A portable laser photoacoustic sensor based on a Field-Programmable Gate Array (FPGA) is reported for methane detection. A tunable DFB diode laser in the 1654 nm wavelength range is used as an excitation source. The photoacoustic signal processing was implemented by a FPGA device. A small resonant photoacoustic cell is designed. The minimum detection limit (1σ) of 10 ppm for methane (CH₄) is demonstrated.

In this study a material based on Polyethylene (PE) and Microcrystalline Cellulose (MC) was developed as a breathable packaging film. Surface functionalization of MC with 3 aminopropyltriethoxysilane (APTES) shows to be an efficient alternative to tailor their properties and increase opportunities for the application of MC on the reinforcement of polymers such polyethylene (PE). Functionalization of MC with mentioned silane derivative was achieved using a green method and later used on the development of composites with PE in three percentages (1, 3 and 5%). All the materials were prepared by melt blending and characterized, in terms of structural properties (ATR-FTIR and FTIR in transmittance, EDX, SEM), thermal properties (DSC and TGA), thermomechanical properties (DMA), contact angle measurements and permeability to oxygen and water vapor. The materials demonstrated to have potential to be used as breathable film packaging of fresh products.

Citrus waste has been used as a source of bioplastic research in different ways. Because the juice industry produces significant amounts of residue each year, it would be advantageous to use the byproducts in the creation of new materials. For many years, researchers have been investigating an environmentally friendly way to take citrus and other organic waste and turn it into polymers that may be used, for instance, to produce bio-based and biodegradable films for food packaging. The goal of this study is to create biofilms from orange (OW) and ginger waste (GW) using an ultrafine grinder and study the films' properties. Since pectin has the ability to gel and because cellulosic fibres are strong, citrus waste has been studied for its potential to produce biofilms. After being washed, dried, and milled, orange and ginger waste were shaped into films using a casting process. Tensile testing was used to determine the mechanical properties of biofilms, while dynamic mechanical thermal analysis (DMTA), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC) were used to determine their thermal properties. As the number of grinding cycles increased, the suspension's viscosity increased from 29 to 57 mPa.s for OW and from 217 to 376 mPa.s for GW while the particle size in the suspension significantly decreased. For OW and GW films, the highest tensile strength was 17 MPa and 15 MPa, respectively. The maximum strain obtained among all films was 4.8%. All the tested films were stable up to 150°C, and maximum degradation occurs after 300°C.

Today, enhancing food preservation and safety in the spirit of the bioeconomy suggests the use of biodegradable polymers such as poly-L-lactic acid (PLA) in food packaging and the replacement of chemical additives with natural antioxidant/antibacterial agents such as essential oils and their derivatives. Herein a novel carvacrol (CV) @ natural zeolite (NZ) nanohybrid was developed by employing a new vacuum adsorption desorption method which results in the adsorption of a high CV amount on NZ equal to 61.7 %wt. This CV@NZ nanohybrid was successfully dispersed in a PLA/triethyl citrate (TEC) matrix via a melt-extrusion process to obtain PLA/TEC/xCV@NZ nanocomposite films with 5, 10 and 15 CV@NZ %wt. content. PLA/TEC/xNZ films were also de-veloped for comparison. The overall study resulted in a biodegradable active film with the fol-lowing properties: 10%wt. CV@NZ content (PLA/TEC/10CV@NZ), self-healable properties, 22% higher tensile strength and 40% higher elongation at break, 45% higher water barrier and 40% higher oxygen barrier than pure PLA/TEC matrix. This film also provides high CV release content, high CV control release rate as well as significant antioxidant activity and antibacterial activity against the food pathogens Staphylococcus aureus and Salmonella enterica spp. enterica serovar Typhimurium. This film not only succeeds in extending the shelf-life of fresh pork minced, as shown by total variable count measurements in four days, but also prevents lipid oxidation of fresh minced pork and maintains the minced meat in higher nutritional conditions, as revealed by the heme iron content determination, and in a much better and acceptable sensory condition than the commercial packaging paper.

The COVID-19 pandemic over the past years has shown a great need for rapid, low-cost and on-site detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). In this paper, an aptamer-based colloidal gold nanoparticle lateral flow test strip was well developed to realize the visual detection of wild type SARS-CoV-2 spike protein (SP) and multiple variants. Under the optimal reaction conditions, a low detection limit of SARS-CoV-2 S protein of 0.68 nM was acquired, and the actual detection recovery was 83.3% to 108.8% for real world samples. This suggests a potential tool for the prompt detection of SARS-CoV-2 with good sensitivity and accuracy, and a new method for the development of alternative antibody test strips for the detection of other viral targets.

Climate change, increasing global food needs, and decreasing global resources brought a new era to human every-day live with a strong turn to circular economy and sustainability. Food packaging and preservation is an important global sector where enchanced research is carried out. New methods such as active packaging and chemical preservatives replacement are of major interest. Many researchers were published studies about active packaging films, replacement of chemical preservatives with natural originated extracts, and novel incorporation procedures. Sequentially to our and other scientists’ previous work, in this paper we present the results of the improvement which was achieved by incorporating the developed nanohybrid of natural-halloysite/carvacrol-extract, the pure natural carvacrol extract and the commonly used low-density-polyethylene. The well known corona-treatment procedure was employed to produced the optimum final film and the results shown that the low-density-polyethylene incorporated with natural-halloysite/carvacrol-extract nanohybrid and coated external with extra carvacrol extract exhibited aproximatelly 100% higher Young-Modulus values, slightly decreased ultimate strength by 20%, and almost stable elonation at break properties. The water-vapor and oxygen barrier increased by 40%. Finally, the antioxidant activity of the corrona-treated film increased by 28% compared to the similar but untreated product because of the lower release rate of the carvacrol.

Intermetallic compounds are increasingly being expected to utilize in tribological environments, but to date the works are hindered by insufficient ductility at low and medium temperature. This paper presents a novel multiphase intermetallic alloy with the chemical composition of Mo-40Ni-13Si (at.%). Microstructure characterization reveals that a certain amount of ductile Mo phases formed during the solidification process of ternary Mo-Ni-Si alloy melt, which is undoubtedly beneficial to the ductility improvement of intermetallic alloy. Tribological properties of the designed alloy, including wear resistance, friction coefficient and metallic tribological compatibility, were evaluated under dry sliding wear test conditions at room temperature. Results suggested that the multiphase alloy possesses an excellent property for room-temperature wear applications, which is attributed to the unique microstructural features and thereby good combination in hardness and ductility. The corresponding wear mechanism is also reported by observing the worn surface, subsurface and wear debris of alloy, which to be found is soft abrasive wear.

Adenoviruses (Ads) have been extensively manipulated for the development of cancer selective replication, leading to cancer cell death or oncolysis. Clinical studies using E1-modified oncolytic Ads have shown that this therapeutic platform was safe, but with limited efficacy, indicating the necessity of targeting other viral genes for manipulation. To improve the therapeutic efficacy of oncolytic Ads, we treated the entire Ad genome repeatedly with UV-light and have isolated AdUV which efficiently lyses cancer cells as reported previously [1]. In this report, we show that no mutations were observed in the early genes (E1 or E4) of AdUV while several mutations were observed within the Ad late genes which have structural or viral DNA packaging functions. This study also reported the increased release of AdUV from cancer cells. In this study, we found that AdUV inhibits tumor growth following intratumoral injection. These results indicate the potentially significant role of the viral late genes, in particular the DNA packaging genes, to enhance Ad oncolysis.

In the past years, consumers have increased their interest to buy healthier food products, rejecting those products with more additives and giving preference to the fresh ones. Moreover, the current environmental situation has made society more aware of the importance of reducing the production of plastic and food waste. In this way and considering the Food Industry need of reducing the food spoilage along the food chain, edible coating has been considered as an eco-friendly food packaging that can replace traditional plastic packaging providing an improvement in the product’s shelf-life. Edible coating are thin layers applied straightaway on the food materials’ surface, that are made of biopolymers that usually incorporate other elements, such as nanoparticles or essential oils, to improve their physicochemical properties. These materials must provide a barrier that can prevent the pass of water vapor and other gasses, the microbial growth, the moisture loss, and the oxidation, so the shelf-life could be extended. The aim of this review was to compile the current data available to give a global vision of the formulation process and the different ways to improve the characteristics of the coats applied in both fruits and vegetables. In this way, the suitability of compounds in by-products produced during the Food Industry chain were also considered for the edible coating production.

By using the particle swarm optimization algorithm for crystal structure prediction, we reveal a newly orthorhombic Cmcm structure of HfB4, which is more energetically superior to the previously proposed YB4-, ReP4-, FeB4-, CrB4-, and MnB4-type structures in the considered pressure range. The phonon dispersion and elastic constants calculations confirm that the new phase is dynamically and mechanically stable. The calculated large shear modulus (240 GPa) and high hardness (45.7 GPa) imply that the predicted Cmcm-HfB4 is a potential superhard material. Meanwhile, the directional dependences of the Young's modulus, bulk modulus, and shear modulus for HfB4 are systematically investigated. Further analyses of the density of states and electronic localization function indicate that the strong B-B and B-Hf covalent bonds greatly contribute to its high hardness and stability.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

The influence of growth temperature on the crystalline quality and optical properties of AlGaN at 325 nm, grown using plasma-assisted molecular beam epitaxy (MBE), was investigated. The growth temperature exhibited a significant impact on the growth mode and surface morphology. Specifically, at a growth temperature of 750 degrees Celsius, when appropriate Al and Ga flow rates were employed, the AlGaN layer exhibited exceptional surface morphology and favorable optical properties. The optical properties of the AlGaN material were explored, revealing the presence of two distinct non-radiative recombination centers characterized by different activation energies. The minority carrier lifetimes were measured as 560 ps at 10 K and 64 ps at room temperature. The underlying mechanism was analyzed from the perspective of carrier dynamics, shedding light on the observed phenomena.

This study reports on the development of bio-based hydrophobic coatings for packaging papers through deposition of polyhydroxybutyrate (PHB) particles in combination with nanofibrillated cellulose (NFC) and plant wax. In a first approach, PHB particles in micrometer range (PHB-MP) were prepared through a phase-separation technique providing internally nanosized structures. The particles were transferred as a coating by dip-coating filter papers in the particle suspension, followed by sizing with a carnauba wax solution. This approach allowed partial to almost full surface coverage of PHB-MP over the paper surface resulting in static water contact angles of 105° to 122° and 129° to 144° after additional wax coating. In a second approach, PHB particles with submicron sizes (PHB-SP) were synthesized by an oil-in-emulsion (o/w) solvent evaporation method, and mixed in aqueous suspensions with 0 to 7 wt% NFC. After dip-coating filter papers in PHB-SP/NFC suspensions and sizing with a carnauba wax solution, static water contact angles of 112° to 152° were obtained. The intrinsic properties of the particles were analyzed by scanning electron microscopy, thermal analysis and infrared spectroscopy, indicating higher crystallinity for PHB-SP than PHB-MP. The chemical interactions between the more amorphous PHB-MP particles and paper fibers were identified as an esterification reaction, while the morphology of the NFC fibrillar network was playing a key role as binding agent in the retention of more crystalline PHB-SP at the paper surface, hence contributing to higher hydrophobicity.

Tellurium exhibits exceptional intrinsic electronic properties. However, investigations into the modulation of tellurium's electronic properties through physical modification are notably scarce. Here, we present a comprehensive study focused on the evolution of the electronic properties of tellurium crystal flakes under plasma irradiation treatment by employing conductive atomic force microscopy and Raman spectroscopy. The plasma-treated tellurium experienced a process of defect generation through lattice broken. Prior to the degradation of electronic transport performance due to plasma irradiation treatment, a remarkable observation emerged: in the low-energy region of hydrogen plasma-treated tellurium, a notable enhancement in conductivity was unexpectedly detected. The mechanism underlying this enhancement in electronic transport performance was thoroughly elucidated by comparing it with the electronic structure induced by argon plasma irradiation. This study not only fundamentally uncovers the effects of plasma irradiation on tellurium crystal flakes, but also unearths an unprecedented trend of enhanced electronic transport performance at low irradiation energies when utilizing hydrogen plasma. This abnormal trend bears significant implications for guiding the prospective application of tellurium-based 2D materials in the realm of electronic devices.

Mannosylerythritol lipids (MELs), one of the most promising biosurfactants (BS), are glycolipids produced by yeasts or fungi, with great environmental performance and a high compatibility with the human body. MELs besides working as typical surfactants, can form diverse structures when in the critical aggregation concentration (CAC), reducing the surface tension of water and other solutions, and being stable over a wide range of conditions. Among others, MELs present anti-microbial, antitumor, antioxidant and anti-inflammatory activity, skin and hair repair capacity, which opens possibilities for their use in applications from cosmetics and pharmaceutics to bio-remediation and agriculture. However, their market share is still low when compared to other glycolipids, due to their less developed production process and higher production cost. This re-view gathers information on the potential applications of MELs mentioned on the literature since 1993. Furthermore, it is also explored the current strategies being developed to enhance the market presence of MELs, in parallel with the ones developed for rhamnolipids and sophorolipids.

In recent years, cerium dioxide (CeO2) has attracted considerable attention owing to its remarkable performance in various applications, including photocatalysis, fuel cells, and catalysis. This study explores the effect of nickel (Ni) doping on the structural, thermal, and chemical properties of CeO2 nanorods, particularly focusing on oxygen vacancy-related phenomena. Utilizing X-ray powder diffraction (XRD), alterations in crystal structure and peak shifts were observed, indicating successful Ni doping and the formation of Ni2O3 at higher doping levels, likely due to non-equilibrium reactions. Thermal gravimetric analysis (TGA) revealed changes in oxygen release mechanisms, with increasing Ni doping resulting in the release of lattice oxygen at lower temperatures. Raman spectroscopy corroborated these findings by identifying characteristic peaks associated with oxygen vacancies, facilitating the assessment of Ni doping levels. Overall, this study underscores the substantial impact of Ni doping on CeO2 nanorods, shedding light on tailored catalytic applications through modulation of oxygen vacancies while preserving the nanorod morphology.

Microwave technology has a potential application in the extraction of zinc from sulphide ores, knowledge of the dielectric properties of these ores plays a major role in the microwave design and simulation for any process. The dielectric properties of zinc sulfide concentrate for two different apparent densities—1.54 and 1.63 g/cm³—have been measured by using the resonance cavity perturbation technique at 915 and 2450 MHz during the roasting process for the temperature ranging from room temperature to 850 °C. The variations of dielectric constant, the dielectric loss factor, the dielectric loss tangent and the penetration depth with the temperature, frequency and apparent density have been investigated numerically. The results indicate that the dielectric constant increases as the temperature increases and temperature has a pivotal effect on the dielectric constant, while the dielectric loss factor has a complicated change and all of the temperature, frequency and apparent density have a significant impact to dielectric loss factor. Zinc sulfide concentrate is high loss material from 450 to 800 °C on the basis of theoretical analyses of dielectric loss tangent and penetration depth, its ability of absorbing microwave energy would be enhanced by increasing the apparent density as well. The experimental results also have proved that zinc sulfide concentrate is easy to be heated by microwave energy from 450 to 800 °C. In addition, the experimental date of dielectric constant and loss factor can be fitted perfectly by Boltzmann model and Gauss model, respectively.

As a member of smart materials, electrorheological elastomers (EREs) formed by pre-treating active electrorheological particles are attracting more and more attention. In this work, four Mg-doped strontium titanate particles with spherical, dendritic, flake-like and pinecone-like morphorlogies were obtained by hydrothermal and low-temperature co-precipitation. XRD, SEM, Raman and FT-IR were used to characterize the obtained products. The results showed that the sizes of Mg-doped strontium titanates are about 1.5‒2.0 μm, and the phase structure are dominated by cubic crystal. These Mg-doped strontium titanates were dispersed in a hydrogel composite elastic medium. Then, Mg-doped strontium titanate/glycerol/gelatin electrorheological composite hydrophilic elastomers were obtained with or without electric field. The electric field response properties of Mg-doped strontium titanate composite elastomers were investigated. It concluded that dendritic Mg-doped strontium titanate composite elastomers is high-performance EREs. And the maximum value of energy storage modulus of Mg-doped strontium titanate composite elastomers has achieved 8.70 MPa. This high electrorheological performance of the products is helpful for their applications in vibration control, force transducers, smart structures, dampers, and other fields.

The utilization of natural waxes to form oleogels has emerged as a new and efficient technique for structuring liquid edible oil into solid-like structures for diverse food applications. The objective of this study was to investigate the interaction between sunflower wax (SW) and monoglycerides (MGs) in olive oil oleogels and to assess their physical characteristics and storage stability. To achieve this, pure SW and a combination of SW with MGs in a 1:1 ratio were examined within a total concentration range of 6-12% w/w. The formed oleogels were characterized based on their microstructure, melting and crystallization properties, textural characteristics, and oxidative stability during storage. All the oleogels were shelf-stable, and as the concentration increased, the hardness of the oleogels also increased. The crystals of SW oleogels were long needle-like, while the combination of SW and MGs led to the formation of crystal aggregates and rosette-like crystals. The differential scanning calorimetry and FTIR showed that the addition of MGs led to different crystal structures. The oxidation results revealed that oleogels had low peroxide and TBARS values throughout the 28-day storage. These results provide useful insights about the utilization of SW and MGs oleogels for potential applications in the food industry.

We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

In this study, nanostructured cerium-doped TiO2 (Ce-TiO2) films with the addition of different amounts of cerium (0.00, 0.08, 0.40, 0.80, 2.40, and 4.10 wt. %) were deposited on a borosilicate glass substrate, by flow coating sol-gel process. After flow coating, deposited films were dried at the temperature of 100 °C for 1 h, followed by calcination at the temperature of 450 °C for 2 h. For the characterization of sol-gel TiO2 films, the following analytic techniques were used: X-ray diffraction (XRD), thermal gravimetry (TG), differential thermal analysis (DTA), and differential scanning calorimetry (DSC). Sol-gel derived Ce-TiO2 films were used for photocatalytic degrada-tion of the ciprofloxacin (CIP). The influence of the amount of Ce in TiO2 films, the duration of the photocatalytic decomposition, and the irradiation type (UV-A and simulated solar light) on the CIP degradation were monitored. Kinetics parameters (reaction kinetics constants and the half-life) of the CIP degradation, as well as photocatalytic degradation efficiency, were determined. The best photocatalytic activity was achieved by the TiO2 film doped with 0.08 wt.% Ce, under both UV-A, and solar irradiation.

Plant cells' ability to withstand abiotic stress is strongly linked to modifications in their mechanical characteristics. Nevertheless, the lack of a workable method for consistently tracking plant cell mechanical properties severely restricts our comprehension of the mechanical alterations in plant cells under stress. With Polyethylene Glycol (PEG6000), we created a drought-like environment, and we used the Double Resonator Piezoelectric Cytometry (DRPC) method to dynamically and non-invasively track changes in the stress (ΔS) created and viscoelasticity (storage modulus G' and loss modulus G") of protoplasts and suspension cells of rice during drought stress. The findings demonstrate that, rice suspension cells and protoplasts react mechanically differently to 5%–15% PEG6000 stress, implying distinct resistance mechanisms. However, neither of them can withstand 25% PEG6000 stress, they respond mechanically similarly to 25% PEG6000 stress. The results of DRPC are further corroborated by the morphological alterations of rice cells and protoplasts observed under an optical microscope. To sum up, the DRPC technique functions as a precise cellular mechanical sensor and offers novel research tools for the evaluation of plant cell adversity and differentiating between the mechanical reactions of cells and protoplasts under abiotic stress.

Negative temperature coefficient (NTC) materials are usually based on ceramic semiconductors and electrons are involved in their transport mechanism. A new type of NTC material, adequate for alternating current (AC) applications, is represented by zeolites. Indeed, zeolites are single-charge carrier ionic conductors with a temperature-dependent electrical conductivity. In particular, electrical transport in zeolites is due to the monovalent charge-balancing cations, like K⁺, capable of hopping between negatively charged sites in the aluminosilicate framework. Owing to the highly non-linear electrical behavior of the traditional electronic NTC materials, the possibility to have alternative types of materials, showing linearity in the electrical behavior, is very desirable. Among different zeolites, the natural clinoptilolite has been selected for investigating the NTC behavior since it is characterized by high zeolite content, convenient Si/Al atomic ratio, good mechanical strength, due to its compact microstructure, and low toxicity. Clinoptilolite has shown a rapid and quite reversible impedance change under heating, characterized by a linear dependence on temperature. X-ray diffraction (XRD) has been used to identify the natural zeolite, to establish all types of crystalline phases present in the mineral, and to investigate the thermal stability of these phases up to 150°C. X-ray photoelectron spectroscopy (XPS) analysis has been used for the chemical characterization of the natural clinoptilolite sample, providing important information on the cationic content and framework composition. In addition, since electrical transport takes place in the zeolite free-volume, a Brunauer–Emmett–Teller (BET) analysis of the mineral has been also performed.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

Improvement of hydrophysical properties and corrosion resistance of self-compacting concrete to the effects of alternate freezing-thawing and aggressive soils of southern and central Kazakhstan is of interest to a wide range of researchers from the side of practical application of the obtained results in construction practice. It is proposed to form a spatially reinforced fine crystalline structure of cement matrix with maximum dense packing by using a complex modifier (Hyperplasticiser + Polymer + Microsilica + Fibro fibers) in the composition of self-compacting concretes (SCC). The introduction of the calculated amount of the above additives increases the operational reliability of the current SCC compositions, increasing the water resistance to W16, frost resistance to F=500, increasing the compressive strength by 20%, reducing the mass loss of samples during corrosion leaching to 50%. It has been experimentally established that the proposed addition of complex modifier (Hyperplasticiser + Polymer + Microsilica + Fiber fibers) to the SCC composition allows obtaining self-compacting concrete of high quality with improved performance characteristics (compressive strength, water resistance, frost resistance and corrosion resistance). Studies have shown that the complex modifier-modified SCC compositions have a high degree of resistance in aggressive environments and leaching corrosion. Based on the results of the conducted tests, it is possible to recommend the obtained SCC compositions for production of building products working in the zone of alternating freezing-thawing and aggressive soils.

The influence of short term water absorption on the mechanical properties of halloysite nanotubes-multi layer graphene reinforced polyester hybrid nanocomposites has been investigated. The addition of nano-fillers significantly increased the flexural strength; tensile strength and impact strength in dry and wet conditions. After short term water exposure; the maximum microhardness; tensile; flexural and impact toughness values were observed at 0.1 wt% MLG. The microhardness increased up to 50.3%; tensile strength increased up to 40% and flexural strength increased up to 44%. Compared to dry samples; the fracture toughness and surface roughness of all types of produced nanocomposites were increased that may be attributed to plasticization effect. Scanning electron microscopy revealed that the main failure mechanism is caused by the weakening of nano-filler-matrix interface induced by water absorption. It was further observed that synergistic effects were not effective at concentration of 0.1 wt% to produce considerable improvement in mechanical properties of produced hybrid nanocomposites.

This study presents PlanteSaine, a novel mobile application powered by Artificial Intelligence (AI) models explicitly designed for maize, tomato, and onion farmers in Burkina Faso. Agriculture in Burkina Faso, like many developing nations, faces substantial challenges from plant pests and diseases, posing threats to both food security and economic stability. PlanteSaine addresses these challenges by offering a comprehensive solution that provides farmers with real-time identification of pests and diseases. Farmers capture images of affected plants with their smartphones, and PlanteSaine's AI system analyzes these images to provide accurate diagnoses. The application's offline functionality ensures accessibility even in remote areas with limited internet connectivity, while its messaging feature facilitates communication with agricultural authorities for guidance and support. Additionally, PlanteSaine includes an emergency alert mechanism to notify farmers about pest and disease outbreaks, enhancing their preparedness to deal with these threats. An AI-driven framework, featuring an image feature extraction phase with EfficientNetB3 and an artificial neural network (ANN) classifier, was developed and integrated into PlanteSaine. The evaluation of PlanteSaine demonstrates its superior performance compared to baseline models, showcasing its effectiveness in accurately detecting diseases and pests across maize, tomato, and onion crops. Overall, this study highlights the potential of PlanteSaine to revolutionize agricultural technology in Burkina Faso and beyond. Leveraging AI and mobile computing, PlanteSaine provides farmers with accessible and reliable pest and disease management tools, ultimately contributing to sustainable farming practices and enhancing food security. The success of PlanteSaine underscores the importance of interdisciplinary approaches in addressing pressing challenges in global agriculture

The increased consumption of food requiring thermoformed packaging means that the packaging industry demands customized solutions in terms of shapes and sizes to make the packaging unique. In particular, the food industry increasingly requires more transparent packaging, with greater clarity and a better presentation of the product features they contain. However, in turn, the differentiation of products is sought through the geometry and final finish of the product, as well as the arrangement of food inside the packaging. In addition, these types of packaging usually include ribs in the walls to improve physical properties, however they also affect the final aesthetics of the product. In accordance with this, this research study analyses by studying the mechanical properties of different relief geometries that can affect not only the aesthetics but also their strength. For this purpose, tensile and compression tests have been carried out. The results provide comparative data on the reliefs studied and show that there are different shapes, sizes and layout.

The study findings revealed significant variability in various wood properties among different genetic families, although the static modulus of elasticity did not exhibit significant differences between the chosen genetic families. All measured wood properties decreased from the bottom to the top of the model trees. Wood hardness displayed a moderately negative correlation with wood density and weak correlations with MOE and MOR. Given the weak correlations between wood hardness and other wood mechanical properties, it is suggested that the MOEdyn would be a more suitable trait for genetic studies.

In recent decades, the requirements for implantable medical devices increased, but the risks of implant rejection still exist. These issues are primarily associated with poor osseointegration, leading to biofilm formation on the implant surface. This study focuses on addressing these issues by developing a biomaterial for implant coatings. 45S5 Bioglass has been widely used in tissue engineering due to its ability to form a hydroxyapatite layer, ensuring a strong bond between the hard tissue and the bioglass. In this context, 45S5 bioglasses, modified by the incorporation of different amounts of copper oxide, from 0 to 8 mol%, were synthesized by the melt-quenching technique. The incorporation of Cu ions does not show a significant change in the glass structure. Since the bioglass exhibited the capacity of being polarized, and therefore promoting the osseointegration effectiveness, the electrical properties of the prepared samples were studied using the impedance spectroscopy method, in the frequency range of 102-106 Hz and temperature range of 200-400 K. The effects of CuO on charge transport mobility were investigated. Additionally, the bioactivity of the modified bioglasses was evaluated through immersion tests in simulated body fluid. The results revealed the initiation of a Ca-P-rich layer formation on the surface within 24 h, indicating the potential of the bioglasses to enhance the bone regeneration process.

The advancement in science and technology has led to luffa sponge (LS) being widely used as a natural material in industrial application as its polyporous structure and light texture. In order to enhance the utility of LS fibers as the reinforcement of lightweight composite materials, this study investigate its water absorption, mechanical properties, anatomical characteristic and thermal performance. Hence, moisture regain, tensile properties of LS fiber bundles were measured in accordance with standards and the structural characteristics were investigated via microscopic observation. Scanning electron microscopy (SEM) was used to observe the surface morphology and fracture surface of fiber bundles. Test results shows that the special structure where the phloem tissues degenerate to cavities had a significant influence on the mechanical properties of LS fiber bundles. Additionally, the transverse sectional area occupied by fibers in a fiber bundle (SF), wall thickness and ratio of wall to lumen of fiber cell, and crystallinity of cellulose had an impact on the mechanical properties of LS fiber bundles. Furthermore, the fiber bundles density of LS varies range of 385.46-468.70 kg/m³, much less than that of jute (1360.40 kg/m³) and Arenga engleri (950.20 kg/m³) while LS fiber bundles has superior specific modulus.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

This study investigates the effects of Zinc (4wt.%) and severe plastic deformation on the mechanical properties of AZ61 magnesium alloy through the stir-casting process. The severe plastic deformation (equal channel angular pressing (ECAP)) has been done followed by T4 heat treatment. The microstructural examinations revealed that the addition of 4wt.%Zn enhances the uniform distribution of β-phase, contributing to a more uniformly corroded surface in corrosive environments. Additionally, dynamic recrystallization (DRX) significantly reduces the grain size of as-cast alloys after undergoing ECAP. The attained mechanical properties demonstrate that after a single ECAP pass, AZ61 + 4wt.%Zn alloy exhibits optimal yield strength (YS), ultimate compression strength (UCS), and hardness. This research highlights the promising potential of AZ61 + 4wt.%Zn alloy for enhanced mechanical and corrosion-resistant properties, offering valuable insights for applications in diverse engineering fields.

It is of great academic significance to understand how the atomic structure of interfaces and boundaries in materials impacts the magnetic coupling nature across the boundaries and encourage development of state-of-the-art magnetic devices. Here, we carry out a systematic investigation of the atomic and electronic structures of twin boundaries (TBs) in LiFe5O8 thin films and determine their concurrent magnetic couplings using atomic-resolution transmission electron microscopy and atomistic first-principles calculations. The results show ferromagnetic or antiferromagnetic coupling can exist across the different TBs in LiFe5O8 (LFO) thin films and electrical structures within a few atomic layers directly rely on the TB atomic core structures. Uncovering one-to-one relationship between the magnetic properties of individual TB and the local atomic structures will clarify a thorough comprehension of numerous fascinating magnetic properties of commonly utilized magnetic materials, which will undoubtedly encourage the progress of sophisticated magnetic materials and devices.

The rock joint fissure slope in cold regions is prone to deformation and failure problems such as relaxation, tension and collapse under freeze-thaw (F-T) cycles. Based on the ideology of clean production and promoting the structural integrity of geotechnical projects in cold areas, this study designed and prepared aeolian-sand (AS) to replace part of river sand as a filling mortar material by taking advantage of the low cost and easy availability of AS. Investigations were carried out to determine the impact of varying proportions of AS in mortar on the microstructure and shear properties of the mortar-rock interface under F-T cycles. Therefore, F-T cycle testing, nuclear magnetic resonance (NMR) testing and shear testing were carried out on grout with different proportions of AS. The results show that the right proportion of AS replacement could enhance the shear deformation resistance and F-T resistance of the mortar-rock interface, and 30% proportion is the optimal proportion. By increasing of F-T cycles, the three types of specimens showed different degrees of particle spalling, shedding and cracking. The slurry-rock interface layer in the A (0%) group exhibited the most severe F-T deterioration, while the B (15%) group showed a lesser degree, and the C (30%) group performed the best. T2 spectrum curve and total spectrum area change law from the microscopic point of view to verify the 30% AS proportion mortar-rock interface F-T resistance is the strongest, followed by 15% AS proportion mortar, the weakest is ordinary mortar. The degradation of the mortar-rock bond is primarily due to the conversion of solid to liquid phases and the movement of internal water caused by fluctuating temperatures. The extent of F-T deterioration in the slurry-rock interface layer is greatly affected by the varying proportions of AS. The shear strength and shear stiffness of specific proportion of AS decreased with the increase of F-T cycles. For same F-T cycles, the shear strength and shear stiffness of group C (30%) were the highest, followed by group B (15%) and group A (0%). The grout material not only reinforces the F-T joint fissure slope, but also reduces the cost of grout reinforcement and promotes the clean production of geotechnical structures.

Yttria stabilized zirconia materials are frequently used in mechanical engineering and biomedical applications. Demanding loading conditions require materials combining a high level of strength and fracture toughness. A ready to press alumina doped 2 mol% yttria stabilized zirconia powder was shaped by axial pressing and sintering in air at 1250 - 1500 °C for 2 h. The best combination of strength and toughness value of 7.8 MPa√m. Materials sintered in the middle of the chosen temperature range combine fully density, high transformability and small grain size. Toughness measurements by direct crack length measurements delivered unrealistically high fracture toughness values.

The field of construction materials is pivotal in developing sustainable and resilient infrastructure. This demands continuous research to understand the properties and behaviors of these materials under diverse conditions. Although advancements in material science and numerical modeling have been significant, experimental testing remains indispensable for a thorough comprehension of material characteristics, particularly under extreme stresses and environmental factors. This need has forced the development of a wide array of testing techniques, each designed to evaluate specific engineering properties, thus creating a complex and varied landscape of experimental methodologies. This study provides a comprehensive overview of both conventional and innovative experimental testing techniques used to characterize construction materials. It explores the related methodologies and identifies potential gaps in their application within the industry. The spectrum of testing covered includes mechanical, chemical, thermal, microstructural, durability, physical, rheological properties, and non-destructive testing methods. Mechanical tests assess strength, hardness, and fatigue, whereas chemical analyses utilize techniques such as spectroscopy and chromatography. Thermal properties are examined using thermogravimetric analysis, and microstructural characteristics are explored through advanced imaging techniques. Durability testing focuses on materials’ resistance to environmental challenges, while physical properties tests evaluate aspects like porosity and water absorption. Rheological and non-destructive tests further examine materials’ behavior and integrity without causing damage. By discussing these methodologies, the study sheds light on various approaches to material evaluation and aims to enhance the selection, application, and development of testing standards. This overview seeks to inform and inspire future research and innovation in the science of construction materials, contributing to the development of more resilient and sustainable construction practices.

Terrestrial orchid tubers are an important source of food in some parts of Africa and are traditionally included in the diets of most rural communities in Malawi. However, there is limited information on the nutritional and phytochemical content of the Malawian orchids to substantiate their traditional use. The present study evaluates the nutritional and phytochemical variation of four orchid species: Disa zombica, Satyrium buchananii, Satyrium carsonii, and Satyrium trinerve, collected from the same ecological zone of Malawi. The proximate content, minerals, phytochemicals, and functional properties were analysed using official procedures. Protein ranged from 2.19% to 4.65%, whereas carbohydrate ranged from 65.24% to 80.22%, with S. carsonii and S. trinerve registering the highest protein and carbohydrate contents, respectively. Iron and potassium were highest in D. zombica, while sodium and calcium were highest in S. buchananii. The total phenolics ranged from 228.56 to 500.00 mg GAE/100 g, with D. zombica registering the highest. The water absorption capacity ranged from 4.10 to 10.88 g/g. Albeit variable levels, the study provides evidence that orchid species contain essential nutrients and phytochemicals important for human nutrition and health. Furthermore, the functional properties can be utilised in the development of food products, such as baked products.

Hazelnuts are one of the most valuable nuts in the world due to their unique organoleptic properties and nutritional characteristics. This work was intended to analyze some physical and chemical properties of various hazelnut cultivars grown in Zakataly (Azerbaijan), namely Ata-baba, Elbari, Topqara, Firovan, Nasimi, Qalib, Mirzebeyli, Tala, Dash findiq, Barli, Azeri and Sachaqli. In general, the results showed statistically significant differences between the studied cultivars. The density of kernels, depending on the hazelnut cultivars, varied from 0.71 g/cm³ (Azeri) up to 1. 03 g/sm³ (Sachaqli). The peeled fruits of Dash findiq were heavier on average (1.64±0.34 g), and the peeled fruits of Nasimi, Qalib, Mirzebeyli and Sachaqli were lighter on average (0.8±0.23 g, 0.8±0.31 g, 0.8±0.20 g and 0.80±0.09 g, respectively. In the unpeeled form, Dash findiq nuts were the heaviest (3.70±0.34 g), and Nasimi and Qalib nuts were the lightest of all cultivars (2.0 ±0.48 g and 2.0 ±0.36 g, respectively). Ata-baba nuts account for 49 masses per kernel. %, in other studied cultivars - 33.3- 45.3 wt. %. Nasimi nuts are rounded (in the equatorial zone); Tala, Ata-baba, Firovan and Azeri - rounded-oblong; Topqara, Barli and Dash findiq – oblong; Elbari, Qalib, Mirzebeyli and Sachaqli - elongated. Firovan, Tala and Topqara have thicker shells. Ata-baba is significantly ahead of other varieties in the yield of kernels (490 kg / 1 ton of nuts), Tala is in second place in this indicator (453 kg / 1 ton of nuts), Topqara is in third (433 kg/ 1 ton of nuts). According to the maximum fat content, the cultivars Mirzebeyli (77.00±2.20 g/100 g of kernels) and Firovan (75.0±3.08 u/100 kernels), protein - Sachaqli (16.02±0.50 u/100 kernels) and Ata-baba (15.92±0.48 g/100 g of kernels) were distinguished. The results of this study help to better understand the differences between some varieties of hazelnuts grown in Azerbaijan, which provides important clues for all players involved in this sector.

The Energy Performance of Buildings Directive 2010 calls for the Nearly Zero Energy Standard for new buildings from 2021 onwards: Buildings using “almost no energy” are powered by renewable sources or energy produced by the building itself. For residential buildings, this ambitious new standard has already been reached. But for other building types this goal is still far away. The potential of these buildings to meet a Nearly Zero Energy Standard was investigated by analyzing ten case studies representing non-residential buildings with different uses. The analysis shows that the primary characteristics common to critical building types are a dense building context with a very high degree of technical installation (such as hospital, research and laboratory buildings). The large primary energy demand of these types of buildings cannot be compensated by building and property-related energy generation including off-site renewables. If the future Nearly Zero Energy Standard were to be defined with lower requirements because of this, the state related properties of Bavaria suggest that the real potential energy savings available in at least 85% of all new buildings would be insufficiently exploited. Therefore, it would be useful to instead individualize the legal energy verification process for new buildings to distinguish critical building types such as laboratories and hospitals.

The article presents the results of research work devoted to the study of composite materials on polymer binder with the content of modified mineral filler - water-dispersion paint and varnish materials on acrylic polymer with modified filler - diatomite. The aim of the study is to obtain polymer-based composites with modified diatomite (water-dispersion paint on acrylic binder) with improved performance properties. Methods: determination of porosity, adhesion, elasticity, hiding power of the control composition; determination of porosity, adhesion, elasticity, hiding power of the obtained composites with the use of modified filler; investigation of the influence of radiation in the infrared radiation (IR) region of the spectrum of the paint coating surface using FLIRB620 thermal imager. As a result of work it is noticed that modification of water dispersions by silica activated diatomite promotes elimination of the main disadvantages of materials and coatings on the basis of acrylate binder - low water resistance and low physical and mechanical characteristics, introduction of modified diatomite into water emulsion paint on acrylate basis does not lead to deterioration of the main operational characteristics of paint and varnish coatings - porosity, adhesion, elasticity and covering. When analyzing the effect of emissivity in the IR region of the spectrum of the paint coating surface, a significant effect of the quantitative content of modified diatomite on the reduction of emissivity of paint coatings in the IR region of the spectrum was established and it was shown that a significant effect of the reduction of emissivity of paint coatings in the IR region of the spectrum is provided by the introduction of modified diatomite in the amount of 40 wt.h. into the mixture. The influence of the time of full-scale tests in the investigated small range regardless of the quantitative composition of modified diatomite on the performance characteristics of the paintwork was established.

In this study we have investigated the effect of the addition of Nb2O5 (up to 5 mol%) on the structure and luminescent properties of ZnO-B2O3 glass doped with 0.5 mol % Eu2O3 by using of infrared (IR), Raman and photoluminescence (PL) spectroscopy. Physical properties as molar volume, oxygen packing density and glass transition temperature were determined using the results of differential thermal analyisis (DTA) and Archimedes principle for density. IR and Raman spectra revealed that niobium ions incorporate into the base zinc borate glass as NbO4 trtraherda and NbO6 octahedra. A strong red emission from the 5D0 level of Eu3+ ions was registered under near UV (392 nm) excitation using the sharp 7F0 - 5L6 transition of Eu3+. The integrated fluorescence intensity ratio R (5D0 → 7F2/5D0 → 7F1) was calculated to estimate the degree of asymmetry around the active ion, suggesting a location of Eu3+ in non-centrosymmetric sites. The higher Еu3+ luminescence emission observed in zinc borate glasses containing 1÷5 mol% Nb2O5 compared to the Nb2O5-free zinc borate glass evidences that Nb2O5 is suitable component for modification of host glass structure and improving the emission intensity.

Abstract. Results of research into four-membered phosphorus(V)-heterocycles, 2-halogen-1,2λ⁵-oxaphosphetanes are presented. The preparation of 2-halo-1,2λ⁵-oxaphosphetanes by reaction of P-haloylides with carbonyl compounds is described. The mechanism of asynchronous [2+2]-сycloaddition of ylides to aldehydes was proposed on the base of low-temperature NMR investigations. 2-Halogen-1,2λ⁵-oxaphosphetanes were isolated as individual compounds and their structures were confirmed by ¹Н, ¹³C, ¹⁹F and ³¹Р NMR spectra. These compounds are convenient reagents for preparing of various organic and organophosphorus compounds hardly available by other methods. Chemical and physical properties of the 2-halo-1,2λ⁵-oxaphosphetanes are reviewed. The 2-chloro-1,2λ⁵-oxaphosphetanes depending on substituents at the α-carbon atom rearrange with formation of 2-chloroalkylphosphonates or convert into trans-phosphorylated alkenes. Prospective synthetic applications of 2-halo-1,2λ⁵-oxaphosphetanes are analyzed. The 2-halo-1,2λ⁵-oxaphosphetanes may be easily converted to various alkenylphosphonates: allyl- or vinylphosphonates, phosphorus ketenes, thioketenes, ketenimines.

The targeted compounds in this research, resveratrol analogs 1–14 were synthesized as mixtures of isomers by the Wittig reaction using heterocyclic triphenylphosphonium salts and various benzaldehydes. The planned compounds were those possessing the trans-configuration as the biologically active trans-resveratrol. The pure isomers were obtained by repeated column chromatography in various isolated yields depending on the heteroaromatic ring. It was found that butyrylcholinesterase (BChE) was more sensitive to the heteroaromatic resveratrol analogs than acetylcholinesterase (AChE), except for 6, the methylated thiophene derivative with chlorine, which showed equal inhibition toward both enzymes. Compounds 5 and 8 achieved the highest BChE inhibition with IC50 values of 22.9 and 24.8 μM, respectively. The same as with AChE and BChE, methylated thiophene subunits of resveratrol analogs showed better enzyme inhibition than unmethylated ones. Two antioxidant spectrophotometric methods, DPPH and CUPRAC, were applied to determine the antioxidant potential of new heteroaromatic resveratrol analogs. Molecular docking of these compounds was conducted to visualize the ligand-active site complexes' structure and identify the non-covalent interactions responsible for the complex's stability, which influence the inhibitory potential. As ADME properties are crucial in developing drug product formulations, they have also been addressed in this work. The potential genotoxicity is evaluated by in silico studies for all compounds synthesized.

In this paper glass crystallization behavior of 50ZnO:47B2O3:3Nb2O3:0.5Eu2O3 (G-0h) glass has been investigated in detail by DSC, XRD and TEM analysis. The luminescent properties of resulted glass-ceramics were also investigated. By XRD and TEM analysis crystallization of several crystalline phases have been proved (α-Zn3B2O6, β-Zn3B2O6 and ZnNb2O6). By calculating of crystal parameters it was found that europium ions are successfully incorporated in the β-Zn3B2O6. Photo-luminescent spectra show an increased emission in the resulting glass-ceramic samples as compared with the parent glass sample because of the higher asymmetry of Eu3+ ions in the crystalline phases obtained. It was established that the optimum emission intensity is registered for glass-ceramic sample obtained after 25 hours heat treatment of the parent glass.

Chitosan (CS) nanoparticles are under investigation for a wide range of applications in nanomedicine. The structural, molecular and physicochemical properties of chitosan nanoparticles have a direct bearing on their efficacy in drug conjugation and delivery, gene delivery, and tissue engineering. Herein we report on the structural, morphological and molecular properties of chitosan nanoparticles synthesized using the ionic gelation method with the intended purpose of being used for drug delivery. The chitosan nanoparticles (CS-NPs) were prepared in the 0.25 to 1.0% w/v concentration range, whereas separate samples of the 1.0% w/v CS-NPs were also functionalized with polyethylene oxide (PEO) alone and with a diblock copolymer of PEO and polypropylene glycol (PPG). The average size of the CS-NPs was determined from TEM imaging to be in the range of 11.3 to 14.8 nm. The XRD and TEM analyses show that the CS-NPs have semi-crystalline structure with the degree of crystallinity depending upon the nature of synthesis. Our results show that functionalizing the 1.0% w/v CS-NPs with PEO increases the degree of crystallinity whereas functionalizing with the diblock copolymer PEO - PPG results in a significant increase in their degree crystallinity. The CS/TPP concentration (CS:TPP fixed at 1:1 ratio) had no apparent effect on the degree of crystallinity of the CS-NPs. The results from the FTIR analysis confirm incorporation of TPP with CS in the CS-NPs. Additionally, FTIR analysis shows an enhancement of hydrogen bonding that is consistent with the increase in the degree of crystallinity of the CS-NPs.

This article explores the cutting-edge advancement of gypsum and cement building boards infused with shape-stabilized n-octadecane, an organic phase change material (PCM). The primary focus is on improving energy efficiency and providing electromagnetic interference (EMI) shielding capabilities for contemporary buildings. The research investigates the integration of these materials into construction materials, using red-mud Carbon Foam as a stabilizer for n-octadecane (OD@CCF). Various analyses, including microstructural examination, porosity assessment, and additive dispersion, were conducted using X-ray microtomography and density measurements. Thermal conductivity measurements demonstrated the enhancement of composite boards as the OD@CCF content increased, while mechanical tests indicated an optimal additive content of up to 20%. The thermal-regulated capabilities of these advanced panels were evaluated in a custom-designed room model equipped with a homemade environmental chamber, illustrating a consistent temperature environment during heating and cooling cycles. The incorporation of OD@CCF into cement boards exhibited improved thermal energy storage properties. Moreover, the examined composite boards displayed efficient electromagnetic shielding performance within the frequency range of 3.2–7.0 GHz, achieving EMI values of approximately 18 and 19.5 dB for gypsum and cement boards, respectively, meeting the entry-level value required for commercial applications.

In the present study, a multilayer high barrier thin blown film based on a polybutylene adipate terephthalate (PBAT) blend with polyhydroxyalkanoate (PHA), and composed of four layers, including a cellulose nanocrystals (CNC) barrier layer and an electrospun poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) hot-tack layer, was characterized in terms of surface roughness, surface tension, migration, mechanical and peel performance, barrier properties and disintegration rate. The results showed a material with a smooth surface. The overall migration test showed that the material was suitable for its use as a food contact layer. The addition of the CNC interlayer had a significant effect on the mechanical properties of the system, drastically reducing the elongation at break and, thus, the flexibility of the material. However, the material retained its elastic modulus and tensile strength. The CNC coating had a negative impact on the peeling strength, weakening the inherently strong interlayer adhesivity of the electrospun PHBV fibers. The multilayer had a good barrier to water vapor, and especially to oxygen, with its permeance reduced by up to a 90 % when the CNC layer was present. Finally, the monolayer blend film disintegrated in a period of less than 55 days in a laboratory-scale composting experiment, while the multilayer system disintegrated in 60 days. Overall, the multilayer system formed a fully compostable structure with great potential for use in food packaging applications.

Sesamum indicum is considered an underutilized oil-bearing seed in the semi-arid regions of Ghana. Nonetheless, it is a promising source of food with both nutritional and therapeutic benefits. The aim of the present study was to evaluate the antioxidant properties S. indicum seeds using different extraction solvents. The seeds were obtained from the local farmers and prepared for analysis. The bioactive compounds present in the seeds were extracted using hexane, ethyl acetate, ethanol and water and their yields quantified. Total phenolic content (TPC), Condensed tannin content (TTC) and Total antioxidant capacity (TAC) , and DPPH radical scaveging assay were analyzed using standard methods. Antinutrients such as saponins, alkaloids, phytates and oxalates were also analyzed from the powdered seeds. Two chemometric methods; hierarchical cluster analysis (HCA) and Pearson correlation were employed to evaluate the interdependence of the various parameters to result in their antioxidant properties. The re-sults revealed that the solvents utilized had a significant impact on the extraction yield, phyto-chemical component concentration, and antioxidant activities. Hexane extracts of S. indicum seeds significantly exhibited the highest antioxidant activity (p < 0.05). It was marked with the highest TAC value of 232.6 ± 6.267 mg/g AAE and a strong DPPH scavenging activity with an IC50 of 52.81 ± 2.30 µg/mL. Correlations (p < 0.05) was established between TPC,CTC, TAC and DPPH radical scavenging activity) of the extracts. Antinutrients such as; phytate, oxalate, saponins and alkaloids were found to be 7.691 ± 0.8576, 1.501 ± 0.1375, 21.33 ± 4.619 and 317.33 ± 30.29 mg/g respectively. Data obtained suggest that S. indicum possess rich bioactive compounds that can be used in neutraceuticals and food products.

The microbial contamination in food packaging have been a major concern that paved the way for the search for natural based new anti-microbial agents, such as modified α-mangostin. In the present work, twelve synthetic analogs were obtained via semi-synthetic modification of α-mangostin by Ritter reaction, reduction by palladium-carbon (Pd-C), alkylation, and acetylation. The evaluation of the anti-microbial potential of the synthetic analogs showed higher therapeutic value than the parent molecule. The anti-microbial studies proved that I E showed higher antibacterial activity whereas I I showed most significant antifungal activity. Due to their microbial properties, modified α-mangostin can be utilized as active anti-microbial agents in food packaging.

This study utilises NaOH to treat composite cementitious materials containing aeolian sand and zeolite powders, which were used to replace 50% of the cement in aeolian-sand concrete (ASC). The mechanical properties of treated ASC considerably improved, especially when the NaOH dosage was 4% by mass. After curing this sample (denoted as AAZC-4) for 28 d, its compressive strength improved by 17.2% and its split tensile was increased by 16.3%. Potassium feldspar and montmorillonite in zeolite powder and SiO2 in the sand were decomposed by OH− and combined with other elements to generate various silicate gels and A-type potassium zeolite crystals inside the concrete. Microscopic examination showed that the gels and crystals intertwined to fill the pores, decreasing (increasing) the percentage of large (small) pores, thus optimising the pore structure. This substantially improved the mechanical properties of ASC. Freeze–thaw salt-intrusion tests showed that the extent of mass loss, degree of damage and loss of compressive strength of AAZC-4 were similar to those of ordinary concrete but were reduced by 36.8%, 19% and 52.1%, respectively, compared with those of ASC. Therefore, AAZC-4 has sustainable working performance in the chloride ion permeable environment in cold and arid areas.

The carbonyl iron particles were dispersed in a polychloroprene rubber (CR) matrix under an external magnetic field for practical application as microwave absorption composites film. The film prepared under external magnetic field with a thickness of only 0.54 mm showed least reflection loss of -15.98 dB and the reflection loss value less than -10.0 dB over the frequency range of 11.4~14.8 GHz. In comparison with the microwave absorption properties of calculation by transmission line theory based on the tested relative complex permittivity and permeability and film prepared by general route without external magnetic field, the film made with external magnetic field exhibited more excellent microwave absorption properties, strongly depending on the increment of anisotropy and rearrangement of magnetic particles. The results indicated the composite film made under external magnetic field have excellent microwave absorption properties, which suggest that the composites thin film could be used as a thinner and lighter microwave absorber.

The accuracy of cosmic ray observation by the Large High Altitude Air Shower Observatory Wide Field-of-view Cherenkov/fluorescence Telescope Array (LHAASO-WFCTA) is influenced by variations in aerosols in the atmosphere. The solar photometer (CE318-T) is extensively utilized within the Aerosol Robotic Network as a highly precise and reliable instrument for aerosol measurements. With this CE318-T 23, 254 sets of valid data samples in 394 days from October 2020 to October 2022 at the LHAASO site were obtained. Data analysis revealed that the baseline Aerosol Optical Depth (AOD) and A˚ngstro¨m Exponent (AE) at 440-870 nm (AE440−870nm) of the aerosols were calculated to be 0.03 and 1.07, respectively, suggesting that the LHAASO site is among the most pristine regions on Earth. The seasonality of the mean AOD are the order of spring > summer > autumn = winter. The monthly average maximum of AOD440nm occurred in April (0.11 ± 0.05) and the minimum was in December (0.03 ± 0.01). The monthly average of AE440−870nm exhibited slight variations. The seasonal characterization of aerosol types indicated that clean continental background aerosol predominated in autumn and winter, which is the optimal period for the absolute calibration of the WFCTA. Additionally, the diurnal daytime variations of AOD and AE across the four seasons are presented. Our analysis also indicates that the potential origins of aerosol over the LHAASO in four seasons were different and the atmospheric aerosols with higher AOD probably originate mainly from Northern Myanmar and Northeast India region. These results provide a baseline for comparison to the future on-site measurement of extinction coefficient profile and aerosol phase function by LHAASO-WFCTA, also enrich the valuable materials on aerosol observation in the Hengduan Mountains and Tibetan Plateau.

Hierarchical tungsten oxide assemblies such as spindle-like, flowers with sharp petals, nanowires and regular hexagonal structures are successfully synthesized via a solvothermal reduction method by simply adjusting the reaction conditions. On the basis of the experimental results, it is determined that the reaction time significantly influences the phase transition, microstructure and photocatalytic activity of the prepared samples. The possible mechanisms for the phase transition and morphology evolution process have been systematically proposed. Moreover, the as-prepared products exhibit significant morphology-depended photocatalytic activity. The flower-like W18O49 prepared at 6 h possesses large specific surface area (150.1 m²g^-1), improved separation efficiency of electron-hole pairs and decreased electron-transfer resistance by the photoelectrochemical measurements. As a result, the flower-like W₁₈O₄₉ prepared at 6 h exhibits the highest photocatalytic activity for the degradation of Methyl orange aqueous solution. The radical trap experiments showed that the degradation of MO was driven mainly by the participation of h⁺ and •O²⁻ radicals.

The ability of thermoresponsive polymers to respond to temperature with a reversible conformational change makes them promising ‘smart’ materials for solutions in medical and biotechnological applications. In this work, two such polymers and structural isomers were studied: poly(N-isopropyl acrylamide) (PNiPAm) and poly(2-isopropyl-2-oxazoline) (PiPOx). We compare the critical solution temperatures (CST) of these polymers in D2O and H2O in the presence of Hofmeister series salts, as results obtained under these different solvent conditions are often compared. D2O has a higher dipole moment and electronegativity than H2O, which could significantly alter the CST transition. We used two complementary methods to measure the CST, dynamic light scattering (DLS) and differential scanning calorimetry (DSC), and found that the CST decreased significantly in D2O compared to H2O. In the presence of highly concentrated kosmotropes, the CST of both polymers decreased in both solvents. The influence of the kosmotropic anions was smaller than the water isotope effect at low ionic strengths but considerably higher at physiological ionic strengths. However, the Hofmeister anion effect was quantitatively different in H2O than in D2O, with the largest relative differences observed for Cl-, where the CSTs in D2O decreased more than in H2O measured by DLS but less by DSC. PiPOx was more sensitive than PNiPAm to the presence of chaotropes. It exhibited much higher transition enthalpies and multistep transitions, especially in aqueous solutions. Our results highlight that measurements of thermoresponsive polymer properties in D2O cannot be compared directly or quantitatively to application conditions or even measurements performed in H2O.

The present study drops the line for the flow characteristics of fly ash-based (FA) geopolymers reinforced with polypropylene (PP) fibers undergoing the extrusion process during three-dimensional printing. Applying to the Herschel-Bulkley rheological model the research is ready with the sound theoretical basis which is used to understand the flow behavior of these materials under various conditions. A combination of experimental and numerical techniques that are based on the Finite Element Method (FEM) in COMSOL has been used in this study. The results of both the experimental and simulation approaches are then compared and the behavior of the material during extrusion is then examined. The experimental results proved PP fiber content has significant effects on rheological properties. The experiments on mixes which are either devoid of fibers or possess a high content of fiber, encountered problems like a high static yield stress and material segregation. Mixes with fibers of moderate content showed smoother extrusion processes, which means that a suitable range of fiber addition exists for the fibers that optimally balance the mechanical properties and extrudability. Numerical simulations typically agreed with experimental data for fiber contents up until it reached a certain level but not above, suggesting the existence of more complex interactions inside the fibers and the necessity for the subsequent model refinements. The investigation outlines a 0.25% and 0.5% fiber content range that leads to enhanced performance without bringing the extrusion process to greater complications and further making the production of proper, architecturally printed structures possible.

In the recent years, tubular nanostructures have been related with immense advances in various fields of science and technology. Considerable research efforts have been centered on the theoretical prediction and manufacturing of non-carbon nanotubes (NTs), which meet modern requirements for the developing of novel devices and systems. In this context, diatomic inorganic nanotubes formed by atoms of elements from the 13th group of the periodic table (B, Al, Ga, In, Tl) and nitrogen (N), have received much research attention. In the present work, the elastic properties of single-walled boron nitride, aluminium nitride, gallium nitride, indium nitride and thallium nitride nanotubes were numerically evaluated using the nanoscale continuum modelling approach (also called molecular structural mechanics). The elastic properties (rigidities, surface Young´s and shear moduli, and Poisson´s ratio) of nitride nanotubes are discussed with respect to the bond length of the corresponding diatomic hexagonal lattice. The results obtained contribute to a better understanding of the mechanical response of nitride compound-based nanotubes, covering a broad range from the well-studied boron nitride NTs to the hypothetical thallium nitride NTs.

Broad bean paste (BBP) is a traditional fermented soy food, and its high salt content not only prolongs the fermentation time but also threatens human health. In this study, three BBP-meju with different salt concentrations were prepared, and the effects of varying salinity on the fermentation process were comprehensively compared. The results showed that salt-reduced fermentation contributed to the accumulation of amino acid nitrogen, reducing sugars, free amino acids, and organic acids. Alcohols, esters, aldehydes, and acids were the main volatile flavor compounds in BBP-meju, and the highest total volatile flavor compounds were found in medium-salt meju. Bacillus, Staphylococcus, Aspergillus, and Mortierella were the dominant microbial communities during fermentation, and there were also three opportunistic pathogens, Enterobacter, Pantoea, and Brevundimonas, respectively. According to Spearman correlation analysis, Wickerhamomyces, Bacillus, Staphylococcus, and Mortierella all showed highly significant positive correlations with ≥3 key flavor compounds, which may be the core functional flora. Furthermore, the dominant microbial genera worked synergistically to promote the formation of high-quality flavor compounds and inhibit the production of off-flavors during salt-reduced fermentation. This study provides a theoretical reference for the quality and safety control of low-salt fermented soy foods.

Soil organic matter (SOM) is important for the global carbon cycle, and hyperspectral remote sensing has proven a promising method for fast SOM content estimation. However, soil physical properties significantly affect the sensitivity of satellite hyperspectral imaging to SOM, leading to poor generalization ability of the estimation model. This study aims to improve the spatiotemporal transferability of the SOM prediction model by alleviating the coupling effect of soil physical properties on the spectra. Based on satellite hyperspectral images and soil physical variables, including soil moisture (SM), soil surface roughness (root mean squared height, RMSH), and soil bulk weight (SBW), a soil spectral correction strategy was established based on the information unmixing method. Two important grain-producing areas in Northeast China were selected as study areas to verify the performance and transferability of the spectral correction model and SOM content prediction model. The results showed that soil spectral corrections based on fourth-order polynomials and the XG-Boost algorithm had excellent accuracy and generalization ability, with residual predictive deviations (RPD) exceeding 1.4 in almost all bands. In addition, when the soil spectral correction strategy was adopted, the accuracy of the SOM prediction model and the generalization ability after model migration were significantly improved. The SOM prediction accuracy based on the XG-Boost corrected spectrum was the highest, with a coefficient of determination (R2) of 0.76, root mean square error (RMSE) of 5.74 g/kg, and RPD of 1.68. The prediction accuracy, R2, RMSE, and RPD of the model after migration were 0.72, 6.71 g/kg, and 1.53, respectively. Compared with the direct migration prediction of the model, adopting the soil spectral correction strategy based on fourth-order polynomials and XG-Boost reduced the RMSE of the SOM prediction results by 57.90% and 60.27%, respectively. The performance comparison highlighted the advantages of considering soil physical properties in regional-scale SOM prediction.

Extruded polystyrene (XPS) is frequently used in the construction of many different structures. It is therefore necessary to appropriately characterize its mechanical properties to ensure the safety of said structures. Among the available characterization tests, static bending tests are simple and easy to perform; owing to these characteristics, they should be performed more frequently than other tests. However, in static bending tests on XPS, there are several challenges owing to the high flexibility of XPS, and the chosen testing method and sample configuration affect the accuracy of characterization. In this study, three bending properties (Young’s modulus, proportional limit stress, and bending strength) of samples cut from an XPS panel were determined using three-point bending (TPB), four-point bending (FPB), and compression bending (CB) tests with varying sample span/depth ratios, and statistical analyses were performed to determine the relevance of the tests. The experimental results suggest that the TPB and CB tests were more feasible than the FPB test when the span/depth ratio was appropriately determined. However, clear differences were observed in the sample bending properties determined in these tests. In light of these findings, further studies should be conducted to elucidate these differences.

The aim of the present study was to investigate the incidence of breast (females), prostate, testicular and thyroid cancer in the Italian National Priority Contaminated Sites (NPCSs), served by cancer registries, where the presence of endocrine disruptors (EDs), reported to be linked to these tumors, was documented. Evidence of carcinogenicity of EDs present in NPCs was assessed based on evaluation by international scientific institutions/committees. Standardized Incidence Ratios (SIRs) were computed for each NPCS and cancer site with reference to the time window 1996-2005. Excess incidence of one or more cancer site at study was found in twelve out of fourteen NPCSs. Significantly increased SIRs were found for breast cancer in eight NPCSs, for prostate cancer in six, for thyroid cancer (both gender) in four and for testicular cancer in two. Non significantly increased SIRs were found in five NPCSs for testicular cancer and in two for thyroid cancer (males). Even if increased incidence of one or more cancer sites at study were found in several NPCSs, the ecological study design and the multifactorial etiology of the considered tumors do not allow reaching conclusions in terms of causal links with environmental contamination. In light of the observation of some excesses in SIRs, continuing epidemiological surveillance is warranted.

Berberis vulgaris (L.) has remarkable ethnopharmacological properties and is widely used in traditional medicine. The present study investigates B. vulgaris stem bark (Berberidis cortex) by extraction with 50% ethanol. The main secondary metabolites were quantified, resulting in a polyphenols content of 17.6780 ± 3.9320 mg Eq Tannic acid / 100 g extract, phenolic acids amount of 3.3886 ± 0.3481 mg Eq Chlorogenic acid / 100 g extract and 78.95 µg/g berberine. The dried hydro-ethanolic extract (BVE) was thoroughly analyzed using Ultra-High Performance Liquid Chromatography coupled with High-Resolution Mass Spectrometry (UHPLC–HRMS/MS) and HPLC and 40 bioactive phenolic constituents were identified. Then, the antioxidant potential of BVE was evaluated using three methods; our results could explain the protective effects of Berberidis cortex EC50FRAP = 0.1398 mg/mL, IC50ABTS = 0.0442 mg/mL, IC50DPPH = 0.2610 mg/mL compared to ascorbic acid (IC50 = 0.0165 mg/mL). Next, the acute toxicity and teratogenicity of BVE and Berberine - Berberine sulfate hydrate (BS) - investigated on Daphnia sp reported significant BS toxicity after 24 h; BVE revealed considerable toxicity after 48 hours and induced embryonic developmental delays. Finally, the anticancer effects of BVE and BS were evaluated on different tumor cell lines after 24 and 48 hours of treatments. The MTS assay evidenced a dose- and time-dependent antiproliferative activity, higher on BS than BVE. The strongest diminution of tumor cell viability was recorded on breast (MDA-MB-231), colon (LoVo) cancer, and OSCC (PE/CA-PJ49) cell lines after 48 h of exposure (IC50 < 100 µg/mL). However, no cytotoxicity was reported on normal epithelial cells (HUVEC) and hepatocellular carcinoma (HT-29) cell lines. Extensive data analysis supports our results, showing a significant correlation between the BVE's concentration, phenolic compounds content, antioxidant activity, exposure time, and the viability rate of various normal cells and cancer cell lines.

CoCrFeNiMn high-entropy alloy coatings were prepared on compacted graphite iron（CGI） through plasma cladding to strength the CGI substrate. The effects of heat treatment temperatures and times on the microstructure and mechanical properties of the CoCrFeNiMn coatings were investigated. After heat treatment, a single FCC phase was remained in the coating as compared to the deposited one, with smaller dendrites, larger dendritic spacing and more Cr-rich compounds precipitated between dendrites. The coatings’ microhardness was increased after heat treatment. After heat treated at 660°C for 90 minutes, the coating had the highest microhardness of 563±6.9 HV0.2, the lowest frictional coefficient of 0.71 and the smallest wear mass loss of 1.12 mg, and it had the best wear resistance.

The effects of rare earth Ce on the microstructure and properties of cast pure copper were investigated through thermodynamic calculations, XRD analysis, mechanical testing, metallographic microscopy, and scanning electron microscopy (SEM). The experimental results demonstrate that the reaction between rare earth Ce and oxygen as well as sulfur in copper exhibits a significantly negative Gibbs free energy value, indicating a strong thermodynamic driving force for deoxidation and desulfurization reactions. Ce is capable of removing trace amounts of O and S from copper. Moreover, the maximum solid solubility of Ce in Cu falls within the range of 0.009% to 0.01%. Furthermore, Ce can refine columnar grains while enlarging equiaxed grains in as-cast copper.Upon addition of rare earth Ce, the tensile strength increased by 8.45%, elongation increased by 12.1%, and microhardness rose from 73.5HV to 81.2HV-an increase of 10.5%. Overall, rare earth Ce has been found to enhance both the microstructure and mechanical properties of cast pure copper.

The unique structure of G4.0 PAMAM dendrimers allows the drug to be enclosed in internal spaces or immobilized on the surface. In the conducted research, the conditions for the formation of the active G4.0 PAMAM complex with doxorubicin (DOX) were optimized. The physicochemical properties of the system were monitored using DLS, CD, and fluorescence spectroscopy. The QCM-D method was chosen to determine the preferential conditions for the complex formation. The highest binding efficiency of the drug to the cationic dendrimer was observed under basic conditions when the DOX molecule was deprotonated. The decrease in the zeta potential of the complex confirms that DOX immobilizes through electrostatic interaction with the carrier's surface amine groups. The binding constants were determined from the fluorescence quenching of the DOX molecule in the presence of G4.0 PAMAM. The two-fold way of binding doxorubicin in the structure of dendrimers was visible in the ITC isotherm. Fluorescence spectra and release curves identified reversible binding of DOX to the nanocarrier. Among the selected cancer cells, the most promising anticancer activity of G4.0-DOX was observed in A375 malignant melanoma cells. Moreover, the preferred intracellular location of the complexes concerning the free drug was found, which is important from a therapeutic point of view.

Two experiments were conducted to develop a Nano green manganese and assess its effect on grapevines. The first experiment was microbiological, where several incorporation strategies were utilized to enrich the yeast with manganese, as follows: (1) adding manganese to the liquid medium (growth phase), (2) adding after 24 h of incubation (non-growth phase). As the results, growth phase reduced the possibility of medium contamination. Manganese concentration in the yeast cells was increased as that of manganese sulphate in the medium. Manganese incorporation in yeast cells was 99.93% higher than that of the medium at 0.0195 g/l of manganese. Although the concentration of manganese in the medium raised the OD of yeast cell biomass, manganese sulphate had no passive influence on it. The second experiment was horticultural, done on Flame Seedless grapevines, since both active fresh and frozen yeast enriched with manganese resulted from the first experiment were sprayed twice a year at 10 or 20 cm3/l comparing with manganese sulphate, and manganese chelate. The results demonstrated that yeast extracts in both forms increased the yield and improved fruit properties. The most effective treatment on vegetative growth, yield and fruit properties was the frozen yeast enriched with manganese at 20 cm3/l.

Integrating nanomaterials like carbon nanotubes (CNTs) and iron oxide (Fe₃O₄) into epoxy composites has significant interest due to their potential to enhance mechanical properties. This study evaluates the impact of dispersion quality on the mechanical performance of CNT/Fe₃O₄/Epoxy composites, comparing stirring and sonication methods at three different loadings: 0.1, 0.3, and 0.5 wt.%. Tensile testing revealed that sonicated composites consistently outperformed stirred composites, with a significant increase in elastic modulus and ultimate tensile strength (UTS). However, fracture strain decreased in both composite types compared to pure epoxy, with sonicated composites experiencing a more significant reduction than stirred composites. These results underscore the importance of high-quality dispersion for optimizing mechanical properties.

This study presents an innovative approach for the utilization of industrial by-products and municipal waste in the production of sustainable and environmentally friendly cement mortar. We explored stabilized stainless-steel reduced slag (SSRS) and polyethylene (PE) plastic waste as partial replacements for aggregates. Various engineering properties of the resulting cement mortar specimens, including slump, slump flow, compressive strength, flexural strength, tensile strength, water absorption, and ultrasonic pulse velocity (UPV), were investigated through comprehensive experimental tests. The influence of different water-cement (w/c) ratios and substitution amounts on the engineering properties of the cement mortar samples was thoroughly examined. The findings revealed that an increase in PE substitution adversely affected the overall workability of the cement mortar mixtures, whereas an increase in SSRS amount contributed to enhanced workability. As for the hardened properties, a consistent trend was observed for both cases, with higher w/c ratios and substitution amounts leading to reduced mechanical properties. Water absorption and UPV test results validated the increased formation of porosity with higher w/c ratios and substitution amounts. This study proposes a promising method to effectively repurpose industrial by-products and municipal wastes, transforming them into sustainable construction and building materials. Additionally, a comparative analysis of transportation costs and carbon footprint emissions between SSRS-cement mortar and PE-cement mortar was conducted to assess their environmental impact and sustainability. Generally, higher w/c ratios and replacement levels corresponded to reduced carbon footprint. The geographical location of the source of SSRS and PE remains a challenge and studies to overcome this challenge must be further explored.

Organic fertilizer application in agricultural land is known to improve soil microbial processes, fertility, and yield. In particular, stable changes in soil chemical composition through multi-year fertilization of organic fertilizers are thought to cause changes in the microbial community. Here, the effects of oil cake amendments (OC) on soil bacterial diversity, community profile and enzyme activity were evaluated and compared to those amended with chemical fertilizer (NPK). The comparison of diversity indices between OC and NPK amended soils shows that application of oil cake has increased microbial diversity potentially with an increase in the number of different microbial groups. The ordination plot distinguished and clustered both treatments showing differential effects of soils chemical factors on the microbial communities of each treatment. Proteobacteria, Verrucomicrobia and Bacteriodetes were significantly abundant in OC amended soil than in the NPK received soil, indicating alterations in community structure, composition, and diversity con-current to the changes in pH, Ca and Mg contents of the soil. These shifts in bacterial community structure and composition could also be observed from the phylum to the genus level in both NPK and OC amended soils partially explained by differences in soil chemical factors. The OC soil compared to the NPK amended soil also contain significantly higher abundance of predicted genes corresponding to enzymes related to biogeochemical cycling, decomposition and plant growth promotion. Collectively, these results support the use of an unconventional organic fertilizer positively altering bacterial populations in jujube orchards. The application of oil cake-based organic fertilizer improved microbial diversity and enhanced potential ecosystem functions related to bio-geochemical cycles, mineralization and plant growth promotion.

This work investigated the isothermal holding time dependence of the densification, microstructure, weight loss and tensile properties of Fe-Mn-Si powder compacts. Elemental Fe, Mn and Si powder mixtures with a nominal composition of Fe-28Mn-3Si (in weight percent) were ball milled for 5h and subsequently pressed under a uniaxial pressure of 400 MPa. The compacted Fe-Mn-Si powder mixtures were sintered at 1200 ℃ for 0, 1, 2 and 3 h, respectively. In general, the density, weight loss and tensile properties increased with the increase of isothermal holding time. A significant increase in density, weight loss and tensile properties occurred in the compacts isothermally holding for 1 h, as compared to those with no isothermal holding. However, further extension of isothermal holding time (2 and 3 h) only played a limited role in promoting the density and tensile properties. The weight loss of the sintered compacts was mianly caused by the sublimation of Mn in Mn depletion region on the surface layer of the sintered Fe-Mn-Si compacts. The length of the Mn depletion region increased as isothermal holding time increased. A single α-Fe phase was detected on the surface of all the sintered compacts, and the locations beyond the Mn depletion region were comprised of a dual dominant γ-austenite and minor ε-martensite.

Visible-light photocatalysis, particularly in its application to organic synthesis, has experienced a big renaissance in the past decade. The rational design of new photocatalysts with designed and improved photocatalytic properties, that at the same time circumvents the necessity of using scarce and toxic transition metals, will predictably play a key role in photocatalysis in the next few years. Although free-base porphyrins were identified some years ago as a promising, easily accessible and easily tunable class of organic photoredox catalysts, a systematic study on the effect of the electronic nature and of the position of the substituents on both the ground-state and the excited-state redox potentials of these compounds is still lacking. We have prepared a set of known functionalized derivatives of meso-tetraphenyl porphyrin containing different substituents either in one of the meso-positions or at a beta-pyrrole carbon and we have determined their ground- and (singlet) excited-state redox potentials. This survey has led us to conclude that the introduction of a carbonyl group at the beta-pyrrolic position strongly increases the facility of the monoelectronic reduction of the porphyrin both in the ground state and in the singlet excited state. We have also prepared a second set of four previously unknown benzoyl derivatives of meso-tetraphenylporphyrin, and we have confirmed the validity of our conclusions.

MicroRNAs (miRNAs) play important roles in the control of HIV-1 infection. Here, we performed RNAseq profilings of miRNAs and mRNAs expressed in CD4+ T-lymphocytes upon HIV-1 infection. Our results reveal significant alterations of miRNAs and mRNAs expression profiles in infected relative to uninfected cells. One of the miRNAs markedly downregulated in infected cells is miRNA-26a. Among the putative targets of miRNA-26a are CD59 receptor transcripts, which are significantly upregulated in infected CD4+ T-cells. Addition of miRNA-26a mimics to CD4+ T-cells reduces CD59 at both mRNA and surface protein levels, validating CD59 as a miRNA-26a target. Consistent with the reported inhibitory role of CD59 in complement-mediated lysis (CML), knocking-out CD59 in CD4+ T-cells renders both HIV-1 infected cells and progeny virions more prone to antibody-dependent CML (ADCML). Addition of miRNA-26a mimics to infected cells leads to enhanced sensitivity of progeny virions to ADCML, a condition linked to a reduction of CD59 packaging into released virions. Lastly, HIV-1-mediated downregulation of miRNA-26a expression is shown to be dependent on integrated HIV-1 expression but does not involve viral accessory proteins. Overall, these results highlight a novel mechanism by which HIV-1 limits ADCML by upregulating CD59 expression via miRNA-26a downmodulation.

Medicinal mushrooms, especially Ganoderma species hold immense promise for production of a wide range of bioactive compounds with various effects. The biochemical potential of indigenous fungal strains, specific to a region, could play a critical role in the continuous search for novel strains with superior activities on a global scale. This research focused on the ethanolic (EtOH) and hot-water (H2O) extracts of fruiting bodies of two wild-growing Ganoderma species: G. pfeifferi and G. resinaceum with an aim to assess its nutritional (total carbohydrate content-TCC), and mineral composition in relation to bioactive properties: antioxidant, antiproliferative and lipid-lowering. Atomic absorption spectrophotometry (AAS) revealed that G. pfeifferi is a promising source of minerals that are essential for numerous physiological functions in the human body like bone health and muscle and nerve function, with calcium (Ca 4.55 ± 0.41 mg/g d.w.) and magnesium (Mg 1.33 ± 0.09 mg/g d.w.), being the most abundant macro element present. Zinc (Zn), manganese (Mn), and chromium (Cr) were particularly notable, with concentrations ranging from 21.49 to 41.70 mg/kg d.w. The EtOH extract of G. pfeifferi demonstrated significantly elevated levels of TCC, essential macromolecules for energy and structural functions in the body, with higher quantities of all three standard carbohydrates detected in this type of extract. Similar to revealed composition the same species, G. pfeifferi stood out as the most prominent antioxidant agent, with H2O extract being stronger than EtOH in ABTS assay (86.85 ± 0.67 mg TE/g d.w.), while EtOH extract displayed the highest anti OH• radical scavenging ability (IC50 = 0.18 ± 0.05 μg/mL) as well as the most notable reducing potential among all. The highest antiproliferative effect against the breast cancer cell line (MCF-7), demonstrated the H2O extracts from G. resinaceum with the most pronounced activity after 24 hours (IC50 = 4.88 ± 0.50 μg/mL) which surpasses that of the standard compound, ellagic acid (IC50 = 33.94 ± 3.69 μg/mL). Administration of both Ganoderma extracts mitigated diabetic lipid disturbances and exhibited potential renal and hepatic protection in vivo on white Wistar rats by preservation of kidney function parameters in G. resinaceum H2O pre-treatment (urea: 6.27 ± 0.64 mmol/L, creatinine: 50.00 ± 6.45 mmol/L) and the reduction of ALT levels (17.83 ± 3.25 U/L) com-pared to diabetic control groups treated with saline (urea: 46.98 ± 6.01 mmol/L, creatinine: 289.25 ± 73.87 mmol/L, and ALT: 60.17 ± 9.64 U/L). These results suggest that pre-treatment with G. resinaceum H2O extracts may have potential antidiabetic properties. In summary, detected microelements are vital for maintaining overall health, supporting metabolic processes, and protecting against various chronic diseases. Further research and dietary assessments could help determine the full potential and applications of two underexplored Ganoderma species native to Serbia in nutrition and health supplements.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

The poly lactic acid (PLA) is one of the most used bio-derived thermoplastic polymers in 3D and 4D printing applications. The determination of PLA surface properties is of capital importance in 3D/4D printing technology. (1) Background: The surface thermodynamic properties of PLA polymer were determined by using the inverse gas chromatography (IGC) technique at infinite dilution. The determination of the retention volume of polar and non-polar molecules adsorbed on the PLA particles filling the column allowed us to obtain the dispersive, polar, and Lewis’s acid-base surface properties at different temperatures from 40 °C to 100 °C. (2) Methods: the applied surface method was based on our recent model that used the London dispersion equation and the new chromatographic parameter function of the deformation polarizability and the harmonic mean of the ionization energies of the PLA polymer and organic molecules. (3) Results: The application of this new method led to the determination of the dispersive and polar free surface energy of adsorption of molecules on the polymeric material, as well as the glass transition and the Lewis acid-base constants. (4) Conclusions: four interval temperatures were distinguished showing four zones of the variations of the surface properties of PLA as a function of the temperature before and after the glass transition.

In this study, 10%PTFE/PEEK blend were modified by potassium titanate whisker (PTW) and chopped glass fiber (GF), respectively. The blends were prepared by three-screw extruder. Through the investigation of thermal stability, tribological properties, mechanical properties and rheological behavior, the effects of reinforcing agents were determined. The results illustrated that the mechanical properties of 10%PTFE/PEEK blend can be dramatically improved by adding reinforcing agent of PTW or GF, and the reinforcing effect of GF was especially obvious. As for tribological properties, 1% addition was the best proportion. The friction coefficient and wear rate of the blend with 1% PTW were 0.283 and 4.97 × 10^-6 mm³/N · m, which decreased by 7.2% and 21% compared with those of the blend without reinforcing agent.

In this study, a new type of temperature sensor device was developed. The circular electrode of the thermal sensitive sensor was modified with TMT and O₂ plasma to enhance the conductivity by forming a thin SnOxCy layer on the electrode surface. The Nano-Au particles were subjected to O₂ plasma pretreatment to form peroxide groups on the surface. The thermally sensitive sensor was made by mixing the above-treated Nano-Au particles with N-isopropylacrylamide (NIPAAm) to form solution and then UV-induced grafting polymerization of the NIPAAm-containing solution onto the electrode substrate. The composite hydrogels on the electrode introduce thermo-sensitive polymeric surface films for temperature sensing. Using ambient environment resistance test to measure the resistance, the LCST (lower critical solution temperature) of Nano-Au (MUA) mixed with NIPAAm hydrogel was found to be 32 °C. At ambient temperatures higher than LCST, the electrode resistance decreases linearly.

Over the past few decades, synthetic polymer production has increased, and the production of plastics has surpassed all other man-made materials due to their versatility. Moreover, packaging plastic makes up around 40% of global plastic production. However, the excessive usage of synthetic packaging materials has led to severe environmental and health-related issues. Therefore, biobased packages are considered alternatives to substitute synthetic packaging on the market. Furthermore, the choice of packing material in the food industry is a perplexing process as it depends on various factors, such as the type of food product, its sustainability, and environmental conditions. Interestingly, due to proven gas barrier properties and biological activity, polysaccharide-based bioplastics show the potential to expand the trends in food packaging, including edible films and intelligent and active food packaging. This review discusses the structure, properties and recent developments in polysaccharide-based bioplastics as food packaging materials.

The alcoholic fermentation process with agitation/static, followed by the acetic fermentation submerged in banana was evaluated. Kinetics parameters of alcoholic fermentation for the maximum ethanol/glycerol metabolites in agitated process was 29 and 27 h, and in static 47 and 45 h, respectively. For acetic fermentation, the kinetics parameters were medium time of 39.9 h, acetic acid yield of 53.1% and acetic acid productivity of 0.216 g/Lh. Wines from agitated/static process presented 5.73 and 6.81% (v/v) of alcohol content, respectively. Wine obtained by the static process presented higher concentrations of volatile compounds. The vinegar showed 49.2 g/L of acetic acid and the esters concentrations were higher than in wine. The wine and vinegar minerals were consistent with amount observed in the pulp, with an increase in sulphur concentration after alcoholic fermentation and decrease after acetic fermentation. Products showed chemical and composition of sensory and nutritional interest.

In spite of the significant progress towards sustainable cosmetics, mass-produced sustainable packaging has proven to be a challenge. The complexity of environmental, economic, social, technological and policy considerations in conjunction with varying consumer behaviors and corporate goals can make it difficult to select an optimal strategy across heterogeneous supply-chain components spread over the globe; and the cost and effort of developing, testing and validating alternative strategies discourages empirical exploration of potential alternatives. This review discusses the challenges that can be expected in the context of broader sustainability efforts, as well as the experience gained in related fields such as sustainable cosmetics and sustainable packaging, to identify potential pitfalls as well as promising trends towards development of sustainable cosmetics packaging. The findings suggest there may be little to be gained from attempting to induce customers to change their behavior; waiting for a significant increase in global recycling infrastructure; or expecting regulatory constraints to substitute for the lack of technological and business solutions. A research strategy is delineated towards development of sustainable packaging that, with appropriate policy support, could minimize externalities and provide mass-produced packaging that is acceptable to both consumers and producers.

The study involved a comparison of the chemical, physical, microbiological, and functional attributes of must extracted from Solaris cultivar grapes cultivated under both conventional and organic farming systems. This study aimed to determine the influence of cultivation methods on various must properties, including the levels of health-promoting polyphenols and health-threatening mycotoxins and pesticide residues. It was observed that the organic grapes hosted a greater diversity and quantity (OTUs) of bacteria and fungi. The predominant bacteria were Sphingomonas (with similar numbers in both crops) and Massilia (more abundant in grapes from the conventional crop). These two bacterial groups collectively accounted, on average, for about 40% of all OTU sequences detected. Lower levels of bacteria of the genera Hymenobacter and Pseudomonas and others colonized the grapes. Among the fungi, Erysiphe and Aureobasidium were dominant, comprising about 50–70% of all detected taxa. Notably, Erysiphe was predominantly found in conventionally grown grapes, while Aureobasidium, Mycosphaerella, and Botryotinia were present in comparable quantities in fruit from both types of crops. No mycotoxins were detected in the must or marc, despite the presence of genes responsible for aflatoxin and ochratoxin biosynthesis in both types of grape juice. The organic must exhibited significantly higher levels of polyphenols and displayed improved antioxidant properties and technological characteristics. Moreover, sulfur and copper used in the protection of the organic plantation passed from the fruit surface into the must. Also, pesticide residues, namely cyprodinil and fludioxonil from conventional cultivation, were detected in the must.

Preventing the occurrence of secondary caries serves as one of the significant issues in dental clinic, thus make it indispensable to improving the properties of conventional composite resin (CR) by developing a novel CR. In present study, two groups of experimental CRs loaded with different contents of fluoride-doped nano-zirconia fillers (25 wt% and 50 wt%) were fabricated. The surface topography, mechanical performance, fluoride release, antibacterial effect, aging property and cytotoxicity of the experimental CRs were evaluated subsequently. A uniform distribution of the F-zirconia fillers over the whole surface of resin matrix could be observed. The experimental CRs showed continuous fluoride release within 28 days, which was positively correlated with the content of F-zirconia fillers. Moreover, the amount of fluoride release increased in the acidic buffer. Addition of F-zirconia fillers could improve the color stability, wear resistance and microhardness of the experimental CRs, without reducing the flexure strength. Furtherly, the fluoride ions released continuously from the experimental CRs resulted in effective contact and antibacterial properties, while they showed no cytotoxicity. As a consequence, considerations can be made to employ this new kind of composite resin loaded with fluoride-doped nano-zirconia fillers to meet clinical requirements when the antimicrobial benefits are desired.

Scientific studies on the impact of wood species on solid fuel production, performance, and sustainability are grossly inadequate. The knowledge of this is imperative as users of solid fuels are increasing rapidly, especially in Africa. On this note, it becomes necessary to explore measures that will improve its efficiency and sustainability as an energy source. This study investigates some properties of selected wood species used as an energy source in Nigeria and their pelleting potential. Nine (9) samples were characterized and assessed for suitability of pelleting following four wood pellet quality standards. The findings revealed Anogeissus leiocarpus as the species with the best rating score in terms of fuel properties while Vitellaria paradoxa as the lowest. However, in terms of conformity with the four wood pellets standards, Khaya senegalensis, Parkia biglobosa and Anogeissus leiocarpus having presented density, calorific value, sulfur, arsenic, cadmium, and lead within the limits of the wood pellet quality standards were considered the best wood species in terms of fuel suitability and pelleting potential. The findings therefore suggest that not all wood species are suitable as fuel. Thus, for species that do not meet the standard wood pellet requirements, alternatives such as the use of biomass blends, additives, or process adjustments can be employed to adapt the quality to the standards or by using the fuels in improved cookstoves.

The changes in consumer lifestyles have raised awareness of the variety of food options and packaging technologies. Active and smart packaging represents an innovative technology that serves to enhance the safety and quality of products. Smart packaging, as a subset of this technology, entails the integration of additives into packaging materials, thereby facilitating the preservation or extension of product quality and shelf life. This technological approach stimulates a heightened demand for safer food products with prolonged shelf life. Active packaging predominantly relies on the utilization of natural active substances. Therefore, the combination of active substances has a significant impact on the characteristics of active packaging particularly on polymeric blend like Polylactic acid (PLA) as a matrix. So, This review will summarize and explains how the addition of natural active agents influenced the properties related to the performance of active packaging through systematic analysis, providing new insights about the relationship between the types of active agents on physical-mechanical properties, bacterial colony reduction, and applications in foods packaging such as meat, fish, fruit, and vegetables. Through their integration, the market for active and smart packaging systems is expected to have a bright future.

Ten new Schiff bases, including thiocarbohydrazone derivatives (1–10), were synthesized using an efficient, uncomplicated, and environmentally friendly approach using the reaction of alkyl-substituted aldehydes. The thiocarbohydrazones that were obtained were derived from o-phthalaldehyde. The chemical structures of the compounds were identified by the utilization of UV-Vis spectroscopy, Fourier transform infrared (FT-IR), ¹H nuclear magnetic resonance (¹H NMR), ¹³C nuclear magnetic resonance (¹³C NMR), and elemental analysis methods. The thermal stability of thiocarbohydrazones was examined using thermogravimetric analysis (TGA-DSC). Investigations were conducted on urease inhibition tests, pharmacokinetic property research, and molecular docking. The collection of samples with the urease enzyme revealed significant molecular docking findings, with MolDock scores ranging from -153 to -189. The compounds have the potential to be effective drug candidates for treating certain diseases, as indicated by the consistent results of molecular docking, urease inhibition tests, and pharmacokinetic characteristics investigations.

To improve efficacy and safety of sunscreen emulsions, UV‐filter skin permeation could be kept as low as possible by reducing UV‐filter content or changing emulsion composition. In this work, different lipid phase ratio (12, 14 and 16% w/w) were assessed for their ability to affect the technological and sensory properties of O/W emulsions in which bemotrizinol (BMTZ), a broad spectrum sunscreen agent, was incorporated free or loaded into nanostructured lipid nanocarriers (NLC) to reduce its release from the vehicle and, hence, its skin permeation. The following technological properties were evaluated in vitro by suitable methodologies: spreadability, viscosity, pH, occlusion factor, BMTZ release, sun protection factor (SPF). Sensory attributes were assessed by trained panelists in three different phases: before/during pick‐up, rub‐in, after application. Raising the lipid phase ratio led to an increase of viscosity and to a corresponding drop of spreadability while the incorporation of BMTZ‐loaded NLC determined a decrease of occlusion factor and an increase of SPF. No BMTZ release was observed from all emulsions. Sensory attributes were mainly affected by lipid phase ratio. These results suggest that lipid phase ratio and BMTZ incorporation into NLC could contribute to determine technological and sensory properties of O/W emulsions.

Spent coffee grounds (SCG) have great potential as a useful, value-added biological material. In this context, activated carbon (AC) was prepared from SCG by an activation process using H3PO4 at 600°C in air and used as an adsorbent for the azo dye AO7, a model molecule for dye colorants found in textile industry effluents. X-ray diffraction, SEM and BET revealed that the AC was predominantly amorphous, consisting of a powder of 20-100 µm particles with mesopores averaging 5.5 nm in pore size. Adsorption kinetics followed a pseudo-second-order law, while the Langmuir model best fitted experimental isotherm data (maximum capacity of 119.5 mg AO7 per AC g). Thermodynamic parameters revealed that adsorption was endothermic and spontaneous. All the characterizations indicated that adsorption occurred by physisorption via mainly - interactions. The best experimental removal efficiency optimized by means of a Box-Behnken design and response surface methodology was 98% for an initial AO7 concentration of 20 mg.L-1 at pH 7.5 with a dose of 0.285 g.L-1 of AC and a contact time of 40 min. These results clearly show that activated carbon prepared from SCG can be a useful material for efficiently removing organic matter from aqueous solutions.

In this study, the mechanical and piezoresistive properties of mortars reinforced with carbon nanotubes (CNTs) and carbon micro fibers (CMFs) are determined. Silica fume as well as a polymer with polyalkylene glycol graft chains were used as dispersant agents for the CNTs and CMFs incorporation into the cement paste. The mechanical properties of the mortar composites were investigated in respect to their flexural and compressive strength. A four-probe method was used for the estimation of their piezoresistive response. The test outcomes revealed that the combination of the dispersant agents along with a low content of CNTs and CMF by weight of cement (bwoc) result in the production of a stronger mortar with enhanced mechanical performance and durability. More specifically, there was an increase in flexural and compressive strength up to 38% and 88%, respectively. Moreover, the piezoresistive response of the reinforced cementitious materials was attributed to the variation of electrical resistivity due to tunneling transport of electrons stemming from two different mechanisms due to the incorporation of the conductive admixtures (CNTs and CMF). This work aims to contribute to the progress acceleration in the field of developing structural materials with self-sensing and electrical actuation related properties.

The paper discusses the mechanism of montmorillonite structure alteration and bentonites properties modification (on the example of samples from clay deposit Taganka, Kazakhstan) due to the thermochemical treatment (treatment with inorganic acid solutions at different temperatures, concentrations and reaction times). With the use of the suit of methods certain processes were distinguished: transformation of montmorillonite structure, which appears in the leaching of interlayer and octahedral cations, protonation of the interlayer and OH groups at octahedral sheets. Changes in the structure of the 2:1 layer of montmorillonite and its interlayer result in significant changes in the properties – reduction of cation exchange capacity and an increase of specific surface area. The results of the work showed that bentonite clays retain a significant portion of its adsorption properties even after the long term and intense thermochemical treatment (6M HNO3, 60°C, 108 hours)

Traditional concrete pavements have poor water permeability, while the strength of pervious concrete pavements is low. To solve these problems, this study designed Innovative recycled aggregate pervious concrete (I-RAPC) with controllable water permeability and high strength by using response surface methodology, and investigated the effects of different pore parameters (number, diameter, material, distribution form, etc.) on the performance of I-RAPC. And the strength discount factor method was proposed to construct the theoretical calculation model of compressive strength and pipe pore parameters, and the calculation model of water permeability coefficient was established at the same time. The results show that the fewer the number of holes and the smaller the pipe diameter of I-RAPC, the higher its compressive strength and the smaller the water permeability coefficient. The theoretical model of compressive strength can accurately evaluate the discounting effect of the pore parameters on the compressive strength of I-RAPC, and the maximum relative error is only 7.52%, and the maximum relative error of the calculation model of water permeability coefficient is only 4.42%. I-RAPC has the advantages of high strength and permeability with controllable performance, which overcomes the problems of random distribution of pore space, uncertainty of water permeability, and strength of ordinary pervious concrete.

Many historic buildings and monuments on the Salento Peninsula (Apulia, southern Italy) were built from locally quarried Miocene calcarenites belonging to the Pietra Leccese Formation (Late Burdigalian-early Messinian). The main facies consists of a homogeneous and porous biomicrite, pale yellow in color and fine- to medium-grained, very rich in planktonic Foraminifera and massive or thick-bedded in outcrop. Additionally, there are other facies among which Piromafo stands out for its aesthetic appearance, which is enhanced by its greenish-brown or greenish-grey colors. Its physical characteristics, in terms of thermal properties mainly due to the mineral content and fabric, make it a good refractory and insulation material. Piromafo occurs in the upper part of the Pietra Leccese Fm. and is repre-sented by a fine- to medium-grained glauconitic and phosphatic biomicrite with macrofossils, es-pecially Bivalves and Gastropods. Despite its important historical use as building and ornamental material, especially in the Roman and Baroque architecture, a research gap exists in the scientific literature describing the properties of the stone and their correlation. Therefore, the aim of this paper is to present a wide range of properties useful to explain the in-situ behavior and damage susceptibility of the stone in monu-ments and buildings, but also for selecting preservation treatments and strategies. Thus, an overall assessment of the main petrophysical and mechanical properties especially for restoration/conservation purposes was performed using both standard and unconventional tech-niques. Starting from rock fabric inspection, particular attention was given to the relationship be-tween pore-size distribution and, hydraulic and thermal properties of the material. Unconfined compressive strength, flexural strength and indirect tensile strength were also estimated.

This review aims to describe an edible packaging system in food production. The growing global population, changes in climate and dietary patterns, as well as increasing need for environmental protection have created an increasing demand for waste-free food production. The need for durable and sustainable packaging materials has become significant to avoid food waste and environmental pollution. Edible packaging has emerged as a promising solution also to extend the shelf life of food products and reduce dependence on petroleum-based resources. In this review, the importance, composition, and functions of edible packaging materials, as well as their production methods, were described. The market value of edible packaging materials is expanding. It needs further research and development of edible packaging materials to increase sustainable, eco-friendly packaging practices significant for environmental protection and food safety.

Autologous platelet-rich plasma (PRP) preparations are prepared at point of care. Centrifugation cellular density separation sequesters a fresh unit of blood into three main fractions: a platelet-poor plasma (PPP) fraction, a stratum rich in platelets (platelet concentrate) and, bioformulation dependent, also leukocyte and erythrocyte fractions. The employment of autologous platelet concentrates facilitates the biological potential to accelerate and support in numerous cellular activities that can lead to tissue repair, tissue regeneration, wound healing, and ultimately functional structural repair. Normally, after PRP preparation the PPP fraction is discarded. One of the less well known, but equally important features of PPP is that particular growth factors (GFs) are not abundantly present in PRP, as they reside outside the platelet alpha granules. Precisely, insulin-like growth factor-1 (IGF-1) and hepatocyte growth factor (HGF) are mainly present in the PPP fraction. In addition to their roles as angiogenesis activators, these plasma-based GFs are also known to inhibit inflammation, fibrosis, and they promote keratinocyte migration and support in tissue repair and wound healing. Additionally, PPP is known for the presence of exosomes and other macrovesicles, exerting cell-cell communication and cell signaling. Newly developed ultrafiltration technologies incorporate PPP processing methods by eliminating in a fast and efficient manner plasma water, cytokines, molecules, and plasma proteins with a molecular mass (weight) less than the pore size of the fibers. Consequently, a viable and viscous protein concentrate of functional, total proteins, like fibrinogen, albumin, and alpha-2-macroglobulin is created. Consolidating a small volume of high platelet concentrate with a small volume of highly concentrated protein-rich PPP creates a protein rich platelet concentrate (PRPC) biological preparation. After the activation of proteins, mainly fibrinogen, the PRPC matrix retains and facilitates interactions between invading resident cells, like macrophages, fibroblast, and mesenchymal stem cells (MSCs), and the embedded concentrated PRP cells and molecules. The administered PRPC biologic will ultimately undergo fibrinolysis, leading to a sustained release of concentrated cells and molecules that have been retained in the PRPC matrix until the matrix is dissolved. We will discuss the unique biological and tissue reparative and regenerative properties of PRPC matrix.

Opuntia ficus-indica (L.) Mill. belongs to the Cactaceae family and the genus Opuntia; it is a succulent plant that adapts to extreme climatic conditions. The aerial part of the plant consists of the cladodes, morphological changes of branches that appear green, are covered with thorns, and are essential to reduce excessive perspiration of water. The composition of cladodes is very varied, and the main constituents are water, fibers, polysaccharides, proteins, fatty acids, vitamins, sterols, minerals, and polyphenols. Polyphenols are responsible for many beneficial activities for human health, such as antioxidant, anti-inflammatory, antitumor, and nutritional properties. The purpose of this manuscript was to compare the properties of cladodes belonging to the same plant but with different stages of maturity. Relative extracts were tested both in vitro and on a cell line and antioxidant and anti-apoptotic properties were found. The antioxidant activity was tested by the ORAC test, the DPPH test, and the measurement of cellular accumulation of ROS. Anti-apoptotic activity was evaluated by the annexin/PI assay and measurement of caspases 9 and 3 expression. The results obtained have shown that the extracts considered possess antioxidant and anti-apoptotic properties. However, the different stages of maturity of cladodes are essential for the performance of both functions. In addition, important variations have been made in the dissolution of extracts that have brought greater safety in their use. In conclusion, this manuscript provides further information on cladodes of Opuntia ficus-indica, which can be used as adjuvants in many human pathologies.

The effects of CO₂-water-rock interactions on the mechanical properties of shale are essential for estimating the possibility of sequestrating CO₂ in shale reservoirs. In this study, uniaxial compressive strength (UCS) tests together with an acoustic emission (AE) system and SEM & EDS analysis were performed to investigate the mechanical properties and microstructural changes of black shales with different saturation times (10 days, 20 days and 30 days) in water dissoluted with sub-/super-critical CO₂. According to the experimental results, the values of UCS, Young’s modulus and brittleness index decrease gradually with increasing saturation time in water with sub-/super-critical CO₂. Compared to intact samples, 30-days’ saturation causes reductions of 56.43% in UCS and 54.21% in Young’s modulus for sub-critical saturated samples, and 66.05% in UCS and 56.32% in Young’s modulus for super-critical saturated samples, respectively. The brittleness index also decreases drastically from 84.3% for intact samples to 50.9% for samples saturated in water with sub-critical CO₂, to 47.9% for samples saturated in water with super-critical carbon dioxide (SC-CO₂). SC-CO₂ causes a greater reduction of shale’s mechanical properties. The crack propagation results obtained from the AE system show that longer saturation time produces higher peak cumulative AE energy. SEM images show that many pores occur when shale samples are saturated in water with sub-/super-critical CO₂. The EDS results show that CO₂-water-rock interactions increase the percentages of C and Fe and decrease the percentages of Al and K on the surface of saturated samples when compared to intact samples.

Micro-Raman spectroscopy was carried out to evaluate the localized residual stresses in commercial Gallium Nitride-based devices, specifically AlGaN/GaN High Electron Mobility Transistors (HEMTs) in a novel packaging design provided by STMicroelectronics S.r.l. The packaging plays a key role in protecting the device core against the external environment, thus minimizing damages caused by mechanical shocks, exposure to light, and contact with chemicals, conjointly achieving an efficient heat dissipation rate. Even though the packaging is a required step for the proper functioning of ready-to-use electronic devices, its application typically may introduce mechanical stress to AlGaN/GaN HEMTs, which can result in various reliability issues. In this paper, we investigate the impact of packaging on residual stress by analyzing the frequency shift of the E2 Raman peak along GaN layers and at the GaN/Si interface. An extensive evaluation was conducted using both a packaged device and a wafer-level device. The correlation between Raman frequency shifts of the E2 mode was accurately quantified, revealing a stress mitigation of approximately 0.1 GPa. This reduction is ascribed to the compressive stress introduced by the packaging, which partially offsets the intrinsic tensile stress of the wafer-level device. The proposed methodology could, in principle, be implemented to improve the development of a packaging.

Due to the non-degradability of petroleum-based packaging materials, serious environmental pollution and the depletion of non-renewable resources have become pressing issues. In order to actively promote green production and address these concerns, there is an urgent need for new packaging materials to replace traditional plastic products. Starch-based packaging materials, composed of starch, fiber, and plasticizers, offer a degradable and environmentally friendly alternative. Starch alone cannot undergo thermoplastic processing due to its inherent structural characteristics. Therefore, researchers have explored modifications by incorporating plasticizers to create processable thermoplastic starch (TPS). However, there are challenges related to the high crystallinity and poor compatibility between TPS and fibers, resulting in decreased mechanical properties. To address these challenges, a novel approach combining plasticizer optimization and response surface method (RSM) optimization has been proposed to enhance the mechanical properties of starch-based packaging materials. This method leverages the advantages of composite plasticizers and process parameters. The findings demonstrate that the composite plasticizer effectively disrupt the hydrogen bonding and granule morphology of starch, leading to a significant reduction in crystallinity. Based on these findings, the optimal process parameters are determined using the RSM, resulting in a forming temperature of 198 °C, forming time of 5.4 minutes, and AC content of 0.84 grams. Compared with the non-optimized values, the tensile strength increases by 12.2% and the rebound rate increases by 8.1%.

The thermal surface properties of graphenes and carbon materials are of crucial importance in chemistry of materials, chemical engineering, and many industrial processes. (1) Background: The determination of these surface properties is carried out using inverse gas chromatography at infinite dilution which leads to the retention volume of organic solvents adsorbed on solid surfaces. This experimental and fundamental parameter actually reflects the surface thermodynamic interactions between injected probes and solid substrates. (2) Methods: The London dispersion equation and the Hamieh thermal model were used to quantify the London dispersive and polar surface energy of graphenes and carbon fibers as well their Lewis acid-base constants by introducing the coupling amphoteric constant of materials. (3) Results: The London dispersive and polar acid-base surface energies, the free energy of adsorption, the polar enthalpy and entropy, and the Lewis acid-base constants of graphenes and carbon materials were determined. (4) Conclusions: it was showed that graphene exhibited the highest values of London dispersive surface energy, polar surface energy, and Lewis’s acid-base constants. These highest characteristics of graphene justify its great potentiality and uses in many industrial applications.

Advanced 1H Nuclear Magnetic Resonance (NMR) relaxometry and diffusometry methods and VIS-nearIR spectroscopy combined with pH, electric conductivity (EC) and totally dissolved solids (TDS) measurements were used to assess the properties of wastewater collected from a chicken slaughterhouse in each step of the treatment process (wastewater before treatment, biologically treated wastewater, chemically treated wastewater and discharged wastewater) and from sludge. The 1H NMR Carr-Purcell-Meiboom-Gill (CPMG) and Pulsed-Gradient-Stimulated-Echo (PGSE) decay curves recorded for all samples of wastewater were analyzed by inverse Laplace transform (ILT) to obtain the distributions of transverse relaxation times T2 and diffusion coefficient D. The VIS-nearIR total absorbance, T2-values, D-values, pH, EC and TDS parameters were used for statistical analysis in principal component analysis (PCA). The 1H T2-distributions measured for the slaughterhouse wastewater lie in two main regions reflecting the amount of dissolved solids or the distribution of undissolved solids mobility. The PCA analysis successfully differentiates between polluted and less polluted types of wastewater and sludge. The wastewater treatment applied by the slaughterhouse is efficient. The recommended methods for wastewater monitoring are the NMR T2- and D-distributions and EC, TDS and NMR-D diffusion coefficient. Finally, Machine Learning AI-algorithms are used to provide prediction maps of wastewater treatment stage.

The temperature effect plays an important role for an accurate determination of the polar free energy, polar thermodynamic parameters, and enthalpic and entropic Lewis’s acid base properties of oxides, polymers and composites polymers/oxides. The adsorption of polymers on other solid surfaces is crucial in many industrial applications, coatings, paints, catalysis, colloids and adhesion processes. (1) Background: Inverse gas chromatography at infinite was used for the physico-chemical characterization of solid substrates by determining the thermodynamic parameters of adsorption of model organic solvents on solid surfaces such as polymers, metallic oxides, carbon fibers, pharmaceutical or 3D/4D printing substrates. (2) Methods: A new method based on the London dispersion equation was applied with a new parameter associating the deformation po-larizability and the harmonic mean of the ionization energies of solvent. More accurate values of the dispersive and polar interaction energies of the various organic solvents adsorbed on PMMA in bulk phase and PMMA/silica at different recovery fractions were obtained as well as the Lewis acid-base parameters and the transition temperatures of the different composites. (3) Results: This new methodology gave very interesting results on the behavior of PMMA adsorbed on silica. An important effect of the temperature and the recovery fraction on the various physicochemical and thermodynamic properties was highlighted. The variations of all interaction parameters showed the presence of three transition temperatures for the different PMMA adsorbed on silica with the various coverage rates with a shift of these temperatures for a recovery fraction of 31% (4) Con-clusions: An important variation of the polar enthalpy and entropy of adsorption, the Lewis ac-id-base parameters and the intermolecular separation distance as a function of the temperature and the recovery fraction of PMMA on silica.