Dogs population increased exponentially in the past decade while the birth rate decreased gradually, especially in the developed countries. Due to dogs’ characteristics of loyalty and obedience, most pet owners treated their dogs as their family members or companions, therefore they are willing to select and purchase safe, high quality and nutrition dog food to their dogs. However, there is lack of regulation or standard to reinforce the production or distribution of dog food in Hong Kong. Consequently, this paper will first review the relationship between high dog population and declining birth rate, types of dog food and typical ingredients. Secondly, the potential health implications of various “toxic” food ingredients for dog, hazard analysis of dog food and its testing methods will be investigated. Lastly, this paper will summarize worldwide existing standards and regulations, quality and hygiene management system related to dog food safety to provide insights and suggestions to Hong Kong government about the importance and urgency of implementing regulations and policies to oversee the imported and local manufactured dog food.

A novel determination method using flow-through cartridge purification and ultra-high-performance liquid chromatography coupled to tandem mass spectrometry (UPLC-MS/MS) was developed for the identification and quantification of 30 mycotoxins (aflatoxin B1, B2, G1, G2, sterigmatocysin, T-2 toxin, diacetoxyscirpenol, roquefortine C, methylergonovine, ergocornine, lysergol, enniatin A, enniatin A1, enniatin B, enniatin B1, beauvericin, deoxynivalenol, 3-acetylDeoxynivalenol, 15-acetylDeoxynivalenol, patulin, verruculogen, neosolaniol, gliotoxin, HT-2 toxin, wortmannin, zearalenone, α-zearalenol, β-zearalenol, α-zearalanol, and β-zearalanol) in feedstuffs. Mycotoxins were extracted from sample by 0.1% formic acid aqueous solution/acetonitrile (16/84 v/v), then purified by a Cleanert® MC clean-up column. As a result, the pigments and other matrices were efficient removed from the sample extract solution. The purified eluate was collected, then evaporated and redissolved by 0.1% formic acid aqueous solution/acetonitrile (70:30 v/v) for UPLC-MS/MS detection. A BEH Shield RP18 chromatographic column was employed for separation of 30 mycotoxins in a total of 14 min. Multiple-reaction monitoring (MRM) mode was applied for qualitative and quantitative analysis, and matrix calibration curves obtained with the external-standard method was used for quantitation of target analytes. Under optimized conditions, the linearity range was from 2 to 1000 ng/g, and the limit of quantification of the developed method was from 2 to 50 ng/g. The recoveries of 30 mycotoxins spiked in urine samples were from 72.0% to 118.5%, and the relative standard deviation was below 20%. The method was also well approved by certified reference sample, and applied on the real feedstuff samples testing successfully.

The conformity assessment of products or a measured value with the given standards is carried out based on the global risk of producers and consumers calculation. A product may conform to specifications but be falsely rejected as non-conforming. This is about the producer's risk. If a product doesn't meet the requirements but is falsely accepted as conforming, that poses a risk to the consumer. The conventional approach to risk assessment, which yields only a single numerical value for the global risk of producers and consumers, is naturally extended, and utilized for assessing risk in measurement models with linear regression. The outcomes of the two-dimensional extension, along a moderate scale, are the parabolas with an opening upwards. Risk surfaces were obtained through three-dimensional extension over the area limited by the moderate scale and guard band axes. Four models with different ranges of tolerance intervals were used to test this innovative method of risk assessment in linear regression. The corresponding standard measurement uncertainties are determined by applying a simplified measurement model with the use of comprehensive data on the measurement performance and by determining measurement uncertainty derived from consideration of the functional relationship obtained by linear regression analysis. Models that utilize information from linear regression analysis to determine measurement uncertainty are biased towards risks at the edges of the moderate scale. Testing the model's performances with metrics related to the confusion matrix, such as the F1 score, further substantiated this assertion. The diagnostic odds ratio has been proven to be extremely effective in identifying the curve along the guard band axis, along which the global risks of producers and consumers are at their lowest.

In order to solve the problem of the poor oil displacement effect of high molecular weight alkali/surfactant/polymer (ASP) solution in low permeability reservoirs, Daqing Oilfield uses a partial quality tool to improve the oil displacement effect in low permeability reservoirs. Without changing the oil displacement capability of high molecular weight ASP solution in high permeability oil layers, the ASP solution is actively sheared in low permeability oil layers by using a partial quality tool to increase the injection capability of the solution and improve the overall oil recovery. In order to study the ability of the partial quality tool to improve the oil displacement effect, firstly, the matching degree of high molecular weight ASP solution to low permeability cores is studied, and the ability of quality control tools to change the molecular weight is studied. Then, experimental research on the pressure and oil displacement effect of high molecular weight ASP solution before and after the actions of the partial quality tool is carried out. The results show that ASP solutions with molecular weights of 1900 × 104 and 2500 × 104 have a poor oil displacement effect in low permeability reservoirs. After the action of the partial quality tool, the injection pressure is reduced by 5.22 MPa, and the oil recovery is increased by 7.79%. The injection pressure of the ASP solution after shearing by the partial quality tool is lower than that of the ASP solution with the same molecular weight and concentration without shearing, but the oil recovery is lower. On the whole, the use of the partial quality tool can obviously improve the oil displacement effect in low permeability reservoirs.

In this study, a basic study was performed to analyze the seasonal temperature status of a research room in the Global Environment Research Building where ceiling-embedded indoor units are installed to study the room temperature status of the building as well as to improve its thermal environment. In addition, a direction for improvement of the indoor thermal environment in the winter was proposed through a CFD (computational fluid dynamics) simulation and was proven by an additional experiment. Through the results of this study, it appeared that if the ceiling-embedded indoor unit was installed in the small indoor space without considering the thermal vulnerability of its perimeter boundary, the air temperature of the upper part was greatly different from that of the bottom part in the winter. Hence, in this study, as a means to improve it, convectors were installed to minimize the effect of the external thermal environment and angle-controllable air flowing fans were installed to mitigate the stratification distribution. With such result, it was intended to present the essential data for improvement of the thermal environment as well as conservation of heating energy in the winter for buildings by reviewing the use of the ceiling-embedded indoor unit in the future.

The adulteration of goat milk powder occurs frequently, cattle-derived and soybean-derived ingredients are common adulterants in goat milk powder. However, simultaneously and rapidly detecting cattle-derived and soybean-derived components is still a challenge. high throughput and efficient screening method for adulteration detection is need. In this study, a rapid method was developed to detect the adulteration of common cattle-derived and soybean-derived components simultaneously in goat milk powder by combining the CRISPR/ Cas12a system with recombinant polymerase amplification (RPA). A dual DNA extraction method was employed, primers and crRNA for dual detection were designed and screened, and a series of condition optimizations were carried out in this experiment. The optimized assay can rapidly detect cattle-derived and soybean-derived components in 40 min. The detection limits of both cattle-derived and soybean-derived components were 1% (w/w) for the mixed adulteration models. The established method was applied into a blind survey of 55 commercially available goat milk powder products. The results showed that 36.36% of the samples contained cattle-derived or soybean-derived ingredients, which revealed the noticeable adulteration situation in the goat milk powder market. This study realizes a fast flow of dual extraction, dual amplification and dual detection of cattle-derived and soybean-derived components in goat milk powder for the first time. It can be used for high-throughput and high-efficiency on-site primary screening of goat milk powder adulterants, and provide a technical reference for combating with food adulteration.

Two new dimacrolide sesquiterpene pyridine alkaloids (DMSPAs), dimacroregelines A (1) and B (2), were isolated from the stems of Tripterygium regelii. The structures of both compounds were characterized by extensive 1D and 2D NMR spectroscopic analyses, as well as HRESIMS data. Compounds 1 and 2 are two rare DMSPAs possessing unique 2-(3′-carboxybutyl)-3-furanoic acid units forming the second macrocyclic ring, representing the first example of DMSPAs bearing an extra furan ring in their second macrocyclic ring system. Compound 2 showed inhibitory effects on the proliferation of human rheumatoid arthritis synovial fibroblast cell (MH7A) at a concentration of 20 μM.

The circular economy is one of the main strategies for mitigating the environmental impacts of civil construction, due to the generation of construction and demolition waste (CDW). In this transition, evaluating alternatives for using buildings as material banks is a way to make the process of reusing construction components more efficient. Thus, the article aimed to evaluate the state of the art of publications on the relationship between the circular economy in civil construction and the conceptual model of buildings as material banks, to mitigate the environmental impacts of CDW. The authors chose the methodological design of Systematic Literature Review, using the Scopus and Web of Science databases for research, with the following search strings: ("construction" or "civil construction" or "built environment" or "construction industry" ) and ("circular economy" or "circular construction") and ("material banks" or "BAMB" or "buildings as material banks" or "building stocks" or "building materials") and ("construction waste" or "demolition waste" or "CDW" or "construction and demolition waste" or "environmental impacts"). After a screening in which only articles published in journals were selected, from 2013 to 2023, inclusion and exclusion criteria were applied, to evaluate only those that had a direct relationship with CDW management through circular economy strategies and buildings such as banks of material. As a result, 93 articles remained, which were analyzed using quantitative and qualitative approach. The quantitative results showed an increase in publications since 2020, which are concentrated in European countries and China. The predominance of applied studies was also noted, through case studies that evaluate the management of materials and waste in the urban environment. The qualitative analysis, carried out using a SWOT Matrix, highlighted the strengths of the buildings, such as material banks, the potential reduction of resource extraction and urban mining, promoting the circulation of construction products. However, the recycling of waste, such as aggregates, still stands out as the main end-of-life strategy adopted, even without occupying the top of the waste hierarchy.

The role of foods is shifting from focusing on the provision of energy and basic nutrients to also include bioactive compounds that prevent the development of chronic age-related diseases. Mi-croalgae offer a source of nutritional compounds with important health effects, and have the po-tential for production of health-promoting products, without increasing agricultural land use and negatively impacting the environment. Here we investigate the health effects of microalgal ex-tracts with high levels of the colourless carotenoid phytoene. Phytoene is widely available from dietary sources and can be detected across different tissues in the human body. However, it is usually regarded as a precursor for the synthesis of other carotenoids, rather than a bioactive molecule. We utilised the model organism C. elegans to show that phytoene-rich extracts from Chlorella sorokiniana and Dunaliella bardawil have anti-ageing properties. The extracts protect against oxidative damage and amyloid-β42 proteotoxicity (a major pathology of Alzheimer's disease), and extends lifespan. We show that pure phytoene also has these anti-ageing effects, suggesting that phytoene is a bioactive molecule with positive effects on ageing and longevity.

Background/Objectives: PEMF therapy has gained significant attention due to its potential benefits in promoting tissue repair and improving overall well-being. Recent publications in the field of exercise physiology, showed that pulsed electromagnetic fields (PEMFs) enhanced the velocity and the quantity of muscle O2 available and the rate of muscle oxygen extraction and utilization, in semi-professional cyclists, during a heavy constant-load exercise. In this paper, we investigate the effect of stimulation on muscular activation, in sedentary young people, during a constant-load exercise, performed at moderate intensity. Methods: Nine male sedentary young people, partic-ipated in this study. The response of the muscle activity, was recorded by surface EMG and assessed measuring the root mean square (RMS) normalized to the peak of the maximum voluntary con-traction. Data were collected in the right vastus Medialis (RVM) and right Biceps Femoris (RBF) at the baseline (standstill sitting), on warm-up (unloaded cycling) and during 30 minutes of con-stant-load exercise, in two experimental conditions (PEMF ON vs PEMF OFF). Results: The mul-tivariate analysis of variance performed on RVM showed a significant effect of PEMF in both warmup and exercise, while on RBF showed a significant effect of PEMF and warmup. Conclusions: PEMF strongly enhanced the amplitude of muscle activity in young sedentary people. The increase in the amplitude of the muscular response may lead to a higher oxygen consumption and release.

Properties of time domain parameters of the vibration signal have been extensively studied for the fault diagnosis of rolling element bearings (REB). Parameters like kurtosis and Envelope Harmonic-to-Noise Ratio are most widely applied in this field and some important progress has been made. However, since only one-sided information is contained in these parameters respectively, problems still exist in practice when the signals collected are of complicated structure and/or contaminated by strong background noises. A new parameter, named Shock pulse index (SPI), is proposed in this paper. It integrates the mutual advantage of both parameters above and can help effectively identify fault related impulse components under the interference of strong background noises, unrelated harmonic components and random impulses. The SPI optimizes the parameters of Maximum Correlated Kurtosis Deconvolution (MCKD), which is used to filter the signals under consideration. Finally, the interested transient information contained in the filtered signal can be highlighted through demodulation with Teager Energy Operator (TEO). Fault related impulse components can therefore be extracted accurately. Simulations and experiment analyses verify the effectiveness and correctness of the SPI.

Bacteriophages (phages) are potential alternatives to chemical antimicrobials against pathogens of public health significance. Understanding the diversity and host specificity of phages is important for developing effective phage biocontrol approaches. Here, we assessed the host range, morphology, and genetic diversity of eight Salmonella enterica phages isolated from a wastewater treatment plant. The host range analysis revealed that six out of eight phages lysed more than 81% of the 43 Salmonella enterica isolates tested. The genomic sequences of all phages were determined. Whole genome sequencing data (WGS) data revealed that phage genome sizes ranged from 41 to 114 kb with GC contents be-tween 39.9 and 50.0 %. Two of the phages SB13 and SB28 represent new species Epsep-timavirus SB13 and genera Macdonaldcampvirus, respectively as designated by the In-ternational Committee for the Taxonomy of Viruses (ICTV) as per genome based taxonomic classification. One phage (SB18) belonged to the Myoviridae morphotype while the re-maining phages belonged to the Siphoviridae morphotype. The gene content analyses showed that none of the phages possessed virulence, toxin, antibiotic resistance, type I-VI toxin-antitoxin modules or lysogeny genes. Three (SB3, SB15 and SB18) out of the eight phages possessed tailspike proteins. Whole genome-based phylogeny of the eight phages with their 113 homologs revealed three clusters A, B, C and seven subclusters (A1, A2, A3, B1, B2, C1 and C2). While cluster C1 phages were predominantly isolated from animal sources, cluster B contained phages from both wastewater and animal sources. The broad host range of these phages highlights their potential use to control the presence of S. enterica in foods.

Obesity is a highly prevalent chronic disease characterized by excessive weight gain and fat accumulation. There is growing evidence that Lactiplantibacillus plantarum strains with bile salt hydrolase (BSH) activity are effective in preventing and alleviating obesity. However, few of them has confirmed the anti-obesity effect of BSH by gene deletion. In this study, 23 BSH-positive Lp. plantarum strains were screened by bile salt precipitation halo assay. Among these strains, Lp. plantarum Lp20 showed the highest BSH activity with a hydrolysis rate to glycodeoxycholic acid (GDCA) by 91.62%. Genomic sequencing and bioinformatics analysis indicated that gene bsh1 was associated with BSH activity of Lp. plantarum Lp20 and gene deletion of bsh1 confirmed the role of Bsh1 in GDCA hydrolysis. To investigate if the Bsh1 from Lp. plantarum Lp20 could alleviate obesity, the wild type and bsh1 deletion mutant strains were administered daily for 8 weeks to diet-induced obese mice, respectively. Compared with mutant strain, the wild type strain Lp20 significantly reduced body weight gain, inguinal white adipose tissue and mesenteric fat mass in obese mice. In addition, Lp20 also reduced serum total cholesterol levels and LDL-C by 20.8% and 33.3%, respectively. Furthermore, the recovered liver steatosis was only observed in Lp. plantarum Lp20 treated mice. Taken together, the bile salt hydrolase Bsh1 from Lp. plantarum Lp20 was a key functional factor on ameliorating HFD-induced obesity by reducing cholesterol levels and suppressing adipogenesis in mice.

We introduce the notion of generalized contraction on dualistic partial metric spaces. A fixed point theorem for mappings satisfying above mentioned contraction is obtained. Some consequences of our result are obtained. We construct an example to demonstrate the effectiveness of our result among the corresponding results in partial metric spaces. Our results provide substantial generalizations and improvements of several well known results existing in the comparable literature. We discuss an application of our fixed point results to show the existence of solution of functional equations.

The aim of the study was to test the significance of the EPT index in the water quality assessment of three types of water bodies in hilly and mountainous region of Serbia. The aquatic macroinvertebrate community was dominated by the group of insects, of which 95 taxa represent the EPT group. We compared the obtained values of biological indices used for the assessment of water quality according to the national legislation with the overall status assessment represented by the ecological quality classes (EQC). The results of the Spearman correlation test showed a negative correlation of EQC with the EPT index, BMWP score, H', total number of taxa and number of sensitive taxa, while a positive correlation was observed for the values of SI and Tubificinae %. The values of EQC and biological indices were subjected to principal component analysis (PCA). The results showed that the parameters that contributed most to the differences were the EPT index, the BMWP score and the number of sensitive taxa. The results indicate that the EPT index is an excellent indicator of changes in water quality and an important tool for the ecological categorization of water bodies in mountain regions.

In this study, it was analyzed that the characteristics of ammonia and their effects on secondary particulate matter (PM) formation by region in Korea during 2020. The NH3 concentration was high in GJ (11.4 ppb) neighboring agricultural area followed by DJ (9.0 ppb) and SE (8.6 ppb) locating in the urban area. On the other hand, BI (2.6 ppb) and JI (4.5 ppb), which are background regions, were lower than other area. Seasonally, ammonia was high in spring and summer, and it generally increased when human activities are active. Therefore, it is believed that ammonia in the atmosphere changes depending on not only local emissions but also temperature-dependent phase distribution characteristics. For SE and GJ, regions with relatively high ammonia concentrations, the effect of ammonia on secondary PM formation was conducted. In both regions, the ammonium-to-sulfate mole ratio tended to increase with an ammonia or PM2.5 concentration increasing. It can be assumed that PM2.5 concentration increases as nitrates are formed under the ammonia sufficient condition. The adjusted gas ratio is generally greater than 4, indicating that there is a lot of free ammonia. Thus, it is estimated that reduction of ammonia would not effective to restrain the nitrate formation.

Silver ion (Ag+) are recognized for their potent antibacterial properties; however, their utilization in food preservation is restricted by factors such as inadequate stability, a transient antibacterial impact, and the potential for human absorption. Hydrogel-based antibacterial agents are capable of exerting their antibacterial effects by establishing appropriate microenvironments, which facilitate the efficient delivery of antimicrobial molecules to the contaminated regions of food. In previous studies, we observed that chitosan (CS) and silver nitrate (AgNO3) were able to reduce Ag+ to silver nanoparticles (AgNPs) with enhanced antibacterial properties. This not only significantly extended the stability of the antibacterial agent but also demonstrated exceptional inhibitory capabilities against pathogenic bacteria, including common grape contaminants such as P. expansum, A. niger, and B. cinerea. Utilizing ultrasound-induced complexation technology, this study has successfully synthesized a chitosan-silver (CS-AgNPs) hydrogel. The efficacy of this hydrogel against the pathogenic fungus responsible for jujube black spot disease has been thoroughly investigated. The morphology structures of CS-AgNPs hydrogels were characterized by TEM, FTIR and UV-vis. The results indicated that AgNPs ranging from 80 to 110 nm were uniformly dispersed within the gel matrix and remained stable for extended periods at room temperature. In vitro antibacterial assays and fractional inhibitory concentration index (FICI) studies revealed that the pronounced antibacterial efficacy of the CS-AgNPs hydrogel was primarily attributed to the additive antibacterial effect of CS and AgNPs. These insights underscore the significant potential of CS-AgNPs hydrogels in combating fungal diseases of jujube, offering innovative strategies and materials for the management of agricultural pathogens.

Many ecosystems are being severely degraded, leading the United Nations to deem 2021-2030 as the Decade on Ecosystem Restoration. To be successful, this effort requires robust monitoring tools to assess land reclamation practices. Our study aimed to evaluate the quality of recovery efforts in mined areas by developing a Recovery Quality Index (RQI) based on soil and vegetation indicators. Using the heavily mined Iron Quadrangle region of Brazil as an example, we selected four local, undisturbed reference areas as restoration goals: Atlantic Forest (AF); ferruginous rupestrian grassland with dense vegetation (FRGD); ferruginous rupestrian grassland with sparse vegetation (FRGS); and quartzite rupestrian grassland (QRG). We also selected four areas that were directly or indirectly affected by mining, including an environmental compensation area set aside 5 years prior to the study (COMP-5), two sterile piles that had undergone recovery for 15 and 20 years (SP-20 and SP-15), and a cave area with 15 years of recovery (CAVE-15). The four recovery areas were grouped together with each individual reference area (making four combinations of sites), and measurements of 2 vegetation parameters and 34 soil attributes were used in a Principal Component Analysis (PCA) for each grouping. We determined the RQI for each group by summing weighted PCA scores for responsive indicators. Vegetative parameters had the lowest RQI weights in all four groups. Soil physical indicators tended to be the most important, except in AF, where chemical indicators were most relevant. RQI values were also lowest when AF was used as the reference, showing that the forest was a unique ecosystem, and the CAVE-15 site had lower RQI scores than the other restored sites, indicating the high degree of disturbance that occurred in that low-lying area. The SP-20 site tended to have higher RQI values than the SP-15, and similar values to the less disturbed COMP-5 areas, potentially indicating greater recovery of native soil properties during the longer recovery period. This RQI-based approach has excellent potential for robust assessment of the recovery of areas degraded by mining and can support decision-making during monitoring.

Pardosa pseudoannulata is one of the most common wandering spiders in agricultural fields and a potentially good bioindicator for heavy metal contamination. However, little is known about the mechanism by which spiders respond to heavy metals at the molecular level. In this study, high-throughput transcriptome sequencing was employed to characterize the de novo transcriptome of the spiders and to identify differentially expressed genes (DEGs) after cadmium exposure. We obtained 60,489 assembled unigenes, 18,773 of which were annotated in the public databases. Ultimately, 3450 cDNA simple sequence repeats were identified and validated as potential molecular markers in the unigenes. A total of 2939, 2491 and 3759 DEGs were detected among the three libraries of two Cd-treated groups and the control. Functional enrichment analysis revealed that metabolism processes and digestive system function were predominately enriched in response to Cd stress. At the cellular and molecular levels, significantly enriched pathways in lysosomes and phagosomes as well as replication, recombination and repair demonstrated that oxidative damage resulted from Cd exposure. Based on the selected DEGs, certain critical genes involved in defence and detoxification were analysed. These results may elucidate the molecular mechanism underlying spiders' responses to heavy metal stress.

Partial Differential Equations (PDEs) constitute a fundamental framework for modeling various physical phenomena across diverse fields such as physics, engineering, and finance. Solving PDEs accurately and efficiently remains a significant challenge, particularly when dealing with complex systems or high-dimensional data. In this paper, we present a novel approach based on deep learning techniques to investigate the effective factors in solving PDEs. Our methodology leverages the expressive power of deep neural networks to learn and represent the underlying relationships between input parameters and the solutions of PDEs. By incorporating domain knowledge into the network architecture and training process, our approach aims to provide insights into the key factors influencing the solution of PDEs. We demonstrate the effectiveness of our method through numerical experiments on various PDEs, showcasing its capability to identify important features and improve predictive accuracy. Our findings suggest that deep learning techniques offer a promising avenue for understanding and analyzing the complex dynamics inherent in PDEs, paving the way for enhanced computational methods in scientific and engineering applications.

In this study, 10%PTFE/PEEK blend were modified by potassium titanate whisker (PTW) and chopped glass fiber (GF), respectively. The blends were prepared by three-screw extruder. Through the investigation of thermal stability, tribological properties, mechanical properties and rheological behavior, the effects of reinforcing agents were determined. The results illustrated that the mechanical properties of 10%PTFE/PEEK blend can be dramatically improved by adding reinforcing agent of PTW or GF, and the reinforcing effect of GF was especially obvious. As for tribological properties, 1% addition was the best proportion. The friction coefficient and wear rate of the blend with 1% PTW were 0.283 and 4.97 × 10^-6 mm³/N · m, which decreased by 7.2% and 21% compared with those of the blend without reinforcing agent.

This review provides a comprehensive and updated information on chalcones, presenting their sources, methods of identification and properties putting emphasis on applications in agricultural industry. Vast exploitation of synthetic pesticides led to the weed and pest resistance issue, causing economic loss but more importantly health risk due to pesticide overuse. Because one of the aim of the European Green Deal 2030 is the Farm to Fork strategy which targets on reducing by 50% the use of chemical pesticides by 2030, and push towards natural pesticides which are more environmentally friendly and restore natural resources, chalcones and their derivatives seem to fit perfectly. They have herbicidal, fungicidal, bactericidal and antiviral properties. Moreover, chalcones are naturally occurring substances, known for their favorable health effect for years, working on many areas. This review is complementary to the previous ones describing chalcones use in agriculture, updates them but additionally shows methods of detection.

The Saudi Vision 2030 is critical to boosting national development, notably in the construction industry. The construction industry is getting a lot of attention in a variety of ways, the most visible of which is the promotion of best practices, including project management office (PMO) applications. Hail province, like others, is experiencing project delivery issues. Thus, the purpose of this research is to explore the suitable PMO model for Hail public construction projects. A literature review included the drive factors for establishing PMO in construction firms, as well as PMO models and typologies that describe functions. Therefore, those drive factors and PMO models were subjected to a focus group to explore their suitability in the context of Hail. The research findings reveal that the Enterprise PMO is the main for Hail public construction pro-jects, followed respectively by the Program Management Office model and the Project Management Center of Excellence (PMCOE). This method of selection a PMO model is driving construction companies and related businesses to change in order to improve the sector while also ad-dressing construction project delivery challenges in Hail province.

Solar photovoltaic (PV) generation suffers from multiple serious issues, for example shading effects directly affect the performance of installed PV arrays. By studying these issues, it can play a key role in improving the limitations and performance of PV panels. The study of PV arrays under partial shading conditions is mentioned in many papers as a part of other studies and as an independent phenomenon. Therefore, it is essential to improve these studies and update them with new research and study this problem in detail to know how to limit the effects of partial shading irradiance conditions on PV arrays performances, including economical aspects. This paper proposes to study the effects of different partial shading irradiance conditions for a PV array in various configurations. The analysis is proved in detail through the simulation of the proposed PV array in the Matlab/Simulink environment. The obtained results show the performances of interconnected PV arrays under different partial shading irradiance and temperature conditions, including the solar array I-V and P-V characteristics. In addition, different PV array configurations with and without bypass and blocking protection diodes improve and minimize the effect of partial shading conditions and avoid the reductions in output power.

Grain quality, cooking quality and nutritional quality traits are some of the major attributes that enhance uptake and utilisation of improved cowpea varieties. Therefore, there is need for a better understanding of the genetic variation and inter-relationships among these quality traits in cowpea to integrate them in cowpea breeding programs. The study was conducted to determine genetic variability among 306 cowpea genotypes for grain quality, cooking quality and nutritional quality traits and to understand the interrelationships among these traits for exploitation in breeding programs. The results showed highly significant differences (P

Keywords: early childhood; education; quality; measurement; monitoring; majority world; Item Response Theory; psychometrics

The partial discharge (PD) event in high voltage insulation releases energy, exerts mechanical pressure, and generates elastic waves. Detecting and locating these PD events through short-duration acoustic pulses is well-established, particularly in gas-insulated systems and oil-insulated transformers. However, its full potential remains untapped in solid insulation systems, where the propagation capability of acoustic pulse and the acoustic reflections pose fundamental challenges to the Acoustic Emission (AE) detection technique. This study investigates the influence of reflections and multiple paths on the propagating acoustic pulse in polymeric insulating materials using a finite element method (FEM) in COMSOL. It was observed that the reflections from the boundary influence the propagating pulse's shape, peak magnitude, and arrival time. An analytical MATLAB model further quantifies the impact of multiple propagation paths on the shape, magnitude, and arrival time of the pulse travelling in a cylinder. Additionally, a Perfect Matched Layer (PML) was implemented in the COMSOL model to eliminate reflections from the boundary, and it revealed that the acoustic pulse magnitude decreases with distance following the inverse square law. In essence, the models aid in measuring how reflections contribute to the observed signals, facilitating the precise identification of the source of the PD event in the tested system.

Attention to the work-related musculoskeletal disorders (WMSDs) involve also statistical surveys showing an increasing trend in the incidence of WMSDs. Technological development retrieves new tools and methods for the assessment of physical load at work. In addition to the conventional questionnaires and scaling assessment systems, these methods are mostly based on the direct sensing of appropriate parameters, which allows more precise quantification. The aim of this paper is to compare the assessment of ergonomic risk through current legislative regulations. A Captiv wireless sensor system was used at a car headlight quality control assembly workplace for sensing, data acquisition and data processing. During the evaluation of the postures and movements at work, we discovered differences in the applicable standards: Decree 542/2007 Coll. (Slovak legislation), STN EN 1005-4+A1, French standards default in the Captiv system. Standards define the thresholds for hazardous postures with significant differences in several evaluated body segments, which also affects the final evaluation of the measurements. Based on the results of our research, we found that respondents were in an acceptable position for approximately 63% of the total duration of the work activity in terms of the Legislative method, 44% with Captiv and 27% with Standards method.

Infrared thermography is a contactless imaging technique, useful to measure surface temperature at distance which has been widely applied in animal production. The possible applications within the pig husbandry include sow heat detection, reduction of the incidence of neonatal mortality, recognition of febrile state caused by pathogens, study of metabolic efficiency, evaluation of stress caused by heat, by constraints, or by aggressive interaction and meat quality prediction. Even if this technique could be easily influenced by environmental factors, the continuous improvement in the procedures and the decrease in the cost of the equipment will allow in the next future new and more applications in swine farming.

The main purpose of our research is the evaluation of the efficacity of solvent polarity on phenolic composition, as well as the antibacterial, and antioxidant activities of extract of Moroccan Mentha aquatica L., leaves. To attempt these objectives, the HPLC-DAD was used to identify the biomolecules. The total amount of phenolic and flavonoid content was determined using the Folin-Ciocalteu and aluminum trichloride processes as well as the DPPH, RP, and TAC tests were used to evaluate the antioxidant capabilities. In addition, by employing both in vitro and in silico analysis through the microdilution method, the minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) of the extracts were assessed against multidrug-resistant bacteria. Furthermore, the High-Performance Liquid Chromatography (HPLC) analysis indicated that all extracts of M. aquatica were abundant in noteworthy phytochemical compounds, especially gallic acid, vanillic acid, chlorobenzoic acid, quercetin, and kaempferol. Furthermore, the results indicated that the total phenolic content was higher in hydroethanolic extract (62.19 ± 1.19 mg GAE/g DW) in contrast to the acetonic and aqueous extracts (22.22 ± 0.64, and 22.44± 0.57 mg GAE/g DW) respectively. Similarly, the aqueous ethanol extract contained the greatest flavonoid concentration, with values of 29.15± 0.09 mg QE/g DW when compared with the other extracts. The seam extract poses excellent antioxidant power with an IC50 of 0.06 ± 0.00 mg/mL for the DPPH test, and lower RP with EC50 of 80± 0.00 µg/ml when compared with acetonic and aqueous extract (370± 0.00 and 460± 0.01 µg/mL) respectively. Moreover, the hydroethanolic extract has a high level of TAC 75.09± 2.00 mg EAA/g DW, followed by aqueous extract carrying a value of 28.53 ± 1.36 mg EAA/g DW. The antibacterial capacity is ranged between 0.78 ± 0.05 mg/mL and 12.60 ± 0.00 mg/L. The results of the in-silico study demonstrated that quercetin, vanillic acid, and naringenin components contribute to the antioxidant capability. While gallic acid, kaempferol, and quercetin components are attributed to the antibacterial capacity.

The optimization of photovoltaic (PV) systems is vital for enhancing efficiency and economic viability, especially under Partial Shading Conditions (PSCs). This study focuses on the development and comparison of traditional and advanced algorithms, including Perturb and Observe (P&O), Incremental Conductance (IC), Fuzzy Logic Control (FLC), Grey Wolf Optimization (GWO), Particle Swarm Optimization (PSO), and Artificial Neural Networks (ANN), for efficient Maximum Power Point Tracking (MPPT). Simulations conducted in MATLAB/SIMULINK evaluated these algorithms’ performance under various shading scenarios. The results indicate that while traditional methods like P&O and IC are effective under uniform conditions, advanced techniques, particularly ANN-based MPPT, exhibit superior efficiency and faster convergence under PSCs. The study concludes that integrating AI and ML into MPPT algorithms significantly enhances the reliability and efficiency of PV systems, paving the way for broader adoption of solar energy technologies in diverse environmental conditions. These findings contribute to advancing renewable energy technology and support the green energy transition.

Ultramafic rocks become promising candidates for carbon sequestration by enhanced carbon dioxide (CO2) mineralization strategies due to their highly CO2-reactive mineral composition and its abundant availability. This study reports a mineralogy and microtextures of a representative ultramafic rock from the Ma-Hin Creek in northern Thailand and observes evidence of CO2 mineralization occurring through the interaction between CO2 and the rock with the existence of water under ambient conditions. After sample collection, rock description was determined by optical petrographic analysis. The rock petrography reveals a cumulated wehrlite comprising over 50% olivine and minor amounts of clinopyroxene, plagioclase, and chromian spinel. Approximately 25% of the wehrlite has altered to serpentine and chlorite. A series of CO2 batch experiments were conducted on six different rock sizes at a temperature of 40°C and pressure of 1 atm over five consecutive days. The post-experimental products were dried, weighed, and geochemically analyzed to detect changes in mineral species. Experimental results showed that product weight and the presence of calcite increased with reducing grain size. Additionally, the modal mineralogy of the wehrlite theoretically suggests a potential CO2 uptake of up to 53%, which is higher than the average uptake values of mafic rocks. These findings support the suitable rock investigation approach and the preliminary assessment of carbon mineralization potential, contributing to enhanced rock weathering techniques for CO2 removal that could be adopted by mining and rock supplier industries.

Face milling is a well known commercial process highly used in heavy industries that consumes high amount of power. Besides power issue, modern manufacturing industries are aiming for per part cost reduction keeping the product quality unimpaired. Unexpectedly if the part is rejected in any stage of manufacturing, the cost of manufacturing dramatically increases. Major cause of part rejection is excessive tool wear that imparts poor surface profile or catastrophic tool failure that causes adherence of broken tool debris onto machined surface. Furthermore, the tool wear is associated with sliding distance (frictional distance) and the tool life quantifies the cost of tools. As such, from the perspective of manufacturing industries it is imperative to optimize the surface quality parameter, cost of part, power consumption, and material removal – this is exactly what is accomplished here. By this work, it is possible to conserve power consumption, produce parts with lower cost, manufacture with uncompromising surface quality and enhanced material removal rate. Moreover, as intermediate factors of interest, the influences of sliding distance, tool life and tool flank wear on the overall machining performance are evaluated. The multi-objective optimization by Grey Relational Analysis (GRA) revealed that for improved product performance and fast manufacturing (case 1) optimum results are: feed per tooth fz = 0.25 mm/tooth, cutting speed vc = 392.6 m/min and cutting length l = 0.5 mm; for resource conservation (case 2) the optimum results are: feed per tooth fz = 0.125 mm/tooth, cutting speed vc = 392.6 m/min, cutting length l = 0.5 mm.

Background. The European Centre for Disease Prevention and Control describes the community pharmacist as gatekeeper to the quality of antibiotic use. The pharmacist has the responsibility to guard safe and effective antibiotic use; however, little is known about how this is implemented in practice. Aims. To assess the feasibility of a method to audit the quality of antibiotic dispensing in community pharmacy practice and to explore antibiotic dispensing practices in Greece, Lithuania, Poland, and Spain. Methods. The Audit Project Odense methodology to audit antibiotic dispensing practice was adapted for use in community pharmacy practice. Community pharmacists registered antibiotic dispensing on a specifically developed registration chart and were asked to provide feedback on the registration method. Results. Altogether twenty pharmacists were recruited in four countries. They registered a total of 409 dispenses of oral antibiotics. Generally, pharmacists were positive about the feasibility of implementing the registration chart in practice. The frequency of checking for allergies, contraindications and interactions differed largely between the four countries. Pharmacists provided little advice to patients. The pharmacists rarely contacted prescribers. Conclusion. This tool seems to make it possible to get a useful picture of antibiotic dispensing patterns in community pharmacies. Dispensing practice does not seem to correspond with EU guidelines according to these preliminary results.

The growing interest in benchtop NMR systems is visible in a vast number of applications in science and industry. Low-field nuclear magnetic resonance (LF-NMR) became an instant in technologies that productions are dependent on the reliable structure identification, grade and purity control, chemical process inspection or reaction monitoring. Beyond the benefits of being cost-, space-, maintenance- and user friendly, insufficient sensitivity and low signal resolution are the main drawbacks, due to which the low-field NMR (LF-NMR) in the fields of organic chemistry and synthesis remains limited to solely academic teaching purposes. Herein, we discuss the possibilities of LF-NMR for the needs of organic chemistry and synthesis on a set of compounds 1-4 achieved as the products of student’s laboratory course and organic derivatives 5-8 that are from our research interests. Chemical structure determination of all compounds 1-8 presented herein was performed using the benchtop-type NMR instrument operating at 60 MHz (Pulsar Oxford Ltd.). Structure of novel compounds 5-7 prepared under the aims of our research was characterized by combined 1H/19LF-NMR and compared with an appropriate high-field NMR data from Bruker Ascend Instrument (400 MHz). Finally, possibilities of the low-field NMR as an analytical tool for the research purposes in the fields of organic chemistry and synthesis are documented on a set of 1H and 2D 1H-1H COSY for azomethine 8.

The construction industry has a notable negative impact on the environment; thus, the promotion of the use of timber structures is an alternative to mitigate its effects. The research develops an artificial intelligence-based decision approach in the calculation of timber structures focused on the enhancement of the sustainability of roof structures. Based on the optimization carried out through genetic algorithms and the framework established in Eurocode 5, a general set of equations has been proposed for a laminated timber roof structure. The tool, which determines the most suitable roof structure for each strength class of laminated timber, allows for the determination of the dimensions of beams and purlins and their respective separations in order to minimize wood consumption. The ultimate goal is to offer multiple solutions regarding strength classes and structural designs in order to foster informed sustainable choices that promote efficient use of resources in construction.

Objectives: Evaluate the performance of diagnostic measures (sensitivity and specificity) of the intrinsic capacity (IC) construct recommended by the WHO ICOPE guidelines by domain and by age group. Study design: This cross-sectional study included 164 community-dwelling elderly (95 women and 69 men). The participants completed the assessment of the 5 domains of IC (cognition, psychological, vitality, locomotion and sensory). In addition, they were assessed for activities of daily living (ADL), instrumental activities of daily living (IADL), frailty and urinary incontinence. Main outcomes measures: Descriptive statistics were used to summarize the intrinsic capacity and identify which domains were compromised. Comparisons between three or more samples were made by 1-way ANOVA with Bonferroni post-test and those with two samples by the t-test or Mann-Whitney test for quantitative variables. Chi-square test was used for qualitative variables. The sensitivity and specificity of each domain and each domain by age group were evaluated using the ROC curve. Results: Participants with a decline in IC were older, worse ADL, IADL and mental function, low gait speed, and higher depression scores. In addition, people with a decline in IC had frailty, urinary incontinence. Other issues related to the decline in CI were self-reported non-practice of physical activities and level of schooling.The evaluation of each domain did not prove to be a good screening tool (sensitivity or specificity < 80%, but both values > 50%). When the analyses were separated by domain and age group, good performance was found in the psychological (69-69 years and ≥80 years), vitality (≥80 years) and sensory (≥80 years) domains. Conclusions: The ICOPE screening tool performed well in terms of diagnostic measures when applied by domain and age group.

A Partial discharge (PD) occurrence in high-voltage (HV) and medium-voltage (MV) power assets is a warning sign of insulation system degradation or defective manufacturing/assembly, that may cause catastrophic damage and eventually lead to the breakdown of the power equipment. Ultra-high frequency (UHF) PD measurement technology has extensively been used to monitor the insulation health of the HV or MV equipment due to its high immunity against ambient noise and conducted disturbances. This paper presents experimental validation of a new design of a UHF planar rectangular microstrip antenna that can be used for PD monitoring of HV and/or MV power equipment, such as power transformers. The designed planar rectangular microstrip antenna has a compact size of 80mmx70mmx1.6mm. Laboratory experiments were performed to validate the antenna sensitivity to PD activity caused by insulation defects created inside an oil-filled transformer tank model. PD measurement results confirm that the proposed rectangular microstrip antenna has high sensitivity and high signal-to-noise ratio (SNR), thanks to its capability to suppress external noise disturbances, especially during online PD monitoring. Thus, the proposed UHF antenna seems to be a promising and alternative PD sensor that can be employed in UHF PD monitoring systems of HV or MV power equipment.

Background: Intrauterine transfusion (IUT) of the donor and partial exchange (pET) of the recipient is a temporizing treatment for pregnancies with Twin Anemia Polycythemia Sequence (TAPS). We sought to give a detailed description of the procedural approach and outcomes for sequential donor IUT and recipient pET in TAPS. Methods: Retrospective study of spontaneous TAPS referred to the Johns Hopkins Center for Fetal Therapy treated with donor IUT followed by recipient pET utilizing a double-syringe set up. Procedure characteristics and outcomes as well as accuracy of existing transfusion formulas were analyzed and compared with the literature. Results: 5 of 78 patients with spontaneous TAPS underwent a total of 19 combined IUT/pET procedures (median first procedure to delivery interval 5.6 weeks [interquartile range IQR 1.9-6.0]). One pET was stopped for fetal decelerations. Patients delivered at 33.0 weeks [IQR 31.9-33.3] with two survivors and no neonatal transfusion requirements. IUT volumes were 48 ml [IQR 39-63 ml] and pET volumes 32 ml [IQR 20-50] utilizing aliquots of 5 – 20 mls for the latter (p=0.021). For IUTs, assumption of a fetal blood volume below 150 ml/kg underestimated required transfusion volume. For pETs, all formulas required adjustment of dilution volume based on bedside testing (p<0.05 for all). Conclusions: Donor transfusion followed by partial exchange in the recipient can prolong pregnancy in spontaneous TAPS and obviate the need for neonatal transfusion. A double-syringe setup facilitates efficient saline exchange. Because the accuracy of volume formulas is limited, bedside testing is recommended to achieve the target hemoglobin.

A superior variant of dried jujube in China is ‘Huizao’ (HZ) jujube. Nonetheless, detailed evaluations of the texture quality of HZ fruits have been the subject of few studies. Texture is a significant indicator of the sensory and processed quality of a fruit. Here, we differentiate and characterize the texture quality of HZ fruits from the four primary producing regions in southern Xinjiang, as well as develop a system for assessing the texture quality of HZ fruits. Furthermore, five texture indices of HZ fruits from 109 plantations were exhaustively evaluated utilizing principal component analysis, Pearson correlation analysis, and hierarchical clustering analysis. Consequently, by the 10th, 30th, 70th, and 90th percentiles, each index was classified into five grades—lower, medium, high, and higher. Correlation investigation indicated strong relationships between the springiness, chewiness, cohesiveness, gumminess, and hardness of HZ fruits. Springiness, hardness, and adhesiveness are essential indicators that influence the texture of HZ fruits. We used clustering analysis to separate the six texture indices into three major categories (hard factor, stick-elastic factor, and adhesive factor), with indices representing hardness, springiness, and adhesiveness, respectively. Furthermore, according to the factor molecules, the texture quality of HZ fruits in the four production areas was evaluated as Bazhou (1.24) > Hotan (0.773) > Kashi (-0.577) > Aksu (-0.852). RDA analysis of six texture quality parameters and 24 climate conditions identified higher mean temperature (TEM) and lower relative humidity (RHU) as the primary factors contributing to the improved texture quality of HZ fruits in Xinjiang. This study identified the texture quality characteristics of HZ fruits in four major producing areas of Southern Xinjiang, and it offered a theoretical foundation for optimizing the dominant producing areas and regional production of HZ varieties in Xinjiang.

In multi-objective optimization problems, the optimization target is to obtain a set of non-dominated solutions. Comparing solution sets is crucial in evaluating the performances of different optimization algorithms. The use of performance indicators is common in comparing those sets and, subsequently, optimization algorithms. A good solution set must be close to the Pareto-optimal front, well-distributed, maximally extended and fully filled. Therefore, an effective performance indicator must encompass these features as a whole and must be Pareto dominance compliant. Unfortunately, some of the known indicators often fail to properly reflect the quality of a solution set or cost a lot to compute. This paper demonstrates that the Degree of Approximation (DOA) quality indicator, is a weakly Pareto compliant unary indicator that gives a good estimation of the match between the approximated front and the Pareto-optimal front. Moreover, DOA computation is easy and fast.

Group A rotaviruses (RVA) have been identified as the leading cause of neonatal calf diarrhea (NCD) In Yunnan, China, despite the limited documentation on this issue within the country. Given the significant impact on animal health and welfare, further attention is warranted to comprehend the prevalence and epidemiology of this disease. In this study, we isolated RVA strains from NCD clinical samples to support RVA epidemic study and further disease control in Yunnan. Material and Methods: Ten fecal samples were obtained from calves with a single episode of neonate calf diarrhea from a farmer during a severe NCD outbreak. For the diagnosis of Group A rotavirus (RVA) infection, fecal reverse transcription-polymerase chain reaction (RT-PCR) was employed as the primary method. Subsequently, RVA isolation was conducted on MA104 cells, with inoculates being pretreated with trypsin TPCK to enhance viral infectivity. The isolated RVA strain was further confirmed through RT-PCR and immunofluorescence assay. Results: RVA virus was isolated from clinical samples following six passages depended on trypsin treatment of inoculates. The sign of CPE detected consisted of increased cell granularity, obscure cell boundaries, cell rounding, and eventual degeneration and detachment of cells. Analysis of sequencing revealed that field isolates was of group A serotype. Phylogenetic analysis based on the ORF sequences of the VP4 and VP7 sequences segments indicated that the isolate was classified as the P[1] genotype. VP4 gene of strain YN-1 shares 75.2%-99.7% nucleotide identity of and 81.6%–99.7% amino acid identity with the complete VP4 sequences of the P[1]. The complete VP7 gene of YN-1 is 981 nucleotide long and encode 326 amino acids. The RotaC v2.0 analysis classified the sequence as the G8 genotype. The VP7 gene of strain YN-1 shares 88.5%-97.7% nucleotide identity and 94.2%-99.1% amino acid identity. Conclusion: This is the first study in China which reports the circulation of Group A NCD on cattle farms in the field. Our study constitutes a crucial and a necessary step allowing preventive and veterinary medicine to support RVA disease controls in Yunnan province, China.

Analysis of non-stationary and nonlinear sound signals obtained from dynamical processes is one of the greatest challenges in signal processing. Turning machine operation is a highly dynamic process persuaded by many events such as dynamical responses, chip formations and operational conditions of machining. Traditional and widely used fast Fourier transformation and spectrogram is not suitable for processing sound signals acquired from dynamical systems as its result have significant deficiencies because of stationary assumptions and having priori basis. The relatively new technique, Discrete Wavelet Transform, which uses Wavelet decomposition and the recently developed technique, Hilbert Huang Transform (HHT) which uses Empirical Mode Decomposition have notably better properties in the analysis of nonlinear and non-stationary sound signals. This paper presents a comparative study on the decomposition of multicomponent sound signals using Empirical Mode Decomposition and Wavelet Decomposition to highlight the suitability found in HHT to analyze tool-emitted sound signals received from turning processes. Apart from the short mathematical and theoretical foundations of the transformations, this paper demonstrates their decomposition strength using an experimental case study of tool flank wear monitoring in turning. It also concludes HHT is more suitable than DWT to analyze tool-emitted sound signals received from turning processes.

Sarcopenia is associated with clinical complications, which increase mortality. Effective sarcopenia risk screening in the elderly should be grounded in a comprehensive assessment, encompassing both nutritional status and medication use. Current screening tools, while emphasizing muscular per-formance, exhibit limited sensitivity in identifying elderly individuals at risk of sarcopenia. This cross-sectional study aimed to develop a sarcopenia risk screening tool, named Sarc-Global, with enhanced sensitivity, incorporating factors pertinent to the overall health of the elderly. Utilizing the criteria established by EWGSOP2 for diagnosing sarcopenia, we evaluated 395 communi-ty-dwelling elderly individuals. This evaluation served as a reference for assessing the efficacy of two validated questionnaires, Sarc-F and Sarc-CalF, and our newly developed Sarc-Global. Con-structed through multiple logistic regression, Sarc-Global integrates variables such as sex, age, medication use, body mass index, arm circumference, and handgrip strength – all significantly associated with sarcopenia (p

Alternative fertilizations are essential to minimize the deteriorating effects of chemical fertilizers on soil and water quality/health. Accordingly, the present work investigated the effects of combined organic-inorganic fertilization (COIF) on wheat and rice yields, soil nutrients, and soil Cd accumulation. Hence, seven different treatments were set up: control (CK); conventional fertilization (CF); optimized fertilization (OF); organic fertilizer replacing 25% (T1) and 50% (T2) of OF; and organic nitrogen (N) replacing 25% (M1) and 50% (M2) of OF-N. Overall, significant increases occurred in the yields of COIF crops. Compared with the CF, the highest wheat and rice yields happened in M1 treatment (approximately by18.5%) (P < 0.05). COIF slightly alleviated soil acidification, and improved the cation exchange capacity (CEC) of the study soils. Besides, COIF treatments significantly increased the contents of total phosphorus, total potassium, available phosphorus, and available potassium by 6.35 to 16.9 %, 3.17 to 10.9 %, 5.53 to 28.7 %, and 2.6 to 12 %, respectively (P <0.05). Nevertheless, negligible increases took place in Cd content of COIF soils compared with the CK. Altogether, our results concluded on 25% replacement of OF-N by organic N (M1) to effectively improve the fertility/ecological sustainability of the study soils.

Geopolymers, made from aluminosilicate raw materials, offer significant environmental advantages over conventional concrete (CC) mixes. This study explores the compressive strength, setting time, and durability of geopolymer concrete (GPC) cylinders, some of which include an additional ordinary portland cement (OPC) mix. Consistent material composition and testing methods are emphasized to achieve reliable results. MATLAB was utilized to develop and assess a neural network model predicting the compressive strength of GPC based on key variables. The model was validated using 16 experimental samples and 1047 samples from various studies. The performance plot displayed the Mean Squared Error (MSE) over iterations, identifying the best training performance at epoch 658 with an MSE of 5.3408. The Error Histogram highlighted distribution errors between predicted and actual compressive strength values, with the highest range from -1.015 to 0.3587, meaning that the predicted values were mostly within a small margin of error from the actual values. This narrow error range indicates that the ANN model has high accuracy in its predictions, as most errors are small and clustered around zero, demonstrating reliable performance in estimating compressive strength. Regression analysis showed varying correlation coefficients (training set R=0.98373, test set R=0.88164, and whole set R=0.96982), indicating adequate predictive accuracy. The results demonstrate that properly trained neural networks can effectively predict the compressive strength of GPC, highlighting its potential as a sustainable construction material.

Summary Genome assembly projects have grown exponentially due to breakthroughs in sequencing technologies and assembly algorithms. Evaluating the quality of genome assemblies is critical to ensure the reliability of downstream analysis and interpretation. To fulfil this task, we have developed the AssemblyQC pipeline that performs file-format validation, contaminant checking, contiguity measurement, gene- and repeat-space completeness quantification, telomere inspection, taxonomic assignment, synteny alignment, scaffold examination through Hi-C contact-map visualisation, and assessments of completeness, consensus quality and phasing through K-mer analysis. It produces a comprehensive HTML report with method descriptions, tables, and visualisations. Availability and Implementation The pipeline uses NextFlow for workflow orchestration and adheres to the best-practice established by the nf-core community. This pipeline offers a reproducible, scalable, and portable method to assess the quality of genome assemblies – the code is available online.GitHub: https://github.com/Plant-Food-Research-Open/assemblyqc Supplementary information Pipeline usage documentation, parameter descriptions and example outputs are available on GitHub: https://github.com/Plant-Food-Research-Open/assemblyqc/tree/main/docs. A preview report is also hosted online: https://plant-food-research-open.github.io/assemblyqc

The digital transformation in Industry 4.0 has revolutionized quality control paradigms, integrating advanced technologies such as augmented reality, deep learning, and computer vision systems into a new era called "Quality 4.0". This study systematically reviews how these technologies are shaping new practices in continuous quality supervision and improvement, adapting to increasingly automated and connected production environments. Through a comprehensive analysis of the literature, practical applications in various industrial sectors, from manufacturing and agriculture to the production of sweets and snacks, are highlighted. Additionally, the conceptual and detailed design of a quality control system using artificial intelligence tools is presented, focusing on the inspection of dimensions, color, weight, and labeling of MDF boxes. The proposed system demonstrates an effective integration of sensors, high-definition cameras, and deep learning algorithms, validated through tests with boxes of different sizes. The results suggest that the adoption of these technologies not only improves the accuracy and efficiency of inspections but is also essential to maintaining high-quality standards in a dynamic and competitive industrial environment.

Abstract: Peptide pools composed of short amino acid sequences have proven to be versatile tools in various research areas and clinical applications. They are powerful tools for epitope mapping, immunotherapy, and vaccine development. Their importance lies in their ability to map complex protein structures, enabling a comprehensive understanding of immune responses and facilitating the identification of potential therapeutic agents. The application of peptide pools also extends to the field of personalized medicine, offering tailored solutions for diseases such as cancer and infectious diseases. Peptide pools are complex mixtures of immunostimulatory antigens primarily intended for T-cell stimulation. They are commercially available in many different compositions and variants. However, unlike other reagents that consist of only one or a few compounds, peptide pools are highly complex products with limited stability. This makes their quality control a major challenge. Quantitative peptide analysis usually requires sophisticated methods, in most cases isotope-labeled standards and reference materials. None of these are routinely available for these products. Synthesis and purification of all labeled peptides might be required. Usually, this approach would be prohibitively laborious and expensive. Therefore, an approach is needed to provide a practical and feasible method for quality control of peptide pools. With insufficient quality control, the use of such products could lead to incorrect experimental results, which would worsen the well-known reproducibility crisis in the biomedical sciences. Here we propose the use of ultra-high performance liquid chromatography (UHPLC) with two detectors, a standard UV detector (at 214 nm) for quantitative analysis and a high-resolution mass spectrometer (HRMS) for identity confirmation. To be cost-efficient and fast, quantification and identification are performed in one chromatographic run. An optimized protocol is shown, and different peak integration methods are compared and discussed. This work was performed using a peptide pool known as CEF, which consists of 32 peptides derived from cytomegalovirus (CMV), Epstein-Barr virus (EBV) and influenza virus, ranging from 8 to 12 amino acids in length.

Digital photogrammetry has attracted widespread attention in the field of geotechnical and geological survey due to its low-cost, ease of use and contactless mode. In this work, with the purpose of studying the progressive block surficial detachments of a landslide we developed a monitoring system based on fixed multi-view time-lapse cameras. Thanks to a new-developed photogrammetric algorithm based on the comparison of photo sequences through a structural similarity metric and the computation of the disparity map of two convergent views we can quickly detect the occurrence of collapse events, determine their location and calculate the collapse volume. With the field data obtained at the Perarolo landslide site (Belluno Province, Italy), we have preliminary tested the effectiveness of the algorithm and its accuracy in the volume calculation. The method of quickly and automatically obtaining collapse information proposed in this paper can extend the potentials of landslide monitoring system based on videos or photo sequence and it will be of great significance for further research on the link between the frequency of collapse events and the driving factors.

Solid waste management is a major environmental challenge, especially in developing countries, with increasing amounts of waste glass (WG) and waste plastics (WP) not being recycled. In Ethiopia, managing WG and WP requires innovative recycling techniques. This study examines concrete properties with WG and WP as partial replacements for fine aggregate. Tests were conducted on cement setting time, workability, compressive strength, splitting tensile strength, and flexural strength. Concrete grade C-25, with a compressive strength of 25 MPa, was prepared using an optimum ratio of 14% WG and 6% WP. Mechanical properties were tested at 7 and 28 days of curing. At 20% replacement, workability decreased at water-cement ratios of 0.5 and 0.6 but remained stable at 0.4. Thus, a 0.4 ratio was used. For 10% replacement, compressive strength increased by 12.55% and 6.44% on the 7th and 28th days, respectively. At 20% replacement, compressive strength decreased by 14.35% and 0.73% on the 7th and 28th days, respectively. On the 28th day, splitting tensile strength at optimum replacement was 4.3 MPa, an 8.5% reduction from the control mix. However, flexural strength increased by 19.7%, from 12.46 MPa to 15.52 MPa. Overall, WG and WP improved flexural strength but slightly reduced splitting tensile strength.

Magnetogenetics emerges as a transformative approach for modulating cellular signaling pathways through the strategic application of magnetic fields and nanoparticles. This technique leverages the unique properties of magnetic nanoparticles (MNPs) to induce mechanical or thermal stimuli within cells, facilitating the activation of mechano- and thermosensitive proteins without the need for traditional ligand-receptor interactions. Unlike traditional modalities that often require invasive interventions and lack precision in targeting specific cellular functions, magnetogenetics offers a non-invasive alternative with the capacity for deep tissue penetration and the potential for targeting a broad spectrum of cellular processes. This review underscores magnetogenetics' broad applicability, from steering stem cell differentiation to manipulating neuronal activity and immune responses, highlighting its potential in regenerative medicine, neuroscience, and cancer therapy. Furthermore, the review explores the challenges and future directions of magnetogenetics, including the development of genetically programmed magnetic nanoparticles and the integration of magnetic field-sensitive cells for in vivo applications. Magnetogenetics stands at the forefront of cellular manipulation technologies, offering novel insights into cellular signaling and opening new avenues for therapeutic interventions.

The scratch test consists in pushing a tool across the surface of a material at a given penetration depth or applied load. It has several applications in Science and Engineering including strength testing, damage and quality control of thin films and coatings. Despite numerous attempts in scientific literature, the application of scratch test to characterizations of fracture properties remains a heavily controversial topic. Therefore, this investigation arises as an experimental study in order to assess the fracture toughness using scratch test. A study on the effect of cryogenic treatment, performed after tempering, on fracture toughness, via scratch test experiments, of different tool steels has been made. A laboratory investigation on AISI D2, AISI M2 and X105CrCoMo18 steel confirms the possibility of increasing the fracture toughness by carrying out the cryogenic treatment after the usual heat treatment

This study used Dutch potatoes at the end of dormancy as the material to explore the impact of menthol (0.2 and 0.5 g/kg based on potato mass) treatment on sprouting inhibition and potato quality. The findings revealed that a menthol concentration of 0.5 g/kg effectively inhibited potato tuber sprouting and significantly reduced glucoside alkaloids production. After a storage period of 15 days, the sprouting percentage and glucoside alkaloids content of potatoes treated with 0.5 g/kg menthol were observed to be significantly lower at 4.17% and 68.63 mg/kg, respectively, compared to the control group which exhibited values of 100% and 282.01 mg/kg, respectively (P < 0.05). Throughout the storage period, 0.5 g/kg of menthol promoted respiration, reduced malondialdehyde production in potatoes, inhibited polyphenol oxidase activity, and slowed down tissue browning. Additionally, it mitigated the decline in starch and soluble protein content, inhibiting the accumulation of reducing sugars.

Berberis vulgaris L. (Berberidaceae) is a shrub that has been widely used in European folk medicine as an anti-inflammatory and antimicrobial agent. The purpose of our study was to elucidate the mechanisms of antiproliferative action of the plant’s methanolic root extract (BVR) against colon cancer cells. Cytotoxicity and pro-apoptotic activity were determined in human colon adenocarcinoma cell lines (LS180 and HT-29) and control colon epithelial CCD841 CoN cells. According to the MTT assay, after 48 h of cell exposure, the IC50 values were as follows: 4.3; 46.1 and 50.2 µg/mL for LS180, HT-29, and CCD841 CoN cells, respectively, showing the greater sensitivity of cancer cells to BVR. The Cell Death Detection ELISAPLUS kit demonstrated that BVR induced programmed cell death only against HT-29 cells. RT-qPCR with relative quantification method showed significant changes in the expression of genes related to apoptosis in both colon cancer cell lines. The genes BCL2L1 (126.84-366.66%), BCL2L2 (277.08-330.12%), CASP3 (180.36-261.36%) and CASP9 (158.08-213.46%) had significantly elevated expression, while BCL2 (23.08-52.06%) had reduced expression. Furthermore, in a panel of antioxidant tests, BVR showed positive effects (63.93±0.01, 122.92±0.01, and 220.29±0.02 mg Trolox equivalents (TE)/g in the DPPH•, ABTS•+ and ORAC assays, respectively). In the lipoxygenase (LOX) inhibition test, BVR revealed 62,60±0.87% of enzyme inhibition. The chemical composition of BVR was determined using UHPLC-UV-CAD-MS/MS analysis and confirmed the presence of several known alkaloids, including berberine, as well as other alkaloids and two derivatives of hydroxycinnamic acid (ferulic and sinapic acid hexosides). This is the first such extensive assessment of the biological activity of BVR. The results are very promising and encourage for the use of BVR as a comprehensive chemopreventive agent (anti-inflammatory, antioxidant, and pro-apoptotic) in colorectal cancer.

The breeding of stress-tolerant cultivated plants that would allow for a reduction in harvest losses and undesirable decrease in quality attributes requires a new quality of knowledge on molecular markers associated with relevant agronomic traits, on quantitative metabolic responses of plants on stress challenges, and on the mechanisms controlling the biosynthesis of these molecules. By combining metabolomics with genomics, transcriptomics and proteomics datasets a more comprehensive knowledge of the composition of crop plants used for food or animal feed is possible. In order to optimize crop trait developments, to enhance crop yields and quality, as well as to guarantee nutritional and health factors, that provides the possibility to create functional food or feedstuffs, the knowledge about the plants’ metabolome is crucial. Next to classical metabolomics studies, this review focusses on several metabolomics based working techniques, such as sensomics, lipidomics, hormonomics and phytometabolomics, which were used to characterize metabolome alterations during abiotic and biotic stress, to find resistant food crops with a preferred quality or at least to produce functional food crops are highlighted.

Consumer perception of beef is heavily influenced by overall meat quality, a critical factor in the cattle industry. Genomics has the potential to improve important beef quality traits and identify genetic markers and causal variants associated with these traits by genomic selection (GS), and genome-wide association studies (GWAS) approaches. Transcriptomics, proteomics, and metabolomics provide insights into underlying genetic mechanisms by identifying differentially expressed genes, proteins, and metabolic pathways linked to quality traits, complementing GWAS data. Leveraging these functional genomics techniques can optimize beef cattle breeding for enhanced quality traits to meet high-quality beef demand. This paper provides a comprehensive overview of the current state applications of the omics technologies in uncovering functional variants underlying beef quality complexities. By highlighting the latest findings from GWAS, GS, transcriptomics, proteomics, and metabolomics studies, this work seeks to serve as a valuable resource fostering a deeper understanding of the complex relationships between genetics, gene expression, protein dynamics, and metabolic pathways in shaping beef quality.

As the most serious of the many worse new pathological changes caused by diabetes, there are many risk factors for the occurrence and development of DR. It mainly includes hyperglycemia, hypertension, hyperlipidemia and so on. Among them, hyperglycemia is the most critical cause, which plays a key role in the pathological changes of DR.High-sucrose diets(HSDs) lead to elevated blood glucose levels in vivo, which, through oxidative stress, inflammation, the production of AGEs and VEGF, causes plenty of pathological damages to the retina and ultimately bring about loss of vision. The existing therapies for DR primarily target the terminal stage of the disease, when irreversible visual impairment has appeared. Therefore, early prevention is particularly critical. Early prevention of DR-related vision loss requires adjustments to dietary habits, mainly by reducing sugar intake. This article primarily discusses the risk factors, pathophysiological processes, and molecular mechanisms associated with the development of DR caused by HSDs. It aims to raise awareness of the crucial role of diet in the occurrence and progression of DR, promote timely changes in dietary habits, prevent vision loss, and improve the quality of life. The aim is to make people aware of the importance of diet in the occurrence and progression of DR. According to the dietary modification strategies we give, patients can change their poor eating habits timely, avoid the retinopathy that can be avoided theoretically, and obtain a excellent outcome.

Silicon carbide particle-reinforced aluminum matrix (SiCp/Al) composites are significant lightweight metal matrix composites extensively utilized in precision instruments and aerospace sectors. Nevertheless, the inclusion of rigid SiC particles exacerbates tool wear in mechanical machining, resulting in a decline in the quality of surface finish. This work undertakes a comprehensive investigation into the problem of tool wear in SiCp/Al composite materials throughout the machining process. Initially, a comprehensive investigation was conducted to analyze the effects of cutting velocity vc, feed per tooth fz, milling depth ap, and milling width ae on tool wear during high-speed milling under SCCO2-MQL (Supercritical Carbon Dioxide Minimum Quantity Lubrication) ultrasonic vibration conditions. Furthermore, a prediction model for tool wear was developed by employing the orthogonal test method and multiple linear regression. The model's relevance and accuracy were confirmed using F-tests and t-tests. Ultimately, through the utilization of a genetic algorithm, the milling parameters were optimized, resulting in the identification of the most optimal combination of parameters. Empirical findings suggest that the careful selection of milling parameters can significantly mitigate tool wear, extend the lifespan of the tool, and enhance the quality of the surface. This work serves as a significant point of reference for the processing of SiCp/Al composite materials.

In this work, we propose an in-house simulation tool designed for the analysis and optimization of bifacial photovoltaic (PV) modules, which are currently under the spotlight in the renewable energy scenario. The tool is conceived to support researchers and engineers by providing fast and accurate predictions of the PV module yield under various operating and environmental conditions. For a chosen geographical site, the impact of module orientation, tilt, albedo, sky conditions, ambient temperature, and so on, can be effortlessly determined. In case of nonuniformity across the cells dictated by localized architectural shading, dirt, bird drops, defects, a circuit-based cell-level approach can be activated to compute the module production. An extensive simulation campaign is performed by assuming that the panels are installed in Naples without loss of generality. Results are shown to give detailed insights into the performance of bifacial modules, thus providing unambiguous guidelines for their correct installation. Further analyses are conducted to demonstrate the tool capability to quantify the detrimental influence of a poorly-irradiated cell on the backside, as well as of cracked cells.

This study presents an innovative approach for the utilization of industrial by-products and municipal waste in the production of sustainable and environmentally friendly cement mortar. We explored stabilized stainless-steel reduced slag (SSRS) and polyethylene (PE) plastic waste as partial replacements for aggregates. Various engineering properties of the resulting cement mortar specimens, including slump, slump flow, compressive strength, flexural strength, tensile strength, water absorption, and ultrasonic pulse velocity (UPV), were investigated through comprehensive experimental tests. The influence of different water-cement (w/c) ratios and substitution amounts on the engineering properties of the cement mortar samples was thoroughly examined. The findings revealed that an increase in PE substitution adversely affected the overall workability of the cement mortar mixtures, whereas an increase in SSRS amount contributed to enhanced workability. As for the hardened properties, a consistent trend was observed for both cases, with higher w/c ratios and substitution amounts leading to reduced mechanical properties. Water absorption and UPV test results validated the increased formation of porosity with higher w/c ratios and substitution amounts. This study proposes a promising method to effectively repurpose industrial by-products and municipal wastes, transforming them into sustainable construction and building materials. Additionally, a comparative analysis of transportation costs and carbon footprint emissions between SSRS-cement mortar and PE-cement mortar was conducted to assess their environmental impact and sustainability. Generally, higher w/c ratios and replacement levels corresponded to reduced carbon footprint. The geographical location of the source of SSRS and PE remains a challenge and studies to overcome this challenge must be further explored.

Superior fiber quality is one of the most important objectives in cotton breeding. To detect the genetic basis underlying fiber quality, an F2 population containing 413 plants was constructed by crossing Jifeng 914 and Jifeng 173, both of which have superior fiber quality, with Jifeng 173 being better. Five fiber quality traits were investigated in the F2, F2:3, F2:4, and F2:5 populations. Quantitative trait loci (QTL) mapping was conducted based on a high-density genetic map containing 11,488 single nucleotide polymorphisms (SNPs) and spanning 4,202.12 cM in length. Transgressive segregation patterns and complex correlations in the five tested traits were observed. A total of 108 QTLs were found, including 27 for fiber length (FL), 16 for fiber strength (FS), 24 for micronaire (MC), 17 for fiber uniformity (FU), and 24 for fiber elongation rate (FE). Chromosome A7 contained 12 QTL, ranking the first. No QTL was found on chromosome D1 and D11. Each QTL contributed 1.98%–21.45% to the phenotypic variation (PV), including 13 major effect QTLs that contributed more than 10% toward PV. Two QTLs could be repeatedly detected in three populations, including qFL-D3-2 in F2, F2:4, and F2:5 with 9.18%–21.45% of PV, qFS-A11-1 in F2:3, F2:4 and F2:5 with 6.05%–10.41% of PV. Another seven stable QTLs could be detected in two populations, including four major effect QTLs: qFL-A12-3, qFS-D10-2, qMC-D6-2, and qMC-D8-1. Fourteen QTL-overlapping regions were found, which might explain the complex correlations among the five phenotypic traits. Four regions on chromosome A11, D3, D6, and D10 covered by both stable and major effect QTLs are promising for further fine mapping. The genomic regions of the two QTLs detected in three populations and the four major effect QTLs contain 810 genes. Gene functional analysis revealed that the annotated genes are mainly involved in protein binding and metabolic pathways. Fifteen candidate genes in the qFL-D3-2 region are highly expressed in fiber or ovules during fiber initiation, elongation, secondary cell wall thickening, or maturation stages. qRT-PCR revealed that Ghir_D03G005440.1 and Ghir_D03G011310.1 may play a role in promoting fiber initiation, Ghir_D03G006470.1 may be beneficial for promoting fiber elongation. This study provides more information for revealing the molecular genetic basis underlying cotton fiber quality.

The bulk LiNa5Mo9O30 (LNM) crystals were successfully grown in the [010] and [001] directions without internal inclusions and cracks by the Czochralskii method with low temperature gradient. The crystal grown in the [010] direction showed a tendency to twinning. The crystal grown in the [001] direction demonstrated high structural perfection (FWHM=13'') for the (001) plane and high optical quality Δn≈210-5. The laser induced damage threshold was measured along a, b and c axes and was 15.7, 27.0 and 27.5 J/cm2 respectively. The thermo-optical coefficient dn/dT was measured for the main crystallographic axes, which was -5.7510-6, -2.0210-5 and 3.6510-6 K-1 along the a, b and c axes, respectively. The second harmonic generation (SHG) is conducted in crystalline LNM sample. The maximum efficiency value of 3.5% at pump power of 12 W had been achieved.

The aim of this study was to research the quality parameters of honeys directly from Iraqi Kurdistan beekeepers and to compare with European Union law and Central European honeys. In total 30 honey samples directly from Kurdish, Czech and Slovak beekeepers were collected from the year of production 2018. The analyzed physicochemical parameters and bioactive compounds (moisture content, electrical conductivity, diastase activity, hydroxymethylfurfural content, pH, free acidity, total phenolic content, color, color intensity) varied depending on the botanical and geographical origin of honeys. Comparing Kurdistan honeys with a directive relating to honey, only two honey samples had diastase activity lower than limit and one sample had free acidity value at the legislative limit. Based on the results, it was found that the properties of Kurdistan honeys were very similar to the properties of Czech and Slovak honeys, as indicated by the detected statistically non-significant differences (p > 0.05) between the moisture content, electrical conductivity, diastase activity and color. On the contrary, the most significant differences (p < 0.01) were detected in hydroxymethylfurfural content, total phenolic content, and color intensity. Our results indicated the specific properties and the uniqueness of honeys from Iraqi Kurdistan and pointed to the possibility of trading this honey in Europe.

Background: Atopic dermatitis is a chronic condition that significantly affects the daily life of those who suffer from it, requiring complex and personalized management with active participation of the patient in the management of their disease. Objective: to describe the design and development process of a mobile application, using the Design Thinking method, for the follow-up of patients with atopic dermatitis. Methods: User-centered design and prototype creation method, differentiating the phases of the empathize, define, idea, prototype, and test. A purposive snowball sampling was used to recruit patients with atopic dermatitis, family members, and health professionals. Three two-hour workshops were held, attended by 25 people. Results: the parameters to be monitored will include objective data (physical, behavioral, treatments, environmental, integration of daily routines) and subjective data (user experience). On the other hand, it will figure out behavior patterns, set up rewards, foster a feeling of community, and use notifications and a chatbot. Conclusion: The active integration of all stakeholders at each stage of the design and development of the digital solution has improved its relevance and acceptance, resulting in a tool that is expected to significantly improve the management of atopic dermatitis.

This paper is the second part of a two-part report studying the responses of a typical point-contact elastohydrodynamic lubrication (EHL) problem to multiscale roughness that is mimicked by artificially generated waviness with different amplitudes, frequencies, and directions. The previous Part I paper (doi:10.3390/lubricants10120368) focuses on the full film regime, while the current paper focuses on the partial film regime. The amplitudes and frequencies are related to the feature geometry of smooth EHL problems. Generated waviness is input to a transient thermal EHL model. The simulation is conducted 1,600 times for different waviness parameters, loads, and speeds. Eight performance parameters are extracted: the asperity contact ratio, minimum film thickness, maximum pressure, central point film thickness, central point pressure, mean film thickness, coefficient of friction (COF), and the maximum temperature rise. The ratios of the first seven parameters with and without waviness and the asperity contact ratio values are plotted on the frequency–amplitude coordinate plane as contour maps. The influences of the amplitude, frequency, wave direction, load, and speed on the eight performance parameters are analyzed and summarized. The simulated data and plotted contour maps are provided to the readers in the Supplementary Material.

In pediatric burn care, achieving swift healing with minimal complications remains paramount. This investigation assesses polyhexamethylene biguanide (PHMB)'s role in managing superficial partial-thickness burns in children, focusing on the effects of various patient-specific factors on recovery. Through a retrospective analysis of 27 pediatric cases treated with PHMB, we explored the impact of age, burn size, dressing frequency, treatment delay, cold therapy application, and analgesic usage on the duration until reepithelialization. Notably, the majority of patients benefited from early cold therapy, yet only 1 in 3 patients received analgesics. The study reveals a mean healing time of 8.78 days, with the extent of the burn showing a strong correlation to recovery speed. Most treatments were managed outpatient, evidenced by a negligible average hospital stay. Impressively, the intervention recorded no complications. Our findings endorse PHMB as a promising treatment for second-degree burns in young patients, offering healing efficiency on par with or surpassing traditional methods, without increasing complication risks. This investigation underscores the necessity for continued exploration into the optimal application of prehospital interventions and the comprehensive benefits of PHMB in pediatric burn management, advocating for future research aimed at assessing long-term outcomes, including scar quality and patient satisfaction.

A PLS-based quality prediction method is proposed for batch processes using two-dimensional extended windows. To realize the adoption of information in the direction of sampling time and batch, a new definition region of support (ROS), k-i-back-extended region of support (KIBROS), is proposed to establish the extended window, which including the data of the previous sampling times in the same batch, the data of the same sampling time in the historical batches, the data of the previous sampling times in the historical batches and the data of the later sampling times in the historical batches. According to these regions of support, extended windows are established, and different models are proposed based on the extended windows for batch processes quality prediction. Further, using a typical batch process as an example, the injection molding process, the proposed quality prediction method is experimentally verified, proving that the proposed methods have higher prediction accuracy than the traditional method and the prediction stability is also improved.

Adults’ with Intellectual Disabilities (ID) experiences on occupational participation were explored through the prism of Occupational Justice model (MOJ) aiming to shape and develop an occupation-centered model of Quality of Life (QoL). In this qualitative study participated thirteen adults with ID (N=13). A semi-structured interview based on MOJ was constructed and administered to explore perspectives on QoL, as well as injustices regarding occupational participation. The interviews were processed with QSR NVivo8 following content analysis research methodology. An Occupational – Quality of Life (O-QoL) model with an everyday occupations core component has been formed. This model includes three core O-QoL domains: (i) social well-being, (ii) emotional – physical well-being and (iii) material adequacy. Main indicators of O-QoL were the recreational occupations and social activities, while socio-environmental factors such as occupational deprivation have been identified as aggravating. In addition, specific occupations such as leisure activities, physical exercise / sports, art, video games and vocational training could also be beneficial for O-QoL. Moreover, the importance of promoting and supporting the rights of people with ID for employment, independent living and sexual expression was highlighted. The O-QoL could be a valuable conceptual framework in the field of ID, however further research for developing specialized assessment tools and Occupational Therapy interventions to promote O-QoL is needed.

Health-Related Quality of Life (HRQoL) encompasses the comprehensive evaluation of an indi-vidual's health and well-being across multiple dimensions. Mindfulness, recognized as a scientifi-cally supported strategy for anxiety management, plays a role in enhancing both physical and mental health. The Gut-Brain Axis (GBA) serves as the bidirectional communication link between the gastrointestinal system and the central nervous system. This study aims to explore the associa-tion between Mindfulness and factors influencing the GBA in both healthy individuals and those with Inflammatory Bowel Diseases (IBD). A cross-sectional investigation involved 338 adults, in-cluding 50 IBD patients, utilizing validated Greek scales for Mindfulness (MAAS-15), Mediterra-nean Diet (14-MEDAS), and HRQoL (EQ-5D-5L). The questionnaire gathered demographic, an-thropometric, and lifestyle data. Among healthy participants, EQ-5D-5L showed a moderate cor-relation with the MAAS-15 scale (r=0.389, p

In this study, an alternative method to conventional production methods involving thin section copper permanent mould casting (rapid solidification), hot rolling and heat treatment processes to manufacture AISI DC 53 cold work tool steel, has been investigated. In this new method, solidification of the AISI DC 53 was done in the thin section copper mould instead of traditional ingot casting. After solidification, thin slabs obtained was homogenized to 1150 ^oC and hold at this temperature for one hour and then hot rolling was be applied. During hot rolling process, about % 30 reduction in thickness of slab was obtained. After hot rolling, heat treatment (austenitizing, quenching and tempering) have been applied to thin slab. The samples have been taken as cast, as rolled and as heat treated (austenitized and tempered) and the microstructural analysis, hardness tests, retained austenite quantity measurement by XRD method have been performed. The heat treatment and tests have been performed for a commercially available AISI DC 53 which is manufactured by thick section ingot casting and rolling. Hardness values of the AISI DC 53 steels produced by traditional route is in the range of 52-54 HRC after austenitization at 1025 ^oC for one hour and quenched in compressed air and tempered twice at 525 ^oC for 120 mins. On contrary the permanent mould cast AISI DC 53 after homogenization at 1150 ^oC and immediately hot rolling then air cooling and austenitized at 1025 ^oC for one hour then quenched by compressed air and tempered twice at 525 ^oC for 120 mins have hardness valeus in the range of 55-57 HRC. Experiments have revealed that the properties of new rapid solidified steel in permanent copper mould are better than the commercially available steel and have a more refined microstructure than commercially produces alternative. Therefore, the new proposed method can be used as an alternative manufacturing method for cold-work tool steels.

The partial information decomposition (PID) framework is concerned with decomposing the information that a set of random variables has with respect to a target variable into three types of components: redundant, synergistic, and unique. Classical information theory alone does not provide a unique way to decompose information in this manner and additional assumptions have to be made. Inspired by Kolchinsky's recent proposal for measures of intersection information, we introduce three new measures based on well-known partial orders between communication channels and study some of their properties.

Epithelial-mesenchymal transition (EMT) is a cellular biological process involved in migration of primary cancer cells to secondary sites facilitating metastasis. Besides, EMT also confers properties such as stemness, drug resistance and immune evasion which can aid a successful colonization at the distant site. EMT is not a binary process; recent evidence suggests that cells in partial EMT or hybrid E/M phenotype(s) can have enhanced stemness and drug resistance as compared to those undergoing a complete EMT. Moreover, partial EMT enables collective migration of cells as clusters of circulating tumor cells or emboli, further endorsing that cells in hybrid E/M phenotypes may be the ‘fittest’ for metastasis. Here, we review mechanisms and implications of hybrid E/M phenotypes, including their reported association with hypoxia. Hypoxia-driven activation of HIF-1α can drive EMT. In addition, cyclic hypoxia, as compared to acute or chronic hypoxia, shows the highest levels of active HIF-1α and can augment cancer aggressiveness to a greater extent, including enriching for a partial EMT phenotype. We also discuss how metastasis is influenced by hypoxia, partial EMT and collective cell migration, and call for a better understanding of interconnections among these mechanisms. We discuss the known regulators of hypoxia, hybrid EMT and collective cell migration and highlight the gaps which needs to be filled for connecting these three axes which will increase our understanding of dynamics of metastasis and help control it more effectively.

In the former mining district of La Carolina (southern Spain), waste materials were accumulated without first waterproofing the substrate. Additionally, these mining dams were abandoned without any type of restoration, conditions that present a significant risk of contaminating the surrounding soils and waters. Prior to carry out the necessary works for isolating these residues, morphological characterization of the contact with the base substrate is needed. For that purpose, in recent years, different indirect study techniques have been used, among which electrical to-mography stands out. In this work, a less common geophysical technique, magnetometry, both in its magnetic and gra-diometric modalities, is used as an alternative method to analyse the geometry and structure of a mining dam. The results obtained with this methodology are compared with the results provided by electrical techniques, as well as with direct data from mechanical surveys and aerial photo-graphs prior to waste deposition. The magnetic anomaly curves obtained with geometric models generated with the Mag2dc program were also analysed. This comparative study shows the use-fulness of magnetic prospecting in characterizing the base geometry of these mining structures and therefore the interest in its application to environmental characterization studies.

Artificial intelligence (AI)-based conversational models, such as ChatGPT, Microsoft Bing, and Google Bard, emerged as valuable sources of health information for the lay individuals. However, the accuracy of information provided by these AI models remains a significant concern. This pilot study aimed to test a new tool referred to as “CLEAR”, designed to assess the quality of health information delivered by AI-based models. Tool development involved a literature review on health information quality, followed by initial establishment of the CLEAR tool comprising five items that aimed to assess the following: completeness of content in response to the prompt, lack of false information, evidence support, appropriateness, and relevance of the generated content. Each item was scored on a 5-point Likert scale from excellent to poor. Content validity was checked by expert review of the initial items. Pilot testing involved 32 healthcare professionals using the CLEAR tool to assess content on eight different health topics deliberately designed with varying qualities. The internal consistency was checked using the Cronbach α. Feedback through the pilot test resulted in language modifications to improve the clarity of the items. The final CLEAR tool was used to assess health information quality generated through four different AI-based models in five different, yet common health topics. The AI models were ChatGPT 3.5, ChatGPT 4, Bing, and Bard, and the content generated was scored by two independent raters with Cohen κ to assess the inter-rater agreement. The final five CLEAR items were: (1) Is the content sufficient? (2) Is the content accurate? (3) Is the content evidence-based? (4) Is the content clear, concise, and easy to understand? and (5) Is the content free from irrelevant information? Pilot testing using the eight different health topics revealed an acceptable internal consistency with a Cronbach α range of 0.669–0.981. The use of the final CLEAR tool yielded the following average scores: Bing (mean=24.4±0.42), ChatGPT-4 (mean=23.6±0.96), Bard (mean=21.2±1.79), and ChatGPT-3.5 (mean=20.6±5.20). The inter-rater agreement revealed the following Cohen κ values: for ChatGPT-3.5 (κ=0.875, P<.001), ChatGPT-4 (κ=0.780, P<.001), Bing (κ=0.348, P=.037), and Bard (κ=.749, P<.001). The CLEAR tool is a brief yet helpful tool that can aid to standardize testing of the quality of health information generated by the AI-based conversational models. Future studies are recommended to validate the utility of the CLEAR tool to assess the quality of the AI-generated health-related content using a larger sample across various complex health topics.

Reduction of the density operator for quantum subsystems is derived without the use of the Born Rule.

Partial sums of analytic univalent functions and partial sums of starlike have been investigated extensively by several researchers. In this paper, we investigate a partial sums of convex harmonic functions that are univalent and sense preserving in the open unit disk.

Tea (Camellia sinenesis) is a health beneficial beverage and is also a source for extracting bioactive components such as theanine, tea polyphenols (TPP) and tea polysaccharides (TPS). TPS is a group of hetero-polysaccharides bounded with proteins. There were tests showing that TPS had various bioactivities, such as antioxidant, antitumors, antihyperglycemia, anti-inflammation and improving immunity. However, inconsistent results concerning chemical composition and bioactivity of TPS were published in recent years. The advances in chemical composition and bioactivities of TPS were reviewed in the present paper. The inconsistent and controversial results regarding composition and bioactivities of TPS were also discussed.

Neurology is a quickly evolving specialty that requires clinicians to make precise and prompt diagnoses and clinical decisions based on the latest evidence-based medicine practices. In all Neurology subspecialties, Stroke and Epilepsy in particular, clinical decisions affecting patient outcomes depend on neurologists accurately assessing patient disability. Artificial intelligence (AI) can predict the expected neurological impairment from an AIS (Acute Ischemic Stroke), the possibility of ICH (IntraCranial Hemorrhage) expansion, and the clinical outcomes of comatose patients. This review article informs readers of artificial intelligence principles and methods. The article introduces the basic terminology of artificial intelligence before reviewing current and developing AI applications in neurology practice. AI holds promise as a tool to ease a neurologist’s daily workflow and supply unique diagnostic insights by analyzing data simultaneously from several sources, including neurological history and examination, blood and CSF laboratory testing, CNS electrophysiologic evaluations, and CNS imaging studies. AI-based methods are poised to complement the other tools neurologists use to make prompt and precise decisions that lead to favorable patient outcomes.

Displacement mapping is a computer graphics technique that enables the design of components with regularly or randomly textured surfaces that can be quickly materialized on a three-dimensional (3D) printer when needed. This approach is in principle more flexible, faster and more economical compared to conventional texturing methods, but the accuracy of the texture depends heavily on the parameters used. The purpose of this study is to demonstrate how to produce a surface-textured part using polygonal (mesh) modeling software and a photopolymerizable resin, and to develop a universal methodology to predict the dimensional accuracy of the model file log combined with a resin 3D printer. The printed components were characterized on a scanning confocal microscope. In the setup used in this study, the mesh size had to be reduced to 10% of the smallest feature size and the textured layer had to be heavily (x4) overexposed to achieve the desired accuracy. As a practical application, two functional stamps with a regular (honeycomb) and a random texture, respectively, were successfully manufactured. The insights gained will be of great benefit in quickly and cost-effectively producing components with innovative patterns and textures for a variety of hobby, industrial and biomedical applications.

In this paper we present a city-scale (possibly global) air pollution network made of low-cost sensors for particulate matter concentration in the air. The components of presented system are based on our research and experience from previous studies focused on air quality instruments and sensors for addressing urban air pollution. Sensor nodes are produced locally and distributed over a city of Sarajevo, Bosnia and Herzegovina. The system collects, calibrates and displays particulate metal concentrations in real-time. In comparison to the available measurements from governmental institutions, our system demonstrated good agreement of measured parameters, with several advantages including: higher resolution in space and time, lower costs, both horizontal and vertical measurements and many more. One of the capabilities of the system is the real-time air pollution city map with animations. By installing multiple sensor nodes over a slope (cable car), we receive vertical measurements of temperature, humidity and particulate matter concentration in real time, which gives a valuable insight into the dynamics of temperature inversion episodes and air pollution below the inversion layer.

Groundwater is becoming increasingly important in the Pacific Northwest of the USA due to declining snowpack volumes and shifts in precipitation type and timing, all connected with climate change. The Upper Williamson Basin of the Klamath Watershed is a groundwater dominated watershed with massive fluctuations in year-to-year streamflow volumes over the past four decades, including the complete absence of any live flow for several years. The precise relationship between groundwater and streamflow in the basin has been difficult to assess due to a limited number of monitoring wells and significant gaps in the water level time history. To address this challenge, we use a novel imputation technique that leverages Earth observations and machine learning to impute gaps in water level records. We use these more complete datasets to compute a groundwater storage change time series for the basin. We show that groundwater storage is highly correlated to streamflow and that groundwater storage is correlated to rainfall with a three- to four-year delay that appears variable depending on groundwater storage volumes. The tools and relationships we present make it possible for water managers to estimate when streamflows will return to the basin and be more informed to support better management.

Yellow pitahaya is a tropical fruit that has gained popularity in recent years. Natural elicitors are compounds that can stimulate the resistance and quality of fruits. The objective of this study was to evaluate the effects of natural elicitors: methyl salicylate (MeSa), methyl jasmonate (JaMe), salicylic acid (SA) and oxalic acid (OA) at concentrations of 0.1 mM (SaMe and JaMe) and 5 mM (SA and OA), applied to the yellow pitahaya fruits, under greenhouse conditions. After full blossom, 4 applications were made with a frequency of 15 days. At time of harvest and after storage, the following variables were evaluated: firmness (whole fruit), total soluble solids (TSS), total acidity (TA), phenolics and carotenoids (in the pulp), while phenolics, carotenoids, macronutrients and micronutrients were determined in the peel. The results showed that JaMe presented a delay of the ripening process, according to TSS, TA, firmness, and total phenolic compounds results, while MeSa advanced the fruit maturation. Regarding the alternative use of the peel as by-product, the application of natural elicitors significantly increased the content of polyphenols, carotenoids, macronutrients and micronutrients in the peel, which can be used as a bioactive compound in the food industry. In conclusion, the results indicate that natural elicitors can be an alternative to improve the quality and shelf life of yellow pitahaya fruits.

Background: the nature of alpha-D-mannose - natural aldohexose sugar, C-2 glucose epimer, whose intended use is for preventing urinary tract infections - in the interaction with E. coli is addressed in order to drive the issue of its regulatory classification as a medicinal product or medical device. Methods: PRISMA systematic review approach was applied; Delphi Panel method used to target consensus on statements retrieved from evidence. Results: Based of regulatory definitions and research evidences, the mechanism of D-mannose does not involve a metabolic or immunological action while there is an uncertainty regarding the pharmacological action. Specific interaction between the product and the bacteria within the body occurs, but its nature is inert: it does not induce a direct response activating or inhibiting body processes. Moreover, the action of D-mannose takes place, even if inside the bladder, outside the epithelium on bacteria that have not yet invaded the urothelial tissue. Therefore, its mechanism of action is not directed to host structures but to structures (bacteria) external to the host's tissues. Conclusions: From a regulatory perspective, D-mannose maintains the current medical device classification: new regulations and legal judgments can add further considerations. From a pharmacological perspective, research is driven versus synthetic mannosides: no further considerations are expected on alpha-D-mannose.

In the contemporary accelerated pace of life, emphasizing the importance of sleep quality is essential for enhancing overall well-being and health. This study investigates the link between poor sleep quality and key factors affecting wellness, such as mental health and eating disorders. Through a cross-sectional analysis involving 407 participants, utilizing established measures including the Depression Anxiety Stress Scale (DASS-21), the Eating Disorder Examination Questionnaire Short (EDE-QS), and the single-item Sleep Quality Scale (SQS), data was collected and analyzed using SPSS v28 and R-Statistics. The findings reveal a significant correlation (p&lt;0.05) between DASS-21, EDE-QS, and SQS, indicating that individuals experiencing poor sleep quality exhibit higher levels of depression, anxiety, and stress. Furthermore, multinomial logistic regression analysis highlights low sleep quality as a risk factor for both mental health (OR: 1.071, 95% CI: 1.042, 1.102, p&lt;0.05, low vs. high sleep quality), and eating disorders (OR: 1.047, 95% CI: 1.004, 1.092, p&lt;0.05, low vs. high sleep quality). Overall, these results underscore the critical role of sleep quality in mental health and suggest insomnia as a predictive factor for both poor mental well-being and disordered eating habits. Further research through randomized controlled trials is warranted to validate the findings of this cross-sectional study.

Early childhood may be a stressful period for families with a significant impact on parents’ mental health and the child’s healthy development. The goal of the SKKIPPI cohort study was to assess the occurrence and determinants of psychosocial stress and mental health disorders in parents as well as in their offspring in early childhood in three German regions. Based on random samples from three residents' registration offices, parents with infants up to 12 months of age at the time of sampling, were invited to participate in the study. A screening online questionnaire was newly developed, available in four languages, to assess common psy-chosocial stressors and mental health problems of parents with small children. The study enrolled 4,984 mothers and 962 fathers. The most common potential psychosocial stressors at baseline were professional problems (mothers 22%, fathers 33%), lack of social sup-port (20%, 14%), and severe, negative experiences in childhood (22%, 16%). Obses-sive-compulsive thoughts (21%, 16%), depressive (9%, 9%) and anxiety symptoms (11%, 7%) were the most frequently reported mental health problems by both parents. Regulatory prob-lems of the child were reported by between 1.5% and 5.1% of parents. The SKKIPPI study showed that a substantial proportion of parents are burdened by psychoso-cial problems and suffer from mental health problems in the first years after birth. Early pre-ventive and low-threshold support measures should be available in the health and social care system. The newly developed questionnaire can be used to screen in the relevant populations in order to avoid disturbances in the mother-child attachment.

Multifunctional landscapes are complex systems that integrate biophysical, cultural-historical and socio-economic components into unique territorial structures and regional ensembles. Facing increasing pressures generated by urbanization, climate change and overexploitation of natural resources, assessing the sustainability of these landscapes has become an urgent priority. The present research is based on the development and parametrization of a new tool for evaluating the sustainability of multifunctional landscapes that aims to measure the level of biocultural resilience of a landscape, integrating biological, cultural and socio-economic indicators in a single analytical framework. This index, called the biocultural resilience index (BRI), provides a holistic perspective on the dynamics of landscapes, allowing the identification of vulnerability areas and the development of conservation and sustainable management strategies. The evaluation of the of multifunctional landscapes sustainability requires a comprehensive approach that has to integrate both biological aspects, such as biodiversity and ecosystem health, as well as identity and cultural aspects, such as cultural value and the relationship of the local communities with the environment. In this context, this study highlights the fact that the development of appropriate tools and methods for assessing and monitoring the sustainability of multifunctional landscapes becomes essential for their sustainable management and for protecting the benefits they offer to society. Our findings show that the biocultural resilience index (BRI) can be used in a variety of contexts and fields, including spatial planning, biodiversity conservation, sustainable rural development and ecotourism. In the meanwhile, this index offers a robust and flexible analytical framework, adaptable to the needs and particularities of different regions and communities.

With a view to understand and resolve the complexity of the food matrix, ohmic technologies alone or in combination were extensively employed. In this sense, the newest developments and advances of proteomics, metabolomics, lipidomics whith their unique benefits could simplify and understand the link between physiological and pathological activities in biology, physiology, pathology, and food science and processing. This review aims to briefly introduce the basis of proteomics, metabolomics, lipidomics, then expansively review their impact on the assessment of meat quality and safety. Here, also, we discuss the application of proteomics, metabolomics, lipidomics for the authentication and adulteration of meat and meat derivatives from different sources, and provides some perspectives regarding the use of emerging techniques such as rapid mass spectrometry (MS) and non-invasive measurements for the analysis of meat quality and safety. This paper summarizes all significant investigation in these matters, and underlines the advances in analytical chemistry technologies and meat science areas. By emphasizing the requirement for additional examinations, this paper attempts a comprehensive knowledge of “foodomics” and their potential to improve their employment in meat science.

Many farms are replacing the lighting with light emitting diode (LED) bulbs because of the technological modernization. We aimed to investigate the effects of incandescent light (IL) and LED lighting on Cobb500 broiler chickens for six weeks. Production parameters (body weight, feed consumption, feed conversion ratio), calculated slaughter values (yield%, relative breast%, thigh%) and breast meat quality parameters (pH at 45 min and 24 h postmortem, color, drip loss, kitchen equipment losses, shear force, meat composition) were recorded. Non-stop recordings were used to analyze the behavior of the birds in several periods of the rearing. LED group was significantly better in body weigh parameter between week 1-5 and feed conversion ratio between week 2-3. The most significant difference in behavior was observed in the middle of the rearing period. The chickens in the LED group spent more eating time, drinking time, interacting, and resting less. There was no difference in the meat quality parameters, only shear force was significantly lower in the LED group (1781.95±0.33 g/s vs. 2098.82±0.42 g/s). Based on our results, LED lighting can bring positive changes in animal production efficiency, behavior, and important characteristics for meat consumers.

The main goal of this study was to evaluate sugarcane bagasse ash as a partial cement replacement material. Sugarcane bagasse ash is a by-product of fuel blending in the sugar industry. Yet all economic sugar is obtained after extraction from the cane. The disposal of the discharged waste in agriculture causes environmental problems in the sugar industry. The cement industry also creates environmental problems due to carbon dioxide emissions during cement manufacturing. Initially, bagasse ash samples were collected from the rubble of the Arjo Didessa sugar factory. The crude bagasse ash was sieved with a sieve size of 250µm. The strength of grade C-25 concrete was designed using five different concrete mixture proportions ranging from 5 to 20% cement by weight, including a water-cement ratio of 0.45. Impact strength tests were conducted at 7, 14, 21, and 28 days of age for each replacement ratio. For the experimental work, a total of 60 cubic concrete specimens were cast for compressive strength tests, and 15 cylindrical concrete specimens were cast for water absorption tests. Working compressive strength results indicated that bagasse ash could replace up to 5% of ordinary Portland cement concrete.

We propose a partial information decomposition based on the newly introduced framework of causal tensors, i.e., multilinear stochastic maps that transform source data into destination data. The innovation that causal tensors introduce is that the framework allows for an exact expression of an indirect association in terms of the constituting, direct associations. This is not possible when expressing associations only in measures like mutual information or transfer entropy. Instead of a priori expressing associations in terms of mutual information or transfer entropy, the a posteriori expression of associations in these terms results in an intuitive definition of a nonnegative and left monotonic redundancy, which also meets the identity property. Our proposed redundancy satisfies the three axioms introduced by Williams and Beer. Symmetry and self-redundancy axioms follow directly from our definition. The data processing inequality ensures that the monotonicity axiom is satisfied. Because causal tensors can describe both mutual information as transfer entropy, the partial information decomposition applies to both measures. Results show that the decomposition closely resembles the decomposition of other another approach that expresses associations in terms of mutual information a posteriori. A negative synergistic term could indicate that there is an unobserved common cause.

Background: The pandemic caused by the SARS-CoV-2 virus demonstrated the importance of prevention through a healthy diet and lifestyle, the most vulnerable people being those with severe chronic conditions, those who are overweight, and those with an unbalanced immune system. Methods: The evaluation of the eating habits and lifestyle of the Romanian population in the post-pandemic period was carried out based on a cross-sectional observational study with the help of a questionnaire. Results: 4704 valid answers were registered (3136 female and 1568 male respondents). Among the respondents, most of them belong to the young population, 2892 between the ages of 18 and 40, i.e., 61.5%. Most male respondents are overweight (1400) and obese (780). Most respondents indicated a tendency to consume 1-2 meals per day irregularly (p=0.6167). Only 974 respondents adopted a healthy diet, and 578 a healthy lifestyle. Conclusion: The present study reports low adherence to a healthy diet (20.7%) and healthy lifestyle (12.28%), especially among the young population (&lt; 30 years). In the current context, it reports a reduced tendency to consume vegetables and fruits among the population, below the daily average recommended by the nutrition guidelines, a tendency towards sedentary behavior, and even deficient hydration of some of the respondents; these negative aspects can create a long term a series of nutritional and psycho-emotional imbalances. Our results evidence that complex surveys among the population are regularly required to investigate nutritional or lifestyle deficiencies; moreover, it could be helpful in further educational measures in nutrition, food, and environmental safety.

Honey is a sweet substance extensively consumed in the world for its nutritional and healthy properties. However, residues of pesticides and environmental contaminants can compromise its quality. For this reason, the physicochemical parameters, and the organic contamination of monofloral and multifloral honeys from three regions of Algeria (Tiaret, Laghouat and Tindouf) were monitored to evaluate the quality of honey and the safety for consumers. In general, the results obtained from the physicochemical analyses were in line with the EU standards. In terms of contamination, pesticides authorised and used in Algerian agriculture (matalaxyl-M and cyromazine), as well as banned pesticide (carbaryl), were found in almost all the samples. However, only the concentration of cyromazine was higher than the relative EU maximum residue levels. PCB 180, PCB 189, anthracene, fluorene and phenanthrene were mainly detected. All the honeys show traces of DiBP, DBP, DEHP and DEHT, but no traces of bisphenols were found. Moreover, the dietary exposure assessment shows that a small amount of Algerian honey can be safely consumed. Overall, data from this study should motivate the Algerian government to enhance their monitoring activities in beekeeping and to find solutions for implementing more sustainable agricultural practices harmonizing with the international legislation.

The paper delineates the developed vision system of the UR5 cobot and the operating algorithm of the robotic quality control station. The hardware-software architecture of the developed robotic station was shown, consisting of a UR5 cobot equipped with a web camera and a stationary industrial camera with a lighting system. Image processing and analysis algorithms were described, the method of control and communication between the station components was discussed, and two operating scenarios were presented as a single robotic station and a robotic line. Based on the results obtained, the level of measurement noise, accuracy, and repeatability of the developed vision system were estimated.

Wheat is used for making many food products due to its diverse quality profile found among different wheat classes. Since laboratory analysis of these end-use quality traits is costly and time-consuming, genetic dissection of the traits is preferential. This study used a genome-wide association study (GWAS) of 10 end-use quality traits, including kernel protein, flour protein, flour yield, softness equivalence, solvent’s retention capacity, cookie diameter, and top-grain, in soft red winter wheat (SRWW) adapted to US southeast. The GWAS study included 266 SRWW genotypes that were evaluated in two locations over two years (2020-2022). A total of 27,466 single nucleotide markers were used and a total of 80 significant marker-trait associations were identified. There were 13 major effect quantitative trait loci (QTLs) explaining &gt; 10% phenotypic variance out of which 12 were considered as novel. Five of the major effect QTLs were found to be stably expressed across multiple datasets, and four showed associations with multiple traits. Candidate genes were identified for eight of the major-effect QTLs including genes associated with starch biosynthesis and nutritional homeostasis in plants. These findings increase genetic comprehension of these end-use quality traits and could potentially be used for improving the quality of SRWW.

In cutting processes tool condition affects the quality of the manufactured parts. As such an essential component to prevent unplanned downtime and to assure machining quality is having information about the state of the cutting tool. The primary function of it is to alert the operator that the tool has reached or is reaching a level of ware beyond which behavior is unreliable. In this paper the tool condition is being monitored by analyzing the electric current on the main spindle via an artificial intelligence model utilizing a LSTM neural network. In the current study the tool is monitored while working on a cylindrical raw piece made of AA6013 aluminum alloy with a custom polycrystalline diamond tool, for the purposes of monitoring the ware of these tools. Spindle current characteristics were obtained using external measuring equipment to not influence the operation of the machine included in a larger production line. As a novel approach, an artificial intelligence model based on a LSTM neural network is utilized for the analysis of the spindle current obtained during a manufacturing cycle and assessing the tool ware range in real time. The neural network was designed and trained to notice significant char-acteristics of the captured current signal. The conducted research serves as a proof of concept for use of a LSTM neural network-based model as a method of monitoring the condition of cutting tools.

Water quality assessment in pastoral of Tibetan Plateau, which is water sources for about 40% of world's population and the runoff-yield area of Yellow rivers, is very important. In this paper, Xiahe county which belongs to Tibetan Plateau pastoral was investigated. Six parameters(via, chloride, COD, ammonia nitrogen, nitrate, fluoride, sulfate) were selected to assess the water quality and health degree by using fuzzy comprehensive evaluation methods. The hydrochemical type in surface water was of HCO3--Mg2+-Ca2+ type. The cations and anions in surface water were mainly from weathering and dissolution of carbonate rock. Results showed that the water quality in all 69 sampling sites was all of class Ⅰ. The integrated health degree reached more than 0.85 and the health rate were 100%. Although ammonia nitrogen was regarded as the main contamination factor, but it had a little effect on the entire body of water. Overall, the surface water qualities of most samples in Xiahe County was good condition.

Artificial intelligence (AI) is increasingly being used to improve the quality control of point-of-care diagnostics. This is caused by a number of factors, including the following: 1. AI can accelerate and improve testing accuracy. In comparison to humans, AI technology can review data more quickly and precisely, reducing errors and improving overall quality assurance. 2. When it comes to improving POC test findings on healthcare issues such as infectious diseases or medical crises such as heart attacks, AI can be used for sophisticated predictive analytics and modeling that aid in better decision-making. 3. Artificial intelligence facilitates process automation, increasing productivity and lowering labor costs in labor-intensive tasks such as testing and analyzing samples collected at point-of-care facilities. 4. The use of AI enables organizations implementing these solutions to gain insights from large volumes of raw diagnostic data generated faster and more accurately, allowing them to build solid frameworks around preventive care initiatives and significantly influence public health outcomes.5. Artificial intelligence (AI) has been demonstrated to be a useful tool for real-time monitoring systems that identify any problems with test results early so that they can be corrected before affected patients receive inaccurate diagnoses or treatment plans based on false information provided by diagnostic tests performed at points of care such as clinics or hospitals.Using these technologies would allow healthcare organizations to spend less on labor while still receiving exact diagnoses and rapid treatment delivery at a fraction of the cost that manual approaches required earlier.

Cell-culture meat is a novel concept to replace traditional meat produced from animals, and to satisfy rising food demands due to the world population growth. It is still a young field and requires to solve technical issues including cell sources and types, efficient culture for large scale production, taste and texture for customer satisfaction. The current review summarized traditional beef meat production and evaluation methods for customer satisfaction. In particular, serum biomarkers for beef meat evaluation are discussed, which can be applicated for cell-culture meat production.

Wastewater-based surveillance has emerged as an important method for monitoring SARS-CoV-2. This study investigated the presence of SARS-CoV-2 in wastewater in Zambia. We conducted a longitudinal study in the Copperbelt and Eastern provinces of Zambia from October 2023 to December 2023 during which 155 wastewater samples were collected. The samples were subjected to three different concentration methods, namely bag-mediated filtration, skimmed milk flocculation, and polythene glycol-based concentration assays. Molecular detection of SARS-CoV-2 nucleic acid was conducted using real-time PCR. Whole genome sequencing was conducted using Illumina COVIDSEQ assay. Of the 155 wastewater samples, 62 (40%) tested positive for SARS-CoV-2. Of these, 13 sequences of sufficient length to determine SARS-CoV-2 lineages were obtained and two sequences were phylogenetically analyzed. Various Omicron subvariants were detected in wastewater including BA.5, XBB.1.45, BA.2.86, and JN.1. Some of these subvariants have been detected in clinical cases in Zambia. Interestingly, phylogenetic analysis positioned a sequence from the Copperbelt Province in the B.1.1.529 clade, suggesting that earlier Omicron variants detected in late 2021 could still be circulating and may not have been wholly replaced by newer subvariants. This study stresses the need for integrating wastewater surveillance of SARS-CoV-2 into mainstream strategies for monitoring SARS-CoV-2 circulation in Zambia.