The increasing demand for higher power in rocket launchers is driving the development of higher power nozzles, achieved essentially by increasing the expansion ratio. However, this can lead to flow separation and resulting unsteady, asymmetrical forces, called side loads, which can limit the life of both the nozzle itself and other engine components. If this problem can be overcome, engine performance can be significantly increased. Therefore, various separation control methods have been proposed, but none have been fully implemented to date due to the uncertainties associated with modeling and predicting the flow phenomena. A numerical study of high area ratio rocket engine is presented to analyze the aeroelastic performance of the structure under the condition of flow separation. The finite volume method, the 2nd order upwind scheme and the extended wall function are used to analyze the flow inside the rocket nozzle and the transition of the Free Shock Separation (FSS) to Restricted Shock Separation (RSS) separation pattern ) to be discussed in detail. Since the location of the flow separation point depends heavily on the flow.

Pea shoots is a popular vegetable in certain regions of the world due to their unique taste and abundance of health-promoting phytochemicals. The perishable nature and susceptibility of root rot of pea shoots necessitate a new soilless production system located close to the market. This study compared the growth of pea shoots using various cultivation methods in LED plant factory. The results showed that early topping (4 days after transplanting, ET) promoted early harvest compared to later topping (20 days after transplanting, LT) and increased the number of harvested shoots by extending the harvest time to 2.8 times, ultimately resulting in a substantial yield improvement. Moreover, the yield of ET with lower planting density (72 plants m-2, ET-LD) was 8.7% higher than ET with higher planting density (126 plants m-2, ET-HD). Particularly, the average fresh weight of individual pea shoots under ET-LD exceeded that of ET-HD by 48.9%. It is advisable to consider adopting ET-LD for the cultivation of pea shoots in LED plant factory. Based on ET-LD, the yield, nutritional quality, and light use efficiency of pea shoots were further explored at different stages under three levels of light intensity (50, 100, 150 μmol m-2 s-1). Contrasted against the light intensity of 50 μmol m-2 s-1, the average fresh weight per pea shoots, number of harvested, and total fresh yield under light intensity of 150 μmol m-2 s-1 treatment increased by 60.2%, 62.8%, and 165.1%, respectively. Meanwhile, the fresh weight per pea shoots, photosynthetic capacity, soluble sugar and vitamin C levels in leaves, as well as light use efficiency and photon yield, initially increased and then decreased with the extension of the planting period. Among these, soluble sugar, LUE, and PY started to decrease after reaching the maximum value at 60-70 days after transplanting. In conclusion, light intensity of 150 μmol m-2 s-1 with a photoperiod of 16 h d-1 using LEDs, combined with early topping within a planting period of 60-70 days, proves to be suitable for the hydroponic production of pea shoots in LED plant factory.

The crystal structure of quintinite, Mg4Al2(OH)12(CO3)·3H2O, from Jacupiranga alkaline complex (Cajati, São Paulo, Brazil) has been refined for two samples (91002 and C7029) using single-crystal X-ray diffraction data. The mineral crystallizes in the P-3c1 space group, a = 5.246/5.298, c = 15.110/15.199 Å for the samples 91002/C7029. The crystal structure consists of octahedral sheets with Mg and Al ordering according to the 3 × 3 superstructure. The Mg and Al atoms are coordinated by six hydroxylated oxygen atoms each with the average <Mg–O> and <Al–O> bond distances being in the ranges 2.022–2.053 Å and 1.974–1.978 Å, respectively. The interlayer structures are identical (in contradiction to the previous assumptions) and compose from disordered (CO3)2- groups and (H2O)0 molecules. The samples from Jacupiranga can be identified as quintinite-2T that is the second find of the polytype after the Kovdor alkaline complex (Kola peninsula, Russia). The powder X-ray diffraction pattern of quintinite-2T contains weak superstructure reflection at 4.57 Å (010) indicative of Mg and Al ordering. An important crystal-chemical criterion of quintinite is the interlayer distance (d00n-value) of ~ 7.56 Å, which is steady for natural specimens from various findings worldwide.

The article describes the study of the properties of polytetrafluoroethylene, modified using natural layered silicates—serpentinite. It is shown that the introduction of a small amount of layered silicates significantly increases the tribological characteristics of the material. The additional introduction of magnesium nano-spinels facilitated the formation of an intercalated polymer-silicate nanocomposite.

Materials engineering based on metal oxides for manipulating the solar spectrum and producing solar energy have been under intense investigation over the last years. In this work, we present NiO thin films double-doped with niobium (Nb) and nitrogen (N) as cation and anion dopants (NiO:(Nb,N)) to be used as p-type layers in all oxide transparent solar cells. The films were grown by sputtering a composite Ni-Nb target on room-temperature substrates in plasma containing 50% Ar, 25% O2 and 25% N2 gases. The existence of Nb and N dopants in the NiO structure was confirmed by the Energy Dispersive X-Ray and X-Ray Photoelectron Spectroscopy techniques. The nominally undoped NiO film, which was deposited by sputtering a Ni target and used as the reference film, was oxygen-rich, single-phase cubic NiO, having a visible transmittance of less than 20%. Upon double doping with Nb and N the visible transmittance of NiO:(Nb,N) film increased to 60%, which was further improved after thermal treatment to around 85%. The respective values of the direct band gap in the undoped and double-doped films were 3.28 eV and 3.73 eV just after deposition and 3.67 eV and 3.76 eV after thermal treatment. The changes in the properties of the films such as structural disorder, direct and indirect energy band gaps, Urbach tail states and resistivity were correlated with the incorporation of Nb and N in their structure. The thermally treated NiO:(Nb,N) film was used to form a diode with a spin-coated two-layer, mesoporous on top of a compact, TiO2 film. The NiO:(Nb,N)/TiO2 heterojunction exhibited visible transparency of around 80%, showed rectifying characteristics and the diode’s parameters were deduced using the I-V method. The diode revealed photovoltaic behavior upon illumination with UV light exhibiting a short circuit current density of 0.2 mA/cm2 and open-circuit voltage of 500 mV. Improvements of the output characteristics of the NiO:(Nb,N)/TiO2 UV-photovoltaic by proper engineering of the individual layers and device processing procedures are addressed. Transparent NiO:(Nb,N) films can be potential candidates in all-oxide ultraviolet photovoltaics for tandem solar cells, smart windows and other optoelectronic devices.

The microstructures and mechanical properties of the hot-rolled Fe-6.5wt.%Si sheet are analyzed. The microstructure of the hot-rolled sheet is layered along the thickness direction. The surface exhibits fine and equiaxed grains, whereas the center part shows coarse and elongated grains with a <101> fiber texture along the rolling direction. Serrated flow behavior is observed during tensile deformation of both the hot-rolled sheet and its center samples at 350 °C; thus, the serrated flow of the hot-rolled sheet is mainly attributed to the serration of the center part. The analyses of dislocation configurations, ordered structures, and crystal orientation show that the serrated flow behavior results from the interaction of solutes with mobile dislocations. Mobile dislocations are pinned by combining parallel forest dislocations with the pipe diffusion of solution atoms. This study provides a new perspective for the deformation mechanism of the Fe-6.5wt.%Si alloy.

Understanding the stability limit of crystalline materials under variable tensile stress conditions is of capital interest for their technological applications. In this study, we present results from first-principles density functional theory calculations that quantitatively account for the response of selected covalent and layered materials to general stress conditions. In particular, we have evaluated the ideal strength along the main crystallographic directions of 3C and 2H polytypes of SiC, hexagonal ABA stacking of graphite and 2H-MoS2. Transverse superimposed stress on the tensile stress was taken into account in order to evaluate how the critical strength is affected by these multi-load conditions. In general, increasing transverse stress from negative to positive values leads to the expected decreasing of the critical strength. Few exceptions found in the compressive stress region correlate with the trends in the density of bonds along the directions with the unexpected behavior. In addition, we propose a modified spinodal equation of state able to accurately describe the calculated stress-strain curves. This analytical function is of general use and can also be applied to experimental data anticipating critical strengths and strains values and providing informattion on the energy stored in tensile stress processes.

In the present work, an innovative range of foams, based on flax gum-filled epoxy resin was developed, reinforced or not by flax fibers. Foams and composites with different gum and epoxy resin contents were produced and characterized for mechanical and thermal performances. To enhance the organic flax gum filler's cross-linking, we exploited the oxidized components' reactivity with the amine hardener (isophorone diamine). We compared the materials obtained with those derived from the native components. Flax gum and fibers were primarily characterized by chemical analysis, NMR, and FTIR to evaluate the mild oxidation of native materials. The formation of chemical bonds between oxidized polymer chains, epoxy resin, and hardener has been evidenced by FTIR, and the materials were then studied by SEM, X-ray computed micro-tomography (CT), and submitted to mechanical and thermal tests. The relevance of oxidation treatment was highlighted, through a significant increase in density and mechanical performances (+36% and +81%, respectively for the 100% flax gum material). The positive effect of flax fibers on homogeneity evidenced through micro-CT analysis was also clearly addressed. This set of promising results paves the way for future development of fully flax-based insulation composite materials.

Pipeline conflicts arising from data dependencies are a common issue encountered in the hardware implementation of layered QC-LDPC decoders. This paper proposes an efficient layered decoding architecture to reduce pipeline conflicts without introducing stall cycles, by reordering the processing order offline and using the patch method based on variable-to-check message. The experimental results on the LDPC code of the IEEE802.16 standard in the OFDM-PON system demonstrate that the proposed architecture has a sensitivity improvement of 0.125 dBm and 0.375 dBm, respectively, compared with our previous work and the method described in the other work.

In a saline semi-isolated Lagoon on the Cape Zeleny (White Sea), the annual dynamics of the vertical hydrological structure, and the seasonal dynamics of phytoplankton were traced, including species composition, and vertical distribution, abundance, nutrition type,and biomass.293 species and supraspecific taxa of algae and cyanobacteria were found. Most of the identified species are marine, and 38 species are freshwater. Taxonomic composition changed in the Lagoon during the year. Dinoflagellates dominated in winter and early June; unidentified cocci and flagellates in July; diatoms, dinoflagellates and unidentified cells in August; dinoflagellates in September; and unidentified cocci and flagellates in October–November. The abundance of algae also changed in the Lagoon during the year. The integrated biomass in the water column varied from 0.01 g C/m2 in January to 0.78 g C/m2 in early September. According to the abiotic parameters, the water column of the Lagoon is subdivided into several zones with different conditions and corresponding phytoplankton communities. Similarity between the communities of different horizons was 32-46% in summer and 7% in winter. The chemocline layer was the most populous. Almost the entire year it contained a maximum of phytoplankton biomass, 1-2 orders of magnitude higher than that in the overlying horizons. Comparison phytoplankton in the lagoon and in the nearby sea area was carried out. Despite the connection between the Lagoon and the sea phytoplankton structure in the surface water layer in the Lagoon and in the sea differs significantly in composition, quantitative parameters, and seasonal dynamics. The similarity of the communities in the sea and the Lagoon never exceeded 50%. In terms of biomass, the Lagoon lags behind the sea until mid-summer, but, starting from August, it outnumbers it, and the phytoplankton development in the Lagoon lasts longer, until late autumn. The phytoplankton structure and dynamics in the Lagoon and the sea by 24.5% was related to the daylight, water salinity, oxygen content and pH, but did not depend on water T, underwater illuminance, and depth. Oxygen content and pH are defined by PhP activity. Salinity serves as a vector of the vertical sequence of ecological niches. The daylight length seems to be the crucial factor of the seasonal PhP dynamics in the semi-isolated coastal stratified lakes and lagoons.

Lithium rich layered oxides (LRLO) are a wide class of innovative active materials for positive electrodes in lithium-ion (LIB) and lithium-metal secondary batteries (LMB). LRLOs are over-stoichiometric layered oxides rich in lithium and manganese, with general formula Li1+xTM1-xO2, where TM is a blend of transition metals comprising Mn (main constituent), Ni, Co, Fe and others. Due to the very variable composition and the extended defectivity their structural identity is still debated among researchers being likely an unresolved hybrid between a monoclinic (mC24) and a hexagonal lattice (hR12). Once casted in composite positive electrode films and assembled in LIBs or LMBs, LRLOs can delivery reversible specific capacities above 220-240 mAhg-1, thus beyond any other available intercalation cathode material for LIBs, with mean working potential above 3.3-3.4 V vs Li for hundreds of cycles in liquid aprotic commercial electrodes. In this review we critically outline the recent advancements in the fundamental understanding of the physico-chemical properties of LRLO as well as the most exciting innovations in their battery performance. We focus in particular on the elusive structural identity of these phases, on the complexity of the reaction mechanism in batteries as well as on practical strategies to minimize or remove cobalt from the lattice while preserving the outstanding performance upon cycling.

A configurable design of a microstrip square spiral RFID tag antenna, for a wide range of microwave frequencies in S- and C-band, is presented. The design is parameterized in dimensions, and hence changing the design frequency (or frequencies) is easy, by changing only an initial value for the spiral geometry. A tag specimen was fabricated using Cu electroplating technique according to the design for frequencies of interest in the areas of 2.4 and 5.8 GHz. The substrate material is a 320 μm high resistivity Si and the bridge dielectric is a 15μm polyimide PI2525. The microfabrication process involves steps of metallic structure pattern transfer techniques with optical UV lithography procedures. The reflection coefficient and gain of the specimen were measured inside an anechoic enclosure using a vector network analyzer (VNA) and a TEM horn test antenna over a frequency range of up to 6 GHz. Simulated and measured results are presented and discussed, exhibiting reasonable agreement.

By repeated unloading and loading of the excavation dynamic and static loads, repeated train dynamic and static loads of multi-factors, the underpass tunnel, cross tunnel engineering influence area rock layer, the existing tunnel structure of the three constitutes a multifaceted structure, multi-factor interaction system. Existing tunnels into the prediction theory model of the new tunnel excavation process of dynamic and static loads, dynamic and static loads of existing tunnels are mostly analyzed individually, the results of synergistic analysis needs to be improved. Based on the theory of the current layer method, the paper comprehensively considers the stiffness of the existing tunnel, the stiffness of the new tunnel, the excavation method load and the existing tunnel load, coupled with Peck's empirical formula, the theoretical model of deformation prediction for excavation of a two-lane highway tunnel under the tunnel through the existing railroad is proposed, and verified and optimized by numerical calculations and monitoring data, which proves the applicability and reliability of the theoretical model in the similar strata and the project promotion.

In contemporary construction, the prevalence of vibration serviceability issues in lightweight and slender structures has become increasingly common, owing to advancements in building materials and construction methods. While these structures often meet the criteria for ultimate limit states, they can still elicit complaints due to excessive vibrations induced by human activity. To address this challenge, the Integral Resonant Control (IRC) technique has emerged as a favored approach for actively damping vibrations in various systems. This study introduces a fresh perspective on implementing a multi-input multi-output (MIMO) IRC scheme for active vibration control (AVC) specifically tailored for pedestrian structures utilizing inertial mass actuators. Building upon a common framework and design methodology outlined in previous research, this work presents a novel application of MIMO IRC for AVC. The designed controller is rigorously tested and implemented on a laboratory floor structure to validate its efficacy.

The bulk backscattering ratio ($\tilde{b_{bp}}$) is commonly used as a descriptor of the bulk real refractive index of the particulate assemblage in natural waters. Based on numerical simulations, we analyze the impact of heterogeneity of phytoplankton cells on $\tilde{b_{bp}}$. $\tilde{b_{bp}}$ is modeled considering viruses, heterotrophic bacteria, phytoplankton, detritus, and minerals. Three study cases are defined according to the relative abundance of these different components. Two study cases represent typical situations in open ocean, outside (No-B/No-M) and inside bloom (B/No-M). The third study case is typical of coastal waters with the presence of minerals. Phytoplankton cells are modeled by a two-layered spherical geometry representing a chloroplast surrounding the cytoplasm. The $\tilde{b_{bp}}$ values are higher when heterogeneity is considered because the contribution of coated spheres to backscattering is higher than homogeneous spheres. The impact of heterogeneity is however strongly conditioned by the hyperbolic slope $\xi$ of the particle size distribution. Even if the relative concentration of phytoplankton is small (<1%), $\tilde{b_{bp}}$ increases by about 60% (for $\xi=4.3$ and for the No-B/No-M water body), when the heterogeneity is taken into account, in comparison with a particulate population only composed by homogeneous spheres. As expected, heterogeneity has a much smaller impact (about 5$\%$ for $\xi=4.3$) on $\tilde{b_{bp}}$ when minerals are added.

Layered superconductors are attractive because some of them show high critical temperatures. While their crystal structures are similar, those compounds are composed of many elements. Compounds with many elements tend to be incongruent melting compounds, thus, their single crystals cannot be grown via the melt-solidification process. Hence, these single crystals have to be grown below the decomposition temperature, and then the flux method, a very powerful tool for the growth of these single crystals with incongruent melting compounds, is used. This review shows the flux method for single-crystal growth technique by self-flux, chloride-based flux, and HPHT (high-pressure and high-temperature) flux method for many-layered superconductors: high-T_c cuprate, Fe-based and BiS₂-based compounds.

With the burgeoning growth of online retail, the issue of counterfeit products has become a significant threat to both consumer trust and brand integrity, posing challenges to sustainable market practices. Online retail platforms are promoted to redesign their channel structures and enhance brand traceability to tackle counterfeits using blockchain technology. To investigate the interactions between blockchain technology and the channel structures of online retail platforms, we design a game theory model incorporating a manufacturer with(out) blockchain participation selling products via an online retail platform that operates an agency channel and/or a reselling channel. We show that the critical trade-off of blockchain participation comprises the brand assurance effect of the blockchain, the channel competition intensification effect, and the blockchain adoption cost. The platform is capable of strategically designing the channel structure to encourage (while discouraging) blockchain participation by the manufacturer. Our analysis highlights the complementarity between blockchain participation and the channel structure. Furthermore, the effect of the consumer’s belief in the reselling channel, the commission fee in the agency channel, and the substitutability between channels are investigated in depth. The research provides valuable insights for online retail platforms and policymakers seeking to foster a sustainable and trustworthy e-commerce ecosystem.

This article explores the cutting-edge advancement of gypsum and cement building boards infused with shape-stabilized n-octadecane, an organic phase change material (PCM). The primary focus is on improving energy efficiency and providing electromagnetic interference (EMI) shielding capabilities for contemporary buildings. The research investigates the integration of these materials into construction materials, using red-mud Carbon Foam as a stabilizer for n-octadecane (OD@CCF). Various analyses, including microstructural examination, porosity assessment, and additive dispersion, were conducted using X-ray microtomography and density measurements. Thermal conductivity measurements demonstrated the enhancement of composite boards as the OD@CCF content increased, while mechanical tests indicated an optimal additive content of up to 20%. The thermal-regulated capabilities of these advanced panels were evaluated in a custom-designed room model equipped with a homemade environmental chamber, illustrating a consistent temperature environment during heating and cooling cycles. The incorporation of OD@CCF into cement boards exhibited improved thermal energy storage properties. Moreover, the examined composite boards displayed efficient electromagnetic shielding performance within the frequency range of 3.2–7.0 GHz, achieving EMI values of approximately 18 and 19.5 dB for gypsum and cement boards, respectively, meeting the entry-level value required for commercial applications.

We present a series of computer-assisted high resolution transmission electron (HRTEM) simulations to determine Moiré patters by induced twisting effects between slabs at rotational angles of 3°, 5°, 8°, and 16°, for molybdenum disulfide, graphene, tungsten disulfide, and tungsten selenide layered materials. In order to investigate the electronic structure, a series of numerical simulations using DFT methods was completed using CASTEP with a generalized gradient approximation to determine both band structure and density of states on honeycomb like new superlattices. Our results indicate metallic transitions when rotation approaches 8° with respect to each other for most of the two-dimensional systems that were analyzed.

In this work, we introduce the first pipeline that combines a refraction-aware Structure-from-Motion (SfM) method with a deep learning model specifically designed for airborne bathymetry. We accurately estimate the 3D positions of the submerged points by integrating refraction geometry within the SfM optimization problem. This way, no refraction correction as post-processing is required. Experiments with simulated data that approach the real-world capturing conditions demonstrate that SfM with refraction correction is extremely accurate, with submillimeter errors. We integrate our refraction-aware SfM within a deep learning framework that also takes into account radiometrical information, developing a combined spectral and geometry-based approach, with further improvements on accuracy and robustness to different seafloor types, both textured and textureless. We conducted experiments with real-world data at 2 locations in the southern Mediterranean Sea, with varying seafloor types which demonstrate the benefits of refraction correction for the deep learning framework. We open-source our refraction-aware SfM, providing researchers in airborne bathymetry with a practical tool to apply SfM in shallow water areas.

By using the particle swarm optimization algorithm for crystal structure prediction, we reveal a newly orthorhombic Cmcm structure of HfB4, which is more energetically superior to the previously proposed YB4-, ReP4-, FeB4-, CrB4-, and MnB4-type structures in the considered pressure range. The phonon dispersion and elastic constants calculations confirm that the new phase is dynamically and mechanically stable. The calculated large shear modulus (240 GPa) and high hardness (45.7 GPa) imply that the predicted Cmcm-HfB4 is a potential superhard material. Meanwhile, the directional dependences of the Young's modulus, bulk modulus, and shear modulus for HfB4 are systematically investigated. Further analyses of the density of states and electronic localization function indicate that the strong B-B and B-Hf covalent bonds greatly contribute to its high hardness and stability.

The nucleation and dynamics of Josephson and Abrikosov vortices determine the critical currents of layered high-T_c superconducting (HTS) thin films, grain boundaries, and coated conductors, so understanding their mechanisms is of crucial importance. Here we treat pair creation of Josephson and Abrikosov vortices in layered superconductors as a secondary Josephson effect, in which each full vortex is viewed as a composite fluid of micro-vortices, such as pancake vortices, which tunnel coherently via a tunneling matrix element. We introduce a two-terminal magnetic (Weber) blockade effect that blocks tunneling below a threshold current, and simulate time-correlated vortex tunneling above threshold. The model shows nearly precise agreement with voltage-current (V-I) characteristics of HTS cuprate grain boundary junctions, which becomes more concave rounded as temperature decreases, and also explains the piecewise linear V-I behavior observed in iron-pnictide bicrystal junctions and other HTS devices. When applied to either Abrikosov or Josephson pair creation, the model explains a plateau seen in plots of critical current vs. thickness of HTS coated conductors. The observed correlation between theory and experiment strongly supports the proposed quantum picture of vortex nucleation and dynamics in layered superconductors.

Over the past few years, we have experienced great technological advancements in the information and communication field, which has significantly contributed to reshaping the Intelligent Transportation System (ITS) concept. Evolving from the platform of a collection of sensors aiming to collect data, the data exchanged paradigm among vehicles is shifted from the local network to the cloud. With the introduction of cloud and edge computing along with ubiquitous 5G mobile network, it is expected to see the role of Artificial Intelligence (AI) in data processing and smart decision imminent. So as to fully understand the future automobile scenario in this verge of industrial revolution 4.0, it is necessary first of all to get a clear understanding of the cutting-edge technologies that going to take place in the automotive ecosystem so that the cyber-physical impact on transportation system can be measured. CIoV, which is abbreviated from Cognitive Internet of Vehicle, is one of the recently proposed architectures of the technological evolution in transportation, and it has amassed great attention. It introduces cloud-based artificial intelligence and machine learning into transportation system. What are the future expectations of CIoV? To fully contemplate this architecture’s future potentials, and milestones set to achieve, it is crucial to understand all the technologies that leaned into it. Also, the security issues to meet the security requirements of its practical implementation. Aiming to that, this paper presents the evolution of CIoV along with the layer abstractions to outline the distinctive functional parts of the proposed architecture. It also gives an investigation of the prime security and privacy issues associated with technological evolution to take measures.

The SK model proposed by Sherrington and Kirkpatrick is an important mean field model for spin glasses. The dependence structure of Hamiltonians of the SK model is considered in this paper. We have investigated the covariance matrix of Hamiltonians of the SK model, and establish a relationship between the rank of the corresponding covariance matrix and the dimension of the space spanned by the Hamiltonians. Finally, we also give an upper bound for the rank of the covariance matrix, which might be the best.

Estimating the ocean’s subsurface thermohaline information from satellite measurements is essential for understanding ocean dynamics and El Niño phenomenon. This paper proposes an improved double-output Residual Neural Network (DO-ResNet) model to concurrently estimate the ocean subsurface temperature (OST) and ocean subsurface salinity (OSS) in the tropical Western Pacific using multi-source remote sensing data, including sea surface temperature (SST), sea surface salinity (SSS), sea surface height anomaly(SSHA), sea surface wind (SSW), and geographical information (including longitude (LON) and latitude (LAT)). In the model experiment, Argo data were used to train and validate the model, and the root mean square error (RMSE), normalized root mean square error (NRMSE) and coefficient of determination (R²) were employed to evaluate the model's performance. The results showed that the sea surface parameters selected in this study have a positive effect on the estimation process, and the average RMSE and R² values for estimating OST (OSS) by the proposed model are 0.34 °C (0.05 psu) and 0.91 (0.95), respectively. Under the data conditions considered in this study, DO-ResNet demonstrates superior performance relative to the extreme gradient boosting model, random forest model, and artificial neural network model. Additionally, this study evaluates the model’s accuracy by comparing its estimations of OST and OSS across different depths with Argo-derived data, demonstrating the model's ability to effectively capture the most spatial features, and by comparing NRMSE across different depths and seasons, the model displays strong seasonal adaptability. In conclusion, this research introduces a novel artificial intelligence technique for estimating OST and OSS in the tropical Western Pacific Ocean.

In this paper, a new axial-type magnetic gear with auxiliary flux-enhancing structure (AFS-AMG) is proposed. Compared to conventional AFS-AMG, it has the higher torque density and higher permanent magnet (PM) utilization factor. Firstly, the design rules and operating principles of proposed AFS-AMG are elaborated. Then, the mapping relation between the radial-type magnetic gears (RMGs) and AMGs are elucidated. Compared to its counterpart in RMGs, AFS-AMGs achieve small size. Then, the geometrical parameters of AFS-AMGs are optimized to obtain the better electromagnetic performances, where the torque density per volume and per PM volume is adopted as the evaluation standard. Finally, three different AMG topologies are constructed in finite element analysis (FEA) software for comparison. It is proven that the AFS-AMG has the largest torque density per volume and per PM volume.

This study extends the CGAN-based MODIS cloud vertical-profile (64×64-scene, about 70km width×15km height) retrieval technique developed by Leinonen et al. (2019) [1] to construct seamless 3D cloud fields for the MODIS granules [2]. Firstly, the accuracy and spatial continuity of the Leinonen et al. [1] retrievals are statistically evaluated. Then, according to the characteristics of the retrieval error, a spatially overlapping-scene ensemble generation method and a bi-directional Ensemble Binning Probability Fusion (CGAN-BEBPF) technique are developed, which improves the CGAN retrieval accuracy and support to construct seamless 3D clouds. The CGAN-BEBPF technique involves three steps: cloud masking, intensity scaling, and optimal value selection. It ensures adequate coverage of the low reflectivity areas while preserving the high reflectivity cloud cores. The technique is applied to retrieve the 3D cloud fields of Typhoon Chaba and a multi-cell convective system. The cloud structures of the CGAN-BEBPF results are highly consistent with the ground-based radar observations. It can retrieve weak clouds at the top levels of convective storms and hurricanes that were missed by ground-based radars and fill the gaps of the ground-based radar lower-level PPI scan. Overall, CGAN-BEBPF can be automated to retrieve the rich informative 3D structures of typhoons and severe convective systems over the oceans along the MODIS swath, which certainly presents great value for improving maritime and near-shore typhoons and convection prediction and other cloud-sensitive applications.

Floral nectar is a key reward in Leguminosae despite the exceptional diversity of flowers in this family. The paper aims to summarize the available data on structure, ontogeny, regulation, and possible evolution of the leguminous floral nectaries. To date, detailed characterization of ultrastructure and mode of secretion is available only for a few representative of the family whereas the majority remains understudied from this perspective. In most cases, regardless of flower symmetry, nectaries are localized between stamens and a carpel. The nectar is usually exuded from modified stomata although the exact mode of secretion by specialized parenchyma may differ between taxa. The leguminous floral nectaries often have certain features of monosymmetry with preferentially abaxial development. Nectaries were independently lost in several lineages, and equally recurrent is the emergence of substitutive, i.e. evolutionary innovative, nectar-producing structures. Floral nectaries possess a certain degree of evolutionary inertia, i.e. they remain stable even in lineages in which flower morphology underwent significant changes compared with an ancestral plan, such as shifts in merism, symmetry, organ number and alike. Due to their evolutionary stability, floral nectaries are rarely used in taxonomy of Leguminosae.

The attitude dynamics and orbit dynamics of large rigid space structures are coupled with each other under gravity gradient, which may affect the stability of the large rigid space structures. In this paper, the gravity gradient stability of a large rigid space structure is studied under both small and large disturbances. Based on the rigid body dynamics and orbit dynamics, an accurate dynamic model without any linearization of the large rigid space structure is established via the natural coordinate formulation (NCF), which is able to describe the large overall motions of the structures. By using the generalized-α algorithm, the gravity gradient stability of the large rigid space structure is simulated and analyzed via various examples, including the influence of large disturbance angles, the positions at the stabilization and unstabilization regions. Finally, the relationship between spinning stability and gravity gradient stability is also investigated via a large spinning space structure.

The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

Water splitting plays an important role in electrochemical and photoelectrochemical conversion of energy devices. Electrochemical water splitting by the hydrogen evolution reaction (HER) is a straightforward route to produce hydrogen (H2), which requires an efficient electrocatalysts to minimize energy consumption. Recent advances have created a rapid rise in new electrocatalysts, particularly those based on non-precious metals. In this review, we present a comprehensive overview of the recent developments of ternary and quaternary 6d-group transition metal chalcogenides (TMCs) based electrocatalysts for water splitting, especially for HER. Detailed discussion is organized from binary to quaternary TMCs including, surface engineering, heterostructures, chalcogen substitutions, and hierarchically structural design in TMCs. Moreover, emphasis is placed on future research scope and important challenges facing these electrocatalysts for further development in their performance towards water splitting.

Lignin is insoluble in water, limiting its use in the synthesis of adhesives. Therefore, in order to increase the amount of lignin raw materials used in the synthesis of adhesives, a kind of aminated lignin compounds was prepared through lignin amination reaction, and conducting structural analysis in this paper. The particle size of the amino lignin is about 100 nm, with the weight average molecular weight of 57,627 g/mol and a water solubility of 0.45g/100ml. The reaction mechanisms were proposed that the phenolic hydroxyl groups of lignin react with ammonia molecules, and thereby successfully introducing amino groups to generate the aminated lignin compounds. Therefore, this article enriches the scientific theory of lignin reactions and provides reference for the widespread application of lignin raw materials in the field of adhesives.

Knowledge is not merely the characteristic of certain pieces of information being deemed true and justifiable, but rather a process. Within an axiomatic system, the set of information that reaches the status of knowledge forms a universe that provides an interpretation of the reality one aims to describe. Language exchanges information through communication and the process of justification (exchange of information), if it consistently justifies a particular piece of information, it elevates it to knowledge. In this paper, we provide a framework for knowledge within an axiomatic model where we define the fundamental elements of communication and grammar. As a result, the structure dictates that knowledge, to be considered as such, must be investigateable by anyone who utilizes it in its entirety, both in form and content. Ultimately, the development of knowledge processing, referred to as \emph{knowmatics}, represents a clear evolution of the computer science that processes information (subset of knowledge).

In this study we have investigated the effect of the addition of Nb2O5 (up to 5 mol%) on the structure and luminescent properties of ZnO-B2O3 glass doped with 0.5 mol % Eu2O3 by using of infrared (IR), Raman and photoluminescence (PL) spectroscopy. Physical properties as molar volume, oxygen packing density and glass transition temperature were determined using the results of differential thermal analyisis (DTA) and Archimedes principle for density. IR and Raman spectra revealed that niobium ions incorporate into the base zinc borate glass as NbO4 trtraherda and NbO6 octahedra. A strong red emission from the 5D0 level of Eu3+ ions was registered under near UV (392 nm) excitation using the sharp 7F0 - 5L6 transition of Eu3+. The integrated fluorescence intensity ratio R (5D0 → 7F2/5D0 → 7F1) was calculated to estimate the degree of asymmetry around the active ion, suggesting a location of Eu3+ in non-centrosymmetric sites. The higher Еu3+ luminescence emission observed in zinc borate glasses containing 1÷5 mol% Nb2O5 compared to the Nb2O5-free zinc borate glass evidences that Nb2O5 is suitable component for modification of host glass structure and improving the emission intensity.

The atomic structures of Zn and Na borophosphate glasses were studied by X-ray and neutron diffraction. Peaks assigned to the B−O, P−O, and O−O distances confirm that only BO4 units co-exist with the PO4 tetrahedra. The Zn−O and Na−O coordination numbers are found to be a little larger than four. The narrowest peaks of the Zn−O first-neighbor distances exist for the glasses along a line connecting the Zn(PO3)2 and BPO4 compositions (50 mol% P2O5) which is explained by networks of ZnO4, BO4, and PO4 tetrahedra with twofold coordinated oxygens. Calculated amounts of the available oxygen support this interpretation. Broadened peaks occur for glasses with lower P2O5 contents, consistent with the presence of threefold coordinated oxygens. The two distinct P−O peak components of the Zn and Na borophosphate glasses differ in their relative abundances which is interpreted by Na+ cations that coordinate oxygens in some P−O−B bridges, something not seen for the Zn2+ ions.

Ecosystem physical structure, defined by the quantity and spatial distribution of biomass, influences a range of ecosystem functions. Remote sensing tools permit the non-destructive characterization of canopy and root features, potentially providing opportunities to link above- and belowground structure at fine spatial resolution in functionally meaningful ways. To test this possibility, we employed ground-based portable canopy lidar (PCL) and ground penetrating radar (GPR) along co-located transects in forested sites spanning multiple stages of ecosystem development and, consequently, of structural complexity. We examined canopy and root structural data for coherence at multiple spatial scales ≤ 10 m within each site using wavelet analysis. Forest sites varied substantially in vertical canopy and root structure, with leaf area index and root mass more evenly distributed by height and depth, respectively, as forests aged. In all sites, above- and belowground structure, characterized as mean maximum canopy height and root mass, exhibited significant coherence at a scale of 3.5-4 meters, and results suggest that the scale of coherence may increase with stand age. Our findings demonstrate that canopy and root structure are linked at characteristic spatial scales, which provides the basis to optimize scales of observation. Our study highlights the potential, and limitations, for fusing lidar and radar technologies to quantitatively couple above- and belowground ecosystem structure.

The advancement in science and technology has led to luffa sponge (LS) being widely used as a natural material in industrial application as its polyporous structure and light texture. In order to enhance the utility of LS fibers as the reinforcement of lightweight composite materials, this study investigate its water absorption, mechanical properties, anatomical characteristic and thermal performance. Hence, moisture regain, tensile properties of LS fiber bundles were measured in accordance with standards and the structural characteristics were investigated via microscopic observation. Scanning electron microscopy (SEM) was used to observe the surface morphology and fracture surface of fiber bundles. Test results shows that the special structure where the phloem tissues degenerate to cavities had a significant influence on the mechanical properties of LS fiber bundles. Additionally, the transverse sectional area occupied by fibers in a fiber bundle (SF), wall thickness and ratio of wall to lumen of fiber cell, and crystallinity of cellulose had an impact on the mechanical properties of LS fiber bundles. Furthermore, the fiber bundles density of LS varies range of 385.46-468.70 kg/m³, much less than that of jute (1360.40 kg/m³) and Arenga engleri (950.20 kg/m³) while LS fiber bundles has superior specific modulus.

High-spin states of 192Tl are populated by the heavy ion fusion-evaporation reaction 181Ta(16O, 5n)192Tl at 97 MeV beam energy. A new level scheme with eight new levels is constructed and the level spins are tentatively assigned. The negative-parity yrast band is extended up to 23^{-}\hbar. Subsequently, the systematics of signature splitting and signature inversion are discussed for the negative-parity yrast band of odd-odd Tl isotopes including 192Tl, 194Tl, 196Tl, and 198Tl. With the increase of neutron number signature inversion is found in 196,198Tl at high-spin state in these four Tl isotopes. The reason may be due to the competition between neutron-proton interaction and Coriolis force.

Several coatings configurations of combined aluminizing and diffusion layered aluminide on 316 steel were produced and characterized. These coatings, typically employed as thermal barrier coating (TBC), can also be effective as vibration reduction elements at intermediate and high temperatures. This preliminary work has been focused on the microstructural design and processing effects of the coatings. The damping of the produced specimens was measured up to 450°C and compared with that of the steel substrate. The most performing coatings contain an Al-Si layer and exhibit a steep damping increase above 200 °C, reasonably due to dislocation movements by plastic straining of soft alloy layer and to the interface sliding between layers with different elastic moduli.

A novel starch stabilized Mg/Al LDHs material (S-LDH) was prepared in a facile approach and its fluoride ion removal performance was developed. Characterization of S-LDH was employed by using XRD, FTIR and particle size distribution. The adsorption property was studied through the assessment of adsorption isotherms, kinetic models, thermal dynamics and pH influence. The result shows that a low loading of starch of 10 mg onto LDH could obviously improve fluoride removal rate. The S-LDH had 3 times higher adsorption capacity to fluoride than that of Mg/Al LDH to fluoride. The particle size was smaller and the particle size distribution was narrower for S-LDH than that for Mg/Al LDH. Langmuir adsorption isotherm model and pseudo-second-order kinetic model fitted well with the experimental data. In thermodynamic parameters, the enthalpy (△H0) value was 35.63 kJ mol-1 and the entropy (△S0) value was 0.0806 kJ mol-1K-1. The values of △G0 were negative, implying the adsorption process is spontaneous. S-LDH reveals stable adsorption property in a wide pH range from 3 to 9. The mechanism for fluoride adsorption on S-LDH included surface adsorption and interaction ion exchange.

Background: Molecular genetic events are among the numerous factors affecting the clinical course of papillary thyroid carcinoma (PTC). Recent studies have demonstrated that aberrant expression of miRNA, as well as different thyroid-related genes, correlate with the aggressive clinical course of PTC and unfavorable treatment outcome, which opens up new avenues for using them in personalization of the treatment strategy for patients with PTC. In the present work, our goal was to assess the applicability of molecular markers in preoperative diagnosis of aggressive variants of papillary thyroid cancer. Methods: The molecular genetic profile (expression levels of 34 different markers and BRAF mutation) was studied for 108 cytology specimens collected by fine-needle aspiration biopsy in patients with PTC having different clinical manifestations. Results: Statistically significant differences with adjustment for multiple comparisons (p &lt; 0.0015) for clinically aggressive variants of PTC were obtained for four markers: miRNA-146b, miRNA-221, FN1, and CDKN2A. Weak statistical correlation (0.0015&lt; р&lt;0.05) was observed for miRNA-31, -375, -551b, -148b, -125b, mtDNA, CITED1, TPO, HMGA2, CLU, NIS, SERPINA1, TFF3, and TMPRSS4. Conclusions: The recurrence risk of papillary thyroid carcinoma can be preoperatively predicted using miRNA-221, the fibronectin and cyclin-dependent kinase inhibitor 2A genes.

In recent decades, the requirements for implantable medical devices increased, but the risks of implant rejection still exist. These issues are primarily associated with poor osseointegration, leading to biofilm formation on the implant surface. This study focuses on addressing these issues by developing a biomaterial for implant coatings. 45S5 Bioglass has been widely used in tissue engineering due to its ability to form a hydroxyapatite layer, ensuring a strong bond between the hard tissue and the bioglass. In this context, 45S5 bioglasses, modified by the incorporation of different amounts of copper oxide, from 0 to 8 mol%, were synthesized by the melt-quenching technique. The incorporation of Cu ions does not show a significant change in the glass structure. Since the bioglass exhibited the capacity of being polarized, and therefore promoting the osseointegration effectiveness, the electrical properties of the prepared samples were studied using the impedance spectroscopy method, in the frequency range of 102-106 Hz and temperature range of 200-400 K. The effects of CuO on charge transport mobility were investigated. Additionally, the bioactivity of the modified bioglasses was evaluated through immersion tests in simulated body fluid. The results revealed the initiation of a Ca-P-rich layer formation on the surface within 24 h, indicating the potential of the bioglasses to enhance the bone regeneration process.

This letter presents a dual-frequency terahertz amplitude modulator based on a cross-shaped structure and U-shaped metal patches. Its structural unit is a typical metal-substrate structure. The top metal consists of a cross-shaped structure and U-shaped metal patches, and the bottom substrate layer is made of quartz. Amplitude modulation is achieved by adjusting the temperature of the vanadium dioxide (VO2) patches. The modulation depth can be approximately 75%. The mechanism of the resonance frequency is explained by the equivalent circuit model. The proposed structure shows good amplitude modulation capability at different incidence and azimuth angles by changing the location of the VO2 patches. The dual-frequency terahertz amplitude modulator can be used in terahertz communication, imaging, etc.

The relationship between the structure characteristics and performances of coal based hydrogenation isomeric base oil (CTL) and metallocene catalyzed coal based polyalphaolefin (mPAO) base oil was clarified here. CTL and mPAO were compared with typical petroleum based and natural gas based commercial API Class III and IV base oils. Pressurized differential scanning calorimetry (PDSC), Rotary Bomb Oxidation Test (RBOT) and four-balls friction tester were used to evaluate the oxidation stability and lubrication performance of base oils under different working conditions. The sensitivity of different base oils to typical antioxidants and extreme pressure antiwear agents was compared. Specially, the composition and structure of CTL base oil are obviously different from GTL and mineral base oil. The coal-based CTL and mPAO base oils exhibit commendable viscosity-temperature properties, characteristics, coupled with low-temperature fluidity, fire safety, and minimal evaporation loss. The lubricating properties, oxidation stability and the sensitivity to extreme pressure antiwear agents of CTL are close to those of similar base oils. But the sensitivity of CTL to typical antioxidants is relatively poor. Besides, compared with commercial PAO base oil, mPAO has lower isomerization degree and fewer isomerization types. The oxidation stability and sensitivity to typical antioxidants of mPAO base oil are comparable with those of commercial PAO base oil, while its lubrication performance and sensitivity to typical extreme pressure antiwear agents are significantly better than those of commercial PAO base oil.

To clarify effects of weathered coal humic acid on water-stable aggregates and pore characteristics of reclaimed cambisol, this research analyzed the evolution characteristics of soil aggregates and pores. Effects of different humic acid dosages (0, 1%, 3%, and 5% by weight) and application period (1 year, 2 years, and 3 years) on soil aggregates and organic carbon components in soil water-stable aggregates were investigated. The results showed that water-stable macroaggregates (&gt;0.25 mm) had the highest content in the first year; but in the third year, water-stable microaggregates (0.053–0.25 mm) had the highest content, and silt and clay (&lt;0.053 mm) were at a maximum. In the third year of 5% treatment, mean weight and geometric mean diameters were the largest, soil structure was the most stable, and TOC and water-stable microaggregates (0.053–0.25 mm) in soil had the highest proportions. For 5% treatment, the majority of irregular pores were independent in the first year, and number of pores decreased in the second year, but average pore volume increased, forming robust connected pores. In the third year, the number of elongated and irregular pores increased. In the third year of 5% treatment, most pores were irregular and of size &gt;100 μm, and soil structure was the most stable.

In this paper, the synthesis of two novel luminescent Eu3+ ion complexes [Eu(TFT)3(phen) (1) and Eu(TFT)3(bpy)•Hex (2)] based on the combination of 2-(2,2,2-trifluoroethyl)-1-tetralone (TFT), containing n-donor ligands (1,10-phenanthroline or 2,2'-Bipyridine) and Eu3+ ion is reported herein, and their structural features are discussed on the basis of X-ray crystallographic and thermal analyses. We observed that the ligands transfer energy effectively to the metal center by fluorescence, IR and UV spectrograms studies. The structures and properties of complexes 1-2 were optimized by the DFT theoretical calculation, and the calculation results were consistent with the experimental X-ray structure data and spectral analysis.

The extracellular matrix (ECM) plays a key role as both structural scaffold and regulator of cell signal transduction in tissues. In times of ECM assembly and turnover, cells upregulate assembly of the ECM protein, fibronectin (FN). FN is assembled by cells into viscoelastic fibrils that can bind upward of 40 distinct growth factors and cytokines. These fibrils play a key role in assembling a provisional ECM during embryonic development and wound healing. Fibril assembly is also often upregulated during disease states, including cancer and fibrotic diseases. FN fibrils have unique mechanical properties, which allow them to alter mechanotransduction signals sensed and relayed by cells. Binding of soluble growth factors to FN fibrils alters signal transduction from these proteins, while binding of other ECM proteins, including collagens, elastins, and proteoglycans, to FN fibrils facilitates the maturation and tissue specificity of the ECM. In this review, we will discuss the assembly of FN fibrils from individual FN molecules; the composition, structure, and mechanics of FN fibrils; the interaction of FN fibrils with other ECM proteins and growth factors; the role of FN in transmitting mechanobiology signaling events; and approaches for studying the mechanics of FN fibrils.

Most of the mid-high permeability sandstone oilfields in China have entered the ultra-high water cut stage, accompanied with the highly-dispersed residual oil, and the control effect of mi-cro-heterogeneity on the residual oil is increasingly prominent. Understanding the microscopic characteristics of pore structural and its evolution during the long-term waterflooding is critical for enhancing the accuracy and efficiency of oil field exploitation. While the previous insights paid more attention to the geometrical and morphological features of pore structure and ignores the relation of pore structure with the fluid flow capacity. In this study, we propose a microscopic pore structure classification method considering pore size and local permeable capacity, which realizes the physical classification and quantitative evaluation of pore structure characteristics for different permeability rocks. The micro-pore structure is classified into 6 types based on the key evaluation parameters of pore diameter and flow flux area. By taking six mid-high permea-bility sandstone core samples from Daqing oilfield in China, a series of long-term waterflooding experiments are carried out and the interior pore structure was captured using high precision CT scanning technique. The results reveals that high-permeability reservoirs exhibit concentrated pores diameters and finer throats, whereas mid-permeability reservoirs exhibit smaller pores and throats in greater quantity. With the increase of water injection volumes, the permeable ca-pacity and connectivity of the high-connectivity pore space in ultra-high- and high-permeability reservoirs are enhanced, and in mid-permeability reservoirs, the micro-heterogeneity intensifies the increase in low-connectivity small pores. These findings provide new insights for the micro-scopic heterogeneity and a solid theoretical basis for investigating the occurrence of microscopic residual oil and optimising enhanced oil recovery strategies at the late stage of ultra-high water cut.

Modern Monte-Carlo-based rendering systems still suffer from the computational complexity involved in the generation of noise-free images, making it challenging to synthesize interactive previews. We present a framework suited for rendering such previews of static scenes using a caching technique that builds upon a linkless octree. Our approach allows for memory-efficient storage and constant-time lookup to cache diffuse illumination at multiple hitpoints along the traced paths. Non-diffuse surfaces are dealt with in a hybrid way in order to reconstruct view-dependent illumination while maintaining interactive frame rates. By evaluating the visual fidelity against ground truth sequences and by benchmarking, we show that our approach compares well to low-noise path traced results, but with a greatly reduced computational complexity allowing for interactive frame rates. This way, our caching technique provides a useful tool for global illumination previews and multi-view rendering.

To eliminate the influence of the inconsistency on the cycle life and the available capacity of the battery pack, and improve the balancing speed, a novel inductor-based layered bidirectional equalizer (IBLBE) is proposed. The equalizer is composed of the bottom balancing circuits and the upper balancing circuits, and the two layer circuits both consist of a plurality of balancing sub-circuits, which allow the dynamic adjustment of equalization path and equalization threshold. The battery string is modularized by layered balancing circuits to realize fast active equalization, especially for long battery strings. By controlling the bottom balancing circuits, the individual cells can be balanced in each module. At the same time, the equalization between battery modules can be realized by controlling the upper balancing circuits. Simulation and experimental results demonstrate that the proposed equalizer can achieve fast active equalization for a long battery string, and has the characteristics of multi balancing path, large balancing current and high accuracy. The advantages of the proposed equalizer are further verified by a comparison with existing active equalizer.

This article introduces a novel payload structure, which has been experimentally proven to have smaller impact force while the carried internal electronics remains intact. The study describes in details how materials and geometric structures were chosen based on information analysis. It is clarified how possible geometric structures and materials can be chosen to yield optimal efficiency. Finite element method simulations were carried out to investigate the mechanical properties of several geometric structures, which has led to the dodecahedron form. For the frame, Polylactic Acid were chosen as an optimal material. A low air pressure test for parts of the structure, and also the whole structure were carried out with successful results. Drop tests, with force measuring sensors and high speed videos, were carried out for measuring and comparing the maximal impact force of classical payloads and the novel one. Laboratory and real life tests demonstrated that the developed new structure is safer and it is applicable.

Arabinoxylans (AXs) are non-starch polysaccharides with complex structures naturally occurring in grains (i.e., barley, corn, and others) providing many health benefits, especially as prebiotics. AXs can be classified as water-extractable (WEAX) and water-unextractable (WUAX) based on their solubility, with properties influenced by grain sources and extraction methods. A large body of evidence shows that AXs exert an im-portant health impact, including glucose and lipid metabolism regulation and immune system enhancement, which is induced by the interactions between AXs and the gut microbiota. Recent research underscores the dependence of AX physiological effects on structure, advocating for a deeper understanding of struc-ture-activity relationships. While systematic studies on WEAX are prevalent, knowledge gaps persist re-garding WUAX, despite its higher grain abundance. Thus, this review reports recent data on WUAX struc-tural properties (chemical structure, branching, MW) in cereals under different treatments. It discusses WUAX applications in baking and its benefits deriving from gut fermentation.

Leakage is important in groundwater cycle research and water resource management, the key is to construct the spatial distribution of aquitard. Influenced by natural and anthropogenic factors, the density of boreholes restricts the accuracy of aquitard structure. This paper explores the K-Nearest Neighbor (KNN) method to construct multi-layer aquitard structure in the hinterland of Songnen Plain, Northeast China, with limited boreholes, and compare it with Inverse Distance Weight (IDW) and Ordinary Kriging (OK) methods to evaluate the leakage. The KNN needs to first identify the eigenvalue-k of each layer, which is used to enhance the trainset to obtain the testset with a larger amount of sample data enhanced, and to make a prediction to obtain the 3-dimensional structure of aquitard. KNN is more accurate than the IDW and OK. The aquitrad structure obtained by the KNN is different from the IDW and OK, the thickness difference is 3.53%-54.00%, the area difference is 2.28%-23.91%, and the difference in leakage can be up to 24.51%. KNN also has a high degree of identification of aquitard edges, which can help the prevention of groundwater pollution. The results provide guidance for water balance analysis, borehole engineering design, water resources management and exploitation.

Ion current rectification (ICR) is the ratio of ion current by forward bias to by backward bias and is a critical indicator of diode performance. In previous studies, many attempts have been continued to improve the performance of this ICR, but there is the intrinsic problem for geometric changes that induce ionic rectification due to their fabrication problem. Additionally, the high ICR could be achieved in the narrow salt concentration range only. Here, we propose a multi-layered bipolar ionic diode based on an asymmetric nanochannel network membrane (NCNM), which is realized by soft lithography and self-assembly of homogenous-sized nanoparticles. Owing to the freely changeable geometry based on soft lithography, the ICR performance can be explored according to the variation of microchannel shape. Interestingly, very stable ICR performance can be achieved using the multi-layered 3D configuration for the bipolar diode in a broad range of salt concentrations (0.1mM ~ 100 mM). This demonstrates the promising potential of multi-layered NCNM for applications in highly concentrated electrolytes, such as biosensors, desalination, or energy harvesting.

The corrugated board packaging industry is increasingly using advanced numerical tools to design and estimate the load capacity of its products. That is why numerical analyzes are becoming a common standard in this branch of manufacturing. Such trend causes either the use of advanced computational models that take into account the full 3D geometry of the flat and wavy layers of corrugated board, or the use of homogenization techniques to simplify the numerical model. The article presents theoretical considerations that extend the numerical homogenization technique already presented in our previous work. The proposed here homogenization procedure also takes into account the creasing and / or perforation of corrugated board, i.e. processes that undoubtedly weaken the stiffness and strength of the corrugated board locally. However, it is not always easy to estimate how exactly these processes affect the bending or torsional stiffness. What is known for sure is that the degradation of stiffness depends, among other things, on the type of cut, its shape, the depth of creasing, as well as their position or direction in relation to the corrugation direction. The method proposed here can be successfully applied to model smeared degradation in a finite element or to define degraded interface stiffnesses on a crease line or a perforation line.

Pore structure characterization and fractal analysis have great significance for understanding and evaluating tight limestone reservoirs. In this work, the pore structure of tight limestone is characterized combined with low-temperature nitrogen adsorption (LTNA) and low-field nuclear magnetic resonance (NMR), and the fractal dimension of tight limestone pore structure is discussed based on LTNA and NMR data. The results indicate that the pores of tight limestone have H3 and H4 types, the pore size distribution (PSD) of H3 type is a wave distribution ranging from 2 to 10 nm, and the PSD of H4 type is a unimodal distribution ranging from 2 to 10 nm. The transverse relaxation time (T2) spectrum of tight limestone shows single peak (DF), double peak (SF) and three peak (TF), and the T2 spectrums for micropores, mesopores and macropores range from 0.1 to 10 ms, from 10 to 100 ms, and greater than 100 ms, respectively. The LTNA fractal dimension of tight limestone (DL) ranges between 2.4446 and 2.7688, with an average of 2.5729, and the NMR fractal dimensions of micropores (DNMR1), mesopores (DNMR2) and macropores (DNMR3) are distributed between 0.3744 to 1.1293, 2.4263 to 2.9395 and 2.6582 to 2.9989, respectively. Moreover, there is no correlation between fractal dimension and permeability and porosity, a negative correlation between DL and average pore radius, a positive correlation between DL and specific surface area, and a positive correlation between DNMR2 and DNMR3 and micropore content, while DNMR2 and DNMR3 are negatively correlated with the content of mesopores and macropores.

Ni-rich layered cathodes are regarded as a potential candidate for high energy-density lithium-ion batteries, but their high sensitivity to air during storage and poor thermal stability are a vital challenge for large-scale applications. In this paper, an effective solid-solution strategy was proposed to improve the surface and structural stability of Ni-rich layered cathodes by introducing Li2MnO3. The structural analysis results indicate that the formation of Li2CO3 inert layers on Ni-rich layered cathodes during storage in air is responsible for the increased electrode interfacial impedance, thereby resulting in the severe deterioration of electrochemical performance. The introduction of Li2MnO3 can reduce the surface reactivity of Ni-rich cathode materials, playing a certain suppression effect on the formation of surface Li2CO3 layer and the deterioration of electrochemical performances. Additionally, the thermal analysis results show that the heat release of Ni-rich cathodes strongly depends on the charge of states, and Li2MnO3 can suppress oxygen release and significantly improves the thermal stability of Ni-rich layered cathodes. This work provide a method to improve the storage performance and thermal stability of Ni-rich cathode materials.

New hybrid composites based on the inclusion of a vegetal extract, i.e., Boswellia Serrata extract (BSE), rich in boswellic acids, well known as a potent anti-inflammatory natural drug, in a lamellar solid layered double hydroxide (LDH), i.e. a Magnesium Aluminum Carbonate, were developed and characterized in the present work. The adopted LDH exhibits a layered crystal structure, comprised of positively charged hydroxide layers and interlayers composed of carbonate anions and water molecules, thus it was expected to embed negatively charged boswellic acids. In the present case, a calcination process was also adopted on LDH to increase organic acids loading, based on the replacement of original inorganic anions. An accurate investigation was carried out by TGA, PXRD, FT-IR/ATR, XPS and LC-MS to ascertain the nature, interaction, and quantifica-tion of the active molecules of the vegetal extract loaded in the developed hybrid materials. As a result, a significant disruption of the original layered structure was observed in LDH subjected to calcination (LDHc), and this material was able to include a higher amount of organic acids when its composite with BSE was prepared. However, in vitro tests on composites bioactivity, expressed in terms of antimicrobial and anti-inflammatory activity, evidenced LDH-BSE as a better material compared to BSE and to LDHc-BSE, thus suggesting that, though the embedded organic acids amount was lower, they could be more available since not firmly bound to the clay. The composite was able to significantly decrease the number of viable pathogens such as Escherichia Coli and Staphylococcus aureus, as well as the internalization of toxic active species into human cells imposed to oxidative stress in comparison to the BSE.

By solving a Marchenko equation, Green's functions at an arbitrary (inner) depth level inside an unknown elastic layered medium can be retrieved from single-sided reflection data, which are to be collected at the top of the medium. So far, an exact solution could only be obtained if the medium obeys stringent monotonicity conditions and if all forward-scattered (non-converted and converted) transmissions between the acquisition level and the inner depth level are known a-priori. We introduce an alternative Marchenko equation by revising the window operators that are applied in its derivation. We also introduce an auxiliary equation for transmission data, which are to be collected at the bottom of the medium, and a coupled equation, which is based on both reflection and transmission data. We show that the joint system of the Marchenko equation, the auxiliary equation and the coupled equation can be succesfully inverted when broadband reflection and transmission data are available. This results in a novel methodology for elastodynamic Green's function retrieval from two-sided data. Apart from these data, our approach requires P- and S-wave transmission times between the inner depth level and the top of the medium, as well as two angle-dependent amplitude scaling factors, which can be estimated from the data by enforcing energy conservation.

Broadband noise reduction over the low-mid frequency range in the building and transportation sectors requires compact lightweight sound absorbers of typical sub-wavelength size. The use of multi-layered closely-spaced (micro-)perforated membranes or panels, if suitably optimized, contribute to these objectives. However, their elasticity or modal behaviors often impede the final acoustical performance of the partition. The objective of this study is to get insights into the vibrational effects induced by elastic limp membranes or panels volumetric modes on the optimized sound absorption properties of acoustic fishnets and functionally-graded partitions (FGP). Cost-efficient global optimization of the partition total frequency-averaged dissipation is achieved from simulated annealing with vibrational effects included through an impedance translation method. Critical coupling analysis reveals how the membranes or panels vibrations redistribute the locations of the Hole-Cavity resonances as well as their cross-coupling with the panels first volumetric mode. It is found that elastic limp micro-perforated membranes broaden the first pass-band of acoustic fishnets while smoothing out the dissipation ripples over the FGP optimiza-tion bandwidth. Moreover, the resonance frequency of the first panels mode sets an upper limit to the broadband optimization of FGPs, up to which high dissipation, low reflection and low trans-mission can be achieved.

We investigated layered titanium nitride (TiN) and aluminum nitride (AlN) for color glasses in Building Integrated Photovoltaic (BIPV) systems. AlN and TiN are among suitable and cost-effective optical materials to be used as thin multilayer films, owing to the significant difference in their refractive index. To fabricate the structure, we used radio frequency magnetron deposition method to achieve the target thickness uniformly. A simple, fast, and cheap fabrication method is achieved by depositing the multilayer films in a single sputtering chamber. It is demonstrated that a multilayer stack that allows light to move from a low refractive index layer to a high refractive index layer or vice-versa can effectively create various distinct color reflections for different film thicknesses and multilayer structures. It is investigated from simulation based on wave optics that, TiN/AlN multilayer offers better color design freedom and cheaper fabrication process as compared to AlN/TiN multilayer films. Blue, green, and yellow color glasses with optical transmittance of more than 80% was achieved by ITO coated glass/TiN/AlN multilayer films. This technology exhibits good potential in commercial BIPV system applications.

Although promoting healthy eating is a policy objective, the controllability of dietary habits remains uncertain. The personal dietary patterns reflect many factors, of which some are relatively controllable for individual, and others are not. In this article, assuming that some sort of information about controllability of dietary habits is contained in the observed pattern of food consumptions, we focused on dietary pattern on its own. We introduced a statistical descriptive model for data on food frequency questionnaire, estimated strength of pairwise linkage between foodstuffs, and grouped foodstuffs by applying community detection to the networks of the estimated inter-food linkages. Those linkages represent co-movement of pairs of foods consumption. Furthermore, we demonstrated an analysis on the relationship between health of mind and dietary habits considering the aspect of controllability of dietary habits. Using an observational study in Japan, we obtained the following results: 115 foodstuffs were divided into 3 groups for both of genders, but the compositions were different by gender; in the analysis of mental health, some stress response items were associated with the dependence on some of those food groupings. As the grouping of foodstuffs based on our estimation depicted the internal structure of dietary habit that a healthy eating policy should regard as constraint, it follows that we should design the policy along the line with that grouping.

As the most active plateau on the Earth, the Qinghai-Tibet Plateau has a complex crust-mantle structure. Knowledge of the distribution of such a structure provides information for understanding the underlying geodynamic processes. We obtains a three-dimensional density model of crustal and upper mantle beneath Qinghai-Tibet plateau and its surrounding areas from the residual geoid anomalies using the Earth Gravitational Model (EGM) 2008. We estimate a refined density model by iterations, using an initial density contrast model. We confirm that the EGM2008 mission products can be used to constrain the crust-mantle density structures. Our major findings are: (1). At 300-400 km depth, high-D anomalies terminate around Jinsha River Suture (JRS) in the central TP, suggesting that the Indian plate has been reached over the Bangong Nujiang Suture (BNS) and almost reach to the JRS. (2). On the eastern TP, low-D anomalies at the depth of 0-300 km together with high-D anomalies at 400-670 km further verified the current eastward subduction of Indian plate. The ongoing subduction provides forces to the occurrences of frequent earthquakes and volcano. (3). At 600 km depth, low-D anomalies inside the TP illustrate the existence of hot weak material beneath there, contributing to the external material inward-thrusting.

Lithium-rich layered oxides is one of the most perspective candidates for cathode materials of lithium ion battery, because of its high discharge capacity. However, there are some disadvantages of uneven composition, voltage decay, and poor rate capacity, which are closely related to the preparation method. Here, 0.5Li2MnO3·0.5LiMn0.8Ni0.1Co0.1O2 were successfully prepared by sol-gel and oxalate co-precipitation methods. A systematic analysis of the materials shows that the 0.5Li2MnO3·0.5LiMn0.8Ni0.1Co0.1O2 prepared by the oxalic acid co-precipitation method has the most stable layered structure and the best electrochemical performance. The initial discharge specific capacity is 261.6 mAh·g-1 at 0.05 C, and the discharge specific capacity is 138 mAh·g-1 at 5 C. The voltage decay is only 210 mV, and the capacity retention is 94.2% after 100 cycles at 1 C. The suppression of voltage decay can be attributed to the high nickel content and uniform element distribution. In addition, tightly packed porous spheres help to reduce lithium ion diffusion energy and improve the stability of the layered structure, thereby improving cycle stability and rate capacity. This conclusion provides a reference for designing high energy density lithium-ion batteries.

In the extra-thick coal seams and multi-layered hard roofs, the longwall hydraulic support yielding, coal face spalling, strong deformations of goaf-side entry, and severe ground pressure dynamic events typically occur at the longwall top coal caving longwall faces. Based on the Key strata theory an overburden caving model is proposed here to predict the multilayered hard strata behaviour. The proposed model together with the measured stress changes in coal seam and underground observations in Tongxin coal mine provides a new idea to analyse stress changes in coal and help to minimise rock bursts in the multi-layered hard rock ground. Using the proposed primary Key and the sub-Key strata units the model predicts the formation and instability of the overlying strata that leads to abrupt dynamic changes to the surrounding rock stress. The data obtained from the vertical stress monitoring in the 38 m wide coal pillar located adjacent to the longwall face indicates that the Key strata layers have a significant influence on ground behaviour. Sudden dynamically driven unloading of strata was caused by the first caving of the sub-Key strata while reloading of the vertical stress occurred when the goaf overhang of the sub-Key strata failed. Based on this findings several measures were recommended to minimise the undesirable dynamic occurrences including pre-split of the hard Key strata by blasting and using the energy consumption yielding reinforcement to support the damage prone gate road areas. Use of the numerical modelling simulations was suggested to improve the key theory accuracy.

Capital structure decision plays an imperative role in firm’s performance. Recognizing the importance, there has been many studies inspected the rapport of capital structure with performance of firms and findings of those studies are inconclusive. In addition, there is relative deficiency of empirical studies examining the link of capital structure with performance of banks in Bangladesh. This paper attempted to fill this gap. Using panel data of 22 banks for the period of 2005-2014, this study empirically examined the impacts of capital structure on the performance of Bangladeshi banks assessed by return on equity, return on assets and earnings per share. Results from pooled ordinary least square analysis show that there are inverse impacts of capital structure on bank’s performance. Empirical findings of this study is of greater significance for the developing countries like Bangladesh because it will call upon concentration of the bank management and policy makers to pursue such policies to reduce reliance on debt and to accomplish optimal level capital structure. This research also contributes to empirical literatures by reconfirming (or otherwise) findings of previous studies.

Few studies have examined the dietary protein intake and sources in combination with the longitudinal changes in brain structure markers. Our study aimed to examine the association between dietary protein intake and different sources of dietary protein with the longitudinal rate of change in brain structural markers. A total of 2723 and 2679 participants from the UK Biobank were included in the analysis. The relative and absolute amounts of dietary protein intake were calculated through a 24-hour dietary recall questionnaire. The longitudinal change rates of brain structural biomarkers were computed using two waves of brain imaging data. We utilized multiple linear regression to examine the association between dietary protein and different sources and the longitudinal changes in brain structural biomarkers. Restrictive cubic splines were used to explore nonlinear relationships, and stratified and sensitivity analyses were conducted. Increasing the proportion of animal protein in dietary protein intake is associated with a slower reduction in the total hippocampus volume (THV, β: -0.02524, P&lt;0.05), left hippocampus volume (LHV, β: -0.02435, P&lt;0.01) and right hippocampus volume (RHV, β: -0.02544, P&lt;0.05).Higher intake of animal protein relative to plant protein is linked to a lower atrophy rate in THV (β: -0.01249, P&lt;0.05) and LHV (β: -0.01173, P&lt;0.05) and RHV (β: -0.01193, P&lt;0.05). Individuals with higher intake of seafood exhibit lower longitudinal rate of change in HV compared to those with no consume (THV, β: -0.004514; P&lt;0.05; RHV, β: -0.005527, P&lt;0.05). In subgroup and sensitivity analyses, there was not a significantly alteration. A moderate increase in the intake and proportion of animal protein in the diet, especially from seafood, is associated with a lower longitudinal change rate in hippocampus volume.

GABAA receptors are channel proteins crucial to mediating neuronal balance in the CNS. The structure of GABAA receptors allows for multiple binding sites and is key to drug development. Yet, the formation mechanism of the receptor’s distinctive pentameric structure is still unknown. This study aims to investigate the role of three predominant subunits of the human GABAA receptor in the formation of protein pentamers. Through purifying and refolding the protein fragments of the GABAA receptor α1, β2, and γ2 subunits, homopentamers were visualised with negative staining and Cryo-EM. To aid the analysis, AlphaFold2 was used to compare the structures. Results show that α1 and β2 subunit fragments successfully formed homo-oligomers, particularly homopentameric structures, while the predominant heteropentameric GABAA receptor was also replicated through the combination of the three subunits. However, it is still unclear whether γ2 subunits can form homopentamers or their main purpose is to bring together the α1 and β2 subunits to form GABAA receptors. Nevertheless, this study will lead to a deeper understanding of the atomic structure of GABAA receptors, especially in the formation mechanism of complex protein structures, and hopefully pave the way to the development of novel therapeutics for neuropsychiatric diseases.

In this paper, MgAl Layered double hydroxides (LDH) were synthesized by co-precipitation method using a colloid mill and characterized by XRD, IR and SEM. The LDHs was repeatedly tested and compared with different bearing lifetime tester in lithium base grease, and it was found that the environmental-friendly LDHs had greater performance than the traditional antioxidant, and it was the development direction of a new generation of environmental-friendly antioxidants in the future. By adding LDHs into large electric shovel greats (GRK-A) in open-pit coal mine, it can be seen by PDSC evaluation that the service lifetime of grease is extended by 20% while the overall performance of grease is not affected. With the increase of LDHs addition, the grease sample gets the greater activation energy, the stronger thermal oxidation and decomposition resistance. Comparing the energy storage modulus and flow transition index at different temperatures, it can be seen that adding the right amount of LDHs needs close attention for the system oxidation resistance and viscoelasticity. For the electric shovel grease system, the best oxidation resistance and rheological properties can be achieved by adding 2% of LDHs. The rheological viscosity-temperature curves show that the grease samples with different ratios of solid LDHs have better low-temperature properties than the mine grease.

The main objective of this study focuses on designing and testing body protection systems using advanced materials based on aramid fibers, for high impact speeds of up to 410...430 m/s. The investigation of the failure mechanisms identifies issues of protective materials, major challenges and technological problems for efficient development of these systems. The authors presents an investigation on the failure processes and destructive stages of a ballistic package made of succesive layers of LFT SB1plus, taking into account the particular test conditions from NIJ Standard-0101.06 Ballistic Resistance of Body Armor. The main parameter of interest was the backface signature (BFS), but also details of projectile arrest and SEM investigaton could offer arguments in using this material for individual protection.

A graphene-containing LDH was prepared by re-hydration of the oxides produced by the calcination of an organic LDH. While the memory effect is a widely recognized effect on oxides produced by inorganic LDHs, it is unprecedented from the calcination/re-hydration of organic ones. Different temperatures (400, 600 and 1100 °C) were tested, on the basis of thermogravimetric data. Water instead of a carbonate solution was used for the re-hydration, with CO₂ available from water itself and/or air to induce a slower process with an easier and better intercalation of the carbonaceous species within the layers. The samples were characterized by X-ray Powder Diffraction (XRPD), IR and Raman spectroscopy and scanning electron microscopy (SEM). XRPD indicate the presence of carbonate LDH mixed with a layered phase with a larger d-spacing. IR confirmed that the prevailing anion is carbonate, coming from the water used for the re-hydration and/or air. Raman data indicated the presence of low-ordered graphenic species moieties and SEM the absence of separated graphene of graphitic sheets, suggesting an intimate mixing of the carbonaceous phase with reconstructed LDH. Organic LDHs gave better memory effect after calcination at 400 °C. Conversely, the graphenic species are observed after rehydration of the sample calcined at 600 °C with a reduced memory effect, demonstrating the interference of the carbonaceous phase with LDH reconstruction and the bonding with LDH layers to form a graphene-LDH nanocomposite.

The independent set, IS, on a graph $G=(V,E)$ is $V^{*}\subseteq V$ such that no two vertices in $V^{*}$ have an edge between them. The MIS problem on G seeks to identify an IS with maximum cardinality, i.e. MIS. $V^{*}\subseteq V$ is a vertex cover, i.e. VC of $G=(V,E)$ if every $e\in E$ is incident upon at least one vertex in $V^{*}$ . $V^{*}\subseteq V$ is dominating set, DS, of $G=(V,E)$ if $\forall v\in V$ either $v\in V^{*}$ or $\exists u\in V^{*}$ and $(u,v)\in E$ . The MVC problem on G seeks to identify a vertex cover with minimum cardinality, i.e. MVC. Likewise, MCV seeks a connected vertex cover, i.e. VC which forms one component in G, with minimum cardinality, i.e. MCV. A connected DS, CDS, is a DS that forms a connected component in G. The problems MDS and MCD seek to identify a DS and a connected DS i.e. CDS respectively with minimum cardinalities. MIS, MVC, MDS, MCV and MCD on a general graph are known to be NP-complete. Polynomial time algorithms are known for bipartite graphs, chordal graphs, cycle graphs, comparability graphs, claw-free graphs, interval graphs and circular arc graphs for some of these problems. We introduce a novel graph class, layered graph, where each layer refers to a subgraph containing at most some k vertices. Inter layer edges are restricted to the vertices in adjacent layers. We show that if $k=\Theta (log\mid V\mid )$ then MIS, MVC and MDS can be computed in polynomial time and if $k=O\left({(log\mid V\mid )}^{\alpha }\right)$ , where $\alpha <1$ , then MCV and MCD can be computed in polynomial time. If $k=\Theta \left({(log\mid V\mid )}^{1+ϵ}\right)$ , for $ϵ>0$ , then MIS, MVC and MDS require quasi-polynomial time. If $k=\Theta (log\mid V\mid )$ then MCV, MCD require quasi-polynomial time. Layered graphs do have constraints such as bipartiteness, planarity and acyclicity.

A series of MgAl-layered double hydroxide (MgAl-HT), the calcined form at 500^oC (MgAlO_x) and the re-hydrated one at 25^oC (MgAl-HT-RH) were synthesized. Physicochemical properties of the catalysts were characterized by x-ray diffraction (XRD), scanning electron microscopy (SEM). Surface area of the as-synthesized, calcined and re-hydrated catalysts was determined by N₂ physisorption at -196^oC. CO₂-teperature programmed desorption (CO₂-TPD) was applied to determine the basic sites of catalysts. The catalytic test reaction was carried out using benzaldehyde and their derivatives with nitromethane and their derivatives. The Henry products (1-15) were obtained in a very good yield using MgAl-HT-RH catalyst either by conventional method at 90^oC in liquid phase, or under microwave irradiation method. The mesoporous structure and basic nature of re-hydrated solid catalyst were responsible for their superior catalytic efficiency. The robust nature was determined by using the same catalyst for five times, where the product % yield was almost unchanged significantly.

The development of printing technologies has enabled the realization of electric circuit fabrication on flexible substrate. However, the current technique remains restricted to single-layer patterning. In this paper, we demonstrate a fully solution-processable patterning approach for multi-layer circuits using a combined method of laser sintering and ablation. Selective laser sintering of silver (Ag) nanoparticle-based ink is applied to make conductive patterns on a heat-sensitive substrate and insulating layer. The laser beam path and irradiation fluence are controlled to create circuit patterns for flexible electronics. Microvia drilling using femtosecond laser through the polyvinylphenol-film insulating layer by laser ablation, as well as sequential coating of Ag ink and laser sintering, achieves an interlayer interconnection between multi-layer circuits. The dimension of microvia is determined by a sophisticated adjustment of laser focal position and intensity. Based on these methods, the flexible electronic circuit with chip-size-package light-emitting diodes was successfully fabricated and demonstrated with functional operations.

We report the growth of graphene at a low temperature using the cold wall chemical vapor deposition technique (CWCVD). Few layered (~6-8 layers) graphene were grown on nickel-coated silicon with acetylene as the precursor gas. The advantage of the combination of the acetylene (as a carbon feedstock) and the nickel catalyst was the lowering of the graphene growth temperature. Nickel coated silicon samples were pre-treated (heat treatment in inert atmosphere) before the growth and the effect of the pre-treatment on the catalyst as well as on the grown film was studied. The final samples were characterized with scanning electron microscopy and Raman spectroscopy. In CWCVD route, the heating of only the substrate holder enabled high heating and cooling rates, which, along with the control over partial pressure of the precursor gas had profound effect on the formation of graphene. In the best sample we have achieved almost equal intensity of the G and 2D peaks in Raman spectrum, which implied about ~6-8 layers of Graphene. The defect peak (the D band) was extremely small in the sample and it was attributed to the ripples and the underlying roughness of the nickel film. We analyzed that a proper choice of the thickness of catalyst layer and a higher cooling rate after graphene growth it would be possible to obtain monolayered graphene. Similar samples grown in a normal atmospheric CVD (with some engineered design to promote fast cooling) were also compared with the cold wall CVD grown samples and plasma assisted CWCVD, and cold-wall CVD demonstrated a better control over the quality of graphene film through the fast cooling and a controlled partial pressure of the precursor gas.

This study focuses on examining the determinants of capital structure and the influence of taxes within Iran Khodro Company in the automobile industry from 2016 to 2023. The research analyzes the relationship between debt, taxes, and various company-specific factors. Findings indicate a direct relationship between taxes and debt, with financial leverage being the most significant element related to taxes. The study aims to provide valuable insights for managers and decision-makers in enhancing financial decision-making and shareholder wealth. Various studies have also been conducted on the impact of taxes and different factors on the capital structure of companies listed on the Tehran Stock Exchange, highlighting the importance of tax implications in financial decisions.

Dengue (DENV) and Zika (ZIKV) virus continue to pose significant challenges globally due to their widespread prevalence and severe health implications. Given the absence of effective vaccines and specific therapeutics, targeting of the highly conserved NS5 RNA-dependent RNA polymerase (RdRp) domain has emerged as a promising strategy. However, limited efforts have been made to develop inhibitors for this crucial target. In this study, we employed an integrated in silico approach utilizing combinatorial chemistry, docking, molecular dynamics simulations, MM/GBSA, and ADMET studies to target the allosteric N-pocket of DENV3-RdRp and ZIKV-RdRp. Using this methodology, we designed lycorine analogs with natural S-enantiomers (LYCS) and R-enantiomers (LYCR) as potential inhibitors of non-structural protein 5 (NS5) in DENV3 and ZIKV. Notably, 12 lycorine analogs displayed a robust binding free energy (&lt;-9.00 kcal/mol), surpassing that of RdRp-Ribavirin (&lt;-7.00 kcal/mol) along with promising ADMET score predictions (&lt;4.00), of which (LYCR728-210, LYCS728-210, LYCR728-212, LYCS505-214) displayed binding properties to both DENV3 and ZIKV targets. This study highlights the potential of non-nucleoside lycorine-based analogs with different enantiomers that may present different or even completely opposite metabolic, toxicological, and pharmacological profiles as promising candidates for inhibiting NS5-RdRp in ZIKV and DENV3, paving the way for further exploration for the development of effective antiviral agents.

MoS₂/TiO₂ nanostructures made of MoS₂ nanoparticles covering TiO₂ nanosheets have been synthesized, either via ex-situ or in-situ approaches. Morphology and structure of MoS₂/TiO₂ hybrid nanostructures have been investigated and imaged by means of X-ray diffraction (XRD) analysis and high-resolution transmission electron microscopy (HRTEM), while the vibrational and the optical properties have been investigated by Raman, Fourier-transform infrared spectroscopy (FTIR) and UV−visible (UV-Vis) techniques. The different stacking degrees together with the size distribution of the MoS₂ nanosheets, decorating the TiO₂ nanosheets, have been carefully obtained from HRTEM images. The nature of the surface sites on the main exposed faces of both materials has been detected by means of in-situ FTIR spectra of adsorbed CO probe molecule. The results coming from the ex-situ and in-situ approaches will be compared, by highlighting the role of the synthesis processes in affecting morphology and structure of MoS₂ nanosheets, including their curvature, surface defects, and stacking order. Some more, it will be shown that the in-situ approach is affecting the reactivity of the TiO₂ nanosheets too, hence in turn affects the MoS₂/TiO₂ nanosheets interaction.

Biocompatible and biodegradable poly(butylene succinate-co-adipate) (PBSA)/hexadecylamine-modified PPZn (m-PPZn) nanocomposites were prepared using a melt mixing process. Experimental results of wide-angle X-ray diffraction and transmission electron microscopy revealed that the stacking layers of the m-PPZn were partially intercalated and partially exfoliated into the PBSA polymer matrix. The isothermal crystallization kinetics of PBSA/m-PPZn nanocomposites were studied at the temperature range of 62−70 °C and the half-time for crystallization of 3 wt % PBSA/m-PPZn nanocomposite was reduced by 27−35% compared with that of pure PBSA. This finding suggests that the incorporation of m-PPZn might cause the heterogeneous nucleation and the subsequent crystallization growth, which enhances the isothermal crystallization rate of PBSA/m-PPZn nanocomposite. The biodegradation rates of PBSA using Lipase from Pseudomonas sp. increase as the contents of m-PPZn increase. The degradation behavior of the neat PBSA investigated using the change of weight-average molecular weight belongs to exo-type hydrolysis activity. It is necessary to point out that the change of degree of crystallinity and degradation rate are almost linearly proportional to the loading of hexadecylamine-modified PPZn. This finding would provide an important information for the manufacturing biodegradable PBSA nanocomposites.

Layered halide perovskites have emerged as a promising contender in solid-state lighting thanks to their tunable bandgap, high luminescence quantum yield, and high color purity. However, the fabrication of perovskite light-emitting devices in laboratories usually experiences low de-vice-to-device reproducibility since perovskite crystallization is highly sensitive to ambient condi-tions, such as humidity and temperature. Although device processing inside gloveboxes is primarily used to reduce the influence of oxygen and moisture, several extraneous variables, including gas-eous pollution traces and thermal fluctuations in the inert atmosphere or contaminations from re-sidual solvents confined in the enclosed environment, can destabilize the crystallization process and alter the properties of the emissive layers. Here, we examine different experimental set-ups for spin-coating deposition of layered perovskites in inert atmospheres and their influences on the formation of polycrystalline thin films. Our results demonstrate that fluctuations in the glovebox properties (concentrations of residual O2 and H2O or solvent traces), even in very short timescales, can negatively impact the consistency of the perovskite film formation, while thermal variation plays a relatively minor role in this phenomenon. Furthermore, careful storage of chemical species inside the workstation is critical for reproducing high-quality perovskite layers. Consequently, when applying our most controlled environment for perovskite deposition, the photoluminescence life-time of perovskite thin films shows a standard deviation of only 3%, whereas the reference set-up yields a 15% standard deviation. Regarding complete perovskite light-emitting diodes, the uncer-tainties in statistical luminance and EQE data are significantly reduced from 230% and 140% to 38% and 42%, respectively.

Layered double hydroxides (LDHs) have emerged as promising catalysts for various acid-base catalytic reactions. Due to their unique structure and regulatable dual acid-base properties, they offer more environmentally friendly and sustainable alternatives to traditional liquid acid and base catalysts. This study introduces the structural composition, preparation methods, and acid-base catalytic properties of LDHs-based catalysts. Recent application progress of LDHs and rehydrated LDHs, LDHs-based metal nanocatalysts, and LDHs-based mixed metal oxide catalysts used as solid acid-base catalysts in acid-base green catalytic conversion is reviewed. The challenges and prospects of LDHs-based catalysts as green and sustainable catalysts are summarized and proposed.

Recent research efforts in bone tissue engineering have been primarily directed towards manufacture-viable synthesis of biomaterials that can significantly enhance the biocompatibilities and osteogenic capabilities on the new biomaterials. This paper presents a straightforward, cost-effective, optimized, and well-controlled hydrothermal synthesis of Nb-doped potassium titanate nanofibers in high-purity. Characterization data revealed that the Nb-doping potassium titanate maintained the crystal structure, showing great promise for applications in bone tissue engineering.

Sharing confidential information is a critical concern in today’s world. Secret sharing schemes facilitate the sharing of secrets in a way that ensures only authorized participants (shareholders) can access the secret using their allocated shares. Hierarchical secret sharing schemes (HSSSs) build upon Shamir’s scheme by organizing participants into different levels based on priority. Within HSSS, participants at each level can reconstruct the secret if a specified number, denoted as the threshold value (t), or more of them are present. Each level has a predetermined threshold value. If the number of participants falls below the threshold at any level, higher-level participants must be involved in reconstructing the secret at lower levels. Our paper proposes schemes that implement hierarchical access structures and enable the sharing of multiple secrets. Additionally, our proposed scheme includes share verification. We have analyzed potential attacks and demonstrated the scheme’s resistance against them. Through security analysis and comparison with existing schemes, we highlight the novelty and superiority of our proposed approach, contributing to advancements in secure information sharing practices.

Acidic ostreolysin A/pleurotolysin B (OlyA/PlyB, formerly known as ostreolysin (Oly), and basic 20 kDa equinatoxins (EqTs) are cytolytic proteins isolated from the edible mushroom Pleurotus ostreatus and the sea anemone Actinia equina, respectively. Both toxins, although from different sources, share many similar biological activities: (i) colloid-osmotic shock by forming pores in cellular and artificial membranes enriched in cholesterol and sphingomyelin; (ii) increased vascular endothelial wall permeability in vivo and perivascular oedema; (iii) dose-dependent contraction of coronary vessels; (iv) haemolysis with pronounced hyperkalaemia in vivo; (v) bradycardia, myocardial ischemia and ventricular extrasystoles accompanied by progressive fall of arterial blood pressure and respiratory arrest in rodents. Both types of toxins are haemolytic within nanomolar range concentrations, and it seems that hyperkalaemia plays an important role in toxin cardiotoxicity. However, it was observed that the haemolytically more active EqT III is less toxic than EqT I, the most toxic and least haemolytic EqT. In mice, EqT II is more than 30 times more toxic than OlyA/PlyB when applied intravenously. These observations imply that haemolysis with hyperkalaemia is not the sole cause of the lethal activity of both toxins. Additional mechanisms responsible for lethal action of the two toxins are direct effects on heart, coronary vasoconstriction and related myocardial hypoxia. In this review, we appraise the pathophysiological mechanisms related to the chemical structure of OlyA/PlyB and EqTs, as well as their toxicity.

The paper discusses the mechanism of montmorillonite structure alteration and bentonites properties modification (on the example of samples from clay deposit Taganka, Kazakhstan) due to the thermochemical treatment (treatment with inorganic acid solutions at different temperatures, concentrations and reaction times). With the use of the suit of methods certain processes were distinguished: transformation of montmorillonite structure, which appears in the leaching of interlayer and octahedral cations, protonation of the interlayer and OH groups at octahedral sheets. Changes in the structure of the 2:1 layer of montmorillonite and its interlayer result in significant changes in the properties – reduction of cation exchange capacity and an increase of specific surface area. The results of the work showed that bentonite clays retain a significant portion of its adsorption properties even after the long term and intense thermochemical treatment (6M HNO3, 60°C, 108 hours)

Bio-inspired gyroid triply periodic minimum surface (TPMS) lattice structures have been the focus of research in automotive engineering because they can absorb a lot of energy and have wider plateau ranges. The main challenge is determining the optimal energy absorption capacity and accurately capturing plastic plateau areas using finite element analysis (FEA). Using nTop's Boolean subtraction method, this study combined walled TPMS gyroid structures with normal TPMS gyroid lattice. This made a composite TPMS-gyroid lattice with relative densities ranging from 14% to 54%. Using the ideaMaker software and the fused deposition modeling (FDM) Raise3D Pro 2 3D printer to print polylactic acid (PLA) bioplastics in 1.75 mm filament made it possible to slice computer aided design (CAD) models and fabricate 36 lattices samples precisely layer by layer technique. Shimadzu 100kN testing equipment was utilized for the mechanical compression experiments. And the validation using finite element analysis (FEA). Further, CTG was examined using a field emission scanning electron microscope (FE-SEM) before and after compression testing. The composite TPMS gyroid lattice showed potential as shock absorbers for vehicles with relative densities of 33%, 38%, and 54%. The Gibson-Ashby model showed that the composite TPMS gyroid lattice deformed mainly by bending, and the size effect was seen when the relative densities were less than 15%. The lattice's relative density had a significant impact on its ability to absorb energy. The research also explored the use of these innovative foam-like composite TPMS-gyroid lattices in high-speed crash box scenarios, potentially enhancing vehicle safety and performance.

This paper investigates the impact of debt financing on dividend payments when they face the agency costs of free cash flow. Focusing on a sample of 120 firms listed on the Saudi Stock Exchange during the period 2011-2021. The study found a negative association between agency cost of free cash flow and dividend payment. More importantly, our research highlights the significant role of long-term debt in making more prudent use of free cash flow. The obligation to meet interest and principal payments acts as an incentive for them to steer clear of unprofitable expenses and risky investments. Concurrently, long-term debt imposes restrictive clauses in debt contracts, such as minimum dividend distribution requirements, which further encourage higher dividend payments. Since interest and debt repayments are fixed obligations, using free cash flow for dividend disbursement is considered a more profitable and beneficial approach for shareholders in the context of Saudi Arabia.

This study aimed to evaluate the impact of Candida albicans on subgingival biofilm formation on dental implant surfaces. Scanning electron microscopy (SEM) and confocal laser scanning microscopy (CLSM) were used to compare biofilm structure and microbial biomass in the presence and absence of the fungus after periods of 24, 48, and 72 h. Quantitative polymerase chain reaction (qPCR) was used to quantify the number of viable and total micro-organisms for each of the biofilm-forming strains. A general linear model was applied to compare CLSM and qPCR results between control and test conditions. The biofilm developed with C. albicans at 72 h had a higher bacterial biomass, with a significantly higher cell viability (p &lt; 0.05). After both 48 and 72 h of incubation, in the presence of C. albicans, there was a significant increase in counts of Fusobacterium nucleatum and Porphyromonas gingivalis and in the cell viability of Streptococcus oralis, Aggregatibacter actinomycetemcomitans, F. nucleatum, and P. gingivalis. Using a dynamic in vitro multispecies biofilm model, C. albicans exacerbated the development of the biofilm grown on dental implant surfaces, significantly increasing the number and cell viability of periodontal bacteria.

Depressions containing partially molten rocks were investigated in Quaternary pebbly sedi-ments in Alpine foreland in Bavaria, Germany. Ruins of limekilns from 18-19th centuries are abundant around Seeshaupt. They are usually associated with earthworks for fuel feeding and protection from wind. Depressions contain partially molten stones from furnace walls, with lime and burnt loam remnants. On the surface of pebbles (typically gneisses), green glass formed with chemical composition possibly affected by moderately volatile components of wood biomass, mainly K and Cu. Thermoplastic deformation of pebbles is limited and the sur-face melt deformation points to slow flow. At Emmerting, on the other hand, two walled circu-lar depressions which lack additional earthworks have been identified as possible impact cra-ters. Thermally affected pebbles show much more intense deformation. Colorless to greenish glass, also K and Cu enriched, usually forms only thin surface coatings, in places covered by younger melt extruded from pebble interior. Burnt loam is missing. At Grabenstätt-Kaltenbach, a depression of unclear origin was investigated. Morphologically, it matches craters rather than limekilns, but anthropogenic contamination (brick-like material) is probable. The rare molten samples do not display extreme deformation features. The thermally affected stones, mainly those from Emmerting, have elevated magnetic susceptibility.

Micro satellites must survive severe mechanical conditions during their launch phase. Therefore, structural design requirements are imposed on the micro satellites. These requirements are the strength requirement and the stiffness requirement. Usually, the structural design of a micro satellite is performed using the internal stress analysis and the natural frequency analysis, which are based on a Finite Element Method (FEM). The validity of this structural design is evaluated through vibration tests. In an early stage of development, which has a FEM model of a satellite in the process of creation, presumption of the natural frequency of a satellite may be difficult. In this study, a simple method for determining the longitudinal and lateral minimum natural frequencies of the micro satellites during the ascent phase was clarified. The structure of the micro satellites used in this research is made of aluminum alloy, and they have a monocoque structure. The Young's modulus and moment of inertia of area used to calculate the minimum natural frequencies were determined using the area ratio of the monocoque structure to the entire satellite. When this method is used, the estimated minimum natural frequencies of the longitudinal direction and the lateral direction are in agreement with the measured values acquired by the vibration tests. In order to shorten the process of micro satellites development, this paper describes a practical estimation method of the minimum natural frequency for micro satellites.

A novel quasi-twisted miniaturized wideband Branch Line Coupler (BLC) is proposed. The design is based on bisecting the conventional microstrip line BLC transversely and folding bisected sections on double-layered substrates with a common ground plane in between. The pair of quarter wavelength horizontal parallel arms is converted to a Z-shape meandered microstrip line in the designed structure. On the other hand, the pair of quarter wavelength vertical arms are cut by half into two lines and converted to a periodically loaded slow wave structure. The bisected parts of BLC are placed on the opposite side of the doubled-layer substrate and connected through four vias passing through the common ground plane. This technique enabled a compact BLC size of 6.4×18 mm2, which corresponds to a surface area miniaturization by ~50% as compared to the classical BLC size of 10×23 mm2 at 6GHz, Moreover, the attained relative bandwidth is 73.9% (4.6-10 GHz) for S11, and 75.8% (4.5-10 GHz) for S33 as compared to 41% for the ordinary BLC at the same resonant frequency. The circuit is constructed on a double-layered low-cost FR4 substrate with a relative permittivity of 4.3, and a loss tangent of 0.025. An isolation of -13dB was realized in both S13 and S31 demonstrating an excellent performance. The transmission coefficients between input/output ports S21, S41, S23, and S43 are between -3.1dB to -3.5dB at the frequency of 6GHz. Finally, the proposed BLC provides phase differences between output ports of 90.5o and 94.8o at the frequency of 6GHz when the input ports 1 and 3 are excited, respectively. The presented design offers the potential of being utilized as a unit cell for building a Butler-matrix (BM) for sub-6GHz 5G beamforming networks.

Due to its size, wood dust often plays the role of a raw material used as a source of energy. However, it is nevertheless an unavoidable byproduct generated during the milling of wood or wood-based composites. The research presented here is focused on the selected properties of 3-layer plywood, produced with the utilization of dust from the milling of three-layer particleboard as a filler in the bonding mass. Four types of filler were used in the study: commercial rye flour, wood dust naturally occurring in the composition of particles used industrially for particleboard production, wood dust from the first batch of shredded particleboard, and dust from the second round of milled particleboard. In the context of this investigation, the highest modulus of elasticity (MOE) values were observed in reference samples. Conversely, for samples featuring filler material from the initial milling process, there were no substantial differences in filler content. Notably, in samples where the filler was sourced from the secondary milling of particleboard, the modulus of elasticity exhibited an upward trend in conjunction with increasing filler content. A similar trend was observed in samples utilizing the naturally occurring dust. Meanwhile, the modulus of rupture (MOR) decreased with an elevated degree of milling, though it displayed a slight increase as the filler content increased. With regard to shear strength testing, the most favorable outcomes were achieved in samples incorporating filler material from the initial milling of particleboard. The thickness swelling of the plywood reached its peak in variants utilizing filler material from both the initial and secondary milling of particleboards. In contrast, water absorption testing exhibited a more pronounced response in the newly introduced variants, although samples incorporating filler from the initial and secondary milling processes eventually yielded results akin to the reference sample, with the naturally occurring dust displaying higher water absorption values. In terms of density profiles, the highest density values were observed in samples utilizing rye flour as the filler material. A similar density profile was observed in samples with 5 parts of wood flour as filler, although the density of the adhesive was slightly lower in these cases. An increase in the quantity of wooden filler material resulted in a commensurate increase in plywood thickness. The research confirms the possibility of using the aforementioned dust as an alternative to conventional fillers in plywood technology. It also raises the question of how to effectively remove glue residues from wood-based composite dust, which would enhance their absorption properties.

The resonance spectrum of surface resistance derivative in quasi-two dimensional layered organic conductors has been calculated numerically for the out-of-plane and in-plane magnetic field. Not all but some of the resonances in a given series of transitions are present in the spectra. They are observed at the positions corresponding to the maxima in the surface resistance derivative curve and are in a good agreement with previously calculated magnetic field resonance positions. For tilted magnetic fields, there are more resonances present in the spectrum than in the case of a non-tilted field. Apart from the resonances corresponding to the transitions between the adjacent surface states there also appear resonances involving the transitions between the more distant surface states. This is correlated with the specific topology of Fermi surface of the organic conductors. The presented calculations will allow correct interpretation of the experimental curves for the resonance spectrum, and also to obtain information on the surface properties of these materials for their possible implementation in fabrication of devices based on organic molecular conductors.

In this study, Li-Al-OH layered double hydroxide (LDH), which was prepared by solvent-free one-step mechanochemical reaction of LiOH and Al(OH)₃, was applied to remove boron from aqueous solution. Dry-grinding for 3 h at a rotational speed of 500 rpm, Li/Al molar 1/2 was the optimum condition to prepare highly crystalline of Li-Al LDH phase with no evident impure phases. Two milling products with Li/Al molar ratio at 1/2 and 2/2 were evaluated for boron adsorption. The results confirmed that Li/Al molar ratio 2/2 sample showed high boron adsorption capacity due to the physical adsorption of Li-Al-OH LDH and chemical synergism of phase gel Al(OH)₃. The adsorption isotherms, described by the Langmuir model, indicated maximum monolayer boron uptake capacity 45.45 mg/g, implying competitive adsorption capacity of the material in our experiment.

Timely and accurate acquisition of information on distribution of the crop planting structure in Loess Plateau of eastern Gansu Province, one of the most important agricultural areas in western China, is crucial for promoting fine management of agriculture and ensuring food security. In this study, the Object-Based Image Classification (OBIC), the Random Forest (RF) and Convolutional Neural Network (CNN) models were employed to classify the crop planting structure of four representative test areas in Qingyang City in a precise manner. Firstly, different optimal segmentation scales for various crops were selected using the Estimation of Scale Parameter 2 (ESP2) tool and the Ratio of Mean Difference to Neighbors(ABS) to Standard Deviation (RMAS)model. The images were then segmented through multiresolution segmentation combined with the Canny Edge Detection algorithm. Secondly, the L1 regularized logistic regression model was utilized to select and optimize 39 spatial feature factors including spectral, textural, geometric, and index features, in conjunction with phenological factors. Lastly, under the multi-level classification framework, the Random Forest (RF) classifier and Convolutional Neural Network (CNN) model, combined with object-based multiresolution segmentation, was used to classify the crop planting structure. The findings show that: Thanks to the Canny Edge Detection algorithm, we can obtain a more complete boundary of the segmented objects and improve the separability. The optimal segmentation scales for corn, vegetables, and buckwheat were found to be 55, 70, and 35, respectively, while wheat and apple had optimal segmentation scales of 65. In addition to phenological characteristics, the number of selected spatial features for corn, vegetables, buckwheat, wheat, and apple were 9, 7, 16, 12, and 10, respectively. The CNN model demonstrated high consistency with the RF model in the classification results, but the accuracy of RF model is higher than that of CNN model on the whole. The overall accuracy of classification using RF model in four test areas registered 91.93%, 94.92%, 89.37% and 90.68%, respectively. This paper introduced crop phenological factors, effectively improving the extraction precision of shattered agricultural planting structure in the Loess Plateau of eastern Gansu Province. Its findings have important application value in crop monitoring, management, food security and other related fields.

Genetic variability in rice breeding program plays the very crucial role. It provides outstanding pool of superior alleles governing better agronomic and quality characters through association mapping. For the understanding of population structure and genetic relationship among the different rice lines is indispensable prior to setting of correlation among dynamic alleles and traits. In the present investigation, genetic diversity and population structure of 116 rice accessions by using 64 polymorphic SSR markers was targeted for the evaluation of the genetic relatedness and diversity. Genotyping assessment based on SSR markers revealed a total of 225 alleles, with an average PIC value of 0.755. The germplasm lines were classified into three distinct subgroups through population structure analysis, utilizing both model and distance-based approaches. AMOVA analysis showed that 11% of the total variation could be attributed to differences between groups, while the remaining 89% of the variation was likely due to differences within groups. The study suggests that the population structure and genetic relatedness should be considered when working with the core collection of 116 rice germplasm lines for association mapping, aiming to establish marker-trait associations.

Most IoT systems meant for implementing mission-critical systems are multi-layered based. The majority of the computing is done in the services and gateway layer. The Gateway layer connects the Internal section of the IoT to the cloud through the Internet. The failure of any node between the services servers and the gateways will isolate the entire network leading to zero tolerance. A networking topology is required to connect the service servers to the gateways, yielding 100% fault tolerance. Empirical formulation of the model chosen to connect the service’s servers to gateways through routers is required to compute the fault tolerance of the network. Rectangular and Interstitial Mesh have been proposed in this paper to connect the service servers to the gateways through the servers that yield 0.999 fault tolerance of the IoT network. An empirical formulation is also presented using which the Fault tolerance of the IoT network can be computed. An enhancement of 11% in the fault tolerance capability of an IoT network has been achieved by implementing Rectangular and Interstitial Mesh in the gateway layer of the network.

The surface thermodynamic properties of polymers and copolymers modified by supramolecular structures are very used in several industrial processes, such as selective adsorption, paints, coatings, colloids, and adhesion applications. Background: Inverse gas chromatography at infinite dilution was proved to be the best technique to determine the surface properties of solid surfaces by studying the adsorption of some model polar and non-polar organic molecules adsorbed on solid surfaces by varying the temperature. Methods: The retention volume of adsorbed solvents is a precious parameter to obtain the London dispersive and polar free energies and the London dispersive surface energy of styrene–divinylbenzene copolymer modified by supramolecular structure of melamine using the Hamieh thermal model and our new methodology consisting in the separation of the two polar and dispersive free energy of interaction. This led to the determination of the polar acid and base surface energy, and the Lewis’s acid-base constants of the various solid materials. Results: all surface energetic properties of styrene–divinylbenzene copolymer modified by melamine at different percentages were determined as a function of temperature, following our new methodology. Conclusions: It was observed that the styrene–divinylbenzene copolymer exhibited the highest London dispersive surface energy which decreased when the melamine percentage increased. All materials presented higher Lewis’s basicity and this Lewis’s basicity increased with the percentage of melamine.

The role played by non extensive thermodynamics in physical systems has been under intense debate for the last decades. With many applications in several areas, the Tsallis statistics has been discussed in details in many works and triggered an interesting discussion on the most deep meaning of entropy and its role in complex systems. Some possible mechanisms that could give rise to non extensive statistics have been formulated along the last several years, in particular a fractal structure in thermodynamics functions was recently proposed as a possible origin for non extensive statistics in physical systems. In the present work we investigate the properties of such fractal thermodynamical system and propose a diagrammatic method for calculations of relevant quantities related to such system. It is shown that a system with the fractal structure described here presents temperature fluctuation following an Euler Gamma Function, in accordance with previous works that evidenced the connections between those fluctuations and Tsallis statistics. Finally, the fractal scale invariance is discussed in terms of the Callan-Symanzik Equation.

The present article describes the synthesis of an isonicotinate-derived meso-arylporphyrin, that has been fully characterized by spectroscopic methods (including fluorescence spectroscopy), as well as by elemental analysis and by HR-MS. The structure of a n-hexane monosolvate has been determined by single crystal X-ray diffraction analysis. The radical scavenging activity of this new porphyrin against the 2,2-diphenyl-1-picrylhydrazyl (DDPH) radical has been measured. Its antifungal activity against three yeast strains (C. albicans ATCC 90028, C. glabrata ATCC 64677 and C. tropicalis ATCC 64677) has been tested, using the disk diffusion and the microdilution methods. Whereas the measured antioxidant activity was low, the porphyrin showed moderate but encouraging antifungal activity. Finally, a study of its effect on the germination of lentil seeds revealed interesting allelopathic properties.