The twisted Wang transform distribution family, defined as the composition of parameter shifted inverse CDF function with an original CDF function, is found to be most suitable for matching low shape factor distributions, characterizing hard to fit or to simulate reinsurance portfolio losses for some perils from our previous study. Among them, the best form for matching a hard-to-fit empirical loss distribution for a specific peril, is the Exponential Fractional Extra Power 0 Distribution in (0,1) with CDF:.The simplest yet still a good form of this family is the Transformed Hyperbolic Tangent Distribution with CDF:,which has analytical formulas for the moments. The twisted Wang transform distribution family is compared and confirmed to be superior to all other well-known distribution families through extensive numerical optimization practice, distribution forms guesses, and computer-aided exploration experiments.

The two-phase flow of water and reactive gas in the channel of proton exchange membrane fuel cell (PEMFC) plays an important role in high-quality water management. In this study, the removal effect of 3D wave channel and 2D straight channel for liquid water was studied by volume of fluid method. The dynamic behavior of droplet emerge from the gas diffusion layer (GDL) into the channel under the influence of gas flow was investigated. The effects of droplet growth, deformation, detachment, force, pore size on water critical behavior and water content in the channel are discussed. The results show that the 3D wave channel is superior to the removal of liquid water than the 2D straight channel. The increase of velocity is conducive to the discharge liquid water. While infinite increase of velocity will cause more parasitic power loss. The larger pore size of GDL is not advantageous to the performance of PEMFC, but the appropriate increase of pore size is conducive to the discharge of liquid water. The basic knowledge obtained in this study will help to deepen the understanding of droplet dynamics in PEMFC gas channels, and help to optimize the design and working conditions of these channels.

To overcome the difficulty of separating bastnaesite from fluorite through the flota-tion technique, the present study examined the suitability of sodium alginate (SA) as a depressant in the flotation process. The effect of SA on the flotation separation of bastnaesite and fluorite was evaluated using micro-flotation tests, zeta potential meas-urements, adsorption density measurements, Fourier infrared spectroscopy, and X-ray photoelectron spectroscopy. The micro-flotation results showed that SA exerted a strongly detrimental effect on fluorite flotation, while slightly affecting bastnaesite flotation. The surface chemistry results revealed that the -COO- and HO- functional groups in SA coordinated with Ca2+ on the fluorite surface, which induced hydro-philicity and hindered the adsorption in the subsequent collector. However, the inter-action of SA with the bastnaesite surface was marginal and did not affect the anchor-ing of the collector on the surface of bastnaesite. Based on these results, the present study proposes a possible model for the interaction of SA on the surfaces of the two minerals, laying a foundation for the flotation separation of bastnaesite from fluorite with SA as an environmentally benign depressant.

An abdominal aortic aneurysm (AAA) is usually asymptomatic until rupture, which is associated with extremely high mortality. Consequently, early detection of AAAs is of paramount importance in reducing mortality; however, most AAAs are detected by medical imaging incidentally. The aim of this study was to investigate the feasibility of machine learning-based pulse wave (PW) analysis for the early detection of AAAs using a database of in silico PWs. PWs in the large systemic arteries were simulated using one-dimensional blood flow modelling. A database of in silico PWs representative of subjects (aged 55, 65 and 75 years) with different AAA sizes was created by varying the AAA-related parameters with major impacts on PWs – identified by parameter sensitivity analysis – in an existing database of in silico PWs representative of subjects without AAA. Then, a machine learning architecture for early detection of AAAs was proposed, which was trained and tested using the new in silico PW database. The parameter sensitivity analysis revealed that the AAA maximum diameter and stiffness of the large systemic arteries were the dominant AAA-related biophysical properties that significantly influence the PW. The simulated PW indexes extracted from the database showed that the PW was not only influenced by the presence of an AAA but was also significantly affected by multiple cardiovascular parameters that compromised the detection of AAAs by using individual PW indexes. Alternatively, the trained machine learning model performed well in classifying normal and AAA conditions using digital photoplethysmogram PWs from the database. These findings suggest that machine learning-based PW analysis is a promising approach for AAA screening using PW signals acquired by wearable devices.

Long-term storage may reduce the nutritional quality of brown rice, so the present study was aimed to evaluate the nutritive values and application in pig diets. In Exp.1, 18 Landrace × Yorkshire (L × Y) barrows with initial body weight (IBW) of 25.48 ± 3.21 kg were randomly assigned to three treatments, which included corn diet, one-year stored brown rice (BR1) diet and six-year stored brown rice (BR6) diet, to determine the digestible energy (DE) and metabolisable energy (ME) value of stored brown rice. In Exp. 2, 24 barrows (L × Y; IBW: 22.16 ± 2.42 kg) fixed with ileal T-cannula were randomly allotted to four dietary treatments, including corn diet, two stored brown rice diets and nitrogen-free diet, to evaluate the amino acid (AA) digestibility of stored brown rice. In Exp. 3 and 4, 108 crossbred weaned piglets (L × Y; IBW: 9.16 ± 0.89 kg) and 90 crossbred growing pigs (L × Y; IBW: 48.28 ± 3.51 kg) were allotted to 3 treatment diets, including control diet and two stored brown rice diets, respectively, to investigate the application of stored brown rice in weaned piglet and growing-finishing pig diets. Results showed that: 1) The DE and ME of corn and stored brown rice showed no significant differences (P > 0.05), while the apparent ileal digestibility (AID) of arginine, histidine, aspartic acid, and the standardized ileal digestibility (SID) of arginine and histidine were higher in stored brown rice compared to corn (P < 0.05). 2) Compared with the control diet, the stored brown rice diets showed no significant effects on growth performance, nutrient apparent total tract digestibility (ATTD) and serum biochemical indices (P > 0.05), but decreased digestive enzymes activities in duodenum, jejunum and ileum of piglets (P < 0.05). 3) Compared with the control diet, the stored brown rice diets showed no significant effects on growth performance, carcass traits, meat quality, fatty acids profiles in the longissimus dorsi muscle of growing-finishing pigs (P > 0.05). In conclusion, the brown rice stored for 6 years under good conditions has no obvious changes in available energy and nutrient values. Although it may reduce digestive enzyme activity in small intestine of the piglets, the stored brown rice showed no obvious adverse effect on growth performance and meat quality, and can be effectively used in pig diet.

Fundus image registration plays a crucial role in the clinical evaluation of ocular diseases, such as diabetic retinopathy and macular degeneration, necessitating meticulous monitoring. The alignment of multiple fundus images enables the longitudinal analysis of patient progression, widening the visual scope, or augmenting resolution for detailed examinations. Currently, prevalent methodologies rely on feature-based approaches for fundus registration. However, certain methods exhibit high feature point density, posing challenges in matching due to point similarity. This study introduces a novel fundus image registration technique integrating U-Net for the extraction of feature points employing FIVES for its training and evaluation, a novel and large dataset for blood vessels segmentation, prioritizing point distribution over abundance. Subsequently, the method employs medial axis transform and pattern detection to obtain feature points characterized by the Fast Retina Keypoint (FREAK) descriptor, facilitating matching for transformation matrix computation. Assessment of the vessel segmentation achieves 0.7559 for Intersection Over Union (IoU), while evaluation on the Fundus Image Registration Dataset (FIRE) demonstrates the method’s comparative performance against existing methods, yielding a registration error of 0.596 for area under the curve, refining similar earlier methods and suggesting promising performance comparable to prior methodologies.

Uncertain fractional differential equation (UFDE) is an excellent tool for describing complicated dynamic systems. This paper analyzes the valuation problems of currency option based on UFDE under optimistic value criterion. Firstly, an uncertain fractional currency model is formulated to describe the dynamics of foreign exchange rate. Then, the pricing formulae of European, American and Asian currency option are obtained under optimistic value criterion, respectively. Finally, numerical simulations are provided to illustrate the validity of our theoretical results.

For screening excellent lactic acid bacteria (LAB) strains to inhibit Escherichia (E.) coli (ETEC) K88, inhibitory activities of more than 1100 LAB strains isolated from different materials and kept in the lab were evaluated in this study. Nine strains with inhibition zone at least 22.00 mm (including that of hole puncher 10.00 mm) and good physiological and biochemical characteristics identified by 16S DNA gene sequencing and recA gene multiple detection, were assigned to Lactobacillus (L.) plantarum subsp. plantarum (5), L. fermentum (1), L. reuteri (1), W. cibaria (1) and E. faecalis (1), respectively. As investigated for their tolerance abilities and safety, only strain ZA3 possessed high hydrophobicity and auto-aggregation abilities, had high survival rate in low pH, bile salt environment and GI fluids, sensitive to ampicillin, resistant to norfloxacin and amikacin, without hemolytic activity and didn’t carry antibiotic resistance genes, exhibited broad spectrum activity against a wide range of microorganisms, and antibacterial substance may attribute to organic acids, especially lactic acid and acetic acid. The results indicated that the selected strain L. plantarum subsp. plantarum ZA3 could be considered a potential probiotic to inhibit ETEC K88 for further research.

Satellite-based monitoring can retrieve ground-level PM_2.5 concentrations with higher-resolution and continuous spatial coverage to assist in making management strategies and estimating health exposures. The Sichuan Basin has a complex terrain and several city clusters that differ from other regions in China: it has an enclosed air basin with a unique planetary boundary layer dynamic which accumulates air pollution. The spatiotemporal distribution of 1-km resolution Aerosol Optical Depth (AOD) in the Sichuan Basin was retrieved using the improved dark pixel method and Moderate Resolution Imaging Spectroradiometer (MODIS) data in this study. The retrieved seasonal AOD reached its highest values in spring and had the lowest values in autumn. The higher correlation (r = 0.84, N = 171) between the ground-based Lidar AOD and 1-km resolution MODIS AOD indicated that the high-resolution MODIS AOD could be used to retrieve the ground-level PM_2.5 concentration. The Lidar-measured annual average extinction coefficient increased linearly with the Planetary Boundary Layer Height (PBLH) in the range of 100 ~ 670 m, but exponentially decreased between the heights of 670 ~ 1800 m. Both the correlation and the variation tendency of simulated PBLH from WRF_SHIN/CALMET were closer to the Lidar observation than that of three other Planetary Boundary Layer (PBL) schemes (the Grenier-Bretherton-McCaa (GBM) scheme, the he Total Energy-Mass Flux (TEMF) scheme and the University of Washington (UW) scheme), which suggested that the simulated PBLH could be used in the vertical correction of retrieval PM_2.5. Four seasonal fitting functions were also obtained for further humidity correction. The correlation coefficient between the aerosol extinction coefficient and the fitted surface-level PM_2.5 concentration at the benchmark station of Southwest Jiao-tong University was enhanced significantly from 0.62 to 0.76 after vertical and humidity corrections during a whole year. During the evaluation of the retrieved ground-level PM_2.5 with observed values from three cities, Yibin (YB), Dazhou (DZ), and Deyang (DY), our algorithm performed well, resulting in higher correlation coefficients of 0.78 (N = 177), 0.77 (N = 178), and 0.81 (N = 181), respectively.

The effects of 1%~5% cold compression on the mechanical properties, microstructure and residual stress of 7050 aluminum alloy were investigated, and the results were applied to the complex die forging with stiffener structure. The results show that with the increase of cold compression, the tensile strength of forging decreases gradually, but the conductivity and fracture toughness of the forging have little change. TEM microstructure shows that with larger cold compression (5%), the dislocation density was relatively higher, which promoted the precipitation and growth of precipitated phases at positions with higher dislocation density during aging process. The ultrasonic tests of residual stress show that with the increase of cold compression, the residual stress in the forging decreases first, and then increases when cold compression reaches 5%. The results of the die forging of 7050 aluminum alloy with bar structure show that the residual stress of the die forging is obviously eliminated after 2-4% cold compression, and the deformation after machining is obviously less than of the uncompressed forgings. The combination of bar and web is more beneficial to the uniform distribution of residual stress of the die forging with bar structure.

The manuscript reported the synthesis of Al2O3 nano-coating onto quartz fiber by plasma electrolysis spray for enhanced thermal conductivity and stability. The nano- and micro-sized clusters were partially observed on the coating, while most coating was relatively smooth. It was suggested that the formation of a ceramic coating was followed as the nucleation-growth raw, that is, the formation of the coating clusters was dependent on the fast grow-up partially, implying the inhomogeneous energy distribution in the electrolysis plasma. The deposition of the Al2O3 coating increased the annealing tensile strength from 19.2 MPa to 58.1 MPa. The thermal conductivity of the coated quartz fiber was measured to be 1.17 W m-1 K-1, increased by ~45% compared to the bare fiber. The formation mechanism of the Al2O3 coating was preliminarily discussed. We believe that the thermally conductive quartz fiber with high thermal stability by plasma electrolysis spray will find a wide range of applications in industries.

The geographical location of Yunnan province is at the upstream area of water vapor transportation from the Bay of Bengal and the South China Sea to inland China. Understanding the spatiotemporal variations of water vapor over this region holds significant importance. We utilized the GNSS data collected from 12 stations situated in Yunnan, which are part of Crustal Movement Observation Network of China, to retrieve hourly precipitable water vapor (PWV) from 2011 to 2022. The retrieved PWV at Station KMIN were evaluated by the nearby radiosonde data, and the result shows that the mean bias and RMS of the differences between the two datasets are 0.08 and 1.78 mm respectively. Average PWV values at these stations are in the range of 11.77 to 33.53 mm, which decrease from the southwest to the north of Yunnan and are negatively correlated with the station heights and latitudes. Differences between average PWV in wet season and dry season range from 12 to 27 mm. These differences tend to increase as the average PWV increases. The yearly rates of PWV variations, averaging 0.18 mm/year, are all positive for the stations, indicating a year-by-year increase in water vapor. Amplitudes of the PWV annual cycles are 9.75-20.94 mm. The spatial variation of these amplitudes is similar to that of average PWV over the region. Generally, monthly average PWV values increase from January to July and decrease from July to December, and the growth rate is less than the decline rate. Average diurnal PWV variations show unimodal PWV distributions over the course of the day at the stations except Station YNRL, where bimodal PWV distribution was observed.

Lanthanide-doped upconversion nanoparticles (UCNPs) are promising bioimaging nanoprobes due to their excellent photostability. As one of the most commonly-used lanthanide activators, Tm3+ ions have perfect ladder-type electron configuration and can be directly excited by bio-friendly near-infrared-II (NIR-II) wavelengths. Here, the emission characteristics of Tm3+-doped nanoparticles under laser excitations of different near-infrared-II wavelengths were systematically investigated. The 1064 nm, 1150 nm and 1208 nm lasers are proposed to be three excitation strategies with different response spectra of Tm3+ ions. Particularly we found that 1150 nm laser excitation enables intense three-photon 475 nm emission, which is nearly 100 times stronger than that excited by 1064 nm excitation. We further optimized the luminescence brightness after investigating the luminescence quenching mechanism of bare NaYF4:Tm (1.75%) core. After growing inert shell, ten-fold increase of emission intensity was achieved. Combining the advantages of NIR-II wavelength and the higher-order nonlinear excitation, a promising facile excitation strategy was developed for the application of thulium-doped upconversion nanoparticles in single nanoparticle imaging and cancer cell microscopic imaging.

Abstract Objective：To explore the efficacy of modified Altemeier procedure in the treatment of complete rectal prolapse. Method and Main outcome measures:The enrolled patients with complete rectal prolapse were divided into traditional and modified groups according to the surgical approach.The primary outcomes included complication rates, time and severity of postoperative recurrence, changes in pre- and postoperative Wexner anal incontinence scores and ED-5Q-5L quality-of-life autonomy scores. Secondary outcomes included operative time, intraoperative bleeding, and length of hospital stay. Results:The overall complication rates were 33.33% and 6.67% and recurrence rates were 26.67% and 7% in the traditional and modified groups, respectively (P<0.05)；The duration of surgery in the traditional group was shorter than that in the modified group, but the intraoperative bleeding was significantly higher than that in the modified group, and all differences were statistically significant (P<0.05)；The length of stay and in the two groups, respectively, with no statistically significant difference (P>0.05)；The postoperative Wexner incontinence score and ED-5Q-5L quality of life in the modified group were found to be significantly better than those in the traditional group at 8 months postoperative follow-up, with statistically significant differences (P<0.05). Conclusions:Pathological dilatation of the distal rectum may be another anatomical defect in complete rectal prolapse. The results of the clinical study confirmed the clinical effectiveness and safety of the modified Altmeyer procedure, which has high clinical application value.

The latest methods based on deep learning have achieved amazing results regarding the complex work of inpainting large missing areas in an image. This type of method generally attempts to generate one single "optimal" inpainting result, ignoring many other plausible results. However, considering the uncertainty of the inpainting task, one sole result can hardly be regarded as a desired regeneration of the missing area. In view of this weakness, which is related to the design of the previous algorithms, we propose a novel deep generative model equipped with a brand new style extractor which can extract the style noise (a latent vector) from the ground truth image. Once obtained, the extracted style noise and the ground truth image are both input into the generator. We also craft a consistency loss that guides the generated image to approximate the ground truth. Meanwhile, the same extractor captures the style noise from the generated image, which is forced to approach the input noise according to the consistency loss. After iterations, our generator is able to learn the styles corresponding to multiple sets of noise. The proposed model can generate a (sufficiently large) number of inpainting results consistent with the context semantics of the image. Moreover, we check the effectiveness of our model on three databases, i.e., CelebA, Agricultural Disease, and MauFlex. Compared to state-of-the-art inpainting methods, this model is able to offer desirable inpainting results with both a better quality and higher diversity. The code and model will be made available on https://github.com/vivitsai/SEGAN.

As the largest accretionary orogen in the world, the Central Asian Orogenic Belt (CAOB) has continuous juvenile crustal growth in the Phanerozoic. The northern margin of the North China Craton(NCC) and its adjacent area is the eastern segment of the CAOB, and is a key area to study the geological evolution of Paleo-Asian Ocean (PAO). In the Permian, the west of the northern margin of NCC belongs to a post-collision extensional environment, and the east belongs to a subduction stage. But, As a connecting area, the Permian evolution of PAO in the middle of northern margin of NCC has not been systematically studied. In order to fill the blank and understand the temporal and spatial continuous evolution process of PAO, this paper focused on the Permian granitic rocks in the Chifeng area, zircon U-Pb dating and the geochemical analysis of the whole rock main and trace elements were conducted in order to build a granite chronological framework, discuss the genesis and tectonic background of the granite rocks as well as the magma-tectonic evolution history in the Chifeng area. Zircon U-Pb dating results of 8 samples are 269±1 Ma, 268±3 Ma, 260±4 Ma, 260±1 Ma, 260±1 Ma, 255±2 Ma, 254±2 Ma, 256±1Ma, which showed that the Permian granitic rocks had undergone three stages of emplacement: (1) The monzogranite and syenite (294-284 Ma); (2) The monzogranite (269-260Ma) and (3) The monzogranite and syenite (256-254Ma). The Middle Permian magmatism (269-260Ma) was represented by the monzogranite assemblages with different grain sizes. The geochemical characteristics showed that they were high-potassium calc-alkaline-potassium dossonite series of granites formed in compressional environment, indicating there was a collision between the Xing’an-Mongolian Orogenic Belt (XMOB) and the North China Craton (NCC). During the Late Permian-Early Triassic (256-248Ma), the granites in the Chifeng area are dominated by the A-type and I-type granites of high-potassium calc-alkaline series formed under an extensional environments, which constituted typical "bimodal" rock assemblage combined with the coeval basic rocks, suggesting the study area was in an extensional environment where the subducting slab is fragmented during the collision between the XMOB and the NCC. According to emplacement time and occurrence location, the plutons are interpreted to have been generated by the subduction-collision of the Paleo-Asian oceanic crust beneath the NCC. This study provides strong evidence for Permian tectonic evolution and the characterization of the eventual closure of the Paleo-Asian Ocean in the Chifeng City at the northern margin of the NCC.

The content of magnesium ions (Mg2+) in drinking water is relatively high and the excessive Mg2+ ingestion may lead to pathological lesions in human body system. At present, the detection of Mg2+ still relies on costly devices or/and complex organic fluorescence probes. To solve this problem, this work proposed a NaBH4-mediated co-reduction strategy for the synthesis of glutathione-stabilized bimetallic AuAg nanoclusters (GSH@AuAg NCs) with recognition performance to Mg2+. The preparation of GSH@AuAg NCs was simple and rapid and could be performed at mild conditions. The reaction parameters and sampling orders were optimized to understand the formation mechanism of GSH@AuAg NCs. The GSH@AuAg NCs exhibited a sensitive “light-on” fluorescence response to Mg2+ due to the re-molding of the interfacial physicochemical environment following the Mg2+ coordination, which affected the surface charge transfer process, and thus led to a novel method for fluorescence detection of Mg2+ with admirable selectivity for Mg2+. The proposed method showed a detection limit of 0.2 μM, and its practical utility for the detection of Mg2+ in real sample of purified drinking water was also demonstrated, confirming its practicability in monitoring the Mg2+ concentration in drinking water.

This study was aimed to investigate the effect of xylan depolymerizing enzyme namely endo-xylanase (Xyn) combined with debranching enzymes namely arabinofuranosidase (Afd) and feruloyl esterase (FE) on digestion, growth performance and intestinal volatile fatty acid profile of piglets. The in vitro experiments were firstly conducted to examine the enzymological properties of Xyn, Afd and FE, the synergy among these enzymes, together with the effect of combination of these enzymes on digestion of piglet diet. The in vivo experiment was then implemented by allocating 270 35-d-old postweaning piglets into 3 treatment groups: control group, Xyn group and (Xyn+Afd+FE) group. Each group had 6 replicates (15 piglets/replicate). The results revealed a satisfying thermostability and pH stability of Xyn, Afd and FE. Combination of Xyn, Afd and FE had a superiority (P < 0.05) over Xyn alone and its combination with Afd or FE in promoting degradation of different bran fibers rich in arabinoxylan (Abx). Treatment with combination of Xyn, Afd and FE had advantages over Xyn alone to induce increasing trends (P < 0.10) of in vitro digestibility of dietary nutrients (dry matter, crude protein, crude ash and gross energy) and piglet growth performance (average daily gain, final body weight and feed efficiency), concurrent with a reduction (P < 0.05) of diarrhea rate and increases (P < 0.05) in cecal acetic acid, butyric acid and total volatile fatty acids concentrations as well as pH value of piglets. Collectively, combination of Xyn, Afd and FE was efficient in benefiting degradation of Abx in brans, as well as improving digestion, growth performance and intestinal volatile fatty acid profile of piglets.

Artistic image completion is fundamental for the preservation and restoration of invaluable art paintings and it has experienced significant progress through the implementation of deep learning methodologies. Despite these advancements, challenges persist, even with sophisticated approaches like Generative Adversarial Networks (GANs), particularly in achieving optimal results for high-resolution paintings. Small-scale texture synthesis and the inference of missing information from distant contexts present persistent issues, leading to distortions in lines and unnatural colors, especially in art paintings with complicated structures and textures. Concurrently, patch-based image synthesis has evolved by incorporating global optimization on the image pyramid to enhance structural coherence and details. However, methods relying on gradient-based synthesis encounter obstacles related to directionality, inconsistency, and the heavy computational burdens associated with solving the Poisson equation in non-integrable gradient fields. This paper introduces a groundbreaking approach, integrating Weighted Similarity-Confidence Laplacian Synthesis, to comprehensively address these challenges and advance the field of artistic image completion. This proposal addresses challenges not only in high-resolution artistic image completion but also makes a significant contribution to the broader field of patch-based synthesis by utilizing the Laplacian pyramid for enhanced edge-aware correspondence search. Experimental result confirms the effectiveness of our approach, offering promising outcomes for the preservation and restoration of art paintings with complicated details and irregular missing regions.

COVID-19 patients can recover with a median SARS-CoV-2 clearance of 20 days post initial symptoms (PIS). However, we observed some COVID-19 patients with existing SARS-CoV-2 for more than 50 days PIS. This study aimed to investigate the cause of viral clearance delay and the infectivity in these patients. Demographic data and clinical characteristics of 22 long-term COVID-19 patients were collected. SARS-CoV-2 nucleic acid, peripheral lymphocyte count, and functionality were assessed. SARS-CoV-2-specific and neutralization antibodies were detected, followed by virus isolation and genome sequencing. The median age of the studied cohort was 59.83±12.94 years. All patients were clinically cured after long-term SARS-CoV-2 infection ranging from 53 to 112 days PIS. Peripheral lymphocytes counts were normal. Interferon gamma (IFN-ƴ)-generated CD4+ and CD8+ cells were normal as 24.68±9.60% and 66.41±14.87%. However, the number of IFN-ƴ-generated NK cells diminished (58.03±11.78%). All patients presented detectable IgG, which positively correlated with mild neutralizing activity (ID50=157.2, P=0.05). SARS-CoV-2 was not isolated, and a cytopathic effect was lacking. Only three synonymous variants were identified in spike protein coding regions. In conclusion, decreased IFN-γ production by NK cells and low neutralizing antibodies might favor SARS-CoV-2 long-term existence. Further, low viral load and weak viral pathogenicity was observed in COVID-19 patients with long-term SARS-CoV-2 infection.

As construction costs continue to rise and adequate amounts of funding continues to be a challenge, the allocation of resources is of critical importance when it comes to the maintenance and rehabilitation (M&R) of highway infrastructure. A Life Cycle Assessment (LCA) methodology is presented here that integrates realistic traffic conditions in the operational phase to compare M&R scenarios over the analysis period of a 26-km stretch of Interstate-495. Pavement International Roughness Index (IRI) were determined using AASHTO’s PavementME System. Meanwhile, vehicle fuel consumption and emission factors were calculated using a combination of Google Maps®, the U.S. EPA’s Motor Vehicle Emission Simulator, the SHRP2 Naturalistic Driving Study, and MassDOT’s Transportation Data Management System. The evaluation of pavement performance with realistic traffic conditions, varying M&R strategies and material characteristics was quantified in terms of Life Cycle Cost (LCC), Global Warming Potential (GWP) and Cumulative Energy Demand (CED) for both agencies and users. The inclusion of realistic traffic conditions into the use phase of the LCA resulted in a 6.4% increase in CED and GWP when compared to baseline conditions simulated for a week long operation duration. Results from this study show that optimization of M&R type, material selection and timing may lead to a 2.72% decrease in operations cost and 47.6% decrease in construction/maintenance costs.

Considering the spectrum shortage problem of IoT devices, we introduce a collaborative spectrum sensing (CSS) framework in this paper to identify available spectrum resources, so that IoT devices can access it and meanwhile avoid causing harmful interference to the normal communication of the primary user (PU). However, in the process of the PU’s signal detection in IoT devices, the issue about the stopping time and decision cost arises. To this end, we propose a distributed cognitive IoT model, which includes two IoT devices independently using sequential decision rules to detect the PU. On this basis, we define the stopping time and cost function for IoT devices, and formulate an average cost optimization problem in CSS. To solve this problem, we further regard the optimal stopping time problem as a finite horizon problem, and solve the threshold of the optimal decision rule by dynamic programming. At last, numerical simulation results demonstrate the correctness of our proposal in terms of the global false alarm and miss detection probability, and it always achieves minimal average cost under various cost of each observation taken and thresholds.

The alignment of nanostructures in materials such as lyotropic liquid crystals (LLCs) templated materials has the potential to signicantly improve their performances. However, accurately characterising and quantifying the alignement of such fine structures remains very challenging. In situ small angle X-ray scattering (SAXS) and molecular dynamics were employed for the first time to understand the hexagonal LLC alignment process with magnetic nanoparticles under a magnetic field. The enhanced alignment has been illustrated from the distribution of azimuthal intensity in the samples exposed to magnetic field. Molecular dynamics simulations reveal the relationship between the imposed force of the magenetic nanoparticles under magnetic field and the force transferred to the LLC cylinders which leads to the LLC alignment. The combinational study with experimental measurement and computational simulation will enable the development and control of nanostructures in novel materials for various applications.

Evidence indicates that the long noncoding RNAs are involved in the metformin-mediated anti-cancer processes. However, the potential effects of the long noncoding RNAs in metformin-mediated anti-tumor processes in esophageal squamous cell carcinomas (ESCC) are still elusive. This study uncovered that metformin decreases the level of long noncoding RNAs CCAT1 and SPRY4-IT1 thereby contributing to the down-regulation of c-Myc and vimentin. Also, the RNA level test of human ESCC tissue confirmed the positive correlation between CCAT1 and c-Myc. These findings demonstrated that metformin facilitated anti-cancer effects by targeting the 2 long noncoding RNAs (CCAT1 and SPRY4-IT1) and their consequential targets c-Myc and vimentin. Therefore, the CCAT1 and SPRY4-IT1 might act as novel molecular targets that mediate the anti-tumor effects in esophageal squamous cell carcinoma. This helps in predicting the treatment response of metformin in patients diagnosed with esophageal squamous cell carcinoma.

The surface electromyogram (sEMG)--based gesture recognition to the development of intelligent prostheses has emerged as a promising avenue for upper limb amputees. However, the temporal variations in sEMG have rendered recognition models less efficient than anticipated. Cross-session calibration and training data indicate the capacity to reduce this variation. The impact of varying calibration and training data amounts on gesture recognition performance for amputees is still unknown. To assess these effects, we present four datasets for the evaluation of calibration data and examine the impact of training data volume on benchmark performance. Two amputees who had undergone amputations years prior were recruited and seven sessions of data were collected for analysis from each of them. The experimental results show that the calibration data improved the average accuracy per subject by 3.03% and 6.16%, respectively, compared to the baseline results. Moreover, it was found that to collect training data for modeling, boosting the number of training sessions proves more efficient than increasing the number of trials within a single session. Two potentially effective strategies are proposed in light of this research to enhance the cross-session models further. We consider these findings to be of the utmost importance for the commercialization of intelligent prostheses, as they demonstrate the criticality of gathering calibration and cross-session training data, as well as offer effective strategies for maximizing the utilization of the entire dataset.

Background: Previous in vitro and in vivo studies have demonstrated that storage of cooked rice at 4 °C for 24 h and reheating to 65 °C significantly reduced starch digestibility and postprandial glycaemic responses. Moreover, the effect was greater for parboiled rice compared to other rice varieties commonly consumed in New Zealand. This study aimed to evaluate consumer preferences of related sensory attributes and consumer acceptability of several rice varieties freshly cooked or reheated. Method: Sixty-four consumers volunteered and recorded on Visual Analoge Scales their preference and acceptability of freshly prepared or cold-stored and reheated medium grain white, medium grain brown and parboiled rice. Results: All six rice samples were accepted by participants (average 54%). Reheated parboiled rice and reheated medium grain brown rice were both accepted by participants as a preferred staple meal compared to other rice samples. Among all rice samples, the sweetness and the flavour of freshly cooked warm medium-grain white rice were less preferred (scored 42.1% and 45.0% respectively) compared with other samples (P = 0.05). Participants who prepared and consumed brown rice at home regularly (more than 10 times per month), preferred the reheated brown rice (73.8% (67.4, 80.2)) and reheated parboiled rice (74.3% (67.9, 80.7)) (P < 0.001). Conclusions: It is suggested that reheated parboiled rice, with the lowest starch digestibility and glycaemic impact (both in vitro glucose release and in vivo glucose response) could be accepted as a healthier alternative for the daily staple meal.

Alternative splicing (AS) plays a crucial role in regulating gene expression, function and diversity. However, limited reports exist on identification and comparation of AS in Eastern and Western pigs. Here, we analyzed 243 transcriptome data from eight tissues, integrating information on transcription factors (TFs), selection signals, splicing factors (SFs), and QTLs to comprehensively study alternative splicing events (ASEs) in pigs. Five ASE types were identified, with Mutually Exclusive Exon (MXE) and Skipped Exon (SE) ASEs being the most prevalent. A significant portion of genes with ASEs (ASGs) showed conservation across all eight tissues (63.21% - 76.13% per tissue). Differentially alternative splicing genes (DASGs) and differentially expressed genes (DEGs) exhibited tissue specificity, with blood and adipose tissues having more DASGs. Functional enrichment analysis revealed coDASG_DEGs in adipose were enriched in pathways associated with adipose deposition and immune inflammation, while coDASG_DEGs in blood were enriched in pathways related to immune inflammation and metabolism. Adipose deposition in Eastern pigs might be linked to down-regulation of immune-inflammation-related pathways and reduced insulin resistance. The TFs, selection signals, and SFs appeared to regulate ASEs. Notably, ARID4A (TF), NSRP1 (SF), ANKRD12, IFT74, KIAA2026, CCDC18, NEXN, PPIG, and ROCK1 genes in adipose tissue showed potential regulatory effects on adipose-deposition traits. And NSRP1 could promote adipogenesis by regulating alternative splicing and expression of CCDC18. Conducting an in-depth investigation into AS, this study has successfully identified key marker genes essential for pig genetic breeding and the enhancement of meat quality, which will play important roles in promoting the diversity of pork quality and meeting market demand.

The performance consistency of an RF MEMS switch matrix is a crucial metric, which directly impacts its operational lifespan. An improved crossbar-based RF MEMS switch matrix topology, the SR-Crossbar, was investigated in this article. An optimized port configuration scheme was proposed for the RF MEMS switch matrix. Both the utilization probability of individual switch nodes and path lengths in the switch matrix achieve best consistency simultaneously under the proposed port configuration scheme. One significant advantage of this scheme lies in that it only adjusts positions of input and output ports, with topology and individual switch nodes kept unchanged. This grants it a high level of generality and feasibility, and also introduces an additional degree of freedom for optimizations. The article also constructed a universal utilization probability function of single nodes, and formulated an optimization objective function for the SR-Crossbar RF MEMS switch matrix, which provides a convenient approach to directly solving the optimized port configuration scheme for practical applications.

Understanding the spatial distribution pattern and evolution characteristics of the elderly population in urban areas is of great significance for the development of urban planning and the implementation of public management policies in the context of rapid aging. Accurately identifying the spatial distribution and evolution characteristics of the elderly population in the city requires a comprehensive analysis of multiple indicators and large-scale data. Taking Wuhan city as an example, this article measures the spatial distribution characteristics and evolution trend of the elderly population from 2000 to 2020 at the street/township level, based on the fifth, sixth, and seventh census data, using methods such as kernel density hotspot detection, spatial clustering analysis, and standard deviation ellipse analysis. The results show that: ① there are significant differences in the aging spatial pattern between the central area and the suburban areas of Wuhan; ② overall, Wuhan's aging rate shows a typical "core-periphery" growth mode in space, while the density of the elderly population has significant spatial aggregation characteristics and shows an evolution trend of "centralized concentration, peripheral outliers, axial development, and near-field growth"; ③the center of gravity of the elderly population remains relatively stable over time.

In this work, we propose a generalized partially functional linear model, which not only models the relationship between multiple scalar and functional predictors and response, but also automatically estimates the link function. Specifically, we use the functional principal component analysis method to reduce the dimensionality of functional predictors, estimate the regression coefficients using the maximum likelihood estimation method, estimate the link function using the method of local linear regression, iteratively obtain the final estimator, and prove the asymptotic normality of the estimator. The asymptotic normality is illustrated through simulation experiments. Finally, the proposed model is applied to study the influence of environmental, economic, and medical levels on life expectancy in China. In the study functional predictors are the daily air quality index, temperature, and humidity of 58 cities in 2020 and scalar predictors are GDP and number of beds in hospitals.

Grazing exclusion (GE) and rest grazing (RG) are important management to restore grassland ecosystems. In order to evaluate the effects and mechanisms of different grazing management on species diversity, vegetation community indices and soil variables were determined in the plots of Qilian Mountains in Gansu Province. The results showed that diversity effects and their regulating mechanisms had space-scale dependence under different grazing management. Species richness and species diversity indices of RG in grassland were significantly higher than that of GE at the regional scale. Additionally, three grazing management in mountain meadows had only a significant effect on species richness, but different management in mountain meadows and temperate steppes had a significantly different effect on species diversity indices. Meanwhile, soil variables only influenced species diversity at the regional scale. Most of community and soil variables at each scale had positive effects on species diversity, except that the direction of biodiversity effects was negative for species coverage, mean plant height, soil porosity (SK) and bulk density (BD) under two contrasting grazing management. In conclusion, choosing RG at the regional scale and select grazing management according to different grassland types at the local scale to restore degraded grassland vegetation.

Vibrio splendidus is the main pathogen infect a wide range of hosts, especially sea cucumber Apostichopus japonicus. Our previous studies had shown that the level of L-glutamic acid (L-Glu) was significantly increased under heat stress and it was one of the best carbon sources that could be used by V. splendidus AJ01. In this study, the effects of exogenous L-Glu on the coelomocyte viability, tissue status and individual mortality of sea cucumbers were analyzed. The results showed that 10 mM L-Glu decreased coelomocyte viability and increased mortality, with tissue rupture and pyknosis, while 0.1 mM L-Glu slightly affected the survival of sea cucumbers without obvious damages at both cellular and tissue levels. Transcriptomic analysis showed that there were 343 upregulated and 206 downregulated genes regulated by exogenous L-Glu. GO analysis showed that differentially expressed genes (DEGs) were mainly enriched in signaling and membrane formation, while KEGG analysis showed that DEGs were significantly enriched in the upregulated endocytosis and downregulated lysosomal pathways. The coelomocyte viability further decreased 20% in the simultaneous presence of exogenous L-Glu and V. splendidus AJ01, compared to that of V. splendidus AJ01 infection alone. Consequently, a higher mortality of sea cucumber was also observed in the presence of exogenous L-Glu challenged by V. splendidus AJ01. Real time reverse transcriptase PCR showed that L-Glu specifically upregulated the expression of the fliC gene, conding the subunit protein of flagellar filament, with promoted swimming motility activity of V. splendidus. Our result indicated that L-Glu should be kept in a state of equilibrium, and the excess L-Glu in the host-pathogen interface would prompt the virulence of V. splendidus via increasing bacterial motility.

Background: Globally, hot cooked refined rice is consumed in large quantities and is a major contributor to dietary glycaemic load. This study aimed to compare the glycaemic potency of hot and cold stored parboiled rice to widely available medium grain white rice. Method: Twenty-eight healthy volunteers participated in a three treatment experiment where postprandial blood glucose was measured over 120 minutes after consumption of 140g of rice. Three rice samples were freshly cooked medium-grain white rice, freshly cooked parboiled rice, and parboiled rice stored overnight at 4 ºC. All rice was served warm at 65 ºC. Chewing time was recorded. Results: The 24-hours cold-stored and reheated parboiled rice resulted in a 42% and 12% lower blood glucose concentration trajectory than freshly cooked medium-grain white rice and freshly cooked parboiled rice. Chewing time for 10g cold stored parboiled rice was 6 seconds (25%) longer and was considered more palatable, visually appealing and better tasting than freshly cooked medium grain (all P<0.05). Conclusions:. For regular consumers of rice reheating cooked rice after cold storage would lower the dietary glycaemic load and long term may reduce risk for type 2 and gestational diabetes. More trials are needed to identify the significance.

Intelligent systems are increasingly present in various areas of society, gaining special relevance in healthcare environments. In this work, grounded on previous developments proposed by the authors, the evolution and improvement of a novel intelligent system focused on the diagnosis of obstructive sleep apnea (OSA) is addressed. To do this, starting from two packages of information of a heterogeneous nature, and deploying a set of Machine Learning classification algorithms, focused each of them on different levels of the apnea-hypopnea index (AHI), as well as a set of cascaded expert systems, it is possible to obtain a series of risk metric pairs (Statistical Risk, Symbolic Risk) for each AHI level, understood as a warning forecast associated with the early detection of the pathology. The risk indicators of each pair are subsequently aggregated by means of a symbolic inference system, whose knowledge base was determined using the automatic rule generation approach proposed by Wang and Mendel. At the output of each inference system, a risk indicator is obtained for each AHI level, the Apnea Risk, whose interpretation makes it possible to discriminate between patients who could suffer OSA and those who do not, as well as to generate the appropriate recommendations. For the initial tests of the system, the design and development of a specific software artifact was carried out using data from 4,400 patients from the Álvaro Cunqueiro Hospital in Vigo, obtaining when applied to the test set AUC values within the range 0.74–0.88, which invites optimism and points to the benefits expected from the architecture of the proposed intelligent system.

Plants of the genus Monochoria have long been utilized in food, cosmetics, and traditional herbal treatment. Thailand has the highest species diversity of this genus and a new member, Monochoria angustifolia (G. X. Wang) Boonkerd & Tungmunnithum has been recently described. This plant is called “Siam Violet Pearl” as a common name or “ไข่มุกสีม่วงแห่งสยาม” as its vernacular name in the same meaning in Thai language. Despite their importance, few researches on Monochoria species have been conducted. This study, thus, provided the results to fill in this gap by: i) determining flavonoids phytochemical profiles of 25 natural populations of M. angustifolia covering the whole floristic regions in Thailand, and ii) determining antioxidant activity using various antioxidant assays to investigate the probable mechanism. The results revealed that M. angustifolia presented a higher flavonoid content than the outgroup, M. hastata. Our results also revealed that flavonoids might be used to investigate Monochoria evolutionary connections and for botanical authentication. The various antioxidant assays revealed that M. angustifolia extracts preferentially act through a hydrogen atom transfer antioxidant mechanism. Pearson correlation analysis indicated significant correlations emphasizing that the antioxidant capacity is most probably the result of a complex phytochemical combinations rather than of a single molecule. Altogether, these results showed that this new species provide an attractive alternative starting material with phytochemical variety and antioxidant potential for the phytopharmaceutical industry.

The utilization of dual-potential mode of integrated array (IDA) electrodes and other two-electrode systems has revolutionized electrochemical detection by enabling the simultaneous and independent detection of two species, accompanied by the exhibition of unique characteristics. In contrast to conventional dual-potential electrodes, the rotating ring disk electrodes (RRDE), IDA electrodes demonstrate analogous yet vastly improved performance metrics, characterized by remarkable collection efficiency and sensitivity. Notably, due to the distinctive microscale structure of IDA electrode, the special “feedback” effect makes IDA a unique signal amplifier. In recent decades, the research surrounding IDA electrodes has garnered escalating interest due to their attractive attributes. This review centers its focus on the fabrication and applications of IDA electrodes. In the realm of fabrication, two critical breakthroughs are poised for realization: the achievement of reduced dimensions and the diversification of materials. Established fabrication methods for IDA electrodes encompass photolithography, inkjet printing, and direct laser writing, each affording distinct advantages in terms of size and precision in IDA construction. Predominantly employed materials for IDA electrodes include gold, platinum, and carbon, with the selection of fabrication methods guided by considerations such as material properties, desired dimensions, cost-efficiency, and specific application requisites. Within the domain of applications, IDA electrodes, capitalizing on their distinctive attributes, have found utility in diverse fields. This review summarizes the applications of IDA electrodes based on their fundamental working principles, encompassing redox cycling, resistance modulation, capacitance variations, and more. The potential for further development of this specialized tool to exhibit enhanced properties holds substantial promise.

Dacomitinib is an irreversible epidermal growth factor receptor (EGFR) tyrosine kinase inhibitor indicated for the treatment of patients with advanced non-small cell lung cancer (NSCLC) and EGFR-activating mutations. Proton pump inhibitors decreased dacomitinib exposure. This anal-ysis summarizes the effect of H2RA on dacomitinib exposure. A within-patient comparison of steady-state trough concentrations (Ctrough,ss) of dacomitinib and its active metabolite and active moiety with and without concomitant use of H2RA was conducted using a linear mixed effects model with pooled data from 11 clinical studies in patients with NSCLC. An oral absorption PBPK model was constructed and verified using clinical PK data after a single dose of dacomitinib in healthy volunteers to estimate the effect of gastric pH altered by an H2RA on dacomitinib PK. The adjusted geometric mean of dacomitinib Ctrough,ss of dacomitinib parent, metabolite and active moiety following co-administration with H2RA was approximately 86%, 104% and 100% relative to that following dacomitinib 45 mg administration without H2RA (P>0.05). The PBPK modeling showed negligible change in dacomitinib Cmax and AUC over 0-24 hours after H2RA administra-tion, when compared with those administered dacomitinib alone. Co-administration of an H2RA with dacomitinib is not expected to have any clinically relevant effect on dacomitinib exposure.

Non-natural mineralization of CaCO3 with special structures or morphology is generated during the crude oil migration, which is the main scale of alkaline/surfactant/polymer (ASP) flooding in oilfields, adversely affecting the oil recovery and causing environmental pollution. Up to now, the mineralization of superstructural symbiotic aragonites and the role of heavy alkyl-benzene sulfonate (HABS) in directing mineralization are still unclear. In this work, rosette-like, bouquet-like and dumbbell-like aragonite-based superstructure of symbiotic CaCO3 crystals were obtained in a simulated O/W emulsion with HABS, which can help understanding the diversified growth of CaCO3 scaling in oilfield. As a result, HABS stabilized micelles acted as a framework for mineralization, and promoted the accumulation of Ca2+ and CO32-, generating pre-nucleation clusters and partial ion pairs by electrostatic attraction. Following, the sequential nucleation of amorphous CaCO3 interconnected with HABS molecules. Finally, these nanoparticles transformed into micro-meter crystals via dissolution-reprecipitation, forming the superstructures that controlled by a synergistic effect between HABS and kerosene phase. This work may enrich the understanding of CaCO3 mineralization in oilfield, provide theoretical support for the prevention of hard carbonate scaling, and also provide a novel strategy for organic-inorganic composites manufacturing.

Tack is one of the most important factors affecting the operability of prepregs, but it is still very difficult to obtain the change of prepreg tack with time at different temperatures. In this paper, a newly designed T-peel device is used to test the tack decay rate of prepregs at different temperatures. The obtained decay rate deviates less than 8.9% from the manufacturer's data. The maximum deviation of the ratio of tack decay speeds calculated by the Arrhenius equation from the experiments is not higher than -9.7%. It is proved that the present method can obtain the decay rate of tack of prepregs at different temperatures. This method is also applicable to the other two types of prepregs. The article proposes the handling life unit, an operational life measurement unit for prepregs, and establishes that the relationship between tack and remaining shelf life reduces prepreg management costs.

In the process of image feature extraction, noise in the image will greatly affect the accuracy of edge detection. In this paper, the image is filtered to remove noise before edge detection by using the algorithm of wavelet transformation. Different wavelet functions are used to decompose image. Based on the experimental results, the best denoising wavelet function is selected. Canny algorithm is used to detect the edge of the denoised image, and the result of edge detection is evaluated according to the Pratt quality factor. It is proved that wavelet transform can improve the edge detection results.

Accumulating literature demonstrates that omega-3 polyunsaturated fatty acid (N3PUFA) can be incorporated into the phospholipid bilayer of cell membrane in the human body to positively affect the cardiovascular system, including improving epithelial function, decreasing coagulopathy, and attenuating uncontrolled inflammatory responses and oxidative stress. Moreover, it has been proven that the N3PUFA, eicosapentaenoic acid (EPA) and docosahexaenoic acid (DHA), are precursors of some potent endogenous bioactive lipid mediators that mediate some favorable effects attributed to their parent substances. A linear dose-response relationship between increased EPA and DHA intake and reduced thrombotic outcomes have been reported. The excellent safety profile of dietary N3PUFA makes them a prospective adjuvant treatment for people exposed to a higher risk of cardiovascular problems associated with COVID-19. This review presented the potential mechanisms that might contribute to the beneficial effect of N3PUFA and the optimal form and dose applied.

In this study, the effects of various beryllium (Be) addition (Be-free, 0.1, 0.25, 0.50 wt.%) on the microstructure, mechanical properties, and corrosion corrosion of the Al-Mg-Li alloys were systematically investigated. The best performance was obtained in alloy with 0.1 wt.% Be addition. Trace Be addition promotes the grain refinement of the as-cast alloy ingot and contributes positive effects to the recrystallization, bringing improvement of tensile property. Meanwhile, the best anti-corrosion behavior is also presented at 0.1 wt.% Be addition, due to its potential to reduce the width of precipitates free zone (PFZ). As the Be content increase to an excessive level, the comprehensive performance decreases. Therefore, it is strongly recommended that adding trace Be element into Al-Mg-Li alloys has a positive effect on the comprehensive service performance.

As an irreplaceable ecological barrier, the ecological conservation developing area (ECDA) is vital for the integrated construction of urban and rural areas, and optimization and adjustment of industrial structure. Developing green agriculture is the foundation and guarantee for improving the rural ecological environment and meeting the increasing needs of farmers′ income. Issued by the Chinese government, No. 1 Central Document stated the necessity of promoting agricultural green development (AGD) and the related technologies in dealing with ecological pressure and resource shortages, especially for large cities like Beijing. However, few empirical studies have conducted on spatiotemporal variations of AGD in ECDA of large cities. Based on the green agricultural traits of Beijing and the accessible data, we evaluate AGD and analyze its spatial and temporal heterogeneity of Beijing ECDA by constructiing a framework with 13 indicators. The weight coefficients of AGD indicators were calculated by the projection pursuit method, with the district panel data from 2006 to 2016. The results demonstrated that energy consumption is a vital factor of green agriculture production, and agricultural output value per unit of the arable land area is the key to the green agricultural revenue. From 2006 to 2016, the AGD index of ECDA had an increasing trend till 2012, followed by a decreasing tendency. The AGD index of the northern region is higher than the southern of ECDA. The obstacle degree model was used to verify AGD limiting factors. They were poor infrastructure, slow agritourism, low labor productivity, and low resource utilization efficiency that varied by districts in ECDA. Given these findings, our study is conducive to the AGD evaluation at the district (county) level for ECDA of large cities and also provides important policy implications.

During routine bridge maintenance, edge detection allows the partial condition of the bridge to be viewed. However, many edge detection methods often have unsatisfactory performances when dealing with images with complex backgrounds. Moreover, the processing often involves the manual selection of thresholds, which can result in repeated testing and comparisons. To address these problems in this paper, the wavelet transform modulus maxima method is used to detect the target image, and then the threshold value of the image can be determined automatically according to the OTSU method to remove the pseudo-edges. Thus, the real image edges can be detected. The results show that the information entropy and SSIM of the detection results are the highest when compared with the commonly used Canny and Laplace algorithms, which means that the detection quality is optimal. To more fully illustrate the advantages of the algorithms, images with more complex backgrounds were detected and the processing results of the algorithms in this paper are still optimal. In addition, the automatic selection of thresholds saves the operator’s effort and improves the detection efficiency. Thanks to the combined use of the above two methods, detection quality and efficiency are significantly improved, which has a good application in engineering practice.

Historical maps constitute unique sources of retrospective geographic information. Recently, several map archives containing map series covering large spatial and temporal extents have been systematically scanned and made available to the public. The geographic information contained in such data archives allows extending geospatial analysis retrospectively beyond the era of digital cartography. However, given the large data volumes of such archives and the low graphical quality of older map sheets, the processes to extract geographic information need to be automated to the highest degree possible. In order to understand the salient characteristics, data quality variation, and potential challenges in large-scale information extraction tasks, preparatory analytical steps are required to efficiently assess spatio-temporal coverage, approximate map content, and spatial accuracy of such georeferenced map archives across different cartographic scales. Such preparatory steps are often neglected or ignored in the map processing literature but represent highly critical phases that lay the foundation for any subsequent computational analysis and recognition. In this contribution we demonstrate how such preparatory analyses can be conducted using classical analytical and cartographic techniques as well as visual-analytical data mining tools originating from machine learning and data science, exemplified for the United States Geological Survey topographic map and Sanborn fire insurance map archives.

Hydrogen is now recognized as the primary alternative to fossil fuels due to its renewable, safe, high energy density and environmentally friendly properties. Efficient hydrogen production through water splitting has laid the foundation for sustainable energy technologies. However, when hydrogen production is scaled up to industrial levels, operating at high current densities introduces unique challenges. It is necessary to design advanced electrocatalysts for hydrogen evolution reaction (HER) under high current densities. This review will briefly introduce chal-lenges posed by high current densities on electrocatalyst, including catalystic activity, mass dif-fusion and catalyst stability. In an attempt to address these issues, various electrocatalyst design strategies are summarized in detail. In the end, our insights into future challenges for efficient large-scale industrial hydrogen production from water splitting are presented. This review is expected to guide the rational design of efficient high current density water electrolysis electro-catalysts and promote the research progress of sustainable energy.

Microbial contamination is now more common than chemical contamination in Tibet, and water-borne microbes can cause a number of diseases that threaten public health. Thus, in order to clarify the spatiotemporal distribution of bacteria in small watersheds for which there is no data in Tibet, we set up four sampling points along an upstream-downstream transect of the Xincang River Basin. We collected 239 water samples in 2014 and 2015, and evaluated their total constituent numbers of bacteria (TB) and coliforms (TC). The results of this study show that the microbial contamination of the Xincang River Basin is mild-to-moderate in terms of TB and TC contents, and that these concentrations vary significantly in different seasons. Results show that in summer TB and TC concentrations in the downstream section of this river were highest and that microbial contamination was most serious. Data also demonstrate that precipitation is the most important factor underlying increases in TB and TC concentrations during the summer months; both these variables are significantly correlated with precipitation, while animal husbandry and domestic sewage are the main sources of microbial contamination overall. The results of this study are likely to reflect the basic characteristics of small watersheds for which there is no data to some extent, and are thus of significant practical importance for protecting their ecological environments and promoting sustainable development.

The general circuit topology and principles of low-noise high-voltage power supply are investigated to meet the requirements of the high-voltage bias application in air kerma meters. Two topologies, flyback converter and Royer converter are simulated using SPICE simulation program. The simulation results indicate that the circuit structure of the Royer converter is more complex, but it obtains lower output high voltage noise. While we develop an adjustable high-voltage power supply according to the circuit structure of the Royer converter, and tested it to ensure the design requirements for continuously adjustable output high-voltage linearity. The test results show that the linear adjustment rate is not more than ±0.0025%, the load regulation rate is less than ±0.1%, and the output ripple noise voltage percentage is less than 0.01%. These tested performance make it more suitable for accurate nuclear measurements.

With the development of deep learning, several Graph Neural Networks (GNN)-based approaches have been utilized for text classification. However, GNNs encounter challenges in capturing contextual text information within a document sequence. To address this, a novel text classification model RB-GAT is proposed by combining RoBERTa-BiGRU embedding and a multi-head Graph ATtention Network (GAT). First, the pre-trained RoBERTa model is exploited to learn word and text embeddings in different contexts. Second, the Bidirectional Gated Recurrent Unit (BiGRU) is employed to capture long-term dependencies and bidirectional sentence information from the text context. Next, the multi-head graph attention network is applied to analyze this information, which serves as a node feature for the document. Finally, the classification results are generated through a Softmax layer. Experimental results on three benchmark datasets demonstrate that our method can achieve an accuracy of 71.48%, 98.45%, and 80.32% on Ohsumed, R8, and MR, which is superior to the existing nine text classification approaches.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

Abstract: Spatially explicit, fine-grained datasets describing historical urban extents are rarely available prior to the era of operational remote sensing. However, such data are necessary to better understand long-term urbanization and land development processes and for the assessment of coupled nature-human systems, e.g., the dynamics of the wildland-urban interface. Herein, we propose a framework that jointly uses remote sensing derived human settlement data (i.e., the Global Human Settlement Layer, GHSL) and scanned, georeferenced historical maps to automatically generate historical urban extents for the early 20th century. By applying unsupervised color segmentation to the historical maps, spatially constrained to the urban extents derived from the GHSL, our approach generates historical settlement extents for seamless integration with the multi-temporal GHSL. We apply our method to study areas in countries across four continents, and evaluate our approach for two U.S. study sites against historical settlement extents derived from the Historical Settlement Data Compilation for the US, HISDAC-US, achieving Area-under-the-Curve values >0.9. Our results are largely in agreement with model-based urban areas from the HYDE database, and demonstrate that the integration of remote sensing derived observations and historical cartographic data sources opens up new, promising avenues for assessing urbanization, and long-term land cover change in countries where historical maps are available.

This paper aims to build up a preference function to evaluate the public benefits of the type of agricultural farming, biodiversity, water provisions, land use type, ecotourism modes, and a monetary attribute (environmental trust fund and willingness to contribute) associated with an ecosystem service and land use program in a forest park. This study used the choice experiments to build a random utility model, analyze the average preference for the above land use attributes based on the conditional logit and used a latent class model to test the resident’s heterogeneous preferences for land use planning in the forest park. We also estimated the welfare derived from various land use programs. The empirical result had shown that: (1) increasing organic farming area, maintaining the status quo of species biodiversity, increasing the surface water provision, increasing the area of custom flora, increasing the wetland area, and setting up an integrated framework for ecotourism increase the public’s preference for the land use program; (2) we found that farmer and non-farmer haven’t the same land use preferences; (3) the ecotourism development program incorporating biodiversity, organic farming, ethnobotany, and wetland area with integrated ecotourism are more preferred than other land use program scenarios.

Meat serves as a vital component of the human diet, offering a rich source of protein and essential trace elements. China stands as both a significant producer and consumer of meat on a global scale, leading the world in terms of total meat production and consumption. As the standard of living within the country continues to rise, there is a growing emphasis on the nutritional value and safety of meat consumption. The tenderness of meat is a critical factor influencing its overall quality. Traditionally, tenderness has been assessed through shear force testing, a method that is inherently destructive, inefficient, and results in considerable sample wastage. In light of these drawbacks, non-destructive testing techniques have emerged as a preferred alternative, promising greater accuracy, efficiency, and convenience without compromising the integrity of the samples. This paper delves into the application of five advanced non-destructive testing technologies in the realm of meat tenderness assessment. These include near-infrared spectroscopy, hyperspectral imaging, Raman spectroscopy, airflow optical fusion detection, and nuclear magnetic resonance detection. Each technology is scrutinized for its respective strengths and limitations, providing a comprehensive overview of their current utility and potential for future development. Moreover, the integration of these techniques with the latest advancements in artificial intelligence (AI) technology is explored. The fusion of AI with non-destructive testing offers a promising avenue for the development of more sophisticated, rapid, and intelligent systems for meat tenderness evaluation. This integration is anticipated to significantly enhance the efficiency and accuracy of quality assessment in the meat industry, ensuring a higher standard of safety and nutritional value for consumers. The paper concludes with a set of technical recommendations aimed at guiding the future direction of non-destructive, AI-enhanced meat tenderness detection, thereby contributing to the ongoing improvement of the meat industry in China and beyond.

The use of chimeric antigen receptor (CAR) in natural killer (NK) cells for cancer therapy is gaining momentum, marking a significant shift in cancer treatment. This review aims to explore the potential of CAR-NK cell therapy in cancer immunotherapy, providing a fresh perspective. It discusses the innovative approaches in CAR-NK cell design and engineering, particularly targeting refractory or recurrent cancers. By comparing CAR-NK cells with traditional therapies, the review highlights their unique ability to tackle tumor heterogeneity and immune system suppression. Additionally, it explains how novel cytokines and receptors can enhance CAR-NK cell efficacy, specificity, and functionality. The review underscores the advantages of CAR-NK cells, including reduced toxicity, lower cost, and broader accessibility compared to CAR-T cells, along with their potential in treating both blood cancers and solid tumors.

A large amount of steel slag (SS) and CO2 are generated in the steelmaking process. The indirect CO2 capture using SS is a promising way for co-treatment of the wastes. Ammonium salt solution is widely used to extract Ca2+ from the SS since it is recyclable. Several works have focus on improving the carbonation rate by adjusting various parameters (e.g., temperature and pH). However, there is little detail information about the associating behaviors and interaction strength between the various ions in the ammonia solution during the carbonation process. In this work, the Ca2+–CO32-–NH4+–Cl-–H2O system was established by using Material studio software. The effects of temperature and concentration of CO32- on CaCO3 growth were explored at the atomic scale by calculating the binding energy, mean square displacement, and diffusion coefficient between particles. Furthermore, the microstructure, bonding characteristics, and occurrence behavior of each particle were studied though molecular dynamics simulation methods. The results showed that with the increase of temperature (20–80 ℃), the binding ability and diffusion coefficients of Ca2+ and CO32- increase in the system, which is beneficial to the formation of CaCO3 clusters. With the increase of the concentration of CO32- (15–25 vol.%), the binding ability and diffusion coefficient of Ca2+ and CO32- in the system are enhanced, which is beneficial to the formation of CaCO3 clusters.

In order to make full use of the complementarity of existing navigation systems to improve the navigation and positioning accuracy, this paper investigates the visual/INS integrated navigation system based on the factor graph optimization (FGO) algorithm. In the traditional visual/INS integrated navigation system, there is often the problem of image blurring due to the rapid change of light and shadow captured by the vision sensor and the attitude change of the carrier, which leads to the decrease of the positioning accuracy of the combined navigation system. Therefore, this paper firstly introduces Retinex algorithm and BID algorithm to carry out the design of image de-blurring method; then implements the visual/INS integrated navigation algorithm based on the factor graph optimization method; finally, the experimental scheme is designed, comparative experiments are carried out, and the researched method is verified by using the public dataset. The experimental results show that the combined navigation algorithm realized in this paper has high accuracy, and its positioning accuracy is improved by 40% compared with visual positioning.

Multimodal remote sensing data classification can enhance the model’s ability to distinguish land features through multimodal data fusion. In this context, how to help models understand the relationship between multimodal data and target tasks is the focus of researchers. Inspired by human feedback learning mechanisms, causal reasoning mechanisms, and knowledge induction mechanisms, this paper integrates causal learning, reinforcement learning, and meta learning into a unified remote sensing data classification framework and proposed the causal meta-reinforcement learning (CMRL). First, based on feedback learning mechanisms, we have overcome the limitations of traditional implicit optimization of fusion features and customized a reinforcement learning environment for multimodal remote sensing data classification tasks. Through feedback interactive learning between agents and the environment, we help them understand the complex relationships between multimodal data and labels, thereby achieving full mining of multimodal complementary information. Second, based on the causal inference mechanism we designed causal distribution prediction action, classification reward, and causal intervention reward, capturing pure causal factors in multimodal data and cutting off false statistical associations between non-causal factors and class labels. Finally, based on the knowledge induction mechanism, we designed a bi-layer optimization mechanism based on meta-learning. By constructing a meta training task and meta validation task simulation model in the generalization scenario of unseen data, we helped the model induce cross-task shared knowledge, thereby improving its generalization ability for unseen multimodal data. The experimental results on multiple sets of multimodal datasets show that the proposed method achieved state-of-the-art performance in multimodal remote sensing data classification tasks.

Silicon carbide particle-reinforced aluminum matrix (SiCp/Al) composites are significant lightweight metal matrix composites extensively utilized in precision instruments and aerospace sectors. Nevertheless, the inclusion of rigid SiC particles exacerbates tool wear in mechanical machining, resulting in a decline in the quality of surface finish. This work undertakes a comprehensive investigation into the problem of tool wear in SiCp/Al composite materials throughout the machining process. Initially, a comprehensive investigation was conducted to analyze the effects of cutting velocity vc, feed per tooth fz, milling depth ap, and milling width ae on tool wear during high-speed milling under SCCO2-MQL (Supercritical Carbon Dioxide Minimum Quantity Lubrication) ultrasonic vibration conditions. Furthermore, a prediction model for tool wear was developed by employing the orthogonal test method and multiple linear regression. The model's relevance and accuracy were confirmed using F-tests and t-tests. Ultimately, through the utilization of a genetic algorithm, the milling parameters were optimized, resulting in the identification of the most optimal combination of parameters. Empirical findings suggest that the careful selection of milling parameters can significantly mitigate tool wear, extend the lifespan of the tool, and enhance the quality of the surface. This work serves as a significant point of reference for the processing of SiCp/Al composite materials.

Channel bends are one of the most important characteristic features of natural streams. These bends often create the conditions for a hyporheic zone, which has been recognized as a critical component of stream ecosystems. The streambed vertical hydraulic conductivity (K_v), vertical hydraulic gradient (VHG) and Darcian flux (DF) in the hyporheic zone were estimated at 61 locations along a channel bend of the Beiluo River during July 2015 and January 2016. All the streambed attributes showed great spatial variability along the channel bend. Both upward fluxes and downward fluxes occurred during the two test periods, most of studied stream sections were controlled by downwelling, indicating stream water discharge into the subsurface. The average downward flux was higher at the downstream side than at the upstream side of the channel bend, especially in July 2015. The distribution of streambed sediment grain size has a significant influence on the variability of K_v; high percentages of silt and clay sediments generally lead to low K_v values. Higher K_v at the depositional left bank at the upstream site shifted toward the erosional right bank at the downstream site, with K_v values positively correlated with the water depth. This study suggested that the variabilities of K_v and VHG were influenced by the stream geomorphology and that the distribution of K_v was inversely related, to a certain extent, to the distribution of VHG across the channel bend. K_v and VHG were found to have opposite effects on the DF, and the close relationship between K_v and DF indicated that the water fluxes were mainly controlled by K_v.

In modern warfare, the diversified tasks can sometimes be challenging to fulfill with a single projectile, necessitating the incorporation of cooperation constraints in trajectory planning. Limited by the stringent requirements of the launch platform and lower costs, the maneuverability and ability to adjust the flight time range of projectiles are weak. Therefore, the rationality of performance indicators and flight time coordination strategies is especially critical. To fully exploit the control capabilities of projectiles, a battlefield area segmentation method is proposed, differentiated performance indicators and a cooperative trajectory planning model that considers the entire range of projectiles are established. Considering the limitations of existing flight time coordination strategies in applications, targeted improvements have been made in different cooperation scenarios, and a bi-level adaptive cooperation strategy(BACS) with both optimality and flexibility is proposed. To rapidly determine feasible conditions, a simple and universal method for obtaining the capability ranges of cooperation is introduced. The multi-phase optimal control problems are transformed into nonlinear programming problems using the Radau pseudo-spectral method, and simulation results show that the proposed methods are capable of handling trajectory planning tasks in different cooperation scenarios. The improved strategies effectively enhance the planning success rate under relatively harsh conditions and BACS demonstrates good compatibility with the problems studied.

Due to constraints in launch platform and cost, the maneuverability of gliding-guided projectiles is limited, necessitating a rational design of their trajectory schemes. To reduce the sensitivity of trajectory schemes to uncertainties while ensuring compatibility between flight schemes and guidance control systems, and fully exploiting the control capability of the projectile, a closed-loop robust trajectory planning method is proposed. Models of major uncertain factors and states deviation at the control-start point are established. Based on the NIPCE method, the stochastic dynamic model is transformed into a high-dimensional deterministic model with PCE coefficients as state variables, and the uncertainty propagation law is obtained. A PID algorithm is employed to design a tracking guidance law based on position error feedback, and open-loop and closed-loop robust trajectory planning models are established accordingly. The optimal control problem is solved by transforming it into a nonlinear programming problem using the direct shooting method. Simulation results indicate that the NIPCE method can significantly improve the computational efficiency of uncertainty propagation while ensuring accuracy. Open-loop robust planning can effectively mitigate the sensitivity of gliding trajectories to uncertainties but cannot completely eliminate terminal dispersion. Closed-loop robust planning effectively improves control effort consumption on the basis of open-loop planning.

Hyperspectral images (HSI) contain abundant spectral information. Efficient extraction and utilization of this information for image classification remain prominent research topics. Previously, hyperspectral classification techniques primarily relied on statistical attributes and mathematical models of spectral data. Deep learning classification techniques have recently been extensively utilized for hyperspectral data classification, yielding promising outcomes. This study proposes a deep learning approach that uses polarization feature maps for classification. Initially, the polar coordinate transformation method is employed to convert the spectral information of all pixels in the image into spectral feature maps. Subsequently, the proposed Deep Context Feature Fusion Network (DCFF-NET) is utilized to classify these feature maps. The model is validated using three open-source hyperspectral datasets: Indian Pines, Pavia University, and Salinas. The experimental results indicated that DCFF-NET achieves excellent classification performance. Experimental results on three public HSI datasets demonstrate that the proposed method accurately recognizes different objects with an overall accuracy (OA) of 86.68%, 94.73%, and 95.14% based on the pixel method, and 98.15%, 99.86%, and 99.98% based on the pixel-patch method.

This study investigates cloud cavitation suppression around a model scale NACA66 hydrofoil using active water injection and explores the effect of multiple injection parameters. Numerical simulations and a mixed-level orthogonal test method are employed to systematically analyze the impact of jet angle αjet, jet location Ljet, and jet velocity Ujet on cavitation suppression efficiency and hydrofoil energy performance. The study reveals that jet location has the greatest influence on cavitation suppression, while jet angle has the greatest influence on hydrofoil energy performance. The optimal parameter combination (Ljet = 0.30C, αjet = +60 degrees, Ujet = 3.25 m/s) effectively balances energy performance and cavitation suppression, reducing cavitation volume by 49.34% and improving lift-drag ratio by 8.55%. The study found that the jet's introduction not only enhances vapor condensation and reduces the intensity of the vapor-liquid exchange process but also disrupts the internal structure of cavitation clouds and elevates pressure on the hydrofoil suction surface, thereby effectively suppressing cavitation. Further analysis shows that positive-going horizontal jet components enhance the lift-drag ratio, while negative-going components have a detrimental effect. Jet arrangements near the trailing edge negatively impact both cavitation suppression and energy performance. These findings provide valuable reference for selecting optimal injection parameters to achieve a balance between cavitation suppression and energy performance in hydrodynamic systems.

The knowledge of protein function is essential for the study of biological processes, the understanding of disease mechanism and the exploration of novel therapeutic target. Apart from experimental methods, a number of in-silico approaches have been developed and extensively used for protein function prediction. Among these approaches, BLAST predicts functions based on protein sequence similarity, and machine learning predicts functional families from protein sequences irrespective of their similarity, which complements BLAST and other methods in predicting diverse classes of proteins including distantly related proteins and homologous proteins of different functions. However, their identification accuracies and the false discovery rate have not yet been assessed so far, which greatly limits the usage of these prediction algorithms. Herein, a comprehensive comparison of the performances among four popular functional prediction algorithms (BLAST, SVM, PNN and KNN) was conducted. In particular, the performance of these algorithms were systematically assessed by four metrics (sensitivity, specificity, accuracy and Matthews correlation coefficient) based on the independent test datasets generated from 93 protein families defined by UniProtKB Keywords. Moreover, the false discovery rates of these algorithms were evaluated by scanning the genomes of four representative model species (homo sapiens, arabidopsis thaliana, saccharomyces cerevisiae and mycobacterium tuberculosis). As a result, the substantially higher sensitivity and stability of BLAST and SVM were observed compared with that of PNN and KNN. But the machine learning algorithms (PNN, KNN and SVM) were found capable of significantly reducing the false discovery rate (SVM < PNN ≈ KNN). In summary, this study comprehensively assessed the performance of four popular algorithms applied to protein function prediction, which could facilitate the selection of the most appropriate method in the related biomedical research.

To achieve n-type doping in diamond, extensive investigations employing first principles have been conducted on various models of phosphorus doping and boron-phosphorus co-doping. The primary focus of this study is to comprehensively analyze the formation energy, band structure, density of states, and ionization energy of these structures. It is observed that within a diamond structure solely composed of phosphorus atoms, the formation energy of an individual carbon atom is excessively high. However, the substitution of two carbon atoms leads to the conversion of diamond into a p-type semiconductor. Upon examining the P-B co-doping structure, it is revealed that the doped impurities exhibit a tendency to form more stable cluster configurations. As the separation between the freely doped atoms and the cluster impurity structure increases, the overall stability of the structure diminishes, consequently resulting in an elevation of the ionization energy. Analysis of the electronic density of states demonstrates that the electron orbit of the B atom makes negligible contributions to the impurity levels during P-B doping.

Ambrosia trifida is a kind of malignant invasive plant, which has very high reproductive and en-vironmental adaptability. Through strong resource acquisition ability and allelopathy, it could inhibit the growth and reproduction of surrounding plants, destroy the stability of an invasive ecosystem. It is very important to predict the change of suitable distribution area of Ambrosia trifida with climate change before implementing scientific control measures. Based on 106 Ambrosia trifida distribution data and 14 environmental data, the optimal parameter combination (RM = 0.1, FC = LQ) was obtained by using the MaxEnt model optimized by Kuenm package, the potential suit-able areas of Ambrosia trifida in Northeast China under three different climate scenarios (RCP2.6, RCP4.5, RCP8.5) with different emission intensities in the future (2050,2070) were predicted. The changes of Ambrosia trifida suitable area in Northeast China under three climate scenarios were compared, and the relationship between the change of suitable area and emission intensity was analyzed. In general, the suitable area of Ambrosia trifida in Northeast China will expand gradually in the future, and the area of its highly suitable area will also increase with the increasing emission intensity, which is unfavorable to the control of Ambrosia trifida.

The greatly diversified flowering plants (angiosperms) are the dominating and defining group in the current earth ecosystem. However, from which group by what way the flowers, especially their gynoecia (key characteristics of angiosperms), are derived have been the questions in botany unanswered over centuries. Such an embarrassing situation can be attributed to the lack of plants with partially enclosed ovules, which are supposed to be a post between gymnosperms and angi-osperms. Here we report a fossil plant that has an apparent coniferous vegetative and reproduc-tive morphologies but has a single seed partially wrapped by the subtending bract. Such a mor-phology suggests that the carpels in angiosperms may be equivalent to bracts enclosing their axil-lary seed(s). Such a non-traditional interpretation of the homology of angiosperm carpels is com-patible with various new progresses made in botany and is in line with Tomlinson’s recent hy-pothesis. Together with other fossil evidence reported recently, it appears that gynoecia in angio-sperms are derived in multiple ways.

A portable laser photoacoustic sensor based on a Field-Programmable Gate Array (FPGA) is reported for methane detection. A tunable DFB diode laser in the 1654 nm wavelength range is used as an excitation source. The photoacoustic signal processing was implemented by a FPGA device. A small resonant photoacoustic cell is designed. The minimum detection limit (1σ) of 10 ppm for methane (CH₄) is demonstrated.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

The SK model proposed by Sherrington and Kirkpatrick is an important mean field model for spin glasses. The dependence structure of Hamiltonians of the SK model is considered in this paper. We have investigated the covariance matrix of Hamiltonians of the SK model, and establish a relationship between the rank of the corresponding covariance matrix and the dimension of the space spanned by the Hamiltonians. Finally, we also give an upper bound for the rank of the covariance matrix, which might be the best.

To enhance the safety of power grid operations, this study proposes a high-precision short-term photovoltaic power prediction method that integrates information from surrounding pho-tovoltaic stations and the Conv-LSTM-ATT model. In the deep learning prediction model, not only is numerical weather prediction (NWP) data from the target photovoltaic station used as input features, but also highly correlated features from nearby photovoltaic stations are incor-porated. The research begins by analyzing the correlation between irradiance and power se-quences, along with distance factors, to calculate a composite similarity index between the target and other regional photovoltaic stations. Stations with high similarity indices are then selected as data sources. Subsequently, Bayesian optimization techniques are employed to find the optimal data fusion ratios. Ultimately, using the selected data, power prediction mod-eling is conducted via the Conv-LSTM-ATT deep neural network. Experimental results con-firm the superiority of the proposed model, which demonstrates higher predictive accuracy compared to three other classical models. The data fusion strategy determined by Bayesian optimization significantly enhances prediction accuracy, reducing the root mean square error (RMSE) of the test set by 20.04%, 28.24%, and 30.94% for three weather types, respectively.

Concrete is more stable than filler as a false roof in a downward approach type infill quarry, but the mechanical model of a concrete false roof is not clear. As a result, there has been limited application. Therefore, it is necessary to establish the mechanical model of a concrete artificial false roof to enhance the stability of the downward approach infill quarry. This paper combines theoretical analysis, model derivation, finite element analysis and field application methods. Firstly, the basic assumptions of thin plate theory and elasticity mechanics are used as the premise to establish the differential equations of the deflection curve of the concrete thin plate false roof. Then, the three types of bending moment generation of the concrete thin plate false roof are explored. Secondly, the relationship between the location of dangerous surface and dangerous point in hard-supported weak-slab structure and soft-supported weak-slab structure is analyzed, and the type of uniform load and calculation model of concrete thin-slab false roof are improved. Finally, according to the established mechanical model of thin slab false roof, finite element analysis and field application were carried out. The results show that there are three types of deflection curve differential equations in the concrete thin slab false roof perpendicular to the strike, and three extreme points exist in the middle section of the thin slab and on both sides of the surrounding rock. The hazardous surface of the hard-supported weak-slab structure is present at the intersection of the encircling rock and the thin-slab fake ceiling, with the perilous point situated on the top of this surface. The hazardous surface of the soft-supported weak-slab structure can be found in the centre section of the thin-slab fake ceiling, with the perilous point being located at the bottom of this surface. Moreover, the damage mode for both structures is that of maximum tensile stress damage. Upon conducting a finite element analysis, the results indicate that the concrete's maximum tensile stress is significantly high.

Superior fiber quality is one of the most important objectives in cotton breeding. To detect the genetic basis underlying fiber quality, an F2 population containing 413 plants was constructed by crossing Jifeng 914 and Jifeng 173, both of which have superior fiber quality, with Jifeng 173 being better. Five fiber quality traits were investigated in the F2, F2:3, F2:4, and F2:5 populations. Quantitative trait loci (QTL) mapping was conducted based on a high-density genetic map containing 11,488 single nucleotide polymorphisms (SNPs) and spanning 4,202.12 cM in length. Transgressive segregation patterns and complex correlations in the five tested traits were observed. A total of 108 QTLs were found, including 27 for fiber length (FL), 16 for fiber strength (FS), 24 for micronaire (MC), 17 for fiber uniformity (FU), and 24 for fiber elongation rate (FE). Chromosome A7 contained 12 QTL, ranking the first. No QTL was found on chromosome D1 and D11. Each QTL contributed 1.98%–21.45% to the phenotypic variation (PV), including 13 major effect QTLs that contributed more than 10% toward PV. Two QTLs could be repeatedly detected in three populations, including qFL-D3-2 in F2, F2:4, and F2:5 with 9.18%–21.45% of PV, qFS-A11-1 in F2:3, F2:4 and F2:5 with 6.05%–10.41% of PV. Another seven stable QTLs could be detected in two populations, including four major effect QTLs: qFL-A12-3, qFS-D10-2, qMC-D6-2, and qMC-D8-1. Fourteen QTL-overlapping regions were found, which might explain the complex correlations among the five phenotypic traits. Four regions on chromosome A11, D3, D6, and D10 covered by both stable and major effect QTLs are promising for further fine mapping. The genomic regions of the two QTLs detected in three populations and the four major effect QTLs contain 810 genes. Gene functional analysis revealed that the annotated genes are mainly involved in protein binding and metabolic pathways. Fifteen candidate genes in the qFL-D3-2 region are highly expressed in fiber or ovules during fiber initiation, elongation, secondary cell wall thickening, or maturation stages. qRT-PCR revealed that Ghir_D03G005440.1 and Ghir_D03G011310.1 may play a role in promoting fiber initiation, Ghir_D03G006470.1 may be beneficial for promoting fiber elongation. This study provides more information for revealing the molecular genetic basis underlying cotton fiber quality.

Wear-resistant steel/carbon steel composite plate not only has the double performance advantage of high strength and wear-resistance, but also can reduce energy consumption and production cost. Based on 50% reduction rate, the wear resistance of BTW1/Q345 composite was studied at different annealing temperatures, and the dry friction and wear tests of BTW1/Q345 composite at different annealing temperatures were carried out by using RETC MFT-5000. The macro-micro morphology and wear mechanism of wear marks at different annealing temperatures were analyzed by using white light interference three-dimensional surface profiler, Scanning electron microscope scanning electron microscope (SEM) and backscatter electron diffraction (EBSD) . The results show that with the increase of annealing temperature, the grain size near the scratch of BTW1 in the wear-resistant layer of the composite plate is refined, and the wear-resistant property is higher than that of the original sample.When the annealing temperature is 860℃,the wear resistance is the best.

In GNSS/IMU integrated navigation systems, factors such as satellite occlusion and non-line-of-sight conditions can lead to degradation of satellite positioning results, Subsequently affecting the overall accuracy of the integrated navigation system. To address this issue and ef-fectively utilize historical pseudorange information from satellites, this paper proposes a graph optimization-based GNSS/IMU model with virtual constraints. These virtual constraints are con-structed using satellite ‘s position from previous time step, the rate of change of pseudoranges, and ephemeris data. This virtual constraint can serve as an alternative solution for individual satellites in case of signal anomalies, ensuring the integrity and continuity of the graph optimi-zation model. Additionally, this paper conducts an analysis of the graph optimization model constructed using these virtual constraints, comparing it with traditional integrated navigation graph optimization model, and analyzes and reconstructs the marginalization process based on these virtual constraints. The experimental results, compared with tightly coupled Kalman fil-tering and the original graph optimization method on a set of real-world data, demonstrate that the introduction of virtual pseudoranges maintains high positioning accuracy. The RMSE error between it and the original graph optimization remains within 5%, affirming the high feasibility of this approach.

The nuclear factor-ĸB (NF-ĸB) transcriptional system is a major effector pathway involved in inflammatory responses. Previous studies found that a Gardenia decoction (GD) inhibited the expression of NF-κB in a lipopolysaccharide (LPS)-stimulated mouse intestinal injury model. Herein, we hypothesized that geniposide (GE), a component of Gardenia jasminoides Ellis, also exerts anti-inflammatory effects and inhibits NF-ĸB activity in LPS-induced intestinal epithelial cells (IEC-6). IEC-6 cells were stimulated with LPS, following which the effects of GE on NF-ĸB signaling in the IEC-6 cells were examined by western blotting to detect IĸB phosphorylation/degradation. The expression of NF-κB was determined by immunofluorescence assay (IFA). Enzyme-linked immunosorbent assay (ELISA) was used to detect the inhibitory effect of GE on the release of tumor necrosis factor-α (TNF-α), interleukin-6 (IL-6) and interleukin-1β (IL-1β) activated by LPS in IEC-6 cells. In addition, the migration ability of IEC-6 cells was observed by the scratch method. These results showed that GE dose-dependently downregulated levels of the proinflammatory cytokines TNF-α, IL-6 and IL-1β that had been upregulated by LPS and suppressed the phosphorylation of IĸB and NF-ĸB induced by LPS. Our findings indicated that GE could reduce LPS-induced NF-ĸB signaling and proinflammatory expression in IEC-6 cells and significantly enhance the migration of IEC-6 cells. Moreover, GE inhibited the expression of NF-κB, nuclear transfer, and transcriptional activity in IEC-6 cells. GE could block the synthesis of inflammatory factors of IEC-6 cells by inhibiting activation of the IĸB/NF-κB signaling pathway induced by LPS.

This survey of research literature is an overview of the current state of science addressing DSM-5 diagnostic criteria as it relates to identifying Autism Spectrum Disorder (ASD) in young children. Selected sources are of high quality and have been published since 2020 in peer-reviewed journals relevant to children’s health. The narrative is organized from the earliest to the most recent publications and is divided into sections around categories and themes that highlight the main arguments, findings, and controversies identified by researchers. There are indications in the literature that while ASD can be identified and differentiated from other developmental disorders in young children, doing so requires that clinicians who have relied on the DSM-5 should also use multiple measures, including other formalized screening tools as assessments that gather observational input from parents and caregivers, as well as findings from physical examinations, laboratory investigations, and magnetic resonance imagining (MRI). This high level of corroboration points to an emerging diagnosis paradigm through which transdiagnostic approaches to early diagnosis and intervention may exist.

Currently, in some domestic and foreign mines, the backfill drilling pipeline experience a rupture phenomenon even when the wear degree is low. This results in a delay in production due to the filling becoming 'sick'. This paper presents, for the first time, the damage mechanism from a mechanical perspective and re-derives the anti-extrusion strength model of the backfill drilling pipeline. We investigate the influence of law on the anti-extrusion strength of pipelines from the perspective of stratum and cement ring. We then verify the theoretical and simulation results through engineering examples. The results demonstrate that the Mises stress criterion is a suitable modification principle for the anti-extrusion strength model of the backfill drilling pipeline. The anti-extrusion strength of the pipeline is related to the elastic modulus and Poisson's ratio of the stratum, and the thickness of the cement ring. It is negatively affected by the depth of the stratum. For hard strata, a cement ring with a smaller elastic modulus is suitable, while for soft stratum, a cement ring with a larger elastic modulus is recommended. When the missing angle of the cement ring is less than 60°, the stress concentration factor increases up to 2.2. The stress unloading capacity of the cement ring ranges from 32.7% to 37.8%, and optimal performance of the cement ring is achieved when it has high strength and low rigidity. The backfill filling pipeline of a copper mine abroad was destroyed due to external extrusion force exceeding its anti-extrusion strength value. The modified pipeline anti-extrusion strength model is 18.2% higher than the casing API strength value. This finding can inform the design of the backfill filling pipeline for China's kilometer-deep wells in the future.

To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

Driving factors of smart city construction are exploratively studied by grounded theory method based on text sources from journal papers in SCI and CSSCI databases. Initial scale of driving factors about smart city construction is obtained on the basis of above analyses. This paper modifies measuring items of the initial scale with a small sample pretest and reliability test, then forms final items by exploratory factor analysis. According to the above scale, questionnaires are designed to obtain empirical data, and confirmatory factor analysis is used to verify further validity and reliability of the scale. The results show that driving factors of smart city construction include three main dimensions: problem-oriented factors, business- or technology-driven factors and endogenous development requirements.

It is difficult to effectively operate a dual-arm robot using only the information written in a cooking recipe. To cope with this problem, this paper proposes a graph based approach on bimanual cooking motion planning from a cooking recipe. In our approach, we first decompose the cooking recipe into graph elements. Then, we try to connect the graph elements taking into account the attributes of the input/output nodes. If two graph elements cannot be connected each other, we search for a graph element that can be inserted between them from the database of graph elements. Since the constructed graph includes the whole sequence of the robot’s motions to perform the cooking task, we can generate a task sequence of a dual-arm manipulator simultaneously performing two different tasks by using two arms. Through experimental study, we show that it is possible to generate robot motions from a cooking recipe and perform the cooking motions while simultaneously moving the left and right arms.

The superconductivity of CaC6 as a function of pressure and of abundant Ca isotopes is revisited using DFT calculations on a 2c – double hexagonal superlattice. The introduction of superlattices is motivated by previous synchrotron absorption and Raman spectroscopy results on other superconductors that show evidence of superlattice vibrations at low (THz) frequencies. A 2c superlattice for CaC6 is illustrative of atomic orbital symmetry and periodicity, including bonding and antibonding s-orbital character implied by cosine modulated electronic bands. Inspection of the cosine band reveals that the cosine function has a small (meV) energy difference between bonding and antibonding regions relative to a midpoint non-bonding energy. Fermi surface nesting is apparent in an appropriately folded Fermi surface using a superlattice construct. Nesting relationships identify phonon vectors for conservation of energy and for phase coherency between coupled electrons at opposite sides of the Fermi surface. Detailed analysis of this Fermi surface nesting provides accurate estimates of the superconducting gaps for CaC6 with change in applied pressure. Recognition of superlattices within a rhombohedral or hexagonal representation provides consistent mechanistic insight on superconductivity and electron−phonon coupling in CaC6.

Carbon dioxide (CO2)miscible fracturing huff and puff technology plays a pivotal role in enhancing the recovery rate of crude oil, particularly in reservoirs with challenging physical properties, strong water sensitivity, high injection pressure, and complex water injection dynamics. In this study, the oil-increasing mechanism and huff and puff effect of CO2 miscible fracturing fluid are investigated through a comprehensive experimental approach. Specifically, experiments on PVT gas injection expansion, minimum miscible pressure, and CO2 miscible fracturing huff and puff are conducted on the G fault block reservoir in J Oilfield. The findings demonstrate that injecting CO2 into reservoirs leads to oil volume expansion, viscosity reduction, and saturation pressure increase. Additionally, the inclusion of solubilizers and viscosity reducers further enhances the efficiency of crude oil extraction. Solubilizers not only improve oil recovery but also reduce the minimum miscible pressure required for effective CO2 dispersion. Furthermore, the shut-in time, permeability, and huff and puff method all have considerable impacts on huff and puff recovery rate. This study offers valuable technical insights, supporting the application of CO2 miscible fracturing huff and puff technology to enhance oil recovery in low-permeability reservoirs.

An eight-sided prism sample, obtained from a hot-rolled AZ31 magnesium alloy sheet, was compressed at room temperature along the transverse direction to investigate the influence of local strain on twinning behavior using electron backscatter diffraction (EBSD) measurements. The octagonal surface of the sample was divided into distinct regions based on hardness distribution and metallographic observations. The EBSD maps of different areas show significant variations, suggesting that these areas experienced different local strain conditions. The EBSD measurements provided detailed data from three distinct regions, with the strain state known in two regions and uncertain in the third. The combined analysis of the Schmid factor (SF) and the strain compatibility factor (m') was employed to study twin variant selection. The comparison of twinning behavior in different regions showed that the strain compatibility factor offered a more comprehensive explanation for the observed twinning pattern in the region with local shear strain.

There are rich proper noun derivative semantic relationships in geographic entity vector data. The identification of traditional proper noun derivative semantic relationships usually requires toponym researchers to examine the source of derived toponyms by consulting a large number of toponym documents. This method cannot adapt to the mining of proper noun derivative semantic relationships for large-scale geographical entity. In this regard, this paper proposes a method of identifying the proper noun derivative semantic relationships for geographical entity by combining prompt learning and XGBoost model. This method transforms the extraction problem of proper noun derivative semantic relationships into a binary classification problem by analyzing the characteristics of the derivation relationship of toponyms in the form of toponyms and the spatial and temporal distribution of geography. Firstly, prompt learning and gaussian mixture model are used to extract and cluster the derivation words of toponyms, so as to realize the recognition of derived toponyms collections. Then, enumerate the possible proper noun derivations in the toponym set, and then the XGBoost model is used to identify the semantic relations derived from the proper noun of geographical entities. In the experiment, the recognition method of proper noun derivative semantic relationships based on prompt learning and XGBoost proposed in this paper has achieved good relationship recognition effect in the experiment. This method has certain practical value in the fields of toponym management and toponym translation.

We suppose that a Cooper pair (CP) will experience a damping force exerted by the condensed matter. A Langevin equation of a CP in two dimensional condensed matter is established. Following a method similar to Nelson's stochastic mechanics, generalized Schr\"{o}dinger equation of a CP in condensed matter is derived. If the CPs move with a constant velocity, then the corresponding direct current (DC) electrical conductivity can be calculated. Therefore, a Drude like formula of resistivity of CPs is derived. We suppose that the damping coefficient of CPs in two dimensional cuprate superconductors is a linear function of temperature. Then the resistivity and scattering rate of CPs turn out to be also linear-in-temperature. The origin of linear-in-temperature resistivity and Planckian dissipation in cuprate superconductors may be the linear temperature dependence of the damping coefficient of CPs.

Intense climate change and rapid urbanization have increased the risk of urban flooding, seriously affecting urban economic and social stability. Enhancing the urban flood resilience (UFR) has required a new solution to cope with urban flood disasters. In this study, taking Yingtan city as an example, a system of indicators for evaluating UFR was constructed, with 17 representative indicators, comprising three subsystems: socio-economic, ecological and infrastructural. A hybrid (FAHP-EWM)-TOPSIS model was applied, to develop an index-based measurement to compare and evaluate UFR, and Gray Relational Analysis (GRA) was used to discover the main factors affecting UFR. In addition, the natural discontinuous method was innovatively used to divide the UFR grade interval into levels, and the grade change was evaluated based on the TOPSIS method. The results showed that (1) from 2010 to 2022, the UFR in Yingtan City increased by 80.69%, and the factors affecting UFR are highly correlated with urban infrastructure development. However, the ecological resilience in the subsystem showed a fluctuating downward trend, because of the influence of the surface area of lakes and rivers. (2) The grades of UFR for Yingtan City increased from Level III (2010 and 2016) to Level IV (2022), with local financial expenditures and the age structure of the population being the main factors currently limiting the development of UFR. The study provides a theoretical basis for the construction of an indicator system for assessing the UFR of Yingtan and proposes practical improvement directions for UFR.

Color image binarization plays a pivotal role in image preprocessing work, significantly impacting subsequent tasks, particularly in text recognition. This paper concentrates on Document Image Binarization (DIB), aiming to separate a image into foreground (text) and background (non-text content). Through a thorough analysis of conventional and deep learning-based approaches, we conclude that prevailing DIB methods leverage deep learning technology. Furthermore, we explore the receptive fields pre- and post-network training to underscore the Transformer model's advantages. Subsequently, we introduce a lightweight model based on the U-Net structure, enhanced with the Mobile ViT module to better capture global information features in document images. Given its adeptness at learning both local and global features, our proposed model exhibits superior performance on two standard datasets (DIBCO2012 and DIBCO2017) compared to state-of-the-art methods. Notably, our proposed DIB method presents a straightforward end-to-end model devoid of additional image preprocessing or post-processing. Moreover, its parameter count is less than a quarter of the HIP'23 model, which achives best results on three datasets(DIBCO2012, DIBCO2017 and DIBCO2018). Finally, two sets of ablation experiments were conducted to verify the effectiveness of the proposed binarization model.

The carbonyl iron particles were dispersed in a polychloroprene rubber (CR) matrix under an external magnetic field for practical application as microwave absorption composites film. The film prepared under external magnetic field with a thickness of only 0.54 mm showed least reflection loss of -15.98 dB and the reflection loss value less than -10.0 dB over the frequency range of 11.4~14.8 GHz. In comparison with the microwave absorption properties of calculation by transmission line theory based on the tested relative complex permittivity and permeability and film prepared by general route without external magnetic field, the film made with external magnetic field exhibited more excellent microwave absorption properties, strongly depending on the increment of anisotropy and rearrangement of magnetic particles. The results indicated the composite film made under external magnetic field have excellent microwave absorption properties, which suggest that the composites thin film could be used as a thinner and lighter microwave absorber.

In this work, we propose a generalized partially functional linear regression model with an interaction term between functional predictors. The estimators of the regression coefficient of scalar predictors and regression coefficient functions of functional predictors and their interactions are obtained. The asymptotic property of the estimators is established. Extensive simulation studies illustrate the asymptotic results. Finally, the proposed model was applied to investigate the influence of air qualities, climate factors, medical and social indicators and the interactions on cancer incidence which is a binary response.

The intelligent elderly care model places new demands on the skills of aging caregivers. The identification and development of forward-thinking, high-potential nursing talent is essential for advancing the intelligent elderly care sector. Multi-benchmarking selection and competitive analysis is used to evaluate and identify nursing personnel in the rehabilitation treatment center of a hospital in Hefei City. Using proxy evaluation and democratic evaluation model, three types of benchmarks such as single item benchmark, individual benchmark and group benchmark were identified and selected, and the professional nursing team was constructed based on the evaluation results. Different from the traditional other-directed evaluation, multi-benchmarking selection and competitive analysis is self-directed evaluation, this method is more conducive to the identification of high-potential and digital nursing talents by intelligent elderly service organizations, and facilitates the formation of professional nursing teams with complementary strengths and cross-fertilization, so as to satisfy the diversified and multi-level needs of the elderly for intelligent elderly services.

This literature review paper delves into the synergies between Climate-Smart Agriculture (CSA) and the effective management of food losses. With the escalating challenges posed by climate change and the pressing need to address food security concerns, the intersection of these two critical domains becomes paramount for sustainable agricultural practices. The review explores existing research on the implementation of climate-smart agricultural techniques and their impact on mitigating food losses throughout the agricultural value chain. The paper synthesizes findings related to climate-resilient crop varieties, precision farming, water-use efficiency, and sustainable soil management, highlighting their contributions to reducing post-harvest losses and enhancing overall food security. In addition to summarizing current knowledge, this paper identifies gaps in the literature and proposes avenues for future research. This review serves as a foundation for researchers, policymakers, and practitioners seeking to contribute to the advancement of climate-smart agriculture and the reduction of food losses, paving the way for a more sustainable and resilient global food system.

The association between normal-range triglycerides and diabetes mortality remains unclear. This cohort study aimed to elucidate this relationship by examining 19,010 US adult participants with fasting serum triglycerides below 150 mg/dL. Cox proportional hazards models were employed to estimate mortality hazard ratios (HRs) and 95% confidence intervals (CIs). Participants were followed up for a mean of 15.3 years, during which 342 diabetes deaths were recorded. A 1-natural-log-unit increase in triglycerides was associated with a 57% higher risk of diabetes mortality (adjusted HR, 1.57; 95% CI, 1.04–2.38). Comparable results were obtained when triglycerides were analyzed in quartiles. Receiver operating characteristic curve analysis identified an optimal triglyceride cutoff of 94.5 mg/dL for diabetes mortality; individuals with triglyceride levels above this threshold faced a greater risk of diabetes mortality (adjusted HR, 1.43; 95% CI, 1.12–1.83). Further investigation revealed a positive association between normal triglyceride levels and all-cause mortality, though no association was observed between normal triglycerides and mortality from hypertension or cardiovascular disease. In conclusion, elevated triglycerides within the normal range were associated with an increased risk of diabetes mortality. Individuals with triglyceride levels of 95 mg/dL or higher may require vigilant monitoring for diabetes and its associated complications.

Focused microwave breast hyperthermia (FMBH) employs a phased antenna array to perform beamforming that can focus microwave energy at targeted breast tumors. Selective heating of the tumor endows the hyperthermia treatment with high accuracy and low side effects. The effect of FMBH is highly dependent on the applied phased antenna array. This work investigates the effect of polarizations of antenna elements on the microwave focusing results by simulations. We explore two kinds of antenna arrays with the same number of elements using different digital realistic human breast phantoms. The first array has all the elements’ polarization in the vertical plane of the breast while the second array has half elements’ polarization in the vertical plane and the other half in the transverse plane, i.e., cross polarization. In total 96 sets of different simulations are performed, and the results show that the second array leads to a better focusing effect in dense breasts than the first array. This work is very meaningful for the potential improvement of the antenna array for FMBH, which is of great significance for the future clinical applications of FMBH. The antenna array with cross polarization can also be applied in micro-wave imaging and sensing for biomedical applications.

Extreme climates such as droughts and hot extremes, may result in marked damage to crop yields and threaten regional and global food security. Maize is a major grain crop in Liaoning Province, severely affected by drought and hot events. The objective of this study is to advance an approach to estimate the risk of crop yield reduction under the compound dry-hot events (CDHE) in Liaoning Province. Results show that the ratio of stations experiencing compound dry-hot events during the twelfth leaf and maturity stage tended to increase on the time scale. On a spatial scale, the frequency of compound dry-hot events in central Liaoning Province was relatively low during the whole and various reproductive periods of maize. In addition to the twelfth leaf, western Liaoning Province is prone to compound dry-hot events. The high-risk area for the occurrence of the compound dry-hot events in maize is Chaoyang City, located in the western part of Liaoning Province, and the cities in the low-risk area account for about 64.3% of the total number of cities in Liaoning Province, mainly in the central and northern parts of Liaoning Province. Generally, this study emphasizes focusing on the impacts of compound dry-hot events on agricultural production and provides an index to assess the risk of compound dry-hot events on maize production.

Distributed/semi-distributed models are considered to be sensitive to the spatial resolution of the data input. In this paper, we take a small catchment in high urbanized Yangtze River Delta, Qinhuai catchment as study area, to analyze the impact of spatial resolution of precipitation and the potential evapotranspiration (PET) on the long-term runoff and flood runoff process. The data source includes the TRMM precipitation data, FEWS download PET data, and the interpolated metrological station data. GIS/RS technique was used to collect and pre-process the geographical, precipitation and PET series, which were then served as the input of CREST (Coupled Routing and Excess Storage) model to simulate the runoff process. The results clearly showed that, the CREST model is applicable to the Qinhuai catchment; the spatial resolution of precipitation had strong influence on the modelled runoff results and the metrological precipitation data cannot be substituted by the TRMM data in small catchment; the CREST model was not sensitive to the spatial resolution of the PET data, while the estimation fourmula of the PET data was correlated with the model quality. This paper focused on the small urbanized catchment, suggesting the influential explanatory variables for the model performance, and providing reliable reference for the study in similar area.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

This study establishes a multivariate function model for natural human load carrying walking in some typical scenarios like college equipments and materials relocation for students. For classified materials relocation needs and constraints, we obtain the relationship between walking speed and load weight for single person, as well as the time cost for different round trips. By establishing an integer programming model with the minimum total transportation time cost and quality assurance as the objective function and the requirements of negative weight and speed as the constraints conditions, we reach the optimal item allocation methods considering time cost and shelf life were obtained. We discover that there is an approximate linear relationship between the change in natural walking speed and travel time when the load is small, thus obtaining the time cost of student transportation under different round-trip situations. The Monte Carlo simulation algorithm is used to obtain the optimal allocation scheme that meets the efficiency and quality requirements. The analysis methods and results can be used as guidance for task scheduling optimization for material relocation in educational organizations as well as commercial agencies.

The intestinal microbiota, comprised of bacteria, archaea, and phages, inhabits the gastrointestinal tract of the organism. Male reproductive sterility is currently a prominent topic in medical research. Increasing research suggests that gut microbiota dysbiosis can result in various reproductive health problems. This article specifically investigates the impact of gut microbiota dysbiosis on male reproductive infertility development. Gut microbiota imbalances can disrupt the immune system and immune cell metabolism, affecting testicular growth and sperm production. This dysfunction can compromise the levels of hormones produced and secreted by the endocrine glands, affecting male reproductive health. Furthermore, imbalance of the gut microbiota can disrupt the gut-brain-reproductive axis, resulting in male reproductive infertility. This article will explore how the imbalance of the gut microbiota impacts male reproductive infertility through immune regulation, endocrine regulation, and interactions of the gut-brain-reproductive axis, concluding with recommendations for prevention and treatment.

This study investigates the impact of specimen size on the mechanical properties of wood, specifically focusing on compression strength, elastic modulus, and Poisson's ratio. Compression tests were conducted using three different specimen sizes (20mm×20mm×30mm, 40mm×40mm×60mm, 60mm×90mm×90mm) in the longitudinal, radial, and tangential directions. Mechanical parameters, failure mechanisms, load-displacement curves, and stress-strain relationships were systematically analyzed for each size. The study also evaluated the influence of specimen size on the accuracy of finite element numerical simulations by utilizing the obtained mechanical parameters. The results reveal a significant correlation between compressive strength and specimen size, indicating a decrease in compressive strength with increasing specimen size. Conversely, elastic modulus and Poisson's ratio exhibit less sensitivity to variations in specimen size. Notably, parameters derived from small-sized specimens (20mm×20mm×30mm) exhibited substantial errors, while those obtained from medium-sized (40mm×40mm×60mm) and large-sized specimens (60mm×90mm×90mm) demonstrated greater reliability, providing precise results in finite element numerical simulations.