In the drive towards environmental restoration and sustainable energy solutions, effective utilization and management of agricultural crop residues are vital to mitigate greenhouse gas (GHG) emissions and waste accumulation. Converting biogenic wastes into biofuels and bioproducts has the potential to tackle the energy crisis and contribute to environmental remediation. In this investigation, teff husk, primarily generated in Ethiopia during teff production within the agro-industrial sector, is used as the feedstock for the slow pyrolysis process. In Ethiopia, it is estimated that over 1.75 million tons of teff husk are generated annually, with a significant portion being incinerated in the fields, resulting in substantial environmental pollution. This study focuses on assessing teff husk as a potential material for slow pyrolysis, a crucial stage in biochar production, to tap into its biochar-producing potential. To determine the composition of the biomass, the teff-husk was initially analyzed by thermogravimetry. The significant presence of fixed carbon indicates that teff husk is a viable candidate for pyrolytic conversion into biochar particles. The process of slow pyrolysis took place at three varied temperatures—specifically, at 400, 450, and 500 °C. Process parameters of slow pyrolysis such as reaction time, temperature, and heating rate were enhanced to obtain maximum biochar yields. The highest biochar yield of 43.4 wt% was recorded at optimized reaction time, temperature, and heating rate of 120 min, 400 °C, and 4.2 °C/min, respectively. Furthermore, biochar's physicochemical, SEM-EDX, FTIR, and TGA characterization were performed. The thermal stability and carbon content of biochar were found to rise at higher temperatures. Unlike fuel recovery, the results suggest that teff-husk can be used as a feedstock for biochar production.

Continuity of activities and projects are important for sustainably developing organizations, especially universities. The purpose of this research study is to find university development guidelines regarding waste management according to the green university ranking criteria for sustainable developments by studying and collecting the data covering the last five years (2019 - 2023) of Mahasarakham University. We also analyzed and synthesized lessons learned from the details of the operations and the factors involved in successes while comparing and providing suggestions for the operations in the next year. It was found that waste management that resulted in continuous developments that achieved the goals of Mahasarakham University consisted of the five guidelines. (1) Making green university policies and using them as the (key performance index) KPI of the divisions and also announcing the university's waste management policies by applying the principles of 3R (Reuse-Reduce-Recycle). (2) Allocating the budgets supporting the projects' activities according to the evaluation criteria. (3) Student and personnel participation as well as the mechanisms used by the committees from various administrative divisions such as Student Council, Student Association and clubs to drive the operations. (4) Identifying the main responsible individuals and committees for the green university who communicated and drove the operations while collecting, analyzing and preparing the data. (5) Follow-ups and evaluations of the project's activities with the Plan-Do-Check-Act (PDCA) processes for continuous and sustainable developments and improvements leading to the green university. With the above operations, Mahasarakham University's waste management scores of the six indices during 2019 - 3023 increased annually as follows: 900, 900, 1050, 1275 and 1350.

The development of virtual models has recently been generalized in the field of complex mechatronic product design. Virtual models have various advantages such as: the systemic design approach, most often parametric, the implementation of extreme, expensive, and perhaps risky scenarios for the operation of the designed product, the testing of a large number of variants, etc. The main contribution of the paper consists of the development of an interface family called DeSeRoI (Dedicated Serial Robot Interface). Each member of the interface family integrates Simulink libraries and is created by the programmer in accordance with user requests. It follows that the interfaces composing the DeSeRoI family can have different levels of complexity depending on user needs and constraints. We are implementing a MATLAB-based application with user-provided configuration for serial robots in order to automatically visualize the kinematics data and simulation. Within MATLAB, two scripts are created responsible for generating Simulink models that compute the kinematics problem. One of the scripts (Main) saves information about the configuration of the robot and the other one (Generates_Simulink_Models) computes the kinematics problem. Different types of functions (software module) have been developed. Using these functions, the Simulink models result as modular entities. The automated approach eases user’s interaction and understanding of serial robots’ kinematics by performing the simulation procedure in a shorter amount of time and with higher efficiency, assuring a precise outcome despite the chosen parameters.

The article examines the relationship between household food waste and GDP in various European regions, aiming to determine how economic prosperity influences household food waste levels. Using comparative analysis of secondary and tertiary data, we developed a synthetic indicator (IpFW), to assess the interaction between GDP per capita and household food waste per capita. Despite expectations, higher GDP did not consistently correlate with lower food waste, challenging assumptions about economic prosperity and environmental stewardship. The research underscores the complex interplay between economic factors and food waste management, revealing no significant correlation even at regional levels. It also highlights the potential of e-commerce in enhancing food waste reduction strategies. E-commerce platforms can optimize food supply chains and consumer behavior, contributing to more sustainable consumption patterns. The conclusions call for a reevaluation of policies and suggest that integrating e-commerce could bolster efforts to manage food waste more effectively, aligning with the Sustainable Development Goals.

This review aims to explore the intricate relationship between epigenetic mechanisms, stress, and affective disorders, focusing on how early life experiences and coping mechanisms contribute to susceptibility to mood disorders. Epigenetic factors play a crucial role in regulating gene expression without altering the DNA (deoxyribonucleic acid) sequence, and recent research has revealed associations between epigenetic changes and maladaptive responses to stress or psychiatric disorders. A scoping review of 33 studies employing the PRISMA-S (Preferred Reporting Items for Systematic Reviews and Meta-Analyses – Statement) guidelines investigates the role of stress-induced epigenetic mechanisms and coping strategies in affective disorders' occurrence, development, and progression. The analysis encompasses various stress factors, including childhood trauma, work-related stress, and dietary deficiencies, alongside epigenetic changes such as DNA methylation and altered gene expression. Findings indicate that specific stress-related genes frequently exhibit epigenetic changes associated with affective disorders. Moreover, the review examines coping mechanisms in patients with bipolar disorder and major depressive disorder, revealing mixed associations between coping strategies and symptom severity. While active coping is correlated with better outcomes, emotion-focused coping may exacerbate depressive or manic episodes. Overall, this review underscores the complex interplay between genetic predisposition, environmental stressors, coping mechanisms, and affective disorders. Understanding these interactions is essential for developing targeted interventions and personalized treatment strategies for individuals with mood disorders. However, further research is needed to elucidate specific genomic loci involved in affective disorders and the clinical implications of coping strategies in therapeutic settings.

Aluminum, a contentious trace element found in the environment, has been demonstrated to have harmful effects on both humans and animals. In contrast, Sempervivum tectorum, an evergreen plant, has been found to offer numerous beneficial effects for both humans and animals. Therefore, this study aims to assess the protective effect of S. tectorum on certain reproductive biomarkers in male rats exposed to aluminum. Thirty-five Wistar rats were randomly divided into five groups: NTC (no-treatment control) received distilled water; NC (negative control) received drinking water containing 1 mg/L aluminum sulfate (AS); E1 received 1 mg/L AS along with an 8% S. tectorum extract; PC (positive control) received only 8% S. tectorum extract; E2 received 1 mg/L AS for three months followed by 8% extract for one month. The study analyzed testosterone, LH, FSH, body weight, and the histological structure of the testis, epididymis, and prostate, as well as the levels of zinc, manganese, copper, and iron in these organs. Significant decreases in body weight, testis, and epididymis size were observed in the aluminum-exposed groups compared to the control, whereas these decreases were not significant in the S. tectorum-treated groups compared to the control. Aluminum exposure led to significant decreases in testosterone and LH levels, with FSH levels showing a non-significant decrease in males, which were mitigated significantly by the administration of the plant extract. Histological analysis revealed alterations in the testis, epididymis, and prostate of the AS-exposed groups, including necrosis of seminiferous tubule epithelium and Leydig cells in the testis, and basal epithelial necrosis in the epididymis and prostate. Aluminum levels increased in all organs studied, while levels of zinc, copper, iron, and manganese decreased, showing a negative and significant correlation with aluminum levels. The aqueous extract of S. tectorum demonstrated a protective effect on certain studied biomarkers in male rats affected by aluminum exposure.

Drosophila melanogaster serves as a important research model both for genetic investigations and for the study of metal toxicity, facilitating the elucidation of physiological mechanisms comparable to those of human organisms. In our research, we evaluated the toxicity effect resulting from exposure to various concentrations of lead and copper on the prolificity rates throughout the life cycle (egg-adult) of four genotypes of Drosophila melanogaster: wild-type (control), white, brown, and white-vestigial. During our study, the prolificity rates were examined across three repetitions under the impact of exposure to concentrations of 0.50, 1.00, 2.00, and 4.00 mM of copper (CuSO₄) and lead (Pb(C₂H₃O₂₎₂). Prolificity rates throughout the life cycle exhibited variations as a direct consequence of genetic factors, the concentration of exposure, and the specific type of metal, either copper or lead. The mutant white-vestigial genotype revealed an IC₅₀ concentration for prolificity inhibition at lower doses of 2.00 mM for copper and 4.00 mM for lead, in contrast to the control genotype (wild-type), which exhibited an inhibition concentration rate >IC₅₀ of 4.00 mM only in the case of copper. Our results concluded that the (i) dose influences the prolificity rate in a directly proportional manner, (ii) comparative analyses between copper and lead revealed that copper displayed toxicity across all genotypes within the concentration range of 0.50 mM to 2.00 mM. In contrast, lead exhibited toxicity within the concentration range of 1.00 mM to 4.00 mM, highlighting a (iii) more acute toxicity characteristic in the case of copper. Thus, the results of this research reflect the importance of using Drosophila melanogaster as a genetic model in the comparative study of the interaction between genetic factors and the toxicity of metals, offering significant insights into monitoring their impact and defining the maximum permissible doses on organisms.

There are many uncertainties and risks in residential electricity consumption during the economic development. Knowledge of the relationship between residential electricity consumption and its key determinant—income—are important to the sustainable development of electric power industry. Using panel data from 30 provinces for the 1995-2012 period, this study investigates how residential electricity consumption changes as incomes increase in China. Previous studies typically used linear or quadratic double-logarithmic models imposing ex ante restrictions on the indistinct relationship between residential electricity consumption and income. Contrary to those models, we employed a reduced piecewise linear model that is self-adaptive and highly flexible and circumvents the problem of “prior restrictions.” Robust tests of different segment specifications and regression methods are performed to ensure the conservatism of the research. The results provide strong evidence that the income elasticity was approximately one, and it remained stable throughout the estimation period. The income threshold at which residential electricity consumption automatically remains stable or slows has not been reached. To ensure the sustainable development of the electric power industry, introducing higher energy efficiency standards for electrical appliances and improving income levels are vital. And government should emphasize electricity conservation in industrial sector rather than in residential sector.

Populational aging is marked by chronic non-communicable diseases, such as metabolic syndrome (MetS). IL-10 and IL-1β are pleiotropic cytokines with multiple biological effects linked to metabolic disorders. This cross-sectional study assessed 193 participants' IL-10 and IL-1β serum levels regarding their role in developing MetS, clinical characteristics, and their IL1B rs1143627 and IL10 rs1800890 variants' genotype frequencies in a population over 60. IL-10 levels correlated weakly with HDL levels and fat mass and inversely with triglycerides, glucose, glycated hemoglobin, and estimated average blood glucose levels. IL-10 levels were also indirectly influenced by the patient's T2DM duration, lean mass amount, and bone mineral content. Participants with altered HDL, elevated serum glucose, raised HbA1c levels, or those over 80 had reduced serum IL-10 levels compared to those with normal levels or other age groups, respectively. Women also had higher serum IL-10 levels than men. Dissimilarity, IL-1β levels correlated directly only with the number of total leukocytes and segmented neutrophils, showing only significant variations with self-reported alcohol consumption. Our study also found that those with the IL10 AA genotype (lower IL-10 levels) had a significantly higher risk of developing MetS. These findings may help direct future research and more targeted therapeutic approaches in older adults.

Only a handful of microbial mosquito larval pathogens have been described to date. Sampling of several natural enzootic infections of mosquito larvae in southwestern Florida indicated the presence of microbial pathogens capable of extensive larval mortality. Microscopic analysis of one sample site revealed extensive apparent growth of a Pythium-like microbe on mosquito lar-vae, with highest infection observed on the siphon and head regions. Structures consistent with sporangia were seen on infected insects after lactophenol blue staining, and higher resolution scanning electron micrographs (SEM) showed sporangia and encysted zoospores targeting the head and siphon regions. The isolate was single colony purified and molecular identification targeting the ITS and COX1 loci coupled to phylogenetic reconstruction indicated that the isolate belonged to the Pythium genus, but was distinct from its closest characterized species, P. angusta-tum. Morphological features were characterized, with the isolate showing rapid growth on all mycological media tested and relatively high thermotolerance, capable of robust growth at 37oC, and hence was designated, P. thermoculicivorax. Sampling from a second series of natural infec-tions of mosquito larvae resulted in the molecular identification of three Trichoderma isolates, one with high similarity to T. strigosum, and the other two clustering with, but distinct from, T. asperellum. These data highlight the occurrence of natural enzootic infections of mosquito larvae, potentially as a resource for the identification of new mosquito pathogens.

Natural polluted insulator surfaces are always coated with various kinds of soluble constituents, and those constituents affect flashover performance differentially. Currently this fact is not considered either in laboratory experiments or field pollution degree measurements, causing the existing insulation selection method to be deficient. In this paper a systematical research on insulator flashover voltage gradient correction involving types of soluble pollution constituents was presented. Taking typical type glass insulator as the sample, its flashover tests polluted by typical soluble chemicals NaCl, NaNO₃, KNO₃, NH₄NO₃, MgSO₄, Ca(NO₃)₂ and CaSO₄ were carried out. Then the flashover gradient correction was made combining the flashover performance of each soluble constituent, the ESDD contribution of the seven constituents, as well as the saturation performance of CaSO₄. The correction was well verified with the flashover test results of insulator polluted by three types of soluble mixture. Research results indicate that the flashover gradient correction method proposed by this paper performs well in reducing the calculating error. It is recommended to carry out component measurements and flashover gradient correction to better select outdoor insulation configuration.

Pregnancy is a complex biological process which is associated with significant metabolic and hemodynamic changes of the maternal body which allow a normal fetal growth. The inability to adapt to these changes can affect the cardiovascular health. During pregnancy, women may experience mood swings, anxiety and emotional ambivalence. These symptoms can lead to stress and have a negative impact on the mental well-being of expectant mothers. It is crucial to know the aspects that can influence the development of cardiovascular problems among pregnant women in order to manage these cases properly. The current narrative review explores and summarizes the evidence regarding the impact of stress and anxiety on cardiovascular health in pregnant women. Understanding the physiological adaptations that the body undergoes throughout pregnancy is crucial for educating and supporting individuals as well as healthcare professionals. This enables them to recognize any risk factors or pathological conditions that may exacerbate pregnant women's health. In order to reduce maternal morbidity and mortality from cardiovascular disease, a psychological and cardiovascular risk factor screening that is done either before or during pregnancy may be able to identify situations that call for particular medical and/or psychological therapies.

Terpenes and terpenoids content in cannabis plant was already studied in the past with three used methods. Since these works did not compare the content of these substances under the same conditions, we tried to make this comparison exactly. Three different gas chromatography/mass spectrometry (GS/MS) methods - hexane based liquid extraction (Liq), static head-space extraction (HS), and head-space solid phase microextraction (SPME) – were compared to identify volatile compounds in four different cannabis chemotypes - Green fields, Titan chemotype, Black Domina chemotype, and Neptune chemotype. The main compounds focused on were monoterpenes/monoterpenoids and sesquiterpenes/sesquiterpenoids. Extraction with hexane gave comparable results, however the other two methods allowed for the identification of more substances. For the final evaluation of the comparison of the three methods of analysis, extraction with hexane gives comparable results (which is advantageous for quantitative analysis), although the other two methods allowed for the identification of more substances. This means that the same method should be used everywhere for the quantitative evaluation of constituents in cannabis.

Bartonella species, intracellular parasitic zoonotic pathogens, has drawn increasing attention for their diverse host range and associated human diseases. This study investigates Bartonella infection in small mammals in Yunnan Province, China, focusing on tissue tropism. 333 small mammals were sampled from 13 species, 3 orders, 4 families, and 4 genera in Heqing and Gongshan Counties. Conventional PCR and real-time quantitative PCR (qPCR) were utilized for detection and quantification, followed by bioinformatic analysis of obtained DNA sequences. Results show a 31.5% detection rate, varying across species. Notably, Apodemus chevrieri, Eothenomys eleusis, Niviventer fulvescens, Rattus tanezumi, Episoriculus leucops, Anourosorex squamipes, and Ochotona Thibetana exhibited infection rates of 44.4%, 27.7%, 100.0%, 6.3%, 60.0%, 23.5%, and 22.2%, respectively. Genetic analysis identified 30, 10, and 5 strains based on ssrA, rpoB, and gltA genes, with nucleotide identities ranging from 92.1% to 100.0%. Bartonella strains were assigned to B. grahamii, B. rochalimae, B. sendai, B. koshimizu, B. phoceensis, B. taylorii, and a new species identified in the Episoriculus leucops (GS136). Tissue distribution analysis revealed varied copy numbers across different tissues, with the highest load in spleen. These findings underscore Bartonella's diverse species and host range in Yunnan Province, highlighting its broad tissue tropism in small mammals.

Oil-Gan, also known as emblica, is the fruit of the genus Phyllanthus emblica L. The fruits of these trees are high in nutrients and have excellent effects on health care and development values. There are many methods for the management of diabetic nephropathy (DN). However, there is a lack of effective drugs for treating DN from throughout the disease course. The primary aim of this study was to examine the protective effects (including urine analyses, the measurement of inflammatory cytokine levels, and histological examination) and mechanisms of action of an ethyl acetate extract of P. emblica (EPE) on db/db mice, an animal model of diabetic nephropathy, as well as a secondary aim of examining the expression levels of protein kinase Cα (PKCα) in the kidney and its downregulation of vascular endothelial growth factor (VEGF) and fibrosis gene transforming growth factor-β1 (TGF-β1) by Western blot analyses. Eight db/m C57BLKS/J mice were used as the control group. Forty db/db mice were randomly divided into five groups. Treatments included vehicle, EPE1, EPE2, EPE3 (at doses of 100, 200, or 400 mg/kg EPE), or the comparative drug aminoguanidine for 8 weeks. After 8 weeks of treatment, blood samples were collected for analyses of blood glucose, insulin, and HbA1c levels, and pancreatic and kidney tissues were dissected for histological analyses. The present study indicated that the administration of EPE to db/db mice effectively controlled hyperglycemia and hyperinsulinemia by markedly lowering blood glucose, insulin, and glycosylated HbA1c levels. Administration of EPE to db/db mice decreased the levels of BUN and creatinine both in blood and urine and reduced urinary albumin excretion and the albumin creatine ratio (UACR) in urine. Moreover, EPE treatment decreased the blood levels of inflammatory cytokines, including kidney injury molecule-1 (KIM-1), C-reactive protein (CRP), and NLR family pyrin domain containing (NLRP3). Our findings showed that EPE not only had antihyperglycemic effects but also improved renal function in db/db mice. Histological examination of the kidney by immunohistochemistry indicated that EPE can improve kidney function by ameliorating glomerular morphological damage following glomerular injury; alleviating proteinuria by upregulating the expression of nephrin, a biomarker of early glomerular damage; and inhibiting glomerular expansion and tubular fibrosis. Moreover, the administration of EPE to db/db mice increased the expression levels of p- PKCα/t-PKCα but decreased the expression levels of VEGF and renal fibrosis biomarkers (TGF-β1, collagen IV, p-Smad2, p-Smad3, and Smad4), as shown by Western blot analyses. These results implied that EPE as a supplement has a protective effect against renal dysfunction through the amelioration of insulin resistance as well as the suppression of nephritis and fibrosis in a DN model.

Observe the synergistic effect and dose-effect relationship of Trimethoprim (TMP) on bactericidal activity with Flos Lonicerae in vitro. Microamount chessboard dilution method was conducted to determine the minimal inhibitory concentration (MIC) of Trimethoprim, Flos Lonicerae, as well as the combination of Trimethoprim and Flos Lonicerae separately against Staphylococcus aureus, Escherichia coli in vitro and Salmonella. The pour plate count method was used to determine the combined bactericidal activity of Flos Lonicerae combined with Different concentrations TMP. The results showed that the MIC values of the combination of Flos Lonicerae with TMP was much less than the MIC values of the independent use of Flos Lonicerae or TMP, The FIC values of the combination of Flos Lonicerae with TMP were between 0.5 and 1, there was additive effect between them. The bactericidal rates were fitted with least square method, the 95% confidence intervals of the optimal blending quantity about the combination of Flos Lonicerae with TMP on the test organisms were 231μg·mL^-1-249μg·mL^-1, 237μg·mL^-1-259μg·mL^-1, and 235 -259μg·mL^-1

Type 2 diabetes mellitus (T2DM), a multifactorial and complicated metabolic disorder, is a growing public health problems. Numerous studies indicated that bioactive compounds from herbal medicine have beneficial effects on T2DM prevention and treatment, owing to their numerous biological properties. Curcumin, the major curcuminoid of turmeric, is one of the most studied bioactive components of herbal supplements, which has a variety of biological activities. Clinical trials and preclinical research have recently produced compelling data to demonstrate the crucial functions of curcumin against T2DM via several routes. Accordingly, this review systematically summarizes the antidiabetic activity of curcumin, along with various mechanisms. Results showed that effectiveness of curcumin on T2DM is due to it being anti-inflammatory, anti-oxidant, anti-hyperglycemic, anti-apoptotic, anti-hyperlipidemia and other activities. In light of these results, curcumin may be a promising prevention/treatment choice for T2DM.

To better understand farmers’ refusal and corresponding negative emotions to pay agricultural water fee under current policy in rural China, this paper applies mental accounting, a behavioral economics framework, to explore how the governmental policies of reform of rural taxes and fees, direct agricultural subsidy programs and agricultural water fee individually influence farmers’ decisions in paying agricultural water fee. Using fieldwork data from 577 farmers and 20 water managers in Sichuan, we explore farmers’ information processing regarding paying agricultural water fee via three sequential mental accounting processes, with the associated underlying principles and measures behind each process. We find that the information processing in three mental accounting scenarios related to the agricultural water fee elucidates farmers’ observed behaviors in rural China. Generally, in the three mental accounting scenarios, two conditional intuitive expectations and nine conditional intuitive preferences are formed, however, the conditions of those expectations or preferences cannot be matched with the facts due to the reform of rural taxes and fees, the direct agricultural subsidy programs and the internal attributes of agricultural water fee, which interpret those negative behaviors in rural China. Additionally, this paper offers a view into how previous policies create negative psychological externalities (such as farmers’ psychological dependence on the government) through mental accounting to negatively influence agents’ subsequent decision making; it highlights the significance of underlying mental factors and information processing of negative behaviors in policymaking for managing or conserving common pool resources.

Solvent free copolymerization of epoxides derived from fatty acid esters of waste cooking oil with phthalic anhydride using (salen)CrIII Cl as catalyst and n-Bu4NCl/DMAP as co-catalyst was carried out for the first time under microwave irradiation, where reaction time was reduced from number of hours to minutes. The polyesters were obtained with molecular weight (Mw = 3084-6740 g/mol) and dispersity values (D = 1.18-1.92), when (salen)CrIII Cl/n-Bu4NCl was used as catalysts. While in case of DMAP as a co-catalyst, polyesters with improved molecular weight (Mw = 5537-6925 g/mol) and narrow dispersity values (D = 1.07-1.28) were obtained even at reduced concentrations of (salen)CrIII Cl and DMAP. The obtained products were characterized and evaluated by attenuated total reflection-fourier transform infrared spectroscopy (ATR-FTIR), proton nuclear magnetic resonance (1H-NMR) spectroscopy, gel permeation chromatography (GPC) and thermogravimetric analysis (TGA) Techniques.

Nutritional status problems in school-age children are a crucial public health problem worldwide. This research explored the relationships between family factors, food consumption behaviors, and the nutritional status of Muslim school-age children in Thasala District, Nakhon Si Thammarat Province, Thailand. This descriptive research was conducted among 228 children aged 9-12 years. Data were collected using demographic data, nutritional status, and food consumption behaviors assessment. Data were analyzed using descriptive, chi-square, and binary logistic regression statistics. The results revealed that most samples reported having moderately healthy food consumption behaviors (M = 2.01, SD = 0.56). The samples had a normal weight (72.4%), while 15.8% were classified as overweight and obese. The number of siblings and food consumption behaviors had a significant relationship with nutritional status (p < 0.05). Confirmation with binary logistic regression results also revealed that the likelihood of normal nutritional status was 2.40 times higher in children who had 3 or 4 siblings compared to those with 1 or 2 siblings (AOR = 2.40; 95% CI: 1.299-4.459). Additionally, children with healthy food consumption behaviors were 2.34 times more likely to have normal nutritional status compared to those with unhealthy dietary consumption (AOR = 2.34; 95% CI: 1.183-4.631). Conclusion: Since the number of siblings and healthy food consumption behaviors were associated with nutritional status, healthcare providers must consider these 2 factors when establishing health education and behavior modification care plans to promote healthy food consumption and nutritional status among this group.

In an attempt to reuse fibrous textile waste and, at the same time, to address dye pollution in textile wastewater, waste cotton-based yarn was utilized as both a cheap and sustainable adsorbent and a precursor for carbon adsorbent production. Cotton and cotton/polyester yarn samples underwent thermal modification through carbonization followed by chemical activation with KOH. Various techniques including nitrogen adsorption-desorption isotherms, scanning electron microscopy, Fourier transform infrared spectroscopy, and surface charge determination were employed to analyze the morphological and surface properties of the cotton-based adsorbents. Adsorption properties were evaluated by testing the removal of selected cationic and anionic dyes from water. The impact of temperature, contact time, initial concentration, and pH of the adsorbate solution on adsorption was investigated, with experimental data analyzed using theoretical models. While carbonization alone did not significantly enhance adsorption properties, activated samples exhibited high efficacy in removing both cationic and anionic dyes from water. Despite the negative influence of the polyester component in the carbon precursor on the efficiency of activated samples in removing methyl orange, results indicated that activated cotton and cotton/polyester yarn could be used to prepare highly efficient adsorbents for the rapid removal of methylene blue from real wastewater samples.

Air pollution, climate change and global warming show direct linkage. Introduction - Background: Research in the field has proposed and demonstrated their link to increased allergenicity in plants, leading to increased allergic diseases. Allergen patterns are changing in response to climate change. Across Europe, up to 12% of the population suffers from allergic diseases (bronchial asthma and allergic rhinitis) caused by the pollen grains. The medical costs of these types of allergies are enormous and are increasing with the spread of common ragweed - Ambrosia artemisiifolia* in Europe. In practice, more and more patients are turning to allergists. Methods: Based on these data, the research aims to identify safety measures and specific legislation to control and eradicate common ragweed in the countries most affected by the spread of this plant in Europe, increase in population exposure in countries affected by the presence of common ragweed and the socio-economic impact of allergic rhinitis and bronchial asthma at European level.[1][2] Our database search did not reveal any other research that has addressed this topic to date. Results: This research identifies specific legislation to the countries most affected by the spread of this plant pollen grains at European level, changes in allergen patterns and monitoring/safety eradication measures decided by local authorities, and data on the spread of common ragweed over the last two decades, costs per treatment, increased allergic rhinitis and bronchial asthma morbidity in the most affected areas. Conclusions: At European level, there are no universally valid models for eradicating this weed. Various methods can be used to limit the spread of common ragweed and its pollen production (e.g. mowing once or twice a year of overgrown land, ploughing, chemical control, public information, etc.). Local and regional cooperation should be considered essential to promote phytosanitary & safety measures and exchange of information on methods to identify and manage the spread of common ragweed. Unified legislation at European level would help all affected countries; reduce morbidity from respiratory allergic diseases and the costs of treating these diseases.

This research aims to review the educational and research operations of Mahasarakham University and propose development directions for the university to meet sustainable development criteria for ranking as a green university. This involves gathering data and analyzing the results of operations over the past 3 years, then using this analysis to synthesize lessons learned and develop guidelines for sustainable development in the coming years. The study found that the university's policies and strategies implemented following the annual performance evaluation criteria align with the green university assessment criteria for education and research. This has resulted in minor improvements in curriculum for sustainability. However, community service projects for sustainability have increased by 89.10%, while funding for sustainable research and academic publications related to sustainability has decreased. In summary, the projects under the university's development strategy adequately support and drive suitable development activities. Nevertheless, the university must continuously review its operations to adapt to changing contexts, budget constraints, and evolving competition and develop each year sustainably.

Cutaneous squamous cell carcinoma is a prevalent malignancy with a rising incidence and notably high mutational load. Exploring the genetic nuances of cSCC and investigating molecular approaches stands as a potential avenue for improving outcome in high-risk patients. This retrospective case-control study involved two cohorts of 14 patients (“discovery cohort”) and 12 patients (“validation cohort”) with cSCC located in head-neck anatomical district and diagnosed at pT2 stage. Overall, cases developed early local relapse of the disease whereas controls never re-lapsed during the entire follow-up period. Next generation sequencing (NGS) approach conducted on histological samples revealed that TP53 and CDKN2A were the most frequently mutated genes in our series. No specific mutation was identified as potential prognostic or therapeutic targets. Controls exhibited a tendency toward a higher mutational rate compared to cases. It is possible that an increased number of mutations could prompt the cSCC to expose more antigens, becoming more immunogenic and facilitating the recognition by the immune system. This could enhance and sustain immunological response, potentially preventing future recurrences.

This work aimed to develop an anionic cellulose nanofiber (CNF) bio-adsorbent from palm date tree waste and to investigate its removal efficiency against cationic methylene blue dye from contaminated water. Palm date pulp was first prepared from palm date leaves through acid hydrolysis using H2SO4, followed by hydrolysis in a basic medium using KOH, in which the process completely removed the components of hemicellulose, lignin, and silica. To obtain anionic CNF, the resulting pulp was further treated with H2SO4, followed by centrifugation. Biogel formation of the CNF suspension was promoted by sonication, where its removal efficiency of methylene blue dye was studied as a function of dye concentration, temperature, contact time, and pH value. Two equilibrium models, the Langmuir and Freundlich models were employed, and the Langmuir model was found to be consistent with the experimental data. The highest removal efficiency was obtained at 60oC and was 5mg/gm. Furthermore, several kinetic models were used to gain insight into the adsorption mechanism. The pseudo-second-order model provided an accurate description of the adsorption process, while the Elovich equation suggested a chemical reaction between methylene blue dye and CNF. The study’s findings were in agreement with the pseudo-second-order model, indicating general chemical reactions. The study indicates that CNF adsorbents derived from renewable natural waste sources such as palm date leaves can be effective in removing cationic contaminants such as methylene blue dye.

Spent coffee grounds (SCG) have great potential as a useful, value-added biological material. In this context, activated carbon (AC) was prepared from SCG by an activation process using H3PO4 at 600°C in air and used as an adsorbent for the azo dye AO7, a model molecule for dye colorants found in textile industry effluents. X-ray diffraction, SEM and BET revealed that the AC was predominantly amorphous, consisting of a powder of 20-100 µm particles with mesopores averaging 5.5 nm in pore size. Adsorption kinetics followed a pseudo-second-order law, while the Langmuir model best fitted experimental isotherm data (maximum capacity of 119.5 mg AO7 per AC g). Thermodynamic parameters revealed that adsorption was endothermic and spontaneous. All the characterizations indicated that adsorption occurred by physisorption via mainly - interactions. The best experimental removal efficiency optimized by means of a Box-Behnken design and response surface methodology was 98% for an initial AO7 concentration of 20 mg.L-1 at pH 7.5 with a dose of 0.285 g.L-1 of AC and a contact time of 40 min. These results clearly show that activated carbon prepared from SCG can be a useful material for efficiently removing organic matter from aqueous solutions.

Unmanned vehicles (UVs) have become increasingly important in various scenarios of civil and military operations. The present work aims at the conceptual design of a modular Amphibious Unmanned Ground Vehicle (A-UGV), that can be easily adapted for different types of land and/or water missions, with low monetary cost (<5k€, without sensors). Basing the design on the needs highlighted in the 2021 review of the Strategic Directive of the Portuguese Navy, the necessary specifications and requirements are established for two mission scenarios. Then a market research analysis focused on vehicles currently available, and their technological advances, is conducted to identify existing UVs solutions and respective characteristics/capabilities of interest to the current work. To study and define the geometry of the hull and the configuration of the A-UGV itself, preliminary computational structural and fluid analyses are carried out to ensure it complies with the specifications initially established. As a result, one obtains a fully electric vehicle, with approximate dimensions of 1050×670×450mm (length-width-height), enabled with 6×6 traction capable of reaching 20km/h in land, possesses amphibious capabilities of independent propulsion in water up to 8kts, and with an estimated autonomy of over 60 minutes.

The objective of this paper is to investigate the convergence of coupling-parameter expansion-based solutions to Ornstein-Zernike equation in liquid state theory. The analytically solved Baxter's adhesive hard sphere model is analyzed first using coupling-parameter expansion. It is found that the expansion provides accurate approximations to solutions - including the liquid-vapor phase diagram - in most parts of the phase plane. However, it fails to converge in the region where the model has only complex solutions. Similar analysis and results are, then, obtained using analytical solutions within the mean spherical approximation for the hard-core Yukawa potential. Next, convergence of the expansion is analyzed for the Lennard-Jonnes potential using an accurate density-dependent bridge function in the closure relation. Numerical results are presented which show convergence of correlation functions, compressibility versus density profiles, etc., in the single as well as two phase regions. Computed liquid-vapor phase diagrams, using two independent schemes employing the converged profiles, compare excellently with simulation data. Results obtained for the generalized Lennard-Jonnes potential, with varying repulsive exponent, also compare well with simulation data. All these results together establish the coupling-parameter expansion as a practical tool for studying single component fluid phases modeled via general pair-potentials.

(1) Background: Globally, about 600 million people are afflicted with diabetes, and one of its most prevalent complications is neuropathy, a debilitating condition. At present, the exploration of novel therapies for alleviating diabetic neuropathy-associated pain is genuinely captivating, considering that current therapeutic options are characterized by poor efficacy and significant risk of side effects. In the current research, we evaluated the antihyperalgesic effect of sildenafil (phosphodiesterase-5 inhibitor) – metformin (antihyperglycemic agent) combination and its impact on biochemical markers in alloxan-induced diabetic neuropathy in rats; (2) Methods: The study comprised a cohort of 70 diabetic rats and 10 non-diabetic rats which were submitted to hot, cold, and tactile stimulus tests. Morover, we investigated the influence of this combination on TNF-α, IL-6 nitrites and thiols levels in brain and liver tissues; (3) Results: The results demonstrated that all sildenafil-metformin combinations decreased the pain sensitivity in von Frey test, Hot-plate test and Cold-plate test. Furthermore, alterations in nitrites and thiols concentrations and pro-inflammatory cytokines (specifically TNF-α and IL-6) were noted following a 15-day regimen of various sildenafil-metformin combinations. (4) Conclusions: The combination of sildenafil and metformin has a synergistic effect in alleviating pain in alloxan-induced diabetic neuropathy rats. Additionally, the combination effectively decreased inflammation, inhibited the rise in NOS activity, and provided protection against glutathione depletion.

Plastics, once regarded as a revolutionary material shaping modern society, now poses an unprecedented threat to our environment. Household solid waste sorting stations produce several fractions, one of which contains a high concentration of Low-Density Polyethylene (LDPE) film waste (packaging, sunscreen film, etc.). This fraction is difficult to recycle because it contains quite a lot of impurities. Usually, it is sent to the cement factories that burn it together with other fuels. However, with some processing techniques such catalytic pyrolysis this fraction could be valorized. In this paper the experiments which were carried out at a laboratory scale installation, in batches with a processing capacity of 1-3 kg of waste. The pyrolysis reactor is connected to a distillation column giving the possibility to separate the fractions. The gaseous and liquid fractions were characterized by GC-FID-TCD (gases) and GC-MS (liquids) analysis. Natural catalysts such as bentonite or clinoptilolite were studied and used in the melting of plastic mass to simplify the process as much as possible. To test the activity of the catalysts, the pyrolysis of LDPE granules was initially studied. It was found that natural zeolites are much more active than bentonite and that a minimum concentration of 5-10% is needed to have a positive effect on the composition of the fractions (increasing the weight of the light fractions C1-C6, C6-C10 and C11-C13) in relation to the heavy fractions C13-C20 and C20+. Catalytic pyrolysis gives a completely different distribution of light hydrocarbons. The best catalyst selected from LDPE lab experiments, was then tested upon the pyrolysis of plastic film waste obtained by a waste treatment plant. The research objective reported in this paper was to obtain a fraction of combustible gases in the largest possible proportion, which can be much easier exploited by burning in an engine that drives an electric generator.

The valorization of the large amount of crude glycerol formed from biodiesel industry, is of primordial necessity. One possible direction with high interest to the biorefiniery sector is the production of fuel additives as solketal, though the acetalization of glycerol with acetone. This is a chemical process that conciliates high sustainability and economic interest, since solketal contributes to the fullfilment of a Circular Economy Model through its use in biodiesel blends. The key to guarantee high efficiency and high sustainability for solketal production is the use of a recovery and recyclable heterogeneous catalyst. Some examples are already reported in the literature (first example in 2012), and this review intends to conciliate the information spreaded in this topic and established the most important reacional parameters and the main catalytic characteristics strategies to achieve high solketal production in short reaction time.

The commercialization of historic streets constitutes a pivotal aspect of urban cultural heritage, and the comprehension of their visual perception serves as a valuable asset to urban planning and cultural conservation efforts. However, current research concerning the disparities in visual perception among diverse demographics within historic streets, as well as their spatiotemporal dynamics, remains insufficient. This study aims to utilize mobile eye-tracking technology to delve deeply into the visual perception characteristics of diverse demographics within commercialized historic streets, while also analyzing their spatiotemporal dynamics. We explore the disparities in visual perception of historic streets among groups with varying degrees of architectural knowledge and professional literacy. Through meticulous observation using mobile eye-tracking technology, we elucidate the visual perception patterns of different demographic characteristics through statistical analysis and spatiotemporal modeling. The findings reveal significant discrepancies in visual attention and perception among various groups. Participants with a higher understanding of architecture tend to focus more on architectural details and structures within the streetscape compared to those with a lower understanding, who exhibit greater interest in elements such as shops and signage. Moreover, during the process of perceiving the streetscape, participants’ eye movements transition from surrounding landscapes and historical edifices upon initial entry to the district, gradually shifting towards the commercial activities and distinctive architecture within the district. This study delves deeply into the visual perception characteristics and spatiotemporal dynamics of commercialized historic streets, providing invaluable insights for urban planning and cultural preservation endeavors. By revealing the impact of different demographic characteristics on the visual perception of historic streets, it offers new insights for urban planning and cultural heritage conservation.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

There is a need to find methods to intensify the anaerobic digestion process. One possibility is the use of pre-treatment techniques. Many laboratory tests confirm their effectiveness, but in most cases, there is no verification work carried out on industrial plants. The aim of the research carried out under laboratory conditions and on a large scale was to determine the technological and energy efficiency of the use of hydrodynamic cavitation in the pre-treatment of a waste mixture from dairy farms. It has been shown that hydrodynamic cavitation significantly increases the concentration of organic compounds in the dissolved phase. In the most effective variants, the increase in the content of these indicators was over 90% for both COD and TOC. The degree of solubilisation achieved was 49±2.6% for COD and almost 52±4.4% for TOC. Under laboratory conditions, the highest effects of anaerobic digestion were achieved after 10 minutes of pre-treatment. The amount of biogas was on average 367±18 mL/gCOD and the amount of methane 233±13 mL/gCOD. Further large-scale optimisation trials showed that after 8 minutes of hydrodynamic cavitation, the biogas yield was 327±8 L/kgCOD with a CH4 content of 62.9±1.9%. With this variant, the net energy yield was 66.4±2.6 kWh/day, a value that was 13.9% higher than the original variant with 10 minutes of disintegration and 3.1% higher than the variant without pre-treatment.

Non-tuberculous mycobacteria (NTM) are opportunistic pathogens that cause illness primarily in the elderly, in the immunocompromised or in patients with underlying lung disease. Mycobacterium chimaera is a NTM species belonging to the M. avium Complex (MAC) group of species. Since 2013, a global outbreak of M. chimaera infection related to heater-cooler units (HCU) used in cardio-thoracic surgery has been identified. This outbreak was caused by a single strain of M. chimaera. In order to estimate the prevalence of this outbreak strain in Israel, we sampled M. chimaera from several HCU machines in Israel, as well as from patients, sequenced their genomes and compared them to the outbreak strain. The presence of mixed mycobacteria species in the samples complicated the analysis of obtained sequences. By applying a metagenomic binning strategy, we were able to obtain genomes of single strains from the mixed samples, and characterized them. M. chimaera strains were compared to each other and to previously reported genomes from other countries. The strain causing the outbreak related to the HCU machines was identified in several such machines in Israel but not in any of the clinical samples.

This study aimed to investigate the fatigue performance and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar lap joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Furthermore, the fatigue life of the 14 kV joints was one order of magnitude higher compared to the 12 kV joints. SEM observation of the fatigue fracture surface revealed the presence of typical "tire-mark" fatigue striations only in the 14 kV joint, indicating higher ductility and the ability to withstand extended plastic deformation. Notably, ultra-fine nanocrystalline Al2Cu phase, amorphous phase, and numerous dislocations hindered EBSD acquisition in the transition zone. Nevertheless, dense low-angle grain boundaries (LAGBs) and refined grains were examined at the bonding interface. This suggests that the high-velocity collision caused severe plastic deformation and led to the formation of substructures. The interfacial strength was attributed not only to the "wave-like" or "inverted hook-like" diffusion layer but also to the presence of refined grains along the interface and nanocrystalline Al2Cu in the transition zone. Furthermore, the hybrid nanocrystalline-amorphous microstructure strengthened the joint by regulating the balance between strength and ductility.

Citrus waste has been used as a source of bioplastic research in different ways. Because the juice industry produces significant amounts of residue each year, it would be advantageous to use the byproducts in the creation of new materials. For many years, researchers have been investigating an environmentally friendly way to take citrus and other organic waste and turn it into polymers that may be used, for instance, to produce bio-based and biodegradable films for food packaging. The goal of this study is to create biofilms from orange (OW) and ginger waste (GW) using an ultrafine grinder and study the films' properties. Since pectin has the ability to gel and because cellulosic fibres are strong, citrus waste has been studied for its potential to produce biofilms. After being washed, dried, and milled, orange and ginger waste were shaped into films using a casting process. Tensile testing was used to determine the mechanical properties of biofilms, while dynamic mechanical thermal analysis (DMTA), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC) were used to determine their thermal properties. As the number of grinding cycles increased, the suspension's viscosity increased from 29 to 57 mPa.s for OW and from 217 to 376 mPa.s for GW while the particle size in the suspension significantly decreased. For OW and GW films, the highest tensile strength was 17 MPa and 15 MPa, respectively. The maximum strain obtained among all films was 4.8%. All the tested films were stable up to 150°C, and maximum degradation occurs after 300°C.

The accurate wellbore pressure control not only prevents from lost circulation/blowout and fracturing formation by managing density of drilling fluid, but also improves productivity by mitigating reservoir damage. The geothermal pressure calculated by constant parameters for geothermal well would bring big error easily, as the changes of physical, rheological and thermal properties of drilling fluids with temperature were neglected. This paper researches the wellbore pressure coupling by calculating the temperature distribution with existed model, fitting the rule of density of drilling fluid with temperature and establishing mathematical models to stimulate the wellbore pressures, which is expressed as the variation of Equivalent Circulating Density (ECD) under different conditions. With this method, temperature and ECDs in the wellbore of the first medium-deep geothermal well ZK212 Yangyi Geothermal Field in Tibet were determined, and the sensitivity analysis was simulated by assumed parameters, i.e. circulating time, flow rate, geothermal gradient, diameters of wellbore, rheological models and regimes, the results indicated the geothermal gradient and flow rate were the most influence parameters on the temperature and ECD distribution, and additives added in drilling fluid should be careful which would change the properties of drilling fluid and induce the temperature redistribution. To make sure the safe drilling, velocity of pipes tripping into the hole, depth and diameter of wellbore are considered to control the surge pressure.

The escalating global population and subsequent demand for agricultural products have led to a surge in agricultural waste generation, posing significant disposal challenges. Conventional disposal methods such as burning and dumping not only harm the environment but also jeopardize human health and safety. Recognizing the urgent need for sustainable waste management, researchers have increasingly focused on repurposing agricultural plant waste as a valuable resource. This paper presents a comprehensive review of the potential of agricultural plant waste in wealth creation and sustainable development. It highlights the detrimental impacts of current disposal methods and emphasizes the necessity for alternative approaches. By analyzing the physical, mechanical, and chemical properties of plant fibers, particularly cellulose, hemicellulose, and lignin, this review underscores their suitability for diverse applications. Moreover, it explores the emerging trend of utilizing pineapple leaf fiber, a sustainable and lightweight material, in structural applications such as UAV construction. With its exceptional mechanical properties and biodegradability, pineapple leaf fiber holds promise as a viable alternative to traditional materials, contributing to a more sustainable future. In conclusion, this review advocates for a paradigm shift towards embracing agricultural plant waste as a valuable asset for economic prosperity and environmental sustainability. It underscores the importance of continued research and technological advancements to unlock the full potential of agricultural waste in fostering a circular economy and driving sustainable development globally.

Our previous study has found the anti-tumor activity of oleandrin in osteosarcoma cells in vitro, but the signal transduction process of cell apoptosis induced by oleandrin is uncertain, which is explored in this study. Fluorescence staining and flow cytometry (FCM) was performed to detect the cell apoptosis, intracellular reactive oxygen species (ROS) and mitochondrial membrane potential (MMP). Caspase-3 activity was detected using a commercial kit. The protein expression of cytoplasmic cytochrome c, mitochondrial cytochrome c, bcl-2, bax, caspase-9, Fas, FasL, caspase-8 and caspase-3 was detected using western blot. A pan-caspase inhibitor, z-VAD-fmk, was applied to block the apoptotic pathway and the apoptosis status were re-tested. We found that oleandrin significantly induced the increased apoptosis of U2OS cells. Meanwhile, the intracellular ROS was elevated, but the MMP decreased. The cytochrome c in mitochondria was notably decreased but increased in cytoplasm. The caspase-3 activity was also enhanced with the increase of drug concentration and treatment time. Oleandrin also down-regulated the level of bcl-2, but remarkably up-regulated the expression of bax, cleaved caspase-9, Fas, FasL, cleaved caspase-8 and cleaved caspase-3. Furthermore, the pre-treatment with z-VAD-fmk almost completely reverted the oleandrin-induced apoptosis. The results suggested that oleandrin induces the apoptosis of osteosarcoma cells via mitochondrial- and death receptor-dependent pathways.

The cooling of server components has been continuously developed over the past few years in order to meet the increasing cooling requirements of server component manufacturers such as for the processor chips. The growth in performance and power density increases the cooling demand. These requirements directly influence the energy consumption and performance of the hardware. To gain a better understanding of the historical evolution and possible future technology development paths in the field of data center cooling, a patent analysis method was used. The focus is on previous and current development priorities and possible research gaps within the server and computer room levels. The European patent database was selected as data source. To determine relevant patents, the search terms for various cooling technologies were developed iteratively. After the patent extraction for the period 2000 - 2023 (earliest priority year), the search results were classified and analysed. Most of the patents deal with air or liquid cooling. In the area of liquid cooling, the focus was on direct liquid cooling, followed by total liquid cooling. Since 2015 a technological shift from air to liquid cooling can be identified on the level of patent activities. In this context, the patent groups with focus on “constructional details for different types of electric apparatus” and “electrical digital data processing” have the largest share of patents. In addition, the technology focus of the TOP 10 patent applicants was in the field of liquid cooling. In conclusion from the patent analysis, it can be derived that liquid cooling will continue to gain in importance in the future and could also be combined with other approaches in the form of hybrid cooling. However air cooling may still be relevant, even if the main cooling load is handled by liquid-based approaches. At the same time, the optimisation potential for air cooling seems to have been largely exploited in comparison to liquid cooling, as can be seen from the falling number of the patent applications.

Atmospheric pollens were investigated using the Lanzoni VPSS 2000 device for 2 years between 2012 and 2013 in the Sarıkamış district of Kars province, one of the highest regions of Türkiye. A total of 37909 pollen grains were collected; 15,298 pollen grains in 2012 and 22611 pollen grains in 2013. Out of 43 identified taxa, 21 were arboreal and 22 were non arboreal. Pollen from arboreal plants accounted for 36.34% (13778 pollen) of the total, while pollen from non arboreal plants accounted for 63.56% (24095 pollen). The most frequent arboreal plants pollen in the Sarıkamış atmosphere were Pinaceae (29.79%), Cupressaceae/Taxaceae (2.54%), and Morus (1.30%). The main non arboreal plants pollen in the atmosphere of Sarıkamış were Poaceae (44.60%), Artemisia (2.98%), Amaranthaceae (2.79%), Rumex (2.41%), Urticaceae (2.33%), Plantago (2.19%), and Boraginaceae (1.40%). The maximum pollen concentration was observed in June.

The white wine industry generates a large amount of wastes and composting is an alternative for recycling these residues with agronomic and environmental advantages. With this aim, grape marc and grape stalks were composted in static and turned piles, with 3 and 6 turns, to investigate the effects of pile conditions during composting in order to improve final compost quality. Thermophilic temperatures were attained soon after pile construction, and the highest maximum temperatures were achieved in the turned piles (70.5-71.8 ºC). However, pile moisture content decreased bellow recommended values after day 42 in these piles. The extremely high temperatures and low moisture content in turned piles hampered OM mineralization rates and the amount of potentially mineralizable organic matter (OM0) (391-407 g kg-1), whereas the structure of the static pile provided adequate porosity to increase OM decomposition and OM0 (568 g kg-1). This study shows that composting grape marc with stalks, for a period of 140 days, resulted in stabilized and matured compost (NH4+-N / NO3--N <0.5), with good chemical characteristics for application as soil organic amendment in vineyards, without the need for rewetting or turning the piles, thus reducing the agronomic, and environmental cost of the composting process.

Named herein “CytroCell”, the cellulosic material obtained via hydrodynamic cavitation of citrus processing waste in water is cellulose of low crystallinity, high porosity, good water holding capacity and good dispersibility in water. These properties, here demonstrated for the first time for lemon and grapefruit CytroCell, open the route to mass scale production of a useful functional material from a cheap and abundant biowaste. The process, indeed, does not require any pre-treatment of the raw material, and does not use acid, alkali, chemical oxidants or enzymes.

(1) Background: Intravesical Chemotherapy is standard of care in intermediate risk non-muscle-invasive bladder cancer (NMIBC). Different agents are used across the world based on availability, cost and practice patterns. Epirubicin (EPI), one of these agents is used by many centers over many decades. However, its true differential efficacy compared to other agents and its tolerability is still poorly reported. We aimed to assess the differential efficacy and safety of intravesical EPI in NMIBC patients. (2) Methods: A systematic search of PUBMED, Webofscience, clinicaltrials.gov, and Google Scholar databases was performed on December 31, 2023. We reviewed 28 studies that included patients treated EPI after TURBT (transurethral resection of bladder tumors) for NMIBC and who compared oncological outcomes such as recurrence and progression to other adjuvant treatment such as Mitomycin C (MMC), Gemcitabine (GEM) and BCG. Further, we looked at the safety profile of EPI at room temperature under hyperthermia intravesically and at the oncological outcomes when administrated with hyperthermia; (3) Results: When compared to other chemotherapeutics (MMC/GEM), EPI seemed to be equally effective; however, EPI seems less effective in preventing disease management recurrence compared to BCG intravesical. The most common adverse events of EPI include cystitis, dysuria, and pollakiuria. (4) Conclusions: EPI exhibits similar oncological performances to Gemcitabine and Mitomycin C currently used for adjuvant therapy in NMIBC. Novel delivery mechanisms such as hyperthermia are promising newcomers.

In a vacuum tube two identical and parallel Ag-O-Cs emitters A and B (work function 0.8eV) ceaselessly emit thermal electrons at room temperature. The thermal electrons are controlled by a static uniform magnetic field so that the number of electrons migrate from A to B exceeds the one from B to A (or vice versa). The net migration of thermal electrons from A to B quickly results in a charge distribution of A charged positively and B negatively, and a potential difference between A and B emerges, enabling a continuous output current and a stable power to an external load (e.g., a resistor). Thus, the tube cools down (slightly). The (slightly) cooled tube extracts heat from ambient air, and all the heat is converted into electric energy without other effect. We believe the experiment is in contradiction to the Kelvin statement of the second law.

The limited understanding of how digital platforms, especially the Metaverse, influence public perception and attitude towards sustainable fashion in large scaled markets such as China highlights a critical gap. This study aims to examine the perspectives and perception of the Chinese public regarding sustainable fashion in the Metaverse. Through content analysis, this study evaluated 3,889 Weibo posts from Shanghai Fashion Week 2024 to identify key sentiments and discussions on sustainable and digital fashion. Results indicate that 76.08% of the conversations centered on sustainable fashion, reflecting strong public commitment to environmental issues. The findings highlight characteristics of public perception towards the utilization of immersive technologies and underscore the Metaverse's potential as a platform for fostering environmental consciousness in the fashion industry. This research provides crucial insights for fashion brands looking to integrate sustainability into their digital strategies, addressing a significant gap in current literature and offering practical guidance for leveraging digital platforms to promote sustainable consumption.

In this study, four samples of recycled aggregates from construction and demolition waste of Mexico City were characterized, in order to find innovative uses for this type of materials. Gravel and sand from a recycling plant were analyzed, as well as recycled aggregates in the laboratory from demolished concrete collected in landfills. The characterization was carried out by means of XRD, chemical microanalysis (EDS), pH measurement and sieve analysis. The results reveal that the minerals present in the analyzed materials are triclinic feldspars, cristobalite and pyroxene which correspond to the natural aggregates, as well as variable amounts of calcite, product of the carbonation of the cement paste adhered to these aggregates and in a smaller proportion calcium hemicarboaluminate, rosenhanite and tobermorite. It was determined that the quality (amount of cement) of the original concrete that was recycled, has great influence on the granulometry and the chemical-mineralogical composition of the aggregates, since there will be different quantities and qualities of cement paste adhered to the aggregates of according to size. Finally the pH values measured in all samples fluctuate between 10.15 and 12.08, therefore it is suggested that these materials can be used in soil stabilization.

Present study on land use land cover analysis and taluka wise combination of cropped area, carried out in Beed district of Maharashtra state in India and studied 11 talukas of the district. Secondary data on land use land cover and area in various crops has been collected, compiled and analyzed from various secondary sources. Simple descriptive statistics used to examine the agricultural land use land cover and J.C. Weaver’s crop combination technique was used for taluka wise analysis of crop combinations and on the basis of highest to smallest area engaged in particular crop, crops have been ranked. The study showed that, in the district as a whole, percentage of uncultivated land other than fallow was about 46 percent as compare to net sown area is only 35 percent in total geographical area (1063855ha) of Beed district. The study further revealed that about 42 percent area engaged in food crops and about 58 percent area occupied by nonfood crops, which includes cereals (25%), cotton (19%), pulses (13%), oilseed (12%), sugarcane (5%) and fruits and vegetables (3%). Results of Weaver’s crop combination technique showed that the Wadwani taluka demarcated as most diversified taluka by means of maximum number (sixteen) of crops combinations with the lowest variance value (14) found in the present investigation. Further, the study revealed that the high crop diversity found in Dharur taluka with eighteen crop combinations and the taluka has given first rank amongst others. To derive the crop diversity ranking, taluka wise maximum to minimum number of crop combinations derived in different talukas and given ranks accordingly. The study concluded that, agricultural land use analysis is essential for solving and optimizing the land use problem, maintaining socio-ecological balance, best utilization of scarce resources. The authors enlightened that the rational use of agricultural land has important for food security and biodiversity which increase the productivity and profitability of the agriculture sector and it indicates the decision making ability of farmers in study area.

In this study, a basic study was performed to analyze the seasonal temperature status of a research room in the Global Environment Research Building where ceiling-embedded indoor units are installed to study the room temperature status of the building as well as to improve its thermal environment. In addition, a direction for improvement of the indoor thermal environment in the winter was proposed through a CFD (computational fluid dynamics) simulation and was proven by an additional experiment. Through the results of this study, it appeared that if the ceiling-embedded indoor unit was installed in the small indoor space without considering the thermal vulnerability of its perimeter boundary, the air temperature of the upper part was greatly different from that of the bottom part in the winter. Hence, in this study, as a means to improve it, convectors were installed to minimize the effect of the external thermal environment and angle-controllable air flowing fans were installed to mitigate the stratification distribution. With such result, it was intended to present the essential data for improvement of the thermal environment as well as conservation of heating energy in the winter for buildings by reviewing the use of the ceiling-embedded indoor unit in the future.

Since the public inauguration of the URP (Urban and Regional Planning) Bill in 2009, which is now law (The Urban and Regional Planning Act No. 3 of 2015), urban planning in Zambia has undergone changes. In partnership with the Volunteer Service Overseas (VSO) Federation, the Zambian parliament put into effect pilot urban planning assistance programs to assist districts around the country, including Chipata District in 2011, transition to a more decentralized, integrated and locally-defined approach to urban planning. However, the presence of discrimination, corruption, and negative attitudes towards urban planning engagement, social maladies prominently displayed in Zambian society, pose challenges to implementing the ideal goals of the 2009 URP Bill. The extreme, widespread poverty in Zambia merely exacerbates the propensity towards corrupt and discriminatory behavior, and influences poor attitudes toward urban planning engagement. This paper describes the projects undertaken by the VSO volunteer from the USA between 2011 and 2012 in the light of the specific urban problems facing Chipata District, and discusses the ways the social maladies play out in Zambian society to pose challenges to implementing the recommended changes to the planning system scribed in the 2009 URP Bill.

Biorefineries convert biomasses in bioproducts and they contribute to transition to the circular economy. In this way it will be avoiding the penalty associated with generating a lot of waste. The first step in the obtention chain of bioproducts consists of the high value added products extraction. The following steps are aimed at the utilisation of all by-products or waste generated. The kinetic anaerobic digestion of these residues are evaluated in this research to produce biogas/methane. Pepper waste have been employed in batch and semi-continuous anaerobic digestion assays trying the optimization of the yields adding, as catalysts, absorbent nanoparticles and/or using strategies of pretreatment.

Highlights: A new material with a bending strength higher than that of concrete was developed using vegetable or fruit waste. The new material maintains the color, taste, and flavor of the original vegetable or fruit. Without water resistant treatment, the material is edible and can be conditioned with seasonings

Arc sensors have been used in seam tracking and widely studied since the 80s; commercial arc sensing products for T and V shaped grooves have been developed. However, it is difficult to use these arc sensors in narrow gap welding because arc stability and sensing accuracy are not satisfactory. Pulse gas melting arc welding (P-GMAW) has been successfully applied in narrow gap welding and all position welding processes, so it is worthwhile to research P-GMAW arc sensing technology. In this paper, we derived a linear mathematical P-GMAW model for arc sensing, and the assumptions for the model are verified through experiments and finite element methods. Finally, the linear characteristics of the mathematical model were investigated. In torch height changing experiments, uphill experiments, and groove angle changing experiments the P-GMAW arc signals all satisfied the linear rules. In addition, the faster the welding speed, the higher the arc signal sensitivities; the smaller the groove angle, the greater the arc sensitivities. The arc signal variation rate needs to be modified according to the welding power, groove angles, and swing or rotate speed.

Molecular markers, including Simple Sequence Repeat (SSR), Single Nucleotide Polymorphism (SNP), and Intron Length Polymorphism (ILP), are widely utilized in crop improvement and population genetics studies. However, these marker resources remain insufficient for Musa species. In this study, we developed genome-wide SSR, SNP, and ILP markers from Musa and its sister species, creating a comprehensive molecular marker repository for the improvement of Musa species. This database contains 2115474 SSR, 63588 SNP, and 91547 ILP markers developed from thirteen Musa species and two of its relative species. We found that 77% of the SSR loci are suitable for marker development; 38% of SNP markers originated from the genic region, and transition mutations (C↔T; A↔G) were more frequent than transversion. The database is freely accessible and follows a ‘three-tier architecture,’ organizing marker information in MySQL tables. It has a user-friendly interface, written in JavaScript, PHP, and HTML code. Users can employ flexible search parameters, including marker location in the chromosome, transferability, polymorphism, and functional annotation, among others. These distinctive features distinguish the Musa Marker Database (MMdb) from existing marker databases by offering a novel approach that is tailored to the precise needs of the Musa research community. Despite being an in silico method, searching for markers based on various attributes holds promise for Musa research. These markers serve various purposes, including germplasm characterization, gene discovery, population structure analysis, and QTL mapping.

Telerehabilitation is an appealing service delivery option for optimising recovering. Internationally, the equity of telerehabilitation services for people from culturally and linguistically diverse (CALD) backgrounds has been questioned. Using a 31-item survey, our study explored the access, readiness, and willingness of 260 patients to use allied health telerehabilitation services for adults receiving interventions from a large tertiary health service located in Sydney, Australia. Overall, 72% patients reported having access to technology, 38% met our readiness criteria, and 53% reported willingness to engage in telerehabilitation. There were no difference in access, readiness and willingness to engage in telerehabilitation between patients from CALD and non-CALD backgrounds. Age was the only factor that influenced access, readiness and willingness to engage in telerehabilitation. Past experience of telerehabilitation was related to willingness, but not access or readiness. Findings highlight the importance of ensuring positive patient experiences to promote ongoing willingness to use telerehabilitation. Efforts are needed to improve patients’ digital health literacy, especially patients from older age groups, to ensure equitable access to telerehabilitation services.

The spin-torsion theory is a gauge theory approach to gravity that expands upon Einstein's general relativity (GR) by incorporating the spin of microparticles. In this study, we further develop the spin-torsion theory to examine spherically symmetric and static gravitational systems that involve free-falling macroscopic particles. We posit that the quantum spin of macroscopic matter becomes noteworthy on cosmic scales. We further assume that the Dirac spinor and Dirac equation adequately capture all essential physical characteristics of the particles and their associated processes. A crucial aspect of our approach involves substituting the constant mass in the Dirac equation with a scale function, allowing us to establish a connection between quantum effects and the scale of gravitational systems. This mechanism ensures that the quantum effect of macroscopic matter is scale-dependent and diminishes locally, a phenomenon not observed in microparticles. For any given matter density distribution, our theory predicts an additional quantum term, the quantum potential energy (QPE), within the mass expression. QPE induces time dilation, distance contraction, and thus mimics a gravitational well. When applied to cosmology, our theory yields a static cosmological model. The QPE serves as a counterpart to the cosmological constant introduced by Einstein to balance gravity in his static cosmological model. The QPE also offers a plausible explanation for the origin of the Hubble redshift (traditionally attributed to the universe's expansion). The predicted luminosity distance-redshift relation aligns remarkably well with SNe Ia data from the cosmological sample of SNe Ia. In the context of galaxies, QPE functions as the equivalent of dark matter. The predicted circular velocities align well with the rotation curve data from the SPARC (Spitzer Photometry and Accurate Rotation Curves database) sample. Importantly, our conclusions in this paper are reached through a conventional approach, with the sole assumption of the quantum effects of macroscopic matter on large scales, without the need for additional modifications or assumptions.

Graphene was synthesized through a two-step pyrolysis method using waste candlenut (Aleurites moluccanus) shells as the precursor. Cerium (Ce)/graphene composites were prepared via an impregnation technique. The resulting graphene and Ce/graphene were characterized using various analytical methods, including Scanning Electron Microscopy with Energy-Dispersive Spectroscopy (SEM-EDS), X-ray Diffraction (XRD), X-ray Photoelectron Spectroscopy (XPS), Transmission Electron Microscopy (TEM), Thermo Gravimetric Analysis (TGA), Fourier Transform Infrared (FTIR) spectroscopy, Cyclic Voltammetry (CV), and Linear Sweep Voltammetry (LSV). The bio-carbon produced predominantly exhibited a graphene structure with flat carbon morphology and an interlayer distance of 0.33 nm. This structural information is supported by XRD data, which shows a broad and weak peak at 2θ = 26° corresponding to the C (002) plane, indicative of graphene presence. FTIR, XPS, and Raman spectroscopy further confirmed the presence of graphene through the detection of Csp2 aromatic bonds and the characteristic D, G, and 2D peaks. Notably, the performance of cerium can be enhanced by the incorporation of graphene, attributed to the large surface area and chemical interactions between Ce and graphene. Consequently, candlenut-derived graphene shows potential as a supportive material for modifying the properties of cerium, thereby opening avenues for various advanced applications, such as sustainable and high-performance energy storage systems.

The circular economy (CE) has emerged as a viable alternative for tackling the problems caused by rising consumption, including solid waste (SW). The present study conducted a meta-analysis of research published between 2012 and 2022 on CE and solid waste management (SWM). A bibliometric analysis was used from the Web of Science (WoS) and Scopus databases. By studying the articles, we briefly discussed the connections between them and how one contributes to the evolution of the other. Some findings point to greater collaboration between Italy and Bolivia, followed by China and Malaysia. However, they move away from the traditional axes as the United States and Canada. In addition, it was found that the adoption of reuse and selective collection, in fact, allow the reduction of the volume of discarded materials. In this way, it was possible to conclude that a greater connection between CE and GRS makes it possible to optimize the useful life of landfills through the treatment of organic waste and recycling, to encourage waste picker cooperatives and selective collection programs, and to reduce the financial costs of the system as a whole, making it more durable and sustainable.

The liquid droplet cooling technique for fast scanning chip calorimetry (FSC) is introduced, increasing the cooling rate for large samples on a given sensor. Reaching higher cooling rates and using a gas as the cooling medium, the common standard for ultra-fast temperature control in cooling, requires reducing the lateral dimensions of the sample and sensor. The maximum cooling rate is limited by the heat capacity of the sample and the heat exchange between the gas and the sample. The enhanced cooling performance of the new liquid droplet cooling technique is demonstrated for both metals and polymers, on examples of solidification of large samples of indium, high-density polyethylene (HDPE), and poly (butylene 2,6-naphthalate) (PBN). It was found that the maximum cooling rate can be increased up to 5 MK/s in room temperature environment, that is, by 2 orders of magnitude, compared to standard gas cooling. Furthermore, modifying the droplet size and using coolants at different temperatures provide options to adjust the cooling rate in the temperature ranges of interest.

The introduction of organic and inorganic substances to the environment is a result of human activities such as agriculture, domestic and industrial wastewater which leads to pollution. Treatment processes of these wastewaters are being conducted globally to eliminate easily settled materials and recover nutrients in an attempt to release clear and apparently clean effluent into natural waters. Lack of removing inorganic nitrogen and phosphorus nutrients is the greatest cause of eutrophication in water bodies which inhibits the life of other organisms as well as pose a threat to human life and loss of the economy. Different technologies have been applied and are being developed to recover nutrients as well as heavy metals from wastewater to meet the permissible limits before discharging effluents. Wastewater treatment using microalgae offers an opportunity to provide tertiary bio-treatment and production of valuable biomass. Microalgae use the available inorganic nitrogen and phosphorus for their growth which are then harvested for various uses. Additionally, they have the ability to remove heavy metals and some toxic compounds. The main specific microalgae species in this study is the Chlorella sorokiniana with the Aequorea victoria jellyfish This paper reviews some of the wastewater treatment processes and focus on the use of microalgae and some of the shortcomings of the technologies and how they can be improved to achieve maximum nutrient recovery economically with low energy demand.

The rapid growth of the global population is causing a significant increase in waste production, leading to serious environmental and public health challenges. To address these issues, waste management systems are incorporating advanced technologies. Machine learning and computer vision are used to predict waste patterns, optimize collection schedules, and improve sorting accuracy. Deep learning automates the sorting process, provides predictive analytics, and enhances recycling rates. Robotics, combined with AI and computer vision, improves sorting efficiency, while the Internet of Things (IoT) monitors waste levels and optimizes collection routes. Despite these benefits, challenges such as data scarcity, high computational demands, and the need for substantial infrastructure investments must be addressed. This research explores the integration of advanced technologies into waste management and evaluates their effectiveness using waste datasets. It highlights the potential to tackle environmental challenges and lay the groundwork for more intelligent waste management solutions.

The prevention of destruction caused by red flour beetle, Tribolium castaneum (Herbst), using essential oils derived from certain herbal plants presents an interesting alternative to synthetic insecticides, known for their harm to both consumers and the environment. The research aimed to investigate the chemical compositions and fumigating effects of essential oils derived from cardamom (Elettaria cardamomum (L.) Maton) and galangal (Alpinia galanga (L.) Willd) against T. castaneum. Chemical compositions were analyzed using GC-MS, while fumigation bioassay was conducted via a vapor-phase test. Experimental setup followed factorial design in CRD with 5 replications. Factor A encompassed 4 types of essential oils: the manually extracted essential oils from cardamom leaves (MCL) and galangal leaves (MGL), the commercially produced essential oils from cardamom seeds (CCS) and galangal rhizomes (CGR). Factor B consisted of 7 concentrations: 0, 50, 100, 150, 200, 250, and 300 µL/L air. Results indicated that MCL contained eucalyptol, trans-calamenene, and isospathulenol as its main compounds. Similarly, CCS was characterized by camphene and eucalyptol. MGL exhibited caryophyllene, aciphyllene, and α-bisanolene. Lastly, CGR was composed of methyl cis-cinnamate, safrole, and p-vinylphenyl isothiocyanate. Study noted that 250 µL/L air over 168 hours of CGR, demonstrated 94% fumigation efficiency against adult T. castaneum. These results suggest the potential of galangal rhizome derived essential oil as an insecticide for managing T. castaneum populations in agricultural product storage.

Water pollution is the main problem in the current scenario which is being faced by mankind due to the industrial and commercial effects. Industrial effluents contain heavy metals and inorganic ions like nitrates and phosphate ions. These ions are being included in waterways through industrial runoff. When the concentration of these hazardous pollutants increases in aquatic flora and fauna causes severe health problems. So remediation of these toxicants from water reserves is of chief importance. Conventional processes along with modern processes are being used for the treatment of industrial wastes. Photo-degradation is a modern method used for the degradation of inorganic ions due to its environmentally friendly nature and cost-effectiveness. In a recent study Aluminum oxide (Al2O3) nanoparticles were synthesized via a green approach at different pH by using Cymbopogan citratus (lemongrass) plant extract and these nanoparticles were used for the removal of inorganic ions from wastewater. The nanoparticles of different pH showed different % degradation of the inorganic ions in acidic medium removal of inorganic waste was less, in basic media % degradation was more as compared to acidic media but maximum % degradation was observed in neutral media like that average % degradation 91% and 81% was observed for nitrate and phosphate ions. The maximum absorbance occurred at 212nm and Al2O3 nanoparticles showed absorbance from 210nm-217nm. The R2 values of pseudo1st, 2nd, and BMG models were 0.956, 0.837, 0.7007 0.95, 0.896, and 0.756 for the nitrate and phosphate ions. Characterizations of synthesized particles were investigated by using UV-visible spectroscopy and other analytical methods like X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). The statistical analyses were done using Simple Linear regression (SLR).

The aim of this study was utilization of ground tea waste (GT) left after brewing the black tea as a biofiller of natural rubber (NR) composites. Ionic liquids (ILs), i.e., 1-ethyl-3-methylimidazolium lactate and 1-benzyl-3-methylimidazolium chloride, often used to extract phytochemicals from tea, were applied to improve the dispersibility of GT particles in elastomeric matrix. The influence of GT loading and ILs on curing characteristics, crosslink density, mechanical properties, thermal stability and resistance of NR composites to thermo-oxidative aging was investigated. The amount of GT did not significantly affect curing characteristics and crosslink density of NR composites, but had serious impact on tensile properties. Applying 10 phr of GT improved the tensile strength by 40% compared to unfilled NR. Further increasing in GT content worsened the tensile strength due to the agglomeration of biofiller in elastomer matrix. ILs significantly improved the dispersion of GT particles in elastomer and increased the crosslink density by 20% compared to the benchmark. Owing to the poor thermal stability of pure GT, it reduced the thermal stability of vulcanizates compared to unfilled NR. Most importantly, GT-filled vulcanizates showed improved resistance to thermo-oxidative aging, since the aging factor increased by 25% compared to the unfilled vulcanizate.

This study evaluates the production of biohydrogen from agro industrial waste. The worldwide energy demand is increasing exponentially and the reserves of fossil fuels are depleting, the combustion of fossil fuels has the effect on environment because of CO2 emission. Hydrogen generation market size is forecast to cross 180 billion by 2024, according to a new research report by global market. For the production of biohydrogen. we had chosen groundnut shell as our source, using Tween80 as a surfactant we had undergone pre-treatment studies for (10min,20min,30min,40min,50min) we had estimated the content of cellulose, protein, carbohydrates at (1%,2%,3%,4%,5%) and obtained the optimum value in the form of graph. The production of hydrogen is done by using the rumen fluid of the cow and the quantity of the hydrogen produced by this process is identified by using the analytical instrument Gas Chromatography.

Biofuels have become an integral part of everyday life in modern society. Bioethanol and fatty acid methyl esters are a common part of both the production of gasoline and diesel fuels. Also, pressure on replacing fossil fuels with bio-components is constantly growing. Waste vegetable fats can be replacing biodiesel. HVO seems to be a better alternative. This fuel has a higher oxidation stability for storage purposes, a lower temperature of loss of filterability for the winter time, a lower boiling point for cold starts and other. Viscosity, density, cold filter plugging point of fuel blend, and flash point were measured to confirm that a fuel from HVO is so close to a fuel standard that it is possible to use it in engines without modification. The objective of this article is to show the properties of different fuels with and without HVO admixtures and to prove the suitability of using HVO compared to FAME. HVO can also be prepared from waste materials and no major modifications of existing refinery facilities are required. No technology in either investment or engine adaptation of fuel oils is needed in fuel processing.

The unquenchable demand for rock materials has attracted many companies within the building and construction sector to invest in stone quarrying. However, this has brought about the environmental impacts with health threats to people. There is a paucity of information about the magnitude of pollution on air and water and how it varies with quarry sites. This study therefore investigated the physical impacts of quarrying on air and water and explored the in-situ mitigations to undesirable effects due to stone quarrying. Four active quarry sites were identified. Field measurements of dust (particulate matter) was conducted within the four quarry sites and in the nearby community. Water samples were collected from quarry pits and nearby shallow wells for laboratory analysis of water quality. Statistical Analysis of Variance (ANOVA) was used to test for differences in pollution across the four studied sites. Results revealed that, amidst use of wet crushing and water sprinkling on bare surfaces, dust emission was higher than the recommended permissible standards levels with a significant variation across the quarry sites with ANOVA (P-value=0.003) for PM2.5 and (P-value=0.04366) for PM10. Water pollution was mainly contributed by the non-permissive levels of nitrates, chromium, and pH. Polluted air and water are associated with sparking off health threats to the users in the community. In conclusion, quarry companies should strengthen the already existing mitigation of dust suppression. The study recommends additional measures such as treating quarry pit water before discharging to the open environment

Salmon aquaculture generates a substantial volume of waste material, offering potential for biomaterial production. This industry produces significant waste, which can be repurposed for various biological applications, particularly in biomaterial production for tissue engineering with pertinent applications in osteo-conduction, osteo-induction, and clinical/surgical bone regeneration and repair. The process involves a standardized pre-treatment stage aimed at minimizing biological waste content. Subsequently, the treatment stage, contingent on the chosen methodology, facilitates the removal of proteins, lipids, molecules, and other compounds, leaving the mineral phase as a valuable substrate. The selection of the optimal method, whether alkaline hydrolysis, calcination, or NaOH hydrolysis, for obtaining this substrate necessitates thorough examination through chemical, physical, and biological assessments, including Raman Spectroscopy and X-Ray Diffraction. This study aims to identify the most efficient laboratory process for biofunctional nano-sized hydroxyapatite mineral production derived from Chilean salmon fish backbone waste.

As a hazardous waste, pickling waste liquor must be properly treated. An alternative consists in promoting the formation of ferrous salts from this residue, due to its higher ferrous content. Since FeCl2·4H2O is widely used in several applications, obtaining pure crystals of this material appears to be an interesting prospect. However, this compound has scarcely been investigated. In the present work, FeCl2·4H2O crystals have been obtained from pickling waste liquors. Their structural and morphological characteristics have been investigated by X-ray diffraction, scanning electron microscopy as well as Mössbauer spectroscopy. In addition, the photoluminescence study of the obtained samples was also assessed. It was observed that after some aging time, the obtained crystals change in colour from green to more yellowish. So, the aged sample has also been evaluated, and their structural characteristics are compared with the original crystals. Despite this, the obtained crystals exhibit a FeCl2·4H2O structure, which is not modified with the aging of the sample.

Improper disposal of waste plastic has caused serious ecological and environmental pollution problems. Transforming plastics into high value-added chemicals can not only achieve efficient recycling of waste plastics, but also an effective way to control white pollution. The catalyst selectively breaks the C-C bond of polyolefin plastic under heat treatment and converts it into liquid fuel, thus realizing sustainable recycling of plastics and has a good development prospect. This review provides a detailed overview of the current development of catalytic pyrolysis, catalytic hydrolysis, solvent decomposition and supercritical hydrothermal liquefaction for cracking plastics to make fuel oil. The reaction mechanism, influencing factors and promoting effects of catalysts in various degradation technologies are analyzed and summarized and the latest proposed tandem reaction for degrading plastics is briefly introduced. Finally, some optimization paths of waste plastic pyrolysis to fuel oil technology are proposed: synergies between mixed raw materials, in-depth exploration of catalysts, design and manufacture of reactors that match the pyrolysis technology. All these are important research directions for promoting the industrialization of plastic pyrolysis to fuel oil.

Temperature Cycle Induced Deracemization (TCID) offers a promising approach to obtain enantiopure solids from racemic mixtures. By combining rapid racemization in solution and temperature swings, homochirality is theoretically achieved. Despite theoretical expectations of doubled yields compared to traditional chiral separation methods, such as in Preferential Crystallization, experimental validation remains lacking. We applied TCID to (1-(4-chlorophenyl)-4,4-dimethyl-2-(1H-1,2,4-triazol-1-yl) pentan-3-one) (Cl-TAK), introducing a post-TCID cooling step to enhance yield and a washing step to augment enantiopurity. This refinement yielded an 89.8% mass yield with 99.1% enantiomeric excess in the crystal phase (c.e.e.) within 24 hours on an 8.75g scale, showcasing improved performance with insignificant process duration extension. Additionally, we explored the stochasticity of deracemization, observing the development from low initial crystal enantiomeric excesses(1-6% c.e.e0) at a 2.5 g scale. Kinetic analysis revealed that a 2% c.e.e0 effectively mitigates chiral flipping risks and induction time in our system. Our study underscores the potential for reduced initial c.e.e. to expedite deracemization and presents a straightforward method to optimize yield and purity, facilitating industrial application.

Severe Acute Respiratory Syndrome Coronavirus 2 (SARS-CoV-2) is a single stranded RNA virus which has resulted in the Coronavirus Disease 2019 (COVID-19) pandemic and has infected millions of people all over the world. SARS-CoV-2 has been mutating rapidly resulting in the emergence of multiple variants to escape the host immune system mainly by mutations in its receptor binding domain (RBD) of the spike protein. This rapid evolution of the SARS-CoV-2 posed a great challenge regarding the efficacy and effectiveness of the current SARS-CoV-2 vaccines. The RBD and full-length spike of SARS-CoV-2 is the main target of the neutralizing antibodies. Many SARS-CoV-2 variants are considered to have the potential to escape from the host immune system. In this study, the RBD of Alpha, Beta, Gamma, Kappa and Omicron and the full-length spike of BA.1, BA.2, BA.3, BA.4/5, BQ.1.1 and XBB.1.5 Omicron variants were used as coating antigens in Enzyme Linked Immuno-Sorbent Assay (ELISA) to check the neutralization capability of COVID-19 convalescent sera from patients of first wave of infection occurring in Wuhan. Our results show that the currently circulating Omicron BQ.1.1, XBB.1.5 and previous Omicron BA.1, BA.2 and BA.4/5 do not show significant reduction in neutralization, while Omicron BA.3 and previous variants Alpha, Beta, Gamma, Kappa, and Omicron showed a significantly reduced neutralization when compared to the wild-type Wuhan strain. These results indicate patients recovering from natural infection of early original Wuhan strain may have the potential to resist infection of current circulating variants and the vaccines using the prototype antigen may still working for newly emerged variants.

During the 2008 financial crisis, central banks (such as the Fed) adopted quantitative easing (QE) policy to stimulate their economies and overcome severe economic and financial recessions. However, apart from stimulating the economy by issuing a substantial amount of currency to purchase long-term bonds and suppress interest rates, QE policy also contributed to a boom in the real estate and construction sectors. Therefore, this study employs Data Envelopment Analysis to measure the business performance (BP) of construction companies and explores the impact of QE policy on the BP of construction companies between 2004 and 2015 using ordinary least squares regression. Also, we examine the moderating role of debt ratio on the relationship. Focused on publicly listed construction companies in Taiwan, this research reveals three encouraging find-ings. Firstly, QE policy indeed enhanced the BP of Taiwanese construction companies. Secondly, the performance improvement of construction companies due to QE policy shows a time-diminishing trend, suggesting the importance of seizing the initial policy benefits of QE implementation. Lastly, construction companies with appropriate financial leverage may exhibit better BP. These findings can provide valuable insights for relevant government entities and de-cision-makers in the industry for policy and investment decisions.

Silica fly ash, Certyd aggregate, and an alkaline solution were used to produce lightweight geo-polymer concretes. The compressive strength, water absorption, bulk density and SEM photos showing the structure of the obtained composite were carried out. Tests conducted on the specifi-cation of lightweight geopolymer concretes have revealed significant chemical interactions between the ash aggregate and the geopolymer mortar, particularly when the coarse aggregate surface has been pre-treated with an alkaline solution. Statistical analysis of the experimental data, which in-vestigated the influence of three key variables on compressive strength, water absorption, and bulk density of Lightweight Geopolymer Concrete (LBG), identified the following factors as having the most substantial impact: the quantity of alkali used, the curing temperature, and the concentration of alkali in the mixture. The optimal test series exhibited a commendable compressive strength of 20.14 megapascals (MPa), accompanied by a water absorption rate of 14.72% and a bulk density of 1486.6 kilograms per cubic meter (kg/m³). These findings underscore the importance of alkali con-tent, curing temperature, and alkali concentration in tailoring the properties of lightweight geo-polymer concrete to meet specific performance requirements.

Effective management of the medicine supply chain is crucial for ensuring the availability of essential medicines and supplies in public health facilities. This study aimed to determine the utilization of the electronic logistic management information system (e-LMIS) in public health facilities and its implications for the medicine supply chain. A mixed-methods approach, combining both quantitative and qualitative data collection methods was used. The study was conducted in 106 healthcare providers from 35 public health facilities in Singida District. Six key informants were interviewed in a qualitative method. Of 106 participants, (62.3%) said they were somehow competent in e-LMIS utilization. In in-depth interviews, respondents underscored the system's utility for tracking stock levels, procurements, and managing orders. Staff shortage and lack of customized training were mentioned as major challenges, hindering efficiency in managing drug supplies. This study highlighted the positive impact of e-LMIS on various aspects of the medicine supply chain, including the timely submission of orders and enhanced inventory management. Sustained management support and regular utilization of the e-LMIS system are crucial for building and maintaining competence among healthcare providers, thereby optimizing the medicine supply chain and ultimately improving healthcare delivery.

In the former mining district of La Carolina (southern Spain), waste materials were accumulated without first waterproofing the substrate. Additionally, these mining dams were abandoned without any type of restoration, conditions that present a significant risk of contaminating the surrounding soils and waters. Prior to carry out the necessary works for isolating these residues, morphological characterization of the contact with the base substrate is needed. For that purpose, in recent years, different indirect study techniques have been used, among which electrical to-mography stands out. In this work, a less common geophysical technique, magnetometry, both in its magnetic and gra-diometric modalities, is used as an alternative method to analyse the geometry and structure of a mining dam. The results obtained with this methodology are compared with the results provided by electrical techniques, as well as with direct data from mechanical surveys and aerial photo-graphs prior to waste deposition. The magnetic anomaly curves obtained with geometric models generated with the Mag2dc program were also analysed. This comparative study shows the use-fulness of magnetic prospecting in characterizing the base geometry of these mining structures and therefore the interest in its application to environmental characterization studies.

Whereas waste management research has focused on mostly urban municipalities in South Africa, not much is known about the current performance of waste management services from the perspective of community residents in rural municipalities. This study reports on the status and effectiveness of waste management practices from the perspective of community residents in the Umkhanyakude and Zululand Districts in the rural areas of the KwaZulu-Natal province of South Africa. Making use of structured questionnaires, primary data was obtained by interviewing 333 respondents representing households in the study area. Results have revealed several shortfalls in the provision of municipal waste management services, except for solid waste removal from households (66%), and management of landfill sites (41%). The degree of dissatisfaction for waste management services rendered was very high (97.3%). Furthermore, the majority (61.4%) of respondents were not willing to participate in waste segregation due to lack of appropriate knowledge and infrastructure. The study also pinpointed some benefits associated with waste minimization, as well as barriers constraining effective waste recycling. Based on these findings, there is a dire need for transforming current waste management practices toward increased recycling rates by creating more environmental awareness and a supporting infrastructure.

The article presents the case of a 27-year-old female patient with idiopathic congenital complete heart block who was referred by her primary care physician for cardiological evaluation. The conduction disturbance was recognized at the age of 6 years and was asymptomatic. The disqualification from pacemaker implantation included detailed history of a patient’s symptoms, echocardiographic assessment of the heart, exercise testing and ECG Holter monitoring. The aid of salbutamol administered orally was also useful.

Introduction: Despite great advances in the treatment of oncological diseases, the development of medical technologies to prevent or reduce complications of therapy, in particular, those associated with surgery and the introduction of antibiotics remains relevant. The aim of the study: to evaluate the effectiveness of the use of autoprobiotics based on indigenous non-pathogenic strains of Enterococcus faecium and Enterococcus hirae in the complex therapy of colorectal cancer (CRC) in the early postoperative period. Materials and methods: A total of 36 patients diagnosed with CRC were enrolled in the study. The study group (Group A) comprised 24 CRC patients who received autoprobiotic therapy in the early postoperative period, while the control group (Group C) included 12 CRC patients without autoprobiotic therapy.Prior to surgery and between days 14-16 post-surgery, comprehensive evaluations were conducted on all patients, encompassing the following: stool and gastroenterological complains analysis. examination of the gut microbiota (bacteriological study, quantitative polymerase chain reaction, metagenome analysis), analysis of interleukins in serum. Results: The use of autoprobiotics led to decrease dyspeptic complaints after surgery, was associated with absence of postoperative complications, did not cause side effects, led to a decrease in the level of pro-inflammatory cytokines (IL-6 and IL-18) in the blood serum. The use of autoprobiotics led to positive changes in the structure of escherichia and enterococci populations, the elimination of Parvomonas micra, Fusobacterium nucleatum, decrease in the quantitative content of Clostridium perfringens, Akkermansia muciniphila. Metagenomic analysis (16S rRNA) revealed an increase in alpha diversity. Conclusion: The administration of autoprobiotics in the postoperative period is highly effective and safe in the comprehensive treatment of colorectal cancer patients. Future studies will allow the discovery of additional fine mechanisms of autoprobiotic therapy and its impact on the digestive, immune, endocrine and neural systems.

In globe artichoke both the edible portion and the waste biomass are recognized as valuable sources of bioactive compounds. For this study, heads with 30 cm-long floral stems, including 2-3 leaves, were harvested from five genotypes which included two traditional vegetatively-propagated varietal types (‘Brindisino,’ and ‘Violetto di Foggia,’) and three "seed"-propagated hybrids (‘Tempo,’ ‘Opal,’ and ‘Madrigal’). The study aimed to determine the total and individual polyphenolic concentrations (measured spectrophotometrically and by HPLC) and antioxidant activity (AA) in different artichoke parts, namely the "hearts" (H), head waste (HW), stem waste (SW), and leaf waste (LW). ‘Brindisino’ SW exhibited the highest accumulation of luteolin (26,317 mg kg−1 F.W.), while ‘Tempo’ H displayed the highest cynarin content (190 mg kg−1 F.W.). ‘Tempo’ HW and H showed the highest levels of apigenin (640 mg kg−1 F.W.), and the greatest source of chlorogenic acid was found in the HW of ‘Opal’ and the H of ‘Brindisino’ (4,300 mg kg−1 F.W.). The hybrids generally exhibited lower total polyphenolic concentrations than the traditional genotypes, particularly evident in the LW. The SW demonstrated the highest concentration of total polyphenols (18,000 mg kg−1 F.W.), followed by the edible H and non-edible HW (12,000 mg kg−1 F.W.), while the LW exhibited the lowest concentration (2,000 mg kg−1 F.W.). Interestingly, the AA did not precisely align with the total polyphenolic concentration, showing slight variations between the examined parts and genotypes.

Areca palm sheath leaves were an incredibly noble food packaging system. In ancient times, naturally available wood, leaves, stems, and barks were used to store food materials. But all these were turned down upon the rise of civilization. Today, many modern food packaging systems are used; paper and paperboard packaging materials are used mainly as a replacement for plastic materials. But somehow, paper-based materials have major drawbacks when temperature-dependent products are stored; leaching out components poses a higher threat to health. To alleviate it, bio-based components were used in the manufacturing of paper materials, but the migration of those components was still risky. This study focuses on how the areca palm sheath leaves can be effectively used to prevent this migration of components.

By the end of 2023, biowaste must be completely separated or recycled at source based on the EU legislation. Separate biowaste collection and valorisation towards biofuels could play an essential role in the biobased circular economy. In this context, the principal goal of this paper was to demonstrate in pilot scale the technological solution of bioethanol production via the utilisation of urban source-separated biowaste within the city context of Athens, Greece. More specifically, the main aim was the demonstration of a pilot system in continuous operation (over 10 operating cycles) with real feedstock – wet separately collected biowaste. From the 11 pilot trials performed with wet feedstock, the mean starch and cellulose degradation of the pilot trials amounted up to 80.69±16.27% and 79.41±10.37% respectively, while the bioethanol yield was 74.05±6.82%. The latter was comparable to that of more intensive pretreatment methods. Homogenization and shredding that was applied in this study, stand as promising and cost-effective pretreatment methods for bioethanol production from wet feedstock. Further research is needed to optimize conditions and evaluate scalability. Nevertheless, pilot scale testing is a crucial step in the development and deployment of this technology since it serves as a bridge between laboratory research and full-scale implementation, offering a practical and controlled environment to validate and optimize the technology while minimizing risks and uncertainties.

Antibiotics are released into the environment either directly in an unchanged form or in a partially metabolized form. The discharge is usually through untreated waste or industrial treatment effluents. The potential concern is the uptake of these antibiotics by crops irrigated by treated wastewater. This study collected wastewater from eight points at the Pagla, Kadamtali, Dhaka treatment plant. Here we consider three crucial antibiotics, Doxycycline, Ciprofloxacin, and Tetracycline, used mainly during the last two years of the pandemic. A PDA detector was used in high-performance liquid chromatography (HPLC) analysis to determine the raw and processed effluent antibiotics. The most frequently seen antibiotics in natural wastewater were Doxycycline and Ciprofloxacin, with the highest concentration of 0.23µgL-1and 0.20 µgL-1(raw water), respectively. Tetracycline was not detected in natural water. Contrarily, Doxycycline was discovered in the Pagla plant's completed water and had the highest concentration (0.12 gL-1), whereas Ciprofloxacin and Tetracycline were not found in the dead water. The findings of this study showed that Doxycycline was still present in both the raw and processed effluent. Both natural and finished wastewater was subjected to a microbial-resistant test in the presence of all three antibiotics. The results revealed that the samples detected both heterotrophic bacteria and total coliform. The viable aerobic heterotrophic bacteria ranged between 5.421 and 4.754 log cfu/ml. Total bacteria load gradually decreased in the finished wastewater.

The growing concern about climate change and the recognition of the planet’s limits led society to look for alternatives that promote the balance between the natural and the built environment. The circular economy emerges as an alternative to the linear economic model, inspired by natural metabolisms, by circulating resources in continuous loops, where their intrinsic value is maintained and improved. This research proposes a closed-loop strategy in the built environment by studying innovative constructive solutions that aim to find use, value, and inspiration in what is considered waste. A literature review is conducted on the circular design strategies, re-use and recycle typologies, and waste transformation processes. Then, the development of a methodology for qualitative evaluation and selection of re-used and upcycled construction materials from post-consumer waste and by-products is presented and then applied to thirty-five cases of constructive solutions from plastic, wood, paper, steel, aluminium, and agricultural waste. The research reports that the developed framework is adequate. The analysed alternative materials have good environmental performance and can be used as building materials despite their functional limitations, reflecting the enormous potential of waste as a resource for the construction industry.

Green spaces take part a vital role in reducing the harmful effects occurred through the process of rapid urbanization. This study focuses on evaluating the change of green space and per capita green space in Colombo District, Sri Lanka in between 2008 and 2015 using Landsat images. The NDVI differencing method and classification method were used to detect the change of land cover. According to the results, a gradual decline of green space from 629.1km2 to 591.16km2 with a rate of 6.03% can be depicted. The change is considerable in Kaduwela, Moratuwa and Maharagama DSDs and quite better in the areas such as Avissawella, Homagama and Padukka. The per capita green space has been decreased from 272.361 m2 to 248.811 m2. Though these rates are very well higher than the UN, EU and WHO standards for the district, Colombo DSD do not comply with UN and EU standards. The case would turn into worst in 2025, as the predictions with current rates. Therefore, the study recommends taking immediate actions to make a greener city. Further, a tax system is proposed to get the attraction of the general public.

Households and businesses are generating unprecedented levels of electrical and electronic wastes (e-waste), fueled by modernisation and rapid obsolescence. While the challenges imposed by e-waste are similar everywhere in the world, disparities in progress to deal with it exists; with developing nations such as South Africa lagging. The increase in e-waste generation increases the need to formulate strategies to manage it. This paper presents an overview of e-waste management on a global and South African scenarios with a specific case for Cathode Ray Tube (CRT) waste management practices in South Africa. CRTs present the biggest problem for recyclers and policy makers because they contain hazardous elements such as lead and antimony. Common disposal practices have been either landfilling or incineration. The research into the South African practices with regards to CRT waste management showed that there is still more to be done to effectively manage this waste stream. This is despite clear waste regulatory frameworks in the country. However, recent developments have placed e-waste as a priority waste stream, which should lead to intensified efforts in dealing with it. Overall, these efforts should aim to maximise diversion from landfilling and to create value-addition opportunities, leading to social and environmental benefits.

Background Praziquantel is the commonly used conventional treatment recommended for schistosomiasis in the mainstream healthcare system. Although Praziquantel may be free in healthcare facilities, many individuals may resort to the use of traditional medicine. This study aimed to assess perceptions of participants on the availability of Praziquantel and to ascertain whether individuals infected with schistosomiasis used concurrently African traditional medicines with this treatment. Methods A cross–sectional descriptive study, using face-to-face interviews, was conducted from January to April 2023 among healthcare workers (HCWs) and patients. A review of medical chart records of patients was further carried out to triangulate the information from interviews. Ddescriptive statistics including frequency and percentage were used; categorical data were represented as tables. Chi-squared tests were performed for the association between continuous variables. A p value ≤ 0.05 was estimated as statistically significant. Results Most of HCWs (114/124; 91.9%) reported that Praziquantel was available in healthcare facilities. Majority of HCWs (76/124; 61.3%) did not know whether patients seen by them used concurrently traditional medicine and Praziquantel for schistosomiasis. There was no significant relationship between the availability of Praziquantel and the concurrent use of TM by patients for schistosomiasis (X2 = 3.042, p = 0.551). Patients seen by THPs (8/20, 40%) did not use Praziquantel for schistosomiasis. Those patients (8/15, 53.3%) who crossed from TM to the mainstream healthcare system did not disclose their use of TM to HCWs. Their main reason was that concurrent use of TM and Praziquantel could destroy organs or make Praziquantel not to work properly. None of the medical chart records analysed documented the concurrent use of TM and Praziquantel. Conclusion Most of HCWs were not aware of the concurrent use of TM and Praziquantel by patients for the treatment of schistosomiasis. Patients seen by THPs relied solely on TM for schistosomiasis. Although patients indicated crossing from TM to the mainstream healthcare system, there was no evidence of documented use of TM in medical chart records of patients. Further studies are needed to contribute to the knowledge of medicinal plants used by THPs for schistosomiasis.

The hybrid personal cooling system (HPCS) consisted of ventilation fans and phase change materials (PCMs) covered with insulation pads is a promising wearable cooling system to mitigate heat strain and heat-related illnesses of occupational workers with heavy labor in hot environments. Effects of clothing characteristics (e.g., thermal resistance of insulation pads, latent heat and melting temperature of PCMs) on the thermal performance of the HPCS have been investigated in detail in our previous study. Apart from the aforementioned factors, environmental conditions, i.e., environmental temperature and relative humidity, also significantly affect the thermal performance of the HPCS. In this paper, a numerical parametric study was performed to investigate the effects of the environmental temperature and relative humidity (RH) on the thermal management of the HPCS. Five levels of air temperature under environmental RH=50% were chosen (i.e., 32, 34, 36, 38 and 40 ºC) to study the impact of environmental temperature on the HPCS’s cooling performance. In addition, four levels of environmental RH at ambient temperatures of 36 and 40 ºC were selected (i.e., 30, 50, 70 and 90%) to examine the effect of RH on cooling performance of the HPCS. Results show that high environmental temperatures could accelerate the PCM melting process and thereby weaken the cooling performance of HPCS. In the moderately hot environment (36 °C), the HPCS presented good cooling performance with the maximum core temperature at around 37.5 °C during excise when the ambient RH≤70%, whereas good cooling performance could be only seen under RH≤50% in the extremely hot environment (40 °C). Thus, it may be concluded that the maximum environmental RH for the HPCS exhibiting good cooling performance decreases with the increase in the environmental temperature.

Organic soil amendments, such as composts, mitigate the environmental burdens associated with wasting organic resources. Although compost application to soil enhances an agroecosystem's capacity to store carbon and produce food, studies investigating the agronomical efficacy and their ability to ameliorate drought stress when used as a soil amendment are minimal. In this study, we produced and used a nutrient rich co-compost through the composting of sludge, a nitrogen-rich organic material with carbon rich municipal solid wastes (MSW) to evaluate the agronomic efficacy of the MSW derived co-compost and their ability to ameliorate drought stress. Application of co-compost significantly enhanced growth and yield of lettuce and maize, by a magnitude comparable to chemical fertilizers. Furthermore, under drought stress, lettuce plants grown under co-compost soil amendment grew much better with less wilting, more biomass and yield, and improved root growth. Also, co-compost application enhanced relative root mass ratio (RRMR) under drought stress, indicative that co-compost amendment increased the allocation of biomass to the roots, which is an important morphological attribute for drought adaptability. K content in both leaves and roots of plants amended with co-compost was also higher under drought stress, which may have played a role in osmotic adjustment, consequently, the plants exhibited higher leaf relative water content (RWC). Other nutrient elements that were significantly enhanced by co-compost application included Mg, Ca, Fe and Cu. These results provide evidence that MSW co-composting could optimize organic resource recycling for climate change mitigation and agricultural productivity while minimizing nutrient losses from agroecosystems.

Plastic waste constitutes one of the most important sources of pollution worldwide. Despite the growing recycling trend, nowadays there are no effective technologies that can compensate for the continuous increase in plastic production. Polyesters and polyamides are one of the most produced single-use plastics, mainly used in manufacturing textiles and soft drinks bottles. Today, only a very low fraction of these polymers can be recycled. It can be done by exploiting two leading technologies: mechanical and chemical recycling. Mechanical recycling represents, nowadays, the most used industrial application. However, it can treat a very narrow range of waste materials due to the impossibility of removing dyes and the deterioration of mechanical properties due to the incompatibility of different plastic materials. Another critical limit of this recycling technology is the limited number of recycling loops that can be done due to the thermal degradation that occurs during the extrusion process. The second possibility is chemical recycling, which allows the depolymerization of the original product to recover the monomers directly. The main drawbacks are the long reaction times and the many solvents needed to achieve high-purity products. Therefore, chemical recycling is economically feasible, only for big companies that can produce the virgin polymer in situ. In this work, a new technology has been patented. This process is constituted of three main steps. The first one is the distillation-assisted cyclodepolymerization (DA-CDP), introduced as a modification of the CDP process. In this unit, cyclic oligomers together with high molecular weight compounds have been produced. Then, after polymer purification, it is possible to achieve the same molecular weight of the initial polymer in less than 30 minutes, exploiting the ring-opening polymerization (ROP) in the next step.

Waste glycerol can be subjected to various processing operations, including purification and re-fining, to obtain glycerol of appropriate purity. In addition, alternative methods of utilising waste glycerol are also being sought, e.g. by converting it into other valuable chemical products or biofuels. Therefore, various technologies are being developed to utilise this type of waste effectively and sustainably. The production of value-added products from waste glycerol is an important issue that determines the improvement of the economic viability of biofuel production and corresponds to the model of a waste-free and emission-free circular economy. This paper characterised the mechanisms and evaluated the efficiency of existing methods of microbiological utilisation of waste glycerol into liquid biofuels, including biodiesel, bioethanol and biobutanol, and identified further directions for the production of value-added products. In addition, a bibliographical analysis of publications re-lated to the production of liquid fuels and economically valuable products from glycerol was carried out, the progress of research and application work was assessed and directions for future research were identified.

In the field of visualization, understanding users’ analytical process is important to determine the effectiveness of a designed visualization application. To understand the users’ analytical process, numerous studies have been performed to capture and analyze user interactions. Although many studies have emphasized the importance of analyzing user interactions to understand users’ analytical reasoning processes, few have successfully linked these interactions to users’ reasoning processes. This paper introduces an approach that bridges this gap by correlating semantic user interactions with analysis decisions through an interactive wire transaction analysis system and a visual state transition matrix. With the designed analysis system, interactive analysis can be performed to evaluate financial fraud in wire transactions. It also allows the mapping of captured user interactions and analytical decisions back onto the visualization, revealing users’ distinct results. The visual state transition matrix further aids to help understanding users’ analytical flows, revealing their decision-making processes. Classification machine learning algorithms are applied to assess the effectiveness of our approach in understanding analysts’ strategies by connecting them to their decisions. From the study, we observed an average of 72% accuracy in clearly classifying the semantic user interactions. For classifying individual decisions, we observed an average of 70% classification accuracy. This emphasizes the importance of capturing semantic user interactions to understand users’ analytical processes. Overall, it is determined that the proposed approach not only enhances the understanding of analytical behaviors but also offers a robust approach for evaluating user interactions in visualization tools.

The rapid development of the photovoltaic (PV) industry will result in an increase in the amount of electrical and electronic waste from used PV panels. Only in Poland, the total capacity installed in photovoltaic sources in Poland in May 2020 exceeded 1,950 MW, and the installation weight was approximately 120,000. tone. The problem arises in the recycling or management of this waste. This work presents methods used to recycle waste into photovoltaic modules. The authors investigated the possibility of mechanical and chemical processing of crystalline silicon. A method of thermal treatment of the panel was also proposed. As a result of the research, it was found that the stage of separating materials (crystalline cream, EVO foil, aluminum frame) plays an important role in the recycling process, which is not easy. Chemical treatment allows the silicon to become plastic and the temperature melts the back layer of the panel.

Coffee processing generates a huge amount of waste which contains many natural products. Here, we report the discovery of a panel novel cell-penetrating and metal-ion binding microproteins designated coffeetide cC1a-c and cL1-6 from the husk of two popular coffee plants, Coffea canephora and Coffea liberica, respectively. Combining sequence determination and database search, we showed that the prototypic coffeetide cC1a is a 37-residue, eight-cysteine microprotein with a hevein-like cysteine motif but without a chitin-binding domain. NMR determination of cC1a revealed a compact structure that confers it resistance to heat and proteolytic degradation. Disulfide mapping together with chemical synthesis revealed that cC1a has a ginsentide-like, and not a hevein-like, disulfide connectivity. In addition, transcriptomic analysis showed that the 98-residue micrcoproten-like coffeetide precursor contains a three-domain arrangement like ginsentide precursors. Molecular modeling together with experimental validation revealed a Mg2+ and Fe3+ binding pocket at the N-terminus formed by three glutamic acids. Importantly, cC1a is amphipathic with a continuous stretch of 19 apolar amino acids, and which enables its cell penetration to target intracellular proteins, despite being highly negatively charged. Our findings suggest that coffee by-products could provide a source of ginsentide-like bioactive peptides that have potential to target intracellular proteins.

The extraction of grape processing waste (wine pomace) via microwave-hydrodiffusion and gravity (MHG) from three different cultivars grown in Sicily (Syrah, Perricone and Nero d’Avola) rapidly affords aqueous extracts highly concentrated in valued biophenols including flavonoids, anthocyanins and phenolic acids. The method does not employ organic solvent, acid or base and does not require grinding or freeze drying of the wine pomace nor separation of the grape skins from seeds and stem. All the extracts have a pronounced stability as shown by their red-violet color fully retained after storage for more than a year (15 months) in freezer under air. Concentrations of phenolics up to 2000 ppm were detected in the aged extracts of Sicily’s local cultivar Perricone, which also has the highest content of flavonoids. These findings provide a simple and economically viable extraction route to biophenol-rich red extracts that can be used as food colorants as well as to formulate nutraceutical, cosmetic and personal care products starting from an agricultural by-product available in >10 million tonne yearly amount.

The integral extraction via microwave-assisted hydrodiffusion and hydrodistillation of water-soluble bioproducts contained in the peel of Opuntia ficus-indica white and red cultivars harvested in Sicily, affords red and stable aqueous extracts mostly containing valued betanin, pectin and biophenols. Potentially useful as nutraceutical products, these aqueous extracts are a source of valued ingredients in high demand for a number of important food, cosmetic, beverage and nutraceutical applications.

Carbon fiber reinforced polymers (CFRP) are extensively employed in the aerospace industry due to their excellent properties. Delamination damage occurring at critical locations in CFRP can seriously reduce the safety of in-service components. The detection and localization of delamination damage using Lamb waves hold significant potential for widespread application in non-destructive testing. However, the choice of damage localization algorithm may produce different delamination damage localization results. This research presented an IRAPID (improved reconstruction algorithm for probabilistic inspection of defects) method derived from the ORAPID (original reconstruction algorithm for probabilistic inspection of defects) method, aiming to improve the accuracy and reliability of delamination damage localization. Three CFRP bending plates, including a healthy bending plate and two bending plates with delamination damage sizes of Φ20 mm and Φ40 mm, were prepared in the experiment, respectively. The detection experiment of the CFRP bending plate using lead zirconate titanate (PZT) as a transducer to excite and receive Lamb waves was conducted, and the influence of excitation signal frequency on the performance of the proposed method was discussed. Under the condition of excitation signal frequency of 220 ~ 320 kHz and step size of 10 kHz, the accuracy of the delamination damage localization method proposed in this paper was compared with that of the existing methods. The experimental results indicate that the IRAPID algorithm exhibits good stability in the localization of delamination damage across the frequency variations range considered. The localization error of the IRAPID algorithm for delamination damage is significantly lower than that of the DaS (delay-and-sum) algorithm and the ORAPID algorithm. As the size of the delamination damage increases, so does the localization error. The accuracy of delamination damage localization is lower in the X-axis direction than in the Y-axis direction. By averaging the localization results across various frequencies, we can mitigate the potential localization errors associated with single-frequency detection to a certain extent. For the localization of delamination damage, Lamb waves at multiple frequencies can be employed for detection, and the detection results at each frequency are averaged to enhance the reliability of localization.

As one of the important wastes, waste PET pollutes human living and natural environment seriously. PET is an important solid waste that needs to be recycled at present. The complete degradation of PET was realized at low temperature. The lipophilic hydrophobic membrane was formed on the surface of stainless steel mesh (SSM) by a simple dip coating method, and the oil-water separation material was successfully prepared. Due to the load of degradation products, the surface roughness of SSM increased from 19.09 μm increased to 62.33 μm. The surface changed from hydrophilic to hydrophobic, and the water contact angle increased to 123o. The oil-water separation flux of modified SSM is 9825 L/(m2·h) and the separation efficiency is 98.99%. The modified SSM has good reuse performance. This hydrophobic modification method can also be used to modify other porous substrates, such as activated carbon, filter paper, foam, and other materials. In this study, the porous substrate modified by the degradation product of waste PET was used to prepare oil-water separation materials, which not only solved the problem of white pollution, but also reduced the dependence on non renewable resources in the conventional preparation methods of oil-water separation materials. The research provided new raw materials and methods for the industrial production of oil-water separation materials, and had important application prospects.

An activated carbon manufacturing process using winemaking waste is analyzed and designed at industrial scale. Starting from experimental research, the chemical transformations and thermodynamics during pruning wood conversion are studied as a basis for plant design. In this way, mass and energy balances of hydrothermal carbonization and physical activation are fulfilled and a thermoeconomic methodology is applied to develop an energy-integrated plant. To achieve this target, a network of heat exchangers is allocated to minimize heat consumption and supply hot domestic water, while a cogeneration cycle is designed to provide electricity and satisfy the remaining heat demand. Furthermore, a sensitivity analysis is carried out to determine the influence of the production scale and other operation parameters, such as annual workload, service life, and capital and feedstock costs, on the economic viability of the plant. The energy balance of the plant indicates that the energy integration design manages to provide 48.9% of the overall process energy demand by crossing hot and cold streams and recovering heat from residual flue gas. On the other hand, the exergy cost analysis identifies the combustion of pruning wood used to provide heat demands as the main source of exergy destruction, confirming the suitability of integration to improve the thermodynamic performance. Including activated carbon production, electricity, and hot domestic water, the exergy efficiency of the plant stands at 11.5%.