Impure and pure casts have collected reasonable attentions over all the world. In this paper, Aluminum (Al) and Copper (Cu) cast alloys are considered to be studied. Multiple impure and pure Al-Cu cast alloys are established under the condition of very high temperatures. Then, all of the established alloys are examined by applying mechanical tests. More specifically, tests of hardness are exploited. Moreover, different quenching conditions are employed and analyzed. These are the water, air and oil. Consistent results are separately obtained for the impure and pure materials.

Aluminum base alloys containing chromium (Cr) and zinc (Zn) were produced using extrusion and heat treated powder metallurgy. Cr addition ranged between 5 to 10 wt. % while Zn was added in an amount between 0 to 20 wt. %. Heat treatment processes were performed during powder metallurgy process at different temperatures followed by water quenching. Similar alloys were extruded, with an extrusion ratio of 4.6 to get proper densification. Optical microscopy was used for microstructure investigations of the produced alloys. The element distribution microstructure study was carried out using the Energy Dispersive X-ray analysis method. Hardness and tensile properties of the investigated alloys have been examined. Wear resistance tests were carried out and the results were compared with these of the Al-based bulk alloys. Results showed that the aluminum base alloys containing 10wt. % Chromium and heat treated at 500°C for one hour followed by water quenching exhibited the highest wear resistance and better mechanical properties.

The development of Al-Ni alloys with a controlled microstructure has had a great impact on the field of study of aluminum-based alloys. In the present research, the influence of thermal parameters on the grain structures resulting from the directional solidification process of Al-Ni alloys with different alloy content has been studied. It has also been evaluated how different structures and the distribution of second phases influence the corrosion behavior and microhardness of alloys. The columnar-to-equiaxed transition (CET) was observed to occur when the temperature gradient in the melt decreased to values between 1.3 to 2.9 ° C/cm. In addition, a small increase in the microhardness values was observed as a function of the Ni-content. When the Ni-content increase, the resistance to polarization decreases for samples with equiaxed grain structure, throughout the range of compositions studied. Furthermore, the equiaxed grain structure presents higher resistance to polarization values than the columnar grain zone, for alloys with a composition equal to or lower than the eutectic composition.

New corrosion inhibitor derived from coumarin-3-amine namely 3-((2-chlorobenzylidene)amino)coumarin was synthesized and characterized by CHN elemental analysis in addition to Fourier transform infrared and nuclear magnetic resonance techniques. The anti-corrosion ability of 3-((2-chlorobenzylidene)amino)coumarin to inhibit the impacts of corrosion has been demonstrated and damage reduction of the mild steel also. 3-((2-chlorobenzylidene)amino)coumarin, has been employed as a good corrosion inhibitor for mild steel in HCL solution. The efficiency of the inhibition was figured according to weight loss method and it was 74.6%.

Corrosion inhibitors are the natural or synthetic compounds that have the ability to inhibit the average of corrosion and reduce the damage of the mild steel. Enormous organic inhibitors nowadays employed in the corrosion domain but excluded due to costly. Comparatively cheap, and stable organic compound, namely 3-((4-nitrobenzylidene)amino)coumarin, have been utilized as an excellent corrosion inhibitor in hydrochloric acid for mild steel. The inhibition efficiency has been figured regarding to weight loss method. The corrosion inhibitor was identified according to spectroscopic techniques namely Fourier transform infrared and nuclear magnetic resonance in addition to micro-elemental analysis. Inhibition efficiency for the studied inhibitor was 71.4% that, at the highest studied concentration.

This study introduces a novel nanocomposite coating composed of PANI/CeO2 nanocomposite films, aimed at addressing corrosion protection needs. Analysis through FTIR spectra and XRD patterns confirms the successful formation of the nanocomposite films. Notably, the PANI/CeO2 nanocomposite films exhibit a hydrophilic nature. The bandgap energy of the PANI composite film measures at 3.74 eV, while the introduction of CeO2 NPs into the PANI matrix reduces the bandgap energy to 3.67 eV. Furthermore, the electrical conductivity of the PANI composite film is observed to be 0.40 S.cm-1, with the incorporation of CeO2 NPs leading to an increase in electrical conductivity to 1.07 S.cm-1. To evaluate its efficacy, electrochemical measurements were conducted to assess the corrosion protection performance. Results indicate a high protection efficiency of 92.25% for the PANI/CeO2 nanocomposite film.

Improvement of hydrophysical properties and corrosion resistance of self-compacting concrete to the effects of alternate freezing-thawing and aggressive soils of southern and central Kazakhstan is of interest to a wide range of researchers from the side of practical application of the obtained results in construction practice. It is proposed to form a spatially reinforced fine crystalline structure of cement matrix with maximum dense packing by using a complex modifier (Hyperplasticiser + Polymer + Microsilica + Fibro fibers) in the composition of self-compacting concretes (SCC). The introduction of the calculated amount of the above additives increases the operational reliability of the current SCC compositions, increasing the water resistance to W16, frost resistance to F=500, increasing the compressive strength by 20%, reducing the mass loss of samples during corrosion leaching to 50%. It has been experimentally established that the proposed addition of complex modifier (Hyperplasticiser + Polymer + Microsilica + Fiber fibers) to the SCC composition allows obtaining self-compacting concrete of high quality with improved performance characteristics (compressive strength, water resistance, frost resistance and corrosion resistance). Studies have shown that the complex modifier-modified SCC compositions have a high degree of resistance in aggressive environments and leaching corrosion. Based on the results of the conducted tests, it is possible to recommend the obtained SCC compositions for production of building products working in the zone of alternating freezing-thawing and aggressive soils.

The effect of retrogression re-aging treatment (RRA) on corrosion behavior of 7055 Al-Zn-Mg alloy were studied. Results provides the corrosion resistance could be greatly improved by RRA. After the RRA treatment, the isolated precipitates occurred on grain boundaries (GBs) and the low angle grain boundaries (LAGBs) presented a larger fraction compared to the single-stage peaking aging. The samples after RRA treatment also show better corrosion resistance than the single-stage peak aging. The results of electrochemical impedance spectroscopy (EIS) show that impedance spectrum is consisted of semi-infinite layer diffusion impedance and stagnant Weber impedance. The semi-infinite layer diffusion impedance corresponded a limited retention layer on the electrode surface. In corrosion process, Weber impedance corresponded to stagnant layer of corrosion products generated by the anode branches. The RRA sample has the high Rf and low Cf, Cp values, and the corrosion current density of the RRA samples is ten times less than the single-stage peak aging samples with the 10% hardness losing.

In this project, four of fibers Bragg gratings were fabricated by injecting different volumes of liquids (star line Glass Mechanix optical adhesive material, olive oil diluted with ethanol) into the hollow core fiber. The amplitude splitting interferometric technique with a high resolution specially designed translation stage was used for the fabrication process. The fabrication was done using ultraviolet laser operated at wavelength 405nm. The fabricated Bragg length of the four fibers is equal to 3.8 cm. The results presented fiber Bragg grating (FBG) with successful fabrication at 653.3 nm Bragg reflected wavelength.

Structural and functional materials are subjected to harsh oxidizing environments that lead to a rapid decline in their surface chemical stability. At high-temperatures, the diffusion of atoms is erratic; thus, the reactive elements (REs) get a chance to migrate to the surface and look for oxygen-reactive sites. Their migration from the lattice sites creates vacancies in the matrix and thus weakens the bond, making the material prone to environmental degrading factors. Subsequently, the inward diffusion of oxygen, sulfur, nitrogen, or carbon may occupy these vacancies, resulting in undesired precipitation at the grain boundary, which is usually brittle. The solubility and dissociation of attacking species and corrosion products play the most critical role in corrosion in high-temperature water. To evade such situations, Ti, Al, and Cr are added in Ni/Fe-based alloys, forming a dense oxide layer on the surface that impedes further surface migration of ions. The stability of the alloys is then determined by the capability of these oxide layers to heal or reform during spalling/cracking. This review attempts to understand the migration of REs at the interfaces to prepare structural materials in any unexpected set of oxidizing service conditions. This review will also try to establish the interaction mechanism of REs novel/conventionally added in the alloys with the oxidizing elements in the environments to design better degradation-resistant high-temperature alloys.

The inhibition impacts of 1,10-Phenanthroline-5,6-diamine (PTDA) on mild steel in 1 M HCl solution were investigated through weight loss method. The inhibition efficiencies of PTDA increase with increase in PTDA concentration at the temperature 303. Weight loss method indicate that PTDA is an excellent inhibitor the inhibition efficiency of 81.5% at the maximum PTDA concentration of 0.5 g/L at the temperature 303K.

A series of waterborne polyurethane (WBPU)/modified lignin amine (MLA) adhesives was prepared using modified lignin amine (MLA) as a chain extender by a prepolymer mixing process. A successful Mannich reaction was achieved during the synthesis of MLA by reacting lignin with bis(3-aminopropyl)amine. Higher tensile strength, Young’s modulus and thermal stability were recorded for WBPU/MLA adhesives with higher MLA contents. The WBPU/MLA adhesive materials were used to coat PVC substrates. The adhesive strength increased with increasing MLA content. More importantly, the MLA also enhanced the WBPU/MLA coating in terms of adhesive strength at moderately high temperatures as well as under natural weather exposed conditions. The adhesive strength was essentially unaffected with 6.48 mole% MLA in the WBPU/MLA coating after exposure to natural weather conditions for 180 days.

Demand for environmentally friendly types of energy is growing all over the world, which naturally increases the intensity of work on the production of hydrogen-containing fuel mixtures. Steam reforming of methanol is one of the most effective areas of research, as it is a process with low energy consumption. The results of steam reforming of methanol on the catalysts prepared by solution combustion synthesis (SCS) and impregnation by moisture capacity are presented. Investigation of the activity of Cu-Ce-Al catalysts of different composition was carried out for production of hydrogen and comparison of SCS with traditional impregnation method. Methanol conversion reaches 99%, while the selectivity of H2 was 88%, at 500 °C. It was found that CuAl2O4 spinel formation is due to substitution of Al3+ with Cu2+ Ce3+ cations. A consequence CuAl2O4 and CeAlO3 lattice parameters increase because of difference in ionic radius of Al3+ (0.53 Å) and Cu2+ (0.73 Å), Ce3+ (1.07 Å). Advantages of SCS catalysts in steam reforming of methanol were shown. The aim of this research is to develop a new catalyst for conversion of methanol into hydrogen containing fuel mixtures, which will further promote the organization of a new era of environmentally friendly energy-saving production methods.

Background: Asthma is a widespread chronic respiratory disease that poses a significant public health challenge. The current study investigated the associations between air pollution and asthma severity among individuals residing near the Sohar industrial port (SIP) in Oman. Despite the presence of multiple major industrial complexes in Oman, limited knowledge regarding their impact on respiratory health is accredited. Hence, the primary objective of this study is to offer valuable insights into the respiratory health consequences of industrial air pollution in Al Batinah North. Methods: The state health clinics' records for patient visits related to asthma were collected for the timeframe spanning 2014 to 2022. Exposure was defined as the distance from SIP, Majan Industerial Area (MIA) and Sohar Industerial Zone (SIZ) to determine high, intermediate, and low exposure zones (12 km, respectively). Exposure effect modifications by age, gender, and smoking status were also examined. Results: The conducted cross-sectional study of 410 patients (46.1% males and 53.9% females) living in over 17 areas around SIP revealed that 73.2% of asthmatics were under 50 years old, with severity significantly associated with closeness to the port. Risk ratios were estimated to be (RR:2.42; CI95%: 1.01–5.78), (RR:1.91; CI95%: 1.01–3.6), and (RR:1.68; CI95%: 0.92–3.09) for SIP, MIP and SIZ areas, respectively, compared to the control area. Falaj Al Qabail (6.4 km) and Majees (6 km) had the highest number of asthma patients (N. 69 and N. 72), and highest percentages of severe asthma cases among these patients (28% and 24%) with significant risk ratios (RR:2.97; CI95%: 1.19–7.45 and RR:2.55; CI95%: 1.00–6.48), correspondingly. Moreover, severe asthma prevalence peaked in the 25-50 age group (RR:2.05; CI95%: 1.26–3.33), and this linkage between asthma and age was much more pronounced in males than females. Smoking and exposure to certain contaminant (dust and smoke) increased also the risk of severe asthma symptoms, but their effects were less important in the high risk zone, suggesting much more important risk factor. A neural network model accurately predicted asthma risk (94.8% accuracy), with proximity to Sohar Industrial Port as the most influential predictor. Conclusion: The study highlights the High asthma burden near Sohar Industrial Port, linked to port proximity and smoking and wind direction as major risk factors. These findings inform vital public health policies to reduce air pollution and improve respiratory health in the region, prompting national policy review.

Today, legislative framework addresses the metal alloys’ corrosion issues, demanding the re-striction of use of the probable carcinogenic, mutagenic and toxic for reproduction at humans (CMG) metals, like nickel, cobalt and chromium, and demand to develop new biomaterials. Therefore, the aim of this research is to evaluate and compare ion release of standard dental alloys and their hypoallergenic equivalents. Six types of orthodontic alloy wires (nickel-titanium (NiTi), coated NiTi, stainless steel (SS), Ni-free SS, cobalt-chromium (CoCr), and titanium-molybdenum (TMA) were immersed into artificial saliva of pH 5.5 and 6.6. Release of metal ions was measured by inductively coupled plasma-mass-spectrometry (ICP-MS) after 3, 7, 14 and 28 days. Data analyses were done using analysis of variance, results with P

Although various atmospheric corrosion simulation models have been developed that give good results, industrial environments are still challenging. This paper aims to investigate the effect industrial atmospheres in Bor on the mechanical properties of structural steel S235JR and to create a constitutive model and also laboratory experimental conditions that will give the best results as an accelerated corrosion test. Atmospheric corrosion tests lasted six months, using sites close to the Electrolytic Refining Plant and Sulphuric Acid Plant, as well as air quality monitoring stations at a remote location in the city of Bor. The laboratory experiments included a salt chamber test lasting 120 h and 240 h and immersing the specimen in the electrolyte from the Electrolytic Refining Plant for 30 days. The results were compared with the standard specimens stored in the laboratory. The X-ray diffraction (XRD) method was used to identify the composition of corrosion products. The scanning electron microscopy (SEM) analysis was applied to analyze the fracture surfaces of the specimens. The use of the Complete Gurson Model (CGM) described the tensile characteristics of the corroded specimens. The study has shown that an enhanced acceleration model and conditions could be developed using numerical analysis of the test results.

A huge part of corrosion failures and even of catastrophes takes origin from a trivial mistake in either choice or connection of different materials, as well as from an inaccurate evaluation of the compatibility between materials an environment. The example shown in the present paper summarizes several wrong solutions due to the lack of knowledge of the basic rules of corrosion control. By chance, either the consequences of such mistakes were so precocious that it was possible to find a remedy during the construction, or they were happily so venial as to be tolerated. This paper is third in a series devoted to enhancing the need of a professional corrosion control design for infrastructures.

The variability of ozone over Egypt has been studied in this work. Higher values of coefficient of variation (COV) at eight stations occur at winter while lowest values occur at summer. The COV is function of latitude in annual, winter and spring where it decreases gradually from the north to south of Egypt. The trend analysis of ozone over the eight stations indicates negative trends over northern stations for both annual and seasonal time series with the greatest one at winter. The horizontal distribution of ozone trend values is negative over all Egypt in winter while it positive over middle and south Egypt in the other seasons. The long-term variability of the behavior of the annual ozone shows positive trend values in ozone are the dominant features during the period 1979- 1989 at the most stations. Negative trend values in ozone are the dominant features during the period 1990- 2014 at all stations. The Mann–Kendall test confirms that there is an abrupt change towards decreasing of ozone occurs in 1981, 1984, 2012, 1999, 2000, 1998 and 2010, while a change towards increasing of ozone appears in 2006, 2014, 1993 and 1989.

This paper studies the use of zinc oxide nanoparticles (ZnO-NPs) synthesized using an extract of convolvulus leaves and expired ZnCl₂, as an efficient inhibitor for carbon steel corrosion in 1M HCl solution. ZnO-NPs are characterized by Fourier-transform infrared spectrophotometer (FTIR) and UV–Vis analysis. The technique of weight loss, potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS) has also been used to investigate the prevention of carbon steel corrosion in 1M HCl. The results showed that the efficiency of restraint increased when the concentration of ZnO-NPs was raised to 91% and that the inhibition efficiency is still high despite its decrease at high temperature, and it acts as a mixed-type inhibitor A sample of carbon steel with the protective inhibitor layer on top was immersed for 20 hours and observed; an increase in the charge transfer resistance (Rct) and stability of the inhibitor was noticed after 6 hours. Adsorption isotherm models demonstrated that the inhibitor adsorption mechanism on the carbon steel surface followed Langmuir, more than Freundlich and Temkin, behavior. The thermodynamic parameters showed that the adsorption process is a mixed adsorption, spontaneous, and exothermic. The results illustrated that the acid medium was a strong inhibitor of carbon steel corrosion. Scanning electron microscope (SEM) showed that the ZnO-NPs formed a good protective film on the carbon steel surface.

Silicon carbide particle-reinforced aluminum matrix (SiCp/Al) composites are significant lightweight metal matrix composites extensively utilized in precision instruments and aerospace sectors. Nevertheless, the inclusion of rigid SiC particles exacerbates tool wear in mechanical machining, resulting in a decline in the quality of surface finish. This work undertakes a comprehensive investigation into the problem of tool wear in SiCp/Al composite materials throughout the machining process. Initially, a comprehensive investigation was conducted to analyze the effects of cutting velocity vc, feed per tooth fz, milling depth ap, and milling width ae on tool wear during high-speed milling under SCCO2-MQL (Supercritical Carbon Dioxide Minimum Quantity Lubrication) ultrasonic vibration conditions. Furthermore, a prediction model for tool wear was developed by employing the orthogonal test method and multiple linear regression. The model's relevance and accuracy were confirmed using F-tests and t-tests. Ultimately, through the utilization of a genetic algorithm, the milling parameters were optimized, resulting in the identification of the most optimal combination of parameters. Empirical findings suggest that the careful selection of milling parameters can significantly mitigate tool wear, extend the lifespan of the tool, and enhance the quality of the surface. This work serves as a significant point of reference for the processing of SiCp/Al composite materials.

A new class of nano-cube core-shell heterostructures containing Ag coating on the top of WO₃ was fabricated. Physical vapor deposition was used to produce WO₃ based nano-heterostructures. All kind of wet toxic chemical process was avoided to make the process simple and contaminant free. Sputtering of WO₃ and a subsequent thermal annealing process was done to create nano-cubes of WO₃. After that, sputtering of Ag was performed to form the Ag-WO₃ core-shell nano-heterostructures (CSNH). The CSNHs were characterized using field emission scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), X-ray diffraction analysis (XRD) and UV-vis spectroscopy. The morphologies, elemental analysis, interfaces, crystallinity, phases, and chemical compositions were analyzed. The bottom-up growth of WO₃ nanocubes was studied using different time periods at 900°C. Ag coating was also studied before and after annealing. Finally, an optical property (band gap) was also analyzed using Tauc plot derive from absorption spectra. The tailoring the band gap of WO₃ from ~2.9eV to ~ 2.45 eV was observed while Ag-WO₃ CSNH formed.

Fe-(9, 19, 28, 37)wt.% Cr alloys were corroded at 700 and 800 ^oC for 70 h under 1 atm of N₂, 1 atm of N₂/3.2%H₂O-mixed gas, and 1 atm of N₂/3.1%H₂O/2.42%H₂S-mixed gas. The corrosion rate of Fe-9Cr alloy increased with the addition of H₂O, and furthermore with the addition of H₂S in N₂ gas. Fe-9Cr alloy was always nonprotective. In contrast, Fe-(19, 28, 37) wt.%Cr alloys were protective in N₂ and N₂/H₂O-mixed gas because of formation of the Cr₂O₃ layer. They were, however, nonprotective in N₂/H₂O/H₂S-mixed gas because sulfidation dominated to form the outer FeS layer and the inner Cr₂S₃ layer containing some FeCr₂S₄.

The objective of this research was to explore the impact of a gradual replacement of Ca2+ with Mn1+ on the crystal structure of CaHPO4·2H2O, which could be beneficial for producing Ca1−xMnxHPO4·nH2O compounds. In order to prepare the starting solutions required for this study, Ca(NO3) 2·4H2O, (NH4)·2HPO4, and MnNO3·4H2O were used at various molar concentrations. The findings reveal that Mn substitutes Ca partly at low Mn/Ca molar ratios, and Mn doping reduces the unit cell of CaHPO4·2H2O. The produced biphasic compound was composed of monoclinic CaHPO4·2H2O and triclinic/monoclinic nanostructured Mn3PO4O11 after a continuous increase in the Mn/Ca molar ratio to 1. When the Ca/Mn molar ratio is 1.5, a triphasic compound of monoclinic CaHPO4·2H2O, triclinic Mn3P4O11, and Orthorhombic MnHPO4·(H2O)3 phases is formed. The formation of the monophasic MnHPO4·(H2O)3 compound was achieved by increasing the Mn/Ca molar ratio above 4. By adjusting the Mn/Ca molar ratio in the initial solutions, it is possible to produce biomaterials with specific and bespoke characteristics in the future. The Mn/Ca ratio of the starting solution can be modified to produce Ca1-xMnxHPO4-nH2O phases with weight percent compositions, as established. For the first time, Ca1−xMnxHPO4·nH2O compounds were synthesized using novel methods in this manuscript.

Q345 steel is widely used in the construction industry, vehicle manufacturing industry, bridge construction industry and many other aspects due to its excellent comprehensive performance. However, due to its high silicon content, direct hot-dip galvanizing will lead to a series of problems, such as easy peeling of the coating due to the "silicon reactivity". In this paper, we adopt the "two-step hot-dipping method", first hot-dip aluminizing and then hot-dip galvanizing, to isolate the substrate and zinc liquid direct contact, so as to avoid the occurrence of "silicon reactivity". Through the microstructure characterization, neutral salt spray corrosion experiments, electrochemical experiments, the results show that: Al-Zn composite coatings from the inside out were perpendicular to the substrate growth of loose Fe2Al5 layer and Al-Zn layer, outbursts generation; Al-Zn composite coatings resistance to neutral salt spray corrosion was far more than the substrate; Al-Zn composite coatings polarization curve corrosion potential than the substrate was lower than that of the substrate by 0.512V, showing a strong corrosion resistance. It shows extremely strong corrosion resistance.

In the era of mounting water scarcity, particularly in arid regions, the agricultural sector is striving to optimize the water resource management practices. Treated wastewater (TWW) has emerged as a viable alternative to freshwater for irrigation, offering a sustainable solution to water conservation. However, ensuring the safety and quality of TWW is paramount to safeguard for both crop health and environmental integrity. Electrical conductivity (EC), a critical factor in assessing TWW suitability for irrigation, can significantly impact crop yields and soil health since it is directly linked to the concentration of dissolved salts and ions. Therefore, this study delves into the development of advanced predictive models for EC assessment by employing supervised machine learning (ML) techniques like the Support Vector Regression (SVR), Adaptive Network-based Fuzzy Inference System (ANFIS), and Multiple Linear Regression (MLR). The TWW samples collected from Al-Qatif area, Saudi Arabia were assessed in the lab through a sensor-based real-time monitoring system integrated with Internet of Things (IoT) network and a multiprobe device. The key water quality parameters assessed involved, temperature (T), pH, Oxidation Reduction Potential (ORP), Resistivity (RES), Total Dissolved Solids (TDS), Salinity and Turbidity which served as the foundation for these models, given their profound influence on and their anticipated impact on EC levels. Following feature selection, two distinct model combinations were identified for the SVR, ANFIS and MLR models. Furthermore, to evaluate prediction performance, four statistical criteria, including coefficient of determination (R²), correlation coefficient (R), mean square error (MSE), and root mean square error (RMSE), were employed. Overall, the comparative performance results proved that ANFIS-M2 indicated the strongest predictive capability with the R² value of 0.99572 and 0.75145 and the RMSE values of 0.00965 and 0.01134, respectively in both calibration and verification stages.

Peste des Petits Ruminants (PPR) is one of the major transboundary animal diseases that severely impact livestock production and trade worldwide. An investigation was carried into the seroprevalence and risk factors of PPR in small ruminants, camels, and wild ruminants in Bahrain. A total of 1240 serum samples were collected from 119 sheep flocks and 1224 serum samples from 125 goat herds. In addition, 100 sera from camels and 38 sera from wild ruminants, were collected. Serum samples were tested for the presence of PPR specific antibodies using a competitive ELISA. Flock management and health information of the flocks and herds were collected using a semi-structured questionnaire. The individual prevalence of PPR in sheep and goats was 26% and 25.5%, respectively. The flock or herd level prevalence of PPR was 22.7% and 29.6% in sheep and goats, respectively. None of the tested camels or wild ruminants were positive for PPR-specific antibodies. Sheep and goats from the Northern governorate were more likely to be seropositive to PPR than in other governorates. On the individual animal level, the univariate analysis suggested; age (<12 months), sex (male), and health status (weak animals) as risk factors for PPR seropositivity. On the flock/herd level, the multivariable logistic regression analysis identified large flock/herd size and semi-intensive farming as risk factors for PPR seropositivity.

The research presented in the article is devoted to the study of the influence of phase compounds on the friability of the Fe-Si-Mn-Al complex alloy. The urgency of the problem lies in the development of technology for producing a non-scatterable alloy from manganese-containing ores and high-ash coals. The main goal of the work is to determine the range of alloy compositions and the resulting phases that affect the dispersibility of the alloy, which is critically important for its industrial implementation. Research methods include thermodynamic diagram analysis (TDA) using data on the standard enthalpy of formation of intermetallic compounds, as well as experimental tests in an ore-thermal electric furnace with a capacity of 200 kV*A. The results show that Fe-Si-Mn-Al complex alloys form a variety of silicide and aluminide phases, including intermetallic compounds and ternary systems, which is critical for understanding and controlling their physicochemical properties. When smelting a complex alloy, the content of leboite (Fe3Si7) in the Fe-Si-Mn-Al system plays a significant role. The development of smelting technology will be aimed at avoiding the FeSi2-Fe3Si7-F2(FeAl3Si2)-Mn11Si19 tetrahedron area. This approach to controlling the composition of a complex alloy is critical to ensuring its consistent friability properties in industrial applications. Thus, this work represents an important step in understanding the physical properties and stability of Fe-Si-Mn-Al complex alloys, which have potential for widespread use in metallurgical and other industrial applications.

κ Draconis is a binary system with a classical Be star as the primary component. Its emission-line spectrum consists of hydrogen lines, notably the Hα line with a peak intensity ratio (V/R) variations phase-locked with the orbital period P = 61.55 days. Among binaries demonstrating the Be phenomenon, κ Dra stands out as one of a few systems with a discernible mass of its secondary component. Based on more than 200 spectra obtained in 2014 − 2023, we verified the physical parameters and constructed the mass function. We used part of these data obtained in 2014 − 2021 to investigate regions in the circumstellar disk of the primary component that emit the Hα line using the Doppler tomography method. The results show that the disk has a non-uniform density distribution with a prominent enhancement at Vy≈ 99 km s−1 and Vx≈−6 km s−1 that corresponds to a cloud-like source of the double-peaked Hα line profile. We argue that this enhancement’s motion is responsible for the periodic variations of the Hα V/R ratio, which is synchronised in orbital phase with the radial velocity (RV) of absorption lines from the atmosphere of the primary component.

This paper investigates the influence of magnetic field for a two dimensional deformations on a two temperature problem at the free surface of a semi-infinite semiconducting medium under the effect of mechanical force during a photothermal theory and the effect of hydrostatic initial stress on the medium. The Harmonic Wave Method (Normal Mode Analysis) has been used to obtain the equations of elastic waves, heat conduction equation, quasi-static electric field, carrier density, two temperature coefficient, ratios, and constitutive relationships for the thermo-magnetic-electric medium. The effects of several parameters as thermoelastic and thermoelectric coupling parameters and two temperature parameter of this force on the displacement component, force stress, carrier density and temperature distribution has been depicted graphically.

This study aimed to investigate the fatigue performance and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar lap joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Furthermore, the fatigue life of the 14 kV joints was one order of magnitude higher compared to the 12 kV joints. SEM observation of the fatigue fracture surface revealed the presence of typical "tire-mark" fatigue striations only in the 14 kV joint, indicating higher ductility and the ability to withstand extended plastic deformation. Notably, ultra-fine nanocrystalline Al2Cu phase, amorphous phase, and numerous dislocations hindered EBSD acquisition in the transition zone. Nevertheless, dense low-angle grain boundaries (LAGBs) and refined grains were examined at the bonding interface. This suggests that the high-velocity collision caused severe plastic deformation and led to the formation of substructures. The interfacial strength was attributed not only to the "wave-like" or "inverted hook-like" diffusion layer but also to the presence of refined grains along the interface and nanocrystalline Al2Cu in the transition zone. Furthermore, the hybrid nanocrystalline-amorphous microstructure strengthened the joint by regulating the balance between strength and ductility.

Background: Despite their generally favorable prognosis, hepatic fibrosis remains a possible complication for hepatitis B virus (HBV) inactive carriers. This study aimed to estimate the prevalence of significant fibrosis and associated risk factors among Omani HBV inactive carriers. Methods: A retrospective study was conducted of 200 Omani HBV inactive carriers visiting a tertiary hospital in Muscat, Oman, between January 2017 and December 2018. Significant fibrosis (stage F2 or higher) was identified using two-dimensional shear-wave elastography. Baseline clinical, laboratory, and radiological data were analyzed to determine associations. Results: Of the total sample, 106 patients (53%) were male, and the mean age was 44.6 ± 9.3 years. The prevalence of significant fibrosis was 20% (n = 40). Male gender (p = 0.007), age ≥60 years (p = 0.024), and fatty changes in liver ultrasound (p = 0.044) were found to be independent factors for significant fibrosis. Conclusion: the prevalence of significant fibrosis was relatively high among a sample of Omani HBV inactive carriers, with several sociodemographic and clinical risk factors identified. Periodic assessment of liver function is needed for patients with these risk factors; moreover, routine biochemical parameters could be useful predictors of disease prognosis. Further research is recommended to substantiate these findings.

The paper delineates the developed vision system of the UR5 cobot and the operating algorithm of the robotic quality control station. The hardware-software architecture of the developed robotic station was shown, consisting of a UR5 cobot equipped with a web camera and a stationary industrial camera with a lighting system. Image processing and analysis algorithms were described, the method of control and communication between the station components was discussed, and two operating scenarios were presented as a single robotic station and a robotic line. Based on the results obtained, the level of measurement noise, accuracy, and repeatability of the developed vision system were estimated.

Contamination in coastal regions attributed to fluoride and nitrate cannot be disregarded, given the substantial environmental and public health issues they present worldwide. Maintaining water quality is crucial for environmental well-being. This comprehensive study was performed to assess the spatial as well as indexical water quality, identify contamination sources, and evaluate associated health risks pertaining to nitrate and flouride in AlHassa region, KSA. The physiochemical results revealed a pervasive pollution of the overall groundwater. The dominant water type was Na-Cl, indicating saltwater intrusion and reverse ion exchange impact. Spatiotemporal variations in physicochemical properties suggest diverse hydrochemical mechanisms, with geogenic factors primarily influencing groundwater chemistry. The groundwater pollution index varied between 0.8426 and 4.7172, classifying samples as moderately to very highly polluted. Similarly, the synthetic pollution index (in the range of 0.5021-4.0715) revealed that none of the samples had excellent water quality, with various degrees of pollution categories. Nitrate Health Quotient (HQ) values indicated chronic human health risks ranging from low to severe, with newborns being the most vulnerable. Household use of nitrate-rich groundwater for showering and cleaning did not pose significant health risks. Fluoride HQ decreased with age, and children faced the highest risk of fluorosis. The Hazard Index (HI) yielded moderate to high-risk values. Nitrate risks were 1.21 times higher than fluoride risks, as per average HI assessment. All samples fell into the vulnerable category based on the Total Hazard Index (THI), with 88.89% classified as very high risk. This research provides valuable insights into groundwater quality, guiding water authorities, inhabitants, and researchers in identifying safe water sources and vulnerable human populations. The results highlight the need for appropriate treatment techniques and long-term coastal groundwater management plans.

Generative artificial intelligence tools are flourishing across various sciences, particularly in the educational domain. ChatGPT, with its versions 3.5 and 4.0, stands out for its multilingual capabilities, catering to both students and educators. This research aimed to evaluate the performance differences between these versions, and importantly, to compare the accuracy of ChatGPT's responses in English versus Arabic. In our study, we presented ChatGPT with 39 chemistry problems related to 6th-7th grade curriculum, including twenty-five open questions and fourteen multiple-choice questions. Each response was categorized as accurate, partially accurate, or inaccurate. Our analysis, focused on trends across versions and languages, revealed significant enhancements in version 4.0, particularly in its ability to process Arabic. However, despite these improvements, our findings indicate that responses in English consistently outperformed those in Arabic in terms of accuracy. In light of this discrepancy, we suggest that ChatGPT either incorporates additional Arabic databases into its training regimen or develops a code that adopts the following strategy to ensure more accurate responses in science education: questions should first be translated from Arabic to English, addressed, and then retranslated into Arabic before being presented to the user. This approach takes advantage of the greater accuracy of responses in English to benefit Arabic-speaking users, and it may also improve outcomes for speakers of other languages who experience less precise answers in the fields of chemistry or science education.

This article delves into the enduring relevance of Liberal International Relations (IR) Theory amidst persistent criticisms regarding power dynamics and its applicability in emerging states. Despite its detractors, Liberal IR Theory offers a nuanced understanding of state behavior, blending social contexts with power dynamics. It recognizes the intricacies of economic interdependence and advocates for a balanced approach in advancing democracy and human rights. While nationalism poses challenges to international institutions, their adaptability endures. Leaders, albeit constrained, retain the capacity to foster peace through visionary leadership and global cooperation. By acknowledging its limitations and fostering open dialogue, Liberal IR Theory continues to evolve, poised to contribute to a just and peaceful global order.

Present worldwide difficulties in healthcare and the environment have motivated the investigation and research of novel materials in an effort to find novel techniques to address the current chal-lenges and requirements. In particular, the use of nanomaterials has demonstrated a significant promise in the fight against bacterial infections and the problem of antibiotic resistance. Metal na-noparticles and carbon-based nanomaterials in particular have been highlighted for their excep-tional abilities to inhibit many types of bacteria and pathogens. In order for these materials to be as effective as possible, synthetic techniques are crucial. Therefore, in this review article, we high-light some recent developments in the design and synthesis of various nanomaterials, including metal nanoparticles (e.g., Ag, Zn, or Cu), metal hybrid nanomaterials, and the synthesis of mul-ti-metallic hybrid nanostructured materials. Following that, examples of these materials’ applica-tions in antimicrobial performance targeted at eradicating multi-drug resistant bacteria, material protection such as microbiologically influenced corrosion (MIC), or additives in construction ma-terials have been described.

In order to establish the formation patterns of the Co–Mg oxide system, samples with different Co:Mg ratios and heat treatment temperatures were synthesized and studied. Study of the sam-ples confirmed the phase transition of MgxCo2–xO4 spinels into corresponding solid solutions at 800–900 °C. The similarity of formation patterns for different compositions is shown. The rock-salt oxide in low-temperature samples is an anion-modified paracrystalline phase that forms a “true” solid solution only upon spinel decomposition. TPR profiles of decomposed Co3O4 spinel show surface Co3O4 peaks and a wide peak corresponding to well-crystallized CoO, while par-tial Co3O4 TPR up to 380 °C results in dispersed and amorphous CoO. High-temperature non-stoichiometric samples are poorly reduced, indicating their low oxygen reactivity. Spinel reoxidation after heat treatment to 1100 °C by calcination at 750 °C showed complete regenera-tion for MgCo2O4–Co3O4 samples and its absence in case of an excess of MgO relative to stoi-chiometry. Based on the data obtained, it can be concluded that the processes governing the formation of Co–Mg oxide systems are determined by both Co:Mg ratio and the heat treatment conditions, potentially providing the possibility of fine tuning for specific catalytic processes.

Salmonella Typhimurium is a typical Gram-Negative bacterium associated with food-borne illness threatening public health. This pathogen is reported to have caused millions of infections and thousands of hospitalizations yearly in the United States alone. Salmonella Typhimurium has a sophisticated array of virulent factors, including its flagella, which contributes significantly to its pathogenicity. Cannabidiol (CBD), the non-psychoactive component of the cannabis plant, has attracted the interest of many researchers recently because of its antimicrobial properties. With the growing interest in exploring CBD’s antimicrobial properties, we, in this study, have delved into unravelling how prolonged exposure of Salmonella Typhimurium to CBD influences the expression of the flgA gene. We hypothesized that the exposure of Salmonella Typhimurium to CBD may result in flgA upregulation, causing the bacteria to withstand various stresses and potentially enhance its survival rates and pathogenicity. We have employed several assays, such as mRNA expression, motility assays, pH induction assays, nutrient starvation interventions, and biofilm analysis, to explore the influence of CBD on the pathophysiology of Salmonella Typhimurium. Our findings reveal that CBD-resistant strains exhibit enhanced resilience to extreme pH levels and motility and survive poorly under nutrient starvation, with more robust biofilm formation compared to the susceptible strains. The results contribute to the broader comprehension of CBD resistance mechanisms in bacteria. This work provides insight into the potential therapeutic interventions for controlling CBD-resistant bacterial infections. This study also underscores the essence of exploring novel alternative antimicrobial agents to tackle the ever-persistence of bacterial antibiotic resistance.

Governments worldwide are actively committed to achieving their carbon emission reduction targets, and one avenue under exploration is harnessing the potential of hydrogen. Blending hydrogen with natural gas is emerging as a promising strategy to reduce carbon emissions, as it burns cleanly without emitting carbon dioxide. This blending could significantly contribute to emissions reduction in both residential and commercial settings. However, a critical challenge associated with this approach is the potential for Hydrogen Embrittlement (HE), a phenomenon wherein the mechanical properties of pipe steels degrade due to the infiltration of hydrogen atoms into the metal lattice structure. This can result in sudden and sever failures when the steel is subjected to mechanical stress. To effectively implement hydrogen-natural gas blending, it is imperative to gain a comprehensive understanding of how hydrogen affects the integrity of pipe steel. This necessitates the development of robust experimental methodologies capable of monitoring the presence and impact of hydrogen within the microstructures of steel. Key techniques employed for this assessment include microscopic observation, hydrogen permeation tests, and tensile and fatigue testing. In this study, samples from two distinct types of pipeline steels used in the natural gas distribution network underwent rigorous examination. To induce hydrogen absorption, an electrochemical charging process is employed in a solution rich in H+ ions. This charging process, accomplished by a potentiostat applying a constant current, prompts the hydrogen evolution reaction at the steel specimen, acting as the cathode of the charging cell. Immediate tensile and fatigue testing following the charging process enables the evaluation of mechanical properties in comparison to non-charged samples. Different charging current densities are employed to simulate various hydrogen blend scenarios. The findings from this research indicate that charged samples exhibit a discernible decline in fatigue and tensile properties. This deterioration is attributed to embrittlement and reduced ductility stemming from the infiltration of hydrogen into the steel matrix. The extent of degradation in fatigue properties is correlated not only to the hydrogen content but also to the hydrogen permeability and diffusion rate influenced by steel’s microstructural features, with higher charging current densities indicating a more significant presence of hydrogen in the natural gas pipeline blend.

The corrosion behavior of Fe-containing directionally solidified (DS) and centrifugally cast (CC) Al-Si-Cu-Zn alloys with either Co or Ni additions has been investigated. Electrochemical and immersion corrosion methods were used to investigate the corrosion behavior in 0.6 M NaCl after short (1-hour) and long (30-day) exposure periods. The employed solidification methods allowed the production of samples with a wide range of secondary dendrite arm spacing (SDAS) while preserving Si and Fe-containing phases. The 0.5 wt.% Ni and Co additions led to the growth of the AlFeSi(Ni) and AlFeSi(Co) phases, but no binary AlNi nor AlCo intermetallic par-ticles have been generated. Potentiodynamic polarization studies at early exposure revealed an increase in the corrosion potential as the Ni was added for either fast or slow solidified samples. The electrochemical impedance spectroscopy at early exposure demonstrated that the Ni-modified alloy, on the other hand, was associated to smaller charge transfer resistances, in-dicating a reduction in corrosion resistance after short elapsed time into the electrolyte. Howev-er, 30-day immersion tests revealed much lower corrosion rate of the Ni-modified alloy than the other alloys, while the corrosion rates of the Co-modified and non-modified alloys were simi-lar. In the Ni-containing alloy, decreased corrosion rate under long-term corrosion process was attributed to the formation of a thick and dense alumina layer, effectively protecting the surface under such conditions. This work contributes to a better knowledge of the corrosion behavior of Ni- and Co-corrected Al industrial scrap compositions.

Fractional cointegration in time series data has been explored by several authors, but panel data applications have been largely neglected. A previous study of ours discovered that the Chen and Hurvich fractional cointegration test for time series was fairly robust to a moderate degree of heterogeneity across sections, out of the six tests considered. Therefore, this paper advances a customized version of the Chen and Hurvich methodology to detect cointegrating connections in panels with unobserved fixed effects. Specifically, we develop a test statistic that accommodates variation in the long-term cointegrating vectors and fractional cointegration parameters across observational units. The behaviour of our proposed test is examined through extensive Monte Carlo experiments under various data generating processes and circumstances. The findings reveal that our modified test performs quite well comparatively and can successfully identify fractional cointegrating relationships in panels even in the presence of idiosyncratic disturbances unique to each cross-sectional unit. Furthermore, the proposed modified test procedure established the presence of long-run equilibrium between the exchange rate and labour wage of 36 countries agricultural markets.

Modern building automation systems implement plenty of advanced control and monitoring functions considering various parameters like users’ activity, lighting, temperature changes etc. Moreover, new solutions based on Internet of Things and cloud services are also being developed for smart buildings to ensure comfort of use, user safety, energy efficiency improvements and integration with smart grids and smart city platforms. Such a wide spectrum of technologies and functions requires a new approach in building automation systems design to provide effective way of their implementation and flexibility during operation. At the same time, in the building design and operation industries, tools based on building information modeling and digital twins are being developed. In this paper, the authors discuss development directions and application areas of these solutions, identifying new trends and possibilities of their use in smart homes and buildings. In particular, the focus is on procedures for selecting automation functions, effective integration, and interoperability of building management systems with Internet of Things considering organization of prediction mechanisms and dynamic functional changes in buildings and smart networks. Chosen solutions and functions should consider the requirements from EN ISO 52120 standard and the guidelines defined for the Smart Readiness Indicator.

This review paper aims to understand the current processing plant maintenance systems and further identify on-stream phased array corrosion mapping (PACM) to reduce turnaround maintenance (TAM) activity during plant operations. Reducing the TAM duration and extending the TAM interval are common goals of most researchers. Thus, a detailed review was performed to understand the maintenance systems and the problems faced. Furthermore, a review of the current PACM application and the possibility of applying it during on-stream inspection was also per-formed. PACM has better detectability for localized corrosion, and the results can be obtained for a range of thicknesses, which is the main advantage of this method. The challenge is to apply it to a surface with high temperatures, owing to the greater probe contact and the limitation of ultrasonic properties. This literature review provides a more precise direction for future research to evaluate PACM on piping that can be utilized in inspection during plant operation at elevated temperatures. Detecting and monitoring corrosion growth without shutdown.

This paper presents the deformation of the joined sheet after the clinch-riveting process. The DX51D steel sheet with zinc coating was used. The samples to be joined with clinch riveting technology had a thickness of 1±0.05 mm and 1.5±0.1 mm. The sheet deformation was measured before and after the joining process. The rivet was pressed in the sheets with the same dimension between the rivet axis and three sheet edges: 20, 30 and 40 mm. For fixed segments of the die, from the rivet side close to the rivet, the sheet deformation was greater than that of the area with movable segments. The movement of die sliding element caused more sheet material to flow in the space between the fixed part of the die and movable segments. Hence, the sheet deformation in these places was smaller than for the die fixed element – sheet material was less compressed. For sheets thickness 1.5 mm and width 20 mm, the bulk of the sheet was observed. For a sheets width of 20 mm, it was observed that the deformation of the upper and lower sheets in the area of the rivet is greater than for sheets width of 30 or 40 mm.

The leaves of Nicotiana glauca (Solanaceae) plant, are known for its major cause of health concern. This study investigated the antioxidant activity and polyphenols composition of aerial parts of N.glauca collected from its wild habitat in Jordan, using Methanol-Conventional (MC) and deep eutectic solvents (DESs) extraction methods in addition to nicotine content determination using UHPLC. The results have shown that the MC extract contains fewer total phenols and flavonoid content than the DES extract at ratio of 90% (0.1194 ±0.009 and 0.311± 0.020 mg/mL equivalent to gallic acid) and (0.01084±0.005 and 0.928 ± 0.09 mg/mL equivalent to rutin), respectively. Moreover, the study showed that the MC extract contains 635.07 ppm nicotine compared to the DES extraction method, which contains 1194.91 ppm. Both the MC and the DES extracts exhibited weak antioxidant activities with the highest was 33%inhibition equivalent to ascorbic acid was found for DES at (90%) ratio. The UHPLC-MS/MS analysis revealed the presence of variations in the detected compounds between the two extraction methods used. This study found that en-vironmentally friendly DES extraction of N. glauca produced higher phenol and flavonoid content than MC method, highlighting green chemistry methods' superior efficiency and environmental benefits for extracting valuable phytoconstituents.

High dimensional datasets are highly likely to have redundant, irrelevant, and noisy features that negatively affect the performance of the classification algorithms. Selecting the most relevant features and reducing the dimensions of datasets by removing the undesired features is a dimensional reduction technique called Feature Selection (FS). In this paper, we propose an FS approach based on the Black Hole Algorithms (BHO) with a mutation technique called MBHO. Generally, BHO contains two major phases. At the exploitation phase, a set of stars are modified based on some rule and according to some objective function, the best star is selected as the black hole which attracts other stars. Furthermore, when a star gets closer to the event horizon, it will be swallowed and a new one will be randomly generated in the search space which thus is the exploration phase. However, randomness may cause the algorithm to fall into the trap of local optima, and to overcome such complications, inversion mutation is used. Furthermore, we modify a widely utilized objective function in most of the proposed works for wrapper feature selection by combining two new terms that are based on the correlation among the selected subset of features and the features and the classification label. We also utilize a transfer function, known as the V2 transfer function, to convert continuous values into discrete ones to enhance search. We assess our approach via extensive evaluation experiments using fourteen benchmark datasets. We benchmark the performance of a wrapper FS approach called Binary Cuckoo Search (BCS), and three filter-based FS approaches (namely Mutual Information Maximisation (MIM), Joint Mutual Information (JMI), and minimum Redundancy Maximum Relevance (mRMR)). Our evaluation has shown that the proposed model is an effective approach for FS, in selecting better features that enhance the performance metrics on the classifiers. Thus, MBHO can be utilized as one alternative to the existing state-of-art-approaches. We release the source codes of our implementation for the community to build on with new methods and datasets.

The endocannabinoid system (ECS) is a complex neuromodulatory network in the human body that have enormous impact in developing the central nervous system, as well as modulates various physiological processes. The ECS is made up of anandamide, 2-arachidonoylglycerol (2-AG), which are responsible for the synthesis and degradation of endocannabinoids, and enzymes such as FAAH and MAGL ensures the precise control over endocannabinoid levels. The ECS relies on CB1 receptors found in the central nervous system (CNS), and CB2 receptors found in the peripheral nervous system and immune cells. Dysregulation of the ECS has been associated with several health conditions, prompting investigations into its association with phytocannabinoids to harness their therapeutic potential. The ECS is intricately linked with the nervous system, and it is known to modulate neuronal activities in the CNS, influencing pain and mood modulation. The ECS is also associated with neuropathies-peripheral nerve damage leading to symptoms such as weakness, numbness and pain as evidenced in diabetic neuropathy, Guillain-Barré Syndrome, carpal tunnel syndrome, peripheral neuropathy, and postherpetic neuralgia. The focus of this review is on the interplay between 2-arachidonoylglycerol and anandamide amidohydrolase in neuropathy, elucidating their roles in pain regulation, inflammation, and specific neuropathies. The knowledge generated is expected to have broad implications, providing comprehensive insights into neuropathic conditions and how to improve on them. Ultimately, this understanding may lead to more effective treatments and improved quality of life for individuals affected by these conditions.

Over the years, the need for autonomous systems such as drones, also known as unmanned aerial vehicles (UAVs), has significantly increased in popularity across several industries, including the military. The Internet of Battlefield Things (IoBT) represents a modern technological advancement that significantly enhances the operational efficacy of defense systems. It establishes an integrated military force by connecting individuals to intelligent technology in drones, radios, equipment, antennas and ground stations. This is achieved through the utilization of cloud and edge computing, sensors, mobile devices, embedded systems, and IoT-based systems. However, IoBT security is significantly compromised by enemies that exploit the vulnerabilities and malicious intrusions that specifically target the external environment or to obtain sensitive data. In addition, a comprehensive understanding of cyberattacks and countermeasures is essential for assuring the security of IoBT. On the other hand, as cyber threats get more complicated, trust becomes increasingly important for the security of digital systems. Within this context, the zero trust architecture contends that the security of a complex network is inherently vulnerable to internal and external threats. In defense, UAV security system applications, for example, the primary purpose of the zero trust architecture is to limit the vulnerability of military UAV systems to cyberattacks, hence reducing the possibility of data breaches and illegal entry. This study conducts a systematic review aimed at identifying different aspects of cybersecurity strategies for protecting UAV systems within the IoBT domain. Furthermore, zero trust architecture is presented in the study as an effective prospective solution to the security issues that develop in defense UAV systems.

Solar pasteurization, as a means of treating milk in remote rural areas without electrical power, is based on using solar energy to thermally inactivate pathogenic microorganisms at temperatures below the boiling point to maintain or improve milk quality. A solar milk pasteurizer of flat‐plate water‐heating glass acting as the solar collector, connected to a stainless-steel cylindrical milk vat, was constructed and evaluated in Navrongo, in the tropical savanna zone of Ghana, West Africa. The novel approach taken in this project is to integrate the solar collection and heat exchanger into a single unit using materials and fabrication techniques readily available in the developing world. The vat comprises a 1.5 mm thick stainless steel cylindrical tank, a 2.2 cm wide hot water jacket, and an outer layer of 5.0 mm thick aluminium foil insulation. Hot water produced by the collector was used for pasteurizing milk. The optimum quantity of milk that this device could pasteurize under the study conditions was 8 L. The device could pasteurize raw milk to a maximum temperature of 74 °C at 14:00 h GMT. The ambient temperature during the pasteurization ranged from 30 °C to 43 °C. The microbial analysis before and after the pasteurization was done, and the result shows that the total bacteria count before pasteurization was 6.6x10⁶ log CFU/mL per unit volume, and the total bacteria count after pasteurization was 1.0x10² log CFU/mL. By acceptable standards, the total bacteria count after pasteurization is within a safe range for consumption, and coliform counts were negative. The solar milk pasteurization system is cost-effective. Hence, it is appropriate for milk producers in arid pastoral areas without electricity to adopt the solar pasteurizer as an alternative to firewood as a fuel source for milk pasteurization. This approach can potentially create a cottage industry that may also play a crucial role as a water treatment technology that will improve the health of rural populations.

Use of MS Excel as a platform for teaching simple iterative solution of partial differential equations runs into issues of reliability of the computation because of the large number of calculations required. This article documents the problem and an empirical solution. The cause of this unreliability was found by detailed examination of the numerical results from three simultaneous iterations. Computers of several types from different manufacturers were found to fail occasionally in updating variables in the numerical iteration. A simple work-around is suggested and was tested on several platforms.

Sustainable development and education in sustainable development (ESD) are crucial and interconnected topics under wide discussion today. Young adults need to be educated in how to help bring about change. Thus, the dynamic relationship between school and home is important. In education, use could be made of English language classes, especially since English is a global language that enables access to the sustainability literature and facilitates discussion in global conferences and meetings. Consequently, English as a foreign language (EFL) students could gain confidence from being able to understand and use the terminology of, for example, sustainability. In this paper, the use of competence-based language teaching (CBLT) is proposed as a means of introducing sustainability topics into EFL writing classes at a university in Saudi Arabia. Students’ competence in sustainable development is therefore considered based on their ability to write about suggested sustainable development topics, measured on a scale for five dimensions of ESD proposed by Michelsen and Fischer (2017). The results demonstrate that the students possessed competence in sustainable development and intended to participate in its implementation. Thus, recommendations are made for the stakeholders in the education sector to include sustainable development topics as an initial offering in the curricula of various specialties using the CBLT approach.

The field of construction materials is pivotal in developing sustainable and resilient infrastructure. This demands continuous research to understand the properties and behaviors of these materials under diverse conditions. Although advancements in material science and numerical modeling have been significant, experimental testing remains indispensable for a thorough comprehension of material characteristics, particularly under extreme stresses and environmental factors. This need has forced the development of a wide array of testing techniques, each designed to evaluate specific engineering properties, thus creating a complex and varied landscape of experimental methodologies. This study provides a comprehensive overview of both conventional and innovative experimental testing techniques used to characterize construction materials. It explores the related methodologies and identifies potential gaps in their application within the industry. The spectrum of testing covered includes mechanical, chemical, thermal, microstructural, durability, physical, rheological properties, and non-destructive testing methods. Mechanical tests assess strength, hardness, and fatigue, whereas chemical analyses utilize techniques such as spectroscopy and chromatography. Thermal properties are examined using thermogravimetric analysis, and microstructural characteristics are explored through advanced imaging techniques. Durability testing focuses on materials’ resistance to environmental challenges, while physical properties tests evaluate aspects like porosity and water absorption. Rheological and non-destructive tests further examine materials’ behavior and integrity without causing damage. By discussing these methodologies, the study sheds light on various approaches to material evaluation and aims to enhance the selection, application, and development of testing standards. This overview seeks to inform and inspire future research and innovation in the science of construction materials, contributing to the development of more resilient and sustainable construction practices.

In this paper, several classes of rough Marcinkiewicz integral operators along surfaces of revolution on product spaces are investigated. We prove the Lp boundedness of these operators when their kernels functions belong to a class of functions related to a class of functions introduced by Grafakos-Stefanov. The results in this paper extend and improve several known results on Marcinkiewicz integrals.

This paper aims to study and analyze the effect of the flow rate and amplitude of walling waves on the peristaltic flow of Jeffrey’s fluid through an irregular channel. In addition, it analyses streamlined patterns and their local and global bifurcation flow. The theory of dynamical systems is used to explore the position of critical points and their bifurcation. Numerical and analytical methods are presented to display effective changes in amplitude and rate of the flow on the transport of fluid. Three types of streamline patterns occur backward, trapping and augmented flow in the channel through movement due to changes in the value rate parameters.

Asymptotic theories for fractional cointegrations have been extensively studied in the context of time series data, with numerous empirical studies and tests developed. However, most of the previously developed testing procedures for fractional cointegration were primarily designed for time series data. This paper proposes a generalized residual-based test for fractionally cointegrated panels with fixed effects. The test development is based on bivariate panel series with the regressor assumed to be fixed across cross-sectional units. The proposed test procedure accommodates any integration order between [0,1], and it is asymptotically normal under the null hypothesis. Monte Carlo experiments demonstrate that the test exhibits better size and power compared to a similar residual-based test across varying sample sizes.

In this paper we introduce the Adomian decomposition method for a class of first order fuzzy dynamic equations on arbitrary time scales for existence of solutions. The results are provided with suitable numerical examples.

Cloud data centers play a vital role in modern computing infrastructure, offering scalable resources for diverse applications. However, managing costs and resources efficiently in these centers has become a crucial concern due to the exponential growth of cloud computing. User applications exhibit complex behavior, leading to fluctuations in system performance and increased power usage. To tackle these obstacles, we propose the consolidation of virtual machines (VMs) to optimize resource utilization and reduce operational costs. This paper introduces a novel algorithm, leveraging the Modified Artificial Feeding Birds Algorithm (ModAFBA), to manage cost optimally in cloud data centers by reducing power usage while meeting service level agreements (SLAs). The ModAFBA algorithm, inspired by bird foraging behavior, dynamically adjusts solutions based on environmental changes. Comprehensive experimental evaluation demonstrates the superiority of the proposed algorithm in terms of power usage, migration count, and SLA compliance. Through this research, we aim to advance cost management and resource optimization in cloud data centers, providing a valuable tool for cloud service providers to enhance infrastructure efficiency and achieve cost savings.

Microbial composition across substrates in mangroves, particularly in the Middle East, remains unclear. This study characterized bacterial communities in sediment, water, Terebralia palustris snail guts, and plastic associated with Avicennia marina mangrove forests in two coastal lagoons in the Sea of Oman using 16S rDNA gene MiSeq sequencing. The genus Vibrio dominated all substrates except water, which featured unique genera Sunxiuqinia and Pseudomonas. There were significant differences in bacterial communities on different substrata, in particular plastic. Snail guts harbored the highest number of unique Operational Taxonomic Units (OTUs) in both lagoons. Plastic in the polluted Sawadi lagoon with low salinity harbored distinct genera like Vibrio, Aestuariibacter, Zunongwangia, and Jeotgalibacillus absent in Qurum lagoon with higher salinity and low pollution. Sawadi lagoon exhibited higher species diversity in sediment and plastic substrates, Qurum lagoon demonstrated lower overall species diversity. The PCA indicates that environmental factors like salinity, pH, and nutrient levels significantly influence bacterial community composition across substrates. Variations in organic matter and potential anthropogenic influences, particularly from plastics, further shape bacterial communities. This study highlights the complex microbial communities in mangrove ecosystems, emphasizing the importance of considering multiple substrates in mangrove microbial ecology studies.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

The period of the COVID-19 pandemic resulted in a rapid development of innovative education methods, in particular using e-learning and remote work tools. The effects of this development are also post-pandemic changes in formal teaching regulations, in particular in higher education, allowing classes and lectures to be carried out with Blended Learning or Flipped Classroom methods. This paper provides information about a case study of implementing ICT technologies with elements of the mentioned methods in one of the subjects at a technical university. The implemented tools and solutions in the field of e-learning and interactivity are presented, along with information regarding their perception by students during two academic years in the post-COVID-19 period. The analysis of results of these information and student evaluations indicates their generally positive approach to such innovations in the educational path, and at the same time shows significant challenges for teachers to increase the attractiveness and effectiveness of the teaching process and the development of practical, technical skills of students.

The corrosion inhibition behavior of cetyl pyridinium chloride (CPC) on mild steel (MS) in 0.5 M H₂SO₄ solution was examined using the weight loss method and potentiodynamic polarization method. The experimented MS surface was characterized by Fourier Transform Infrared Spectroscopy (FTIR), Field Emission Scanning Electron Microscopy (FESEM), and Atomic Force Microscopy (AFM). Corrosion rate and corrosion efficiency was calsulated via weight loss and potentiodynamic polarization methods where the corrosion rate in 0.5 M H₂SO₄ , 0.000192 M, and 0.0077 M of CPC solution was 12.09×10^-3, 8.23×10^-3, 6.63×10^-5 (mm/Year), respectively and the inhibition efficiency of 94.42% and 98.54%. FESEM studies demonstrated the corrosion attack on MS surface. Also, the EDX showed the presence of nitrogen of CPC. Thus, CPC acts as an important corrosion inhibitor.

The mechanism of ciprofloxacin action involves interference with transcription and replication of bacterial DNA, which results in elevated oxidative stress, and bacterial cell death. Vorinostat was shown to induce oxidative DNA damage. In the current work, the possibility for interactive effect of vorinotat on ciprofloxacin-induced cytotoxicity against a number of reference bacteria was investigated. Standard bacterial strains were Escherichia coli ATCC 35218, Staphylococcus aureus ATCC29213, Pseudomonas aeruginosa ATCC 9027, Staphylococcus epidermidis ATCC 12228, Acinetobacter baumannii ATCC 17978, Proteus mirabilis ATCC 12459, Klebsiella pneumoniae ATCC 13883, methicillin-resistant Staphylococcus aureus (MRSA) (ATCC 43300), and Streptococcus pneumoniae (ATCC 25923). The antibacterial activity of ciprofloxacin with or without pretreatment of bacterial cells by vorinostat was examined using disc diffusion procedure and determination of the minimum inhibitory concentration (MIC) and zones of inhibition of bacterial growth. All tested bacterial strains showed sensitivity to ciprofloxacin. When pretreated with vorinostat, significantly larger zones of inhibition and smaller MIC values were observed in all bacterial strains compared ciprofloxacin alone. As a conclusion, current results showed the possible agonistic properties for vorinostat when it is used together with ciprofloxacin. Future research will be focus on molecular mechanisms possible for such interactive effect.

Abstract: Qatar and other Gulf States have a diverse range of marine vegetation that is adapted to the stressful environmental conditions of seawater. The industrial wastewater produced by oil and gas activities adds further detrimental conditions for marine aquatic photosynthetic organ-isms on the Qatari coastlines. Thus, these organisms experience severe stress from both seawater and industrial wastewater. This review discusses the biodiversity in seawater around Qatar, as well as remediation methods and metabolic pathways to reduce the negative impacts of heavy metals and petroleum hydrocarbons produced during these activities. These methods include phyto-stabilization phyto-accumulation, phyto-volatilization, and phyto-degradation. Phy-to-degradation in particular is discussed in detail, including metabolic pathways such as alkane and aromatic-compound degradation pathways. The role of microorganisms that are adjacent to or associated with these aquatic marine organisms is discussed, including rhizosphere biodeg-radation. In this type of biodegradation, exudates are released by plant roots and supply nutrients to microorganisms in the rhizosphere, which enhances their ability to degrade organic pollutants. Special attention is paid to mangrove forests and their roles in remediating shores polluted by industrial wastewater. Seagrasses (Halodule uninervis, Halophila ovalis, and Thalassia hemprichii) and seaweeds (Chlorophyta, Phaeophyta, and Rhodophyta) around the peninsula of Qatar are also discussed.

Hyperlipidemia case was described as a rise of lipid profile or lipoproteins in the blood. This study describe briefly investigate the reducing hyperlipideamia impact of Ginkgo biloba on the level of lipid profile.

This study finds that in northern Jordan, breeder indicators present challenges to the sustainability and growth of sheep and goat farming, while economic indicators suggest a combination of financial stability alongside hurdles related to profitability and resource ownership. Breeder age plays a role in the management of livestock herds, due to factors such as experience, resources, or adherence to traditional practices. Experience significantly affects breeders' decisions on male insemination replacements, likely due to skill. Crop cultivation influences breeders' returns by reducing feeding costs, while strategic lamb sales management boosts individual animal profitability. Winter raises animal mortality due to cold stress. Other animals in herds increase kid mortality by spreading diseases. Breeder experience significantly affects lamb survival, stressing its role in care. Increasing sheep proportion enhances lamb production and reduces lamb mortality while managing rams and selling lambs positively affects herd health and productivity. A larger goat herd proportion positively correlates with kids sold but inversely with breeding males and overall kids, implying trade-offs affecting herd productivity and mortality rates. Sheep herds (92.5%) show slightly better reproductive success than goats (90.6%), implying superior long-term viability. Flock excels in birth, survival, and sales, but low sheep and lamb%. Improvement is needed for sustainability, and the potential is high. Goat breeding shines in birth, sales, and overall success, but needs attention to kid survival and other sustainability issues. In conclusion, despite challenges, there are promising opportunities to enhance sheep and goat farming in Jordan. Effective management, informed by breeders' experience and economics, is crucial. Empowering small-scale herders and implementing targeted interventions like winter mortality solutions and selective breeding is vital for sustainable growth.

5-(4-aminophenyl )-2-amino -1,3,4-thiadiazole was prepared by reaction of Thiosemicarbazide with 4-amino benzoic acid under reflux condition for 7 hours. The compound which has been synthesized successfully was subjected to addition reaction with 4-(Dimethylamino) benzaldehyde under reflux condition for 6 hours to synthesize Schiff bases. These compounds was characterized by using FTIR) and evaluated for their anticancer activity. The effect of (1, 3, 4-thiadiazole derivative) on the activity of malignant cells was studied by using different types of cell lines [Breast cancer, and human prostate cancer]. And was used the Electron microscope to show that the effect of the derivative on the cancer cells before and after 3 days of the injection time. It was found that the Schiff base of thiadiazole-1,3,4-(Dimethylamino)benzylidineamino]- [4-2-phenyl]amino was effective in reducing the size and density of malignant cells. That of 46.7 while in breast ) 145(DUprostate for growth inhibition produce of equal 85.9 µg/ml.

Annually, more than 1.5 million preventable new hepatitis B (HBV) infections continue to occur, with an estimated global burden of 296 million individuals living with chronic hepatitis B infection. This substantial health challenge results in over 820,000 annual deaths attributed to complications such as liver cirrhosis and hepatocellular carcinoma (HCC). HBV vaccination remains the cornerstone of public health policy to prevent chronic hepatitis B and its related complications. It serves as a crucial element in the global effort to eliminate HBV, as established by the World Health Organization (WHO), with an ambitious 90% vaccination target by 2030. However, reports on global birth dose coverage reveal substantial variability, with an overall coverage rate of only 46%. This comprehensive review thoroughly examines global trends in HBV vaccination coverage, investigating the profound impact of vaccination on HBV prevalence and its consequences across diverse populations, including both high-risk and general demographics. Additionally, the review addresses the formidable challenges and facilitating factors essential for achieving WHO's HBV vaccination coverage objectives and elimination strategies in the coming decade and beyond.

Despite the effectiveness of insulin injections in managing hyperglycemia in Type 1 Diabetes, they fall short in addressing autoimmunity and regenerating damaged islets. This review aims to explore the potential of various treatment modalities for T1DM, including mesenchymal stem cells (MSCs), MSC-derived exosomes, gene therapy, islet allotransplantation, and pancreatic islet cell transplantation. Results: MSCs demonstrate efficacy in T1DM treatment through immunomodulation and tissue regeneration, although further research is warranted to optimize their therapeutic potential. Gene therapy presents a promising approach despite challenges such as donor shortage and immune rejection. Pancreatic islet cell transplantation emerges as a viable option, albeit with associated risks including graft rejection and the need for immunosuppression. Teplizumab, an FDA-approved humanized monoclonal antibody, revolutionizes the treatment landscape of Type 1 Diabetes by significantly delaying its onset, offering a paradigm shift since the discovery of insulin Conclusion: Ongoing studies and technological advancements in T1DM management offer a promising outlook for improved treatments and possibly even eradication on a global scale. MSCs, MSC-derived exosomes, gene therapy, and pancreatic islet transplantation hold considerable potential.

Background Olfactory perception is an important physiological function for the human well-being and health. Loss of olfaction, or anosmia, caused by viral infections such as severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) received a considerable attention especially in the persistent cases that take long time to recover. Objectives This review discusses the integration of different components of the olfactory epithelium to serve as a structural and functional unit, and explores how they are affected during viral infections, leading to the development of olfactory dysfunction. Methods The review mainly focused on the role of receptors mediating the disruption of olfactory signal transduction pathways such as ACE2, TMPRSS2 protease, neuropilin 1 (NRP1), basigin (CD147), olfactory, TRPV1, purinergic, and interferon gamma receptors. Furthermore, the compromised function of the epithelial sodium channel (ENaC) induced by SARS-CoV-2 infection and its contribution in olfactory dysfunction is also discussed. Results Collectively, this review provides fundamental information about the many types of receptors that may modulate olfaction and participate in olfactory dysfunction. It will help to understand the underlying pathophysiology of virus-induced anosmia which may help in finding and designing effective therapies targeting molecules involved in viral invasion and in olfaction. Conclusion This wide and complex spectrum of receptors that mediates the pathophysiology of olfactory dysfunction reflects the many ways by which anosmia can be therapeutically managed.

High pathogenicity avian influenza (HPAI) H5N1 clade 2.3.4.4b continues to have a substantial impact on wildlife, globally. A recent study has described the putative detection of HPAI in clinically healthy penguins, and those which were fitted with satellite tags reportedly engaged in apparently normal foraging behaviour in the months following sample collection. Herein we investigate the diagnostic approach utilised, and reveal that while the authors likely did detect subtype H5 influenza A virus, the most parsimonious conclusion is that they detected low pathogenicity H5 rather than HPAI H5N1. In response, we have provided an overview key considerations when selecting a diagnostic and outline published diagnostic assays that should be considered for future studies.

Batch and transport experiments were used to investigate the remediation of a loamy sand soil contaminated with Cr(VI) using zero valent iron nanoparticles (nZVI) stabilized by the carboxy methyl cellulose (CMC-nZVI). The effect of pH, ionic strength (IS), and flow rate on the removal efficiency of Cr(VI) were investigated under equilibrium (uniform transport) and non-equilibrium (Two-site sorption) transport using the Hydrus-1D model. The overall removal efficiency ranged from 70 to over 90% based on the chemical characteristics of the CMC-nZVI suspension and the transport conditions. The concentration and pH of the CMC-nZVI suspension had the most significant effect on the removal efficiency and transport of Cr(VI) in the soil. The average removal efficiency of Cr(VI) was increased from 24.1 to 75.5% when the concentration of CMC-nZVI nanoparticles was increased from 10 to 250 mg L-1, mainly because of the increased total surface area at larger particle concentration. Batch experiments showed that removal efficiency of Cr(VI) was much larger under acidic conditions. The average removal efficiency of Cr(VI) reached 90.1 and 60.5 % at pH 5 and 7, respectively. The Two-site sorption model described quite well (r2 = 0.96-0.98) the transport of Cr(VI) in soil as compared to the uniform transport model (r2 = 0.81-0.98). The average retardation of Cr(VI) was 3.51 and 1.61 at pH 5 and 7, respectively, indicating earlier arrival for the breakthrough curves and shorter time to reach maximum relative concentration at lower pH. The Hydrus-1D model has proven to be an efficient tool for assessing the removal of Cr(VI) pollutants, offering innovative, cost-effective, and environmentally friendly remediation methodologies.

Polarimetric Synthetic Aperture Radar (PolSAR) images encompass valuable information that can facilitate extensive land cover interpretation and generate diverse output products. Extracting meaningful features from PolSAR data poses challenges distinct from those encountered in optical imagery. Deep Learning (DL) methods offer effective solutions for overcoming these challenges in PolSAR feature extraction. Convolutional Neural Networks (CNNs) play a crucial role in capturing PolSAR image characteristics by leveraging kernel capabilities to consider local information and the complex-valued nature of PolSAR data. In this study, a novel three-branch fusion of complex-valued CNN named Shallow to Deep Feature Fusion Network (SDF2Net) is proposed for PolSAR image classification. To validate the performance of the proposed method, classification results are compared against multiple state-of-the-art approaches using the Airborne Synthetic Aperture Radar (AIRSAR) datasets of Flevoland, San Francisco, and ESAR Oberpfaffenhofen dataset. The results indicate that the proposed approach demonstrates improvements in OA, with 1.3% and 0.8% enhancement for the AIRSAR datasets and 0.5% improvement for the ESAR dataset. The analyses conducted on the Flevoland data underscore the effectiveness of the SDF2Net model, revealing a promising OA of 96.01% even with only 1% sampling ratio.

Herein, we examined the effects of weather parameters and individual clinicodemographic risk factors on hemorrhagic stroke (HS) incidence, severity on admission, and disability at discharge in a harsh desert climate. In a retrospective design we studied patients admitted to a stroke unit in Arab Emirates in 2016-2019. With a distributed lag nonlinear model we explored immediate and delayed effects of weather on stroke incidence. Supervised machine learning was used to build models predictive of scores in NIHSS and mRS scales. We assessed model performance by calculating ROC AUC, F1 scores, specificity, and sensitivity. HS risk increased after a significant change in any weather parameter. The risk was reduced below baseline after 1-week adjustment to environmental changes. Climate input from the previous 3 days yielded reliable classification models. Humidex was a better predictor of severity than air temperature, whereas body mass index, age, and time of day at stroke onset were the strongest clinical predictors. Weather parameters before admission were stronger predictors of disease severity than individual clinical factors. We addressed limitations of previous studies by analyzing a full set of climate parameters: ambient temperature, relative humidity, humidex, atmospheric pressure, and wind speed. Predictive models may help to optimize patient management and develop preventative strategies.

Cobalt oxide nanoparticles are promising candidates for various kinds of practical application. The interest of researchers and scientists in these nanoparticles is due to their unique physical and chemical properties such as density, melting point, magnetic characteristics and band gap. The need to develop high performance and low-cost technologies for obtaining Co3O4 nanoparticles is a major reason in research in this area. The widespread commercial use of Co3O4 nanoparticles will open doors for numerous novel cost effective technologies, which are mostly dependent on the type of synthesis method and raw materials. A possible solution to this problem is to use Cobalt nitrates as a cost-effective precursor using the solution combustion method. Solution combustion synthesis method is one of the best candidate methods that have the potential for high performance and is also cost-effective. This review examines recent progress in the synthesis of Co3O4 nanoparticles by solution combustion method and underscores their significance across various fields, highlighting the need for further research and exploration of their multifaceted applications. In addition, the most recent advancements in the applications of Co3O4 nanoparticles in sensitive sensing, catalysis, supercapacitors/batteries and water treatment/pollutants removal are reviewed and described, focusing on current trends, challenges, and future outlooks.

In this study, the olive pomace was considered because of its importance in the environment. So, this study carried out to estimate the total nitrogen content and the fatty acids profile of olive pomace. The olive pomace samples were collected from Irbid, Jarash, Ajloun and Mafraq during the harvesting season 2014 to study the biochemical characteristics of fatty acid composition and the total nitrogen (TN) content. The total nitrogen content was determined by standard Kjeldahl method and the fatty acid profile was detected by gas chromatography (GC). The results show that the total nitrogen content ranged from (0.39 ± 0.0) to (0.62 ± 0.02) with statistically significant difference suggesting that the composition of matrices and their percentage may be responsible for composition of amendments. The calculated total protein percentage ranged between (2.43 ± 0.00) to (3.87 ± 0.17). Also, 13 different fatty acids were quantitatively profiled and quantitated. Oleic acid (C 18:1) was found to be the highest percentage of all other fatty acids and ranged between (59.03%) and (63.81%), moreover the C 18:1/C 18:2 (oil quality) was calculated and C.V% showed variation meaning that nutritional implication could affect the oxidative stability of oils. In conclusion, OP by-product could give a sustainable and alternative-cheap source for fertilizers, pharmaceutical industries, cosmetics and other industries.

Food composition data in the EMR countries are often lacking, obsolete or unreliable. The study aims to provide reliable and up-to-date nutrient data of selected food products consumed in Oman in order to evaluate consistency of nutrition labelling and update the current used food composition database. Contents of total fat, fatty acids, carbohydrates, total nitrogen, sugars and sodium were chemically analyzed in 221 foods and beverages purchased in 2022 and label and corresponding laboratory values were compared using the tolerance levels of the European Union. Food items were classified according their nutritional composition, the extent of processing and coded according FoodEx2 system. Results indicate that the nutrient values stated on a label align with the values obtained in the laboratory with the exception of a 6.3% discrepancy in TFAs content, where the reported values are higher than the appropriate reference values. The category with the highest frequency (71.5%) consisted of ultra-processed foods. In terms of inconsistencies in the nutrition claims, 5.1% of food products with claims did not comply with the statement “sugar free” or “low salt”. These findings underscore the significance of vigilant monitoring of nutritional labels as a means to implement measures that promote the well-being of consumers.

This study aimed to examine the chemical makeup and antioxidant properties of hydroalcoholic extracts obtained from Lonicera japonica Thunb. Thunb. (honeysuckle) flowers collected from two geographically distinct regions of Romania: a mountainous region (Făgăraș Mountainous, Brașov) and a coastal region (Black Sea, Constanța). Our research revealed that the extracts from these two regions differed significantly in terms of their total polyphenol, flavone, and phenolic carboxylic acid content, as well as their antioxidant activity. These results suggest that climatic factors play a crucial role in shaping the phytochemical profile and antioxidant activity of Lonicera japonica Thunb. Thunb. extracts. Therefore, these findings could potentially contribute to the development of standardized herbal preparations and nutraceutical products.

Understanding the dynamics of land use and land cover (LULC) change in today's context of rapid urbanization is critical for sustainable urban planning and environmental conservation. Therefore, the research aim is to understand the LULC changes in Chattogram Metropolitan Area and to assess the policy implications of these changes for sustainable urban development. Through a comparative analysis of LULC maps for two periods (1997–2007; 2007–2017), we investigated the transformation of a detailed planning zone before and after detailed area plan (DAP) approval. Using a mixed-method approach integrating quantitative data with policy analysis, we elucidated the impacts of urbanization trends on local ecosystems—specifically the conversion of forest cover and waterscape use. The findings reveal a significant conversion of forested and waterscape areas to urban and peri-urban landscapes, highlighting the urgent need for sustainable planning interventions that focus on these peri-urban areas. The study further critiques the DAP's effectiveness, revealing a disconnect between regional policy implementation and local outcomes. This research proposes a validated, scalable framework for urban master plans that adapts to the complex socio-ecological contexts of rapidly urbanizing regions.

Rice blast is the most harmful disease caused by Magnaporthe oryzae, leading to yield loss. The aim of the work is to improve resistance of rice to blast by introducing and pyramiding genes using conventional breeding technique and modern MAS analysis. Pyramiding is the combination of several resistance genes in one genotype, in this case it improves the resistance of rice to pathogens. MAS analysis revealed that 3 out of 4 studied domestic high-yielding rice cultivars (Bakanasski, Aisaule and Aru) contain 1 blast resistance gene (Pi-2). It was discovered 7 pyramidal lines with the introduction of a combination of 2 blast resistance genes (Pi-1 and Pi-ta) into 6 hybrids and 3 genes (Pi-1, Pi-33 and Pi-ta) into 1 line. Phytopathological test of local cultivars and pyramidal lines of rice showed that 3 out of 7 pyramidal lines have moderate resistance: 2 lines (F2 Bakanasski/7667 (var. vulgaris Koern.) and F2 Aisaule/7664 (var. italica Alef.)), containing 2 resistance genes (Pi-1 and Pi-ta) and 1 line – F2 Aisaule/7689 (var. zeravschanica Brsch.), carrying 3 genes (Pi-1, Pi-33 and Pi-ta), while the local cultivars Bakanasski, Aisaule and Aru are susceptible. As a result, the blast resistance of rice was improved by creating pyramidal lines. Pyramided lines can be used for germplasm exchange and in rice breeding programs to improve blast resistance in rice.

In tropical developing regions, typhoid fever and malaria often co-occur, posing serious health risks. The two illnesses have similar symptoms, which makes diagnosis and treatment more difficult. Through a thorough analysis of existing literature on typhoid fever, malaria, and co-infection, including research articles, case studies, and review papers, this review seeks to understand the dynamic interactions between typhoid fever and malaria co-infection. The review highlights important problems with co-infection between typhoid and malaria, such as higher morbidity and death, diagnostics-related challenges, and antibiotic resistance. Overlapping symptoms and limitations in current diagnostic tests impede accuracy. Treatment plans are made more difficult by the advent of typhoid strains that are resistant to drugs. The analysis concludes by highlighting the necessity of developing more sensitive and specific diagnostic methods in order to accurately diagnose co-infections. Going forward, the review emphasizes the need for more investigation into the immunological connections between malaria and typhoid illnesses. Essentially, this paper offers a thorough summary of the difficulties and possibilities related to co-infection between typhoid and malaria. It provides a framework for upcoming studies and initiatives that seek to improve public health and patient outcomes in the face of these intricately linked health problems.

Presently, Jordan confronts a double substantial challenge of enhancing energy security and mitigating greenhouse gas emissions. One of the most encouraging avenues to attain the objectives of sustainable development, energy security, and environmental conservation is to enhance the integration of renewable energy into the generation of electricity. In pursuit of this goal, the Jordanian government intends to expand investments in the green energy sector, with solar and wind energy poised to play a key role in satisfying energy demands and cultivating an environmental sustainability. This paper aims to examine the distinctive dynamics, challenges, obstacles, and potential solutions corresponding to the establishment of community solar and wind farms in Jordan suburban areas. It aims to highlight the opportunities and barriers influencing the track of sustainable energy adoption in the country. Through a comprehensive analysis of the Jordanian context, the goal is to extract insights that can guide policies and practices. Additionally, the findings may serve as a valuable benchmark for other regions confronting similar challenges on their pursuit for a sustainable energy future.

This paper explores the utilization of ensemble models and learning analytics techniques to predict student academic performance. With the advent of educational big data, institutions are increasingly leveraging advanced analytics to gain insights into student learning patterns and optimize educational outcomes. Ensemble models, which combine the predictive power of multiple algorithms, offer a robust approach to enhance prediction accuracy. The performance of the ensemble models was analyzed and compared using the Open University Learning Analytics Dataset, which consists of sources such as demographic information, historical performance data, and engagement metrics for 23,344 students. The evaluation of various ensemble models across different classification scenarios revealed that the proposed stacking model consistently emerges as the best-performing model, excelling in both multi-class and binary classification tasks.

This paper investigates the effect of Fe contamination on the microstructure and mechanical properties of Al-7Si-0.7Mg-Fe2.5 alloy processed by Laser Powder Bed Fusion (LPBF) and heat treated in two different conditions: (1) Solution Heat Treatment (SHT) at 520 °C, followed by artificial ageing at 160 °C (T6), and (2) Direct Artificial Ageing of the as-printed material at 160 °C (DAA). Microstructural characterization was carried out by Optical Microscopy (OM), X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Transmission Electron Microscope (TEM). Mechanical characterization was carried out by tensile tests at room temperature. The formation of fine AlSiFe phases such as α-AlFeSi, β-AlFeSi, and π-Al8Si6Mg3Fe had no deleterious effect on the mechanical properties compared to previous studies for AlSIMg alloys without Fe. However, compared to the as-printed condition, the T6 heat treatment decreased the ultimate tensile strain significantly, while the elongation to the fracture presented a slight improvement.

Abstract: Hyperuricemia is commonly diagnosed in subjects with abnormal purine metabolism. Prolonged hyperuricemia often associated with gout, which is a vital risk factor for joint dysfunction. The current study was designed to determine the efficacy of vitamin C supplements for treatment of high serum uric acid (UA) among hyperuricemic and gouty patients, and finding-out the effect of supplementation on serum creatinine (Cr) level and glomerular filtration rate (GFR). This intervention study was started in April, 2013, till two months. A convenient sample of 30 adults aged between 24-75 years of both genders was assigned into two study groups: hyperuricemic (n=15) and gouty (n=15) groups. Each participant supplemented with 500 mg/day vitamin C chewable tablets for 2 months. Serum UA, Cr, and GFR were measured before and after treatment. At the end of this study, Cr and GFR enhanced insignificantly in both groups. UA increased insignificantly in gouty group after 2 months by about 0.31 mg/dl. On the other hand, hyperuricemic group showed significant (P ≤0.05) decrease in UA (-0.78 mg/dl) after 2 months duration. In conclusion, supplementation with 500 mg/day vitamin C for 2 months significantly attenuated serum UA for hyperuricemic patients and insignificantly affected serum UA in gouty patients. The uselessness of vitamin C supplements on gouty patients could be associated to a number of possible reasons.

The article presents a model for optimizing biomass supply chains using the linear programming framework integrated with a Geographic Information System. Based on the distance from a given type of biomass resource, its calorific value, price, and transportation costs, the model identifies the optimal source of biomass, allowing it to cover the demand for the required total energy value with the lowest possible costs. The case study includes the Połaniec power plant in southeastern Poland and potential sources of forest biomass and agricultural straw within 100 km of the plant. Unit costs of biomass varied depending on biomass availability and energy demands. For energy demand on the level of 1 PJ yearly, the lowest unit costs of biomass (4.08 €/MJ) were when all kinds of biomass were available, and the highest (5.47 €/MJ) was when only stacked wood was available. As energy demand increased, unit costs increased, and the ability to meet this demand with just one type of biomass decreased. The energy biomass sector can utilize the model to benefit both biomass producers and their final buyers.

Gestational trophoblastic diseases (GTDs) encompass a spectrum of conditions characterized by abnormal trophoblastic cell growth, ranging from benign molar pregnancies to malignant trophoblastic neoplasms. This systematic review explores the molecular underpinnings of GTDs, focusing on genetic and epigenetic factors that influence disease progression and clinical outcomes. Based on 65 studies identified through systematic search and selection criteria, key findings include dysregulations in tumor suppressor genes such as p53, aberrant apoptotic pathways involving BCL-2, and altered expression of growth factor receptors and microRNAs. These molecular alterations not only differentiate molar pregnancies from normal placental development but also contribute to their clinical behavior, from benign moles to potentially malignant forms. The review synthesizes insights from immunohistochemical studies and molecular analyses to provide a comprehensive understanding of GTD pathogenesis and implications for personalized care strategies.

The classification of kidney tumors has undergone a remarkable evolution since the early 19th century, reflecting advances in medical science and technology. This historical overview traces the development of renal tumor classification, beginning with early clinical observations and macroscopic descriptions to the integration of molecular diagnostics in contemporary classifications. The establishment of international organizations like the World Health Organization (WHO) facilitated collaboration and standardization in tumor classification, leading to refined classifications and standardized nomenclature. Advancements in histological and molecular studies, particularly genetic analyses, revolutionized the understanding of renal cell carcinomas, enabling precise categorization based on molecular characteristics. The journey from rudimentary classifications to sophisticated systems based on detailed histological, immunohistochemical, and molecular criteria underscores the continuous evolution of kidney tumor classification. This article provides a comprehensive overview of this evolution, highlighting the contributions of scholars and the impact of technological advancements on our understanding and management of kidney tumors.

Enzymatic degradation of organic pollutants is a new and promising remediation approach. Peroxidases are one of the most commonly used classes of enzymes to degrade organic pollutants. However, it is generally assumed that all peroxidases behave similarly and produce similar degradation products. In this study, we conducted detailed studies of the degradation of a model aromatic pollutant, Sulforhodamine B dye (SRB dye), using two peroxidases—soybean peroxidase (SBP) and chloroperoxidase (CPO). Our results show that these two related enzymes had different optimum conditions (pH, temperature, H₂O₂ concentration...etc.) for efficiently degrading SRB dye. High-performance liquid chromatography and LC-mass spectrometry analyses confirmed that both SBP and CPO transformed the SRB dye into low molecular weight intermediates. While most of the intermediates produced by the two enzymes were the same, the CPO treatment produced at least one different intermediate. Furthermore, toxicological evaluation using lettuce (Lactuca sativa) seeds demonstrated that the SBP-based treatment was able to eliminate the phytotoxicity of SRB dye, but the CPO-based treatment did not. Our results show, for the first time, that while both of these related enzymes can be used to efficiently degrade organic pollutants, they have different optimum reaction conditions and may not be equally efficient in detoxification of organic pollutants.

Omega-3 polyunsaturated fatty acids (ɷ-3 PUFAs) offer diverse health benefits, such as supporting cardiovascular health, improving cognitive function, promoting joint and musculoskeletal health, and contributing to healthy aging. Despite their advantages, challenges like oxidation susceptibility, low bioavailability, and potential adverse effects at high doses persist. Nanoparticle encapsulation emerges as a promising avenue to address these limitations while preserving stability, enhanced bioavailability, and controlled release. This comprehensive review explores the therapeutic roles of omega-3 fatty acids, critically appraising their shortcomings and delving into modern encapsulation strategies. Furthermore, it explores the potential advantages of Metal-organic framework nanoparticles (MOF NPs) compared to other commonly utilized nanoparticles in improving the therapeutic effectiveness of omega-3 fatty acids within drug delivery systems (DDS). Additionally, it outlines future research directions to fully exploit the therapeutic benefits of these encapsulated omega-3 formulations for cardiovascular disease treatment.

Diesel is consistently a very popular fuel for internal combustion engines. Its consumption in the European Union has been rising over recent years, as has the number of engines increasingly sensitive to fuel contamination. One of the most important parameters affecting diesel quality is water content. Although its exceedances of the standard’s permissible amount are not common, they carry the risk of serious damage to expensive, modern fuel injection systems. Current methods of measuring water content require both specialised personnel and equipment, as well as transporting the sample to a suitable laboratory. The research presented in this paper was aimed at verifying whether it would be possible to test the moisture content of diesel using impedance spectroscopy. Once refined, such measurement method could be used in situ. Analysing the properties of diesel is challenging, mainly because many types of the fuel are sold, the chemical composition of which is always a well-guarded manufacturer’s secret. The experimental results obtained on many types of commercially available diesel show that it is possible to use impedance spectroscopy to estimate the water content of different types of diesel fuel. The measurement accuracy achieved makes it possible to detect approaching or exceeding the permissible water content.

The literature study delves into novel therapeutic strategies in transplantation medicine, highlighting unique approaches that could revolutionize current practices. It emphasizes novel patterns that have the potential to transform the current landscape. Commencing with a thorough examination of the historical environment, it traces crucial advances and changes in transplantation. The focus is on traditional techniques, emphasizing their limitations and challenges. An extensive examination of contemporary transplantation therapies offers valuable insights into the most recent progress in organ, cellular, and tissue transplantation. This analysis examines the immunological obstacles and outlines the current advancements and constraints. The exploration further navigates into novel models and concepts such as immunomodulation, developments in organ preservation techniques, gene editing, biomaterials, scaffold-based solutions, and the integration of precision medicine, artificial intelligence, and machine learning applications. Each section analyzes the potential for change and current progress in various areas, backed by relevant scientific sources up to 2023. The subsequent sections delve into innovative cellular therapies, biotechnological progress, current clinical trials, and case studies demonstrating effective applications. This examination delves into the ethical and regulatory considerations of innovative therapeutic procedures, emphasizing ethical implications, regulatory frameworks, and the importance of balancing innovation with patient welfare. The literature review concludes by offering a forward-looking perspective, emphasizing potential progress, anticipated challenges, and advocating for collaboration and interdisciplinary approaches to overcome limitations in the field of transplantation medicine.

For better understanding the corrosion and corrosion products behavior in the primary circuit of lead-bismuth eutectic (LBE) coolant reactor, the concentration distribution of soluble impurities and the transport of solid particles are investigated through finite-element method. An axisymmetric model of the primary circuit of LBE reactor was constructed to accelerate the calculation the thermal hydraulic filed of circuit. The saturation concentration of solute Fe, Cr and Ni in LBE coolant are identified through the equilibrium of their oxides and PbO. And the very different saturation concentrations of Fe/Cr/Ni in LBE will lead to significant element selective corrosion. The migration of solid oxides particles in the primary circuit is also investigated by the Euler-Lagrange tracing model. The simulation shows that driving force for the movement of particles >100 μm is buoyancy, which lets particles float on a free surface, while particles <10 μm tend to suspend in coolant. However, the behavior of particles also depends on the formation position, the particles formed above the core have the high possibility of re-entering in the core.

When asked to estimate the carbon footprint of a bundle of relatively low carbon footprint items and relatively high carbon footprint items, people typically report a lower value compared to estimating the high carbon footprint items alone. This finding is called the negative footprint illusion and suggests people report the average rather than sum of the combined items’ carbon footprint. In a recent paper by Gorissen et al. (2024), the authors claimed that people are immune to this illusion if the question is framed differently. Specifically, they found that estimates of the environmental friendliness of a set comprising a burger (high carbon footprint) and an organic apple (low carbon footprint) was higher than for a set comprising the burger alone, whereas no difference was found between the two sets when participants were asked to estimate how environmentally damaging they were. Using larger item categories wherein the degree of the items’ environmental impact is clearly communicated, here we show it does not matter whether participants are required to estimate how friendly or damaging the items are. The roles of attribute substitution, dependent variables, and independent variables (stimulus characteristics) in modulating the negative footprint illusion is discussed.

Elbow dislocation and instability present significant clinical challenges, necessitating a thorough understanding of the underlying bio-mechanical mechanisms. In this study, a quasi-static three-dimensional finite element model of the human elbow joint is developed to investigate stress distribution and stages of dislocation in the human elbow under various loading conditions. The model simulates the elbow joint in different degrees of flexion (30°, 45°, 60°, and 90°) and forearm positions (pronation and supination), providing detailed insights into the progression of dislocation. Significant findings include the identification of high stress concentrations on the humerus at 90° flexion and on the radial and coronoid processes at 30°, 45°, and 60° flexion. Three reproducible stages of dislocation were observed, particularly in flexed positions with forearm pronation or supination. These stages align with experimental observations and highlight the initial occurrence of bony failures, such as radial head and ulnar coronoid fractures, preceding soft tissue tears. Clinically, the study underscores that early-stage low-impact posterior elbow dislocations retain enough stability to be managed with closed reduction and early mobilization. However, as dislocations progress, significant damage to the medial and lateral collateral ligaments is expected, necessitating more invasive treatments. This research provides valuable bio-mechanical insights into elbow dislocation, aiding in the development of improved treatment strategies and enhancing patient outcomes through precise and timely clinical interventions. The validated FEM serves as a powerful tool for pre-surgical planning offering a comprehensive understanding of elbow joint mechanics.

Synovial sarcomas are rare soft tissue tumors that infrequently occur in the ethmoid sinus, posing diagnostic challenges. Herein, we report a case of a 38-year-old male with a 7-month history of recurrent throbbing headaches, left eye pain, and facial nerve palsy, evolving into multiple stroke episodes. Radiological studies showed extension to the cavernous sinus, raising an initial suspicion of vasculitis. Histological findings of an endoscopic biopsy, however, confirmed a monophasic synovial sarcoma. Consequently, the patient was referred to a specialized center for comprehensive management. This case underscores the rarity of ethmoid sinus synovial sarcomas, their diverse clinical presentations, and the necessity of a multidisciplinary approach for accurate diagnosis and tailored therapeutic strategies.

One of the important air pollutants is ammonia, which is mainly emitted from the agriculture sector. This sector is responsible for over 81% of global ammonia emissions. The main threat related to ammonia emissions is water eutrophication and soil acidification. The aim of the research was a preliminary assessment of the implementation status of methods for reducing ammonia emissions on farms and to learn the views and awareness of agricultural producers on reducing emissions of pollutants into the air. The research was conducted using a survey questionnaire that was made available to farmers in various ways. Based on the results of pilot surveys, it can be concluded that farmers have general knowledge of environmental protection and generally agree that people have an impact on the state of the environment. Low-emission practices to reduce ammonia emissions from agricultural sources are not widely used. The best situation is regarding reduction practices in the storage of natural fertilizers and the use of low-emission fertilizer application techniques. Some reduction activities are not obligatory, therefore it is difficult to determine the scope of application of these practices. Therefore, such periodic research will allow monitoring the activity of agricultural producers in implementing reduction methods.

Background Eating disorders are complex illnesses with serious long-term consequences. They are linked to negative outcomes such as miscarriage, low birth weight, and other obstetric and postpartum difficulties. Our study in Muscat, Oman, examines the eating habits of pregnant women who consult primary care physicians. We aim to understand how eating disorders affect pregnant women and inform more effective interventions. Method We used the Eating Disorder Examination Questionnaire to assess the potential for the presence of eating disorders. Chi-Square and Fisher's Exact tests were used to analyze relationships between improper eating behavior and independent variables. Results The study showed that 1.6% of participants had a potential diagnosis of an eating disorder, with the most common inappropriate behavior being binge-eating at a prevalence of 18.8%. A pre- gestational low Body Mass Index (BMI) was associated with a higher prevalence of binge eating during pregnancy. Additionally, we found that pregnant women who were working were more prone to self-induced vomiting. High BMI before pregnancy was significantly associated with various inappropriate eating behaviors such as restraint behavior (p = 0.000), shape concern (p = 0.000), weight concern (p = 0.040), eating (p = 0.045), laxative use (p = 0.020), and excessive exercise (p = 0.043). Conclusion The study reveals a high prevalence of eating disorders in pregnancy. Less educated women exhibit higher laxative use, while working women show more instances of binge eating and self-induced vomiting. These findings emphasize the critical need to prioritize targeted interventions and support for vulnerable pregnant women.

Keywords: Barriers; Facilitators; Sepsis; Sepsis Six Guidelines; Nurses.

The oxidative stress is one of the main cause for cardiovascular diseases (like Hypertension) also one of the results of these diseases. This study involved 56 subjects matched ages and sex divided into two groups; 28 hypertensive subject and 28 healthy subject as control group. The following analysis was done: 4-Hydroxy-2-nonenal(4HNE) and albumin. The results show that there is a significant increase in (4HNE) between patients group and control group. The increase in 4HNE which is a product of lipid peroxidation is attributed to destruction in body cell caused by due to the increase in stress events. It has been concluded that is important nappy on ideal weight, because obesity considered main factors for heart disease and hardening of the arteries. The aim of this study was to investigate the relationship between of some oxidative stress markers and cardiovascular diseases.

Diabetes mellitus (DM) has been defined as a group of metabolic diseases characterized by hyperglycemia resulting from defects in insulin secretion, insulin action, or both. This study includes (84) subjects, their age ranged from (40 to 54) years. (20) subjects were healthy chosen as control group and (64) patients with type 2 diabetes mellitus were divided into three groups according to their type of anti diabetic therapy: (23) newly diagnosed group without therapy (Group1), (20) with metformin therapy (Group2) and (21) with metformin plus glibenclamide therapies (Group3). In the study lipid profile level were quantitatively determine by enzymatic methods, in addition to that fasting plasma glucose (FPG), Glycated hemoglobin (HbA1c%) and body mass index (BMI) were identified in the patients. There is significant increase in the level of lipid profile in patients group. Metformin alone produce a non-significant favorable effect on all lipids profile parameters while metformin plus glibenclamide showed a significant reduction in TC and LDL-C.