This study explores fault-tolerant consensus in leader-following heterogeneous multi-agent systems, focusing on actuator failures in uncrewed aerial vehicles (UAVs) and uncrewed ground vehicles (UGVs). An optimization-based fault-tolerant consensus algorithm is proposed. The algorithm utilizes the Euler-Lagrange formula to ensure system consistency under actuator failures, with the Lyapunov stability theory proving the asymptotic stability of the consistency error. The algorithm is applied to heterogeneous multi-agent systems of UAVs and UGVs to derive optimal fault-tolerant consensus control laws for each vehicle type. Simulation experiments give evidence for the feasibility of the proposed control strategy.

Deadlock is a real problem that can cause expensive, time-dependent hang-ups or failures in distributed computing systems. Some studies have been conducted with deadlock detection and resolution in generalized request computing models, most of these studies are based on the diffusing computation scheme, where forward and backward propagated probe and reply messages respectively are diffused between dependent processes. The replies carry the dependency information between processes for the initiator. Using this dependency information initiator can detect and resolve the deadlock cycle. It has been proven in the literature that a deadlock cycle length distribution is skewed with a large majority of cycles (90%) having length two. Based on this fact an improved algorithm is proposed for handling deadlock detection in distributed computing systems under the distributed request model where each process has several requests at a time. The improved algorithm depends mainly on message propagation and timeout policy. Probe and reply messages are propagated between the initiator and its successors only to detect deadlock cycles between them. Global timeout policy is used to detect potential deadlock cycles with large length distribution. The proposed algorithm can handle concurrent executions. Simulation experiments are performed to see the effectiveness of the improved algorithm. It is found that the improved algorithm compares favorably with other existing algorithms and it shows better results for several performance metrics especially in reducing deadlock latency and execution time.

In this paper we describe a method which combines sentiment analysis with machine learning techniques and/or multivariate statistical analysis. By applying this methodology it is possible to classify a collection of texts into two or more groups or clusters. On the basis of a number of previously defined clusters, the novelty of the outlined approach is the use of the sentiment analysis results as input to the machine learning model or multivariate statistical analysis. Once the classifier has been obtained, we can assign a given text into one of the pre-established clusters. The groups or clusters can represent different time periods, classes of texts transcribed from different conversations, etc. The method is illustrated through an example taken from one of the two studies in which we have applied this methodology. In one of the studies, the method was used to classify press news of a volcanic eruption, while in the other study it was used to classify the conversations recorded between a chatbot with different kinds of speakers (humans or chatbots). This last study was the seminal work in which we introduced this methodology.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

Segment Anything Model 2 (SAM 2) is a state-of-the-art development by Meta AI Research, designed to address the limitations of its predecessor, SAM, particularly in the realm of video segmentation. SAM 2 employs a transformer-based architecture enhanced with streaming memory, enabling real-time processing for both images and videos. This advancement is important given the exponential growth of multimedia content and the subsequent demand for efficient video analysis. Utilizing the SA-V dataset, SAM 2 excels in handling the intricate spatio-temporal dynamics inherent in video data, ensuring accurate and efficient segmentation. Key features of SAM 2 include its ability to provide real-time segmentation with minimal user interaction, maintaining robust performance even in dynamic and cluttered visual environments. This study provides a comprehensive overview of SAM 2, detailing its architecture, functionality, and diverse applications. It further explores the model's potential in improving practical implementations across various domains, emphasizing its significance in advancing real-time video analysis.

As technology advances, people are increasingly adopting IoT (Internet of Things) devices in smart cities. These devices are equipped with sensors that are connected everywhere, from energy infrastructure and transportation to telecommunications, health and human services, waste management, public safety, and more. People want to access sensor data anytime and everywhere to make better decisions and improve their lives. To achieve this, a sensor integration model has been developed where multiple sensors are integrated under one gateway to manage and share sensor data. However, effective sharing of sensor data requires data security, privacy, confidentiality, fairness, effective architectural design, and low communication and computation costs. These issues need to be addressed in the sensor integration model in smart cities. Existing storage models face challenges in managing sensor data effectively. To overcome these issues and hurdles, a data storage framework leveraging blockchain technology has been proposed within the sensor integration model. This framework ensures data security, privacy, confidentiality, and a fair and transparent financial model, all while minimizing communication and computation costs.

Objectives (Purpose) This study aims to evaluate the outcomes of the Subcrestally Placed Implant (SPI) technique in single molar cases, focusing on biological stability and aesthetics. It proposes a schematic model to elucidate the interplay between the biological stability of soft tissues and bone around the SPI and the morphological requisites that Implant Abutment Prostheses (IAP) must fulfill to effectively replace natural teeth. Materials and methods I examined 20 cases using the SPI technique with Internal Platform Switching (IPS) design implants for single molar replacements to assess their stability. Routine check-ups utilized plain panoramic X-rays to measure changes in crestal bone on the mesial and distal sides. Additionally, 10 cases with CBCT X-rays taken more than one year after the initial surgery underwent a novel 3-dimensional soft tissue analysis (3DSTA). Measurements included placement depths (PD), soft tissue thickness (STT) at central (cPD, cSTT) and peripheral areas (pPD, pSTT), the length of the Transitional Zone (TZ) on mesial, distal, facial, and lingual aspects, and crestal bone thickness (CBT) at buccal and lingual sites. Results Panoramic analyses showed minimal changes in crestal bone (mean changes of pPD were less than 0.1 mm) over an average period of 3.3 years. Average measurements were as follows: cPD was 1.7 mm, pPD was 2.7 mm, cSTT was 0.2 mm, pSTT was 0.6 mm, TZ length was 3.8 mm, buccal CBT was 3.0 mm, and lingual CBT was 3.7 mm. Conclusions CBCT analyses of the topographical relationships between soft tissue and crestal bone with IAP for SPIs demonstrated stable results over an average 3-year period. The consistency in the relationship between crestal bone and surrounding soft tissue can be ascribed to biological structural integrity. The study classified peri-implant soft tissues into subcrestal and supracrestal (transitional zone – TZ) segments, exploring their characteristics through dimensional measurements and assessing mechanical resistance. Further histological study is needed to identify specific features of each segment.

Introduction The placement of implants is often hindered by a severely atrophic mandibular edentulous ridge. A sufficient volume of bone graft is crucial for successful implant restoration. The required bone graft volume directly correlates with the deficiency present in the edentulous ridge. If the residual crestal bone height is so low that the distance between the crestal ridge and the inferior alveolar nerve is less than 2 mm, a significant bone augmentation procedure is necessary. This procedure must ensure the implants are surrounded by a sufficient margin of bone, aiming for a final height of more than 8 mm and a width of more than 7 mm. Achieving primary closure with adequate soft tissue is vital for the success of the bone graft procedure. The key to successful bone grafting lies in the effective management of the soft tissue covering. Case Report This case report details the treatment of a patient with severely atrophic edentulous ridges on both sides, addressed using Self Inflating Tissue Expanders (SITEs) to facilitate bone grafting and implant placement. Following soft tissue expansion, bone grafting and implant placement were successfully performed. The implants supported a fixed restoration, which remained stable and complication-free over a seven-year observation period. Conclusion The SITE (Self-Inflating Tissue Expander) proved effective in obtaining a substantial amount of bone graft needed for implant installation. A seven-year follow-up confirmed the implants were well-functioning with stable bone support, healthy soft tissue coverage, and adequate vestibular depth.

Plant cells' ability to withstand abiotic stress is strongly linked to modifications in their mechanical characteristics. Nevertheless, the lack of a workable method for consistently tracking plant cell mechanical properties severely restricts our comprehension of the mechanical alterations in plant cells under stress. With Polyethylene Glycol (PEG6000), we created a drought-like environment, and we used the Double Resonator Piezoelectric Cytometry (DRPC) method to dynamically and non-invasively track changes in the stress (ΔS) created and viscoelasticity (storage modulus G' and loss modulus G") of protoplasts and suspension cells of rice during drought stress. The findings demonstrate that, rice suspension cells and protoplasts react mechanically differently to 5%–15% PEG6000 stress, implying distinct resistance mechanisms. However, neither of them can withstand 25% PEG6000 stress, they respond mechanically similarly to 25% PEG6000 stress. The results of DRPC are further corroborated by the morphological alterations of rice cells and protoplasts observed under an optical microscope. To sum up, the DRPC technique functions as a precise cellular mechanical sensor and offers novel research tools for the evaluation of plant cell adversity and differentiating between the mechanical reactions of cells and protoplasts under abiotic stress.

Parkinson's disease (PD) is the second most common neurodegenerative disorder, entailing several motor-related symptoms that contribute to a reduced quality of life in affected subjects. Recent advances in wearable technologies and computing resources have shown great potential for the assessment of PD-related symptoms. However, the potential applications (e.g., early diagnosis, prognosis and monitoring) and key features of digital biomarkers for motor symptoms of PD (DB-MS-PD) have not been comprehensively studied. This study aims to provide a state-of-the-art review of current digital biomarker definitions for PD, focusing on the use of wearable devices. This review systematically examines research articles from 2012 to 2024, focusing on key features and recent technologies in PD research. A total of 22 studies were included and thoroughly analyzed. Results indicate that DB-MS-PD can accurately distinguish patients with PD (PwPD) from healthy controls (HC), assess disease severity or treatment response, and detect motor symptoms. Large sample sizes, proper validation, non-invasive devices, and ecological monitoring make DB-MS-PD promising for improving PD management. Challenges include sample and method heterogeneity and lack of public datasets. Future studies can leverage evidence of the current literature to provide more effective and ready-to-use digital tools for monitoring PD.

Toll plaza optimization is essential for improving traffic flow and easing congestion on road networks. This study aims to suggest and assess potential optimization solutions for the Peshawar toll plaza, considering variables like traffic volume, toll-collecting effectiveness, and customer facilitation. Different resources are used for data collection, like the National Highway Authority of Pakistan. Physical data is collected from the established Toll Plaza of Peshawar, along with the development of each line. The goal of this study is to suggest and assess potential optimization solutions for the Peshawar toll plaza, considering variables like traffic volume, toll-collecting effectiveness, and customer happiness. The analysis of present traffic patterns, the detection of bottlenecks, and the creation of plans to ease congestion and enhance overall traffic flow are all part of the optimization process. The approaches used in this study include data analysis, simulation, and traffic modeling. PTV VISSIM is software for transportation planning, design, and analysis. The simulations consider various conditions, such as variable traffic volumes, toll collection methods, and lane configurations. When comparing the different optimization strategies, performance indicators like trip time, latency, and queue length are utilized to determine which approach is practical. Waiting time Vs. Existing each lane, etc, is explained. In the end, comparing queue lengths and throughput across different lane scenarios shows that maximizing throughput with existing lanes yields up to 45% improvement with E-tag lanes, 40% with existing E-tag lanes, 38% with E-tag plus additional toll and cash lanes, 32% with three cash lanes, and 28% with two E-tag lanes. Failure to regularly monitor and adjust the existing lane pattern scenario based on traffic patterns can lead to queues being 20% longer. Without proactive evaluation and optimization, there is a potential 63% opportunity for queue length improvement

The presence of escaped fish in aquaculture facilities as a result of harsh meteorological conditions (more pressing in a face of climate change) requires a better understanding of these dynamical behaviour through vigilant monitoring and validated numerical models. In this context, data from strain, stress sensors as well as meteorological and current sensors installed at an aquaculture farm in the Region of Murcia (Spain) were collected, processed and analysed. Among them, first results about the relationship between load and currents sensors are presented. Due to the complexity of the time series, various analyses were conducted to examine their interrelation, encompassing regression analysis of raw data and data segmented into different time intervals. Through this analysis, it was observed that employing distinct time windows better elucidated the data variability. Furthermore, an optimal data window of 240 data was identified, demonstrating significantly improved explanatory power, with the coefficient of determination (R2) increasing by approximately 0.8 depending on the section. This pave the way for optimizing the monitoring features that must be carried out to relate cause-and-effect variables in the behaviour of these off-shore infrastructures.

Environmental factors, such as drought-stress, significantly impact maize growth and productivity worldwide. To improve yield and quality, effective strategies for early detection and mitigation of drought-stress in maize are essential. This paper presents a detailed analysis of three imaging trials conducted to detect drought-stress in maize plants using an existing, custom-developed, low cost, high throughput phenotyping platform. We propose a pipeline for early detection of water stress in maize plants using a Vision Transformer classifier and analysis of distributions of near-infrared (NIR) reflectance from the plants. We also explored suitable regions on the plant that are more sensitive to drought-stress and show that the region surrounding the youngest expanding leaf (YEL) and the stem can be used as a more consistent alternative to analysis involving just the YEL. Our results show good separation between well-watered and drought-stressed trials for two out of the three imaging trials both in terms of classification accuracy from data-driven features as well as through analysis of histograms of NIR reflectance.

The paper presents the design and the implementation of different advanced control strategies that are applied to a nonlinear model of a thermal unit. A data–driven grey–box identification approach provided the physically meaningful nonlinear continuous–time model, which represents the benchmark exploited in this work. The control problem of this thermal unit is important since it constitutes the key element of passive air conditioning systems. The advanced control schemes analysed in this paper are used to regulate the outflow air temperature of the thermal unit by exploiting the inflow air speed, whilst the inflow air temperature is considered as an external disturbance. The reliability and robustness issues of the suggested control methodologies are verified with a Monte–Carlo analysis for simulating modelling uncertainty, disturbance and measurement errors. The achieved results serve to demonstrate the effectiveness and the viable application the suggested control solutions to air conditioning systems. The benchmark model represents one of the key issues of this study, which is exploited for benchmarking different model–based and data–driven advanced control methodologies through extensive simulations. Moreover, this work highlights the main features of the proposed control schemes, while providing practitioners and heating, ventilating and air conditioning engineers with tools to design robust control strategies for air conditioning systems.

Glycans are involved in various metabolic processes via the functions of glycosyltransferases and glycoside hydrolases. Analysing the evolution of these enzymes is essential for improving the understanding of glycan metabolism and function. Based on our previous study of glycosyltransferases, we performed a genome-wide analysis of whole human glycoside hydrolases using the UniProt, BRENDA, CAZy, and KEGG databases. Using cluster analysis, 319 human glycoside hydrolases were classified into four clusters based on their similarity to enzymes conserved in chordates or metazoans (Class 1), metazoans (Class 2), metazoans and plants (Class 3), and eukaryotes (Class 4). The eukaryote and metazoan clusters included N- and O-glycoside hydrolases, respectively. The significant abundance of disordered regions within the most conserved cluster indicated a role for disordered regions in the evolution of glycoside hydrolases. These results suggest that the biological diversity of multicellular organisms is related to the acquisition of N- and O-linked glycans.

Laser-targeted weeding methods further enhance the sustainable development of green agriculture, with one key technology being the improvement of weed localization accuracy. Here, we propose an improved YOLOv8 instance segmentation based on bidirectional feature fusion and deformable convolution (BFFDC-YOLOv8-seg) to address the challenges of insufficient weed localization accuracy in complex environments with resource-limited laser weeding devices. Initially, by training on extensive datasets of plant images, the most appropriate model scale and training weights are determined, facilitating the development of a lightweight network. Subsequently, the introduction of the Bidirectional Feature Pyramid Network (BiFPN) during feature fusion effectively prevents the omission of weeds. Lastly, the use of Dynamic Snake Convolution (DSConv) to replace some convolutional kernels enhances flexibility, benefiting the segmentation of weeds with elongated stems and irregular edges. Experimental results indicate that the BFFDC-YOLOv8-seg model achieves a 4.9% increase in precision, an 8.1% increase in recall rate, and a 2.8% increase in mAP50 value to 98.8% on a vegetable weed dataset compared to the original model. It also shows improved mAP50 over other typical segmentation models such as Mask R-CNN, YOLOv5-seg, and YOLOv7-seg by 10.8%, 13.4%, and 1.8%, respectively. Furthermore, the model achieves a detection speed of 24.8 FPS on the Jetson Orin nano standalone device, with a model size of 6.8MB that balances between size and accuracy. The model meets the requirements for real-time precise weed segmentation, suitable for complex vegetable field environments and resource-limited laser weeding devices.

Data is the most valuable asset of a company or organisation nowadays, for the management of such data there are several techniques used for the storage and analysis of these data, if the organisation chooses wrongly among the alternatives it could face a very costly problem. Based on the above information we will study a very important issue today in the business world, with the global economic growth has also grown the world of technology and therefore organizations or companies also need to move forward with firm and fast pace how business evolves; Its weaknesses, strengths and the need to always be at the forefront of technological tools we will dive into the subject of business intelligence or also known as Business Intelligence (BI), Datawarehouse and Data Mining which is nothing more than a group of applications and tools that allow you to extract, transform and load some data to get to get information and knowledge in order to make a quick decision, accurate and efficient in the organization to achieve the objectives outlined. Due to the fact that there are still companies or organisations that make blind decisions in their customer or strategic processes. In order to solve this problem we rely on data mining as an alternative to minimise risks, which can lead to major and valuable losses within an organisation. In the case of a private company where data mining is applied to study patterns of customer behaviour on their own parameters of location, consumption, etc.. And third party data. The search for information is profitable for the business administration. Data mining is applied as a tool for the development of marketing tactics in competitive production and industrial sectors. This technology attempts to help perceive the attachment of databases. Data mining works on a preferential level looking for patterns, behaviours, orders or groupings that can create a model that allows us to better understand the concept and help in decision making so organisations rely on different systems such as CRM, ERP and many others, but to move from just information to generate business intelligence must be centralised in a single place where you can run data analysis of all types to discover trends that help decision making that place can be mainly a Lake or a Warehouse.

Selecting road networks in cartographic generalization has consistently posed formidable challenges, driving research towards the application of intelligent models. Despite previous efforts, the accuracy and connectivity preservation in these studies, particularly when dealing with road types of similar sample sizes, still warrant improvement. To address these shortcomings, we introduce a Heterogeneous Graph Attention Network (HAN) for road selection, where feature masking method is initially utilized to assess the significance of road features. Concentrating on the most relevant features, two meta-paths are introduced within the HAN framework: one for aggregating features of the same road type within the first-order neighborhood, emphasizing local connectivity, and another extending this aggregation to the second-order neighborhood, capturing a broader spatial context. For a comprehensive evaluation, we introduce a set of metrics considering both quantitative and qualitative aspects of the road network. Compared to traditional neural networks, our HAN model demonstrates superior accuracy and F1-score, particularly for road types with comparable samples. Additionally, it enhances the overall connectivity of the selected network. In summary, our HAN-based method provides an advanced solution for road network selection, surpassing previous approaches in terms of accuracy and connectivity preservation.

Due to the uniqueness of the underwater environment, traditional data aggregation schemes face many challenges. Most existing data aggregation solutions do not fully consider node trustworthiness, which may result in the inclusion of falsified data sent by malicious nodes during the aggregation process, thereby affecting the accuracy of the aggregated results. Additionally, because of the dynamically changing nature of the underwater environment, current solutions often lack sufficient flexibility to handle situations such as node movement and network topology changes, significantly impacting the stability and reliability of data transmission. To address the aforementioned issues, this paper proposes a secure data aggregation algorithm based on a trust mechanism. By dynamically adjusting the number and size of node slices based on node trust values and transmission distances, the proposed algorithm effectively reduces network communication overhead and improves the accuracy of data aggregation. Due to the variability in the number of node slices, even if attackers intercept some slices, it is difficult for them to reconstruct the complete data, thereby ensuring data security.

Urbanization and climate change have increased the need for stormwater management and nature-based solutions. Decisions made at project level impact the emergence of systemic traits of the stormwater network and the functionality of the catchment areas in urban planning. To that end, it is vital to introduce the decision-making tools for analyzing both the utilities and amenities of nature-based solutions (NBS) to increase their adoption to reduce the peak loads in the stormwater system, and to that end, mitigate the impacts of climate change. This paper demonstrates a workflow using drone-based photogrammetry, 3D modeling, and simulation software to generate visual and functional models assisting in informed decision-making in the design of stormwater systems as functional landscape architecture. Using aerial data from drones and modeled design solutions, the proposed workflow simulates rain events, infiltration, evaporation, water flow, and accumulation of stormwater in a way that allows the visual and quantified analysis of detailed landscape architecture designs. The paper provides an example of a rooftop site simulation demonstrating the infiltration and flow of water to the drainage. The visual decision-making method provided can aid in investment decisions for functional landscape design in support of stormwater management.

This article explores the specific impact of artificial intelligence (AI) -driven data visualisation technologies in the user experience of the Internet industry. Through the introduction of machine learning and data mining technologies, AI has significantly improved the intelligence and automation of data visualization tools, promoting innovation in visualization methods and improving the quality and efficiency of data cleaning, processing, and analysis. In addition, AI has also promoted the development of personalised data visualization, providing users with a richer and more intuitive way to present data. This paper analyses the applications of AI-driven data visualization in machine learning, natural language processing, and computer vision. It demonstrates the positive effects of AI data visualization on user understanding and optimisation of models through practical feedback from Yellowbrick tools.

The key links of face recognition are digital image preprocessing, facial feature extraction and pattern recognition, this article aimed at the current problem of slow speed and low recognition accuracy of face recognition , from the above three key links, on the basic of analyzing the therories of Fractional Differential Masks Operator (FDMO), Principal Component Analysis (PCA) and Support Vector Machine (SVM), design a kind of FDMO+PVA+SVM coupling algorithm that applies to face recognition to improve the speed and accuracy of it. To realize FDMO+PCA+SVM coupling algorithm, first, we should apply FDMO to face image processing binary marginalization, the purpose is getting face contour; Then, we apply PCA to get the feature of face image which is disposed by binary marainalization. At last, we can apply One-Against All of the SVM classifier and LibSVM software package to realize face recognition. Beside, the article with nine different coupling algorithm design four groups of experimental reaults on the ORL face database verified by comparative analysic FDMO+PCA+SVM coupling algorithm in the superiority of face recognition accuracy and speed.

The business planning process can be considered as a strategic phase of any business. Given that the business plan is a management accounting tool, there are countless approaches that can be adopted to prepare it since there is no legal requirement, as opposed to obligations relating to financial accounting. However, in general, every business plan consists of a numerical part (budget) and a narrative part. In this research, the author highlights, on the basis of experiences and commonly used theories, a standard process that can be adaptable to the business plan of any type of activity. The use of big data is highlighted as an essential part of feeding the data of almost all the steps of the budget. The author then manages to determine a generally applicable standard process, indicating all the data necessary to prepare an accurate and reliable business plan. A case study will provide adequate support to the demonstration of the immediate applicability of the proposed model.

The integration of Artificial Intelligence (AI) with the Internet of Things (IoT) has propelled technological innovation across various industries. This systematic literature review explores the current state and future trajectories of AI in IoT, with a particular focus on emerging trends in intelligent data analysis and privacy protection. The proliferation of IoT devices, marked by voluminous data generation, has reshaped data processing methods, providing actionable insights for informed decision-making. While previous reviews have offered valuable insights, they often fall short of comprehensively addressing the multifaceted dimensions within the AI-driven IoT landscape. This review aims to bridge this gap by systematically examining existing literature and acknowledging the limitations of past studies. To achieve this aim, the study uses a meticulous approach guided by established methodologies. The chosen methodology ensures the rigor and validity of the review, aligning with PRISMA guidelines for systematic reviews. This systematic literature review serves as a comprehensive guide for researchers, practitioners, and policymakers, offering insights into the current landscape and paving the way for future research directions. The identified trends and challenges provide a valuable resource for navigating the evolving domain of AI in IoT, fostering a balanced, secure, and sustainable advancement in this dynamic field.

This research describes numerical methods to analyze the absolute transport demand of cyclists and then to quantify the road network weaknesses of a city with the aim to identify infrastructure improvements in favor of cyclists. The methods are based on a combination of bicycle counts and map-matched GPS traces and are demonstrated with the city of Bologna, Italy: the dataset is based on approximately 27,500 GPS traces from cyclists, recorded over a period of one month on a volunteer basis using a smartphone application. A first method estimates absolute, city-wide bicycle flows, by scaling map-matched bicycle flows of the entire network to manual and instrumental bicycle counts of the main bikeways of the city. As there is a good correlation between the two sources of flow data, the absolute bike-flows on the entire network have been correctly estimated. A second method describes a novel link-deviation index, which quantifies for each network edge the total deviation generated for cyclists in terms of extra distances traveled with respect to the shortest possible route. The deviations are accepted by cyclists either to avoid unpleasant road attributes along the shortest route or to experience more favorable road attributes along the chosen route. The link deviation index indicates the planner which road links are contributing most to the total deviation of all cyclists – in this way, repelling and attracting road attributes for cyclists can be identified. This is why the deviation index is of practical help to prioritize bike infrastructure construction on individual road network links.

Synthetic Aperture RADAR (SAR) is a radar imaging technique in which the relative motion of the sensor is used to synthesize a very long antenna and obtain high spatial resolution. Standard SAR raw data processing techniques assume uniform motion of the satellite (or aerial vehicle) and a fixed antenna beam pointing sideway orthogonally to the motion path, assumed rectilinear. Despite SAR data processing is a well established imaging technology that has become fundamental in several fields and applications, in this paper a novel approach has been used to exploit coherent illumination, demonstrating the possibility of extracting a large part of the ancillary data information from the raw data itself, to be used in the focusing procedure. In this work an effort has been carried out to try to focus the raw SAR complex data matrix without the knowledge of anyof the parameters needed in standard focusing procedures as Range Doppler (RD) algorithm, ω - K algorithm and Chirp Scaling (CS) algorithm. All the literature references regarding the algorithms needed to obtain a precise image from raw data use such parameters that refer both to the SAR system acquisition geometry and its radiometric specific parameters. In [12], authors introduced a preliminary work dealing with this problem and able to obtain, in the presence of a strong point scatterer in the observed scene, good quality images, if compared to the standard processing techniques. In this work the proposed technique is described and performances parameters are extracted to compare the proposed approach to RD.

Autism Spectrum Disorder (ASD) is a neuro-developmental disorder that limits social interactions, cognitive skills, and abilities. Since ASD can last during an affected person's entire life cycle, the diagnosis at the early onset can yield a significant positive impact. The current medical diagnostic systems (e.g., DSM-5/ICD-10) are somewhat subjective; rely purely on the behavioral observation of symptoms, and hence, some individuals often go misdiagnosed or late-diagnosed. Therefore, researchers have focused on developing data-driven automated diagnosis systems with less screening time, low cost, and improved accuracy while significantly reducing professional intervention. Human Activity Analysis (HAA) is considered one of the most promising niches in computer vision research. This paper aims to analyze its potentialities in the automated detection of autism by tracking the exclusive characteristics of autistic individuals such as repetitive behavior, atypical walking style, and unusual visual saliency. This review provides a detailed inspection of HAA-based autism detection literature published in 2011 on-wards depicting core approaches, challenges, probable solutions, available resources, and scopes of future exploration in this arena. According to our study, deep learning outperforms machine learning in ASD detection with a classification accuracy of 76\% to 95\% on different datasets comprise of video, image, or skeleton data that recorded participants performing a large number of actions. However, machine learning provides satisfactory results on datasets with a small number of action classes and has a range of 60\% to 93\% accuracy among numerous studies. We hope this extensive review will provide a comprehensive guideline for researchers in this field.

Even if the field of medicine has made great strides in recent years, infectious diseases caused by novel viruses that damage the respiratory system continue to plague people all over the world. This type of virus is very dangerous, especially for people who deal with serious long-term breathing problems, like triggering asthma, pneumonia, or bronchitis infections. Thus, this paper demonstrates a new Secure Machine Learning Monitoring System for a model for virus detection. Our proposed model makes use of 4 basic emerging technologies, Internet of Things (IoT), Wireless Sensor Networks (WSN), Cloud Computing (CC), and Machine Learning (ML), to detect dangerous types of viruses that infect people or animals causing panic worldwide and deregulating human daily life. The proposed system is a robust system that could be established in various buildings, like hospitals, entertainment halls, universities, etc., and will provide accuracy, speed, and privacy for data collected in the detection of viruses.

Users with Autism Spectrum Disorder may find human-computer interaction (HCI) challenging due to a number of symptoms experienced, one of which is difficulty coping with change. Through capturing, comparing and statistically analysing the reactions of autistic and neurotypical users to seven individual design changes, it has been possible to identify the changes that cause significant difficulty in autistic users. These difficulty points were then used to form heuristics that can followed by HCI practitioners in the industry to reduce the negative impact of software interface design change on autistic users, hence making software updates more accessible.

The origin of a product, consumer familiarity, and purchasing identity are factors that affect perception of cheese consumption. The present study aims at identifying consumers’ conceptualizations and attitudes towards local Greek cheeses of the North-Aegean Sea islands, such as Ladotyri, Graviera, Kasseri, Kaskavali, Melichloro, and Kalathaki, some of which have a Protected Designation of Origin (PDO) status, as opposed to cheeses of non-Greek origin, such as Cheddar, Regatto, and Gouda. Sensory and emotional attributes of local, local PDO, and imported cheeses, and drivers associated with consumers’ choice and acceptance above and beyond their sensory attributes were studied, using three methods: a) Flash Profile to gain insight into the sensory positioning of products and description of samples, b) qualitative analysis of focus groups to pinpoint consumer knowledge, preference, and consumption criteria, and c) a new methodology for natural language processing and sentiment analysis of social media posts to determine consumer conceptualizations. Social media posts have proven to be a valuable source of linguistic and cultural data for cheeses. Local cheeses, including PDO products, were found to be linked to village life and family gatherings, home, tradition, and childhood memories, with saltiness and hardness being their main sensory attributes. Imported cheeses were linked to fast food, pizza, and snacking, with elasticity and gumminess as prominent sensory qualities. The main criterion of purchase was intended usage and versatility, taste and texture, price, and familiarity. The findings provide key sensory attributes, information about consumer purchasing criteria, and relevant vocabulary for the promotion of cheeses as agri-food and gastronomic identity key products.

Private Set Intersection (PSI) is a cryptographic method in secure multi-party computation that allows entities to identify common elements in their datasets without revealing their private data. Traditional approaches assume similar-sized datasets and equal computational power, overlooking practical imbalances. In real-world applications, dataset sizes and computational capacities often vary, particularly in the Internet of Things and mobile scenarios where device limitations restrict computational types. Traditional PSI protocols are inefficient here, as computational and communication complexities correlate with the size of larger datasets. Thus, adapting PSI protocols to these imbalances is crucial. This paper explores unbalanced PSI scenarios where one party (the receiver) has a relatively small dataset and limited computational power, while the other party (the sender) has a large amount of data and strong computational capabilities. It introduces three innovative solutions for unbalanced PSI: unbalanced PSI protocol based on Cuckoo filters, unbalanced PSI protocol based on single cloud assistance, and unbalanced PSI protocol based on dual cloud assistance, each addressing the shortcomings of the previous solution. These protocols primarily optimize database computational load, storage capacity, protocol execution time, and security. Depending on performance and security needs, different protocols can be employed for applications such as private contact discovery.

The generation of forensic DNA profiles consisting of single nucleotide polymorphisms (SNPs) is now being facilitated by wider adoption of next-generation sequencing (NGS) methods in casework laboratories. At the same time, and in part because of this advance, there is an intense focus on the generation of SNP profiles from evidentiary specimens for so-called forensic or investigative genetic genealogy (FGG or IGG) applications. However, FGG methods are constrained by the algorithms for genealogical database searches, which were designed for use with single-source profiles, and the fact that many forensic samples are mixtures. To enable the use of two-person mixtures for FGG, we developed a workflow, MixDeR, for the deconvolution of mixed SNP profiles. MixDeR, a flexible and easy to use R package and Shiny app, processes ForenSeq Kintelligence® (QIAGEN, Inc.) SNP genotyping results and directs deconvolution of the profiles in EuroForMix (EFM). MixDeR then filters the EFM outputs to produce inferred single-source genotypes in reports formatted for use with GEDmatch® PRO. An optional MixDeR output includes metrics that assist with testing and validation of the workflow. As the Shiny app provides a graphical user interface and the software is designed to be run offline, MixDeR should be suitable for use by any laboratory developing FGG capabilities, no matter their bioinformatic resources or expertise.

Responding to changing value creation processes in the sheet metal working sec-tor, where the complexity and interchangeability of products challenge traditional dif-ferentiation strategies, this empirical analysis explores integrating service-oriented and data-driven business models as new paths to ensure competitiveness, especially for small and medium-sized enterprises (SMEs). This study aims to capture the current state and challenges associated with the implementation of these business models in this sector. The research was conducted through semi-structured interviews with SMEs in the industry. The findings indicate that service-oriented and data-driven business models are not yet widely adopted and that manufacturing companies re-quire support in their implementation. Fields of action were identified for the industry. These are "Creating awareness and understanding", "Recognizing added value", "In-creasing company maturity" and "Understanding the change process". Cooperation between science and industry is essential in tackling these fields of action to ensure the successful integration of such business models in manufacturing companies. This pa-per identifies challenges in the fields of action that companies must address through a structured approach promoting awareness, recognizing value, improving organiza-tional maturity, and understanding the change process to successfully implement ser-vice-oriented and data-driven business models.

The most aggressive primary malignant brain tumor in adults is glioblastoma (GBM), which has poor overall survival (OS). There is a high relapse rate among patients with GBM despite maxi-mally safe surgery, radiation therapy, temozolomide (TMZ), and aggressive treatment. Hence, there is an urgent and unmet clinical need for new approaches to managing GBM. The current study identified modules (MYC, EGFR, PIK3CA, SUZ12, and SPRK2) involved in GBM disease through the NeDRex plugin. Furthermore, hub genes were identified in a comprehensive interaction network containing 7,560 proteins related to GBM disease and 3,860 proteins associated with signaling pathways involved in GBM. By integrating the results of the aforementioned analyses and performing centrality analysis again, eleven key genes involved in GBM disease were identi-fied. ProteomicsDB or Gliovis databases were used for determining the gene expression in normal or tumor brain tissue. The NetworkAnalyst and the mGWAS-Explorer tools identified miRNAs, SNPs, and metabolites associated with these 11 genes. Moreover, a literature review of recent studies revealed other lists of metabolites related to GBM disease. The enrichment analysis of iden-tified genes, miRNAs, and metabolites associated with GBM disease was done using ExpressAna-lyst, miEAA, and MetaboAnalyst tools. Further investigation of metabolite roles in GBM was done through the pathway, joint pathway, and network analyses. The results of this study identified 11 genes (UBC, HDAC1, CTNNB1, TRIM28, CSNK2A1, RBBP4, TP53, APP, DAB1, PINK1, and RELN), five miRNAs (hsa-mir-221-3p, hsa-mir-30a-5p, hsa-mir-15a-5p, hsa-mir-130a-3p, hsa-let-7b-5p), six metabolites (HDL, N6-acetyl-L-lysine, cholesterol, formate, N, N-dimethylglycine/xylose and X2. piperidinone) and 15 distinct signaling pathways that play an indispensable role in the GBM disease development. To establish early diagnostic methods and plan personalized GBM treatment strategies, the identified top genes-miRNAs and metabolite signatures can be targeted.

In this article we investigate the role of “Renewable Energy Consumption” in the context of Circular Economy. We use data from the World Bank for 193 countries in the period 2011-2020. We perform several econometric techniques i.e., Panel Data with Fixed Effects, Panel Data with Random Effects, Pooled OLS, WLS. Our results show that “Renewable Energy Consumption” is positively associated among others to “Cooling Degree Days” and “Adjusted savings: net forest depletion” and negatively associated among others to “GHG net emissions/removals by LUCF” and “Mean Drought Index”. Furthermore, we perform a cluster analysis with the application of the k-Means algorithm optimized with the Silhouette Coefficient and we find the presence of two clusters. Finally, we compare eight different machine learning algorithms to predict the value of Renewable Energy Consumption. Our results show that the Polynomial Regression is the best algorithm in the sense of prediction and that on average the renewable energy consumption is expected to growth of 2.61%.

In this study, we investigate the growth of EV ownership among Swedish households. Through detailed socio-economic data and the Swedish vehicle register, we are able compare characteristics of households that bought an EV in 2016 with those that became EV owners in 2020. We are thus able to describe and analyse the transition from the early EV owners to the early majority. Unlike many prior studies in the field, which are based on surveys or interviews, this study relies on registry data, thereby encompassing all car owners in Sweden. In this study, we have also scrutinized the significance of ownership mode by distinguishing between households that have chosen to purchase a car and those that have chosen to lease one. The results show that the demand for EVs has reached new consumer groups, e.g. both younger and older car buyers, and that the option to lease a car privately has broadened the market for new cars in general, and for EV’s in particular.

The Chikungunya virus (CHIKV) poses a significant global public health concern, especially in Africa. Since its first isolation in Tanzania in 1953, CHIKV has caused recurrent outbreaks, challenging healthcare systems in low-resource settings. Recent outbreaks in Africa highlight the dynamic nature of CHIKV transmission and the challenges of underreporting and underdiagnosis. Here, we review literature and analyze publicly available cases, outbreaks, and genomic data providing insights into the epidemiology, genetic diversity, and transmission dynamics of CHIKV in Africa. Our analyses reveal the circulation of geographically distinct CHIKV genotypes, with certain regions experiencing a disproportionate burden of disease. Phylogenetic analysis of sporadic outbreaks in West Africa suggests repeated emergence of the virus through enzootic spillover, which is markedly different from inferred transmission dynamics in East Africa, where the virus is often introduced from Asian outbreaks, including the recent reintroduction of the Indian Ocean lineage from the Indian subcontinent to east Africa. Furthermore, there is limited evidence of viral movement between these two regions. Understanding the history and transmission dynamics of outbreaks is crucial for public health planning. Despite advances in surveillance and research, diagnostic and surveillance challenges persist. This review and secondary analysis highlight the importance of ongoing surveillance, research, and collaboration to mitigate the burden of CHIKV in Africa and improve public health outcomes.

Tackling the intricacies of network dismantling in complex systems poses significant challenges. This task has relevance across various practical domains, yet traditional approaches focus primarily on singular metrics, such as the number of nodes in the Giant Connected Component (GCC) or average pairwise connectivity. In contrast, we propose a unique metric that concurrently targets nodes with the highest degree and reduces the GCC size. Given the NP-hard nature of optimizing this metric, we introduce MaxShot, an innovative end-to-end solution that leverages graph representation learning and reinforcement learning. Through comprehensive evaluations on both synthetic and real-world datasets, our method consistently outperforms leading benchmarks in accuracy and efficiency. These results highlight MaxShot’s potential as a superior approach to address the network dismantling problem effectively.

Large Language Models (LLMs) have demonstrated promising capabilities to solve complex tasks in critical sectors such as healthcare. However, LLMs are limited by their training data which is often outdated, the tendency to generate inaccurate ("hallucinated") content and a lack of transparency in the content they generate. To address these limitations, retrieval augmented generation (RAG) grounds the responses of LLMs by exposing them to external knowledge sources. However, in the healthcare domain there is currently a lack of systematic understanding of which datasets, RAG methodologies and evaluation frameworks are available. This review aims to bridge this gap by assessing RAG-based approaches employed by LLMs in healthcare, focusing on the different steps of retrieval, augmentation and generation. Additionally, we identify the limitations, strengths and gaps in the existing literature. Our synthesis shows that proprietary models such as GPT-3.5/4 are the most used for RAG applications in healthcare. Also, there is a lack of standardized evaluation frameworks for RAG-based applications. In addition, the majority of the studies do not assess or address ethical considerations related to RAG in healthcare. It is important to account for ethical challenges that are inherent when AI systems are implemented in the clinical setting. Lastly, we highlight the need for further research and development to ensure responsible and effective adoption of RAG in the medical domain.

This study investigates the transformative impact of ChatGPT, a cutting-edge AI language model developed by OpenAI, on the financial sector. We explore ChatGPT's applications in financial analysis, focusing on its ability to perform tasks traditionally handled by human analysts. By creating a set of multi-step and advanced reasoning financial tasks, and establishing several task-specific evaluation metrics, our experimental results demonstrate that ChatGPT-4o can effectively perform both basic and some complex financial analysis tasks comparable to those executed by humans. However, our empirical evaluation reveals limitations in its performance on complex tasks that require comprehensive understanding and critical thinking. The study highlights the necessity for meticulous task formulation and robust evaluation to achieve consistent functionality. While ChatGPT enhances efficiency in financial analysis, its integration with human expertise remains crucial for effective decision-making. This study contributes to the understanding of AI's role in finance and provides insights into its potential and constraints, guiding future integration of AI technologies in financial practices.

Industrial Control Systems (ICS) are integral to managing and optimizing processes in various industries, including manufacturing, power generation, and more. However, the scarcity of widely adopted ICS datasets hampers research efforts in areas like optimization and security. This scarcity arises due to the substantial cost and technical expertise required to create physical ICS environments. In response to these challenges, this paper presents a groundbreaking approach to generating synthetic ICS data through a data-driven ICS network simulation. We circumvent the need for expensive hardware by recreating the entire ICS environment in software. Moreover, rather than manually replicating the control logic of ICS components, we leverage existing data to autonomously generate control logic. The core of our method involves the stochastic setting of setpoints, which introduces randomness into the generated data. Setpoints serve as target values for controlling the operation of the ICS process. This approach enables us to augment existing ICS datasets and cater to the data requirements of machine learning-based ICS intrusion detection systems and other data-driven applications. Our simulated ICS environment employs virtualized containers to mimic the behavior of real-world PLCs and SCADA systems, while control logic is deduced from publicly available ICS datasets. Setpoints are generated probabilistically to ensure data diversity. Experimental results validate the fidelity of our synthetic data, emphasizing its ability to closely replicate temporal and statistical characteristics of real-world ICS networks. In conclusion, this innovative data-driven ICS network simulation offers a cost-effective and scalable solution for generating synthetic ICS data. It empowers researchers in the field of ICS optimization and security with diverse, realistic datasets, furthering advancements in this critical domain. Future work may involve refining the simulation model and exploring additional applications for synthetic ICS data.

Accurate traffic simulation models play a crucial role in developing intelligent transport systems that offer timely traffic information to users and efficient traffic management. However, calibrating these models to represent real-world traffic conditions accurately poses a significant challenge due to the dynamic nature of traffic flow and the limitations of traditional calibration methods. This article introduces a machine learning-based approach to calibrate macroscopic traffic simulation models using real-time traffic video stream data. By leveraging computer vision technologies to extract key traffic parameters from video streams, the approach demonstrated a notable improvement in aligning the generated data from the calibrated simulation model with car sensor data, achieving an average improvement of over 50% compared to the uncalibrated macroscopic model. Moreover, there was a substantial reduction in data drift for the machine learning model integrated into the virtual transport space using vehicle-to-everything technology, resulting in a more than fourfold decrease in the average absolute error of the model.

Vibration monitoring is a critical aspect of assessing the health and performance of machinery and industrial processes. This study explores the application of machine learning techniques, specifically the Random Forest (RF) classification model, to predict and classify chatter—a detrimental self-excited vibration phenomenon—during machining operations. While sophisticated methods have been employed to address chatter, this research investigates the efficacy of a simplified RF model. The study leverages simulated vibration data, bypassing resource-intensive real-world data collection, to develop a versatile chatter detection model applicable across diverse machining configurations. The feature extraction process combines time-series features and Fast Fourier Transform (FFT) data features, streamlining the model while addressing challenges posed by feature selection. By focusing on the RF model’s simplicity and efficiency, this research advances chatter detection techniques, offering a practical tool with improved generalizability, computational efficiency, and ease of interpretation. The study demonstrates that innovation can reside in simplicity, opening avenues for wider applicability and accelerated progress in the machining industry.

Health information technology has been widely used in healthcare, which has contributed a huge amount of data. Health data has four characteristics: high volume; high velocity; high variety and high value. Thus, they can be leveraged to i) discover associations between genes, diseases and drugs to implement precision medicine; ii) predict diseases and identify their corresponding causal factors to prevent or control the diseases at an earlier time; iii) learn risk factors related to clinical outcomes (e.g., patients’ unplanned readmission), to improve care quality and reduce healthcare expenditure; and iv) discover care coordination patterns representing good practice in the implementation of collaborative patient-centered care. At the same time, there are major challenges existing in data-driven healthcare research, which include: i) inefficient health data exchanges across different sources; ii) learned knowledge is biased to specific institution; iii) inefficient strategies to evaluate plausibility of the learned patterns and v) incorrect interpretation and translation of the learned patterns. In this paper, we review various types of health data, discuss opportunities and challenges existing in the data-driven healthcare research, provide solutions to solve the challenges, and state the important role of the data-driven healthcare research in the establishment of smart healthcare system.

Over the past decade and a half, dynamic functional imaging has revolutionized the neuroimaging field. Since 2009, it has revealed low dimensional brain connectivity measures, has identified potential common human spatial connectivity states, has tracked the transition patterns of these states, and has demonstrated meaningful alterations in these transition and spatial patterns in neurological disorders, psychiatric disorders, and over the course of development. Recently, researchers have begun to analyze this data from the perspective of dynamic system and information theory in the hopes of understanding how these dynamics support less easily quantified processes, such as information processing, cortical hierarchy, and consciousness. Consciousness, in particular, appears to be strongly linked to entropy production in the brain. Little attention has been paid to the effects of psychiatric disease on entropy production in the human brain, however. Even disorders characterized by substantial changes in conscious experience have not been widely analyzed from this perspective. We begin to rectify this by examining the complexity of subject trajectories in state space through the lens of information theory. Specifically, we identify a basis for the dynamic functional connectivity state space and track subject trajectories through this space over the course of the scan. The dynamic complexity of these trajectories is assessed along each dimension of the proposed basis space. Using these estimates, we demonstrate that schizophrenia patients display substantially simpler trajectories than demographically matched healthy controls, and that this drop in complexity concentrates along specific dimensions. We also demonstrate that entropy generation in at least one of these dimensions is linked to cognitive performance. Overall, results suggest great value in applying dynamic systems theory to problems of neuroimaging and reveal a substantial drop in the complexity of schizophrenia patients’ brain function.

With the increasing use of data-driven modeling methods new approaches to complex problems in the field of wind energy can be addressed. Topics reviewed through literature include wake modeling, performance monitoring and controls applications, condition monitoring and fault detection, and other data-driven research. Literature shows the advantages of data-driven methods reduce computational expense or complexity, particularly in the cases of wake modeling and controls, as well as various data-driven methodologies’ aptitude for predictive modeling and classification, as in the cases of fault detection and diagnosis. Significant work exists for fault detection while less work is found for controls applications. A methodology for creating data-driven wind turbine models for arbitrary performance parameters is proposed. Results are presented utilizing the methodology to create wind turbine models relating active adaptive twist to steady-state rotor thrust as a performance parameter of interest. Resulting models are evaluated by comparing root-mean-square-error (RMSE) on both the training and validation data sets, with Gaussian Process Regression (GPR), deemed an accurate model for this application. The resulting model undergoes particle swarm optimization to determine the optimal aerostructure twist shape at a given wind speed with respect to the modeled performance parameter, aerodynamic thrust load. The optimization process shows an improvement of 3.15% in thrust loading for the 10 MW reference turbine, and 2.66% for the 15 MW reference turbine.

Regulation of the diet in terms of the content of soluble and insoluble fibre is of great importance from the point of view of dietetics, microbiology of the gastrointestinal tract and immunology of the organism. Dietary fibre plays an important role in maintaining the balance between the con-tinuity of gut mucus production (intestinal mucosa), the stability of the intestinal microbiome composition, the regeneration of the intestinal epithelium and the immune status within the gut-associated lymphoid tissue (GALT) are played by pectin and their metabolic products in the form of pectin oligosaccharides. The main purpose of this review was to focus on pectin, their functions, their impact on the human's health and on some of the most promising prebiotics due to their solubility in the gastrointestinal tract in the form of pectin oligosaccharides. They have the properties of pectin, but have also additional features and postbiotics obtained in fermentation process can affect the intestinal microbiome and GALT-related immunity. They can be obtained from plant agro-wastes.

This research introduces a hybrid feature extraction approach that combines Linear Discriminant Analysis (LDA) and Multilayer Perceptron (MLP) methods to address the challenges of reducing feature vector dimensionality and accurately classifying smartphone-based human activities. Moreover, to refine activity classification accuracy, Support Vector Machine (SVM) optimization with Stochastic Gradient Descent (SGD) is employed. LDA, a statistical tool, is leveraged to derive a new feature space for data projection, enhancing class separation and test feature label prediction. The proposed approach, named LMSS, was evaluated using the UCI-HAR dataset and compared with state-of-the-art models. The results demonstrate that the proposed approach outperformed the best-performing method over this dataset. It achieved an accuracy rate of 99.52%, precision of 99.55%, recall of 99.53%, and an F1-score of 99.54%, highlighting the effectiveness of the proposed method in accurately classifying the data.

The Chinese community is one of the main minorities in Colombia, and although China has made advances in public health, it faces a growing burden of cardiovascular diseases. This study focuses on evaluating cardiovascular risk factors in Chinese immigrants in Barranquilla, Colombia, due to the lack of specific data on this population. Methods: A cross-sectional study was conducted with 67 Chinese immigrants over 18 years of age residing in Barranquilla. Sociodemographic, anthropometric, clinical, and biochemical data were collected through structured interviews and medical record reviews. Cardiovascular risk was estimated using the 10-year ASCVD (Atherosclerotic Cardiovascular Disease) formula from the ACC/AHA. Statistical tests were employed to assess significant differences and relationships between variables. Results: The sample included 54% women with an average age of 53 years. 75% were over 45 years old, with the main occupations being trade (43%) and homemaking (40%). 54% had social security. Significant differences were observed in systolic blood pressure and the prevalence of smoking and alcoholism between men and women. Women had higher levels of HDL and lower creatinine, while men had higher levels of hemoglobin and creatinine. Cardiovascular risk was high in 9% of cases, moderate in 39%, and low in 52%. Conclusions: Chinese immigrants in Barranquilla present a significant prevalence of cardiovascular risk factors influenced by their socioeconomic situation and barriers to accessing healthcare. Interventions should focus on improving access to healthcare services and promoting healthy lifestyles for this vulnerable community.

1) Background: Capturing patients’ medical histories significantly influences clinical decisions. Errors in this process lead to clinical errors, increase costs and dissatisfaction among physicians and patients. Physicians in developing countries are overloaded with patients and cannot always follow the proper history-taking procedure. The challenges are acknowledged; however, a comprehensive understanding of the status and the remedies remained unexplored. 2) Objective: This paper aims to investigate the workload, history-taking challenges, and the willingness of the physicians to accept digital solutions. 3) Methods: A cross-sectional online survey was conducted on 104 physicians across Bangladesh, featuring 22 questions regarding their professional environment, workload, digitization status of health records, challenges in history-taking, and attitudes toward adopting digital solutions for managing patient histories; 4) Results: 92.67% of the physicians face workloads, 88.46% struggle in medical history-taking, and only 4.81% use digital medical records. About 70% struggle to complete the necessary history-taking steps, emphasizing the urgent need for solutions. An AI-based Smart Health Gantt Chart (SHGC) system has been introduced for their instant feedback. 93.27% of physicians expressed their willingness to use such a system. 5) Conclusions: The proposed SHGC has the potential to enhance healthcare efficiency in developing nations, benefit physicians, and improve patient-centered care.

In this paper, we first discuss the research status and application progress of the finite element method and the smoothed particle method. By analyzing the advantages of the smoothed particle method and the finite element method, a new coupling algorithm, namely FEM-SPH algorithm, is proposed. By the method of comparison, it shows that finite element method and SPH method in the simulation of large deformation problems each have advantages and disadvantages, the finite element method smoothed particle coupling algorithm is effective to achieve the performance of high computational efficiency and can naturally simulate large deformation problems across. In the process of calculation, the large deformation unit can be freely into an algorithm to facilitate the calculation accuracy and efficiency of three methods of numerical simulation. Through the study found, FEM-SPH algorithm not only overcome the defect of smooth particle tensile instability, but also overcomes the problem of low efficiency of finite element computation. To further test the FEM-SPH algorithm has advantages in the practical engineering, we have carried out the actual test to the example of the super high speed collision, concluded that, since the target of most of the computational domain is always finite element, smoothed particle focused only in contact with the projectile and target of local area, particle number is not much, the whole calculation process just ten minutes, computational efficiency has been greatly improved, at the same time in the simulation of large deformation, the advantage is very obvious .This provides a criterion for the actual project, depending on the specific material deformation mode and choose a more appropriate conversion algorithm.

The paper presents the problem of damage detection in steel girders. Static displacements at the selected point of the structure play the role of measured variables. Structural response signal decomposition is performed according to the Mallat pyramid algorithm, which is used to perform the discrete wavelet transform (DWT). This procedure allows us to quite well determine the location of structural damage. The geometry and the placement of any defective part of the structure may have a random character. It can be assumed that the random processes occurring in the broadly understood structure mechanics are Gaussian in nature. The first four probabilistic moments are estimated using three approaches independent: semi-analytical (SAM), perturbative (SPT), and Monte-Carlo simulations (MCS). The semi-analytical random approach seems to be the most optimal due to the necessary computation time. The incorporation of the mathematical stochastic apparatus into the classical (deterministic) analysis of the statics of the structure makes it possible to estimate the reliability measures of the analyzed girder.

The COVID-19 pandemics has had an unprecedented global impact, and the COVID-19 mass vaccination campaign has been commonly regarded as crucial to overcome the pandemics. Since all-cause mortality is the best way to measure the consequences of a health intervention, the present study was devised to analyze the all-cause mortality data of the United Kingdom (UK), which are made publicly available broken down by vaccination status. Data from April 2021 to May 2023 were retrospectively collected and analyzed according to age groups and vaccination status and the Standardized Mortality Ratio (SMR) for all-cause mortality and for non-COVID-19 were calculated in comparison to the corresponding unvaccinated groups. Results show that, since an age group dependent date, the all-cause mortality SMRs were increasing in any of the age groups considered. Initially, the all-causes death SMRs were less than 1 for all age groups, but due to their growth, for the age groups 18-39, 80-89 and 90+ years by a certain date they exceeded the reference value. For the other age groups, as long as the trend is maintained, it is possible to predict the date in which the SMR would reach the value 1. Non-COVID-19 SMR values show a very similar trend. Their initial values much lower than 1 suggest the presence of significant biases in the ONS dataset which lead to an underestimation of the risks for those vaccinated, as it is not plausible that the vaccine protects from causes other than COVID-19. The finding that all-cause mortality SMRs in vaccinated in comparison to unvaccinated people increases over time requires careful examination to understand the underlying factors. Meanwhile, the other major countries should undertake a systematic collection of all-causes mortality broken down by vaccination status, and should be implemented a moratorium of the promotion of mass vaccination campaigns.

As previous study in many countries shown that stroke patient onsets are not distributed randomly, but associate with meteorological factors. However, the relationship between stroke occurence and meteorological factors remain unknown in mountain area in Guizhou China. This paper firstly introduces multi-source fusion data which is integrated by the mountain meteorological factor, geographic mapping elevation information data and stroke population monitoring of Guizhou province. Mainly elaborates from a few aspects, which concludes data collection, data sorting, data extraction, data cleaning and data production in detail. A completed and detailed meteorological stroke data set was successfully established and multi-source data fusion was realized by the use of Gbase and unified data service interface of Guizhou meteorological big data cloud platform. And we report the impact of meteorological variables in Guizhou mountain area climate on stroke. In this study, we performed a statistical fusion data between January 2017 and December 2020 about stroke incidence rate and meteorological factors respectively, for instance, concerning the mean (Mean), maximum (Max), minimum (Min), median (Median), standard deviation (Std) . We calculated stroke rates (date stroke occurence)/(year stroke occurence) and we investigated the distribution of days included in the label. Results: the distribution of the incidence rate basically conforms to the normal distribution with the label Max 0.007399, label Min 0.000204, label Mean 0.002738, label Median 0.002643, label Std 0.00076. We observed a positive significant correlation of stroke incidence rate directly proportional to the daily temperature difference (between 0 and 20 degrees Celsius), as the value of this factor exhibits variation larger, the incidence rate is gradually increasing. And we investigated from the Pearson correlation coefficients that stroke incidence increasing when meteorological factors at low humidity (less than 40% (RH 80%), temperature higher than 31℃); the 24-hour daily temperature difference varies between 6 and 10℃ (6

The ASEAN Community-based Tourism (CBT) Standard has been adopted by 10 ASEAN member states in 2016 in order to collectively promote ASEAN as a competitive community-based tourism destination. Among the ASEAN member states, Lao PDR (Laos), has a unique CBT development experience through collaboration with various international development agencies. Such history has brought about issues when ASEAN CBT Standard was implemented at to provincial and district levels in Laos, including concerns of related communities on the Standard being not easily applicable considering the state of tourism development. While the application of the regional standard is a significant issue to the tourism industries in the Member States, however, there has been a lack of studies regarding the dynamics of implementation of regional tourism standards at the national level. In order to fill the research gap, this study utilized in-depth interviews with seven executives with significant experiences from the government, international development agency, international organization, and the private sector. Interviewees projected a diversity of perspectives on enabling factors and challenges in implementing ASEAN Community-based Tourism Standard at the national level focusing on Laos, which showed the complexity of CBT dynamics. The results also revealed how regional standards can be further recognized and promoted to the key stakeholders of Laos, better accepted and utilized by end users, and possibly better customized according to the local circumstances. Findings of this study evidence that collaboration among key stakeholders and the expected role of these stakeholders are critical when implementing ASEAN CBT Standard.

Previous high throughput screening studies indicated trans-eQTLs tend to be tissue specific. In this study, I probed if this feature can be used to identify tissue-specific gene regulatory networks. eQTL data (P<5e-8) for 16,259 genes were identified and their summary association statistics were obtained from the eQTLGene database. Next, eQTLs that display both cis and trans regulatory effects were selected and the association between their corresponding genes were examined using Mendelian randomization. A total of 169 genes that exerted trans-regulatory impacts on 692 genes were identified. 90% of the genes (N=749) aggregated into a gene regulatory network significantly enriched in hemo-immune processes. The robustness of finding was confirmed through simulation. The identified network displayed the scale-free topology. This provided the reason to examine the association of the network’s hub genes with the phenome. The outcome of analyses revealed GSDMB and ORMDL3 impact several disorders of immune origin and ALDH2 overexpression contributes to obesity. This study reports trans-eQTLs can be used to identify tissue-specific gene regulatory networks and describes a workflow to achieve this purpose. The network identified in this study showed scale-free topology indicating the hub genes of a GRN could be targeted to prevent disease outcomes.

Accurate diagnosis for the 400 million people with rare diseases is critical for healthcare decisions, prognosis, understanding disease mechanisms, and identification of treatments. Despite advances in genome sequencing, barriers such as high interpretation costs, diagnostic expertise, throughput associated delays, and uncertain variant classifications persist, with demand exceeding capacity. Many variant classification methods focus narrowly on specific consequences, leading to the use of complex integrative pipelines that often overlook transcript variability and lack prediction transparency. To overcome these limitations, we introduce DITTO. This transparent, transcript-aware machine-learning method demonstrates superior overall performance in accuracy, recall, and precision when compared to existing tools. DITTO is publicly available at https://github.com/uab-cgds-worthey/DITTO

Timely and accurate information on tree species is crucial for the sustainable management of natural resources, forest inventory, biodiversity detection, and carbon stock calculation. The advancement of remote sensing technology and artificial intelligence has facilitated the acquisition and analysis of remote sensing data, resulting in more precise and effective classification of tree species. Multimodal remote sensing data and deep learning seem to be the current tree species classification research mainstream, whether or not. The current review on the remote sensing data and deep learning tree species classification methods perspectives to analyze the unimodal and multimodal remote sensing data and classification methods in this realm is missing. To bridge the gap, we search for major trends in the remote sensing data and tree species classification methods, provide a detailed overview of classic deep learning-based methods for tree species classification, and discuss the limitations.

We propose an innovative approach called SMPTC3, designed specifically to enhance security and privacy in cross-chain transaction verification. This approach addresses multi-chain, multi-participant information exchange and large-scale cross-chain transfers, resisting various types of malicious attacks. We leverage the verifiability of cross-chain transactions based on smart contracts and innovatively transform transaction information into confidential sets, organizing them into quadratic secret polynomials. By utilizing secret sharing and random distribution techniques, we construct a secure multiparty computation method, tailored for cross-chain transactions. To enhance the efficiency of cross-chain transactions, we introduce cross-chain batch processing technology, grouping inter-chain transactions into cross-chain transaction sets. Unlike traditional distributed notary technologies, SMPTC3 designates honest participants as a cross-chain notary group, reducing the time required for redundant signature confirmations and significantly lowering the possibility of malicious notaries. Theoretical analysis and empirical experiments demonstrate that SMPTC3 is highly efficient in addressing cross-chain transaction security issues.

In traditional databases, the entity resolution problem (which is also known as deduplication), refers to the task of mapping multiple manifestations of virtual objects to its corresponding real-world entity. When addressing this problem, in both theory and practice, it is widely assumed that such sets of virtual object appear as the result of clerical errors, transliterations, missing or updated attributes, abbreviations, and so forth. In this paper, we address this problem under the assumption that this situation is caused by malicious actors operating in domains in which they do not wish to be identified, such as hacker forums and markets in which the participants are motivated to remain semi-anonymous (though they wish to keep their true identities secret, they find it useful for customers to identify their products and services). We are therefore in the presence of a different, even more challenging problem that we refer to as adversarial deduplication. In this paper, we study this problem via examples that arise from real-world data on malicious hacker forums and markets arising from collaborations with a cyber threat intelligence company focusing on understanding this kind of behavior. We argue that it is very difficult---if not impossible---to find ground truth data on which to build solutions to this problem, and develop a set of preliminary experiments based on training machine learning classifiers that leverage text analysis to detect potential cases of duplicate entities. Our results are encouraging as a first step towards building tools that human analysts can use to enhance their capabilities towards fighting cyber threats.

In power systems there are complex transformer structures, whose accurate analysis is not possible using the techniques available today. This paper presents a systematic data driven analysis method for coupled inductors of arbitrary complexity. The method first establishes a winding matrix N mapping the windings to the limbs of the transformer. A permeance matrix P is created from the reluctance network of the magnetic core. A generalized inductance matrix L mapping currents in the transformer windings to the induced voltages is generated based on the winding (N) and permeance (P) matrices. The inductance matrix representation of a coupled inductor is then transformed to an admittance matrix, which can be integrated to the nodal analysis of the electrical circuit surrounding the coupled inductor. The method presented is validated by simulations with real transformer structures using electromagnetic transient program (EMTP/ATP).

Increasing efforts have been devoted to promoting sustainable demolition waste management (DWM) from a life cycle-thinking perspective. To this end, facilitating sustainability-oriented de-cision-making for DWM planning requires a sustainability assessment framework for assessing multifaceted criteria. This study develops a BIM-based DWM sustainability assessment ap-proach to facilitate the life cycle assessment (LCA) and decision-making by coupling the enriched IFC model with hybrid Multi-Criteria Decision-Aiding (MCDA) methods using Dynamo visual scripting. To streamline the data-intensive LCA process, this study enriched the BIM properties and accommodated them into the LCA data template to enhance data interoperability, thus achieving seamless data transfer. Moreover, hybrid MCDA methods are integrated into the deci-sion-making workflow for DWM scenario ranking. A pilot study is employed to verify the ap-plicability of the decision-aiding framework. The results unveil that the sustainability score ascended with the recycling rate. The optimal DWM alternative with the highest recycling rate yields the highest sustainability score at 91.63. Conversely, a DWM alternative reflecting the ‘status quo’ in China’s recycling industry has the lowest score at 8.37, significantly lower than the baseline scenario with a 50% recycling rate. It is worth noting that the ‘growth curve’ of the sustainability score continuously flattens as the target recycling rate escalates. The increment in recycling rate from the “Australian standard” scenario to the optimal scenario is 18.4%, while the sustainability score merely increases by 2.3%, signal-ling that the former scenario arrived at an optimum point for maximising the cost-efficiency of DWM under the predefined framework and contexts.

As the demand of heating and air conditioning is increasing day by day due to getting a comfortable life, for that reason, the market for heat pump and air conditioning systems or both, is seeing a steady increase in low global warming potential. All researchers on heat pump and air conditioning systems are searching for environmentally friendly refrigerants. However, a significant number of contemporary refrigerants (HCFCs) have the potential to cause global warming and ozone depletion, such as those found in heat pump air conditioning systems. Using more environmentally friendly refrigerants, including hydrocarbon and blend refrigerant mixtures, is one way to lower GWP and Ozone depletion potential. This study examines the performance of several alternative refrigerants, including R32, R134A, R410A, R22, and R290. In order to examine the performance of R290, theoretical and simulation results are compared on various refrigerants while taking into account a number of performance parameters, including the refrigerant energy efficiency ratio, mass flow rate, coefficient of performance, cooling capacity, and compressor work for one ton of refrigeration (1TR) air conditioners. One player with a very low GWP is R290. However, the only drawback is that it can catch fire and is hazardous to use in split-type commercial heat pump air conditioning applications. The environmental and thermo physical properties of HC-290 are significantly better than those of other materials, according to theoretical and simulation studies utilizing Cool Pack software, hence it is a viable replacement.

Plant Factory Transplanter (PFT) is a key component of the plant factory system. Its operation status directly affects the quality and survival rate of planted seedlings, which in turn affects the overall yield and economic efficiency. To monitor the operation status and transplanting quality of a transplanting machine in a timely manner, the primary task is to use a computerized and easy-to-use method to monitor the transplanting units. Inspired by the latest developments in augmented reality and robotics, a DT model-based and data-driven online monitoring method for plant factory transplanting equipment is proposed. First, a data-driven and virtual model approach is combined to construct a multi-domain digital twin of the transplanting equipment. Then, taking the vibration frequency domain signal above the transplanting manipulator and the image features of the transplanting seedling tray as input variables, the evaluation method and configuration method of the PFT digital twin system are proposed. Finally, the effect of the transplanter is evaluated, and the cycle can be repeated to optimize the transplanter to achieve optimal operation parameters. The results show that the digital twin model can effectively use the sensor data to identify the mechanical vibration characteristics and avoid affecting transplanting quality due to mechanical resonance. At a transplanting rate of 3000 plants/h, the transplanting efficiency can be maintained at a high level and the vibration signal of X, Y, Z-axis above the transplanting manipulator is relatively calm. In this case, Combined the optimal threshold method with the traditional Wiener algorithm, the identification rate of healthy potted seedlings can reach 94.3%. Through comprehensively using the optimal threshold method and 3D block matching filtering algorithm for image threshold segmentation and denoising, the recognition rate of healthy seedlings has reached over 96.10%. In addition, the developed digital twin can predict the operational efficiency and optimal timing of the detected transplanter, even if the environmental and sensor data are not included in the training. The proposed digital twin model can be used for damage detection and operational effectiveness assessment of other plant factory equipment structures.

Enhancing energy efficiency within the building sector is imperative to curbing energy losses, given that this sector alone contributes to over 34% of global energy consumption. Employing a building management system, along with its regular updates, presents a strategic avenue to decrease energy usage, enhance building energy efficiency, and more. Tailored control strategies, aligned with the unique characteristics and usage patterns of each building, are essential for achieving energy savings. This article presents an evaluation of HVAC system efficiency in office buildings, utilizing a data-driven approach coupled with simulations conducted in IDA ICE software. The research explores the control strategy of an office building equipped with a constant air volume HVAC system, featuring a regularly controlled air handling unit. The objective is to boost energy efficiency while striking a balance between occupant comfort and energy consumption. Findings indicate that by analyzing measured data and adjusting configurable parameters, building energy consumption can be significantly reduced. Close monitoring of indoor parameters by building operators and corresponding adjustments to the HVAC system can yield energy savings of up to 16%. Leveraging these insights, the paper suggests integrating data-driven and dynamic simulation methods into building management system models to optimize HVAC systems, enhance energy efficiency, and advance ambitious carbon neutrality objectives.

Questionnaires for self-report of food-elicited emotions are an established practice in consumer studies. However, most tools are originally developed in English and translated into other languages, which limits their use. The aim of this study was to develop the first Greek emotion lexicon and measurement tool for consumers, using standard methodology and extending it. The lexicon was compiled using linguistic sources and extended using the World Wide Web and a popular social media platform for the collection of authentic language and usage data. Terms were also collected from consumers using questionnaires and a variety of stimuli. Terms collected from consumers only comprise: healthy, distrustful, curious, childish, impressed, tolerant, impatient It was validated by application in various case studies, providing discrimination across and within food categories, and by comparison to the Greek translation of a standard tool in English, the EsSense Profile. The comparison was conducted by measuring emotions elicited by six food categories and demonstrated that it is preferable to use emotion measurement tools developed in the linguistic and cultural context of intended use, as they convey consumers’ emotions naturally and more accurately. This tool can be used as a Check- or Rate- All-That-Apply questionnaire to measure consumer responses to food categories and products. The methodology and validation presented can be applied for the compilation of emotion lexicons in languages less studied than English.

In the realm of Lithium-ion batteries, issues like material aging and capacity decline contribute to performance degradation or potential safety hazards. Predicting Remaining Useful Life (RUL) serves as a crucial method to assess the health of batteries, thereby enhancing reliability and safety. Currently hybrid approaches for batteries RUL estimation are prevalence and gained fruitful development. In this paper, a hybrid voting ensembles combining Gradient Boosting, Random Forest and K-Nearest Neighbors is proposed to predict the capacity fade trend and knee point. Finally, extensive experiments are conducted using CALCE CS2 datasets. According to the experimental results, the proposed approach supersedes the single deep learning approach for RUL prediction and the knee point is predicted accurately. Besides prediction purpose, this innovated approach can be also proposed to be integrated into the real-world application for wider usage.

The development of new turbomachinery designs requires numerous time-consuming and computationally intensive computational fluid dynamics (CFD) calculations. However, most of the generated high spatial resolution data remains unused at later development steps. That is also the case with automated optimization processes that use only a few integral values to determine objectives and constraints. Therefore the development of a data-driven AI model was initiated to ensure the potential of further use of the CFD data which is also used to train the AI model. The presented method subsequently provides a fast approximation of the 3D flow for new designs. In this paper, the structure of the developed AI model is presented and the approximation quality is analysed using a complex, state-of-the-art compressor test case. It is shown that the AI model can reproduce many characteristics of the 3D flow of new designs, and performance measures such as efficiency can be derived from these flow predictions. In addition, the complex test case revealed that greater design variation reduces the AI approximation quality which can lead to undesirable exploratory behaviour in an optimisation setup. Overall, the test case has shown promising results and has provided hints for further improvements of the AI model.

Cycle times at workstations in offsite construction factories fluctuate widely due to various influencing factors. Consequently, relying on average rates, such as length per unit of time, for estimating cycle times proves to be inaccurate, often leading to significant deviations between production schedules and actual operations. To address this issue, this study proposes an estimation system that leverages machine-learning-based prediction, statistical methods, 3D simulation, and computer vision to predict cycle times at the workstation level. Testing of the system on a semi-automated wood-wall framing workstation in a panelized construction factory shows that it reduces the mean absolute error and sum of errors by approximately 36% and 68%, respectively, compared to the fixed rate method. The results also highlight the efficacy of using computer vision data for training machine-learning models for cycle time estimation, the importance of identifying and understanding the factors influencing cycle times, and the impact of random delays on the accuracy of cycle time estimation systems.

The abstract should be a total of about 250 words and structured to contain the following headings: Background/Objectives, Methods, Results, Conclusions. Background/Objectives: Place the question addressed in a broad context and highlight the purpose of the study; Methods: Describe briefly the main methods or treatments applied. Include any relevant preregistration numbers, and species and strains of any animals used; Results: Summarize the article’s main findings; Conclusions: Indicate the main conclusions or interpretations. The abstract should be an objective representation of the article: it must not contain results which are not presented and substantiated in the main text and should not exaggerate the main conclusions. Clinical trial abstracts should include items that the CONSORT group has identified as essential.

Confronting the dual challenges of rapid urbanization and climate change, although extensive research has investigated the influencing factors and practical strategies of urban carbon emissions and urban vibrancy, respectively, the unclear mutual nexus between them and the development strategy of collaborative optimization requires further in-depth analysis. This study explores the delicate balance between urban vibrancy and low-carbon sustainability within the confines of Beijing’s Fifth Ring Road. By integrating OpenStreetMap, land use, population, and building carbon emission data, we have developed a reproducible method to estimate total carbon emission and emission intensity per capita. Furthermore, we have introduced vibrancy index data to distinguish the vibrancy evaluation of residential and non-residential land and applied cross-combinational classification technology to dissect the spatial correlation between urban carbon emissions and urban vibrancy. The results reveal that the four combination typologies show more significant differences and regularity in residential land. Based on the discovery of spatial correlation, this study puts forward corresponding development strategy suggestions for each typology based on geographical location and the requirements of urban development policies of these four combination typologies. In conclusion, our study highlights the importance of integrating carbon emissions and urban vibrancy comprehensively in sustainable urban planning and proposes that various land use combinations need targeted development strategies to achieve this goal, which need to consider population, energy, service facilities, and other diverse aspects.

We generalize the point information gain (PIG) and derived quantities, i.e., point information gain entropy (PIE) and point information gain entropy density (PIED), for the case of the Rényi entropy and simulate the behavior of PIG for typical distributions. We also use these methods for the analysis of multidimensional datasets. We demonstrate the main properties of PIE/PIED spectra for the real data on the example of several images, and discuss further possible utilizations in other fields of data processing.

The effectiveness of a hybrid technique for identifying seismic damage in planar, multistory, steel X or V-braced frames is demonstrated here through an example of a six-story frame. This proposed technique, referred to as “M and P”, combines the instrumental Monitoring (M) with Pushover analysis (P). According to the methodology, the diagram of stepping eigenfrequencies of the frame in the inelastic region is initially plotted against seismic roof displacement. The fundamental natural frequency detected via the monitoring process is then utilized in this key diagram to reveal the inelastic roof displacement that corresponds to the damage state of the steel braced frame. This displacement is subsequently used as the target in the pushover analysis, facilitating the identification of seismic damage in the existing steel braced frame. Finally, the damage image is correlated with the damage stiffness matrix of the frame at the same inelastic roof displacement. The investigation results indicate that combining instrumental monitoring with pushover analysis enables accurate identification of seismic damage potential in existing steel braced frames.

Gene regulation is vital for cellular function and homeostasis, involving diverse mechanisms controlling specific gene products and contributing to tissue-specific gene expression. Dysregulation leads to diseases, emphasizing the need for understanding these mechanisms. Non-coding regions, notably enhancers and super-enhancers (SEs), act as crucial gene regulators, orchestrating transcriptional activity via transcription factors (TFs). SEs, with high activity, are pivotal in cell identity and disease progression. Current computational approaches focus on individual regulators like TFs and miRNAs, neglecting SE interactions. We emphasize incorporating SEs into models to enhance understanding. Experimental studies have recently linked miRNAs and TFs to SEs. Chromatin immunoprecipitation followed by sequencing (ChIP-Seq) provides valuable SE information. In this review, we categorize computational methods leveraging TF and miRNA data into three areas and explore challenges integrating enhancers/SEs. These include unraveling indirect regulatory networks, identifying network motifs, and enriching pathway identification by dissecting gene regulators, including SEs. We hypothesize that addressing these challenges will enhance our understanding of gene regulation, aiding in identifying therapeutic targets and disease biomarkers. We believe that understanding the role of ChIP-Seq data in predicting the effect of miRNA on gene regulation is crucial to construct statistical/computational model that would tackle these challenges.

The paper investigates into the intricacies of semiconductor manufacturing, a highly complex process entailing a wide array of subprocesses and diverse equipment. Semiconductors are miniaturized integrated circuits comprising numerous components. The semiconductor manufacturing process begins with the thin disc-shaped silicon wafers. On each wafer, up to thousands of identical chips can be prepared depending upon the diameter of the wafer to build up the circuits layer by layer in a wafer fab. The size of the semiconductors requires a high number of units to be produced, thus necessitating a large amount of data to control for improving the semiconductor manufacturing process. Therefore, the collection and analysis of the equipment data, process data, and machine history data throughout the manufacturing process are required to diagnose faults, monitor the process, and manage the manufacturing process effectively. This research is focused on improving the semiconductor manufacturing process through a rigorous analysis of collected manufacturing process data, employing statistical process control (SPC), data mining techniques, and data-driven decision models. The project's primary objective is to increase the manufacturing process stability and productivity by utilizing the latest data-driven technologies in the scientific community. A structured review was undertaken, exploring contemporary data-driven methodologies in semiconductor manufacturing process improvement, specifically pertaining to process capability, product yield rate, and process stability. This review accentuates a comprehensive evaluation of data-driven methodologies applicable to conventional semiconductor manufacturing facilities, aiming to drive substantial process improvements. It features a detailed demonstration facilitating the selection of optimal semiconductor manufacturing processes to enhance overall operational performance. This study of process improvement in the semiconductor manufacturing steps through the application of data-driven methodologies will be effective in delivering advanced, real-time, and proactive control decisions throughout the manufacturing facilities. This endeavor is expected to promptly provide critical insights for enterprise manufacturing decision-makers to reduce manufacturing cycle time, improve the product yield rate, and increase the overall efficiency of the manufacturing process.

Electroencephalography (EEG) is a brain imaging technique in which electrodes are placed on the scalp. EEG signals are commonly decomposed into frequency bands called delta, theta, alpha, and beta.While these bands have been shown to be useful for characterizing various brain states, their utility as a one-size-fits-all analysis tool remains unclear. We present a two-part data-driven methodology for objectively determining the best EEG bands for a given dataset in this paper. First, a decision tree is used to estimate the optimal frequency band boundaries for reproducing the signal’s power spectrum for a predetermined number of bands. The optimal number of bands is then determined using an Akaike Information Criterion (AIC)-inspired quality score that balances goodness-of-fit with a small band count. Data-driven EEG band discovery may aid in objectively capturing key signal components and uncovering new indices of brain activity.

We present a class of efficient parametric closure models for 1D stochastic Burgers equations. Casting it as statistical learning of the flow map, we derive the parametric form by representing the unresolved high wavenumber Fourier modes as functionals of the resolved variables’ trajectory. The reduced models are nonlinear autoregression (NAR) time series models, with coefficients estimated from data by least squares. The NAR models can accurately reproduce the energy spectrum, the invariant densities, and the autocorrelations. Taking advantage of the simplicity of the NAR models, we investigate maximal and optimal space-time reduction. Reduction in space dimension is unlimited, and NAR models with two Fourier modes can perform well. The NAR model’s stability limits time reduction, with a maximal time step smaller than that of the K-mode Galerkin system. We report a potential criterion for optimal space-time reduction: the NAR models achieve minimal relative error in the energy spectrum at the time step where the K-mode Galerkin system’s mean CFL number agrees with the full model’s.

The study was conducted on applying machine learning and data mining methods to personalizing the treatment. This allows investigating individual patient characteristics. Personalization is built on the clustering method and associative rules. It was suggested to determine the average distance between instances for optimal performance metrics finding. The formalization of the medical data pre-processing stage for finding personalized solutions based on current standards and pharmaceutical protocols is proposed. The model of patient data is built. The paper presents the novel approach to clustering built on ensemble of cluster algorithm with better than k-means algorithm Hopkins metrics. The personalized treatment usually is based on decision tree. Such approach requires a lot of computation time and cannot be paralyzed. Therefore, it is proposed to classify persons by conditions, to determine deviations of parameters from the normative parameters of the group, as well as the average parameters. This made it possible to create a personalized approach to treatment for each patient based on long-term monitoring. According to the results of the analysis, it becomes possible to predict the optimal conditions for a particular patient and to find the medicaments treatment according to personal characteristics.

A new model for international bed numbers is applied to local area populations for English Clinical Commissioning Groups (CCGs) where the Age Standardized Mortality Rate (ASMR) is used as a measure of population health and hence for total occupied hospital bed demand (elective plus emergency admission types, including acute, rehabilitation, mental health, and maternity), rather than simple bed availability. A 100-unit increase in ASMR (European Standard population) leads to a 15.3 – 30.7 (feasible range) unit increase in occupied beds per 1,000 deaths. ASMR shows why the Australian states of the Northern Territory and Tasmania have an intrinsic higher bed demand than the other states – although in both cases the bed planning methodologies failed to indicate this need and both states show a large bed deficit. Due to the high volatility in bed demand the average bed demand for 2019 was determined by a linear trend using data for 2014/15 to 2019/20 — as the pre-COVID-19 baseline. The slope of the relationship between occupied beds per 1,000 deaths and deaths per 1,000 population shows a power law function. As is to be expected there is scatter around the trend line which will partly arise from uncertainty in the expected occupied beds in 2019, fluctuations in both ASMR and deaths per 1,000 population from one year to another, changes in the number of persons on the elective, outpatient and diagnostic waiting lists, and local area variation in births and consequently upon maternity, neonatal and pediatric bed demand. Additional variation in bed demand will arise from differences in the level of funding for social care, especially elderly care, and to a lesser extent upon patients using private health care, and charitable hospices for palliative care. However, after including the change in bed demand arising from ASMR the model is sufficiently accurate to identify gross differences in bed demand as a prelude to further investigation. The model requires further extension to cover specialty-level demand, and perhaps segregation between elective and emergency types of inpatient demand. A method for benchmarking the whole hospital’s average bed occupancy is given which enables them to run at optimum efficiency and safety. Using this method English hospitals can be shown to operate at highly disruptive and unsafe levels of bed occupancy leading to deleterious ‘turn-away’. Turn-away implies bed unavailability for the next arriving patient. The problems associated with crafting effective bed planning are illustrated using the English NHS as an example.

The rapid development of specific-purpose Large Language Models (LLMs), such as Med-PaLM, MEDITRON-70B, and Med-Gemini, has significantly impacted healthcare, offering unprecedented capabilities in clinical decision support, diagnostics, and personalized health monitoring. This paper reviews the advancements in medicine-specific LLMs, the integration of Retrieval-Augmented Generation (RAG) and prompt engineering, and their applications in improving diagnostic accuracy and educational utility. Despite the potential, these technologies present challenges, including bias, hallucinations, and the need for robust safety protocols. The paper also discusses the regulatory and ethical considerations necessary for integrating these models into mainstream healthcare. By examining current studies and developments, this paper aims to provide a comprehensive overview of the state of LLMs in medicine and highlight the future directions for research and application. The study concludes that while LLMs hold immense potential, their safe and effective integration into clinical practice requires rigorous testing, ongoing evaluation, and continuous collaboration among stakeholders.

The digital world has a wealth of data, such as Internet of Things (IoT) data, business data, health data, mobile data, urban data, security data, and many more, in the current age of the Fourth Industrial Revolution (Industry 4.0 or 4IR). Extracting knowledge or useful insights from these data can be used for smart decision-making in various applications domains. In the area of data science, advanced analytics methods including machine learning modeling can provide actionable insights or deeper knowledge about data, which makes the computing process automatic and smart. In this paper, we present a comprehensive view on "Data Science'' including various types of advanced analytics methods that can be applied to enhance the intelligence and capabilities of an application through smart decision-making in different scenarios. We also discuss and summarize ten potential real-world application domains including business, healthcare, cybersecurity, urban and rural data science, and so on by taking into account data-driven smart computing and decision making. Based on this, we finally highlight the challenges and potential research directions within the scope of our study. Overall, this paper aims to serve as a reference point on data science and advanced analytics to the researchers and decision-makers as well as application developers, particularly from the data-driven solution point of view for real-world problems.

The raw material purchasing (RMP) problem is to determine the purchasing quantities of raw materials in given periods or cycles. Raw material purchasing optimization is crucial for large-scale steel plants because it is closely related to the supply of raw materials and cost savings. The raw material purchasing of large-scale steel enterprises is characterized by many varieties, large quantities, and high costs. The RMP objective is to minimize the total purchasing cost consisting of the price of raw materials, purchasing set-up costs, and inventory costs and meet product demand. We present a mixed integer linear programming (MILP) model and a column generation (CG) solution for the resulting optimization problem. The column generation algorithm is the generalization of the branch & bound algorithm with solving the linear programming (LP) relaxation of MILP using column generation (CG), and its advantage is to handle large-sized MILPs. Experimental results show the effectiveness and efficiency of the solution.

The accurate detection of clouds is an important first-step in the processing of remotely sensed satellite data analyses and subsequent cloud model predictions. While initial cloud retrieval technology began with the exploitation of one or two bands of satellite imagery, it has accelerated rapidly in recent years as sensor and retrieval technology have exploded, creating a new era in space exploration. Additionally, initial emphasis in satellite retrieval technology focused on cloud detection for cloud forecast models, more recently cloud screening in satellite acquired data is playing an increasingly critical role in the investigation of cloud free data for the retrieval of soil moisture, vegetation cover, ocean colour concentration and sea surface temperatures, as well as environmental monitoring of a host of products, e.g. atmospheric aerosol data, to study the Earth’s atmospheric and climatic systems. With about 60% of the Earth covered by clouds, on average, it is necessary to both accurately detect clouds in remote sensing data to screen cloud contaminate data in remote sensing analyses. In this paper, the evolution of cloud detection technology is highlighted with advancement in sensor hardware technology and possible AI algorithmic advances. Additionally, a discussion is presented on methods to obtain the cloud truth data needed to determine the accuracy of these cloud detection approaches.

In an era of unparalleled technical advancement, the pharmaceutical industry is struggling to transform data into increased research and development efficiency, and as a corollary, new drugs for patients. Here, we briefly review some of the commonly discussed issues around this counterintuitive innovation crisis. Looking at both industry and science related factors, we posit that traditional preclinical research is front-loading the development pipeline with data and drug candidates that are unlikely to succeed in patients. Applying a first principles analysis, we highlight the critical culprits and provide suggestions as to how these issues can be rectified through pursuit of a Human Data-driven Discovery (HD3) paradigm. Consistent with other examples of disruptive innovation, we propose that new levels of success are not dependent on new inventions, but rather the strategic integration of existing data and technology assets. In support of these suggestions, we highlight the power of HD3, through recently published proof-of-concept applications in the areas of drug safety analysis and prediction, drug repositioning, rational design of combination therapies and the global response to the Covid19 pandemic. We conclude that innovators must play a key role in expediting the path to a largely human focused, systems-based approach to drug discovery and research.

The paper delves into the critical issue of damage detection within the guy cable of a truss steel mast, a pivotal component in structural integrity. It introduces a model wherein damage manifests as a localized cross-section reduction in a single element of the cable. Employing Discrete Wavelet Transform (DWT), a pioneering methodology, the study scrutinizes the behavior of the affected elements through static structural analyses. Signal decomposition via the Mallat pyramid algorithm facilitates comprehensive examination. Static displacements at the connection point between the cable and the truss mast serve as the measured variables. Through systematic investigation, the paper evaluates the impact of damage size and location, external loading force, and cable tension force on the efficacy of the proposed approach. Utilizing data derived from Finite Element Method (FEM) computations for wavelet analysis the authors substantiate the findings with numerical examples, thus offering valuable insights into damage detection strategies for structural health monitoring and engineering applications.

Sudden cardiac arrest (SAC) is a leading cause of mortality. In recent years, though, many lives have been saved through the use of defibrillators by random bystanders. As a result, defibrillators have been popping up in various locations. In this work we propose a state mandate demanding the presence of a defibrillator at every pharmacy store and argue that it could greatly enhance and augment the impact of the defibrillator network. We support our claim via detailed calculations of the immediate (a defibrillator readily available) and partial (a defibrillator available at a reasonable distance) population coverage achievable by the implementation of our proposal, taking the Argolis area in Peloponnese Greece as a case study. Our findings indicate that, in addition to other benefits, the use of pharmacies to establish a defibrillator network could bring an eight-fold increase in the immediate population coverage of defibrillators and would provide immediate / partial access to a defibrillator to 18 / 24 incidents of SCA per year that would otherwise lead to death, potentially leading to the saving of numerous lives. Alternative scenaria are also discussed.

Cities are undergoing huge shifts in technology and operations in recent days, and `data science' is driving the change in the current age of the Fourth Industrial Revolution (Industry 4.0 or 4IR). Extracting insights or actionable knowledge from city data and building a corresponding data-driven model is the key to making a city system automated and intelligent. Data science is typically the study and analysis of actual happenings with historical data using a variety of scientific methodology, machine learning techniques, processes, and systems. In this paper, we concentrate on and explore ``Smart City Data Science", where city data collected from various sources like sensors and Internet-connected devices, is being mined for insights and hidden correlations to enhance decision-making processes and deliver better and more intelligent services to citizens. To achieve this goal, various machine learning analytical modeling can be employed to provide deeper knowledge about city data, which makes the computing process more actionable and intelligent in various real-world services of today's cities. Finally, we identify and highlight ten open research issues for future development and research in the context of data-driven smart cities. Overall, we aim to provide an insight into smart city data science conceptualization on a broad scale, which can be used as a reference guide for the researchers, professionals, as well as policy-makers of a country, particularly, from the technological point of view.

Objective. To test the hypothesis that a session of unilateral tSMS over the dominant primary motor cortex (M1) in healthy subjects produces a transient decrease in manual dexterity. Methods. A triple-blinded randomized control trial was conducted in 40 healthy participants who were allocated to real- or sham-tSMS group. Each participant underwent one session of tSMS and were assessed before, immediately after, 15 minutes, and 40 minutes after stimulation. Outcome measures were Finger Tapping Test (FTT), 5-seconds FTT, nine Hole Peg Test, and the hand grip assessment. Results: Significant differences were found between groups 15 minutes after stimulation in favor of the tSMS group in the FTT (2.2 ± 0.99; CI= .18-4.22; d= .84p=.034), and 5-second FTT (4.2 ± 1.98; CI= .199-8.2, d= .68; p=.04). In the intragroup analysis, a significantly lower number of taps 15 minutes after stimulation was observed in sham group (3.3 ± 1.01; CI= .47-6.13; d= .42; p=.015), but not in the real stimulation group. Conclusion: A unilateral session of tSMS in the M1 of the dominant hemisphere of healthy individuals does not reduce manual dexterity or grip strength. This technique could have benefits on the motor performance of the arm contralateral to the stimulated motor cortex

Data obtained by Direct Numerical Simulations (DNS) of pressure-driven turbulent channel flow are studied in the range 180 ≤ Reτ≤ 10,000. Reynolds number effects on the Mean Velocity Profile (MVP) and second order statistics are analyzed with a view of finding logarithmic behavior in the overlap region or even further from the wall, well in the boundary layer’s outer region. Values of Kármán constant for the MVPs and the Townsend-Perry constants for the streamwise and spanwise fluctuation variances are determined for the Reynolds numbers considered. A data-driven model of the MVP, proposed and validated for zero pressure gradient flow over a flat plate, is employed for pressure-driven channel flow by appropriately adjusting Coles’ strength of the wake function parameter, Π. There is excellent agreement between the analytic model predictions of MVP and the DNS-computed MVP as well as of the Reynolds shear stress profile. The skin friction coefficient Cf is calculated analytically. The agreement between the analytical model predictions and the DNS-based computed discrete values of Cf is excellent.

With the rapid development of space programs in various countries, the number of satellites in space is increasing, resulting in an increasingly complex space environment. Therefore, improving space object identification technology has become highly important. We proposes a method of applying deep learning to intelligent detection of space object. We utilize 49 authentic 3D satellite models including 16 scenarios to generate a dataset comprising 17,942 images, which contains over 500 actual satellite photos. Additionally, we acquired a substantial amount of annotated data using a semi-automatic labeling method, which resulted in significant labor cost savings, and obtained a total of 39,000 labels. We validate the feasibility of the dataset using YOLOv3 and YOLOv7 models. What's more, we optimize the YOLOv7 model by integrating deformable convolution RepPoint into the YOLOv7 backbone to obtain the YOLOv7-R model. Through training with these two models, experimental results show that YOLOv3 achieves an accuracy of 0.927, YOLOv7 reaches an accuracy of 0.964, and YOLOv7-R achieves the highest accuracy at 0.983. This provides an effective solution for intelligent space object detection.

The road traffic injuries risk factors such as driving offenses and average speed are concerns for health organizations to reduce the number of injuries. Without any comprehensive view of each road, one cannot decide about the effective policy. In this manner, the data-driven policy will help to improve and assess the decisions. The count data near the road of two airports is surveyed for investigating the time-varying speed zones. The descriptive statistics, ANOVA, and functional data analysis were used. The hourly data of traffic counts for four different locations at the entrance of the two airports, international and domestics, were collected for one the year 2018 to 2019.The hourly pattern of driving offenses for each road was assessed and the to and from airport roads had different peaks (<0.05). The hour, weekdays, type of airport, direction and their interactions were statistically significant (<0.05) for the chance of driving offenses. The speed average during the day was statistically different (<0.5) by the number of different types of vehicles. The traffic count data is a great resource for decision making in safe driving subjects such as driving offenses. With functional data analysis, we can analyze them to get the most of the characteristics of this data. The airports are public places with high traffic demand in all countries that yields the different pattern of traffic transportation, therefore we extract the factors that affect the driving offenses. Finally, we conclude that conducting a time-varying speed zone near the airports seems vital.

With increasing air and sea temperatures, the thermodynamic environments over the oceans become more favourable for the development of intense tropical cyclones (TCs) with rapid intensification (RI). In fact, the number of TCs undergoing RI is rising (Zhao, et al., 2018; Bhatia, et al., 2019; Song, et al., 2020; Hong & Wu, 2021; Liu, et al., 2022). RI over coastal sea areas before landfalling is particularly impactful and threatening to coastal lives and properties. There have been studies showing that offshore areas within 400 km of the coastline have experienced a significant increase in RI events with the count tripling from 1980 to 2020 (Li et al., 2023). The south China coastal region consists of highly densely populated cities especially the Pearl River Delta (PRD) region. Intense TCs maintaining its strength or RI of TCs close to the coastal region presents substantial forecasting challenges. This study investigates the effect of sea surface and subsurface temperature and salinity on the intensification of five TCs, namely Super Typhoons Hato in 2017 and Mangkhut in 2018, Typhoon Talim, Super Typhoon Saola and Severe Typhoon Koinu in 2023, which significantly affected the south China coastal region and triggered high TC warning signals in Hong Kong. The analysis utilized the Hong Kong Observatory (HKO) TC track and intensity data, along with the sea temperature and salinity profiles generated using the China Ocean ReAnalysis version 2 (CORA2) of the National Marine Data and Information Service (NMDIS) of China. While high sea surface temperature (SST) of 30°C or above, low surface sea surface salinity (SSS) of 34 psu or below, and strong salinity stratification of at least 0.8 psu per 100 m depth may offer useful hints for predicting RI, they are part of a broader set of contributing factors. This study represents the initial documentation of sub-surface salinity's impact on intense TCs over the South China Sea (SCS) in recent years and will encourage further research to refine forecasting RI of TCs before making landfall near PRD taking into account the effect of freshwater from the Pearl River.

Cloud computing refers to applications delivered as services over the Internet. Cloud systems employ policies that are inherently dynamic in nature and that depend on temporal conditions defined in terms of external events, such as the measurement of bandwidth, use of hosts, intrusion detection or specific time events. In this paper, we investigate an optimized resource management scheme named v-Mapper. The basic premise of v-Mapper is to exploit application-awareness concepts using software-defined networking (SDN) features. This paper makes three key contributions to the field: (1) We propose a virtual machine (VM) placement scheme that can effectively mitigate the VM placement issues for data-intensive applications; (2) We propose a validation scheme that will ensure that a service is entertained only if there are sufficient resources available for its execution and (3) We present a scheduling policy that aims to eliminate network load constraints. An evaluation was carried out with various benchmarks and demonstrated that v-Mapper shows improved performance over other state-of-the-art approaches in terms of average task completion time, service delay time and bandwidth utilization. Given the growing importance of supporting large-scale data processing and analysis in datacentres, the v-Mapper system has the potential to make a positive impact in improving datacentre performance in the future.

The integration of deep learning models into financial risk prediction and analysis has significantly transformed traditional approaches. While conventional quantitative methods often rely on simplistic metrics like maximum drawdown, the advent of deep learning necessitates a more nuanced evaluation, emphasizing the model's generalization ability, especially during market crises such as stock market crashes. This paper explores the critical aspects of evaluating deep learning models' risk control capabilities in finance, underscoring the importance of understanding both statistical metrics and generalization abilities, particularly in adverse market conditions. By examining deep learning models' performance in scenarios like stock market crashes and highlighting the significance of cross-validation techniques, this study aims to offer practitioners insights into constructing robust risk management systems. It advocates for a comprehensive approach integrating quantitative analysis with macroeconomic factors to enhance financial risk prediction and analysis in volatile markets. The experimentation reveals that different deep generative models excel in various aspects of financial time series analysis, with generative adversarial networks (GANs) demonstrating superior performance in predicting Value at Risk (VaR) and variational autoencoders (VAEs) excelling in return rate prediction. Moreover, integrating multiple models further enhances predictive performance, leveraging the strengths of each model to compensate for individual weaknesses. Overall, this paper underscores the potential and significance of deep generative models in financial time series analysis, offering a roadmap for improved risk management and decision-making in financial markets.

Accurate power curve modelling is essential to continuously evaluate the performance of a wind turbine (WT). In this work, we characterize the wind power curves using SCADA data acquired at a frequency of 5 minutes in a wind farm (WF) consisting of 5 WTs. Regarding the non-parametric methods, we select artificial neural networks (ANNs) to make curve estimations. Given that, we have the curves provided by the manufacturer of the WTs given by some very precisely measured pair of wind speed and power points. We can evaluate the difference between the manufacturer characterization and the ones estimated with the data provided by the SCADA system. Before the estimation, we propose a method of filtering the anomalies based on the characteristics provided by the manufacturer. We use three-quarters of the available data for curve estimation and one-quarter for the test. One WT suffered a break in the test part, so we can check how the test estimates reflect this problem in its wind-power curve compared to the estimations obtained in the WTs that worked adequately.

Deep learning has achieved remarkable success in diverse computer science applications, however, its use in other traditional engineering fields has emerged only recently. In this project, we solved several mechanics problems governed by differential equations, using physics informed neural networks (PINN). The PINN embeds the differential equations into the loss of the neural network using automatic differentiation. We present our developments in the context of solving two main classes of problems: data-driven solutions and data-driven discoveries, and we compare the results with either analytical solutions or numerical solutions using the finite element method. The remarkable achievements of the PINN model shown in this report suggest the bright prospect of the physics-informed surrogate models that are fully differentiable with respect to all input coordinates and free parameters. More broadly, this study shows that PINN provides an attractive alternative to solve traditional engineering problems.

This paper presents a methodology for predictive and prescriptive analytics of complex engineering systems. The methodology is based on a combination of physics-based and data-driven modeling using machine learning techniques. Combining these approaches results in a set of reliable, fast, and continuously updating models for prescriptive analytics. The methodology is demonstrated with a case study of a jet-engine power plant preventive maintenance and diagnostics of its flame tube.

Mental health issues can have significant impacts on individuals and communities and hence on social sustainability. There are several challenges facing mental health treatment, however, more important is to remove the root causes of mental illnesses because doing so can help prevent mental health problems from occurring or recurring. This requires a holistic approach to understanding mental health issues that are missing from the existing research. Mental health should be understood in the context of social and environmental factors. More research and awareness are needed, as well as interventions to address root causes. The effectiveness and risks of medications should also be studied. This paper proposes a big data and machine learning-based approach for the automatic discovery of parameters related to mental health from Twitter data. The parameters are discovered from three different perspectives, Drugs & Treatments, Causes & Effects, and Drug Abuse. We used Twitter to gather 1,048,575 tweets in Arabic about psychological health in Saudi Arabia. We built a big data machine learning software tool for this work. A total of 52 parameters were discovered for all three perspectives. We defined 6 macro-parameters (Diseases & Disorders, Individual Factors, Social & Economic Factors, Treatment Options, Treatment Limitations, and Drug Abuse) to aggregate related parameters. We provide a comprehensive account of mental health, causes, medicines and treatments, mental health and drug effects, and drug abuse, as seen on Twitter, discussed by the public and health professionals. Moreover, we identify their associations with different drugs. The work will open new directions for social media-based identification of drug use and abuse for mental health, as well as other micro and macro factors related to mental health. The methodology can be extended to other diseases and provides a potential for discovering evidence for forensics toxicology from social and digital media.

The Solvency II regulatory framework specifies procedures and parameters for determining solvency capital requirements (SCRs) for insurance companies. The proposed standard SCR calculations involve two steps. The Value–at–Risk (VaR) of each risk driver is measured and, in a second step, all components are aggregated to the company’s overall SCR, using the Standard Formula. This formula has two inputs: the VaRs of the individual risk drivers and their correlations. The appropriate calibration of these input parameters has been the purpose of various Quantitative Impact Studies that have been conducted during recent years. This paper demonstrates that the parameter calibration for the equity–risk module—overall, with about 25%, the most significant risk component—is seriously flawed, giving rise to spurious and highly erratic parameter values. As a consequence, an implementation of the Standard Formula with the currently proposed calibration settings for equity–risk is likely to produce inaccurate, biased and, over time, highly erratic capital requirements.

Intrinsically Disordered Proteins (IDPs) play crucial roles in signal transduction, cell differentiation, and transcriptional regulation. Many disrupted genes associated with mental disorders are identified as IDPs, and emerging evidence suggests the functional role of IDPs in neuropsychiatric disorders. However, few studies comprehensively explore the functional association between protein disorder properties and different mental diseases. To address this gap, we collected disrupted gene sets for seven mental diseases (MDD, SCZ, BP, ID, AD, ADHD, ASD) and a control gene set from normal brains using DisGeNET and GeneCards databases. The state-of-the-art predictor IUPred2A was then utilized to calculate the disorder properties , followed by a thorough comparison between the disordered proteins in mental diseases and healthy controls. Functional enrichment analysis and protein-protein interaction networks were conducted to investigate the IDPs’ functional roles in psychiatric diseases. Additionally, we demonstrated the role of IDPs in protein binding formations through a case study of alpha-synuclein using protein docking. Our findings reveal that differentially expressed proteins in mental disorders, especially in ASD and ADHD, exhibit more IDPs than those in healthy controls. IDPs in psychiatric disorders are significantly enriched in neurodevelopmental pathways and play an important role in in gene expression regulation. Our results indicate distinct functional patterns of disorder proteins among mental diseases and healthy controls. When comparing the IDPs between ASD and ADHD, we observed that IDPs in ADHD are more likely linked to the synaptic signaling and regulation, while IDPs in ASD are more tendentiously related to diverse and complex biological processes. Our work offers valuable insights into the important functions of IDPs in psychiatric disorders, enhancing our understanding of the molecular mechanisms involved in psychiatric disorders.