Copper (Cu) is a critical element for cancer cell proliferation and considerably accumulates in the nucleus. 64Cu2+ is an anticancer radiopharmaceuticals targeting the copper requirement of cancer cells. However, intravenously injected 64Cu2+ ions primarily accumulate in the liver. Ligand complexation of 64Cu2+ would be a promising method for increasing tumor delivery by reducing liver uptake. Herein, we used three tripodal amine ligands [tris(2-aminoethyl)amine (Tren), diethylenetriamine (Dien), and tris(2-pyridylmethyl)amine (TPMA)] to enclose 64Cu2+ ions and compared their in vivo tumor and liver uptake using a tumor-bearing xenograft mouse model of the extrahepatic bile duct carcinoma cell line TFK-1. We examined intracellular Cu distribution using microparticle-induced X-ray emission (micro-PIXE) analysis for these compounds. 64Cu2+-Tren and 64Cu2+-Dien showed higher tumor uptake than 64Cu2+-TPMA and 64Cu2+ ions in TFK-1 tumors. Among the three 64Cu2+ complexes and 64Cu2+ ions, liver uptake was inversely correlated with tumor uptake. Micro-PIXE analysis showed that in vitro cellular uptake was similar to in vivo tumor uptake and nuclear delivery was the highest for 64Cu2+-Tren. Conclusively, an inverse correlation between tumor and liver uptake was observed using three 64Cu2+ complexes of tripodal amine ligands and 64Cu2+ ions. These results provide useful information for the future development of anticancer 64Cu radiopharmaceuticals.

The achievement of size uniformity and monodispersity in perovskite quantum dots (QDs) requires the implementation of precise temperature control and the establishment of optimal reaction conditions. Nevertheless, the accurate control of a range of reaction variables represents a considerable challenge. This study addresses the aforementioned challenge by employing manganese (Mn) doping to achieve size uniformity in CsPbBr₃ perovskite QDs without the necessity for precise control of the reaction conditions. By optimizing the Mn:Pb ratio, it is possible to successfully dope CsPbBr₃ QDs with appropriate concentrations of Mn²⁺ and achieve a uniform size distribution. The spectroscopic measurements on single QDs indicate that the appropriate Mn²⁺ concentrations can result in a narrower spectral linewidth, a longer photoluminescence (PL) lifetime, and a reduced biexciton Auger recombination rate, thus positively affecting the PL properties. This study not only simplifies the size control of perovskite QDs, but also demonstrates the potential of Mn-doped CsPbBr₃ QDs for narrow linewidth light-emitting diode applications.

The electric vehicle (EV) industry challenges battery joining technologies by requiring higher energy density both by mass and volume. Improving the energy density via new battery chemistry would be the holy grail but is seriously hindered and progresses slowly. In the meantime, alternative ways, such as implementing more efficient cell packaging by minimizing the electrical resistance of joints are of primary focus. In this paper we discuss the challenges associated with the electrical characterisation of laser soldered joints in general, and the minimization of their resistive losses, in particular. In order to assess the impact of the joint resistance on the overall resistance of the sample, the alteration in resistance was monitored as a function of voltage probe distance and modelled by finite element simulation. The experimental measurements showed two different regimes: one far from of the joint area and another in its vicinity and within the joints cross section. The presented results confirm the importance of the thickness of the filler material, the effective and the total soldered area, and the area and the position of the voids within the total soldered area in determining the electrical resistance of joints.

A challenge in building large-scale superconducting quantum processors is the precise control and manipulation of the qubit state. However, the crosstalk between the microwave control lines impedes the parallel execution of high-fidelity digital and analog quantum operations. Here, we propose and demonstrate a universal compensation protocol for calibrating the microwave signal crosstalk. We also introduce amplified error sequences to optimize the accuracy. Furthermore, we show a definitive improvement in parallel gate operations with crosstalk cancellation, demonstrating the technique's effectiveness. This work paves the way for superconducting hardware that features automated calibration of microwave crosstalk, leading to enhanced fidelities in multiqubit circuits.

We propose and experimentally realize a scheme of the optical nonreciprocity (ONR) using degenerate two-level atoms embedded in an optical ring cavity. For the degenerate transition Fg=4→Fe=3, we first study the cavity-transmission property in different coupling field, and verify that within the strong-coupling regime, the single-dark-state peak formed by electromagnetically induced transparency (EIT) shows ONR. Qualitative theoretical analysis shows that the stable ground-state Zeeman coherence is necessary for intracavity EIT. However, due to the frequency degeneracy, the large Rabi frequency of counter-propagating coupling field can reduce the number of effective atoms and weaken the strong-coupling of the atom-cavity, which determines that ONR based on intracavity EIT occurs only at weaker probe intensity. Furthermore, the ONR transmission with high contrast, linewidth-narrowed and broadband is experimentally demonstrated.

Quantum cryptography revolutionizes secure information transfer, providing defense against both quantum and classical computational attacks. The primary challenge in extending the reach of quantum communication comes from the exponential decay of signals over long distances. Addressing this challenge, we have developed Quantum-protected Control-based Key Distribution (QCKD), overcoming transmission range limitations by monitoring signal leakages and rendering leaked quantum states significantly non-orthogonal. This paper reports on the experiments with the QCKD, conducted over a 1,707 km fiber line. We demonstrate advancements in critical components of the protocol, showing its remarkable scalability and adaptability for extended distances and multi-user configurations.

The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

The Aether Physics Model (APM) presents a radical reinterpretation of fundamental physics, offering potential solutions to long-standing problems in Quantum Mechanics and General Relativity. This paper explores the core concepts and equations of the APM, demonstrating how they provide a unified framework for understanding the nature of space, time, matter, and fundamental forces. We examine the implications of the APM's quantized Aether structure, the role of the Singularity and Gforce, and the reinterpretation of fundamental constants and forces. The model's predictions regarding dark matter, neutron content in stable matter, and the unification of forces are discussed, along with potential experimental tests. Additionally, we introduce the loxodrome concept and toroidal particle topology as central elements in explaining fundamental particles and forces. While highly speculative, the APM offers a thought-provoking alternative to standard physics models and warrants further investigation.

The rapid advancements and the merging of hybrid quantum-classical computing, artificial intelligence (AI), machine learning (ML), and deep learning (DL) pose a potentially unseen and significant threat to encryption that may impact Post-Quantum Cryptography (PQC) transition timelines. There is a direct hybrid quantum-classical computing threat on cryptography, and there is also a direct threat AI/ML on cryptography. However, the synergistic combination of these technologies presents known and unknown threats that need attention, focus action, and research. This paper reviews Grover's Adaptive Search (GAS), which combines Grover's Algorithm with adaptive techniques to optimize search further, potentially making it even more efficient for attacking encryption. This work also examines the quantum-accelerated Harrow-Hassidim-Lloyd (HHL) Algorithm, designed to solve systems of linear equations exponentially faster than classical algorithms in certain conditions. The HHL algorithm can solve some lattice-based problems, which have implications for lattice-based encryption. This technological confluence and its potential impact on cryptography and encryption necessitate a proactive and coordinated approach to developing and implementing quantum-resistant AI/ML cryptographic solutions. This paper reviews the technological confluence and its potential implications for classical cryptography and PQC transition timelines and calls for further research.

Recognition, decoding and tracking of vortex patterns is of increasing importance in many fields reaching from astronomical observation of distant galaxies to turbulence phenomena in liquids or gases. Currently, coherent light beams with orbital angular momentum (OAM) are of particular interest for optical communication, metrology, micro-machining or particle manipulation. One common task is to identify characteristic spiral patterns in pixelated intensity maps at real-world signal-to-noise ratios. Recently, Fast Fourier Transform (FFT) was applied to the quantitative analysis of spiral interference patterns of OAM beams. Our study considers this approach in more detail. It is demonstrated that specific information can be extracted by combining conformal mapping by polar transform with determining one- or two-dimensional angular frequency spectra either in spatially fixed or scanning mode. Results of proof-of-principle experiments are presented.

We study Einstein's gravity coupled to nonlinear electrodynamics with two parameters in Anti-de Sitter spacetime. Magnetically charged black holes in an extended phase space is investigated. We obtain the mass and metric functions, their asymptotic and corrections to the Reissner--Nordstr\"{o}m metric function when the cosmological constant vanishes. The first law of black hole thermodynamics in extended phase space is formulated and the magnetic potential and the thermodynamic conjugate to the coupling are obtained. We proved the generalized Smarr relation. The heat capacity and the Gibbs free energy are computed and phase transitions are studied. It was shown that the electric field of charged objects at the origin and electrostatic self-energy are finite within the nonlinear electrodynamics proposed.

Owing to the nondiffracting, self-accelerating, and self-healing properties, Airy beams of different nature have become a subject of immense interest in the past decade. Their interesting properties have opened doors to many diverse applications. Consequently, the questions of how to properly design spatial manipulation of Airy beams or how to implement them in different setups have become important and timely in the development of various optical devices. Here, based on our previous work, we present a short review on the spatial control of Airy beams, including the interactions of Airy beams in nonlinear media, beam propagation in harmonic potential, and the dynamics of abruptly autofocusing Airy beams in the presence of a dynamic linear potential. We demonstrate that under the guidance of nonlinearity and external potential, the trajectory, acceleration, structure, and even the basic properties of Airy beams can be adjusted to suit specific needs. We describe other fascinating phenomena observed with Airy beams, such as self-Fourier transformation, periodic inversion of Airy beams, and the appearance of spatial solitons in the presence of nonlinearity. These results have promoted the development of Airy beams, and have been utilized in various applications, including particle manipulation, self-trapping, and electronic matter waves.

Quantum computing is tipped to lead the future of global technological progress. However, the obstacles related to quantum software development are an actual challenge to overcome. In this scenario, this work presents an implementation of the quantum search algorithm in Atos Quantum Assembly Language (AQASM) using the quantum software stack my Quantum Learning Machine (myQLM). We present the creation of a virtual quantum processor whose configurable architecture allows the analysis of induced quantum noise effects on the quantum algorithms. The codes are available throughout the manuscript so that readers can replicate them and apply the methods discussed in this article to solve their own quantum computing projects. The presented results are consistent with theoretical predictions and demonstrate that AQASM and myQLM are powerful tools for building, implementing, and simulating quantum hardware.

In this paper, we introduce a novel controlled quantum communication protocol utilizing a quantum random walk involving one sender, one receiver, and multiple controllers. Inspired by classical random walk theory, quantum random walk serves as the foundation of our proposed protocol. With this protocol, we demonstrate the ability to transfer any n- dimensional quantum state to any party facilitated by any m number of controllers. Furthermore, any of the (m+1) individuals has the freedom to accept the role of the receiver. Rigorous testing of the protocol’s performance is conducted through quantum state tomography. We have run different variations of the circuits in IBMQ QASM simulator. Additionally, we explore the effectiveness of a weak measurement-based protocol designed to mitigate amplitude-damping noise’s detrimental effects on quantum states. By analyzing fidelity versus amplitude damping noise-strength plots for scenarios with and without the weak measurement protocol, we provide valuable insights into its protective capabilities across various levels of noise. These find- ings illuminate the protocol’s potential applications in quantum information processing

Due to the extraordinary mechanical properties of ultra-high-performance concrete (UHPC), the shear stirrups in UHPC beams could potentially be removed. The aim of this study is to determine the effect of beam height and steel fiber volume content on the shear behavior of non-stirrup UHPC beams under a larger shear span-depth ratio (up to 2.8). Eight beams were designed and fabricated, including six non-stirrup UHPC beams and two comparing stirrup-reinforced normal concrete (NC) beams. The experimental results demonstrated that the volume content of steel fiber could be a crucial factor affecting the ductility, cracking strength, and shear strength of non-stirrup UHPC beams and altering their failure modes. Additionally, the height of the beam had a considerable effect on its shear resistance. This study revealed that the French standard formulae were more accurate for the UHPC beams with larger shear span-depth ratios and PCI-2021 formulae greatly overestimate the shear capacity of UHPC beams with larger shear span-depth ratios. Xu’s formulae were more accurate for the steel fiber-reinforced UHPC beams with larger shear span-depth ratios.

The equation of state of asymmetric nuclear matter as well as the neutron and proton effective masses and their partial-wave and spin-isospin decomposition are analyzed within the Brueckner–Hartree–Fock approach. Theoretical uncertainties for all these quantities are estimated by using several phase-shift-equivalent nucleon-nucleon forces together with two types of three-nucleon forces, phenomenological and microscopic. It is shown that the choice of the three-nucleon force plays an important role above saturation density, leading to different density dependencies of the energy per particle. These results are compared to the standard form of the Skyrme energy-density functional and we find that it is not possible to reproduce the BHF predictions in the (S,T) channels in symmetric and neutron matter above saturation density, already at the level of the two-body interaction, and even more including the three-body interaction.

Large-span post-tensioned (PT) beams play a crucial role in maximizing the benefits of post-tensioning techniques. Bonded and unbonded systems are prevalent, with the latter being more widespread in the United States. While bonded systems are advantageous for creating long spans when multiple tendons are grouped in ducts, limited literature exists on their demolition. In a case study, this paper addresses the unique challenge of demolishing large-span bonded post-tensioned beams due to a building's functional change. Emphasizing insights for engineers, it explores the use of cutting and dismantling methods, considering the presence of prestressed cables. The demolition process is distinctive due to the presence of numerous pre-stressed cables along the beams, necessitating a specialized and cautious cutting approach. This is accomplished through the use of a drilling technique that selectively distresses the tendons, ensuring they are not all affected simultaneously. An intriguing observation discussed in this paper pertains to the occurrence of horizontal cracks accompanied by loud sounds following the drilling process, offering insights from the design perspective of PT systems. The paper details an innovative method for safely demolishing large-span bonded PT beams, using ground-penetrating radar and computer models to navigate structural complexities and ensure nearby structures' safety.

We present a new family of Bessel solutions of the paraxial equation. Such solutions keep their form during propagation due to a quadratic phase factor that makes them scaled propagation invariant fields. The Bessel beams we introduce have the particularity that the topological phase is twice the order of the Bessel function and the argument varies quadratically with the radius

Quantum computing (QC) has opened the door to advancements in machine learning (ML) tasks that are currently implemented in the classical domain. Convolutional neural networks (CNNs) are classical ML architectures that exploit data locality and possess a simpler structure than fully-connected multi-layer perceptrons (MLPs) without compromising the accuracy of classification. However, the concept of preserving data locality is usually overlooked in the existing quantum counterparts of CNNs, particularly for extracting multi-features in multidimensional data. In this paper, we present a multidimensional quantum convolutional classifier (MQCC) that performs multidimensional and multi-feature quantum convolution with average and Euclidean pooling and thus adapting the CNN structure to a variational quantum algorithm (VQA). Average pooling is based on the quantum Haar transform (QHT) and Euclidean pooling is based on partial quantum measurement. The experimental work was conducted using multidimensional data to validate the correctness and demonstrate the scalability of the proposed method utilizing both noisy and noise-free quantum simulations. We evaluated the MQCC model with reference to reported work on state-of-the-art quantum simulators from IBM Quantum and Xanadu using a variety of standard ML datasets. The experimental results showed favorable characteristics of our proposed techniques compared to existing work with respect to a number of quantitative metrics such as the number of training parameters, cross-entropy loss, classification accuracy, circuit depth, and quantum gate count.

Quantum correlations, especially time correlations, are crucial in ghost imaging in order to significantly reduce the background noise on the one hand while increasing the imaging resolution. Moreover, the time correlations serve as a critical reference, distinguishing between signal and noise, which in turn enable clear visualization of biological samples. Quantum imaging also addresses the challenge involved in imaging delicate biological structures with minimal photon exposure and sample damage. Here we explore the recent progress in quantum correlation-based imaging, notably its impact on secure imaging and remote sensing protocols as well as on biological imaging. We also exploit the quantum characteristics of heralded single-photon sources (HSPS) combined with decoy-state methods for secure imaging. This method uses Quantum Key Distribution (QKD) principles to reduce measurement uncertainties and protect data integrity. It is highly effective in low-photon-number regimes for producing high-quality, noise-reduced images. The versatility of decoy-state methods with WCSs (WCS) is also discussed, highlighting their suitability for scenarios requiring higher photon numbers. We emphasize the dual advantages of these techniques: improving image quality through noise reduction and enhancing data security with quantum encryption, suggesting significant potential for quantum imaging in various applications, from delicate biological imaging to secure quantum communication.

In this study, based on a new quantum integral identity, the authors establish some quantum estimates of Hermite-Hadamard type inequalities for convex functions. These results generalize and improve some known results given in literatures.

We study the electron tunneling (ET) and local Andreev reflection (AR) processes in a quantum dot (QD) coupled to the left and right ferromagnetic leads with noncollinear ferromagnetisms. In particular, we consider that the QD is also side-coupled to a nanowire hosting Majorana bound states (MBSs) at its ends. Our results show that when one mode of the MBSs is coupled simultaneously to both spin-up and spin-down electrons on the QD, the height of the central peak is quite different from that if the MBS is coupled to only one spin component electrons. The ET and AR conductances which are mediated by the dot-MBS hybridization strongly depend on the angle between the left and right magnetic moments in the leads, which result in sign change of the angle-dependent tunnel magnetic resistance. This result is very different from case when the QD is coupled to regular fermonic mode, and can be used for detecting the existence of MBSs, a current challenge in condensed matter physics under extensive investigations.

Thermal camouflage is a highly sought-after technology to increase the survivability of military equipment against infrared (IR) detectors. Recently, two-dimensional (2D) nanomaterials have shown low IR emissivity, widely tunable opto-electronic properties and compatibility with stealth-applications. Among them, graphene and graphene-like materials are the most attractive 2D materials used for thermal camouflage applications. In particular, in multilayer graphene (MLG) charge density can be effectively tuned through sufficiently intense electric fields or through electrolytic gating. Therefore, MLG optical properties, like infrared emissivity and absorbance, can be controlled in a wide range by voltage bias. The large emissivity modulation achievable with this material makes it suitable in the design of thermal dynamic camouflage devices. Generally, the emissivity modulation in the multilayered graphene medium is governed by an intercalation process of non-volatile ionic liquids under a voltage bias. The electrically-driven reduction of emissivity leads to a decrease in the apparent temperature of the surface, which can match that of the background enabling thermal camouflaging. Since this property is common to other graphene-based materials, here we present a review specifically focused on the recent advances in the field of the thermal camouflage properties of graphene in the form of composite film and aerogel structures. A summary of the current understanding of the working principle of thermal camouflage materials, current limitations, and future opportunities is presented and discussed.

We introduce optically clear and resilient free-form micro-optical of pure (non-photosensitized) organic-inorganic SZ2080 material made by femtosecond 3D laser lithography (3DLL). This is advantageous for rapid printing of 3D micro-/nanooptics, including their integration directly onto optical fibers. A systematic study on the fabrication peculiarities and quality of resultant structures is performed. Comparison of microlenses’ resiliency to CW and femtosecond pulsed exposure is determined. Experimental results prove that pure SZ2080 is ∼3 fold more resistant to high irradiance as compared with a standard photo-sensitized material and can sustain up to 1.91 GW/cm² intensity. 3DLL is a promising manufacturing approach for high-intensity micro-optics for emerging fields in astro-photonics and atto-second pulse generation. Additionally, pyrolysis is employed to shrink structures up to 40% by removing organic SZ2080 constituents. This opens a promising route towards downscaling photonic lattices and creation of mechanically robust glass-ceramic structures.

Quantum-dot cellular automata (QCA) is an emerging transistor-less field-coupled nanocomputing (FCN) approach to ultra-scale ‘nanochip’ integration. In QCA, to represent digital circuitry, electrostatic repulsion between electrons and the mechanism of electron tunnelling in quantum dots are used. QCA technology can surpass conventional complementary metal-oxide semiconductor (CMOS) technology in terms of clock speed, reduced occupied chip area, and energy efficiency. To develop QCA circuits, irreversible majority gates are typically used as the primary components. Recently, some studies have introduced reversible design techniques, using reversible majority gates as the main building block, to develop ultra-energy efficient QCA circuits. However, this approach resulted in time delays, an increase in the number of QCA cells used, and an increase in the chip area occupied. This work introduces a novel hybrid design strategy employing QCA irreversible, reversible, and partially reversible gates to establish an optimal balance between power consumption, delay time, and occupied area. The hybrid technique allows the designer to have more control over the circuit characteristics to meet different system needs. A combination of reversible, irreversible, and innovative partially reversible majority gates is used in the proposed hybrid design method. We have evaluated the hybrid design method by examining the half-adder circuit as a case study. We have developed four hybrid QCA half-adder circuits, each of which simultaneously incorporates various types of majority gates. The QCADesigner-E 2.2 simulation tool was used to simulate the performance and energy efficiency of the half-adders. This tool provides numerical results for the circuit input/output response and heat dissipation at the physical level, within a microscopic quantum mechanical model.

RNA transcripts play a crucial role as witnesses of gene expression health. Identifying disruptive short sequences in RNA transcription and regulation is essential for potentially treating diseases. Let’s delve into the mathematical intricacies of these sequences. We’ve previously devised a mathematical approach for defining a “healthy” sequence (10.14218/GE.2023.00079). This sequence is characterized by having at most four distinct nucleotides (denoted as nt≤4). It serves as the generator of a group denoted as fp. The desired properties of this sequence are as follows: fp should be close to a free group of rank nt−1, it must be aperiodic, fp should not have isolated singularities within its SL2(C) character variety (specifically within the corresponding Groebner basis). Now, let’s explore the concept of singularities. There are cubic surfaces associated with the character variety of a four-punctured sphere denoted as S24. When we encounter these singularities, we find ourselves dealing with some algebraic solutions of a dynamical second-order differential (and transcendental) equation known as the Painlevé VI equation (10.3390/dynamics4010001). In certain cases, S24 degenerates, in the sense that two punctures collapse, resulting in a “wild” dynamics governed by the Painlevé equations of an index lower than VI. In our paper, we provide examples of these fascinating mathematical structures within the context of miRNAs. Specifically, we find a clear relationship between decorated character varieties of Painlevé equations and the character variety calculated from the seed of oncomirs. These findings should find applications in cancer research.

In the current era of emerging technologies and cutting-edge inventions, it is equally important to consider the ethical aspects of research and innovations to have an ethical space for the sustainable progress and safety of humanity. The field of nanotechnology research and innovation often faces criticism due to its potential adverse impacts on health, the environment, limited accessibility, high costs, and concerns about data privacy. Therefore, it is crucial to address and resolve these ethical issues systematically. In this regard, we present our findings and methods for exploring the application of the ethics technology assessment method by considering its relevance at different stages of innovation development. Specifically, the present work provides a conceptual framework for ethics technology assessment focused on evaluating a significant innovation in nanotechnology within the domain of food safety with specific reference to mycotoxin remediation. By leveraging the value-sensitive design approach, we described various strategies for analyzing the ethical implications of nanotechnology-based innovations in mycotoxin remediation. Through comprehensive ethics technology assessment, nanotechnology-based innovations can be guided toward becoming more value-oriented, thereby making substantial contributions to social progress.

The question of what generates conscious experience has mesmerized thinkers since the dawn of humanity, yet its origins remain a mystery. The topic of consciousness has gained traction in recent years, thanks to the development of large language models that now arguably pass the Turing test, an operational test for intelligence. However, intelligence and consciousness are not related in obvious ways, as anyone who suffers from a bad toothache can attest - pain generates intense feelings and absorbs all our conscious awareness yet nothing particularly intelligent is going on. Still, in the hard sciences, this topic is frequently met with skepticism because to date no protocol to measure the content or intensity of conscious experiences in an observer-independent manner has been agreed upon. Here we present a novel proposal: Conscious experience arises whenever a quantum mechanical superposition forms. Our proposal has several implications: First, it suggests that the structure of the superposition determines the qualia of the experience. Second, quantum entanglement naturally solves the binding problem, ensuring the unity of phenomenal experience. Finally, a moment of agency may coincide with the formation of a superposition state. We outline a research program to experimentally test our conjecture via a sequence of quantum biology experiments. Applying these ideas opens up the possibility of expanding human experience through brain-quantum computer interfaces.

The insufficient toughness of concrete can lead to the occurrence of crack expansion, ultimately resulting in a decline in the physical and mechanical properties such as bearing capacity and deformation characteristics of structural components. In severe cases, this may lead to brittle failure, where the entire structure and system fail suddenly without significant deformation after being stressed. Additionally, during the process of shear and bending failure of reinforced concrete beams, the cracks generated on the side of the beam are mostly I-II composite cracks. Considering the material nonlinearity and geometric irregularity of reinforced concrete, it is of great significance to study the dynamic evolution law of crack expansion in reinforced concrete members. Based on experimental data, this paper aims to utilize the nonlinear finite element simulation software Abaqus to conduct finite element simulations of crack expansion in simple supported reinforced concrete beams. By accurately controlling the constitutive curves of concrete and reinforcement materials, the design of seismic performance of structural members can be enhanced, thereby making essential contributions to the preliminary analysis of actual crack control engineering. The nonlinear finite element results indicate that the joint cracks of the frame with the floor slab primarily manifest as flexural cracks, with the concrete damage degree of the floor slab being higher than that of the beam. This finding underscores the importance of considering the behavior of concrete and reinforcement materials in designing for seismic performance and crack control in actual engineering applications.

Quantum nonlocality represents correlation properties between subsystems of a composite quantum system, usually including the four types: Bell nonlocality, steerability, entanglement, and quantum correlation (quantum discord). Given a basis $e_{AB}=\{|e_{ij}\>\}_{i\in[d_A],j\in[d_B]}$ for the Hilbert space $\H_A\otimes \H_B$ of a bipartite system $AB$, a density operator $\rho^{AB}$ (quantum state) of $AB$ can be represented as a $d_Ad_B\times d_Ad_B$ matrix $\hat{\rho}_{e_{AB}}=[\]$, called the density matrix of a density operator $\rho^{AB}$. A natural question is what is the relationship between the quantum nonlocality of a density operator $\rho^{AB}$ and its corresponding density matrix $\hat{\rho}_{e_{AB}}$? In this work, we discuss the relationships between quantum locality and basis, and prove that one type of quantum locality of density operators and that of their density matrices under a basis are the same if and only if the chosen basis is the tensor product of the bases of subsystems. Consequently, different bases define different quantum nonlocality density operators.

In recent years, advancements in brain science and neuroscience have significantly influenced the field of computer science, particularly in the domain of reinforcement learning (RL). Drawing insights from neurobiology and neuropsychology, researchers have leveraged these findings to develop novel mechanisms for understanding intelligent decision-making processes in the brain. Concurrently, the emergence of quantum computing has opened new frontiers in artificial intelligence, leading to the development of quantum machine learning (QML). This study introduces a novel model that integrates Quantum Spiking Neural Networks (QSNN) and Quantum Long Short-Term Memory (QLSTM) architectures, inspired by the complex workings of the human brain. Specifically designed for reinforcement learning tasks in energy-efficient environments, our approach progresses through two distinct stages mirroring sensory and memory systems. In the initial stage, analogous to the brain’s hypothalamus, low-level information is extracted to emulate sensory data processing patterns. Subsequently, resembling the hippocampus, this information is processed at a higher level, capturing and memorizing correlated patterns. We conduct a comparative analysis of our model against existing quantum models such as Quantum Neural Networks and their classical counterparts, elucidating its unique contributions. Through empirical results, we aim to underscore the effectiveness of our approach in optimizing energy consumption in practical scenarios.

This article proposes an interferometer which should in principle split further an initially split beam to yield new sets of beams, effectively multiplying the number of beams that can be subjected to detectable interference. It can be considered a modification to the Michelson interferometer that introduces additional arrays of beam splitters, mirrors and detectors. It is expected of the interferometer to provide us with a set or sets of data holding details of phase changes in multiple interference patterns detectable by multiple detectors, enabling comparative analysis of data for multiple interference patterns recorded from a single measurement or activity. The number of multiplied beams possible is not limited, as it only depends on the specific amount of beam splitters required for certain experiments and practicals. The interference of multiple beams may improve sensitivity and detection for instrumentation purposes. The use of multiplied beam interferometry may also extend to quantum computation, particularly in linear optical quantum computation scheme as it enable production of multiple coherent beams which may exhibit properties of entanglement, making it suitable for developing optical multi-qubit systems.

This paper draws upon the theory of turbulence in physics to explore the similarities and differences between volatility in financial markets and turbulent phenomena at a statistical physics level. By analogizing the dynamics of financial markets with fluid turbulence, we have developed an innovative analytical framework aimed at deepening the understanding of the complexity inherent in financial markets. Our research methodology includes a comparative analysis of simulated time series data for the Standard & Poor's 500 Index and fully developed turbulent velocity time series. We focus on the similarities in key statistical physical properties, including probability distributions, correlation structures, and power spectral densities. Furthermore, we have established a model of capital flow in financial markets and proposed corresponding solutions. Through computational simulations and data analysis, we find that while financial market volatility shares some statistical characteristics with turbulent phenomena, significant differences exist in the shapes of probability distributions and the temporal scales of correlations. This suggests that although financial markets exhibit patterns akin to turbulence, the behavior of this complex, multi-variable driven system does not completely correspond to natural turbulence, highlighting the limitations of directly applying turbulence theory to financial market analysis. Our study offers a new perspective for the theories of financial markets and the field of econophysics, providing fresh insights into the complexity of financial markets and contributing to the prevention and management of financial risk.

In order to properly cover different scenarios, radiation patterns of antennas should be accordingly adjusted before fabrication. However, most antennas are unable to provide both broadside beam and designable conical beam which are usually-used radiation patterns for radio coverage. In this paper, a planar Circular Polarized (CP) annular Leaky-Wave Antenna (LWA) with conical beam is proposed, which is realized on annular Substrate-Integrated Waveguide (SIW). Broadside beam or conical beam could be easily obtained by fabricating the LWA with modified structural parameters. The central operating band is 5.8 GHz. The LWA allows only the -1th spatial harmonic to radiate, while the fundamental wave and other spatial harmonics are suppressed in slow wave mode. In order to validate the design effectiveness, two examples for broadside beam and conical beam radiation are fabricated and measured. The measurement results show good agreement with the simulation results. The proposed LWA presents a promising radiation performance and is a good candidate for wireless communication applications.

The discovery of the quantum tunnelling effect---the transmission of particles through a high potential barrier---was one of the most impressive achievements of quantum mechanics made in the 1920s. Responding to the contemporary challenges, I introduce a novel deep neural network (DNN) architecture that processes information using the effect of quantum tunnelling. I demonstrate the ability of the quantum tunnelling DNN (QT-DNN) to recognise optical illusions like a human. Hardware implementation of QT-DNN is expected to result in an inexpensive and energy-efficient neuromorphic chip suitable for applications in autonomous vehicles. The optical illusions recognition tests developed in this paper should lay foundations for cognitive benchmarking tasks for AI systems of the future, benefiting the fields of sociophysics and behavioural science.

On 17 October 1947, Niels Bohr was made a knight of the Order of the Elephant by the King of Denmark in view of his outstanding achievements and contributions to science. Bohr designed his own coat of arms that featured a pattern of Yin and Yang (Tai Chi symbol) to symbolize the wave-particle complementarity. However, Bohr’s Yin-Yang diagram (YYD) was neither drawn based on the principles of quantum mechanics, nor did it originate from the traditional Taoist YYD. Scientists still have doubts about the legitimacy of using YYD as the icon of the wave-particle complementarity, because the YYD belonging to quantum mechanics itself is unknown so far. This article reports the YYDs existing in quantum mechanics and justifies the role of YYD in the wave-particle duality by showing that any system, whether classical or quantum, has an ideal YYD as long as it satisfies Bohr’s principle of complementarity (BPC). The deviation of a deformed YYD from the ideal YYD indicates the extent to which a real system satisfies BPC. This article constructs the quantum YYD by the complex quantum trajectory of a particle tunneling via a step barrier, which displays the continuous transition between the wave behavior and the particle behavior. It appears that the YYD designed by Bohr in his coat of arms resembles the YYD generated by tunneling motion, not only in appearance but also in the governing equation.

Continuum robots play the role of end-effector in various surgical robots and endoscopic devices. The robots may be categorized as rigid or soft continuum robots (SCRs). While the SCRs have proven advantages such as safety and compliance, more research and development are required to enhance their capability for specific medical scenarios. This research aims at designing a soft robot considering concepts of geometric and kinematic similarities. The chosen application is a semi-invasive medical application known as Transesophageal Echocardiography (TEE), but the methodology can be implemented in other similar applications. Since established rigid carrier construction make use of principles we find as well embodied in vertebral spines, the paragon for soft robot solution can be the phylogenetic precursor of the spine, the Chorda dorsalis. The feasibility of fabrication of a soft endoscopic device derived from that paragon within a robotics laboratory was shown empirically by producing a three-segment pneumatic SCR. The kinematic model was proposed based on the method of transformation matrices, and an algorithm based on a self-organizing map (SOM) was proposed and applied to realize kinematic similarity. The simulation results indicate that the algorithm acting as an open-loop controller forces the soft robot tip to follow the desired path which in this case is the path of the rigid probe. It is concluded that the solution provides a soft robot that can surrogate and succeed the traditional rigid counterpart owing to size, workspace, and kinematics.

We study theoretically the Josephson diode effect (JDE) realized in a system composed of parallel-coupled double quantum dots (DQDs) sandwiched between two semiconductor nanowires deposited on an s-wave superconductor surface. Due to the combined effects of the proximity-caused superconductivity, strong Rashba spin-orbit interaction and Zeeman splitting inside the nanowires, a pair of Majorana bound states (MBSs) may possibly emerge at opposite ends of each nanowire. Different phase factors arisen from the superconductor substrate can be generated in the coupling amplitudes between the DQDs and MBSs prepared at the left and right nanowires, and will result in the Josephson current. We find that the critical Josephson currents in positive and negative directions are different from each other in amplitude within an oscillation period with respective to the magnetic flux penetrating through the system, a phenomenon known as the JDE. It arises from the quantum interference effect in this double-path device, and can hardly occur in system of one QD coupled to MBSs. Our results also show that the diode efficiency can reach up to 50%, and depends on the overlap amplitude between the MBSs and the energy levels of the DQDs adjustable by gate voltages. The present model is realizable within current nanofabitication technologies and may find practical use in interdisciplinary field of Majorana and Josephson physics.

Artificial intelligence (AI) systems of autonomous systems such as drones, robots and self-driving cars may consume up to 50% of total power available onboard, thereby limiting the vehicle’s range of functions and considerably reducing the distance the vehicle can travel on a single charge. Next-generation onboard AI systems need an even higher power since they collect and process even larger amounts of data in real time. This problem cannot be solved using the traditional computing devices since they become more and more power-consuming. In this review article, we discuss the perspectives of development of onboard neuromorphic computers that mimic the operation of a biological brain using nonlinear-dynamical properties of natural physical environments surrounding autonomous vehicles. Previous research also demonstrated that quantum neuromorphic processors (QNPs) can conduct computations with the efficiency of a standard computer while consuming less than 1% of the onboard battery power. Since QNPs is a semi-classical technology, their technical simplicity and low, compared with quantum computers, cost make them ideally suitable for application in autonomous AI system. Providing a perspective view on the future progress in unconventional physical reservoir computing and surveying the outcomes of more than 200 interdisciplinary research works, this article will be of interest to a broad readership, including both students and experts in the fields of physics, engineering, quantum technologies and computing.

We present a compact polarimeter for 3He ions with special emphasis on the analysis of short-pulsed beams accelerated during laser-plasma interactions. We discuss the specific boundary conditions for the polarimeter, such as the properties of laser-driven ion beams, the selection of the polarization-sensitive reaction in the polarimeter, the representation of the analyzing-power contour map, the choice of the detector material used for particle identification, as well as the production procedure of the required deuterated foil-targets. The assembled polarimeter has been tested using a tandem accelerator delivering unpolarized 3He ion beams, demonstrating good performance in the few-MeV range. The statistical accuracy and the deduced figure-of-merit of the polarimetry are discussed, including the count-rate requirement and the lower limit of accuracy for beam-polarization measurements at a laser-based ion source.

Renovation, restoration, remodeling, refurbishment, and retrofitting of build-ings often imply modifying the behavior of the structural system. Modification sometimes includes applying forces (i.e., concentrated loads) to beams that before were subjected to distributed loads only. For a reinforced concrete structure, the new condition causes a beam to bear a concentrated load with the crack pattern that was produced by the distributed loads that acted in the past. If the concentrated load is applied at or near the beam’s midspan, the new shear demand reaches the maximum around the midspan. But around the midspan, the cracks are vertical or quasi-vertical, and no inclined bar is present. So, the actual shear capacity around the midspan not only is low, but also can be substantially lower than the new demand. In order to bring the beam capacity up to the demand, fiber-reinforced-polymer composites can be used. This paper presents a design method to increase the concentrated load-carrying capacity of reinforced concrete beams whose load distribution has to be changed from distributed to concentrated, and an analytical model to pre-dict the concentrated load-carrying capacity of a beam in the strengthened state.

Investigations into the properties of generalized effective temperature are conducted across arbitrary dimensions. Maxwell-Boltzmann distribution is displayed for one, two, and three dimensions, with effective temperatures expressed for each dimension. The energy density of blackbody radiation is examined as a function of dimensionality. Effective temperatures for non-uniform temperature distributions in one, two, three, and higher dimensions are presented, with generalizations extended to arbitrary dimensions. Furthermore, the application of generalized effective temperature is explored not only for linearly non-uniform temperature distributions but also for scenarios involving the volume fraction of two distinct temperature distributions. Finally, the effective temperature is determined for a cryogenic system supplied with both liquid nitrogen and liquid helium.

This study explores the properties and behavior of bi-close-to-convex functions, introducing new subclasses defined by their relationship with fractional differential operator and bi-univalent functions. Using the Faber polynomial technique, we derive upper bounds for the n^{th} coefficient of functions in these classes. We also investigate the erratic behavior of initial coefficients in bi-close-to-convex functions, as characterized by the (λ,q)-fractional differintegral operator. Furthermore, we address Fekete-Szegö problems and present notable findings from our investigation, contributing to the continued growth and refinement of geometric function theory, yielding new insights and practical uses.

1) We shall discuss what modern interpretations say about the Heisenberg's uncertainties. These interpretations explain that a quantity begins to 'lose' meaning when a conjugate property begins to 'acquire' definite meaning. We know that a quantity losing meaning means that it has no fixed value and has an uncertainty . In this paper we look deeper into this interpretation and the outcome reveals more evidence of the quantity losing meaning. Newer insights appear. 2) We consider two extreme cases of hypothetical processes nature undergoes, without interference by a measurement: One, a system collapses to an energy eigenstate under the influence of a Hamiltonian instantaneously at a time $t$. This is thus what would happen if we would measure the system's energy. Next, when a particle becomes localised to a point at a time $t_0$ under the influence of a Hamiltonian. This is thus what would happen if we would measure the system's position. We shall prove that both these situations cannot arise under ordinary circumstances and thus measurement processes cannot be modelled by physical Hamiltonians.

This paper presents the results of the experimental research and numerical analysis of three reinforced concrete deep beams with openings, designed by the Strut-and-Tie method according to the EN 1992-1-1 recommendations. All tested specimens were made in full size, with the same geometric characteristics and quality of the materials. The specimens, constructed as simply supported beams, were loaded with two concentrated forces and were tested for bending until failure. Each specimen was reinforced with different reinforcement layout determined by parameter variation within the Strut-and-Tie method. Based on the results of experimental research, it was concluded that the behavior of loaded members was in agreement with the proposed forms of the Strut-and-Tie models that were used for their design.

The investigation on the issue of damage diagnosis based on strain modal parameters is conducted in this paper using simply supported wooden Beams as the study's object. First, ABAQUS is utilized to create finite element models of intact wooden beams as well as wooden beams with varying degrees of damage and perform modal analyses on them. Next, damage identification studies are conducted on the wooden beam structure using various strain modal parameters (strain mode strain modal difference, strain modal curvature difference), the timber beam damage identification test then yields the modal parameters of timber beams under various damage situations, and the test findings are contrasted with those of the numerical simulation. The outcomes demonstrate that the damage identification of the test data using the three types of damage identification indexes is consistent with the results of the numerical simulation; the three types of damage identification indexes can locate the damage to timber beams, but the identification effect of the indexes is different, the best-recognized metric is the strain mode curvature difference; the next best is the strain mode difference, and the worst is the strain modes. The study's findings can serve as a guide for future damage detection on wood beams.

The increasing popularity of carbon-reinforced concrete (CRC) is attributed to its exceptional tensile properties, low density, no corrosion phenomenon, and remarkable flexibility, allowing it to be easily shaped into various forms. This research investigates the feasibility of using a special 2D Netzgitterträger (NetzGT) reinforcement system, featuring a net-shaped fabricated textile made of multiple diagonally offset rovings with overlapping edge strands, as a viable alternative to traditional steel reinforcement in concrete beams. This reinforcement is manufactured from carbon rovings with three different diagonal angles of 50⁰, 60⁰, and 70⁰ respectively. Laboratory experiments were conducted to assess the mechanical behavior of beams reinforced with the 2D NetzGT reinforcement. Bending and shear tests were performed on beams with varying numbers of overlapped edge roving and roving angles to evaluate the tensile capacity and failure characteristics of beams. The increase in the number of overlapped edge rovings led to a noticeable increase in the maximum tensile force. Tensile tests on strands were also performed with the increasing number of overlapped rovings to analyze their tensile strength. Additionally, single yarn pull-out tests were also conducted to examine the influence of the roving angle on the bond strength between the carbon textile roving and the concrete matrix

In the present trend of constructing taller and longer structures, the application of lightweight aggregate concrete is becoming an increasing important advanced solution in the modern construction industry. In engineering practice, the analysis of lightweight concrete elements is performed using the same algorithms used for normal concrete elements. As an alternative to traditional engineering methods, nonlinear numerical algorithms based on constitutive material models may be used. The paper presents a comparative analysis of curvature calculations for flexural lightweight concrete elements, incorporating analytical code methods EN 1992-1 and ACI 318-14, as well as a numerical analysis using the constitutive model of cracked tensile lightweight concrete recently proposed by the authors. To evaluate the adequacy of the theoretical predictions, experimental data of 51 lightweight concrete beams tested during five different programmes were collected. A comparison of theoretical and experimental results showed that the most accurate predictions are obtained using numerical analysis and the constitutive model proposed by the authors. In the future, the latter algorithm can be used as a reliable tool for improving the design standard methods or numerical modelling of lightweight concrete elements subjected to short-term loading.

Nearest-neighbour clustering is a simple yet powerful machine learning algorithm that finds natural application in the decoding of signals in classical optical-fibre communication systems. Quantum k-means clustering promises a speed-up over the classical k-means algorithm; however, it has been shown to currently not provide this speed-up for decoding optical-fibre signals due to the embedding of classical data, which introduces inaccuracies and slowdowns. Although still not achieving an exponential speed-up for NISQ implementations, this work proposes the generalised inverse stereographic projection as an improved embedding into the Bloch sphere for quantum distance estimation in k-nearest-neighbour clustering, which allows us to get closer to the classical performance. We also use the generalised inverse stereographic projection to develop an analogous classical clustering algorithm and benchmark its accuracy, runtime and convergence for decoding real-world experimental optical-fibre communication data. This proposed `quantum-inspired' algorithm provides an improvement in both the accuracy and convergence rate with respect to the k-means algorithm. Hence, this work presents two main contributions. Firstly, we propose the general inverse stereographic projection into the Bloch sphere as a better embedding for quantum machine learning algorithms; here, we use the problem of clustering quadrature amplitude modulated optical-fibre signals as an example. Secondly, as a purely classical contribution inspired by the first contribution, we propose and benchmark the use of the general inverse stereographic projection and spherical centroid for clustering optical-fibre signals, showing that optimizing the radius yields a consistent improvement in accuracy and convergence rate.

The practical necessity of strengthening of reinforced concrete structure elements requires a choice of a method which would provide cost-effectiveness, simplicity of construction and durability of the chosen solution. One of the ways is strengthening using the material belonging to the group of micro-reinforced concretes called ferrocement. The paper presents the comparative analysis of some of the results of RC beams exposed mainly to flexure, strengthened with ferrocement elements (strips) applied by gluing on the on the tensed side of RC beams. The results are obtained using the experimental, analytical and numerical research on the adequate models. Strengthening of the beams was performed in the form of four types of ferrocement strips (four different strip widths and four different numbers of wire mesh layers). The numerical non-linear analysis using finite elements method (FEM) was employed, with the introduction of the corresponding characteristics of constitutive material obtained by the experiments on the test specimens. The analytical researches were performed using known analytical calculation methods in order to formulate the model for the calculation of the ultimate and serviceability limit states of the strengthened cross-section. The results presented in the paper, through their comparative compatibility, confirmed the applicability of this strengthening method.

We present the generation and nonlinear frequency conversion of nanosecond cylindrical vector beams (CVBs) in two-mode fiber (TMF). Based on the polarized dependence vector mode coupling characteristic and the precise wavelength tunability of an acoustically-induced fiber grating (AIFG), the nanosecond cylindrical vector beams (CVBs, 1064 nm, 10 ns) is directly generated in a TMF with convenient switching characteristics between the radial and azimuthal vector beams. Furthermore, the stimulated Raman scattering (SRS) is produced based on the transmission of the nanosecond CVBs in the 100-meters long TMF, and the spatial intensity and polarization distributions characteristics the 1st-order Stokes shifted component is consistent with the nanosecond CVBs pump pulse. This work provides a method for achieving wavelength conversion of the CVBs in optical fiber.

The study focuses on the free vibration analysis of beams made of axially functionally graded materials (AFGM) with curvilinear variable cross-sections along their length. The beams encompass various shapes, including concave and convex conic sections, with axial material properties varying according to polynomial and exponential laws. The equations of motion are derived using Hamilton's principle within the framework of Timoshenko beam theory. These governing equations, subjected to various boundary conditions, are solved using the differential transform method (DTM). The proposed solution technique is validated by comparing computed natural frequencies with existing in literature results and those obtained through three-dimensional finite element analysis in ABAQUS. The incorporation of material gradients into the beam finite element models was achieved through the user-defined material subroutine (UMAT). Additionally, a comprehensive study is conducted to examine the influence of various factors on the natural frequencies of functionally graded beams. These factors include parameters of material laws, types of variable beam shapes, slenderness ratio, and specific boundary conditions. This study provides a thorough understanding of the modal dynamics of the considered beams, offering valuable insights into the behavior of FGM structures.

The research object was the stress-strain state of shear stud bonds in the contact joint of steel-concrete beams. The work diagrams for three types of anchors are given. Based on the analysis of numerical and full-scale experiments, analytical dependencies are proposed that reflect the actual operation of anchor ties. Comparisons of the calculation results by analytical formulas and comparisons with numerical and full-scale experiment data are given. Numerical studies have revealed the pattern of the stress-strain state of the contact joint, the stages of development of cracks in the concrete flange, and the sequence of development of deformations in anchor ties. It was revealed that vertical shear studs bonds have an increased bearing capacity, although displacements are 1.5-2 times greater than those of loop-shaped anchor ties.

This paper presents an approach to damage identification in beams by modal curvatures based on the use of beamforming algorithms. These processors have been successfully used in acoustics for the last thirty years to solve the inverse problems encountered in source recognition and image reconstruction, based on ultrasonic waves. In addition, beamformers apply to a broader range of problems in which the forward solutions are computable and measurable, especially regarding the field of structural vibrations, where the use of such estimators has not received attention to date. In this paper, modal curvatures will play the role of the replica vectors of the imaging field. By means of numerical studies and experimental tests on a steel beam, we motivate the choice of modal curvatures as observed quantities. Furthermore, we compare the performance of the Bartlett and minimum variance distortionless beamformers (MVDR) with an estimator based on the simple minimization of the difference between model and measured data. The results suggest that the application of the MVDR beamformer is highly effective, especially in cases of slight damage between two sensors. MVDR enabled both damage localization, and quantification.

In this study, experimental work was carried out on reinforced concrete (RC) beams strengthened with carbon fiber reinforced polymers (CFRP) plates. This study aims to examine the effect of the reinforcement ratio on the flexural behavior of these beams and propose a new model for predicting the debonding moment. Six RC beams consisting of three control beams and three beams strengthened with CFRP plates were tested. The beams were simply supported and loaded with four-point bending. The test variable was the tensile reinforcement ratio (1%, 1.5%, and 2.5%). Analytical prediction using the fiber element method was also carried out to obtain the complete theoretical response of the beam due to flexural loads. The test results show that the reinforcement ratio affected the bending performance of RC beams with CFRP plates. Following this, the experimental data from 60 beam test results from published literature and this study were analyzed. From these data, it was found that the ratio of tensile reinforcement, the ratio of modulus of elasticity of concrete, the modulus of elasticity of the plate, and plate thickness all affect the value of debonding moment. A parametric study using fiber element and two-dimensional finite element method was also carried out to confirm the effect of these parameters on debonding failure. These parameters were then used to develop an equation to predict the debonding moment of RC beams strengthened with CFRP plates using simple statistical analysis. This analysis resulted in a simple model for predicting the debonding moment. Then the model is entered into a computer program, and the complete response of the cross-section due to debonding failure can be obtained.

The simplest elasticity model of foundation underlying a slender beam under flexure was conceived by Winkler, requiring local proportionality between soil reactions and beam deflection. Such an approach leads to well-posed elastostatic and elastodynamic problems, but, as highlighted by Wieghardt, it provides elastic responses which are not technically significant for a wide variety of engineering applications. Thus, Winkler's model was replaced by Wieghardt himself by assuming that the beam deflection is the convolution integral between soil reaction field and an averaging kernel. Due to conflict between constitutive and kinematic compatibility requirements, the corresponding elastic problem of an inflected beam resting on Wieghardt foundation results to be ill-posed. Modifications of the original Wieghardt model were proposed by introducing fictitious boundary concentrated forces of constitutive type, which are physically questionable, being significantly influenced on prescribed kinematic boundary conditions. Inherent difficulties and issues are overcome in the present research using a displacement-driven nonlocal integral strategy got by swapping input and output fields involved in Wieghardt's original formulation. That is, nonlocal soil reaction fields are output of integral convolutions of beam deflection fields with an averaging kernel. Equipping the displacement-driven nonlocal integral law with the bi-exponential averaging kernel, an equivalent nonlocal differential problem, supplemented with non-standard constitutive boundary conditions involving nonlocal soil reactions, is established. As a key implication, the integro-differential equations governing the elastostatic problem of an inflected elastic slender beam resting on displacement-driven nonlocal integral foundation are replaced with much simpler differential equations supplemented with kinematic, static and new constitutive boundary conditions. The proposed nonlocal approach is illustrated by examining and analytically solving exemplar problems of structural engineering. Benchmark solutions for numerical analyses are also detected.

The use of mixed-state ionic beams in collision dynamics investigations is examined. Using high resolution Auger projectile spectroscopy involving He-like ($1s^2\thinspace^1\!S, 1s2s\thinspace^{3,1}\!S$) mixed-state beams, the spectrum contributions of the $1s2s\thinspace^3\!S$ metastable beam component is effectively separated and clearly identified. This is performed with a technique that exploits two independent spectrum measurements under the same collision conditions, but with ions having quite different metastable fractions, judiciously selected by varying the ion beam charge-stripping conditions. Details of the technique are presented together with characteristic examples. In collisions of 4 MeV B$^{3+}$ with H$_2$ targets, the Auger electron spectrum of the separated $1s2s\thinspace^{3}S$ boron beam component allows for a detailed analysis of the formation of the $1s2s(^3\!S)nl \thinspace^2\!L$ states by direct $nl$ transfer. In addition, the production of hollow $2s2p\thinspace^{1,3}\!P$ doubly- and $2s2p^2\thinspace^2\!D$ triply-excited states, by direct excitation and transfer-excitation processes, respectively, can also be independently studied. In similar mixed-state beam collisions of 15 MeV C$^{4+}$ with H$_2$, He, Ne and Ar targets, the contributions of the $1s^2$, $1s2s\thinspace^{3,1}S$ beam components to the formation of the $2s2p\thinspace^{3,1}\!P$ states by double-excitation, $1s\rightarrow2p$ excitation and transfer-loss processes can be clearly identified, facilitating comparisons with theoretical calculations.

This paper discusses the Quantum Temporal Resonator (QTR), a theoretical device leveraging quantum entanglement and metamaterials with negative refraction indices to achieve controlled temporal displacement. By establishing a network of entangled particles within a Bose-Einstein Condensate (BEC) and utilizing a resonant cavity made of advanced metamaterials, the QTR creates localized distortions in space-time. The frequency and amplitude of temporal harmonics within this cavity are finely tuned to allow for precise temporal displacement of matter and information. Numerical simulations demonstrate the coupling between the quantum wave function and electromagnetic fields, validating the theoretical model. The results show distinctive patterns in the wave function and perturbations in the electric field, supporting the feasibility of achieving controlled temporal displacement. This study explores the theoretical framework, mathematical modeling, experimental setup, and potential applications of the QTR, providing a comprehensive analysis of its feasibility and implications.

We discuss the fate of the correspondence principle beyond quantum mechanics, specifically in quantum field theory and quantum gravity, in connection with the intrinsic limitations of the human ability to observe the external world. We conclude that the best correspondence principle is made of unitarity, locality, proper renormalizability (a refinement of strict renormalizability), combined with fundamental local symmetries and the requirement of having a finite number of fields. Quantum gravity is identified in an essentially unique way. The gauge interactions are uniquely identified in form. Instead, the matter sector remains basically unrestricted. The major prediction is the violation of causality at small distances.

In this paper we will show that standard physics to a large degree consists of derivatives of a deeper reality. This means standard physics is both overly complex and also incomplete. Modern physics has typically started from working with first understanding the surface of the world, that is typically the macroscopic world, and then forming theories about the atomic and subatomic world. And we did not have much of a choice, as the subatomic world is very hard to observe directly, if not impossible to observe directly at the deepest level. Despite the enormous success of modern physics, it is therefore no big surprise that we at some point have possibly taken a step in the wrong direction. We will claim that one such step came when one thought that the de Broglie wavelength represented a real matter wavelength. We will claim that the Compton wavelength is the real matter wavelength. Based on such a view we will see that many equations in modern physics are only derivatives of much simpler relations. Second, we will claim that in today’s physics one uses two different mass definitions, one mass definition that is complete or at least more complete, embedded in gravity equations without being aware of it, as it is concealed in GM, and the standard, but incomplete, kg mass definition in non-gravitational physics. First, when this is understood, and one uses the more complete mass definition that is embedded in gravity physics, not only in gravity physics, but in all of physics, then one has a chance to unify gravity and quantum mechanics. Our new theory shows that most physical phenomena when observed over a very short timescale are probabilistic for masses smaller than a Planck mass and dominated by determinism at or above Planck mass size. Our findings have many implications. For example, we show that the Heisenberg uncertainty principle is rooted in a foundation not valid for rest-mass particles, so the Heisenberg uncertainty principle can say nothing about rest-masses. When re-formulated based on a foundation compatible with a new momentum that is also compatible with rest-masses, we obtain a re-defined Heisenberg principle that seems to become a certainty principle in the special case of a Planck mass particle. Furthermore, we show that the Planck mass particle is linked to gravity and that we can easily detect the Planck scale from gravity observations. The Planck mass particle is unique as it only lasts the Planck time, and in that very short time period it can only be observed directly from itself, and it therefore closely linked to absolute rest.

Machine learning (ML) is growing in popularity for various particle accelerator applications including anomaly detection such as faulty beam position monitor or RF fault identification, for non-invasive diagnostics, and for creating surrogate models. ML methods such as neural networks (NN) are useful because they can learn input-output relationships in large complex systems based on large data sets. Once they are trained, methods such as NNs give instant predictions of complex phenomenon, which makes their use as surrogate models especially appealing for speeding up large parameter space searches which otherwise require computationally expensive simulations. However, quickly time varying systems are challenging for ML-based approaches because the actual system dynamics quickly drifts away from the description provided by any fixed data set, degrading the predictive power of any ML method, and limits their applicability for real time feedback control of quickly time-varying accelerator components and beams. In contrast to ML methods, adaptive model-independent feedback algorithms are by design robust to un-modeled changes and disturbances in dynamic systems, but are usually local in nature and susceptible to local extrema. In this work, we propose that the combination of adaptive feedback and machine learning, adaptive machine learning (AML), is a way to combine the global feature learning power of ML methods such as deep neural networks with the robustness of model-independent control. We present an overview of several ML and adaptive control methods, their strengths and limitations, and an overview of AML approaches. A simple code for the adaptive control algorithm used here can be downloaded from: https://github.com/alexscheinker/ES_adaptive_optimization

In this study, three new demountable joints consisting of reinforced concrete columns and steel beams were proposed and their seismic performance was investigated using cyclic loading tests. The test results demonstrated that the three demountable RCS joints had good seismic performance. Using the finite element software ABAQUS, the influence of parameters such as beam flange thickness, bolt strength, and connector steel strength on the seismic performance of each joint was analyzed, and the influence of different parameters on the seismic behavior of the joint was determined. The results also showed that the three demountable RCS joints were sensitive to changes in the thickness of the steel beam flange, while the connector steel strength and bolt type had little impact on the joint's capacity. Additionally, shear capacity calculation formulas for the joint core area provided by different codes and researchers were compared with test and finite element results. The results showed that the calculation results of the ASCE guidance method, the Nishiyama method, and the CECS 347-2013 method were higher than the test values, while the calculation results of the Para method were lower because it did not consider the contribution of the cylindrical steel plate to the shear capacity of the joint core area.

This paper presents a thorough investigation into the shear strength capacity of reinforced concrete deep beams, with a focus on improving predictive accuracy beyond existing code provisions. Analyzing 198 deep beams from 15 investigations, the study considers parameters such as concrete compressive strength (fc’), shear span to effective depth ratio (av/d), and reinforcement ratios (ρs, ρv, ρh ). Introducing a novel predictive model (Equation 7), the study rigorously evaluates it using nonlinear regression analysis and statistical metrics (MAE, RMSE, R2). The proposed model demonstrates a significant reduction in the coefficient of variation (COV) to 27.08%, surpassing existing codes' limitations. Comparative analyses highlight the model's robustness, revealing improved convergence of data points and minimal sensitivity to variations in key parameters. The findings suggest that the proposed model offers enhanced predictive accuracy across diverse scenarios, making it a valuable tool for structural engineers. This research contributes to advancing the understanding of shear strength in reinforced concrete deep beams, offering a reliable and versatile predictive model with implications for refining design methodologies and enhancing the safety and efficiency of structural systems.

Conical emission is a typical nonlinear phenomenon that occurs when the femtosecond laser pulses interact with transparent media. In this work, the conical emission induced by two kinds of typical vortex beams (i.e., Laguerre-Gaussian (LG) and Bessel-Gaussian (BG) beams) in water is experimentally studied. By recording the light spots of different wavelengths on the screen, the characteristics of the conical emission induced by femtosecond vortex beams are studied. It is found that the spots of the supercontinuum induced by the two kinds of vortex beams differ greatly from each other: The spots of the supercontinuum induced by the BG beam are a set of concentric rings like a rainbow with a white center, while the whit light spot in the case of the LG beam are a circular white disk, which is different from the commonly observed white light spots. By measuring the maximum divergence angle, it is observed that the divergence angle increases with the decrease of the wavelength, while the TC merely affects the divergence angle, which is explained from the formation mechanism of conical emission in terms of self-phase modulation. We hope this work can be helpful to the understanding of interaction between the intense laser pulses and matters.

Our research aims to address the urgent need for retrofitting measures to enhance the resilience of damaged coupling beams in real-life scenarios. We conducted a series of tests on scaled-down prototype coupling beams, carefully adhering to similarity theory requirements to ensure accurate representation. The test results showed that the chord rotation capacities of different specimens with the same diagonal bundle varied significantly due to the difference in the confinement levels. The specimens with lower level of confinement were found to have less displacement capacity. When the specimens were strengthened by wrapping with GFRP after damage, it was observed that the increase in confinement level significantly increased the chord rotation capacities of all specimens. In addition, in the tests before the strengthening, the elongation behavior of the specimens is observed until the damage development reaches approximately 2% chord rotation. With the in-crease in chord rotation, the elongation behavior of the specimens stops with increasing damage and then shortening behavior is observed. After retrofitting, it was observed that the axial elongation continued in a limited manner depending on the location and size of the concrete separated from the beam core in the case of collapse before strengthening, and then the beam showed a shortening behavior predominantly. After strengthening studies, our findings contribute valuable insights into the behavior and performance of damaged coupling beams, emphasizing the potential of urgent GFRP wrapping as a viable solution to enhance the seismic resilience of middle- and high-class buildings with structural walls after seismic events.

The literature has well established prestressing in concrete beams and its calculation procedures. However, its use in composite steel-concrete beams has increased despite main normative codes lacking a specific approach for it. Designers must, in most cases, combine the available criteria to calculate the standards of steel and reinforced concrete structures. This study aimed to formulate this optimization problem and analyze CO2 emissions for the optimal design of composite steel-concrete beams with external prestressing. The design variables for the optimization problem include cross-section of laminated or welded profiles, slab height, characteristic strength of concrete to compression, and number of tendons. We obtained a solution for the optimization problem via a genetic algorithm (GA) and a particle swarm optimization one (PSO). Comparative analysis with experimental example and with optimization problem of prestressed steel beam are performed. An parametric analysis to several spams is performed, which enabled to evaluate the factors that most impact CO2 emissions. According to results, the chosen algorithms effectively obtained solutions for the problem, and PSO usually provided better results than GA. Regarding the final solution composition, steel contributes the most to emissions, welded profiles provided better solutions than laminated ones, and laminated spans of up to 17.5m and welded ones up to 27.5m dispensed with tendons.

An experimental study was carried out to evaluate the ductility of reinforced concrete beams longitudinally reinforced with hybrid FRP-Steel bars. The specimens were fourteen reinforced concrete beams with and without hybrid reinforcement. The test variables were bars position, the ratio of longitudinal reinforcement, and the type of FRP bars. The beams were loaded up to failure using a four-point bending test. The performance of the tested beams was observed using the load-deflection curve obtained from the test. Numerical analysis using the fiber element model was used to examine the growth of neutral axis depth due to the effect of test variables. The neutral axis curves were then used to further estimate the neutral axis angle and neutral axis displacement index. The test results show that the position of the reinforcement greatly influences the flexural behavior of the beam with hybrid reinforcement. It was observed from the test that the flexural capacity of beams with hybrid reinforcement is 4% to 50% higher than that of the beams with conventional steel bars depending on bars position and the ratio of longitudinal reinforcement. The ductility decreases as the hybrid reinforcement ratio (Af/As) increases. This study also showed that a numerical model developed can predict the flexural behavior of beams with hybrid reinforcement with reasonable accuracy.

In this paper a new approximate procedure is developed for calculating the inclination angle of the end points of statically determinate beams. The method is based on the topology comparison of simple (hinge-roller combination) supported beam and a resemblant cantilever beam. Assuming that the support reactions of the beam are active forces, the virtual displacements at the points of the reaction forces are calculated. Based on these values the inclination angle is calculated. Several examples are considered and the suggested in this paper, while the procedure is applied for various types of structures and loadings. The results, obtained by the suggested numerical procedure, are compared with analytical ones, and they are in good agreement.

The brittle shear failure of reinforced concrete beams is complexed and unfavorable. For decades, research on the mechanical properties and durability of recycled coarse aggregate (RCA) to make recycled aggregate concrete (RAC) has been widely investigated. However, test results on the shear strength of reinforced recycled aggregate concrete beams are still limited and contradictory. This paper reports the shear strength of reinforced recycled aggregate concrete beams without stirrups. Eight RAC beams and two controlled beams with natural coarse aggregate (NCA) were tested under the four-point flexural test with the shear span-to-effective depth ratio (a/d) of 3.10. Parameters in this study were the replacement percentage of RCA (0%, 25%, 50%, 75%, and 100%) and longitudinal reinforcement ratio (w) of 1.16% and 1.80%. It was found that the normalized shear stresses of RAC beams with w = 1.80% at all levels of replacement percentage were quite similar to that of the NAC counterparts. Normalized shear stress of the beam with 100% RCA and w = 1.16% was lower than that of the NAC beam by 5%. Database of 128 RAC beams without shear reinforcement from literature was analyzed to evaluate the ability of the most recent ACI 318-19 shear provisions in shear strength prediction. A reduction factor of 0.75 is proposed to the current ACI code provision to account for the physical variations of RCA such as replacement percentage, RCA source and quality, density, amount of residual mortar, and physical irregularity.

Fracture analysis of reinforced concrete deep beam strengthened with carbon fiber-reinforced polymer (CFRP) plates was carried out. The present research aims to find out whether the crack propagation in a strengthened deep beam follows linear elastic fracture mechanics (LEFM) theory or nonlinear fracture mechanics theory. To do so, a new energy release rate based on nonlinear fracture mechanics theory was formulated on the finite element method and the discrete cohesive zone model (DCZM) was developed in deep beams. To validate and compare with numerical models, three deep beams with rectangular cross-sections were tested. The code results based on nonlinear fracture mechanics models were compared with experimental results and ABAQUS results carried out based on LEFM. The predicted values of initial stiffness, yielding point and failure load, energy absorption, and compressive strain in the concrete obtained by the proposed model were very close to the experimental results. However, the ABAQUS software results have greater differences with the experimental results. For example, the predicted failure load for the shear-strengthened deep beam using the proposed model has only 6.3% differences compared to the experimental result. However, the predicted failure load using ABAQUS software based on LEFM has greater differences (25.1%) compared to the experimental result.

Adding steel fibers to concrete improves the capacity in tension-driven failure modes. An example is the shear capacity in steel fiber reinforced concrete (SFRC) beams with longitudinal reinforcement and without shear reinforcement. Since no mechanical models exist that can fully describe the behavior of SFRC beams without shear reinforcement failing in shear, a number of empirical equations have been suggested in the past. This paper compiles the existing empirical equations and code provisions for the prediction of the shear capacity of SFRC beams failing in shear as well as a database of 487 experiments reported in the literature. The experimental shear capacities from the database are then compared to the prediction equations. This comparison shows a large scatter on the ratio of experimental to predicted values. The practice of defining the tensile strength of SFRC based on different experiments internationally makes the comparison difficult. For design purposes, the code prediction methods based on the Eurocode shear expression provide reasonable results (with coefficients of variation on the ratio of tested to predicted results of 27% - 29%). None of the currently available methods properly describe the behavior of SFRC beams failing in shear. As such, this work shows the need for studies that address the different shear-carrying mechanisms in SFRC and its crack kinematics.

We investigate a possible reduction mechanism from (bosonic) Quantum Field Theory (QFT) to Quantum Mechanics (QM), in a way that could explain the apparent loss of degrees of freedom of the original theory in terms of quantum information in the reduced one. This reduction mechanism consists mainly in performing an ansatz on the boson field operator, which takes into account quantum foam and non-commutative geometry. Through the reduction mechanism, QFT reveals its hidden internal structure, which is a quantum network of maximally entangled multipartite states. In the end, a new approach to the quantum simulation of QFT is proposed through the use of QFT's internal quantum network

Every finite simple group P can be generated by two of its elements. Pairs of generators forP are available in the Atlas of finite group representations as (not necessarily minimal) permutation representations P . It is unusual but significant to recognize that a P is a Grothendieck’s dessin d’enfant D and that a wealth of standard graphs and finite geometries G - such as near polygons and their generalizations - are stabilized by a D. In our paper, tripods P − D − G of rank larger than two,corresponding to simple groups, are organized into classes, e.g. symplectic, unitary, sporadic, etc (as in the Atlas). An exhaustive search and characterization of non-trivial point-line configurationsdefined from small index representations of simple groups is performed, with the goal to recognize their quantum physical significance. All the defined geometries G's have a contextuality parameterclose to its maximal value 1.

This paper gives both a general canonical quantum gravity theory and the general canonical quantum gravity theories of the Universe and general black hole, and discovers the relations reflecting symmetric properties of the standard nonlinear gravitational Lagrangian, which are not relevant to any concrete metric models. This paper concretely shows the general commutation relations of the general gravitational field operators and their zeroth, first, second and third style, respectively, of high order canonical momentum operators for the general nonlinear system of the standard gravitational Lagrangian, and then has finished all the four styles of the canonical quantization of the standard gravity.

The inability to delineate a unified physical ontology that accounts simultaneously for the laws of special relativity and the results of quantum experiments has been a defining problem in physics for more than 100 years. This analysis addresses the problem by positing an ontic, mixed ontology composed of a “discrete” 4D spacetime and a physical, ultra-high dimensional (3 x N) “Planck Space.” Together, Planck Space and the three spatial dimensions of 4D spacetime form a tightly integrated ((3 x N) + 3) hyperspace (the “Dual Ontology”). Critically, the Dual Ontology’s structure replaces 1) the continuous, differentiable manifold of 4D spacetime with a discrete 4D spacetime and 2) mathematical 3N configuration spaces with a physical (3 x N) Planck Space. Moreover, the Dual Ontology is structurally and dynamically predicated on the one-to-one mapping and identity between the discrete spatial units that simultaneously form 4D spacetime and Planck Space. The one-to-one mapping and identity of the discrete spatial units support an integrated quantum dynamics based upon the dynamic evolution of single and N-body quantum states in 4D spacetime in full compliance with the laws of special relativity and the instantaneous collapse of all quantum states in an ontic Planck Space, where special and general relativity and more generally, 4D spacetime’s laws of physics, do not apply.

Huperzine A is an herbal reversible inhibitor of Acetylcholinesterase (AChE). A molecular docking analysis on Huperzine A molecule has been carried out to understand its structure, conformational flexibility, intermolecular interaction and the binding affinity in the active site of AChE enzyme. Further, the charge density distribution of huperzine A molecule (lifted from the active site of AChE) was determined from the high level quantum chemical calculations coupled with charge density analysis. The binding affinity of Huperzine A towards AChE was calculated from the molecular docking; the lowest docked energy is -8.46 kcal/mol. In the active site, huperzine A molecule interacts with acyl binding pocket-Phe330 of AChE, that is, the bicyclo ring group of huperzine A forms an intermolecular interaction with the oxygen atom of main chain of the amino acid residue Phe330 at the distances 3.02 and 3.25 Å respectively. On the other hand, a gas phase study on huperzine A molecule also performed using HF and DFT (B3LYP) methods with the basis set 6-311G**. The molecular structure, conformation, and the charge density distribution of huperzine A molecule in the gas phase have determined using quantum chemical calculations and the charge density analysis. The comparative studies between the gas phase and the active site forms of huperzine A molecule, explicitly reveals the degree of conformational modification and the charge density redistribution of huperzine A when present in the active site. The dipole moment of the molecule in the active site is 6.85 D, which is slightly higher than its gas phase value (5.91 D). The electrostatic potential (ESP) surface of active site molecule clearly shows the strong electronegative and positive ESP regions of the molecule, which are the expected strong reactive locations of the molecule.

Distributed fiber optic strain measurement techniques have become increasingly important in recent years, especially in the field of structural health monitoring of reinforced concrete structures. Numerous publications show the various monitoring possibilities from bridges to special heavy structures. The present study is intended to demonstrate the possibilities, but also the challenges, of distributed fiber optic strain measurement in reinforced concrete structures. For this purpose, concrete beams for 3-point bending tests were equipped with optical fibers on the reinforcement and concrete surface as well as in the concrete matrix in order to record the strains in the compression and tension zone. In parallel, an analytical approach based on the maximum strains in the uncracked and cracked states was performed using the Eurocode~2 interpolation coefficient. In principle, the structural design correlates with the measured values, but the strains are underestimated, especially in the cracked zone. During load increase, structural distortions in the compression zone affected the strain signal, making reliable evaluation in this zone difficult. The information content of distributed fiber optic strain measurement in reinforced concrete structures can offer tremendous opportunities. Future research should consider all aspects of the bond, sensor selection and positioning. In addition, there is a lack of information on the long-term stability of the joint and the fiber coating, as well as the effects of dynamic loading.

This paper presents an approach to the analysis of beams with rectangular cross-sections subjected to Saint-Venant torsion using the Fourier analysis, body forces being not considered. The Saint-Venant torsion of beams, also called free torsion or unrestrained torsion, is characterized by the absence of axial stresses due to torsion; only shear stresses are developed. The solution to this torsion problem consists of finding the Prandtl stress function that satisfies the governing equation and the boundary conditions, the governing equation being such that the Laplacian of the stress function has a constant value within the cross-section. In this paper, Fourier sine series was utilized to describe the constant value of the above mentioned Laplacian, while double sine series or simple sine series was utilized to describe the Prandtl stress function. Closed-form solutions in form of infinite series were derived for shear stresses, torsional constant and warping function. Those solutions were identical to the exact solutions.

Based on the prosed criterion of the type of heating, a classification of the sources of pulsed electron beams was carried out, for better understanding both the nature of the thermal processes occurring under irradiation and for predicting their suitability for certain applications. The melting thresholds of materials were calculated over the wide ranges of accelerating voltages and pulse durations. On the basis of calculations, a refractoriness series of metals for surface-volume pulsed heating was proposed.

This paper presents an approach to the two-dimensional analysis of elastic isotropic deep beams using the finite difference method (FDM). Deep beams are subjected to in-plane loading and present a shear span to height ratio of less than 2.50; consequently, Euler-Bernoulli beam theory and Timoshenko beam theory do not apply. Deep beams analysis is generally conducted using numerical methods such as the finite element method and to a lesser extent the FDM; the strut-and-tie model and the stress field method are also widely utilized. Analytical approaches usually make use of the Airy stress function, where stresses are formulated in terms of the stress function; however, the exact solution of this function satisfying all of the boundary conditions can hardly be found, even for simple cases. In this paper, deep beams were analyzed using the FDM. The FDM is an approximate method for solving problems described with differential equations. The FDM does not involve solving differential equations; equations are formulated with values at selected nodes of the structure. Therefore, the deep beam was discretized with a two-dimensional grid, and additional nodes were introduced at the boundaries and at positions of discontinuity (openings, brutal change of material properties, non-uniform grid spacing), the number of additional nodes corresponding to the number of boundary conditions at the node of interest. The introduction of additional nodes allowed us to apply the governing equations at boundary nodes and satisfy the boundary and continuity conditions. An Airy stress function approach and a displacement potential function approach were considered in this study whereby strong formulations of equations (equilibrium, kinematic, and constitutive) were set. Stress and stability analyses were carried out with this model; furthermore, deep beams of varying stiffness, layered beams, and beams having openings were analyzed. For slender beams, the results obtained with the Airy stress function approach showed good agreement with those of the Euler-Bernoulli beam theory, and for deep beams, the shapes of stress distributions were in good agreement with a proper understanding of the behavior of structures. On the other hand, the displacement potential function approach delivered unsatisfactory results, probably due to the use of an inefficient equation solver; a more powerful tool will be needed in future research for this purpose.

Optical tweezers, as a kind of ultra-sensitive acceleration sensing platform, show a minimum measurable value inversely proportional to the square of the diameter of the levitated spherical particle. However, the coupling of the displacement measurement between axes becomes notable, along with the increasing of the diameter. This paper analyzes the source of coupling in a forward scattering far-field detection regime and proposes a novel method of suppression. We theoretically and experimentally demonstrated that when three variable irises added into detection optics, without changing other parts of optical structures, the decoupling of triaxial displacement signals mixed with each other show significant improvement. The detection coupling ratio reduction of 49.1 dB and 22.9dB has been realized in radial and axial direction respectively, which is principally in accord with simulations. This low cost and robust approach makes it possible to accurately measure three-dimensional mechanical quantities simultaneously and even go further such as active cooling the particle to quantum ground state.

For shear-critical structural elements where the use of stirrups is not desirable, such as slabs or beams with reinforcement congestion, steel fibers can be used as shear reinforcement. The contribution of the steel fibers to the shear capacity lies in the action of the steel fibers bridging the shear crack, which increases the shear capacity and prevents a brittle failure mode. This study evaluates the effect of the amount of fibers in a concrete mix on the shear capacity of steel fiber reinforced concrete beams with mild steel tension reinforcement and without stirrups. For this purpose, twelve beams were tested. Five different fiber volume fractions were studied: 0.0%, 0.3%, 0.6%, 0.9%, and 1.2%. For each different steel fiber concrete mix, the concrete compressive strength was determined on cylinders and the tensile strength was determined in a flexural test on beam specimens. Additionally, the influence of fibers on the shear capacity is analyzed based on results reported in the literature, as well as based on the expressions derived for estimating the shear capacity of steel fiber reinforced concrete beams. The outcome of these experiments is that a fiber percentage of 1.2% or fiber factor of 0.96 can be used to replace minimum stirrups according to ACI 318-14 and a 0.6% fiber volume fraction or fiber factor of 0.48 to replace minimum stirrups according to Eurocode 2. A fiber percentage of 1.2% or fiber factor of 0.96 was observed to change the failure mode from shear failure to flexural failure. The results of this presented study support the inclusion of provisions for steel fiber reinforced concrete in building codes and provides recommendations for inclusion in ACI 318-14 and Eurocode 2, so that a wider adoption of steel fiber reinforced concrete can be achieved in the construction industry.

Abstract: We have filled a 24 mm diameter glass sphere with a transparent polymer-gel that is radio-fluorogenic, i.e. it becomes (permanently) fluorescent when irradiated, with an intensity proportional to the local dose deposited. The gel consists of >99.9% tertiary-butyl acrylate (TBA) pre-polymerized to ~15% conversion, and ~100 ppm maleimido-pyrene (MPy). Its dimensions and physical properties are close to those of the vitreous body of the human eye. We have irradiated the gel with a 3 mm diameter, 200 kVp X-ray beam with a dose rate of ~1 Gy/min. A 3D (video) view of the beam within the gel has been constructed from tomographic images obtained by scanning the sample through a thin sheet of UV light. To minimize optical artifacts, the cell was immersed in a square tank containing a refractive-index-matching medium. The 20%-80% penumbra of the beam was determined to be ~0.4 mm. The research was a preparatory investigation of the possibility of using the method to monitor the millimetre diameter proton pencil beams used in ocular radiotherapy.

In this paper, the connections between quantum non-locality and permutation symmetries are explored. This includes two types of symmetries: permutation across a superposition and permutation of qubits in a quantum system. An algorithm is proposed for nding the separability class of a quantum state using a method based on factorizing an arbitrary multipartite state into possible partitions, cyclically permuting qubits of the vectors in a superposition to check which separability class it falls into and thereafter using a reduced density-matrix analysis of the system is proposed. For the case of mixed quantum states, conditions for separability are found in terms of the partial transposition of the density matrices of the quantum system. One of these conditions turns out to be the Partial Positive Transpose (PPT) condition. A graphical method for analyzing separability is also proposed. The concept of permutation of qubits is shown to be useful in de ning a new entanglement measure in the `engle'.

We present a model of space that considers it to be a quantized dynamical entity which is a component of the universe along with matter and radiation. The theory is used together with thermodynamic data to provide a new view of cosmic evolution and an insight into the nature of dark energy and dark matter. Space is made up of energy quanta. The universe started from an atomic size volume at very high temperature and pressure near the Planck epoch. Upon expansion and cooling, phase transitions occurred resulting in the formation of radiation, fundamental particles, and matter. These nucleate and grow into stars, galaxies, and clusters. From a phase diagram of cosmic composition, we obtained a correlation between dark energy and the energy of space. Using the Friedmann equations, data from WMAP studies of the composition of the universe at 3.0 x 10⁵ (a=5.25 x 10^-2) years and at present (a=1), are well fitted by our model with an equation of state parameter, w= -0.7. The accelerated expansion of the universe, starting at about 7 billion years, determined by BOSS measurements, also correlates well with the dominance of dark energy at 7.25 x 10⁹ years ( a= 0.65). The expansion can be attributed to Quintessence with a space force arising from a quantum space field. From our phase diagram, we also find a correlation suggesting that dark matter is a plasma form of matter similar to that which existed during the photon epoch immediately prior to recombination. Our Quantum Space Model leads to a universe which is homogeneous and isotropic without the need for inflation. The thermodynamics of expansion is consistent with BOSS data that show the process to be adiabatic and the rate of expansion decelerating during the first 6 billion years after the Big Bang. However, it became non-adiabatic and accelerating thereafter. This implies an influx of energy from a source outside the universe; it warrants consideration as a possible factor in the accelerated expansion of the universe.

The paper considers the symmetries of a bit of information corresponding to one, two or three qubits of quantum information and identifiable as the three basic symmetries of the Standard model, U(1), SU(2), and SU(3) accordingly. They refer to “empty qubits” (or the free variable of quantum information), i.e. those in which no point is chosen (recorded). The choice of a certain point violates those symmetries. It can be represented furthermore as the choice of a privileged reference frame (e.g. that of the Big Bang), which can be described exhaustively by means of 16 numbers (4 for position, 4 for velocity, and 8 for acceleration) independently of time, but in space-time continuum, and still one, 17th number is necessary for the mass of rest of the observer in it. The same 17 numbers describing exhaustively a privileged reference frame thus granted to be “zero”, respectively a certain violation of all the three symmetries of the Standard model or the “record” in a qubit in general, can be represented as 17 elementary wave functions (or classes of wave functions) after the bijection of natural and transfinite natural (ordinal) numbers in Hilbert arithmetic and further identified as those corresponding to the 17 elementary of particles of the Standard model. Two generalizations of the relevant concepts of general relativity are introduced: (1) “discrete reference frame” to the class of all arbitrarily accelerated reference frame constituting a smooth manifold; (2) a still more general principle of relativity to the general principle of relativity, and meaning the conservation of quantum information as to all discrete reference frames as to the smooth manifold of all reference frames of general relativity. Then, the bijective transition from an accelerated reference frame to the 17 elementary wave functions of the Standard model can be interpreted by the still more general principle of relativity as the equivalent redescription of a privileged reference frame: smooth into a discrete one. The conservation of quantum information related to the generalization of the concept of reference frame can be interpreted as restoring the concept of the ether, an absolutely immovable medium and reference frame in Newtonian mechanics, to which the relative motion can be interpreted as an absolute one, or logically: the relations, as properties. The new ether is to consist of qubits (or quantum information). One can track the conceptual pathway of the “ether” from Newtonian mechanics via special relativity, via general relativity, via quantum mechanics to the theory of quantum information (or “quantum mechanics and information”). The identification of entanglement and gravity can be considered also as a ‘byproduct” implied by the transition from the smooth “ether of special and general relativity’ to the “flat” ether of quantum mechanics and information. The qubit ether is out of the “temporal screen” in general and is depicted on it as both matter and energy, both dark and visible.

A new framework in quantum chemistry has been proposed recently ("An approach to first principles electronic structure calculation by symbolic-numeric computation'' by A. Kikuchi). It is based on the modern technique of computational algebraic geometry, viz. the symbolic computation of polynomial systems. Although this framework belongs to molecular orbital theory, it fully adopts the symbolic method. The analytic integrals in the secular equations are approximated by the polynomials. The indeterminate variables of polynomials represent the wave-functions and other parameters for the optimization, such as atomic positions and contraction coefficients of atomic orbitals. Then the symbolic computation digests and decomposes the polynomials into a tame form of the set of equations, to which numerical computations are easily applied. The key technique is Grröbner basis theory, by which one can investigate the electronic structure by unraveling the entangled relations of the involved variables. In this article, at first, we demonstrate the featured result of this new theory. Next, we expound the mathematical basics concerning computational algebraic geometry, which are necessitated in our study. We will see how highly abstract ideas of polynomial algebra would be applied to the solution of the definite problems in quantum mechanics. We solve simple problems in "quantum chemistry in algebraic variety'' by means of algebraic approach. Finally, we review several topics related to polynomial computation, whereby we shall have an outlook for the future direction of the research.

Quantum chaos is presented as a paradigm of information processing by dynamical systems at the bottom of the range of phase-space scales. Starting with a brief review of classical chaos as entropy flow from micro- to macro-scales, I argue that quantum chaos came as an indispensable rectification, removing inconsistencies related to entropy in classical chaos: Bottom-up information currents require an inexhaustible entropy production and a diverging information density in phase space, reminiscent of Gibbs' paradox in Statistical Mechanics. It is shown how a mere discretization of the state space of classical models already entails phenomena similar to hallmarks of quantum chaos, and how the unitary time evolution in a closed system directly implies the “quantum death” of classical chaos. As complementary evidence, I discuss quantum chaos under continuous measurement. Here, the two-way exchange of information with a macroscopic apparatus opens an inexhaustible source of entropy and lifts the limitations implied by unitary quantum dynamics in closed systems. The infiltration of fresh entropy restores permanent chaotic dynamics in observed quantum systems. Could other instances of stochasticity in quantum mechanics be interpreted in a similar guise? Where observed quantum systems generate randomness, that is, produce entropy without discernible source, could it have infiltrated from the macroscopic meter? This speculation is worked out for the case of spin measurement.

In this work, we present some results related with the issue of the Loop Quantum Black Holes (LQBH) thermodynamics by the use of the tunneling radiation formalism. The information loss paradox is also discussed in this context, where we have considered the influence of back reaction effects.

We derive a quantum speed limit for unitary evolution for the case of mixed quantum states using the stronger uncertainty relation for mixed quantum states. This bound can be optimized over different choices of Hermitian operators for a better bound. We illustrate this with some examples and show its better performance with respect to three existing bounds for mixed quantum states.

There is a formal analogy between the evolution of the universe, when this is seen as a trajectory in the minisuperspace, and the worldline followed by a test particle in a curved spacetime. The analogy can be extended to the quantum realm, where the trajectories are transformed into wave packets that give us the probability of finding the universe or the particle in a given point of their respective spaces: the spacetime in the case of the particle and the minisuperspace in the case of the universe. The wave function of the spacetime and the matter fields, all together, can then be seen as a super-field that propagates in the minisuperspace and the so-called third quantisation procedure can be applied in a parallel way as the second quantisation procedure is performed with a matter field that propagates in the spacetime. The super-field can thus be interpreted as made up of universes propagating, i.e. evolving, in the minisuperspace. The analogy can also be used in the opposite direction. The way in which the semiclassical state of the universe is obtained in quantum cosmology allows us to obtain, from the quantum state of a field that propagates in the spacetime, the geodesics of the underlying spacetime as well as their quantum uncertainties or dispersions. This might settle a new starting point for a different quantisation of the spacetime.

The spin-torsion theory is a gauge theory approach to gravity that expands upon Einstein's general relativity (GR) by incorporating the spin of microparticles. In this study, we further develop the spin-torsion theory to examine spherically symmetric and static gravitational systems that involve free-falling macroscopic particles. We posit that the quantum spin of macroscopic matter becomes noteworthy on cosmic scales. We further assume that the Dirac spinor and Dirac equation adequately capture all essential physical characteristics of the particles and their associated processes. A crucial aspect of our approach involves substituting the constant mass in the Dirac equation with a scale function, allowing us to establish a connection between quantum effects and the scale of gravitational systems. This mechanism ensures that the quantum effect of macroscopic matter is scale-dependent and diminishes locally, a phenomenon not observed in microparticles. For any given matter density distribution, our theory predicts an additional quantum term, the quantum potential energy (QPE), within the mass expression. QPE induces time dilation, distance contraction, and thus mimics a gravitational well. When applied to cosmology, our theory yields a static cosmological model. The QPE serves as a counterpart to the cosmological constant introduced by Einstein to balance gravity in his static cosmological model. The QPE also offers a plausible explanation for the origin of the Hubble redshift (traditionally attributed to the universe's expansion). The predicted luminosity distance-redshift relation aligns remarkably well with SNe Ia data from the cosmological sample of SNe Ia. In the context of galaxies, QPE functions as the equivalent of dark matter. The predicted circular velocities align well with the rotation curve data from the SPARC (Spitzer Photometry and Accurate Rotation Curves database) sample. Importantly, our conclusions in this paper are reached through a conventional approach, with the sole assumption of the quantum effects of macroscopic matter on large scales, without the need for additional modifications or assumptions.

Currently, synthetic diamonds are finding new applications. Quantum devices can be created based on diamond plates with the desired concentration of defects in the structure of the crystal lattice. NV color centers can be used in quantum applications by irradiating plates with high-energy particles, followed by annealing at temperatures above 800°C to develop the spin-optical properties of the centers Diamond plates are subjected to electron irradiation and much less often to proton irradiation. As a result, synthetic diamond plates with NV centers ob-tained by proton irradiation are less studied, although proton irradiation makes it possible to obtain a layered structure of NV centers. In this work, single crystal diamond plates irradiated with protons were studied using polarization microscopy, IR spectroscopy and ODMR spectros-copy. It is shown that when creating NV centers, the distribution and concentration of C – defects in the sample, as well as mechanical stresses before and after irradiation (with subsequent an-nealing), can differ significantly from each other.

In ancient buildings, timber members could need specific on-site interventions, including reinforcement or repair, sometimes inserting of reinforcing material into grooves routed in the original sound wood. Grooves number, positions and dimensions, and strengthening materials may differ, according to the desired increase of bending stiffness and strength. The Modulus-of-Elasticity (MOE) of each beam is of key importance, but the incisions can affect it, net of the reduction of the removed wood. In this study 12 old beams were accurately measured and their static and dynamic MOEs calculated before and after the grooves processing, to simulate the operations of typical reinforcing interventions. One groove was routed along the length of each beam and deepened progressively by three steps. Tests have showed how the MOE is affected by the groove depth, decreasing up to one third. The paper proves how the weakening effect of grooves on-site can be assessed with dynamic MOE and roughly predicted by means of visual survey. Grooves need for strengthening beams, must be carefully evaluated because of the variation of the actual mechanical properties, net to lost wood.

The aim of this paper is to optimize thickness variation function of simply supported and cantilever beams, in terms of maximizing gaps between chosen neighboring frequencies and analyze obtained results. The optimization results are examined in terms of achieving the objective function (related to eigenproblem), but also in terms of their dynamics stiffness (forced vibrations excited by point harmonic load). In the optimization process, a Genetic Algorithm was used. Problems related to structural dynamics were solved by FEM implementation into the algorithm. Sample results were presented, and the developed algorithm was analyzed in terms of result convergence by examining several variable parameters. The authors demonstrated the validity of applying the described optimization tool to the presented problems. Conclusions were drawn regarding the correlation between stiffness and mass distribution in the optimized beams and the natural frequency modes in terms of which they were optimized.

We study the performance of a classical and quantum magnetic Otto cycle with a quantum dot as a working substance using the Fock-Darwin model with the inclusion of the Zeeman interaction. Modulating an external/perpendicular magnetic field, we found in the classical approach an oscillating behavior in the total work that is not perceptible under the quantum formulation. Also, we compare the work and efficiency of this system for different regions of the Entropy, $S(T,B)$, diagram where we found that the quantum version of this engine always shows a reduced performance in comparison to his classical counterpart.

(1) Background: Sensing of critical events or flow signatures in nature often presents itself as a coupled interaction between a fluid and arrays of slender flexible beams, such a wind-hairs or whiskers. It is hypothesized that important information is gained in highly noisy environments by the inter-correlation within the array. (2) Methods: The present study uses a model sea lion head with artificial whiskers in the form of slender beams (optical fibres), which are subjected to a mean flow with overlaid turbulent structures generated in the wake of a cylinder. Motion tracking of the array of fibres is used to analyse the correlation of the bending deformations of pairs of fibres. (3) Results: Cross-correlation of the bending signal from tandem pairs of whiskers proves that the detection of vortices and their passage along the animals head is possible even in noisy environments. The underlying pattern, during passage of a vortex core, is a jerk-like response of the whiskers, which can be found at later arrival-times in similar form in the downstream whisker's response. (4) Conclusion: Coherent vortical structures can be detected from cross-correlation of pairs of cantilever-beam like sensors even in highly turbulent flows. Such vortices carry important information within the environment, e.g. the underlying convection velocity. More importantly in nature, these vortices are characteristic elementary signals left by prey and predators. The present work can help to further develop flow, or critical event, sensory systems which can overcome high noise levels due to the proposed correlation principle.

Tremendous progress has been witnessed in artificial intelligence within the domain of neural network backed deep learning systems and its applications. As we approach the post Moore’s Law era, the limit of semiconductor fabrication technology along with a rapid increase in data generation rates have lead to an impending growing challenge of tackling newer and more modern machine learning problems. In parallel, quantum computing has exhibited rapid development in recent years. Due to the potential of a quantum speedup, quantum based learning applications have become an area of significant interest, in hopes that we can leverage quantum systems to solve classical problems. In this work, we propose a quantum deep learning architecture; we demonstrate our quantum neural network architecture on tasks ranging from binary and multi-class classification to generative modelling. Powered by a modified quantum differentiation function along with a hybrid quantum-classic design, our architecture encodes the data with a reduced number of qubits and generates a quantum circuit, loading it onto a quantum platform where the model learns the optimal states iteratively. We conduct intensive experiments on both the local computing environment and IBM-Q quantum platform. The evaluation results demonstrate that our architecture is able to outperform Tensorflow-Quantum by up to 12.51% and 11.71% for a comparable classic deep neural network on the task of classification trained with the same network settings. Furthermore, our GAN architecture runs the discriminator and the generator purely on quantum hardware and utilizes the swap test on qubits to calculate the values of loss functions. In comparing our quantum GAN, we note our architecture is able to achieve similar performance with 98.5% reduction on the parameter set when compared to classical GANs. With the same number of parameters, additionally, QuGAN outperforms other quantum based GANs in the literature for up to 125.0% in terms of similarity between generated distributions and original data sets.

(3+1)D quantum mechanics is a four-dimensional quantum formalism, which is developed neither in a Minkowski spacetime, nor in a purely Hilbert space and not its metric is Lorentzian. This quantum mechanics also yields the quantum Einstein field equation in (3+1)D quantum spacetime. Every observable (3+1)D quantum spacetime can be found to contain internally hidden opposite spin quantum state, that results Supersymmetry. Closed continuous mappings of this hidden quantum state immediately yield more extra hidden dimensions including string. This string is found to be fundamentally eleven-dimensional (rather than lower dimensional) by nature within this quantum spacetime, which is necessarily a natural phenomenon of (3+1)D Quantum Mechanics.

This research focuses on exploring generalized electron emissions in one-dimensional conducting materials, specifically examining field emission and thermionic emission. Additionally, the study investigates one-dimensional thermal radiation. The current density is derived for both one-dimensional thermionic emission and one-dimensional field emission. A generalized current density in one dimension is devised, taking into account arbitrary accelerating fields and temperature conditions. The formula for the one-dimensional current density is depicted with accelerating field and temperature across various work function materials. The current is also represented as a function of both temperature and electric field for various temperatures.