This paper analyzes and compares models for predicting average magnet losses in interior permanent-magnet motors with fractional-slot concentrated windings due to harmonics in the armature reaction (assuming sinusoidal phase currents). Particularly, loss models adopting different formulations and solutions to the Helmholtz equation to solve for the eddy currents are compared to a simpler model relying on an assumed eddy-current distribution. Boundaries in terms of magnet dimensions and angular frequency are identified (numerically and using an identified approximate analytical expression) to aid the machine designer whether the more simple loss model is applicable or not. The assumption of a uniform flux-density variation (used in the loss models) is also investigated for the case of V-shaped and straight interior permanent magnets. Finally, predicted volumetric loss densities are exemplified for combinations of slot and pole numbers common in automotive applications.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

Natural gas hydrate, also known as combustible ice and mainly composed of methane, it is identified as the potential clean energy in the 21th century. Due to its large reserves, gas hydrate can ease problems caused by energy resource shortage and has gained attention around the world. In this paper, we focus on the exploration and development of gas hydrate as well as discussing its status and future development trend in China and abroad, then we analyze its opportunities and challenges in China from four aspects: resource, technology, economy and police with five forces model and PEST method. The results show, China has abundance gas hydrate resource; however the backward technologies and inadequate investment has seriously hindered the future development of gas hydrate, so China should establish relevant cooperation framework and intuitional arrangement to attract more investment as well as breaking through technical difficulties to make gas hydrate commercialization as soon as possible.

Reasonable allocation of production plans and saving the overall electricity cost are crucial for large manufacturing conglomerates, which is an effective way for conglomerates to realize open-source and cost-saving. This paper develops an optimization model of off-site industrial production scheduling for enterprises in response to the problems of high electricity costs due to the irrational allocation of production schedules on the demand side of China's electric power and the difficulty of promoting industrial and commercial distributed photovoltaic (PV) projects in China. The model makes full use of the conditions of different PV resources and different electricity prices in different places to optimize the scheduling of industrial production in different places. The model is embedded with two sub-models of the electricity price prediction model and distributed photovoltaic kWh cost model to complete the model parameters, in which the electricity price prediction model utilizes the LSTM neural network. The integrated model is then solved by the particle swarm algorithm. To verify the effectiveness of the model in solving the problem of off-site production scheduling on the demand side of electricity, the research team researched two off-site pharmaceutical factories belonging to the same large pharmaceutical company. Finally, the research data were substituted into the model for solving, and it was concluded that the optimization model could significantly reduce the cost of electricity consumption of the enterprise by about 7.9 %.

Accurate forecasting of icing thickness has a great significance for ensuring the security and stability of power grid. In order to improve the forecasting accuracy, this paper proposes an icing forecasting system based on fireworks algorithm and weighted least square support vector machine (W-LSSVM). The method of fireworks algorithm is employed to select the proper input features with the purpose of eliminating the redundant influence. In addition, the aim of W-LSSVM model is to train and test the historical data-set with the selected features. The capability of this proposed icing forecasting model and framework is tested through the simulation experiments using real-world icing data from monitoring center of key laboratory of anti-ice disaster, Hunan, South China. The results show that the proposed W-LSSVM-FA method has a higher prediction accuracy and it may be a promising alternative for icing thickness forecasting.

With the global objectives of achieving a ‘carbon peak’ and ‘carbon neutrality’, along with the implementation of carbon reduction policies, China’s industrial structure has undergone significant adjustments, resulting in constraints on high-energy consumption and high-emission industries while promoting the rapid growth of green industries. Consequently, these changes have led to an increasingly complex power system structure and presented new challenges for electricity demand forecasting. To address this issue, this study proposes a 24-step multivariate time series short-term load forecasting algorithm model based on KNN data imputation and BiTCN bidirectional temporal convolutional networks combined with BiGRU bidirectional gated recurrent units and attention mechanism. The Kepler adaptive optimization algorithm (KOA) is employed for hyperparameter optimization to effectively enhance prediction accuracy. Furthermore, using real load data from a wind farm in Xinjiang as an example, this paper predicts the electricity load from January 1st to December 30th in 2019. Experimental results demonstrate that our comprehensive short-term load forecasting model exhibits lower prediction errors and superior performance compared to traditional methods, thus holding great value for practical applications.

Open source software such as OpenDSS has given a lot of help to distribution network researchers and educators. With high penetration of distributed renewable energy resources into distribution network, tradition distribution steady state analysis software such as OpenDSS is faced with difficulty in handling distributed generators. Three-phase distributed generators are often modeled in sequence frame while unbalanced distribution network are usually modeled in phase frame. So a load flow in sequence-phase coupled frame is proposed to handle models described in both frames. Voltage controlled DGs which are difficult to cope with in OpenDSS are handled in proposed program. The steady state analysis platform is programmed with open source Modelica language and the main aim of this paper is to introduce an open source platform for active distribution network steady analysis include load flow and short circuit analysis which can be easily adopted and improved by other educators and researchers.

Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

In order to solve the problem of large eddy current loss and high temperature rise caused by large amount of permanent magnet, a new type of combined magnetic pole permanent magnet motor is proposed in this paper. The sinusoidal distribution subdomain model of non-uniform air gap rotor is established by using Laplace equation, and the analytical expression of eddy current loss of rotor in uniform air-gap and non-uniform air-gap is derived. The effect of rotor eccentricity on eddy current loss is obtained. According to the characteristics of distributed winding of non-uniform air gap combined pole permanent magnet motor, equivalent treatment is performed to obtain the equivalent thermal conductivity, so as to establish equivalent thermal network model of motor, calculate the temperature value of each component of the motor, and verify the correctness of the thermal network model through the method of magnetothermal bidirectional coupling. Finally, an experimental platform is set up to carry out temperature rise experiments on the two prototypes respectively. Experimental results show that the non-uniform air-gap rotor structure can effectively reduce the rotor eddy current loss and motor temperature rise, and also verify the accuracy of the analytical model calculation results.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

More and more works are using machine learning techniques while adopting supervisory control and data acquisition (SCADA) system for wind turbine anomaly or failure detection. While parameter selection is important for modelling a wind turbine’s health condition, only a few papers have been published focusing on this issue and in those papers interconnections among sub-components in a wind turbine are used to address this problem. However, merely the interconnections for decision making sometimes is too general to provide a parameter list considering the differences of each SCADA dataset. In this paper, a method is proposed to provide more detailed suggestions on parameter selection based on mutual information. Moreover, after proving that Copula, a multivariate probability distribution for which the marginal probability distribution of each variable is uniform is capable of simplifying the estimation of mutual information, an empirical copula based mutual information estimation method (ECMI) is introduced for an application. After that, a real SCADA dataset is adopted to test the method, and the results show the effectiveness of the ECMI in providing parameter selection suggestions when physical knowledge is not accurate enough.

For offshore wind power generation, accessibility is one of the main factors that has great impact on operation and maintenance due to constraints on weather conditions for marine transportation. This paper presents a framework to explore the accessibility of an offshore site. At first, several maintenance types are defined and taken into account. Next, a data visualization procedure is introduced to provide an insight into the distribution of access periods over time. Then, a rigorous mathematical method based on finite state Markov chain is proposed to assess the accessibility of an offshore site from the maintenance perspective. A five-year weather data of a marine site is used to demonstrate the applicability and the outcomes of the proposed method. The main findings show that the proposed framework is effective in investigating the accessibility for different time scales and is able to catch the patterns of the distribution of the access periods. Moreover, based on the developed Markov chain, the average waiting time for a certain access period can be estimated. With more information on the maintenance of an offshore wind farm, the expected production loss due to time delay can be calculated.

The lack of defect image data is one of the main factors affecting the accuracy of supervised deep learning-based defect detection models. In response to the insufficient training data of defect images with complex backgrounds such as rust and surface oil leakage in substation equipment, leading to poor performance of the detection model, this paper proposed a novel adversarial deep learning model for substation defect generation: ADD-GAN. In comparison to existing generative adversarial networks, this model generates defect images based on effectively segmented local areas of substation equipment images, avoiding image distortion caused by global style changes. Additionally, the model utilizes a joint discriminator for overall image and defect image to address the issue of low attention to local defect areas, thereby improving the loss of image features. This enhances the overall quality of generated images as well as locally generated defect images, ultimately improving image realism. Experimental results demonstrate that the YOLOV7 object detection model trained on the dataset generated using the ADD-GAN method achieves an mAP of 81.5% on the test dataset, representing an improvement of 9.6% over the original dataset, 5.7% over traditional augmentation methods, and 7% over typical adversarial deep learning methods. This confirms that the ADD-GAN method can generate a high-fidelity dataset of substation equipment defects.

In the modern power grid, characterized by the increased penetration of power electronics and extensive utilization of renewable energy, inverters-based power plants play a pivotal role as the principal interface of renewable energy sources (RESs) and the grid. Considering the stability characteristics of grid-following (GFL) inverters when the grid is relatively weak, the application of grid-forming (GFM) controls becomes imperative to enhance the stability of the entire power plant. Thus, there is an urgent need for suitable and effective models to study the interaction and stability of the paralleled inverters employing GFL and GFM controls. Thus, the small-signal modeling with full-order state space model and eigenvalues analysis is presented in this paper. First, the small-signal state-space model of the individual GFL and GFM inverters is obtained considering the control loop, interaction, reference frame, transmissions, and time delays. Then, the models of the individual inverter are extended to the hybrid inverters to study the effects of the GFM inverters on the small- signal stability of the entire system. And, the impacts of the inertia and damping are analyzed by the eigenvalues of the state-transition matrix. Case comprising three parallel GFL inverters and two GFL inverters with one GFM inverter, respectively, are studied to examine the effectiveness and accuracy of the model. Finally, the stability margin obtained from the eigenvalue analysis of the entire system is verified by time-domain simulations.

Traditional concrete pavements have poor water permeability, while the strength of pervious concrete pavements is low. To solve these problems, this study designed Innovative recycled aggregate pervious concrete (I-RAPC) with controllable water permeability and high strength by using response surface methodology, and investigated the effects of different pore parameters (number, diameter, material, distribution form, etc.) on the performance of I-RAPC. And the strength discount factor method was proposed to construct the theoretical calculation model of compressive strength and pipe pore parameters, and the calculation model of water permeability coefficient was established at the same time. The results show that the fewer the number of holes and the smaller the pipe diameter of I-RAPC, the higher its compressive strength and the smaller the water permeability coefficient. The theoretical model of compressive strength can accurately evaluate the discounting effect of the pore parameters on the compressive strength of I-RAPC, and the maximum relative error is only 7.52%, and the maximum relative error of the calculation model of water permeability coefficient is only 4.42%. I-RAPC has the advantages of high strength and permeability with controllable performance, which overcomes the problems of random distribution of pore space, uncertainty of water permeability, and strength of ordinary pervious concrete.

Remote Photoplethysmography (rPPG) has emerged as a non-intrusive and promising physiological sensing capability in HCI research, gradually extending its applications in health-monitoring and clinical care contexts. With advanced machine learning models, recent datasets collected in real-world conditions have gradually enhanced the performance of rPPG methods in recovering heart-rate and heart-rate variability metrics. However, the signal quality of reference ground-truth PPG data in existing datasets is by and large neglected, while poor quality references negatively influence models. Here, this work introduces a new imaging blood volume pulse (iBVP) dataset of synchronized RGB and thermal infrared videos with PPG ground-truth signals from the ear and its high resolution signal quality labels, for the first time. Participants perform rhythmic breathing, head-movement, and stress-inducing tasks, which help reflect real-world variations in psycho-physiological states. This work conducts dense (per sample) signal quality assessment to discard noisy segments of ground-truth and corresponding video frames. We further present a novel end-to-end machine learning framework, iBVPNet that features an efficient and effective spatio-temporal feature aggregation for reliable estimation of BVP signals. Finally, this work examines the feasibility of extracting BVP signals from thermal video frames, which is underexplored. The iBVP dataset and source codes are publicly available for research use.

The development of accurate dynamic battery pack models for electric vehicles (EVs) is critical for the ongoing electrification of the global automotive vehicle fleet, since these serve as a key element in the energy performance of an EV powertrain system. The Equivalent Circuit Model (ECM) technique at the cell level is commonly employed for this purpose, combining accuracy and efficiency in the representation of battery operation within the broader powertrain system. In this study, a second-order ECM model of a battery cell is being developed using Modelica, an equation-based modeling language. Parameter lookup tables at multiple levels of state of charge (SoC), extracted from Li-ion battery cells with 4 different commonly used cathode materials, have been utilized. This approach allows for a representation of the battery systems that are used in a wide range of commercial EV applications. To verify the model, an integrated EV model is developed and simulation results of the FTP75 driving cycle have been compared against an equivalent application in MATLAB Simulink. The findings demonstrate a close match between the results obtained from both software across different system points. Specifically, the maximum deviation of SoC is limited to 0.08% and the maximum value of relative voltage deviation is 1.4%. The verified model enables the exploration of multiple possible architecture configurations of EV powertrains with Modelica.

With the development of higher voltage power grid, the high and low voltage parallel loops are emerging, which lead to energy losses, even threaten the security and stability of power system. The multi-infeed HVDC configurations widely appearing in AC/DC interconnected power system make this situation even worse. Aimed at energy saving and system security, a decision optimization method for power grid operating condition with high and low voltage parallel loops is proposed in this paper. Firstly, considering hub substation distribution and power grid structure, parallel loop opening schemes are generated with GN algorithm. Then, candidate opening schemes are preliminarily selected from all these generated schemes based on a filtering index. Finally, with the influence on power system security, stability and operation economy in consideration, an evaluation model for candidate opening schemes is founded based on analytic hierarchy process (AHP). And a fuzzy evaluation algorithm is used to find the optimal scheme. Simulation results of New England 39-bus system and an actual power system validate the effectiveness and superiority of this proposed method.

When a grid-forming (GFM) inverter is connected to a low or medium voltage weak power grid, the line impedance with resistive-inductive characteristics will cause power coupling. Typical GFM decoupling control strategies are designed under nominal line impedance parameters. However, there are deviations between the nominal line impedance and actual parameters, resulting in poor decoupling effects. Aiming at this problem, this paper proposes a power decoupling strategy based on a reduced-order extended state observer (ESO). Firstly, the power dynamic model of GFM is established based on the dynamic phasor method. Then, the model deviation and power coupling due to line impedance parameter perturbation are estimated as internal disturbances of the system, and the disturbances are compensated on the basis of typical power control strategy and virtual impedance decoupling. Good decoupling performance is obtained under different impedance parameters, improving the control strategy's robustness. Finally, the effectiveness of the proposed method is verified by the results of RT Box hardware-in-the-loop experiments.

The widespread adoption of IoT networks has revolutionized modern life thanks to their diverse range of applications. With their increased usage, the need to transfer data securely has never been more vital. Often IoT devices are battery-driven and possess limited processing and storage capabilities. In response to those limitations, there has been a shift towards the implementation of resource-efficient and lighter protocols. This research aims to evaluate how lightweight key establishment through Object Security for Constrained RESTful Environments (OSCORE) and Ephemeral Diffie-Hellman Over COSE (EDHOC) can enhance cybersecurity in IoT networks where resources are limited. The study aims to explore different key management approaches and the effects of certificates on security, efficiency, and power consumption. The research methodology consists of the practical implementation of the protocols in a physical system where factors such as the impact of hardware acceleration on computational overhead and overall power consumption will be assessed. Furthermore, the study will verify the cost of resources and overall efficiency, evaluating them against real-world scenarios. The expected contributions of this study are insights into the tradeoffs between security, power consumption, and efficiency in resource-limited IoT environments.

To enhance the overall reliability of the power system, engineers have redirected their focus toward health monitoring and early detection of faults in transformers. Among these faults, transformer core defects demand particular attention. While fault simulation using software has traditionally been the preferred approach, these methods suffer from data inaccuracies in real-world conditions. Consequently, conducting actual experimental setups with induced faults is imperative to investigate core issues. This study uses Hilbert Transform (HT) as a signal processing technique to extract crucial data characteristics, thereby enhancing the performance of the classifier model. The research involves analyzing electric current signals from a single-phase 1kVA transformer. A comparative assessment of our proposed model was conducted using raw data and Fast Fourier Transform (FFT), evaluating accuracy, precision, recall, F1-score, and computational time. The results demonstrate a significant improvement in all metrics for the classifier models, particularly the k-nearest neighbor (KNN) algorithm, which exhibited values of 83.89%, 84.39%, 83.89%, 83.79%, and 0.0156 seconds, respectively. Future work aims to extend this analysis under different loading conditions.

This study builds on our previous Systematic Literature Review (SLR) that assessed the applications and performance of zk-SNARK, zk-STARK, and Bulletproof Non-Interactive Zero-Knowledge Proof (NIZKP) protocols. To address identified research gaps, we designed and implemented a benchmark comparing these three protocols using a dynamic MiMC hash application. We evaluated performance across four general-purpose programming libraries and two programming languages. Our results show that zk-SNARK produced the smallest proofs, while zk-STARK generated the largest. In terms of proof generation and verification times, zk-STARK was the fastest, and Bulletproof the slowest. Interestingly, zk-SNARK proofs verified marginally faster than zk-STARK, contrary to other findings. These insights enhance our understanding of the functionality, security, and performance of NIZKP protocols, providing valuable guidance for selecting the most suitable protocol for specific applications.

A novel drive current model covering the effects of source/drain voltage (VDS) and gate voltage (VGS) and incorporating drift and diffusion current on the surface channel at the nano-node level, especially beyond 28nm node is presented. The effect of the diffusion current added is more satisfactory to describe the behavior of the drive current in nano-node MOSFETs, fabricated with the atomic-layer-deposition (ALD) technology. This breakthrough in model establishment can expose the long and short channel devices together. Introducing the variables of VDS and VGS, the mixed current model more effectively and meaningfully demonstrates the drive current of MOSFETs under the operation of horizontal, vertical, or mixed electrical field. In comparison between the simulation and experimental consequences, the electrical performance is impressive. The error between both is less than 1%, better than the empirical adjustment to issue a set of drive current models.

Exposure to quasi-electrostatic field induced currents is a hazard of live-line transmission work. These steady-state induced currents are typically less than 1 mA, and their sensory effects range from imperceptible to painful depending on the person and conditions such as contact area and duration. Permanent injury from these currents is unlikely but they can distract workers, increasing the risk of injury from falls or other dangers. Identifying contact current severity and training workers can help reduce risk of accidents. Measuring induced currents along a climbing route is time consuming and simulation is challenging because of geometric complexity of the worker, transmission structure, conductor bundles, and electric fields in the climbing space. This research explores calculation of worker contact current using a recently developed adaptation of the charge simulation method. The method uses Fourier principles to improve computational efficiency when explicitly modeling all bundle subconductors. The research also examines reasonable simplifications for modeling lattice structures and human geometry. Calculated results compare well to measured currents for a worker climbing a 400 kV lattice structure. This indicates the method is a practical option for calculating the severity of steady-state contact currents. A simple calculation is suggested for estimating these currents.

Optimizing the NACA0015 airfoil which is widely applied in small-scale vertical axis wind turbine to make it has a better aerodynamic performance. In the optimization process, using CST parameterization method to perturb the airfoil geometry, the thickness and camber of the airfoil are selected as the constraint, and the value of the maximum tangential force coefficient is chosen as the objective function, the genetic algorithm based on non-dominated sorting (NSGA-II)is selected as an optimization method, calculates the aerodynamic performance of the airfoil by applying the approach of combining XFOIL program and Viterna-Corrigan post-stall mode ,and establishes the optimizing process by the optimization software modefrontier for NACA0015 airfoil’s muti-point optimization, validate the airfoil’s performance with CFD finally. The result illustrates that, by comparing with the NACA0015 airfoil, the optimized airfoil’s lift to drag ratio is improved over a wide range of attack angles, the stall performance is more gentle. The maximum lift coefficient, the maximum lift-drag ratio and the maximum tangential force coefficient are increased by 7.5%,9 and 8.87%, respectively. The optimized airfoil has a wide variable condition performance, more suitable for the operating conditions of a vertical axis wind turbine. Finally, predict the rotor efficiency with optimized airfoil and NACA0015 airfoil for different tip speed ratios and different solidities with multiple streamtube model, the result shows the rotor with optimized airfoil has a higher efficiency.

The object of study in the article is the auxiliary variable-frequency electric drive onboard of an AC electric locomotive, and more precisely, the structure and parameters of the control system of the active corrector of power factor (ACPF), which is part of the electric drive, as a unit that ensures electromagnetic compatibility of the electric drive with other equipment on board the electric locomotive and catenary and its energy efficiency. The topic of the article's research is the substantiation of the structure of the ACPF control system, the choice of types (transfer functions) of controllers and the calculation of their parameters. The research method chosen was the calculation of the transfer functions of the controllers of the cascaded loops control system, followed by computer simulation using the OrCAD software. The results of simulating a cascaded two loops control system of an ACPF with different types of controllers are presented and analytically compared. It is concluded that it is advisable to use a cascaded two loops control system, containing a voltage control loop and a current control loop. The best results show the simulation when using an aperiodic current controller (A-controller) and a proportional-integral voltage controller (PI-controller). The data obtained serve as the basis for further improvement of the operation of the ACPF by enhancing and optimizing the settings, structure and algorithms of the control system, which, with the selected hardware of power converter unit, will allow the ACPF to perform its functions with a high degree of reliability in an entire range of disturbing and control influences.

Energy storage systems play a crucial role in the overall performance of hybrid electric vehicles. Therefore, the state of the art in energy storage systems for hybrid electric vehicles has been discussed in this paper along with appropriate background information for facilitating future research in this domain. Specifically, we have compared the key parameters such as cost, power density, energy density, cycle life, and response time for various energy storage systems. For the energy storage systems employing ultra capacitors, we have presented the characteristics such as cell voltage, cycle life, power density and energy density. Furthermore, we have discussed and evaluated the interconnection topologies for the existing energy storage systems. We have also discussed the hybrid battery-flywheel energy storage system as well as the mathematical modeling of the battery-ultracapacitor energy storage system. Toward the end, we have discussed energy efficient powertrain for hybrid electric vehicles.

A new type of artificial block is proposed by modifying the traditional block. Based on the physical model experiment, the wave reflection and run-up characteristics of the new ecological blocks under regular waves were examined, and the influence of the height of the "planting trough" border on the hydrodynamic properties was analyzed. The results indicate that the wave reflection and run-up would decrease with a decrease in the breakwater slope. As wave height increases, wave run-up increases, and the reflection coefficient falls. Wave reflection and run-up increase with an increasing wave period. The relative depth of the water has a smaller impact on the wave reflection than the wave run-up. The reflection coefficient of the new ecological blocks is consistently lower than that of the conventional and continues to decrease as the border of the "planting trough" is raised. The raised borders prevent water loss in the trough, resulting in no significant improvement in the wave run-up performance of the new blocks. The reflection coefficient and the relative run-up R/H gradually increase with the average wave breaking parameter ξ increase. The crude permeability coefficients for the new blocks, New Heights 1 and New Heights 2, are 0.53, 0.53, and 0.54, respectively.

There are many uncertainties and risks in residential electricity consumption during the economic development. Knowledge of the relationship between residential electricity consumption and its key determinant—income—are important to the sustainable development of electric power industry. Using panel data from 30 provinces for the 1995-2012 period, this study investigates how residential electricity consumption changes as incomes increase in China. Previous studies typically used linear or quadratic double-logarithmic models imposing ex ante restrictions on the indistinct relationship between residential electricity consumption and income. Contrary to those models, we employed a reduced piecewise linear model that is self-adaptive and highly flexible and circumvents the problem of “prior restrictions.” Robust tests of different segment specifications and regression methods are performed to ensure the conservatism of the research. The results provide strong evidence that the income elasticity was approximately one, and it remained stable throughout the estimation period. The income threshold at which residential electricity consumption automatically remains stable or slows has not been reached. To ensure the sustainable development of the electric power industry, introducing higher energy efficiency standards for electrical appliances and improving income levels are vital. And government should emphasize electricity conservation in industrial sector rather than in residential sector.

The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

In order to improve contrast and restore color for underwater image captured by camera sensors without suffering from insufficient details and color cast, a fusion algorithm for image enhancement in different color spaces based on contrast limited adaptive histogram equalization (CLAHE) is proposed in this article. The original color image is first converted from RGB color space to two different special color spaces: YIQ and HSI. The color space conversion from RGB to YIQ is a linear transformation, while the RGB to HSI conversion is nonlinear. Then, the algorithm separately operates CLAHE in YIQ and HSI color spaces to obtain two different enhancement images. The luminance component (Y) in the YIQ color space and the intensity component (I) in the HSI color space are enhanced with CLAHE algorithm. The CLAHE has two key parameters: Block Size and Clip Limit, which mainly control the quality of CLAHE enhancement image. After that, the YIQ and HSI enhancement images are respectively converted backward to RGB color. When the three components of red, green, and blue are not coherent in the YIQ-RGB or HSI-RGB images, the three components will have to be harmonized with the CLAHE algorithm in RGB space. Finally, with 4 direction Sobel edge detector in the bounded general logarithm ratio operation, a self-adaptive weight selection nonlinear image enhancement is carried out to fuse YIQ-RGB and HSI-RGB images together to achieve the final fused image. The enhancement fusion algorithm has two key factors: average of Sobel edge detector and fusion coefficient, and these two factors determine the effects of enhancement fusion algorithm. A series of evaluate metrics such as mean, contrast, entropy, colorfulness metric (CM), mean square error (MSE) and peak signal to noise ratio (PSNR) are used to assess the proposed enhancement algorithm. The experiments results showed that the proposed algorithm provides more detail enhancement and higher values of colorfulness restoration as compared to other existing image enhancement algorithms. The proposed algorithm can suppress effectively noise interference, improve the image quality for underwater image availably.

Greek roots: "phos" (φῶς) - means "light" and "dynamis" (δύναμις) - means "force" or "power". Photodynamic therapy (PDT) is an innovative treatment method based on the ability of photosensitizers to produce reactive oxygen species after exposure to light of a specific wavelength range, either in the visible or near infrared range. This process results in damage to pathological cells, such as cancer cells, while minimizing the impact on healthy tissues. PDT is a promising direction in the treatment of many diseases, with particular emphasis on the fight against cancer and other diseases asso-ciated with excessive cell growth. The power of light contributed to the creation of phototherapy, whose history dates back to ancient times. It was then noticed that some substances exposed to the sun have a negative effect on the body, while others have a therapeutic effect. This work provides a detailed review of photodynamic therapy, from its origins to the present day. It is surprising how a seemingly simple beam of light can have such a powerful healing effect, which is used not only in dermatology, but also in oncology, surgery, microbiology, virology, and even dentistry. However, despite promising re-sults, photodynamic therapy still faces many challenges. The availability of this thera-py is limited due to the small number of centers offering this type of treatment and the high costs, which may be unaffordable for many patients. Moreover, photodynamic therapy requires further research and improvement.

The plastic deformation behavior of 3Y-TZP with weak electric current in oxygen-lean atmosphere was investigated. An electrochemical reduction reaction, induced by the electric current, can significantly promote the plastic deformation of 3Y-TZP at furnace temperature of 1200 °C and a strain rate of 6.67 × 10−4 s−1. Especially, a remarkable variation of the electrical property and grain growth were observed in 3Y-TZP during the deformation. The stress exponent ranging within 2~3 indicated that the deformation was dominated by grain boundary sliding. The applied electric current decreased the apparent activation energy Q of the deformation from 465 kJ mol-1 to 315 kJ mol-1, resulting in a transition of the diffusion mechanism from the lattice diffusion to the grain boundary diffusion. These phenomena were mainly attributed to the enhancement of the cation diffusion caused by the electrochemical reduction reaction, which induced by the electric current in oxygen-lean atmosphere.

Regeneration of lost tail is of great importance to lizards. Anolis carolinensis, a green lizard, is capable of regenerating its tail efficiently after autotomy. Hence, it is considered as a model organism in regeneration study. A. carolinensis shed its tail in order to distract the predator’s attention and thus makes a way to escape. Restoring of the amputated tail takes several days and the mechanism is currently clearly understood. Although save its life, tail regeneration is associated with the impairment of several vital functions in Anoles. In addition, various differences have been observed between original and regenerated tail in terms of mechanism and structure. To date, very little work has been conducted on tail autotomy and regeneration at molecular and genetic level. The genes responsible for regeneration in anoles are identified recently. These genes are evolutionarily conserved through all tetrapod vertebrates. They are, however, in a state of ‘switched-off’ in other vertebrates including humans. Consequently, a throughout study of these so called ‘switched-off’ genes may provide a way of restoring lost organs in human, and thus could revolutionize the modern medical science.

Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

The state-of-the-art smart city has been calling for an economic but efficient energy management over large-scale network, especially for the electric power system. It is a critical issue to monitor, analyze and control electric loads of all users in system. In this paper, we employ the popular computer vision techniques of AI to design a non-intrusive load monitoring method for smart electric energy management. First of all, we utilize both signal transforms (including wavelet transform and discrete Fourier transform) and Gramian Angular Field (GAF) methods to map one-dimensional current signals onto two-dimensional color feature images. Second, we propose to recognize all electric loads from color feature images using a deep neural network with multi-scale feature extraction and attention mechanism. Third, we design our method as a cloud-based, non-intrusive monitoring of all users, thereby saving energy cost during electric power system control. Experimental results on both public and our private datasets have demonstrated our method achieves superior performances than its peers, and thus supports efficient energy management over large-scale Internet of Things.

Small peptides (SPs), ranging from 5 to 100 amino acids, play integral roles in plants due to their diverse functions. Despite their low abundance and small molecular weight, SPs intricately regulate critical aspects of plant life, including cell division, growth, differentiation, flowering, fruiting, maturation, and stress responses. As vital mediators of intercellular signaling, SPs have garnered significant attention in plant biology research. This comprehensive review delves into SPs' structure, classification, and identification, providing a detailed understanding of their significance. Additionally, we summarize recent findings on the biological functions and signaling pathways of prominent SPs that regulate plant growth and development. The review also offers a forward-looking perspective on future research directions in peptide signaling pathways.

Immune checkpoint inhibitors (ICI) are a promising form of immunotherapy that has significantly changed the therapeutic landscape for many advanced cancers. They have shown unique clinical benefit against a broad range of tumour types and a strong overall impact on survival in studied patient populations. However, there are still many limitations holding back this immunotherapy from reaching its full potential as a possible curative option for advanced cancer patients. A great deal of research is being undertaken in the hope of driving advancements in this area, building a better understanding of the mechanisms behind immune checkpoint inhibition and ultimately developing more effective, safer, and wider-reaching agents. Taking into account the current literature on this topic, this review aims to explore in depth the basis of the use of ICIs in the treatment of advanced cancers, evaluate its efficacy and safety, consider its current limitations, and finally reflect on what the future holds for this very promising form of cancer immunotherapy.

This article proposes a particular strategy to proceed with a progressive electrification of public transport systems in cities. Starting from a bus operation model, the possible electrification of two routes is analysed, one urban and another extra-urban in the city of Pisa. An estimate is made of the energy uses associated with certain operating modes. The maximum level of consumption is estimated at approximately 280 kWh per day per bus for the urban route and excluding some special days, less than 215 kWh per day for the extra-urban route, for which a hybrid bus is proposed. Starting from an estimate of the daily consumption for the management of the two routes, the sizing of a photovoltaic system distributed on some modular shelters which serves to power the same routes is carried out. The resulting system has a power of the order of 190-200 kW. The modular solution is also outlined, and an installation is proposed. The analyzed case lends itself to being easily replicated.

The electric vehicle (EV) industry is experiencing rapid growth, accompanied by continuous advancements in charging infrastructure to satisfy the rising need for fast and reliable charging. Particularly, the focus has shifted towards EV fast charging (EVFC) and its impact on the power grid. This paper presents a comprehensive analysis and survey of scholarly literature and projects conducted in this field over the past decade. The findings highlight the rising demand for EVFC and the need to address its potential adverse effects on the power grid. However, there is a noticeable lack of clear research guidance regarding charging time. To tackle these challenges and pave the way for future solutions, extensive research on DC fast charging, ultra-fast charging, and the integration of vehicle-to-grid (V2G) systems is required. This review paper thoroughly investigates the development of fast charging technology for electric vehicles (EVs), including its advantages and comparative analyses from various perspectives. Furthermore, it delves into the advancements in DC fast charging infrastructure, emphasizing charging standards and control modes. The study also investigates different categories of battery chargers for both on-board and off-board charging. Additionally, it explores the classification of DC-DC converters in the context of DC fast charging stations, discusses control strategies for EV systems, identifies existing challenges, and outlines future trends in EV fast charging.

Natural polluted insulator surfaces are always coated with various kinds of soluble constituents, and those constituents affect flashover performance differentially. Currently this fact is not considered either in laboratory experiments or field pollution degree measurements, causing the existing insulation selection method to be deficient. In this paper a systematical research on insulator flashover voltage gradient correction involving types of soluble pollution constituents was presented. Taking typical type glass insulator as the sample, its flashover tests polluted by typical soluble chemicals NaCl, NaNO₃, KNO₃, NH₄NO₃, MgSO₄, Ca(NO₃)₂ and CaSO₄ were carried out. Then the flashover gradient correction was made combining the flashover performance of each soluble constituent, the ESDD contribution of the seven constituents, as well as the saturation performance of CaSO₄. The correction was well verified with the flashover test results of insulator polluted by three types of soluble mixture. Research results indicate that the flashover gradient correction method proposed by this paper performs well in reducing the calculating error. It is recommended to carry out component measurements and flashover gradient correction to better select outdoor insulation configuration.

The working environment of mining electric locomotives is wet and muddy coal mine 1 roadway. There may be idling or slipping between the wheels and rails of mining electric locomotives 2 due to low friction between the wheel and rail and insufficient utilization of creep rate. Therefore, it 3 is necessary to control the creep rate within a reasonable range. In this paper, the autonomous control 4 algorithm for mining electric locomotives based on improved ε-greedy is theoretically proven to be 5 convergent and effective firstly. Secondly, after analyzing the contact state between the wheel and rail 6 under wet and slippery road conditions, it was concluded that the value of creep rate is an important 7 factor affecting the autonomous driving of mining electric locomotives. Therefore, the autonomous 8 control method for mining electric locomotives based on creep control is proposed in this paper. 9 Finally, the effectiveness of the proposed method was verified through simulation. The problem of 10 wheel slipping and idling caused by insufficient friction of mining electric locomotives in coal mining 11 environments is effectively suppressed. Autonomous operation of vehicles with optimal driving 12 efficiency can be achieved through quantitative control and utilization of the creep rate between 13 wheels and rails

Ensuring precise electric locomotive stopping is pivotal for achieving intelligent and unmanned auxiliary transportation systems. Currently, human drivers' expertise plays a central role in the stopping process, posing challenges for automation and cargo location accuracy, particularly in coal mining. This paper focuses on achieving accurate electric locomotive stopping under diverse conditions by utilizing permanent magnet synchronous motor-driven locomotives. This technique introduces a novel stopping control method that combines a fuzzy Proportional-Integral-Derivative (F-PID) controller and a vector control model for permanent magnet synchronous motors (PMSM). After this, we design the F-PID using the PMSM technique based on the new fuzzy rules for each sub-system. In the end, extensive simulations and real-world experiments are conducted on an electric locomotive stopping test bed, which demonstrate the effectiveness of the proposed control method. From the simulation results, it confirming that the ability to achieve precise stopping under various working conditions.

This paper addresses the evolving landscape of electricity markets in Europe, with a focus on the integration of Renewable Energy Communities as introduced by the Renewable Energy Directive 2018/2001. Residents within a postal code area are highly incentivized to join a community, which enables them to exchange energy among themselves at lower procurement costs. Thereby, energy management systems optimize the operation of respective energy systems, with electrical load forecasting playing a key role. Given that prosumers may switch between communities on a daily basis, electricity demands within these groups will vary, leading to data that is non-stationary, discontinuous as well as non-identical and independently distributed. To encounter this issue, we propose a sophisticated forecasting model that applies federated learning, using informations from various distributed communities to learn domain-invariant features. To achieve this, we initially utilize synthetic electrical load time series at district level and aggregate them to profiles of Renewable Energy Communities with dynamic portfolios. Subsequently, we develop a forecasting model that accounts for the composition of residents of a Renewable Energy Community, adapt data pre-processing in accordance with the time series process, and detail a federated learning algorithm that incorporates weight averaging and data sharing. Following the training of various experimental setups, we ultimately evaluate their effectiveness. The findings suggest that our proposed framework is capable of effectively forecast non-stationary and discontinuous time series and that it can be applied to new, unseen data through the integration of knowledge from multiple sources.

Among earth’s microbial populations are the genes, functional capacities, generational memory and sentient cognition that enable microorganisms to adapt and thrive in the full range of ecological conditions found on planet earth. In prior sequential publications, we considered fundamental properties (e.g., use of and responses to sound, light, vibrations) and features of microorganisms that cause them to be critical co-partners of human and other holobionts as well as the potential benefits for humanity that can be gained by fully applying quantum-related and novel capacities of microbial life. In this narrative review we: 1) discuss key concepts concerning a microbially-enhanced and sustainable future, and 2) focus on electric- and magnetic- based features of microorganisms that make them pivotal for myriad benefits ranging from beyond pharma-based health and wellness to free- and/or renewable energy and restorative agriculture to improved human networking. While the benefits are many, the risks posed by hazardous electric or magnetic field exposures to both holobionts and microbial communities are significant. This review concludes that microbes and their remarkable capacities offer both humanity and the planet a much brighter future if we reverse the demonization of microbes and wanton microbiome degradation that has predominated much of the past century.

Addressing the pressing challenge of global warming, reducing greenhouse gas emissions in the transportation sector is a critical imperative. Battery and fuel-cell electric vehicles have emerged as promising solutions for curbing emissions in this sector. In this study, we conducted a comprehensive life cycle assessment (LCA) for typical passenger vehicles, heavy duty trucks and city buses using either proton-exchange membrane fuel cells or Li-ion batteries with different cell chemistries. To ensure accuracy, we supplemented existing studies with data from the literature, particularly for the recycling phase, as database limitations were encountered. Our results highlight that fuel cell and battery systems exhibit large emissions in the production phase. Recycling can significantly offset some of these emissions, but a comparison of the technologies examined revealed considerable differences. Overall, battery electric vehicles consistently outperform fuel cell electric vehicles regarding absolute greenhouse gas emissions. Hence, we recommend prioritizing battery electric over fuel cell vehicles. However, deploying fuel cell electric vehicles could become attractive in a hydrogen economy scenario where other factors, e. g. the conversion and storage of surplus renewable electricity via electrolysis, become important.

To assess the impact of a deep learning (DL) denoising reconstruction algorithm applied to identical patient scans acquired with two different voxel dimensions, representing distinct spatial resolutions. This IRB approved prospective study was conducted at a tertiary pediatric center in compliance with the Health Insurance Portability and Accountability Act. We used a General Electric Signa Premier unit (GE Medical Systems, Milwaukee, WI) to acquire two DTI sequences of the left knee on each child at 3T: an in-plane 2.0 x 2.0 mm2 with section thickness of 3.0 mm and a 2 mm3 isovolumetric voxel, neither had an inter-section gap. We used a multi-band DTI acquisi-tion with fat-suppressed single-shot spin-echo echo-planar sequence (20 non-collinear directions; b-values of 0 and 600 sec/mm2). The MR vendor-provided a commercially available DL model applied with 75% noise reduction settings to same subject DTI sequences at different spatial res-olutions. We compared DTI tract metrics from both DL-reconstructed scans and non-denoised scans for femur and tibia, at each spatial resolution. Differences were evaluated using Wilcox-on-signed ranked test and Bland-Altman plots. When comparing DL versus non-denoised diffu-sion metrics in femur and tibia using the 2 mm x 2mm x 3 mm voxel dimension there were no significant differences between tract count (p = 0.1, p =0.14) tract volume (p = 0.14, p = 0.29), or tibial tract length (p=0.16); femur tract length exhibited a significant difference (p

As the number of end-of-life vehicles continues to grow, the field of separation technology for broken copper and aluminium parts of end-of-life vehicles has emerged as a significant area of research. As a key technology for the separation of non-magnetic non-ferrous metals, such as copper and aluminium, eddy current separation can achieve efficient separation of non-magnetic non-ferrous metals according to their differing conductivity and density. Nevertheless, further research is required in the separation of large-scale broken copper and aluminium parts of end-of-life vehicles. This paper presents a novel magnetic roller model comprising circumferential and axial periodic arrangements of permanent magnets. A single permanent magnet was constructed as an equivalent current model, and the magnetic scalar potential equations were solved using simulation tools. This allowed the distribution of the magnetic field outside the magnetic roller to be studied. The results demonstrate that the novel permanent magnet array magnetic roller can enhance the magnetic field intensity and action distance of the external magnetic field, which is more conducive to the separation of large-scale broken copper and aluminium parts of scrap cars. The findings of this research provide a theoretical foundation for the separation of scrap car broken copper and aluminium parts.

China’s greenhouse industry has thousands of years of development history, although the development of modern greenhouses has come late. After decades of development of China, its greenhouse industry is in the forefront of the world. China’s greenhouse industry is experiencing rapid development, transformation and upgrading. China ranks first in the world in terms of greenhouse area, used mainly for vegetable cultivation and plays an important role in the utilization of agricultural resources and food production. In 2023, the cumulative area of new greenhouses nationwide was 1835.87 million ha. In this paper we present the latest developments in the greenhouse sector. More specifically, we present a greenhouse market development overview, the greenhouse production, the greenhouse industry, and technology development. Current problems are underpinned, development opportunities and prospects are analyzed, and measures and specific proposals are detailed for the technological development of the greenhouse sector both for increasing product quantity and quality.

In the field of railroad safety, effective detection of surface cracks is critical, necessitating reliable, high-speed non-destructive testing (NDT) methods. This study introduces a hybrid Eddy Current Testing (ECT) probe, specifically engineered for railroad inspection, to address the common issue of ’lift-off noise’ due to varying distances between the probe and test material. Unlike traditional ECT methods, this probe integrates transmit and differential receiver coils, aiming to enhance detection sensitivity and minimize lift-off impact. The study optimizes ECT probes employing different driver coils, emphasizing three main objectives: a) quantitatively evaluating each probe using signal- to-noise ratio (SNR) and outlining a real-time data processing algorithm based on SNR methodology; b) exploring the frequency range proximal to the electrical resonance of the receiver coil; c) examining sensitivity variations across varying lift-off distances. The experimental outcomes indicate that the newly designed probe with figure 8-shape driver coil significantly improves sensitivity in detecting surface cracks on railroads. It achieves an impressive SNR exceeding 100 for defects with minimal dimensions of 1 mm in width and depth. Simulation results closely align with experimental findings, validating the investigation of optimal operational frequency and lift-off distance for selected probe performance, determined to be 0.3 MHz and 0.5 mm, respectively. The realization of this project would lead to notable advancements in enhancing railroad safety by improving crack detection efficiency.

In the field of quality control, the critical challenge of analyzing microdefects in steel filament holds significant importance. This is particularly vital as steel filaments serve as reinforced fibers in the use and applications within various component manufacturing industries. This paper addresses the crucial requirement of identifying and investigating microdefects on steel filaments. Eddy current signals are used for the identification of microdefects, and an in-depth investigation is conducted. The core objective is to establish the relationship between the depth of defects and the signals detected through the eddy current sensing principle. The threshold of eddy current instrument was set at 10%, corresponding to a created depth of 20 µm, to identify defective specimens. A total of 30 defective samples were analyzed, and the phase angles between the experimental and theoretical results were compared. The depths of defects ranged from 20 to 60 µm, with one sample having a depth exceeding 75 µm. The calculated threshold of 10.18% closely aligns with the set threshold of 10%, with a difference of only 1.77%. The resulting root mean square error (RMSE) was found to be 10.53 degrees, equivalent to 3.49 µm for the difference in depth and phase between measured results and estimated results. This underscores the methodology's accuracy and its applicability across diverse manufacturing industries.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

Transportation contributes significantly to greenhouse gas emissions, with electrification offering a promising solution. This study evaluates the degradation of State of Health (SOH) over 2.5 years for electrified buses under different charging protocols: DC Fast charging and Flash charging. The vehicles’ models, charging protocols, and financial implications are discussed. High-level simulations reveal that after 2.5 years, the Flash charging vehicle’s SOH reaches 88.93%, while the DC fast charging vehicle reaches 89.46%, showing a 0.47% difference. This slight variance is attributed to Flash charging vehicles avoiding full charge/discharge cycles, reducing battery aging impact. Considering this minimal SOH degradation difference, the choice between DC Fast charging and Flash charging primarily hinges on capital expenditure disparities. Flash charging, with its lower initial battery capacity and reduced capital costs, presents a compelling alternative for city busoperators seeking to electrify their fleets.

Smart electronic devices and telemedicine are widely used in humans' daily lives. This provides remote treatment of patients using information and communications technology. New telemedicine technologies, such as the Internet of Medical Things (IoMT), make it easier for medical and computing devices to communicate regularly and effectively. Critical motivations for adapting the IoMT are reduced cost, increased quality of life, and timely medical intervention. IoMT is significant because it enables continuous, real-time patient monitoring during routine everyday activities using a variety of wearables and sensors. With big data, the IoMT technology makes excellent use of Artificial Intelligence (AI) to support disease detection and health condition prediction, alerting patients and healthcare providers. Many research studies have been conducted to explore various aspects of IoMT and its applications in the real world. However, it is challenging to comprehend all the techniques and solutions proposed by the research community. Therefore, this survey sheds light on some crucial aspects of IoMT technologies and explores the potential research gaps and directions the research community could tackle. The survey examines and discusses the characteristics of IoMT standards, protocols, and types. It then delves into the layers of IoMT and distinguishes them into Fog and edge. The studies published under each type were explored, and the limitations of these works were highlighted. The research gaps and directions on IoMT approaches and technologies were also highlighted. With such findings and research directions, further research endeavors could be carried out to address the issues and existing limitations in the IoMT.

Photovoltaic (PV) systems, which are renewable energy sources, are increasingly being utilized in distributed generation. To maintain a stable energy balance, energy storage systems such as batteries (BAT) play a vital role. Electric vehicles (EVs) offer a promising solution with rechargeable battery systems for operation. The BATs must maintain their state of charge within design boundaries, despite intermittent PV and load power fluctuations, and advanced power control and management techniques are essential for their effective operation. The article evaluates an intelligent controller that uses a Sliding Mode Control adaptive deep learning algorithm Convolutional Neural Networks (SMC-CNN) and a unique Strategy for managing supervisory power. (SPMS) for photovoltaic systems with battery energy storage for better regulation of DC bus voltage. SMC-CNN offers exceptional resilience and seamless functionality, minimizing fluctuations in DC bus voltage in the control strategy design requirements. The primary goals are maintaining a consistent power supply and ensuring continuous service by preventing system components from exceeding capacity. This study aims to enhance the control of DC bus voltage in the PV and battery system, with the primary significance focusing on the following aspects. The advanced SPMS has been created, incorporating control system constraints to enhance SOC balancing speed and reduce fluctuations in DC bus voltage. Power flow management involves optimizing energy flow between the PV system, battery system, and load while minimizing battery capacity requirements. The proposed SMC-CNN and SPMS are demonstrated through real-time simulation using Matlab/Simulink, as demonstrated in comprehensive case studies.

In this paper, an adaptive proportional and integral (PI) controller for speed control of electric drives is developed. The adaptive PI controller is designed based on model reference adaptive identification and the Lyapunov function so that the system stability can be proved. To identify the inertia, the viscous friction torque coefficient, and the load torque simultaneously and smoothly, sinusoidal speed reference is usually employed. A modified motion equation considering the low-pass filter for feedback speed and the Coulomb friction torque is introduced and the relationship between the identified parameters and their actual values are clarified. A high-precision digital simulation model is built based on MATLAB/Simulink. The effectiveness of the proposed method is verified by simulations under various conditions.

Thyroid surgery rates have tripled over the past 3 decades making it one of the most frequently performed procedures within general surgery. They are associated with the possibility of serious postoperative complications having a significant impact on the patient's quality of life. The recurrent laryngeal nerve (RLN) palsy and the external branch of the superior laryngeal nerve (EBSLN) palsy are, next to hypoparathyroidism and bleeding after operation, one of the most common complications. The introduction of neuromonitoring into thyroid surgery, enabling both confirmation of anatomical integrity and assessment of laryngeal nerve function, was a milestone that has begun a new era in thyroid surgery. The International Neural Monitoring Study Group made standardization of the technique of RLN and EBSLN monitoring during thyroid and parathyroid surgery which increased prevalence of neural monitoring during thyroidectomy. Current status of IONM and benefits of its use have been presented in this publication.

Introduction Livestock abortigenic agents, which are microorganisms that lead to premature foetal death and expulsion before completion of the gestation period, are common in Africa and Asia. Abortion events cause economic losses by lowering reproduction (and hence herd/flock sizes) and effects on milk production. Despite the importance of livestock production for food security and livelihoods of millions of the world’s poorest communities, very little is known about the scale, magnitude or causes of livestock abortion in Africa. The aim of this review was to determine the current status of the burden of livestock abortion and surveillance measures adopted for livestock abortigenic pathogens in Africa and Asia, and to explore feasible surveillance technologies. Methodology A systematic literature search was conducted using Preferred Reporting of Systematic Reviews and Meta-analyses (PRISMA) guidelines in four databases for studies published between 1 Jan 1990 and 31 July 2021 that reported epidemiological surveys of livestock abortigenic pathogens in cattle, goats and sheep in Africa and Asia including; Brucella spp., Neospora caninum, Toxoplasma gondii, Rift valley fever virus, Coxiella burnetii, Chlamydia, Leptospira and Bovine viral Diarrhoea Virus. A meta-analysis was used to estimate the species-specific prevalence of the abortigenic diseases and the region where they were detected. Results In the systematic literature search, 48 full papers were included which in total included 50 species-specific surveillance reports from Africa and 19 from Asia. Adjusted median seroprevalence calculations estimated Brucella at 6.85% (range 1.2-11.6) of 9071 sheep, 3.35% (range 0.90-5.40) of 17,007 goats, 8.95% (range 0.50-63.60) of 171,733 cattle, Neospora at 6.80% (range 6.80 -6.80) of 555 sheep, 10.80 (range 10.80-10.80) of 185 goats, 12.65% (range 3.40- 25.60) of 3775 cattle, Toxoplasma at 27.50% (range 1.40 – 75.90) of 2284 sheep, 32.0% (range 20.00- 64.80) of 1226 goats, 7.50% (range 7.50 - 7.50) of 174 cattle, Coxiella at 9.20 (range 9.20 – 9.20) of 184 sheep, 24.20% (range 24.20-24.20) of 91 goats, 13.80% (range 13.80-13.80) of 217 cattle, Rift valley fever virus at 7.70 (2.40-40.00) of 874 sheep, 20.95 (range 2.50-40.00) of 547 goats, 7.45% (range 3.60-11.30) of 309 cattle, Bovine viral diarrhea virus at 78.90 (range 78.90 – 78.90) of 398 cattle, Leptospira at 70.50 (range 70.50 – 70.50) of 373 cattle and Chlamydia at 6.60 (6.60-6.60) of 803 sheep. We found that most studies, 45 (89%) used serological surveys, 1 (2%) used molecular and 1 (2%) reported to have used Mobile-phone based surveillance approach. Three studies (6.25%) of the 48 included were embedded in the national surveillance programs of the respective countries they were conducted, majority 89% were stand-alone cross-sectional studies. Conclusion In conclusion, livestock abortigenic pathogens are still a burden in many African and Asian countries.

Drought stress severely affects the normal growth and development of wheat, leading to reduced yields and quality. To address the lag and limitations of traditional drought monitoring methods, this paper proposes a drought stress monitoring model for winter wheat during critical growth stages based on deep learning. By acquiring drought stress images of winter wheat during three critical growth stages: rise-jointing, heading-flowering and flowering-maturity, a dataset correlating these images with soil moisture monitoring data was established. The DenseNet121 network model was selected as the base network to extract phenotypic features of winter wheat under drought stress. Variables such as the model's training approach, changes in learning rate, and whether an attention mechanism was included, were used to conduct eight sets of model training and optimization strategy experiments. A drought stress monitoring model for winter wheat during critical growth stages based on an improved DenseNet-121 was constructed. The results showed that the average recognition accuracy of the eighth group in the test set reached 94.67%, indicating good application prospects in the recognition of drought stress levels during critical growth stages of wheat.

Accurate and prompt determination of fire types is essential for effective firefighting and reducing damages. However, traditional methods such as smoke detection, visual analysis, and wireless signals pose unavailability in identifying fire types. This paper introduces FireSonic, an acoustic sensing system that leverages commercial speakers and microphones to actively probe the fire using acoustic signals, effectively identifying indoor fire types. By incorporating beamforming technology, FireSonic first enhances signal clarity and reliability, thus mitigating signal attenuation and distortion. To establish a reliable correlation between fire types and sound propagation, FireSonic quantifies the Heat Release Rate (HRR) of flames by analyzing the relationship between fire heated areas and sound wave propagation delays. Furthermore, the system extracts spatiotemporal features related to fire from channel measurements. Experimental results demonstrate that FireSonic attains an average fire type classification accuracy of 95.5% and a detection latency of less than 400 ms, satisfying the requirements for real-time monitoring. This system significantly enhances the formulation of targeted firefighting strategies, boosting fire response effectiveness and public safety.

The abundant mechanical vibration energy in bridge road environment can be converted into electric energy by using the piezoelectric energy harvest technology, which could be an efficient way to provide energy required by the wireless sensor network in the bridge condition monitoring system. An autonomous energy harvesting system has been designed based on cantilever beams for sensing and acquiring the bridge vibration energy. After the analysis of the dynamic properties of the piezoelectric cantilever beam in the energy conversion, three kinds of interface circuits were compared through simulation and experimental results. It was shown that the VD interface circuit has less power loss. Furthermore, the proposed closed loop control method based on the VD circuit was simple, adaptive, and self-powered, which is suitable for the road energy harvesting application. Finally, the energy harvesting system based on VD circuit was realized with harvested power of around 0.8mW.

The gastrointestinal tract is colonized by trillions of different microorganisms, named the gut microbiota, which is key to degrade undigested food such as dietary fibers. The fermentation of these food components leads to the production of short-chain fatty acids (SCFA) acetate, propionate, and butyrate, which exploit several beneficial roles for the host’s health. Their production and absorption happen in different ways in the human intestine and depend on the type of dietary fiber reaching the gut and the microorganisms involved in the fermentation. The supplementation of SCFAs, mostly butyrate, in treating gastrointestinal, metabolic, cardiovascular, and gut-brain-related diseases has been reported in the medical literature. This review aims to give an overview of the production and absorption dynamics of acetate, propionate, and butyrate in the human gut, with a final focus on the role played by these SCFAs on gastrointestinal and metabolic health and the present therapeutic implications.

Effective oral care is important to maintain a high quality of life. Therefore, plaque control can prevent the development and recurrence of periodontitis. Brushing with a toothbrush and toothpaste is a common way to remove plaque; however, excessive brushing or brushing with abrasive toothpaste can cause wear and tear on the dental crown. Hence, we aimed to quantitatively compare the plaque-removal efficiency and tooth wear of toothbrushes using bioelectric effect (BE) with those of mechanical electric toothbrushes. To generate the BE signal, an electronic circuit was developed and embedded in a toothbrush. Further, typodonts were coated with cultured artificial plaques and placed in a brushing simulator. A toothpaste slurry was applied, and the typodonts were eluted with tap water after brushing. The plaques of the typodonts were captured, and the images were quantified. For the tooth wear experiment, polymethyl methacrylate disk resin blocks were brushed twice a day, and the thickness of the samples was measured. Subsequently, statistical differences between the experimental toothbrushes and typical toothbrushes were analyzed. The BE toothbrush had a higher plaque-removal efficiency and could minimize tooth wear. This study suggests that the application of BE may be a new solution for oral care.

Hydrogen is now recognized as the primary alternative to fossil fuels due to its renewable, safe, high energy density and environmentally friendly properties. Efficient hydrogen production through water splitting has laid the foundation for sustainable energy technologies. However, when hydrogen production is scaled up to industrial levels, operating at high current densities introduces unique challenges. It is necessary to design advanced electrocatalysts for hydrogen evolution reaction (HER) under high current densities. This review will briefly introduce chal-lenges posed by high current densities on electrocatalyst, including catalystic activity, mass dif-fusion and catalyst stability. In an attempt to address these issues, various electrocatalyst design strategies are summarized in detail. In the end, our insights into future challenges for efficient large-scale industrial hydrogen production from water splitting are presented. This review is expected to guide the rational design of efficient high current density water electrolysis electro-catalysts and promote the research progress of sustainable energy.

Fibrodysplasia Ossificans Progressiva (FOP) is an enigmatic, ultra-rare genetic disorder characterized by progressive heterotopic ossification, wherein soft connective tissues undergo pathological transformation into bone structures. This incapacitating process severely limits patient mobility and poses formidable challenges for therapeutic intervention. Predominantly caused by missense mutations in the ACVR1 gene, the disorder has hitherto defied comprehensive mechanistic understanding and effective treatment paradigms. This write-up offers a comprehensive overview of the contemporary understanding of FOP's complex pathobiology, underscored by advances in molecular genetics and proteomic studies. We shed light on targeted therapy, spanning genetic therapeutics, enzymatic and transcriptional modulation, stem cell therapies, and innovative immunotherapies. We also focused on the intricate complexities surrounding clinical trial design for ultra-rare disorders like FOP, addressing fundamental statistical limitations, ethical conundrums, and methodological advancements essential for the success of interventional studies. We advocate for the adoption of a multi-disciplinary approach that converges bench-to-bedside research, clinical expertise, and ethical considerations to tackle the challenges of ultra-rare diseases like FOP and comparable ultra-rare diseases. Overall, this article serves a dual role: as a definitive scientific resource for ongoing and future FOP research and as a call to action for innovative solutions to address methodological and ethical challenges that impede progress in the broader field of medical research for ultra-rare conditions.

This article presents a buck converter in which the inductor has been replaced by a transmission line. This approach would be practically conceivable if the power supply and load have a greater spatial distance. In the time domain, this new converter can be described by a system of coupled partial and ordinary differential equations. In the frequency domain, a transcendental transfer function is obtained. For comparison with an equivalently parameterized conventional converter, Padé approximants are derived. A linear controller is designed for the converter topology under consideration.

Among natural disasters, earthquakes have a considerable impact and are among the ten deadliest, with an extreme impact on the healthcare sector. This study aimed to analyze best practices in nursing care for earthquake victims. An in-depth analysis was carried out by using a scoping review, a method used in accordance with the PRISMA-ScR recommendations to identify best nursing practice in these circumstances based on searches of eight databases: MEDLINE via PubMed; Cochrane Library; Embase; VHL; PDQ-Evidence; Scopus; ProQuest; Google Scholar. Twenty-one studies were selected. The nursing practices identified were grouped into two distinct dimensions, each subdivided into four subcategories: (i) care practices: a) immediate care, b) intermediate care, psychosocial care and d) ethical care; (ii) care management and coordination practices, which cover (a) care coordination, (b) victim care network organization, (c) teamwork and (d) training. By analyzing these nursing practices during care and relief operations for earthquake victims, this study identified the various actions carried out, the nursing skills to be developed and the reinforcement of these advanced practices through the systematization of nurses’ skills, in order to promote victims’ rehabilitation, minimize their suffering and improving their quality of life during and after an earthquake.

The implementation of systems condition monitoring is of utmost importance in ensuring effective maintenance, optimal efficiency, and adherence to established design criteria. This research presents a novel and economically efficient Digital Twin Model (DTM) designed for the purpose of Live Condition Monitoring (LCM) and Predictive Lifecycles. This study discusses the enhancement of DTs modelling by decreasing the number of dimensions from five to three: Physical, Digital, and Connection entities. The resulting model exhibits a notable improvement in accuracy and efficiency. The suggested Dynamic Time Model (DTM) enhances the empirical pre-set average load for both simulation and experimentation by 35.7%, which is equivalent to a 1.6-fold increase. The DTM demonstrates a significant enhancement in the empirical predefined average lifecycles of the system, as shown in the real-life case study. Specifically, the DTM achieves a 12-fold improvement compared to the simulated results and a nine-fold improvement compared to the experimental findings. The suggested Dynamic Time Management (DTM) demonstrates a significant enhancement in the average lifecycles of the system, with a 19.7% improvement (equivalent to 1.2 times greater) compared to the wireless DTM results obtained through the application of the real system load. The suggested Dynamic Time Warping (DTW) method's accuracy and efficiency are shown via a practical case study using the suspension system of a Peugeot 3008 vehicle.

Hybrid electric vehicles (HEVs) are perceived as a first step towards the future of sustainable transport. Of course, battery electric vehicles (EVs) are currently ideal for what is wanted to stand for transport in the future. The lack of infrastructure for these vehicles makes many potential users choose hybrid vehicles in these conditions. This paper analyzes the influence of the engine and electric motor of hybrid vehicles on their performances. Three engines with slightly different power and close characteristics were considered for configured models. Also, two electric motors with very different power but having a very close maximum continuous torque have been used in models. One is an induction motor, and the other is a permanent magnet synchronous motor. ADVISOR software has been used for vehicles configuration and simulation. Series and parallel hybrid vehicles have been considered. The main dynamic performances and the fuel consumption in two driving cycles were compared for the configured models. Three conventional models with the same engines used in HEVs have also been simulated for reference. The results highlight that in the case of HEVs, the choice of combination engine/electric motor is crucial in obtaining the best report between dynamic performances and low fuel consumption, and implicitly a low negative impact on the environment.

A reliable and efficient rail track defect detection system is essential for maintaining rail track integrity and avoiding safety hazards and financial losses. Eddy current (EC) testing is a non-destructive technique that can be employed for this purpose. The trade-off between spatial resolution and lift-off should be carefully considered in practical applications to distinguish closely spaced cracks such as those caused by rolling contact fatigue (RCF). A multi-channel eddy current sensor array has been developed to detect defects on rails. Based on the sensor scanning data, defect reconstruction along the rails is achieved using an inverse algorithm that includes both direct and iterative approaches. In experimental evaluations, the EC system with the developed sensor is used to measure defects on a standard test piece of rail with a probe lift-off of 4-6 mm. The reconstruction results clearly reveal cracks at various depths and spacings on the test piece.

This study explores the near-surface dispersion mechanisms of contaminants in coastal waters, leveraging a comprehensive method that includes using dye and drifters as tracers, coupled with diverse observational platforms like drones, satellites, in-situ sampling, and HF radar. The aim is to deepen our understanding of surface currents' impact on contaminant dispersion, thereby improving predictive models for environmental incident management, including pollutant releases. Rhodamine WT dye, chosen for its significant fluorescent properties and detectability, along with drifter data, allowed us to investigate the dynamics of near-surface physical phenomena such as the Ekman current, Stokes drift, and wind-driven currents. Our research emphasizes the importance of integrating scalar tracers and Lagrangian markers in experimental designs, revealing differential dispersion behaviors due to near-surface vertical shear caused by the Ekman current and Stokes drift. The elongation direction of the dye patch aligns with the Ekman current direction during slow current conditions. Analytical calculations of vertical shear, based on the Ekman current and Stokes drift, closely matched those derived from tracer observations. Over a 7-hour experiment, the vertical diffusivity of near-surface water was observed at 2×10-4 m2/s, and the horizontal eddy diffusivity of the dye patch and drifters reached the order of 1 m2/s and at a 1000m length scale. Particle tracking models demonstrate that while HF radar currents can effectively predict the trajectories of tracers near the surface, incorporating near-surface currents, including Ekman current, Stokes drift, and windage, is essential for a more accurate prediction of the fate of surface floats.

Smartwatches are one of the most relevant fitness trends of the past two decades, and they collect increasing amounts of health and movement data. The accuracy of these data may be questionable and requires further investigation. Therefore, the aim of the present study is to validate smartwatches for use in triathlon training. Ten different smartwatches were tested for accuracy in measuring heart rate, distance (via global navigation satellite systems, GNSS), swim stroke rates and the number of swim laps in a 50 m Olympic-size pool. The optical heart rate measurement function of each smartwatch was compared to that of a chest strap. Thirty participants (15 females, 15 males) ran five 3-minute intervals on a motorised treadmill to evaluate the accuracy of the heart rate measurements. Moreover, for each smartwatch, running und cycling distance tracking was tested over six runs of 4,000 m on a 400 m tartan stadium track, six hilly outdoor runs over 3.4 km, and four repetitions of a 36.8 km road bike course, respectively. Three swimming protocols ranging from 200 m to 400 m were performed in triplicate in a 50 m Olympic-size pool, evaluating tracked distance and detected number of strokes. The mean absolute percentage errors (MAPEs) for the average heart rate measurements varied between 3.1% and 8.3%, with the coefficient of determination ranging from 0.22 to 0.79. MAPE results ranged from 0.8% to 12.1% for the 4,000 m run on the 400 m track, from 0.2% to 7.5% for the 3.4 km outdoor run, and from 0.0% to 4.2% for the 36.8 km bike ride. For the swimming tests, in contrast, the deviations from the true distance varied greatly, starting at a 0.0% MAPE for the 400 m freestyle and reaching 91.7% for the 200 m medley with style changes every 25 m. In summary, for some of the smartwatches, the measurement results deviated substantially from the true values. Measurements taken while road cycling over longer distances with only a few curves were in relative terms more accurate than for outdoor runs and even more accurate than for the 400 m track. In the swimming exercises, the accuracy of the measured distances was severely deteriorated by the medley changes among the majority of the smartwatches. Altogether, the results of this study should help in assessing the accuracy and thus suitability of smartwatches for general triathlon training.

Lyme disease is a highly prevalent tick-borne infection caused by Borrelia burgdorferi spirochetes in North America and Eurasia. Diagnosis of the early disease remains difficult with the currently approved serological tests in the absence of noticeable tick bite or erythema migrans due to presentation of non-specific symptoms and the absence of antibodies early in infection. Furthermore, it is difficult to distinguish persistence of disease and reinfection in the endemic regions. If not treated early, infection spreads throughout the body and affects most organs with disease manifestations including arthritis, musculoskeletal pain, neuroborreliosis and acrodermatitis chronicum atrophicans. Although most patients recover after antibiotic treatment, ~10-12% of show recurrence of symptoms known as post-treatment Lyme disease syndrome (PTLDS). Various causes of PTLDS are not well-defined; however, the spirochete persisters, antigenic debris, dysregulation of immunological response in individuals or a combination of these factors are proposed to result in continuation of Lyme disease manifestations. Based on these considerations, this review highlights currently employed treatment approaches with antimicrobials and vaccines being tried for prevention of B. burgdorferi infection. We also summarize combinatorial approaches that could be employed to alleviate symptoms to improve the quality of life of the individuals suffering from long Lyme disease.

Penile cancer (PeCa) is a rare urological malignancy characterized by significant geographic variations in both incidence and mortality rates. Due to its rarity and the consequent lack of randomized trials, current management is based on retrospective studies and small prospective trials. In addition, the diagnostic pathways and treatment strategies exhibit substantial heterogeneity, differing significantly between less developed and well-developed countries. The prognosis of PeCa is determined by the presence and extent of regional lymph node (LN) involvement. Therefore, early detection and treatment of LN metastasis is paramount to ensure better outcomes. In recent decades, the overall survival for PeCa has increased, mainly due to advancements in imaging techniques and risk stratification. We aim to provide an overview of the current role of PET CT imaging in the management of patients with PeCa.

Short-range Internet of Things (IoT) sensor nodes operating at 2.4 GHz need to provide ubiquitous wireless sensor networks (WSNs) with energy-efficient, wide-range output power (POUT) and fully integrated on a single chip for wireless body area networks (WBANs) and wireless personal area networks (WPANs) using low-power Bluetooth (BLE) and Zigbee standards. The proposed fully integrated transmitter (TX) utilizes a digitally controllable current-mode class-D (CMCD) power amplifier (PA) with a second harmonic distortion (HD2) suppression to reduce VCO pulling in an integrated system while meeting harmonic limit regulations. The CMCD PA is divided into 7-bit slices that can be reconfigured between differential and single-ended topologies. Duty cycle distortion compensation is performed for HD2 suppression, and an HD2 rejection filter and a modified C-L-C low-pass filter (LPF) reduce HD2 further. Implemented in a 28 nm CMOS process, the TX achieves a wide POUT range of from 12.1 to -31 dBm and provides a maximum efficiency of 39.8% while consuming 41.1 mW at 12.1 dBm POUT. The calibrated HD2 level is -82.2 dBc at 9.93 dBm POUT, resulting in a transmitter figure of merit (TX_FoM) of -97.52 dB. Higher order harmonic levels remain below -41.2 dBm even at 12.1 dBm POUT, meeting regulatory requirements.

During public health events, Active Mobility (walking and cycling) plays an important role in securing residents' travel. To enhance the resilience of urban transportation, this article integrates the travel environment elements for walking and cycling and constructs a travel environment for Active Mobility evaluation index system. This article uses survey data from the main urban area of Harbin in the context of the COVID-19 pandemic in May 2022, and combines the Gradient Boosting Decision Tree (GBDT) and Impact-Asymmetry Analysis (IAA) methods to analyze the satisfaction of the travel environment for Active Mobility. It proposes strategies for optimizing the travel environment for Active Mobility, ensuring residents' travel during public health events, guiding them to adopt Active Mobility, and improving urban transportation resilience. This research shows that Active Mobility can enhance urban transportation resilience. In addition, there are differences in resident demand for walking and cycling environments in the travel environment for Active Mobility. Residents are more concerned about the comfort of the walking environment, while they prioritize the convenience of the cycling environment.

This paper addresses the conceptual exploration of various issues that form an integral part of the ethical dimensions surrounding the use of artificial intelligence (AI) in the field of marketing. We critically review some of the main ethical challenges AI poses to humanity: privacy, data security, bias, transparency, and accountability. Therefore, we will discuss the delicate balance between exploiting the transformation potential of AI for personally designed marketing strategies and ethical imperatives to safeguard the rights of consumers to retain trust. Then, the present regulatory landscape responding to these ethical challenges will be assessed by building on effective regulation, like the GDPR, existing proposed legislative frameworks, and industry guidelines. To underscore the role of an ongoing dialogue between marketers, technologists, ethicists, and regulators for developing a responsible AI ecosystem in marketing. Further, strategic recommendations for implementing company-based ethical AI marketing practices. The further strong guidelines provide enhancement transparency to consumers and investment in research to remove biases from algorithms. It also underscores principal scopes of further research and development, focusing on the need for new-age solutions to guide the ethical quagmires that AI-led marketing throws up. We suggest that integration should be done proactively and collaboratively. Thus, if attention is paid more to ethics and multidisciplinary dialogue, only such hyperbolic promises can be realized by AI-driven marketing. There are such promises through which AI-driven marketing will meet business goals and be huge at societies' values.

Abstract Introduction: In the last thirty years, brain neuromodulation techniques have been used as an alternative to pharmacological treatment of neurological disorders. Parkinson's disease (PD) is a neurodegenerative disorder leading to bradykinesia, rest tremor, postural changes, and non-motor symptoms such as depression, anxiety, sleep disorders, pain, and cognitive decline that compromises executive functions (EFs), responsible for the orderly execution of behaviors and tasks of daily life and intentional and directed actions. To this date, a few studies with transcranial direct current stimulation (tDCS) have shown beneficial effects in PD patients concerning specific motor and non-motor symptoms, targeting the motor cortex and/or prefrontal regions. Objective: The main objective of this study was to evaluate the effects of left prefrontal tDCS across a broad spectrum of motor and non-motor symptoms of PD using established validated scales. Method: Single-blind randomized clinical trial with 18 volunteers with PD, aged between 45 and 80 years (66.1 ± 9.65), who met inclusion and exclusion criteria. Participants were submitted to assessments of motor and non-motor functions employing psychometric scales and tests to evaluate EFs and were randomly divided into two groups: control (sham stimulation) and experimental (active stimulation). All participants were involved in three separate tDCS sessions. The anode was positioned over the left dorsolateral prefrontal cortex and the cathode over the right supraorbital region, with a direct current intensity of 2mA, lasting 20 minutes. At the end of the three sessions, all participants were reassessed. Results: Significant effects of tDCS on non-motor functions were observed for cognition (verbal fluency of actions, clock copy test, appointment by visual confrontation, and verbal memory with immediate free recall) and subjective assessment of sleep quality (overall restlessness and discomfort in the arms and legs at night, leg and arm cramps at night and distressing dreams). There was also an improvement in the rate of errors and successes for congruent and incongruent stimuli of the Stroop Test. The beneficial effects on motor function were decreased rigidity, improved gait, and greater agility in the finger-tapping test. Conclusion: Three tDCS sessions showed positive results for participants with PD, producing significant improvements in various motor and non-motor functions, including sleep quality, cognition, and EFs. Additionally, the present results indicate that tDCS neuromodulation of the left dorsolateral prefrontal cortex region is feasible, safe, and provides significant objective benefits for PD patients.

Natural language Processing (NLP) has significantly transformed in the last decade, especially in the field of Language Modeling. Large Language Models (LLMs) have achieved SOTA performances on Natural Language Understanding (NLU) and Natural Language Generation (NLG) tasks by learning language representation in self-supervised ways. This paper provides a comprehensive survey to capture the progression of advances in Language Models. In this paper, we examine the different aspects of Language Models, which started with a few million parameters but have reached the size of a trillion in a very short time. We also look at how these LLMs transitioned from task-specific to task-independent to task-and-language-independent architectures. This paper extensively discusses different pre-training objectives, benchmarks, and transfer learning methods used in LLMs. It also examines different fine-tuning and In-Context learning techniques used in downstream tasks. It also explores how LLMs can perform well across many domains and datasets if sufficiently trained on a large and diverse dataset. Next, it discusses how, over time, the availability of cheap computational power and large datasets have improved LLM’s capabilities and raised new challenges. As part of our study, we also inspect LLMs from the lens of scalability to see how their performance is affected by the model’s depth, width, and data size. Lastly, we provide an empirical comparison of existing trends and techniques and a comprehensive analysis of where the field of LLM currently stand.

Abstract: This study investigates the effect of Electric Vehicle Charging Stations (EVCS) on light-duty Electric Vehicle sales and the Total California rebates. Electric Vehicle Charging Stations (EVCS) are infrastructure facilities that allow for the charging of electric vehicles (EVs). I applied the before and after model with California state county using its community-level attributes and used the difference-in-difference design to identify a strategy for estimating the causal effects of these attributes. These attributes include EVCS installations by time, EV sales by time, rebate applications by time, the number of multi-unit housing units, and the median income levels. The empirical ev-idence of this study shows the estimated relationship between public EV charging installation and EV sales overall by community income level, housing density, and other relevant factors, the result shows that EVCSs is highly correlated with light duty Electric Vehicle adoption. For the investors, policymakers, and other stakeholders, this study provides evidence of a threshold of EVCS on Light Duty Electric Vehicle adoption and rebate in California.

Systemic inflammation and coronary microvascular endothelial dysfunction are essential pathophysiological factors in heart failure with preserved ejection fraction (HFpEF) that support the use of statins. The pleiotropic properties of statins, such as anti-inflammatory, antihypertrophic, antifibrotic, and antioxidant effects, are generally accepted and may be beneficial in HF, especially in HFpEF. Numerous observational clinical trials have consistently shown a beneficial prognostic effect of statins in patients with HFpEF, while the results of two larger trials in patients with HFrEF have been controversial. Such differences may be related to a more pronounced impact of the pleiotropic properties of statins on the pathophysiology of HFpEF and pro-inflammatory comorbidities (arterial hypertension, diabetes mellitus, obesity, chronic kidney disease) that are more common in HFpEF. This review discusses the potential mechanisms of statin action that may be beneficial for patients with HFpEF, as well as clinical trials that have evaluated the statin effects on left ventricular diastolic function and clinical outcomes in patients with HFpEF.

The design and integration of intelligent energy management systems in hybrid Electric Vehicle (EV) charging stations, leveraging Industry 4.0 and renewable energy sources, is crucial for advancing sustainability, efficiency, and technological development. This paper introduces a pioneering hybrid EV charging station that employs hybrid power sources, combining photovoltaic panels, a battery, and a fuel cell, each operating at 240V and 14A. Utilizing wireless power transfer technology, the system comprises five integral blocks: a power source, a boost converter, a High-Frequency (HF) inverter, transfer coils, and EV batteries. The optimization process involves two key stages: i) maximum power point tracking optimization of the boost converter, ensuring maximum power generation by varying the duty cycle between 10% and 90%, and ii) the HF phase employing a class-ϕ2 inverter at 30 MHz, synchronized with the resonant frequency of wireless power transfer coils. Control is executed through a digital signal processor card utilizing zero-voltage switching for efficient operations. This design enhances sustainability in EV charging solutions by optimizing power transfer through the use of hybrid sources.

Research on early stages of corrosion of steel bars, together with the formation and development of cracks induced in the surrounding concrete and caused by chloride penetration, is relevant in improving the durability of reinforced concrete structures. This paper uses integration of the analytical models examined in the published literature, combined with experimental research in corrosion induced at the concrete/steel interface, in estimating the time-to-crack initiation of reinforced concrete subjected to corrosion. This work studies the influence of the porous network and electric current density on the cracking process at early ages. The experimental campaign was performed by using an accelerated corrosion test on a conventional concrete (CC) and a concrete with silica fume (SFC) by submitting them to a current density of 50μA/cm² and 100μA/cm². Examination performed by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) provided both qualitative and quantitative information on the penetration of the rust layer in the surrounding concrete porous network. Strain gauges were used to measure corrosion-induced deformations between steel and concrete matrices, as well as the formation of corrosion-induced cracks. A good correlation between the rate of penetration of the rust products in the surrounding pores and the delay of the cracking pressure in concrete was observed from the experimental results. This phenomenon is incorporated into the analytical model by using a reduction factor, which mainly depends on the pore size of the concrete. The crack width obtained exhibited a significant dependency on electric current density at the beginning of the test, depending mainly on the pore size of the concrete later.

Purpose of publication: - Preparation of bibliometric data exported from the Scilit platform on energy efficiency and conservation for further analysis to identify relevant research topics. - To identify potential issues in the processing of data exported from the Scilit platform. - Providing colleagues with the opportunity to use the prepared data and examples of their analysis for independent research on topical issues of energy efficiency and energy conservation using materials provided by the Scilit platform. Research Materials: Files in CSV and RIS formats exported from Scilit for the query "energy conservation OR efficiency" in Common Fields [Title, Abstract, Keyword], using filters: Content Type → Journal Article; Year→2021-2023; Subject → Industrial Engineering (29.8K), Energy and Fuel Technology (9.8K), Manufacturing Engineering (9.2K). A total of 30K records sorted by their relevance (10K for each year) were exported. Data are current as of 14-03-2024. Methods: Preprocessing of title, annotation, and keyword field texts using lemmatization dictionaries collected on GitHub, removal of keywords taken from GATE and spaCy, and "manual" editing. Using VOSviewer to analyze publication topics by clustering keywords based on their co-occurrence. Using Scimago Graphica to build bubble diagrams.Application of the GSDMM algorithm for clustering bibliometric records by title and annotation texts. Creation of a dictionary for this algorithm using the keyword field.Use of the Carrot2 demo version and the NMF algorithm for a more detailed analysis of the topics of the record clusters obtained from GSDMM. Results: are presented in the form of initial and interim tables and graphs obtained in the course of this study. The full tables are provided as references to the attached materials. Supplementary material for this preprint on figshare: Chigarev, Boris (2024). Supplementary material for preprint "Analyzing the Possibilities of Using the Scilit Platform to Identify Current Energy Efficiency and Conservation Issues". figshare. Dataset. https://doi.org/10.6084/m9.figshare.25574058.v1

An analysis of the physical and chemical phenomena accompanying the electrical discharges was carried out, principal factors inactivating microorganisms is studied. Characteristic factors of an electric discharge in cavitation mode providing a synergistic effect when disinfecting water with a discharge and chemical reagents are identified in order of importance. As a result of the integral action of cavitation, the inactivation of bacteria is intensified both due to the emergence of chem-ically active particles and due to local shock waves, acoustic currents and ultraviolet radiation in the area of cavitating bubbles. The similarity of cavitation processes in water systems implemented by underwater electric discharges and with the ultrasound has been experimentally proved. The main advantage of electric discharge cavitation in comparison with ultrasonic one is the wide band of ultrasonic frequencies of radiation inherent in electric discharge, high intensity and power of cav-itation processes, and, accordingly, the possibility of a significant increase in the volume of the disinfected liquid. The study enable better understanding and prediction of the effects that occur during a high-voltage underwater electrical discharge and have a bactericidal effect.

Pediatric onset multiple sclerosis (POMS), characterized by the onset of multiple sclerosis before the age of 18, is gaining increased recognition. Approximately 5 percent of MS cases manifest before the age of 18, with less than 1 percent occurring before the age of 10. Despite its rarity, pediatric MS exhibits distinct characteristics, with an association between younger age at onset and a comparatively slower disease progression. Despite this slower progression, individuals with POMS historically reach disability milestones at earlier ages than those with adult-onset multiple sclerosis. While various immunomodulatory agents demonstrate significant benefits in MS treatment, such as reduced relapse rates and slower accumulation of brain lesions on magnetic resonance imaging (MRI), the majority of disease-modifying therapies (DMTs) commonly used in adult MS lack evaluation through pediatric clinical trials. Current evidence is predominantly derived from observational studies. This comprehensive review aims to consolidate existing knowledge on the mechanisms of action, efficacy, safety profiles, and recommended dosages of available DMTs specifically in the context of pediatric MS. Furthermore, the review outlines recent advancements and explores potential medications still in developmental stages, providing a thorough overview of the current landscape and future prospects for treating POMS.

Transitioning to clean cooking fuels is not only part of achieving SDG7, but also makes a significant contribution to mitigating climate change by reducing carbon emissions. The paper contradicts the conventional wisdom that electricity is too expensive to cook with. The paper explores the energy required to cook dishes using different technologies and fuels by analysing data from Cooking Diaries and Controlled Cooking tests conducted under the MECS programme. Electric pressure cookers (EPCs) use least energy when compared with electric hotplates, and a detailed description of how the EPC works explains why this should be. The paper draws out distinctions between African and Asian dishes, notably the impact of energy intensive dishes prepared mostly in Africa. Standard efficiency based approaches to comparing the performance of stoves are not appropriate to modern electric cooking devices so an alternative approach based on specific energy consumptions is proposed e.g. charcoal stoves use 15 times as much energy as EPCs to cook African dishes. Energy ratios provide a basis for estimating carbon emission reductions associated with transitioning to modern cooking fuels. Historical costs show that the cost of cooking with an EPC can be only 20% of the cost of cooking with charcoal, which highlights the potential for modern, energy efficient electric cooking devices to defy the conventional wisdom of the energy ladder.

The therapeutic, attenuative, and morphological effects of proprietary neural stem cell-derived extracellular vesicles (NSC EVs, AB126) produced by Aruna Bio, Inc. were assessed in a range of in vitro and in vivo models of stroke. We emphasize that modulation of neuroinflammation is a key target and suggest further studies to advance our understanding of the mechanisms of action and ultimately how best to dose and monitor the benefits of AB126 in stroke patients.

This narrative review examines the crucial role of physical activity in managing long COVID, characterized by persistent symptoms such as fatigue, breathlessness, and cognitive impairments following SARS-CoV-2 infection. The methodology involved a comprehensive literature search across PubMed, EBSCO (EDS), and Google Scholar, selecting peer-reviewed articles from December 2019 focusing on long-term COVID physical activity interventions. The review highlights that tailored exercise programs, adjusted to individual health status and abilities, significantly alleviate symptoms and enhance psychological well-being. Key findings emphasize the importance of personalized exercise prescriptions due to the variability in patient responses and the need for a multidisciplinary approach in developing and monitoring interventions. Despite promising outcomes, the review identifies research gaps, including the need for long-term studies, randomized controlled trials, and deeper mechanistic insights. It suggests that standardized reporting, templates like CERT, and integrating digital health tools are essential for optimizing interventions. Overall, the review advocates including personalized physical activity programs in standard care for long COVID to improve patient outcomes and quality of life.

Purpose of review The forest industry has deployed ICTs to improve productivity of forest supply chains. In this sense, digitalization of data flows significantly impacts wood supply chains, from forest to mills, which must react flexibly to market fluctuations of forest products. The goal of this study was to conduct a literature review on data flow implementations in management systems of wood supply chains and to evaluate their applicability in supply chains to analyze the opportunities for improving them in practice. Recent findings We utilized the ScienceDirect database, Scopus and Web of Science in order to document data flows in systems and actual applications. Due to ongoing outsourcing, the wood procurement chains, and the wood supply chains were identified in the forest industry. Several different technologies can be implemented also in wood supply chains to digitalize the data flow depending on the specific needs of organizations. In this regard, digitalization of Big Data causes significant changes in elements of supply models that should be integrated and standardized in the optimization and simulation systems. Summary A modelling guide is suggested for accurate dynamic solution of problems of forest logistics. Then, the opportunities in digitalization for connecting different data flows, technologies, and stakeholders are discussed thoroughly. We conclude that data-driven dynamic optimization, and locally implemented digitalization contributes to wood supply modeling in the establishment of standards for cloud-based platforms at time-related and sequential measures which will ensure successful forest logistics through the planning and the monitoring of wood supply chains.

Day by day, the share of renewable energy-based power plants such as offshore wind farms and photovoltaic power plants, in the present-day power systems is escalating. Nevertheless, most of these power-producing facilities have been located quite far away from the load centers. At this stage, HVDC power systems provide satisfactory options due to qualities such as reduced line losses, substantial controllability, and environmental advantages. Nevertheless, unique converter designs are required to combine asynchronous HVDC networks with each other and with already existing high voltage alternating current (HVAC) networks. In this study, based on the above special cases, a unique DC-DC modular multilevel converter (MMC) architecture is presented that provides an excellent solution for both integrating modern asynchronous HVDC networks and integrating these modern HVDC power systems with existing asynchronous HVAC power systems. The mathematical analysis of the recommended DC-DC MMC design has been examined in detail and the power transfer between two asynchronous power grids has been realized in a simulation environment. Efficient bilateral power transmission has been made achievable by the control system. The recommended DC-DC MMC topology has shown to be a highly successful approach, in the interconnection of HVDC power systems, according to the simulation results.

Abstract: Lipidic carriers employed for the entrapment, encapsulation and precise targeting the bioactive compounds offer significant advantages to the biomedical, pharmaceutical, nutraceutical and cosmeceutical industries. These lipid and phospholipid-based vesicles can improve the solubility, permeation, pharmacokinetics, pharmacodynamics and bioavailability of the encapsulated material. As a matter of fact, nano-sized phospholipid vesicles have attained the highest success rate in commercialization among the available drug encapsulation technologies. Nevertheless, developing industrially acceptable products still remains a challenge. Among the main disadvantages of conventional lipidic carriers are their instability in the biological environments, and their sensitivity to changes in the pH, temperature and enzymes. To overcome these problems, the new generation of phospho/lipid-based carrier systems was developed using ingredients from microorganisms living in extremely harsh environments (i.e., archeaeobacteria). The present entry aims to review unique features of archaeolipids and recent developments in their application for the encapsulation of genetic material as well as their role and function as adjuvants and vaccine candidates.

Hyperuricemia (HU), characterized by elevated uric acid (UA) levels in the blood, represents a global health concern associated with various conditions, including cardiovascular diseases, gout, hypertension, metabolic syndrome, renal dysfunction, and neurodegenerative diseases. This review offers a contemporary analysis of HU, encompassing its causes, associated health risks, diagnosis, treatment, and future outlook. Recent studies have underscored the multifaceted origin of HU, implicating genetic predisposition, dietary patterns, lifestyle choices, and environmental influences. Genetic variations affecting enzymes and transporters involved in purine metabolism and UA excretion have been identified, laying the groundwork for personalized treatment strategies. Advances in diagnostic imaging and omics technologies provide enhanced precision in the detection and evaluation of risks. While pharmacological interventions remain central to managing HU, persistent challenges such as treatment resistance prompt exploration of novel drug targets and lifestyle modifications. Chinese herbal medicines offer a potentially alternative approach with fewer side effects. Emerging research on the impact of gut microbiota on UA metabolism opens new therapeutic avenues. Despite progress, challenges such as optimizing treatment duration and understanding long-term effects persist. Collaborative efforts are crucial to address these challenges and advance our comprehension of HU. The integration of precision medicine and holistic patient care approaches holds promise for improving outcomes and enhancing quality of life for individuals with HU.

The European Union Water Framework Directive (2000/60/EC; WFD) aims to achieve a good ecological and chemical status of all bodies of surface water by 2027. The development of an integrated guidance on surface water chemical monitoring (e.g. WFD Guidance Document No. 7/19) has been transferred into national German law (Ordinance for the Protection of Surface Waters, OGewV). For the majority of compounds, this act requires a monthly sampling frequency to assess the chemical water quality status of a surface water body. To evaluate the representativeness of the sampling strategy under the OGewV, high-frequency online monitoring data is investigated under different sampling scenarios and compared with current, monthly grab sampling strategy. About 23 million data points were analyzed for this study, three chemical parameters (dissolved oxygen, nitrate-nitrogen, chloride concentration) and discharge data were selected from four catchment of different sizes ranging from 51391 km² to 84 km² (Elbe, Vereinigte Mulde, Neiße and two stations at Lockwitzbach). In this paper we proposed short-term online-monitoring (STOM) as a sampling alternative. STOM considers the placement of online sensors over a limited duration and return interval. In general we: (I) compare the results of conventional grab sampling with STOM, (II) investigate the different performance of STOM and grab sampling using discharge data as proxy for analyzing event-mobilized pollutants and (III) investigate the related uncertainties and costs of both sampling methods. Results show, that STOM outperforms grab sampling for parameters where minimum/maximum concentrations are required by law as the probability to catch a single extreme value is higher with STOM. Furthermore, parameters showing a pronounced diurnal pattern, like dissolved oxygen, are also captured considerably better. The performance of STOM showed no substantial improvements for parameters with small concentration variability, as nitrogen-nitrate The analysis of discharge events as a proxy parameter for event-mobilized pollutants proved that the probability of capturing samples during events is significantly increased by STOM.

Responding to changing value creation processes in the sheet metal working sec-tor, where the complexity and interchangeability of products challenge traditional dif-ferentiation strategies, this empirical analysis explores integrating service-oriented and data-driven business models as new paths to ensure competitiveness, especially for small and medium-sized enterprises (SMEs). This study aims to capture the current state and challenges associated with the implementation of these business models in this sector. The research was conducted through semi-structured interviews with SMEs in the industry. The findings indicate that service-oriented and data-driven business models are not yet widely adopted and that manufacturing companies re-quire support in their implementation. Fields of action were identified for the industry. These are "Creating awareness and understanding", "Recognizing added value", "In-creasing company maturity" and "Understanding the change process". Cooperation between science and industry is essential in tackling these fields of action to ensure the successful integration of such business models in manufacturing companies. This pa-per identifies challenges in the fields of action that companies must address through a structured approach promoting awareness, recognizing value, improving organiza-tional maturity, and understanding the change process to successfully implement ser-vice-oriented and data-driven business models.

To harness light-matter interaction at nano-/micro-scale better control tools have to be developed. Here, it is shown that by applying external electric and/or magnetic field, ablation of Si and glass under ultra-short (sub-1~ps) laser pulse irradiation can be controlled via the Lorentz force $\mathbf{F} = e\mathbf{E} + e[\mathbf{v}\times\mathbf{B}]$, where $\mathbf{v}$ is velocity of charge $e$, $\mathbf{E}$ is the applied electrical bias and $\mathbf{B}$ is the magnetic flux density. The external electric E-field was applied during laser ablation using suspended micro-electrodes above glass substrate with an air gap for the incident laser beam. The counter-facing Al-electrodes on Si surface were used to study debris formation patterns on Si. Debris was deposited preferentially towards the negative electrode in the case of glass and Si ablation. Also, an external magnetic field was applied during laser ablation of Si in different geometries and is shown to affect ripple formation. The vectorial nature of the Lorentz force widens application potential of surface modifications and debris formation in external E-/B-fields with potential applications in mass and charge spectroscopes.

The high figure of merit and earth abundance of Cu₁₂Sb₄S₁₃ thermoelectric ma- terials have recently attracted many attentions toward these type of complex compounds. Intrinsic low thermal conductivity, as well as tunable electronic transport properties, make them suitable for thermoelectric power generation. In this study, we perform a comparative theoretical study on the substituted compounds, primarily at the Cu site including known tetrahedrite Cu₁₂Sb₄S₁₃, by means of first-principles calculations. The density functional theory of electric structure is applied to investigate the result of substitution.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

In steel recycling, the optimization of electric arc furnaces (EAFs) is of central importance in order to increase efficiency and reduce costs. This study focuses on the optimization of electric arcs, which make a significant contribution to the energy consumption of EAFs. A three-phase equivalent circuit integrated with the Cassie-Mayr arc model is used to capture the nonlinear and dynamic characteristics of arcs, including arc breakage and ignition process. A particle swarm optimization technique is applied to real EAF data containing current and voltage measurements to estimate the parameters of the Cassie-Mayr model. A novel Arc Quality Index (AQI) is introduced in the study, which can be used to evaluate arc quality based on deviations from optimal conditions. The AQI provides a qualitative assessment of arc quality, analogous to indices such as arc coverage and arc stability. The study concludes that the AQI serves as an effective operational tool for EAF operators to optimize production and increase the efficiency and sustainability of steel production. The results underline the importance of understanding electric arc dynamics for the development of EAF technology.