Fairbanks. This model is based on the ecosystem approach to simulate the permafrost dynamics, which we are discussing in this paper. We combined ground-based observations and numerical freeze/thaw modeling using climate-ecosystem-permafrost interactions to understand the physical processes and mechanisms controlling permafrost physical state. We predict the changes in permafrost conditions using output from two GCMs (NCAR-CCSM4 and GFDL-CM3) and Five-Model Average Ensemble for the RCP-4.5 and RCP-8.5 scaled down to 1 by 1 km spatial resolution (https://uaf-snap.org/) across entire Alaska. Our result shows that by the end of the current century widespread near-surface permafrost degradation could begin everywhere in Alaska southward of the Brooks Range as well as across some spots at the North Slope Alaska.

Fungal infection of grape berries (Vitis vinifera) by Botrytis cinerea frequently coincides with harvest, impacting both the yield and quality of grape and wine products. A rapid and non-destructive method for identifying B. cinerea infection in grapes at an early stage prior to harvest is critical to manage loss. In this study, zeolitic imidazolate framework-8 (ZIF-8) crystal was applied as an absorbent material for volatile extraction from B. cinerea-infected and healthy grapes in a vineyard followed by thermal desorption gas chromatography-mass spectrometry. The performance of ZIF-8 to absorb and trap targeted volatiles was evaluated with a standard solution of compounds and with a whole bunch of grapes enclosed in a glass container to maintain standard sampling conditions. Results from sampling methods were then correlated to B. cinerea infection in grapes as measured and determined by Genus specific antigen quantification. Trace levels of targeted compounds reported as markers of grape B. cinerea infection were successfully detected with in-field sampling. Peak area counts for volatiles 3-octanone, 1-octen-3-one, 3-octanol, and 1-octen-3-ol extracted using ZIF-8 were significantly higher than values achieved using Tenax®-TA from field testing and demonstrated good correlation with B. cinerea infection severities determined by B. cinerea antigen detection.

This scholarly article introduces the "Change Through Play: Rethinking Masculinity" program, a potential intervention designed to address gun violence in the United States by targeting its societal roots, particularly through the lens of gender socialization. The program focuses on transforming children’s, particularly young boys', perceptions of masculinity away from gun violence by influencing the types of toys they play with. By promoting non-violent play, the initiative aims to foster a future generation less inclined to engage in gun violence. This community-interactive and educational approach emphasizes the importance of evidence-based interventions that respect community values and cultural dynamics. The program employs a mixed-methods approach, combining qualitative and quantitative research to evaluate its effectiveness. The program highlights the necessity of sustained, collective action to transform the entrenched practices and beliefs that perpetuate violence, ultimately striving for a society that prioritizes peace, justice, and safety.

In the present article, the application of an artificial neural network (ANN) model is studied, whose function is the development of plastic instability maps of a medium carbon microalloyed steel during the hot forging process. And, secondly, we proceed to create another neural network capable of providing the recrystallized grain size in the steady state phase resulting from the deformation by hot forging, thus creating a methodology that can be applied to different types of processes and materials. In order to achieve this objective, we start from the experimental data of a medium carbon microalloy steel, obtained by hot compression tests, for strain rates that vary between 10-4 and 3 s-1 and in a range of temperatures between 900 oC and 1150 oC. These experimental data will be used to train the neural network that is intended to be created in this work. Once trained, it will be verified if the results of the test correspond to the experimental data and the fluency curves will be obtained. Finally, the processing maps will be developed applying the Dynamic Materials Model (DMM), according to which the safe domains to forge the material and the plastic instability domains are delineated, to be avoided during the forging process. The maps obtained by means of RNA will be compared with the experimental ones and it will be possible to verify that the optimal regions of forging in the maps obtained by RNA coincide with those obtained by means of experimental data. In addition, a study of the influence of the microstructure on the behavior of steel during hot forming will be carried out, since the experimental tests are carried out at austenitizing temperature, so the microstructure is different in each test.

Background. The Stanford Health Assessment Questionnaire-Disability Index (HAQ) is widely used to measure functional ability in persons with Rheumatoid Arthritis (RA). The instrument was developed with limited involvement from persons with RA, and their perception of the instrument has not been studied in depth. The aim of this study was to explore how persons with RA experience the use of the HAQ in care. Methods. Forty persons with RA were purposefully recruited to participate in semi-structured interviews. The interviews were then analyzed qualitatively using thematic analysis. Results. The participants questioned the relevance of the HAQ but nevertheless experienced that the instrument had a profound effect on their understanding of health and how care is delivered. The analysis resulted in three themes: Problems with individual items, meaning of the summative score, and effects on care and health perceptions. Conclusions. To make the HAQ relevant to persons with RA, it needs to be revised or to include an option to select items most meaningful to the respondent. To ensure relevance, the HAQ update should preferably be co-created by researchers, clinicians and persons with RA.

Extreme climates such as droughts and hot extremes, may result in marked damage to crop yields and threaten regional and global food security. Maize is a major grain crop in Liaoning Province, severely affected by drought and hot events. The objective of this study is to advance an approach to estimate the risk of crop yield reduction under the compound dry-hot events (CDHE) in Liaoning Province. Results show that the ratio of stations experiencing compound dry-hot events during the twelfth leaf and maturity stage tended to increase on the time scale. On a spatial scale, the frequency of compound dry-hot events in central Liaoning Province was relatively low during the whole and various reproductive periods of maize. In addition to the twelfth leaf, western Liaoning Province is prone to compound dry-hot events. The high-risk area for the occurrence of the compound dry-hot events in maize is Chaoyang City, located in the western part of Liaoning Province, and the cities in the low-risk area account for about 64.3% of the total number of cities in Liaoning Province, mainly in the central and northern parts of Liaoning Province. Generally, this study emphasizes focusing on the impacts of compound dry-hot events on agricultural production and provides an index to assess the risk of compound dry-hot events on maize production.

. Background/Objectives: Crohn's disease is a chronic and debilitating intestinal disorder that alternates between remission and active flare-ups, often leading to hospitalization. Social support is known to enhance adaptation to the disease and modulate stress perception in patients, while stress may exacerbate symptoms. The aim of this study was to examine the roles of perceived stress and social support in Crohn's disease and their impact on the frequency of flare-ups. Methods: A cross-sectional observational study was conducted, assessing stress and social support in a cohort of 91 patients with Crohn's disease during flare-up and remission phases. The Perceived Stress Scale (PSS-14) and a Social Support Questionnaire were utilized for evaluation. We examined the relationship between stress and social support in Crohn's disease. The interaction between the variables studied was also studied, considering the stage of the disease. Finally, we realized analysis of the influence of these two variables on the development of flares in Crohn's disease. Results: The study revealed that patients experience higher stress levels during flare-ups and that these levels are amplified by a lack of social support. A significant relationship was identified between the levels of social support and the occurrence of flare-ups, indicating that better social support is associated with fewer flare-ups.. Conclusions: Patients with Crohn's disease in the flare-up phase are subject to considerable stress. Deficit in social support is linked to an increase in stress levels. The interplay of social support and stress plays a critical role in the development of flare-ups.

Occupational accidents, despite continuous safety updates, are still a scourge in the occupational and forensic spheres, constituting, among other things, the subject of a large share of litigation. Demographic data can help to understand the areas where the application of health surveillance is lacking. This meta-analysis sets out to analyze data from studies on accidents at work, focusing on the correlation between the areas in which accidents occur and whether or not personal safety equipment is used, about the different regulations in force. For the selection of the data, a systematic review was carried out according to the PRISMA guidelines, with the primary objective of identifying the trend of occupational accidents in specific geographical areas, which differ in terms of the attention paid to preventive aspects. The data we highlighted showed, regarding the type of accident, substantial differences between low-income countries and industrialized countries (stratified according to the Human Development Index) and, an overall indifference as to whether or not individual safety devices were used, revealing that, despite the continuous normative evolution in the field of safety at work, even today, the investigative data on the actual application of the regulations, during accidents at work, is underestimated and little researched.

This paper focused on the finite element analysis of structural system in extreme loading condition. Two different stud shape and thicknesses were analyzed under blast. The stud thickness such as 1.19 mm and 1.5 mm were modelled and analyzed using ABAQUS 6.14. FEM is a tool which predicts the engineering physics of the real structure. To validate the finite element modelling performed by authors, a reference work published by earlier researchers on cold-formed steel stud wall is considered and examined in the present study. The novelty of this study was web corrugation and influence of flange width on stud. The models mimic like an air bag in a car to delay the pressure timing inside the stud wall. The mass of explosive used as 1.56 kg at a standard scaled distance. Time versus displacement was captured out at four locations in the stud wall. One of the objectives is to develop mathematical model to validate the deformation of stud under blast loading. Two mathematical models were validated using Artificial Neural Network (ANN). The results captured in ANN model was error histogram, regression plot, best performance fit and training data. The models were capable of resisting the moderate blast load. The response surface methodology (RSM) was employed to evaluate model performance Regression equations are useful for predicting future trends and outcomes, which is crucial for planning and decision-making. The primary goal of this work is to evaluate cold-formed steel stud walls with varying stud sizes under blast loading using finite element analysis and validated by ANN and RSM.

Background: The concept of Quality of Work Life (QWL) has been built multidimensionally through social reproduction; it is impacted by the perceptions of each individual and by the relationship between workers and the work environment. Objective: to analyze the Work Process and QWL of assisting nurses in public health. Methods: Research in a critical paradigm, descriptive, exploratory with a qualitative approach. The population corresponds to Nurses who work in care work. Semi-structured guiding questions were applied and were analyzed with content analysis. Results: seven participants declared female; all Chilean; seven are young adults; six singles; only one has children, and one has a person dependent on her care; six are heads of household, and five receive help with housework. All have a nursing degree, five have a diploma, but none have a postgraduate. Work Process has three subcategories: work object, instrument, organization, and work conditions; the QWL category has six subcategories: definition and perception of QWL, QWL potentiating factors, QWL exhausting factors, QWL improvement strategies, the emotional burden associated with QWL, and Health problems. Conclusions: In this way, the lifestyle built by the assistance in the health area has repercussions on the quality of life and health in general.

Remote work as a new working pattern is considered of high importance in determining the competitiveness of the institutions that adopt this form of work. This trend toward remote working has benefited workers greatly in terms of flexibility and work-life balance and has had unanticipatedly positive effects on sustainability. The issue has grown in importance considering recent development of digitalization and high concern of countries to achieve the sustainable goals. This study attempts to examine the effect of three explanatory variables: remote work, institutional efficiency, and work management on the competitiveness of finance institutions in Saudi Arabia. To collect the primary data, a survey was conducted on a stratified random sample that comprised 1270 respondents. The sample covers the three finance sector segments: banks, insurance, and finance companies. Correlation analyses, one-sample t-tests, and multi-regression analyses are applied to analyze the data. The results of the study showed that there is a positive significant relationship between the three explanatory variables of the study and institutional competitiveness. Besides, the regression model revealed that the two explanatory variables; remote work and institution efficiency are statistically significant at 95% confidence intervals, while work management is not statistically significant. The study recommends promoting remote work to increase the finance institution's competitiveness by restructuring the work policies, designing work strategies, and introducing a new management system compatible with remote work.

The CMT (Cold Metal Transfer) arc welding process is a convenient instrument for the assembly of thin sheets [1], [2]. More particularly, it permits the decrease of the amount of heat transferred to the parts to-be assembled, thus reducing their subsequent deformations. The present work aims at simulating the CMT welding of thin stainless-steel sheets in order to develop an approach that allows the prediction of temperature fields, as well as final deformations induced by the welding process. For that purpose, instrumented tests and numerical simulations were set aiming at comparing the experiments with simulations. Butt-welding of stainless-steel sheets was considered, with a thickness ranging from 1 to 1.2 mm. The weld seam samples were observed in order to set an equivalent heat source for each configuration. Moreover, the electric current and voltage were surveyed, and temperature measurements were performed using K-type thermocouples. In addition, displacement measurements were obtained using the DIC (Digital Image Correlation) technique. Thermomechanical simulations were then carried out using an equivalent heat source approach, considering the phase changes of elements, i.e. the transitions from solid to liquid and from liquid to solid. These simulations also consider the actual geometry of seams induced by addition of a filler material.

Landraces are considered a crucial component of biodiversity conservation, serving as a reservoir of genetic diversity. Consequently, the collection, cultivation and detailed characterization of such landraces constitute an inherent aspect of the world’s natural resource heritage. This effort holds promise for the development of elite varieties capable of thriving amidst continuous global climate fluctuations. In this context, we conducted a comprehensive assessment of the main agronomic attributes, physico-chemical properties, and functional quality traits of the major hot pepper landraces adapted to diverse climatic conditions in Tunisia. These landraces include ‘Dhirat’, ‘Semmane’, ‘Beldi’, ‘Nabeul’, ‘Jerid’, ‘Mahdia’, ‘Cayenne’, ‘Kairouan’ and ‘Baklouti’. Most of the pepper landraces exhibited satisfactory yields, ranging from 1163.25 to 1841.67 g plant-1 in ‘Jerid’ and ‘Kairouan’, respectively, indicating robust productivity, especially under prevailing climatic changes and high temperatures. Landraces such as ‘Baklouti’, ‘Beldi’, ‘Nabeul’, ‘Semmane’, ‘Kairouan’ and ‘Mahdia’ appear suitable for both fresh consumption and processing, owing to their favorable average fruit weight and soluble solids content. Functional quality and the levels of antioxidants, as well as radical scavenging activity, emerged as key discriminating factors among pepper landraces. Irrespective of genotype, capsaicin and dihydrocapsaicin constituted the major capsaicinoids, accounting for at least 87% of the total. Total capsaicinoids ranged from 1.81 µg g−1 to 193.71 µg g−1, with ‘Baklouti’ and ‘Jerid’ identified as the most pungent landraces. Total carotenoids ranged from 45.94 µg g−1 to 174.52 µg g−1 with ‘Semmane and ‘Jerid’ exhibiting the highest levels. Considerable variation was observed in β-carotene content, spanning from 3% to 24% of the total carotenoids. α-Tocopherol content ranged from 19.03 µg g-1 fw in ‘Kair-ouan’ to 30.93 µg g-1 fw in ‘Beldi’, exerting a notable influence on the overall tocopherol content. Conversely, the other isomers were detected at very low concentrations. The total vitamin C content ranged from 132 mg 100g-1 fw in ‘Mahdia’ to 200 mg 100 g-1 fw in ‘Nabeul’, indicating relatively low genetic variability. However, large variability was detected in total phenolics content, ranging from 168.58 mg GAE kg-1 fw in ‘Beldi ‘to 302.98 mg GAE kg-1 fw in ‘Cayenne’. Among the pepper landraces tested, ‘Cayenne’ achieved the highest value of radical scavenging activity in both hydrophilic and lipophilic fractions (RSAHF and RSALF), with variations rang-ing from 59% to 120% for RSAHF and from 4% to 64% for RSALF. This study aims to: 1) preserve and enhance the value of local genetic resources, 2) identify desiderable traits for incorporation into breeding programs, and 3) develop high-quality, high-yielding cultivars capable of with-standing climate variations.

This study investigates the effect of perceived discrimination on the mental health of Afghan refugees, and secondly, tests the distress moderating effects of pre-migration traumatic experiences and post-resettlement adjustment factors. In a cross-sectional design, 259 Afghans completed surveys assessing perceived discrimination and a number of other factors using scales developed through inductive techniques. Multivariate analyses consisted of a series of hierarchical regressions testing the effect of perceived discrimination on distress, followed by a sequential analysis of moderator variables. Perceived discrimination was significantly associated with higher distress, and this relationship was stronger among those with a strong intra-ethnic identity, high civic engagement, and high pre-resettlement traumatic experiences. Discrimination is a significant source of stress for Afghan refugees, which may exacerbate stresses associated with other post-migration stressors. Future research is needed to tailor interventions that can help mitigate the stress associated with discrimination among this highly vulnerable group.

3D printing is a non-traditional additive manufacturing process. It is different from the traditional subtractive manufacturing process. It offers exceptional rapid prototyping capabilities and results that traditional subtractive manufacturing methods cannot attain, especially in applications involving curved or intricately shaped components. Despite its advantages, metal 3D printing will face porosity, warpage, and surface roughness issues. These issues will affect the future practical application of the parts indirectly, for example, the structural strength and the parts assembly ca-pability. Therefore, this study compares the qualities of the warpage, weight, and surface rough-ness after milling and grinding processes under the same materials (316L stainless steel) between general rolled steel and 3D additive steel. Experimental results show that 3D printing parts are approximately 13% to 14% lighter than the general rolled steel. The surface roughness performance of 3D printing steel is better than general rolled steel under the same material after milling or grinding processing. The hardness of the 3D printing steel is better than that of the gen-eral rolled steel. The research verifies that 3D additive manufacturing can use surface processing to optimize surface performance and achieve the functions of lightness and hardness.

Healthcare personnel must face two problems of growing importance: violence in the workplace and the loss of work ability due to ageing of the workforce. Studying the relationship between these two phenomena can help to prepare effective prevention measures. In a public health company, we asked nurses to self-assess their work ability using the Work Ability Index (WAI) and we analysed the relationship between this indicator and the violence experienced in the previous and following years. 321 out of 344 nurses (99.3%) participated. In a logistic regression model, the WAI score was a significant protective factor for violence experienced in the previous year (OR=0.94 CI95%=0.90; 0.98 p<0.01) and in the following year (OR=0.88 CI95%=0.84; 0.92 p<0.01). In a hierarchical logistic regression model, social support acted as a protective factor (OR = 0.87 CI95% = 0.79; 0.95 for violence experienced in the previous year), while occupational stress was a significant determinant of the risk of aggression (OR=3.65 CI95%=1.90; 7.03 in the previous year, OR=3.54 CI95%=1.801; 6.947 in the following year). The difficulties that nurses encounter in carrying out their growing work demands in an environment that is not promptly adapted to their changing physical and mental conditions can lead to an increased risk of violence. Prevention of workplace violence should include organizational and ergonomic measures that reduce stress and increase staff support and work ability.

Rhododendron chrysanthum Pall., live in Changbai Mountain being exposed to chilling temperature, high light intensities and water scarcity condition. To adapt to the harsh environment, the cold resistance mechanisms of R. chrysanthum have been successfully evolved in the long-term adaptive process. In our present work, the methods of proteomics combined with physiological and biochemical analyses were used to investigate the effects of cold stress on the photosynthesis and antioxidant system of Rhododendron chrysanthum Pall. and the molecular mechanisms involved in cold resistance of plants. A total of 153 photosynthesis related proteins were identified in present work, of which 7 proteins including Rubisco large subunit (rbcL) were up-regulated in experiment group (EG) compared with control group (CG). Simultaneously, four chlorophyll fluorescence parameters were measured in present study. The results showed that the maximum photochemical efficiency of photosystem II (Fv/Fm), actual quantum yield of PSII (Y(II)) and photochemical quenching (qP) were significantly higher in EG, whereas the non-photochemical quenching (NPQ) was notably decreased. Cold stress could lead to a significant reduction in electron transport rate (ETR) accompanied with an increase in excitation pressure (1-qP). The abundance of PetE which involved in the plants photosynthetic electron transfer was also significantly influenced by cold stress. Moreover, the up-regulated expressions and higher levels of enzymatic activities of Glutathione peroxidase (GPX) and Ascorbate peroxidases (APXs) were detected in EG. All these changes which can help plants to survive in low temperature are considered as the crucial parts of cold tolerance mechanisms. These results revealed that photosynthesis and redox adjustment play significant roles in the defense of cold-induced damage.

In this study, we evaluated the cold drawing workability of two kinds of modified 9Cr-2W steel containing different contents of boron and nitrogen, depending on the temperature and time of normalizing and tempering treatments. Using ring compression tests at room temperature, the effect of intermediate heat treatment condition on workability was investigated. It was found that the prior austenite grain size can be changed by the austenite transformation, and the grain size increases with increasing temperature during normalizing heat treatment. Alloy B and Alloy N showed different patterns after normalizing heat treatment. Alloy N had higher stress than Alloy B, and the reduction in alloy N increased, while the reduction in alloy B decreased. Alloy B showed a larger number of initially formed cracks and a larger average crack length than Alloy N. Crack length and number increased proportionally in Alloy B as the stress increased. Alloy B had lower crack resistance than Alloy N due to boron segregation.

Longitudinal cutting is a most common process in steel structure manufacturing, and the man-hours of the process provide an important basis for enterprises to generate production schedules.However, currently the man-hours in factories are mainly estimated by experts, and the accuracy of this method is relatively low.In this study,we propose a system that predicts man-hours with history data in the manufacturing process and that can be applied in practical structural steel fabrication.The system addresses the data inconsistency problem by one-hot encoding and data normalization techniques,Pearson correlation coefficient for feature selection,and the Random Forest Regression(RFR) for prediction.Compared with the other three Machine Learning(ML) algorithms, the Random Forest algorithm has the best performance.The results demonstrate that the proposed system outperforms the conventional approach and has better forecast accuracy, so that it is suitable for man-hours prediction.

In the steel industries, workers are exposed to heat and ambient thermal stresses on a daily basis, leading to discomfort and limited performance. In this study, the main purpose is to investigate the effect of climate heat stress on the rate of accidents in the workplace for workers for 5 consecutive years. The data of this study were received without any sampling through the HSE Center for Steel Industry and meteorological data from 2015 to 2019 from Isfahan Meteorological station. The daily number of casualties among workers in the steel industry during 2015-2019 by adjusting seasonal patterns, months, effects of the day of the week and other meteorological factors on the average daily temperature using the studied model has a decreasing effect. Eviews software (version 8) was used to model and investigate the relationship between events and meteorological variables. The mean temperature was at least 40.2-2 and at most 70.34 ° C, respectively. In the time-series study for the main model, the number of accidents shows a direct relationship with the average temperature and wind speed. Climatic indices of humidity and rainfall have the least impact on accidents compared to temperature and wind speed. A strong correlation was shown between the increase in average ambient temperature and the rate of accidents over the past 5 years. Given the fundamental differences in studies of environmental exposure and wind speed over heat stress, further analysis in workers should be considered.

Work context is essential to understand in relation to handle the stress at work that ultimately creates a feeling of satisfaction or dissatisfaction among health professionals. The current study was conducted to investigate the relationship of work context and work stress among sonographers (n=153) in Riyadh, Saudi Arabia. Additionally, the study provided a gender-based comparison of both variables among sonographers. Work context was measured by administering subscale of work context derived from Work Design Questionnaire. Whereas, work stress was measured by Job Stress Scale. In addition, relationship of lifestyle was explored with work context and work stress. Data was collected through survey research forms. Results revealed the significant relationship of work context and work stress (r=.251, p=.002). Among lifestyle variables, perceived good health (r= .214, p=.008) and sleep (r=.242. p=.003) were found positively related with satisfaction toward work. Whereas, the strong positive correlation was found between work context and frequency of physical activity (r=.255, p=.005). No significant difference was found among male and female sonographers. The findings of this study contributed to evaluating the working condition of sonographers in relation to work stress. Effective strategies for better working settings as well as strategies for achieving satisfaction in work will be discussed to enhance the performance of sonographers.

In order to achieve the elimination of the negative impacts of transport on road safety, the European Union is taking various measures resulting from its commitment to improve road safety. One of the instruments for achieving the objectives set is social legislation for the work of drivers in road freight and passenger transport. In line with the objective of improving the quality of working conditions for road transport drivers and road safety, the European Union applies Regulation (EC) No 561/2006 on the harmonisation of certain social legislation relating to road transport, which lays down rules on driving times, breaks and rest periods for drivers operating in road freight and passenger transport. The main objective of the paper is to assess the impact of social legislation on road transport safety by means of real research and to identify the factors influencing the violation of the legislation depending on the type of transports carried out in domestic or international road freight transport.

Insecurity, corruption, and rising unemployment have resulted in a mass exodus of young adult Afghans seeking asylum in western nations. This has depleted Afghanistan of generations of young people which are critical to rebuild the country. This study aimed to examine the characteristics of young adult Afghans with no immediate intentions of seeking international asylum; that is, individuals who intend to stay in Afghanistan. In a cross-sectional study conducted in Kabul, we surveyed 232 young adults between 18 and 35 years of age. Surveys included measures assessing standard socio-demographic and -economic factors, as well as health and psychological factors. Univariate logistic regression analyses suggest that participants with an intent to stay in Afghanistan are more likely to be financially stable, possess higher health-related quality of life, lower psychological distress, and higher levels of hope and optimism, as well as higher resilience. When controlling for all other variables in the model, only hope, optimism, and higher resilience remained as significant correlates of intending to stay. Our findings suggest that young people who intend to stay in their country look forward to a better future, which provides strong evidence for the need to strengthen the social contract by fostering resilience, hope and optimism in war-affected communities, in order to prevent a generation of talented young people from seeking asylum in western nations.

While cycling presents environmental benefits and promotes a healthy lifestyle, the risks associated with overtaking maneuvers by motorized vehicles pose significant hindrances for many potential cyclists. Large-scale analysis of overtaking maneuvers could inform traffic researches and city planners on how to reduce these risks by better understanding these maneuvers. Drawing from the fields of sensor-based cycling research and of LiDAR-based traffic data sets, this paper provides a step towards addressing these safety concerns by introducing the Salzburg Bicycle 3d (SaBi3d) data set, consisting of LiDAR point clouds capturing car-to-bicycle overtaking maneuvers. The data set, collected using a LiDAR-equipped bicycle, facilitates detailed analysis of a large quantity of overtaking maneuvers without the need for manual annotation through enabling automatic labeling by a neural network. Additionally, a benchmark result for 3d object detection using a competitive neural network is provided as a baseline for future research. The SaBi3d data set is structured identically to the nuScenes data set, and therefore offers compatibility with numerous existing object detection systems. This work provides valuable resources for future researchers to better understand cycling infrastructure and mitigate risks, thus promoting cycling as a viable mode of transportation.

Porous α-Al2O3 ceramics is a highly demanded material for multitude applications such as filters, substrates, biomedicine materials, etc. Despite the availability of the raw materials, a challenge of their technology is in a high energy budget caused by the sintering above 1500 °C. For a cold sintering processing (CSP) of ceramics, the lowering of α-Al2O3 sintering temperature is one of the most urgent challenges at the background of its rapid development. The current paper for the first time demonstrates the solution of the mentioned problem by the CSP of α-alumina ceramics in a presence of pure water as a transient liquid. The manufactured materials were examined by XRD analysis; the evolution of their microstructures during the CSP was revealed by SEM, and the porosity evaluated by the Archimedes method. The ceramics with an open porosity up to 36 % was produced at 380-450 °C, 220 MPa in 30 min. An increase in the pressure was found to impede α-Al2O3 formation from γ-AlOOH. The development of the microstructure was discussed within the frameworks of the dissolution-precipitation model and the homogenous nucleation. The results of the SEM study pointed to the coalescence of γ-AlOOH grains during the CSP.

This paper presents the deformation of the joined sheet after the clinch-riveting process. The DX51D steel sheet with zinc coating was used. The samples to be joined with clinch riveting technology had a thickness of 1±0.05 mm and 1.5±0.1 mm. The sheet deformation was measured before and after the joining process. The rivet was pressed in the sheets with the same dimension between the rivet axis and three sheet edges: 20, 30 and 40 mm. For fixed segments of the die, from the rivet side close to the rivet, the sheet deformation was greater than that of the area with movable segments. The movement of die sliding element caused more sheet material to flow in the space between the fixed part of the die and movable segments. Hence, the sheet deformation in these places was smaller than for the die fixed element – sheet material was less compressed. For sheets thickness 1.5 mm and width 20 mm, the bulk of the sheet was observed. For a sheets width of 20 mm, it was observed that the deformation of the upper and lower sheets in the area of the rivet is greater than for sheets width of 30 or 40 mm.

A proposed low-temperature forging method aims to enhance stainless steel bearings by creating a martensitic subsurface layer, significantly boosting bearing fatigue life due to increased surface hardness. This technique induces beneficial residual stresses, particularly in axial bearings, streamlining their construction and improving machine elements. Challenges persist, especially with radial bearings, but simplicity in axial bearing forging promotes compact, resource-efficient facility construction. Future research will focus on applying this technique to axial bearing washers, potentially replicating success in other bearing components. Despite the energy ex-penditure for cooling during forging, the substantial increase in bearing fatigue life offsets this, enhancing overall longevity and reliability of critical machine components. Integration of this forging technique into bearing fabrication appears seamless, offering a promising trade-off be-tween energy use and enhanced performance.

The importance of conflict analysis and safety considerations during work zone intervals at signalized intersections cannot be overstated, as these periods pose unique challenges and safety risks for both motorists and pedestrians. Work zones introduce temporary changes to traffic patterns, lane configurations, and signal timings, which can disrupt the flow of traffic and increase the likelihood of conflicts between vehicles and pedestrians. By conducting comprehensive conflict analysis, it is possible to identify potential conflict points, such as merging areas, pedestrian crossings, and lane transitions, and implement targeted safety measures to mitigate risks. Additionally, considering safety considerations during work zone intervals is paramount to safeguarding the well-being of road users and minimizing the occurrence of conflicts or collisions. Measures such as enhanced signage, temporary traffic control devices, and increased enforcement efforts can help promote compliance with traffic regulations and ensure the safe passage of vehicles and pedestrians through work zones. This study investigates the dynamics of traffic behavior and safety implications within work zones at signalized intersections, aiming to address key challenges and enhance intersection management strategies. Through comprehensive analysis, varying frequencies of Vehicle-to-Vehicle (V2V) conflicts were observed across different movement directions, with significant occurrences identified in specific phases of the traffic signal cycle. Specifically, 69 V2V conflicts in phase #1, 181 in phase #2, 31 in phase #3, 207 in phase #4, 1 in phase #5, 274 in phase #6, 93 in phase #7, and 186 in phase #8 were recorded. Furthermore, the examination of Vehicle-to-Pedestrian (V2P) conflicts underscored the importance of prioritizing pedestrian safety, with notable occurrences observed in phases associated with pedestrian crossing movements. Meanwhile, despite the closure of left-turn movements, instances of red light running persisted, with 69 red light running events in phase #1, 181 in phase #2, 31 in phase #3, 207 in phase #4, 1 in phase #5, 274 in phase #6, 93 in phase #7, and 186 in phase #8.To mitigate these safety concerns during work zone intervals, proactive measures are essential. Strategies include improving communication through clear signage and advanced warning systems, enhancing enforcement efforts with red light cameras and increased police presence, and investing in infrastructure improvements such as temporary pedestrian facilities. Integration of real-time data from sensors, particularly LiDAR technology, offers significant advantages in detecting conflicts and red light runners during work zone intervals. LiDAR's precise, real-time data on vehicle and pedestrian movements, combined with its 360-degree coverage and high spatial resolution, facilitates accurate detection and tracking of potential conflict scenarios, contributing to enhanced intersection safety and traffic management efficiency. This study endeavored to conduct a traffic safety analysis during work zone intervals at a signalized intersection in Baltimore City, known for its high rate of traffic crashes, utilizing LiDAR sensor technology.

Creativity in virtual work environments and its influence on emotional exhaustion is a relationship with inconclusive results. Furthermore, autonomy, when it loses its original purpose of acting as a job resource, takes on an ambiguous role that needs further research. Objective: To analyze the relationship between creativity and emotional exhaustion, along with the role assumed by work autonomy in this link, in an online work context. Methodology: The sample is formed by 448 employees with university studies. The statistical analysis is done through a simple moderation process. Results: Creativity and work autonomy mitigate emotional exhaustion. Control over work surely reduces the impact of work related stressors, and this safety climate promotes adaptive and original responses that improve employees' emotional health. However, when creative demands coincide with an autonomy that extends working hours, instead of establishing limits, this supposed benefit becomes a demand that prevents employees from disconnecting until emotionally exhausting them. Conclusion: A virtual work environment is an ideal habitat for creativity and self-management to improve employees' emotional health, as long as work autonomy acts as a resource.

Breast cancer (BC) is the most common invasive neoplasm and affects many women of working age. The return to work (RTW) of female survivors (BCSs) is associated with a better quality of life and longer survival. A tailored intervention to promote RTW was launched in 2022. A year later, the women were contacted to find out if RTW had occurred regularly and what their health conditions were compared to baseline. BCSs reported excessive fatigue, poor sleep quality, anxiety, depression and reduced work ability; these parameters had not improved significantly compared to baseline. Thematic analysis of the interviews confirmed the presence of personal, company and societal factors that could hinder or favor RTW. The interviews demonstrated that, even in an economically developed country that has provided numerous benefits for BCSs, protection is not always effective. Personalized intervention seems necessary to complete the process of reintegrating BCSs into their future working careers.

In steel structures, oblique thin steel plates serve as panel zones in structures spanning large spaces (e.g., warehouses and gymnasiums). Considerable research has been conducted on the shear buckling of panels due to seismic loads acting on a structure. Conversely, under snow or wind loads, the panel zone may experience compressive and tensile stresses simultaneously from two directions. Considering the economic preference for thin steel plates, evaluating the elastic critical local buckling stresses in the panel zone under biaxial normal stress may provide essential information to structural engineers. In this study, an elastic buckling analysis based on the energy method is performed to clarify the impact of panel geometry and boundary conditions on the elastic local buckling stresses of oblique panel zones. As confirmed, the buckling stresses derived from the energy method could simulate the local buckling stresses with accuracy comparable to that of finite element analysis, and an engineer-friendly design formula was proposed. Finally, we determined the correlation of the buckling stresses under biaxial stresses and presented a method for evaluating this correlation. Engineers can utilize the provided design equations to more efficiently and accurately calculate buckling loads, facilitating safer and more economical design of structures with oblique plates.

In graduate programs such as social work, field education is the signature pedagogy of education. As such, student placement with an appropriate field education agency is critical to ensure academic success and career readiness. A variety of Learning Management System (LMS) and Integrated Planning and Advising Service (IPAS) technologies have been developed to fully integrate technology into the educational system and streamline and improve the learning experience for students, educators, and administrators. Few (if any) of the existing solutions have capabilities to match students with field educators on the basis of an individual student’s completed coursework and area of specialization, as well as field educator needs and opportunities. This paper describes our experience developing a custom LMS/IPAS system—the School of Social Work information System (SSWiS)—that was designed specifically for student learning, faculty advising, and academic administration within our social work graduate program. We present the challenges that motivated the design of the SSWiS before describing the architecture and functionality of our solution. We then discuss our preliminary evaluation results. We conclude with a discussion of the benefits and limitations of our system in the context of today’s technical needs in graduate education in social work and other fields.

Grand challenges represent wicked problems that affect many people globally. To overcome grand challenges and sustain our existence as human beings, issues have become increasingly central, and in recent years have led to an increase in research and literature on grand challenges affecting both international business areas and multinational enterprises. The aim of this study is to assess the status of literature in all areas connected to multinational corporations and grand challenges, which are global issues with significant implications. From 2013 to 2023, the WoS database was used to investigate eight search terms from literature, and bibliometric and thematic analyses were carried out based on the principles of systematic literature analysis. The most focused areas of the research are performance, multinational enterprises, foreign direct investment, management, firms’ innovation, knowledge, international business, and impact. Asian, African, European, and other countries may emerge together in different clusters depending on whether the major challenges they are struggling with are similar or identical. the terms of grand challenges and innovation (open and social), technology transfer, R&D internalization, digital transformation or technology and artificial intelligence in the literature of multinational enterprises indicates that these themes are used as a tool to solve grand challenges.

The electric vehicle (EV) industry challenges battery joining technologies by requiring higher energy density both by mass and volume. Improving the energy density via new battery chemistry would be the holy grail but is seriously hindered and progresses slowly. In the meantime, alternative ways, such as implementing more efficient cell packaging by minimizing the electrical resistance of joints are of primary focus. In this paper we discuss the challenges associated with the electrical characterisation of laser soldered joints in general, and the minimization of their resistive losses, in particular. In order to assess the impact of the joint resistance on the overall resistance of the sample, the alteration in resistance was monitored as a function of voltage probe distance and modelled by finite element simulation. The experimental measurements showed two different regimes: one far from of the joint area and another in its vicinity and within the joints cross section. The presented results confirm the importance of the thickness of the filler material, the effective and the total soldered area, and the area and the position of the voids within the total soldered area in determining the electrical resistance of joints.

The impact of systemic vascular resistance (SVR) in hypertrophic (HCM) and amyloid cardio-myopathies has been seldom investigated. We studied pressure-strain loop derived myocardial work (MW) indices and SVR in patients with either sarcomere HCM or wild type transthyretin cardiac amyloidosis (ATTR), presented with heart failure and preserved left ventricular ejection fraction (HFpEF) at the outpatient cardiology units at Messina and Catania University Hospitals (Italy). Patients were in sinus rhythm and needed to have good transthoracic ultrasound imaging quality to undergo transthoracic strain-echocardiography. Other than conventional parameters, SVR and GWI (global work index) were measured. Based on cross-tabulation (a way to assess the ventricular-arterial coupling), the patients were then classified in 4 classes according to the cut-off values suggested by previous studies of 1,440 dyne/s/cm-5 for SVR (Stefadouros et al., 1973) and 1576 mm Hg% for GWI (Olsen et al., 2022). Sixty patients, 30 in each group, aged 61±16 years, 78% males, were studied. HCM were younger than ATTR patients and in a better clinical status (23% HCM vs 77% ATTR were NYHA class 3, p<0.001). Overall, 51 patients (85%) showed high SVR, of whom 21 were HCM (70%) and 30 ATTR (100%) (p<0.005). Both, SVR and GWI were impaired (the poorest class C) in 43% HCM patients (with greater left ventricular concentric hypertrophy) vs 93% of ATTR patients (in advanced NYHA class) (p<0.001). In conclusion, assessing SVR and GWI in HFpEF patients with HCM or ATTR can help clinicians to interpret the pathophysiological and clinical features of such complex diseases.

Isothermal interrupted hot compression tests of 5754 aluminum were conducted on Gleeble-3500 thermo-mechanical simulator at temperature 350 °C and 450 °C, strain rate 0.1 s-1 and 1s−1. These tests simulated flat rolling to investigate how softening behaviors respond to controlled parameters, such as deformation temperature, strain rate and delay times. This data allowed the parameters for the hot rolling process to be optimized. The delay times during interrupted compression vary between 5s and 60s. The dynamic softening at each pass and metadynamic recrystallization at the intervals of deformation passes were analyzed in detail. 0.2% offset yield strength is applied to calculate the softening fraction undergoing metadynamic recrystallization. A kinetic model was developed to describe metadynamic recrystallization behaviors of the hot deformed 5754 aluminum alloy. Furthermore, the time constant for 50% recrystallization was expressed as functions related to the temperature and the strain rate. The experimental and calculated results were found to be in close agreement, which verified the developed model.

Bi1-xSbx crystal is one of the best n-type thermoelectric materials below 200 K, but its weak mechanical strength hinders practical applications for deep refrigeration. Herein, we adopted the mechanical enhancement method of hot extrusion to investigate the comprehensive mechanical and thermoelectric properties of Bi0.905Sb0.095. It revealed that reducing the grain size of the matrix and increasing the extrusion ratio can improve the gain size uniformity and mechanical properties. While the thermoelectric performance depends on the texture, grain size, and local composition. The extruded sample prepared by ingot with the high extrusion ratio of 9:1 generated a high texture degree of (001) plane and small grain sizes between ~4-40 mm, which resulted in the high bending strength of Bi1-xSbx ~130 Mpa and a high-power factor of ~ 68 μW·cm-1·K-2@173 K, as well as the relative high figure of merit of 0.25@173K. This work highlights the importance of the uniform distribution of the grain size and the compositions for Bi1-xSbx, as well as the required universal key parameter for the hot-extrusion method.

The commercial oxygen-free copper sheets were cold-rolled with reduction rates ranging from 20% to 87% reduction rate and annealed at 400, 500 and 600 °C. The microstructure and texture evolution during cold-rolling and annealing processes were studied using optical microscopy (OM), the scanning electron microscopy (SEM) and the electron back-scattered diffraction (EBSD). The results show that the deformation textures of {123} (S) , {112} (Copper) and {110} (Brass) were continuously enhanced with the increase of cold-rolling reduction. The orientations along the α-oriented fiber converged towards Brass and the orientation density of β fiber obviously increased when the rolling reduction exceeded 60%. The recrystallization texture was significantly affected by the cold-rolling reduction. After 60% cold-rolling reduction, Copper and S textures components gradually decreased and {011} recrystallization texture component formed with the increase of annealing temperature. After 87% cold-rolling reduction, a strong Cube texture formed and other textures were inhibited with the increase of annealing temperature. The strong Brass and S deformation texture was conducive to the formation of a strong Cube annealing texture. The density of annealing twin boundary decreased with the increase of annealing temperature, and more annealing twin boundaries formed in the oxygen-free copper sheets with the increase of cold rolling reduction.

The prevalence of diagnosed cases of autism has increased rapidly, which raise interest in studying the variables related to the well-being of these families. The purpose of this paper is to review recent literature on other variables related to family well-being such a parenting styles. We conducted a systematic review using PRISMA check list and bias assessment ESTROBE with the aim of analyzing if the concepts of autism, well-being and parenting style are related. We screened 753 references, 16 full text articles and abstracts were read. It was identified that authoritative parenting style, those based on warmth, establishing relationships and emotional bonding, and low expressed emotion were positively related to family well-being. On the other hand, authoritarian, permissive and overprotective styles, as well as critical, punishing and training-based were negatively associated with well-being and quality of family life.

It is shown that the gravitational mass-energy defect could be the main cause of Big Bang energy and triggering inflation in the newborn Universe.

Hot deformation at elevated temperature is essential to densify the particle reinforced Aluminum matrix composites (AMCs) and improve their performance. However, hot deformation behavior of the AMCs is sensitive to the variation of hot processing parameters. In this paper, optimal processing parameters of the dual-scale SiCp/A356 composites was determined to explore the control strategy of the microstructure. Hot compression tests were conducted at the temperature ranging from 460 to 520℃ under strain rates from 0.01 to 5 s−1. Constitutive equation and processing maps were presented to determine the hot processing parameters. Microstructure evolution of the dual-scale SiCp/A356 composites was analyzed. The strain rate of 0.62 ~ 5s-1 and deformation temperature of 495 ~ 518℃ is suitable for the hot processing. The number of DRX grains in the “safe” domains is larger and the dislocation density is lower compared to those of instability domains. DRX particles mainly occurred around SiC particles. The presence of SiC particles can promote effectively the DRX nucleation, which result in that the dynamic softening mechanism of the dual-scale SiCp/A356 composites is dominated DRX.

Gas flaring is a disposal process widely used in the oil extraction and processing industry. It consists in the burning of unwanted gas at the tip of a stack and due to its thermal characteristic and the thermal emission it is possible to observe and to quantify it from space. Spaceborne observations allows us to collect information across regions and hence to provide a base for estimation of emissions on global scale. We have successfully adapted the Visible Infrared Imaging Radiometer Suite (VIIRS) Nightfire algorithm for the detection and characterisation of persistent hot spots, including gas flares, to the Sea and Land Surface Temperature Radiometer (SLSTR) observations on-board the Sentinel- satellites. A hot event at temperatures typical of a gas flare will produce a local maximum in the night-time readings of the shortwave and mid-infrared (SWIR and MIR) channels of SLSTR. The SWIR band centered at 1.61 mmis closest to the expected spectral radiancemaximumand serves as the primary detection band. The hot source is characterised in terms of temperature and area by fitting the sum of two Planck curves, one for the hot source and another for the background, to the radiances from all the available SWIR, MIR and thermal infra-red channels of SLSTR. The flaring radiative power is calculated from the gas flare temperature and area. Our algorithm differs from the original VIIRS Nightfire algorithm in three key aspects: (1) It uses a granule-based contextual thresholding to detect hot pixels, being independent of the number of hot sources present and their intensity. (2) It analyses entire clusters of hot source detections instead of individual pixels. This is arguably a more comprehensive use of the available information. (3) The co-registration errors between hot source clusters in the different spectral bands are calculated and corrected. This also contributes to the SLSTR instrument validation. Cross-comparisons of the new gas flare characterisation with temporally close observations by the higher resolution German FireBIRD TET-1 small satellite and with the Nightfire product based on VIIRS on-board the Suomi-NPP satellite show general agreement for an individual flaring site in Siberia and for several flaring regions around the world. Small systematic differences to VIIRS Nightfire are nevertheless apparent. Based on the hot spot characterisation, gas flares can be identified and flared gas volumes and pollutant emissions can be calculated with previously published methods.

Food is one of the basic necessities for all living things in this globe to grow, maintain life and develop. It is a source of energy for almost all bodily functions and it directly affects our health status and how we feel each day and the future. Yet, there are millions of people around the globe who do not have the sumptuousness to provide enough food to themselves and their beloved ones. Ethiopia is one of the highly food insecure countries in the world, it's name has been illustrious for famine and drought for decades. The study's main aim is to assess the livelihood resources and strategies of the smallholding farmers in their strive to achieve food security at household level. For this particular study, from Tigray region, Kilte Awelalo was taken as a study area and three Tabias were selected; Ayenalem, Genfel and Tahetay Adikesanded. The total sample number of households from these three Tabias was 370 and a formal interview schedule was employed to collect relevant primary inputs for the study. The study found that farmland holding size and its fertility as major impacting factors behind the livelihood strategies and food security condition of the smallholding farmers. It was also found that about one third of the total sample population were chronically food insecure, whereas about half of the population were transitory food insecure and rest very little number of households were food secure.

This research aimed to study and compare prevalence of work-related musculoskeletal (MSK) problem and perceived discomfort among port crane operators consisting of quay and rubber tyred gantry (RTG) cranes working in the Laem Chabang Deep-sea Port, Thailand. Direct interviews for a cross-sectional analysis was selected for this unique job with a small amount of sample size. A standardized modified version of the Nordic Musculoskeletal Questionnaire (NMQ) was lunched for 26 male participants, consisting of 11 quay and 15 RTG, where a priori power analysis using G*Power suggested the minimum as 24 for the hypothesis test. Socio-demographic characteristics showed no significant difference among them. The NMQ revealed lower back as the highest prevalent body part (76.9%) followed by neck, shoulders and upper back at the same percentage (23.1%) for all port crane group, with up to 96.2% reporting MSK problem over the past 12 months. And Borg scale rating, assessing the perceived discomfort, revealed lower back with the highest score (2.38) followed by upper back (0.65), shoulders (0.54) and neck (0.5). Remarkably, the comparation between the quey and RTG crane operators on the MSK prevalence (χ2 test) and perceived discomfort levels (Kruskal-Wallis test), regarding different 9 body parts, revealed a significant difference between the two on upper back with quay crane having more problem than the RTG at p &lt; 0.05. while the rest of them were mainly in the same direction. MSK contributors such as: working awkward posture, mental stress, height, trolley distance and vibration are considerably the main causes of this. However, the larger in scale of exposure to those for the quey crane compared to the RTG might have led to the distinguishing MSK problem found in this study which require thoroughly deliberation for the particular solutions.

As an active device, air source heat pumps (ASHP) are widely used for heating and cooling in buildings. However, in cold regions, their efficiency decreases, and frost formation becomes a significant issue during winter. This paper proposes a new scheme that couples air source heat pumps with passive heating. By using software simulations and mathematical models, the new scheme is compared to traditional ASHP systems to analyze its heating performance in rural homes during winter in China’s cold regions. According to the simulation and calculation analysis, on the coldest day of winter, the coupling scheme can provide approximately 99.41kWh of heat to the interior, surpassing the 86.67kWh required to maintain an indoor temperature of 20℃. The system’s power consumption is 36.96 kWh, which is 66.88% lower than that of traditional heat pump heating. The study shows that a coupled system of air source heat pumps and passive heating has better heating performance in cold regions. By incorporating phase change materials and heat storage media to address the shortage of solar energy at night, the system can meet the heating needs throughout the entire day.

The COVID-19 pandemic over the past years has shown a great need for rapid, low-cost and on-site detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). In this paper, an aptamer-based colloidal gold nanoparticle lateral flow test strip was well developed to realize the visual detection of wild type SARS-CoV-2 spike protein (SP) and multiple variants. Under the optimal reaction conditions, a low detection limit of SARS-CoV-2 S protein of 0.68 nM was acquired, and the actual detection recovery was 83.3% to 108.8% for real world samples. This suggests a potential tool for the prompt detection of SARS-CoV-2 with good sensitivity and accuracy, and a new method for the development of alternative antibody test strips for the detection of other viral targets.

Colombia is the world's leading producer of mild washed arabica coffee and produces 12.6 million bags of green coffee, but at the same time 784,000 tons of waste biomass are dumped in open fields, of which only 5% is recovered or used. The objective of this project was to evaluate the production of platform chemicals from these coffee wastes. To achieve this, biomass characterization was carried out using proximate analysis, ultimate analysis and structural analysis. Hydrothermal valorization was carried out at a temperature range of 120-180 °C (LHW) and 180-260 °C (HTC) for one hour, the platform chemicals obtained were quantified by HPLC-IR, monitored by pH and conductivity, and the solid fraction was characterized by monitoring the functional groups in IR spectroscopy, and elemental analysis. Hydrolysis processes were obtained from 150 °C, production of platform chemicals from 180 °C and maximum concentration at 180 °C-4h, over 200 °C degradation of the products in the liquid fraction starts to take place. Homogeneous basic and acid catalysts were used to improve the yields of the reaction. The kinetics of the hydrolysis of lignocellulosic structures to sugars were also analyzed and described, and reaction orders of 1 (LHW), 3 (HTC) and their respective reaction rate equations were reported.

(1) Background: There is insufficient empirical evidence on the correlates of health care utilization of irregular migrants currently living in Turkey. The aim of this study was to identify individual level determinants associated with health service and medication use. (2) Methods: 155 Afghans completed surveys assessing service utilization including encounters with primary care physicians and outpatient specialists in addition to the use of prescription and nonprescription medicines. Multivariate logistic regression analyses were employed to examine associations between service use and a range of predisposing, enabling, and perceived need factors. (3) Results: Health services utilization was lowest for outpatient specialists (20%) and highest for nonprescription medications (37%). Female gender and higher income predicted encounters with primary care physicians. Income, and other enabling factors such as family presence in Turkey predicted encounters with outpatient specialists. Perceived illness-related need factors had little to no influence on use of services; however, asylum difficulties increased the likelihood for encounters with primary care physicians, outpatient services, and the use of prescription medications. 4) Conclusion: This study suggests that health services use among Afghan migrants in Turkey is low considering the extent of their perceived illness-related needs, which may be further exacerbated by the precarious conditions in which they live.

In the decarbonization of the steel, cement, and chemical industry in Germany, green hydrogen is expected to play a crucial role. The utilization of green hydrogen in the production processes of said industries requires organizations to modify their business model, requiring sustainable business model innovation (SBMI). Numerous tools and frameworks that support organizations in the process of SBMI have been proposed in the literature in recent years. However, the applicability of these tools and frameworks for steel, cement, and chemical companies that intend to utilize green hydrogen to produce their goods remains unexplored. By conducting a systematic literature review on tools and frameworks for SBMI, a literature and practice review to identify and analyze existing green hydrogen projects of steel, cement, and chemical companies, and an evaluation of the identified tools and frameworks in an evaluation matrix, this paper aims to assess the suitability of SBMI tools and frameworks for steel, cement, and chemical companies that plan to use green hydrogen to produce their goods. Based on the evaluation, the Cambridge Business Model Innovation Process (CBMIP) was identified as the most suitable SBMI framework.

Background: This study aims to investigate the patient safety culture at a sports medicine hospital and explore quality of healthcare and associated factors. Methods: In a cross-sectional study design, the tool Hospital Survey on Patient Safety Culture (HSOPC) was administered online among staff at a sports medicine hospital in Doha, Qatar. About 319 staff participated from 898 staff who received emails (35.5%). Results: The results showed that 49.2% of the staff rated the patient safety grade as excellent and 36.1% as very good, which sums up to 85.3%. Factors associated with better patient safety grade were work climate (OR 10.3 95% CI (3.2 to 33.6); teamwork OR 7.6 95% CI (2.8 to 20.9) and team communication (OR 2.9 95% CI (1.1 to 7.6). Conclusions: Addressing the work climate, enhancing communication, and cohesive work within teams facilitates a culture of trust that improves patient safety grade. Ensuring quick return to play is a team effort involving multiple disciplines, hence a high performance and safety culture can enhance teamwork. Reducing punitive response to error and encouraging staff and supervisors are key areas that can improve safety culture in sports medicine organizations, and efforts should be placed in this area.

In the literature on occupational stress and recovery from work several facets of thinking about work in off-job time have been conceptualized. However, research on the focal concepts is currently rather disintegrated. In this study we take a closer look at the five most established concepts, namely (1) psychological detachment, (2) affective rumination, (3) problem-solving pondering, (4) positive work reflection, and (5) negative work reflection. More specifically, we scrutinized (1) whether the five facets of work-related rumination are empirically distinct, (2) whether they yield differential associations with different facets of employee well-being (burnout, work engagement, thriving, satisfaction with life, and flourishing), and (3) to what extent the five facets can be distinguished from and relate to conceptually similar constructs, such as irritation, worry, and neuroticism. We applied structural equation modeling techniques to cross-sectional survey data from 474 employees. Our results provide evidence that (1) the five facets of work-related rumination are highly related, yet empirically distinct, (2) that each facet contributes uniquely to explain variance in certain aspects of employee well-being, and (3) that they are distinct from related concepts, albeit there is a high overlap between (lower levels of) psychological detachment and cognitive irritation. Our study contributes to clarify the structure of work-related rumination and extends the nomological network around different types of thinking about work in off-job time and employee well-being.

The concept of using special electrical circuit design realize a "cold resistors", that is, an active resistor circuitry with lowered effective noise temperature, was first introduced about 80 years ago. Later on, various kinds of artificial resistors were applied in different research areas, such as gravitational wave detection, photo-amplifiers and quartz oscillators. Their proofs of concepts were experimentally proved. Unfortunately, the complete theory was not found even though several attempts had been published, sometimes with errors. In this paper, we describe a correct and complete circuit theoretical model of a cold resistor system. The results are confirmed by computer simulations. A design tools for this circuit is also shown.

Concrete being one of the most frequently used construction materials in the field of construction. The use of concrete has increased with the passage of time as the more and more construction activities are taking place around the globe. Different materials have been added in to the concrete mix to provide the concrete more strength and make it more durable and long lasting. This paper looks into a detailed comparison of concrete strength when casted with in the presence of carbon fibers, steel fibers and glass fibers. The compressive strength for cubes and cylinder with carbon fibers is the highest as compare to steel fibers as well as glass fibers. The compressive strength of concrete is measured on 3 day, 7 day, 14 day and 28 day strength. The compressive strength of cube on 28th day strength is 37.52 MPa for carbon fiber steel, for steel fiber it is 34.22 MPa and with glass fiber the strength is 29.335 MPa whereas the compressive strength of cylinder with carbon fibers the 34.88 MPa, with steel fiber it is 34.22 MPa and with glass fiber the strength is 27.447 MPa. For the cubes the maximum difference between different fibers inducted concrete sample is 28% approximately and for cylinder it is 27%, respectively. On the other hand, the tensile strength of concrete was also gained with the carbon fiber. It was determined that carbon fiber provided about 16% and 12.8% tensile strength higher than glass and steel fibers respectively.

The objective of this study is to evaluate the effect of constitutive equations on the prediction accuracy for springback in cold stamping with various deformation modes. In this study, two types of yield functions—Hill’48 and Yld2000-2d—were considered to describe yield behavior. Isotropic and kinematic hardening models based on the Yoshida–Uemori model were also adopted to describe hardening behavior. Various material tests (such as uniaxial tension, tension- compression, loading-unloading, and hydraulic bulging tests) were carried out to determine the material parameters of the models. The obtained parameters were implemented in the finite element (FE) simulation to predict springback, and the results were compared with experimental data. U-bending and T-shape drawing were employed to evaluate the springback prediction accuracy. Obviously, the springback prediction accuracy was greatly influenced by constitutive equations. Therefore, it is important to choose appropriate constitutive equations for accurate description of material behaviors in FE simulation.

The hot wire anemometer is a commonly used device for measuring air speed in laboratories. In this paper, the relationship between air speed and the hot wire temperature in different air speed ranges was analyzed based on the theory of thermal equilibrium. A measurement circuit and hot wire shape were designed based on the principle of the hot wire anemometer, and the linear relationship between current and temperature in the hot wire at different air speeds was verified in an adjustable air speed field. The measured current was used to represent air speed. The designed hot wire anemometer was experimentally validated to provide measurement results that match the theoretical values in different air speed ranges. Finally, the sensitivity of the anemometer in different measurement ranges was determined based on the uncertainty of the instrument's sensitivity and the measurement formula.

The new slide roller burnishing (SRB) method has been developed to produce mirror-like surfaces. Unlike conventional roller burnishing (RB), SRB is implemented through a unique device that allows the axes of the deforming roller and the rotary workpiece to cross resulting in a relative sliding velocity that can be controlled (in magnitude and direction) by varying the crossing angle. In the present work, the effect of SRB on the fatigue behavior of AISI 316 steel fatigue specimens was investigated by comparing with a conventional RB using the basic correlation in surface engineering: finishing–surface integrity (SI)–operating behavior. To obtain a more representative picture of the comparison, we implemented each method (RB and SRB) with two combinations of governing factors: (A) a radius of the roller toroidal surface of 3 mm, a burnishing force of 250 N and feed rate of 0.05 mm/rev (RB-A and SRB-A) and (B) a radius of the roller toroidal surface of 4 mm, a burnishing force of 550 N and feed rate of 0.11 mm/rev (RB-B and SRB- B). Both SRB-A (crossing angle of –45°) and SRB-B (crossing angle of –30°) achieved mirror-finish surfaces. SRB-B lead to the greatest fatigue strength and, thus, the longest fatigue life among all tested processes. SRB-B created the deepest zone (&gt;0.5 mm) with residual compressive macro-stresses and a clearly defined modified surface layer, whose thickness of more than 20 m is about twice that created by the other three processes.

The average working person can spend between 35-60 hours a week in the workplace, making it an influential place for mental well-being while also being a place for socio-economic contribution. Workplace incivility can diminish positive mental health outcomes and negatively impact work engagement through increased social anxiety. To investigate this, 118 working adults aged between 19 to 67 years old in Singapore were recruited for a survey comprising of demographics questions, the Workplace Incivility Scale, Brief DSM-5 Social Anxiety Disorder Severity Scale, Utrecht Work Engagement Scale-9 over the period of November 2022 to April 2023. Correlational, regression and mediation analysis showed workplace incivility scale scores to significantly pre-dict social anxiety after controlling for covariates, supporting our hypothesis that employees exposed to work-place incivility would have higher levels of social anxiety that mediated work engagement after controlling for age and gender. The findings here show workplace incivility to be a possible intervention target for social anx-iety to reduce negative impacts on work engagement in order to improve employee experience and retention for organizations.

The interactions between work and personal life are important for ensuring well-being especially during COVID-19 where the lines between work and home are blurred. Work-life interference/imbalance can result in work-related burnout, which has been shown to have negative effects on faculty members’ physical and psychological health. Although our understanding of burnout has advanced considerably in recent years, little is known about the effects of burnout on nursing faculty turnover intentions and career satisfaction. Thus, this study aimed to test a hypothesized model examining the effects of work-life inference on nursing faculty burnout (emotional exhaustion and cynicism), turnover intentions and ultimately, career satisfaction. A predictive cross-sectional design was used. An online national survey of nursing faculty members was administered throughout Canada in Summer 2021. Nursing faculty who held full-time or part-time positions in Canadian academic settings were invited via email to participate in the study. Data was collected from an anonymous survey housed on Qualtrics. Descriptive statistics and reliability estimates were computed. The hypothesized model was tested using structural equation modeling. Data suggest that work-life interference significantly increase burnout which contribute to both higher turnover intentions and lower career satisfaction. Turnover intentions in turn was negatively associated with career satisfaction. The findings add to the growing body of literature linking burnout to turnover and dissatisfaction, highlighting key antecedents and/or drivers of burnout among nurse academics. These results provide suggestions for suitable areas for the development of interventions and policies within the organizational structure to reduce the risk of burnout during and post-COVID-19 and improve faculty retention.

The paper presents the problem of damage detection in steel girders. Static displacements at the selected point of the structure play the role of measured variables. Structural response signal decomposition is performed according to the Mallat pyramid algorithm, which is used to perform the discrete wavelet transform (DWT). This procedure allows us to quite well determine the location of structural damage. The geometry and the placement of any defective part of the structure may have a random character. It can be assumed that the random processes occurring in the broadly understood structure mechanics are Gaussian in nature. The first four probabilistic moments are estimated using three approaches independent: semi-analytical (SAM), perturbative (SPT), and Monte-Carlo simulations (MCS). The semi-analytical random approach seems to be the most optimal due to the necessary computation time. The incorporation of the mathematical stochastic apparatus into the classical (deterministic) analysis of the statics of the structure makes it possible to estimate the reliability measures of the analyzed girder.

Bacteria can colonize and develop biofilm on a large variety of biotic and abiotic materials, it is accountable for nosocomial infections and chronic illness and consequently, it is a serious economic and public health problem. Staphylococcus epidermidis, thanks to its ability to form biofilm and colonize biomaterials, represents the most frequent causative agent involved in bio-film-associated infections of medical devices. Due to the biofilm presence, S. epidermidis infections are extremely difficult to treat and the research of new molecules able to interfere with its biofilm formation has a remarkable interest. In the present work, the attention was focused on Pseudomonas sp. TAE6080, an Antarctic marine bacterium able to produce and secrete an effective antibiofilm compound. The molecule responsible for this activity was purified by an activity-guided approach and it resulted to be a periplasmic protein, named Cold-Azurin. The Cold-Azurin was recombinantly produced in E. coli and purified. The recombinant protein was able to impair S. epidermidis attachment to the polystyrene surface and effectively prevent biofilm formation.

In the realm of metal steel and iron manufacturing, there is a constant drive to optimize production efficiency and enhance the quality of the final products. This abstract explores a paradigm shift in this industry through the utilization of Computational Fluid Dynamics (CFD) as a powerful tool for achieving these goals .The study focuses on various critical aspects of the manufacturing process. Firstly, it delves into three-phase processes such as slag and gas entrainment in liquid steel, which have a significant impact on the overall product quality. Understanding and optimizing these processes is crucial to ensure the desired chemical composition and physical properties of the final metal.The abstract investigates the role of CFD in vacuum degassing, a process that plays a pivotal role in removing impurities, such as hydrogen and oxygen, from the liquid steel. By leveraging CFD to simulate and analyze the fluid flow patterns, researchers and engineers can design more efficient vacuum degassing systems, leading to improved product purity and reduced waste.Another crucial aspect explored in this abstract is the alloy melt and mixing process. By employing CFD simulations, researchers can gain insights into the movement of different alloy components and optimize their distribution within the melt. This aids in achieving the desired alloy composition, ensuring uniformity, and enhancing the mechanical properties of the final product.In addition, the study delves into the movement and flotation of inclusions, which are unwanted impurities present in the metal. CFD can be utilized to model and analyze the behavior of these inclusions, enabling engineers to design efficient strategies for their removal, thereby enhancing the purity and integrity of the final product.Moreover, the abstract considers the impact of melt temperature losses, which can occur during different stages of the manufacturing process. By employing CFD, it becomes possible to understand and mitigate these temperature losses, leading to improved energy efficiency and better control over the manufacturing parameters.Part 1 of this abstract critically evaluates the use of CFD in iron making, analyzing its benefits and limitations. It highlights how CFD can aid in process optimization, improving the understanding of complex phenomena involved in iron making, and ultimately leading to enhanced production efficiency.Part 2 focuses on the application of CFD in steel making and steel operation. It explores the fluid flow dynamics during different stages of steel production, including refining, casting, and rolling. By leveraging CFD, engineers can optimize these processes, leading to improved product quality, reduced defects, and increased productivity.This abstract demonstrates the transformative potential of Computational Fluid Dynamics in metal, steel, and iron manufacturing. By utilizing CFD as a tool to model and analyze complex fluid flow phenomena, researchers and engineers can revolutionize the production process, maximizing efficiency, and ensuring high-quality end products.

Focusing on the problem of identifying and classifying aero-engine models, this paper measures the infrared spectrum data of aero-engine hot jets using a telemetry Fourier transform infrared spectrometer. Simultaneously, infrared spectral data sets with the six different types of aero-engines are created. For the purpose of classifying and identifying infrared spectral data, a CNN architecture based on the continuous wavelet transform peak seeking attention mechanism (CWT-AM-CNN) is suggested. This method calculates the peak value of middle wave band by continuous wavelet transform, and the peak data is extracted by the statistics of the wave number locations with high frequency. Attention mechanism is used for the peak data, and the attention mechanism is weighted to the feature map of the feature extraction block. The training set, vali-dation set and prediction set are divided in the ratio of 8:1:1 for the infrared spectral data sets. For three different data sets, CWT-AM-CNN proposed in this paper is compared with the classical classifier algorithm based on CO2 feature vector and the popular AE, RNN and LSTM spectral processing networks. The prediction accuracy of the proposed algorithm in the three data sets is as high as 97%, and the lightweight network structure design not only guarantees high precision, but also has a fast running speed, which can realize the rapid and high-precision classification of the infrared spectral data of the aero-engine hot jets.

Modular steel buildings (MSBs) interlocking inter-module connections (IMCs) have piqued researchers’ interest. However, the existing literature has not yet studied the optimisation of its plate thicknesses. This paper, therefore, focuses on optimising interlocking (IMCs) plate thickness in (MSBs), leveraging previous experimental and numerical simulation methodologies. Various numerical models for four MSBs interlocking (IMCs) with plate thicknesses (4 mm, 6 mm, 10 mm, and 12 mm) were developed under compression loading conditions. The study’s novelty lay in its comprehensive parametric analysis, which evaluated the slip phenomenon in (MSBs) connections and introduced a slip prediction model validated against empirical data. Further innovative machine learning approach was utilised to predict slip values based on applied force through a random forest regression model trained using the 'Treebagger' function. Sensitivity analysis and comparisons with alternative methods were utilised to underscore the reliability and applicability of the findings. The results showed that 11.03 mm was the optimal plate thickness for interlocking (IMCs) in modular steel buildings, with up to 8.08% reduced material costs. Increasing plate thickness boosts its deformation resistance by up to 50.75%. ‘TreeBagger’ random forest for anomaly detection and machine learning improves slip prediction up to 7% at higher force levels.

Neurofeedback (NF) shows promise in enhancing memory, but its application to the medial temporal lobe (MTL) still needs to be studied. Therefore, we aimed to develop an NF system for the memory function of the MTL and examine neural activity changes, and memory task score changes through NF training. We created a memory NF system using intracranial electrodes to acquire and visualise the neural activity of the MTL during memory encoding. Twenty trials of a tug-of-war game per session were employed for NF and designed to control neural activity bidirectionally (Up/Down condition). NF training was conducted with three patients with intractable epilepsy, and we observed an increasing difference in NF signal between conditions (Up−Down) as NF training progressed. Similarities and negative correlation tendencies between the transition of neural activity and the transition of memory function were also observed. Our findings demonstrate NF's potential to modulate MTL activity and memory encoding. Future research needs further improvements to the NF system to validate its effects on memory functions. Nonetheless, this study represents a crucial step in understanding NF's application to memory and provides valuable insights for developing more efficient memory enhancement strategies.

Speckle Plethysmography (SPG) and Photoplethysmography (PPG) are different biophotonics technologies that allow for measurement of hemodynamics. As the difference between SPG and PPG under low perfusion conditions is not fully understood, a Cold Pressor Test (CPT) was used to modulate blood pressure and peripheral circulation. A custom-built setup simultaneously derived SPG and PPG from the same video streams at two wavelengths (639 nm and 850 nm). SPG and PPG were measured at right index finger location before and during CPT using finger Arterial Pressure (fiAP) as reference. The effect of CPT on Alternating Component amplitude (AC) and Signal-to-Noise-Ratio (SNR) of dual-wavelength SPG and PPG signals was analysed across participants. Furthermore, waveform differences between SPG, PPG, and fiAP based on frequency harmonic ratios, were analysed for each subject (n=10). Both PPG and SPG at 850 nm show a significant reduction during CPT for both AC and SNR. However, SPG showed significantly higher and more stable SNR than PPG in both study phases. Harmonic ratios were found substantially higher in SPG than PPG. Therefore, in low perfusion conditions, SPG seems to offer a more robust pulse wave monitoring with higher harmonic ratios than PPG.

Autoimmune hemolytic anemia is a rare condition characterized by destruction of red blood cells with and without involvement of complement. It is associated with significant morbidity and mortality. In warm autoimmune hemolytic anemia less than 50% of patients remain in a long-term remission following initial steroid therapy and subsequent therapies are required. Cold agglutinin disease is a clonal hematologic disorder which requires therapy in majority of patients and responds poorly to steroids and alkylators. Rituximab has a favorable toxicity profile and has demonstrated efficacy in autoimmune hemolytic anemia in first line as well as relapsed setting. Rituximab is the preferred therapy for steroid refractory wAIHA and as part of the first- and second-line treatment of cold agglutinin disease. This article reviews the mechanism of action of the rituximab and current literature its role in management of primary and secondary warm autoimmune hemolytic anemia and cold agglutinin disease.

Plants have evolved tightly regulated strategies to adapt and acclimate to a changing environment to ensure their survival. Various environmental factors affect plant distribution, growth and yield. Low temperature belongs to those abiotic factors which significantly constrain range boundaries of plant species. Exposing plants to low but non-freezing temperature induces a multigenic processes termed cold acclimation, which finally results in an increased freezing tolerance. Cold acclimation comprises reprogramming of the transcriptome, proteome and metabolome and affects communication and signaling between subcellular organelles. Reprogramming of the central carbohydrate metabolism plays a key role in cold acclimation. This review summarizes current knowledge about the role of carbohydrate metabolism in plant cold acclimation. A focus is laid on subcellular metabolic reprogramming, its thermodynamic constraints under low temperature and mathematical modelling of metabolism.

The recent pandemic has greatly stressed supply chains, treatment modalities, and medical resources. Cold atmospheric plasma (CAP) has been used for a wide range of applications in biomedical engineering due to its many components including electrons, charged particles, reactive oxygen species (ROS), reactive nitrogen species (RNS), free radicals, ultraviolet (UV) photons, molecules, electromagnetic fields, physical forces, and electric fields. In this manuscript, we develop CAP devices for COVID-19. Our manuscript indicates the advantages of highlydeployable CAP devices for both sanitation and treatment, without the need for supply chains of special consumables such as hand sanitizers and the like. We hope that this timely research will help engage the broader community of engineers that wish to help the medical community with this pandemic and to prevent and treat future outbreaks.

Although various atmospheric corrosion simulation models have been developed that give good results, industrial environments are still challenging. This paper aims to investigate the effect industrial atmospheres in Bor on the mechanical properties of structural steel S235JR and to create a constitutive model and also laboratory experimental conditions that will give the best results as an accelerated corrosion test. Atmospheric corrosion tests lasted six months, using sites close to the Electrolytic Refining Plant and Sulphuric Acid Plant, as well as air quality monitoring stations at a remote location in the city of Bor. The laboratory experiments included a salt chamber test lasting 120 h and 240 h and immersing the specimen in the electrolyte from the Electrolytic Refining Plant for 30 days. The results were compared with the standard specimens stored in the laboratory. The X-ray diffraction (XRD) method was used to identify the composition of corrosion products. The scanning electron microscopy (SEM) analysis was applied to analyze the fracture surfaces of the specimens. The use of the Complete Gurson Model (CGM) described the tensile characteristics of the corroded specimens. The study has shown that an enhanced acceleration model and conditions could be developed using numerical analysis of the test results.

We study the work fluctuations in ergotropic heat engines, namely two-strokes quantum Otto engines where the work stroke is designed to extract the ergotropy (the maximum amount of work by a cyclic unitary evolution) from a couple of quantum systems at canonical equilibrium at two different temperatures, whereas the heat stroke thermalizes back the systems to their respective reservoirs. We provide an exaustive study for the case of two qutrits whose energy levels are equally spaced at two different frequencies by deriving the complete work statistics. By varying the values of temperatures and frequencies, only three kinds of optimal unitary strokes are found: the swap operator U1, an idle swap U2 (where one of the qutrits is regarded as an effective qubit), and a non trivial permutation of energy eigenstates U3, which indeed corresponds to the composition of the two previous unitaries, namely U3 = U2U1. While U1 and U2 are Hermitian (and hence involutions), U3 is not. This point has an impact on the thermodynamic uncertainty relations (TURs) which bound the signal-to-noise ratio of the extracted work in terms of the entropy production. In fact, we show that all TURs derived from a strong detailed fluctuation theorem are violated by the transformation U3.

In the ongoing Covid-19 pandemic, if a preventive restriction (PR), intended to arrest the transmission of the virus, is effective we expect a decrease in the rate of transmission. If an effective PR is lifted or relaxed, the rate may show some increase. We test this expectation in the history of PR imposition and relaxation in all countries based on available public database. We found marginal or no negative correlation between standing stringency index of PR and change in slope of the local curve. A change in stringency index was significantly negatively correlated with change in slope, but change in stringency of PRs could explain only 6.1 percent of the variance in rates of transmission. The distribution of slope changes after imposing versus after relaxing PRs was highly overlapping with only a tail consisting of 4.5 % PR impositions being clearly non-overlapping with PR relaxation. Non-parametrically, only 9.4% of PR impositions were associated with a reduction in the slope above the expectation of a null hypothesis. In brief, globally, preventive restrictions have played a very small role in the pandemic process over the one year period. This feedback needs to be considered in making policy for disease prevention in the further course of the pandemic as well as in any future threats of respiratory disease epidemics.