This article addresses the trajectory tracking between two non-identical systems with chaotic properties. We employ the Rossler chaotic and RCL-shunted Josephson junctions model in similar phase space to study trajectory tracking. In order to achieve the goal tracking, we afford two stages to approximate the target tracking. The first stage utilizes the active control technique to transfer the output signal from the RCLs-J system into the quasi-Rossler system. Then next, the RCLs-J system employs the proposed the iterative learning control scheme and the control signal from the drive system to trace the trajectory of Rossler system. The numerical results demonstrate the proposed method and the tracking system is asymptotically stable.

This research not only dedicated a less restrictive method of iteration-varying function for a learning control law to design a controller but also synchronize two nonlinear systems with free time-delay. In addition, the mathematical theory of system synchronization has proved rigorously and the theory verified through an example to demonstrate the behavior of each parameter in the theory. The design of a controller using the iterative learning control law is significant for robotic tracking. The controller in this research generates a feed-forward control input using the error dynamics among the drive-response systems. The error dynamics satisfies the Lyapunov function and the combination of output errors, which respectively represented relative estimated differences of the drive-response systems. The iterative learning control rule serves the function of a filter adding previous control error after the end of each iteration. The numerical example of a synchronous system is given a Lorenz system for driving and another with the iterative learning control law for response under different initial condition. The results verify and demonstrate the proposed mathematical theory. The simulation exhibits consistency in the behavior of each parameter to match mathematical theory.

Excretory-secretory products (ESPs) are the main research targets for investigating the hosts and helminths interaction. Parasitic worms can migrate to parasitic sites and avoid the host immune response by secreting this product. Angiostrongylus cantonensisis an important food-borne zoonotic parasite that causes severe neuropathological damage and symptoms, including eosinophilic meningitis or meningoencephalitis in humans. Benzaldehydes are organic compounds composed of a benzene ring and formyl substituents. This compound has anti-inflammatory and antioxidation properties. Previous studies showed that 3-hydroxybenzaldehyde (3-HBA) and 4-hydroxybenzaldehyde (4-HBA) can reduce apoptosis in A. cantonensis ESPs treated astrocytes. These results on the protective effect underlying benzaldehyde have primarily focused on cell survival. The study was designed to investigate the molecular mechanisms of endoplasmic reticulum stress (ER stress) and oxidative stress in astrocytes in A. cantonensis ESPs treated astrocytes and to evaluate the therapeutic consequent of 3-HBA and 4-HBA. First, we initially established the RNA-seq dataset in each group, including Normal, ESPs, ESPs+3-HBA, and ESPs+4-HBA. We also found that benzaldehyde (3-HBA and 4-HBA) can stimulate astrocytes to express ER stress-related molecules after ESP treatment. The level of oxidative stress could also be decreased in astrocytes by elevating antioxidant activity and reducing ROS generation. These results suggested that benzaldehyde may be a potential therapeutic compound for human angiostrongyliasis to support brain cell survival by inducing the expression levels of ER stress- and oxidative stress-related pathway.

This paper presents an efficient topology optimization approach considering fail-safe requirements in the framework of the solid isotropic material with penalization method. Existing methods either are computationally extremely expensive or do not consider fail-safe requirements in the optimization. The current approach not only obtains the fail-safe optimization structure, but also significantly improves the computational efficiency of fail-safe topology optimization. In this method, the worst-case compliance is considered to minimize as the optimization objective, using the Kreisselmeier–Steinhauser function to approximate the non-differentiable max-operator. The sensitivity is derived by the adjoint method, and a general fail-safe optimality criteria method is developed to update design variables. The damage scenarios greatly reduces in the process of failsafe strategy optimization by employing the density-based filter method. Finally, the effectiveness and computational efficiency of this method for fail-safe optimization is verified by several numerical examples.

In this paper we present the exploration of indoor positioning technologies for UAVs, and navigation techniques for path planning and obstacle avoidance. The objective is to perform warehouse inventory tasks using a drone to search for barcodes or markers to identify the objects. For the indoor positioning techniques, we employ Visual-Inertial Odometry (VIO), Ultra-Wideband (UWB), AprilTag fiducial markers, and Simultaneous Localization and Mapping (SLAM). These algorithms encompass global positioning, local positioning, and pre-mapping positioning, comparing the merits and drawbacks of various techniques and trajectories. In UAV navigation, we combine SLAM-based RTAB-Map indoor mapping and navigation path planning of the ROS for indoor environments. This system enables precise drone positioning indoors and utilizes global and local path planners to generate flight paths that avoid dynamic, static, unknown, and known obstacles, demonstrating high practicality and feasibility. To achieve the warehouse inventory inspection, a reinforcement learning approach is proposed to recognize the markers by adjusting the UAV's viewpoint. We address several main problems in inventory management, including efficiently planning paths while ensuring a certain level of detection rate. Two reinforcement learning techniques, AC (Actor-Critic) and PPO (Proximal Policy Optimization), are implemented based on AprilTag identification. Testing is performed in both simulated and real-world environments, and the effectiveness of the proposed method is validated.Code is available at https://github.com/kellen080/Navigation and https://github.com/kellen080/Indoor\_Positioning.

The goal of this paper is to fabricate innovative diaphragm headphones using graphene oxide paper (GOP) and GOP/epoxy nanocomposites (GOPC). Initially, graphene oxide suspension is fabricated, and the vacuum filtration method is adopted to make GOP. Then vacuum bag molding is used to fabricate GOPC from GOP. Hot pressing and associated molds are adopted to fabricate line-indented (GOPC-L) or curve-indented patterns (GOPC-C) on the GOPC. The performance of one kind of GOP and three kinds of GOPC diaphragm headphones is analyzed based on their sound pressure level (SPL) curves achieved by the Soundcheck measurement system. There are four important processing parameters that will influence the performance of the diaphragm, including material type GOP versus GOPC, indented pattern type, sonication time on suspension, and graphene weight fraction in suspension. Compliances of various diaphragms are measured by the Klippel LPM laser measurement system. The results indicate that effects of sonication time and graphene weight fraction on SPL of GOP and GOPC headphones are in reverse, and this is associated with their difference on compliance (modulus), mass, damping ratio, and microstructure uniformity. Either GOPC-L or GOPC-C seems to improve the microstructure of the GOPC, and leads to better SPL performance. The correlation between the previous four factors and SPLs of four kinds of diaphragm headphones is proposed by using scanning electron microscope (SEM) to examine the microstructure of these diaphragms.

A reinforcement learning algorithm is proposed to improve the accuracy of short-term load forecasting (STLF) in this article. The proposed model integrates radial basis function neural network (RBFNN), support vector regression (SVR), and adaptive annealing learning algorithm (AALA). In the proposed methodology, firstly, the initial structure of RBFNN is determined by using SVR. Then, an AALA with time-varying learning rates is used to optimize the initial parameters of SVR-RBFNN (AALA-SVR-RBFNN). In order to overcome the stagnation for searching optimal RBFNN, a particle swarm optimization (PSO) is applied to simultaneously find promising learning rates in AALA. Finally, the short-term load demands are predicted by using the optimal RBFNN. The performance of the proposed methodology is verified on the actual load dataset from Taiwan Power Company (TPC). Simulation results reveal that the proposed AALA-SVR-RBFNN can achieve a better load forecasting precision as compared to various RBFNNs.

Aberrant neutrophil extracellular trap (NET) formation and the loss of barrier integrity in inflamed intestinal tissues have long been associated with inflammatory bowel disease (IBD). However, whether NETs alter intestinal epithelium permeability during colitis remains elusive. Here, we demonstrated that NETs promote the breakdown in intestinal barrier function for the pathogenesis of intestinal inflammation in mouse models of colitis. NETs were abundant in the colon of mice with colitis experimentally induced by dextran sulfate sodium (DSS) or 2,4,6-trinitrobenzene sulfonic acid (TNBS). Analysis of the intestinal barrier integrity revealed that NETs impaired gut permeability, enabling the initiation of luminal bacterial translocation and inflammation. Furthermore, NETs induced the apoptosis of epithelial cells and disrupted the integrity of tight junctions and adherens junctions. Intravenous administration of DNase I, an enzyme that dissolves the web-like DNA filaments of NETs, during colitis restored the mucosal barrier integrity which reduced the dissemination of luminal bacteria, and attenuated intestinal inflammation in both DSS and TNBS models. We conclude that NETs serve a detrimental factor in the gut epithelial barrier function leading to the pathogenesis of mucosal inflammation during acute colitis.

Importance: Because of the high prevalence of myopia in Taiwan, understanding the risk factors for its development and progression is important to public health. Background: This study investigated the risk factors for myopia and their influence on the progression of myopia in schoolchildren in Taiwan. Design: Patients’ clinical records were obtained retrospectively from ophthalmologists. Questionnaires were given to collect demographic information, family background, hours spent on daily activities, myopia progression, and treatment methods. Participants: A total of 522 schoolchildren with myopia from a regional medical hospital in northern Taiwan participated the study. Written informed consent was obtained from the participants of legal age or the parents or legal guardians. Methods: Multivariable regression analyses were performed. Myopia measured in dioptres was analysed, controlling for patients’ family and demographic information as well as their daily behaviours. Main Outcome Results: Children with high myopic parents were more myopic. Earlier onset age of myopia was associated with a higher level of myopia and greater annual myopic progression. Children reporting more near work activities had higher levels of myopia and greater progression of myopia. Lower levels of myopia were associated with more exercise, longer periods of sleep, and better vision care knowledge in children and parents. Intake of food supplements had no effect on myopia. Conclusions and Relevance: In addition to genetics, education, environment, and near work activity can influence the development of myopia. Health policies for schoolchildren should promote protective activities and vision care knowledge in order to protect the eyesight of schoolchildren.

Blood glucose (BG) monitoring is an important issue for critically ill patients. Previous studies reported that poor sugar control was associated with increased mortality in admitted patients. However, repeated blood glucose monitoring can be resource-consuming and cause a healthcare burden in clinical practice. In this study, we aimed to develop a personalized machine-learning model to predict dysglycemia based on electrocardiogram (ECG) findings. The study included patients with more than 20 ECG records during single hospital admission in the Medical Information Mart for Intensive Care III database, focusing on the lead II recordings, along with the corresponding blood sugar data. We processed the data and used ECG features from each heartbeat as inputs to develop a one-class support vector machine (SVM) algorithm to predict dysglycemia. The model prediction for dysglycemia using a single heartbeat had an AUC level of 0.92 ± 0.09, with a sensitivity of 0.92 ± 0.10 and specificity of 0.84 ± 0.04. Based on 10 s majority voting, the model prediction for dysglycemia improved to an AUC of 0.97 ± 0.06. In this study, we found that a personalized machine-learning algorithm could accurately detect dysglycemia using a single-lead ECG.

In the clock network design, the trade-off between power consumption and timing closure is an important and difficult issue. To achieve this target, a hybrid clock network architecture that combines both clock tree and clock mesh seems to be a promising solution. In this paper, we propose a novel clock mesh architecture – cross-mesh, with the average dispersion of the overall driving force, our methodology creates small non-zero skew clock trees. In addition, we integrate clock gating and register clustering techniques to further reduce dynamic power consumption. The proposed algorithms have four stages: cross-mesh planning, register clustering, mesh line connecting, and load balancing. Experimental results show that our methodology and algorithms get feasible solution effectively and improve both power consumption and clock skew simultaneously.

This study aims to implement a SSDBI (single-stage differential boost inverter, SSDBI) applying in a single-stage BESS (battery energy storage system, BESS) topology, which can supply power from lower voltage battery module to AC load. Compared with the common two-stage topology, which has a two-stage converter and higher voltage battery module array, the single-stage topology can reduce the number of cells and components, and improve the power density. In addition, a modified SPWM control was proposed to reduce the control complexity of the SSDBI while improving the THD of the inverter. The modified SPWM control can reduce the duty ratio of the SSDBI and the stress on the components to improve the AC voltage output waveform and reduce the THD value about 2.654%.

The morphological and compositional complexities of keratinized components make feathers ingenious skin appendages adapted to diverse ecological needs. Frizzling feathers, characterized by their distinct curling phenotypes, offer a unique model to explore the intricate morphogenesis in developing a keratin-based bioarchitecture over a wide range of morphospace. Here, we investigated the heterogeneous allocation of α- and β-keratins in flight feather shafts of homozygous and heterozygous frizzle chickens by analyzing the medulla-cortex integrations using quantitative morphology characterizations across scales. Our results reveal intriguing construction of frizzling feather shaft through modified medulla development, leading to a perturbed balance of the internal biomechanics and, therefore, introducing the inherent natural frizzling compared to those from wild-type chickens. We elucidate how the localized developmental suppression of the α-keratin in the medulla interferes with the growth of the hierarchical keratin organization by changing the internal stress in the frizzling feather shaft. This research not only offers insights into the morphogenetic origin of the inherent bending of frizzling feathers but also facilitates our in-depth understanding of the developmental strategies toward the diverse integuments adapted for ecological needs.

It is always a difficult task to assign the peaks recorded from vibrational spectrum. Herein we explored a new pathway of density functional theory (DFT) simulation to present three kinds of spectra of ice XIV and can be referenced as inelastic neutron scattering (INS), IR, and Raman experimental spectrum. The INS spectrum is proportional to phonon density of states (PDOS) while the photon scattering signals reflect the normal vibration frequencies near the Brillouin zone (BZ) center. Based on good agreements with experimental data, we identified the relative frequency and made scientific assignments by normal vibration modes analysis. The debating two hydrogen bond (H-bond) peaks among ice phases from INS have been discussed and the dynamic process of H-bond vibrations were found to be classified into two basic modes. we deduce that two H-bond modes are a general rule among ice family and more works are ongoing to investigate this subject.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

The 2019 novel coronavirus (2019-nCoV) causes novel coronavirus pneumonia (NCP). Given that approved drug repurposing becomes a common strategy to quickly find antiviral treatments, a collection of FDA-approved drugs can be powerful resources for new anti-NCP indication discoveries. In addition to synthetic compounds, Chinese Patent Drugs (CPD), also play a key role in the treatment of virus related infections diseases in China. Here we compiled major components from 38 CPDs that are commonly used in the respiratory diseases and docked them against two drug targets, ACE2 receptor and viral main protease. According to our docking screening, 10 antiviral components, including hesperidin, saikosaponin A, rutin, corosolic acid, verbascoside, baicalin, glycyrrhizin, mulberroside A, cynaroside, and bilirubin, can directly bind to both host cell target ACE2 receptor and viral target main protease. In combination of the docking results, the natural abundance of the substances, and botanical knowledge, we proposed that artemisinin, rutin, glycyrrhizin, cholic acid, hyodeoxycholic acid, puerarin, oleanic acid, andrographolide, matrine, codeine, morphine, chlorogenic acid, and baicalin (or Yinhuang Injection containing chlorogenic acid and baicalin) might be of value for clinical trials during a 2019-nCov outbreak.

Our image recognition system mainly judges whether the left upper limb in the image is the left upper limb or the right upper limb through our deep learning model in the image. The doctor then could give the correct surgical position. From the experimental results, it could be found that the precision rate and recall rate of the intelligent image recognition system proposed in this paper for preventing the upper limb dislocation surgery could reach 98% and 93%, respectively. It proved that our artificial intelligent image recognition system, AIIRS, could indeed assist orthopedic surgeons to prevent the occurrence of left and right dislocation in upper limb surgery. At the same time, this paper also completes the IRB application approval through the prototype experimental results and will conduct the second phase of human trials in the future. It showed that the research results of this paper will be of great benefit and research value to upper limb orthopedic surgery.

Our image recognition system mainly judges whether the left upper limb in the image is the left upper limb or the right upper limb through our deep learning model in the image. The doctor then could give the correct surgical position. From the experimental results, it could be found that the precision rate and recall rate of the intelligent image recognition system proposed in this paper for preventing the upper limb dislocation surgery could reach 98% and 93%, respectively. It proved that our intelligent image recognition system could indeed assist orthopedic surgeons to prevent the occurrence of left and right dislocation in upper limb surgery. At the same time, this paper also completes the IRB application approval through the prototype experimental results and will conduct the second phase of human trials in the future. It showed that the research results of this paper will be of great benefit and research value to upper limb orthopedic surgery.

In a single-center, retrospective study, 22 cases were enrolled and divided into two groups: those who underwent surgical wide excision (group A) and those who did not (group B). The study included 13 cases in group A and 9 cases in group B. In group A, 6 cases solely underwent surgical wide excision, while 7 cases received additional treatments like radiotherapy or chemotherapy. Conversely, in group B, 4 cases received chemotherapy, 4 cases received radiotherapy, and 1 case was managed through observation alone. The mean follow-up time was 60.15 months in group A and 43.44 months in group B, with no significant difference observed. In group A, 9 cases resulted in mortality, whereas 6 cases died within the follow-up period in group B. Lesion-free intervals post-operation were observed predominantly in group A, while 7 cases in group B never experienced freedom from skin lesions. Kaplan-Meier survival curve analysis demonstrated a significant difference between the survival curves of the two groups (P = 0.046). Among non-HIV Kaposi’s sarcoma patients, surgical wide excision appears to have a role in treatment. Patients in group A exhibit a more favorable outcome in the survival curve analysis.

Thought runs through the mind like blood runs through our body to keep us alive. Like the mind, the body does not stay inert and is in constant motion. Not a single cell in our body is left inert unless cell is under stress or dying. These scenarios are reflected upon when a person is sick, the person lies in bed with less movement; however, is active when the person is healthy. The topic of mechanical stimulation has emerged due to the increasing understanding of the physical stimulations we face each day. Further understanding of the mechanically-regulated mechanism can help us explore the pathological events in a disease. Here, we reviewed the role of sensory proteins in pathological events that are observed in cardiomyopathy, cancer, respiratory, renal, obesity, genetics, physical injury and bacterial infection. Taken together, sensory proteins are mechanically-activated which assist reception of external physical stimulation and convert into biochemical to trigger intracellular signaling cascade.

We investigated whether post-exercise capsinoids (CSN) supplementation could enhance muscle glycogen resynthesis via GLUT4/Akt expressions in human skeletal muscle. Nine male college students (aged 21.4±0.2 years, BMI 21.9±1.3 kg/m2, VO2max 47.1±1.8 ml/kg/min) participated in this crossover designed study, and completed a 60-min cycling exercise at 70% VO2max. Immediately after exercise, participants consumed high-carbohydrate diet (2 g carb/kg bodyweight) with CSN (12 mg, single dosage) or placebo. Biopsied muscle samples (vastus lateralis) were obtained immediately (0h) and 3h after exercise. Blood and expired gas samples were collected before and after exercise. We found oral CSN supplementation immediately after exercise was unable to enhance glycogen resynthesis in exercised human skeletal muscle. Despite, CSN could alter the energy reliance on fat oxidation during post-exercise recovery, based on gaseous exchange measurement (NEFA and glycerol). We further identified no significant differences in postprandial glucose/insulin area under curve in both trials. Western blot data showed no significant response of p-Akt/Akt ratio with CSN during post-exercise recovery. Inconsistent with glycogen levels, muscle GLUT4 expression was significantly elevated at 3h in CSN trial. Our findings emphasize the necessity of further evidences to confirm the ergogenic properties of CSN in connection with glycogen recovery in exercised human skeletal muscle.

Taiwan developing offshore wind power to promote green energy and self-electricity production. In this study, a Light Detection and Ranging (Lidar) was set up at Chang-Hua development zone one on the sea and 10km away from the seashore. At Lidar location, WRF (3.33km & 2km grid lengths) model and WAsP were used to simulate the wind speed at various elevations. Three days mean wind speed of simulated results were compared with Lidar data. From the four wind data sets, developed five different comparisons to find an error% and R-Squared values. Comparison between WAsP and Floating Lidar was shown good consistency. Lukang meteorological station 10 years wind observations at 5m height were used for wind farm energy predictions. The yearly variation of energy predictions of traditional and TGC wind farm layouts are compared under purely neutral and stable condition. The one-year cycle average surface heat flux over the Taiwan Strait is negative (-72.5 (W/m2) and 157.13 STD), which represents stable condition. At stable condition TGC (92.39%) and 600(92.44%), wind farms were shown higher efficiency. The Fuhai met mast wind data was used to estimate roughness length and power law exponent. The average roughness lengths are very small and unstable atmosphere.

In order to make full use of the complementarity of existing navigation systems to improve the navigation and positioning accuracy, this paper investigates the visual/INS integrated navigation system based on the factor graph optimization (FGO) algorithm. In the traditional visual/INS integrated navigation system, there is often the problem of image blurring due to the rapid change of light and shadow captured by the vision sensor and the attitude change of the carrier, which leads to the decrease of the positioning accuracy of the combined navigation system. Therefore, this paper firstly introduces Retinex algorithm and BID algorithm to carry out the design of image de-blurring method; then implements the visual/INS integrated navigation algorithm based on the factor graph optimization method; finally, the experimental scheme is designed, comparative experiments are carried out, and the researched method is verified by using the public dataset. The experimental results show that the combined navigation algorithm realized in this paper has high accuracy, and its positioning accuracy is improved by 40% compared with visual positioning.

Studies on the neurobiological causes of anxiety disorders suggest that the GABA system in-creases synaptic concentration and enhances the affinity of GABAA (type A) receptors for ben-zo-diazepine ligands. Flumazenil antagonizes the benzodiazepine binding site of the GABA (γ-aminobutyric acid) type /benzodiazepine receptor (BZR) complex in the central nervous sys-tem (CNS). The integration of the metabolites of flumazenil by LC-tandem mass spectrometry will complete understanding of the in vivo metabolism of flumazenil and accelerate radio-pharmaceutical inspection and registration. The main goal of our study was to investigate using reversed-phase HPLC (PR-HPLC) coupled with electrospray ionization triple quadrupole tan-dem mass spectrometry (ESI-QqQ MS) for the identification of flumazenil and its metabolites in a hepatic matrix. And a carrier-free nucleophilic fluorination with automatic synthesizer for [18F]flumazenil which applied to in vivo nano-positron emission tomography (Nano-PET)/computed tomography (CT) imaging and ex vivo bio-distribution used to analyze in normal rats. The study showed that 50% of the flumazenil was bio-transformed at 60 min by the rat liver homogenate, while one metabolite (M1) was a methyl transesterification product of flumazenil. In a rat liver microsomes system, two metabolites were identified (M2 and M3) as its carboxylic acid and hydroxylated ethylester forms, respectively. [18F]flumazenil in vivo nanoPET/CT imag-ing and ex vivo bio-distribution assay also showed significant effects on GABAA receptor availa-bility in the amygdala, prefrontal cortex, cortex, and hippocampus in the rat brain, worriless about the formation of metabolites. We showed completion of the bio-transformed course of flumazenil by the hepatic system; and [18F]flumazenil can be a good ligand and serve as a PET agent for determination of GABAA/BZR complex for multiplex neurological syndromes in the clinical stage.

Although several carbon sequestration methods have been proposed according to theories from various disciplines, it is not known which method is the best. This study evaluated and summarized the advantage and disadvantages of several major carbon sequestration methods, including carbon capture and sequestration, ocean alkalinization, algal cultivation, and wood burial, based on the first principles, namely, sequestration scale and time, elemental stoichiometry, and energy use efficiency. This study suggested that, at present, wood burial may be a leading candidate for carbon sequestration because it can be implemented immediately on a large scale, is cost-effective and efficient, has a long sequestration time, has low technical requirements, and has a relatively low impact on agriculture. This study also discussed the implementation of wood burial from the perspective of nutrient requirements. To achieve carbon neutrality by 2050, the present study proposed a 25-year project starting in 2025 with an average sequestration rate of 3 Pg C per year, which includes burying 1.5 Pg of dead wood carbon and the creation of 9.7 × 10⁶ ha woodland.

Oral cancer ranks sixth among Taiwan's top 10 cancers, and most patients with poor prognosis acquire metastases. The essential fatty acid alpha-linolenic acid (ALA) has been found to diminish many cancer properties. However, the anti-cancer activity of ALA in oral cancer has yet to be determined. Migration and invasion assays confirmed OSCC cells' EMT capabilities, whereas flow cytometry and Western blotting identified the molecular pathways. ALA dramatically reduced cell growth in a concentration dependent manner, according to the findings. Low concentrations of ALA (100 or 200 μM) inhibit colony formation, expression of Twist and EMT-related proteins, expression of MMP2/-9 proteins and enzyme activity, as well as cell migration and invasion. Treatment with high concentrations of ALA (200 or 400 μM) greatly increases JNK phosphorylation and c-jun nuclear accumulation, then upregulates the FasL/caspase8/caspase3 and Bid/cytochrome c/caspase9/caspase3 pathways, leading to cell death. Low concentrations of ALA inhibit SAS and GNM cell migration and invasion by suppressing Twist and downregulating EMT-related proteins, or by decreasing the protein expression and enzyme activity of MMP-2/-9, whereas high concentrations of ALA promote apoptosis by activating the JNK/FasL/caspase 8/caspase 3-extrinsic pathway and the Bid/cytochrome c/caspase 9 pathway. ALA demonstrates potential as a treatment for OSCC patients.

The black hole (BH) phenomenon is an intraluminal restenotic lesion. It was identified by intravascular ultrasound (IVUS) and optical coherence tomography (OCT) after intracoronary brachytherapy and drug-eluting stent implantation. Despite the similarity in the mode of action of brachytherapy and drug-eluting stent implantation, the BH phenomenon appears to be uncommon after drug-eluting stent implantation. Specifically, the BH phenomenon is better identified by OCT than by IVUS. Herein, we present a case of in-stent restenosis with suspected BH phenomenon on IVUS confirmed by OCT.

The Digital Twin is one of the big technology trends of the last decade. In the course of its rapid expansion into the various fields of application, many different definitions emerged, tailored to the respective applications. Taxonomies can cluster the diversity and define application-specific archetypes. This paper presents a characterization of the Digital Twin in the context of structural mechanics and lightweight design. It begins by exploring various definitions of the Digital Twin concept and its application in different industries. The paper further analyzes the product life cycle of structures, dividing it into the design and operational phases and identifying the requirements for a Digital Twin in each phase. The structural design process is examined, including the definition of a structure and the stages of the product development process. Additionally, the paper discusses the operational phase of structures, highlighting the need for continuous monitoring, evaluation, and adaptation through Structural Health Monitoring (SHM) systems. The paper proposes two archetypes of Digital Twins for structures: a structure-designing Digital Twin for the design phase and a structure-monitoring Digital Twin for the operational phase. The findings provide a framework for implementing Digital Twins in structural mechanics, enabling digital design and monitoring of structures for improved performance and maintenance strategies.

On 17 October 1947, Niels Bohr was made a knight of the Order of the Elephant by the King of Denmark in view of his outstanding achievements and contributions to science. Bohr designed his own coat of arms that featured a pattern of Yin and Yang (Tai Chi symbol) to symbolize the wave-particle complementarity. However, Bohr’s Yin-Yang diagram (YYD) was neither drawn based on the principles of quantum mechanics, nor did it originate from the traditional Taoist YYD. Scientists still have doubts about the legitimacy of using YYD as the icon of the wave-particle complementarity, because the YYD belonging to quantum mechanics itself is unknown so far. This article reports the YYDs existing in quantum mechanics and justifies the role of YYD in the wave-particle duality by showing that any system, whether classical or quantum, has an ideal YYD as long as it satisfies Bohr’s principle of complementarity (BPC). The deviation of a deformed YYD from the ideal YYD indicates the extent to which a real system satisfies BPC. This article constructs the quantum YYD by the complex quantum trajectory of a particle tunneling via a step barrier, which displays the continuous transition between the wave behavior and the particle behavior. It appears that the YYD designed by Bohr in his coat of arms resembles the YYD generated by tunneling motion, not only in appearance but also in the governing equation.

Concrete cracks and local damage can affect the bond performance between concrete and steel bars, thereby reducing the durability of reinforced concrete structures. Compared with general concrete crack repair methods, biomineralization repair not only has effective bonding capabilities but is also particularly environmentally friendly. In view of this, this study aimed to apply biomineralization technology to repair damaged fiber-reinforced lightweight aggregate concrete (LWAC). Two groups of LWAC specimens were prepared. The control group used lightweight aggregates (LWAs) without bacterial spores and nutrient sources, and the experimental group used LWAs containing bacterial spores and nutrient sources. These specimens were first subjected to compression tests and pull-out tests, respectively, and thus were damaged. After the damaged specimen healed itself in different ways for 28 days, secondary compression and pull-out tests were conducted. The self-healing method of the control group involved placing the specimens in an incubator. The experimental group was further divided into experimental group I and experimental group II. The self-healing method of experimental group I was the same as that of the control group. The self-healing method of experimental group II involved soaking the specimen in a mixed solution of urea and calcium acetate for two days, and then taking it out and placing it in an incubator for two days, with a cycle of four days. The test results showed that, compared with the control group specimens, the relative bond strength ratio of the experimental group II specimens increased by 17.9%. Moreover, the EDS and XRD analysis results confirmed that the precipitate formed at the crack was calcium carbonate, which improved the compressive strength and bond strength after self-healing. This indicates that the biomineralization maintenance method used in experimental group II is more effective.

Adaptive bitrate (ABR) algorithms optimize the quality of streaming experiences for users in client-side video players especially in unreliable or slow mobile networks. Several rule-based heuristic algorithms can achieve stable performance, but they sometimes fail to adapt properly to changing network conditions. Fluctuating bandwidth may cause algorithms to default to behavior that creates a negative experience for the user. ABR algorithms can be generated with reinforcement learning, a decision-making paradigm in which an agent learns to make optimal choices through interactions with an environment. Training reinforcement learning algorithms for bitrate streaming requires building a simulator for an agent to experience interactions quickly; training an agent in the real environment is infeasible due to the long step times in real environments. This project explores using supervised learning to construct a world-model, or a learned simulator, from recorded interactions. A reinforcement learning agent trained inside of the learned model, rather than a simulator, can outperform rule-based heuristics. Furthermore, agents trained inside the learned world-model can outperform model-free agents in low sample regimes. This work highlights the potential for world-models to quickly learn simulators, and to be used to generate optimal policies.

The PII protein is an evolutionary highly conserved regulatory protein from bacteria to higher plants. In bacteria it modulates the activity of several enzymes, transporters and regulatory factors by interacting with them and thereby regulating important metabolic hubs like carbon/nitrogen homeostasis. More than two decades ago the PII protein was characterized for the first time in plants, but its physiological role is still not sufficiently resolved. To gain more insights into the function of this protein, we investigated the interaction behaviour of AtPII with candidate proteins by BiFC and FRET/FLIM in planta and with GFP/RFP traps in vitro. In the course of these studies we found that AtPII interacts in chloroplasts with itself as well as with known interactors like NAGK in dot-like aggregates, which we named PII foci. In these novel protein aggregates AtPII interacts also with yet unknown partners, which are known to be involved in plastidic protein degradation. Further studies revealed that the C-terminal part of AtPII is crucial for the formation of PII foci. Altogether, the presented results indicate a novel mode of interaction for PII proteins with other proteins in plants, which may be a new starting point for the elucidation of physiological functions of PII proteins in plants.

In Taiwan, mountainous areas account for approximately two-thirds of the total area. The steep terrain and concentrated rainfall during typhoons cause landslides, which pose a considerable threat to mountain settlements. Therefore, models for analyzing rainfall-induced landslide hazards are urgently required to ensure adequate land use in mountainous areas. In this study, focusing on Pingtung County in southern Taiwan, we developed a landslide hazard index (IRL) to land use. Using FORMOSA-2 and SPOT-5 satellite images, data were collected before and after four typhoons (one in 2009 and three in 2013). The ArcGIS random tree classifier was used for interpreting satellite images to explore surface changes and disasters, which were used to analyze slope disturbances. The product of the maximum 3-h rolling rainfall intensity and effective accumulated rainfall was used as a rainfall trigger index (IRT). Considering environmental and slope disturbance factors, an index of slope environmental strength potential (ISESP) was developed through logistic regression (LR). Landslide hazard to land use was estimated using IRT and ISESP. The average coefficient of agreement (Kappa) was approximately 0.71 (medium to high accuracy); the overall accuracy of slope environmental strength potential analysis was approximately 80.4%. At a constant ISESP, IRT increased with the increasing hazard potential of rainfall-induced landslides. Furthermore, IRT and ISESP were positively correlated with landslide occurrence. When large ISESP values occur (e.g., fragile environment and high land development intensity), small IRT values may induce landslides.

Plant-microbe interactions are essential for ecosystem health and agricultural productivity. Metabolomics has revolutionized our understanding of these interactions by providing powerful methods to decipher the complex chemical signals involved. This review highlights the various metabolomics techniques used to study plant-microbe interactions, such as mass spectrometry, nuclear magnetic resonance spectroscopy, and advanced imaging technologies. We also discuss the role of contemporary bioinformatics tools, extensive databases, and the increasing influence of artificial intelligence and machine learning in the analysis of metabolomics data. Integrating metabolomics with other omics fields, including transcriptomics, proteomics, and metagenomics, allows for a comprehensive understanding of the molecular mechanisms underlying plant-microbe interactions. The review emphasizes the significance of fluxomics in elucidating the dynamic nature of metabolic networks. While there are challenges in data analysis, integration, and interpretation, metabolomics has profoundly expanded our knowledge of the role metabolites play in shaping plant-microbe interactions. As metabolomics technologies advance and integrate further with other omics approaches, we anticipate groundbreaking discoveries that will provide deeper insights into these complex interactions, ultimately leading to innovative strategies for sustainable agriculture and biotechnology.

Firstly, a new set of Quasi-Cubic Trigonometric Bernstein basis with two tension shape parameters is constructed, and we prove that it is an optimal normalized totally basis in the framework of Quasi Extended Chebyshev space. And the Quasi-Cubic Trigonometric Bézier curve is generated by the basis function and the cutting algorithm of the curve are given, the shape features (cusp, inflection point, loop and convexity) of the Quasi-Cubic Trigonometric Bézier curve are analyzed by using envelope theory and topological mapping; Next we construct the non-uniform Quasi-Cubic Trigonometric B-spline basis by assuming the linear combination of the optimal normalized totally positive basis have partition of unity and continuity, and its expression is obtained. And the non-uniform B-spline basis is proved to have totally positive and high-order continuity. Finally, the non-uniform Quasi Cubic Trigonometric B-spline curve and surface are defined, the shape features of the non-uniform Quasi-Cubic Trigonometric B-spline curve are discussed, and the curve and surface are proved to be continuous.

The Range–Doppler (R-D) model is extensively employed for the geometric processing of Synthetic Aperture Radar (SAR) images. Refining the sensor motion state and imaging parameters is the most common method for achieving high-precision geometric processing using the R-D model, comprising a process that involves numerous parameters and complex computations. In this study, we introduce a novel approach to improve the positioning accuracy of the R-D model, implementing a low-order polynomial to compensate for the original imaging errors without altering the initial positioning parameters. We also design low-order polynomial compensation models with different parameters. The models are evaluated on various SAR images from different platforms and bands, including spaceborne TerraSAR-X and GF3-C images, manned airborne SAR-X images, and unmanned aerial vehicle-mounted miniSAR-Ku images. Furthermore, image positioning experiments involving the use of different polynomial compensation models and various numbers and distributions of Ground Control Points (GCPs) are conducted. The experimental results demonstrate that geometric processing accuracy comparable to that of the classical rigorous positioning method can be achieved even when applying only an affine transformation model to the images. Compared to classical refinement models, however, the proposed image-compensated R-D model is much simpler and easy to implement. Thus, this study provides a convenient, robust, and widely applicable method for the geometric positioning processing of SAR images, offering a potential approach for the joint-positioning processing of multi-source SAR images.

There are four categories of medical waste that cannot be mixed as this will cause serious problems such as environmental pollution or infection. In the past, the classification of medical waste often involved a lot of human and material resources to process, with workers at risk of exposure to infectious substances. Therefore, an augmented reality (AR) and artificial intelligence (AI) medical waste classification system and method were developed. This innovative medical waste classification system and method combines AR and AI identification technology to reduce the risk of manual judgment errors by clinical staff when handling medical waste.

A overview on application of CO2 in the ironmaking and steelmaking process is presented. Study on resource utilization of CO2 is significant for the reduction of CO2 emissions and the coping with global warming. The paper introduces the research progress of CO2 utilization in the sintering, Blast Furnace, Converter, secondary refining, Continuous Casting and smelting process of stainless steel in recent years in China. According to the foreign and domestic research and application status, the paper analyzes the feasibility and metallurgical effects of the CO2 utilization in the ferrous metallurgy process. The paper mainly introduces such new techniques as 1) flue gas circulating sintering, 2) blowing CO2 through Blast Furnace tuyere and CO2 as a pulverized coal carrier gas, 3) top and bottom blowing CO2 in the converter, 4) Ladle Furnace and Electric Arc Furnace bottom blowing CO2, 5) CO2 as Continuous Casting shielding gas, 6) CO2 for stainless steel smelting, and 7) CO2 circulation combustion. CO2 has a very wide application prospect in ferrous metallurgy process and the quantity of CO2 utilization is expected to be 100kg per ton of steel. It will effectively facilitate the progress of metallurgical technology and strongly promote the energy conservation of metallurgical industry.

Greenhouse gas (GHG) emissions from human activities have climbed significantly above pre-pandemic levels and reached record highs that unequivocally accelerate global warming. Industry has a significant impact on climate change, emitting at least 21 % of global GHGs and making little overall progress toward its reduction until now. Reducing industry’s emissions requires coordinated action along the value chains in order to promote mitigation options, such as energy and material efficiency, circular material flows, and transformative changes within production processes. The authors analyzed the GHG emissions generated during the manufacturing of three different products of automotive suppliers located in Austria. Despite previous efforts toward an environmentally compatible fabrication, additional and significant reduction potentials were identified. These measures for product carbon footprint (PCF) reduction included the sourcing of low-carbon materials (which are already available on the market), more extensive use of renewable energy, and changes towards more resource efficient manufacturing processes and machinery. Depending on the materials used, the PCF can be reduced by up to 80 %. The findings serve to prepare for future PCF reporting regulations and illustrate reduction potentials to achieve future market advantages, especially when PCFs become an awarding criterion.

Soil organic matter (SOM) is essential for nutrient cycling and soil carbon (C) accumu-lation, both of which are heavily influenced by the quality and quantity of plant litter. Since SOM dynamics in relation to plant diversity are poorly understood we investigated the effects of willow variety and mixture, and site on the soil C stocks, SOM chemical composition and ther-mal stability. Using pyrolysis-field ionization mass spectrometry we analysed the top 10 cm of soil from two 7-year-old experimental sites in Germany and Sweden, with monocultures and mixtures of two willow varieties (Salix spp.) belonging to different species. Overall, site had the strongest effect on SOM quality. Results showed significant variability across sites for willow identity and mixture effects on C accumulation and SOM chemistry. In the German site (Ros-tock), yearly soil C accumulation was higher (p < 0.05) for variety ‘Loden’ (1.0 Mg C ha-1 year-1) compared to ‘Tora’ (0.5 Mg C ha-1 year-1), whilst in the Swedish site (Uppsala), both varieties ex-hibited similar soil C accumulation rates of around 0.6 Mg C ha-1 year-1. Willow variety identity significantly affected SOM quality at both sites, while mixing had minor effects. Our findings emphasize the significance of site-specific context and variety or species identity in shaping soil C accumulation in willow plantations.

Heritage conservation area designation is often resisted by communities due to concerns with overly strict regulations for property alterations and negative impacts on property values. This paper addresses these concerns by examining Freemans Bay and Onehunga – two Special Character Areas (SCAs) in Auckland, New Zealand. A property value analysis was used to assess the impact of SCA designation on property values and an online questionnaire survey gathered information on homeowners’ experiences and levels of satisfaction with living in an SCA. The results indicate that designated SCA properties have higher average values than non-designated properties and homeowners are overwhelmingly satisfied with living in a SCA. The main benefits are a sense of community and having certainty around the look and feel of their neighbourhood into the future. The main issue identified by respondents is the requirement for Resource Consent. The majority of people who had gone through the process found it to be a negative experience because of the high cost in terms of time and money. A historic urban landscape approach to the development of management plans and design guidelines is recommended to improve the implementation of the Special Character Areas in Auckland and beyond.

Recycling waste products is an environmental-friendly activity that can bring benefits to accompany, saving manufacturing costs and improving economic efficiency. For the beer industry, recycling bottles can reduce manufacturing costs and reduce the industry's carbon footprint. This paper presents a model for a multi-objective collection-distribution center location and allocation problem in a closed loop supply chain for the beer industry, in which the objective is to minimize total costs and transportation pollution. Uncertainties in the form of randomness and fuzziness are jointly handled in this paper to ensure a more practical problem solution, for which returned bottle sand unusable bottles are considered fuzzy random variables. A heuristic algorithm based on priority-based global-local-neighbor particle swarm optimization (pb-glnPSO) is applied to ensure reliable solutions for this NP-hard problem. A case study on a beer operation company is conducted to illustrate the application of the proposed model and demonstrate the priority-based global-local-neighbor particle swarm optimization.

The fluorine-less noble-gas containing anions OBONgO- and OCNNgO-have been studied by correlated electronic structure calculation and density functional theory. The obtained energetics indicates that for Ng = Kr and Xe, these anions should be kinetically stable at low temperature. The molecular structures and electron density distribution suggests that these anions are stabilized by ion-induced dipole interactions with charges concentrated on the electronegative OBO and OCN groups. The current study shows that in additional to the fluoride ion, polyatomic groups with strong electronic affinities can also form stable noble-gas containing anions of the type X-...NgO.

This paper discusses a significant public-private partnership (PPP) formed by the government and Taiwanese Farmer Associations. Particularly, it will investigate a pattern of the PPP that has successfully promoted rural development and agricultural modernization in Taiwan since 1950s. Taiwanese Farmer Associations (hereafter TFAs), similar to agricultural cooperatives in South Korea and Japan, have played a policy agent in fostering rural development in this island state since 1950s. TFA’s performance inherently came from Japanese Cooperatives before World War II. The Performances of those farmer organizations are combinations of economic, social, and educational synergies. The rural development experiences in Taiwan demonstrate that success of rural modernization is carried out by a special public-private partnership (PPP). First, this paper discusses formation and development of farmer cooperative organizations in East Asian societies and compare the similarities and differences of practice of those organizations and their relations to the governments among Taiwan, South Korea, and Japan. Secondly, this paper examines collaborative mold and process in which both the government and Taiwan Farmer Associations have been extensively involved. A specific cooperative apparatus between the government and TFA functioning and operating as a perfect PPP has been formed under administrative guidance of the state. Thirdly, this paper looks at input and various supports in financial and policy perspective by the public sector. Fourthly, the paper discusses legal framework, administrative apparatus, and governance pattern for TFA. Fifthly, the paper discuses that a specific PPP successfully involving in rural modernization in Taiwan is significantly derived from the state’ guidance that properly regulates a collaboration between the government and TFA. So-call East Asian model of PPP in agricultural modernization and rural community development may become a valuable experience for most of developing countries.

Typical modern information systems are required to process copious data. Conventional manual approaches can no longer effectively analyze such massive amounts of data, and thus humans resort to smart techniques and tools to complement human effort. Currently, network security events occur frequently, and generate abundant log and alert files. Processing such vast quantities of data particularly requires smart techniques. This study reviewed several crucial developments of existent data mining algorithms, including those that compile alerts generated by heterogeneous IDSs into scenarios and employ various HMMs to detect complex network attacks. Moreover, sequential pattern mining algorithms were examined to develop multi-step intrusion detection. These studies can focus on applying these algorithms in practical settings to effectively reduce the occurrence of false alerts. This article researched the application of data mining algorithms in network security. The academic community has recently generated numerous studies on this topic.

Scaffoldings play a critical role as temporary structures in supporting construction processes. Accidents at construction sites frequently stem from issues related to scaffoldings, including insufficient support caused by deviations from the construction design, insecure rod connections, or absence of cross bracing, which result in uneven loading and potential collapse, leading to casualties. In this study, we introduce a deep-learning-based, augmented reality (AR)-enabled system called scaffolding assembly deficiency detection system (SADDS) to assist field inspectors in identifying deficiencies in scaffolding assemblies. Inspectors have the flexibility to utilize SADDS through various devices, such as video cameras, mobile phones, or AR goggles (i.e., Microsoft HoloLens 2), for automated detection of deficiencies in scaffolding assemblies. The training test yielded satisfactory results, with a mean average precision of 0.89 and individual precision values of 0.96, 0.82, 0.90, and 0.89 for “qualified” frames and frames with the “missing cross-tie rod,” “missing lower-tie rod,” and “missing footboard” deficiencies, respectively. Field tests conducted at two construction sites demonstrated improved system performance compared to that in the training test. However, these field tests also revealed certain limitations of the SADDS system.

Introduction: Treating elbow fracture-dislocation is a challenge, especially in the situation of basal-coronoid trans-ulnar fracture. The study ams to explain whether or not the minimal invasive surgery (MIS) would be feasible in elbow dislocation with coronoid fracture. Materials & Methods: At Taipei Veterans General Hospital, patients who had elbow dislocations with coronoid process fractures underwent single one surgeon’s MIS techniques which included the fluoroscopy-guided ulnar anteromedial (FGUAM) approach in the stage of reducing coronoid process. When there is a proximal ulnar fracture, the posterior incision should be necessary, followed by the incision over the lateral or medial elbow in treating radial fractures or ligament injuries. Results: The Flow Diagram about approach recommendation was established in base of defining MIS as not to do cross-plane dissection. Anteriorly rigid fixation for the coronoid process was also emphasized. Conclusions: MIS can be achieved by multiple limited surgical incisions. However, if there is an unstable ulnar metaphysis or ligament avulsion fracture, the posterior approach has to be extended and the so-called MIS fails to be established.

Contaminants of Emerging Concern (CECs), a new category of contaminants in limelight, is a major issue of global concern. The pervasive nature of CECs and its harmful effects, such as cancer, reproductive disorders, neurotoxicity etc., make the situation alarming. The perilous nature of CECs lies in the fact that even very small concentration of CECs can cause great impacts on living beings. It also has a nature of bioaccumulation. Thus, it is the ultimate need to have efficient sensors for detection of CECs to ensure safe living environment. Electrochemical sensors are an efficient platform for CEC detection as they are highly selective, sensitive, stable, reproducible, and prompt, and can detect very low concentrations of analyte. Major classes of CECs are pharmaceuticals, illicit drugs, personal care products, endocrine disruptors, newly registered pesticides, and disinfection by-products. This review focusses on CECs, including their sources and pathways, health effects caused by them, and electrochemical sensors as reported in literatures under each category for the detection of major CECs.

GaN ultraviolet photodetector with metal-semiconductor-metal structure is achieved by growing on a periodic trapezoid column-shape patterned sapphire substrate using metalorganic chemical vapor deposition. Under 5-V reverse bias, the photodetector fabricated on such patterned sapphire substrate exhibits a lower dark current, a higher photocurrent, and a 476 % enhancement in the maximum responsivity as compare with those of the photodetector fabricated on conventional flat sapphire substrate. It is also found that the much larger UV-to-visible rejection ratio and the fact that responsivity drops in a smaller cut-off region are observed from photodetector fabricated by using a periodic trapezoid column-shape patterned sapphire substrate. These phenomena may all be attributed to the reduction of threading dislocation density and the improved quality of GaN film, as well as the internal reflection and/or scattering effect on the interface between GaN film and the periodic trapezoid column-shape pattern of the substrate.

A fluorescent probe, N'-((3-methyl-5-oxo-1-phenyl-4, 5-dihydro-1H-pyrazol-4-yl) methylene)-2-oxo-2H-chromene-3-carbohydrazide (MPMC), was synthesized and characterized. Characterizations of the synthetic MPMC were conducted by proton nuclear magnetic resonance (1HNMR) spectroscopy and carbon-13 nuclear magnetic resonance spectroscopy (13C NMR). The fluorescence emission behaviors of probe MPMC towards diverse metal ions were detected and the probe exhibited high sensitivity and selectivity towards Cu2+ over other metal ions via quenching of its fluorescence. Furthermore, the existence of other metal actions made no difference on the fluorescence intensity of the MPMC-Cu2+ system apparently, that is, MPMC displayed a good anti-interference ability. Job’s plot of MPMC and copper ions indicated the detection limit was 15.16 nM (R2=0.9612) for the assayed actions, with a stoichiometric ratio of 1:1 for MPMC and Cu2+. Additionally, the color of MPMC probe solution changed from nearly colorless to yellow in the presence of Cu2+ in visible light, which the color change could be observed by the naked eye. Similarly, the color resolved bright yellow into blue in ultraviolet light. Also reusability studies indicated that MPMC probe was reusable. The pH effect of probe MPMC to Cu2+ had a broad range of pH detection 4.0 to 11.0. The response time of MPMC probe for determining Cu2+ was within 1 min. The recognition of Cu2+ by MPMC performed on pre-treated paper under sunlight and UV light both had a distinct colour change. Thus, the solid-state method for detecting Cu2+ with the naked-eye, was both economical and convenient.

Applied talent is not only a builder of human civilization but also a promoter of economic development. They not only need systematic and solid engineering theoretical knowledge but also rich engineering practical experience. Applied undergraduate colleges are the cradle for cultivating applied talent and shoulder the important mission of cultivating various types of applied talent for society. With the rapid development of higher education, the number of applied undergraduate institutions has sharply increased, but the quality of applied talent cultivated by them has shown a significant decline, which greatly restricts the pace of industrial development in the world. This article proposes a new concept of promoting the "three certificates" (graduation certificate, degree certificate, and skill certificate) education model in applied undergraduate colleges, which is of great significance for the country to cultivate composite talents with the ability of "product design, production management, and product processing" at the same time.

How perceptual limits can be overcome has long been examined by psychologists. This study investigated whether visual cues, blindfolding, visual-auditory synesthetic experience and music training could facilitate a smaller frequency difference limen (FDL) in a gliding frequency discrimination test. It was hoped that the auditory limits could be overcome through visual facilitation, visual deprivation, involuntary cross-modal sensory experience or music practice. Ninety university students, with no visual or auditory impairment, were recruited for this one-between (blindfold/visual cue) and one-within (control/experimental session) designed study. A MATLAB program was prepared to test their FDL by an alternative forced-choice task (gliding upwards/gliding downwards/no change) and two questionnaires (Vividness of Mental Imagery Questionnaire & Projector-Associator Test) were used to assess their tendency to synesthesia. Participants with music training showed a significantly smaller FDL; on the other hand, being blindfolded, being provided with visual cues or having synesthetic experience before could not significantly reduce the FDL. However, the result showed a trend of reduced FDLs through blindfolding. This indicated that visual deprivation might slightly expand the limits in auditory perception. Overall, current study suggests that the inter-sensory perception can be enhanced through training but not though reallocating cognitive resources to certain modalities. Future studies are recommended to verify the effects of music practice on other perceptual limits.

Repetitive transcranial magnetic stimulation (rTMS) with intensive occupational therapy improves upper limb motor paralysis and activities of daily living after stroke; however, amount of improvement according to paralysis severity remains unverified. Target activities for daily living using patients’ upper limb functions can be established by predicting the amount of change after treatment for each severity level of upper limb motor paralysis and further aid practice planning. This study estimated post-treatment score changes for each severity level of motor paralysis (no, poor, limited, notable, and full) stratified according to Action Research Arm Test (ARAT) scores before combined rTMS and intensive occupational therapy. Severity of motor paralysis was the fixed factor for analysis of covariance, delta (post-pre) of the scores was the dependent variable. Ordinal logistic regression analysis was used to compare changes in ARAT subscores in patients, divided according to paralysis severity before treatment. A multicenter retrospective cohort dataset analyzed 907 patients with stroke hemiplegia. Largest treatment-related changes in scores were observed in the Limited recovery group for upper limb motor paralysis and Full recovery group for quality-of-life activities using paralyzed upper limb. These results will help predict treatment effects and determine exercises and goal movements for occupational therapy after rTMS.

Heavy metals contamination in groundwater often occurs in various industrial processes. Stud-ies have confirmed that polysulfide could reduce hexavalent chromium to trivalent chromium, achieving the effect of in-situ stabilization. For other heavy metals contamination in groundwa-ter, whether polysulfide also had a stabilizing ability to achieve in-situ remediation. This re-search focused on heavy metals except for chromium that often contaminated in groundwater, including lead, nickel, zinc, copper, and cadmium to explore the feasibility of using calcium polysulfide (CaSx) as an in-situ stabilization technology for these heavy metals contamination groundwater. Results showed that CaSx had a great removal efficiency for heavy metals lead, nickel, zinc, copper, and cadmium. However, for nickel, zinc, copper and cadmium, when CaSx was added excessively, complexes would be formed, causing the result of re-dissolve and this would also reduce the removal efficiency. Since it is difficult to accurately control the dosage of agents for in-situ groundwater remediation, the concentration of re-dissolved nickel, zinc, cop-per, and cadmium may not be able to meet the groundwater control standards. CaSx had high lead removal efficiency, and it would not cause re-dissolution due to excessive CaSx dosing. CaSx can be used as an in-situ stabilization technique for lead contaminated groundwater.

In order to study the effect of explosion load on the flexural performance of RC beams, two RC beams of the same size were carried out explosion test and bearing capacity test successively. Piezoelectric intelligent aggregate was embedded in the beams in advance to monitor the damage state of the beams, which realized the whole process of damage monitoring of the concrete inside the structure from explosion damage to compression damage.Based on wavelet packet analysis and residual bearing capacity damage evaluation criteria, the beam damage was quantitatively evaluated, and the bending bearing capacity of RC beam after explosion damage was compared and analyzed.The results show that the change of concrete strain gauge signal, the phenomenon of crack development and the increase of internal crack development index indicate that the RC beam is damaged by explosion load.After explosion damage, the damage index of the beam increases and the residual bending capacity decreases, which proves that the piezoelectric intelligent aggregate sensor can effectively monitor the bending capacity change of the component after explosion damage.

Taiwan's bed and breakfast (B&B) development has been more than 25 years ago, from the first generation of retirement to the B&B industry, serving tourists from all over the world accom-modation, providing breakfast and accommodation mode to the present, after the change of employees from the second generation, more and more attention is paid to the cultivation and cultivation of business ability. With the advent of the era of AI technology networking, the ca-pabilities required for B&B operation are more focused on all aspects of service, and the good marketing ability of B&B can promote a green chimney-free tourism economy, which is also a favorite industry of various governments and the public. This study explores the basic vocational competency indicators required for running a B&B, with (1)EQ emotion management skills, (2)Financial management ability, (3)(SK) technical skills, and (4)Marketing and promotion management capabilities. Through the study method, the K-S Z test was determined by the con-sensus conclusion of expert reliability and validity p value

There always exist steel cuttings, holes and cracks at the interfaces in the explosive composite plate. Multi-pass friction stir processing (M-FSP) is proposed in this research to optimize the interface microstructure and the interface connection for 1060Al/Q235 explosive composite plate. Results show that the microstructures of 1060Al after M-FSP are fine and uniform owing to the strong stirring effect and recrystallization. Micro-defects formed by the explosive welding can be repaired by the M-FSP. However, M-FSP can also form tunnel defects in the aluminum, especially when the passes are one and two. The melting block and the melting lump in the composite plates are easy to become source of crack. The shear strengths and the bending properties for the 1060Al/Q235 explosive composite plate after M-FSP are the best when the passes are three, with the tool rotation speed of 1200rpm and the forward speed of 60mm/min. The optimized interfaces for the explosive composite plate after M-FSP are mainly by the metallurgical bondings, with a certain thickness and are discontinuous. Therefore, the crack extension stress is the largest and the mechanical properties are the best.

The sustainable development of resource-based cities has long been a focal point for both governmental policies and academic research. A wealth of academic literature identifies the 'resource curse' as a critical barrier to sustainable development in these urban areas. Despite extensive studies, a consensus on effective strategies to circumvent or resolve this challenge remains elusive. Recent empirical data reveals a noticeable pattern of economic growth differentiation in China's resource-based cities. Why do some resource-based cities experience economic decline while others achieve sustainable economic growth? Therefore, this paper analyzes the reasons for the divergence of economic growth in resource cities from the perspective of heterogeneity. The results of the study show that the phenomenon of the resource curse is conditional, and the heterogeneity of demo-graphic changes, geographic location and institutional environment has a significant impact on the economic growth of resource cities. These factors are investigated to elucidate the observed diversification and heterogeneity in the economic growth of resource-based cities. Building upon this analysis, the paper proposes a framework for differentiated sustainable development pathways tailored to the unique contexts of these cities. This approach not only contributes to the current understanding of the 'resource curse' but also offers novel insights for future research aiming to adopt a more nuanced and context-specific perspective in examining sustainable urban development.

3D reality capturing has demonstrated increased efficiency and consistently accurate outcomes in architectural digitisation. Nevertheless, despite advancements in data collecting, 3D reality capturing still lacks full automation, especially in the post-processing and modelling phase. Artificial intelligence (AI) has been a significant focus, especially in computer vision, and tasks such as image classification and object recognition might be beneficial to the digitisation process and its subsequent utilisation. This article aims to examine the potential outcomes of integrating AI technology into the field of 3D reality-capturing, with a particular focus on its use in architectural scenarios. The main methods used for data collection are laser scanning (static or mobile) and photogrammetry. As a result, image data including RGB-D data (files containing both RGB colours and Depth information) and point clouds have become the most common raw datasets available for object mapping. The study comprehensively analyses the current use of 2D and 3D deep learning techniques in documentation tasks, particularly downstream applications. It also highlights the ongoing research efforts in developing real-time applications with the ultimate objective of achieving generalisation and improved accuracy.

In the rapidly evolving landscape of genetic engineering, the advent of CRISPR-Cas technologies has catalyzed a paradigm shift, empowering scientists to manipulate the genetic code with unprece-dented accuracy and efficiency. Despite the remarkable capabilities inherent to CRISPR-Cas sys-tems, recent advancements have witnessed the integration of small molecule to augment their functionality, introducing new dimensions to the precision and versatility of gene editing applica-tions. This review delves into the synergy between CRISPR-Cas technologies and small molecule drugs, elucidating the pivotal role of chemicals in optimizing target specificity and editing efficiency. By examining a diverse array of applications, ranging from therapeutic interventions to agricultural advancements, we explore how the judicious use of chemicals enhances the precision of CRISPR-Cas-mediated genetic modifications. In this review we emphasize the significance of small molecule drugs in fine-tuning the CRISPR-Cas machinery, which allows researchers to exert meticulous con-trol over the editing process. We delve into the mechanisms through which these chemicals bolster target specificity, mitigate off-target effects, and contribute to the overall refinement of gene edit-ing outcomes. Additionally, we discuss the potential of chemical integration in expanding the scope of CRISPR-Cas technologies, enabling tailored solutions for diverse genetic manipulation challenges. As CRISPR-Cas technologies continue to evolve, the integration of small molecule drugs emerges as a crucial avenue for advancing the precision and applicability of gene editing techniques. This re-view not only synthesizes current knowledge but also highlights future prospects, paving the way for a deeper understanding of the synergistic interplay between CRISPR-Cas systems and chemical modulators in the pursuit of more controlled and efficient genetic modifications.

With the development of remote sensing satellite technology for Earth observation, remote sensing stereo images have been used for three-dimensional reconstruction in various fields, such as urban planning and construction. However, remote sensing images often include noise, occluded regions, weakly textured areas and repeated textures, which can lead to reduced accuracy in stereo matching and affect the quality of the 3D reconstruction results. To reduce the impact of complex scenes in remote sensing images on stereo matching and to ensure both speed and accuracy, we propose a new end-to-end stereo matching network based on convolutional neural networks (CNNs). The proposed stereo matching network can learn features at different scales from the original images and construct cost volumes with varying scales to obtain richer scale information. Additionally, when constructing the cost volume, we introduce negative disparity to adapt to the common occurrence of both negative and nonnegative disparities in remote sensing stereo image pairs. For cost aggregation, we employ a 3D convolution-based encoder-decoder structure that allows the network to adaptively aggregate information. Before feature aggregation, we also introduce an attention module to retain more valuable feature information, enhance feature representation, and obtain a higher-quality disparity map. By training on the publicly available US3D dataset, we obtain the accuracy that 1.115 pixel in end-point error (EPE) and 5.32% in the error pixel ratio (D1) on the test dataset, and the inference speed is 92 ms. Comparing our model with existing state-of-the-art models, we achieve higher accuracy, and the network is beneficial for the three-dimensional reconstruction of remote sensing images.

AI advances integrate generative design tools in architecture, providing architects with sophisticated design options. It enables the creation of intricate, high-performing projects by exploring diverse design possibilities with AI and algorithms. Generative AI and generative design empower architects to create better-performing, sustainable, and efficient design solutions and explore diverse design possibilities. This paper leverages multimodal generative AI to enhance design creativity by combining textual and visual inputs. Blockchain technology converts design metadata into NFTs, ensuring secure, authentic, and traceable data storage. The framework addresses data ownership, legal adherence, and client-architect collaboration and is entirely scalable for digital design authentication. This research exemplifies the pragmatic fusion of Generative AI and blockchain technology applied in architectural design for more transparent, secure, and effective results. This study provides a strategy that uses generative AI technologies to achieve an efficient and creative workflow in the early stages of architectural design.

In the TANGO study, the long-term noninferior efficacy of switching to dolutegravir/lamivudine (DTG/3TC) compared to continuing tenofovir alafenamide–based regimens was demonstrated in treatment-experienced adults with HIV. However, there is limited real-world data comparing the effectiveness and safety of bictegravir/emtricitabine/tenofovir alafenamide fumarate (BIC/FTC/TAF) and DTG/3TC in Asia. This retrospective observational study, conducted at a designated HIV-care hospital from March 2019 to January 2023, aimed to address this gap. Demographic, clinical, and laboratory data, including HIV viral loads and lipid profiles, were collected and analyzed. The primary outcome was the proportion of patients with HIV RNA <50 copies/mL at week 48 in both groups, utilizing a snapshot, per-protocol–exposed population. A total of 1086 patients were included, with 511 in the DTG/3TC group and 575 in the BIC/FTC/TAF group. At week 48, 98% of patients in the DTG/3TC group and 94% in the BIC/FTC/TAF group achieved HIV RNA <50 copies/mL (p <0.01). Logistic regression analysis identified risk factors for detectable viral loads at week 48, including HIV RNA >100,000 copies/mL (AOR 5.13, 95% CI 1.42–18.53), low-level viremia (AOR 3.91, 95% CI 1.07–14.25), and record of virologic failure ≥2 times (AOR 4.21, 95% CI 1.64–10.85) before the switch. Furthermore, no significant difference was found between the DTG/3TC and BIC/FTC/TAF regimens (AOR: 1.51, 95% CI 0.70–3.24). In conclusion, the study demonstrates that the effectiveness and safety profiles of DTG/3TC and BIC/FTC/TAF were comparable in treatment-experienced adults with HIV, particularly among those with undetectable viral loads at baseline.

Tremor is a prevalent neurological disorder characterized by involuntary shaking or trembling of body parts. This condition impairs fine motor skills and hand coordination to varying degrees and can even affect overall body mobility. As a result, tremors severely disrupt the daily lives and work of those affected, significantly limiting their physical activity space. This study developed an innovative Spatial Augmented Reality (SAR) system aimed at assisting individuals with tremor disorders to overcome their physical limitations and expand their range of activities. The system integrates eye-tracking and Internet of Things (IoT) technologies, enabling users to smoothly control objects in the real world through eye movements. It employs a virtual stabilization algorithm for stable interaction with objects in the real environment. The study comprehensively evaluated the system's performance through three experiments: 1) assessing the effectiveness of the virtual stabilization algorithm in enhancing the system's ability to assist individuals with tremors in stable and efficient interaction with remote objects; 2) evaluating the system's fluidity and stability in performing complex interactive tasks; 3) investigating the precision and efficiency of the system in remote interactions within complex physical environments. The results demonstrate that the system significantly improves the stability and efficiency of interactions between individuals with tremor and remote objects, reduces operational errors, and enhances the accuracy and communication efficiency of interactions.

Ganoderic Acid (GA), a major bioactive compound isolated from an oriental medicinal mushroom, i.e. Ganoderma tsugae, has traditionally been found to have significant medicinal properties. As a result of GA's poor solubility in water, formulation poses several challenges. Additionally, the traditional method of administering it via alcohol always results in unfavorable patient side effects. In order to overcome these problems, Ganoderma Tsugae extracts obtained by ethanol extraction were encapsulated in nanodispersions by ultrasonic cavitation and solvent evaporation to maximise bioavailability. Resultant nanodispersions contained Ganoderic acid in a hydrophobic core with a mean particle size of no more than 200 nm and a very narrow particle distribution. An analysis of the interactions between the control variables and the process optimisation was conducted using the Response Surface Methodology (RSM). Based on the results of the experiment, it was found that the particle size of nanodispersions was influenced by the Hydrophilic-Lipophilic Balance (HLB) number and the evaporation temperature. Moreover, the physical stability of micellar systems is generally determined by the organic phase within them. Regarding formulation stability, the zeta average of the nanodispersions remained virtually unchanged in solutions with different pH levels and short-term storage (14 days) at room temperature. Overall, it has been demonstrated that Ganoderic acid nanodispersions can be efficiently generated by combining ultrasound cavitation and solvent evaporation.

This paper presents a comprehensive study on the application and optimization of automotive thermoelectric generators (ATEGs), focusing on the crucial role of heat exchangers in enhancing energy conversion efficiency. Recognizing the substantial waste of thermal energy in internal combustion engines, our research delves into the potential of TEGs to convert engine waste heat into electrical energy, thereby improving fuel efficiency and reducing environmental impact. We meticulously analyze various heat exchanger designs, assessing their influence on the TEG's output power under different exhaust gas flow rates and temperatures. Furthermore, we explore the impact of TEG material properties on the overall energy conversion effectiveness. Our findings reveal that specific heat exchanger designs significantly enhance the efficiency of waste gas heat exchange, leading to an improved performance of the TEG system. We also highlight the importance of thermal insulation in maximizing TEG output. This study not only contributes to the ongoing efforts to develop more sustainable and efficient vehicles but also provides valuable insights into the practical application of thermoelectric technology in automotive engineering. Through this research, we aim to pave the way for more environmentally friendly transportation solutions, aligning with global efforts to reduce fossil fuel dependence and mitigate environmental pollution.

. Manufacturers are increasingly adopting mixed-flow manufacturing models to meet the growing customized, diverse, and dynamic customer demand. In such an environment, material distribution scheduling optimization is vital for smooth operations and is integral to production management. However, manufacturers frequently encounter problems like disordered and delayed material distribution. Traditional scheduling methods suffer from problems like inadequate transparency, delayed decision directives, and suboptimal results, impacting performance. To this end, this study proposes a dynamic material distribution scheduling optimization model and strategy based on digital twin (DT) to address these problems. Firstly, we introduce workstation satisfaction and establish a material distribution path optimization model minimizing total distribution cost while maximizing workstation satisfaction. Subsequently, we present a cloud-edge computing-based decision framework and explain the DT-based material distribution system's components and operation. Furthermore, a dynamic material distribution scheduling optimization mechanism based on DT is designed. By incorporating a savings method and incentive, penalty strategies, improvements are made to the path node selection probabilities and the information pheromone update rules of the traditional ant colony optimization (ACO) algorithm. Finally, a numerical case study, using real data from collaborating enterprises, validates the proposed algorithm and strategy. This research offers valuable insights into logistics management and algorithm design in smart manufacturing environments.

Due to the fact that abrasive media can deform flexibly in abrasive flow machining (AFM) making this method easily to polish the complex holes and the curved surface of the hard machining shapes. Although abrasive media dominate the polishing behavior in AFM process, the mechanism of the abrasive media are not easy to understand because of the high viscous gels, therefore, many finishing works need lots of time to design AFM process. Power laws of the abrasive gels is studied here to evaluate the non-Newtonian flow of abrasive gels in complex holes polishing firstly, at the mean time different abrasive gels are utilized to finish the complex holes to follow the results by non-Newtonian flow calculation. Moreover, traditional AFM has difficulty to achieve a uniform roughness of radial distribution in the complex holes polishing because of the non-uniform abrasive forces. So a helical passageway is proposed to create a multiple motion of abrasive medium and to obtain the even surface of the complex holes in AFM process.

Floating Offshore Wind Turbine (FOWT) is an innovative technology with little industry guidance for its hull design. Various FOWT floaters with different hull shapes claim to support the same turbines. Structural integrity and material expense analyses of different pontoon shapes were conducted, and it was found that some configurations, such as those with every two columns connected by both pontoon and bracing, have advantages over others. However, it is important to note that the choice of pontoon shape should be based on the wave loading conditions the floater will be exposed to. While a T-shaped pontoon provides a cost-effective solution under certain wave loading scenarios, it may not be the best option for all conditions. Specifically, ring pontoon designs with full bracing were found to be necessary for withstanding certain wave loads. Therefore, it is important to consider different Dominant Load Parameters (DLP) and ensure that a FOWT floater can withstand all applicable DLPs. An uneven hexahedral column shape, which combines the best attributes of square and round shapes, is proposed as a better alternative to cylindrical columns. It offers ease of manufacture and reasonably low drag. Bracing is found to be necessary for withstanding the wind turbine’s incurred moment and forces. The conclusion is that platform design should prioritize manufacturing costs and strength over maximizing hydrodynamic performance.

Global warming poses a threat to plant survival, impacting growth and agricultural yield. Protein turnover, a critical regulatory mechanism balancing protein synthesis and degradation, is crucial for cellular response to environmental changes. We investigated the effects of elevated temperature on proteome dynamics in Arabidopsis thaliana seedlings using 15N-stable isotope labeling and ul-tra-performance liquid chromatography-high resolution mass spectrometry, coupled with the ProteinTurnover algorithm. Analyzing different cellular fractions from plants grown under 22°C and 30°C growth conditions, we found significant changes in the turnover rates of 571 proteins, with a median 1.4-fold increase, indicating accelerated protein dynamics under thermal stress. Notably, soluble root fraction proteins exhibited smaller turnover changes, suggesting tissue-specific adap-tations. Significant turnover alterations occurred with redox signaling, stress response, protein folding, secondary metabolism, and photorespiration, indicating complex responses enhancing plant thermal resilience. Conversely, proteins involved in carbohydrate metabolism and mito-chondrial ATP synthesis showed minimal changes, highlighting their stability. This analysis high-lights the intricate balance between proteome stability and adaptability, advancing our under-standing of plant responses to heat stress and supporting the development of improved thermo-tolerant crops.

Glaucoma is one of the primary causes of blindness worldwide. Canal opening surgery, a type of minimally invasive glaucoma surgery (MIGS) applied in cases of mild to moderate glaucoma, has gained increasing popularity in recent years due to its efficacy in reducing intraocular pressure, its safety profile, the simplicity of its technique, and the reduced likelihood of compromised vision. Nevertheless, the existing body of histopathological studies remains insufficient for a comprehensive understanding of post-surgical wound healing. Consequently, debates persist among researchers regarding the mechanism through which Schlemm’s canal opening surgery reduces intraocular pressure, as well as the surgical techniques that may impact the outcomes and the factors influencing surgical success. As the history of MIGS is relatively short and lacks sufficient systemic reviews or meta-analysis evaluating the influence of individual factors, this review was conducted to illuminate disparities in the researchers’ opinions at the current stage of research.

For orthopaedic applications, additive manufactured (AM) porous scaffolds made of absorbable metals like magnesium, zinc or iron are of particular interest. They do not only offer the potential to design and fabricate bio-mimetic or rather bone equivalent mechanical properties, they also do not need to be removed in further surgery. Located in a physiological environment, scaffolds made of absorbable metals show a decreasing Young’s modulus over time, due to product dissolution. For WE43 scaffolds, during the first days an increase of the smeared Young's modulus can be observed, which is mainly attributed to a forming substrate layer of degradation products on the struts surfaces. In this study the influence of degradation products on the stiffness properties of metallic scaffolds is investigated. For this, analytical calculations and finite element simulations are performed to study the influence of the substrate layer thickness and Young's modulus for single struts and for a new scaffold geometry with adapted polar f2cc,z unit cells. The finite element model is further validated by compression tests on AM scaffolds made from Zn1Mg. The results show, that even low thicknesses and Young's moduli of the substrate layer increases significantly the smeared Young's modulus under axial compression.

We quantitatively investigated the statistical behaviors of semiflexible polymer chains, which are simultaneously subjected to force stretching and rectangular tube confinement. Based on the wormlike chain model and Odijk deflection theory, we derived a new deflection length, by which new compact formulas are obtained for the confinement free energy and force-confinement-extension relation. These newly derived formulas have been justified by numerical solutions of an eigenvalue problem associated with the Fokker-Planck governing equation and extensive Brownian dynamics simulations based on the so-called Generalized Bead-Rod (GBR) model. We found that, comparing to the classical deflection theory, these new formulas are valid for a much extended range of the confinement-size /persistence-length ratio, and have no adjustable fitting parameters for sufficient long semiflexible chains in the whole deflection regime.

Session-based recommendations which aim to predict subsequent user-item interaction based on historical user behavior during anonymous sessions can be challenging tasks. Two main challenges need to be addressed and improved: (1) How to analyze these sessions to accurately and completely capture users’ preferences, and (2) how to identify and eliminate any interference caused by noisy behavior. Existing methods have not adequately addressed these issues since they either neglected the valuable insight that can be gained from analyzing consecutive groups of items or failed to take these noisy data in sessions seriously and handled them properly, which can jointly impede recommendation systems from capturing users’ real intentions. To address these two problems, we designed a multi-order semantic denoising (MSD) model for session-based recommendations. Specifically, we grouped items of different lengths as varying multi-order semantic units to mine the user’s primary intention from multiple dimensions. Meanwhile, a novel denoising network was designed to alleviate the interference of noisy behavior and provide a more precise session representation. The result of extensive experiments on three real-world datasets demonstrated that the proposed MSD model exhibited improved performance compared with existing state-of-the-art methods in session-based recommendation.

A typical vibrational spectrum in the ice phase has four separate bands: translation, libration, bending and stretching. Ice X, the final ice phase under high pressure, shows an exotic vibrational spectrum. Theoretically, an ideal crystal of ice X only has one peak at 998 cm-1 for Raman scattering and two peaks at 450 cm-1 and 1507 cm-1 for infrared absorption in this work. These three characteristic peaks are indicators of the phase transition between ice VII/VIII and ice X. Despite much experimental and theoretical work on ice X, only this study has clearly indicated these characteristic peaks in the region of the IR band. The phonon density of states shows quite different features than ice VIII, which could be verified by inelastic neutron scattering in the future. The dynamic processes of 15 vibrational normal modes are discussed and the typical hydrogen bonds are missing.

The integration of robotic devices into healthcare settings for rehabilitation purposes represents a rapidly advancing field with significant benefits for both therapists and patients. However, standalone robot systems face limitations such as inefficient processing of patient data and logistical challenges for patients, such as travel time to rehabilitation centers. To address these shortcomings, this paper proposes the integration of cyber-physical systems into rehabilitation robotics. Cyber-physical systems leverage network connectivity and real-time data processing to enhance the efficiency and convenience of robot-based rehabilitation. By seamlessly integrating sensors, actuators, and computational algorithms, cyber-physical rehabilitation systems empower therapists to more effectively treat patients by providing actionable insights derived from comprehensive data analysis. This enables therapists to tailor treatment plans precisely to each patient’s unique needs, ultimately leading to improved outcomes. Additionally, cyber-physical rehabilitation systems facilitate remote monitoring and intervention, allowing therapists to oversee patient progress and make timely adjustments to treatment protocols without the need for in-person visits. This not only saves patients valuable time and resources but also ensures continuity of care, particularly for individuals residing in remote or underserved areas. Furthermore, cyber-physical rehabilitation systems enable collaborative decision-making by facilitating communication and information sharing among healthcare professionals, further enhancing the quality and efficacy of rehabilitation services. In summary, integrating cyber-physical systems into rehabilitation robotics represents a significant advancement in leveraging technology to optimize patient care and outcomes, promising to revolutionize rehabilitation therapy.

Chinese Taihe Black-bone silky fowl (TBsf) is the homology of medicine and food and has high nutritional and medical value all over the world. However, the nutritional compositions and specific metabolite advantages of Taihe silky fowl muscle are still poorly understood. In this study, we investigated the differences of nutritional components between TBsf and another similar breed (Black Feathered chicken and laid green-shelled eggs, BF-gsc). Meanwhile, we also explored the divergences in muscle characteristics of Taihe silky fowl fed with two different diets, that is normal chicken feed (TBsf-ncf) and Broussonetia papyrifera-fermented feed (TBsf-bpf). Firstly, the growth performance and biochemical index of Taihe silky fowl was significantly different compared with black-feathered chicken. Secondly, we identified the metabolic alterations in Taihe silky fowl by performing an un-targeted UHPLC-Q-TOF-MS/MS analysis. Our results suggested that the whole metabonomic characteristics had obvious separation between TBsf-ncf, TBsf-bpf and BF-gsc groups both in the positive and negative ion mode by PCA analysis. Next, OPLS-DA multivariate analysis revealed that 57 metabolites (in positive mode) and 49 metabolites (in negative mode) were identified as differential metabolites between TBsf-ncf and BF-gsc group. These differential metabolites were mainly enriched to ABC transporters, biosynthesis of amino acids and aminoacyl-tRNA biosynthesis. Besides, there were 47 metabolites (in positive) and 13 metabolites (in negative) were differentially regulated between TBsf-ncf and TBsf-bpf group, which were majorly involved in histidine metabolism and linoleic metabolism. Furthermore, the integrated network analysis suggested that DL-arginine, DL-isoleucine, linoleoylcarnitine, stearoylcarnitine (positive) and ricionleic acid, D-proline, uric acid (negative) were the significantly metabolic biomarkers in Taihe silky fowl. Moreover, the metabolites of primaquine, ticlpoidine, riboflavin, acetylcarnitine (positive) and salicylic acid, acetaminophen sulfate, glutamic acid (negative) were markedly changed in the Taihe silky fowl fed with BP-fermented feed. In summary, a global survey of the nutritional components and metabolite differences were performed in muscle tissues of Taihe silky fowl between various breeds and feeds. The comprehensive expression profiles of the metabolites in Taihe silky fowl affected by genetic and environmental factors were acquired. This study provided valuable evidence fo breed and feed-induced putative biomarkers as well as improved the economic value of Taihe silky fowl through targeted metabolite regulation.

Disassembly is a pivotal technology to enable the circularity of electric vehicle batteries by applying circular economy strategies that extend the life cycle of their components, like remanufacturing and repurposing, or by using efficient recycling to reintegrate the gained materials in producing new battery systems. This paper aims to develop a multi-method self-configuring simulation model for investigating disassembly scenarios while considering the battery design as well as the configuration and layout of the disassembly station. We demonstrate the developed model in a case study using a battery of Mercedes-Benz and the automated disassembly station of the project DeMoBat at Fraunhofer IPA. Furthermore, we introduce two disassembly scenarios, the component-oriented and the accessibility-oriented disassembly, and compare them using the simulation model to determine several indicators, such as the frequency of tool change, the number and distribution of robot routes, the tool utilization, and the disassembly time.

Spectrally weighed irradiance on the corneal plane is often used to determine the visual and non-visual potency of light. Spectral irradiance or illuminance is measured with a diffuser in the so-called 2π geometry (i.e., a hemispheric measurement). Due to anatomical conditions, the human binocular field of view (FOV) does not correspond to a hemisphere but is occluded upwards and downwards. FOV-restricted measurements are scarce, however, and thus the error when using hemispheric measurements is yet to be determined. For our study, we designed and 3D printed FOV occlusions as attachments to spectral measurement devices. Measurements with and without the occlusion were taken in different lighting situations in the laboratory (light from different directions) and in real-world conditions (light typically from above). Our measurements show a reduction of visual and melanopic values due to the FOV occlusion ranging from negligible to over 60% for realistic scenarios. Further, the reduction was comparable for visual and melanopic parameters, as the distribution of light in the FOV was generally spectrally homogeneous. In the case of an exemplary and artificial laboratory situation, however, the melanopic daylight (D65) efficacy ratio changed by more than a factor of 2 only due to the FOV occlusion. Finally, head orientation showed a marked impact on all quantities. Our results reveal the potential for considerable error when just evaluating and comparing vertical, hemispheric measurements in experiments and non-visual lighting design projects. We thus encourage the (additional) use of a FOV occlusion for eye-level measurements in typical viewing directions and provide open-source 3D-print files.

An active power dispatch method for a microgrid (MG) with multi-type loads, renewable energy sources (RESs) and distributed energy storage devices (DESDs) is the focus of this paper. The MG operates in a grid-connected model, and distributed power sources contribute to the service for load demands. The outputs of multiple DESDs are controlled to optimize the active power dispatch. Our goal with optimization is to reduce the economic cost under time-of-use (TOU) price, and to adjust the excessively high or low load rate of distributed transformers (DTs) caused by the peak-valley demand and load uncertainties. To simulate a practical environment, the stochastic characteristics of multi-type loads are formulated. The transition matrix of system state is provided. Then, a finite-horizon Markov decision process (FHMDP) model is established to describe the dispatch optimization problem. A learning-based technique is adopted to search the optimal joint control policy of multiple DESDs. Finally, simulation experiments are performed to validate the effectiveness of the proposed method, and the fuzzification analysis of the method is presented.

In this paper, a novel voltage control strategy of stand-alone operation brushless doubly fed induction generator for variable speed constant frequency wind energy conversion systems was presented and discussed particularly. Based on the model of the generator power system, the proposed direct flux control strategy employs a nonlinear reduced-order generalized integrator based resonant sliding-mode control scheme to directly calculate and regulated the output value of converter which control winding stator required so as to eliminate the instantaneous errors of power winding stator flux, and no involving any synchronous rotating coordinate transformations. The stability, robustness and convergence capability of the proposed control strategy were described and analyzed. Owing to no extra current control loops involved, therefore simplifying the system configuration design and enhancing the transient performance. Constant converter switching frequency was achieved by using space vector pulse width modulation, which reduce the harmonic of generator terminal voltage. In addition, experimental results prove the feasibility and validity of the proposed scheme, and excellent steady and dynamic state performance is achieved.

Oil-Gan, also known as emblica, is the fruit of the genus Phyllanthus emblica L. The fruits of these trees are high in nutrients and have excellent effects on health care and development values. There are many methods for the management of diabetic nephropathy (DN). However, there is a lack of effective drugs for treating DN from throughout the disease course. The primary aim of this study was to examine the protective effects (including urine analyses, the measurement of inflammatory cytokine levels, and histological examination) and mechanisms of action of an ethyl acetate extract of P. emblica (EPE) on db/db mice, an animal model of diabetic nephropathy, as well as a secondary aim of examining the expression levels of protein kinase Cα (PKCα) in the kidney and its downregulation of vascular endothelial growth factor (VEGF) and fibrosis gene transforming growth factor-β1 (TGF-β1) by Western blot analyses. Eight db/m C57BLKS/J mice were used as the control group. Forty db/db mice were randomly divided into five groups. Treatments included vehicle, EPE1, EPE2, EPE3 (at doses of 100, 200, or 400 mg/kg EPE), or the comparative drug aminoguanidine for 8 weeks. After 8 weeks of treatment, blood samples were collected for analyses of blood glucose, insulin, and HbA1c levels, and pancreatic and kidney tissues were dissected for histological analyses. The present study indicated that the administration of EPE to db/db mice effectively controlled hyperglycemia and hyperinsulinemia by markedly lowering blood glucose, insulin, and glycosylated HbA1c levels. Administration of EPE to db/db mice decreased the levels of BUN and creatinine both in blood and urine and reduced urinary albumin excretion and the albumin creatine ratio (UACR) in urine. Moreover, EPE treatment decreased the blood levels of inflammatory cytokines, including kidney injury molecule-1 (KIM-1), C-reactive protein (CRP), and NLR family pyrin domain containing (NLRP3). Our findings showed that EPE not only had antihyperglycemic effects but also improved renal function in db/db mice. Histological examination of the kidney by immunohistochemistry indicated that EPE can improve kidney function by ameliorating glomerular morphological damage following glomerular injury; alleviating proteinuria by upregulating the expression of nephrin, a biomarker of early glomerular damage; and inhibiting glomerular expansion and tubular fibrosis. Moreover, the administration of EPE to db/db mice increased the expression levels of p- PKCα/t-PKCα but decreased the expression levels of VEGF and renal fibrosis biomarkers (TGF-β1, collagen IV, p-Smad2, p-Smad3, and Smad4), as shown by Western blot analyses. These results implied that EPE as a supplement has a protective effect against renal dysfunction through the amelioration of insulin resistance as well as the suppression of nephritis and fibrosis in a DN model.

Questions：SAP in mountainous cities of China serve as crucial carriers for species and wild food, constituting potential green infrastructure. These patches should be recognized as locally specific resources. This study investigates the transformation characteristics of the landscape patterns of SAP, along with their elements, across urban-rural gradients, providing foundational support for the planning of conservation and utilization strategies. Location: Yongchuan area of Chongqing in southwest China. Methods: The study investigated urban-rural gradient-based transformation of SAP. A four-direction transect space was selected and divided into uniform sample squares. Fragstats 4.3 calculated the landscape index of SAP, and Spearman correlation coefficients in SPSS were used to evaluate the influence of landform and artificial factors on agroforestry patch transformation. Results: 1) Patch area (PA), Plaque density (PD), and CLUMPY of SAP systematically transform, showing increased SAP areas and higher connectivity with greater distance from the city, resulting in reduced patch fragmentation. However, Edge density (ED) and Largest plaque index (LPI) exhibit irregular transformation patterns. 2) With increased distance from the city, woodland patch area and connectivity increase, leading to decreased fragmentation, dispersal, and lower fractal dimensions. Conversely, Cultivated land follows the opposite trend. garden land patch area, fractal dimension, fragmentation, and dispersal all increase, while connectivity decreases. 3) Landscape pattern transformations of SPA are significantly influenced by artificial factors. Woodland patches are influenced similarly by landform and artificial factors. In contrast, cultivated land and garden land patches are more significantly impacted by artificial factors. Conclusions: SAP exhibit differentiated conservation and utilization measures across urban-rural gradients. Small patches located far from urban centers may benefit from systematic conservation measures to prevent further fragmentation and erosion in peri-urban areas.

To decrease privacy risks, consumers may choose to misrepresent when they are asked to offer personal information. This paper examines the impact of consumer misrepresentation on a monopolistic firm and consumers with an economic model. The results show that consumer misrepresentation may benefit the firm but hurt consumers. In addition, consumers misrepresentation may encourage the firm to provide higher personalized service level in certain scenarios, such as, when the unit cost of personalized service is low. Thirdly, when consumers misrepresent, and the firm only covers part of the market, a greater unit value of consumer’s privacy information will reduce the firm’s profit, but a greater unit cost of personalized service increases the firm’s profit.

Purpose: We evaluated the outcomes of fluid-gas exchange (FGE) for long-term flap closure of idiopathic macular hole (MH) after the inverted internal limiting (ILM) flap technique. Methods: We included eyes showed flap closure without complete MH closure, connection of the apart macular tissue, 1 month postoperatively after the inverted ILM flap technique. The eyes stayed at flap closure at 2 months postoperatively further underwent in-office FGE with 16% C3F8. Results: Among 10 eyes, 5 eyes (50%) showed flap closure at 2 months postoperatively further underwent FGE for complete MH closure while the remaining 5 eyes (50%) progressed directly at 2 months postoperatively. The improvement in vision of all flap closure from baseline was significant (p=0.015), with the mean baseline vision was 1.19 [Snellen equivalent (SE), 20/307] ± 0.52 logMAR and the mean final vision being 0.63 (SE, 20/85) ± 0.38 logMAR. The group that underwent FGE showed a better final vision of 0.45 (SE, 20/75) ± 0.23 logMAR than the group that didn’t undergo FGE (0.81 [SE, 20/128] ±0.44 logMAR). All eyes achieved complete MH closure, including the eyes that underwent FGE in a mean period of 5.60 months (range 3-10 months) after the inverted ILM flap technique. The eyes that underwent FGE achieved higher rate of foveal restoration [complete external limiting membrane (ELM): 80%; complete ellipsoid zone (EZ): 60%] than those that didn’t receive FGE (complete ELM: 40%; complete EZ: 10%). Conclusions: Eyes that underwent FGE accelerated complete MH closure and showed better final vision and fovea l restoration.

In this work, optimal consumption and investment strategies are derived for risk-averse investors under the 4/2 stochastic volatility class of models. We work under an expected utility (EUT) framework and consider a Constant Relative Risk Aversion (CRRA) investor, who might also be ambiguity-averse. The corresponding Hamilton-Jacobi-Bellman (HJB) and HJB-Isaacs (HJBI) equations are solved in closed-form for a subset of the parametric space and under some restrictions on the portfolio setting, for complete markets. Conditions for proper changes of measure and well defined solutions are provided. These are the first analytical solutions for the 4/2 stochastic volatility model and the embedded 3/2 model for the type of excess returns established in .

The International Roughness Index (IRI) is the standard scale for evaluating road roughness in many countries in the world. The Taipei City government actively promotes a Road Smoothing Project and plans to complete the rehabilitation of the main and minor roads within its jurisdiction. This study aims to detect the road surface roughness in Taipei City and recommend appropriate IRI thresholds for road rehabilitation. A total of 171 asphalt concrete pavement sections in Taipei City with a total length of 803.49 km were analyzed and compared by IRI. The longitudinal profile of the detected road sections was measured using an inertial profiler. The statistical analysis showed that the IRI value prior to road leveling was mainly distributed between 5 and 8 m/km, while the IRI value after road leveling was mainly distributed between 3 and 4.5 m/km. This confirms that the implementation of the Road Smoothing Project has a significant effect on improving road smoothness. Moreover, based on the analysis results, it is recommended that the IRI threshold value for road rehabilitation in Taipei City be set at 4.50 m/km.

Multimodal remote sensing data classification can enhance the model’s ability to distinguish land features through multimodal data fusion. In this context, how to help models understand the relationship between multimodal data and target tasks is the focus of researchers. Inspired by human feedback learning mechanisms, causal reasoning mechanisms, and knowledge induction mechanisms, this paper integrates causal learning, reinforcement learning, and meta learning into a unified remote sensing data classification framework and proposed the causal meta-reinforcement learning (CMRL). First, based on feedback learning mechanisms, we have overcome the limitations of traditional implicit optimization of fusion features and customized a reinforcement learning environment for multimodal remote sensing data classification tasks. Through feedback interactive learning between agents and the environment, we help them understand the complex relationships between multimodal data and labels, thereby achieving full mining of multimodal complementary information. Second, based on the causal inference mechanism we designed causal distribution prediction action, classification reward, and causal intervention reward, capturing pure causal factors in multimodal data and cutting off false statistical associations between non-causal factors and class labels. Finally, based on the knowledge induction mechanism, we designed a bi-layer optimization mechanism based on meta-learning. By constructing a meta training task and meta validation task simulation model in the generalization scenario of unseen data, we helped the model induce cross-task shared knowledge, thereby improving its generalization ability for unseen multimodal data. The experimental results on multiple sets of multimodal datasets show that the proposed method achieved state-of-the-art performance in multimodal remote sensing data classification tasks.

Objective: To examine the effect of bilateral total lobectomy and unilateral total lobectomy on improving thyroid function in patients with thyroid micropapillary carcinoma treated with euthyrox. Methods: The study was conducted on 68 patients with thyroid micro papillary carcinoma treated with euthyroxwho had been surgically treated with euthyrox in our hospital between January 2018 and December 2019. On the basis of random number grouping, they were divided into control groups (n = 34, bilateral total lobectomy) and observation groups (n = 34, unilateral total lobectomy plus isthmectomy). Thyroid function, free triiodothyronine (FT3), thyroid hormone (TSH), and voice function (VHI score) of the two groups were compared.Results: In comparison to the control group, the observation group had shorter incision lengths, shorter operation times, and shorter hospital stays, as well as less intraoperative bleeding and drainage volume, and the difference was statistically significant (P < 0.05); As compared with the control group, the observation group had higher FT4 and FT3 levels as well as lower TSH levels, a statistically significant difference (P < 0.05).VHI scores of emotions, function, physiology, and other voice functions were significantly lower among the observation group than those of the control group (P < 0.05).Conclusion: A unilateral total lobectomy with adjacent isthmus resection in patients with thyroid micro papillary carcinoma can yield ideal results, accelerate the time taken for surgical rehabilitation, improve thyroid function, thereby improving voice quality, as well as improve the overall prognosis of the patient.

Drug-target affinity (DTA) prediction is crucial for understanding molecular interactions and aiding drug discovery and development. While various computational methods have been proposed for DTA prediction, their predictive accuracy remains limited, failing to delve into the structural nuances of interactions. With increasingly accurate and accessible structure prediction of targets, we developed a novel deep learning model, named S2DTA, to accurately predict DTA by fusing sequence and structural knowledge of drugs, targets, and pockets using heterogeneous models based on graph and semantic networks. Experimental findings underscored that complex feature representations imparted negligible enhancements to the model’s performance. However, the integration of heterogeneous models demonstrably bolstered predictive accuracy. In comparison to three state-of-the-art methodologies, the supremacy of S2DTA became strikingly apparent. It showcased a noteworthy 25.2% reduction in Mean Absolute Error (MAE) and an impressive 20.1% decrease in Root Mean Square Error (RMSE). Furthermore, S2DTA exhibited substantial advancements in other pivotal metrics, including Pearson Correlation Coefficient (PCC), Spearman, Concordance Index (CI), and R2. These metrics experienced remarkable increments of at least 19.6%, 17.5%, 8.1%, and a remarkable 49.4%, respectively. Finally, we conducted interpretability analysis on the effectiveness of S2DTA by bidirectional self-attention mechanism, fully proving that S2DTA is a valuable and accurate tool for predicting DTA. For further exploration, the source data and code repository can be accessed at https://github.com/dldxzx/S2DTA.

Starting from acid chlorides, alkynes, tryptamines, and acroyl chloride, 21 densely substituted tetrahydro-beta-carbolines are prepared in a four-component one-pot reaction. In this study, the aza-Michael addition step to generate intermediate enaminones is optimized in the presence of ytterbium triflate. Moreover, apart from acroyl chloride, all reactants can be deployed in almost equimolar ratios, which increases the atom economy of the sequence. For mechanistic rationali-zation, the concluding aza-anellation was investigated by DFT calculations on potential inter-mediates and corresponding activation energies, revealing that the aza-anellation rather pro-ceeds via ene-reaction than via electrocyclization.

This paper reviews the requirements for the production, quality, and quality assurance of solid recovered fuels (SRF) that are increasingly used for the substitution of fossil fuels in the indus-trial utilities. The economical, technological and environmental aspects should be considered before using SRF as an alternative fuel. In general, the most important factors determining the commercial production of SRF referred to the calorific values and their available amounts adopted in the starting materials. Furthermore, the low-melting impurities and undesired constituents/elements, including chlorine, sulfur, potassium and sodium, may pose negative impacts on air pollutant emission and slagging & fouling in the process utilities. In this regard, the vent emitted from the industrial utilities must comply with the effluent standards of station-ary sources like particulate, sulfur oxides, nitrogen oxides, heavy metals (e.g., lead, cadmium, and mercury) and dioxins. For these reasons, this work will summarize the legal or regulatory requirements under development in Asian countries (i.e., Japan, South Korea, and Taiwan) and European Union (EU). Finally, the outlook of solid recovered fuel (SRF) in the waste manage-ment and industrial sectors will be addressed to echo the sustainable development goals (SDGs).

A typhoon-induced storm surge is considered one of the most severe coastal disasters in Taiwan. However, the combination of the storm surge and the astronomical tide called the storm tide can actually cause extreme flooding in coastal areas. This study implemented a two-dimensional hydrodynamic model to account for the interaction between tides and storm surges on the coast of Taiwan. The model was validated with observed water levels at Sauo Fish Port, Hualien Port, and Chenggong Fish Port under different historical typhoon events. The model results are in reasonable agreement with the measured data. The validated model was then used to evaluate the effects of the typhoon's intensity, bathymetric change, and the combination of the typhoon’s intensity and bathymetric change on the maximum storm tide and its distribution along the east coast of Taiwan. The results indicated that the maximum storm tide rises to 1.92 m under a typhoon with an intensity of a 100-year return period. The maximum storm tide increased from a baseline of 1.26 m to 2.63 m for a 90% bathymetric rise at Sauo Fish Port under the conditions of Typhoon Jangmi (2008). The combination of the intensity of a typhoon with a 100-year return period and a 90% bathymetric rise will result in a maximum storm tide exceeding 4 m, 2 m, and 3 m at Sauo Fish Port, Hualien Port, and Chenggong Fish Port, respectively. We also found that the distribution of the maximum storm tide on the east coast of Taiwan can expand significantly subject to the bathymetric rise.

This paper aims at tackling with the task of fusion feature from images and its corresponding point clouds for 3D object detection in autonomous driving scenarios basing on AVOD, an Aggregate View Object Detection network. The proposed fusion algorithms fuse features targeted from Bird’s Eye View (BEV) LIDAR point clouds and its corresponding RGB images. Differs in existing fusion methods, which are simply the adoptions of concatenation module, element-wise sum module or element-wise mean module, our proposed fusion algorithms enhance the interaction between BEV feature maps and its corresponding images feature maps by designing a novel structure, where single level feature maps and another utilizes multilevel feature maps. Experiments show that our proposed fusion algorithm produces better results on 3D mAP and AHS with less speed loss comparing to existing fusion method used on the KITTI 3D object detection benchmark.

There is a current worldwide outbreak of a new type of coronavirus (2019-nCoV), which originated from China and has now spread to 17 other countries. Governments are under increase pressure to stop the outbreak spiraling into a global health emergency. At this stage, preparedness, transparency and sharing of information are crucial to risk assessments and beginning outbreak control activities. This information should include reports from outbreak sites, and from laboratories supporting the investigation. This paper aggregates and consolidates the virology, epidemiology, clinical management strategies from both English and Chinese literature, official news channels and other official government documents. In addition, by fitting the number of infections with a single-term exponential model, we report that the infection is spreading at an exponential rate, with a doubling period of 1.8 days.

In April 2019, a team of Keio University and Bucknell University students was assembled to participate in Ericsson Innovation Awards with a novel concept for generating renewable energy. This conceptual system consists of a vertical axis wind turbine, a crossflow marine hydrokinetic turbine, a floating platform integrated with a quadcopter system, and three to four temporary mooring lines with ship-type anchors. The proposed designed aims to offer solutions to two current problems of floating offshore wind energy: high construction cost of floating platforms and difficulties in maintenance of mooring lines. The combination of two vertical-axis turbines into a single floating platform would enable the system, namely ESwift, to extract energy from both wind and current resources. Additionally, due to the utilization of vertical axis turbines, the center of gravity of the proposed concept is significantly lower with respect to water level, compared to that of existing floating horizontal axis wind turbines, which would potentially reduce the floater's size and construction cost. Lastly, the integrated quadcopter mechanism would assist the floater in terms of stability and mobility, and enables an array of ESwifts to automatically rearrange for maximal energy generation. The authors hope that readers would find the idea described in this open access letter worth pursuing and would further develop and commercialize the ESwift concept.

[Introduction]: In the contemporary international financial environment, marked by intricate complexities and increasing uncertainties, the impact of exchange rate fluctuations on national economies has become increasingly significant. In this context, this study uses the Chinese economy as a case study to delve deeply into the interaction effects between macroprudential and monetary policies, analyzing how these policies jointly address economic instability. The aim is to offer new perspectives and strategies for stabilizing the global economic and financial landscape. [Methods]: This paper constructs an open-economy Dynamic Stochastic General Equilibrium (DSGE) model specifically tailored for China, incorporating Bayesian estimation and numerical simulation techniques. The study meticulously examines how macroprudential and monetary policies can be coordinated to achieve economic stability in response to exchange rate shocks. [Results]: The research finds that (1) targeted coordination of macroprudential and monetary policies towards asset prices and price levels can maintain stability under exchange rate shocks; (2) the effective implementation of such coordinated policies not only mitigates the fluctuations in asset prices due to exchange rate shocks but also enhances the level of societal welfare; (3) in terms of choosing an exchange rate regime, a managed floating rate system can prevent policy overlaps and conflicts that might occur in a floating rate system during the coordination of macroprudential and monetary policies, thus offering comparative advantages. [Discussion]: The findings underscore the importance of policy integration in a dynamic and complex global economic environment. They provide policy recommendations for China and other emerging market countries on how to effectively maintain economic stability through the synergistic interplay of macroprudential and monetary policies amid fluctuations in exchange rates and asset prices.

Isokinetic testing of the knee joint is the “gold standard” in strength assessment in sport especially in soccer, where it is part of pre-season screening to establish norms in case of injuries. There are many devices on the market that make it difficult to use of normative data. Isokinetics literature in females’ soccer players is scarce in comparison to males. Furthermore, evaluation protocols strongly differ from each other, using different ranges of speeds, movement patterns and output data. Thus, it is difficult for the researcher and the clinician to choose a correct protocol for isokinetic evaluation in female soccer players. The indexes of isokinetic performance that are widely accepted are the hamstring/quadriceps (H/Q) ratio and dominant/non-dominant (D/ND) ratio as reference. In this review are highlighted some common features of isokinetic testing in female soccer players of different levels of qualification. From this study, it emerges that, for a reliable test, 3 reps at the speed of 60°/sec in knee flexion/extension is preferable due to the high reliability and that an optimal H/Q ratio in healthy female soccer players of different level of qualification and age is 50%, while the interlimb differences (D/ND) should be below 10%.

The health benefits of purple sweetpotato, which is used as an edible food in its natural state and in processed foods and as a natural color pigment, have been recognized. In Japan, sweetpotato has been economically produced in regions below 36°4′N latitude, however, cultivation areas are beginning to expand further north. The anthocyanin and polyphenolics in purple sweetpotatoes cultivated in different locations; I (42°92′ N, 143°04′ E), II (35°99′ N, 140°01′ E), and III (31°72′ N, 131°03′ E), were compared over two years. Total anthocyanin and polyphenolic contents in purple sweetpotatoes tended to be high in location I. Their contents significantly differed over the two years in locations I and III and was dependent on temperature during cultivation. The anthocyanin and polyphenolic compositions differed between locations. The peonidin/cyanidin ratios were higher in location III compared with I and II in all varieties. The relative amount of chlorogenic acid was higher in location I, while the amount of 3,4- and 4,5-dicaffeoyolquinic acids were higher in location III, suggesting that the variability of the anthocyanin and polyphenolic content and composition was dependent on cultivation conditions. This study suggested that northern areas in Japan are an alternative production area and may yield higher amounts of anthocyanin and polyphenolics.

Our wellbeing is greatly influenced by our childhood and adolescence, and the relationships that we form during those phases of our development. The human-dog bond started thousands of years ago. The higher prevalence of dog ownership around the world, especially in households including children along with the growing number of people studying dogs most likely explain the growing literature focusing on child-dog interactions. We review the potential effects of child-dog interactions on the physical, mental, and social wellbeing of both species. A scoping search of the SCOPUS database found several hundred documents meeting selection criteria. It allowed us to define the numerous ways in which children and dogs can interact, be it neutral (e.g., sharing a common area), positive (e.g., petting), or negative (e.g., biting). Then, we found evidence for an association between interacting with dogs during childhood and an array of health and mental benefits like stress relief and the development of empathy. Walking a dog and playing with one are perfect physical activity opportunities. Additionally, interacting with a dog can help lower stress and may have a role in the development of empathy. Nonetheless, a number of detrimental outcomes have also been identified in both humans and dogs. Children are the most at-risk population regarding dog bites and dog-borne zoonoses, which may lead to a subsequent fear of dogs or even death. Moreover, pet bereavement is generally inevitable when living with a canine companion and should not be trivialized. In terms of dogs, children sometimes take part in caretaking behaviors toward them which include going on walks. They are opportunities for dogs to relieve themselves outside, but also to exercise and socialize. In contrast, a lack of physical activity can lead to the onset of obesity. Dogs may present greater levels of stress when in the presence of children. Finally, the welfare of assistance, therapy, and free-roaming dogs remains underexplored. Overall, the study of the effects, positive as well as negative, on both species still requires further development. We call for more longitudinal studies and hope for cross-cultural research in the future in order to better understand the impact child-dog interactions might have.