We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

Motivated by the PEACOC project on metal recovery from solid wastes, an innovative magnetic density separation (MDS) process has been developed for granular material sorting. It has intrinsic advantages over the existing industrialized MDS by eliminating fluid turbulence and particle jamming problems. The new MDS applies an inclined planar magnet and a horizontal basin containing a static magnetic fluid as the separation medium. A particle sliding phenomenon is identified as a feature of the process which could help the separation. The MDS successfully sorted shredded PCBAs to concentrate valuable metals and sorted shredded wires to reduce metallic contaminants in the plastic fractions. A pilot scale facility is introduced to show the design to achieve continuous production and to reduce the consumption of ferrofluid.

In the drive towards environmental restoration and sustainable energy solutions, effective utilization and management of agricultural crop residues are vital to mitigate greenhouse gas (GHG) emissions and waste accumulation. Converting biogenic wastes into biofuels and bioproducts has the potential to tackle the energy crisis and contribute to environmental remediation. In this investigation, teff husk, primarily generated in Ethiopia during teff production within the agro-industrial sector, is used as the feedstock for the slow pyrolysis process. In Ethiopia, it is estimated that over 1.75 million tons of teff husk are generated annually, with a significant portion being incinerated in the fields, resulting in substantial environmental pollution. This study focuses on assessing teff husk as a potential material for slow pyrolysis, a crucial stage in biochar production, to tap into its biochar-producing potential. To determine the composition of the biomass, the teff-husk was initially analyzed by thermogravimetry. The significant presence of fixed carbon indicates that teff husk is a viable candidate for pyrolytic conversion into biochar particles. The process of slow pyrolysis took place at three varied temperatures—specifically, at 400, 450, and 500 °C. Process parameters of slow pyrolysis such as reaction time, temperature, and heating rate were enhanced to obtain maximum biochar yields. The highest biochar yield of 43.4 wt% was recorded at optimized reaction time, temperature, and heating rate of 120 min, 400 °C, and 4.2 °C/min, respectively. Furthermore, biochar's physicochemical, SEM-EDX, FTIR, and TGA characterization were performed. The thermal stability and carbon content of biochar were found to rise at higher temperatures. Unlike fuel recovery, the results suggest that teff-husk can be used as a feedstock for biochar production.

DIEP-based breast reconstruction necessitates wide undermining at the abdominal donor-site, creating large wound areas. Flap harvesting is usually conducted using electrosurgical dissection devices. This study sought to compare the clinical outcomes in patients after using the PEAK PlasmaBlade (PPB) versus monopolar electrocautery (MPE). This retrospective cohort study included 128 patients with DIEP-based breast reconstruction. Patient characteristics as well as information on the postoperative course were collected and a comparative evaluation was conducted. The MPE group exhibited significantly (p* = 0.0324) higher abdominal drainage volume (351.11 ± 185.96 ml) compared to the PPB group (279.38 ± 183.38 ml). Subgroup analysis demonstrated that PPB significantly reduced postoperative wound fluid in patients with BMI > 30 kg/m² (p* = 0.0284), without prior neoadjuvant chemotherapy (p** = 0.0041), and among non-smokers (p = 0.0046). Furthermore, postoperative pain was significantly (p**** < 0.0001) lower in the PPB cohort. This study confirms the non-inferiority of the PEAK PlasmaBlade to conventional electrocautery for abdominal flap harvesting. The PPB demonstrated advantages, notably reduced drainage volume and lower postoperative pain levels. Recognizing patient subsets that benefit more from the PPB highlights the importance of personalized device selection based on patient characteristics.

Background. Cervical esophageal reconstruction is vital for improving the quality of life in cancer surgery patients. Microsurgery is crucial, providing vascularized tissue for defect repair, particularly in secondary cases with a higher risk of failure due to larger defects and damage from previous surgery and radiotherapy. The purpose of this study was to describe the clinical characteristics of a series of patients who underwent secondary repair of esophageal defects and provide practical information for the management and treatment of such cases based on the authors' experience and the literature review. Methods. We retrospectively reviewed the electronic medical records of the Plastic Surgery Clinic at the University of Trieste to identify cases of patients who underwent secondary esophageal microsurgical reconstructions following oncological surgery. Patient demographics, etiology of esophageal defects, previous surgical history, and preoperative assessments were collected from medical records. Surgical techniques employed for reconstruction, such as pedicled flaps or free tissue transfers, were documented along with intraoperative details. Postoperative outcomes, including complications, graft viability, and functional outcomes, were evaluated during follow-up. Results. We treated 13 cases of secondary esophageal reconstructions from 2011 to 2022. Most commonly, Antero-Lateral Thigh (ALT) flaps were used in 10 cases, while 2 cases employed Radial Forearm Flap (RFF), and 1 a chimeric parascapular flap. No flap failures occurred during a median 50-month follow-up. One ALT flap patient experienced post-op stricture but maintained swallowing ability. A single tracheoesophageal fistula occurred in a RFF patient with a history of radiotherapy and completion lymph node dissection. Conclusions. Cervical esophageal reconstruction significantly impacts patients' quality of life by restoring oral feeding and phonation. When local flaps fall short, microsurgical reconstruction with intestinal flaps is valuable, but burdened by limitations. For challenging secondary cases, ALT or RFF flaps emerge as safer options due to their robust pedicles, yielding low complication rates and positive functional outcomes.

Seedling emergence is crucial for the establishment and growth of crops and is influenced by topsoil temperature and moisture. Mulching has been widely used to promote seedling emergence in areas with a cold spring. This study was conducted to determine and simulate the effects of transparent plastic film mulch on surface soil moisture, temperature, and seedling emergence of spring maize in Northwest China. Four treatments were used: no mulching (CK), full plastic film mulch (PMF), and partial plastic film mulch, 60 cm in width (PM60, 40 cm uncovered between rows of mulch) or 30 cm in width (PM30, 20 cm uncovered between rows of mulch). The effects of soil water conservation and temperature enhancement gradually decreased as the plastic film width decreased, but there was little difference between PMF and PM60 treatments. Soil-water-modified growing degree days (WGDD) described the beneficial effects of soil moisture and temperature with respect to seedling emergence under mulching conditions. Plastic film mulching markedly accelerated seedling emergence and increased final seedling emergence rate because mulching can shorten the autotrophy duration and maintain surface soil moisture, which leads to increased germination. The effects of seedling emergence improvement decreased as the plastic film width decreased. The relationship between WGDD and cumulative relative seedling emergence (CRE) was adequately described by a Gompertz function.

Evans' Syndrome (ES) is a rare autoimmune disorder characterized by the simultaneous occurrence of immune thrombocytopenia (ITP) and autoimmune hemolytic anemia (AIHA). Thrombotic complications in ES patients are uncommon, particularly involving Buerger's Disease (BD). We report a case of a 49-year-old male with ES and a history of diabetes and heavy smoking, presenting with a necrotic wound on his right great toe. Diagnostic evaluations revealed severe stenosis and thrombosis in the lower limb arteries, diagnosed as BD. The patient underwent successful popliteal-tibioperoneal artery bypass surgery and subsequent disarticulation and revision of the distal phalanx, followed by the application of an acellular dermal matrix (ADM) to promote healing. Post-surgery, the patient showed significant improvement in blood flow and complete epithelialization without complications. This case highlights the importance of a multidisciplinary approach in managing complex wounds in ES patients, suggesting potential treatment pathways for future cases involving BD

Calcium sulphate (CS) is currently used as a bioabsorbable, completely synthetic and sterile material in the management of infected tissues and dead spaces (DS) mainly resulting from surgical procedures. Residual DS in the postoperative, may create an environment where hematomas fill up and bacteria can proliferate, leading to a high incidence of postoperative infections. Considering the available reviews in the literature, CS has been mainly studied in orthopedic surgery mostly giving brilliant results and low complication rates. Nowadays, orthopedists avail it in the form of pearls both as a bone void filler and as an “off-label” delivery agent for antibiotics in arthroplasty, chronic osteomyelitis and open fractures, paving the way of its application in many other contexts given its natural dis-position to biodegradation. In the last years, CS beads have been gaining ground in the general, vascular and endocrinological surgical specialties. Despite its clear potential and the increasing number of scientific evidences on the safety and effectiveness of CS application in the prophylaxis and treatment of infections, there are not many studies reporting on its application in fields other than orthopedics, with a substantial paucity in plastic and reconstructive surgery literature. This is some-how surprising, since reconstructive surgery often deals with complex wounds secondary to bone and soft tissue exposure, suture dehiscence, trauma, and surgical site infections. As far as we know this is the first updated systematic review assessing the state of the art, indications and new perspectives on the application of CS beads in plastic and reconstructive surgery.

Flap surgery is a common method used to cover defects following tumor ablation, trauma, or infection. However, insufficient vascularity in the transferred flap can lead to flap necrosis and failure. Proper postoperative monitoring is essential to prevent these complications. Recently, research has explored the use of infrared thermal imaging in plastic surgery, leading to its clinical application. This study investigates the use of a forward-looking infrared (FLIR) camera to monitor blood flow in flaps. In the study, 28 rats underwent reverse McFarlane flap surgery, and their flaps were analyzed using a FLIR thermal imaging camera seven days post-surgery. Additionally, thermal images of flaps were taken on postoperative days 0, 1, 2, 3, and 7 in 22 patients. The study focused on temperature differences between normal skin and the perforator compared to the average flap temperature. Results showed that the temperature difference was higher in the necrosis group and increased over time in cases of total necrosis. A lower perforator temperature compared to the flap's average indicated vascular compromise, potentially leading to flap failure. The FLIR camera, being contact-free and convenient, shows promise for understanding and inferring the clinical progression of flaps in postoperative monitoring.

The high prevalence of human papillomavirus (HPV) infection in oropharyngeal squamous cell carcinoma (OPSCC) is well-established, with p16 expression being a strong predictor. HPV-related tumors exhibit unique mechanisms targeting p16 and p53 proteins. However, re-search on HPV prevalence and the combined predictive value of p16 and p53 expression in head and neck cutaneous squamous cell carcinomas (HNCSCC), especially in Asian populations, is limited. This retrospective study surveyed 62 HNCSCC patients (2011–2020), excluding those with facial warts or other skin cancers. All patients underwent wide excision and biopsy. Immuno-histochemical staining for HPV, p16, and p53 yielded both positive and negative results. The relevance of each marker was investigated by categorizing the tumor locations into high-risk (Area H) and mid-risk (Area M) zones based on recurrence frequency. Of the 62 patients, 20 (32.26%) were male, with an average age of 82.27 years (26–103). Area H included 19 cases (30.65%), with the eyelid and lip being the most common sites (five cases, 8.06%). Area M in-cluded 43 cases (69.35%), with the cheek being the most common site (29 cases, 46.77%). p16 ex-pression was positive in 24 patients (38.71%), p53 expression in 42 patients (72.58%), and HPV in five patients (8.06%). No significant association was found between p16 expression and HPV presence (p > 0.99), with a positive predictive value of 8.33%. This indicates that p16, a surrogate marker of HPV in OPSCC, is not a reliable marker for HPV in HNCSCC. This study enhances our understanding of the relationship between HPV, p53, and p16 in HNCSCC in Asian populations and offers valuable insights for further research.

Background: This study aimed to investigate the impact of the COVID-19 pandemic on breast reconstruction trends in the United States, focusing on implant-based and autologous techniques, as well as the timing of reconstruction (immediate vs. delayed). Methods: A retrospective analysis of data from the American Society of Plastic Surgeons' National Plastic Surgery Statistics from 2015 to 2022 was conducted. Annual trends in breast reconstruction procedures were analyzed, comparing the pre-pandemic (2015-2019) and pandemic (2020-2022) periods. Results: The total number of breast reconstructions increased from 106,338 in 2015 to 151,641 in 2022. The proportion of implant-based reconstructions decreased from 81.41% pre-pandemic to 76.51% during the pandemic (p < 0.001), with a notable rise in direct-to-implant procedures from 10.37% to 19.12% (p < 0.001). Autologous reconstructions increased from 18.59% to 23.49% (p < 0.001). Among autologous techniques, DIEP flaps remained the most popular. Immediate reconstruction rates increased from 72.61% pre-pandemic to 75.57% during the pandemic, while delayed recon-struction rates decreased from 27.39% to 24.43% (p < 0.001). Conclusions: The COVID-19 pandemic has significantly influenced breast reconstruction trends in the United States, with a shift towards autologous techniques, particularly DIEP flaps, and an in-crease in immediate reconstructions. These changes may reflect adaptations in surgical practice and decision-making processes in response to the unique challenges posed by the pandemic. Further research is needed to assess the long-term outcomes and patient satisfaction associated with these trends.

The practice of collecting, treating and management of solid waste prior to disposal has become a necessity in developing and modern societies. Over the years, it is known that most wastes that are disposed have a second hand value. However, the construction cost for conventional Material Recovery Facility(s) (MRFs) has been a major barrier for implementation. These technologies require considerable technical expertise, which is often not available in developing nations to successfully operate the MRFs. Covenant University; a private mission institution through her waste to wealth scheme is focused on managing and processing used materials to reusable products. These include Pet bottles, Paper wastes, Food wastes from cafeteria, plastic food packs, nylon, tin cans and others. Specific areas chosen for the Survey include the residential areas for staff and students and the two cafeterias. The waste generated was characterized based on the waste stream so as to quantify the amount of recyclable waste generated and most occurring. The survey involved the use of structured questionnaires, on-site observations and measurements. The study reveals an average amount of recyclable waste generated per day in the institution as 13.46% pet bottles, 4.03% paper, 55.56% food waste, 12.64% plastic, 9.63% nylon and 4.68% tin cans. The study established that adequate waste characterization is a requirement for effective integrated solid waste management which would boost resource recovery, reuse and recycling.

Cutaneous squamous cell carcinoma is a prevalent malignancy with a rising incidence and notably high mutational load. Exploring the genetic nuances of cSCC and investigating molecular approaches stands as a potential avenue for improving outcome in high-risk patients. This retrospective case-control study involved two cohorts of 14 patients (“discovery cohort”) and 12 patients (“validation cohort”) with cSCC located in head-neck anatomical district and diagnosed at pT2 stage. Overall, cases developed early local relapse of the disease whereas controls never re-lapsed during the entire follow-up period. Next generation sequencing (NGS) approach conducted on histological samples revealed that TP53 and CDKN2A were the most frequently mutated genes in our series. No specific mutation was identified as potential prognostic or therapeutic targets. Controls exhibited a tendency toward a higher mutational rate compared to cases. It is possible that an increased number of mutations could prompt the cSCC to expose more antigens, becoming more immunogenic and facilitating the recognition by the immune system. This could enhance and sustain immunological response, potentially preventing future recurrences.

Neurofibromas, rare benign tumors of the peripheral nerve sheath, present diagnostic challenges, particularly in diabetic patients with toe ulcers. This case involves a 55-year-old female with type 2 diabetes mellitus who developed an enlarging ulcer on her right second toe. The initial evaluation suggested a diabetic ulcer; however, advanced imaging revealed a mass-like lesion. Partial excision and biopsy confirmed a neurofibroma with spindle cells within the myxoid stroma and S100 protein expression. One month later, total excision and Z-plasty reconstruction were performed under general anesthesia. The patient’s postoperative recovery was uneventful, and the patient was discharged without complications. Follow-up revealed successful healing with no recurrence or functional issues. This case highlights the importance of considering neurofibromas in the differential diagnosis of diabetic toe ulcers to avoid misdiagnosis and ensure appropriate management.

This paper presents the results of investigations into the pyrolysis of waste polypropylene in a laboratory fixed-bed batch reactor. The experiments were designed and verified in such a way as to allow the application of the Response Surface Methodology (RSM) in the development of an empirical mathematical model that quantifies the impacts mentioned above. The influence of the mass of the raw material (50, 100 and 150 g), together with the reactor temperature (450, 475 and 500 °C) and the reaction time (45, 50 and 75 min) was examined. It has been shown that the mass of the raw material, i.e. the filling volume of the reactor, has a significant influence on the pyrolysis oil yield. This influence exceeds the influence of reactor temperature and reaction time. This was explained by observing the temperature change inside the reactor at three different spots at the bottom, middle and top of the reactor. Recorded temperature diagrams show that with greater masses of feedstock, local overheating occurs in the middle part of the reactor, which leads to overcracking of vapor products, and from there to an increased formation of non-condensable gases, i.e. reduced yield of pyrolytic oil.

Thin people who undergo implant insertion into the chest wall face a high risk of implant exposure to the external environment. Five months after an 8-year-old boy underwent implantable cardioverter-defibrillator (ICD) implantation in a subcutaneous pocket in the left anterolateral chest wall to manage long QT syndrome, ICD replacement became necessary owing to exposure risk from distal and lateral thinning of the ICD pocket. Pocket rupture and exposure would increase the risk of infection; therefore, we performed ICD removal and primary pocket closure. Two weeks later, a new suprafascial pocket was created, acellular dermal matrix (ADM) was attached to the inner wall to prevent ICD protrusion, and a new ICD was inserted. One year postoperatively, the ADM was engrafted, and no complications were observed. A thin subcutaneous layer increases the risk of ICD implantation complications. Inner wall strengthening with ADM can help prevent pocket rupture.

Households and businesses are generating unprecedented levels of electrical and electronic wastes (e-waste), fueled by modernisation and rapid obsolescence. While the challenges imposed by e-waste are similar everywhere in the world, disparities in progress to deal with it exists; with developing nations such as South Africa lagging. The increase in e-waste generation increases the need to formulate strategies to manage it. This paper presents an overview of e-waste management on a global and South African scenarios with a specific case for Cathode Ray Tube (CRT) waste management practices in South Africa. CRTs present the biggest problem for recyclers and policy makers because they contain hazardous elements such as lead and antimony. Common disposal practices have been either landfilling or incineration. The research into the South African practices with regards to CRT waste management showed that there is still more to be done to effectively manage this waste stream. This is despite clear waste regulatory frameworks in the country. However, recent developments have placed e-waste as a priority waste stream, which should lead to intensified efforts in dealing with it. Overall, these efforts should aim to maximise diversion from landfilling and to create value-addition opportunities, leading to social and environmental benefits.

Recycling information can be complex and often confusing which may subsequently reduce the participations in any waste recycling schemes. As a result, this research explored the roles as well as the importance of a holistic approach in designing recycling information using 15 expert-based in-depth interviews. The rationale was to offer a better understanding of what constitutes waste, recycling, and how recycling information should be designed and presented to make recycling more attractive/convenient. Based on the research participants’ perceptions with supports from the existing studies, this research sub-categorised recycling information into three different themes, termed the “WWW” of recycling information components. As a result, these components (or attributes) were extensively described (using findings of semi-structured interviews) to elicit pragmatic guidance for practitioners, policy-makers, and other stakeholders in designing structured communication or information strategies that may simplify and subsequently increase waste-recycling practices. The policy implications of holistic information in enhancing recycling are further discussed.

The characteristics of gap plasmon formed by nanoparticle-on-mirror (NPOM) structure composed of metal nanoparticles (MNP) and metal thin films have aroused the interest of various optoelectronic devices. The resonant spectrum obtained by the internal coupling effect of gap can be flexibly controlled by the polarization of incident light and the thickness of the dielectric layer between MNP and metal thin films. We have theoretically studied the resonance spectra of polarization-dependent gold ellipsoidal nanoparticles (GENP) and gold thin films in the gap region of NPOM structures. GENP and gold thin films are separated by a dielectric layer with a refractive index of 1.36. We observe that the intensity of the local electric field resonance peak in the gap region is inversely proportional to the polarization angle. Similarly, the intensity of the local electric field resonance peak in the gap region is inversely proportional to the thickness of the dielectric layer. We have obtained more than 2200 V/m local electric field intensity (dielectric layer thickness 0.3nm). Finally, the resonant peak wavelength of the electric field in the gap region of the NPOM structure is also controlled by the polarization angle of the incident light and the thickness of the dielectric layer.

Solid-state batteries (SSBs) have emerged as a promising alternative to conventional lithium-ion batteries, with notable advantages in safety, energy density, and longevity, yet the environmental implications of their lifecycle, from manufacturing to disposal, remain a critical concern. This review paper examines the environmental impacts associated with the production, use, and end-of-life management of SSBs, starting with the extraction and processing of raw materials which highlights significant natural resource consumption, energy use, and emissions. A comparative analysis with traditional battery manufacturing underscores the environmental hazards of novel materials specific to SSBs. The review also assesses the operational environmental impact of SSBs by evaluating their energy efficiency and carbon footprint in comparison to conventional batteries, followed by an exploration of end-of-life challenges including disposal risks, regulatory frameworks, and the shortcomings of existing waste management practices. A significant focus is placed on recycling and reuse strategies, reviewing current methodologies like mechanical, pyrometallurgical, and hydrometallurgical processes, along with emerging technologies that aim to overcome recycling barriers, while also analyzing the economic and technological challenges of these processes. Additionally, real-world case studies are presented, serving as benchmarks for best practices and highlighting lessons learned in the field. In conclusion, the paper identifies research gaps and future directions for reducing the environmental footprint of SSBs, underscoring the need for interdisciplinary collaboration to advance sustainable SSB technologies and contribute to balancing technological advancements with environmental stewardship, thereby supporting the transition to a more sustainable energy future.

Plastics, once regarded as a revolutionary material shaping modern society, now poses an unprecedented threat to our environment. Household solid waste sorting stations produce several fractions, one of which contains a high concentration of Low-Density Polyethylene (LDPE) film waste (packaging, sunscreen film, etc.). This fraction is difficult to recycle because it contains quite a lot of impurities. Usually, it is sent to the cement factories that burn it together with other fuels. However, with some processing techniques such catalytic pyrolysis this fraction could be valorized. In this paper the experiments which were carried out at a laboratory scale installation, in batches with a processing capacity of 1-3 kg of waste. The pyrolysis reactor is connected to a distillation column giving the possibility to separate the fractions. The gaseous and liquid fractions were characterized by GC-FID-TCD (gases) and GC-MS (liquids) analysis. Natural catalysts such as bentonite or clinoptilolite were studied and used in the melting of plastic mass to simplify the process as much as possible. To test the activity of the catalysts, the pyrolysis of LDPE granules was initially studied. It was found that natural zeolites are much more active than bentonite and that a minimum concentration of 5-10% is needed to have a positive effect on the composition of the fractions (increasing the weight of the light fractions C1-C6, C6-C10 and C11-C13) in relation to the heavy fractions C13-C20 and C20+. Catalytic pyrolysis gives a completely different distribution of light hydrocarbons. The best catalyst selected from LDPE lab experiments, was then tested upon the pyrolysis of plastic film waste obtained by a waste treatment plant. The research objective reported in this paper was to obtain a fraction of combustible gases in the largest possible proportion, which can be much easier exploited by burning in an engine that drives an electric generator.

Adipose tissue-derived stem cells (ADSCs) represent a subset of mesenchymal stem cells in every adipose compartment throughout the body. ADSCs can differentiate into various cell types, including chondrocytes, osteocytes, myocytes, and adipocytes. Moreover, they exhibit a notable potential to differentiate in vitro into cells from other germinal lineages, including endothelial cells and neurons. ADSCs have a wide range of clinical applications, from breast surgery to chronic wounds. Furthermore, they are a promising cell population for future tissue-engineering uses. Accumulating evidence indicates decreased proliferation and differentiation potential of ADSCs with increasing age, body mass index, diabetes mellitus, metabolic syndrome, or exposure to radiotherapy. Therefore, recent literature thoroughly investigates this cell population's senescence mechanisms and how they can hinder their possible therapeutic applications. This review will discuss the biological mechanisms and the physio-pathological causes behind ADSC senescence and how they can impact cellular functionality. Moreover, we will examine the possible strategies to invert these processes, re-establishing the full regenerative potential of this progenitor population.

Mining is an important industry, accounting for 6.9% of global GDP. However, global development promotes accelerated demand, resulting in the accumulation of hazardous waste in land, sea, and air environments. It reached 7 billion tonnes of mine tailings generated yearly worldwide, and 19 billion solid tailings will be accumulated by 2025. Adding to this, the legacy of environmental damage from abandoned mines is worrying; in Canada there are around 10,000 abandoned mines, 50,000 in Australia, 6,000 in South Africa, and 9,500 coal mines in China, reaching 15,000 by 2050. In this scenario, restoration techniques from mining tailing have become increasingly discussed among scholars due to their potential to offer benefits towards reducing tailings levels, thereby reducing environmental pressure for the correct management and adding value to previously discarded waste. This review paper explores available literature on the main techniques of mining tailing recycling and reuse and discusses leading technologies, including the benefits and limitations, as well as emerging prospects. The findings of this review serve as a supporting reference for decision-makers concerning the related sustainability issues associated with mining, mineral processing, and solid waste management.

This paper focuses on the highly radioactive, long-lasting nuclear waste produced by the currently operating fission reactors and on the way to deal with the sensitive issue of spent fuel reprocessing. The review includes a short description of the fission process and a detailed analysis of the more hazardous radioisotopes produced either by secondary reactions occurring in the nuclear installations or by decay of the fission fragments. Also outlined are the strategies presently adopted to minimize the harmfulness of the nuclear waste to be disposed and discussed advanced options and possible solutions proposed for the recycling of the used fuel and for the reusing of some technologicaly relevant radioisotopes.

Treatment techniques for facial paralysis have evolved significantly over the past few decades, offering a variety of options to improve facial symmetry and muscle function. The purpose of this paper is to introduce a novel static treatment technique for the surface of the nasolabial fold (NLF) in patients with chronic facial nerve paralysis, aged between 40 and 80 years, who are not candidates for dynamic rehabilitation and present with NLF erasure. The surgical marking process was initiated by determining the projection of the nasolabial fold on the paralyzed side, through measurement of the NLF on the non-paralyzed side. Subsequently, a line was drawn around the nasal ala, and a second line was demarcated in the medial region of the sulcus. In the region close to the nasal ala, along this second line, a notch was planned. The procedure was conducted under local anesthesia. In this study, four procedures were performed without any complications. Comparatively, the outcomes demonstrated an improvement in facial symmetry, the creation of a new NLF, elevation of the ipsilateral lip commissure, and correction of nasal deviation. The proposed technique is straightforward, reproducible, and can be performed in an outpatient setting.

Plastic contamination of small dimensions (

This study investigates the effects of Zinc (4wt.%) and severe plastic deformation on the mechanical properties of AZ61 magnesium alloy through the stir-casting process. The severe plastic deformation (equal channel angular pressing (ECAP)) has been done followed by T4 heat treatment. The microstructural examinations revealed that the addition of 4wt.%Zn enhances the uniform distribution of β-phase, contributing to a more uniformly corroded surface in corrosive environments. Additionally, dynamic recrystallization (DRX) significantly reduces the grain size of as-cast alloys after undergoing ECAP. The attained mechanical properties demonstrate that after a single ECAP pass, AZ61 + 4wt.%Zn alloy exhibits optimal yield strength (YS), ultimate compression strength (UCS), and hardness. This research highlights the promising potential of AZ61 + 4wt.%Zn alloy for enhanced mechanical and corrosion-resistant properties, offering valuable insights for applications in diverse engineering fields.

Objectives: Describe the epidemiology of burns in the pediatric population. Analyze and compare the results obtained from the treatment of burn wounds by using the bio-preserved human epidermis allograft (BHEA) and other types of dressings and determine the need for further need of a skin graft. Methods: A retrospective cross-sectional study of pediatric population with burn injuries was conducted, grouped into categories based on their age group, and the mechanisms of injury into 6 categories: scald, flame, contact, electrical, chemical and friction. Describing the extension and depth of the burn injury. The results of treatment of two groups; the patients who used (BHEA) and the group with “other dressings” were analyzed by inferential statistics to establish the relationship between the use of BHEA and the need for skin grafts compared to the other group. Results: A total of 65 patients were obtained. The average age was 4.5 years (±3.8). Preschoolers (1-5 years old) were the most frequent age group 64% (n=42). Male patients represented 61% (n=40) of cases. Scald was the most reported mechanism 64% (n=42). The average total body surface area burned (TBSAB) was 10.8% (± 9.2). Mixed partial thickness burn (superficial and deep) was the most common with a 55%. The head was the most affected anatomical site; 30%. The face was the most reported “special anatomical site” with a 40% (n=30). 32.2 % of the population (n=21) was treated with BHEA. The average time of epithelialization of the BHEA group was 8 days (±7.2), and their average hospital stay time was 7 days (±5.7). In the “other dressing” group, the average epithelialization time was 18 days (±13.6), and the average hospital stay time was 11 days (±12.6). Fifty percent (n=22) of the “other dressing” group required skin grafts. In the BHEA group only 19% (n=4) required skin grafts. An OR of 0.23 and CI of 95% (0.06 – 0.81) with a p value of (0.017) for the need of skin grafts after de use of BHEA was obtained. Conclusion: The epidemiological results reported are similar to those described in the literature. The use of (BHEA) proved to be a good option for the management of partial thickness burns and burns in transition, promoting timely epithelilization and avoiding deepening of the burns while reducing morbidity, hospital stay and care costs.

In the era of mounting water scarcity, particularly in arid regions, the agricultural sector is striving to optimize the water resource management practices. Treated wastewater (TWW) has emerged as a viable alternative to freshwater for irrigation, offering a sustainable solution to water conservation. However, ensuring the safety and quality of TWW is paramount to safeguard for both crop health and environmental integrity. Electrical conductivity (EC), a critical factor in assessing TWW suitability for irrigation, can significantly impact crop yields and soil health since it is directly linked to the concentration of dissolved salts and ions. Therefore, this study delves into the development of advanced predictive models for EC assessment by employing supervised machine learning (ML) techniques like the Support Vector Regression (SVR), Adaptive Network-based Fuzzy Inference System (ANFIS), and Multiple Linear Regression (MLR). The TWW samples collected from Al-Qatif area, Saudi Arabia were assessed in the lab through a sensor-based real-time monitoring system integrated with Internet of Things (IoT) network and a multiprobe device. The key water quality parameters assessed involved, temperature (T), pH, Oxidation Reduction Potential (ORP), Resistivity (RES), Total Dissolved Solids (TDS), Salinity and Turbidity which served as the foundation for these models, given their profound influence on and their anticipated impact on EC levels. Following feature selection, two distinct model combinations were identified for the SVR, ANFIS and MLR models. Furthermore, to evaluate prediction performance, four statistical criteria, including coefficient of determination (R²), correlation coefficient (R), mean square error (MSE), and root mean square error (RMSE), were employed. Overall, the comparative performance results proved that ANFIS-M2 indicated the strongest predictive capability with the R² value of 0.99572 and 0.75145 and the RMSE values of 0.00965 and 0.01134, respectively in both calibration and verification stages.

In this study a material based on Polyethylene (PE) and Microcrystalline Cellulose (MC) was developed as a breathable packaging film. Surface functionalization of MC with 3 aminopropyltriethoxysilane (APTES) shows to be an efficient alternative to tailor their properties and increase opportunities for the application of MC on the reinforcement of polymers such polyethylene (PE). Functionalization of MC with mentioned silane derivative was achieved using a green method and later used on the development of composites with PE in three percentages (1, 3 and 5%). All the materials were prepared by melt blending and characterized, in terms of structural properties (ATR-FTIR and FTIR in transmittance, EDX, SEM), thermal properties (DSC and TGA), thermomechanical properties (DMA), contact angle measurements and permeability to oxygen and water vapor. The materials demonstrated to have potential to be used as breathable film packaging of fresh products.

The new unique technology for granulation of metals and nonmetallic melts is presented in the paper. It was created on the newly developed controlled film flow disintegration with rapid cooling of the droplets and solidified granules in amorphous state. Three new phenomena discovered by us created the base for 3 different methods for granulation of metals and nonmetallic melts in a wide range of granules’ sizes. Electromagnetic resonance method allows producing granules of metals in the range of 1 mm and over. The soliton-like vibrational regime is available for production of any granulation material in the range 0.1-1 mm. Moreover, the shockwave regime is applicable for producing particles from 10 micrometers by size. All methods produce particles of the stated size with a narrow distribution by size: deviation from the average size no more than 50%. The other known methods do not produce granules with such high cooling rate, which can realize the amorphous state and cannot regulate size of particles in such bright but narrow range from 10 micrometers to 1-2 mm.

This paper investigates an innovative photovoltaic cell configuration, denoted as “Au/CuSCN/RbGeI3/CdTe/ZnO/TiO2/FTO", using SCAPS-1D simulation. The research focuses on optimizing device performance by analyzing key components, including ZnO as the electron transport layer (ETL), RbGeI3 as the perovskite absorber layer, CuSCN as the hole transport layer (HTL), and CdTe as the active buffer layer. A comparison is made with the standard “Au/CuSCN/CH3NH3SnI3/CdTe/ZnO/TiO2/FTO" configuration under dark and illuminated conditions. Through an in-depth investigation involving temperature effects, generation rate analysis, RbGeI3 absorber layer thickness, Nd level, and interface defect levels, an optimized design for a unit area is achieved. The proposed solar cell demonstrates outstanding performance metrics, including an open circuit voltage (Voc) of 0.94V, a short circuit current density (Jsc) of 34.52mA/cm2, a fill factor (FF) of 77.77%, and an energy conversion efficiency (η) of 25.40%. These values significantly outperform the reference models with energy conversion efficiencies of 10.11% and 21.09%. Real-world applicability is validated by implementing these optimized characteristics in a photovoltaic system for Pakistan’s geographical location using PVSyst software. The suggested solar cell achieves a remarkable performance ratio (PR) of 85.6%, surpassing the PR of the reference basic solar cell model at 83%. The findings of this research offer a promising and superior solar cell design, incorporating innovative materials and optimization techniques to achieve exceptional energy conversion efficiency and overall performance. This study’s outcomes have the potential to advance photovoltaic technology and contribute to sustainable energy solutions worldwide.

Solid waste management is a global issue that affects every individual living in the world directly or indirectly. Failing to manage the waste properly will cause harm on public health, our natural environment, and even our happiness and prosperity. When asked about the reason behind the failure of third time plastic ban in Bhutan, one of the Bhutanese said it’s because of the lack of cooperation from public to support the move of government. Clean Bhutan, a non-governmental organization (NGO) that aims Zero Waste Bhutan by 2030, has collected around 5,900 metric tons of waste from December 2014 to February 2018. This project will create some awareness regarding the management of waste at individual level when people come in contact with the family of the researcher. It also talks abot how waste management and biodiversity conservation can go side by side.

Background: Extracellular Vesicles are pivotal mediators in intercellular communication, facilitating the exchange of biological information among healthy, pathological and tumor cells. Between the diverse subtypes of extracellular vesicles, exosomes have unique properties, clinical and therapeutical applications, even towards cancer. Breast cancer ranks as one of the most prevalent malignancies across the globe. Both the tumor core and its surrounding microenvironment engage in a complex, orchestrated interaction that facilitates the cancer’s growth and spread. Methods: The most valuable and significant PubMed Literature about extracellular vesicles and adipose–derived stem cells exosomes was selected and analyzed in order to report their biological properties and potential applications, in particular on the Triple–Negative Breast Cancer. Results: Adipose–derived stem cells exosomes represent a potential tool to target the tumor core of the Triple–Negative Breast Cancer, its microenvironment and surrounding tissues including metastasis. The authors are developing a supportive Triple–Adipose–derived stem cells Exosomes [T.A.E.] Technology against breast cancer in order to perform a selective preconditioning of the cancer before or while the traditional oncological treatments are running. Conclusion: The possibility to exploit the impact of Adipose–derived stem cells exosomes within the T.A.E. Technology against the Triple–Negative breast cancer is real, highlighting a new era for supportive measures against breast cancer.Keywords: Extracellular vesicles; Exosomes; Adipose–derived stem cells, Tumor microenvironment, Triple–Negative Breast Cancer, T.A.E. Technology.

It is of great academic significance to understand how the atomic structure of interfaces and boundaries in materials impacts the magnetic coupling nature across the boundaries and encourage development of state-of-the-art magnetic devices. Here, we carry out a systematic investigation of the atomic and electronic structures of twin boundaries (TBs) in LiFe5O8 thin films and determine their concurrent magnetic couplings using atomic-resolution transmission electron microscopy and atomistic first-principles calculations. The results show ferromagnetic or antiferromagnetic coupling can exist across the different TBs in LiFe5O8 (LFO) thin films and electrical structures within a few atomic layers directly rely on the TB atomic core structures. Uncovering one-to-one relationship between the magnetic properties of individual TB and the local atomic structures will clarify a thorough comprehension of numerous fascinating magnetic properties of commonly utilized magnetic materials, which will undoubtedly encourage the progress of sophisticated magnetic materials and devices.

Technological advancements in the Internet of Things (IoT), unmanned aerial vehicles (UAVs), and novel technological tools have transformed disaster management practices from localized approaches to a global framework. These innovations necessitate a unified understanding and application of diverse methodologies at an international level, ensuring they are accessible and operational across different sectors. This integration is crucial not only for technical personnel but also for medical teams, who play a pivotal role in disaster response and management. By fostering a comprehensive grasp of these methods, we can enhance coordination, efficiency, and effectiveness in addressing disasters on a global scale. The authors aimed to provide a comprehensive overview of emerging techniques that are driving shifts in strategic approaches and treatment technologies. Recognized as a domain of continuous research and development, this overview, by necessity, remains an incomplete snapshot of an evolving field. It highlights the dynamic nature of technological and strategic advancements, underscoring the importance of ongoing investigation and innovation to stay abreast of current trends and future directions. The article also highlights the importance of international collaboration beyond societal and national boundaries A single paragraph of about 200 words maximum. For research articles, abstracts should give a pertinent overview of the work. We strongly encourage authors to use the following style of structured abstracts, but without headings: (1) Background: Place the question addressed in a broad context and highlight the purpose of the study; (2) Methods: briefly describe the main methods or treatments applied; (3) Results: summarize the article’s main findings; (4) Conclusions: indicate the main conclusions or interpretations. The abstract should be an objective representation of the article and it must not contain results that are not presented and substantiated in the main text and should not exaggerate the main conclusions.

Astola Island is the first marine protected area of Pakistan acknowledged 2017, June 15. It is a rich biodiversity hotspot, Ramsar site inhabiting endangered species like Green turtle, Hawksbill turtle, and Arabian Humpback whale. A saw-scaled Russell’s viper is endemic to Island. Marine ecology of Astola Island is affected by plastic pollution resulting in coral destruction, ocean acidification, global warming, fishing nets blockage, water pollution, and coastal erosion. Zeolite catalyst synthesized from environmentally friendly way by coal fly ash to degrade collected plastic waste from Island into useful products in pyrolysis reactor. The synthesized catalyst functionalized further with three type of organosilane(1) Octyltriethoxysilane(OS),(2)Phenyltriethoxysilane(PS)(3)Vinyltriethoxysilane(VS).Zeolite functionalize with octyltriethoxy silane (ZO) shows the highest performance in plastic pyrolysis, resulting in lower degradation temperature, low residue and more product formation may be due to having long chain hydrocarbon and acidic sites. Plastic recycling is the promising solution to tackle plastic blooming issue. Which is negatively impacting all the compartments of ecosystem especially marine environment.

During the MoDeCo2000 scientific and research project on mortars used in the territory of the Roman Danube Limes in Serbia, the biggest challenge was the quest for the provenance of used raw materials. The area where the largest city in the province of Moesia Superior developed, with millennial continuity of land use and settlement, was selected as a case study for deeper research. The material and immaterial values of Roman Viminacium have survived in the later life of the landscape, through the preserved building remains and artifacts, secondary use of building materials, but also toponyms, customs, and stories. Recycling of materials is commonly recognised in the modern age as the industrial processing of existing products in order to obtain raw materials and later prepare new products, representing one of the basic elements of sustainability. However, people throughout history have always used what they had at hand and the building remains were reused, but also recycled for new constructions. In this study we follow the presence of the specific material we call natural brick in the historical Viminacium landscape, focusing on Roman construction and specifically its potential use in lime mortars, connecting humanistic and natural sciences.

Sustainable manufacturing practices are becoming increasingly necessary due to the growing concerns regarding climate change and resource scarcity. Consequently, material recycling technologies have gradually become preferred over conventional processes. This study aimed to recycle waste polylactic acid (PLA) from household-disposed cups and lids to create 3D-printed parts and promote sustainable manufacturing practices. To achieve this, the current study utilised virgin and post-consumer PLA (sourced from household waste) blends. The PC-PLA wastes were shredded and sorted by size with the aid of a washing step, resulting in a filament with a 1.70 ± 0.5 mm diameter without fragmentation or dissolution. A 50:50 wt.% blend of virgin PLA (vPLA) and PC-PLA was selected as the standard recycling percentage based on previous research and resource conservation goals. The study investigated the impact of three 3D printing parameters (layer height (LH), infill density (I), and nozzle temperature (NT))on the quality of 3D-printed parts using a three-level L9 Taguchi orthogonal array. The findings revealed that blending PC-PLA with vPLA led to significant improvements in the tensile, flexural, and impact strengths by 18.40%, 8%, and 9.15%, respectively, compared to those of recycled PLA. This conclusion was supported by the investigation of the fracture surface area, which revealed fractographic features associated with printing parameters, such as plastic deformation and interfilament debonding. An ANOVA analysis revealed a positive influence of larger layer height and high nozzle temperature on the mechanical properties. Subsequently, the optimal printing parameters (LH: 0.3 mm, I: 100%, and NT: 215 °C) were determined using the S/N ratio, and a confirmation test using the optimum printing parameters exhibited a strong correlation with statistically predicted outcomes. Finally, the study used optimum printing parameters to fabricate 100% post-consumer recycled PLA 3D printed parts, demonstrating their potential for low-strength applications. Based on these findings, it can be concluded that virgin and post-consumer recycled PLA blended filament for fabricating 3D printed components is an effective way to support plastic recycling in the context of a circular economy.

Organic soil amendments, such as composts, mitigate the environmental burdens associated with wasting organic resources. Although compost application to soil enhances an agroecosystem's capacity to store carbon and produce food, studies investigating the agronomical efficacy and their ability to ameliorate drought stress when used as a soil amendment are minimal. In this study, we produced and used a nutrient rich co-compost through the composting of sludge, a nitrogen-rich organic material with carbon rich municipal solid wastes (MSW) to evaluate the agronomic efficacy of the MSW derived co-compost and their ability to ameliorate drought stress. Application of co-compost significantly enhanced growth and yield of lettuce and maize, by a magnitude comparable to chemical fertilizers. Furthermore, under drought stress, lettuce plants grown under co-compost soil amendment grew much better with less wilting, more biomass and yield, and improved root growth. Also, co-compost application enhanced relative root mass ratio (RRMR) under drought stress, indicative that co-compost amendment increased the allocation of biomass to the roots, which is an important morphological attribute for drought adaptability. K content in both leaves and roots of plants amended with co-compost was also higher under drought stress, which may have played a role in osmotic adjustment, consequently, the plants exhibited higher leaf relative water content (RWC). Other nutrient elements that were significantly enhanced by co-compost application included Mg, Ca, Fe and Cu. These results provide evidence that MSW co-composting could optimize organic resource recycling for climate change mitigation and agricultural productivity while minimizing nutrient losses from agroecosystems.

In an attempt to reuse fibrous textile waste and, at the same time, to address dye pollution in textile wastewater, waste cotton-based yarn was utilized as both a cheap and sustainable adsorbent and a precursor for carbon adsorbent production. Cotton and cotton/polyester yarn samples underwent thermal modification through carbonization followed by chemical activation with KOH. Various techniques including nitrogen adsorption-desorption isotherms, scanning electron microscopy, Fourier transform infrared spectroscopy, and surface charge determination were employed to analyze the morphological and surface properties of the cotton-based adsorbents. Adsorption properties were evaluated by testing the removal of selected cationic and anionic dyes from water. The impact of temperature, contact time, initial concentration, and pH of the adsorbate solution on adsorption was investigated, with experimental data analyzed using theoretical models. While carbonization alone did not significantly enhance adsorption properties, activated samples exhibited high efficacy in removing both cationic and anionic dyes from water. Despite the negative influence of the polyester component in the carbon precursor on the efficiency of activated samples in removing methyl orange, results indicated that activated cotton and cotton/polyester yarn could be used to prepare highly efficient adsorbents for the rapid removal of methylene blue from real wastewater samples.

As the additive manufacturing industry grows, it is compounding the global plastic waste problem. Distributed recycling and additive manufacturing (DRAM) offers an economic solution to this challenge, but it has been relegated to either small-volume 3D printers (limiting waste recycling throughput) or expensive industrial machines (limiting accessibility and lateral scaling). To overcome these challenges, this paper provides proof-of-concept for a novel open-source hybrid 3D printer that combines a low-cost hanging printer design with a compression screw-based end-effector that allows direct extrusion of recycled plastic waste in large expandable printing volumes. Mechanical testing of the resultant prints from 100% waste plastic, however, showed that combining challenges of non-uniform feedstocks and a heavy printhead for a hangprinter reduced the strength of the parts compared to fused filament fabrication. The preliminary results are technologically promising, however, and provide opportunities to improve on the open source design to help process the volumes of waste plastic needed for DRAM to address the negative environmental impacts of global plastic use.

Abstract: In order to accelerate deployment of distributed recycling by providing low-cost feed stocks of granulated post-consumer waste plastic, this study analyzes an open source waste plastic granulator system. It is designed, built and tested for its ability to convert post-consumer waste, 3-D printed products and waste into polymer feedstock for recyclebots of fused particle/granule printers. The technical specifications of the device are quantified in terms of power consumption (380 to 404W for PET and PLA, respectively) and particle size distribution. The open source device can be fabricated for less than USD$2000 in materials. The experimentally-measured power use is only a minor contribution to the overall embodied energy of distributed recycling of waste plastic. The resultant plastic particle size distributions were found to be appropriate for use in both recyclebots and direct material extrusion 3-D printers. Simple retrofits are shown to reduce sound levels during operation by 4dB-5dB for the vacuum. These results indicate that the open source waste plastic granulator is an appropriate technology for community, library, makespace, fab lab or small business-based distributed recycling.

Graphene was synthesized through a two-step pyrolysis method using waste candlenut (Aleurites moluccanus) shells as the precursor. Cerium (Ce)/graphene composites were prepared via an impregnation technique. The resulting graphene and Ce/graphene were characterized using various analytical methods, including Scanning Electron Microscopy with Energy-Dispersive Spectroscopy (SEM-EDS), X-ray Diffraction (XRD), X-ray Photoelectron Spectroscopy (XPS), Transmission Electron Microscopy (TEM), Thermo Gravimetric Analysis (TGA), Fourier Transform Infrared (FTIR) spectroscopy, Cyclic Voltammetry (CV), and Linear Sweep Voltammetry (LSV). The bio-carbon produced predominantly exhibited a graphene structure with flat carbon morphology and an interlayer distance of 0.33 nm. This structural information is supported by XRD data, which shows a broad and weak peak at 2θ = 26° corresponding to the C (002) plane, indicative of graphene presence. FTIR, XPS, and Raman spectroscopy further confirmed the presence of graphene through the detection of Csp2 aromatic bonds and the characteristic D, G, and 2D peaks. Notably, the performance of cerium can be enhanced by the incorporation of graphene, attributed to the large surface area and chemical interactions between Ce and graphene. Consequently, candlenut-derived graphene shows potential as a supportive material for modifying the properties of cerium, thereby opening avenues for various advanced applications, such as sustainable and high-performance energy storage systems.

The aim of this study was utilization of ground tea waste (GT) left after brewing the black tea as a biofiller of natural rubber (NR) composites. Ionic liquids (ILs), i.e., 1-ethyl-3-methylimidazolium lactate and 1-benzyl-3-methylimidazolium chloride, often used to extract phytochemicals from tea, were applied to improve the dispersibility of GT particles in elastomeric matrix. The influence of GT loading and ILs on curing characteristics, crosslink density, mechanical properties, thermal stability and resistance of NR composites to thermo-oxidative aging was investigated. The amount of GT did not significantly affect curing characteristics and crosslink density of NR composites, but had serious impact on tensile properties. Applying 10 phr of GT improved the tensile strength by 40% compared to unfilled NR. Further increasing in GT content worsened the tensile strength due to the agglomeration of biofiller in elastomer matrix. ILs significantly improved the dispersion of GT particles in elastomer and increased the crosslink density by 20% compared to the benchmark. Owing to the poor thermal stability of pure GT, it reduced the thermal stability of vulcanizates compared to unfilled NR. Most importantly, GT-filled vulcanizates showed improved resistance to thermo-oxidative aging, since the aging factor increased by 25% compared to the unfilled vulcanizate.

Improper disposal of waste plastic has caused serious ecological and environmental pollution problems. Transforming plastics into high value-added chemicals can not only achieve efficient recycling of waste plastics, but also an effective way to control white pollution. The catalyst selectively breaks the C-C bond of polyolefin plastic under heat treatment and converts it into liquid fuel, thus realizing sustainable recycling of plastics and has a good development prospect. This review provides a detailed overview of the current development of catalytic pyrolysis, catalytic hydrolysis, solvent decomposition and supercritical hydrothermal liquefaction for cracking plastics to make fuel oil. The reaction mechanism, influencing factors and promoting effects of catalysts in various degradation technologies are analyzed and summarized and the latest proposed tandem reaction for degrading plastics is briefly introduced. Finally, some optimization paths of waste plastic pyrolysis to fuel oil technology are proposed: synergies between mixed raw materials, in-depth exploration of catalysts, design and manufacture of reactors that match the pyrolysis technology. All these are important research directions for promoting the industrialization of plastic pyrolysis to fuel oil.

We report the relative humidity (R.H.) sensing response of a resistive sensor, employing sensing layers based on a ternary nanohybrid comprising holey carbon nanohorns (CNHox), potassium chloride (KCl), and polyvinylpyrrolidone (PVP) at mass ratios 7/1/2, 6.5/1.5/2, and 6/2/2 (w/w/w/w). The sensing structure comprises a silicon substrate, a SiO2 layer, and interdigitated transducer (IDT) electrodes. The sensing film is deposited on the sensing structure via the drop-casting method. The sensing layers' morphology and composition are investigated through Scanning Electron Microscopy (S.E.M.) and RAMAN spectroscopy. The ternary hybrid-based thin film resistance increases when the sensors are exposed to R.H., ranging from 0% to 100%. The manufactured devices show a room temperature response comparable to a commercial capacitive R.H. sensor and are characterized by excellent linearity, rapid response time, and good sensitivity. The presented sensors exhibit superior performance in terms of sensitivity compared to other similarly manufactured and tested sensors that employ a CNHox-based sensing layer. We explain the sensing role of each constituent of the ternary hybrid nanocomposites based on their chemical and physical properties, electronic properties, and affinity for water molecules. Different alternative sensing mechanisms are considered and discussed, such as the decreasing number of holes in the holey CNHox at the interaction with water molecules, proton conduction, and PVP swelling.

The carbonyl iron particles were dispersed in a polychloroprene rubber (CR) matrix under an external magnetic field for practical application as microwave absorption composites film. The film prepared under external magnetic field with a thickness of only 0.54 mm showed least reflection loss of -15.98 dB and the reflection loss value less than -10.0 dB over the frequency range of 11.4~14.8 GHz. In comparison with the microwave absorption properties of calculation by transmission line theory based on the tested relative complex permittivity and permeability and film prepared by general route without external magnetic field, the film made with external magnetic field exhibited more excellent microwave absorption properties, strongly depending on the increment of anisotropy and rearrangement of magnetic particles. The results indicated the composite film made under external magnetic field have excellent microwave absorption properties, which suggest that the composites thin film could be used as a thinner and lighter microwave absorber.

Silica fly ash, Certyd aggregate, and an alkaline solution were used to produce lightweight geo-polymer concretes. The compressive strength, water absorption, bulk density and SEM photos showing the structure of the obtained composite were carried out. Tests conducted on the specifi-cation of lightweight geopolymer concretes have revealed significant chemical interactions between the ash aggregate and the geopolymer mortar, particularly when the coarse aggregate surface has been pre-treated with an alkaline solution. Statistical analysis of the experimental data, which in-vestigated the influence of three key variables on compressive strength, water absorption, and bulk density of Lightweight Geopolymer Concrete (LBG), identified the following factors as having the most substantial impact: the quantity of alkali used, the curing temperature, and the concentration of alkali in the mixture. The optimal test series exhibited a commendable compressive strength of 20.14 megapascals (MPa), accompanied by a water absorption rate of 14.72% and a bulk density of 1486.6 kilograms per cubic meter (kg/m³). These findings underscore the importance of alkali con-tent, curing temperature, and alkali concentration in tailoring the properties of lightweight geo-polymer concrete to meet specific performance requirements.

Civil construction is one of the oldest known activities in humanity, reports indicate that builders of the Roman Empire already sought the reuse of materials. Currently, considering the depletion of the supply of natural resources, the recycling of solid waste from construction and demolition (CDW), not only provides new products, but also offers ecological and economic alternative. In this context, this research seeks new variables for the disposal of waste from construction and demolition having in the composition of artificial finishing stones an odd possibility to be analyzed. In this research was developed and analyzed a new composite from the construction and demolition waste using as a binder an orthophthalic polyester resin. The residue was sieved and separated by granulometry by the simplex centroid method, the best compacted mixture was determined statically by ANOVA and the Tukey test. The residue was characterized by X-ray fluorescence and the resin by infrared spectroscopy by Fourier transform. Artificial rock plates were produced with 85% residue and 15% resin, by mass, by vibro system, compression and vacuum, later were cut for mechanical, physical and chemical tests. Analysis was performed by scanning electron microscopy of fractured compositions as well as grain sizes. The artificial stone with the best results presented density of 2,256 g/cm3, water absorption of 0.69%, apparent porosity of 1.55%; bending strength of 34.74 MPa and compression of 111.96 MPa; good results in the alterability and thermal tests. In this satisfactory scenario, the use of this waste in the composition of artificial rocks is promising because it directly meets the concept of sustainable development; replacing the concept of end-of-life of the linear economy, by new circular flows of reuse, restoration and renovation, in an integrated process the circular economy; as well as the quality of the final product with properties similar to the artificial rocks already marketed.

Waste glycerol can be subjected to various processing operations, including purification and re-fining, to obtain glycerol of appropriate purity. In addition, alternative methods of utilising waste glycerol are also being sought, e.g. by converting it into other valuable chemical products or biofuels. Therefore, various technologies are being developed to utilise this type of waste effectively and sustainably. The production of value-added products from waste glycerol is an important issue that determines the improvement of the economic viability of biofuel production and corresponds to the model of a waste-free and emission-free circular economy. This paper characterised the mechanisms and evaluated the efficiency of existing methods of microbiological utilisation of waste glycerol into liquid biofuels, including biodiesel, bioethanol and biobutanol, and identified further directions for the production of value-added products. In addition, a bibliographical analysis of publications re-lated to the production of liquid fuels and economically valuable products from glycerol was carried out, the progress of research and application work was assessed and directions for future research were identified.

Solvent free copolymerization of epoxides derived from fatty acid esters of waste cooking oil with phthalic anhydride using (salen)CrIII Cl as catalyst and n-Bu4NCl/DMAP as co-catalyst was carried out for the first time under microwave irradiation, where reaction time was reduced from number of hours to minutes. The polyesters were obtained with molecular weight (Mw = 3084-6740 g/mol) and dispersity values (D = 1.18-1.92), when (salen)CrIII Cl/n-Bu4NCl was used as catalysts. While in case of DMAP as a co-catalyst, polyesters with improved molecular weight (Mw = 5537-6925 g/mol) and narrow dispersity values (D = 1.07-1.28) were obtained even at reduced concentrations of (salen)CrIII Cl and DMAP. The obtained products were characterized and evaluated by attenuated total reflection-fourier transform infrared spectroscopy (ATR-FTIR), proton nuclear magnetic resonance (1H-NMR) spectroscopy, gel permeation chromatography (GPC) and thermogravimetric analysis (TGA) Techniques.

The recycling of common soda-lime glass (SLG) is far from being complete, since the material may contain small polymeric, metallic and ceramic contaminations. This has a negative impact on the quality of new glass articles prepared via re-melting. Alternatively, the full reuse of contaminated cullets could be achieved by low-temperature consolidation into geopolymer-like materials. SLG powders, used either as received or pre-washed in acid solution, were added to a sodium aluminate solution at the room temperature for 3 h, under low-speed mechanical stirring. Microporous semi-crystalline monoliths were formed by the casting of suspensions in plastic molds and cured at 75°C overnight. The monoliths featured hydrosodalite as the main crystalline phase for as received SLG and LTA zeolite in the case of pre-washed SLG. The mechanical properties compared well with those of cementitious materials. Moreover, by addition of coarse glass particles as fillers, the methodology successfully yielded Venetian terrazzo-like samples, which could lead to significant material and energy savings in their manufacture. The proposed approach could also be extended to other difficult-to-reuse glass formulations and provide attractive and versatile up-cycled materials.

The rapid growth of the global population is causing a significant increase in waste production, leading to serious environmental and public health challenges. To address these issues, waste management systems are incorporating advanced technologies. Machine learning and computer vision are used to predict waste patterns, optimize collection schedules, and improve sorting accuracy. Deep learning automates the sorting process, provides predictive analytics, and enhances recycling rates. Robotics, combined with AI and computer vision, improves sorting efficiency, while the Internet of Things (IoT) monitors waste levels and optimizes collection routes. Despite these benefits, challenges such as data scarcity, high computational demands, and the need for substantial infrastructure investments must be addressed. This research explores the integration of advanced technologies into waste management and evaluates their effectiveness using waste datasets. It highlights the potential to tackle environmental challenges and lay the groundwork for more intelligent waste management solutions.

This article raise a topic of critical examination of polypropylene, a key polymeric material, and its extensive application within the automotive industry, particularly focusing on the manufacturing of brake fluid reservoirs. The study aims to enhance the understanding of polypropylene's behavior under mechanical stresses through a series of laboratory destruction tests and numerical simulations, emphasizing the Finite Element Method (FEM). A novel aspect of this research is the introduction of the PEAK parameter, a groundbreaking approach designed to assess the material's resilience against varying states of strain, known as triaxiality. This parameter facilitates the identification of critical areas prone to crack initiation, thereby enabling the optimization of component design with a minimized safety margin, which is crucial for cost-effective production. The methodology involves conducting burst tests to locate crack initiation sites, followed by FEM simulations to determine the PEAK threshold value for the Sabic 83MF10 polypropylene material. The study successfully validates the predictive capability of the PEAK parameter, demonstrating a high correlation between simulated results and actual laboratory tests. This validation underscores the potential of the PEAK parameter as a predictive tool for enhancing the reliability and safety of polypropylene automotive components. The research presented in this article contributes significantly to the field of material science and engineering by providing a deeper insight into the mechanical behavior of polypropylene and introducing an effective tool for predicting crack initiation in automotive components. The findings hold promise for advancing the design and manufacturing processes in the automotive industry, with potential applications extending to other sectors.

In this work, dry and hydrothermal carbonization (DC and HTC) of RDF pellets were conducted to evaluate the physical, chemical, and fuel properties of the produced chars. In the dry carbonization tests, biomass sawdust was incorporated in different proportions on the samples to minimize agglomeration caused by the melting of the plastic fraction. The experiments were carried out in a temperature of 400°C (DC) and 250-300°C (HTC), in a residence time of 30 minutes. The respective chars and hydrochars were characterized according to their mass yield, apparent density, proximate, elemental, and mineral composition, chlorine content, high heating value, thermogravimetric profile, and surface functional groups. The results showed that dry carbonization of RDF pellets with biomass incorporation, followed by a washing step, resulted in the production of chars with improved properties such as higher fixed carbon and HHV (25-26 MJ/kg) and lower ash and chlorine content. Additionally, the HTC experiments demonstrated that hydrochars showed improved properties without the need for biomass addition and washing, however, with no significant difference in the HHV (20-21 MJ/kg). Therefore, DC of RDF pellets with 10% biomass incorporation seems to be a promising option to overcome the constraints of RDF utilization as an alternative fuel.

Thermal and catalytic pyrolysis of virgin low-density polyethylene (LDPE), high-density polyethylene (HDPE), polypropylene (PP) and mixtures of LDPE/PP were carried out in a 200 ml laboratory scale batch reactor at 460 °C in a nitrogen atmosphere. Thermogravimetric analysis (TGA) was carried out to study the thermal and catalytic degradation of the polymers at a heating rate of 10 °C/min. The amount of PP was varied in the LDPE/PP mixture to explore its effect on the reaction. In thermal degradation (TGA) of LDPE/PP blends, a lower decomposition temperature was observed for LDPE/PP mixtures compared to pure LDPE, indicating interaction between the two polymer types. In the presence of a catalyst (CAT-2), the degradation temperatures for the pure polymers were reduced. The TGA results were validated in a batch reactor using PP and LDPE respectively. Thermal cracking results showed that the oil product contains a significant amount of gasoline (C7 − C12) and diesel (C13 − C20) hydrocarbon fractions. The catalyst enhanced cracking at lower temperatures and narrowed the hydrocarbon distribution in the oil towards the gasoline range fraction (C7 – C12). The result suggests that the oil produced from catalytic pyrolysis of waste plastics has a potential as an alternative fuel.

In the present study, a multilayer high barrier thin blown film based on a polybutylene adipate terephthalate (PBAT) blend with polyhydroxyalkanoate (PHA), and composed of four layers, including a cellulose nanocrystals (CNC) barrier layer and an electrospun poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) hot-tack layer, was characterized in terms of surface roughness, surface tension, migration, mechanical and peel performance, barrier properties and disintegration rate. The results showed a material with a smooth surface. The overall migration test showed that the material was suitable for its use as a food contact layer. The addition of the CNC interlayer had a significant effect on the mechanical properties of the system, drastically reducing the elongation at break and, thus, the flexibility of the material. However, the material retained its elastic modulus and tensile strength. The CNC coating had a negative impact on the peeling strength, weakening the inherently strong interlayer adhesivity of the electrospun PHBV fibers. The multilayer had a good barrier to water vapor, and especially to oxygen, with its permeance reduced by up to a 90 % when the CNC layer was present. Finally, the monolayer blend film disintegrated in a period of less than 55 days in a laboratory-scale composting experiment, while the multilayer system disintegrated in 60 days. Overall, the multilayer system formed a fully compostable structure with great potential for use in food packaging applications.

Global wastes accumulate at an accelerating rate especially food and slaughterhouse waste constituting a major proportion owing to inefficient management. The high protein concentration of fish waste and keratinaceous byproducts is hazardous, harbouring pathogens, and emitting toxins. Transforming proteinaceous waste into amino acids (AAs) reduces waste bulk and offers a smarter nutrient approach for agriculture. However, this resource remains underutilized triggering eco-system pollution, diseases spreading, and climate change. Currently, small quantities of proteinaceous waste are valorized as animal feed, fertilizer, and in medical, and biotechnological sectors, which cannot solve bulk waste accumulation further, natural AA sources in agriculture are less recognized meanwhile researchers focus on synthetic AAs. Introducing various plant-nutrient formulas enriching fish AA with keratinaceous waste hydrolysate has not been broadly discussed. With this novel approach, using proteinaceous waste resources in agriculture would solve environmental pollution while minimizing land degradation by synthetic fertilizer. In this review, we illustrate the potential and benefits of valorizing proteinaceous waste in bulk through bioconversion. More importantly, we spotlight the biocompatibility of natural AAs and propose an enrichment, to use the ultimate product as catalysts for crops. Consequently, this approach reduces hazardous waste while paving a paradigm change in agriculture.

Citrus waste has been used as a source of bioplastic research in different ways. Because the juice industry produces significant amounts of residue each year, it would be advantageous to use the byproducts in the creation of new materials. For many years, researchers have been investigating an environmentally friendly way to take citrus and other organic waste and turn it into polymers that may be used, for instance, to produce bio-based and biodegradable films for food packaging. The goal of this study is to create biofilms from orange (OW) and ginger waste (GW) using an ultrafine grinder and study the films' properties. Since pectin has the ability to gel and because cellulosic fibres are strong, citrus waste has been studied for its potential to produce biofilms. After being washed, dried, and milled, orange and ginger waste were shaped into films using a casting process. Tensile testing was used to determine the mechanical properties of biofilms, while dynamic mechanical thermal analysis (DMTA), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC) were used to determine their thermal properties. As the number of grinding cycles increased, the suspension's viscosity increased from 29 to 57 mPa.s for OW and from 217 to 376 mPa.s for GW while the particle size in the suspension significantly decreased. For OW and GW films, the highest tensile strength was 17 MPa and 15 MPa, respectively. The maximum strain obtained among all films was 4.8%. All the tested films were stable up to 150°C, and maximum degradation occurs after 300°C.

Mechanical recycling of solid plastic wastes on a small-scale level can be accomplished with the correct approaches. Thermoplastics are mostly considered for mechanical recycling because of their physical properties and ease of reprocessing. This paper reviews the mechanical reprocessing techniques of selected thermoplastics (polyethylene terephthalate and polyolefins) since they constitute a significant proportion of plastics used commercially. Furthermore, necessary considerations for effective operation of small-scale plants, including energy requirements of machinery and optimisation in order to improve efficiency and product quality, are discussed. A clearer understanding and addressing of the process-related challenges will lead to successful establishment and management of small-scale mechanical recycling facilities to benefit communities. Efficient small-scale mechanical reprocessing establishments have become essential in reducing the environmental impacts of solid plastic wastes and for energy conservation.

The valorization of the large amount of crude glycerol formed from biodiesel industry, is of primordial necessity. One possible direction with high interest to the biorefiniery sector is the production of fuel additives as solketal, though the acetalization of glycerol with acetone. This is a chemical process that conciliates high sustainability and economic interest, since solketal contributes to the fullfilment of a Circular Economy Model through its use in biodiesel blends. The key to guarantee high efficiency and high sustainability for solketal production is the use of a recovery and recyclable heterogeneous catalyst. Some examples are already reported in the literature (first example in 2012), and this review intends to conciliate the information spreaded in this topic and established the most important reacional parameters and the main catalytic characteristics strategies to achieve high solketal production in short reaction time.

Diabetes mellitus is one of the most common endocrinopathies, estimated to affect about 5.4% of the world's population around 2025. It is thought that nearly a third of diabetic patients have some type of skin condition. Frequently, the cutaneous effects of this heterogeneous syndrome are ac-curately detected late in the progressive form of the disease. The main objective of the present study was to identify the main cellular characteristics of the cutaneous microenvironment in exper- imentally induced diabetes mellitus. Skin fragments were harvested from adult white Wistar rats of both sexes, with the weight of 200 g, 12 weeks after streptozotocin diabetes was induced. In parallel with histopathological diagnosis by using hematoxylin and eosine staining, samples were processed by transmission electron microscopy technique and examined with a Philips CM100 microscope. In the apparently macroscopically unchanged tegument, photon microscopy revealed both progres ive thinning of the epidermis in the early stages of diabetes and a significant process of fibrosis and collagen hyalinization in the dermis. In addition, in the early stages, the electron microscopic study provided ultrastructural details characteristic of a senescent phenotype with reduced cell proliferation. The morphological changes in the skin may be the first signs of disruption of carbohydrate metabolism and in the case of established diabetes may reflect its progression and the efficacy of therapy.

When disposing of waste metal resources in landfills, environmental issues such as soil contamination may arise. Recycling these resources not only recovers valuable metals but also mitigates environmental pollution. Platinum (Pt), a valuable metal used in fuel cells for its high water production activity, will see increased future demand as a fossil fuel alternative. This study analyzes the environmental and resource reduction effects of recycled Pt, considering the growing emphasis on its recycling for stable supply and demand of Pt. The environmental impact and resource consumption of recycled Pt with primary Pt (from natural mines) were compared and analyzed using the Life Cycle Assessment (LCA) technique. Results revealed that resource consumption for primary Pt was 8.25E+01 kg Sb-eq./kg, significantly more than the 5.45E+00 kg Sb-eq./kg for recycled Pt. This represents an environmental reduction effect of approximately 93%. In the case of greenhouse gas emissions, primary Pt emitted 1.35E+04 kg CO2-eq./kg, while recycled Pt emitted 6.94E+02 kg CO2-eq./kg, resulting in an environmental reduction effect of approximately 95%. In conclusion, recycling Pt, compared to primary extraction, offers substantial environmental and resource reduction benefits. This study underscores the significance of recycling and highlights the potential environmental improvements achievable through sustainable practices.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

The article aims to present the results of research on anaerobic digestion (AD) of waste wafers (WF - control) and co-substrate system - waste wafers and cheese (WFC - control), combined with digested sewage sludge. The aim of the study was to evaluate the physicochemical parameters of the chitosan/perlite (Ch/P; 3:1) carrier material and to verify its effect on the directions of change of the bacterial microbiome, removal kinetics of organic matter and AD process efficiency. The experiment was conducted in a laboratory, in a periodical mode of operation of bioreactors, under mesophilic conditions. The results of analyses of morphological-dispersive, spectroscopic, adsorption, thermal and microbiological properties confirmed that the tested carrier material can be an excellent option to implement in biotechnological processes, especially in anaerobic digestion. The microstructural properties of the carrier were influenced by both components: perlite determined the development of the specific surface area, while chitosan shaped the porosity of the system. The thermal properties were determined by the less heat-resistant component, present in a threefold higher weight proportion, i.e. chitosan. The evaluation of quantitative and qualitative changes in the genetic diversity of bacterial communities, carried out using Next Generation Sequencing (NGS), showed that the material has a modifying effect on the bacterial microbiome. Amount of bacteria from phyla Actinobacteria, Bacteroidetes, Campilobacterota, Chloroflexi, Euryarchaeota, Planctomycetes, and Proteobacteria decreased while Firmicutes, Synergistetes, and Thermotogae increased during the course of the experiment. The shapes of the FT-IR spectra indicated a dependence of the degradation rate on both the presence of the carrier and the cosubstrate system. Monitoring of the course of AD was carried out by measuring key parameters for the stability of the process: pH, VFA and VFA/TA ratio (volatile fatty acids/total alkalinity). As a result, an increase in the volume of biogas/methane produced, under the influence of the carrier, was recorded for WF-control by 12.05% and for WFC-control by 19.16%. The volume of methane for the WF-control increased from 351.72 m3 Mg-1 VS to 411.14 m3 Mg-1 VS, while for the cosubstrate sample it increased from 476.84 m3 Mg-1 VS to 518.08 m3 Mg-1 VS, confirming the validity of combining the respective cosubstrate with microbial carrier in anaerobic bioreactor.

Peanut hulls (PH) are an edible food waste that is an underutilized food source for human consumption. While edible and palatable, they are mainly diverted to livestock feed or building materials. Here, we describe existing literature on human food valorization of PHs and propose methods to optimize recapturing nutrients (e.g. protein, fiber, polyphenols) lost by treating PHs as waste. Incorporated into common foods, PHs can be processed into functional ingredients to improve nutrient-density and the corresponding positive health outcomes associated with increases in plant foods. PH valorization can also address additional priorities of the UN Sustainable Development Goals using a Food Systems Approach (FSA) including food waste, increasing economic opportunities for farmers, and increasing the availability of healthy shelf-stable foodstuffs to address food security. Recent advances in sustainable food processing technologies can be utilized to safely incorporate peanut hulls into human food streams. We propose future applications that could make meaningful impacts to food availability and the nutritional composition of common foods. While the limited literature on this topic spans several decades, no global operations exist to incorporate peanut hulls and most publications precede the technological ‘green revolution’. The approaches outlined in this review may help bolster commercialization of this underutilized and nutritious food potentially improving opportunities for multiple global stakeholders.

Solid waste management in Accra is a major challenge to the Metropolitan Authorities and inhabitants. The rapidly increasing population coupled with poor capacity of the municipal and private waste management companies to management waste effectively has created issues of environmental concern. Due to poor waste managements systems, most household dispose waste indiscriminately leading to floods and health issues. The study showed that about 60% of household waste is organic materials which has the potential to be converted to compost for agriculture purpose. Meanwhile plastics and rubbers which litters the environment as well as blocking major storm drains and gutters hence creating huge environmental hazard is made of 11% of the total component of most household waste generated daily. The study also revealed that among the methods of disposing waste, dumping waste in skip containers located at authorized places was the preferred means of disposing waste by household though others also dispose waste by other means such as burying and burning. Inadequate skip containers per population of household in an area coupled with irregularity of tracks picking these containers makes skip containers dumping site ugly scene, hence creating health issues. Among the constraints that impact negatively on sustainable waste management in Accra Metropolis, economic constraints was perceived as the main challenge which affect efficient waste management. Currently the country is going through serious economic challenges so government does not release money timely to fund projects which waste management is key. Most donor partners that use to support the government with funds have either reduced or redrawn their services as they have no confidence in the state of Ghana economy. Aside the constrains, the study also indicated that factors such as poor public attitude towards waste management, poor enforcement of sanitation by-laws, inadequate and untimely release of government funds were also seen as the main factors affecting waste management.

Abstract. Graphene family (GF)-Calcium phosphate (CaP) composites, holds great potential as components of bone regeneration materials. GF nanomaterials can be modified physically as well as chemically, which are to be biomimetic, mechanically to be hard due to their capability to support exceptional mechanical, thermal and electronic properties. These biocompatible GF composites coated on the calcium phosphate can enhance and tolerate stem cell growth and differentiation, proliferation into various lineages or interact with bioorganisms. The development in CF-CaP materials and their physicochemical/biointeractions and strategies towards osteoblasts is a great concern to promote faster healing and reconstructions of large bone imperfections or defects. In this review, we explain the influence of the CF-CaP and summarize recent developments on designing CF-CaP architectures as multifunctional bone regeneration platforms. We have also explored the typical biological applications concerning these CF-CaP based bioactive nanocomposites. Furthermore, the future viewpoints and evolving challenges will also be emphasized. Due to the shortage of full-length reviews in this emerging research field, this review would be caught great attention and encourage various new chances across a wider range of disciplines.

CuO-ZnO-Al2O3 catalysts are designed for the low-temperature shift conversion in the process of hydrogen and ammonia synthesis gas production. The paper presents the results of research on recovery of copper and zinc from spent catalysts using pyrometallurgical and hydrometallurgical methods. Under reducing conditions, at high temperature, having appropriately selected the composition of the slag, more than 66% of copper in metallic form and about 70% of zinc in the form of ZnO can be extracted from this material. Hydrometallurgical processing of the catalysts was carried out using two leaching solutions: alkaline and acidic. Almost 62% of the zinc contained in the catalysts has been leached to the alkaline solution and about 98% of copper has been leached to the acidic solution. After the hydrometallurgical treatment of the catalysts, insoluble residue was also obtained in the form of pure ZnAl2O4. This compound can be reused to produce catalysts, or it can be processed under reducing conditions at high temperature to recover zinc. The recovery of zinc and copper from such a material is consistent with the policy of sustainable development and helps to reduce the environmental load of stored wastes.

There is a need to find methods to intensify the anaerobic digestion process. One possibility is the use of pre-treatment techniques. Many laboratory tests confirm their effectiveness, but in most cases, there is no verification work carried out on industrial plants. The aim of the research carried out under laboratory conditions and on a large scale was to determine the technological and energy efficiency of the use of hydrodynamic cavitation in the pre-treatment of a waste mixture from dairy farms. It has been shown that hydrodynamic cavitation significantly increases the concentration of organic compounds in the dissolved phase. In the most effective variants, the increase in the content of these indicators was over 90% for both COD and TOC. The degree of solubilisation achieved was 49±2.6% for COD and almost 52±4.4% for TOC. Under laboratory conditions, the highest effects of anaerobic digestion were achieved after 10 minutes of pre-treatment. The amount of biogas was on average 367±18 mL/gCOD and the amount of methane 233±13 mL/gCOD. Further large-scale optimisation trials showed that after 8 minutes of hydrodynamic cavitation, the biogas yield was 327±8 L/kgCOD with a CH4 content of 62.9±1.9%. With this variant, the net energy yield was 66.4±2.6 kWh/day, a value that was 13.9% higher than the original variant with 10 minutes of disintegration and 3.1% higher than the variant without pre-treatment.

The accumulation of waste polymer in ecosystems is a problem that affects the environment on a global scale. This paper presents the design of Pwave+, a microwave pyrolysis system that has been optimized to recycle waste polymer into valuable hydrocarbon fuels and chemicals. Heating in a microwave oven is both volumetric and rapid, which improves the effectiveness of pyrolysis and the quality of the product. The production of waste polymer oil and gas products was boosted to its full potential by a continuous microwave vortex reactor. The product gases allowed for complete independence in terms of energy production. Modeling, simulation, and experimentation with advanced technology are used to optimize the pyrolysis parameters and the performance of the reactor. As a result, simulation and programming are solutions to problems. The results of this study demonstrated both the technical viability and the long-term viability of continuous microwave pyrolysis as a method for recycling mixed polymer waste streams. The Pwave+ continuous microwave vortex reactor is described in this study. It is capable of converting various polymer waste streams into hydrocarbon products as well as energy. The use of microwaves to assist in the pyrolysis process has the potential to cut down on plastic pollution and the amount of waste that is dumped in landfills. This could provide valuable insights for the design and commercialization of similar systems.

Natural fibres are the preferred options for garment, technical and medical textiles, nonwovens and composites. Their sustainability is a considerable advantage. Though, the nature of silk production and processing involves a large amount of waste. The present review explores the current issues of recycling silk waste into nonwovens for medical and air filtration purposes. The article proposes to obtain nonwovens from short fibres using electrospinning of fibroin solutions in volatile solvents. Longer fibres are proposed to be processed into needle punched nonwoven materials with a selection of an effective antistatic treatment.

Despite the increase in popularity of Zero Waste (ZW) concept, the successful implementation of this concept in waste management is still facing many challenges. The plastic recycling rate in Australia is currently only about 9.4%, which could leave up to 90.6% of plastic consumption being sent to landfills. The state of Victoria (in Australia) has proposed an ambitious plan to upgrade its waste and recycling system and to divert about 80% of waste from landfills by 2030. The aim of this research is to study Victoria’s current waste management plan and to develop a simulation model to assess the feasibility of it achieving zero plastic waste by 2035. In this direction, a fundamental knowledge of global ZW implementation needs to be acquired in order to understand the challenges, obstacles, and uncertainties in achieving ZW target. A simulation model is established using a method called double baselines. This method was developed as an improvisation to address the limitation of data availability for the model development. The model will run on 4 scenarios including one from Victoria’s current plan. Outcomes from the model are produced in comparative charts covering 6 key considerations including the rates of plastic consumption, waste to landfill, diversion, recycling, relative accumulative cost and effort. The findings of this study pointed out that Victoria’s current plan are feasible for its goal and presented with opportunities for improvement especially towards zero plastic waste. Besides, study results also reveal that the Victoria’s current plan to achieve 80% diversion rate by 2030 is possible but the zero plastic waste target by 2035 is less likely to happen.

In the European Union, the demand for polyurethane is continually growing. In 2017, the estimated production value of polyurethane was 700,400T, of which 27.3% is taken to landfill, which causes an environmental problem. In this paper the behaviour of various polyurethane foams from the waste of different types of industries will be analysed with the aim of assessing their potential use in construction materials. In order to this, the wastes were chemically tested by means of CHNS, TGA, and leaching tests. They were tested microstructurally by means of SEM. The processing parameters of the waste was calculated after finding out its granulometry and its physical properties i.e. density and water absorption capacity. In addition, the possibility of incorporating these wastes in plaster matrices was studied by determining its rendering in an operational context, finding out its mechanical resistance to flexion and compression at 7 days, its reaction to fire as well as its weight per unit of area and its thermal behaviour. The results show that in all cases, the waste is inert and does not undergo leaching. The generation process of the waste determines the foam’s microstructure in addition to its physical-chemical properties that directly affect building materials in which they are included, thus offering different ways in which they can be applied.

Due to growing concerns about environmental pollution from plastic waste, plastic recycling research is gaining momentum. Traditional methods, such as incorporating inorganic particles, increasing cross-linking density with peroxides, and blending with silicone monomers, often improve mechanical properties but reduce flexibility for specific performance requirements. This study focuses on synthesizing silica nanoparticles with vinyl functional groups and evaluating their mechanical performance when used in recycled plastics. Silica precursors, namely sodium silicate, and vinyltrimethoxysilane (VTMS), combined with a surfactant, were employed to create pores, increasing silica's surface area. Early-stage introduction of vinyl functional groups prevented the typical post-synthesis reduction in surface area. Porous silica was produced in varying quantities of VTMS, and the synthesized porous silica nanomaterials were incorporated into recycled Polyethylene to induce cross-linking. Despite a decrease in surface area with increasing VTMS content, a significant surface area of 883 m2/g was achieved. In conclusion, porous silica with the right amount of vinyl content exhibited improved mechanical performance, including increased tensile strength, compared to conventional porous silica. This study shows that synthesized porous silica with integrated vinyl functional groups effectively enhances the performance of recycled plastics.

The global increase in population has placed significant pressure on food security, leading to the emergence of aquaculture as a vital source of aquatic foods. However, rising costs and the limited availability of fishmeal in aquafeeds have spurred the search for alternative protein sources. While plant-based ingredients have been integrated into commercial aquafeeds, they come with challenges, including low protein content, palatability issues, and the presence of antinutritional factors. In this context, fish silage, derived from fish waste and discarded fish, stands out as a promising alternative technology due to its cost-effectiveness and sustainability attributes. The production of fish silage involves the addition of organic/inorganic acids or lactic acid bacteria to homogenized fish waste. This process yields a valuable mixture rich in peptides, free amino acids, and partially hydrolyzed proteins, offering significant nutritional benefits for animal diets. Beyond its nutritional advantages, fish silage contributes to environmental sustainability by reducing the impact of waste disposal and enhancing the value of fish waste. The objective of this review is to promote sustainable practices in the aquaculture industry in response to the increasing demand for high-quality feed nutrients. To achieve this, it includes an analysis of research results related to silage technology, an appraisal of the advantages and disadvantages of using fish silage as a feed additive, and a focus on emerging trends in this field.

A tumbler screen type residual film–impurity mixture wind separator as a key equipment for secondary utilization of farmland residual film. During the working process, the proportion of impurities in the separated waste mulch film intermittently increases, resulting in poor working stability of the device, which may hamper long-term operation. In this study, the material inside the separation unit was continuously monitored, and the main factor affecting separator per-formance was determined to be the challenges in the effective depolymerization of some residual film–impurity mixtures. The principles of agglomeration and depolymerization of the residual film–impurity mixtures were analyzed using computational fluid dynamics (CFD) and discrete element method (DEM) flow-solid coupling simulation methods. The key factor affecting the disaggregation of the mixture was the collision force between the residual film–impurity mixture and the trommel screen. The collision force was maximum when the residual film–impurity mixture first collided with the trommel screen when it was fed into the separation device. As determined by force analyses, the key factors affecting the collision force of the process were the material feeding amount and the structure of the inlet. Furthermore, simulations were carried out for different inlet structure forms; the evaluation index was the maximum collision force of the residual film–impurity mixture agglomerate on the trommel screen. The best disaggregation effect was obtained with a square feed inlet and at a feeding rate of 202 kg/h. A prototype was built using these specifications for verification. The average value of the ratio of impurities in the re-sidual film was 6.966%, the coefficient of variation was 7.38%, and the dispersion of statistical results was small. The ratio of impurities in the residual film was kept constant during the con-tinuous operation of the wind separator. Thus, this study analyzed the agglomerate disaggregation process and provided theoretical insights for deter-mining the optimal structures of the inlets of various cleaning devices and the feeding volumes.

This paper is the second part of a two-part report studying the responses of a typical point-contact elastohydrodynamic lubrication (EHL) problem to multiscale roughness that is mimicked by artificially generated waviness with different amplitudes, frequencies, and directions. The previous Part I paper (doi:10.3390/lubricants10120368) focuses on the full film regime, while the current paper focuses on the partial film regime. The amplitudes and frequencies are related to the feature geometry of smooth EHL problems. Generated waviness is input to a transient thermal EHL model. The simulation is conducted 1,600 times for different waviness parameters, loads, and speeds. Eight performance parameters are extracted: the asperity contact ratio, minimum film thickness, maximum pressure, central point film thickness, central point pressure, mean film thickness, coefficient of friction (COF), and the maximum temperature rise. The ratios of the first seven parameters with and without waviness and the asperity contact ratio values are plotted on the frequency–amplitude coordinate plane as contour maps. The influences of the amplitude, frequency, wave direction, load, and speed on the eight performance parameters are analyzed and summarized. The simulated data and plotted contour maps are provided to the readers in the Supplementary Material.

In order to meet the needs of an increasingly complex research landscape, researchers engage in “collaborative prosumption” through open data sharing and reuse. Although significant gains have been achieved in this regards because of growing requirements from funding agencies, governments and journals, the question of how reuse of openly available data for new research contribute to sustainability is yet to be appropriately addressed in the literature. Therefore, relying on a three stage stratified clustered random sampling of the Journal of Applied Econometrics data archive (JAEDA), the present research provides a case study of the value of research data recycling for sustainable research and economic development. More specifically our analysis show that reformatting from wide to long format, openly shared equity price index data on eleven European countries’ extracted from JAEDA, and augmented with country level geospatial Meta data, provides a new basis for interesting descriptive analytics and spatio-temporal econometric modeling and inference. Given the ever-increasing volume of openly available research data, our study provides a first-hand insight on open data reuse, which should benefit all stakeholders in the research community, as they seek sustainable solutions for scientific productivity and progress.

Introduction: Chronic wounds caused by diabetes or lower-extremity artery disease are intractable because the wound healing mechanism is no longer effective due to the poor environment of the wound bed. Biosheet obtained using in-body tissue architecture (iBTA) is a collagen-based membranous tissue that is created within the body and autologously contains various growth factors and somatic stem cells including pluripotent stem cells. When applied to a wound, granulation formation can be promoted and even epithelialization may be achieved. Hearin, we report our clinical treatment experience with seven cases of intractable diabetic foot ulcers. Cases: From 46- to 93-year-old 7 patients had large foot ulcers including heel area, which was failed to heal with standard wound treatment. Methods: Two or four Biosheet-forming molds were implanted subcutaneously in the chest or abdomen, and after 3 to 6 weeks, the molds were removed. Biosheets that formed inside the mold were obtained and applied directly to the wound surface. Results: In all cases, there were no problems with the mold embedding and removal procedures, and Biosheets were formed without any infection or inflammation during the implantation period. The Biosheets were simply applied to the wounds, and in all cases, they adhered within one week, did not fall of, and became integrated with the wound surface Complete wound closure was achieved within 8 weeks in two cases and within 5 months in two cases. One patient was lost due to infective endocarditis from septic colitis. One case required lower leg amputation due to the wound recurrence, and one case achieved wound reduction and wound healing in approximately 9 months. Conclusion: Biotube obtained via iBTA promoted wound healing and were extremely useful for intractable diabetic foot ulcers involving heel area.

Spent coffee grounds (SCG) have great potential as a useful, value-added biological material. In this context, activated carbon (AC) was prepared from SCG by an activation process using H3PO4 at 600°C in air and used as an adsorbent for the azo dye AO7, a model molecule for dye colorants found in textile industry effluents. X-ray diffraction, SEM and BET revealed that the AC was predominantly amorphous, consisting of a powder of 20-100 µm particles with mesopores averaging 5.5 nm in pore size. Adsorption kinetics followed a pseudo-second-order law, while the Langmuir model best fitted experimental isotherm data (maximum capacity of 119.5 mg AO7 per AC g). Thermodynamic parameters revealed that adsorption was endothermic and spontaneous. All the characterizations indicated that adsorption occurred by physisorption via mainly - interactions. The best experimental removal efficiency optimized by means of a Box-Behnken design and response surface methodology was 98% for an initial AO7 concentration of 20 mg.L-1 at pH 7.5 with a dose of 0.285 g.L-1 of AC and a contact time of 40 min. These results clearly show that activated carbon prepared from SCG can be a useful material for efficiently removing organic matter from aqueous solutions.

The rapid development of the photovoltaic (PV) industry will result in an increase in the amount of electrical and electronic waste from used PV panels. Only in Poland, the total capacity installed in photovoltaic sources in Poland in May 2020 exceeded 1,950 MW, and the installation weight was approximately 120,000. tone. The problem arises in the recycling or management of this waste. This work presents methods used to recycle waste into photovoltaic modules. The authors investigated the possibility of mechanical and chemical processing of crystalline silicon. A method of thermal treatment of the panel was also proposed. As a result of the research, it was found that the stage of separating materials (crystalline cream, EVO foil, aluminum frame) plays an important role in the recycling process, which is not easy. Chemical treatment allows the silicon to become plastic and the temperature melts the back layer of the panel.

Density functional theory (DFT) calculations of hydrogen adsorption on titanium nitride had previously shown that hydrogen may adsorb on both titanium and nitrogen sites with a moderate adsorption energy. Further, the diffusion barrier was also found to be low. These findings may qualify TiN, a versatile multifunctional material with electronic conductivity, as electrode material for the hydrogen evolution reaction (HER). This was the main impetus of this work which aims to experimentally and theoretically investigate the electrocatalytic properties of TiN-layers that were processed on Ti substrate using reactive ion sputtering. The properties are discussed focusing on the role of oxygen defects introduced during the sputtering process on the HER. Based on DFT calculations, it is shown that these oxygen defects alter the electronic environment of the Ti atoms which entails a low hydrogen adsorption energy in the range of -0.1 eV; this leads to HER performances that match those of Pt-NPs in acidic media. When a few nanometr thick layer of Pd-NPs is sputtered on-top of the TiN-layer, the performance is drastically reduced. This is interpreted in terms of oxygen defects being scavenged by the Pd-NPs near the surface which is thought to reduce the hydrogen adsorption sites.

Global use of single-use non-biodegradable plastics, like bottles made of polyethylene tereph-thalate (PET), have contributed to catastrophic levels of plastic pollution. Fortunately, microbi-al communities are adapting to assimilate plastic waste. Previously, our work showed a full consortium of five bacteria capable of synergistically degrading PET. Using omics approaches we identified key genes implicated in PET degradation within the consortium’s pangenome and transcriptome. This analysis led to the discovery of a novel PETase, EstB, discovered to hydrolyze oligomer BHET, and polymer PET. Besides genes implicated in PET degradation, many other biodegradation genes were discovered. Over 200 plastic and plasticizer degrada-tion related genes were discovered through the Plastic Microbial Biodegradation Database (PMBD). Diverse carbon source utilization was observed by a microbial community-based as-say, which paired with an abundant number of plastic and plasticizer degrading enzymes in-dicates a promising possibility for mixed plastic degradation. Using RNAseq differential analysis, several genes were predicted to be involved in PET degradation including aldehyde dehydrogenases and several classes of hydrolases. Active transcription of PET monomer me-tabolism was also observed, including the generation of polyhydroxyalkanoate (PHA) bi-opolymers. These results present an exciting opportunity for the bio-recycling of mixed plastic waste with upcycling potential.

Microbial composition across substrates in mangroves, particularly in the Middle East, remains unclear. This study characterized bacterial communities in sediment, water, Terebralia palustris snail guts, and plastic associated with Avicennia marina mangrove forests in two coastal lagoons in the Sea of Oman using 16S rDNA gene MiSeq sequencing. The genus Vibrio dominated all substrates except water, which featured unique genera Sunxiuqinia and Pseudomonas. There were significant differences in bacterial communities on different substrata, in particular plastic. Snail guts harbored the highest number of unique Operational Taxonomic Units (OTUs) in both lagoons. Plastic in the polluted Sawadi lagoon with low salinity harbored distinct genera like Vibrio, Aestuariibacter, Zunongwangia, and Jeotgalibacillus absent in Qurum lagoon with higher salinity and low pollution. Sawadi lagoon exhibited higher species diversity in sediment and plastic substrates, Qurum lagoon demonstrated lower overall species diversity. The PCA indicates that environmental factors like salinity, pH, and nutrient levels significantly influence bacterial community composition across substrates. Variations in organic matter and potential anthropogenic influences, particularly from plastics, further shape bacterial communities. This study highlights the complex microbial communities in mangrove ecosystems, emphasizing the importance of considering multiple substrates in mangrove microbial ecology studies.

Inadequately managed agricultural waste significantly impacts the environment, health, and economy. This form of pollution arises from the underutilization, poor awareness, and insufficient treatment of agricultural waste. Fruit and vegetable wastes are valuable sources of bioactive compounds. This study aims to revalorize discarded waste from red habanero chili peppers (Capsicum chinense) by extracting bioactive compounds through different extraction processes: maceration (ME), maceration assisted by ultrasound (US), Soxhlet extraction (SE), supercritical fluid extraction (SFE), and supercritical fluid extraction with a co-solvent (SFEC). Extraction processes have significant effects on extraction efficiency and phytochemical profile (capsaicinoids and carotenoids recovery). The results indicate that the highest efficiency process is obtained with SFEC, also a high phytochemicals recovery (14.9 mg of total capsaicinoids and total carotenoids 292.09 µg per gram of sample). Concerning to phytochemical profile in the extract, the maceration process gets the highest concentration of compound followed by US and SFEC. These data reveal that the use of SFE and SFEC extraction is recommended for extraction of phytochemicals with biologically activity from red habanero chili pepper waste for diverse industries application.

Water pollution is the main problem in the current scenario which is being faced by mankind due to the industrial and commercial effects. Industrial effluents contain heavy metals and inorganic ions like nitrates and phosphate ions. These ions are being included in waterways through industrial runoff. When the concentration of these hazardous pollutants increases in aquatic flora and fauna causes severe health problems. So remediation of these toxicants from water reserves is of chief importance. Conventional processes along with modern processes are being used for the treatment of industrial wastes. Photo-degradation is a modern method used for the degradation of inorganic ions due to its environmentally friendly nature and cost-effectiveness. In a recent study Aluminum oxide (Al2O3) nanoparticles were synthesized via a green approach at different pH by using Cymbopogan citratus (lemongrass) plant extract and these nanoparticles were used for the removal of inorganic ions from wastewater. The nanoparticles of different pH showed different % degradation of the inorganic ions in acidic medium removal of inorganic waste was less, in basic media % degradation was more as compared to acidic media but maximum % degradation was observed in neutral media like that average % degradation 91% and 81% was observed for nitrate and phosphate ions. The maximum absorbance occurred at 212nm and Al2O3 nanoparticles showed absorbance from 210nm-217nm. The R2 values of pseudo1st, 2nd, and BMG models were 0.956, 0.837, 0.7007 0.95, 0.896, and 0.756 for the nitrate and phosphate ions. Characterizations of synthesized particles were investigated by using UV-visible spectroscopy and other analytical methods like X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). The statistical analyses were done using Simple Linear regression (SLR).

This study aims to explain individual engagement in sustainable waste management behaviors (SWMBs) based on the application of protection motivation theory (PMT). SWMBs include waste avoidance, green purchasing behavior, reuse and recycle, and waste disposal behaviors. This study applies PMT to explore how individuals’ SWMBs are influenced by their perceived threats caused by environmental contamination from waste disposal and their perceived coping capability. The Bangkok metropolitan area was selected as a case study because it has faced serious waste management problems caused by massively increasing amounts of solid waste during the last ten years. Questionnaire surveys were conducted with 193 public and private officers residing in the city of Bangkok. The one-way analysis of variance (ANOVA) was performed to justify the effect of individual threat appraisal and coping appraisal on the engagement in SWMBs. The results demonstrated that respondents’ self-efficacy highly influenced all types of SWMBs. The perceived probability of being impacted from pollutants influenced all of the SWMBs except green purchasing behaviors. Response efficacy did not influence all SWMBs; however, the perceived severity of adverse consequences caused by pollutants highly influenced reuse and recycle behaviors. It could be suggested that PMT is well suited for investigating low-cost and simple SWMBs. It could also be suggested that different communication campaigns should be established to enhance citizens’ engagement in each type of SWMB.

The escalating global population and subsequent demand for agricultural products have led to a surge in agricultural waste generation, posing significant disposal challenges. Conventional disposal methods such as burning and dumping not only harm the environment but also jeopardize human health and safety. Recognizing the urgent need for sustainable waste management, researchers have increasingly focused on repurposing agricultural plant waste as a valuable resource. This paper presents a comprehensive review of the potential of agricultural plant waste in wealth creation and sustainable development. It highlights the detrimental impacts of current disposal methods and emphasizes the necessity for alternative approaches. By analyzing the physical, mechanical, and chemical properties of plant fibers, particularly cellulose, hemicellulose, and lignin, this review underscores their suitability for diverse applications. Moreover, it explores the emerging trend of utilizing pineapple leaf fiber, a sustainable and lightweight material, in structural applications such as UAV construction. With its exceptional mechanical properties and biodegradability, pineapple leaf fiber holds promise as a viable alternative to traditional materials, contributing to a more sustainable future. In conclusion, this review advocates for a paradigm shift towards embracing agricultural plant waste as a valuable asset for economic prosperity and environmental sustainability. It underscores the importance of continued research and technological advancements to unlock the full potential of agricultural waste in fostering a circular economy and driving sustainable development globally.

Currently, there is a tenacious need to find new ways to purify water by eliminating bacterial biofilms, textile dyes, and toxic water pollutants. These contaminants pose significant risks to both human health and the environment. To address this issue, in this study, we have developed an eco-friendly approach that involves synthesizing Cobalt-doped Cerium Iron Oxide (CCIO) nanocomposite (NC) using an aqueous extract of Gossypium arboreum L. stalks. The resulting nanoparticles can be used to effectively purify water and tackle the challenges associated with these harmful pollutants. Nanoparticles excel in water pollutant removal by providing high surface area for efficient adsorption, versatile design for simultaneous removal of multiple contaminants, catalytic properties for organic pollutant degradation, and magnetic features for easy separation, offering cost-effective and sustainable water treatment solutions. CCIO nanocomposite has been synthesized by green co-precipitation method due to biomolecules and co-enzymes present in the aqueous extract of Gossypium arboreum L. stalk; a single-step procedure completed in 5 h reaction time. Further, the synthesis of nanocomposites was confirmed by various characterization techniques such as Fourier-transform infrared (FT-IR) spectroscopy, X-ray diffraction (XRD), Field emission scanning electron microscopy (FE-SEM), Transmission electron microscopy (TEM), Thermogravimetric analysis (TGA), Dynamic light scattering (DLS), and Energy Dispersive X-Ray (EDX). CCIO NCs were discovered to have a spherical shape and an average size of 40 nm. Based on DLS zeta potential analysis, CCIO NCs were found to be anionic. Also, CCIO NCs showed significant antimicrobial and antioxidant activity. Overall, considering the physical and chemical properties, the application of CCIO NCs in the adsorption of various dyes (~91 %) and water pollutants (chromium = ~ 60 %) has been considered since they exhibit great adsorption capacity owing to their microporous structure which can be a step forward in water purification.

Recycling and waste management have garnered immense popularity in recent years, but few studies have been carried out regarding these systems. Therefore, an in-depth literature review was done in order to highlight the different sectors of the recycling system that need to be reformed. Hence this study examined recycling and waste management systems within three categories–medical, municipal, and plastic–that were carried out pre and post COVID by reviewing previous studies, technical reports, and annual reports. This was done by visiting numerous academic search engines alongside online resources that were utilized to assemble literature related to waste and recycling systems. Continuing a recurring idea was that no matter the type of waste, further research regarding all waste should be carried out. Additionally, since recycling and waste management are a vital part of our society, and seeing how unpredictable events such as the pandemic may be, it is paramount that that research is done not only on how the pandemic has affected systems now, but also how we can learn from current issues to utilize them for future “waste shocks”.

Abstract: Colistin is a last-resort antimicrobial for treating multidrug-resistant Gram-negative bacteria. Phe-notypic colistin resistance is highly associated with plasmid-mediated mobile colistin resistance (mcr) genes. mcr-bearing Enterobacteriaceae have been detected in many countries, with the emergence of colistin-resistant pathogens a global concern. This study assessed the distribution of mcr-1, mcr-2, mcr-3, mcr-4, and mcr-5 genes with the phenotypic colistin resistance in isolates from diarrheal infants and children in Bangladesh. Bacteria were identified using the API-20E biochemical panel and 16s rDNA gene sequencing. Polymerase chain reac-tions detected mcr gene variants in the isolates. Their susceptibilities to colistin were determined by agar dilu-tion and E-test by minimal inhibitory concentration (MIC) measurements. Over 30.0% (69/225) of isolates showed colistin resistance by agar dilution assessment (MIC> 2.0 μg/mL). Overall, 15.5% of isolates carried mcr genes (7, mcr-1; 17, mcr-2; 13, mcr-3; and co-occurrence occurred in 2 isolates). Clinical breakout MIC val-ues (≥ 4 μg/mL) were associated with 91.3% of mcr-positive isolates. The mcr-positive pathogens include twenty Escherichia spp., five Shigella flexneri, five Citrobacter spp., two Klebsiella pneumoniae, and three Pseudo-monas parafulva. mcr-genes appeared to be significantly associated with phenotypic colistin resistance phe-nomena (p=0.000), with 100% colistin-resistant isolates showing MDR phenomena. Age and sex of patients showed no significant association with detected mcr variants. Overall, mcr-associated colistin-resistant bacte-ria have emerged in Bangladesh, which warrants further research to determine their spread and instigate ac-tivities to reduce resistance.

Medical waste management is crucial issues for keeping our life safe and safety. Without effective measures for waste management, we cannot keep ourselves safe from different types of contagious diseases; viruses, bacteria. Knowledge sharing assists healthcare staff in identifying and mitigating hazards on appropriate handling, segregation and disposal medical waste. The aim of the study is to identify a multifaceted analysis of knowledge sharing, training, communication and attitudes for effective medical waste management. This study selected 153 medical workers randomly, including nurses, lab technologists, and cleaners, from hospitals, diagnostic centers, and clinics in the northern part of Bangladesh. The study design of this research is mixed-methods. This research adopts a survey and interview as a research strategy. The samples are collected randomly. SPSS software packages, MS Excel Office, and PLS-SEM are used to analyze data. Most of the respondents always share their knowledge face-to-face according to the findings. The result also shows that there are positive relationship between sources of knowledge (p: 0.046), awareness and knowledge (p: 0.049), attitudes of waste management (p: 0.025) and effective medical waste management. However, there are no relationships between communication and collaboration (p: 0.943), the practice of waste management (p: 0.155), supervision and staff monitoring (p: 0.527), training and education (p: 0.656) and effective medical waste management. Its focus on the northern part of Bangladesh introduces regional specificity, potentially limiting the applicability of results to other regions. The knowledge-sharing practices for waste management among medical staff are examined within this research, along with the relationship between attitude, awareness, and knowledge, staff supervision and monitoring, practice, training, and education and effective medical waste management that have not been studied before home and abroad. This analysis highlights the critical need for an integrated approach to medical waste management, emphasizing the importance of continuous education, open communication, and cultivating a culture that prioritizes environmental sustainability. The insights from this study offer practical recommendations for healthcare institutions to improve their medical waste management practices, ultimately leading to enhanced health outcomes and better environmental protection.

SDG target 12.3 calls for halving food waste at retail, food service, and household by 2030. The food waste index for this purpose includes parts attached to food that are usually removed intentionally ("unavoidable food waste") and allows counting the conversion to animal feed and utilisation as biomaterial as means of reduction. In Japan, the "Food Waste Recycling Law" which has been in effect since 2001, promotes the recycling of food waste generated from businesses, designating feed conversion as top priority. On the other hand, based on the more recent "Food Loss Reduction Promotion Act" of 2019, the government is currently promoting the reduction of avoidable food waste, as to meet the SDG target. Based on statistical sources and interviews with Ministry officers, this paper explains the history and achievements of Japan's 23-year policy based on the Food Recycling Law, as well as the tension between the two legislations.

Currently, with the rapid growth of the population, the demand for metals has increased, especially for the manufacture of electronic devices such as cell phones, computer equipment, among others. Once these devices stop working, most are sent to landfills, which represents a danger since these wastes contain metals and other materials that must be properly managed to prevent them from having a negative effect on the environment and the human being. On the other hand, e-waste contains valuable metals such as copper, gold, and silver, the concentration of which in these materials makes it cost-effective to recover. This paper presents a review of the extraction and recovery of valuable metals from electronic waste by hydrometallurgical methods, as well as patents and industrial processes related to the management and treatment of this waste.

Since the process of waste recycling generates dust and flammable gas during fragmentation, there is always a risk of fire resulting therefrom, and fire does, in fact, frequently occur. However, research on disaster management at recycling facilities deals only with the problem of processing systems from a technical point of view, but it does not suggest concrete alternatives from a management point of view. Therefore, in this study, we analyzed the influence of the disaster response network of a waste recycling center at the organizational level based on the concept of the cognitive accuracy of a network when considering administrative aspects. Through this analysis, we confirmed that factors affecting the influence of the network exist, such that the entire network and the networks of different levels of position are different. We suggest that this can be improved by deploying members who perform formal tasks at the center of the network so that everyone can agree political approach.

Solid waste management is a major environmental challenge, especially in developing countries, with increasing amounts of waste glass (WG) and waste plastics (WP) not being recycled. In Ethiopia, managing WG and WP requires innovative recycling techniques. This study examines concrete properties with WG and WP as partial replacements for fine aggregate. Tests were conducted on cement setting time, workability, compressive strength, splitting tensile strength, and flexural strength. Concrete grade C-25, with a compressive strength of 25 MPa, was prepared using an optimum ratio of 14% WG and 6% WP. Mechanical properties were tested at 7 and 28 days of curing. At 20% replacement, workability decreased at water-cement ratios of 0.5 and 0.6 but remained stable at 0.4. Thus, a 0.4 ratio was used. For 10% replacement, compressive strength increased by 12.55% and 6.44% on the 7th and 28th days, respectively. At 20% replacement, compressive strength decreased by 14.35% and 0.73% on the 7th and 28th days, respectively. On the 28th day, splitting tensile strength at optimum replacement was 4.3 MPa, an 8.5% reduction from the control mix. However, flexural strength increased by 19.7%, from 12.46 MPa to 15.52 MPa. Overall, WG and WP improved flexural strength but slightly reduced splitting tensile strength.

In recent years, with the increasing research and development of the LED industry which contains GaN, it is expected that there will be a large amount of related wastes in the future. Especially the gallium has extremely high value of economic, therefore, it is necessary to establish the recycling system of the GaN waste. However, GaN is a direct-gap semiconductor and with high energy gap, high hardness, and high melting point make it difficult to recycle. Therefore, this study will analyze the physical characteristics of LED wastes containing GaN and carry out various leaching method to leach the valuable metals from the waste optimally. Different acids are used to find out the best reagent for leaching the gallium. Different experimental parameters are discussed such as the effect of the different acid agents , concentration, pressure, solid-liquid mass ratio, temperature, and time which influence the leaching efficiency of the gallium. In this study, various leaching methods which effect the leaching efficiency of the gallium are compared and the advantages and disadvantages are discussed. Finally, pressurized acid leaching method is preferred to leach the GaN waste, and hydrochloric acid is used as the leaching solution because of its better leaching efficiency of gallium. Eventually, the leaching efficiency of the gallium can reach to 98%.

This review paper highlights feasible and practicable approaches for managing end-of-life rolling stocks. It aims to promote and enable sustainable procurement policy for rolling stocks. Firstly, it demonstrates that modern rolling stocks can potentially gain the environmental benefits since almost all of their materials used in the rolling stock manufacturing can be recycled and reused. In this study, brief definition and concept of various train types are introduced and discussed, accompanied by some demonstrative illustrations. Then, component analyses, recovery rates and percent proportion of each material in various rolling stock assemblies have been evaluated. The estimation of material quantities that can potentially be recycled has been carried out using industry data sources. The suitable management procedures for end-of-life rail vehicles are then discussed, together with the life cycle of the key materials in which the recyclability criteria take into account the environmental risks and the best and safest approaches to deal with them. The aim of this study is to increase the awareness of the public, train manufacturers and rail industries on the benefits to the environments from rolling stock recycling, which could result in sustainable society and urban livings.