Svoboda | Graniru | BBC Russia | Golosameriki | Facebook

To install click the Add extension button. That's it.

The source code for the WIKI 2 extension is being checked by specialists of the Mozilla Foundation, Google, and Apple. You could also do it yourself at any point in time.

4,5
Kelly Slayton
Congratulations on this excellent venture… what a great idea!
Alexander Grigorievskiy
I use WIKI 2 every day and almost forgot how the original Wikipedia looks like.
Live Statistics
English Articles
Improved in 24 Hours
Added in 24 Hours
What we do. Every page goes through several hundred of perfecting techniques; in live mode. Quite the same Wikipedia. Just better.
.
Leo
Newton
Brights
Milds

MLT-3 encoding

From Wikipedia, the free encyclopedia

Example of MLT-3 Encoding. Light-colored lines indicate two previous states, where : 133710 = 101001110012

MLT-3 encoding (Multi-Level Transmit) is a line code (a signaling method used in a telecommunication system for transmission purposes) that uses three voltage levels. An MLT-3 interface emits less electromagnetic interference and requires less bandwidth than most other binary or ternary interfaces that operate at the same bit rate (see PCM for discussion on bandwidth / quantization tradeoffs), such as Manchester code or Alternate Mark Inversion.

Eye pattern of a MLT-3 signal

MLT-3 cycles sequentially through the voltage levels −1, 0, +1, 0. It moves to the next state to transmit a 1 bit, and stays in the same state to transmit a 0 bit. Similar to simple NRZ encoding, MLT-3 has a coding efficiency of 1 bit/baud, however it requires four transitions (baud) to complete a full cycle (from low-to-middle, middle-to-high, high-to-middle, middle-to-low). Thus, the maximum fundamental frequency is reduced to one fourth of the baud rate. This makes signal transmission more amenable to copper wires.

The lack of transition on a 0 bit means that for practical use, the number of consecutive 0 bits in the transmitted data must be bounded; i.e. it must be pre-coded using a run-length limited code. This results in an effective bitrate slightly lower than one bit per baud or four bits per cycle.

MLT-3 was first introduced by Crescendo Communications[1] as a coding scheme for FDDI copper interconnect (TP-PMD,[2] aka CDDI). Later, the same technology was used in the 100BASE-TX physical medium dependent sublayer, given the considerable similarities between FDDI and 100BASE-[TF]X physical media attachment layer (section 25.3 of IEEE802.3-2002 specifies that ANSI X3.263:1995 TP-PMD should be consulted, with minor exceptions).

Signaling specified by 100BASE-T4 Ethernet, while it has three levels, is not compatible with MLT-3. It uses selective base-2 to base-3 conversion with direct mapping of base-3 digits to line levels (8B6T code).

YouTube Encyclopedic

  • 1/3
    Views:
    23 571
    1 763
    9 200
  • digital signal encoding technique (বাংলা)
  • Three blocks friction problem.
  • Line Coding in Urdu and Hindi

Transcription

See also

External links

References

  1. ^ [1], Network World, June 29, 1992, page 19
  2. ^ American National Standards Institute (1994). "FDDI twisted pair physical layer medium dependent (TP-PMD)". American National Standard X3T12 (Incorporates X3.263). - initial implementation; also see patent
This page was last edited on 21 May 2024, at 15:25
Basis of this page is in Wikipedia. Text is available under the CC BY-SA 3.0 Unported License. Non-text media are available under their specified licenses. Wikipedia® is a registered trademark of the Wikimedia Foundation, Inc. WIKI 2 is an independent company and has no affiliation with Wikimedia Foundation.