The nozzle is the key element of the water jet generator for energy conversion. In order to explore the influence of the nozzle diameter on the pressure characteristics of the supercharged pulsed water jet plenum chamber, a supercharged pulsed water jet pressure acquisition system was established, and the Equations of motion and theoretical pressurization ratio equations of the supercharged pulsed water jet generator were established. The pressurization chamber pressure acquisition experiments under different nozzle diameters were carried out. The research results indicate that there is a critical nozzle diameter. When the nozzle diameter is less than the critical diameter, the pressure in the boost chamber is equal to the product of the driving pressure and boost ratio. As the nozzle changes, there is no significant change in the peak pressure and frequency of the boost chamber; When the nozzle diameter is greater than the critical diameter, there is a non-linear relationship between the boost chamber pressure and the driving pressure. As the nozzle diameter gradually increases, the actual boost ratio gradually decreases, and the peak pressure of the boost chamber further decreases. The nozzle diameter can no longer provide a load for the establishment of fluid pressure in the boost chamber. The research results provide a research basis for further controlling the pressure characteristics of the boost pulse water jet.

Dynamic time history analysis is a powerful and effective method to study the seismic response of tunnels, the dynamic time history to analyze the seismic response of the tunnel in the typical subway in this paper. The analysis results show that the overall levelling of the tunnel will not affect the tunnel too much, and the seismic response of the tunnel is mainly related to the relative displacement of the ground around the tunnel. The analysis results show that the internal force of the tunnel and the tunnel inclination have a good linear relationship, and the tunnel inclination can be used to measure the magnitude of the seismic response of the tunnel.

Understanding the subtle signs of carpal instability and other unique injury patterns in the wrist is a critical skill for radiologists. Proper patient management and outcomes are directly dependent on the accurate interpretation of wrist imaging studies. This review will provide a detailed overview of typical imaging features of carpal trauma and instability, management, and complications, using multimodality imaging and original medical illustrations. A detailed overview of the osseous, ligamentous, arterial anatomy of the wrist, arcs of Gilula, and zones of vulnerability will be provided. Carpal fractures, dislocations, special radiographic views, and imaging pearls will be discussed. Instability patterns and the myriad of associate abbreviations (CID, CIND, CIC, CIA, VISI, DISI, SLD, LTD, MCI, SLAC, SNAC) will be clarified. Expected outcomes, potential complications, and management will be reviewed.

The research on the excavation mechanical properties of underpass tunnels has already had certain results, but fewer of them consider the effects of dynamic and static loads on the excavation mechanical properties of underground tunnels at the same time, especially the lack of research cases of double-line highway tunnels with angled underpasses of existing railway tunnels. In this paper, based on the tunnel project of the new double-line Shiqian Highway Tunnel passing under the Hurong Railway at an oblique angle, the mechanical parameters of the rock body in the cross-tunneling area under the influence of static and dynamic load coupling are obtained by using the disturbance quantification coefficients and the Hoek-Brown criterion based on the method of over-advanced geological prediction and the investigation of the surrounding rock on the palisade face, and the engineering-scale finite element model is constructed and the mechanical characteristics of the excavation in the tunnel of the double-lane highway tunnel passing under the existing railroad under the influence of the static and dynamic loads are analyzed. The results show that: the new tunnel rock movement law for the top of the arch sinking, bottom plate bulging, side wall to move outward, the height and width of the arch and bottom plate arch with the tunnel excavation and increase, the side wall rock displacement effect is smaller; left and right lines of the tunnel disturbed area of the rule of change is similar; the existing tunnel bottom plate displacement is more than the top plate and the left and right side walls by the excavation of the time step influence is larger. Typical profile displacement is mainly determined by the distance from the excavation surface; the new tunnel in the four types of calculation conditions of the rock disturbance angle is the same; the existing tunnel roof and side wall Von Mises stress extreme occurs in the tunnel structure, the bottom plate there are pressure relief and pressure-bearing areas; based on the displacement control criteria, the recommended upper and lower step blasting method.

Mobile inspections conducted by intelligent tunnel robots are instrumental in broadening the inspection reach, economizing on inspection expenditures, and augmenting the operational efficiency of inspections. Despite differences from fixed surveillance, mobile-captured traffic videos have complex backgrounds and device conditions that interfere with accurate traffic event identification, warranting more research. This paper proposes an improved algorithm based on YOLOv9 and DeepSORT for intelligent event detection in edge computing mobile device using the intelligent tunnel robot. The enhancements comprise the integration of the Temporal Shift Module to boost temporal feature recognition and the establishment of logical rules for identifying diverse traffic incidents in mobile video imagery. Experimental results show that our fused algorithm achieves a 93.25% accuracy rate, an inprovement of 1.75% over the baseline. The algorithm is also applicable to inspection vehicles, drones, and autonomous vehicles, effectively enhancing the detection of traffic events and improving traffic safety.

Diabetes is a major health concern that the next-generation of on-demand insulin releasing implants may overcome for personalized therapy. Therein, 3D-printed phenylboronic acid-containing subcutaneous implants with on-demand glucose-triggered drug release abilities are produced using high resolution stereolithography technology. To that end, the methacrylation of phenylboronic acid is targeted following a two-step reaction. The resulting photocurable phenylboronic acid derivative is accordingly incorporated within bioinert polyhydroxyethyl methacrylate-based hydrogels at varying loadings. The end result are sub-centimeter scaled 3D-printed bionert implants that can be remotely activated with 1,2-diols and 1,3-diols such as glucose for on-demand drug administration such as insulin. As a proof of concept, varying glucose concentration from hypoglycemia to hyperglycemia levels readily allow the release of pinacol, i.e. a model molecule with similar release properties than insulin, at respectively low and high rates. In addition, the results demonstrated that adjusting the geometry and size of the 3D-printed part is a simple and suitable method for tailoring the release behavior and dosage.

Tunnel fires are generally detected using various sensors, including measuring temperature, CO concentration, and smoke concentration. To address the ambiguity and inconsistency in multi-sensor data, this paper proposes a tunnel fire detection method based on an improved Dempster-Shafer (DS) evidence theory for multi-sensor data fusion. To solve the problem of evidence conflict in DS theory, a two-level multi-sensor data fusion framework is adopted. The first level of fusion involves feature fusion of the same type of sensor data, removing ambiguous data to obtain characteristic data, and calculating the basic probability assignment (BPA) function through the feature interval. The second level fusion derives basic probability numbers from the BPA, calculates the degree of evidence conflict, normalizes to obtain the relative conflict degree, and optimizes the BPA using the trust coefficient. The classical DS evidence theory is then used to integrate and obtain the probability of tunnel fire occurrence. Different heat release rates, tunnel wind speeds, and fire locations are set, forming four fire scenarios. Sensor monitoring data under each simulation condition are extracted and fused using the improved DS evidence theory. The results show that the proposed improved DS evidence theory method detects the probability of fire occurrence in the four scenarios as 67.5%, 71.0%, 82.8%, and 83.5%, respectively, and identifies fire occurrence in approximately 2.4 seconds, an improvement of 64.7% to 70% over traditional methods. This demonstrates the feasibility and superiority of the proposed method, highlighting its significant importance in ensuring personnel safety.

Consideration of the individual bone characteristics of the wrist plays a key role in well-functioning biomedical devices and successful surgical procedures. Although geometric differences and individual bone sizes have been analyzed in the literature, detailed morphologic descriptions and correlations covering the entire wrist reported in a clinical context are lacking. This study aimed to perform a comprehensive and automatic analysis of wrist morphology using the freely available “Open Source Carpal Database” (OSCD). We quantified the dimensions of each of the individual carpal bones and their combination. These dimensions were extracted in n=117 datasets of the wrist of the OSCD in anatomical directions and analyzed using descriptive statics and correlation analysis to investigate morphological characteristics under gender-specific aspects. We found that there exist statistical differences between genders, and we concluded that gender specificity is an important variable affecting the utilization of biomedical device designs and clinical treatment.

Tunnel-interchange connecting sections pose significant safety challenges on mountainous expressways due to their high incidence of accidents. Improving road safety necessitates a comprehensive understanding of driver behavior in such areas. This study explores the influences of road characteristics, signage information volume, and traffic conditions on drivers' car-following and lane-changing behavior in tunnel-interchange diverging areas. Utilizing driving data from 25 subjects of 72 simulated road models, driving performance is assessed using Friedman rank test and multivariate variance analysis. The results highlight the significant influence of both connection distance and signage information load on driving behavior. In tunnel-interchange scenarios, the reduction of velocity increased by 62.61%, and speed variability surged by 61.11%, indicating potential adverse effects on driving stability due to the environmental transitions. Decreased connection distances are associated with reduced lane-changing durations, larger steering angles, and increased failure rates. Furthermore, every two units increase in signage information leads to a 13.16% rise in maximum deceleration and a 5% increase in time headway. Notably, the signage information volume shows a significant interaction with connection distance (F=1.60, P=0.045) for most car-following indicators. Hence, the study recommends a maximum connection distance of 700 m and signage information not exceeding nine units for optimal safety and stability.

By repeated unloading and loading of the excavation dynamic and static loads, repeated train dynamic and static loads of multi-factors, the underpass tunnel, cross tunnel engineering influence area rock layer, the existing tunnel structure of the three constitutes a multifaceted structure, multi-factor interaction system. Existing tunnels into the prediction theory model of the new tunnel excavation process of dynamic and static loads, dynamic and static loads of existing tunnels are mostly analyzed individually, the results of synergistic analysis needs to be improved. Based on the theory of the current layer method, the paper comprehensively considers the stiffness of the existing tunnel, the stiffness of the new tunnel, the excavation method load and the existing tunnel load, coupled with Peck's empirical formula, the theoretical model of deformation prediction for excavation of a two-lane highway tunnel under the tunnel through the existing railroad is proposed, and verified and optimized by numerical calculations and monitoring data, which proves the applicability and reliability of the theoretical model in the similar strata and the project promotion.

The enterprise software sector is experiencing a significant transformation driven by rapid technological progress and evolving business needs. An effective release management process is crucial for the solution providers and customers, as they incorporate the principles of Industry 4.0 and 5.0. With the growing dependence on software solutions and services, ensuring their quality, reliability, and security is highly necessary. The release management process incorporates strategic planning, regression testing, accurate deployment, and continuous monitoring of software updates. However, the rapid advancements in artificial intelligence (AI) and machine learning (ML) create a unique challenge to the release management process. The existing research needs to address the necessary adaptations for Industry 5.0, mainly in product-based software organizations, to the release management process without a change management system. After working with several software solution stakeholders, based on the responses from SaaS project stakeholders, we have presented a revised software release readiness workflow by incorporating a change management module. The preliminary result based on data over a limited period of time indicates that the revised workflow has the potential to improve the management of slippage, particularly by more effectively addressing NFR-related issues, thereby resulting in more predictable and reliable release cycles.

Research shows that in earthquakes the ground response changes in areas where there are underground cavities. Due to the fact that subways and underground tunnels pass from beneath buildings in urban areas, these changes in ground response have a direct impact on the seismic behavior of structures. In this study, first by model validity and reliability of the results, steel structures modeling was conducted and steel structure behavior was evaluated due to Tunnel-Soil-Structure seismic interaction. Parameters studied are number of stories, soil type, tunnel depth, horizontal tunnel-structural distance and dynamic loading. Considering that one of the most important parameters of structural control is drift and story displacement, so this important factor will be considered. The results show that tunneling has a direct effect on the rate of structural displacement and increases the structural response. Also, the behavior of the structure is affected by the position of the structure at the ground level and the position of the tunnel and this should be considered during the design phase of the structures.

: Tunnel instability and lining integrity are intimately tied to the creep properties of the surrounding rock. The acquisition of rock mass creep parameters is critical in ascertaining the appropriate timing for lining construction. Nevertheless, creep tests on rock specimens conducted in a controlled setting cannot be straightforwardly extrapolated to rock mass creep analysis. This study performs laboratory-based creep tests on mudstone samples and establishes the corresponding creep constitutive model. Integration of a Mohr-Coulomb element with the Burgers model in series serves to characterise the yield creep behaviour of the rock mass. Additionally, the research outlines a series of 100 orthogonal experiments utilising randomised creep parameters, and formulates a GA-BP neural network inversion model. Employing long-term deformation measurements from the crown and sidewalls of the project site, this study deduces the creep parameters of the mudstone in the investigated tunnel section and examines the prolonged deformation traits of the surrounding rock. Drawing on the deformation traits of the surrounding rock and the forces impacting the primary support and lining structures, this paper evaluates the earliest and latest viable lining casting periods and pinpoints an optimal timing interval for lining implementation. The methodologies employed herein can serve as a benchmark for analogous endeavors internationally.

Traversal time in tunneling effect for ultrasonic waves in tapered waveguides is derived considering its analogy with quantum and electromagnetic waves tunneling. If, as traversal time, the so called phase time is considered, the ultrasonic wavepacket shows the equivalent in acoustics of superluminality i.e. the derived velocity , crosses the limit of bulk transverse ultrasonic waves in the medium of the waveguide that is the equivalent of c in the quantum and electromagnetic cases. Graphs clearly illustrating this so called Hartman effect are obtained confirming the experimental results in the three different fields.

The global usage of veterinary antibiotics is significant. These antibiotics can be released into the aquatic environment and exert toxic effects on non-target organisms. To explore the physiological effects of tetracycline antibiotics on aquatic life, the growth characteristics of and toxin release from the cyanobacterium Microcystis aeruginosa (M. aeruginosa) were studied. Results showed that the toxicity order of the three target antibiotics was TC (tetracycline) > CTC (chlortetracycline hydrochloride) > OTC (oxytetracycline) in terms of inhibition occurrence time and the EC₁₀ and EC₂₅ values. Further, the target antibiotics regulated the production of MC-LR (microcystin-LR) to different degrees. CTC destroyed the M. aeruginosa cells and resulted in a decreased MC-LR release but stimulated the ability to synthesise MC-LR. OTC had a relatively weaker toxicity compared with CTC, while TC was the most toxic among the three antibiotics. Therefore, TC is friendly to the aquatic environment because it simultaneously reduced the intracellular and extracellular MC-LR content. These results aid our understanding of the effects of tetracycline antibiotics on Microcystis aeruginosa, which is important for environmental evaluation and protection. These results are also helpful for guiding the application of veterinary antibiotics in agricultural settings.

Exogenous melatonin, a nutraceutical for maintaining a healthy sleep-wake cycle and managing sleep disorders, requires large, repeated doses due to low bioavailability and short half-life. This necessitates the development of a sustained-release formulation with a longer half-life and sustained plasma concentration. Therefore, exogenous novel 5 mg sustained-release melatonin capsules (Melatonin-SR, test product) were formulated. This open-label cross-over study compared the pharmacokinetics (maximum concentration [Cmax], time to reach Cmax [Tmax], area under the curve [AUC] and elimination half-life [t1/2]) and safety of Melatonin-SR with 5 mg immediate-release melatonin capsules (Melatonin-IR, reference product) after single-dose oral administration in healthy fasting adults. Sixteen participants (aged 18-45 years) were randomized (1:1) to receive either Melatonin-SR or Melatonin-IR in two periods with a 7-day washout period. Melatonin-SR reported lower Cmax (11446.87 pg/mL) compared to Melatonin-IR (22786.30 pg/mL). The mean Tmax of Melatonin-SR and Melatonin-IR was 1.26 h and 0.87 h, respectively. The mean t1/2 of Melatonin-SR (5.10 h) was prolonged by five-fold compared to Melatonin-IR (1.01 h). One adverse event (vomiting) was reported following administration of the Melatonin-IR. Melatonin-SR resulted in higher and sustained plasma melatonin concentrations for an extended period and was well-tolerated. Hence, Melatonin-SR may be a promising nutraceutical for maintaining healthy sleep.

To address the problems of lining cracking and spalling of tunnel structures in coastal areas under the influence of special geologic conditions, environmental loading, and the coupling effect of chemical erosion effects, hybrid fibers were introduced to fly ash concrete in this study. The working performance, compressive strength, split tensile strength, and flexural strength of the hybrid fiber fly ash concrete were tested.The NEL chloride diffusion coefficient under steady-state conditions and the durability test for resistance to sulfate corrosion were carried out. Thus, in-depth analyses of the comprehensive performance of the hybrid fiber fly ash concrete used for tunnel lining were carried out and the damage mechanism were explored. The results showed that the hybrid fiber fly ash concrete exhibited higher strength compared to the control group concrete. However, when the fibers exceeded a certain dosage, the reduction in the working properties of the concrete structure led to the creation of larger pores in the matrix structure, which in turn affected the mechanical properties of the concrete. The most significant reduction in NEL chloride diffusion coefficient was observed when both steel fibers and coconut fibers were added at 1.0 % volumetric parameter, compared to the control group. The apparent state and compressive strength after sulfate corrosion were also minimally affected. This study ensured that the mechanical properties of the concrete were improved and also substantially improved the corrosion resistance of the matrix, providing a scientific basis for the performance improvement of tunnel lining concrete, confirming that steel-coconut fibers hybrid fiber fly ash concrete has a great potential to improve the structural load bearing capacity and durability, and may provide theoretical support for the continued use of tunneling projects and construction processes.

Adenoviruses (Ads) have been extensively manipulated for the development of cancer selective replication, leading to cancer cell death or oncolysis. Clinical studies using E1-modified oncolytic Ads have shown that this therapeutic platform was safe, but with limited efficacy, indicating the necessity of targeting other viral genes for manipulation. To improve the therapeutic efficacy of oncolytic Ads, we treated the entire Ad genome repeatedly with UV-light and have isolated AdUV which efficiently lyses cancer cells as reported previously [1]. In this report, we show that no mutations were observed in the early genes (E1 or E4) of AdUV while several mutations were observed within the Ad late genes which have structural or viral DNA packaging functions. This study also reported the increased release of AdUV from cancer cells. In this study, we found that AdUV inhibits tumor growth following intratumoral injection. These results indicate the potentially significant role of the viral late genes, in particular the DNA packaging genes, to enhance Ad oncolysis.

Wind tunnels are devices that enable researchers to study the flow over objects of interest, the forces acting on them and their interaction with the flow, which is nowadays playing an increasingly important role due to noise pollution. Since the first closed circuit wind tunnel with variable cross-section was built in G¨ottingen, its Prandtl configuration has little change. The wind tunnel with Prandtl configuration has four corners and vanes, more than 50% of the total pressure loss are caused by the corners and vanes. How to reduce the total pressure loss is a world class problem in the wind tunnel design. This study attempts to propose a novel configuration of wind tunnel, where the corners have been replaced by semi-circular tunnel. Sun wind tunnel 2 has only two corners and vanes, while Sun wind tunnel 1 has no corners and vanes at all. It is expected the new wind tunnel can reduce the total pressure loss from 50% to 10%.

A field experiment was conducted for 2 years in Green Tea Laboratory of Saitama Prefectural Agriculture and Forestry Research Center, Iruma, Saitama, Japan from March 2014 to December 2015. Controlled release fertilizers (CRF) or organic fertilizers (ORG) which is the mixture of chicken manure and oil cakewere applied with the amount of 450 kg N ha^-1 yr^-1 in 2014 and 397 kg N ha^-1 yr^-1 in 2015. Nitrous oxide (N₂O) emissionsfrom soil in green tea fields were measured by closed chamber method. The results showed that CRF has significantly lower N₂O compared to ORG. The cumulative N₂O emissions from CRF accounted for 51% of N₂O emissions from ORG fields and 138% of control with no fertilizer treatment. The N₂O flux from the row was higher than that of under the canopy, since fertilizer were applied on the row. However the total emission from the area between the rows was lower than that under the canopy because of the area ratio of row and canopy was 1:5.

Extracellular vesicle (EV) release, which occurs in most eukaryotic cells, has recently been associated with peptidylarginine deiminase (PAD)-driven protein deimination. Evidence points to the involvement of deiminated cytoskeletal proteins and changes in histone deimination. Both PADs and EVs are associated with various pathologies including cancers, autoimmune and neurodegenerative diseases. The elevated PAD expression observed in cancers may contribute to increase in EV shedding observed from cancer cells, contributing to cancer progression. Similarly, elevated PAD expression observed in neurodegenerative diseases may cause increased EV shedding and spread of neurodegenerative EV cargo, contributing to disease progression and pathologies. Pharmacological inhibition of PAD-mediated deimination using pan-PAD inhibitor Cl-amidine, reduced cellular EV release in prostate cancer cells, rendering them significantly more susceptible to chemotherapeutic drugs. Studies on models of central nervous system damage have demonstrated critical functional roles for PADs and neuroprotective effects using PAD inhibitors in vivo, while human neurodegenerative iPSC in vitro models showed evidence of increased protein deimination. Besides using refined PAD inhibitors to selectively manipulate EV biogenesis for novel combination therapies in cancer treatment, we also speculate how EV biogenesis could be targeted via the newly identified PAD-pathway to ameliorate neurodegenerative disease progression.

Interferon-gamma release assays (IGRAs) gained attention for diagnosing latent tuberculosis infection (LTBI) due to their higher specificity compared to the tuberculin skin test (TST). However, IGRA performance varied across different populations. This study evaluated the diagnostic performance of three IGRA assays (TBF-FIA, TBF-ELISA, and QFT-Plus) in Ghana, comparing them among individuals exposed and unexposed to MTB infection. Conducted in TB clinics across three regions, this prospective and cross-sectional study included healthy individuals with no known TB exposure (unexposed group) and patients with confirmed active TB (exposed group). Blood samples were tested using all three assays per manufacturers’ guidelines. The TBF-ELISA showed 3.4% higher sensitivity, but 4.6% lower specificity compared to QFT-Plus. The TBF-FIA had a sensitivity of 78.5%-87.3% and a specificity of 82.9%-90.0%. These findings indicated that while the three IGRA assays offered similar diagnostic accuracy, variations in specificity and limited data on point-of-care assays like TBF-FIA required further investigation.

The research on the impact of excavation of underpass tunnels has already had certain results, but there is a lack of research cases of double-line highway tunnels with oblique angles underpass the existing railway tunnels, especially the method of determining the area of the impact of the dynamic and static loads of the new tunnels and existing trains to be enriched by considering them at the same time. In this paper, based on the tunnel project of the new double-line Shiqian Highway Tunnel with oblique angles underpass the Hurong Railway in Wanshoushan. By constructing a three-dimensional finite element model and simulating the application of static tunnel excavation load, dynamic blasting load and dynamic train operation load of the existing tunnel, the overall displacement of the existing tunnel and the settlement value of the bottom plate of the track surface by the static tunnel excavation load were analyzed. Then, the stresses, vibration speeds and displacements of the tunnel due to the dynamic blasting loads and the dynamic train operation loads were obtained. The results show that: the area of influence of the static loads of the new tunnel excavation on the existing tunnel is divided into three types of perturbations presenting strong, weak and slight; the area affected by the blasting dynamic load of new tunnel excavation is a circular domain with the datum point in the tunnel section as the center; the area affected by the dynamic load of train operation in the existing tunnel is an ellipse with the center of the track surface of the existing tunnel as the datum; there is an anomalous shape in the area affected by the blasting dynamic load of new tunnel excavation and the area affected by the dynamic load of train operation in the existing tunnel.

The dynamic response of the shed-tunnel structure under rockfall impact attracts much attention in recent years. However, the research on the dynamic response of the shed-tunnel structure under rockfall impact mostly focuses on the rockfall single impact, while in practical engineering, the shed-tunnel structure often encounters the rockfall repeated impacts during its service life. Therefore, this research focuses on exploring the dynamic response characteristics of the shed-tunnel structure under the rockfall repeated impacts. First of all, based on the model test of the shed-tunnel under rockfall impact as a reference, the FEM (Finite Element Method)-SPH (Smoothed Particle Hydrodynamics) coupling numerical calculation model is established based on ANSYS/LS-DYNA finite element code. The numerical simulation of the dynamic response of the shed-tunnel structure under rockfall impact is realized, and the rationality of the model is verified. Then, with this model and the full restart technology of LS-DYNA code, the effects of four factors, e.g. rockfall mass, rockfall impact velocity, rockfall impact angle and rockfall shape, on the impact force and impact depth of the buffer layer, the maximum plastic strain and axial force of the rebar, the shed roof vertical displacement and the shed-tunnel plastic strain are studied. These results show that the cumulative deformation and damage of the shed-tunnel structure caused by the rockfall repeated impacts play an important role in the destruction of the shed-tunnel structure, and the special attention should be paid to this issue.

Extensive evidence indicates that activation of P2X7 receptor (P2X7R), an ATP-gated ion channel highly expressed in immune and brain cells, is strictly associated with the release of extracellular vesicles. Through this process, P2X7R-expressing cells regulate non-classical protein secretion and transfer bioactive components to other cells, including misfolded proteins, participating in inflammatory and neurodegenerative diseases. In this review, we summarize and discuss the studies addressing the impact of P2X7R activation on extracellular vesicle release and their activities.

The construction of tunnels excavated by the conventional method in densely populated urban environments requires an adequate characterization of the loads acting on the primary lining during the excavation process to ensure that the ground is deformed and stresses around the tunnel are relieved, simultaneously complying with the failure and serviceability limits of international standards while minimizing damage to nearby structures. In this paper, common lining design criteria are revisited, through the numerical simulation of an instrumented tunnel section which is part of a 4.5 km long metro line currently under construction in Mexico City. Key needs for improvement in current design approaches are identified. The tunnel was instrumented with load cells, extensometers, and topographical references for convergences and divergences. A three-dimensional finite difference model of the instrumented section was developed, and the load transfer mechanisms between the excavated soil and the primary lining was analyzed. Then, the numerical simulation of the contribution of the secondary lining in the overall stability for sustained load was established, along with the expected ground settlements, which can significantly affect nearby structures. Results gathered from this research are key for updating lining design criteria for urban tunnels built in stiff brittle soils.

Molecular transport and quantum tunneling of H2 and H2O molecules through nanoporous gra-phene is studied using computational modeling and first principles density functional theory. It is demonstrated that molecules with sufficiently high kinetic energies can tunnel through the na-nopores. It is also demonstrated that molecules can be trapped in front of the nanopore or behind it. These investigations help us learn the behavior of molecules in and around nanopores of gra-phene. They also help us learn fundamentals of molecular tunneling. We believe, nanoporous gra-phene can play important roles for gas separation and nanofiltration.

new subsonic blower wind tunnel design has been studied both numerically and experimentally, it is also referred to as “blower” wind tunnel. This paper, is initially aimed to address each sequential stage of the wind tunnel design process. Rather than applying the standard method of modelling solely the flow in the test section, a large-scale CFD model of the whole wind tunnel was employed. The loss of every constituent element was calculated and then all the losses are added up to determine the power needed for the wind tunnel operation which is used as “intake fan” boundary conditions in the CFD model. Then, flow uniformity and turbulent intensity measurements in an empty test section using a Pitot-static tube and hot wire anemometer (HWA) were introduced to validate the CFD results. The results showed that flow quality was significantly affected by boundary layer controllers (honeycomb and mesh screens) in the settling chamber and wide-angle diffuser. Investigations were also conducted to evaluate the flow deficit in the wake area behind a convex hump model using HWA. This was additional experimental tests carried out to validate the suitability of the wind tunnel flow aerodynamic research.

We describe electron temperature measurements in the SSX MHD wind tunnel using two different methods. First, we estimate T_e along a chord by measuring the ratio of the C__III 97.7 nm to C_IV 155 nm line intensities using a vacuum ultraviolet monochrometer. Second, we record a biasing scan to a double Langmuir probe to obtain a local measurement of T_e. The aim of these studies is to increase the Taylor state lifetime, primarily by increasing the electron temperature. Also, a model is proposed to predict magnetic lifetime of relaxed states and is found of predict the lifetime satisfactorily. Furthermore, we find that proton cooling can be explained by equilibration with the electrons.

Acute myocardial infarction (AMI) results from vulnerable plaque rupture, causing ischemic cardiomyocyte necrosis and intense inflammation. Paradoxically, this inflammation releases factors that aid heart repair. Recent findings suggest a role for extracellular vesicles (EVs) in intercellular communication during post-AMI cardiac repair. However, EVs’ tissue origin and chemokine profile in the blood of patients with AMI remains unclear. This study characterized EV tissue origin and chemokine receptor profile in the coronary and peripheral blood of patients with AMI. The results reveal that vesicles isolated from coronary and peripheral blood plasma are enriched in tetraspanin (CD9) and express CD81+, CD90+, and CD144+. The vesicle size ranged between 145 and 162 nm, with the control group exhibiting smaller vesicles than the AMI group. Furthermore, all vesicles expressed CCR6+ and CXCR3+, whereas a small percentage expressed CCR4+. In addition, a decrease in CXCR3+ and CCR6+ positivity was observed in coronary and peripheral blood vesicles compared with the control. Non-difference was found in the coronary and peripheral blood for the CXCR3+ and CCR6+ markers. In conclusion, our study demonstrates, for the first time, changes in the number of extracellular vesicles expressing CD144+, CXCR3+, and CCR6+ in the peripheral circulation of patients with AMI. Extracellular vesicles present in the peripheral circulation of patients with AMI hold excellent promise as a potential diagnostic tool.

This study investigated the effect of replacing part of the dietary soybean meal with either polymer-coated urea or gelatinized starch urea on the performance, nutrient digestibility, blood biochemical indexes, ruminal fermentation and rumen microflora of Angus heifers. The urea release profiles of two kinds of slow-release urea were evaluated in vitro and indicated a superior nitrogen retention with the polymer-coated urea. 210 purebred Angus cattle (BW = 314.26 kg) were divided into three groups: no urea group (CON), polymer-coated urea group (PCU), gelatinized starch urea group (GSU), 20g/kg polymer-coated urea or 25g/kg gelatinized starch urea was used to replace part of soybean meal in the concentrate feed respectively according to the principle of iso-metabolic energy and iso-nitrogenous. During the whole experiment, the ADG of PCU group was higher than both the GSU group and the CON group. The feed-weight ratio of the PCU group was significantly lower than both the GSU group and the CON group during the 90-day feeding period. The ADF apparent digestibility in the PCU group was significantly higher than that of the CON group, and extremely significantly higher than that of the GSU group. On the 86th day, the ALB content in the PCU group was significantly higher than that in the CON group. The contents of acetic acid and butyric acid, total volatile fatty acid and propionic acid were significantly higher in the PCU group than in the CON group. Bacterial diversity analysis found that the abundance of Firmicutes was higher in the PCU group than that in the GSU group and the CON group at the phylum level, and inverse result was observed in Bacteroidetes. The abundance of Paraprevotella was higher in the PCU group, whereas higher abundance of Prevotella was found in the GSU group at the genus level. These results indicate that both polymer-coated urea and gelatinized starch urea can replace part of soybean meal in the diet, and the amount of substitution in this trial had no diverse effect on the performance of Angus heifers, and the effect and economic benefits brought by polymer-coated urea were better than gelatinized starch urea.

Aedes albopictus is considered one of the major invasive species in the world and can transmit viruses such as dengue, Zika, or chikungunya. The Sterile Insect Technique (SIT) can be used to suppress the native populations of Ae. albopictus. To support the development of the release strategy during the SIT application, Mark-Release-Recapture (MRR) studies are crucial. Mean-while, weather conditions can affect the MRR trial’s results and it is critical to understand the influence of climatic factors on the results. In October 2022 in Faro, Southern Portugal, 84,000 ir-radiated sterile males were released for three consecutive weeks and mosquitoes were recapture by Human Landing Collections (HLC) one, two, four and six days after. Generalised linear models with a negative binomial family and log function were used to estimate the factors asso-ciated with the number of recaptured mosquitoes, prevalence ratios, and the 95% confidence in-tervals (CI). A total of 84,000 sterile male mosquitoes were released, with 528 recaptured (0.8%) by HLC. The prevalence of recaptured mosquitoes was 23% lower when the wind intensity was moderate. Sterile-marked males had an average median distance travelled of 88.7 m. Median probability of daily survival and the average life expectancy were 61.6% and 2.1, respectively. Wild male population estimates was 443.33 males/ ha. Despite no statistically significant asso-ciation was found with humidity, temperature and precipitation, it is crucial to consider weather conditions during MRR trials analyses to obtain the best determinants estimation and a more ef-ficient application of SIT in an integrated vector management program.

This paper presents geometric analyses of welded frames after free relaxing and vibratory stress relief (VSR). Respected frames were tested components of a prototype packaging machine. Two types of relaxation were carried out to remove stresses introduced as a result of welding process. One of the frame was subjected to free relaxing, while the other one to accelerated vibration relaxing. Detection of the frame geometry changes was performed using a photogrammetric system. In addition, an evaluation of the geometry change was conducted for fifteen variants of steel frame support. A comparative analysis of the geometric deviations of the frames after free and vibratory stress relief confirmed the assumption that the frame after vibration stress relief better reproduces the nominal dimensions. Nevertheless, it should be emphasized that after vibratory stress relief the frame is not subject to further deformation, which is a desirable effect. In the case of free relaxing, the frame undergoes dimensional changes in a random manner. In summary, carrying out accelerated vibratory stress relief allows control of spontaneous dimensional changes in the designed frame of a packaging machine resulting from spontaneous relaxation of stresses arising from the welding process. The shortening of the relaxation process of the welded frame is also an unquestionable advantage.

Amidst increasing awareness of diet-health relationships, plant-derived bioactive peptides are recognized for their dual nutritional and health benefits. This study investigates bioactive peptides released after Alcalase hydrolysis of protein from chachafruto (Erythrina edulis), a nutrient-rich South American leguminous plant, focusing on their behavior during simulated gastrointestinal digestion. Evaluating their ability to scavenge radicals, mitigate oxidative stress, and influence immune response biomarkers, the study underscores the importance of understanding peptide interactions in digestion. Methods included previous enzymatic hydrolysis with Alcalase to obtain peptides, and results show significant radical scavenging and oxidative stress protection by chachafruto peptides. These findings highlight the potential of chachafruto bioactive peptides in functional foods and nutraceuticals, supporting human health through dietary interventions.

Management of chronic inflammation and wounds has always been a key issue in the pharmaceutical and healthcare sector. Curcumin (CCM) is an active ingredient extracted from turmeric rhizomes that has antioxidant, anti-inflammatory, and antibacterial activities, thus showing significant effectiveness toward wound healing. However, its shortcomings such as poor water solubility, poor chemical stability and fast metabolic rate limit its bioavailability and long-term use. In this context, hydrogels appear to be a versatile matrix for carrying and stabilizing drugs due to the biomimetic structure, soft porous microarchitecture, and pleasant biomechanical properties. The drug loading/releasing efficiencies can also be controlled by use of highly crystalline and porous metal organic frameworks (MOFs). Here, a flexible hydrogel composed of sodium alginate (SA) matrix and CCM-loaded MOFs was constructed for long-term drug release and antibacterial activity. The morphology and physicochemical properties of composite hydrogels were analyzed by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), ultraviolet visible spectroscopy (UV-Vis), Raman spectroscopy and mechanical property tests. The results showed that the composite hydrogel was highly twistable and bendable to mechanically comply with human skin. The as-prepared hydrogel could capture efficient CCM for slow drug release as well as effective killing of bacteria. Therefore, such composite hydrogel is expected to provide a new management system for chronic wound dressings.

Preventing or treating infections at implantation sites where the risk of bacterial contamination is high requires the development of intelligent drug delivery systems. In this work, honeycomb structures as a potential drug carrier were obtained for the first time in a fast, one-step anodization process of titanium grade 4, lasting only 60 seconds. Fourth generation oxide nanotube layers were obtained from an aqueous solution of 0.5% AgNO3 in the voltage range from 50 to 80 at 15(1) °C. The FE-SEM method showed the length of the oxide nanotubes from 1.02(2) µm at 50 V to 230(8) nm at 80 V. The EDS analysis revealed that during anodizing, silver particles are deposited on the Ti G4 up to 2.2(5) wt.%. Electrochemical measurements by open circuit potential and anodic polarization curves methods proved the improvement of in vitro corrosion resistance as a result of Ti G4 anodizing. Assessment of the anodized Ti G4 as gentamicin sulfate carrier carried out using ATR-FTIR and UV-VIS absorption spectroscopy revealed that the obtained oxide nanotube layers can be used for application of drugs directly to the tissue around the implant. This method of application allows full use of the therapeutic dose of the antibiotic used.

Bionic robotic hand can perform many movements similar to human hand. But there is still a significant gap in manipulation between robot and human hand. It is necessary to understand the finger kinematics and motion patterns of human hand to improve the performance of robotic hand. This study aimed to comprehensively investigate normal hand motion patterns by evaluating the kinematics of hand grip and release in healthy individuals. The data corresponding to rapid grip and release were collected from the dominant hand of 22 healthy people by sensory glove. The kinematics of 14 finger joints were analyzed, including the dynamic range of motion (ROM), peak velocity, joint sequence and finger sequence. The results show that the proximal interphalangeal (PIP) joint had a largest dynamic ROM than metacarpophalangeal (MCP) and distal interphalangeal (DIP) joints. Besides, the PIP joint had the highest peak velocity, both in flexion and extension. For joint sequence, the PIP joint moved prior to the DIP or MCP joints during flexion, while extension started in DIP or MCP joints, followed by PIP joint. Regarding the finger sequence, the thumb started to move before four fingers, and stopped moving after the fingers during both grip and release. This study explored the normal motion patterns in hand grip and release, which provided kinematic reference for the design of robotic hand and thus contribute to its development.

This paper introduces a method for tunnel point cloud and BIM model integration and cross-section monitoring, providing information to analyse tunnel cross-sections and surrounding rock deformation, and support for tunnel maintenance and reconstruction. Three types of data are processed for the integration: laser scanning point cloud, BIM tunnel model and terrain model from oblique photogrammetry. An adaptive BIM modelling scheme is proposed for tunnels with alien structures. Precise spatial registration of the data sets is conducted by applying singular value decomposition (SVD) algorithm to calculate transformation parameters from the point cloud model to the BIM model. Since the tunnel central line has high-order derivability, a cross-section calculation method based on tangent vector is proposed to obtain the cross-sectional profile of tunnels at any mileage. The proposed method has been verified by applying it to a tunnel reconstruction project. The experiment results show that the tunnel point cloud and the BIM model were highly coincident after the integration. The developed program can effectively get the cross-section of the tunnel at any mileage, and correctly express the spatial relationship between the BIM tunnel, the point cloud of tunnel and the external mountainous terrain.

Due to poor ventilation conditions in the tunnel, if gas pipeline leaks, the consequence of the accident will be more serious. Therefore, before the emergency repair, gas in the tunnel needs to be excharged so as not to explode during the repair process. Therefore, it is necessary to study the ventilation of gas in the tunnel. Based on the computational fluid dynamics (CFD) theory and taking the Yanyingshan tunnel section of China-Myanmar pipeline as an example, this paper uses Fluent software to establish the leakage model of the gas pipeline and fan model in the tunnel and analyzes the influence of different fan locations and number of fans on gas concentration. It can be concluded that: (1) the use of press-in method makes it more efficient to discharge gas out of the tunnel. (2) In order to make ventilation efficient, the fan should be arranged in a higher position and needs to be at a distance from the top of the tunnel. (3) Parallel use of two fans has better ventilation effect than single fan.

Based on the nonlinear failure criterion and modified tangential technique, the upper bound solutions of supporting pressure on the deep tunnel face were obtained under pore water pressure conditions. The influence of parameters on the supporting pressure and collapse range was investigated according to the unlimited block failure mechanism. It is found that the upper bound solutions of supporting pressure increase with the growth of the nonlinear coefficient and pore water pressure coefficient. The collapse range of the tunnel face scales out with the increase of the nonlinear coefficient and shrinks when increasing the pore water pressure coefficient. Moreover, with the increase of the nonlinear coefficient, the impact strength on supporting pressure and collapse range declines gradually. According to the calculating results, it is manifest that both the pore water pressure and nonlinear criterion factors have negative impacts on the stability of the tunnel face. Thus, more attention should be paid to these parameters to ensure face stability in deep tunnel construction.

In this nano era, nanomaterials and nanostructures are popular in developing novel functional materials. However, the combinations of nanoproducts with materials at micro and macro scale can open new routes for conceiving novel materials with an improved or even new functional performances. In this study, a brand-new hybrid, containing both nanofibers and particles having a microsize, was fabricated using a sequential electrohydrodynamic atomization (EHDA) process. Firstly, the microparticles loaded with drug (berberine hydrochloride, BH) molecules in the cellulose acetate (CA) were fabricated using a solution electrospraying process. Later, these microparticles were suspended into a co-dissolved solution containned BH and a hydrophilic polymer (polypyrrolidone, PVP), and were co-electrospun into the nanofiber/microparticle hybrids. The EHDA processes were clearly recorded, and the resultant products showed a typical hybrid topography, with microparticles distributed all over the nanofibers, which was demonstrated by SEM assessments. FTIR and XRD demonstrated that the components within the hybrids were presented in an amorphous state and have fine compatibility with each other. In vitro dissolution tests verified that the hybrids were able to provide the designed dula-step drug release profiles, a combination of the fast release step of BH from the hydrophilic PVP nanofibers through an erosion mechanism and the sustained release step of BH from the insoluble CA microparticles via a typical Fickian diffusion mechanism. The present protocols pave a new way for developing trans-scale functional materials.

The aim of this paper was to determine the soil phosphorus release risk from drained and re-wetted peatlands under different landcovers. The study was carried out at 10 soil profiles (organic soils, frequently with mursh in the topsoil, developed from low peat with various degrees of decomposition, on mineral subsoil or gyttja) located south-west of Lake Kośno nature reserve in northern-central Europe (north-eastern Poland). The soil samples were collected from the depths of 0-30 cm, 50-80 cm and 100-130 cm during spring, summer and autumn (in April, July, and October). In the laboratory, the following soil properties were determined: ash content, soil reaction, content of total organic carbon, total nitrogen, total and plant-available phosphorus. Gyttja formations and hemic peats had the highest total P content (6.77 g∙kg-1 and 2.29 g∙kg-1, respectively). Murshes contained twice less P (1.18 g∙kg-1). In spring, more plant-available phosphorus (AP sp) was released in murshes (0.29 g∙kg-1) than in peats (0.07-0.14 g∙kg-1). In the summer, higher amounts of plant-available P were stated in fiber peats (0.37 g∙kg-1) than in murshes (0.26 g∙kg-1), whereas in autumn, the amounts of P in murshes (0.22 g∙kg-1) and peats (0.21-0.23 g∙kg-1) did not vary. Generally, average contents of AP were the highest in murshes (0.26 g∙kg-1) and fiber peats (0.25 g∙kg-1), and the lowest in sapric peats (0.15 g∙kg-1). The release of phosphorus from organic compounds or binding of P by organic matter (immobilization) depends on the C:P ratio in plant residues and soil. If it is wide (>300), P is bound, if it is narrower (150–200), P is released. In the tested soil formations, the C:P ratio was frequently above 300. Only in some murshes and gyttjas the C:P ratio was below 150, which may indicate a risk of phosphorus release to groundwaters.

Renewable resources gain increasing interest as source for environmentally benign biomaterials, such as drug encapsulation/release compounds, and scaffolds for tissue engineering in regenerative medicine. Being the second largest naturally abundant polymer, the interest in lignin valorization for biomedical utilization is rapidly growing. Depending on resource and isolation procedure, lignin shows specific antioxidant and antimicrobial activity. Today, efforts in research and industry are directed toward lignin utilization as renewable macromolecular building block for the preparation of polymeric drug encapsulation and scaffold materials. Within the last five years, remarkable progress has been made in isolation, functionalization and modification of lignin and lignin-derived compounds. However, literature so far mainly focuses lignin-derived fuels, lubricants and resins. The purpose of this review is to summarize the current state of the art and to highlight the most important results in the field of lignin-based materials for potential use in biomedicine (reported in 2014–2018). Special focus is drawn on lignin-derived nanomaterials for drug encapsulation and release as well as lignin hybrid materials used as scaffolds for guided bone regeneration in stem cell-based therapies.

UAV has become powerful devices for both practitioners and researchers. In recent years, there has been a substantial growth in the usage of UAV for a wide range of applications in research and engineering. UAV are mostly utilized for image capturing techniques due to their time savings, low cost, minimum field work, and high precision. The purpose of this study is to generate an accurate and reliable 3D modelling process using UAVs photogrammetric technology; hence this study allows the techniques to evaluate the practicability of modelling and mapping inaccessible tunnels using images recorded by UAVs and photogrammetry. As a result, the approach was always employed to depict the true state of the place. This research incorporates three experiments. The first experiment is to build a 3D model using only one-directional light source and evaluate the accuracy of 3D photogrammetric model and conducted at the concrete tunnel. The second one is to build a 3D model of underground sewer tunnel using different light sources one-directional and omni-directional. The last experiment was to build 3D model using an UAV system which is developed based on first and second experiment’s result, evaluate an accuracy of 3D photogrammetric model and conducted at the tunnel named in the research as a “pedestrian tunnel. There is certain limitation in this study such as Adding a payload to a drone changed its weight distribution, which affected its stability. If the payload was not properly balanced, it caused the drone to fly unevenly, making it more difficult to control.

The study takes into account different classes of tunnel boring machines (TBMs), with the aim of identifying correlation models which are meant to estimate, at a preliminary design phase, the construction time of a tunnel and to evaluate the mechanical and operational parameters of the TBMs, starting from the knowledge of the tunnel length and/or the excavation diameter. To achieve this goal, first of all a database was created, thanks to the collection of the most meaningful technical parameters from a large number of tunnels; afterward, it was statistically analysed through Microsoft Excel. In a first phase, forecasting models were identified for the three types of machines investigated, separately for compact rocks (open TBM) and fractured rocks (single and double shield TBM). Then, the mechanical parameters collected through the database were analysed, with the aim of obtaining models that take into account, in addition to the type of TBM, the geological aspect, and the type of rock characterising the rock mass. Finally, the validation of the study was proposed in a real case, represented by the Moncenisio base tunnel, a work included in the new Turin–Lyon connection line. The estimated values were compared with the real ones, in order to verify the accuracy of the experimental models identified.

The surface defects of shield subway tunnel can significantly affect the serviceability of the tunnel structure and may compromise the operation safety. To effectively detect the multiple surface defects, this research employs a tunnel inspection trolley (TIT) based on the mobile laser scanning technique. By conducting the inspection of the shield tunnel on a metro line section, various surface defects are identified by the TIT, including water leakage defect, dislocation, spalling, cross-section deformation, etc. To explore the root causes of the surface defects, the association rules between different defects are calculated via an improved Apriori algorithm. Results show that: i) there are significant differences in different association rules of various surface defects of the shield tunnel; ii) the average confidence of the association rule “dislocation & spalling → water leakage” is as high as 57.78%, indicating that most of the water leakage defects are caused by dislocation and spalling of the shield tunnel in the sections being inspected; iii) the weakest rule appears at “water leakage → spalling”, with the average confidence of 13%. The association analysis can be used in predicting the critical defects influencing the structural reliability and operation safety, such as water leakage, and optimizing the construction and maintenance work for the shield subway tunnel.

Mosquitoes carrying endosymbiotic bacteria called Wolbachia are being released in mosquito and arbovirus control programs around the world. Open field releases of Wolbachia-infected male mosquitoes have achieved over 95% population suppression, while the replacement of populations with Wolbachia-infected females is self-sustaining and can greatly reduce local dengue transmission. Despite many successful interventions, significant questions and challenges lie ahead. Wolbachia, viruses and their mosquito hosts can evolve, leading to uncertainty around the long-term effectiveness of a given Wolbachia strain, while few ecological impacts of Wolbachia releases have been explored. Wolbachia strains are diverse and the choice of strain to release should be made carefully, taking environmental conditions and the release objective into account. Mosquito quality control, thoughtful community awareness programs and long-term monitoring of populations are essential for all types of Wolbachia intervention. Releases of Wolbachia-infected mosquitoes show great promise, but existing control measures remain an important way to reduce the burden of mosquito-borne disease.

The quality and shelf-life of NCS (Non-centrifugal sugar) mainly depend on the moisture content present in it. NCS formed by the current practice of open sun drying contains moisture substantially greater than the acceptable level of 3%. This paper presents the work taken up to design a tunnel dryer to attain require moisture content in granular NCS for various load conditions. Initially, an experimental investigation had been carried out on a laboratory scale dryer to achieve required moisture content (< 3%) for various load conditions. This experimental data was used for validating two drying models and found that one of the models is best suitable for designing an industrial-scale dryer. For various load conditions on each tray and dryer exit temperature, nine different cases were arrived at. The number of trucks, trays, drying time and energy requirements were computed using the suitable theoretical model. Tunnel dryer with a length of 18 m, a height of 1.2 m, a width of 1 m, number of trucks of 18 and 24 number of trays on each truck was found to be the suitable dryer to dry 1 tone of NCS based on the minimum energy requirement of 176.49 MJ, and a minimum drying time of 68 minutes.

A novel scaffold design has been created to enhance tissue engineering and regenerative medicine by optimizing the controlled, prolonged release of hepatocyte growth factor (HGF), a powerful chemoattractant for endogenous mesenchymal stem cells. We present a new stacked scaffold that is made up of three different fibrin gel layers, each of which has HGF integrated into the matrix. The design attempts to preserve HGF's regenerative properties for long periods of time, which is necessary for complex tissue regeneration. These multi-layered fibrin gels have been mechanically evaluated using rheometry, and their degradation behavior has been studied using D-Dimer ELISA. Understanding the kinetics of HGF release from this novel scaffold configuration is essential for understanding HGF's long-term sustained bioactivity. A range of cell-based tests were carried out to verify the functionality of HGF following extended incorporation. These tests included 2-photon microscopy using phalloidin staining to examine cellular morphology, SEM analysis for scaffold-cell interactions, and scratch and scatter assays to assess migration and motility. The analyses show that the novel stacking scaffold promotes vital cellular processes for tissue regeneration in addition to supporting HGF's bioactivity. This scaffold design was developed for in situ tissue engineering. Using the body as a bioreactor, the scaffold should recruit mesenchymal stem cells from their niche thus combining the regenerative abilities of HGF and MSCs to promote tissue remodeling and wound repair.

Recent advancements in nanotechnology have led to the development of multifunctional iron oxide nanoparticles, presenting new opportunities in cancer therapy. This study aimed to synthesize and evaluate citric acid-coated/ folic acid conjugated nanoparticles loaded with doxorubi-cin and investigate their efficacy in experimental tumor models. For synthesis, controlled co-precipitation method was employed to produce highly dispersive, multifunctional nanofluids with a narrow size distribution of iron oxide nanoparticles. Nanoparticles were characterized using Dynamic Light Scattering (DLS) and Electrophoretic Light Scattering (ELS) for size distribution and zeta potential, X-ray Diffraction (XRD) and Transmission Electron Microscopy (TEM) for structure and morphology, Vibrating Sample Magnetometry (VSM) for magnetic properties, and UV-Visible (UV-Vis) and Fourier-Transform Infra-red (FTIR) spectroscopy for modification confirmation. In vitro experiments employed RM1 (prostate cancer) and MEC1 (Chronic lymphocytic leukemia) cell lines to assess cytotoxicity and drug delivery efficiency. Fluorescence microscopy confirmed the intracellular delivery of doxorubicin by these nanoparticles, highlighting their potential for targeted therapy. As a result, nanoparticles conjugated with folic acid showed reduced efficacy over time. This study underscores the critical role of nanoparticle modifications in optimizing therapeutic outcomes. Future research should focus on further refining nanoparticle formulations and long-term effects in vivo, for development of effective and safe agents for targeted cancer treatment.

Sustained-release drug delivery systems have evolved significantly over the years, playing a pivotal role in pharmaceutical research and enhancing patient care [1]. This abstract synthesizes key insights from various references to highlight the noteworthy advancements in this field. Recent research has emphasized the importance of understanding drug properties and their impact on sustained-release system design [2] [9]. These advancements enable tailoring drug delivery to optimize therapeutic outcomes [2] [9]. Incorporating innovative technologies such as nanotechnology [1], biodegradable polymers [3], and matrix systems [4] has led to the development of more efficient and patient-friendly sustained-release systems [1] [3] [4] Moreover, the concept of personalized medicine is gaining prominence [5], opening doors to individualized drug delivery strategies [5]. These strategies promise to enhance treatment efficacy while minimizing adverse effects [5]. Theoretical analyses, as exemplified by Higuchi’s work [6], continue to shape the understanding of sustained-release mechanisms [6]. Furthermore, studies on enteric-coated timed-release tablets [10]. highlight advancements in specific drug formulations to meet patient needs [10]. In conclusion, advancements in sustained-release drug delivery systems reflect a dynamic landscape where drug properties, innovative technologies, and personalized approaches converge to improve patient outcomes and drug therapy [7] [8] [10].

Deformation monitoring is beneficial to ensure the service safety of long tunnel. An three-direction (vertical, transverse and axial) deformation estimation method using long-gauge fiber Bragg grating (FBG) sensing technology is proposed and applied to a long tunnel by integrating mechanical analysis and field monitoring during the service state. The key issues of the proposed method for identifying the three-direction deformation are discussed, such as establishing the separation model of coupling strain on cross section, deriving the theory of deformation identification in three directions, and determining the sensor layout of the long tunnel. A major advantage of the proposed method is that the three-direction deformation of the tunnel can be monitored in real time using distributed long-gauge strain sensors. The numerical analysis and field test results verify the feasibility of the proposed method.

In the construction of shield crossing existing mined tunnel without load, it is imperative to develop corresponding design standards that reflect actual engineering force characteristics to ensure the successful completion of tunnel construction. This research uses The MIDAS-GTS finite element software to facilitate the creation of a numerical model of the shield structure for an air-push-over mine tunnel project in Changsha, China, investigating the stress field’s evolution during shield construction, and calculating the maximum positive and negative bending moments and maximum axial forces for different structures and other force states under various construction conditions. This study's findings informed the design and construction optimisation of the shield tunnelling empty-push method. The outcomes of this numerical simulation led to several key findings: (1) The soil density exerted a significantly greater impact on the internal forces of the initial support structure than both the tunnel depth and soil Poisson's ratio. Additionally, a sudden shift in internal forces occurred within the 300-350 mm range when the lining thickness was altered. (2) Factors such as the tunnel depth, soil density, soil Poisson's ratio μ, and lining thickness have a similarly influenced internal forces of the segment and the initial support. Notably, the backfill layer thickness significantly affected the segment’s maximum axial force causing an abrupt change of approximately 300 mm. (3) Under the shield machine equipment’s weight constraint, it is essential to control the guide rail’s thickness, to prevent it from becoming overly large.

Empirical models help us understand the process of plant residue decomposition and nutrient release into the soil. The objective of this study was to determine an appropriate model to describe the decomposition of hairy vetch (Vicia villosa Roth) and cereal rye (Secale cereale L.) cover crop (CC) residue and nitrogen (N) release. Data pertaining to above and belowground CC residue mass loss and N release for up to 2633 cumulative decomposition degree days (112 d) after litterbag installation were obtained from two cropping system experiments, one conducted in 2015 and the other in 2017 and 2018 at the humid subtropical environment of southern IL, USA. Six exponential and two hyperbolic models were fit to percent mass and N remaining data to find the one with minimum Akaike Information Criterion (AIC) and residual sum of squares. Modified three-parameter single exponential and two- or three-parameter hyperbolic models best met the assumed criteria of selection for above and belowground CC residue, respectively. Fitting a double exponential model to a combined data for percent mass and N remaining, which identified two mass and N pools, a fast and a slow pool with different rate constants. A five-parameter double exponential with an asymptote met the preset criteria and passed all tests for normally distributed population, constant variance, and independence of residuals at α = 0.05 when fit to combined data of hairy vetch shoot mass and N remaining. However, a two-parameter hyperbolic and three-parameter asymptotic hyperbolic model provided the best fit to a combined data of cereal rye shoot mass and N remaining, respectively. Both hyperbolic decay models showed a good fit for belowground mass decomposition and N release for both CCs. Cereal rye had poorer fit than hairy vetch for mass and N remaining of both above and belowground mass. The best-selected decay models can be used to estimate the decomposition and N release rates of hairy vetch and cereal rye above and belowground residue in a similar environment.

Corticosterone, an end product of the hypothalamic-pituitary-adrenal (HPA) axis, is a crucial stress hormone. Dysregulated HPA axis and corticosterone release play pivotal roles in the onset and persistence of symptoms of stress-related psychiatric disorders such as anxiety. The intake of nutrients, probiotics, and prebiotic supplements decreases blood corticosterone levels. The dipeptide L-carnosine is composed of beta-alanine and L-histidine and is commercially available as a nutritional supplement for recovery from fatigue. L-carnosine is involved in stress-induced corticosterone responses and anxiety behaviors in rodents. Here, we assessed the effect of L-carnosine in CD157 knockout (KO) mice, a murine model of autism spectrum disorder (ASD). The uptake of L-carnosine suppressed the increase in plasma corticosterone levels in response to acute stress and attenuated anxiety-like behaviors in CD157 KO mice. These results suggest that L-carnosine supplementation may relieve anxiety by suppressing excessive stress responses in individuals with ASD.

In tunnel excavation with boring machines, the tunnel face is supported to avoid collapse and minimise settlement. This article proposes the use of reinforcement learning, specifically the Deep Q-Network algorithm, to predict the face support pressure. The approach is tested both analytically and numerically. By using the soil properties ahead of the tunnel face and the overburden depth as the input, the algorithm is capable of predicting the optimal tunnel face support pressure, adapting to changes in geological and geometrical conditions.

The accurate of model attitude angel plays an important role on the aerodynamic test results in the wind tunnel test. The original method applies the spherical coordinate system transformation to obtain attitude angel calculation. The model attitude angel is obtained by coordinate transformation and spherical surface mapping applying the nominal attitude angel (the balance attitude angel in the wind tunnel coordinate system) indicated by the mechanism. First, the coordinate transformation of this method is not only complex but also difficult to establish the transformed relationship between the space coordinate systems especially after many steps of coordinate transformation, moreover it cannot realize the iterative calculation of the interference relationship between attitude angels; Second, during the calculate process to solve the problem the arc is approximately used to replace the straight line, the angel for the tangent value, and the inverse trigonometric function is applied. Therefore, in the calculation of attitude angel, the process is complex and inaccurate, which can be solved approximately when calculating small attack angel. However, with the advancing development of modern aerodynamic unsteady research, the aircraft tends to develop high or super large attack angel and unsteady research field. According to engineering practice and vector theory, the concept of vector angel coordinate system is proposed for the first time, and the vector angel coordinate system of attitude angel is established. With the iterative correction calculation and avoiding the problem of approximate and inverse trigonometric function solution, the model attitude calculation process is carried out in detail, which validates that the calculation accuracy and accuracy of model attitude angels are improved. Based on engineering and theoretical methods, a vector angel coordinate system is established for the first time, which gives the transformation and angel definition relations between different flight attitude coordinate systems, that can accurately calculate the attitude angel of the corresponding coordinate system and determine its direction, especially in the channel coupling calculation, the calculation of the attitude angel between the coordinate systems is only related to the angel, and has nothing to do with the change order s of the coordinate system, which simplifies the calculation process.

The formulation and analytic solution of a new mathematical model with constitutive curvature for analysis of tunnel ventilation shaft wall is proposed. Based on the Mindlin-Reissner theory for thick shells, this model also takes into account the shell constitutive curvature and considers an expression of the shear correction factor variable (αn) in terms of the thickness (h) and the radius of curvature (R). The main advantage of the proposed model is that it has the possibility to analyze thin, medium and thick tunnel ventilation shafts. As a result, two comparisons were made: the first one, between the new model and the Mindlin-Reissner model without constitutive curvature with the shear correction factor (α_n=6/5) as a constant, and the other, between the new model and the tridimensional numerical models (solids and shells) obtained by finite element method for different slenderness ratios (h/R). The limitation of the proposed model is that it is to be formulated for a general linear-elastic and axial-symmetrical state with continuous distribution of the mass.

Introduction: Established predictors for COVID-19 related mortalities are diverse, with cytokine release syndrome (CRS), a key intermediator to the case fatalities being dominant and multi-faceted. The impact of these several risk factors on coronavirus mortality have been previously reported in several meta‐analyses limited by small sample sizes and premature data, and CRS not fully being accounted for. The objective of this systematic review and meta-analysis was to evaluate the evidence on the risk of COVID-19 related CRS and mortality with HIV serostatus using published data, and a meta-regression to account for possible covariates. Method: Electronic databases including Google Scholar, Cochrane Library, Web of Sciences (WOS), EMBASE, Medline/PubMed, COVID-19 Research Database, and Scopus, were systematically searched till 30th February, 2022. All human studies were included irrespective of publication date or region. Twenty-two studies with a total of 19,783,097 patients detailing COVID-related mortality and eleven with a total of 2,005,274 were included. To pool the estimate, a random-effects model with risk ration as the effect measure was used. Moreover, publication bias and sensitivity analysis were evaluated followed by meta-regression. The trial was registered (CRD42021264761) on the PROSPERO register. Results: The findings were consistent in stating the contribution of HIV infection for COVID-19 related CRS and mortality. The cumulative COVID-19 related mortality and CRS was 110270 (0.6%) and 48863 (2.4%) with total events of 2010 (3.6%), 108260 (0.5%) and 837(4.6%), 48026 (2.4%) among HIV-positive and negative persons respectively. HIV infection showed an increased risk of COVID-19 related CRS and mortality [RR= 1.48, 95% CI (1.16, 1.88) (P=0.002)] and [RR =1.19, 95% CI (1.02 -1.39) (P=0.00001)] respectively, both with substantial heterogeneity (I² > 80%). The true effects size in 95% of all the comparable populations fell between 0.64 to 2.22 and 0.67 to 3.29 for mortality and CRS respectively. MC studies and COVID-19 mortality with HIV infection showed a significant association [RR = 1.305, 95% CI (1.092 -1.559) (P = 0.003)], similar to studies conducted in America (RR = 1.422, 95% CI 1.233–1.639) and South Africa (RR = 1.123, 95% CI 1.052–1.198). HIV infection showed a risk for ICU admission [(P=0.00001) (I² = 0%)] and mechanical ventilation [(P=0.04) (I² = 0%)] as parameters of CRS. Furthermore, risk of COVID-19 related CRS is influenced by the year a study was conducted (R² = 0.55) and the region (R² = 0.11) same for mortality (R² = 0.60). The variance proportion explained by covariates was significant for CRS (I² = 86.5%, Q = 73.99, df = 10, P = 0.0000) (R² = 0.78) and mortality (I² = 87.5%, Q = 168.02, df = 21, p = 0.0000) (R² = 0.67). Conclusion: Our updated meta-analysis indicated that HIV infection was significantly associated with an increased risk for both COVID-19 – CRS and mortality, which might be modulated by regions, study setting and year. Risk for ICU admission and mechanical ventilation are the key indicators of CRS. We believe the updated data further anchoring CRS will contribute to more substantiation of the findings reported by similar earlier studies (Dong et al., 2021; K. W. Lee et al., 2021; Massarvva, 2021; Mellor et al., 2021; Ssentongo et al., 2021)

Zero-rate output (ZRO) drift induces deteriorated micro-electromechanical system (MEMS) gy-roscope performances, severely limiting its practical applications. Hence, it is vital to explore an effective method toward ZRO drift reduction. In this work, we conduct an elaborate investigation on the impacts of the internal and packaging stresses on the ZRO drift at the thermal start-up stage, and propose a temperature-induced stress release method to reduce the duration and magnitude of ZRO drift. Self-developed high-Q dual mass tuning fork gyroscopes (TFGs) are adopted to study the correlations between temperature, frequency and ZRO drift. Furthermore, a rigorous finite element simulation model is built based on the actual device and packaging structure, revealing the temperature and stresses distribution inside TFGs. Meanwhile, the relationship between temperature and stresses are deeply explored. Moreover, we introduce a temperature-induced stress release process to generate thermal stresses and reduce the temperature-related device sensitivity. By this way, the ZRO drift duration is drastically reduced from ~2000 s to ~890 s, and the drift magnitude decreases from ~0.4 °/s to ~0.23 °/s. This stress release method achieves a small bias instability (BI) of 7.903 °/h and a low angle random walk (ARW) of 0.792 °/√h, and the long-term bias performance is significantly improved.

The calculation of the release of liquid hazardous chemicals storage tanks is an important part of the quantitative risk assessment of accidents. This paper mainly establishes a continuous real–time release model based on the instantaneous mass flow Q_m model. Meanwhile, the software function module was analyzed, and programming software was developed using C# language for model solving. A series of experiments for repeated leakage tests was designed and the discharges through three small holes with different heights for 200 s were observed. The results show that the continuous real–time leakage model is effective, and the deviation between theoretical and experimental release amounts are within a reasonable range. The higher the liquid level above the leak hole is, and the smaller the height of the leak hole from the ground is, the greater the flow rate at the leak orifice is and the smaller discharge rate change is. Therefore, the deviation between the theoretical release amount M_t and the experimental average release amount Ma is greater while the height of the leak hole from the ground is smaller, which indicates that the smaller the distance from the leak orifice to the ground, the greater the influence of the empirical discharge coefficient C₀ on the release amount M.

In order to master the structure state of subway shield tunnel, reduce the diseases and avoid the potential safety hazards, the lateral convergence deformation of subway shield tunnels should be predicted. For the non-stationarity small sample size of subway shield tunnel lateral convergence deformation value, the existing prediction models have poor performance in terms of accuracy and stability. In this paper, a lateral convergence model of subway shield tunnel based on Kalman algorithm is constructed based on Kalman filtering theory. The model is efficient, adaptive and robust, and can accurately predict the lateral convergence deformation of subway shield tunnel. Taking the horizontal diameter of 200 rings shield segment in the interval section of a subway tunnel as an example, it is proved that the residuals of the Kalman prediction model are small, the residual distribution conforms to the normal distribution, and the prediction effect is great. The model is suitable for the prediction of more than 5 periods of data, and the prediction accuracy of the model is improved with the increase of the number of data periods. In addition, the Kalman model is compared with GM(1,1) model and GM-Markov model, and RMSE and MAPE are introduced as evaluation indexes. The results show that the Kalman model has higher prediction accuracy and is more suitable for predicting the lateral convergence deformation of subway shield tunnel.

Extracellular vesicles (EVs), such as exosomes or oncosomes are released with molecules unfavorable for survival from cells. In addition, accumulating evidence has shown that tumor cells often eject anti-cancer drugs such as chemotherapeutics and targeted drugs within EVs, a novel mechanism of drug resistance. The EV-releasing, drug resistance phenotype is often coupled with cellular dedifferentiation and transformation, cells undergoing epithelial-mesenchymal transition (EMT) and taking on a cancer stem cell phenotype. Recent studies have shown that the release of EVs is also involved in immunosuppression. The concept of the resistance-associated secretory phenotype (RASP) is reviewed herein.

A series of water diversion projects to address the uneven distribution of water resources in China involve the construction of a large number of hydraulic tunnels. As the lining structure that maintains the stability and durability of the tunnels, it is prone to durability damage during the operation process, which in turn affects the water transmission safety and water supply capacity. Therefore, it is important to evaluate the durability of hydraulic tunnel lining structure. Considering the randomness and fuzziness of the factors affecting the durability of hydraulic tunnel lining structure, this paper proposes a comprehensive evaluation model based on the coupling of set-pair analysis and extension. The G1 method and the simple correlation function method are used to determine the subjective and objective weights of the evaluation indexes respectively, and the combination weight is assigned based on the principle of minimum entropy; the set-pair analysis principle is used to establish the linkage affiliation function, calculate the comprehensive linkage affiliation of the object to be evaluated, and the maximum affiliation principle is used to judge the durability level of the hydraulic tunnel lining structure. Finally, taking a section of hydraulic tunnel as an example, the model proposed in this paper is used to calculate its durability grade as Class III, with the set-pair potential SHI(H) = 7.5856, which is consistent with the actual engineering practice, and a comparative study is done in combination with the AHP-Extenics method. It is verified that the evaluation model can scientifically and reasonably evaluate the durability of hydraulic tunnel lining structure, providing a basis for subsequent maintenance and reinforcement.

This study evaluated the impact of rough, smooth, and very smooth Titanium (Ti) and zirconia (Zr) surfaces on the neutrophil expression of elastase (NE), matrix metalloproteinase (MMP)-8, MMP-9 and extracellular traps (NETs). Ti and Zr disks with a diameter of 10mm and a thickness of 1.5mm were processed using diamond-impregnated polishing burs and paste to generate rough (R; Ra= > 3µm), smooth (S; Ra= ≥1 to 1.5µm) and very smooth (VS; Ra= <0.1µm) surfaces. Peripheral neutrophils from Wistar rats were cultured on these surfaces and the culture supernatants subsequently analyzed for the presence of NE, MMP-8, and MMP-9 by ELISA, while NETs formation was demonstrated immunohistochemically by staining neutrophils with CD16b and DNA with DAPI. Overall, the expression of NE and MMP-8 were significantly higher from neutrophils cultured on both on Ti and Zr rough surfaces compared to the very smooth surface (R>S>VS) after 2h and 4h of culture. The expression of MMP-9 also increased with culture time however no significant surface effects on expression were observed. Similarly, rough Ti and Zr surfaces (R & S) also showed significantly larger NETs formation compared to the very smooth surface (VS) after 4h and 8h culture. Our findings suggest that increasing surface roughness on Ti and Zr triggers higher secretion of NE, MMP-8 and NETs formation.

Differences in the physical and chemical properties of reclaimed water (RW) and natural surface water (SW) lead to the differences in terms of nitrogen and phosphorus release when pipeline sediments enter these water bodies. The nitrogen and phosphorus release kinetics from pipe sediments with different particle sizes have been investigated. The results demonstrated that both SW and RW had a pH buffering effect after sediment addition, and the final pH (approximately 8.1) of RW was lower. The release of total phosphorus (TP) and ammonia nitrogen ( NH₄⁺-N) fitted the first-order kinetic model where the release of TP reached equilibrium; TP release was inhibited in both SW and RW, where RW exhibited the lowest (by a factor of 1.23~2.44) release (0.002 mg/g). The release of NH4+-N was promoted in both SW and RW; the maximum release in RW was 0.0188 mg/g. The amounts of NH₄⁺-N released in SW and RW were 1.02-1.40 and 1.30-1.80 times that of the control group (CG), respectively. The percentage of TP and NH₄⁺-N release in the three groups was highest in 75-154 μm pipe sediment, reaching 34.53% and 43.51% in SW and RW, respectively. These results can assist in the development of water quality evolution models for specific urban scenarios, and provide important guidance for the precise regulation of recharge water quality during and after rainfall.

This paper presents the results of hot smoke tests, conducted in a real road tunnel. The tunnel is located within the expressway S69 in southern Poland between cities Żywiec and Zwardoń. Its common name is Laliki tunnel. It is a bi-directional non-urban tunnel. The length of the tunnel is 678 m and it is inclined by 4%. It is equipped with the longitudinal ventilation system. Two hot smoke tests have been carried out according to Australian Standard AS 4391-1999. Hot smoke tests corresponded to a HRR (Heat Release Rate) equal to respectively 750 kW and 1500 kW. The fire source was located in the middle of the road lane imitating an initial phase of a car fire (respectively 150 m and 265 m from S portal). The temperature distribution was recorded during both tests using a set of fourteen thermocouples mounted at two stand poles located at the main axis of the tunnel on windward. The stand poles were placed at distances of 5 m and 10 m. The recorded data were applied to validate of a numerical model built and solved using Ansys Fluent. The calculated temperature distribution matched the measured values.

Severe cancer pain significantly diminishes patients' quality of life, leading to increased reliance on caregivers. Although opioid analgesics are effective, they may induce opioid-induced bowel dysfunction (OIBD) with symptoms such as nausea, vomiting, drowsiness, and constipation. While controlled-release oxycodone is a viable option, its prolonged use can lead to opi-oid-induced constipation (OIC). Addressing this, a relative novel formulation - a fixed 2:1 ratio of oxycodone and naloxone in prolonged release - aims to provide analgesia while alleviating OIC. This review critically assesses the evidence on the efficacy, safety, and patient experience of ox-ycodone/naloxone prolonged release in managing severe cancer pain, emphasizing the necessity for a targeted approach in this patient population.

High-precision dynamic positioning of highway vehicles is the foundation and prerequisite for achieving intelligent connected transportation. For the shortcomings of GNSS/INS combination and GNSS/INS/OD combination in tunnel vehicle positioning, this paper proposes a tunnel vehi-cle positioning method of GNSS/INS/OD combination based on lateral distance measurement and lane constraint. Firstly, lateral distance measurement of vehicles inside the tunnel is conducted based on laser radar point cloud data. Secondly, map matching positioning is performed based on lateral distance measurement, odometer, and lane markings. Experimental results demonstrate that for a 4.6 km tunnel, the average absolute error of lateral positioning is 0.294 meters, and the longitudinal positioning error is no more than 0.6 meters, which can effectively meet practical operational requirements.

Drafting formations have been long recognized as highly effective for reducing drag and enhancing athletic performance, particularly in race walking events. The precise spacing and positioning of the race walkers are critical to optimizing the effectiveness of drafting. In this study, the drag reduction of 15 drafting formations is investigated using wind-tunnel experiments and CFD numerical simulations. The results show excellent consistency in drag reduction rate between the two methods, with differences being within 10%. This can be attributed to spacing replacing body shape differences as the primary factor influencing drag reduction. Optimal double, triple, and quadruple drafting formations produce the same results in both wind-tunnel experiments and CFD simulation, resulting in drag reductions of 67%, 66%, and 81% (wind-tunnel) and 65%, 72%, and 85% (CFD). The sources of drag differences in the two methods are discussed from various aspects. The flow field obtained through CFD analysis is used to examine the mechanism of drag reduction, revealing that drafting formations have a significant shielding effect on incoming air, which reduces the number and speed of airflow impacting the core race walker. This shielding effect is identified as the primary cause of drag reduction. Using an empirical model for mechanical power output, optimal double, triple, and quadruple drafting formations enhance sport economy (4.4-5.7%), speed (3.61-4.67%), and performance (173.8-223.3s) compared to race walking alone. The findings can serve as a reference for race walkers' positioning strategy and provide insights for considering drafting formations in various running events.

Sudden variation of aerodynamic loads is the potential source of safety accidents of high-speed train (HST). As a follow-up investigation on the aerodynamic response of a HST that enters a tunnel under crosswind environment, this paper focuses on the transient response of a HST’s safety indices based on the train–track coupling interaction model. Firstly, a wind–train–track coupling dynamic model is proposed by introducing transient aerodynamic loads into the vehicle–track system. Secondly, the temporal evolution of safety coefficients indicates that the train’s safety risk increases during tunnel entry with crosswind. Results show that the derailment coefficients and wheel load reduction rate during tunnel entry are not only larger than those in open air but also those inside the tunnel due to the sudden disappearance of wind excitation at the tunnel entrance. In addition, the characteristic wind curve, which is the wind velocity against the train speed, is presented for application based on the current specification of the safety criteria threshold. The investigation will be useful in assessing the safety risk of a running train subjected to other aerodynamic attacks, such as the coupling effect of infrastructure scenario and crosswind in windy area.

A visual study of spiral galaxies from a subset of spiral galaxies in the Dark Energy Survey Data Release 2 finds that a significant number show long tails of baryonic matter, often much longer than the apparent diameter of the galaxy. Examples from less than 10% of the candidates are shown here and their possible origin is discussed. The tails were only seen connected to spiral galaxies; no examples of tails connected to elliptical galaxies or to artifacts were found. In many examples the tail is associated with what appears to be a colliding galaxy, but in many others there is no sign of one. An intriguing possibility is that in the latter cases the tails are produced by an encounter with an unseen object, either a massive black hole or a compact galaxy with mostly dark matter.

Severe disease and uremia are risk factors for neurological complications of coronavirus disease-2019 (COVID-19). An in-depth analysis of a case series was conducted to describe the neurological manifestations of patients with COVID-19 and gain pathophysiological insights that may guide clinical decision-making – especially with respect to the cytokine release syndrome (CRS). Extensive clinical, laboratory, and imaging phenotyping was performed in five patients. Neurological presentation included confusion, tremor, cerebellar ataxia, behavioral alterations, aphasia, pyramidal syndrome, coma, cranial nerve palsy, dysautonomia, and central hypothyroidism. Neurological disturbances were remarkably accompanied by laboratory evidence of CRS. SARS-CoV-2 was undetectable in the cerebrospinal fluid. Hyperalbuminorachy and increased levels of the astroglial protein S100B were suggestive of blood-brain barrier (BBB) dysfunction. Brain MRI findings comprised evidence of acute leukoencephalitis (n = 3, of whom one with a hemorrhagic form), cytotoxic edema mimicking ischemic stroke (n = 1), or normal results (n = 2). Treatment with corticosteroids and/or intravenous immunoglobulins was attempted – resulting in rapid recovery from neurological disturbances in two cases. Patients with COVID-19 can develop neurological manifestations that share clinical, laboratory, and imaging similarities with those of chimeric antigen receptor-T cell-related encephalopathy. The pathophysiological underpinnings appear to involve CRS, endothelial activation, BBB dysfunction, and immune-mediated mechanisms.

Perception of flavor is a dynamic process during which the concentration of aroma molecules at the olfactory epithelium varies with time as they are released progressively from the food in the mouth during consumption. The release kinetics depends on the food matrix itself, but also on food oral processing, such as mastication behavior and food bolus formation with saliva, for which huge inter-individual variations exist due to physiological differences. Sensory methods, such as time-intensity (TI), or the more recent methods temporal dominance of sensations (TDS) and temporal check-all-that-apply (TCATA), are used to account for the dynamic and time-related aspects of flavor perception. Direct injection mass spectrometry (DIMS) techniques that measure in real-time aroma compounds directly in the nose (nosespace), aimed at obtaining data that reflect the pattern of aroma release in real-time during food consumption, supposed to be representative of perception, have been developed since 25 years. Examples obtained with MS operated in chemical ionization mode at atmospheric or sub-atmospheric pressure (atmospheric pressure chemical ionization APCI or proton transfer reaction PTR) will be given, with emphases on studies conducted with simultaneous dynamic sensory evaluation. Inter-individual variations in terms of aroma release and their relevance for understanding flavor perception will be discussed, as well as evidenced cross-modal interactions.

In the present study the synthesis of gold nanoparticles (AuNPs) loaded with methotrexate (MTX) has been carried out in order to obtain controlled size and monodispersed nanocarriers, around 20nm. Characterization study shows metallic AuNPs with MTX polydispersed on the surface. MTX is linked by a replacement of citrate by the MTX carboxyl group. The drug release profiles showed faster MTX release when it is conjugated, which leads to the best control of plasma concentration. Also, the enhanced release observed at pH 5 could take advantage of the pH gradients that exist in tumor microenvironments to achieve high local drug concentrations. AuNPs-MTX conjugates were tested by flow cytometry against lung (A-549) and colon (HTC-116) cancer cell lines. Results for A-549 showed a lighter dose-response effect than for colon cancer ones. This could be related to the presence of folate receptors in line HTC-116 on the contrary than line A-549, supporting the specific uptake of folate-conjugated AuNPs-MTX by folate receptor positive tumor cells. Conjugates exhibited considerably higher cytotoxic effects compared with the effects of equal doses of free MTX. Anexin V-PI test sustain as cell death mechanism apoptosis, which is normally disabled in cancer cells.

Tumor cells exhibit a resistance-associated secretory phenotype involving extracellular vesicles (EVs) and heat shock proteins (HSPs). This response occurs in response to cell stress and cancer therapeutics. HSPs are stress-responsive molecular chaperones promoting proper protein folding, while also being released from cells with EVs as well as in free form as alarmins. We have here investigated the secretory phenotype of castration-resistant prostate cancer (CRPC) cells using proteome analysis. We have also examined the roles of the key co-chaperone CDC37 in stressome release, epithelial-to-mesenchymal transition (EMT), and tumor progression. A number of HSP family members and their common receptor CD91/LRP1 were enriched at high levels in CRPC cell-derived EVs among over 700 other protein species. The small EVs (30 to 200 nm in size, potentially exosomes) were released even in a non-heated condition from the prostate cancer cells, whereas EMT-coupled release of EVs (200 to 500 nm, likely ectosomes) with associated HSP90α was increased after heat shock stress (HSS). Lactate dehydrogenase, a marker of membrane leakage/damage of cells, was also released upon HSS from the prostate cancer cells. During this stress response, intracellular CDC37 was also transcriptionally inducible by heat shock factor 1, and knockdown of CDC37 decreased EMT-coupled release of EVs. Triple knockdown of CDC37, HSP90α, and HSP90β was required for efficient reduction of the chaperone trio and to reduce tumorigenicity of the CRPC cells in vivo. Taken together, the data indicated that CDC37 and HSP90 are essential for stressome release and for tumorigenesis in resistant cancer.

Using polymethylmethacrylate (PMMA) bone cement is widespread in orthopedic surgeries for implant fixation and as a carrier for antibiotic delivery to prevent and treat infections. This review comprehensively evaluates in vitro studies investigating the antibiotic elution profiles and mechanical properties of PMMA bone cement. We explore the kinetics of antibiotic release, factors influencing elution efficiency, and the impact of various antibiotics on the mechanical properties of PMMA composites. At the same time, we examine how the inclusion of antibiotics affects the mechanical integrity of PMMA, including parameters such as compressive strength, tensile strength, and fatigue resistance. Through a detailed analysis of these studies, this review aims to provide insights into optimizing PMMA bone cement formulations for enhanced therapeutic efficacy and structural performance.

The cycling of soil phosphorus (P) is inherently linked with soil organic carbon-iron (C-Fe) cycling, yet empirical integration of these processes within paddy soils remains scarce. In this study, we conducted a microcosm experiment using paddy soils subjected to six distinct fertilization regimes involving varying P inputs for five years. In addition to evaluating P activation under reflooding conditions, we assessed the Fe reduction process and characterized the properties of dissolved organic matter (DOM) at the molecular level using Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS), alongside profiling the composition of soil microbial communities with high-throughput sequencing. Our findings revealed that after 25 days of reflooding, soil Olsen-P content increased by an average of 73% compared to its initial state, showing a strong correlation with the Fe reduction process. Specifically, treatments involving pig manure application exhibited higher Fe reduction rates and enhanced P activation, highlighting the role of organic matter in facilitating Fe reduction. Investigations on the relative abundance of typical iron-reducing microbes further supported their importance in P activation, but the rate of iron reduction is limited by soil organic matter content. Delving deeper into DOM properties, soil DOM composition profiling and network analysis suggested that high-molecular-weight DOM, particularly lignins, served as the primary resources driving Fe reduction by iron-reducing microbes, consequently promoting Fe reduction and P release. Taken together, our study assembled the C-Fe-P cycling dynamics in paddy soils, emphasizing the pivotal role of microbial-driven Fe reduction facilitated by soil DOM in P availability and subsequently sustainable agricultural practices.

In this study, we focus on the effects of fuel bed representation and fire heat and smoke distribution in a coupled fire-atmosphere simulation platform for two landscape-scale fires: the 2018 Camp Fire and the 2021 Caldor Fire. The fuel bed representation in the coupled fire-atmosphere simulation platform WRF-Fire currently includes only surface fuels. Thus, we enhance the model by adding canopy fuel characteristics and heat release, for which a method to calculate the heat generated from canopy fuel consumption is developed and implemented in WRF-Fire. Furthermore, the current WRF-Fire heat and smoke distribution in the atmosphere is replaced with a heat-conserving Truncated Gaussian (TG) function and its effects are evaluated. The simulated fire perimeters of case studies are validated against semi-continuous, high-resolution fire perimeters derived from NEXRAD radar observations. Furthermore, simulated plumes of the two fire cases are compared to NEXRAD radar reflectivity observations followed by buoyancy analysis using simulated temperature and vertical velocity fields. The results show that while the improved fuel bed and the TG heat release scheme have small effects on the simulated fire perimeters of the wind-driven Camp Fire, they affect the propagation direction of the plume-driven Caldor Fire, leading to better-matching fire perimeters with the observations. However, the improved fuel bed representation together with the TG heat smoke release scheme leads to more realistic plume structure in comparison to the observations in both fires. The buoyancy analysis also depicts more realistic fire-induced temperature anomalies and atmospheric circulation when the fuel bed is improved.

We consider the problem of scheduling $n$ jobs with identical processing times and given release as well as delivery times on $m$ uniform machines. The goal is to minimize the makespan, i.e., the maximum full completion time of any job. This problem is well-known to have an open complexity status even if the number of jobs is fixed. We present a polynomial-time algorithm for the problem which is based on the earlier introduced algorithmic framework blesscmore (``branch less and cut more''). We extend the analysis of the so-called behavior alternatives developed earlier for the version of the problem with identical parallel machines and show how the earlier used technique for identical machines can be extended to the uniform machine environment if a special condition on the job parameters is imposed. The time complexity of the proposed algorithm is $O(\gamma m^2 n\log n)$, where $\gamma$ can be either $n$ or the maximum job delivery time $q_{\max}$. This complexity can even be reduced further by using a smaller number $\kappa<n$ in the estimation describing the number of jobs of particular types. However, this number $\kappa$ becomes only known when the algorithm has terminated.

With more and more transportation tunnels have been and will be constructed in loess areas in Northwest China with high earthquake potential, the overall stability of portal section under earthquakes actions and the related aseismic countermeasures attracted the attentions from both the scholars and engineers, especially the tunnels in the upper slope connecting the high bridges crossing rivers or valleys. In order to study the dynamic response characteristics and damage evolution of steep loess slope with a tunnel under the earthquake actions, a large-scale shaking table tests were performed on steep loess slope with a tunnel. Wenchuan-tangyu (WT) wave and El Centro (El) wave records were applied on the model to investigate the displacement response and acceleration response of loess slope with a tunnel under the horizontal (X) and the combined action of horizontal and vertical (X-Z) seismic loads, respectively. In particular, three-dimensional non-contact optical measurement techniques were used to obtain the slope surface displacements. The results showed that the main deformation pattern of the slope was horizontal movement and settlement when the seismic wave input was in the X and X-Z directions, respectively. However, the X direction seismic wave had a greater impact on the deformation of the slope, and the tunnel portal slope was destroyed under the action of a large horizontal seismic acceleration finally. Slope failure ahead of a tunnel could be divided into four stages, i.e. elastic deformation stage, plastic deformation accumulation stage, local failure stage, and overall failure stage. The peak ground displacement of X direction (PGDX) and peak ground displacement of Z direction (PGDZ) of the slope surface increased with the increasing of the input peak ground acceleration (PGA) when the input wave was same waveform and same direction. The existence of the tunnel had a great influence on the PGA and the PGA amplification factor (PGAAF) of the soil mass surrounding it. This was because the seismic waves encounter a tunnel surface with clear differences in the physical properties of the medium during their propagation in the slope, thereby forming a strong reflection and refraction effect, and the amplitude changed significantly. Numerical simulation results were basically consistent with the experimental results.

Tarsal tunnel syndrome is a focal compressive neuropathy of the posterior tibial nerve or one of its associated branches. Brief mention is made in the literature of the use of corticosteroid injections for this condition. The basic technique of hydrodissection is used for other nerve entrapments and includes identifying the region of nerve compression, and the injection of a fluid medium to dissect between structures or fascial planes. We introduce our treatment protocol using a methylprednisolone/sterile water/ropivacaine hydrochloride injectate mix and peripheral nerve stimulation to a perform hydrodissection technique for tarsal tunnel syndrome.

Based on the kinematic approach of the limit analysis and slip-line theories, this paper proposes a new 2D analytical model to evaluate the collapse support pressure to ensure the face stability of a circular tunnel in purely cohesive soils driven by a shield. The normality conditions, the yield criterion and the vertical soil arching effect are considered in the analytical model. Two upper bound solutions corresponding to the ratio of the cover to the diameter (C/D) are derived from considering the mechanisms based on the motion of rigid multi-blocks. Comparisons are made with existing upper and lower bound solutions published in previous articles. The results are close to the solutions of practical engineering. The failure mechanisms proposed in this study provide a better explanation for the failure process in the heading of the tunnel face.

This study develops a vitamin C controlled-release system trackable via color changes as a function of vitamin C release. The system is composed of coaxial microfibers prepared via coaxial electrospinning, with a core of poly(ethylene oxide) (PEO) incorporating vitamin C, and a shell composed of polycaprolactone (PCL) containing polydiacetylene (PDA) as the color-changing material. The shell thickness was controlled by adjusting the amount of PCL ejected during electrospinning, allowing the regulation of the release rate of vitamin C. When vitamin C added to PEO penetrated the PCL layer, the color of PDA changed from blue to red, indicating a color change. The results of this study can be applied to devices that require immediate detection of vitamin C release levels.

The influence of lignin modification on drug release and pH-dependent releasing behaviour of oral solid dosage form was investigated using three different formulations. The first formulation contains microcrystalline cellulose (MCC101) as excipient and paracetamol as active pharmaceutical ingredient (API). The second formulation includes Alcell lignin and MCC 101 as excipient and paracetamol, and the third formulation consists of carboxylated Alcell lignin, MCC 101 and paracetamol. Direct compaction was carried out in order to prepare the tablets. Lignin can be readily chemically modified due to the existence of different functional groups in its structure. The focus of this investigation is on lignin carboxylation and its influence on paracetamol control release behaviour at varying pH. Results suggest that carboxylated lignin tablets had the highest drug release, which is linked to their faster disintegration and lower tablet hardness.

Currently the bimatoprost implant (DURYSTA) is approved for a single administration secondary to concern for progressive corneal endothelial cell (CEC) loss with intracameral administration. In order to better understand the cause of CEC loss and other adverse events (AEs) with intracameral administration, multimodal imaging of the implant utilizing optical coherence topography (OCT), robotic ultrasound and bio microscopy video recording was utilized. Inherently the anterior chamber is a non-confined space. In certain examples the implant assumed a round and spotted structure as it picked up iris pigment as it migrated around the anterior chamber. Accordingly, we explored delivery of the implant in the middle segment behind the iris and in front of the pseudophakic lens. We then evaluated the suitability of various imaging modalities to assess the implant in this location. For middle segment administration, the ArcScan Insight 100 robotic ultrasound provided resolution and repeatability sufficient to monitor the implant behind the iris. This preliminary study hypothesizes that DURYSTA migration in the anterior chamber is the main source of AEs. Through use of a confined location, the middle segment, the implant is unlikely to migrate and cause CEC loss while also delivering drug closer to its site of action, the ciliary body. Further efforts are underway to understand the suitability of the middle segment for serial DURYSTA administration to maximize intraocular pressure lowering while minimizing AEs.

In this work, we designed and fabricated a multifunctional nanocomposite system which consists of chitosan, raspberry-like silver nanoparticles and graphene oxide. Room temperature atmospheric pressure microplasma (RT-APM) process provides a rapid, facile, and environment-friendly method for introducing silver nanoparticles into the composite system. By loading different drugs onto the polymer matrix and/or graphene oxide, our composite can achieve a pH controlled dual drug release with release profile specific to the drugs used. In addition to its strong antibacterial ability against E. coli and S. aureus, our composite also demonstrates excellent photothermal conversion effect under irradiation of near infrared lasers. These unique functionalities point to it’s the potential of nanocomposite system in multiple applications areas such as multimodal therapeutics in healthcare, water treatment, and anti-microbial, etc.

Blood Concentrates (BCs) are autologous non-transfusional therapeutical preparations with biological properties applied in tissue regeneration. These BCs differ in the preparation method, in fibrin network architecture, growth factors release as well as in platelet/cell content. Methodological changes result in distinct matrices that can compromise their clinical effectiveness. The present study evaluated the influence of different g-forces and types of tubes in the release of vascular endothelial growth factor (VEGF) from platelet-rich fibrin (PRF) as a function of time. The PRF-like samples were obtained with three g-forces (200, 400, and 800 x g) for 10 minutes in pure glass tubes or in polystyrene-clot activator tubes. Scanning and Transmission electron microscopy was used to morphometric analyzes of PRF’s specimens and flow cytometry was used to quantify VEGF slow release until 7 days. Our results showed that platelets were intact and adhered to the fibrin network, emitting pseudopods and in degranulation. The fibrin network was rough and twisted with exosomic granulations impregnated on its surface. An increase in the concentration of VEGF in the PRF supernatant was observed until 7 days for all g forces (200, 400 or 800 x g), with the highest concentrations observed with 200 x g, in both tubes, glass or plastic. Morphological analyzes showed a reduction in the diameter of the PRF fibers after 7 days. Our results showed that g-force interferes with the shape of the fibrin network in the PRF, as well as affect the release of VEGF stored into platelets. This finding may be useful in applying PRF to skin lesions, in which the rapid release of growth factors can favor the tissue repair process. Our observations point to a greater clarification on the methodological variations related to obtaining PRF matrices, as they can generate products with different characteristics and degrees of effectiveness in specific applications.

In the context of the Korean building structure standard KDS2022, wind loads can be readily calculated in terms of the along-wind, across-wind, and torsional components, based on a single wind direction. However, this approach falls short in accurately and safely evaluating the impact of winds from various directions. Therefore, in this study, we developed a Wind Load Calculation Program (WCP) capable of predicting wind loads with relative precision during the preliminary design phase. First, wind tunnel tests were conducted to identify the essential factors necessary for calculating wind loads and the variables influencing these factors. The building shape considered was a square, and the wind force coefficients and power spectral density were measured by combining 4 ground roughness values, 11 side ratios (), 4 aspect ratios (), and wind directions ranging from 0° to 90°. Subsequently, a generalized formulation was devised to facilitate wind load calculations across diverse conditions and a method for calculating load combination coefficients, considering response correlation and load simultaneity, was presented. Finally, the wind loads obtained from the wind tunnel tests were compared with those predicted by the WCP using an actual project model.

Recently L-shaped tunneling field-effect-transistor (LTFET) has been introduced to overcome the thermal subthreshold limit of conventional metal-oxide-semiconductor field-effect-transistors (MOSFET). In this work, shortcoming of LTFET was investigated. It was found that corner effect present in LTFET effectively degrades its subthreshold slope. To get rid of corner effect a new type of device with dual material gates is presented. The new device termed as DG-LTFET gets rid of the corner effect and results in a significantly improved subthreshold slope of less than 10 mV/dec, and an improved ON/OFF current ratio over LTFET. In this work DG-LTFET was evaluated for different device parameters, and bench-marked against LTFET. This work presents an optimum configuration of DG-LTFET in terms of device dimensions and doping levels, to get the best subthreshold, ON current and ambipolar performance from the DG-LTFET.

There is a need for alternatives or complements to synthetic fertilizers to enhance agricultural sustainability. Applying organic amendments can play a significant role in this. Insect droppings show high potential, though studies evaluating their agronomic value have only recently begun to emerge. This study compared black soldier fly (Hermetia illucens) and mealworm (Tenebrio molitor) larvae frass with another organic amendment (Nutrimais) derived from composting forestry, agro-industrial, and domestic waste. The experiment also included ammonium nitrate at two rates [the same as the organic amendments, 50 kg ha–1 nitrogen (N) (FullR), and half that rate (HalfR)] and an unfertilized control. The study spanned two growth cycles of lettuce (Lactuca sativa L.) grown in pots, followed by unfertilized oats (Avena sativa L.) to assess the residual effects of the fertilizing treatments. Mealworm larvae frass mineralized rapidly, with an apparent N recovery of 37.4% over the two lettuce growth cycles, indicating its high availability to soil heterotrophic microorganisms. The average dry matter yield (DMY) of lettuce was the highest among all treatments (12.8 and 9.8 g plant–1 in the first and second lettuce cycles), even compared to the FullR treatment (12.2 and 7.8 g plant–1), though without significant differences. Although mealworm larvae frass exhibited a high mineralization rate, the DMY cannot be attributed solely to N supply, as plants in the FullR treatment showed better N nutritional status. Mealworm larvae frass provided strong evidence of a plant biostimulant effect, not explained by the variables measured in this study. Black soldier fly larvae frass exhibited typical behavior of a moderately reactive organic amendment, while Nutrimais showed low reactivity, with a near-neutral mineralization/immobilization balance. The results suggest mealworm larvae frass is recommended for early maturing vegetable crops, whereas Nutrimais appears more suitable for perennial crops with low short-term nutrient requirements.

The evolution of release factors catalyzing the hydrolysis of the final peptidyl-tRNA bond and the release of the polypeptide from the ribosome has been a longstanding paradox. While the components of the translation apparatus are generally well-conserved across extant life, structurally-unrelated release factor peptidyl hydrolases (RF-PHs) emerged in the stems of the bacterial and archaeo-eukaryotic lineages. We analyze the diversification of RF-PH domains within the broader evolutionary framework of the translation apparatus. Thus, we reconstruct the possible state of translation termination in the Last Universal Common Ancestor with possible tRNA-like terminators. Further, evolutionary trajectories of the several auxiliary release factors in ribosome quality control (RQC) and rescue pathways point to multiple independent solutions to this problem and frequent transfers between superkingdoms including the recently-characterized ArfT, which is more widely-distributed across life than previously appreciated. The eukaryotic RQC system was pieced together from components with disparate provenance, which include the long-sought Vms1/ANKZF1 RF-PH of bacterial origin. We also uncover an under-appreciated evolutionary driver of innovation in rescue pathways: effectors deployed in biological conflicts that target the ribosome. At least three rescue pathways (centered on the prfH/RFH, baeRF-1, and C12orf65 RF-PH domains), were likely innovated in response to such conflicts.

Neuronal timing is critical for many brain functions such as perception and learning. At the level of the chemical synapse, the synaptic delay is determined by the presynaptic release probability (Pr) and the waveform of the presynaptic action potential (AP). Depolarization-induced analogue-digital facilitation (d-ADF) is a form of context-dependent synaptic facilitation that is induced by constant depolarization of the presynaptic neuron and is mediated by voltage inactivation of presynaptic Kv1 channels. Whether synaptic delay is modulated during d-ADF remains unclear. We show here that despite Pr is elevated during d-ADF at L5-L5 synapses, the synaptic delay is surprisingly unchanged, suggesting that both Pr- and AP-dependent changes in synaptic delay compensate for each other. We conclude that in contrast with other short- or long-term modulation of presynaptic release, timing is not affected during d-ADF because of the opposite interaction of Pr- and AP-dependent modulations of synaptic delay.

Ferroptosis is an iron-dependent cell death pathway that involves depletion of intracellular glutathione (GSH) levels and iron-mediated lipid peroxidation. Ferroptosis is experimentally caused by inhibition of the cystine/glutamate antiporter xCT, which depletes cells of GSH, or by inhibition of Glutathione peroxidase 4 (GPx4), a key regulator of lipid peroxidation. The events that occur between GPx4 inhibition and the execution of ferroptotic cell death are currently a matter of active research. Previous work has shown that calcium release from the endoplasmic reticulum (ER) mediated by ryanodine receptor (RyR) channels contributes to ferroptosis-induced cell death in primary hippocampal neurons. Here, we used SH-SY5Y neuroblastoma cells, which do not express RyR channels, to test if calcium release mediated by the inositol 1,4,5-trisphosphate receptor (IP3R) channel plays a role in this process. We show that inhibition of GPx4 by RAS Selective Lethal Compound 3 (RSL3) generated an increase in reactive oxygen species (ROS), increased cytoplasmic and mitochondrial calcium levels, increased lipid peroxidation and caused cell death. The RSL3-induced calcium signals were inhibited by Xestospongin B, an inhibitor of the ER-resident IP3R calcium channel, by decreasing IP3R levels with carbachol and by IP3R1 knock-down. The intracellular calcium chelator BAPTA-AM inhibited RSL3-induced calcium signals, which were not affected by extracellular calcium depletion. We propose that GPx4 inhibition activates IP3R-mediated calcium release in SH-SY5Y cells, leading to increased cytoplasmic and mitochondrial calcium levels, which in turn stimulate the production of ROS and induce lipid peroxidation and ferroptotic cell death in a noxious positive feedback cycle.

This work deals with the synthesis of bare and curcumin (CUR)-loaded chitosan (CS)-based macroparticles by ionic gelation using sodium hydroxide (NaOH) or sodium tripolyphosphate (TPP) as cross-linking agents. The resulting spherical-shaped macroparticles were studied using various characterization techniques, Scanning Electron Microscopy (SEM), Fourier Transformed Infrared Spectroscopy (FTIR), Thermogravimetric Analysis (TGA), and Differential Scanning Calorimetry (DSC). The release of CUR from the CS-based particles with respect to time was analyzed, and the encapsulation efficiency and degree of swelling were studied. All formulations showed excellent CUR trapping efficiency, exceeding 90%. In particular, the TPP-crosslinked macrobeads released 34 wt% of the charged CUR within minutes, while the remaining 66 wt% was released slowly due to the biodegradation of CS. The results indicate that the correct choice of gelling agent and its concentration leads to spherical particles capable of encapsulating CUR and releasing it in a wide range of kinetics depending on the specific application.

Prospects for predicting the fragmentation of polypeptide chains during their enzymatic hydrolysis using proteolysis models are considered. The opening of the protein substrate during proteolysis and the exposure of its internal peptide bonds for a successful enzymatic attack, the so-called demasking process, were taken into account. The two-step model of proteolysis was used, including the parameters of peptide bond demasking and hydrolysis rate constants for various peptide bonds. Herein, we presented an algorithm for calculating the concentrations of peptide fragments depending on the hydrolysis time or the degree of hydrolysis. The intermediate peptide fragments with two or one internal specific bonds were considered. The fragmentation of β-lactoglobulin (b-LG) with trypsin was predicted, and the calculated concentration curves for peptide fragments were compared with the experimental dependences of concentrations on the degree of hydrolysis. Numerical parameters characterizing the kinetic curves were proposed for the intermediate and final peptide fragments, and they were used to compare the calculated and experimental dependences. The predicted distribution of peptide fragments corresponded to the experimental data on the peptide release during proteolysis of b-LG by trypsin.

A sustainable matrix based on eucalyptol essential oil/sawdust was developed and applied on one-sided laminated plywood. This finish aims to serve as a eucalyptol odor slow release. Eucalyptol odor release was monitored with gas chromatography coupled with a flame ionization detector (GC – FID: Limits of Detection and Quantification of 0.70 g/m3 and 2.11 g/m3, respectively, and with linearity up to 18.6 g/m3). Measurement of the eucalyptol odor released was performed during a six-month period and it was found that the release followed a first-order exponential decay with a decay rate constant of 0.0169 per day. The half-life was determined to be of 48 days. The granulometry and particle size porosity of sawdust were analyzed by Scanning Electron Microscopy. Sawdust size fraction between 112 – 200 μm showed best eucalyptol absorption capacity with 1:3 masses ratio (sawdust:eucalyptol). The time capacity of eucalyptol release depends of composite eucalyptol – sawdust quantity. Where this relation was determined: 15.0 grams of composite eucalyptol-sawdust by 0.8 mm diameter aperture gave 6 months of eucalyptol release, that was considered very positive, understanding high volatility of eucalyptol and a small quantity of composite for further products. The new product is characterized by a carbon footprint (considering the industry frontiers) of 5.94 kg CO2eq/m2 of plywood floor.

Objectives: In December 2019 a novel human-infecting coronavirus, SARS-CoV-2, has emerged. The WHO has stated the epidemic as a “public health emergency of international concern”. A drammatic situation has emerged with thousands of deaths, occurring mainly in the aged and very ill people. Epidemiological studies suggest that immune system function is impaired in elderly individuals and these subjects often present a severe deficiency in nutrients as fatsoluble and hydrosoluble vitamins. Design: In this first part of the review about Cov2 in aged people, we searched for reviews describing the characteristics of autoimmune diseases and the available therapeutic protocols for their treatment. We sed them as a paradigm with the purpose to retrieve pathogenetic mechanisms in common among these pathological conditions and SARS-CoV-2 infection, as well as the alteration induced in immune system function by this virus, or by its homologous SARS-CoV. Results: SARS-CoV-2 infection induces an important immune system dysfunction with the development of an exhuberant proinflammatory response in the host, and with the development of a life-threatening condition defined as Cytokine Release Syndrome (CRS). This leads to the Acute Respiratory Syndrome (ARDS), mainly in the aged people. High mortality and lethality rates have been observed in the elderly subjects with CoV-2-related infection. Conclusion: These diseases may serve as a paradigm for the study of CRS emerging in the course of SARS CoV-2 infection. This review discusses about the possible activity of Vitamin A, D, E and C in restoring normal antiviral Immune System function or the potential therapeutic role of these micronutrients as a part of a multi-treatment strategy against SARS- CoV-2 infection.

Developing prolonged antigen delivery systems that mimick the long-term exposure to pathogens appears as a promising, still poorly explored approach to reach durable immunities. In this study, we have used a simple technology by which his-tagged proteins can be assembled, assisted by divalent cations, as supramolecular complexes with progressive complexity, namely protein-only nanoparticles and microparticles. Microparticles produced out of nanoparticles are biomimetics of secretory granules from the mammalian hormonal system. Upon subcutaneous administration, they slowly disintegrate, acting as an endocrine-like secretory system, and rendering the building block nanoparticles progressively bioavailable. The performance of such materials, previously validated for drug delivery in oncology, has been tested here regarding the potential for time-prolonged antigen release. This has been done by taking, as building blocks, a nanostructured version of p30, a main structural immunogen from the African swine fever virus (ASFV). By challenging the system in both mice and pigs, we have observed unusually potent pro-inflammatory activity in porcine macrophages, and long-lasting humoral and cellular responses in vivo, which might overcome the need for an adjuvant. The robustness of both innate and adaptive responses tag, for the first time, these dynamic depot materials as a novel and valuable instrument with transversal applicability in immune stimulation and vaccinology.

Background: There is a high bureaucratic and administrative burden associated with health care tasks (test requesting, visits scheduling, supporting documents provision) that has historically largely fallen on health care professionals, which is one among the factors contributing to low job satisfaction and lower productivity. Incorporating new professional roles that help to better respond to the needs of both patients and professionals can increase the quality and efficiency of service provision. Objective: To evaluate the impact of the clinical assistant’s introduction in the Sant Joan de Déu Barcelona Children’s Hospital’s pediatric oncology department, in terms of displacement of activity loads carried out by this new professional role and the consequent time freed up for physicians. Methodology: Observational and retrospective study using administrative data based on the analysis of the type of activity performed by clinical assistants and the measurement of the time freed up in favor of the physicians, based on in situ timekeeping, to approximate the potential skill mix productivity increase. Results: Since its implementation in the pediatric oncology department, clinical assistants have performed 13,553 requests (69.93% of the total), representing a total saving of 266.83 hours or 6.67 workweeks of 40 hours. They performed 74.25% of outpatient surgical requests in the oncology department, 87.5% of day hospital requests and 54.13% of total requests in the outpatient consultations area. Conclusion: The introduction of clinical assistants in the oncology department could be efficient to the extent that it displaces a good part of the bureaucratic and administrative tasks previously performed by health care professionals. This delegation allows them to work more closely to the maximum of their competences and the physicians to have more time for higher added value clinical tasks. In terms of efficiency, this role change enables to optimize the clinical process, reducing the cost by 56% compared to the conventional model.