This study aims to investigate the interfacial tension, emulsion stability, and the impact on oil displacement effectiveness of mixed systems containing nonionic surfactants and amphoteric surfactants at different ratios. To achieve this, three different emulsion stability formulations were prepared by mixing betaine and nonionic surfactants in ratios of 1:1, 3:2, and 3:1 respectively. By adjusting the proportions of betaine and nonionic surfactants, variations in interfacial tension and emulsion formation among the three mixed systems were studied to analyze the mechanism of interaction between betaine and nonionic surfactants and evaluate their effects on crude oil displacement and enhanced oil recovery in reservoirs. Subsequently, microscopic and macroscopic oil displacement experiments were conducted on the three mixed systems, along with experiments on emulsion flow resistance. The aim was to verify the oil displacement effectiveness of different mixed systems and further understand their potential applications in reservoirs. By comprehensively analyzing the experimental results, optimal ratios and conditions for the mixed systems were determined. The experimental results indicate that the emulsification system formed by mixing betaine and nonionic surfactants at a ratio of 3:1 achieves molecular synergies through electrostatic interactions and mixed adsorption with betaine, resulting in a compact arrangement of interface membranes and demonstrating a synergistic effect in reducing interfacial tension to an ultra-low value of 10 -4 mN/m. Additionally, as the proportion of betaine surfactant increases, the viscosity of the aqueous phase liquid film increases, the rate of thinning of the liquid film slows down, the rate of water release slows down, and the stability of the emulsion increases. Microscopic oil displacement experiments verified that the three mixed systems increase oil washing efficiency through low interfacial tension and emulsification stripping action, thereby increasing the oil displacement mechanism's coefficient. Emulsion flow resistance experiments demonstrated that as the proportion of betaine surfactant increases, the system exhibits better plugging ability. However, macroscopic oil displacement experiments revealed differences in compatibility between different emulsion stability solutions and rocks with different permeabilities. The mixed system of betaine and nonionic surfactants at a ratio of 3:1 exhibits the best emulsification plugging ability in rocks with a permeability of 109mD, while the 1:1 mixed system performs best in rocks with a permeability of 12mD. This holds significant theoretical and practical significance for reservoir development and enhanced production.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

Emphasizing the importance of acoustic attenuation in maintaining compliance with stringent noise regulations and enhancing workplace safety, the analysis covers the theoretical and practical aspects of sound attenuation in a turboengine testing stand. This paper presents a preliminary analysis and also an evaluation of a procedure for projecting a noise attenuator for industrial application and especially for turboengine test stands. While primarily focusing on the static acoustic behavior of the attenuator, considerations were also made regarding flow dynamics, Mach number-dependent attenuation, pressure drop, and self-generated noise aspects to provide a comprehensive perspective in selecting the optimal design configuration. The study investigates different calculation methods for assessment of the noise reduction for linear and staggered baffles, applied on a scaled reduced model of attenuator. Thus, the critical parameters and projecting requirements necessary for effective noise reduction in high-performance turboengine testing environments will be evaluated in a down-scaled model. Key factors examined include the selection of design parameters and configurations from various options. Advanced computational methods, like analytic and finite element analysis (FEM) are utilized to predict the acoustic performance and identify potential design optimizations. Experimental validation is performed to corroborate the simulation results, ensuring the reliability and efficiency of the attenuator. The findings indicate that a well-designed sound attenuator module can significantly reduce noise levels without compromising the operational performance of the turboengine inside a test cell.

Gas-water relative permeability curve is the foundation of gas reservoir dynamic analysis and numerical simulation. It is generally obtained through gas displacing water experiment. Referring to the existing national standards, gas-water relative permeability test is carried out for low-permeability and tight sandstone. The flow is discontinuous and the curve smoothness is poor, which affects the application of gas-water relative permeability curve. Based on the comparative analysis of a large number of mercury injection and NMR experimental results of low-permeability and tight sandstone, a method to characterize the throat radius distribution of low-permeability tight sandstone based on NMR T2 spectrum is explored. Combined with high-speed centrifugal experiment, the calculation formulas of core water saturation, phase relative permeability of gas-water under different centrifugal force are established. A new method of "nuclear magnetic resonance + high-speed centrifugation" for gas-water relative permeability curve test of low-permeability and tight sandstone is formed, and the test is carried out on Sulige low-permeability tight sandstone core. The results show that: (1) The shape of cumulative distribution curve of throat radius by mercury injection method is basically consistent with that of T2 relaxation time by NMR, and there is a good corresponding relationship between them. (2) The centrifugation process is similar to the gas displacing water process. With the decrease of water saturation, water centrifugation in rock core becomes more and more difficult until it become irreducible. (3) The test process of the new method is unified and standard and up to 6 cores can be tested at the same time. The calculation results of water saturation and relative permeability curve are reliable and the integral curve is smooth, which greatly improves the test efficiency of gas-water relative permeability curve in low-permeability and tight sandstone. The new method can be widely used to study the gas-water two-phase seepage law in low-permeability and tight sandstone gas reservoir.

In the realm of metal steel and iron manufacturing, there is a constant drive to optimize production efficiency and enhance the quality of the final products. This abstract explores a paradigm shift in this industry through the utilization of Computational Fluid Dynamics (CFD) as a powerful tool for achieving these goals .The study focuses on various critical aspects of the manufacturing process. Firstly, it delves into three-phase processes such as slag and gas entrainment in liquid steel, which have a significant impact on the overall product quality. Understanding and optimizing these processes is crucial to ensure the desired chemical composition and physical properties of the final metal.The abstract investigates the role of CFD in vacuum degassing, a process that plays a pivotal role in removing impurities, such as hydrogen and oxygen, from the liquid steel. By leveraging CFD to simulate and analyze the fluid flow patterns, researchers and engineers can design more efficient vacuum degassing systems, leading to improved product purity and reduced waste.Another crucial aspect explored in this abstract is the alloy melt and mixing process. By employing CFD simulations, researchers can gain insights into the movement of different alloy components and optimize their distribution within the melt. This aids in achieving the desired alloy composition, ensuring uniformity, and enhancing the mechanical properties of the final product.In addition, the study delves into the movement and flotation of inclusions, which are unwanted impurities present in the metal. CFD can be utilized to model and analyze the behavior of these inclusions, enabling engineers to design efficient strategies for their removal, thereby enhancing the purity and integrity of the final product.Moreover, the abstract considers the impact of melt temperature losses, which can occur during different stages of the manufacturing process. By employing CFD, it becomes possible to understand and mitigate these temperature losses, leading to improved energy efficiency and better control over the manufacturing parameters.Part 1 of this abstract critically evaluates the use of CFD in iron making, analyzing its benefits and limitations. It highlights how CFD can aid in process optimization, improving the understanding of complex phenomena involved in iron making, and ultimately leading to enhanced production efficiency.Part 2 focuses on the application of CFD in steel making and steel operation. It explores the fluid flow dynamics during different stages of steel production, including refining, casting, and rolling. By leveraging CFD, engineers can optimize these processes, leading to improved product quality, reduced defects, and increased productivity.This abstract demonstrates the transformative potential of Computational Fluid Dynamics in metal, steel, and iron manufacturing. By utilizing CFD as a tool to model and analyze complex fluid flow phenomena, researchers and engineers can revolutionize the production process, maximizing efficiency, and ensuring high-quality end products.

Driven by mounting environmental apprehensions stemming from the over dependence on fossil fuels in energy and transportation sectors, extensive exploration into alternative energy sources, particularly biomass, has stimulated profound research on harnessing the potential of computational and mathematical techniques. This comprehensive survey delves into optimal models and strategies, unveiling their pivotal role in the design of biomass gasification processes.of hydrogen through biomass gasification. In this study, we aim to provide a comprehensive overview of the computational and mathematical techniques employed in optimizing biomass gasification processes, with a specific focus on enhancing hydrogen yield. Through an extensive literature review, various models and strategies will be examined, including thermodynamic analysis, kinetic modeling, reactor design, and process optimization. By uncovering the power of these techniques, we aim to contribute to the advancement of sustainable and efficient biomass utilization for the hydrogen-based future economy.This paper aims to provide an updated and comprehensive coverage of the investigations conducted on the potential of producing hydrogen from biomass through gasification. To achieve this, we incorporate the latest works that have utilized numerical modeling, simulation, optimization techniques, process heat integration, and co-generation in their studies. By encompassing these aspects, we aim to offer a broader and more in-depth re-appraisal of the subject matter. This will ensure that readers gain a holistic understanding of the advances made in the field and the potential for sustainable hydrogen production of biomass gasification.Through a meticulous re-appraisal and analysis of each subject, we can identify their respective strengths and areas that require further research effort. By thoroughly examining numerical modeling, simulation, optimization techniques, process heat integration, and co-generation, we can assess their effectiveness and applicability in the context of biomass gasification for hydrogen production. This analysis shed light on the areas where these techniques excel, as well as pinpoint limitations or gaps in current understanding. By identifying these areas, we can highlight the need for further research and development, enabling us to make significant advancements in biomass gasification processes and pave the way for a sustainable and efficient hydrogen-based future economy..

Carbon dioxide (CO2)miscible fracturing huff and puff technology plays a pivotal role in enhancing the recovery rate of crude oil, particularly in reservoirs with challenging physical properties, strong water sensitivity, high injection pressure, and complex water injection dynamics. In this study, the oil-increasing mechanism and huff and puff effect of CO2 miscible fracturing fluid are investigated through a comprehensive experimental approach. Specifically, experiments on PVT gas injection expansion, minimum miscible pressure, and CO2 miscible fracturing huff and puff are conducted on the G fault block reservoir in J Oilfield. The findings demonstrate that injecting CO2 into reservoirs leads to oil volume expansion, viscosity reduction, and saturation pressure increase. Additionally, the inclusion of solubilizers and viscosity reducers further enhances the efficiency of crude oil extraction. Solubilizers not only improve oil recovery but also reduce the minimum miscible pressure required for effective CO2 dispersion. Furthermore, the shut-in time, permeability, and huff and puff method all have considerable impacts on huff and puff recovery rate. This study offers valuable technical insights, supporting the application of CO2 miscible fracturing huff and puff technology to enhance oil recovery in low-permeability reservoirs.

The erosion of surface pipelines induced by proppant flowback during shale gas production is significant. The surface pipelines in a shale gas field in the Sichuan Basin experienced perforation failures after only five months of service. To investigate the erosion features of L360N, coatings, and ceramics and optimize the selection of two protective materials, a gas-solid two-phase flow jet erosion experimental device was used to explore the erosion resistance of L360N, coating, and ceramic under different impact velocities (15 m/s, 20 m/s, and 30 m/s). An energy dispersive spectroscope, a scanning electron microscope, and a laser confocal microscope were employed to analyze erosion morphologies. With the increase in flow velocity, erosion depth and erosion rate of L360N, coating, and ceramic increased and peaked under an impact velocity of 30 m/s. Maximum erosion rate and maximum erosion depth of L360N were respectively 0.0350 mg/g and 37.5365 µm. Its primary material removal mechanism was plowing of solid particles and microcracks were distributed on the material surface under high flow velocities. Maximum erosion rate and maximum erosion depth of coating were respectively 0.0217 mg/g and 18.9964 µm. Its primary material removal mechanism was the detachment of the binder phase Co caused by plowing. Maximum erosion rate and maximum erosion depth of ceramics were respectively 0.0108 mg/g and 12.4856 µm. The erosion mechanisms were micro-cutting and plowing. Under different particle impact velocity, different erosion morphologies were observed, but the primary erosion mechanism was the same. The erosion resistance of ceramics was higher than that of coating. Therefore, ceramic lining materials could be used to protect the easily eroded parts, such as pipeline bends and tees, and reduce the failure rate by more than 93%. The study provided the data and theoretical basis for the theoretical study on oil and gas pipeline erosion and pipeline material selection.

Pore structure characterization and fractal analysis have great significance for understanding and evaluating tight limestone reservoirs. In this work, the pore structure of tight limestone is characterized combined with low-temperature nitrogen adsorption (LTNA) and low-field nuclear magnetic resonance (NMR), and the fractal dimension of tight limestone pore structure is discussed based on LTNA and NMR data. The results indicate that the pores of tight limestone have H3 and H4 types, the pore size distribution (PSD) of H3 type is a wave distribution ranging from 2 to 10 nm, and the PSD of H4 type is a unimodal distribution ranging from 2 to 10 nm. The transverse relaxation time (T2) spectrum of tight limestone shows single peak (DF), double peak (SF) and three peak (TF), and the T2 spectrums for micropores, mesopores and macropores range from 0.1 to 10 ms, from 10 to 100 ms, and greater than 100 ms, respectively. The LTNA fractal dimension of tight limestone (DL) ranges between 2.4446 and 2.7688, with an average of 2.5729, and the NMR fractal dimensions of micropores (DNMR1), mesopores (DNMR2) and macropores (DNMR3) are distributed between 0.3744 to 1.1293, 2.4263 to 2.9395 and 2.6582 to 2.9989, respectively. Moreover, there is no correlation between fractal dimension and permeability and porosity, a negative correlation between DL and average pore radius, a positive correlation between DL and specific surface area, and a positive correlation between DNMR2 and DNMR3 and micropore content, while DNMR2 and DNMR3 are negatively correlated with the content of mesopores and macropores.

Background. Keyword co-occurrence analysis is a crucial tool for comprehending research trends, identifying relevant studies, and gaining insight into the connections between various concepts and topics. Objective. This study focuses on analyzing the co-occurrence of keywords using FP-growth algorithm and direct search methods. Materials and methods. The methodology involved extracting bibliometric data of Energies journal for 2023-2024 from MDPI publisher platform, keyword lemmatization and keyword co-occurrence estimation. Clustering and visualization were performed using Multidendrograms and Scimago Graphica software. Results. The results showed that the FP-growth algorithm can achieve a close match with the direct search results, which facilitates data preparation for clustering. In addition, finding the co-occurrence of three or more keywords significantly reduced the number of possible combinations, which allowed the identification of specific research topics. Conclusions. This study highlights the usefulness of the FP-growth algorithm in keyword analysis and provides insights into ways to refine search queries to abstract databases for the purpose of designing and writing literature and systematic reviews.

Relevance of the subject. Keyword selection is critical to finding relevant literature and requires justification for querying abstract databases and other sources to ensure accuracy and completeness. The topic of Energy Systems is of great importance due to the introduction of renewable energy sources, modern control methods, and complex energy systems during the energy transition. The aim of this study. The goal of this paper was to identify keywords that would be useful to subject matter experts when collecting literature on a particular topic, based on entries in the IEEE Terms field. Data. Bibliometric data were exported from the IEEE Xplore platform in the following order: for 2019-2023, 2000 records sorted by relevance, for 2024, 1680 records current as of April 11, 2024. Analytical methods applied and software used. VOSviewer, Scimago Graphica implementing the Clauset-Newman-Moore algorithm and agglomerative hierarchical clustering method implemented in Multidendrograms. Results. The main issues of the Energy Systems topic are presented in tabular and graphical formats. The fpgrowth utility offers flexible data preparation options, which makes it worthwhile to conduct a separate study to analyze the score of co-occurrence terms given by its algorithm.

Purpose of publication: - Preparation of bibliometric data exported from the Scilit platform on energy efficiency and conservation for further analysis to identify relevant research topics. - To identify potential issues in the processing of data exported from the Scilit platform. - Providing colleagues with the opportunity to use the prepared data and examples of their analysis for independent research on topical issues of energy efficiency and energy conservation using materials provided by the Scilit platform. Research Materials: Files in CSV and RIS formats exported from Scilit for the query "energy conservation OR efficiency" in Common Fields [Title, Abstract, Keyword], using filters: Content Type → Journal Article; Year→2021-2023; Subject → Industrial Engineering (29.8K), Energy and Fuel Technology (9.8K), Manufacturing Engineering (9.2K). A total of 30K records sorted by their relevance (10K for each year) were exported. Data are current as of 14-03-2024. Methods: Preprocessing of title, annotation, and keyword field texts using lemmatization dictionaries collected on GitHub, removal of keywords taken from GATE and spaCy, and "manual" editing. Using VOSviewer to analyze publication topics by clustering keywords based on their co-occurrence. Using Scimago Graphica to build bubble diagrams.Application of the GSDMM algorithm for clustering bibliometric records by title and annotation texts. Creation of a dictionary for this algorithm using the keyword field.Use of the Carrot2 demo version and the NMF algorithm for a more detailed analysis of the topics of the record clusters obtained from GSDMM. Results: are presented in the form of initial and interim tables and graphs obtained in the course of this study. The full tables are provided as references to the attached materials. Supplementary material for this preprint on figshare: Chigarev, Boris (2024). Supplementary material for preprint "Analyzing the Possibilities of Using the Scilit Platform to Identify Current Energy Efficiency and Conservation Issues". figshare. Dataset. https://doi.org/10.6084/m9.figshare.25574058.v1

The gas-water relative permeability curve plays a crucial role in reservoir simulation and development for condensate gas reservoirs. In this study, we conducted a series of high temperature and high pressure analysis experiments on real gas cores from Wells A and B in Block L of the Yinggehai Basin to investigate the effects of temperature, pressure, and different types of gas media on gas-water seepage. The experimental results demonstrate that: Temperature has a significant impact on both gas and water relative permeability, particularly on the former. As temperature increases, gas relative permeability shows a substantial increase while water relative permeability remains relatively unchanged. Under the same effective stress, increasing pressure causes downward shifts in both the gas and water relative permeability curves; however, there is a more pronounced decrease in gas relative permeability. Gas type has minimal influence on phase permeability except at higher water saturation where differences become apparent. When water saturation ranges from 80% to 50%, there is no significant variation observed in the measured relative permeability of different displacement gases; however, as water saturation exceeds 80%, distinctions gradually emerge. At bound water saturation conditions, nitrogen exhibits lower relative permeability compared to simulated gases with approximately 92% similarity between them. This investigation into the characteristics of gas-water relative permeability in high temperature and high pressure condensate reservoirs within Yinggehai Basin provides valuable insights for efficient development strategies for similar reservoirs.

This study presents the evaluation of an ion exchange resin-based installation designed for the recycling of engine coolants, specifically ethylene glycol (EG) and propylene glycol (PG). The recycling process aims to restore the coolant to meet the stringent ASTM standards for both new and recycled coolants. A combination of physical-chemical methods, gas chromatography-mass spectrometry (GC-MS), and inductively coupled plasma mass spectrometry (ICP-MS) was employed to analyze and validate the purity and performance of the recycled product. The experimental setup included performance tests to assess the efficacy of the recycled coolants in comparison to new coolant standards. The results demonstrate that the recycled EG coolants exhibit comparable quality to new coolants, with all critical parameters falling within the acceptable ASTM limits. This indicates that the ion exchange resin method is a viable and efficient solution for the recycling of engine coolants, offering an environmentally friendly alternative to the disposal of used coolants while ensuring compliance with industry standards.

Developing a dependable gas and condensate value chain is vital for the ongoing prosperity of the oil and gas industries. To achieve this, NNPC is enhancing its production facilities by employing process modeling and simulation with the assistance of Symmetry iCON®. As a part of this initiative, a simulation model was created using the Symmetry iCON® pipe plexus solver to simulate the dynamic environment of the gas and condensate pipeline network in the Nigerian Southern region. To validate the model, data from a single month, specifically December 2022, was utilized. Furthermore, the algorithm was utilized to generate projections for the month of January 2023, providing valuable insights into its effectiveness. The study also highlighted the significance of accurately estimating the characteristics and properties of a pseudo component of C6+ in relation to thermodynamics and material properties, which was a particularly insightful finding. he assessment of this property has transitioned from being relatively unimportant to becoming critically important, primarily due to the lack of condensate data monitoring at specific terminals. However, it's worth noting that the model currently has an error margin of 4-6% when predicting the data. As more information becomes available in the future, the model can be easily fine-tuned to better align with the actual conditions, allowing for more accurate predictions.

The article presents the results of the technical-economical study regarding the optimization of the FDM parameters (Lh – the height of the layer deposited in one pass and Id – the filling percentage) for the manufacture of PETG and ASA parts. To carry out the technical-economical study, we used the fundamental principle of value analysis, which consists in maximizing the ratio between Vi/Cp, where Vi - represents the mechanical characteristic, and Cp - represents the production cost. The results of the study show that for the tensile specimens made of PETG, the parameter that significantly influences the results of the Vi/Cp ratios is Lh, and in the case of the compression specimens made of PETG, the parameter that significantly influences the results of the Vi/Cp ratios is Id. In the case of specimens manufactured by FDM from ASA, the parameter that decisively influences the results of the Vi/Cp ratios of the tensile and compression specimens is Id – the filling percentage. By performing optimization of the process parameters with multiple responses, we identified the optimal parameters for FDM manufacturing of parts from PETG and ASA: Lh = 0.20 mm and Id = 100%.

In order to establish the formation patterns of the Co–Mg oxide system, samples with different Co:Mg ratios and heat treatment temperatures were synthesized and studied. Study of the sam-ples confirmed the phase transition of MgxCo2–xO4 spinels into corresponding solid solutions at 800–900 °C. The similarity of formation patterns for different compositions is shown. The rock-salt oxide in low-temperature samples is an anion-modified paracrystalline phase that forms a “true” solid solution only upon spinel decomposition. TPR profiles of decomposed Co3O4 spinel show surface Co3O4 peaks and a wide peak corresponding to well-crystallized CoO, while par-tial Co3O4 TPR up to 380 °C results in dispersed and amorphous CoO. High-temperature non-stoichiometric samples are poorly reduced, indicating their low oxygen reactivity. Spinel reoxidation after heat treatment to 1100 °C by calcination at 750 °C showed complete regenera-tion for MgCo2O4–Co3O4 samples and its absence in case of an excess of MgO relative to stoi-chiometry. Based on the data obtained, it can be concluded that the processes governing the formation of Co–Mg oxide systems are determined by both Co:Mg ratio and the heat treatment conditions, potentially providing the possibility of fine tuning for specific catalytic processes.

This study aims to quantify greenhouse gas (GHG) emissions from China's sludge treatment industry and explore the potential of novel technologies to mitigate these emissions, promoting sustainable sludge management practices. Using a life cycle assessment approach, the total GHG emissions from sludge treatment in 2017 were estimated at 18.54 Mt CO2-eq, with significant regional variations. Incineration contributed the highest emissions (1,011.53 kg CO2-eq/t dry sludge), followed by landfill (717.51 kg CO2-eq/t) and land application (276.41 kg CO2-eq/t). The uneven distribution of emissions across cities highlights the need for targeted mitigation strategies that consider local sustainability challenges. Principal component analysis revealed that economic factors and treatment scale significantly influence emissions, emphasizing the importance of integrating sustainability goals with economic development. To reduce the carbon footprint of sludge treatment and enhance sustainability, the mitigation potential and costs of various technologies were evaluated, including thermal conversion, anaerobic digestion, hydrothermal processes, and wet oxidation. These technologies offer GHG emission reductions ranging from 0.09 to 0.46 t CO2-eq/t dry solids compared to conventional methods, while also promoting resource recovery and circular economy principles. However, further optimization is necessary to enhance their environmental and economic performance, ensuring long-term sustainability. By implementing these technologies and adopting optimization strategies, China's sludge treatment industry can significantly contribute to achieving the country's carbon neutrality goal and fostering sustainable development.

Most of the mid-high permeability sandstone oilfields in China have entered the ultra-high water cut stage, accompanied with the highly-dispersed residual oil, and the control effect of mi-cro-heterogeneity on the residual oil is increasingly prominent. Understanding the microscopic characteristics of pore structural and its evolution during the long-term waterflooding is critical for enhancing the accuracy and efficiency of oil field exploitation. While the previous insights paid more attention to the geometrical and morphological features of pore structure and ignores the relation of pore structure with the fluid flow capacity. In this study, we propose a microscopic pore structure classification method considering pore size and local permeable capacity, which realizes the physical classification and quantitative evaluation of pore structure characteristics for different permeability rocks. The micro-pore structure is classified into 6 types based on the key evaluation parameters of pore diameter and flow flux area. By taking six mid-high permea-bility sandstone core samples from Daqing oilfield in China, a series of long-term waterflooding experiments are carried out and the interior pore structure was captured using high precision CT scanning technique. The results reveals that high-permeability reservoirs exhibit concentrated pores diameters and finer throats, whereas mid-permeability reservoirs exhibit smaller pores and throats in greater quantity. With the increase of water injection volumes, the permeable ca-pacity and connectivity of the high-connectivity pore space in ultra-high- and high-permeability reservoirs are enhanced, and in mid-permeability reservoirs, the micro-heterogeneity intensifies the increase in low-connectivity small pores. These findings provide new insights for the micro-scopic heterogeneity and a solid theoretical basis for investigating the occurrence of microscopic residual oil and optimising enhanced oil recovery strategies at the late stage of ultra-high water cut.

Infrastructure development is rapidly increasing, driving up demand for concrete, a key construction material. Cement and aggregate are essential constituents, with global cement production reaching 4.1 billion metric tons in 2011 and CO2 emissions hitting 1.7 billion metric tons by 2024, a significant contributor to carbon emissions. To address this, alternative constituents like Rice Husk Ash (RHA) and Animal Bone Powder (ABP) are proposed. With rice husk comprising 20% of rice weight and a substantial cattle population in Bangladesh, RHA and ABP offer promising alternatives. This study examines the benefits and limitations of incorporating RHA and ABP into cement, focusing on concrete strength and permeability. By replacing varying percentages of cement with RHA and ABP simultaneously, experiments evaluate their impact on concrete properties after 28 days of curing. The research aims to identify the optimal combination for sustainable concrete production, reducing environmental impact by curbing waste generation and pollution. Results show that compressive strength increases and permeability decreases with up to 5% replacement of RHA and ABP, highlighting their potential for enhancing concrete performance while mitigating environmental concerns.

Analyses of the three predominant types of sedimentation – clastic, carbonate and black shale – revealed their discontinuity/continuity in different facies environments of the Middle and Late Devonian of the central part of the Volga-Urals petroleum province, namely (1) in depressions, both condensed and non-condensed, (2) on the slopes of depressions and (3) in shallow water environments represented by tectonic arches or localised biohermal uplifts. The regional zonation of conodonts, correlated with the global chronostratigraphic scheme, substantiates the stratigraphic completeness of the general Devonian sequence in this area. In particular, the sedimentation of organic-rich black shales, traditionally considered as source rocks, lasted more than 29 million years, starting from the Late Eifel and ending at the Devonian-Carboniferous boundary. There was only one hiatus in the deposition of both black shales and carbonate sediments, lasting about 2.5 million years at the end of the Frasnian. That interval is dominated by clastic sediments, which are considered to be the most productive reservoirs of the Volga-Ural province. In the time interval from the beginning of the Eifel to the end of the Frasnian (about 17 Ma), (a) clastic sediments show the highest accumulation rates; (b) the most complete sequences occur in depressions; and (c) arches and uplifts show the most significant gaps in the geological record. During Famennian, (a) clastic sedimentation has completely ceased; (b) differences between the slopes of troughs and shallow-water environments have diminished, resulting in stable accumulation of carbonate sediments in both settings; (c) the decrease in sequence thickness (up to 50 m) in depressions suggests reduced accumulation rates of deep-water organic-rich black shales. The results help to understand the complex spatial relationship between different coexisting sedimentation types and focus attention to the incompleteness of the geological record in different environments.

High-precision conical threads are widely used in responsible joints in the drilling of oil and gas wells. Difficult underground drilling conditions due to the occurrence of significant mechanical loads and an aggressive environment in wells require the use of workable materials that are often difficult to machine. The huge need for such connections dictates the use of high-performance cutting tools, which means that high demands are placed on their effective geometric performance. The study describes the theoretical dependence of the profile precision of the tapered drill-string tool-joint threads of all standard sizes on the complex of a cutting tool geometric parameters and cutting tool setting accuracy. The experiments include an assessment of the geometric accuracy of the profile of the obtained NC23 thread connector, depending on the values of the installation angles and the declared tangential displacement of the standard threaded carbide insert.

Maritime data not only identify financial resources that can significantly enhance the efficiency of shipping companies but also play a pivotal role in promoting eco-friendly and sustainable shipping practices. However, active corporate strategies are required to include maritime data essential for the commercial operation of autonomous ships in the form of corporate assets by transparent evaluating the data. The aim of this study is to review previous studies on da-ta-valuation models, identify a valuation model suitable for maritime business, consider the characteristics of maritime data. The analytic hierarchy process (AHP) method is used to derive priorities for valuing maritime data assets, with emphasis placed on the characteristics of mari-time data, followed by the character of the future-oriented maritime-data market and the da-ta-valuation model. The results obtained that the most important factors in selecting a maritime data-valuation model by analyzing the AHP method were identified as the characteristics of the maritime data(M1). The next most important factors analyzed were the features of the mari-time-data market(M2) and the features of the maritime data-valuation model(M3) in order. In addition, the characteristics of maritime data were preferentially considered among the main criteria, and the market approach (A2) was selected as the most optimal valuation model. The potential impact of this implementation could contribute to the establishment of an intelligent technology market by estimating the value of data and developing a platform for maritime data trading, allowing for more efficient data sharing and utilization by maritime autonomous sur-face ship(MASS).

(1) Background: After the discovery and application of Chlamydomonas reinhardtii channelrhodopsins, the optogenetic toolbox has been greatly expanded with engineered and newly discovered natural channelrhodopsins. However, channelrhodopsins of higher Ca2+ conductance or more specific ion permeability are still in demand. (2) Methods: In this study, we mutated the conserved aspartate of the transmembrane helix 4 (TM4) within Chronos (Stigeoclonium helveticum channelrhodopsin = ShChR) and PsChR (Platymonas subcordiformis channelrhodopsin) and compared them with published ChR2 (C. reinhardtii channelrhodopsin-2) aspartate mutants. (3) Results: We found that the ChR2 D156H mutant (XXM) showed enhanced Na+ and Ca2+ conductance, which was not noticed before, while the D156C mutation (XXL) influenced the Na+ and Ca2+ conductance only slightly. Furthermore, the D173H mutant of PsChR showed a much improved photocurrent, compared to wildtype, and even higher Na+ selectivity to H+ than XXM. PsChR D173H also showed a strongly enhanced Ca2+ conductance, more than 2-fold that of the calcium translocating L132C of ChR2 (CatCh). (4) Conclusions: We found that mutating the aspartate of the TM4 to histidine influences the ion selectivity of channelrhodopsins. With the large photocurrent and enhanced Na+ selectivity and Ca2+ conductance, XXM and PsChR D139H are promising powerful optogenetic tools, especially for Ca2+ manipulation.

Among the various types of gas sensors, the chemoresistive gas sensors based on metal oxides are considered the most attractive ones due to their simple operation, low costs and miniaturization. Thin films of V2O5 undoped and doped with TiO2 were studied as nitrogen dioxide, methane and hydrogen sensors. The experimental kinetics of the electrical conductivity changes due to introduction and removal of gas on metal oxide gas sensors were successfully explained in terms of the Langmuir adsorption theory.

Natural gas hydrate, also known as combustible ice and mainly composed of methane, it is identified as the potential clean energy in the 21th century. Due to its large reserves, gas hydrate can ease problems caused by energy resource shortage and has gained attention around the world. In this paper, we focus on the exploration and development of gas hydrate as well as discussing its status and future development trend in China and abroad, then we analyze its opportunities and challenges in China from four aspects: resource, technology, economy and police with five forces model and PEST method. The results show, China has abundance gas hydrate resource; however the backward technologies and inadequate investment has seriously hindered the future development of gas hydrate, so China should establish relevant cooperation framework and intuitional arrangement to attract more investment as well as breaking through technical difficulties to make gas hydrate commercialization as soon as possible.

The article delves into the crucial realm of compressing hydrogen in its gaseous state, a pivotal process for enhancing its viability in both civil and industrial sectors. The study initiates by providing a concise overview and comparison of diverse hydrogen storage methodologies, laying the groundwork with an in-depth analysis of hydrogen's thermophysical properties. It scrutinizes plausible configurations for hydrogen compression, aiming to strike a delicate balance between energy consumption, predominantly derived from the fuel itself, and the requisite number of compression stages. Notably, to render hydrogen storage competitive in terms of volume, pressures of at least 350 bar are deemed essential, albeit at an energy cost amounting to approximately 10% of the fuel's calorific value. Multi-stage compression emerges as a crucial strategy, not solely for energy efficiency, but also to curtail temperature rise, with an upper limit set at 200°C. This nuanced approach is underlined by the exploration of compression levels commonly cited in the literature, particularly 350 bar and 700 bar. Ultimately, the study advocates for a three-stage compression system as a pragmatic compromise, capable of achieving high-pressure solutions while keeping compression work below 10 MJ/kg, a threshold indicative of sustainable energy utilization.

Phased injection of natural gas into internal combustion marine engines is a promising solution for optimizing performance and reducing harmful emissions, particularly unburned methane, a potent greenhouse gas. This innovative practice distinguishes itself from continuous injection because it allows for more precise control of the combustion process with only a slight increase in system complexity. By synchronizing the injection of natural gas with the intake and exhaust valve opening and closing times while also considering the gas path in the manifolds, methane release into the atmosphere is significantly reduced, making a substantial contribution to efforts to address climate change. Moreover, phased injection improves the efficiency of marine engines, resulting in reduced overall fuel consumption, lower fuel costs, and increased ship autonomy. This technology has been tested on a single-cylinder, large-bore, four-stroke research engine designed for marine applications, operating in dual-fuel mode with diesel and natural gas. Performance was compared with that of the conventional continuous feeding method. Evaluation of the effect on equivalent CO2 emissions indicates a potential reduction of up to approximately 20%. This reduction effectively brings greenhouse gas emissions below those of the diesel baseline case, especially when injection control is combined with supercharging control to optimize the air-fuel ratio.

The transition to cleaner energy sources, particularly in hard-to-abate industrial sectors, often requires gradual integration of new technologies. Hydrogen, crucial for decarbonization, is explored as a fuel in blended combustions. Blending or replacing fuels impacts combustion stability and heat transfer rates due to differing densities. An extensive literature review examines blended combustion, focusing on hydrogen-methane mixtures. While industrial burners claim to accommodate up to 20% hydrogen, theoretical support is lacking. A novel thermodynamic analysis methodology is introduced, evaluating methane-hydrogen combustion using the Wobbe index. Findings highlight practical limitations beyond 25% hydrogen volume, necessitating a shift to "totally hydrogen" combustion. Blended combustion can be proposed as a medium-term strategy, acknowledging hydrogen's limited penetration. Higher percentages require burner and infrastructure redesign.

The primary objective of this study was to demonstrate the potential of digital image analysis as a tool to identify microplastic (MP) particles in surface waters and to facilitate their characterisation in terms of 2D and 3D morphology. Digital image analysis preceded by microscopic analysis was used for an exhaustive quantitative and qualitative evaluation of MPs isolated from the Vistula river. Using image processing procedures, 2D and 3D shape descriptors were determined. The Principal Components Analysis (PCA) was used to interpret the relationships between the parameters studied, characterising MP particle geometry, type and colour. This multivariate analysis of the data allowed 3 or 4 main factors to be extracted, explaining approximately 90% of the variation in the data characterising MP morphology. It was found that the first principal component for granules, flakes and films was largely represented by strongly correlated with 2D shape descriptors (area, perimeter, equivalent area diameter) and 3D shape descriptors (CSF, Compactness, Dimensionality). Considering the scraps, PC1 was represented by only five of the above descriptors, and the Compactness variable had the largest contribution to PC2. In addition, for granules, flakes and films, a relationship between 2D shape and the colour of their particles could be observed. For the most numerous MP group identified of multicoloured scraps, no such association was found. The results of our study can be used for further multivariate analysis regarding the presence of microplastic floating on the river surface, with a particular focus on particles of secondary origin. This is of key importance for optimising future efforts in conducting small-scale and multidimensional monitoring of and reducing plastics in the aquatic environment.

Nanostructured carriers have been widely used in pharmaceutical formulations for dermatological treatment. They offer targeted drug delivery, sustained release, improved biostability, and low toxicity, usually presenting advantages over conventional formulations. Due to its large surface area, small size and photothermal properties, graphene oxide (GO) has the potential to be used for such applications. Nanographene oxide (GOn) presented average sizes of 197.6 ± 11.8 nm, and a surface charge of -39.4 ± 1.8 mV, being stable in water for over 6 months. 55.5 % of the mass of GOn dispersion (at a concentration of 1 mg mL-1) permeated the skin after 6 h of exposure. GOn dispersions have been shown to absorb near-infrared radiation, reaching temperatures up to 45.7 °C, within mild photothermal therapy temperature range. Furthermore, GOn in amounts superior to those which could permeate the skin were shown not to affect human skin fibroblasts (HFF-1) morphology or viability, after 24 h of incubation. Due to its large size, no skin permeation was observed for graphite particles in aqueous dispersions stabilized with Pluronic P-123 (Gt-P-123). Altogether, for the first time, GOn potential as a topic administration agent and for delivery of photothermal therapy has been demonstrated.

Evaluation of drug permeability using cell monolayers is an important in vitro assay in the process of drug development, to identify compounds with favourable pharmacokinetics that may proceed to in vivo studies. When allowed to differentiate on permeable filters for at least 21 days, monolayers of Caco-2 cells develop morphological and functional properties similar to those of the intestinal epithelium. Permeability through Caco-2 monolayers is thus particularly relevant to assess drug absorption after oral administration. The major drawback of this assay is its very low throughput, with the cell monolayers being used in a single permeability assay. We have previously proposed a protocol to allow the re-use of the Caco-2 monolayer on additional permeability assays during the stable period and shown that cell monolayer integrity is maintained. In this work we evaluate the effect of re-use on the permeability of several reference compounds that permeate through passive pathways and show that the cell monolayers can be re-used twice in additional permeability assays. Preliminary results were also obtained regarding active transport pathways, and a new methodology is proposed to quantify the contribution from passive and active transport. This is a major step towards the full validation of the re-use methodology proposed, which at least triplicates the throughput of this important in vitro assay.

Appling the controlling relative permittivity and permeability in the equations for the gravitational-magnetic-electric field interaction, a very large variation of the gravitational acceleration of the Earth by electric/magnetic field could be arrived at. This conclusion may be supported by some of the experiments for the gravitational effect of superconductivity.

The activity of the mitochondrial Permeability Transition Pore, mPTP, a highly regulated multi-component mega-channel, is enhanced in aging and in aging-driven degenerative diseases. mPTP activity accelerates aging by releasing large amounts of cell-damaging Reactive Oxygen Species, Ca2+ and NAD+. The various pathways that control the channel activity, directly or indirectly, can therefore either, inhibit, or accelerate aging, retards, or enhance the progression of aging-driven degenerative diseases, and determine lifespan and healthspan. Autophagy, a catabolic process that removes and digests damaged proteins and organelles protects the cell against aging and disease. However, the protective effect of autophagy depends on mTORC2/SKG1 inhibition of mPTP. Autophagy is inhibited in aging cells. Mitophagy, a specialized form of autophagy, which retards aging by removing mitochondrial fragments with activated mPTP, is also inhibited in aging cells, and this inhibition leads to increased mPTP activation, which is a major contributor to neurodegenerative diseases, such as Alzheimer’s and Parkinson’s Diseases. The Increased activity of mPTP in aging turns autophagy/mitophagy into a destructive process leading to cell aging and death. Several drugs and lifestyle modifications that enhance healthspan and lifespan enhance autophagy and inhibit the activation of mPTP. Therefore, elucidating the intricate connections between pathways that activate and inhibit mPTP, in the context of aging and degenerative diseases, could enhance the discovery of new drugs and lifestyle modifications that slow aging and degenerative disease.

In this study, the relationship between air diffusivity and permeability in cementitious materials was investigated. First, we derived an equation to correlate air diffusivity and permeability in a straight circular tube. Then, we reviewed existing studies that measured both air diffusivity and permeability and compared reported data and calculated values to verify the applicability of the derived equation to cementitious materials. Although a correction factor was not used, the two sets of data showed good agreement quantitatively. This indicates that the derived equation can be applied to cementitious materials including concrete, and measured air diffusivity can be converted to permeability of concrete and vice versa using the derived equation.

The effect of H2S with high concentrations on catalytic dry reforming of methane (DRM) process has seldom been focused on previously. Herein, a thermodynamic analysis of the DRM reactions in the presence of H2S with the concentration varying in 0-20 vol% was conducted firstly. Several typical types of catalysts including MgO, NiO/MgO and LaNiO3 in different states were prepared for executing DRM at 800 C, 0.1 MPa in the feed of 20 vol% CO2 and 20 vol% CH4 balanced with N2. The catalytic performance of each catalyst for DRM process under conditions of absence and presence of H2S was compared. A promotion effect of increasing H2S concentration on both the conversions of CO2 and CH4 and the molar yields of CO and H2 was observed on all the catalysts especially the MgO and the pristine NiO/MgO. While a significant decline in catalytic activity of either the reduced NiO/MgO or the reduced LaNiO3 catalyst after adding H2S, moderate reactant conversions still sustained. The results of process analysis and catalyst structure characterization suggest that H2S participation can contribute to the increment in CO2 and CH4 conversion, and active S-adsorbed species may play the key role of catalysis in the reactions involving H2S.

The development effect of water flooding in ultra-low permeability reservoir was poor due to its poor physical property and high shale content, the experimental study of air flooding which help to complement producing energy was carried out. Based on the Accelerating Rate Calorimeter experimental results, the crude oil of N block in L oilfield can produce low-temperature oxidation reaction, which was the basic condition of air flooding. Three groups of experiment natural cylinder core were designed for oil displacement, water flooding and air flooding were used respectively, and the relationship of differential pressure, oil recovery, injection capacity with injection volume was investigated. It has been showed on the result that the recovery efficiency improved sharply than water flooding, the effect of depressurization and augmented injection was obvious, and the air displacement was validation.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

. Protein cysteine S-glycosylation is a relatively rare and less well characterized post-translational modification (PTM). Creating reliable model proteins that carry this modification is challenging. The lack of available model or natural S-glycosylated proteins significantly hampers the development of MS-based methodologies for detecting protein cysteine S-glycosylation in real-world proteomic studies. There is also limited MS-sequencing data describing easier to create synthetic S-glycopeptides. Here, we present the results of an in-depth manual analysis of automatically annotated CID/HCD spectra for model S-glucopeptides. The CID spectra show a long series of y/b-fragment ions with retained S-glucosylation, regardless of the dominant m/z signals corresponding to neutral loss of 1,2-anhydroglucose from the precursor ions. In addition, the spectra show signals manifesting glucosyl transfer from the cysteine position onto Lys, Arg side chains, and a peptide N-terminus. Other spectral evidence indicates that the N-glucosylated initial products of transfer are converted into N-furanosylated (i.e., glycated) structures due to Amadori rearrangement. We discuss the peculiar transfer of the glucose oxocarbenium ion (Glc+) to positively charged guanidinium residue (ArgH+) and propose a mechanism for the gas-phase Amadori rearrangement involving a hydride ion shift.

Hantavirus cardiopulmonary syndrome (HCPS) is characterized by capillary leak, pulmonary edema (PE) and shock that leads to death in up to 40% of patients. Treatment is supportive, including mechanical ventilation (MV) and extracorporeal membrane oxygenation (ECMO). Hemodynamic monitoring is critical to titrate therapy and to decide ECMO support. Transpulmonary thermodilution (TPTD) provides hemodynamic and PE data that has not been systematically used to understand HCPS pathophysiology. We identified 11 HCPS patients monitored with TPTD; 5 on MV, 3 on ECMO. We analyzed 133 measurements to describe the hemodynamic pattern and its association to PE. The main findings were reduced stroke volume, global ejection fraction (GEF) and preload parameters associated to increased extravascular lung water and pulmonary vascular permeability compatible with hypovolemia, myocardial dysfunction and increased permeability PE. Lung water correlated positively with heart rate (HR, r=0.20) and negatively with mean arterial pressure (r=-0.27) and GEF (r=-0.36), suggesting that PE is linked to hemodynamic impairment. Pulmonary vascular permeability correlated positively with HR (r=0.31) and negatively with cardiac index (r=-0.49), end-diastolic volume (r=-0.48) and GEF (r=-0.40), suggesting that capillary leak contributes to hypovolemia and systolic dysfunction. In conclusion, TPTD data suggests that in HCPS patients, increased permeability leads to PE, hypovolemia and circulatory impairment.

Correlations between the air permeability coefficient and various pore structure indicators in cementitious materials were examined to determine the pore structure indicator that best evaluated air permeability using data from previous studies of air permeabilities and pore structures. The determination coefficients of air permeability with total pore volume, critical pore diameter, and ordinary threshold pore diameter were low, although these have often been used as indicators. The median and threshold pore diameters obtained by percolation theory showed high determination coefficients. The equation using the threshold pore diameter better estimated the air permeability coefficient than the Katz–Thompson equation.

To understand the relationship between water permeability and the pore structure of cementitious materials, literature that studied both water permeability and the pore structure are reviewed, and their correlation is studied. Although the majority of this data is for cement paste, mortar, concrete, and cemented soil are also included. Based on this study, it is established the determination coefficient between water permeability and the total pore volume is very low; however, those between water permeability and the critical, threshold, and median pore diameters, respectively, are moderate. On the other hand, the threshold pore diameter, derived based on the percolation theory, exhibits a very high determination coefficient. The calculated water permeability, using the Katz and Thompson equation, agrees with the reported water permeability quantitatively to a certain level, but is overestimated.

Fe-(9, 19, 28, 37)wt.% Cr alloys were corroded at 700 and 800 ^oC for 70 h under 1 atm of N₂, 1 atm of N₂/3.2%H₂O-mixed gas, and 1 atm of N₂/3.1%H₂O/2.42%H₂S-mixed gas. The corrosion rate of Fe-9Cr alloy increased with the addition of H₂O, and furthermore with the addition of H₂S in N₂ gas. Fe-9Cr alloy was always nonprotective. In contrast, Fe-(19, 28, 37) wt.%Cr alloys were protective in N₂ and N₂/H₂O-mixed gas because of formation of the Cr₂O₃ layer. They were, however, nonprotective in N₂/H₂O/H₂S-mixed gas because sulfidation dominated to form the outer FeS layer and the inner Cr₂S₃ layer containing some FeCr₂S₄.

Pipelines extend thousands of kilometers to transport and distribute oil and gas. Given the challenges often faced with corrosion, fatigue, and other issues on steel pipes, the demand for glass fiber reinforced plastics (GFRP) pipes is increasing in the oil and gas gathering and transmission systems. However, the medium transported through these pipelines contains multiple acid gases such as CO2 and H2S, as well as ions including Cl-、Ca2+、Mg2+、SO42-、CO32- and HCO3-. These substances can cause a series of problems, such as aging, debonding, delamination, and fracture. In this study, a series of aging damage experiments were conducted on V-shaped GFRP pipes with depths of 2mm and 5mm. The aging and failure of GFRP were studied under the combined effects of external force and acidic solution using acoustic emission (AE) techniques. It was found that the acidic aging solution promoted matrix damage, fiber/matrix desorption, and delamination damage in GFRP pipes over a short period. However, the overall aging effect was relatively weak. Based on the experimental data, the SSA-LSSVM algorithm was proposed and applied to the damage pattern recognition of GFRP. An average recognition rate of up to 90% was achieved, indicating that this method is highly suitable for analyzing AE signals related to GFRP damage.

Enhancing the management and monitoring of oil and gas processes demands developing precise predictive analytics techniques. Over the past two years, oil and its prediction have advanced significantly using conventional and modern Machine Learning techniques. Several review articles detail the developments in predictive maintenance and technical and non-technical aspects of influencing the uptake of big data. The absence of references for machine learning techniques impacts the effective optimization of predictive analytics in the oil and gas sector. This review paper offers readers thorough information on the latest machine learning methods utilized in this industry's predictive analytical modelling. The review covers forms of Machine Learning techniques used in predictive analytic modelling from 2021 to 2023 (91 articles). It provides an overview of the details of the papers that were reviewed, comprising of the model’s categories, the data's temporality, field, and name, the dataset's type, predictive analytics (classification or clustering or prediction), the models' input and output parameters, performance metrics, optimal model, and benefits and its drawbacks. Additionally, suggestions for future research directions are provided to raise the potential of the associated knowledge and increase the accuracy of oil and gas predictive analytics models.

The poly lactic acid (PLA) is one of the most used bio-derived thermoplastic polymers in 3D and 4D printing applications. The determination of PLA surface properties is of capital importance in 3D/4D printing technology. (1) Background: The surface thermodynamic properties of PLA polymer were determined by using the inverse gas chromatography (IGC) technique at infinite dilution. The determination of the retention volume of polar and non-polar molecules adsorbed on the PLA particles filling the column allowed us to obtain the dispersive, polar, and Lewis’s acid-base surface properties at different temperatures from 40 °C to 100 °C. (2) Methods: the applied surface method was based on our recent model that used the London dispersion equation and the new chromatographic parameter function of the deformation polarizability and the harmonic mean of the ionization energies of the PLA polymer and organic molecules. (3) Results: The application of this new method led to the determination of the dispersive and polar free surface energy of adsorption of molecules on the polymeric material, as well as the glass transition and the Lewis acid-base constants. (4) Conclusions: four interval temperatures were distinguished showing four zones of the variations of the surface properties of PLA as a function of the temperature before and after the glass transition.

Agriculture (crop production, land use, and livestock) is the second most important greenhouse gas (GHG) emitting sector after the energy sector. Agriculture is also recognized as the source and sink of GHGs. Evidence demonstrates that the application of high amounts of nitrogen-rich fertilizers enhances methane (CH4) and nitrous oxide (N2O) emissions, which are potent GHGs with a high global warming potential (GWP). Considering its global contribution to the climate crisis, reducing GHG emissions in agriculture would considerably lower its share of the global GHG emission records, which may lead to enormous benefits for the environment and food production systems. Several diverging and controversial views questioning the actual role of plants in the current global GHG budget continue to nourish the debate globally. We must acknowledge that considering the beneficial roles of major GHGs to plants at a certain level of accumulation, implementing GHG mitigation measures from agriculture is indeed a complex task. This review seeks to provide key approaches for GHG mitigation in the literature (environmentally friendly crop cultivation and residue management practices, improvement of plants nutrients/fertilizer use efficiency, exploring the genetic diversity for low GHG emission, soil methane-producing bacteria, integrated soil fertility management, improved livestock feeding efficiency, and production, etc.). This work gathers key approaches from 275 peer-reviewed publications, including experimental research papers, review articles, and books, discussing greenhouse gas emissions mechanisms and mitigation to unravel effective strategies for GHG mitigation, proven to be effective or carry the potential to mitigate GHG generation from agriculture. This review also discusses in depth the significance and the dynamics of strategies regarded as game changers with a high potential to enhance, in a sustainable manner, the resilience of agricultural systems. Agricultural GHG mitigation approaches discussed in this work can serve as game changers in global efforts to reducing GHG emissions and alleviating the impact of climate change through sustainable agriculture and informed-decision making.

The increasing regulatory pressure to monitor and reduce GHG emissions and air pollutants requires cost-effective methods for their surveillance. The most common technique used for scientific investigations on gas concentration monitoring in barns are accurate but expensive and with a complex maintenance. This research study analysed the potential use of a low-cost portable measurement devices for the measurement of ammonia (NH3) and carbon dioxide (CO2) concentrations in an open dairy barn. A comparison between gas concentrations acquired at different heights from the floor by using portable devices and those acquired by a photoacoustic infrared multigas spectroscope (i.e., reference measurement) in the same sampling locations was carried out to determine the precision of the low-cost portable devices. The performance of low-cost portable devices was statistically analysed by the application of the one-way analysis of variance, correlation analysis and regression analysis. The results showed a significant difference between gas concentration values at various heights from the floor for both NH3 and CO2. The correlations between concentrations acquired by the low-cost portable device and the INNOVA were statistically significant (r=0.83; P<0.001) for gas concentrations monitored at 0.4 m from the floor. Compared with the reference measurement device, the low-cost devices were effective in the monitoring of NH3 concentrations at 0.40 m from the floor though it underestimated them in the barn at increasing of the height from the floor, whereas the device was not adequate for CO2 concentrations. In detail, the relative measurement error of the low-cost devices compared to INNOVA was reduced close to the floor during NH3 concentration measurements. Within these limitations, this device could be useful for monitoring NH3 concentration in the barn and to assess variation in NH3 concentrations mainly related to the animal occupied zone. Further efforts are needed in this field of research to identify low-cost device that could simplify emission estimation from open dairy barns.

It is known that ammonium has a higher permeability through anion-exchange and bipolar membranes compared to K+ cation that has the same mobility in water. However, the mechanism of this high permeability is not clear enough. We develop a mathematical model based of the Nernst-Planck and Poisson equations for diffusion of ammonium chloride through an anion-exchange membrane; proton exchange reactions between ammonium, water and ammonia are taken into account. It is assumed that ammonium, chloride and OH− ions can only pass through membrane hydrophilic pores, while ammonia can also dissolve in membrane matrix fragments not containing water and diffuse through these fragments. It is found that due to the Donnan exclusion of H+ ions as coions, the pH in the membrane internal solution increases when approaching the membrane side facing distilled water. Consequently, there is a change in the principal nitrogen-atom carrier in the membrane: in the part close to the side facing the feed NH4Cl solution (pH<8.8), it is the NH4+ cation, and in the part close to distilled water, NH3 molecules. The concentration of NH4+ reaches almost zero at a point close to the middle of the membrane cross-section, which approximately halves the effective thickness of the diffusion layer for the transport of this ion. When NH3 takes over the nitrogen transport, it only needs to pass through the other half of the membrane. Leaving the membrane, it captures an H+ ion from water, and the released OH− goes towards the membrane side facing the feed solution to meet the NH4+ ions. The comparison of the simulation with experiment shows a satisfactory agreement.

The deterioration of soil-cement in corrosive environment leads to the reduction of strength and the increase of permeability. Effective methods of determining deteriorated layer permeability coefficient of soil-cement are currently lacking. A laboratory test method for permeability coefficient of deteriorated layer was proposed using the modified permeability coefficient testing apparatus. According to the proposed method, the permeability coefficient of deteriorated layer can be obtained after testing the permeability coefficient of the soil-cement specimen in curing room and the equivalent permeability coefficient and deterioration depth of the soil-cement specimen in corrosion environment. Taking the marine dredger fill of Jiaozhou Bay for example, the deteriorated layer permeability coefficients of soil-cements with different cement contents were tested. It turned out that the permeability of deteriorated layer increases with the increase of age. At the beginning of curing age, larger cement content leads to smaller permeability coefficient of the deteriorated layer of soil-cement. As the curing age increases, the deteriorated layer permeability coefficient of the soil-cement with larger cement content becomes larger. The evolution of the permeability coefficient of deteriorated layer with age can be formulated as the Logistic function. This study provides a support for anti-permeability designs of soil-cement structures in corrosive environment.

This work presents the results regarding the synthesis of tungsten nanoparticles (W NPs) by magnetron sputtering combined with gas aggregation (MSGA) when H2 mixed with Ar is used as working gas, the amount of H2 being increased up to 82%. The results show that up to 40% H2 in discharge the synthesis rate increases over 60 times, rapidly decreasing for over 50% H2 in discharge. The W dust is still produced in H2 dominated discharge (82%), the deposition rate being small but not negligible (20 mg/hour). The obtained WNPs are isolated, with the diameter decreasing from 50 nm to 15 nm when the amount of H2 in discharge is smaller than 41%. Over this value, the particles tend to agglomerate, forming structures similar to film-like deposits. Also, the diameter of the deposited spots on substrates is dependent on the H2 content in discharge. This allows the efficient coating of substrates with dimensions up to 26 mm by translating them in front of the MSGA cluster source exit aperture. Supplementary, for 41% H2 in discharge, the influence of synthetic air leaks (0-5%) in discharge was investigated. The deposition rate decreases rapidly (ceasing for around 4% air in discharge) and the obtained nanoparticles tend to agglomerate (at 2% air content, the dust deposit has the aspect of a near continuous film). Chemical composition investigations show a pronounced tendency of oxidation, nitridation and oxynitride formation in the presence of air leaks.

The surface characterization of indium tin oxide (ITO) films was processed by oxygen (O2) plasma gas using a magnetron sputtering method of varying O2-plasma gas from 20 sccm to 100 sccm for potentially fostering in electronic devices applications on dye-sensitize solar cells (DSSC) in this work. In order to gain an outstanding performance rate with high-quality thin films, the affect of correlation between the electrical, optical, and morphology properties was significantly investigated. Clearly, the content of investigation exhibited that the films properties was changed by variation of the gas composition. These changes have contemporary relevance to the sputtering gas during the deposition process. To conclude, the greatest electrical properties was displayed by O2 -plasma gas flow rate of 20 sccm, which showed the lowest resistivity. In addition to this, the final products were practically fabricated to active layers for dye-sensitize solar cells (DSSC) applications. The highest efficiency of DSSC device was indicated of approximately 0.35% which was located by 40 sccm of the O2-plasma gas. Consequently, the study could be a possibility way of preparing ITO thin films with improved special properties of substantial applications for solar cells devices in the near future.

Cell monolayers, including endothelial and epithelial cells, play crucial roles in regulating the transport of biomolecules to underlying tissues and structures via intercellular junctions. Moreover, the monolayers form a semipermeable barrier across which leukocyte transmigration is tightly regulated. The inflammatory cytokines can disrupt the epithelial and endothelial permeability, thus the reduced barrier integrity is a hallmark of epithelial and endothelial dysfunction related with numerous pathological conditions, including cancer-related inflammation. Therefore, the assessment of barrier function is critical in in vitro models of barrier-forming tissues. This review summarizes the commercially available in vitro systems used to measure the permeability of cellular monolayers. The presented techniques are separated in two large groups: macromolecular tracer flux assays, and electrical impedance measurement-based permeability assays. The presented techniques are briefly described and compared.

This case study focuses on exploring the potential of biogas as a direct substitute for conventional fossil fuels in industrial applications. Instead of being limited to its common uses as a vehicle fuel or for power generation, this research aims to investigate how biogas can be integrated into industrial processes as an advanced and sustainable energy solution. By conducting a detailed analysis of the financial implications associated with the utilization of landfill gas and gas derived from biomass, a comprehensive understanding of their practical applications in the industrial sector can be obtained. This research goes beyond a superficial examination and delves into the intricate aspects of incorporating biogas as a viable alternative fuel source. When we say that utilizing biogas is technically feasible, it means that the necessary infrastructure and technologies are available to support its integration into industrial processes. This implies that there are existing methods and systems in place that can efficiently harness and utilize biogas for various industrial applications. These technologies ensure a seamless transition from conventional fossil fuels to renewable energy sources, leading to a more sustainable and environmentally friendly industrial landscape. Moreover, the statement that utilizing biogas is economically feasible emphasizes that the financial viability of employing biogas in industrial processes is advantageous. This research explores the potential cost savings and benefits associated with substituting conventional fuels with biogas. By carefully examining the economic aspects, such as initial investments, operational costs, and potential revenue streams, a comprehensive understanding of the financial impact of adopting biogas solutions in the industrial sector can be gained. By expanding and broadening the understanding of the technical and economic feasibility of biogas integration, this research aims to provide valuable insights into the potential of advanced biogas solutions for industrial applications. Indeed, to make biogas a viable and sustainable option as a raw material, it is necessary to establish farming subsidies and financial support specifically tailored for biogas production, similar to the existing support provided for food production. These subsidies and financial incentives play a crucial role in promoting and encouraging the growth of the biogas industry. By establishing such support systems, farmers and other stakeholders in the agricultural sector can be incentivized to participate in the production of biogas. This can involve the utilization of agricultural waste, organic residues, or dedicated energy crops for biogas generation. The financial assistance can help offset the initial investment costs, provide incentives for production, and ensure the economic viability of biogas projects. Moreover, when considering large-scale landfills or situations where industrial demands for energy are relatively low, landfill gas becomes a viable and practical option. Landfill gas, which is generated by the decomposition of organic waste in landfills, can be harnessed and utilized for various industrial purposes. This not only helps in managing waste but also provides a valuable source of renewable energy. In summary, while farming subsidies and financial support are crucial for promoting biogas production, landfill gas remains a viable option for large landfills or situations with minor industrial demands. The combination of these two approaches offers a comprehensive outlook on utilizing biogas as a renewable energy source for industrial applications.

This study presents a methodology to fabricate Ti6Al4V cylindrical compacts with a highly porous core and dense shell with the purpose to mimic the bone microstructure. Compacts with different core diameters were obtained by conventionally press and sintering. Large pores were created with the aid of pore formers. Sintering kinetics was determined by dilatometry, whereas characterization was performed by X-ray computed tomography. Also, permeability was evaluated on the 3D microstructure and the mechanical strength was evaluated by compression tests. Results indicated that sintering is constraint by the different densification rates of the porous and dense layers. Nonetheless, defectless compacts were obtained due to neck bonding between Ti6Al4V particles. Large pores were located in the designed core with similar pore size distribution. Permeability increased following a power law as a function of the pore volume fraction. Stiffness of bilayer components was driven by the porous core, meanwhile, the strength resulted from the combination of both layers. Bilayer materials obtained showed a permeability and mechanical properties, as well as admissible strain (σy /E) similar to those of human bones.

Thin Pd-40%Cu films were obtained by the classical melting and rolling method, magnetron sputtering and modified with nanostructured functional coatings to intensify the process of hydrogen transport. The films were modified by electrodeposition according to the classical method of obtaining palladium black and "Pd-Au nanoflowers" with spherical and pentagonal particles, respectively. The experiment results demonstrated the highest catalytic activity (89.47 mA cm–2), good resistance to CO poisoning and long-term stability of Pd-40%Cu films with a pentagonal structured coating. The investigation of the developed membranes in the hydrogen transport processes in the temperature range of 25-300°C also demonstrated high and stable fluxes up to 475.28 mmol s–1 m–2 (deposited membranes) and 59.41 mmol s–1 m–2 (dense-metal membranes), which turned out to be up to 1.5 higher compared to membrane materials with classic niello. For all-metal modified membranes, the increase in flux was up to 7 times, compared with a smooth membrane made of pure palladium, and for deposited films, this difference was several tens of times. The membrane materials selectivity was also high up to 4419. The developed strategy for modifying membrane materials with functional coatings of a fundamentally new complex geometry can shed new light on the development and fabrication of durable and highly selective palladium-based membranes for gas steam reformers.

The lung epithelium regulates gas exchange and is the first line of defense against airborne toxicants and microbial infections. Disruption of the integrity of lung epithelium results in altered permeability and severely impacts normal lung functions. To develop biomarkers of potential harm (BoPH) for assessing adverse health effects of cigarette smoking, we have evaluated lung barrier function. In a single-center, ambulatory, clinical study we measured lung permeability, as the half-life (T1/2) of inhaled 99mTC-DTPA, in 17 subjects consisting of 6 Smokers (SMK), 5 Moist Snuff Consumers (MSC), and 6 Non-Tobacco Consumers (NTC) at three weekly test visits. Smokers, relative to MSC and NTC, exhibited significantly faster clearance of the inhaled probe (shorter T1/2), indicating increased lung permeability. NTC and MSC had comparable clearance times of the inhaled probe (longer T1/2). Least squares regression modeling showed that the variability of the test was minimal and was not significant. Prediction profiling showed that the repeatability of the lung permeability test was robust and was able to differentiate the tobacco product use groups in this study. Thus, altered lung barrier function may serve as a BoPH for assessing the effects of tobacco use.

Doxorubicin (Dox) is a commonly used chemotherapeutic that can adversely affect skeletal muscle, including causing muscle atrophy. Dox is known to induce an event known as mitochondrial permeability transition (MPT) in cardiac muscle and this plays an important role in Dox-mediated cardiac toxicity. Further to this, recent evidence identifies MPT as a mechanism of atrophy in skeletal muscle, suggesting that MPT may underlie some of the Dox-related toxicity in skeletal muscle. To test this hypothesis, we used cultured human primary myotubes, C2C12 myotubes, and single adult mouse flexor digitorum brevis (FDB) muscle fibers in experiments involving Dox treatment with or without inhibitors of MPT. Dox treatment of myotubes caused myonuclear translocation of the mitochondrial protein apoptosis inducing factor (AIF) and increased mitochondrial reactive oxygen species (mROS), consistent with the known consequences of MPT. Furthermore, Dox caused atrophy in C2C12 myotubes grown on patterned plates, human primary myotubes, and single muscle fibers from adult mice. Notably, Dox-induced atrophy could be prevented by a wide variety of agents that inhibit MPT, as well as by inhibiting mROS or Caspase 3. In conclusion, our results indicate that MPT plays an important role in driving Dox-mediated skeletal muscle atrophy.

Abstract: The Saccharomyces cerevisiae mitochondrial unspecific pore (ScMUC) is an uncoupling unspecific pore that shares some similarities with the mammalian permeability transition pore (mPTP). When open, both channels deplete ion and proton gradients across the inner mitochon-drial membrane. However, the role of mPTP is to reversibly open to protect cells against stress. If mPTP remains stuck in the open position the cell dies. In contrast, ScMUC is probably dedicated to deplete oxygen from the medium in order to kill competing organisms. Such O2 depletion would be better achieved if oxidative phosphorylation is at least mildly uncoupled. Still, when oxida-tive phosphorylation is needed ScMUC should be able to close. To test this, the reversible opening and closing of ScMUC in the presence of different effectors was tested in isolated mitochondria from S. cerevisiae. Evaluations were conducted at different incubation times, monitoring the rate of O2 consumption, mitochondrial swelling and the transmembrane potential. It was observed that ScMUC did remain reversibly open for minutes. A low energy charge (ATP/ADP) closed the chan-nel. In addition, high Ca2+ promoted closing and it was a highly powerful effector.

In-situ injection of steam for heating of the subsurface is an efficient method for the recovery of oil and gas from oil shale where permeability typically evolves with temperature. We reported measurements on Jimusar oil shales(Xinjiang, China) at different temperatures to 600℃ and under recreated in situ triaxial stresses to obtain permeability evolution with temperature and stress. Permeability of tight oil shales evolves with temperature to a threshold temperature and peak temperature. The threshold temperature was subjected to triaxial stresses. For Jimusar oil shale, the threshold temperature ranges from 200℃ to 250℃ at ground stress of buried depth of 500m and from 350℃ to 400℃ at buried depth of 1000m. The peak temperature was almost not subjected to triaxial stress and the range is from 450℃ to 500℃ for all Jimusar samples. Pyrolysis plays an important role in permeability evolution and fundamentally changes permeability tendency and magnitude. At high temperature permeability exhibits a little reduction due to stress effect but still remains a high level due to pyrolysis. The above results show that oil shale mass can change from tight porous media into highly permeable media and oil & gas can easily flow through oil shale stratum.

The oil and gas industry in Nigeria, a vital contributor to the nation's economy, has long been associated with significant environmental challenges. Pollution, habitat destruction, and greenhouse gas emissions have raised global concerns about sustainability and corporate responsibility. This empirical study explores the relationship between environmental accounting practices and the financial performance of listed oil and gas companies in Nigeria. We investigated eight oil and gas companies that are publicly traded on the Nigerian Stock Exchange Market (NGX) as of January 17, 2022, from 2011 to 2022. The study employs Driscoll-Kraay standard errors and reveals that environmental accounting had significant effects on returns on assets, earnings per share, and liquidity ratio. The study revealed that the implementation of environmental accounting practices had diverse effects on the performance of oil and gas companies in Nigeria. The findings encourage policymakers and stakeholders in the sector to utilise the insights and design more effective regulations and incentives that promote environmental corporate responsibility. Also, valuable insights into the potential benefits and challenges associated with adopting environmental accounting practices, and influencing the decision-making processes of corporate stakeholders were provided to ensure sustainability in terms of improved financial performance of the oil and gas sector in Nigeria.

Governments worldwide are actively committed to achieving their carbon emission reduction targets, and one avenue under exploration is harnessing the potential of hydrogen. Blending hydrogen with natural gas is emerging as a promising strategy to reduce carbon emissions, as it burns cleanly without emitting carbon dioxide. This blending could significantly contribute to emissions reduction in both residential and commercial settings. However, a critical challenge associated with this approach is the potential for Hydrogen Embrittlement (HE), a phenomenon wherein the mechanical properties of pipe steels degrade due to the infiltration of hydrogen atoms into the metal lattice structure. This can result in sudden and sever failures when the steel is subjected to mechanical stress. To effectively implement hydrogen-natural gas blending, it is imperative to gain a comprehensive understanding of how hydrogen affects the integrity of pipe steel. This necessitates the development of robust experimental methodologies capable of monitoring the presence and impact of hydrogen within the microstructures of steel. Key techniques employed for this assessment include microscopic observation, hydrogen permeation tests, and tensile and fatigue testing. In this study, samples from two distinct types of pipeline steels used in the natural gas distribution network underwent rigorous examination. To induce hydrogen absorption, an electrochemical charging process is employed in a solution rich in H+ ions. This charging process, accomplished by a potentiostat applying a constant current, prompts the hydrogen evolution reaction at the steel specimen, acting as the cathode of the charging cell. Immediate tensile and fatigue testing following the charging process enables the evaluation of mechanical properties in comparison to non-charged samples. Different charging current densities are employed to simulate various hydrogen blend scenarios. The findings from this research indicate that charged samples exhibit a discernible decline in fatigue and tensile properties. This deterioration is attributed to embrittlement and reduced ductility stemming from the infiltration of hydrogen into the steel matrix. The extent of degradation in fatigue properties is correlated not only to the hydrogen content but also to the hydrogen permeability and diffusion rate influenced by steel’s microstructural features, with higher charging current densities indicating a more significant presence of hydrogen in the natural gas pipeline blend.

Permeability is a fundamental property of porous media, especially when studying resin transfer within a dense fibrous medium to manufacture composite materials. When the measurement of permeability tensor of composite reinforcements is difficult and time consuming, especially in thick, heterogeneous fibrous structures, a numerical approach based on the calculation of the tensor components on a 3D image of the material can be very advantageous. A new finite element based method proposed in this study allows solving very high-dimensional flow problems while limiting the biases associated with boundary conditions and the small size of the numerical samples addressed. The method is validated against academic test cases and against the results of a recent permeability benchmark exercise. The results emphasize that for heterogeneous and anisotropic microstructures, it is important to perform calculations on large samples using boundary conditions that do not suppress the transverse flows that occur when flow is forced out of the principal directions. Since these are not necessarily known in complex media, the permeability determination method must not introduce bias by generating non-physical flows.

Various empirical models are available to evaluate the temperature effects on relative permeability of the different rock and fluid systems. However, the implementation of limited experimental data points may hinder the applicability of such models to other systems. This study aims to develop new predictive models for k_ro estimation based on multilayer perceptron artificial neural network (MLP-ANN), adaptive neuro-fuzzy inference system (ANFIS), and least squares support vector machine (LSSVM) approaches. A database comprising of 626 data points applied to the model development. The independent variables are temperature, oil viscosity, water viscosity, water saturation ( ), and the absolute permeability. Each variable covers a wide range of variations which increases models’ potential to be applied in various systems with different characteristics. The doubtful experimental data points excluded using a leverage value approach and a sensitivity analysis carried out to determine the quantitative impact of every individual independent variable on the k_ro. Statistical error analyses demonstrated the coefficient of determination (R²) values of 0.985, 0.975, and 0.999 for MLP-ANN, ANFIS, and LSSVM, respectively. The comparative study indicated that the LSSVM had the best performance regarding both graphical and statistical error analyses among the newly proposed models and previously reported models in the literature.

With the popularization of natural gas and the requirements for environmental protection, the development and utilization of natural gas is particularly important. The status of natural gas in China's oil and gas exploration and development is constantly improving, and the country is paying more and more attention to the exploitation and utilization of natural gas. The Upper Paleozoic tight sandstone in the Ordos Basin is characterized by low porosity, low permeability and large area of concealed gas reservoirs. By injecting CO2 into the formation, the recovery of natural gas can be improved, and at the same time, the stable storage of CO2 can be achieved to achieve a win-win situation of CO2 emission reduction and utilization. Injecting greenhouse gas CO2 into gas reservoirs for storage and improving recovery has also become a hot research issue. In order to improve the recovery efficiency of tight sandstone gas reservoir, this paper takes the complex tight sandstone of Upper Paleozoic in Ordos Basin as the research object, through indoor physical simulation experiments, carried out the influence of displacement rate, fracture dip angle, core permeability, core dryness and wetness on CO2 gas displacement efficiency and storage efficiency, and analyzed the influence of different factors on CO2 gas displacement efficiency and storage efficiency to improve the recovery and storage efficiency. The research results show that under different conditions, when the CO2 injection pore volume is less than 1PV, the relationship between the CH4 recovery rate and the CO2 injection pore volume is linear, and the tilt angle is 45 °. When the CO2 injection pore volume exceeds 1PV, the CH4 recovery rate increases slightly with the increase of displacement speed, the recovery rate of CO2 displacement CH4 is between 87% - 97%, and the CO2 breakthrough time is 0.7PV-0.9PV. In low-permeability and low-speed displacement cores, the diffusion of CO2 molecules is more significant. The lower the displacement speed is, the earlier the breakthrough time of CO2 is, and the final recovery of CH4 slightly decreases. Gravity has a great impact on CO2 storage and enhanced recovery. The breakthrough of high injection and low recovery of CO2 is earlier, and the recovery of CH4 is about 3.3% lower than that of low injection and high recovery. The bound water makes the displacement phase CO2 partially dissolved in the formation water, and the CO2 breakthrough lags about 0.1PV. Ultimately, CH4 recovery factor and CO2 storage rate are higher than those of dry core displacement. The research results provide theoretical data support for CO2 injection to improve recovery and storage efficiency in complex tight sandstone gas reservoirs.

Recent studies have reported shallow and deep seep areas offshore Mocha island. Gas hydrate occurrences along the Chilean margin could explain seeps presence. Gas phases (gas hydrate and free gas) and geothermal gradients were estimated analysing two seismic sections. Close to Mocha island (up to 20 km) were detected high (up to 1900 m/s) and low (1260 m/s) velocities associated with high gas hydrate (up to 20 % of total volume) and free gas (up to 1.1% of total volume) concentrations respectively. These values are in agreement with a variable and high geothermal gradient (65 to 110 °C/km) related to high supply deep fluids canalised by faults and fractures. Faraway from Mocha island (more than 60 km), free gas concentrations decrease to 0.3 % of total volume and low geothermal gradient (from 35 to 60 °C/km) are associated with low fluids supply. Finally, we propose gas hydrate dissociation processes as the main supply source for seeps in the vicinity of Mocha island. These processes can be triggered by ancient sliding reported in literature.

In order to achieve global climate goals, it is necessary to estimate greenhouse gases (GHG) fluxes from ecosystems. To obtain a comprehensive assessment of CO2, СН4, N2O natural fluxes for the Russian Federation we used the "bottom-up" method according to [1]. We updated estimates for forest ecosystems based on State Forest Inventory data and satellite monitoring of forest disturbances. For grassland ecosystems, it was based on the correct distribution of areas between steppe and non-steppe zones. The estimated net uptake of natural ecosystems of Russia was 1.1 ± 1.8 billion tons of CO2-eq./year. The study shows that if only CO2 is taken into account, the net absorption of terrestrial ecosystems in Russia corresponds to more than -2.5 billion tons of CO2 (35% of forests’ contribution). However, given the emissions of non-CO2 GHGs, total net absorption in Russia’s natural ecosystems is reduced to about -1 billion tons of CO2-eq (with the forests’ contribution increasing to 80%). With regard to anthropogenic fluxes, the overall balance of GHGs in Russia corresponds to net-emissions of 1 billion tons of CO2-eq/year into the atmosphere. To improve reporting under the Paris Agreement, countries should aim to include only anthropogenic ("manageable") GHG fluxes on managed land.

Uncertainties in initial water saturation and early water breakthroughs of un-known sources and paths, which occurred in the low resistivity Lower Haushi sand-stone (LHS) reservoir at the beginning of oil production, imply that the bypassed oil can yet remain in the reservoir. In addition, the upper part of LHS is a tight oil reser-voir, which can still contain a significant amount of unrecovered oil. This opens the opportunity to produce the remaining oil instead of abandoning this reservoir. Low resistivity can exaggerate water saturation, leading to misinterpretation and premature water flooding due to inadequate oil-water contrast. Our analysis revealed a correlation between low resistivity and robust porous network connectivity, along-side elevated formation water salinity in highly porous layers. In regions of high po-rosity, sufficient oil-water contrast facilitates precise water saturation determination, affirming oil presence in all wells. However, within tight oil zones, near-complete wa-ter saturation contradicts actual oil presence. Factors contributing to saturation un-certainty and water breakthroughs were reassessed. Utilizing a 1:1 verti-cal-to-horizontal permeability ratio derived from core data enhanced simulation alignment with water production rates. Investigation into the impact of relative per-meabilities on water production was conducted. Water saturation maps were gener-ated to pinpoint remaining oil reserves. Depletion around wells is evident in lower po-rous regions, while oil persists across the entire tight reservoir, notably in two unex-plored sections.

This paper investigates the influence of different vegetation on the permeability of the shallow soil layers of slopes under rainfall infiltration. Firstly, four large slopes are filled in the outdoor natural environment, and the overburdens of the four slopes are Magnolia multiflora, Cynodon dactylon, Magnolia multiflora mixed with Cynodon dactylon, and no vegetation. Secondly, the four slopes are cultivated in the outdoor natural environment for one year. After the vegetation overburdens are matured, the field artificial rainfall test is carried out through the self-developed artificial rainfall device to monitor the water migration law inside the four slopes in real time. Finally, the unsaturated permeability coefficients of the shallow soil layers of slopes are calculated. The results show that the infiltration rate of rainwater in each overburden slope from fast to slow is Magnolia multiflora overburden slope, no vegetation slope, Cynodon dactylon overburden slope, Magnolia multiflora mixed with Cynodon dactylon overburden slope. In the early stage of rainfall, Magnolia multiflora increases the permeability coefficient of the shallow soil layer of the slope, thus weakening the anti-seepage ability of the slope, but the influence of Magnolia multiflora is not obvious in the later stage. Cynodon dactylon and Magnolia multiflora mixed with Cynodon dactylon can significantly reduce the permeability coefficient of the shallow soil layers of the slopes, thereby increasing the anti-seepage ability of the slopes, and the mixed planting of Magnolia multiflora and Cynodon dactylon can minimize the permeability coefficient of the shallow soil of the slope, resulting in the best anti-seepage effect.

There is a growing need for novel in vitro corneal models to replace animal-based ex vivo test in drug permeability studies. In this study we demonstrate a corneal mimetic that models the stromal and epithelial compartments of human cornea. Human corneal epithelial cells (HCE-T) were grown on top of a self-supporting porcine collagen-based hydrogel. Cross sections of the multilayers were characterized by histological staining and immunocytochemistry of zonula occludens-1 protein (ZO-1) and occludin. Furthermore, water content and elastic properties of the synthetized collagen type I-based hydrogels were measured. The apparent permeability coefficient (Papp) values of a representative set of ophthalmic drugs were measured and correlated to rabbit cornea Papp values found in the literature. Multilayered structure of HCE-T cells and expression of ZO-1 and occludin in full thickness of multilayer were observed. The hydrogel-based corneal model exhibited excellent correlation to rabbit corneal permeability (r=0.96), whereas insert-grown HCE-T multilayer was more permeable and the correlation to the rabbit corneal permeability was lower (r=0.89). The hydrogel-based human corneal model predicts the rabbit corneal permeability more reliably in comparison to HCE-T cells grown in inserts. This in vitro human corneal model can be successfully employed for drug permeability tests whilst avoiding ethical issues and reducing costs.

The surface thermodynamic properties of polymers and copolymers modified by supramolecular structures are very used in several industrial processes, such as selective adsorption, paints, coatings, colloids, and adhesion applications. Background: Inverse gas chromatography at infinite dilution was proved to be the best technique to determine the surface properties of solid surfaces by studying the adsorption of some model polar and non-polar organic molecules adsorbed on solid surfaces by varying the temperature. Methods: The retention volume of adsorbed solvents is a precious parameter to obtain the London dispersive and polar free energies and the London dispersive surface energy of styrene–divinylbenzene copolymer modified by supramolecular structure of melamine using the Hamieh thermal model and our new methodology consisting in the separation of the two polar and dispersive free energy of interaction. This led to the determination of the polar acid and base surface energy, and the Lewis’s acid-base constants of the various solid materials. Results: all surface energetic properties of styrene–divinylbenzene copolymer modified by melamine at different percentages were determined as a function of temperature, following our new methodology. Conclusions: It was observed that the styrene–divinylbenzene copolymer exhibited the highest London dispersive surface energy which decreased when the melamine percentage increased. All materials presented higher Lewis’s basicity and this Lewis’s basicity increased with the percentage of melamine.

The safe and efficient mining of coal seams with low porosity, low permeability and high inhomogeneity under complex geological conditions is a major challenge, among which the permeability of coal seams is crucial for coal mine gas extraction. The development of coal seam permeability enhancement technology can help coal mines to produce safely and efficiently, and the extracted coal bed methane can be utilized as a green energy. In order to study the effect of freezing and thawing on the evolution of mechanical and permeability properties of coal, triaxial permeability tests were carried out on low-permeability coal under two kinds of surrounding pressures. At the same time, dry, saturated and freeze-thaw coal were set up for comparison, and the effects of water and freeze-thaw were separated from each other. The triaxial mechanics and percolation laws of dry, saturated and freeze-thaw coal rocks were obtained, and the mechanism of the influence of freeze-thaw on the permeability evolution law of coal was revealed. The research results can provide theoretical guidance for the gas extraction technology of low permeability coal seams with increased permeability.

This paper describes a novel concept of producing energy efficient ”Maroon enriched natural gas “ and then Pink hydrogen” from any hydrocarbon base. The key idea is the extraction of hydrogen from water in addition to that from the hydrocarbon in an optimal fashion. This has the benefit of higher water vapor to CO2 exhaust ratio than conventional carbonaceous fuels when generating energy via combustion, a prudent step in achieving Netzero goals in a shorter time, and creating energy independence in most places.. The process of production makes concentrated CO₂ available for use and or sequestration. The process also maximizes use of renewable electricity in hydrogen generation, and maximizes use of existing infrastructure, with a minimum capital cost by energy recycle in the process. The process design applies sound thermodynamic principles which evolved during the nineteenth century, and mimics the geochemical processes going on in some of the natural 'colorless hydrogen'.

The annual energy matrix has been changing in the last years because of the necessity of less dependence on fossil fuels, which are running out on the planet. Therefore, a study was started to simulate the most efficient production of H2 through COMSOL Multiphysics®, as it is a gas that in the future will be essential to supply the world's energy necessities, due to its easy to get and insert in piped gas pipes. From this study, we were able to present an optimization of parameters that presents good indications of how to obtain efficient hydrogen production in an idealized reactor.

A major parameter controlling the extent and rate of oral drug absorption is permeability through the lipid bilayer of intestinal epithelial cells. Here, a biomimetic artificial membrane permeability assay (Franz-Bampa) was validated using Franz cells apparatus. Both high and low permeability drugs (metoprolol and mannitol, respectively) were used as external standards. Biomimetic properties of Franz-Bampa were also characterized by electron paramagnetic resonance spectroscopy (EPR). Moreover, the permeation profile for the 14 BCS class I-IV drugs cited in the FDA guidance (including other drugs as acyclovir, cimetidine, diclofenac, ibuprofen, piroxicam, and trimethoprim) were measured across Franz-Bampa. Apparent permeability (Papp) was compared to literature fraction dose absorbed in humans (Fa%). Papp in Caco-2 cells and Corti artificial membrane were likewise compared to Fa% to assess Franz-Bampa performance. Mannitol and metoprolol Papp values across Franz-Bampa were lower (3.20 x 10-7 and 1.61 x 10-5 cm/s, respectively) than those obtained across non-impregnated membrane (2.27 x 10-5 and 2.55 x 10-5 cm/s, respectively), confirming lipidic barrier resistivity. Performance of the Franz cell permeation apparatus using an artificial membrane showed similar log linear correlation (R2 = 0.664) with Fa%, as seen for Papp in Caco-2 cells (R2 = 0.805). Data support the validation of the Franz-Bampa method for use during drug discovery process.

Membranes are a selective barrier that allows certain species (molecules and ions) to pass through while blocking others. Some rely on size exclusion, where larger molecules get stuck while smaller ones permeate through. Others use differences in charge or polarity to attract and repel specific species. Membranes can be used to purify air and water by allowing only air and water molecules to pass through but preventing contaminants such as microorganisms and particles or to separate target gas or vapor, such as H2, CO₂, from other gases. The higher the flux and selectivity, the better a material is for membranes. The desirable performance can be tuned through material type (polymers, ceramics, and biobased materials), microstructure (porosity and tortuosity), and surface chemistry. Most membranes are made from plastic from petroleum-based resources, which contribute to global climate change and plastic pollution. Cellulose can be an alternative sustainable resource to make renewable membranes. Cellulose exists in plant cell walls as natural fibers, which can be broken down into smaller components such as cellulose fibrils, nanofibrils, nanocrystals, and cellulose macromolecules through mechanical and chemical processing. Membranes made from reassembling these particles and molecules have variable pore architecture, porosity, and separation properties and therefore have a wide range of applications in nano-, micro-, and ultrafiltration or forward osmosis. Despite their advantages, cellulose membranes face some challenges. Improving the selectivity of membranes for specific molecules often comes at the expense of permeability. The stability of cellulose membranes in harsh environments or under continuous operation needs further improvement. Research is ongoing to address these challenges and develop advanced cellulose membranes with enhanced performance. This article reviews the microstructure, fabrication methods, and potential applications of cellulose membranes, providing some critical insights into processing-structure-property relationships for current state-of-the-art cellulosic membranes that could be used to rationally improve their performance.

In order to further control the equivalent circulating density,a new type of annular pres-sure-reducing downhole tool for high temperature and high pressure wells-liquid-absorbing ECD tool is designed.Through this tool,the bottom hole pressure of the equivalent circulating drilling fluid can be close to its hydrostatic pres-sure,therebyachieving a deeper drilling depth.The tool is mainly composed of screw mo-tor,vortex blade,annular seal,universal joint and drill string.Its working principle is mainly to use the liquid absorption effect of the tool and the hydraulic energy of the circu-lating fluid extracted by the screw motor to convert it into mechanical energy,and to gen-erate suction force to improve the flow energy of the drilling fluid in the bottom hole an-nulusand reduce the equivalent circulation density.Based on ANSYS-FLUENT analysis andsimulation,the change of pressure drop characteristics under different drilling fluid density,displacement and tool size was simulated.The simulation results show that thedepressurization effect is 1.0MPa when the drilling fluid density is 1.2g/cm3. When the drilling fluid density is 1.5g/cm3,the depressurization is about 1.7MPa,and when thedrill-ing fluid density is 1.8g/cm3,the depressurization is about 1.9MPa.When the drilling fluid density is 2.0g/cm3,the pressure drop is about 2.3MPa.When the flow rate is from 1500-2500L/min,the maximum pressure can be reduced by 2.3MPa.When the viscosity is 40mPa•S and 60mPa•S,the pressure drop almost does not change.The increase of viscosi-ty has little effect on the pressure drop,and it is mainly affected by the flow rate under equal displacement.

The thermal surface properties of graphenes and carbon materials are of crucial importance in chemistry of materials, chemical engineering, and many industrial processes. (1) Background: The determination of these surface properties is carried out using inverse gas chromatography at infinite dilution which leads to the retention volume of organic solvents adsorbed on solid surfaces. This experimental and fundamental parameter actually reflects the surface thermodynamic interactions between injected probes and solid substrates. (2) Methods: The London dispersion equation and the Hamieh thermal model were used to quantify the London dispersive and polar surface energy of graphenes and carbon fibers as well their Lewis acid-base constants by introducing the coupling amphoteric constant of materials. (3) Results: The London dispersive and polar acid-base surface energies, the free energy of adsorption, the polar enthalpy and entropy, and the Lewis acid-base constants of graphenes and carbon materials were determined. (4) Conclusions: it was showed that graphene exhibited the highest values of London dispersive surface energy, polar surface energy, and Lewis’s acid-base constants. These highest characteristics of graphene justify its great potentiality and uses in many industrial applications.

The controls of depositional environments on reservoir quality have been evaluated in terms of porosity and permeability of the Gabo Field, Niger Delta, Nigeria. Data used in this research include Well logs, Core data and photos, and grain size analysis for Wells 51 and 52 in the study area. Standard methods as applicable in petrophysical and sedimentological analysis has been adopted. Thirteen reservoir units have been identified in wells 51 and 52 which had 5 reservoirs cored each. The lithofacies units of the identified reservoirs across the study area, comprise pebbly sands, coarse -, medium -, fine- and very fine-grained sands, sandy mud, silty sands and heteroliths. The heteroliths – very fine-grained silty muds are highly bioturbated. Ophiomorpha and skolithos are the major trace fossils with sedimentary structures (ripple lamination, wavy lenticular and planar beds, cross bedded sands, coarsening and fining upward). The facies associations interpreted for the study area are Channel and Coastal barrier systems and the environment of deposition as distributary channel, upper and lower shoreface. The sedimentary processes that deposited facies ranged from high energy regimes, reworking by waves to low energy with periodic influx of silts and muds. The average porosity and permeability for reservoirs in Well 51 is 16.7% and 1317 Md, reservoirs in Well 52 is 28.2% and 2330Md whereas porosity range for the study area is 2% - 32% and permeability is 1.2 – 10600 Md. The reservoir quality reservoir of the sand units in Well 51 (7, 9 and 13) and Well 52 (5, 7, 9, 11 and 13) is excellent - good, this is because of the dynamics environments of deposition (upper shoreface and distributary channel) as well as the mechanisms that play out during deposition such as bioturbation, sorting, sedimentary structures formed. Whereas the poor quality across the reservoirs especially the lower shoreface and prodelta facies is as result of lack bioturbation, connectivity, multiplicity of burrows that may have been plugged by clay and intercalation of shale and sand (heteroliths). This research has shown that environments of deposition have direct influence the reservoir quality in terms of porosity and permeability.

Abstract: Comparing outcrop data to laboratory results is important to verify and validate experiments of analogue and reservoir materials especially regarding conditions for deformation experiments. This is important better understand highly complex carbonate reservoir strata and their response to changes in subsurface conditions, reducing subsurface uncertainty. This study develops methods to allow for a more straightforward comparison of outcrop data (m-scale) with experimentally created fracture arrays developed in cylindrical samples (cm-scale). The main objective is to assess usefulness of experimentally-produced fracture networks as analogues for subsurface structures, typically at the meter and above scale by developing new techniques to use the lab deformation. It analyses key characteristics of laboratory-induced fracture networks by adapting scanline methods to use with x-ray tomography (XRT) images to allow for comparison with outcrop and field data. To test and verify these new methods two low permeability carbonate samples were used for deformation testing and analysis. Applying the different scanline methods we show that they can be used to analyse lab induced fractures (mm to cm-scale) identified in XRT images for comparison with outcrop data (m-scale). In addition, these methods also allow for quantification of fracture network attributes e.g. fracture spacing, fracture apertures, orientation. This new data bridges the gap between micro-scanlines using thin sections and outcrop scanlines.

In this study, a novel flexible ethanol gas sensor was created by the deposition of CoFe2O4 (CFO) thin film was on a thin mica substrate using pulsed laser deposition. Transition electron microscopy (TEM) investigations clearly demonstrated the successful growth of CFO on the mica, where a well-defined interface was observed. Ethanol gas-sensing studies showed optimal performance at 200 °C, with the highest response, 19.2, to 100 ppm ethanol. Operating the sensor in self-heating mode under 7 V applied voltage, which was corresponds to a temperature of approximately 200 °C, produced a maximal response to ethanol of 19.2. This aligned with the highest responses observed during testing at 200 °C, confirming the sensor’s accuracy and sensitivity to ethanol under self-heating conditions. In addition, the sensor exhibited good selectivity to ethanol and excellent flexibility; maintaining its high performance after bending and tilting up to 5000 times. As this is the first report on flexible self-heated CFO gas sensors, we believe that this research holds great promise for the future development of high-quality sensors based on this approach.

In the article we present the results concerning the impact of structural and chemical properties of zinc oxide in various morphological forms, on its gas-sensitive properties tested in an atmosphere containing a very aggressive gas such as chlorine. Two types of ZnO sensor layers obtained by two different technological methods were used. Their morphology, crystal structure, specific surface area, porosity, surface chemistry and structural defects were characterized, and then compared with gas-sensitive properties in a chlorine-containing atmosphere. To achieve this goal scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and photoluminescence spectroscopy (PL) methods were used. The sensing properties of obtained active layers were tested by temperature stimulated conductance method (TSC). We have noticed that their response in chlorine atmosphere is not determined by the size of the specific surface or porosity. The obtained results showed that the structural defects of ZnO crystals play the most important role in chlorine detection. We demonstrated that the Cl2 adsorption is a concurrent process to oxygen adsorption. Both of them occur on the same active species (oxygen vacancies). They concentration is higher on the side planes of the zinc oxide crystal than the others. Thanks to the conducted studies authors demonstrated that to develop a new gas sensor devices not only changing of active layer chemical composition but also controlling its crystal structure and morphology could be used.

Natural gas is an important energy source among various fossil fuels. However, natural gas typically contains a significant amount of water vapor, which can pose challenges in its usage. Therefore, the process of removing water vapor from natural gas, known as gas dehydration, is crucial in the gas industry. The presence of water vapor in the gas supply can lead to the formation of hydrates, which can cause issues such as blockages in pipelines. To tackle this problem effectively, gas dehydration makes use of Tri ethylene glycol (TEG) as a drying agent. TEG works by selectively absorbing water vapor from the natural gas flow, thereby significantly reducing its moisture content.In the gas dehydration process, wet gas is treated by using lean glycol in an absorber, where the water vapor is removed. The resulting rich glycol is then recovered and recycled for further use. In this study, we explore the possibility of replacing nitrogen with dry natural gas in the re-generator of the glycol dehydration system. The aim is to evaluate the feasibility and effectiveness of this alternative approach. To assess the performance of both techniques, we employed HYSYS modeling and simulation. Through this analysis, we compared the capital and utility expenses associated with each method while ensuring that the glycol purity requirements remained unchanged. By examining the results obtained from the simulations, we can gain insights into the economic viability and efficiency of utilizing dry natural gas in the re-generator stage of the glycol dehydration process.In addition to the primary purpose of removing water vapor, the wet gas obtained from the stripping mechanisms in the glycol dehydration process can serve additional functions. It can be utilized to power steam pumps and compressors, thereby maximizing energy efficiency within the system. Alternatively, the wet gas can be recycled back into the process for further treatment. To develop a comprehensive understanding of the entire mechanism, we constructed a model based on the actual flow diagram. This model takes into account the various components and processes involved in the glycol dehydration system, including the stripping mechanisms and their connection to other equipment. By analyzing the data and outcomes generated by this model, we can derive valuable insights. These findings can be utilized to optimize the heat and material balance within the plant, ensuring efficient operation and potentially leading to the design of an improved system in terms of energy consumption and overall performance

Among other fossil fuels, natural gas is a major energy source. It is generally created saturated with water vapor. Dehydration of natural gas is vital in the gas business to remove water vapor from the gas supply, which may cause hydrate development in pipes. Gas dehydration employs Tri ethylene glycol (TEG) to remove water vapor from natural gas flow. The wet gas is dehydrated with lean glycol in an absorber, and the rich glycol is recovered and reused. This work investigates the use of dry natural gas instead of nitrogen in the glycol dehydration re-generator, and compares the results using HYSYS modeling and simulation. The two techniques were compared for capital and utility expenses, while maintaining the identical glycol purity criteria. The wet gas from the stripping mechanisms may also be utilized to run steam pumps and compressors or recycled. The model is based on the real mechanism flow diagram. Finally, the findings of this model might be used to design a new heat and material balance for the plant.

The available direct gas dynamic tables provide the area ratio and the Prandtl-Meyer(P-M) angle of isentropic expansion of gas as functions of the Mach number. But finding the value of the Mach number in terms of area ratio or P-M angle requires an inverse function. Currently, the Mach number is determined by either interpolation from the direct gas dynamics tables, or the application of non-linear equation solvers using numerical methods. Both methods are approximate. In this paper inverse functions for Mach number in the form of Taylor’s series expansions are reported to develop the so-called inverse tables. The advantage of this approach is that the Mach number with a greater accuracy, referred to as nearly exact can be obtained by reading from the inverse table. In the presentation, the necessary equations and new tables that can be used by the scientific community will be disseminated. The data and computer programs are made available on GitHub through https://github.com/anillals/Inverse-gas-dynamic-tables- and-codes. A paper describing the complete mathematical steps in the derivation of the equations can be found at https://rdcu.be/dgrlf

Eddy current sensors can be used to test the characteristics and measure the parameters of the conductive samples. As the main obstacle of the multi-frequency eddy current sensor, the lift-off distance affects the effectiveness and accuracy of the measurement. In this paper, a material-independent algorithm has been proposed for the restoration of the lift-off distance when using the multi-frequency eddy current sensor, which is based on the approximation under the thin-skin effect. Experiment testing on the performance of the proposed method is presented. Results show that from the dual-frequency inductance, the lift-off distance could be restored with a maximum error of 0.24 mm for the distance up to 12 mm. Besides, the derived lift-off distance is used for the inversion of the magnetic permeability. Based on a lift-off insensitive inductance (LII) feature, the magnetic permeability of steels can be inversed in an iterative manner, with an error of less than 0.6 % for the lift-off distance up to 12 mm.

The temperature effect plays an important role for an accurate determination of the polar free energy, polar thermodynamic parameters, and enthalpic and entropic Lewis’s acid base properties of oxides, polymers and composites polymers/oxides. The adsorption of polymers on other solid surfaces is crucial in many industrial applications, coatings, paints, catalysis, colloids and adhesion processes. (1) Background: Inverse gas chromatography at infinite was used for the physico-chemical characterization of solid substrates by determining the thermodynamic parameters of adsorption of model organic solvents on solid surfaces such as polymers, metallic oxides, carbon fibers, pharmaceutical or 3D/4D printing substrates. (2) Methods: A new method based on the London dispersion equation was applied with a new parameter associating the deformation po-larizability and the harmonic mean of the ionization energies of solvent. More accurate values of the dispersive and polar interaction energies of the various organic solvents adsorbed on PMMA in bulk phase and PMMA/silica at different recovery fractions were obtained as well as the Lewis acid-base parameters and the transition temperatures of the different composites. (3) Results: This new methodology gave very interesting results on the behavior of PMMA adsorbed on silica. An important effect of the temperature and the recovery fraction on the various physicochemical and thermodynamic properties was highlighted. The variations of all interaction parameters showed the presence of three transition temperatures for the different PMMA adsorbed on silica with the various coverage rates with a shift of these temperatures for a recovery fraction of 31% (4) Con-clusions: An important variation of the polar enthalpy and entropy of adsorption, the Lewis ac-id-base parameters and the intermolecular separation distance as a function of the temperature and the recovery fraction of PMMA on silica.

This research evaluated the role and feasibility of the granular nanocellulose particles (GNC) from sugarcane bagasse obtained from enzymatic hydrolysis in reducing lipid digestibility and permeability in the in vitro simulated gastrointestinal (GI) system. GNC concentration (0.02%, w/v) had significantly affected the released free fatty acid (FFA) reduction of approximately 20%. The Pick-ring emulsion of the GNC and olive oil simulation mixture revealed higher oil droplet size distribution and stability in the initial stage than the vortexed mixture formation. The difference in particle size distribution and zeta potential of the ingested GNC suspension and GNC-olive oil emulsion were displayed during the in vitro gastrointestinal simulation. GNC particles interacted and distributed surrounding the oil droplet leading to the interfacial emulsion. The GNC concentration (0.01-0.10%, w/v) showed low toxicity on the HIEC-6 cell, ranging from 80.0 to 99% of cell viability. The release of FFA containing the ingested GNC suspension and GNC-olive oil emulsion was about 30% reduction compared to without GNC digest solution. The FFA and triglyceride permeability through the HIEC-6 intestinal epithelium monolayer were deceased in the digesta containing the ingested GNC and emulsion. This work indicated that GNC represented a significantly critical role and properties in the GI tract and reduced lipid digestion and absorption. This GNC could be utilized as an alternative food additive or supplement in fatty food for weight control due to their inhibiting lipid digestibility and assimilation.

Dynamic virtual testing by Hardware in the Loop (HIL) real time simulation systems is common to minimize physical tests to validate and verify control algorithms, logics and software, under normal and emergency conditions. The accurate but costly HIL models setup activities could have an extended use to simulate faulty conditions that are seldom observable in the real system, yet they must be detected in advance and recognized. Data driven diagnostic methods have reached a mature development, in various sectors, proving effective in early detecting slowly varying deviations from nominal patterns of signals, even without a priori knowledge of their nature and behavior. These methods rely on vast amount of data logged from real systems that are ever and ever richer of monitoring telemetries that are worth being exploited. However, due to the usually reliable and safe systems being managed, it is often difficult to collect enough data on anomalous situations to validate fault detection and isolation and limit false positives. HIL model-based simulations allow generating and observing operational domains or transients rarely observed in real operations. This allows identifying the signals that are most correlated to faults and that could be selected to setup data-based diagnostic models of parts or subsystems, which are more suitable than the whole HIL model for online diagnostics, as well as to identify the features and trends that are most symptomatic of anomalous conditions.

The vacuum preloading method effectively strengthens the soft soil foundations with vertical drainage, which will produce a smear effect when laying sand drains. Meanwhile, the seepage of pore water and soil deformation during consolidation exhibits nonlinear characteristics. Therefore, based on Gibson's 1D large strain consolidation theory, this paper developed a more generalized large strain radical consolidation model of sand-drained soft foundations under free strain assumption. In this system, the double logarithmic compression permeability relationships for soft soils with large strain properties, the variation of the radical permeability coefficient in the smear zone, and the effect of the non-Darcy flow were all included. Then, the partial differential control equations were numerically solved by the finite difference method and validated with existing radical consolidation test results and derived analytical solutions. Finally, the influences of relevant model parameters on consolidation are discussed. The analysis shows that the greater the maximum dimensionless vacuum negative pressure P0, the faster the consolidation rate of sand-drained foundations. Meanwhile, the decrease in the negative pressure transfer coefficient k1 will result in a decreasing final settlement amount. Moreover, the consolidation rate of sand-drained foundations is slower considering the non-Darcy flow, but the final settlement is unaffected.

Three-dimensional (3D) facies and petrophysical models were generated from previously published data of carbonate strata in the Dam Formation (eastern Saudi Arabia) to quantitatively investigate, describe, understand, model, and predict the permeability anisotropy of tidal flat carbonate within a sequence stratigraphic framework. The resulting 3D models were used to conduct fluid flow simulations to demonstrate how permeability anisotropy influences the production of hydrocarbons and ultimately affects decisions concerning future drilling in the exploration and development of carbonate reservoirs that have tidal flat strata. The constructed 3D facies model consists of four lithofacies associations, two of which were grain-dominated associations and two of which were mud-dominated associations. These lithofacies associations varied spatially in four reservoir zones (zones 1 to 4), which represent two fourth-order sequences in the uppermost part of the Dam Formation. Zones 1 and 3 consist of transgressive parasequences, and zones 2 and 4 consist of the regressive parasequences of these sequences. The 3D porosity and permeability models have a coherent match with the distribution of the lithofacies and the stratigraphic framework of the Dam Formation. The results suggested that the permeability anisotropy in zones 1 and 3 is controlled by the occurrence of the grain-dominated lithofacies associated with tidal flat channels. This lithofacies association overlies the sequence boundaries of sequences 1 and 3, forms reservoir bodies with relatively high permeability values, and is elongated perpendicular to the shoreline of the depositional environments. In contrast, permeability anisotropy in zones 2 and 4 is thought to be controlled by the occurrence of the grain-dominated lithofacies associated with the oolitic shoal. This lithofacies association overlies the maximum flooding surface of sequences 2 and 4, forms reservoir bodies with relatively high permeability values, and is elongated parallel to the shoreline of the depositional environments. Fluid flow simulation results suggested that the trend in hydrocarbon production from the constructed 3D models depends on permeability anisotropy in each reservoir zone. Thus, recognizing trends in permeability anisotropy, which might be predicted using sequences stratigraphy, could help to identify potential areas for future drilling.

Rapid and extensive urbanization has adversely impacted humans and ecological entities in the recent decades through a decrease in surface permeability and the emergence of urban heat islands (UHI). While detailed and continuous assessments of surface permeability and UHI are crucial for urban planning and management of landuse zones, they have mostly involved time consuming and expensive field studies, and single sensor derived large scale aerial and satellite imageries. We demonstrated the advantage of fusing imageries from multiple sensors for landuse and landcover (LULC) change assessments as well as for assessing surface permeability and UHI emergence in Tirunelveli, Tamilnadu, India. Cartosat-2 and Landsat-7 ETM+ imageries from 2007 and 2017 were fused and classified using a Rotation Forest (RF), while surface permeability and temperature were quantified using Soil-Adjusted Vegetation Index (SAVI) and Land Surface Temperature (LST) index, respectively. Fused images exhibited higher classification accuracies than non-fused images, i.e. overall kappa coefficient values 0.83 and 0.75, respectively. We observed an overall increase of 20 km2 (45%) in the coverage of urban (dry, real estate plots and built-up) areas, while a decrease of 27 km2 (37%) for vegetated (cropland and forest) areas in Tirunelveli between 2007 and 2017. The SAVI values indicated an extensive decrease in surface permeability for Tirunelveli overall (0.4) and also for almost all LULC zones. The LST values exhibited an associated overall increase (1.30C) of surface temperature in Tirunelveli with the highest increase (2.40C) for urban built-up areas between 2007 and 2017. The SAVI-LST combined metric depicted the Southeastern built-up areas in Tirunelveli as a potential UHI hotspot, while a caution for the Western riparian zone for UHI emergence in 2017. Our results provide important metrics for surface permeability and UHI monitoring, and inform urban and zonal planning authorities about the advantages of satellite image fusion.

Dielectric barrier discharge (DBD) plasma has several applications in different fields. One of these fundamental applications is medical usages, where various methods are employed to improve the plasma treatment process. The combination of different gases is one of the important strategies to improve the performance of plasma in treatment. In this paper, the optimized plasma parameters for one-dimensional radiofrequency discharge produced at low pressures in a helium gas combination is studied. In this research, the optimal combination of H₂O and He is identified to attain the highest amount of reactive oxygen species (ROS). Considered mixture are 5,10,15 and 20 precent of H₂O for one dimensional helium gas discharge. The results show that the parameters of the output plasma are highly dependent on the composition of the input gases. It is found that the greatest concentrations of H+, He+, Hes (excited helium), and OH/ densities are observed when the H₂O percentage is 10%. Moreover, the density distributions of various species and the temperatures of electrons are numerically calculated during the electrical discharge process. These findings provide useful knowledge on how to optimize plasma parameters for biomedical applications, which may lead to improved treatment results in several therapeutic areas.

This study addresses the importance of conducting mass movement susceptibility mapping and hazard assessment using quantitative techniques, including machine learning, in the Northern Lima Commonwealth (NLC). Previous exploration of the topographic variables revealed high correlation and multicollinearity among some of them, which led to dimensionality reduction through principal component analysis (PCA). Six susceptibility models were generated using weights of evidence, logistic regression, multilayer perceptron, support vector machine, random forest, and naive Bayes methods to produce quantitative susceptibility maps and assess the hazard associated with two scenarios: the first being an El Niño phenomenon and the second being an earthquake exceeding 8.8Mw. The main findings indicate that machine learning models exhibit excellent predictive performance for the presence and absence of mass movement events, as all models surpassed an AUC value of >0.9, with the random forest model standing out. In terms of hazard levels, in the event of an El Niño phenomenon or an earthquake exceeding 8.8Mw, approximately 40% of the NLC area would be exposed to the highest hazard levels. It also highlights the importance of integrating methodologies to reduce model uncertainty, such as comprehensive analysis of variables supported by high quality data and organized workflows. The findings of this research are expected to serve as a supportive tool for land managers in formulating effective disaster prevention and risk reduction strategies.

Inverse gas chromatography at infinite dilution was used to determine the surface thermodynamic properties of silica particles and PMMA adsorbed on silica, and more particularly, to quantify the London dispersive energy γsd, the Lewis acid γs+ and base γs- polar surface energies of PMMA/silica composites as a function of the temperature and the recovery fraction θ of PMMA. The polar acid–base surface energy γsAB and the total surface energy of the different composites were then deduced as a function of the temperature. In this paper, the Hamieh thermal model was used to quantify the surface thermodynamic energy of poly methyl methacrylate (PMMA) adsorbed on silica particles at different recovery fractions. A comparison of the new results was carried out with those obtained by applying other molecular models of the surface areas of organic molecules adsorbed on the different solid substrates. An important deviation of these molecular models from the thermal model was proved. The determination of γsd, γs+, γs-, and γsAB of PMMA in both bulk and adsorbed phases showed an important non-linearity variation of these surface parameters as a function of the temperature. The presence of maxima in the curves of γsd(T) highlighted the second order transition temperatures in PMMA showing beta-relaxation, glass transition and liquid-liquid temperatures. These three transition temperatures depended on the adsorption rate of PMMA on silica. The proposed method gave a new relation between the recovery fraction of PMMA and its London dispersive energy showing an important effect of the temperature on the surface energy parameters of adsorption of PMMA on silica. A universal equation relating γsd(T,θ) of the systems PMMA/silica to the recovery fraction and the temperature was proposed.

This research was devoted to study the effect of the tacticity of PMMA on the surface physicochemical properties such as the London dispersive component of the surface energy of the polymer, the polar and dispersive free energies, the Lewis’s acid-base surface parameters, and the Lewis acid and base surface energies of atactic, isotactic and syndiotactic PMMAs as a function of the temperature. Inverse gas chromatography (IGC) at infinite dilution was used to determine the surface thermodynamic properties of PMMA at different tacticities. The experimental values of the net retention time and volume of model organic molecules adsorbed on the atactic, isotactic and syndiotactic PMMAs, were obtained by IGC technique at infinite dilution. The London dispersion interaction energy was used for the separation of the polar and dispersive energy of the different n-alkanes and polar solvents adsorbed on the different PMMA surfaces. The London dispersive surface energy γ_s^d (T) of PMMAs was determined by applying the Hamieh thermal model that took into account the effect of the temperature on the surface area of adsorbed molecules. The obtained results showed non-linear variations of γ_s^d (T) of atactic, isotactic, and syndiotactic PMMAs with three maxima characterizing the three transition temperatures of PMMAs, T_g, T_g and T_(liq-liq) with a shift of these temperatures with the isotactic and syndiotactic PMMAs. It was showed that the polar interaction free energy ∆G_a^p (T) also showed the presence of the three above transition temperatures of the polymers. The study showed an important non-linearity variation of the different acid-base parameters in the various polymer surfaces proving the highest effect of the temperature and the tacticity on these parameters. The determination of the enthalpic and entropic Lewis’s acid-base parameters showed an amphoteric character for the different PMMAs. The basicity of the atactic PMMA was about four times larger than its acidity outside the neighborhood of the transition temperatures of the polymer. Whereas, the isotactic PMMA was about 2 to 2.5 times more basic than acid, while the syndiotactic PMMA exhibited the highest basicity by showing a surface 5 to 8 times more basic than acid. However, the Lewis acid-base parameters strongly depended on the temperature and sudden variations of these surface parameters were observed around the transition temperatures largely depending on the PMMA tacticity. The determination of the polar acid and base surface energies of the three PMMAs led to the same previous transition temperatures with an important effect of the tacticity of PMMA on the values of these acid-base surface energies.

A growing number of companies in the brewery industry have made commitments to measure and reduce their greenhouse gas (GHG) emissions. However, many brewers, particularly craft brewers with relatively low rates of production, have struggled to meet these commitments. The purpose of this research was to investigate the challenges and benefits of measuring and reducing GHG emissions in the craft brewery industry. The research was conducted in Ontario, Canada, which has seen strong recent growth in the craft brewery industry. A case study and semi-structured interviews among Ontario Craft Brewers were conducted. The case study found that indirect (scope 3 emissions under the WBCSD & WRI GHG Protocol) GHG sources accounted for 46.4% of total GHGs, with major sources from barley agriculture, malted barley transportation, and bottle production. Direct emissions (scope 1) accounted for only 14.9% of GHGs, while scope 2 emissions, comprised mainly of energy consumption, accounted for 38.7% of GHGs. The case study and interviews found that the main challenges in calculating brewery GHGs are secondary data availability, technical knowledge, and finances. The study also found that the main benefits for Ontario breweries to measure their GHGs include sustainability marketing and preserving the environment. The interviews also found a poor understanding of carbon regulation among Ontario Craft Brewers, which is interesting considering that Ontario implemented a provincial cap and trade program in 2017.

Development of new neurotherapeutics is strongly depending on appropriate animal model chosen in preclinical studies. A cuprizone model is an effective tool for studying demyelination and re-myelination processes in the brain, but BBB integrity in cuprizone model is still a topic for debate. Several publications claim that BBB remains intact during cuprizone-induced demyelination; others demonstrate results that could be explained by the increased BBB permeability. In our work we aim to analyze permeability of BBB for different macromolecules, particularly, antibody-conjugates in cuprizone-intoxicated mice. We compared the traditional approach using Evans blue injection with following dye extraction and detection of antibody-conjugates using magnetic resonance imaging (MRI) and confocal microscopy to analyze BBB permeability in cuprizone model. First, we validated our model of demyelination by detecting changes in gene expression of myelin basic protein and proteolipid protein, and by performing MRI and histological analysis. Our results suggest that the methods with better sensitivity were able to detect the accumulation of macromolecules (such as fluorescent-labeled or gadolinium-labeled antibody conjugates) in the brain, suggesting a local BBB disruption in the demyelinating area. These findings support previous investigations that ques-tioned BBB integrity in cuprizone model and demonstrate possibility for delivery of anti-body-conjugates to demyelinated corpus callosum

Aquaporins (AQPs) are water channels widely distributed in living organisms and involved in many pathophysiologies as well as in cell volume regulations (CVR). In the present study, based on the structural homology existing between mineralocorticoids receptors (MR), glucocorticoids receptors (GR), cholesterol consensus motif (CCM) and the extra-cellular vestibules of AQPs, we investigated the binding of corticosteroids on AQP family through in silico molecular dynamics simulations of AQP2 interactions with cortisol. We propose for the first time a putative AQPs corticosteroids binding site (ACBS) and discussed its conservation through structural alignment. Corticosteroids can mediate non-genomic effects, nonetheless, the transduction pathways involved are still misunderstood. Moreover, a growing body of evidence is pointing out toward the existence of a novel membrane receptor mediating part of these rapid corticosteroids effects. Our results suggest that the naturally produced glucocorticoid cortisol inhibits channel water permeability. Based on these results, we propose a detailed description of a putative underlying molecular mechanism. In this process, we also bring new insights on the regulatory function of AQPs extra-cellular loops and on the role of ions in tuning the water permeability. Altogether, this work brings new insights into corticosteroids non-genomic effects through the proposition of AQPs as membrane receptor of this family of regulatory molecules. This original result is the starting point for future investigations to define more in depth and in vivo the validity of this functional model.

Electromagnetic sensing has been used for diverse applications of non-destructive testing, including the surface inspection, measurement of properties, object characterization. However, the measurement accuracy could be significantly influenced by the lift-off between sensors and samples. To address the issue caused by lift-offs, various strategies have been proposed for the permeability measurement of ferromagnetic steels, which mainly involves different sensor designs and signal features (e.g., the zero-crossing feature). In this paper, a single high-frequency scenario for the permeability retrieval is introduced. By combining the signal of two sensing pairs, the retrieval of magnetic permeability is less affected by the lift-off of sensors. Unlike the previous strategy on reducing the lift-off effect (directly taking the phase term out of the integration) using the Dodd-Deeds analytical method, the proposed method is based on a high-frequency linear feature of the phase term. Therefore, this method has the merit of high accuracy and fast processing for the permeability retrieval (a simplified version of Dodd-Deeds analytical formulas after the integration). Experimental measurement has been carried out on the impedance measurement of designed sensors interrogating ferromagnetic dual-phase steels. For sensor lift-offs of up to 10 mm, the error of the permeability retrieval is controlled within 4 % under the optimal frequency.