This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

: Tunnel instability and lining integrity are intimately tied to the creep properties of the surrounding rock. The acquisition of rock mass creep parameters is critical in ascertaining the appropriate timing for lining construction. Nevertheless, creep tests on rock specimens conducted in a controlled setting cannot be straightforwardly extrapolated to rock mass creep analysis. This study performs laboratory-based creep tests on mudstone samples and establishes the corresponding creep constitutive model. Integration of a Mohr-Coulomb element with the Burgers model in series serves to characterise the yield creep behaviour of the rock mass. Additionally, the research outlines a series of 100 orthogonal experiments utilising randomised creep parameters, and formulates a GA-BP neural network inversion model. Employing long-term deformation measurements from the crown and sidewalls of the project site, this study deduces the creep parameters of the mudstone in the investigated tunnel section and examines the prolonged deformation traits of the surrounding rock. Drawing on the deformation traits of the surrounding rock and the forces impacting the primary support and lining structures, this paper evaluates the earliest and latest viable lining casting periods and pinpoints an optimal timing interval for lining implementation. The methodologies employed herein can serve as a benchmark for analogous endeavors internationally.

Large-scale hydrological modeling in China is challenging given the sparse meteorological stations and large uncertainties associated with atmospheric forcing data.Here we introduce the development and use of the China Meteorological Assimilation Driving Datasets for the SWAT model (CMADS) in the Heihe River Basin(HRB) for improving hydrologic modeling, by leveraging the datasets from the China Meteorological Administration Land Data Assimilation System (CLDAS)(including climate data from nearly 40000 area encryption stations, 2700 national automatic weather stations, FengYun (FY) 2 satellite and radar stations). CMADS uses the Space Time Multiscale Analysis System (STMAS) to fuse data based on ECWMF ambient field and ensure data accuracy. In addition, compared with CLDAS, CMADS includes relative humidity and climate data of varied resolutions to drive hydrological models such as the Soil and Water Assessment Tool (SWAT) model. Here, we compared climate data from CMADS, Climate Forecast System Reanalysis (CFSR) and traditional weather station (TWS) climate forcing data and evaluatedtheir applicability for driving large scale hydrologic modeling with SWAT. In general, CMADS has higher accuracy than CFRS when evaluated against observations at TWS; CMADS also provides spatially continuous climate field to drive distributed hydrologic models, which is an important advantage over TWS climate data, particular in regions with sparse weather stations. Therefore, SWAT model simulations driven with CMADS and TWS achieved similar performances in terms of monthly and daily stream flow simulations, and both of them outperformed CFRS. For example, for the three hydrological stations (Ying Luoxia, Qilian Mountain, and ZhaMasheke) in the HRB at the monthly and daily Nash-Sutcliffe efficiency ranges of 0.75-0.95 and 0.58-0.78, respectively, which are much higher than corresponding efficiency statistics achieved with CFSR (monthly: 0.32-0.49 and daily: 0.26 – 0.45). The CMADS dataset is available free of charge and is expected to a valuable addition to the existing climate reanalysis datasets for deriving distributed hydrologic modeling in China and other countries in East Asia.

Estimating ground surface PM2.5 with fine spatiotemporal resolution is a critical technique for exposure assessments in epidemiological studies of its health risks. Previous studies have utilized monitoring, satellite remote sensing or air quality modeling data to evaluate the spatiotemporal variations of PM2.5 concentrations, but such studies rarely combined these data simultaneously. We develop a three-stage model to fuse PM2.5 monitoring data, satellite-derived aerosol optical depth (AOD) and community multi-scale air quality (CMAQ) simulations together and apply it to estimate daily PM2.5 at a spatial resolution of 0.1˚ over China. Performance of the three-stage model is evaluated using a cross-validation (CV) method step by step. CV results show that the finally fused estimator of PM2.5 is in good agreement with the observational data (RMSE = 23.00 μg/m^3 and R2 = 0.72) and outperforms either AOD-retrieved PM2.5 (R2 = 0.62) or CMAQ simulations (R2 = 0.51). According to step-specific CVs, in data fusion, AOD-retrieved PM2.5 plays a key role to reduce mean bias, whereas CMAQ provides all-spacetime-covered predictions, which avoids sampling bias caused by non-random incompleteness in satellite-derived AOD. Our fused products are more capable than either CMAQ simulations or AOD-based estimates in characterizing the polluting procedure during haze episodes and thus can support both chronic and acute exposure assessments of ambient PM2.5. Based on the products, averaged concentration of annual exposure to PM2.5 was 55.75 μg/m3, while averaged count of polluted days (PM2.5 > 75 μg/m3) was 81, across China during 2014. Fused estimates will be publicly available for future health-related studies.

In this paper, we first discuss the research status and application progress of the finite element method and the smoothed particle method. By analyzing the advantages of the smoothed particle method and the finite element method, a new coupling algorithm, namely FEM-SPH algorithm, is proposed. By the method of comparison, it shows that finite element method and SPH method in the simulation of large deformation problems each have advantages and disadvantages, the finite element method smoothed particle coupling algorithm is effective to achieve the performance of high computational efficiency and can naturally simulate large deformation problems across. In the process of calculation, the large deformation unit can be freely into an algorithm to facilitate the calculation accuracy and efficiency of three methods of numerical simulation. Through the study found, FEM-SPH algorithm not only overcome the defect of smooth particle tensile instability, but also overcomes the problem of low efficiency of finite element computation. To further test the FEM-SPH algorithm has advantages in the practical engineering, we have carried out the actual test to the example of the super high speed collision, concluded that, since the target of most of the computational domain is always finite element, smoothed particle focused only in contact with the projectile and target of local area, particle number is not much, the whole calculation process just ten minutes, computational efficiency has been greatly improved, at the same time in the simulation of large deformation, the advantage is very obvious .This provides a criterion for the actual project, depending on the specific material deformation mode and choose a more appropriate conversion algorithm.

In this paper we report a new development on the numerical model for aluminum-steam combustion. This model is based on diffusion flame of continuum regime and the thermal equilibrium between the particle and the flow field, which can be used to calculate the aluminum particle combustion model for two phase calculation conditions. The model prediction is in good agreement with the experimental data. A new type of vortex combustor was proposed for the combustion of aluminum and steam, and the mathematical model of the two phase reacting flow with in this combustor was established. The turbulence effects are modeled using the Reynolds Stress Model (RSM) with Linear Pressure-Strain approach, and the Eddy-Dissipation model is used to simulate the gas phase combustion. Aluminum particles are injected into the vortex combustor and form a swirling flow around the chamber and their trajectories are traced using the Discrete Phase Model (DPM). The simulation results show that the vortex combustor can achieve high efficient combustion of aluminum and steam. The influencing factors, such as the eccentric distance of the inlet of aluminum particles, particle size and steam inlet diameter, etc., are studied. The work described in this paper represents an attempt to the design of a vortex combustor in order to increase aluminum combustion efficiency.

Frontal Polymerization (FP) is recognized as a polymer synthesis method capable of generating a highly localized and self-propagating exothermic front, considered a more rapid and energy-efficient manufacturing scheme for polymer-based fiber-reinforced composite materials. This study conducts a numerical investigation based on the Finite Element Method into the initiation and propagation of frontal polymerization of acrylamide. Utilizing Differential Scanning Calorimetry (DSC) experiments, the study phenomenologically tests the curing kinetics reactions of acrylamide (AM) in deep eutectic solvent (DES)-based polymerizable systems, thereby establishing a curing kinetics model for the autocatalytic reaction of polyacrylamide. By coupling the heat conduction diffusion equation of the frontal polymerization reaction, the Finite Element Method is employed to solve the reaction-diffusion model, aiming to explore the evolution of temperature and degree of curing during the manufacturing process. The results demonstrate the reliability and accuracy of the nth-order autocatalytic model in the study of curing kinetics for DES-based synthesis, indicating that the front propagation speed of the AM-based FP reaction is influenced by the activation temperature, duration of activation temperature, and initial temperature of the solution. Experimental validation of the polyacrylamide manufacturing through frontal polymerization corroborates the accuracy and reliability of the model predictions, providing a reference for the numerical model study and temperature control in the synthesis of acrylamide composite hydrogels via FP.

Addressing the significant challenge in high-speed cotton dibbling operations in Xinjiang—specifically, the duck bill’s ("Duck bill" is a type of duck-billed bunch planting mechanism or component). shortened opening duration leading to seed throwing and floating—a new crawler-type delayed hole-forming mechanism has been designed. This mechanism extends the duck bill horizontally, thereby prolonging its opening time, enabling cotton sowing speeds of up to 6 km/h. Following agronomic principles for cotton planting, the overall layout of the crawler-type hole-forming mechanism, the structural parameters of the key components and the trajectory of the hole-forming are determined. We use the Discrete Element Method (DEM) and multi-body dynamics coupling method to simulate and analyze the motion process of the device. The fixed the tilt angle of the duck bill α(A), the depth of the duck bill hole-forming into the soil h(B), and the angle of rotation of the moving duck bill β(C) were taken as the experimental factors, with the longitudinal length of cotton seed hole (Y1) and the hole-forming depth of cotton seed hole (Y2) as the response values. The parameter range of each factor and the preliminary influence on the response value were determined through pre-experiments and single-factor simulation test. Based on RecurDyn-EDEM coupling, a quadratic regression orthogonal rotation combination simulation test was carried out. The results show that the order of the primary and secondary factors affecting the Y1 of the time-lapse hole-forming device was: A > C > B. The order of primary and secondary factors affecting the Y2 of the delayed hole forming device was: B > C > A. When the A was 2.4 °, the B was 42.4 mm, and the C was 30.5 °, the performance of the hole-forming was the best, and the Y1 was 26.4 mm, and the Y2 was 25.0 mm. The bench verification test results show that under the optimized combination of operating parameters, the average Y1 was 29.1 mm, and the average Y2 was 23.2 mm. Compared with the results of the previous coupled simulation model, the average relative errors of the two are 7.23 % and 4.36 %, respectively, indicating the accuracy and effectiveness of the established DEM simulation model and virtual test analysis. The hole-forming area and the opening time of the duck bill after the stable operation of the machine were recorded and measured. The calculated hole dislocation rate Hc was 4.33 %, which did not exceed the national standard requirement of 6 %. The qualified rate of hole distance Hx was 94.33 %, which was much higher than the national standard requirement of 80 %. The average opening time of the duck bill at a speed of 6 km/h is 0.45 s, which is much longer than the time required for cotton seeds to fall from the duck bill 0.11 s. It meets the requirements of high-speed cotton planting in China and facilitating advancements in future high-speed planter technology.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

Due to the optical properties of the Electron Transport Layer (ETL) and Hole Transport Layer (HTL), inverted perovskite solar cells can perform better than traditional perovskite solar cells. It is essential to compare both types to understand their efficiencies. In this article, we studied inverted perovskite solar cells with NiOx/CH3NH3Pb3/ETL (ETL = MoO3, TiO2, ZnO) structures. Our results showed that the optimal thickness of NiOx is 80 nm for all structures. The optimal perovskite thickness is 600 nm for solar cells with ZnO and MoO3, and 800 nm for those with TiO2. For the ETLs, the best thicknesses are 100 nm for ZnO, 80 nm for MoO3, and 60 nm for TiO2. We found that the efficiencies of inverted perovskite solar cells with ZnO, MoO3, and TiO2 as ETLs, and with optimal layer thicknesses, are 30.16%, 18.69%, and 35.21%, respectively. These efficiencies are 1.5%, 5.7%, and 1.5% higher than those of traditional perovskite solar cells. Our study highlights the potential of optimizing layer thicknesses in inverted perovskite solar cells to achieve higher efficiencies than traditional structures.

The fractional advection-dispersion equation FADE plays an important role, especially in explaining the process of solute-transport in natural porous media with different degrees of heterogeneity. However, studies of the flow and transport of contaminants in the underground environment are based on the knowledge of many functional parameters of the subsoil. The delay factor caused by nonlinear absorption is one of these parameters inheriting significant ambiguities in its estimation in heterogeneous media. In the study, a fractional advection-dispersion FADE model was developed by the implicit Euler method, based on a Grunwald and Caputo-Liousville approximation to explicitly evaluate and simulate the transport mechanism of contaminants in media with unsaturated porous materials subjected to a nonlinear sorption model. Better solute mass retention was observed for fractional advection-dispersion FADE model. Moreover, the absorption parameter of the retardation coefficient has a better impact on the motion of the solute in a saturated porous medium. In other words, it has a significant effect on the dispersion of pollutants in aquifers. This study highlights the need to characterize the aquifer to predict solute transport in porous media.

Urban rail transit hub platform is the most important area for passenger flow distribution. In order to calculate passenger flow volume in platform and evaluate platform service level during rush hours, this paper presents a method for modeling and simulation of passenger flow distribution in platform. Passenger flow distribution model (PFDM) is proposed based on the basic analysis and the superposition principle of passenger flow. Simulation design for PFDM is proposed by Anylogic, which contains simulation process and simulation model. Experiment results show that PFDM and simulation design are effective and accordant with the reality scenario, and the simulation precision is comparatively ideal. This research could provide a beneficial reference for train scheduling and operation management under the viewpoint of traffic safety and service level.

In the recent years, tubular nanostructures have been related with immense advances in various fields of science and technology. Considerable research efforts have been centered on the theoretical prediction and manufacturing of non-carbon nanotubes (NTs), which meet modern requirements for the developing of novel devices and systems. In this context, diatomic inorganic nanotubes formed by atoms of elements from the 13th group of the periodic table (B, Al, Ga, In, Tl) and nitrogen (N), have received much research attention. In the present work, the elastic properties of single-walled boron nitride, aluminium nitride, gallium nitride, indium nitride and thallium nitride nanotubes were numerically evaluated using the nanoscale continuum modelling approach (also called molecular structural mechanics). The elastic properties (rigidities, surface Young´s and shear moduli, and Poisson´s ratio) of nitride nanotubes are discussed with respect to the bond length of the corresponding diatomic hexagonal lattice. The results obtained contribute to a better understanding of the mechanical response of nitride compound-based nanotubes, covering a broad range from the well-studied boron nitride NTs to the hypothetical thallium nitride NTs.

Crop production in Afghanistan suffers from limited phosphorus (P) availability, which severely hinders national agriculture sustainability. This present study hypothesized that deep fertilizer placement could significantly enhance uptake of immobile P and thus tissue P accumulation and crop yield. A two-year pot experiment growing two maize (Zea mays) hybrid cultivars (Xida-789 and Xida-211) was therefore conducted to test these hypotheses under three contrasting fertilizer placement methods (broadcast, side band, and deep band). In doing so, P concentrations in both maize tissues and soils were compared at 45, 60, and 115 days after sowing (DAS) under nine combinations of nitrogen (N) and P fertilizer rates (kg ha-1: N112P45, N112P60, N112P75, N150P45, N150P60, N150P75, N187P45, N187P60, N187P75). Results have shown that deep band placement significantly increased P uptake efficiency, leading to greater P concentration and accumulation in maize tissues compared to other two fertilization methods. This improved P uptake was attributed to several factors associated with deep placement, including reduced P fixation, enhanced root access to P, and moisture availability for P uptake. Additionally, deep band placement combined with higher N application rates (N187 and N150) further enhanced plant P uptake by promoting P availability and utilization mechanisms. Deep band placement also resulted in significantly higher total soil P, Olsen-P, and P use efficiency than broadcast and side band methods, indicating a more efficient P fertilization strategy for maize that can improve growth and yield. This present study also found positive correlations between P concentration in plant organs and soil Olsen-P, highlighting the importance of adequate soil P levels for optimal plant growth. Overall, our results have showed that deep band fertilizer placement emerged as a superior strategy for enhancing P uptake efficiency, utilization, and maize productivity compared to broadcast and side band placement. This approach can potentially optimize P fertilizer utilization, improve maize growth and yield, while minimizing environmental P losses associated with broadcast applications.

Selecting road networks in cartographic generalization has consistently posed formidable challenges, driving research towards the application of intelligent models. Despite previous efforts, the accuracy and connectivity preservation in these studies, particularly when dealing with road types of similar sample sizes, still warrant improvement. To address these shortcomings, we introduce a Heterogeneous Graph Attention Network (HAN) for road selection, where feature masking method is initially utilized to assess the significance of road features. Concentrating on the most relevant features, two meta-paths are introduced within the HAN framework: one for aggregating features of the same road type within the first-order neighborhood, emphasizing local connectivity, and another extending this aggregation to the second-order neighborhood, capturing a broader spatial context. For a comprehensive evaluation, we introduce a set of metrics considering both quantitative and qualitative aspects of the road network. Compared to traditional neural networks, our HAN model demonstrates superior accuracy and F1-score, particularly for road types with comparable samples. Additionally, it enhances the overall connectivity of the selected network. In summary, our HAN-based method provides an advanced solution for road network selection, surpassing previous approaches in terms of accuracy and connectivity preservation.

Conditions under which compositions of component systems form a well-defined system-of-systems here are formulated at a fundamental level. Statement of what defines a well-defined composition and sufficient conditions guaranteeing such a result offers insight into exemplars that can be found in special cases such as differential equation and discrete event systems. For any given global state of a composition, two requirements can be stated informally as: 1) the system can leave this state, i.e., there is at least one trajectory defined that starts from the state, and 2) the trajectory evolves over time without getting stuck at a point in time. Considered for every global state, these conditions determine whether the resultant is a well-defined system and if so, whether it is non-deterministic or deterministic. We formulate these questions within the framework of iterative specifications for mathematical system models that are shown to be behaviorally equivalent to the Discrete Event System Specification (DEVS) formalism. This formalization supports definitions and proofs of the afore-mentioned conditions. Implications are drawn at the fundamental level of existence where the emergence of a system from an assemblage of components can be characterized. We focus on systems with feedback coupling where existence and uniqueness of solutions is problematic.

CO2 is widely used in the prevention and control of coal spontaneous combustion. In this manuscript, three low-rank coals with different metamorphic degrees were selected as the research objects. The temperature-programmed experiments, in-situ infrared cooling experiments, simulation of competitive adsorption of CO2 and O2 in coal pores, and simulation study of CO2 inhibition of coal oxygen composite reaction were used to obtain the role and effect of CO2 in preventing oxygen adsorption in coal at low-temperature oxidation stage. It is concluded that CO2 can displace the O2 near the pore wall to physically prevent the adsorption of O2. Through the change law of heating rate and kinetic analysis, it is found that CO2 can increase its activation energy by 5.3%-108.3% during the slow heating stage of coal, and reduce its heating rate. At around 120°C, coal loses the protective effect of CO2. From the changes of functional groups, it can be seen that when coal is cooled in CO2 atmosphere, mainly pyrolysis and condensation reactions occur due to the lack of O2. In addition, CO2 can also inhibit the chain reaction of coal's chemical adsorption of oxygen. This work provides a theoretical basis for CO2 prevention and control of coal spontaneous combustion.

In Cameroon, Aedes mosquitoes transmit various arboviruses, posing significant health risks. We aimed to characterize the Aedes virome in southwestern Cameroon and identify potential core viruses which might be associated with vector competence. A total of 398 Aedes mosquitoes were collected from four locations (Bafoussam, Buea, Edea and Yaounde). Aedes albopictus dominated all sites except for Bafoussam where Aedes africanus prevailed. Metagenomic analyses of mosquitoes grouped per species into 54 pools revealed notable differences in eukaryotic viromes between Ae. africanus and Ae. albopictus, with the former exhibiting greater richness and diversity. Thirty-seven eukaryotic virus species from 16 families were identified, including six novel viruses with near complete genome sequences. Seven viruses were further quantified in individual mosquitoes via qRT-PCR. Although none of them could be identified as core viruses, Guangzhou sobemo-like virus and Bafoussam mosquito solemovirus virus were highly prevalent regionally in Ae. albopictus and Ae. africanus, respectively. This study highlights the diverse eukaryotic virome of Aedes species in southwestern Cameroon. Despite their shared Genus, Aedes species exhibit limited viral sharing, with varying viral abundance and prevalence across locations. Ae. africanus, an understudied vector, harbors a rich and diverse virome, suggesting potential implications for arbovirus vector competence.

Cloud computing refers to applications delivered as services over the Internet. Cloud systems employ policies that are inherently dynamic in nature and that depend on temporal conditions defined in terms of external events, such as the measurement of bandwidth, use of hosts, intrusion detection or specific time events. In this paper, we investigate an optimized resource management scheme named v-Mapper. The basic premise of v-Mapper is to exploit application-awareness concepts using software-defined networking (SDN) features. This paper makes three key contributions to the field: (1) We propose a virtual machine (VM) placement scheme that can effectively mitigate the VM placement issues for data-intensive applications; (2) We propose a validation scheme that will ensure that a service is entertained only if there are sufficient resources available for its execution and (3) We present a scheduling policy that aims to eliminate network load constraints. An evaluation was carried out with various benchmarks and demonstrated that v-Mapper shows improved performance over other state-of-the-art approaches in terms of average task completion time, service delay time and bandwidth utilization. Given the growing importance of supporting large-scale data processing and analysis in datacentres, the v-Mapper system has the potential to make a positive impact in improving datacentre performance in the future.

Some peptide-based drugs including oxytocin, vasopressin, ziconotide, pramlintide, nesiritide, and octreotide, contain one intramolecular disulfide bonds. A novel and reusable monodispersed silica nanosphere-supported Pt(IV) complex (SiO2@TPEA@Pt(IV)) was synthesized via a four-step procedure and used for formation of intramolecular disulfide bonds in peptides. TEM and chemical mapping results for the Pt(II) intermediates and for SiO2@TPEA@Pt(IV) show that the silica nanospheres possess a monodisperse spherical structure and contain uniformly distributed Si, O, C, N, Cl, and Pt. The valence state of Pt on the silica nanospheres was characterized by XPS. The Pt(IV) loaded on SiO2@TPEA@Pt(IV) was 0.15 mmol/g, as determined by UV-vis spectrometry. Formation of intramolecular disulfides in six dithiol-containing peptides of variable lengths by use of SiO2@TPEA@Pt(IV) was investigated and the relative oxidation yields were determined by HPLC. In addition, peptide 1 (Ac-CPFC-NH2) was utilized to study the reusability of SiO2@TPEA@Pt(IV). No significant decrease in the relative oxidation yield was observed after ten reaction cycles. Moreover, the structure of SiO2@TPEA@Pt(IV) after being used ten cycles was determined to be similar to its initial one, demonstrating the cycling stability of the complex.

Pipeline conflicts arising from data dependencies are a common issue encountered in the hardware implementation of layered QC-LDPC decoders. This paper proposes an efficient layered decoding architecture to reduce pipeline conflicts without introducing stall cycles, by reordering the processing order offline and using the patch method based on variable-to-check message. The experimental results on the LDPC code of the IEEE802.16 standard in the OFDM-PON system demonstrate that the proposed architecture has a sensitivity improvement of 0.125 dBm and 0.375 dBm, respectively, compared with our previous work and the method described in the other work.

The normal growth and development of skeletal muscle is essential for the health of the body. The regulation of skeletal muscle by intestinal microorganisms and their metabolites has been continuously revealed. Acetate is the predominant short-chain fatty acid synthesized by gut microbiota through the fermentation of dietary fiber, however, the underlying molecular mechanisms governing the interaction between acetate and skeletal muscle during rapid growth stage remain to be further elucidated; Here, specific pathogen-free (SPF) mice, germ-free (GF) mice, and germ-free mice supplemented with sodium acetate (GS) were used to evaluate the effects of acetate on skeletal muscle growth and development of young mice with gut microbiota deficiency; We found the concentration of serum acetate, body mass gain, succinate dehydrogenase activity and expression of myogenesis maker gene of skeletal muscle in the GS group was higher than GF group following sodium acetate supplement. Furthermore, the transcriptome analysis revealed that acetate activated biological processes regulating skeletal muscle growth and development in GF group that are inhibited due to gut microbiota deficiency. In vitro experiment, we proved that acetate up-regulated Gm16062 to promote skeletal muscle cell differentiation; Overall, our findings proved that acetate promote skeletal muscle growth and development in young mice via increase Gm16062 expression.

A low cost, scalable and robust process has been proposed as innovative method for coating solar mirrors with a self-cleaning, transparent in the full solar range and versatile material based on auxetic aluminium nitrides, previously obtained on the laboratory scale. This work presents the scaling-up of fabrication process from laboratory to prototypal scale and pre-liminary results of outdoor self-cleaning solar mirror prototypes testing in the demonstrative CSP plant ENEASHIP located in Casaccia (Rome) ENEA research centre. Prototypes 50x40cm have shown stability in external conditions: no degradation occurs during the test campaign. Their washing restores the initial reflectance affected by soiling and the self-cleaning performance allows the utilization of a reduced quantity of water for cleaning operations with respect to uncoated glass of back surface mirrors. A similar self-cleaning AlN coating could be utilized on other solar components affected by soiling, such as glass envelopes of heat collecting elements, PV panels and everywhere are required self-cleaning performance combined to optical ones.

A challenge in building large-scale superconducting quantum processors is the precise control and manipulation of the qubit state. However, the crosstalk between the microwave control lines impedes the parallel execution of high-fidelity digital and analog quantum operations. Here, we propose and demonstrate a universal compensation protocol for calibrating the microwave signal crosstalk. We also introduce amplified error sequences to optimize the accuracy. Furthermore, we show a definitive improvement in parallel gate operations with crosstalk cancellation, demonstrating the technique's effectiveness. This work paves the way for superconducting hardware that features automated calibration of microwave crosstalk, leading to enhanced fidelities in multiqubit circuits.

Moso bamboo is famous for fast growing and biomass accumulation, as well as high annual output for timber and bamboo shoots. These high outputs require high nutrient inputs to maintain and improve stand productivity. Soil nitrogen (N), phosphorus (P) and potassium (K) are important micronutrients for plant growth and productivity. Due to high variability of soils, analysing spatial patterns of soil N, P and K stocks is necessary for scientific nutrient management in Moso bamboo forests. In this study, soils were sampled from 138 locations across Yong’an City and ordinary kriging was applied for spatial interpolation of soil N, P and K stocks. Soil N stock showed a strong spatial dependence while soil N and P stocks presented a moderate spatial dependence, indicating soil N was mainly controlled by intrinsic factors while soil N and P stocks were controlled by both intrinsic and extrinsic factors. Different spatial patterns were observed for soil N, P and K stocks across the whole study area, indicating that fertilizations with different ratios of N:P:K should be applied for different sites to maintain and improve stand productivity. The total soil N, P and K stocks within 0-60 cm were 0.624, 0.020 and 0.583 Tg, respectively.

Spermatogenesis is critical for insect reproduction and is regulated by many different genes. In this study, we found that Forkhead transcription factor Fd59a functions as a key factor in spermatogenesis of Drosophila melanogaster. Fd59a contains a conversed Forkhead domain, and it is clustered to the FoxD subfamily with other FoxD members from some insect and vertebrate species. Mutation in Fd59a caused swelling in the apical region of the testis. More importantly, only a few mature sperm were present in the seminal vesicle of Fd59a mutant flies compared to the control flies, and the fertility of Fd59a2/2 mutant males was significantly lower than that of the control flies. Immunofluorescence staining showed that the homeostasis of testis stem cell niche in Fd59a2/2 mutant and Fd59a RNAi flies was disrupted, and apoptosis of sperm bundles was increased. Furthermore, results from RNA-sequencing and qRT-PCR suggest that Fd59a can regulate expression of genes related to reproductive process and cell death. Taken together, our results indicated that Fd59a plays a key role in the spermatogenesis of Drosophila.

Many types of banana (Musa spp.)—one of the most economically important horticultural crops—exist, and their ploidy (diploid, triploid, and tetraploid, usually) and genome types (containing A or/and B genome in most cases) differ. At present, observation and genome type detection are commonly used to identify banana germplasm resources. However, the former is tedious, while the latter cannot distinguish categories below genome types. It is therefore urgent that a simple and effective method for identifying banana germplasm resources is established. We sequenced and analyzed the ribosomal DNA internal transcribed spacer (ITS) sequences of 62 banana germplasm and found that the sequencing peaks, especially the 20 bp region near the 420 bp position (referred to as the “420 bp region”), exhibited relatively recognizable and repeatable polymorphism characteristics. Using the “420 bp region” as a marker, we were able to quickly distinguish bananas belonging to different genome type groups (comprising the AA, AB, AAA, ABB, AAB, ABBB, AAAB, and AAAA groups) or different subgroups in the same genome type group (for example, the Cavendish, Gros Michel, Red, Lakatan, and Ibota Bota subgroups in the AAA group; and the Pisang Raja, Plantain, Pome and Silk subgroups in the AAB group). Moreover, it appeared that Sanger sequencing of ITS could be used for identifying banana hybrid offspring. These results demonstrated that the banana ITS region contains rich genetic information that is useful for genotyping. In general, ITS sequencing simplifies the classification of banana germplasm resources and has potential application in several areas of Musa improvement.

As a new type of high-performance material, gradient structural steel is widely used in engineering fields due to its unique microstructure and excellent mechanical properties. For the prevalent fatigue failure problem, the rate of change of the local grain size gradients along the structure (referred to as the gradient rate) is a key parameter in the design of gradient structures, which significantly affects the fatigue performance of gradient structural steel. In this work, a method of ‘Voronoi primary + secondary modeling’ is adopted to successfully establish three typical high-strength steel models corresponding to the convex, linear, and concave type gradient rates for gradient structures, focusing on the stress-strain response and crack propagation in structural steel with different gradient rates under cyclic loading. It is found that the concave gradient rate structural model is dominated by finer grains with larger volume fraction, which is conducive to hindering fatigue crack propagation and has the longest fatigue life; the linear structure is the second one, and the convex structure is the shortest one. The simulation results in this work are consistent with the relevant experimental phenomena. Therefore, when regulating the gradient rate, priority should be given to increasing the volume fraction of fine grains and designing a gradient rate structure dominated by fine grains to improve the fatigue life of the material.

Marine sand, in addition to oil and gas resources, is the second largest marine mineral resource. The rational development and utilization of marine sand resources are conducive to the growth of the marine economy. Marine sand can be categorized into surface marine sand and buried marine sand. Buried marine sand deposits are buried beneath the sea floor, making it challenging to locate them due to their thin distribution. Consequently, there exist numerous technical difficulties associated with marine sand exploration. In this study, various geophysical methods such as sub-bottom profile survey and single-channel seismic survey were employed in the northern offshore waters of the South China Sea along with offshore engineering geological drilling. As a result, two distinct marine sand bodies were delineated within the study area. Additionally, five reflective interfaces (R0, R1, R2, R3 and R4) were identified from top to bottom. These interfaces can be divided into five seismic sequences: A2, B2, C2, D2 and E2 respectively. Three sets of strata were recognized: the Quaternary Holocene Marine sedimentary layer (Q4m), the Upper Pleistocene alluvial layer, and the diluvial sedimentary layer (Q3al+pl) as well as the Upper Pleistocene Marine sedimentary layer (Q3m). Sequence A2 and B2 corresponded to Quaternary Holocene Formation (Q4m) within the study area while sequence C2 corresponded to B2 as well as upper Pleistocene alluvial and alluvial deposits (Q3al+pl), which represent one of the main occurring layers of sand in this region. Lastly, E2 represents a layer composed mainly of silty clay and round gravel known as upper Pleistocene marine sediment layer (Q3m). In total, two ore bodies containing marine sand have been discovered during this study. The estimated total resource amounts approximately 46 million m³ with an average thickness around 11 meters.

Abiotic stress, especially drought stress poses a significant threat to the terrestrial plant growth, development, and productivity. Although mulberry have great genetic diversity and extensive stress tolerant traits in agroforestry systems, only a few reports offer preliminary insight into biochemical responses of mulberry leaves under drought conditions. In this study, we performed a comparative metabolomic and transcriptomic analysis on the “drooping mulberry” (Morus alba var. Pendula Dippel) under PEG-6000-simulated drought stress. Our research revealed that drought stress significantly enhanced flavonoid accumulation and up-regulated the expression of phenylpropanoid biosynthetic genes. Furthermore, the activities of superoxide dismutase (SOD), catalase (CAT) and malondialdehyde (MDA) content were elevated. In vitro enzyme assays and fermentation tests indicated the involvement of flavonol synthase/flavanone 3-hydroxylase (XM_010098126.2) and anthocyanidin 3-O-glucosyltransferase 5 (XM_010101521.2) in the biosynthesis of flavonol aglycones and glycosides, respectively. The recombinant MaF3GT5 protein was found to recognize kaempferol, quercetin, and UDP-glucose as substrates, but not 3-/7-O-glucosylated flavonols and UDP-rhamnose. MaF3GT5 is capable of forming 3-O- and 7-O-monoglucoside, but not di-O-glucosides, form kaempferol. This implies its role as a flavonol 3, 7-O-glucosyltransferase. The findings from this study provided insights into the biosynthesis of flavonoids and could have substantial implications for the future diversified utilization of mulberry.

This study, conducted with meticulous attention to detail, comprehensively examines the state of plants and their adaptation to Kazakhstan's extra-arid climatic zone of the Mangistau. It uses the collections of woody plants from the Mangyshlak Experimental Botanical Garden in Aktau as a case study and extrapolates the results to the entire region. The study area is arid and unsuitable for many plants, so examining physiological adaptation mechanisms and strategies for preserving plants in unfavourable conditions is crucial. The study employed a range of methods, including the measurement of the intensity of transpiration, leaf hydration, and the content of chlorophyll A, B, and carotenoids. These methods were chosen for their proven effectiveness in similar studies and their ability to provide accurate and reliable data. The samples were also assessed using a point system for resistance to drought, phytophagy, gas tolerance, salt tolerance, winter hardiness, and soil fertility. The results obtained and entered into the IEBG platform “DinTseR” to assess the value of the introduction using a diagnostic scale revealed a high variability (up to 51.7-52.2%) of physiological indicators of growth and development. The highest values of transpiration intensity were observed in deciduous trees and shrubs, rose varieties (205-243 mg/g fresh leaf mass per hour), leaf water content - in climbing plants (68.9%), chlorophyll A and B content - in deciduous plants, and plants - old trees, fruit trees and varietal roses (3.46-3.93 and 1.34-1.84%). Their concentration in coniferous species is almost two times lower (0.63%). A correlation was also made between various significant factors. Twenty regression equations and forecasts have been identified that can be used to diagnose and assess resistance, thereby reducing the cost of determining the introduction value in the conditions of Mangistau. These findings are essential in understanding and preserving the unique flora of the Mangistau region.

Superior fiber quality is one of the most important objectives in cotton breeding. To detect the genetic basis underlying fiber quality, an F2 population containing 413 plants was constructed by crossing Jifeng 914 and Jifeng 173, both of which have superior fiber quality, with Jifeng 173 being better. Five fiber quality traits were investigated in the F2, F2:3, F2:4, and F2:5 populations. Quantitative trait loci (QTL) mapping was conducted based on a high-density genetic map containing 11,488 single nucleotide polymorphisms (SNPs) and spanning 4,202.12 cM in length. Transgressive segregation patterns and complex correlations in the five tested traits were observed. A total of 108 QTLs were found, including 27 for fiber length (FL), 16 for fiber strength (FS), 24 for micronaire (MC), 17 for fiber uniformity (FU), and 24 for fiber elongation rate (FE). Chromosome A7 contained 12 QTL, ranking the first. No QTL was found on chromosome D1 and D11. Each QTL contributed 1.98%–21.45% to the phenotypic variation (PV), including 13 major effect QTLs that contributed more than 10% toward PV. Two QTLs could be repeatedly detected in three populations, including qFL-D3-2 in F2, F2:4, and F2:5 with 9.18%–21.45% of PV, qFS-A11-1 in F2:3, F2:4 and F2:5 with 6.05%–10.41% of PV. Another seven stable QTLs could be detected in two populations, including four major effect QTLs: qFL-A12-3, qFS-D10-2, qMC-D6-2, and qMC-D8-1. Fourteen QTL-overlapping regions were found, which might explain the complex correlations among the five phenotypic traits. Four regions on chromosome A11, D3, D6, and D10 covered by both stable and major effect QTLs are promising for further fine mapping. The genomic regions of the two QTLs detected in three populations and the four major effect QTLs contain 810 genes. Gene functional analysis revealed that the annotated genes are mainly involved in protein binding and metabolic pathways. Fifteen candidate genes in the qFL-D3-2 region are highly expressed in fiber or ovules during fiber initiation, elongation, secondary cell wall thickening, or maturation stages. qRT-PCR revealed that Ghir_D03G005440.1 and Ghir_D03G011310.1 may play a role in promoting fiber initiation, Ghir_D03G006470.1 may be beneficial for promoting fiber elongation. This study provides more information for revealing the molecular genetic basis underlying cotton fiber quality.

Pyrops candelaria is one of the common pests of fruit trees, but the research on the pathogenic microorganisms it may carry is very limited. Therefore, it is essential to reveal the pathogenic microbes it carries and their potential hazards. This study found a new virus from the transcriptome of P. candelaria, which was first reported in P. candelaria and named as PyCaV (Pyrops candelaria associated virus). RACE and bioinformatics assay revealed that the full-length of PyCaV is 10855 bp with the polyA tail, containing a single open reading frame (ORF) encoding a polyprotein consisting of 3171 amino acid (aa). The virus has a typical Iflavirus structure, including two rhv domains, a RNA helicase domain (HEL), a 3C cysteine protease domain (Pro), and a RNA-dependent RNA polymerase domain (RdRp). Further phylogenetic analysis revealed that this virus belongs to family Iflaviridae and sequence alignements analysis suggedted PyCaV is new member in unassigned genus of family Iflaviridae. Further in-depth analysis of virus-infection-part showed that PyCaV is distributing in the whole longan lanternfly, including its head, chest, and abdomen, but more PyCaV was identified in the chest. The distribution of PyCaV in different parts of P. candelaria was further explored, which showed that more PyCaV were detected in its piercing-sucking mouthparts and chest viscera. Statistical analysis showed that the PyCaV infection was affected by time and locations.

The emergence of drug-resistant mycobacteria has rendered many clinical drugs and regimens ineffective, imposing significant economic and healthcare burden on individuals and society. Repurposing drugs intended for treating other diseases is a time-saving, cost-effective, and efficient approach for identifying excellent anti-mycobacterial candidates or lead compounds. This study is the first to demonstrate that rupatadine (RTD), a drug used to treat allergic rhinitis, possesses excellent activity against mycobacteria without detectable resistance, particularly Mycobacterium tuberculosis and Mycobacterium marinum, with a minimal inhibitory concentration as low as 3.13 µg/mL. Furthermore, RTD exhibited moderate activity against nonreplicating M. tuberculosis with the minimal inhibitory concentrations lower than drugs targeting the cell wall, suggesting that RTD has the great potential to be modified and used for the treatment of nonreplicating M. tuberculosis. Additionally, RTD exhibits partial synergistic effects when combined with clofazimine, pretomanid, and TB47 against M. tuberculosis, providing the theoretical foundation for the development of treatment regimens. Transcriptomic profiling leads us to speculate that eight essential genes may be the targets of RTD or may be closely associated with the mycobacterial resistance to RTD. In summary, RTD may be a promising hit for further anti-mycobacterial drug or regimen optimization, especially in case of nonreplicating mycobacteria.

As the most serious of the many worse new pathological changes caused by diabetes, there are many risk factors for the occurrence and development of DR. It mainly includes hyperglycemia, hypertension, hyperlipidemia and so on. Among them, hyperglycemia is the most critical cause, which plays a key role in the pathological changes of DR.High-sucrose diets(HSDs) lead to elevated blood glucose levels in vivo, which, through oxidative stress, inflammation, the production of AGEs and VEGF, causes plenty of pathological damages to the retina and ultimately bring about loss of vision. The existing therapies for DR primarily target the terminal stage of the disease, when irreversible visual impairment has appeared. Therefore, early prevention is particularly critical. Early prevention of DR-related vision loss requires adjustments to dietary habits, mainly by reducing sugar intake. This article primarily discusses the risk factors, pathophysiological processes, and molecular mechanisms associated with the development of DR caused by HSDs. It aims to raise awareness of the crucial role of diet in the occurrence and progression of DR, promote timely changes in dietary habits, prevent vision loss, and improve the quality of life. The aim is to make people aware of the importance of diet in the occurrence and progression of DR. According to the dietary modification strategies we give, patients can change their poor eating habits timely, avoid the retinopathy that can be avoided theoretically, and obtain a excellent outcome.

Two coupled climate models which participated the CMIP6 project (Coupled Model Intercomparison Project Phase 6), the Earth System Model of Chinese Academy of Sciences version 2 (CAS-ESM2-0) and the Nanjing University of Information Science and Technology Earth System Model version 3 (NESM3), were assessed in terms of the impact of four new sea ice parameterization schemes. These four new schemes are related to air-sea heat flux, radiation penetration and absorption, melt ponds, ice-ocean flux, respectively. To evaluate the effectiveness of these schemes, key sea ice variables with and without these new schemes, such as sea ice concentration (SIC) and sea ice thickness (SIT), were compared against observation and reanalysis product from 1980 to 2014. The simulations followed the design of historical experiments within the CMIP6 framework. The results revealed that both models demonstrated improvements in simulating Arctic SIC and SIT when the new parameterization schemes were implemented. The model bias of SIC in some marginal sea ice zones of Arctic was reduced, especially during March. The SIT was increased and the transpolar gradient of SIT was reproduced. The changes of spatial pattern of SIC and SIT after adding new schemes bear similarities between the two coupled models. This suggests that the new schemes have potential for broad application in climate models, especially for those with underestimated SIT.

Microwave technology has a potential application in the extraction of zinc from sulphide ores, knowledge of the dielectric properties of these ores plays a major role in the microwave design and simulation for any process. The dielectric properties of zinc sulfide concentrate for two different apparent densities—1.54 and 1.63 g/cm³—have been measured by using the resonance cavity perturbation technique at 915 and 2450 MHz during the roasting process for the temperature ranging from room temperature to 850 °C. The variations of dielectric constant, the dielectric loss factor, the dielectric loss tangent and the penetration depth with the temperature, frequency and apparent density have been investigated numerically. The results indicate that the dielectric constant increases as the temperature increases and temperature has a pivotal effect on the dielectric constant, while the dielectric loss factor has a complicated change and all of the temperature, frequency and apparent density have a significant impact to dielectric loss factor. Zinc sulfide concentrate is high loss material from 450 to 800 °C on the basis of theoretical analyses of dielectric loss tangent and penetration depth, its ability of absorbing microwave energy would be enhanced by increasing the apparent density as well. The experimental results also have proved that zinc sulfide concentrate is easy to be heated by microwave energy from 450 to 800 °C. In addition, the experimental date of dielectric constant and loss factor can be fitted perfectly by Boltzmann model and Gauss model, respectively.

This article presents the analysis of the allocation of important plant areas (IPA), which urgently identifies the most valuable sites for protecting plant objects. The study is based on a comprehensive inventory of the species composition of plants in the flora of the Western Karatau Ridge and the Mangyshlak Peninsula (arid regions)- key sites Akmysh, Samal, and Kogez, considered standard and the best preserved with natural vegetation cover. The flora of these critical sites was analysed using a combination of field surveys, herbarium studies, and a literature review. The results revealed a rich biodiversity, with 104 species from 82 genera and 33 families. Most species belong to 9 families, making up 60.6% of the total taxa. By the nature of life forms, perennial herbaceous plants dominate in all key sites (30 species, 50.0%). The eco-phylogenetic spectrum showed that a significant share of the flora of the studied IPAs is made up of xerophytes (21 species, 35%) and xeromesophytes (9 species, 15%); desert and mountain-steppe species prevail (53.0%). Rare, endangered and Red Book species account for 10-21.3% of those growing in the region. Regarding economic value, fodder, ornamental, honey, medicinal and food species dominate. The Shannon, Simpson, and Jaccard indices assessed alpha-beta and gamma diversity. The index showed that biodiversity in the Samal and Kogez sites is higher and more evenly distributed compared to the Akmysh site. The Whittaker, Harrison and Cody indices confirm significant differences in the species composition between the sites. In light of these compelling results, a clear and urgent call to action is proposed to allocate these areas to the IPA category, a crucial step towards ensuring the long-term existence of natural biocenoses.

The key links of face recognition are digital image preprocessing, facial feature extraction and pattern recognition, this article aimed at the current problem of slow speed and low recognition accuracy of face recognition , from the above three key links, on the basic of analyzing the therories of Fractional Differential Masks Operator (FDMO), Principal Component Analysis (PCA) and Support Vector Machine (SVM), design a kind of FDMO+PVA+SVM coupling algorithm that applies to face recognition to improve the speed and accuracy of it. To realize FDMO+PCA+SVM coupling algorithm, first, we should apply FDMO to face image processing binary marginalization, the purpose is getting face contour; Then, we apply PCA to get the feature of face image which is disposed by binary marainalization. At last, we can apply One-Against All of the SVM classifier and LibSVM software package to realize face recognition. Beside, the article with nine different coupling algorithm design four groups of experimental reaults on the ORL face database verified by comparative analysic FDMO+PCA+SVM coupling algorithm in the superiority of face recognition accuracy and speed.

To address the requirements of sonar imaging, such as high receiving sensitivity, wide bandwidth, wide receiving angle, an AlN PMUT with an optimized ratio of 0.6 for the piezoelectric layer diameter to backside cavity diameter is proposed in this paper. A sample AlN PMUT is designed and fabricated with SOI substrate-based bulk MEMS process. The characterization test result of the sample demonstrates a -6 dB bandwidth of approximately 500 kHz and a measured receiving sensitivity per unit area of at 1.37 V/μPa/mm2, which significantly surpasses the performance of previously reported PMUTs. The -6 dB horizontal angles of the AlN PMUT at 300 kHz and 500 kHz are measured 68.30° and 54.24°, respectively. To achieve an accurate prediction of its characteristics when being packaged and assembled in a receive array, numerical simulations with the consideration of film stress are conducted. The numerical result shows a maximum deviation of ±7% in the underwater receiving sensitivity across the frequency range of 200 kHz to 1000 kHz and a deviation of about 0.33% in the peak of underwater receiving sensitivity comparing to the experimental data. By such good agreement, the simulation method reveals its capability of providing theoretical foundation for enhancing the uniformity of the AlN PMUTs in future studies.

Acting as the most abundant and widely distributed volatile secondary metabolites in plants, terpenoids play crucial roles in diverse physiological regulations and metabolic processes. Terpene synthases occupy a decisive proportion in determining the composition and diversity of terpenoids; though their regulatory effects have been extensively investigated across various plant species, limited studies have focused on the upstream transcriptional regulation of terpene synthases. In this study, we unveil linalool as the predominant volatile compound in Freesia hybrida flowers, demonstrating a gradual release pattern during flower blooming. In the context of the transcriptome, a typical MYB transcription factor, FhMYB108, was screened based on digital expression profile correlation analysis and homologous gene comparison. FhMYB108 is capable of regulating the expression of terpene synthase FhTPS1, and both their expression levels exhibit a gradual increase concomitant with flower opening. Moreover, transcriptional regulation and transient expression assays revealed that FhMYB108 exerts a stimulatory effect on the transcription of A. thaliana AtTPS14, while no significant increase in AtTPS14 expression was observed upon stabilization of FhMYB108 in Arabidopsis. Investigate its reason, the highly expressed AtMYC2 in A. thaliana can interact with FhMYB108 to suppress the activation of AtTPS14 by FhMYB108. The present study not only elucidated the regulatory mechanism underlying linalool synthesis, but also discovered the synergistic effect of MYB and bHLH transcription factors in governing the biosynthesis of volatile terpenoids.

Malaria parasites increase their host erythrocyte’s permeability to obtain essential nutrients from plasma and facilitate intracellular growth. In the human P. falciparum pathogen, this increase is mediated by the plasmodial surface anion channel (PSAC) and has been linked to CLAG3, as encoded by one member of the conserved clag multigene family. Whether paralogs encoded by other clag genes also contribute to PSAC formation or serve unrelated roles remains unknown. Here, we generated transfectant lines carrying epitope-tagged versions of each CLAG. Each paralog colocalized with CLAG3, with concordant trafficking via merozoite rhoptries to the host erythrocyte membrane of newly-invaded erythrocytes. Each also exists within infected cells in at least two forms: an alkaline-extractable soluble form and a form integral to the host membrane. Like CLAG3, CLAG2 has a variant region cleaved by extracellular protease but CLAG8 and CLAG9 are protease-resistant. Paralog knockout lines, generated through CRISPR/Cas9 transfection, exhibited uncompromised growth in PGIM, a modified medium with more physiological nutrient levels; this finding is in marked contrast to a recently reported CLAG3 knockout parasite. CLAG2 and CLAG8 knockout lines exhibited compensatory increases in transcription of remaining clags and associated rhoph genes, yielding increased PSAC-mediated uptake to specific solutes. We also report distinct transport properties of these knockout lines, suggesting partially overlapping roles of CLAG paralogs in PSAC activity. We propose that the nutrient channel pore is formed by a higher order assembly of CLAG proteins at the host membrane.

Health-Related Quality of Life (HRQoL) encompasses the comprehensive evaluation of an indi-vidual's health and well-being across multiple dimensions. Mindfulness, recognized as a scientifi-cally supported strategy for anxiety management, plays a role in enhancing both physical and mental health. The Gut-Brain Axis (GBA) serves as the bidirectional communication link between the gastrointestinal system and the central nervous system. This study aims to explore the associa-tion between Mindfulness and factors influencing the GBA in both healthy individuals and those with Inflammatory Bowel Diseases (IBD). A cross-sectional investigation involved 338 adults, in-cluding 50 IBD patients, utilizing validated Greek scales for Mindfulness (MAAS-15), Mediterra-nean Diet (14-MEDAS), and HRQoL (EQ-5D-5L). The questionnaire gathered demographic, an-thropometric, and lifestyle data. Among healthy participants, EQ-5D-5L showed a moderate cor-relation with the MAAS-15 scale (r=0.389, p

Lean body mass (LBM) is correlated with powerlifting performance in athletes competing in different bodyweight classes. However, it remains unknown whether changes in LBM are correlated with performance changes in powerlifters preparing for a competition. Aim of the study was to investigate the changes in LBM and performance in powerlifters preparing for a competition. Eight male powerlifters (age 31.7±9.8years, height 1.77±0.06m, weight 99.2±14.6kg) and three female powerlifters (age 32.7±16.3years, height 1.54±0.06m, weight 66.6±20.9kg), participated in the study. Athletes followed individualized periodized training programs for 12 weeks aiming to maximize their performance for the national championship. Maximum strength (1-RM) in squat, bench press, and deadlift, body composition, grip strength, anaerobic power, quadriceps’ cross sectional area and vastus lateralis muscle architecture were measured before and after the training period. Significant increases were found after the training period in squat (5.8±7.0%, P

Carotid atherosclerotic lesions are a major cause of cerebrovascular disease (CVD). Identification and quantification of carotid plaques are important for categorizing the vulnerability of plaques for rupture and assessing the impact of treatments. The irregularity of plaque surface is associated with previous plaque rupture and plays an important role in the risk of stroke. Thus, the aim of this study is to develop and validate novel vulnerability biomarkers from three-dimensional ultrasound (3DUS) images by analyzing the surface morphological characterization of carotid plaque using fractal geometry features. 3D box-counting and 3D blanket are the two types of 3D fractal dimension that were employed to describe the smoothness of plaques. This fractal dimension analysis tool was used to evaluate the effect of atorvastatin using 3DUS carotid images, which were acquired from 6 patients treated with atorvastatin with 80 mg daily and 5 patients with placebo. The Student's T Test results showed that those two fractal features were effective for detecting the statin-related changes in carotid atherosclerosis with p<0.0068 and p<0.015 respectively, suggesting that 3D fractal dimension measurements can be used effectively to analyze the surface characteristics of carotid plaques, especially for evaluating the impact of the treatment.

With continuous increase in integration of the semiconductor devices, the requirements on size accuracy and surface quality of the etched lead frame are higher. The etchant is a key factor on etching process and etched surface quality, while effects of the difference in etchants on microscopic etched surface morphology of the Cu alloy have not been directly studied. In this study, the aqua regia, acidic FeCl3 and CuCl2 solutions were used as etchants, and the CuCrSn alloy specimens with different microstructure were etched and characterized. The results show that the etching rate in aqua regia is high, and the grain orientation, grain boundary (GB) and dislocation have significant influence on the local etching rate. The preferential etching of some atomic planes forms steps between grains with different orientations, and the preferential etching around the GB and dislocation group forms grooves, resulting in high surface roughness. For etching of the FeCl3 and CuCl2 etchants, the steps and grooves become blurred, and almost invisible on the surface etched by the CuCl2 etchant, thus the surface roughness is much lower. The CuCrSn alloy surface etched by the aqua regia is clean, with little Cr-rich particles, while high density Cr-rich particles are remained on the surfaces etched with the FeCl3 and CuCl2 etchants. For the same kind of etchant, the ion concentration can affect the etching mechanism and etching surface morphology.

The B169L protein (pB169L) of African swine fever virus (ASFV) is a structural protein with an unidentified function during the virus replication. The sequences of the B169L gene and the downstream B438L gene are separated by short intergenic regions. However, the regulatory mode of the gene transcription remains unknown. Here, we identified two distinct promoter regions and two transcription start sites (TSS) located upstream of the open reading frame (ORF) of B438L. Using the promoter reporter system, we demonstrated that the cis activity of the ORF proximal promoter exhibited significantly higher levels compared with that of the distal promoter located in the B169L gene. Furthermore, transfection with the plasmids with two different promoters for B438L could initiate the transcription and expression of the B438L gene in HEK293T cells, and the cis activity of the ORF proximal promoter also displayed the higher activities compared with the distal promoter. Interestingly, the B438L distal promoter also initiated the transcription of the alternatively spliced B169L mRNA (B169L mRNA2) encoding a truncated pB169L (tpB169L) (amino acids 92–169), and the gene transcription efficiency was increased upon mutation of the initiation codon located upstream of the alternatively spliced B169L gene. Taken together, we demonstrated that the distal promoter of B438L gene initiates the transcription of both the B438L mRNA and B169L mRNA2. Comprehensive analysis of the transcriptional regulatory mode of the B438L gene is beneficial for the understanding of the association of B438L protein and pB169L and the construction of the gene-deleted ASFV.

Hydraulic fracturing in shale gas reservoirs has usually resulted in complex fracture network. The results of micro-seismic monitoring showed that the nature and degree of fracture complexity must be clearly understood to optimize stimulation design and completion strategy. This is often called stimulated reservoir volume (SRV). In the oil & gas industry, stimulated reservoir volume has made the shale gas exploitation and development so successful, so it is a main technique in shale gas development. The successful exploitation and development of shale gas reservoir has mainly relied on some combined technologies such as horizontal drilling, multi-stage completions, innovative fracturing, and fracture mapping to engineer economic completions. Hydraulic fracturing with large volumes of proppant and fracturing fluids will not only create high conductivity primary fractures but also stimulate adjacent natural fractures. Fracture network forming around every hydraulic fracture yields a stimulated reservoir volume. A model of horizontal wells which was based on a shale gas reservoir after volume fracturing in China was established to analyze the effect of related parameters on the production of multi-fractured horizontal wells in this paper. The adsorbed gas in the shale gas reservoir is simulated by dissolved gas in the immobile oil. The key to simulate SRV is to accurately represent the hydraulic fractures and the induced complex natural fracture system. However, current numerical simulation methods, such as dual porosity modeling, discrete modeling, have the following limitations: 1) time-consuming to set up hydraulic and natural fracture system; 2) large computation time required. In this paper, the shape of the stimulated formation is described by an expanding ellipsoid. Simplified stimulated zones with higher permeability were used to model the hydraulic fracture and the induced complex natural fracture system. In other words, each primary fracture has an enhanced zone, namely SRV zone. This method saves much developing fine-grid time and computing time. Compared with the simulation results of fine-grid reference model, it has shown that this simplified model greatly decreases simulation time and provides accurate results. In order to analyze the impacts of related parameters on production, a series of simulation scenarios and corresponding production performance were designed. Optimal design and analyses of fracturing parameters and the formation parameters have been calculated in this model. Simulation results showed that the number of primary fractures, half length, SRV half-width and drop-down have great effects on the post-fracturing production. Formation anisotropies also control the production performance while the conductivity of the primary fractures and SRV permeability do not have much impact on production performance. The complexity of stimulated reservoir volume has strong effect on gas well productivity. Fracture number mainly affects the early time production performance. The increase of SRV width cannot enlarge the drainage area of the multi-fractured horizontal wells, but it can improve the recovery in its own drainage region. Permeability anisotropies have much effect on production rate, especially the late time production rate. The results prove that horizontal well with volume fracturing plays an irreplaceable role in the development of ultra-low permeability shale gas reservoir.

The mechanism underlying microbiologically induced carbonate precipitation have not been thoroughly characterized, although numerous scholars and experts have specifically investigated questions regarding minerals induced by bacteria. The study of the precipitation of carbonate minerals induced by halophilic bacteria has aroused wide concern. The present study aimed to investigate the characterization and process of biomineralization in high salt systems by a halophilic bacterium, Chromohalobacter israelensis strain LD532 (GenBank: KX766026), which was isolated from the Yinjiashan Saltern in China. Carbonate minerals induced by LD532 were investigated in several sets of comparative experiments that employed magnesium sulfate and magnesium chloride as Mg resources. Magnesium calcite and aragonite were induced by LD532 bacteria, whereas these minerals did not appear in the control group. The mineral phases, micromorphologies, and crystal structures were analysed using X-ray powder diffraction, scanning electron microscopy, and energy dispersive X-ray detection. The carbonic anhydrase and urease secreted by strain LD532 through metabolism increased the pH value of the liquid medium and promoted the process of carbonate precipitation. Further study using high resolution transmission electron microscopy, energy dispersive X-ray detection and analysis of ultrathin slices showed that the nucleation sites of carbonate minerals were located on extracellular polymeric substances and the membranes of intracellular vesicles of LD532 bacteria, which provided favourable conditions for the growth of carbonate mineral crystals. The morphologies and compositions of minerals formed in solutions of MgSO₄ and MgCl₂ display significant differences, indicating that different sources of Mg²⁺ may also affect the physiological and biochemical activities of microorganisms and thus mineral deposition. This study will be of some interest for the interpretation of carbonate biomineralization in natural salt environments and has some value as a reference in understanding sedimentary carbonates in ancient marine environments, such as tidal flats.

The aim of this study was to examine the oxidation of human serum albumin (HSA) caused by oxidative stress after an exhaustive exercise such as ultra-marathon race. Thus, blood samples from 12 adult runners who underwent a 103 km mountain ultra-marathon race were collected pre- and 24, 48 and 72 h post race. HSA was partially purified using affinity chromatography and then was subjected to Western blot analysis for disulfide dimers determination, indicating oxidation. The results were correlated with those from a previous study in which the same samples were analyzed using different oxidative stress markers and a good correlation with protein carbonyls (PC) at all time points was observed. Moreover there was a significant correlation with static oxidation-reduction potential (sORP) at 24 h, and a negative correlation with capacity oxidation-reduction potential (cORP) at 24 and 48 h. In addition, an individual analysis of albumin dimers exhibited great inter-individual differences. This inter-individual variability in the oxidation of HSA may suggest different interventions (e.g. through diet) in order to confront the effects on athletes’ organism after a strenuous exercise. In conclusion, this study supported the importance of the assessment of albumin dimers as a predictive marker for exercise-induced oxidative stress.

Studying models of healthy aging and exceptional longevity is crucial to understand a possible longevity signature as most of them show resistance to age-related diseases. In particular, semi- and supercentenarians are a highly selected group, having survived significant adversities, including the Spanish Flu and COVID-19 pandemics, indicating distinctive immune system characteristics. This paper analyse the inflammatory scores (INFLA-score, Systemic Inflammation Response Index (SIRI)) and Aging-Related Immune Phenotype (ARIP) indicators calculated from the dataset of the DESIGN project, including 249 participants aged 19-111 years, trying to understand the immune-inflammatory (IMFLAM) role to achieve longevity. Statistical analyses, including linear regression and one-way ANOVA, were performed to explore the correlations between these parameters and age. Both INFLA-score and SIRI showed a significant increase with age. However, no statistical difference is observed when analysing the values for semi- and supercentenarians with those for other age groups, whose values are similar to that of adults and less than younger centenariansRegarding ARIP values, it is noteworthy that when comparing the CD8 Naive/Effector scores between groups, no significant differences were observed between the semi- and supercentenarian group and the other groups. These results support the idea that the control of IMFLAM response can promote extreme longevity.

With advancements in digital technologies such as 5G communications, big data, and cloud computing, the components of network operation systems have become increasingly complex, significantly complicating system monitoring and maintenance. Correspondingly, automated log anomaly detection has become a crucial means to ensure stable network operation and protect them from malicious attacks or failures. Conventional machine learning and deep learning methods assume consistent distributions between the training and testing data, adhering to a closed-set recognition paradigm. Nevertheless, in realistic scenarios, systems may encounter new anomalies that were not present in the training data, especially in log anomaly detection. Inspired by evidential learning, we propose a novel anomaly detector called LogEDL, which supervises training of the model through an evidential loss function. Unlike traditional loss functions, the evidential loss function not only focuses on correct classification, but also quantifies the uncertainty of predictions. This enhances the robustness and accuracy of the model in handling anomaly detection tasks, while achieving functionality similar to open-set recognition. To evaluate the proposed LogEDL method, we conduct extensive experiments on three datasets, i.e., HDFS, BGL, and Thunderbird, to detect anomalous log sequences. Experimental results demonstrate that our proposed LogEDL achieves state-of-the-art performance in anomaly detection.

The sexual reproduction of ascomycetes is controlled by the mating-type(MAT) locus. (Pseudo)homothallic reproduction has been hypothesized based on genetic data from Hirsutella sinensis (Genotype #1 of Ophiocordyceps sinensis). In this study, the differential occurrence of the mating-type genes in the MAT1-1 and MAT1-2 idiomorphs, which constitute the genetic control of O. sinensis reproduction, was analyzed in 237 strains and 5 genomes of H. sinensis. The mating-type genes were differentially transcribed in H. sinensis Strain L0106, and the MAT1-2-1 transcript in H. sinensis Strain 1229 was alternatively spliced, with an unspliced intron I containing stop codons; these findings constitute O. sinensis reproduction controls at the transcriptional and coupled transcriptional-translational levels. The occurrence of the mating-type genes and a-/α-pheromone receptor genes differed among the 5 H. sinensis genomes. The differential occurrence and transcription of these genes are inconsistent with self-fertilization under (pseudo)homothallism but suggest self-sterility of H. sinensis, which therefore needs a mating partner to achieve sexual outcrossing under heterothallism or hybridization. Consistent occurrence and transcription of the mating-type genes of both the MAT1-1 and MAT1-2 idiomorphs have been reported in natural and cultivated Cordyceps sinensis, but these findings are insufficient to determine the reproduction mode(s) because of the co-occurrence of >90 fungal species and multiple genomically independent genotypes of O. sinensis. The mutant MAT1-1-1 and α-pheromone receptor transcripts in natural C. sinensis result in the N-terminus or middle-truncated proteins, with changes in hydrophobicity and secondary structures of the proteins, suggesting heterogeneous fungal source(s) of the proteins and hybridization reproduction.

As critical biocontrol agents, Trichoderma and Metarhizium have demonstrated vast potential in disease prevention and pest control respectively. Current applications, however, are predominantly confined to singular use or simplistic combinations of the two fungi. This study innovatively utilizes Metarhizium and Trichoderma as experimental subjects, employing non-targeted metabolomics to compare the differences in metabolites between co-culture and separate fermentation. The metabolite distinctions in co-culture are meticulously analyzed using sample correlation, least squares discriminant analysis, cluster analysis, and KEGG enrichment analysis. Metabolome sequencing analysis is then applied to compare the co-culture fermentation filtrate with Trichoderma atroviride and Metarhizium anisopliae. Differential metabolite analysis found that co-culture had significantly up-regulated or down-regulated metabolites compared to singular cultures.However,significant metabolite discrepancies are discovered in singular cultures, notably the up-regulated metabolites such as osthole and spirocyclic amine, which have documented antibacterial functions that may prove effective against Fusarium graminearum. Ultimately, the findings from this research contribute to the exploration of synergistic applications of biocontrol fungi and serve as a valuable reference for future development of bio-pesticides for disease and pest control.

Apis mellifera, especially weak ones, are highly vulnerable to Carpoglyphus lactis mites, which can rapidly infest and consume stored pollen, leading to weakened colonies and potentially colony collapse. This study aimed to ascertain and investigate the prevalence of this mite in honeybee colonies across 9 provinces in the Republic of Korea (ROK). A total of 615 honeybee colonies were collected, from 66 apiaries during the spring and 58 apiaries during the summer of 2023. A 1,242 bp segment of the the Cytochrome c oxidase subunit 1 (COI) gene was amplified using the polymerase chain reaction method. The detection levels of C. lactis in the honeybees were compared between winter and summer. Based on the COI sequence analysis, the nucleotide sequence similarity of C. lactis mites isolated in the ROK with those from China (NC048990.1) was found to be 99.5%, and with those from the United Kingdom (KY922482.1) was 99.3%. This study is the first report of C. lactis in Korean apiaries. The findings in this study demonstrate a significantly higher detection rate in winter, which is 4.1 times greater than that in summer (p &lt; 0.001). Furthermore, the results underscore the usefulness of molecular diagnostic techniques for detecting C. lactis mites.

Bacillus subtilis is a model organism used to study molecular processes in Gram-positive bacteria. Sigma factor B, which associates with RNA polymerase, is one of the transcriptional regulators involved in the cell’s response to environmental stress. Experiments have proven that the amounts of free σB (SigB) are controlled by a system of anti- (RsbW) and anti-anti-sigma (RsbV) factors expressed from the same operon as SigB. Moreover, the phosphorylation state of RsbV is controlled by phosphatases RsbP and RsbU, which directly dephosphorylates RsbV. A set of chemical equations describing the network controlling the levels of free SigB was converted to a set of differential equations quantifying the dynamics of the network. The solution of these equations allowed the simulation of the kinetic behavior of the network and its components under real conditions. In this study, the time series of protein expression measured by mass spectrometry were utilized to investigate the role of the phosphatases RsbU/RsbP in transmitting the environmental signal. Additionally, the influence of kinetic constants and the amounts of other network components on the functioning of the network was investigated. A comparison with the same simulation performed using transcriptomic dataset showed that while the time series between the proteomic and transcriptomic datasets) are not correlated, the results are the same. This indicates that when modeling is done within one dataset, it does not matter whether the data come from the mRNA or protein level. In summary, the computational results based on experimental data provide quantitative insight into the functioning of the SigB-dependent circuit and offer a template for the quantitative study of similar systems.

Background: People with Down syndrome (DS) have a trisomy of chromosome 21 and marked deficits in verbal memory but relatively preserved visuospatial perception. Verbal memories are related to semantic knowledge. Little is known about the organization of semantic knowledge in people with DS, which was the aim of this study. Aims: The extent of false memory in people with DS was examined. Possible differences in the number of false memories induced by nominal and verbal themes were examined. Methods and Procedures: In the study phase, ten word lists with semantically related associates were presented. In the recognition phase, participants made judgments on whether each word had been represented previously as semantically related lures, old words, and semantically unrelated new words. Outcomes and Results: Differences in the processing of nominal and verbal theme-related lures were observed among people with DS. When processing nominal theme-related lures, people with DS showed delayed false positives. When processing verbal theme-related lures, people with DS showed no differences compared to controls. Similar patterns have been observed in people with DS when processing nominal theme-related associates and verbal theme-related associates. People with DS have delayed recognition of associates. When processing unrelated words, they showed significantly higher false positives than controls for both nominal and verbal eliciting themes. Further analyses of the themes revealed differences in false positives across syntactic categories among groups. Conclusions and Implications: People with DS showed a delayed recognition of associates and deviance in recognizing unrelated words in the nominal and verbal theme categories. People with DS were delayed in terms of nouns, but deviated with verbs in associated and unrelated words. Additionally, people with DS showed distinct patterns in processing five nominal lures and three verbal lures, suggesting that they formed false memories differently based on distinct syntactic categories. Thus, it was concluded that people with DS develop a deviant semantic structure. Category-based interventions for people with DS should be implemented in order to improve their semantic knowledge through lexical connections.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

Small peptides (SPs), ranging from 5 to 100 amino acids, play integral roles in plants due to their diverse functions. Despite their low abundance and small molecular weight, SPs intricately regulate critical aspects of plant life, including cell division, growth, differentiation, flowering, fruiting, maturation, and stress responses. As vital mediators of intercellular signaling, SPs have garnered significant attention in plant biology research. This comprehensive review delves into SPs' structure, classification, and identification, providing a detailed understanding of their significance. Additionally, we summarize recent findings on the biological functions and signaling pathways of prominent SPs that regulate plant growth and development. The review also offers a forward-looking perspective on future research directions in peptide signaling pathways.

Abstract: Toxicity of emerging organic pollutants to photosystems of aquatic plants are still not well clarified. This study aimed to develop a novel ecotoxicological experimental protocol based on nanoscale electrochemical mapping of photosynthetic oxygen evolution of aquatic plants by SECM (scanning electrochemical microscopy). The protocol was also checked by confocal laser scanning microscopy (CLSM), the traditional Clark oxygen electrode method and chlorophyll fluorescence technique. The typical persistent organic pollutant 2,4-dichlorophenol (2,4-DCP) in water environment and the common aquatic Microsorium pteropus (M. pteropus) were chosen as the model organic pollutant and tested plant, respectively. It was found that the SECM method could well discriminated the responses of stoma micromorphology and spatial pattens of photosynthetic oxygen evolution on single stoma. The shape of stoma blurred with increasing 2,4-DCP concentration, which was in good agreement with the CLSM images. The dose-response curves and IC50 values obtained from the SECM data were verified by the data measured by the traditional Clark oxygen electrode method and chlorophyll fluorescence test. The IC50 value of single stoma oxygen emission of 24 h exposed plant leave, which was derived from the SECM current data (32535 μg L-1), was close to those calculated from the maximum photosynthetic efficiency (Fv/Fm) measured by chlorophyll fluorescence test (33963 μg L-1), and the Clark oxygen electrode method photosynthetic oxygen evolution rate (32375 μg L-1). The 72 h and 96 h 2,4-DCP exposure data further confirmed the reliability of the nanoscale stoma oxygen emission mapping methodology for ecotoxicological assessment. In this protocol, the procedures for how to collect effective electrochemical data and how to extract useful information from the single stoma oxygen emission pattern were well established. This study showed that SECM is a feasible and reliable ecotoxicological tool for evaluation of toxicity of organic pollutants to higher plants with unique nanoscale visualization advantage over the conventional methods.

In the contemporary accelerated pace of life, emphasizing the importance of sleep quality is essential for enhancing overall well-being and health. This study investigates the link between poor sleep quality and key factors affecting wellness, such as mental health and eating disorders. Through a cross-sectional analysis involving 407 participants, utilizing established measures including the Depression Anxiety Stress Scale (DASS-21), the Eating Disorder Examination Questionnaire Short (EDE-QS), and the single-item Sleep Quality Scale (SQS), data was collected and analyzed using SPSS v28 and R-Statistics. The findings reveal a significant correlation (p&lt;0.05) between DASS-21, EDE-QS, and SQS, indicating that individuals experiencing poor sleep quality exhibit higher levels of depression, anxiety, and stress. Furthermore, multinomial logistic regression analysis highlights low sleep quality as a risk factor for both mental health (OR: 1.071, 95% CI: 1.042, 1.102, p&lt;0.05, low vs. high sleep quality), and eating disorders (OR: 1.047, 95% CI: 1.004, 1.092, p&lt;0.05, low vs. high sleep quality). Overall, these results underscore the critical role of sleep quality in mental health and suggest insomnia as a predictive factor for both poor mental well-being and disordered eating habits. Further research through randomized controlled trials is warranted to validate the findings of this cross-sectional study.

The attitude dynamics and orbit dynamics of large rigid space structures are coupled with each other under gravity gradient, which may affect the stability of the large rigid space structures. In this paper, the gravity gradient stability of a large rigid space structure is studied under both small and large disturbances. Based on the rigid body dynamics and orbit dynamics, an accurate dynamic model without any linearization of the large rigid space structure is established via the natural coordinate formulation (NCF), which is able to describe the large overall motions of the structures. By using the generalized-α algorithm, the gravity gradient stability of the large rigid space structure is simulated and analyzed via various examples, including the influence of large disturbance angles, the positions at the stabilization and unstabilization regions. Finally, the relationship between spinning stability and gravity gradient stability is also investigated via a large spinning space structure.

the close phylogenetic relationship between ascidians (Tunicata) and vertebrates makes them a powerful model for studying the innate immune system. To better understand the nature and dynamics of immune responses and the mechanisms through which bacterial infections are detected and translated into inflammation in Ciona robusta, we applied an approach combining in vivo lipopolysaccharide (LPS) stimulation, immune-labelling and functional enzymatic analyses. The immunohistochemistry showed that toll-like receptor 4 (TLR4) and nuclear factor kappa B (NFκB) were expressed during the inflammatory pharynx response 4 hours post-LPS, with formation of immune-stained haemocyte nodules in the vessel lumen. Pharynx vessel endothelium also took part in the inflammatory response. Observations of histological sections from naive and MS-inoculated ascidians confirmed immuno-positive tissue response. Enzyme immune parameters – which included the activity of phenoloxidase, glutathione peroxidase, lysozyme, alkaline phosphatase and esterase – showed up-modulation 4 hours after LPS injection, confirming their involvement during ascidian inflammatory response. These findings provide new insights into the mechanisms involved in LPS-induced C. robusta response and suggest that a broad innate immune mechanism is involved in the regulation of tunicate inflammatory responses.

In recent years the number of available chemical pesticides has been significantly reduced and there have been an urgent need for discovery of alternative to chemical pesticides products, as among others the natural zeolites (zeolitic rocks). We determined the mineralogical and chemical composition of a specific and continuous layers of zeolitic rock sample (ZeotP) from Petrota, Ev-ros, Greece and evaluated its oviposition deterrent effect for the olive fruit fly Bactrocera oleae (Diptera: Terphritidae). The tested natural zeolite contained 70 wt. % Clinoptilolite, 18 wt. % Amorphous material, 7 wt. % Feldspars, 4 wt. % Cristobalite and 1 wt. % Quartz. We tested the oviposition deterrent effect of ZeotP mixed or not with an emulsifier adjuvant NU-FILM-P® in water and applied on the surface of olive fruits. The ZeotP oviposition deterrent effect for the ol-ive fly was very high under a series of tested temperatures (17°C, 20°C, 25°C and 30°C) and RHs (23%, 33%, 55%, 75%, 94%). In addition, the ZeotP residual deterrent effect after equable water spraying was high and similar to the respective effect of a pyrethroid insecticide (Decis®). Our results may contribute to an effective control of the olive fruit fly using an alternative to chemical pesticides natural zeolite (zeolitic rocks) product.

Using numerical simulation method, combined with the pre-branch material characteristics of the measurement results, based on the LS-DYNA software to simulate the branch crushing process, the analysis found that not only the existence of the cutter cutting in the branch destruction process, there is also the cutting of the opposing surface of the bending fracture, with the increase in the speed of the knife rollers, the cutter cutting resistance increases, the cutting resistance reaches 2690 N when the cutter at 2500 r/min, the cutter cutting resistance is the smallest in the cutting simulation at the blade angle of 55°, the blade angle is more suitable for the cutting of the branch. In the cutting simulation under different cutting edge angles, the cutting resistance of the tool is the smallest when the edge angle is 55°, which is 1860 N. This edge angle is more suitable for branch crushing and cutting. Using Fluent software to analyse the airflow characteristics of the crushing device, it was found that with the increase of the knife roller speed, the inlet flow and negative pressure of the crushing chamber are increasing, the speed of 2500 r/min, the inlet flow and negative pressure were 1.92 kg/s and 37.16 Pa, which will be conducive to the feeding of branches, but the speed is too high and it will also lead to the enhancement of the vortex of part of the area in the crushing device, which will affect the feeding of branches and the throwing of the crushed material. affect the feeding of branches and the throwing out of crushed materials, and finally determined the speed range of the crushing knife roller is 1800 ~ 2220 r/min. Based on ANSYS/Model module modal analysis of the crushing knife roller, the knife roller of the first six orders of the intrinsic frequency and vibration pattern, crushing knife roller of the lowest order of the modal intrinsic frequency of 137.42 Hz, much larger than the crushing knife roller operating frequency of 37 Hz, the machine will not resonate during operation.

Two polyurethanes (PUs) were similarly synthesized by reacting a cycloaliphatic isocyanate with 1,4 butanediol and two polyols of different nature (polyester, polycarbonate diol) with molecular weights of 1000 Da. The PU made with polycarbonate diol polyol (YCD) was the only showing intrinsic self-healing at 20 °C. For assessing the mechanism of intrinsic self-healing of YCD, a structural characterization by molecular weights determination, infrared and X-ray photoelectronic spectroscopies, differential scanning calorimetry, X-ray diffraction, thermal gravimetric analysis and dynamic mechanical thermal analysis was carried out. It was concluded that the self-healing at 20 °C of YCD was due to non-covalent dynamic exchange interactions among the carbonate groups of the soft segments. Therefore, the chemical nature of the polyol played a key role in developing PUs with intrinsic self-healing at 20 °C.

To address the problems of insufficient semantic fusion between text and questions and the lack of consideration of global semantic information encountered in machine reading comprehension models, we proposed a machine reading comprehension model called BERT_hybrid based on BERT and hybrid attention mechanism. In this model, BERT is utilized to separately map the text and questions into the feature space. Through the integration of Bi-LSTM, attention mechanism, and self-attention mechanism, the proposed model achieves comprehensive semantic fusion between text and questions. The probabilities distribution of answers is computed using Softmax. Experimental results on the public dataset DuReader demonstrate that the proposed model achieves improvements in BLEU-4 and ROUGE-L scores compared to existing models. Furthermore, to validate the effectiveness of the proposed model design, we analyze the factors influencing the model’s performance.

Nanocrystalline silicon oxide (nc-SiOx:H) is a multipurpose material with its varied application in solar cells as a transparent front contact, intermediate reflector, back reflector layer and even tunnel layer for passivating contacts, owing to easy tailoring of its optical properties. In this work, we systematically investigate the influence of gas mixture (SiH4, CO2, PH3 and H2), RF power and process pressure on the optical, structural and passivation properties of thin n-type nc-SiOx:H films prepared in an industrial, high throughput, plasma-enhanced chemical vapor deposition (PECVD) reactor. We provide a detailed description of the n-type nc-SiOx:H material develop-ment using various characterization techniques (SEM, EDX, Raman spectroscopy, and spectro-scopic ellipsometry) with a focus on the relationship between the material properties and the pas-sivation they provide to n-type c-Si wafers characterized by their effective carrier lifetime (τeff). Further, we also outline the parameters to be kept in mind while developing different n-type nc-SiOx:H layers for different solar cell applications. We report a tunable optical gap (1.8 – 2.3 eV) for our n-type nc-SiOx:H films as well as excellent passivation properties with τeff up to 3.5 ms (iVoc ~ 715 mV) before annealing. Oxygen content plays an important role in determining the crystallinity and hence passivation quality of the deposited nanocrystalline silicon oxide films.

Plant leaf area index (LAI) is a key characteristic affecting field canopy microclimate. In addition to traditional professional measuring instruments, smartphone camera sensors have been used to measure plant LAI. However, when smartphone methods were used to measure conifer forest LAI, very different performances were obtained depending on whether the smartphone was held at the zenith angle or at a 57.5° angle. To validate further the potential of smartphone sensors for measuring conifer LAI and to find the limits of this method, this paper reports the results of a comparison of two smartphone methods with an LAI-2000 instrument. It is shown that both methods can be used to reveal the conifer leaf-growing trajectory. However, the method with the phone oriented vertically upwards always produced better consistency in magnitude with LAI-2000. The bias of the LAI between the smartphone method and the LAI-2000 instrument was explained with regard to four aspects that can affect LAI: gap fraction, leaf projection ratio, sensor field of view (FOV), and viewing zenith angle (VZA). It was concluded that large FOV and large VZA cause the 57.5° method to overestimate the gap fraction and hence underestimate conifer LAI, especially when tree height is greater than 2.0 m. For the vertically upward method, the bias caused by the overestimated gap fraction is compensated for by an underestimated leaf projection ratio.

Fungal infections caused by Candida spp. are responsible for high hospital morbidity and mortality rates. Therefore, there is a continuous search for new antifungal medicines, particularly ones with anti-Candida activity. This review analyzed articles published between 2002 and 2023 considering the anti-Candida activity of chemical compounds identified or isolated in plants of the Anacardiaceae family. In addition, the in-silico prediction of the isolated compounds described was performed. The analysis of 35 studies showed that extracts, essential oils, and compounds from the anti-Candida activity were frequently determined in vitro using the minimum inhibitory concentration (MIC). The most commonly tested species were Candida albicans, C. tropicalis, C. parapsilosis, C. glabrata, C. krusei, and C. guilliermondii, respectively. Essential oils were the most used form (37% of the studies). The isolated compounds with antifungal effects include cardanol, estragole, trans-anethole, β-caryophyllene, myrcene, catechin-3-o-rhamnoside, β-sitosterol-3-O-glucoside, 24Z-isomasticadienolic acid, oleanolic acid, and oleanolic aldehyde. The in-silico evaluation of those isolated compounds revealed the compounds' drug-likeness and possible antifungal activity. However, some of them showed high toxicity. In conclusion, compounds from the Anacardiaceae family show promise for developing new therapeutic antifungal drugs, especially in combination with conventional antifungals.

This study was designed for the first time to improve phenolic yield and antioxidant activity of ultrasonic-assisted extraction from Acer truncatum leaves (ATL) using response surface methodology, and phenolic composition in ATL extracted under the optimized condition were characterized by UPLC-QTOF-MS/MS. Solvent and extraction time were selected based on preliminary experiments, and a four-factors-three-levels central composite design was conducted to optimize solvent concentration (X₁), material-to-liquid ratio (X₂), ultrasonic temperature (X₃) and power (X₄) for an optimal total phenol yield (Y₁) and DPPH• antioxidant activity (Y₂). The results showed that the optimal combination was ethanol: water (v:v) 66.21%, material-to-liquid ratio 1:15.31 g/mL, ultrasonic temperature 60 °C, power 267.30 W, and time 30 min with three extractions, giving a maximal total phenol yield of 7593.62 mg gallic acid equivalent /100 g d.w. and a maximal DPPH• antioxidant activity of 74241.61 μmol Trolox equivalent/100 g d.w.. Furthermore, 22 phenolics were first identified in ATL extract obtained under the optimized conditions, indicating that gallates, gallotannins, quercetin, myricetin and chlorogenic acid derivatives were the main phenolic composition in ATL. What’s more, a gallotannins pathway existing in ATL from gallic acid to penta-O-galloyl-glucoside was interpreted. All these results provided practical information aiming at full utilization of phenolics in ATL, together with fundamental knowledge for further research.

This research explores the application of Support Vector Machine (SVM) and Digital Surface Models (DSM) derived from Unmanned Aerial Vehicle (UAV) data for a vertical-horizontal classification of mangrove ecosystems in Tongke-tongke and Samataring Village. The study focuses on integrating high-resolution DSM subtracted from Digital Terrain Models (DTM) to classify mangrove vegetation into sixteen distinct vertical-horizontal classes based on vegetation type and elevation. The analysis revealed that older mangroves, particularly those within the 25-35 meters elevation range, dominate the landscape, accounting for 43.40% of the total classified area. This dominance suggests a mature and ecologically stable mangrove ecosystem, which is crucial for biodiversity conservation and carbon storage. The study demonstrates the effectiveness of SVM and UAV technologies in providing detailed and accurate ecological assessments of mangrove forests. The classification results contribute valuable insights into the structural diversity and health of mangrove ecosystems, facilitating targeted conservation and management strategies. Additionally, the research highlights the utility of advanced remote sensing and machine learning techniques in enhancing the precision of environmental monitoring and the assessment of carbon sequestration capabilities within mangrove ecosystems. The findings underscore the potential of UAV-based remote sensing for ecological studies, offering a replicable method for similar assessments in other regions, thereby supporting global environmental management and climate action initiatives.

Oligopeptide transporters (OPTs) are a group of membrane localized proteins that have a broad range of substrate transport capabilities and contribute to numerous biological processes. However, limited information has been reported on OPTs in higher plants. In this study, a comprehensive analysis of the OPT gene family in Medicago truncatula was performed. A total of 26 OPT genes (MtOPT01-MtOPT26) have been identified in the Medicago truncatula genome. Phylogenetic analyses indicated that MtOPTs consisted of two distinct subgroups, 12 MtOPTs belonged to the peptide transport subgroup (PT-OPT) based on their predicted amino acid sequences containing the two highly conserved motifs (NPG and KIPPR) and 14 MtOPTs belonged to yellow stripe subgroup (YS-OPT). The MtOPTs distributed on each of 8 chromosomes in Medicago truncatula. Sequence analysis verified that MtOPTs significant similar to those in other plants. The copy number of MtOPTs was low and the multiply of MtOPTs was simple relatively. Gene structure analysis showed that most of the MtOPTs have various numbers of introns. The multiple of MtOPTs might play different biological roles which were supported by the fact that MtOPTs have a distinct tissue-specific expression pattern. The data obtained in this study will help to better understand the complexity of the MtOPTs gene family and provide new evidence for the function and evolution of the OPT gene family in higher plants.

A method based on ultra performance liquid chromatography with diode array detector (UPLC-DAD) was developed for quantitative analysis of five active compounds and chemical fingerprint analysis of Rosa rugosa. Ten batches of Rosa rugosa collected from different plantations in the Xinjiang region of China were used to establish the fingerprint. The feasibility and advantages of the used UPLC fingerprint were verified for its similarity evaluation by systematically comparing chromatograms with professional analytical software recommended by State Food and Drug Administration (SFDA) of China. In quantitative analysis, the five compounds showed good regression (R²=0.999 5) within the test ranges and the recovery of the method was in the range of 94.2–103.8%. The similarities of the fingerprints of 10 batches of the samples were more than 0.981. The developed UPLC fingerprint method is simple, reliable and validated for the quality control and identification of Rosa rugosa. Additionally, simultaneous quantification of five major bioactive ingredients in the Rosa rugosa samples was conducted to interpret the consistency of the quality test. The results indicated that the UPLC fingerprint as a characteristic distinguishing method combining similarity evaluation and quantification analysis, can be successfully used to assess the quality and to identify the authenticity of Rosa rugosa.

Plant activators have emerged as promising alternatives to conventional pesticides for crop disease manage-ment due to their unique mode of action. By priming the plant's innate immune system, these compounds can induce systemic acquired resistance against a broad spectrum of pathogens without directly inhibiting their proliferation. Key advantages of plant activators include prolonged defense activity, lower effective dosages, and negligible risk of developing pathogen resistance. Among the various defensive pathways tar-geted, the salicylic acid (SA) signaling cascade has been extensively explored, leading to the successful devel-opment of commercial activators like benzothiadiazole for widespread application in crop protection. While the action sites of many SA-targeting activators have been preliminarily mapped to different steps along the pathway, a comprehensive understanding of their precise mechanisms remains elusive. This review provides a historical perspective on plant activator development and outlines diverse screening strategies employed across multiple levels, from whole-plant bioassays to molecular and transgenic approaches. We expound on the intricate components, biological relevance, and regulatory circuits governing the SA pathway, while criti-cally examining the structural features, bioactivities, and proposed modes of action of classical activators such as benzothiadiazole derivatives, salicylic acid analogs, and other small molecules. Insights from field trials as-sessing their practical applicability are also discussed. Furthermore, we highlight the current status, challenges, and future prospects in the realm of SA-targeting activator development globally, with a focus on recent en-deavors in China. Collectively, this comprehensive review aims to synthesize existing knowledge and provide a roadmap for future research toward developing more potent and mechanistically understood plant activa-tors that fortify crop immunity against disease.

Broad bean paste (BBP) is a traditional fermented soy food, and its high salt content not only prolongs the fermentation time but also threatens human health. In this study, three BBP-meju with different salt concentrations were prepared, and the effects of varying salinity on the fermentation process were comprehensively compared. The results showed that salt-reduced fermentation contributed to the accumulation of amino acid nitrogen, reducing sugars, free amino acids, and organic acids. Alcohols, esters, aldehydes, and acids were the main volatile flavor compounds in BBP-meju, and the highest total volatile flavor compounds were found in medium-salt meju. Bacillus, Staphylococcus, Aspergillus, and Mortierella were the dominant microbial communities during fermentation, and there were also three opportunistic pathogens, Enterobacter, Pantoea, and Brevundimonas, respectively. According to Spearman correlation analysis, Wickerhamomyces, Bacillus, Staphylococcus, and Mortierella all showed highly significant positive correlations with ≥3 key flavor compounds, which may be the core functional flora. Furthermore, the dominant microbial genera worked synergistically to promote the formation of high-quality flavor compounds and inhibit the production of off-flavors during salt-reduced fermentation. This study provides a theoretical reference for the quality and safety control of low-salt fermented soy foods.

The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

The flowering period of rice significantly impacts variety adaptability and yield formation. Properly shortening the reproductive period of rice varieties can expand their ecological range without significant yield reduction. Targeted genome editing, like CRISPR/Cas9, is an ideal tool to fine-tune rice growth stages and boost yield synergistically. In this study, we developed a CRISPR/Cas9-mediated multiplex genome editing vector containing five genes related to three traits: Hd2, Ghd7, and DTH8 (flowering stage genes), along with the recessive rice blast resistance gene Pi21 and the aromatic gene BADH2. This vector was introduced into the high-quality Geng rice variety in Zhejiang province, Jiahe212 (JH212), resulting in 34 T0 plants with various effective mutations. Among the 17 mutant T1 lines, several displayed diverse flowering dates, but most exhibited undesirable agronomic traits. Notably, three homozygous mutant lines (JH-C15, JH-C18, and JH-C31) showed slightly earlier flowering dates without significant differences in yield-related traits compared to JH212. Through special Hyg and Cas marker selection of T2 plants, we identified 7, 6, and 2 fragrant glutinous plants devoid of transgenic components, respectively. These single plants will serve as sib lines of JH212 and potential resources for breeding applications, including maintenance lines for Xian-Geng interspecific three-line hybrid rice. In summary, our research offers practical insights and potential resources for targeted improvement of Geng rice varieties, and would also promote the Geng rice varieties expending from the southward to the northward.

Dielectric elastomers, such as thermoplastic polyurethanes (TPU), are widely used as dielectric layer, emulation layer and substrate of flexible and stretchable devices. To construct capacitors and actuators that work stably upon deformation, it has become an urgent need to investigate the evolution of dielectricity under stress and strain. However, the lack of effective methods for estimating the dielectric constant of elastomers under strain poses a big challenge. This article reports a device for in-situ measuring the dielectric constant of TPU under strain. It is found that upon stretching TPU to a strain of 400%, its dielectric constant decreases from 8.47 to 2.94. In addition, combined Fourier-transform infrared spectroscopy, X-ray scattering technique, and atomic force microscopy have been utilized to characterize the evolution of microstructure under strain. The investigation under tensile strain reveals that a decreased density and average size of polarized hard domains, along with a tendency of the molecular chains to align in parallel with the tensile stress. The evolution of the microstructures results in a reduction of the dielectric constant parallel to the electric field in TPU. Our work provides valuable experimental reference for improving the stability of flexible sensors and actuators based on dielectric elastomers.

The one-dimensional MoS₂/carbon nanofibers (1D MoS₂/CNFs) are synthesized by electrospinning using exfoliated MoS₂ nanosheets and polyacrylonitrile as raw materials. The exfoliated MoS₂ nanosheets with size of about 150 nm are encapsulated in carbon nanofibers, and the free-standing MoS₂/CNFs can be easily cut into flexible tablet and directly used as binder-free anode for lithium storage. The resultant 1D MoS₂/CNFs exhibit a very high reversible capacity of 700 mAh g^-1 at 100 mA g^-1 after 50 cycles, high rate capacity (450 mAh g^-1 at 1000 mA g^-1 after 200 cycles) and good cycle stability.

The Doppler band compensated by the keystone transform (KT) is limited. Therefore, it needs to be used in conjunction with the Doppler ambiguity compensation function to correct the range migration (RM) caused by maneuvering targets with Doppler ambiguity. However, the KT implemented by sinc interpolation suffers from significant performance loss at boundaries of compensation Doppler bands. Additionally, in a multi-target scenario, KT implementation methods occupy high complexity when the Doppler range of targets spans over two compensation Doppler bands. To address aforementioned issues, this study presents a variable Doppler starting point keystone transform (VDSPKT) method, where a new form of ambiguity compensation function is constructed, turning the Doppler starting point of the compensation band in KT variable. Firstly, the position of the compensation Doppler band is changed from fixed to adjustable as needed, enhancing the flexibility of KT. Crucially, the connection points of the compensation Doppler bands in sinc interpolation are reset, avoiding the performance loss at their boundaries. Also, the compensation band is adjusted to cover the narrow Doppler frequency range caused by targets, significantly improving the computational efficiency. Finally, the simulation results demonstrate that the proposed approach effectively addresses the performance degradation and high computational complexity of KT in the aforementioned scenarios, resulting in a computational load reduced by approximately 50% compared to traditional methods.

Both bacteria product flagellin and macrophages are implicated in HIV infection/disease progression. However, the impact of their interaction on HIV infection and the associated mechanisms remain to be determined. We thus examined the effect of the flagellins on HIV infection of primary human macrophages. We observed that the pretreatment of macrophages with the flagellins from the different bacteria significantly inhibited HIV infection. The mechanistic investigation showed that the flagellin treatment of macrophages downregulated the major HIV entry receptors (CD4 and CCR5) and upregulated the CC chemokines (MIP-1α, MIP-1β, and RANTES), the ligands of CCR5. These effects of the flagellin could be compromised by a toll like receptor 5 (TLR5) antagonist. Given the important role of flagellin as a vaccine adjuvant in TLR5 activation-mediated immune regulation and in HIV infection of macrophages, future investigations are necessary to determine the in vivo impact of flagellin-TLR5 interaction on macrophage-mediated innate immunity against HIV infection and the effectiveness of flagellin adjuvant-based vaccines studies.

The intelligent morphing wing structure has the characteristics of flexibility, large deformation and adaptive change, which are different from those of the conventional wing. The motion law of the variable-camber leading edge is analysed by the numerical simulation method based on kinematics theory to solve the problem of verifying the motion function and structural strength of the variable camber wing. The driving deformation and aerodynamic load simulation of the variable camber leading edge are realised by designing a follow-up load test apparatus. Based on the numerical simulation of the mechanical boundary, the motion trajectory of the upper and lower wing loading points was predicted, and a multi-point cooperative control system was developed. Multi-sensor iteration was used to ensure the loading accuracy of the test control. The test results show that the average error of the deflection angle is 4.59% in the variable camber leading edge motion test. In the variable camber leading edge strength test, the average error of applied load magnitude and direction is 0.54% and 0.24%, respectively.

Rhododendron chrysanthum Pall., live in Changbai Mountain being exposed to chilling temperature, high light intensities and water scarcity condition. To adapt to the harsh environment, the cold resistance mechanisms of R. chrysanthum have been successfully evolved in the long-term adaptive process. In our present work, the methods of proteomics combined with physiological and biochemical analyses were used to investigate the effects of cold stress on the photosynthesis and antioxidant system of Rhododendron chrysanthum Pall. and the molecular mechanisms involved in cold resistance of plants. A total of 153 photosynthesis related proteins were identified in present work, of which 7 proteins including Rubisco large subunit (rbcL) were up-regulated in experiment group (EG) compared with control group (CG). Simultaneously, four chlorophyll fluorescence parameters were measured in present study. The results showed that the maximum photochemical efficiency of photosystem II (Fv/Fm), actual quantum yield of PSII (Y(II)) and photochemical quenching (qP) were significantly higher in EG, whereas the non-photochemical quenching (NPQ) was notably decreased. Cold stress could lead to a significant reduction in electron transport rate (ETR) accompanied with an increase in excitation pressure (1-qP). The abundance of PetE which involved in the plants photosynthetic electron transfer was also significantly influenced by cold stress. Moreover, the up-regulated expressions and higher levels of enzymatic activities of Glutathione peroxidase (GPX) and Ascorbate peroxidases (APXs) were detected in EG. All these changes which can help plants to survive in low temperature are considered as the crucial parts of cold tolerance mechanisms. These results revealed that photosynthesis and redox adjustment play significant roles in the defense of cold-induced damage.

Bartonella species, intracellular parasitic zoonotic pathogens, has drawn increasing attention for their diverse host range and associated human diseases. This study investigates Bartonella infection in small mammals in Yunnan Province, China, focusing on tissue tropism. 333 small mammals were sampled from 13 species, 3 orders, 4 families, and 4 genera in Heqing and Gongshan Counties. Conventional PCR and real-time quantitative PCR (qPCR) were utilized for detection and quantification, followed by bioinformatic analysis of obtained DNA sequences. Results show a 31.5% detection rate, varying across species. Notably, Apodemus chevrieri, Eothenomys eleusis, Niviventer fulvescens, Rattus tanezumi, Episoriculus leucops, Anourosorex squamipes, and Ochotona Thibetana exhibited infection rates of 44.4%, 27.7%, 100.0%, 6.3%, 60.0%, 23.5%, and 22.2%, respectively. Genetic analysis identified 30, 10, and 5 strains based on ssrA, rpoB, and gltA genes, with nucleotide identities ranging from 92.1% to 100.0%. Bartonella strains were assigned to B. grahamii, B. rochalimae, B. sendai, B. koshimizu, B. phoceensis, B. taylorii, and a new species identified in the Episoriculus leucops (GS136). Tissue distribution analysis revealed varied copy numbers across different tissues, with the highest load in spleen. These findings underscore Bartonella's diverse species and host range in Yunnan Province, highlighting its broad tissue tropism in small mammals.

Global wastes accumulate at an accelerating rate especially food and slaughterhouse waste constituting a major proportion owing to inefficient management. The high protein concentration of fish waste and keratinaceous byproducts is hazardous, harbouring pathogens, and emitting toxins. Transforming proteinaceous waste into amino acids (AAs) reduces waste bulk and offers a smarter nutrient approach for agriculture. However, this resource remains underutilized triggering eco-system pollution, diseases spreading, and climate change. Currently, small quantities of proteinaceous waste are valorized as animal feed, fertilizer, and in medical, and biotechnological sectors, which cannot solve bulk waste accumulation further, natural AA sources in agriculture are less recognized meanwhile researchers focus on synthetic AAs. Introducing various plant-nutrient formulas enriching fish AA with keratinaceous waste hydrolysate has not been broadly discussed. With this novel approach, using proteinaceous waste resources in agriculture would solve environmental pollution while minimizing land degradation by synthetic fertilizer. In this review, we illustrate the potential and benefits of valorizing proteinaceous waste in bulk through bioconversion. More importantly, we spotlight the biocompatibility of natural AAs and propose an enrichment, to use the ultimate product as catalysts for crops. Consequently, this approach reduces hazardous waste while paving a paradigm change in agriculture.

Water quality assessment in pastoral of Tibetan Plateau, which is water sources for about 40% of world's population and the runoff-yield area of Yellow rivers, is very important. In this paper, Xiahe county which belongs to Tibetan Plateau pastoral was investigated. Six parameters(via, chloride, COD, ammonia nitrogen, nitrate, fluoride, sulfate) were selected to assess the water quality and health degree by using fuzzy comprehensive evaluation methods. The hydrochemical type in surface water was of HCO3--Mg2+-Ca2+ type. The cations and anions in surface water were mainly from weathering and dissolution of carbonate rock. Results showed that the water quality in all 69 sampling sites was all of class Ⅰ. The integrated health degree reached more than 0.85 and the health rate were 100%. Although ammonia nitrogen was regarded as the main contamination factor, but it had a little effect on the entire body of water. Overall, the surface water qualities of most samples in Xiahe County was good condition.

Drowsiness is a main factor for various costly defects, even fatal accidents in areas such as construction, transportation, industry and medicine, due to the lack of monitoring vigilance in the mentioned areas. The implementation of a drowsiness detection system can greatly help to reduce the defects and accident rates by alerting individuals when they enter a drowsy state. This research proposes an Electroencephalography (EEG) based approach for detecting drowsiness. EEG signals are passed through a preprocessing chain composed of artifact removal and segmentation to ensure accurate detection followed by different feature extraction methods to extract the different features related to drowsiness. This work explores the use of various machine learning algorithms such as Support Vector Machine (SVM) the K Nearest Neighbor (KNN) the Naive Bayes (NB) the Decision Tree (DT) and the Multilayer Perceptron (MLP) to analyze EEG signals sourced from the DROZY database, carefully labeled into two distinct states of alertness (awake, and drowsy). Segmentation into 10-second intervals ensures precise detection, while a relevant feature selection layer enhances accuracy and generalizability. The proposed approach achieves high accuracy rates of 99.84% and 96.4% for intra (subject by subject) and inter (cross-subject) modes, respectively. SVM emerges as the most effective model for drowsiness detection in the intra mode, while MLP demonstrates superior accuracy in the inter mode. This research offers a promising avenue for implementing proactive drowsiness detection systems to enhance occupational safety across various industries.

The yak (Poephagus grunniens) has evolved unique adaptations to survive the harsh environment of the Tibetan Plateau, while their gut microorganisms play a crucial role in maintaining the health of the animal. Gut microbes spread through the animal population not only by horizontal transmission but also vertically, which enhances microbial stability and inheritance between generations of the population. Homogenization of gut microbes in different animal species occurs in the same habitat enhancing interspecies coexistence. Using the yak as a model animal, this paper reviews the adaptive strategies under extreme environments and how the gut microbes of the yak circulate throughout the Tibetan Plateau system, which not only affects other plateau animals such as plateau pikas, but can also have a profound impact on the health of people. By examining the relationships between yaks and their gut microbes, this review provides new perspectives in understanding the adaptations of plateau animals and the stability of the ecosystem.

Periodontitis is a chronic inflammatory disease which results in the destruction of the tooth’ s supporting tissues and the alveolar bone resorption. The complement becomes a major link between infection and inflammatory pathology including periodontitis. Gingipians as important virulence factors of P. gingivalis have the activity of C5 convertase, could cleave C5 into fully functional C5a to activate C5aR. The above process could be blocked by the C5aR antagonist (PMX-53) to suppress local periodontal inflammation, and then achieves the purpose of treatment of periodontitis. Nanoparticles incorporated within gelatin are promising carrier system for drug delivery in recent years. This study aimed to investigate whether gelatin nanoparticles loaded with PMX-53 prevents alveolar bone resorption in miniature swines model of periodontitis. Four miniature swines were placed ligatures around the maxillary and mandibular fourth premolar and first molar on both sides for seven weeks to induce periodontitis. Then, animals were assigned randomly to four groups: minocycline-treated group, gelatin with PMX53-treated group, gelatin-treated group and a sham control group. They were treated with 1ml related drugs respectively, into gingival sulcusl for 4 times at one-week intervals. We showed that local treatments with gelatin nanoparticles loaded with PMX-53 could inhibit alveolar bone loss of periodontitis. Our study revealed that gelatin nanoparticles loaded with PMX-53 prevented alveolar bone resorption miniature swines model of periodontitis. In addition, provided proof-of-concept for local targeting of gelatin nanoparticles loaded with PMX-53 as a powerful candidate for the treatment of periodontitis.

The detection, characterization, and monitoring of SARS-CoV-2 recombinant variants is a challenge to public health authorities worldwide. Recombinant variants, composed of two or more SARS-CoV-2 lineages, often have unknown impacts on transmission, immune escape, and virulence in the early stages of emergence. We examined 4,213 SARS-CoV-2 recombinant SARS-CoV-2 genomes collected between 2020 and 2022 from California to describe regional and statewide trends in prevalence. Many of these recombinant genomes, such as those belonging to the XZ lineage, or novel recombinant lineages, likely originated within the state of California. We discuss the challenges and limitations surrounding Pango lineage assignments, the use of publicly available sequence data, and adequate sample sizes for epidemiologic analyses. Although these challenges will continue as SARS-CoV-2 sequencing volumes decrease globally, this study enhances our understanding of SARS-CoV-2 recombinant genomes to date while providing a foundation for future insights into emerging recombinant lineages.

Climate change poses a serious threat to the ancient Magnoliaceae family, particularly for the endangered Yulania trees. Until now, little is known about the suitable geographical range of Yulania zenii, and about how it responds to past and future climate scenarios. Here, we first employed ten models from Biomod2 to preliminarily simulate its potential distribution in China and selected MaxEnt for final modeling. The results showed that among the key environmental factors influencing its distribution, the top three factors were Bio2 (Mean diurnal range), Bio15 (Precipitation seasonality of variation coefficient) and Elevation. Its current suitable distribution were primarily concentrated in southern Anhui, central Hubei, eastern Hunan, southern Jiangsu, northern Jiangxi, and northern Zhejiang. The total suitable area of Yulania zenii was 14.68 × 104 km2, only taking 1.53% of China's total territory, which is larger than known. During the Last Interglacial and Middle Holocene, its suitable habitats were larger than currently, exhibiting a relatively continuous distribution. Under various future climate scenarios, its suitable habitats may averagely decrease by 20.26% compared with the current, and these habitats become more fragmented. Collectively, the centroid of Yulania zenii is expected to migrate towards the southeast in the future. Therefore, our findings demonstrate, for the first time, that climate change takes an adverse effect on this species in distribution from the past to current till future. Our study can contribute to the conservation and management of Yulania zenii in China, and can provide reference for other endangered Yulania species of this country under the condition of climate change.

The predatory mirids Macrolophus pygmaeus Ramber and Nesidiocoris tenuis Reuter (Heteroptera: Miridae) are used for the biological control of Tuta absoluta Meyrick (Lep.: Gelechiidae) and other pests in tomato greenhouses. The functional response of 1 (young) and 10 (old) days old adult females and males of M. pygmaeus and N. tenuis on eggs of T. absoluta, was determined on tomato at two temperatures (20° and 25°C) and LD 16:8 and found to be Type II. M. pygmaeus females exhibited higher predation efficiency, than males at both tested temperatures. Young M. pygmaeus females had a higher efficiency than old ones, whereas males had a low efficiency irrespective of age. The predation efficiency of N. tenuis was high (but lower than M. pygmaeus) in both young females and males, although old females had a higher efficiency than the respective males. Our results show that the two predatory species have different functional response characteristics to their prey depending mainly on sex and age which may affect their role as biological control agents.

Huperzine A is an herbal reversible inhibitor of Acetylcholinesterase (AChE). A molecular docking analysis on Huperzine A molecule has been carried out to understand its structure, conformational flexibility, intermolecular interaction and the binding affinity in the active site of AChE enzyme. Further, the charge density distribution of huperzine A molecule (lifted from the active site of AChE) was determined from the high level quantum chemical calculations coupled with charge density analysis. The binding affinity of Huperzine A towards AChE was calculated from the molecular docking; the lowest docked energy is -8.46 kcal/mol. In the active site, huperzine A molecule interacts with acyl binding pocket-Phe330 of AChE, that is, the bicyclo ring group of huperzine A forms an intermolecular interaction with the oxygen atom of main chain of the amino acid residue Phe330 at the distances 3.02 and 3.25 Å respectively. On the other hand, a gas phase study on huperzine A molecule also performed using HF and DFT (B3LYP) methods with the basis set 6-311G**. The molecular structure, conformation, and the charge density distribution of huperzine A molecule in the gas phase have determined using quantum chemical calculations and the charge density analysis. The comparative studies between the gas phase and the active site forms of huperzine A molecule, explicitly reveals the degree of conformational modification and the charge density redistribution of huperzine A when present in the active site. The dipole moment of the molecule in the active site is 6.85 D, which is slightly higher than its gas phase value (5.91 D). The electrostatic potential (ESP) surface of active site molecule clearly shows the strong electronegative and positive ESP regions of the molecule, which are the expected strong reactive locations of the molecule.

In this paper, a novel microwave catalyst Ni@SiC/CNFs (NSC), C/Ni (NC), and C/SiC (SC) were successfully synthesized by electrostatic spinning method, and proved to degrade methylene blue with high efficiency under microwave irradiation. The results imply that the catalyst Ni@SiC/CNFs with double shell structure gave a 99.99 % removal rate in 90 s for the degradation of methylene blue under microwave irradiation, outperformed the C/Ni and C/SiC and most other reported catalysts in similar studies. On the one hand, the possible mechanism of the methylene blue degradation should be ascribed to that double shell structure increases the polarization source of the material, resulting in excellent microwave absorption properties; and on the other, the in-situ generation of active species OH• and O2 - under microwave radiation and the synergistic coupling effect of metal plasma greatly improved the degradation efficiency of methylene blue. The findings of this study could provide a valuable reference for the green degradation of industrial dye wastewater and its sustainable development process.

More than 20 years after the discovery of the first anelloviruses (AVs), they still remain a mysterious group of viruses. To date, there is no clear understanding of their impact on the host organism, although information is emerging about their participation in various pathologies. However, it is well known that AVs are an important component of the human virome. In the current study we assessed the abundance of AVs in viromes from four nasal and pharyngeal samples from children with respiratory symptoms using a metagenomic approach. It is worth noting that three patients had known respiratory viruses and one did not have any. Regarding AVs, they were detected in all samples, namely Torque teno mini virus (TTMV). The greatest abundance and diversity of AVs (Torque teno virus (TTV), TTMV and Torque teno midi virus (TTMDV)) were shown in a diseased patient with an absence of respiratory viruses, which may indicate the potential involvement of AVs in the maintenance of respiratory symptoms. An activated immune system to combat the main pathogens, against the background of which the number of AVs decreases, is discussed as a possible reason for the reduced diversity of anellome in other patients. We also compared the results of the metagenomic approach and qPCR for major respiratory viruses, which were in agreement. In addition, metagenomic sequencing made it possible to obtain additional data on viral genomes in order to establish their taxonomic identification and characterize individual viral profiles in patients from the Siberian part of Russia.

Abstract: Kiwifruit, a perennial horticultural crop known for its nutritional value, faces significant challenges due to biotic and abiotic stresses, affecting its yield and quality. Leucine-rich repeat receptor-like proteins (LRR-RLPs), a major group of receptor-like proteins in plants, have diverse functions in plant physiology, including growth, development, signal transduction, and stress responses. Despite their importance, the specific roles of kiwifruit LRR-RLPs in response to biotic and abiotic stresses remain poorly understood. In this study, we investigated the expression patterns of kiwifruit LRR-RLPs under various stress conditions, including pathogen stress, heat stress, waterlogging stress, and copper stress. Through genome and transcriptome analyses, we identified a total of 101, 164, and 105 LRR-RLPs in Actinidia Chinensis 'Hongyang', Actinidia eriantha 'Huate', and Actinidia chinensis 'Red5' kiwifruit, respectively, classified into 9 subgroups based on phylogenetic relationships. Synteny analysis revealed that the expansion of kiwifruit LRR-RLPs was primarily attributed to segmental duplication events. Using RNA-seq data from pathogen-infected kiwifruits, we identified specific LRR-RLP genes potentially involved in different stages of pathogen infection. Additionally, we observed the potential involvement of kiwifruit LRR-RLPs in abiotic stress responses, with upstream transcription factors possibly regulating their expression. Furthermore, protein interaction network analysis unveiled the participation of kiwifruit LRR-RLP genes in the regulatory network of abiotic stress responses. These findings highlight the crucial roles of LRR-RLPs in mediating both biotic and abiotic stress responses in kiwifruit, offering valuable insights for the breeding of stress-resistant kiwifruit varieties.

Surface water distribution extracted from remote sensing data has been used in water resource assessment, coastal management, and environmental change studies. Traditional manual methods for extracting water bodies cannot satisfy the requirements for mass processing of remote sensing data; therefore, accurate automated extraction of such water bodies has remained a challenge. The histogram bimodal method (HBM) is a frequently used objective tool for threshold selection in image segmentation. The threshold is determined by seeking twin peaks, and the valley values between them; however, automatically calculating the threshold is difficult because complex surfaces and image noise which lead to not perfect twin peaks (single or multiple peaks). We developed an operational automated water extraction method, the modified histogram bimodal method (MHBM). The MHBM defines the threshold range of water extraction through mass static data; therefore, it does not require the identification of twin histogram peaks. It then seeks the minimum values in the threshold range to achieve automated threshold. We calibrated the MHBM for many lakes in China using Landsat 8 Operational Land Imager (OLI) images, for which the relative error (RE) and squared correlation coefficient (R2) for threshold accuracy were found to be 2.1% and 0.96, respectively. The RE and root-mean-square error (RMSE) for the area accuracy of MHBM were 0.59% and 7.4 km2. The results show that the MHBM could easily be applied to mass time-series remote sensing data to calculate water thresholds within water index images and successfully extract the spatial distribution of large water bodies automatically.

Coronaviruses cause infections in humans and diverse species of animals and birds with a global distribution. Bovine coronavirus (BCoV) produces predominantly two forms of disease in cattle, a respiratory form, and a gastrointestinal form. All age groups of cattle are affected by the respiratory form of coronavirus whereas the gastroenteric form causes neonatal diarrhea or calf scour in young cattle and winter dysentery in adult cattle. The tremendous impacts of bovine respiratory disease and the associated losses are well-documented and underscores the importance of this pathogen. Beyond this, studies have demonstrated significant impacts on milk production associated with outbreaks of winter dysentery, with up to a 30% decrease in milk yield. Research data so far have shown that the viral structure or strain is not a determinant of tissue tropism and clinical form of the disease. In North America, BCoV was identified for the first time in 1972, and it continues to be a significant economic concern for the cattle industry. The virus is classified under Coronaviridae family, Betacoronavirus genus and Betacorovirus 1 species. A number of conventional and molecular diagnostic assays are available for the detection of BCoV from clinical samples. Conventional assays for BCoV detection include virus isolation, which is challenging from clinical samples, electron microscopy, fluorescent antibody assays, and various immunoassays. Molecular tests are mainly based on nucleic acid detection and predominantly include conventional and real-time polymerase chain reaction (PCR) assays. Isothermal amplification assays and genome sequencing have also been used increasingly in recent years for the detection and identification of BCoV. Loop-mediated isothermal amplification, helicase-dependent amplification, recombinase polymerase amplification, and multienzyme isothermal rapid amplification are some examples of the isothermal amplification assays for used BCoV. Point-of-care testing has gained some popularity recently as they can offer user-friendly testing on the farm (barn-side). The present study reviewed literature on coronavirus infections in cattle from the last three and a half decades and presents information mainly on the current and advancing diagnostics in addition to epidemiology, clinical presentations, and the impact of the disease on the cattle industry.

Salt stress is a major limiting factor for alfalfa yield due to its relatively low salt tolerance. High soil salinity adversely impacts alfalfa growth and development, leading to reduced yield. Melatonin (MT) is known to play a significant role in enhancing plant resistance to abiotic stresses. However, the mechanisms underlying melatonin-mediated abiotic stress responses, particularly salt stress, are not well understood. To address this gap, we conducted a study focusing on germinating alfalfa seeds under salt stress. Physiological indexes and transcriptomics analyses were carried out on the germinated seeds to investigate the effects of melatonin on alfalfa seedlings under salt stress conditions. Our results revealed that the application of melatonin led to an increase in shoot length and fresh weight of alfalfa seedlings under salt stress. Moreover, key physiological indexes such as peroxidase (POD) activity and glutathione (GSH) content were enhanced, while levels of malondialdehyde and superoxide anions decreased. Transcriptomic analysis identified a total of 2,131 differentially expressed genes in the salt-treated group, with 726 up-regulated and 1,405 down-regulated genes, while the MT-treated group showed 2896 differentially expressed genes, of which 1,097 were up-regulated and 1,799 were down-regulated. Further, KEGG enrichment analysis highlighted the enrichment of differentially expressed genes in pathways including flavonoid biosynthesis, ABC transporter, glutathione metabolism, and the MAPK signaling pathway, with these pathways more significantly enriched in the MT-treated group. These findings collectively suggest that melatonin plays a crucial role in alfalfa's response to salt stress and offer new insights into the genomic mechanisms underlying melatonin-mediated salt tolerance in alfalfa.