Yttria stabilized zirconia (Y-TZP) ceramics with drastically reduced yttria content have been introduced by different manufacturers aiming at improving the damage tolerance of ceramic components. In this study an alumina doped 1.5Y-TZP was axially pressed, pressureless sintered in air at 1250–1400 °C for 2 h and characterized with respect to mechanical properties, microstructure and phase composition. The material exhibits a combination of high strength of 1000 MPa and a high toughness of 8.5–10 MPa√m. The measured fracture toughness is, however, extremely depending on measurement protocol. Direct crack length measurements overestimate toughness due to trapping effects. The initially purely tetragonal material has a high transformability of > 80 %, the transformation behavior is predominantly dilatoric, measured R-curve related toughness increments are in good agreement with transformation toughness increments derived from XRD data.

Yttria stabilized zirconia materials are frequently used in mechanical engineering and biomedical applications. Demanding loading conditions require materials combining a high level of strength and fracture toughness. A ready to press alumina doped 2 mol% yttria stabilized zirconia powder was shaped by axial pressing and sintering in air at 1250 - 1500 °C for 2 h. The best combination of strength and toughness value of 7.8 MPa√m. Materials sintered in the middle of the chosen temperature range combine fully density, high transformability and small grain size. Toughness measurements by direct crack length measurements delivered unrealistically high fracture toughness values.

The reservoir water level fluctuation zones (RWLFZs) and the natural riparian zones (NRZs) are two riparian ecosystems with the dramatically opposite hydrological rhythms which notably influence the plant guilds. However, little is known about the discrepancy of functional traits and niche characteristics of plant guilds in the RWLFZ and NRZ under different flooding rhythms. Here the RWLFZs (degraded riparian zones) and NRZs were chosen in the Xiangxi River Basin of the Three Gorges Reservoir (TGR) to investigate the variation in plant community structure, the spatial patterns of diversity, key functional traits and niche characteristics of dominant plant populations. The results showed that a total of 78 vascular plant species were identified in the riparian zones of Xiangxi River Basin. Most of the dominant species were annual herbs in the two riparian ecosystems and the percentage of annual dominant species increased from 65.79% in the NRZ to 67.34% in the RWLFZ. Compared with the NRZ, the specific leaf area, vegetation coverage and the aboveground biomass in the RWLFZ significantly increased by 74%, 27% and 19.6% respectively, while the water use efficiency of the RWLFZ decreased by 59.6% and there was no significant difference in the net photosynthetic rate between them, which showed that annuals in the RWLFZ adopt the R adaptation strategy with fast-growing, short lifespan and quickly acquiring and investing resources by altering leaf morphology such as expanding leaf area. The Simpson dominance index of RWLFZ was significantly higher than that of NRZ. Thus counter-seasonally hydrological alterations had the significant effects on functional traits of dominant species in the RWFLZ. Moreover, the highly adaptable and widely distributed species with larger niche breadths and high important values usually had a higher niche overlap value in the RWLFZ than in the NRZ, which showed that the competition in the plant community after experiencing anti-seasonal flooding was much more intraspecific than interspecific and would facilitate the expansion of species niches. And the distribution of the plant community was mainly driven by elevation (flooding depth), flooding duration and TK in the WLFZs. Our findings imply that the species with large niche breadths and high important values should be prioritized in ecological restoration efforts in the newly formed hydro-fluctuation zone of the TGR.

This paper focus on the modeling and time-domain analyzing method of piecewise-smooth fractional-order circuit systems. Firstly, an analytical framework is constructed based on a generalized piecewise-smooth two-port impedance network model, which takes the topological characteristics of Dickson type switched-capacitor converters (SCCs) as examples, and considers the fractional-order characteristics of class-2 X7R ceramic capacitors, which are widely used in SCCs. Secondly, the time-domain analyzing method for such a piecewise-smooth fractional-order circuit system is developed, numerical solutions are obtained, and the influence of the fractional-order capacitor on the power conversion efficiency of the system are revealed. Finally, in order to validate the analysis, both numerical simulation and experiments are provided in the work, the results of which confirm that, the proposed fractional-order analytical framework can capture the power loss mechanism of piecewise-smooth fractional-order circuit systems more effectively than the traditional integer-order based approach, thus benefiting the design of circuit systems.

In order to study the adsorption process and adsorption characteristics of shale oil at the macro scale, the isothermal adsorption experiments of illite and kerogen on heptadecane (oil phase) solution were carried out by infrared spectrophotometry and gas chromatography-mass spectrometry. The reaction mechanism of alkane solution concentration and temperature in the adsorption process was investigated. The adsorption characteristics of heptadecane on the surface and pores of illite and kerogen were elucidated by adsorption isotherm model and adsorption thermodynamic model. The results show that: The concentration of alkane solution contributes to the adsorption of illite and kerogen. As the concentration of the solution continues to increase, the adsorption rate gradually slows down. However, the temperature hardly affects the adsorption rate. At 25℃, 50℃ and 60℃, the adsorption process of illite on alkane solution is more consistent with Langmuir model and Freundlich model, respectively. The difference is that Langmuir model is suitable for describing the whole adsorption process of kerogen on alkane solution. 3) The adsorption process of illite and kerogen to heptadecane solution is an endothermic reaction. Heating helps to accelerate the migration rate of alkanes, which is conducive to the adsorption reaction. The research results clarify the adsorption characteristics of shale oil heavy components from the macro level, and fill the research gap in the application of solid-liquid isothermal adsorption physical experiments to the adsorption and occurrence of shale oil.

The aim of this study was to investigate the physicochemical characterization and biological activities of chitosan (CH) based composite films with the incorporation of chestnut flower essential oil (CFEO). The composite films were prepared by casting method and characterized in terms of structural, morphological and mechanical properties via FT-IR, XRD, UV, SEM and TGA. The results proved the significantly increased water vapor permeability (WVP), heat resistance, antibacterial and antioxidant capabilities of CH-CFEO films. The incorporation of CH and CFEO enhanced the UV blocking, which made the film shield almost all UV light. Films with the tensile strength of 6.37 ± 0.41 MPa and elongation at break of 22.57 ± 0.35% were got with 6 mg mL-1 CFEO. Subsequently, the fruit preservation experiments also confirmed that the composite films could effectively extend the shelf life of bananas through their excellent water vapor and oxygen barrier. These desirable performances enable our newly developed composite films to be a remarkable packaging material to solve the fresh fruit preservation dilemma.

Sepsis, characterized by a dysregulated systemic inflammatory response to infection, remains a significant global health burden, despite substantial advancements in its treatment. An understanding of the underlying mechanisms driving sepsis is crucial for the development of targeted therapeutic strategies. Silent information regulator 1 (SIRT1), a member of the class III histone deacetylases, plays a pivotal role in regulating gene expression by catalyzing the deacetylation of lysine residues on non-histone and histone proteins. With the advancement of sepsis research, SIRT1 has been shown to exert significant anti-inflammatory, anti-oxidative, anti-apoptotic, and metabolic regulatory effects, positioning it as a potential therapeutic target for sepsis. This article reviews the latest progress on research into the signaling pathways modulated by SIRT1 in sepsis and its associated regulatory mechanisms to further elucidate the pathogenesis of sepsis and assist in guiding clinical treatment.

Sepsis-induced cardiomyopathy (SICM) may be defined as a non-ischemic cardiac dysfunction associated with sepsis. SICM is characterized by a decrease in left ventricular contractility, ultimately associated with left ventricular dilation, with or without right ventricular dysfunction. Echocardiography stands as the current gold standard in diagnosis of SICM. Left ventricular ejection fraction (LVEF) is the most frequently utilized parameter for evaluating left ventricular systolic function, but some traditional parameters, including LVEF, are dependent on cardiac preload and afterload, limiting their clinical application. Advanced echocardiography techniques, such as speckle-tracking analysis, have the potential to diagnose and evaluate myocardial dysfunction even in the early phases of sepsis, facilitating risk stratification for proactive personalized treatment of patients. This article reviews the progress in the application of various echocardiographic parameters in SICM.

Astragalus plants belong to the legume family and have obvious rhizosphere effect. The northwestern area of Yunnan China is the main distribution region of Astragalus plants with high application value, but low recognition and resource reserves. The aim of this research is to explore the species diversity of cultivable rhizosphere fungi derived from A. acaulis, A. forrestii, and A. ernestii growing in special high-cold environment of northwest Yunnan, and discover anti-infective components from these fungi. A total of 93 fungal strains belonging to 38 species in 18 genera were isolated and identified. Antibacterial and antimalarial screening yielded 10 target strains. Among them, the ethyl acetate crude extract of the fungus Aspergillus calidoustus AA12 from A. acaulis fermentation substance showed a broad antibacterial spectrum and the best antimalarial activity. Further chemical investigation led to the first discovery of seven compounds from the species of A. calidoustus, including a sesterterpine 6-epi-ophiobolin G (1), two sesquiterpenes penicisochroman A (2), pergillin (3) and 7-methyl-2-(1-methylethylethlidene)-furo[3,2-H]isoquinoline-3-one (4), and three polyketides trypacidin (5), 1,2-seco-trypacidin (6) and questin (7). Compound 1 exhibited moderate to strong antibacterial activity against six Gram-positive pathogens with the minimum inhibitory concentration (MIC) ranging from 25 to 6.25 μg/mL, and prominent inhibitory effect on the biofilm of Streptococcus agalactiae at MIC value of 3.125 μg/mL. This compound also displayed potent antimalarial activity against Plasmodium falciparum strains 3D7 and chloroquine-resistant Dd2 at the half maximal inhibitory concentration (IC50) values of 3.319 and 4.340 µmol/L at 72 h, respectively. This study contributed to our understanding of the cultivable rhizosphere fungi Astragalus-derived in special high-cold environment and further increased the library of fungi available for natural anti-infectious products screening.

This paper proposes a new cascaded three-phase multilevel inverter based on a cascaded submultilevel and single-phase H-bridge structure. The voltage source of the traditional single-phase H-bridge is replaced with the proposed cascaded submultilevel. Cascading two basic units forms the submultilevel unit. The basic and submultilevel units generate positive voltage only hence the need for an H-bridge to generate both polarities of load voltage. Five algorithms of source voltage are proposed and the optimal algorithm selected to generate the peak load voltage and output levels. The proposed three-phase cascaded multilevel inverter generates 31-level of load voltage. The per-phase component distribution of the proffered inverter are twelve power switches, four dc sources and twelve driver circuits accordingly. Principal merits of the proposed 31-level inverter are high quality load waveforms, production of high levels of load voltage utilizing reduced component quantity, simple cascaded layout, decreased inverter area, minimal inverter cost, minimum inverter losses and utilizing lower rated switches. Also, the proposed topology is highly suited for employment in PV-DVR and other power systems. To validate these advantages of the proposed multilevel inverter, contrastive analysis of the proposed inverter and existing topologies are studied. Finally, the functionality of the proposed inverter is substantiated by simulation in PSCAD/ EMTDC software.

Keywords: Antibacterial activity, Antioxidant activity, Bioactive compounds, Elementary analysis, Nutritional and phytochemical composition, Seaweed.

Crop production in Afghanistan suffers from limited phosphorus (P) availability, which severely hinders national agriculture sustainability. This present study hypothesized that deep fertilizer placement could significantly enhance uptake of immobile P and thus tissue P accumulation and crop yield. A two-year pot experiment growing two maize (Zea mays) hybrid cultivars (Xida-789 and Xida-211) was therefore conducted to test these hypotheses under three contrasting fertilizer placement methods (broadcast, side band, and deep band). In doing so, P concentrations in both maize tissues and soils were compared at 45, 60, and 115 days after sowing (DAS) under nine combinations of nitrogen (N) and P fertilizer rates (kg ha-1: N112P45, N112P60, N112P75, N150P45, N150P60, N150P75, N187P45, N187P60, N187P75). Results have shown that deep band placement significantly increased P uptake efficiency, leading to greater P concentration and accumulation in maize tissues compared to other two fertilization methods. This improved P uptake was attributed to several factors associated with deep placement, including reduced P fixation, enhanced root access to P, and moisture availability for P uptake. Additionally, deep band placement combined with higher N application rates (N187 and N150) further enhanced plant P uptake by promoting P availability and utilization mechanisms. Deep band placement also resulted in significantly higher total soil P, Olsen-P, and P use efficiency than broadcast and side band methods, indicating a more efficient P fertilization strategy for maize that can improve growth and yield. This present study also found positive correlations between P concentration in plant organs and soil Olsen-P, highlighting the importance of adequate soil P levels for optimal plant growth. Overall, our results have showed that deep band fertilizer placement emerged as a superior strategy for enhancing P uptake efficiency, utilization, and maize productivity compared to broadcast and side band placement. This approach can potentially optimize P fertilizer utilization, improve maize growth and yield, while minimizing environmental P losses associated with broadcast applications.

The 32CA reactions of a series of pairs of bent three-atom-components (B-TACs) and linear TACs (L-TACs) towards electrophilic dicyanoethylene (DCE) have been studied within the Molecular Electron Density Theory in order to understand their different reactivity. ELF analysis indicates that while pseudodiradical B-TACs change their electronic structure to pseudoradical or carbenoid L-TACs upon dehydrogenation, zwitterionic B-TACs experience no remarkable change. Analysis of the CDFT indices indicates that five of the nine studied TACs have a strong nucleophilic character, thus participating in polar reactions towards electrophilic ethylenes. The activation energies of the 32CA reactions of the nine TACs towards electrophilic DCE range from 0.6 to 22.0 kcal·mol-1, which are by between 2.0 and 10.1 kcal·mol-1 lower than those involved in the non-polar 32CA reactions with ethylene. In general, B-TACs are more reactive than their L-TAC counterparts. A change of the regioselectivity is found in these polar 32CA reactions; in general, while B-TACs are meta regioselective, L-TACs are ortho regioselective. Analysis of the geometrical parameters indicates that at all TSs, the formation of the single bond involving the most electrophilic C4 carbon of DCE is more advanced than that involving the C5 one. A change of the asynchronicity in the reactions involving B-TACs and L-TACs is also found.

In large-capacity energy storage systems, instructions are decomposed typically using an equalized power distribution strategy, where clusters/modules operate at the same power and durations. When dispatching shifts from stable single conditions to intricate coupled conditions, this distribution strategy inevitably results in increased inconsistency and hastened system aging. This paper presents a novel differentiated power distribution strategy comprising three control variables: the rotation status, the operating boundaries for both Depth of Discharge (DOD) and C-rates (C) within a control period. The proposed strategy integrates an aging cost prediction model developed to express the mapping relationship between these control variables and aging costs. Additionally, it incorporates the multi-colony particle swarm optimization (Mc-PSO) algorithm into the optimization model to minimize aging costs. The aging cost prediction model consists of three functions: predicting health features (HFs) based on the cumulative charge/discharge throughput quantity and operating boundaries, characterizing HFs as comprehensive scores, and calculating aging costs using both comprehensive scores and residual equipment value. Further, we elaborated on the engineering application process for the proposed control strategy. In the simulation scenarios, this strategy prolonged the service life by 14.62%, reduced the overall aging cost by 6.61%, and improved module consistency by 21.98%, compared with the traditional equalized distribution strategy. In summary, the proposed strategy proves effective in elongating service life, reducing overall aging costs, and increasing the benefit of energy storage systems in particular application scenarios.

Using numerical simulation method, combined with the pre-branch material characteristics of the measurement results, based on the LS-DYNA software to simulate the branch crushing process, the analysis found that not only the existence of the cutter cutting in the branch destruction process, there is also the cutting of the opposing surface of the bending fracture, with the increase in the speed of the knife rollers, the cutter cutting resistance increases, the cutting resistance reaches 2690 N when the cutter at 2500 r/min, the cutter cutting resistance is the smallest in the cutting simulation at the blade angle of 55°, the blade angle is more suitable for the cutting of the branch. In the cutting simulation under different cutting edge angles, the cutting resistance of the tool is the smallest when the edge angle is 55°, which is 1860 N. This edge angle is more suitable for branch crushing and cutting. Using Fluent software to analyse the airflow characteristics of the crushing device, it was found that with the increase of the knife roller speed, the inlet flow and negative pressure of the crushing chamber are increasing, the speed of 2500 r/min, the inlet flow and negative pressure were 1.92 kg/s and 37.16 Pa, which will be conducive to the feeding of branches, but the speed is too high and it will also lead to the enhancement of the vortex of part of the area in the crushing device, which will affect the feeding of branches and the throwing of the crushed material. affect the feeding of branches and the throwing out of crushed materials, and finally determined the speed range of the crushing knife roller is 1800 ~ 2220 r/min. Based on ANSYS/Model module modal analysis of the crushing knife roller, the knife roller of the first six orders of the intrinsic frequency and vibration pattern, crushing knife roller of the lowest order of the modal intrinsic frequency of 137.42 Hz, much larger than the crushing knife roller operating frequency of 37 Hz, the machine will not resonate during operation.

Glial cells provide physical and chemical support and protection for neurons. Secreted neurotrophic factors, scaffolds and vesicles regulate in addition to normal homeostasis, repair following neural tissue injury or degeneration. We previously demonstrated that human CNS glia have revascularization capacity by inducing endothelial cell sprouting and microchanneling driven by glial cell secreted components. The clinical potential of using secreted factors and vesicles generated by glial cells in conditioned media was shown by their re-normalization of pathological blood vessels and 3D tissue wound healing and remodeling capacity. To identify secreted components of glial cells and how CNS and PNS glial cells differentially regulate neural tissue homeostasis, disease and injury response, we developed a novel culture method for various types of glial cells that allow for isolating and characterizing secreted glial components, free of animal factors and contaminants normally associated with serum-based culture conditions. Our culture method will enable to identify secreted components using ultrasensitive RNA, glycoconjugate and protein analysis technologies. The characterization of glial secreted factors involved microchanneling may help in development of new clinical therapies for glial and neural cells or axons to migrate and reform connections.

In the context of global urbanization and climatic change, the frequency of various uncertainties and disturbances faced by urban system is increasing, and enhancing urban resilience has become one of the vital components of sustainable development of modern cities. At the same time, urban resilience has become a hot topic in interdisciplinary research such as economics, ecology, and geography. This paper constructs urban resilience evaluation indicator system based on four dimensions—economy, ecology, society, and infrastructure. The evaluation indicator is used to measure the resilience levels of Yichang-Jingzhou-Jingmen-Enshi (YJJE) urban agglomeration in China from 2010 to 2023. Using the entropy weight method, the Getis-Ord Gi* model, and the robustness testing, this paper analyzes the spatiotemporal evolution characteristics of urban resilience in YJJE urban agglomeration. Then, the factor contribution model is used to explore the influencing factors of urban resilience. Finally, the CA-Markov model is used to predict urban resilience in 2030. The results are as follows: From 2010 to 2023, the urban resilience values of all prefecture-level and county-level cities in YJJE urban agglomeration showed an upward trend, and it indicated that the resilience of urban system is improving. Meanwhile, the urban resilience of YJJE urban agglomeration increased with an average annual growth rate of 3.25%. Furthermore, the urban resilience exhibited a significant spatially heterogeneity distribution, with Xiling, Wujiagang, Xiaoting, Yidu, Zhijiang, Dianjun, Dangyang, Yuan’an, Yiling, Duodao being the high-value agglomerations of urban resilience, and Hefeng, Jianli, Shishou, Wufeng being the low-value agglomerations of urban resilience. Then, we identified critical driving factors of urban resilience in YJJE urban agglomeration. Finally, the urban resilience of all cities within YJJE urban agglomeration will reach the medium level or higher than medium level in 2030. Xiling, Wujiagang, Xiaoting, Zhijiang, Dianjun, Dangyang, Yuan’an will remain hot spots of urban resilience, while Jianli will remain cold spots of urban resilience in the future. This study can provide the scientific reference and policy recommendation for the government to build resilient cities and improve sustainable urban development.

Let Vn(d) denote the least number such that every collection of nd-cubes with total volume 1 in d-dimensional (Euclidean) space can be packed parallelly into some d-box of volume Vn(d). We show that V3(d)=r1−dd if d≥11 and V3(d)=1r+1rd+1r−rd+1 if 2≤d≤10, where r is the only solution of the equation 2(d−1)kd+dkd−1=1 on 22,1 and (k+1)d(1−k)d−1dk2+d+k−1=kddkd+1+dkd+kd+1 on 22,1, respectively. The maximum volume is achieved by hypercubes with edges x, y, z such that x=2rd+1−1/d, y=z=rx if d≥11, and x=rd+(1r−r)d+1−1/d, y=rx, z=(1r−r)x if 2≤d≤10. We also proved that only for dimensions less than 11 there are two different maximum packings, and for all dimensions greater than 10 the maximum packing has the two smallest cubes the same.

Assessing the quality of corn seeds necessitates evaluating their content of water, fat, protein, and starch. This study integrates hyperspectral imaging technology with chemometric analysis techniques to achieve non-invasive and rapid detection of multiple key components in corn seeds. Hyperspectral images of the embryo surface of maize seeds were collected within the wavelength range of 1100~2498nm. Subsequently, image segmentation techniques were applied to extract the germ structure of the corn seeds as the region of interest. Seven spectral data preprocessing algorithms were employed, and the Detrending Transformation (DT) algorithm was identified as the optimal preprocessing method through comparative analysis using the Partial Least Squares Regression (PLSR) model. To reduce spectral redundancy and streamline the prediction model, three algorithms were employed for characteristic wavelength extraction: Successive Projections Algorithm (SPA), Competitive Adaptive Reweighted Sampling (CARS), and Uninformative Variable Elimination (UVE). Using both the original spectra and the extracted characteristic wavelengths, four content detection models were constructed: PLSR, Back Propagation Neural Network (BPNN), Radial Basis Function Neural Network (RBFNN), and Least Squares Support Vector Machine (LSSVM). The experimental results demonstrate that the DT-CARS-LSSVM model exhibits exceptional accuracy and stability in predicting these four key components, with determination coefficients of 0.9877, 0.9344, 0.9827, and 0.9592, respectively. This study not only provides a scientific basis for evaluating the quality of corn seeds but also opens up new avenues for the development of non-invasive detection technology in related fields.

Clinical and laboratory diagnostics are particularly important in monitoring the internal homeostasis of the body in high-yielding animals, especially in dairy cows, whose metabolism is under constant pressure to obtain high parameters of milk production and reproduction. Knowledge of laboratory test results and relationships based on significant correlations between various milk and blood parameters may be very useful in veterinary diagnostics and helpful in cattle practice in order to protect animal health and the quality of milk production. The aim of the study was to analyze the correlation between selected hematological biomarkers such as white blood corpuscles (WBC), red blood corpuscles (RBC), hemoglobin concentration (HGB), hematocrit (HCT), platelets (PLT), erythrocyte mean corpuscular volume (MCV), mean corpuscular hemoglobin content (MHC), mean corpuscular hemoglobin concentration (MCHC) and selected quantitative-qualitative parameters of cow’s milk such as current milk production, somatic cells count (SCC), colony of bacteria forming units (CFU), milk fat (MF), milk protein (MP), milk lactose (ML), milk solids (S), solids non-fat in milk (SNF), daily milk production. Samples were collected three times at daily intervals from 11 clinically healthy late-lactation dairy cows obtaining 33 sets of test results. This repeated study of cows allowed for obtaining a homogeneous group in order to determine statistical correlations between selected blood and milk parameters. Many significant correlations were found between the examined parameters. In cows, significant positive correlations were recorded between milk production and HGB, HCT, MCV or MHC. Significant negative correlations were also found between SCC and HGB, SCC and HCT, SNF and MCV, SNF and MHC, and between MF and RBC.

Heat pumps are increasingly becoming a key solution in the quest for decarbonization, offering a significant advantage over traditional boilers due to their superior energy efficiency. Not only can heat pumps provide both heating and cooling, but they also achieve thermal efficiencies exceeding 500%, which can seem to defy conventional expectations. The outdoor unit of a heat pump consists of about twenty main components, one of which is a complex network of copper pipes and sheets welded to valves, connectors, and other fittings. This set involves over thirty welded joints, highlighting a significant opportunity for reducing manufacturing time through process optimization. Copper is a critical material extensively used in various applications due to its excellent thermal and electrical conductivity. However, these very properties make welding copper particularly challenging, especially when aiming to automate and streamline industrial processes. Traditionally, connecting copper pipes and fittings is done through brazing, yet, alternative methods such as LASER welding, electron beam welding, resistance welding, friction welding, and ultrasonic welding also exist. This study focuses on the ultrasonic welding of copper, aiming to identify the optimal parameters that maximize the mechanical strength of overlapping joints and ensure effective tube sealing. Experimental results showed that for copper sheets, the best outcomes were achieved with a welding time of 3 s and a pressure of 6 bar. For tube sealing, the optimal conditions were a welding time of 3 s and a pressure of 4 bar. For both scenarios, the same variables were used, retention time of 0.62 s, initial pressure of 2 bar, retention pressure of 2 bar and sonotrode rising pressure of 3 bar. The analysis reveals that ultrasonic welding of copper can achieve both robust mechanical strength and reliable sealing, making it a promising technique for industrial applications.

Additive manufacturing processes offer various options to fabricate metal parts, which show numerous ecological and technological advantages compared to formative and subtractive manufacturing methods. Due to quick availability and high accuracy, they are particularly suitable to produce complex prototypes. Metal fused deposition modeling is a relatively new material extrusion additive manufacturing technique based on the widely used fused filament deposition process. This study focuses on the Inconel 625 metal filament from Markforged Inc., it consists of a mixture of metal powder and a binder system, the latter being removed during washing and sintering. In this article, the mechanical properties of printed and sintered Inconel were investigated using tensile testing specimens with three different infill patterns, solid, triangular, and gyroid, printed in flatwise and upright direction. In addition, investigations into the dimensional accuracy of the printed specimens and the sintering shrinkage were carried out. The results showed that neither the dimensional accuracy nor the sintering shrinkage was significantly influenced by the printing orientation. In the context of lightweight engineering, the structures proofed beneficial especially within the elastic region. Generally, triangular infill patterns resulted in higher stiffness, while gyroids led to more ductile specimens. A mass-related evaluation of tensile testing elucidates that with aid of the infill structures weight savings of 40 % resulted in mechanical performance decreased by only 20 % on average.

Proton Exchange Membrane Fuel Cell (PEMFC) is a fast-developing battery technology, and the key to its reliability and lifespan improvement lies in the accurate assessment of durability. However, the degradation mechanism of PEMFC is hard to determine and its internal parameters are highly coupled. Thus, the development of the more accurate life prediction model that meets the actual scenarios is urgent to investigate. To solve this problem, a multi-feature fusion life prediction method based on Temporal Convolutional Network-Gated Recurrent Unit (TCN-GRU) is proposed. A TCN algorithm is used as the prediction base model, and two GRU modules are included to the model to strengthen the model expression ability and improve its predictive accuracy. Two widely recognized datasets and two operating conditions are utilized for model training and prediction, respectively. Comparisons are made with single-feature parameter models in terms of Root Mean Square Error (RMSE) and Determination Coefficient (R2). The results show that the prediction accuracy of the TCN-GRU multi-feature fusion model is higher than that of the single-feature models in terms of stability and anti-interference under both operating conditions. Furthermore, with the increase of input feature parameters, the TCN-GRU model is closer to the real value, which proves once again that the proposed model can meet the accuracy requirements of the life prediction of PEMFC.

Carotid atherosclerotic lesions are a major cause of cerebrovascular disease (CVD). Identification and quantification of carotid plaques are important for categorizing the vulnerability of plaques for rupture and assessing the impact of treatments. The irregularity of plaque surface is associated with previous plaque rupture and plays an important role in the risk of stroke. Thus, the aim of this study is to develop and validate novel vulnerability biomarkers from three-dimensional ultrasound (3DUS) images by analyzing the surface morphological characterization of carotid plaque using fractal geometry features. 3D box-counting and 3D blanket are the two types of 3D fractal dimension that were employed to describe the smoothness of plaques. This fractal dimension analysis tool was used to evaluate the effect of atorvastatin using 3DUS carotid images, which were acquired from 6 patients treated with atorvastatin with 80 mg daily and 5 patients with placebo. The Student's T Test results showed that those two fractal features were effective for detecting the statin-related changes in carotid atherosclerosis with p<0.0068 and p<0.015 respectively, suggesting that 3D fractal dimension measurements can be used effectively to analyze the surface characteristics of carotid plaques, especially for evaluating the impact of the treatment.

The discrete element method (DEM) coupled with computational dynamics (CFD) has been considered one of the most sensitive ways of studying fluidized beds. This paper presents gas-solid fluidized bed simulations by use of CFD-DEM. The two-phase interaction is calculated in a way of decoupling. Within the effective neighborhood of the particles, the kernel approximation method is used to calculate the local porosity, thereby calculating the drag force on the particles. At the grid scale, the momentum exchange coefficient is calculated using a two fluid model based method, thereby calculating the source term of the phase interaction in the fluid control equation. The simulated form, size and motion process of the big bubble are all consistent with experimental observations. The simulated solid volume fraction and relative pressure averaged in a horizontal plane at 45 mm above the bottom are in reasonable agreement with the experimental data. The fluctuation of the simulated bed height over time is similar to the experimental measurement results. The reproduction of these qualitative and quantitative results indicates that the proposed method effectively improves simulation performance and accuracy.

The paper provides and comments on the results of studies of the effect of sandstone-based abrasives and quartz sand alone on the wear of martensitic surfaces of wear-resistant steels. The wear process was examined on a ring-on-ring test rig seeking to determine the mass decrement parameter which characterised wear. The tests were conducted for three sandstone varieties: Carboniferous, Permian, and Cretaceous, and they made it possible to determine that the most intense process of deterioration of wear-resistant steels took place in the presence of quartz sand grain, while less intense wear was observed in the case of sandstone-based abrasives. The mass decrement values established in the presence of the sandstones in question did not differ significantly between individual sandstone varieties. Based on a surface damage analysis, the basic damage mechanism was found to be micro-scratching, however, with regard to the sandstones examined, it was also determined that individual grains could be pressed into surface irregularities, as well as that films of soft hematite cement developed in the Permian sandstone and that inclusions of carbonaceous matter were formed in the Carboniferous sandstone. With reference to the wear process observations, a wear model was described for the surface of the steels examined in the presence of sandstone-based abrasives.

Research into lightweight structural concrete using volcanic tuff is of great importance to the construction industry. These materials have excellent thermal insulation properties, which helps improve the energy efficiency of buildings. A three-factor experimental design was used to build the statistical model. The test methods used were methods for determining the crushability of volcanic tuff, determining the average density, compressive strength and thermal conductivity of lightweight structural concrete. The influence of basalt fiber on the properties of lightweight structural concrete has been determined. The optimal compositions of lightweight structural concrete using tuff have been selected. The compressive strength of lightweight structural concrete reached 32.0 MPa. The average density range is 1754.6-2114.0 kg/m³. Good thermal conductivity values ​​were obtained in the range of 0.653-0.818 W/m·K. The article obtained the optimal compositions of lightweight structural concrete using volcanic tuff as a filler.

This study extends the CGAN-based MODIS cloud vertical-profile (64×64-scene, about 70km width×15km height) retrieval technique developed by Leinonen et al. (2019) [1] to construct seamless 3D cloud fields for the MODIS granules [2]. Firstly, the accuracy and spatial continuity of the Leinonen et al. [1] retrievals are statistically evaluated. Then, according to the characteristics of the retrieval error, a spatially overlapping-scene ensemble generation method and a bi-directional Ensemble Binning Probability Fusion (CGAN-BEBPF) technique are developed, which improves the CGAN retrieval accuracy and support to construct seamless 3D clouds. The CGAN-BEBPF technique involves three steps: cloud masking, intensity scaling, and optimal value selection. It ensures adequate coverage of the low reflectivity areas while preserving the high reflectivity cloud cores. The technique is applied to retrieve the 3D cloud fields of Typhoon Chaba and a multi-cell convective system. The cloud structures of the CGAN-BEBPF results are highly consistent with the ground-based radar observations. It can retrieve weak clouds at the top levels of convective storms and hurricanes that were missed by ground-based radars and fill the gaps of the ground-based radar lower-level PPI scan. Overall, CGAN-BEBPF can be automated to retrieve the rich informative 3D structures of typhoons and severe convective systems over the oceans along the MODIS swath, which certainly presents great value for improving maritime and near-shore typhoons and convection prediction and other cloud-sensitive applications.

Most research on colostrum quality and colostrum management focuses on maternal IgG transfer to the newborn calf. However, in addition to being a source of antibodies, colostrum has other components that influence passive immune transfer, nutrition, gut maturation, and thermoregulation. In this review, the constituents in the bovine colostrum, as well as their variation, are explored and it is discussed the biological role of colostrum on the newborn calf. Protein is the nutrient in higher concentration and fat is the nutrient with the most variation. There is a pronounced amplitude in the total solids content of colostrum, but the average concentration does not vary much between studies (24.7%). Bovine colostrum major components can vary with several factors, such as the region, season, breed, dry period length, and nutritional aspects of the dam. Bioactive components, cells, and microbiome variability are less understood, besides IgG. Regardless, they play crucial distinct roles in the physiological development of the newborn. However, a multi-interactive effect between these components, cells, and microorganisms is more likely to occur. Recently researched components in colostrum like miRNA, nucleo(t)sides, the milk fat globule membrane, oligosaccharides, minor proteins, and the microbiome are examples of promising interest areas of study.

To investigate the bioactivities of fresh garlic and its processed product, black garlic, we conducted comparative analyses of antioxidant, anti-inflammatory, innate immune activation and anti-cancer activities, in addition to chemical composition (sugar, amino acid, polyphenol contents) of these materials. Simultaneous assay using neutrophil-like cells showed that fresh garlic exhibited antioxidant and innate immunostimulatory activities, whereas black garlic displayed a potent anti-inflammatory effect. The antioxidant activity index was correlated with phenol and flavonoid contents, while the innate immunostimulatory activity was correlated with fructan content. Furthermore, some black garlics with low fructose content were found to inhibit the proliferation of UM-UC-3 cancer cells, while other black garlics rich in fructose increased UM-UC-3 cell proliferation. It was shown that the thermal processing steps of fresh garlic could change the composition of sugars, antioxidants, and amino acids, which have different effects on neutrophil-like cells and UM-UC-3 cells, as well as on bioactivities.

The aim of this randomized controlled clinical trial was to compare the 2-year clinical performance of resin composite restorations placed at non-caries cervical lesions (NCCL) with one-step self-etch, total-etch, and selective enamel etch & self-etch adhesive techniques. Thirty-two patients received three resin composite restorations each at NCCLs (Tetric EvoCeram/Ivoclar/Vivadent), bonded with a total-etch adhesive agent (ExciTE F/Ivoclar/Vivadent) and a self-etch (AdheSE One F/Ivoclar/Vivadent) without and with selective enamel etching. All restorations were evaluated by two examiners at baseline, 6-, 12-, 18- and 24-months post-operation regarding retention, caries occurrence, marginal adaptation, and marginal staining. A logistic regression analysis with generalized estimating equations was used. After 2 years, the retention rate was 86,8% for total-etch, 92.26% for self-etch, and 93.63% for selective enamel etching & self-etch. No caries were detected during all the restorations. Concerning marginal adaptation, the clinically perfect restorations were 26.9% for the total-etch technique, 16% for self-etch, and 25,9% for selective enamel etch & self-etch. All three adhesive strategies provided restorations with no significant differences in the retention rate and the marginal adaptation, whereas the total etch yielded better performance for marginal staining. All the restorations were assessed as clinically acceptable after 2 years.

This paper proposes an enhanced Quantum Key Distribution (QKD) protocol by incorporating a Three-Dimensional Angular Momentum Representation (3D AMR) to address vulnerabilities inherent in traditional two-dimensional polarization states-based systems. The 3D AMR method expands the state space, potentially increasing security against sophisticated quantum attacks. We present a theoretical and computational framework that transitions from the conventional two-dimensional polarization to a three-dimensional angular momentum space, which inherently increases the complexity and security of the quantum states used in QKD.

Displacement mapping is a computer graphics technique that enables the design of components with regularly or randomly textured surfaces that can be quickly materialized on a three-dimensional (3D) printer when needed. This approach is in principle more flexible, faster and more economical compared to conventional texturing methods, but the accuracy of the texture depends heavily on the parameters used. The purpose of this study is to demonstrate how to produce a surface-textured part using polygonal (mesh) modeling software and a photopolymerizable resin, and to develop a universal methodology to predict the dimensional accuracy of the model file log combined with a resin 3D printer. The printed components were characterized on a scanning confocal microscope. In the setup used in this study, the mesh size had to be reduced to 10% of the smallest feature size and the textured layer had to be heavily (x4) overexposed to achieve the desired accuracy. As a practical application, two functional stamps with a regular (honeycomb) and a random texture, respectively, were successfully manufactured. The insights gained will be of great benefit in quickly and cost-effectively producing components with innovative patterns and textures for a variety of hobby, industrial and biomedical applications.

This paper presents the design and analysis of a novel 3-degree-of-freedom (3-DOF) parallel ma-nipulator equipped with self-sensing Ni-Ti (Nitinol) actuators. The manipulator's architecture and mechanical design are elucidated, emphasizing the integration of Nitinol actuators. The self-sensing technique implemented in a previous work was extended to a 20 mm actuator length, and the actuator was used to design the 3 DOF manipulator. Kinematic analyses were conducted to eval-uate the manipulator's performance under various operating conditions. A dynamic model was implemented for the dynamic dimensioning of the actuators, which work synergistically with a bias spring. The manipulator was realized, and a control strategy was implemented. Experimental tests, although documenting some positioning accuracy issues, show the efficacy and potential applica-tions of the proposed manipulator in robotics and automation systems, highlighting the advantages of self-sensing Nitinol actuators in small parallel manipulator designs.

Background: Cardiovascular (CV) morbidity and mortality are many times higher in chronic kidney disease (CKD), as well as IgA nephropathy (IgAN), than in the general population. The occurrence of metabolic syndrome (MetS) and metabolic risk factors are independent risk factors for CV disease and renal progression. The study aimed to determine the prognostic role of metabolic profiles in a homogenous group of CKD patients. Methods: One hundred and forty-five IgA nephropathy patients (92 male, 53 female, age 54.7 ± 13 years) with CKD stage 1-4 were investigated and followed for a median of 190 months. The composite (CV and renal) endpoints included all-cause mortality and any CV event such as stroke, myocardial infarction, revascularization (CV), end-stage renal disease, and renal replacement therapy (renal). Results: Patients with MetS had significantly more endpoint events (16/27 patients vs. 15/98 patients, p = 0.001) compared to the nonMetS group. Of the secondary endpoints (CV or renal separately), the rate of the renal and CV endpoints was significantly higher in the MetS group (p = 0.001 and p = 0.029). The primary endpoint independent predictors of survival were dyslipidemia, eGFR, hemoglobin, urine albuminuria, and diabetes mellitus, as determined by Cox regression analysis. Independent predictors of secondary renal endpoint were dyslipidemia, hemoglobin, urine albumin, and eGFR. Predictors of secondary cardiovascular endpoints were gender, BMI, and diabetes. Kaplan-Meier curves showed significant differences in MetS and non-MetS when examined at the combined endpoints (CV and renal) or at each endpoint separately. The primary endpoint rate increased significantly with the increased number of MetS components (MetS comp. 0 vs. MetS comp. 2+, primary endpoints, p = 0.012). Conclusion: Our results showed that the metabolic profile has a prognostic role not only for renal endpoints but also for CV endpoints in IgAN. BMI, hyperuricemia, hypertension, and diabetes have a predictive value for the prognosis of IgA nephropathy.

The effect of wave forces on the structural safety of fixed oscillating water-column (OWC) devices is critical. In this study, a three-dimensional numerical model of an oscillating water column (OWC) device is constructed using the computational fluid dynamics software OpenFOAM. Subsequently, the hydrodynamic performance of the numerical model is comprehensively validated. Finally, the hydrodynamic performance data are analyzed in detail to obtain meaningful conclusions. The results indicate that the horizontal wave force on the OWC device is approximately 6.6 to 7.9 times greater than the vertical wave force, whereas the lateral wave force is relatively small. Both the horizontal and vertical wave forces decrease as the relative water depth increases under a constant wave period and height. The horizontal wave force increases linearly with the wave height, whereas the vertical wave force increases with the square of the wave height. In addition, the highest dynamic water pressure is observed at the interface between the water surface and device, both within and outside the front wall of the gas chamber. The dynamic water pressure at different locations on the front chamber increases and subsequently decreases as the wave frequency increases.

In the present research, it has been tried to use the applied research bases in the field of business management with marketing orientation. Since there were wide and diverse spectrum in the field of economic activities in Isfahan province and Isfahan city, the model of economic sectors was used to categorize these activities. In this regard, the specific goals of the research in all five sectors of the model of economic sectors, drawing and prioritizing the components (in-dices) of the 7P marketing mix model in each of these economic sectors by the related individuals and members of subgroups of guilds and non-governmental organizations in Isfahan province, have been formed, specified and determined. Collecting data for processing and answer the question of this research, after designing a questionnaire in accordance with the AHP model standard, by spending a period of 2 months from September 2022 and ended in November 2022 , from the statistical population has been done.

The North China Plain is among the regions most afflicted by ground fissure disasters in China. Recent urbanization has accelerated ground fissure activity in the three counties of the northern North China Plain, posing significant threats to both the natural environment and socioeconomic sustainability. Despite the increased attention, a lack of comprehensive understanding persists due to delayed recognition and limited research. This study conducted field visits and geological surveys across 43 villages and 80 sites to elucidate the spatial distribution patterns of ground fissures in the aforementioned counties. By integrating these findings with regional geological data, we formulated a causative model to explain ground fissure formation. Our analysis reveals a concentration of ground fissures near the Niuxi and Rongxi faults, with the former exhibiting the most extensive distribution. The primary manifestations of ground fissures include linear cracks and patch-shaped collapse pits, predominantly oriented in east-west and north-south directions, indicating tensile failure with minimal vertical displacement. Various factors contribute to ground fissure development, including fault activity, ancient river channel distribution, bedrock undulations, rainfall, and ground settlement. Fault activity establishes a concealed fracture system in shallow geotechnical layers, laying the groundwork for ground fissure formation. Additionally, the distribution of ancient river channels and bedrock undulations modifies regional stress fields, further facilitating ground fissure emergence. Rainfall and differential ground settlement serve as triggering mechanisms, exposing ground fissures at the surface. This research offers novel insights into the causative mechanisms of ground fissures in the northern North China Plain, providing valuable scientific evidence for mitigating ground fissure disasters during the urbanization process in the region.

Advanced Finite Element (FE) modeling and simulations were performed on vehicular crashes into a Three-bar Metal Bridge Rail (TMBR). The FE models of a sedan, a pickup truck, and a TMBR section were adopted in the crash simulations subject to Manual for Assessing Safety Hardware (MASH) Test Level 2 (TL-2) and Test Level 3 (TL-3) requirements. The test vehicle models were first validated using full-scale physical crash tests conducted on a two-bar metal bridge using a sedan and a pickup truck with similar overall physical properties and sizes to their respective vehicles used in the simulations. The validated vehicular models were then used to evaluate the crash performance of the TMBR using MASH Evaluation Criteria for structural adequacy, occupant risk, and post-impact trajectory. The TMBR met all MASH TL-2 requirements but failed to meet the MASH TL-3 Criteria H and N requirements when impacted by the sedan. The TMBR was also evaluated under in-service conditions (behind a 1.52-m wide sidewalk) and impacted by the sedan under MASH TL-3 conditions. The simulation results showed that the TMBR behind a sidewalk met all safety requirements except for the occupant impact velocity in the longitudinal direction, which exceeded the MASH limit by 3.93%.

The main objective of this study was to compare the removal efficiency of nutrients using Lactuca sativa, Medicago sativa and Phragmites australis in subsurface flow constructed wetlands with horizontal flow. In order to test water quality, fabricated reactors designed and the plants cultivated in the soil while their root were inside the wastewater. A long time study carried out from spring till end of autumn (9 months) in order to evaluate the difference in removal rate based on the seasonal changes. The highest removal rate was during summer which followed by spring and autumn. Thus, the effect of plants on the removal efficiency of organic matter (COD, BOD), TSS and nutrient (P and TN) appeared to be dependent on the seasonal growth. Phragmites australis the most sensitive species in order the removal of nutrient from wastewater.

This research focuses on the Hopf bifurcation occurring at a singular point with high-order degeneracy in a class of three-dimensional systems. Based on center manifold theorem, by expanding the technique for determining singular point values of degenerate singularities in two-dimensional systems, the formal series method to determine the singular point values at the high-order degenerate critical point is discussed. Furthermore, a class of specific three-dimensional differential systems with high-order degenerate singularities is explored. By computing the singular point values and determining center conditions, we proved that a minimum of 5 small-amplitude limit cycles in the vicinity of the origin. This research provides new perspectives on the center problem and limit cycle bifurcation in high-dimensional systems with high-order degenerate singular points.

A power factor correction (PFC) rectifier is compulsory for any electronic circuitry connected to the electrical grid. The majority of PFCs that are utilized are based on a step-up converter that supplies high DC voltage at its output terminal. Electric vehicle battery voltage varies from a few hundred to almost a thousand volts. Thus, an additional conversion step is obligatory when designing an all-brand universal charger. This paper presents a new type of front-end versatile step up / down three voltage level PFC. The rectifier can operate in continuous conduction mode or discontinuous conduction mode. First, the rectifier’s principle of operation is described, and then an innovative rectifier is analyzed for continuous and discontinuous conduction modes. Finally, the proposed theory is experimentally validated in a multiplier-less dual loop mode at discontinuous conduction modes. It was shown that although there is no multiplier use in the control circuitry, the power factor is near unity. It was revealed that the rectifier could swing the output voltage from 50 V to 900 V while the input voltage was 230 Vrms. The innovative topology suits any standard PFC rectifier, three-level voltage supplement, and dual-stage low-voltage power supply.

(1)Background：To date, no studies have epidemiologically examined whether the concentration of particulate matter (PM) 2.5 and its ionic components is related to the prevalence of skin symptoms. Therefore, this study aimed to clarify this association in patients with allergic diseases. (2)Methods: From February 1 to May 31, 2020, we evaluated the daily prevalence of skin symptoms in outpatients with allergic diseases being treated at Fukuoka Hospital, Fukuoka, Japan, and measured the concentration of PM2.5 and its ionic components. （3）Results: Univariate analysis showed a statistically significant association between skin symptoms and the concentration of PM2.5 and the ionic components SO42-, NH4+, K+, and Mg2+, and multivariate analysis showed a statistically significant association between the daily prevalence of skin symptoms and the concentration of the ionic components SO42- or Mg2+. (4)Conclusions: Our findings indicate that the concentration of some PM2.5 ionic components may affect skin symptoms in patients with allergic diseases.

To fulfil a need of limitation automotive emissions the reduction of vehicle weight is widely recommended and achieved in many ways, both by the construction of individual elements of the vehicle, and by the selection of light materials including Al alloys. Connecting these elements with each other and with elements made of iron alloys can be realized, inter alia, by welding or stir welding. However, the quality of the welds obtained varies widely and depends on many design, operational and environmental factors. The present study focused on a review of various welding technics used to joint both similar and dissimilar Al alloys utilized in automotive industry, the effect of various process parameters on welds quality, and phenomena appeared in such welds..

This paper proposed a three-layer distributed simulation network architecture: 1. Distributed virtual simulation network, 2. Perception and control sub-network, and 3. Collaborative communication service network. This simulation architecture runs on a distributed platform. The platform can provide a unique virtual scenario and several simulation services to verify the individual robot system's basic perception, control, and planning algorithms and the distributed collaborative algorithms of heterogeneous multi-robot systems. Furthermore, we designed a simulation experiment scenario for classical heterogeneous robot systems such as unmanned aerial vehicles (UAVs) and unmanned ground vehicles (UGVs). At last, We gave a rough estimation model of the bandwidth.

The AREB/ABF (ABA response element binding) proteins in plants are vital for plant stress responses, but the understanding of AREB/ABFs in orchid species, an important traditional medicinal and ornamental plants, is limited. Here, twelve AREB/ABF genes were identified within three orchids’ complete genome and classified into three groups (groups I, II, and III) via a phylogenetic analysis, which was further supported by the analysis of their conserved motifs and gene structures. The cis-elements analysis showed that hormone response elements followed by light and stress responses were widely rich in AREB/ABFs. A prediction analysis of orchid ABRE/ABF-mediated regulatory network was further constructed through cis-regulatory elements (CREs) analysis of their promoter regions and revealed that several transcriptional factor (TF) gene family were abundant as the potential regulators for orchid AREB/ABFs. Expression profile analysis based on public transcriptomic data showed that most AREB/ABF genes have distinct tissue-specific expression patterns in orchid plants. Additionally, DcaABI5 as the homolog of ABA INSENSITIVE 5 (ABI5) from Arabidopsis was selected for further analysis. The results showed that Arabidopsis transgenic overexpressing DcaABI5 could rescue the ABA insensitive phenotype in the mutant abi5. Collectively, these findings will provide valuable information on AREB/ABF genes in orchids.

Applied talent is not only a builder of human civilization but also a promoter of economic development. They not only need systematic and solid engineering theoretical knowledge but also rich engineering practical experience. Applied undergraduate colleges are the cradle for cultivating applied talent and shoulder the important mission of cultivating various types of applied talent for society. With the rapid development of higher education, the number of applied undergraduate institutions has sharply increased, but the quality of applied talent cultivated by them has shown a significant decline, which greatly restricts the pace of industrial development in the world. This article proposes a new concept of promoting the "three certificates" (graduation certificate, degree certificate, and skill certificate) education model in applied undergraduate colleges, which is of great significance for the country to cultivate composite talents with the ability of "product design, production management, and product processing" at the same time.

Post-Shoah Christology is embedded in the unique relationship of Jews and Christians, especially Jesus’ Jewishness and the Jewish roots of Christianity, as well as Christian moral failures towards Jews before and during the Shoah. Essential for contemporary Christianity, a vibrant post-Shoah Christology confronts three main challenges, each demanding a different response. The first challenge is the reality that soon there will be no more first-generation witnesses to the Final Solution. Such is an inevitable challenge that has to be faced and prepared for. Religious pluralism is the second challenge, and includes a number of related threads, yet should ultimately be embraced. The third challenge is the (inevitable?) loss of memory, passion, and urgency, a willful forgetfulness by Christians towards the importance of the Jewish-Christian relationship, and especially, Christian failure in the Shoah. This challenge demands robust refutation and ongoing struggle. Before addressing these challenges, I will first further define and highlight the need for a post-Shoah Christology and will conclude this article with three general and three concrete hopes for a viable post-Shoah Christology.

Citrus species essential oils (EOs) are significant sources of bioactive compounds and demonstrate diverse therapeutic effects. However, limited documentation exists regarding the phytochemicals associated with their biological activities. This study aims to assess the antioxidant activity, plant inhibitory properties, and brine shrimp cytotoxic effects of EOs derived from three Citrus species: C. sinensis, C. limon, and C. hystrix. Utilizing chemometric analysis and gas chromatography-mass spectrometry (GC-MS) fingerprints, the volatile components contributing to antioxidant activity were elucidated. The peels of the Citrus samples were hydro-distillated to obtain EOs, and subsequently subjected to antioxidant, plant inhibitory, and brine shrimp cytotoxic assays. The results indicated that C. limon EO exhibited the highest antioxidant activity, while C. hystrix and C. sinensis EOs demonstrated pronounced inhibitory effects against Aetrmia salina and Lactuca sativa, respectively. GC-MS analysis facilitated the identification of key compounds in each EO. Principal component analysis (PCA) and hierarchy cluster analysis (HCA) effectively categorized Citrus EOs based on their antioxidant properties, highlighting the proximity of C. limon and C. sinensis. Among the identified compounds, D-limonene, α-Terpineol, Caryophyllene, (+)-3-Carene, β-Pinene, (-)-Spathulenol, trans-p-Mentha-1(7),8-dien-2-ol, and trans-Verbenol were the most discriminating compounds affected the antioxidant activity of C.limon and C. sinensis EOs.

Interferon-gamma release assays (IGRAs) gained attention for diagnosing latent tuberculosis infection (LTBI) due to their higher specificity compared to the tuberculin skin test (TST). However, IGRA performance varied across different populations. This study evaluated the diagnostic performance of three IGRA assays (TBF-FIA, TBF-ELISA, and QFT-Plus) in Ghana, comparing them among individuals exposed and unexposed to MTB infection. Conducted in TB clinics across three regions, this prospective and cross-sectional study included healthy individuals with no known TB exposure (unexposed group) and patients with confirmed active TB (exposed group). Blood samples were tested using all three assays per manufacturers’ guidelines. The TBF-ELISA showed 3.4% higher sensitivity, but 4.6% lower specificity compared to QFT-Plus. The TBF-FIA had a sensitivity of 78.5%-87.3% and a specificity of 82.9%-90.0%. These findings indicated that while the three IGRA assays offered similar diagnostic accuracy, variations in specificity and limited data on point-of-care assays like TBF-FIA required further investigation.

We describe a family of paraxial and quasi-monochromatic optical wave packets with finite energy and smoothly shaped amplitude in space and time that develops a singularity in the intensity when spatiotemporally focused by imparting a converging spherical wave front and a negative temporal chirp. This singular behavior upon ideal focusing is manifested in actual focusing with finite apertures and in media with high-order dispersion in an "exploding" behavior featuring indefinitely increasing concentration of the energy when opening the aperture radius, thus exercising a continuous control on the focal intensity and spatial and temporal resolution. These wave packets offer a new way of focusing that outperforms what can be achieved with standard Gaussian wave packets in terms of focal intensity and resolution, and new possibilities in applications where energy concentration and its control are crucial.

The challenging terrain and deep ravines characteristic of mountainous regions often result in slower path planning and suboptimal flight paths for Unmanned Aerial Vehicles (UAVs) when traditional meta-heuristic optimization algorithms are employed. This study investigates the application of an Improved Enhanced Snake Optimizer (IESO) for three-dimensional path planning in a simulated rugged mountainous terrain. The initialization process in the enhanced snake optimizer is refined by integrating the Chebyshev chaotic map. Additionally, a non-monotonic factor is introduced to modulate the "temperature," and a boundary condition is incorporated into the dynamic opposition learning mechanism. These modifications collectively reduce the likelihood of population convergence to local optima during optimization. The feasibility of IESO is validated through time complexity and global convergence analyses. Comparative simulation experiments benchmarked IESO against five state-of-the-art optimization algorithms across test functions and path-planning simulated scenarios. The experimental results indicate that the enhanced algorithm achieves superior optimization precision, faster convergence speeds, and improved quality in the planned trajectories by 30%.

The prominent cultivation of lemongrass relies on the pharmacological incentives of its essential oil. The lemongrass essential oil (LEO) has a significant amount of citral (mixture of geranial and neral), isoneral, isogeranial, geraniol, geranyl acetate, citronellal, citronellol, germacrene-D, and elemol in addition to numerous other bioactive compounds. These components confer various medicinal activities to LEO including antifungal, antibacterial, antiviral, anticancer, and antioxidant properties. These attributes are commercially exploited in pharmaceutical, cosmetics, and food preservations industries. Furthermore, the employment of LEO in the treatment of cancer opens a new vista in the field of therapeutics. Although different LEO components have shown promising anticancer activities in vitro, these effects have not been assessed yet in humans. Further studies on the anticancer mechanisms exerted by lemongrass components are required. The present review intends to provide a timely discussion on the relevance of lemongrass extracts in cancer and health treatment, and in food industry applications.

The microbial communities are closely related to the overall health and quality of soil, but studies on microbial ecology in apple-pear orchard soils are limited. In the current study, 28 soil samples were collected from three apple-pear orchards in northeastern China, and the composition and structure of fungal and bacterial communities were investigated by high-throughput sequencing. Molecular ecological network showed that the keystone taxa of bacterial communities were Actinobacteria, Proteobacteria, Gemmatimonadetes, Acidobacteria, Nitrospirae, and Chloroflexi, and the keystone taxa of fungal communities was Ascomycota. Mantel tests showed that soil texture and pH were important factors shaping soil bacterial and fungal communities, and soil water soluble organic carbon (WSOC) and nitrate nitrogen (NO3--N) were also closely related to soil bacterial communities. Canonical correspondence analysis (CCA) and variation partition analysis (VPA) analysis revealed that geographic distance, soil texture, pH, and other soil properties could explain 10.55%, 13.5%, and 19.03% of the overall variation of bacterial communities, and they explained 11.61%, 13.03%, and 20.26% of the overall variation of fungal communities, respectively. The key stone taxa of bacterial and fungal communities in apple-pear orchard soils and their strong correlation with soil properties could provide useful clues toward sustainable management of orchards.

In the construction sector, the integration of biobased materials has emerged as a pivotal aspect of EU policies, aimed at promoting sustainable practices throughout the value chain to mitigate resource consumption and carbon emissions. This paper explores the development and validation activities of a bio-based façade system within the Basajaun H2020 project, focusing on enhancing the utilization of biobased components within building envelopes to replace conventional solutions with eco-friendly alternatives. This paper reports the methodologies employed to detect requirements and outline the testing protocols undertaken to validate the façade system design devised within the project focusing on the original façade components as the bio composite profile. Vision and opaque façade modules are prototyped and tested following curtain wall standards standard for performance and acoustic assessments, to showcase the efficacy of the developed solution. The conducted tests demonstrate the feasibility of integrating bio-based components into building envelopes, aligning with project expectations, and prevailing standards for curtain wall façade solutions. Notably, the designed façade system meets technical conditions and project objectives. Nevertheless, the research underscores the need for further refinements to facilitate solution industrialization and explore broader market applicability. Future efforts will focus on addressing these improvements and assessing the scalability of the solution.

The fitting and modeling of skewed, complex, symmetric, and asymmetric datasets is an exciting research topic in many fields of applied sciences, notably lifetime, medical, and financial sciences. The Heavy tailed Nadarajah Haghighi model is introduced by compounding the heavy tailed family and Nadarajah Haghighi distribution in this paper. The so obtained model has three parameters accounting for the scale and shape of the distribution. The proposed distribution's fundamental characteristics such as probability density, cumulative distribution, hazard rate, and survival functions are provided, and several key statistical properties are established, and several entropy information measures are proposed. The estimation of model parameter is performed via the ML procedure. Further, different simulation experiments are conducted to demonstrate the performance of proposed estimator’s using some measure, like the average estimate, the average bias, and associated mean square error. Finally, we are applied our proposed model to analyze three different real datasets. In our illustration, we are compared the practicality of the recommended model with several well-known competing models.

Bone drilling is a common procedure used to create pilot holes for inserting screws to secure implants for fracture fixation. However, dis process can increase bone temperature, teh excessive heat can lead to cell death and thermal osteonecrosis, potentially causing early fixation failure or complications. We conducted a three-dimensional dynamic elastoplastic finite element model to evaluate teh propagation and distribution of heat during bone drilling and assess teh thermally TEMPeffected zone (TAZ) dat may lead to thermal necrosis. dis model investigates teh parameters influencing bone temperature during bone drilling, including drill diameter, rotational speed, feed force, and predrilled hole. Teh results indicate dat our FE model is sufficiently accurate in predicting teh temperature rise TEMPeffect during bone drilling. Teh maximum temperature decreases exponentially wif radial distance. When teh feed forces are 40 and 60 N, teh maximum temperature does not exceed 45 °C. However, wif feed forces of 10 and 20 N, both teh maximum temperature exceeds 45 °C wifin a radial distance of 0.2 mm, indicating a high-risk zone for potential thermal osteonecrosis. Wif teh two-stage drilling procedure, where a 2.5 mm pilot hole is pre-drilled, teh maximum temperature can be reduced by 14 °C. dis suggests dat higher feed force and rotational speed and/or using a two-stage drilling process could mitigate bone temperature elevation and reduce teh risk of thermal osteonecrosis during bone drilling.

This study aimed to evaluate the effect of three yeast strains, Pichia guilliermondii (Levica 27), Candida norvegensis (Levazoot 15), and a commercial product (Levucell® SC 10) containing Saccharomyces cerevisiae, on in vitro rumen fermentation of two substrates: corn stover and a total mixed ration (TMR). Samples were taken 24 hours post-fermentation to measure pH, ammonia nitrogen (NH3-N), gas production, and volatile fatty acid (VFA) concentrations. The addition of yeasts did not affect gas production at 24 hours for either diet. For pH, differences between yeast strains were noted when TMR was used. The lowest NH3-N concentration (6.1 mM) was recorded with corn stover, showing similar results across strains. Conversely, NH3-N levels with TMR ranged from 47 mM to 66 mM. The inclusion of all three yeast strains increased the molar concentrations of total VFA, as well as acetic (C2), propionic (C3), and butyric (C4) acids in the rumen fluid. The C2:C3 ratio remained unchanged with corn stover but decreased with the inclusion of Levica 27 and Levazoot 15 in the TMR. With the commercial product Levucell® SC 10, this ratio was comparable to the control treatment. In conclusion, Levica 27 and Levazoot 15 demonstrated a stimulatory effect on in vitro rumen fermentation for the evaluated diets, evidenced by increased VFA concentrations.

The three-pronged sliding universal coupling is a new kind of three-pronged coupling. To study its kinematic and dynamic characteristics, directional cosine matrices are utilized as tools to analyze the coordinate systems by establishing simplified geometric models and corresponding motions. Through the analysis of the motions of the input and output shafts and employing the method of single-force element, a set of equilibrium equations for the forces acting on the output shaft and the input shaft are formulated for solution analysis. The research indicates that during the rotation process, there exists a small angular difference between the input shaft and the intermediate shaft, demonstrating the quasi-constant angular velocity characteristics of the new tripod sliding universal coupling. The curves of the forces and torques acting on each component of the coupling approximate sinusoidal curves. The optimal operating angle range for the new tripod universal coupling is at angle , during which the system exhibits good transmission and mechanical performance.

Coccomyxa subellipsoidea KJ (C-KJ) is a green alga with unique immunoregulatory characteristics. Here, we investigated the mechanism underlying the modification of T cell function by C-KJ components. The water-soluble extract of C-KJ was fractionated into protein (P) and sugar (S) fractions [acidic (AS), basic (BS), and neutral (NS)]. These fractions were used for the treatment of peripheral blood mononuclear cells stimulated with toxic shock syndrome toxin-1. Transcriptome analysis revealed that both P and AS enhanced the expression of the genes encoding metallothionein (MT) family proteins, inflammatory factors, and T helper (Th) 17 cytokine and suppressed that of those encoding Th2 cytokines in stimulated T cells. The kinetics of MT1 and MT2A gene expression showed a transient increase in MT1 and maintenance of MT2A mRNA after T cell stimulation in the presence of AS. The kinetics of Th17-related cytokine secretion in the early period were comparable to those of MT2A mRNA. Furthermore, our findings revealed that static, a STAT-3 inhibitor, significantly suppressed MT2A gene expression. These findings suggest that the expression of MTs is involved in the immune regulatory function of C-KJ components, which is partially regulated by Th17 responses, and may help develop innovative immunoregulatory drugs or functional foods.

The search of DNA polymorphisms useful for the genetic improvement of dairy farm animals lasts more than 40 years with relevant findings in cattle for milk traits, where the best combination of alleles for dairy processing have been found in casein genes and in the DGAT1. Nowadays, similar results are not reached yet in river buffaloes despite advanced genomic technologies and accurate phenotype records are available. The aim of the present study was to investigate and validate in a larger buffalo population the effect on six milk traits of four single nucleotide polymorphisms (SNP) in the CSN1S1, CSN3, SCD and LPL genes, previously reported to be associated with or affect dairy traits in smaller populations often belonging to one farm. A total of 800 buffaloes were genotyped. Daily milk yield (dMY, kg), protein yield (dPY, kg) and fat yields (dFY, kg), fat and protein contents (dFP, % and dPP, %), somatic cell count (SCC, 103cell/ml) and urea (mg/dl) were individually recorded in each month for the whole lactation from 2010 to 2021. A total of 15,742 individual milk test day records (2,496 lactations) were available on 680 buffalo cows with 3.6±1.7 parity (from 1 to 13) and 6.1±1.2 test day records per lactation on average. Three out four SNP in CSN1S1, CSN3 and LPL were associated with at least one of analyzed traits. In particular, the CSN1S1 (AJ005430:c.578C&gt;T) gave favorable associations with all yield traits (dMY, p=0.022; dPY, p=0.014 ; dFY, p=0.029) and SCS (p=0.032), whereas the CSN3 (HQ677596: c.536C&gt;T) positively associated with SCS (p=0.005) and milk urea (p=0.04). Favorable effect on dMY (p=0.028), dFP (p=0.027) and dPP (p=0.050) were observed for the LPL. Conversely, SCD did not show any association with milk traits. This is the first example of confirmation study carried out in the Mediterranean river buffalo for genes of economic interest in dairy field and it represents a very important indication for the preselection of young bulls destined to breeding programs in the view of a more sustainable dairy production.

Motivation: The visualization of biological data is a fundamental technique that enables researchers to understand and explain biology. Some of these visualizations have become iconic, for instance: tree views for taxonomy, cartoon rendering of 3D protein structures, or tracks to represent features in a gene or protein, for instance in a genome browser. Nightingale provides visualizations in the context of proteins and protein features. Results: Nightingale is a library of re-usable data visualization web components that are currently used by UniProt and InterPro, among other projects. The components can be used to display protein sequence features, variants, interaction data, 3D structure, etc. These components are flexible, allowing users to easily view multiple data sources within the same context, as well as compose these components to create a customized view. Availability: Nightingale examples and documentation are freely available at https://ebi-webcomponents.github.io/nightingale/. It is distributed under the MIT license, and its source code can be found at https://github.com/ebi-webcomponents/nightingale.

Coronavirus disease 2019 (COVID-19) has affected medical practice. More than 7,000,000 patients died worldwide after being infected with COVID-19; however, no specific laboratory markers have yet been established to predict death related to this disease. In contrast, electrocardiographic changes owing to COVID-19 include QT prolongation and ST-T changes; however, there have been no studies on ambulatory electrocardiographic markers of COVID-19. We encountered three patients diagnosed as having COVID-19 who did not have a prior history of significant structural heart diseases. All had abnormalities in ambulatory echocardiogram parameters detected by high-resolution 24-h electrocardiogram monitoring: positive late potentials (LPs) and T-wave alternans (TWA), abnormal heart rate variability (HRV), and heart rate turbulence (HRT). Case 1 involved a 78-year-old woman with a history of chronic kidney disease, Case 2 a 76-year-old man with hypertension and diabetes, and Case 3 a 67-year-old man with renal cancer, lung cancer, and diabetes. None of them had a prior history of significant structural heart disease. Although no significant consistent increases in clinical markers were observed, all three patients died, mainly because of respiratory failure with mild heart failure. LP, TWA, HRV, and HRT were all positive in three cases with no significant structural cardiac disease at the initial phase of admission. There is a possibility that LP, TWA, HRV, and HRT have the potential to be risk stratifiers of COVID-19 pneumonia in the early phase of admission. Further accumulation of data regarding ambulatory electrocardiographic markers in patients with COVID-19 is needed.

A single qubit may be represented on the Bloch sphere or similarly on the 3-sphere S3. Our goal is to dress this correspondence by converting the language of universal quantum computing (UQC) to that of 3-manifolds. A magic state and the Pauli group acting on it define a model of UQC as a positive operator-valued measure (POVM) that one recognizes to be a 3-manifold M3. More precisely, the d-dimensional POVMs defined from subgroups of finite index of the modular group PSL(2, Z) correspond to d-fold M3- coverings over the trefoil knot. In this paper, one also investigates quantum information on a few ‘universal’ knots and links such as the figure-of-eight knot, the Whitehead link and Borromean rings, making use of the catalog of platonic manifolds available on the software SnapPy. Further connections between POVMs based UQC and M3’s obtained from Dehn fillings are explored.

A single qubit may be represented on the Bloch sphere or similarly on the $3$-sphere $S^3$. Our goal is to dress this correspondence by converting the language of universal quantum computing (uqc) to that of $3$-manifolds. A magic state and the Pauli group acting on it define a model of uqc as a POVM that one recognizes to be a $3$-manifold $M^3$. E. g., the $d$-dimensional POVMs defined from subgroups of finite index of the modular group $PSL(2,\mathbb{Z})$ correspond to $d$-fold $M^3$- coverings over the trefoil knot. In this paper, one also investigates quantum information on a few \lq universal' knots and links such as the figure-of-eight knot, the Whitehead link and Borromean rings, making use of the catalog of platonic manifolds available on SnapPy. Further connections between POVMs based uqc and $M^3$'s obtained from Dehn fillings are explored.

The aims of this study are to measure the technical efficiency (TE) of Cambodian household’s rice production and trying to determine its main influencing factors using the stochastic frontier production function. The study utilized primary data collected from 301 rice farmers in three selected districts of Battambang by structured questionnaires. The empirical results indicated the level of household rice output varied according to differences in the efficiency of production processes. The mean TE is 0.34 which means that famers produce 34% of rice at best practice at the current level of production inputs and technology, indicates that rice output has the potential of being increased further by 66% at the same level of inputs if farmers had been technically efficient. Furthermore, between 2013-2015 TE of household’s rice production recorded -14.3% decline rate due to highly affected of drought during dry season of 2015. Moreover, evidence reveals that land, fertilizer, and pesticide are the major influencing input factors of household’s rice production, while disaster, education of household head, family size and other crops’ cultivated area are core influencing factors decreasing TE. Conversely, the main influencing factors increasing TE are irrigated area, number of plot area and sex of household head.

The aims of this study are to measure the technical efficiency (TE) of Cambodian household’s rice production and trying to determine its main influencing factors using the stochastic frontier production function. The study utilized primary data collected from 301 rice farmers in three selected districts of Battambang by structured questionnaires. The empirical results indicated the level of household rice output varied according to differences in the efficiency of the production processes. The mean TE is 0.34 which means that famers produce 34% of rice at best practice at the current level of production inputs and technology, indicates that rice output has the potential of being increased further by 66% at the same level of inputs if farmers had been technically efficient. Furthermore, between 2013-2015, TE of household’s rice production recorded -14.3% decline rate due to highly affected of drought during dry season of 2015. Moreover, evidence reveals that land, fertilizer, and pesticide are the major influencing input factors of household’s rice production, while disaster, education of household head, family size and other crops’ cultivated area are core influencing factors decreasing TE. Conversely, the main influencing factors increasing TE are irrigated area, number of plot area and sex of household head.

In marine ecosystems communication among microorganisms is crucial since the distance is significant if considered on a microbial scale. One of the ways used by microorganism cells to reduce this gap is the production of extracellular vesicles. Marine bacteria release extracellular vesicles (EVs), small membrane-bound structures of 50 to 250 nm diameter, into their surrounding environment. The vesicles contain various cellular compounds, including lipids, proteins, nucleic acids, and glycans. EVs may mediate the communication between microorganisms in aquatic environments thus influencing ecosystem function and determining the structure and composition of microbial populations. This review will focus on marine bacterial EVs analysing their structure, composition, functions, and applications.

Cows produce saliva in very large quantities to lubricate and facilitate food processing. Estimates indicate an amount of 50-150 liter per day. Human saliva has previously been found to contain numerous antibacterial components, such as lysozyme, histatins, members of the S-100 family and lactoferrin to limit pathogen colonization. Cows are dependent of a complex microbial community in their digestive system for food digestion. We wondered how this would influence the content of their saliva. We therefore sampled saliva from five humans and both nose secretions and saliva from six cows and separated the saliva on SDS-PAGE gradient gels and analyzed the major protein bands by LC-MS/MS. The cow saliva was found to be dominated by a few major proteins only, the carbonic anhydrase 6, a pH stabilizing enzyme, and the short palate, lung and nasal epithelium carcinoma-associated protein 2A (SPLUNC2A), also named bovine salivary protein 30kDa (BSP30). This latter protein has been proposed to play a role in local antibacterial response by binding bacterial lipopolysaccharide (LPS) and inhibit bacterial growth, but may instead according to more recent data instead have primarily surfactant activity. Numerous peptide fragments of mucin-5B were also detected in the MS analysis. However, mucins stain poorly by the gel staining solution and they are large and have difficult to enter regular gels why their presence easily are overseen. Interestingly, no major band on gel was detected representing any of the antibacterial proteins indicating that cows may produce them at very low levels not to harm the microbial flora of their digestive system. The nose secretions of the cows primarily contained the odorant protein, a protein thought to be involved in enhancing the sensing of smell by the olfactory receptors to enhance the possibility to quickly sense potential poisonous food components. High levels of secretory IgA was also found in one sample of cow mouth drippings indicating a strong upregulation during an infection. The human saliva we more complex containing both secretory IgA, amylase, carbonic anhydrase 6, lysozyme, histatins and a number of other less abundant proteins.

A novel approach to the remote-control system for the compact multi-crystal energy-dispersive spectrometer for x-ray emission spectroscopy (XES) applications has been developed. This new approach is based on asynchronous communication between software components and on reactive design principles. In this paper, we identify the challenges we have faced, our solution to them as well as the implementation and future development prospects. The main motivation of this work was the development of a new holistic communication protocol that can be implemented to control various hardware components.

Thermal and catalytic pyrolysis of virgin low-density polyethylene (LDPE), high-density polyethylene (HDPE), polypropylene (PP) and mixtures of LDPE/PP were carried out in a 200 ml laboratory scale batch reactor at 460 °C in a nitrogen atmosphere. Thermogravimetric analysis (TGA) was carried out to study the thermal and catalytic degradation of the polymers at a heating rate of 10 °C/min. The amount of PP was varied in the LDPE/PP mixture to explore its effect on the reaction. In thermal degradation (TGA) of LDPE/PP blends, a lower decomposition temperature was observed for LDPE/PP mixtures compared to pure LDPE, indicating interaction between the two polymer types. In the presence of a catalyst (CAT-2), the degradation temperatures for the pure polymers were reduced. The TGA results were validated in a batch reactor using PP and LDPE respectively. Thermal cracking results showed that the oil product contains a significant amount of gasoline (C7 − C12) and diesel (C13 − C20) hydrocarbon fractions. The catalyst enhanced cracking at lower temperatures and narrowed the hydrocarbon distribution in the oil towards the gasoline range fraction (C7 – C12). The result suggests that the oil produced from catalytic pyrolysis of waste plastics has a potential as an alternative fuel.

Extruded polystyrene (XPS) is frequently used in the construction of many different structures. It is therefore necessary to appropriately characterize its mechanical properties to ensure the safety of said structures. Among the available characterization tests, static bending tests are simple and easy to perform; owing to these characteristics, they should be performed more frequently than other tests. However, in static bending tests on XPS, there are several challenges owing to the high flexibility of XPS, and the chosen testing method and sample configuration affect the accuracy of characterization. In this study, three bending properties (Young’s modulus, proportional limit stress, and bending strength) of samples cut from an XPS panel were determined using three-point bending (TPB), four-point bending (FPB), and compression bending (CB) tests with varying sample span/depth ratios, and statistical analyses were performed to determine the relevance of the tests. The experimental results suggest that the TPB and CB tests were more feasible than the FPB test when the span/depth ratio was appropriately determined. However, clear differences were observed in the sample bending properties determined in these tests. In light of these findings, further studies should be conducted to elucidate these differences.

Aquaculture contributes to the sustainable development of food security, marine resource conservation, and economy. Shifting aquaculture feed from fish meal and oil to terrestrial plant-derivatives may result in cost savings. However, many carnivorous fish cannot be sustained on plant-derived materials, necessitating the need for the identification of important factors for farmed fish growth and to investigate whether components derived from terrestrial plants can be used in feed. Herein, we focused on the carnivorous fish leopard coral grouper (P. leopardus) to identify the essential growth factors and clarify their intake timing from feeds. Furthermore, we evaluated the functionality of starch, which are easily produced by terrestrial plants. Results reveal that carbohydrates, which are not considered essential for carnivorous fish, can be introduced as a major part of artificial diet. The development of artificial feed using starch offers the possibility of increasing the growth of carnivorous fish in aquaculture.

Currently, the use of numerical models for reproducing the landscape evolution of a river basin is part of the day-by-day research activities of fluvial engineers and geomorphologists. However, despite landscape modelling is based on a rather long tradition, and scientists and practitioners are trying to schematize the processes involved in the evolution of a landscape since decades, there is still the need for improving both the knowledge of the physical mechanisms and their numerical coding. The present review focuses on the first aspect, discussing the main components of a landscape evolution model and their more common schematizations, presenting possible open questions to be addressed towards an improvement of the reliability of such kind of models in describing the fluvial geomorphology.

Part II, like Part I, discusses geometry, kinematics and statics in detail without taking into account power losses in meshing. The main goal of Part II, however, is to prove that there are complex and structurally coupled planetary gear systems, i.e. containing a closed circuit in which no circulation of power flow is generated. The power flow analysis is also carried out using the direct method, with a slight modification in the way of writing the equations identifying active and passive gears, i.e. at the same time the directions of power flow on all transmission paths. The analysed planetary gear system (PGS) is characterised by mobility equal to 1, i.e. single degree of freedom (DoF). It consists of three subsystems in the form of the 2KH type planetary units connected in series-parallel, specially selected to demonstrate the thesis of this paper. It consists of three subsystems in the form of single planetary subsystems of the 2KH type connected series-parallel, specially chosen to illustrate the thesis of this paper.

The aim of this paper is to provide a new perspective on the conditions for the multiple dimensions of concerns, and to understand why some wind power projects run smoothly while others lead to unexpected outcomes due to local resistance. The paper described how multiple community concerns about wind power project planning can be described using conflict management theory and by using different procedures to handle tangible and intangible concerns. Policy recommendations are given on how: to minimise overflowing and the risk of the conflicts; to avoid “boxing” community concerns in categories; to give more attention to the intangible and less calculable concerns; to secure appropriate and early planning with proactive involvement of local communities.

Three Seas Initiative (3SI) is still an underresearched area and is particularly important due to historical circumstances and economic backwardness. A study was carried out to assess the impact of renewable energy and production generated by the agricultural sector on CO2 emissions in 3SI countries between 2008 and 2020. The study used panel data analysis based on the two-step system generalised method of moments (GMM) and the Dumitrescu-Hurlin panel causality test. The results show that a 1% increase in the value-added generated by agriculture increases CO2 emissions in the countries studied by 0.11%. In contrast, a 1% increase in GDP leads to a 0.29% increase in CO2 emissions. Conversely, when renewable energy consumption increases by 1%, CO2 emissions fall by 0.25% in the countries studied. One way to reduce CO2 emissions from agricultural production in the short term is to increase the share of renewables, which, incidentally, is in line with EU action.

This paper proposes a novel single-stage buck-boost three-Level neutral-point-clamped (NPC) inverter with two independent dc sources coupled for the grid-tied photovoltaic (PV) application, which can effectively solve the unbalanced operational conditions generally appeared between two coupled independent PV sources induced by the unequal irradiation and temperature distribution. The proposed control scheme can simultaneously guarantee the maximum power point (MPP) operation of both PV sources and maintain the output waveform quality. Compared to the traditional two-stage PV inverter, the proposed NPC inverter could reduce the PV array voltage requirement and dc-link capacitors’ voltage rating, meanwhile show the advantage in operational efficiency. MATLAB simulations and the captured experimental results are presented to show the performance of the proposed three-level inverter.

The structure of arylpiperazine moieties as an important pharmacophore could generate wide pharmacological activities．Arylpiperazine derivatives referred in this paper possessed antitumor activity. The title compounds were crystallized by slow evaporation. 2-(4-(2-(4-Phenylpiperazin-1-yl)ethyl)benzyl)isoindoline-1,3-dione(1), 2-(4-(2-(4-(4-Bromophenyl)piperazin-1-yl)ethyl)benzyl)isoindoline-1,3-dione (2) and 2-(4-(2-(4-(4-Chlorophenyl)piperazin-1-yl)ethyl)benzyl)isoindoline-1,3-dione (3) crystallizes in the triclinic space group P-1 with two molecules in the unit cell. The unit cell parameters for 1 are a = 6.9159(14) Å, b = 9.999(2) Å, c = 16.925(3) Å, α = 88.25(3)°, β = 85.14(3) °, γ = 79.22(3) °. The unit cell parameters for 2 are a = 6.9995(14) Å, b = 9.919(2) Å, c = 17.671(4) Å, α= 97.55(3)°, β = 92.19(3) °, γ = 102.23(3) °. The unit cell parameters for 1 are a = 6.9872(14) Å, b = 9.863(2) Å, c = 17.557(4) Å, α=96.81(3)°, β = 91.89(3) °, γ = 101.74(3) °. Pi-pi interactions were observed between molecules, and compound 2 and 3 showed halogen interactions between molecules nearby, which was different from compound 1.

Revenue-sharing (RS) contracts are a common approach to incentivize innovation of upstream suppliers by addressing the uneven profit distribution between upstream and downstream firms. Considering the possible overconfidence characterizing decision makers in the supply chain, we investigate the effect of the RS contract and the tendency of overconfidence of supply chain members on the investment in R&D of key components of products in the context of an upstream supplier that is the leader in the R&D and production of key components. We find that regardless of the bargaining power of either party, a RS contract can increase the R&D investment in key components. Regarding the effects of overconfidence of either downstream manufacturer or up-stream supplier, it can increase the R&D investment in key components. Supplier (manufacturer) overconfidence can harm their own profits but increase the profits of the manufacturer (supplier), and when the level of overconfidence is below a certain threshold, the damage to their own profits is less than the increase in each other's profits, thus benefiting the whole supply chain. In addition, we also find a joint effect of RS contracts and overconfidence: when the bargaining power of the supplier is low, the RS contract has a certain compensatory effect on the loss of their own profits caused by overconfidence.

When there is uncertainty in the value of parameters of the input random components of a stochastic simulation model, two-level nested simulation algorithms are used to estimate the expectation of performance variables of interest. In the outer level of the algorithm (n) observations are generated for the parameters, and in the inner level (m) observations of the simulation model are generated with the value of parameters fixed at the value generated in the outer level. In this article, we consider the case in which the observations at both levels of the algorithm are independent, showing how the variance of the observations can be decomposed into the sum of a parametric variance and a stochastic variance. Next, we derive central limit theorems that allow us to compute asymptotic confidence intervals to assess the accuracy of the simulation-based estimators for the point forecast and the variance components. Under this framework, we derive analytical expressions for the point forecast and the variance components of a Bayesian model to forecast sporadic demand; and we use these expressions to illustrate the validity of our theoretical results by performing simulation experiments using this forecast model.

Exogenous miRNAs derived from dietary substances have been shown to be orally transferred to the mammalian system and proven to remain active to regulate host-gene expression. This way they have become an active area of research as functional food components and aspects for dietary supplementation. They are being studied as a new class of metabolically targeted therapeutics that work through diet manipulation and may hold promise for a therapeutic approach in reducing the risk of life-threatening diseases. However, a substantial amount of evidence also defies this dietary miRNA concept in terms of their absorption, bioavailability, cellular uptake and its physiological effects in the mammalian system. But recent advances in the identification of some unique sequence and structural characteristics of dietary miRNAs and a deeper understanding of their stability in host peripheral blood for its cellular uptake have strengthened the whole concept. The review comprehensively summarizes the mechanism for miRNA extracellular transport, absorption through the gastrointestinal tract (GI), stability in peripheral blood, and cellular uptake in mammalian cells. It recapitulates the shreds of evidence, related to the influence of dietary miRNAs on gene expression based on the source of the origin (plant vs animal), and compares their cross-kingdom behaviour in terms of their unique sequence and stem-loop structure properties that help them to get stabilized in the mammalian system. The review also summarizes the parameters required for maintaining the sustainable uptake and bioavailability of the dietary miRNAs with existing examples of successful in-vivo and in-vitro delivery of dietary miRNA for augmented therapy. Lastly, it provides an overview of the available and required databases, webserver, and tools that can be used for the successful identification of potential dietary miRNA candidates.

Reassessment of the fatigue life for wind turbines structural components is typically performed using deterministic methods with the same partial safety factors as used for the original design. However, in relation to life extension, the conditions are generally different from the assumptions used for calibration of partial safety factors; and using a deterministic assessment method with these partial safety factors might not lead to optimal decisions. In this paper, the deterministic assessment method is compared to probabilistic and risk-based approaches, and the economic feasibility is assessed for a case wind farm. Using the models also used for calibration of partial safety factors in IEC61400-1 ed. 4 it is found that the probabilistic assessment generally leads to longer additional fatigue life than the deterministic assessment method. The longer duration of the extended life can make life extension feasible in more situations. The risk-based model is applied to include the risk of failure directly in the economic feasibility assessment and it is found that the reliability can be much lower than the target for new turbines, without compromising the economic feasibility.

Nucleolin is an RNA binding protein that is involved in many post-transcriptional regulation steps of messenger RNAs in addition to its nucleolar role in ribosomal RNA transcription and assembly in pre-ribosomes. Acetylated nucleolin was found to be associated with nuclear speckles and to co-localize with the splicing factor SC35. Previous nuclear pull down of nucleolin identified several splicing components and factors involved in RNA polymerase II transcription associated with nucleolin. In this report, we show that these splicing components are specifics of the pre-catalytic A and B spliceosomes, while proteins recruited in the Bact, C and P complexes are absent from the nucleolin interacting proteins. Furthermore, we show that acetylated nucleolin co-localized with P-SF3B1, a marker of co-transcriptional active spliceosomes. P-SF3B1 complexes can be pulled down with nucleolin specific antibodies. Interestingly, the alternative splicing of Fibronectin at the IIICS and EDB sites was affected by nucleolin depletion. These data are consistent with a model where nucleolin could be a factor bridging RNA polymerase II transcription and assembly of pre-catalytic spliceosome similarly to its function in the co-transcriptional maturation of pre-rRNA.

The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of &gt;1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.

The fixed and random effects models are popular methods for identifying the causal effects of treatment. First, I introduce the two-way fixed effects model and show a class of the estimators for the random effects models. Misidentification may occur in these models due to the treatment effect heterogeneity. Then, I propose the differential error component models to address such problems while the models exclude the fixed effects of units and time periods and consider the random effects of units and time periods. Meanwhile, I present a simulation of a staggered design and revisit the application in (De Chaisemartin and D'Haultfoeuille, 2020). The results demonstrate that one additional newspaper increases the 0.31% average effect of the presidential turnout and the 1.05% average effect when the newspapers’ changes are non-negative, where the proposed estimators are robust and efficient.

Techniques for the controlled seeding and growth of cracks are urgently required for non-destructive testing technique evaluation, particularly for additive manufactured (AM) samples. This paper describes a method which uses a combination of tensile load and resonance excitation of notched AM samples, with in-situ monitoring of the resonance frequency serving to track crack dimensions. Mechanical low-cycle fatigue cracks, ranging in length from ~0.3 mm to ~5 mm, are successfully created in five AM samples using this technique. The samples are non-destructively characterized using optical microscopy and Nonlinear Resonance (NLR) testing. The exploitation of resonance enables the concentration of a significant number of stress cycles on the samples in much shorter timespans than conventional fatigue testing, enabling high throughput, while utilising compact components. Furthermore, the tracking of resonance frequency shift throughout the process enables non-invasive and non-contact real-time condition monitoring.

The paper investigated the components of savings accumulation in Nigeria over the period 1980 to 2017. Secondary data were collated from World Development Index (WDI). In evaluating the objectives, the study employed the Auto Regressive Distributive Lag (ARDL) and Vector Error Correction Model (VECM) estimation methods. The key findings of the study show that the components of savings identified in literature understudied in the paper specifically, GDP per capita, foreign direct investment, financial deepening, interest rate, inflation rate exchange rate significantly influence savings accumulation in Nigeria either in short run, long run or both. Financial deepening was found statistically significant but influences savings negatively. Inflation rate was statistically insignificant although negative. The result from the VECM causality test revealed that short run and long run causal relationship exist between savings and the afore mentioned components in Nigeria. Hence, the study recommends careful manipulation of the identified savings components in a manner that they will not yield a counterproductive result in the economy rather contribute to the growth of savings and ultimately, the growth of Nigeria economy as a whole. It further recommends that the Nigerian government through its financial institutions encourage savings from both small and big savers which to large extent will assuage the perceived undeserved influence of financial deepening on savings accumulation.

Ionospheric delay has been a critical issue that limits the accuracy of GNSS precise positioning and navigation for single-frequency users, especially in mid- and low-latitude regions where irregularity of ionosphere is often significant. Kriging spatial interpolation techniques have been recently introduced to model the spatial correlation and variability of ionosphere, which intrinsically assume that the ionosphere field is stochastically stationary but does not take the random observational errors into account. In this paper, by treating the spatial statistical information on ionosphere as prior knowledge and based on TEC semivariogram analysis, we use Kriging techniques to spatially interpolate TEC values. By assuming that the stochastic models of both the ionospheric signals and measurement errors are only known up to some unknown factors, we propose a new Kriging spatial interpolation method with unknown variance components for both the signals of ionosphere and TEC measurements. Variance component estimation has been integrated with Kriging to reconstruct regional ionospherical delay. The method has been applied to data from the Crustal Movement Observation Network of China (CMONOC) and compared with the ordinary Kriging and polynomial interpolations with spherical cap harmonic functions, polynomial functions and low-degree spherical harmonic functions. The results have shown that the interpolation accuracy of the new proposed method is better than the ordinary Kriging and polynomial interpolation by about 1.2 TECU and 0.7 TECU, respectively. The root mean squared error of the proposed new Kriging with variance components is within 1.5 TECU and is smaller than those from other methods under comparison by about 1 TECU. When compared with ionospheric grid points, the mean squared error of the proposed method is within 6 TECU and smaller than Kriging, indicating that the proposed method can produce more accurate ionospheric delays and better estimation accuracy.

This paper offers a comprehensive examination of the process involved in developing and automating supervised end-to-end machine learning workflows for forecasting and classification purposes. It offers a complete overview of the components (i.e. feature engineering, model selection, etc), principles (i.e. bias-variance decomposition, model complexity, overfitting, model sensitivity to feature assumptions and scaling, output interpretability, etc), models (i.e. neural networks, regression models, etc), methods (i.e. Cross-Validation, data augmentation, etc), metrics (i.e. Mean Squared Error, F1-score, etc) and tools that rule most supervised learning applications with numerical and categorical data, as well as their integration, automation, and deployment. The end goal and contribution of this paper is the education and guidance of the non-AI expert academic community over complete and rigorous machine learning pipelines and data science practices, from problem scoping to design and state-of-the-art automation tools, including basic principles and reasoning in the choice of methods. The paper delves into the critical stages of supervised machine learning workflow development, many of which are often omitted by researchers due to brevity, and covers foundational concepts essential for understanding and optimizing a functional machine learning workflow, thereby offering a holistic view of task-specific application development for applied researchers who are not AI experts.

There is a great interest in finding antioxidants and products with antimicrobial activities from natural sources. The aim of this study was to obtain and identify the phenolic components and organic acids from Camellia oleifera cake. In addition, their antioxidant and antimicrobial activities were also investigated. The purity of phenolic components and organic acids obtained were 94.1 ± 0.5% w/w and 96.0 ± 0.3% w/w, respectively. There are 15 phenolic components have been detected and identified by HPLC-ESI-MS. Oxalic, citric, acetic, malic, and succinic acids are found to be major organic acids. The phenolic components and organic acids both had good antioxidant capacity, evaluated by 4 antioxidant activity assays (hydroxyl radical scavenging, superoxide radical scavenging, 1,1-diphenyl-2-picryl-hydrazyl radical scavenging and lipid peroxidation inhibition). In addition, the phenolic components and organic acids exhibited significant inhibitory activity against bacteria Staphylococcus aureus, Escherichia coli, Bacillus subtilis, and fungi Mucor racemosus, Aspergillus oryzae, Rhizopus stolonifer. The phenolic components and organic acids from C. oleifera cake both showed good antioxidant capacity and exhibited antimicrobial activities. These results may be useful for the future use of phenolic components and organic acids from C. oleifera cake.

Three species of subfamily Cultrinae currently live in Korea, but Erythroculter erythropterus has been introduced into the Nakdonggang River and has taken over the habitat, reducing the habitat of Culter brevicauda. Only the endangered species C. brevicauda still lives in the Yeongsangang River, and it is necessary to be careful not to introduce E. erythropterus in the future. And Hemiculter eigenmanni is also found throughout the country. In order to effectively manage and conserve the species in its various habitats and against invasions, this study was initiated. The ultrastructure of the egg envelopes of three species of Cultrinae— E. erythropterus, C. brevicauda, and H. eigenmanni, inhabiting the Geumgang and Yeongsangang Rivers were observed. It was found that the zona radiata of the egg envelopes of all three species were divided into two layers–an outer and inner layer, with the outer surface having a non-structural form. This form is characteristic of fishes with muddy, stagnant habitats or spawning grounds. The number of pore canals on the surface of the egg envelopes was 83 for E. erythropterus, 75 for C. brevicauda, and 58 for H. eigenmanni per 10 ㎛2, and the thickness was 7.89±0.34 ㎛, 12.27±0.46 ㎛, and 7.42±0.24 ㎛, respectively. The shape of the micropyle demonstrated a funnel shape narrowing toward the inner diameter in all three species, and the size of the inner diameter was 6.62±0.29 (6.09~7.10) ㎛ in E. erythropterus, 4.19±0.39 (3.39~4.58) ㎛in C. brevicauda, and 3.98±0.46 (3.47~4.93) ㎛in H. eigenmanni. The differences between species were identified in the number of pore canals, thickness, and micropyle inner diameter of egg envelopes, which were species-specific. Our study revealed a morphological mechanism in the egg envelope that prevents the formation of interspecific hybrids, and these features can be taxonomic traits that clarify species names. It also provided useful data for the production (breeding) of the second generation in aquaculture.

A tumbler screen type residual film–impurity mixture wind separator as a key equipment for secondary utilization of farmland residual film. During the working process, the proportion of impurities in the separated waste mulch film intermittently increases, resulting in poor working stability of the device, which may hamper long-term operation. In this study, the material inside the separation unit was continuously monitored, and the main factor affecting separator per-formance was determined to be the challenges in the effective depolymerization of some residual film–impurity mixtures. The principles of agglomeration and depolymerization of the residual film–impurity mixtures were analyzed using computational fluid dynamics (CFD) and discrete element method (DEM) flow-solid coupling simulation methods. The key factor affecting the disaggregation of the mixture was the collision force between the residual film–impurity mixture and the trommel screen. The collision force was maximum when the residual film–impurity mixture first collided with the trommel screen when it was fed into the separation device. As determined by force analyses, the key factors affecting the collision force of the process were the material feeding amount and the structure of the inlet. Furthermore, simulations were carried out for different inlet structure forms; the evaluation index was the maximum collision force of the residual film–impurity mixture agglomerate on the trommel screen. The best disaggregation effect was obtained with a square feed inlet and at a feeding rate of 202 kg/h. A prototype was built using these specifications for verification. The average value of the ratio of impurities in the re-sidual film was 6.966%, the coefficient of variation was 7.38%, and the dispersion of statistical results was small. The ratio of impurities in the residual film was kept constant during the con-tinuous operation of the wind separator. Thus, this study analyzed the agglomerate disaggregation process and provided theoretical insights for deter-mining the optimal structures of the inlets of various cleaning devices and the feeding volumes.

Through the ACE2, a main enzyme of the renin-angiotensin system (RAS), the SARS-CoV2 gains access into the cell, resulting in different complications which may extend beyond the RAS and impact the Arachidonic Acid (ArA) pathway. The contribution of the RAS through ArA pathways metabolites in the pathogenesis of COVID-19 is unknown. We investigated whether RAS components and ArA metabolites can be considered biomarkers of COVID-19. We measured the plasma levels of RAS and ArA metabolites using an LC-MS/MS. Results indicate that Ang1-7 levels were significantly lower, whereas Ang II levels were higher in the COVID-19 patients than healthy control individuals. The ratio of Ang1-7/Ang II as an indicator of the RAS classical and protective arms balance was dramatically lower in COVID-19 patients. There was no significant increase in inflammatory 19-HETE and 20-HETE lev-els. The concentration of EETs was significantly increased in COVID-19 patients, whereas the DHETs concentration was repressed. Their plasma levels were correlated with Ang II concentration in COVID-19 patients. In conclusion, evaluating the RAS and ArA pathway biomarkers could provide helpful information for the early detection of high-risk groups, avoid delayed medical attention, facilitate resource allocation and improve patient clinical outcomes to prevent long COVID incidence.

The paper is a follow-up of a previous investigation and effort to develop the ontology of the smart city (Komninos, N., Bratsas, C., Kakderi, C., and Tsarchopoulos, P. "Smart city ontologies: Improving the effectiveness of smart city applications". Journal of Smart Cities, vol. 1(1), 1-17. https://www.komninos.eu/wp-content/uploads/2015/07/2015-Smart-City-Ontologies-Published.pdf). Since the publication of this article in 2015, research and literature on smart cities have evolved significantly, as have the technologies for digital spaces and applications that support city functions. These developments are reflected in the present form of the smart city ontology 2.0 we propose. It depicts the building blocks of the smart city ontology (technologies, structure, function, planning), and the object properties and data properties that connect structural blocks and classes. The aim of the SCO 2.0 is to provide a better understanding and description of the smart/intelligent city landscape; identify the main components and processes, the terms used to describe them, their definition and meaning; clarify key processes related to the integration of the different dimensions of the smart city, mainly the physical, social, and digital dimensions. The paper is accompanied by an owl file, developing the ontology through the editor Protégé.

Coronavirus disease 2019 (COVID-19) is a global pandemic caused by severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). To contain the virus, numerous preventive measures have been taken including isolation of patients, careful infection control, social distancing, and taking vaccine. So far, new confirmed and death cases are still increasing. SARS-CoV-2 invades cells by using the angiotensin converting enzyme 2 (ACE2). ACE2 is an essential enzyme of the renin-angiotensin system (RAS) which converts angiotensin II (Ang II) to angiotensin (1-7). ACE2 is expressed in different organs, including lung, heart, and kidney. A high number of COVID-19 patients developed kidney injury has been reported. Renal impairment and acute injury are associated with mortality of COVID-19, which is 14-16 times higher than other general patients. Acute Kidney Injury has been occured in 2.9 up to 43% of intensive care unit patients. The increasing evidence show that the components of RAS can activate the complement cascade, and cytokines production. Kidney injury caused by SARS-CoV-2 is related mainly to systemic and local inflammation. Moreover, the uncontrolled immune responses mediated by SARS-CoV-2 including hypercytokinaemia, secondary hemophagocytic lymphohistiocytosis, antibody dependent enhancement, complement system, and phagocytic cells activation can contribute in the virus pathogenesis leading to associated renal dysfunction. However, the role and crosstalk between of RAS components and immune response in mediating kidney injury remain undefined. In this review, we focus on the recent studies to provide the pathogenesis of SARS-CoV-2 interacting with RAS and immune responses to mediate kidney injury.

Metal additive manufacturing (AM) has gained much attentions in recent years due to its advantages including geometric freedom and design complexity, appropriate to a wide range of potential industrial applications. However, conventional metal AM methods have high-cost barriers due to the initial cost of the capital equipment, support and maintenance, etc. This study presents a unique low-cost metal material extrusion (MME) technology. The filaments used have polylactic acid (PLA) as the matrix and metal powders (copper, bronze, stainless steel, high carbon iron, and aluminum) as reinforcements. Using the proposed fabrication technology, test specimens were built by extruding polymer/metal composite filaments, which were then sintered in an open-air furnace to produce solid metallic parts. In this research, the mechanical and thermal properties of the built parts are examined using tensile tests, thermogravimetric-, thermomechanical- and microstructural analysis.

The intrusion of seawater in coastal aquifers in Greece is a particularly widespread phenomenon. The coastline of Greece has a length of 15,147 km. Once groundwater resources are contaminated, remediation strategies are difficult, costly and time consuming. In this paper three coastal aquifer systems of Peloponnese are studied. Initially the main ions and cations were calculated for the three aquifers. According to the results from hydrochemical analyzes Na+,Mg2+, Ca2+, SO4-2, Cl- have high values and are affected by the intrusion of seawater into the coastal aquifers. It estimates the vulnerability of groundwater to the intrusion of seawater. Using Geographical Information Systems (GIS) software, maps are prepared for the presentation of each parameter of the GALDIT method. The main factors that affect the seawater intrusion are basically presented in the 6 letters of the acronym GALDIT. The analysis of each parameter is as follows: Groundwater occurrence (aquifer type: unconfined, confined, and leaky confined), Aquifer hydraulic conductivity, depth to groundwater Level above the sea, Distance from the shore (inland distance perpendicular from shoreline), Impact of existing status of sea water intrusion in the area and Thickness of the aquifer. The final map that emerged from the study of the three groundwater systems shows the vulnerability of seawater intrusion in Peloponnese. The maps show that the groundwater system of Larissos presents lower vulnerability to the seawater intrusion compared to the other two groundwater systems. This is because the occurrence of flysch in the northern part of the area acts as a barrier to the penetration of seawater.

Growth and yield of boreal tree species are discussed. A growth model is applied, along with verified yield models of sawlogs and veneer logs. Using the normal forest-principle, thinning schedules and rotation ages maximizing the estate-level capital return rate are clarified. Regeneration expenses are amortized at the end of any rotation. Consequently, capitalizations are greater and rotations longer than in recent studies. The capital return rate is a weak function of initial stem count but differs by tree species. The initial stem count strongly contributes to biomass stored in trees. The most promising way of increasing the capital return rate is the reduction of regeneration expenses. Thinnings are triggered by stand volumes of at least 200 m3/ha. The average commercial trunk volume of trees removed in thinnings always exceeds 200 liters. Risk aversion theory proposes short rotations and low stem count in seedling planting unless carbon storage compensation exists.

The Standard Model (SM) fails to account for either the triplication of fermion families or chiral symmetry breaking in the electroweak sector. Here we show that both phenomena arise from the approach to chaos of quantum theory near the Fermi scale.