A procedure, dedicated to superconductivity, is extended to study the properties of interacting electrons in normal metals in the thermodynamic limit. Each independent-electron band is shown to split into two correlated-electron bands. Excellent agreement is achieved with Bethe's wave-function for the one-dimensional Hubbard model. The groundstate energy, reckoned for the two-dimensional Hubbard Hamiltonian, is found to be lower than values, obtained thanks to the numerical methods. This analysis applies for any spatial dimension and temperature.

The work aims to develop an electromagnetic shielding measurement methodology and design an electromagnetic shielding effectiveness test setup for thin sheet material testing. In brief, multiple shielding effectiveness standards are described and analyzed in the thin sheet material testing framework. Two types of the developed shielding effectiveness test probe in high and low-frequency ranges are validated comprehensively. Extensive descriptions and data of developed testing methodology are also reported.

Convolutional Neural Networks (CNNs) present drawbacks for modeling geometric transformations, such as scaling and rotation, caused by the convolution operation’s locality. Deformable convolution (DCON), a mechanism that substitutes standard convolution, increasing the receptive field to capture relevant features, is a promising approach to solve this drawback and improve the robustness of CNNs. However, the optimal way to replace the standard convolution with its deformable counterpart in a CNN model is unclear. In this study, we clarify this aseveration by conducting several experiments using deformable convolutions applied in the layers that conform a small four-layer CNN model. We also use deformable convolutions on the four-layers of several ResNet CNNs with depths 18, 34, 50, and 101. The models were tested in binary balanced classes with 2D data for image classification: Cats & Dogs, EyesPACS, Spyders & Chickens, and Shapes. After this testing, we evaluated DCON in 3D data for action recognition: UCF101 and Human2 (a dataset we compiled to control movement, clothing and background). The contribution of this research lies in a guideline to use DCON. It can be summarized as follows: if DCON is used on the first layers of the proposal of model (with simple features), the computational resources expressed as the quantity of Flops will tend to increase and produce bigger misclassification than the standard CNN. However, if the DCON is used at the end layers, the quantity of Flops used in the training and testing will decrease, and the classification accuracy will improve by up to 20% about the base model. Moreover, it gains robustness when using deformable convolutions because it can adapt to the region of interest. Also, the best kernel size of the DCON is three. It showed better results than size five. In the last case, the quantity of Flops increase quadratically, but their performance does not increase significantly. With these results, we propose a guideline to use the DCON and contribute to understanding the impact of DCON on the robustness of CNNs.

This paper presents an interpretable support vector machine (SVM) and its application to rehabilitation assessment. We introduce the concept of nearest boundary point to standardize the one-class SVM decision function and determine the shortest path for data from abnormal cases to become those from normal cases. This analytical approach is computationally simple and provides a unique solution. The nearest boundary point of abnormal data can also be used to analyze the cause of abnormal classification and indicate countermeasures for normalization. These properties render the proposed interpretable SVM valuable for medical assessment applications and other problems that require careful consideration of classification results for treatment. Simulation and application results demonstrate the feasibility and effectiveness of the proposed method.

In this paper, we studied the problem of early detection of natural phenomena associated with the formation of severe floods and the possibility of constant monitoring of their occurrence. The test object for the study was severe floods on the Crimean Peninsula, which occurred due to heavy rainfall in the summer of 2021. Based on the selected satellite and other data related to this period, an analysis carried out and key atmospheric objects identified, according to the proposed algorithm for their identification and grouping. Based on the results of the work, a positive conclusion made on the issue of their use to identify the likelihood of natural disasters that could lead to floods. In addition, the authors proposed to develop a portal for collecting and processing a large amount of satellite data related to flood prevention and monitoring the development of such processes, and stressed the need to create it.

The human eye is a vital source of collecting information worldwide via daily observation. The computer science area recognizes it in research as a human-computer interaction. Human blink is an integral part of this observation as a research topic. Several studies have been conducted on eye blinking and left-right eye movements. Previous studies conducted on the eye blink consider the availability of hardware devices high in the budget, high Precision, and low light expo-sure, unlike our study, which uses low-budget devices as simple as a webcam and more versatile usable techniques, incredibly both dim and high light to name a few. This study offers the observational approach via ResNet101v2, VGG-19, and Convolution Neural Network (CNN) architectures. Outperforming both VGG-19 and CNN in this study, ResNet101v2 achieves an impressive accuracy of 98.2%. In contemporary times, deep learning in AI is taking an advanced form. This study attempts to provide a new insight into the real-world implementation of the eye blink.

Examining contemporary developments and cutting-edge approaches in the field, this literature review explores how antenna design for transmission lines is changing. Review findings are compiled from a variety of academic sources, including pertinent technical reports published as recently as 2018, conference papers, journal articles, and reports. A variety of antenna topologies suited for transmission lines are evaluated in this paper, including microstrip, slot, and patch antennas, with a focus on theoretical frameworks and practical implementations. This overview clarifies the complex relationship between antenna design and transmission line characteristics by looking at important factors like impedance matching, bandwidth, and radiation pattern management. Notable developments in materials, fabrication methods, and numerical simulations are also examined and their effects on antenna performance explained. Through a comprehensive analysis of the literature, this review offers valuable insights into the state-of-the-art antenna design practices for transmission lines, facilitating informed decision-making and inspiring future research endeavors in this field.

Conductive hydrogels combine the properties of both hydrogels and electrical conductivity, making them soft, flexible, and biocompatible. These properties enable them to conform to irregular surfaces, stretch and bend without losing their electrical conductivity, and interface with biological systems. Conductive hydrogels can be utilized as conductive traces, electrodes, or as a matrix for flexible electronics. Exciting applications in sensors, tissue engineering and human-machine interaction have been demonstrated worldwide. This review comprehensively covers the progress in this field, focusing on several main aspects: functional materials, performance improvement strategies, and wearable applications in human-related areas. Furthermore, the major approaches and challenges for improving their mechanical properties, conductivity, and long-term stability are systematically summarized.

Emerging data processing techniques brought back into attention the HF range communication as an interesting alternative to third-party solutions for IoT applications, such as data transmission in distributed energy production facilities. The physical size of HF antennas, often comparable to the surrounding objects, require in-situ radiation measurements. Drone-borne measuring systems are already known as a flexible solution, but mostly restricted to higher frequency ranges. In this work, we propose to use an electrically small, folded dipole as a probe for drone-borne measurements on HF antennas. We also propose a calibration approach for the effects related to the near-field zone, and to the drone body proximity. The impact of ground reflection is also investigated. We show that despite its low, realized gain figure such a probe can provide stable results for near-field measurements, even at low input power levels.

Insulated Gate Bipolar Transistor (IGBT) may convey high current and sustain high breakdown voltages; it may provide high power control. In a sense, how IGBT demonstrates the capability of power control was not specifically described, and the equivalent bipolar junction transistors (BJT) activated by an applied bias to the insulated gate is intriguing. As seen in Figure 1, IGBT shows an equivalent circuit structure containing two types of BJT, (NPN-type Bipolar transistor and PNP-type Bipolar transistor), which can be modeled as diode-associated transistor. Apparently, as a bias applies to the controlling gate, the channel beneath the gate oxide gets strongly inversed and turns out to be conductive just like what happens on metal-oxide-silicon field effect transistor (MOSFET), which provides necessary igniting currents to both BJTs and thus causes high current gain flowing through them-selves from the bottom. A proposed and renewed formula provides addressing the above scenario and successfully fitting the measured data that forms the characteristic curves. Some parameters in the proposed formula, which includes size and mobility associated constant, threshold voltage, and Early-Voltage-related lambda for MOSFET, explain and explore the underlying physics. IGBT thus enjoy high input impedance and high current gain due to MOSFET (Insulated Gate) and BJT, respectively. This formula combines both merits of MOSFET and BJT in order to fit the measured data. Indeed, the formula intimately fits IGBT electrical characteristic curves, and thus may be qualified and served as a model. The new model is then advisable for designing power integrated circuit to exactly achieve power saving, power control, and power efficiency.

The electric vehicle (EV) industry challenges battery joining technologies by requiring higher energy density both by mass and volume. Improving the energy density via new battery chemistry would be the holy grail but is seriously hindered and progresses slowly. In the meantime, alternative ways, such as implementing more efficient cell packaging by minimizing the electrical resistance of joints are of primary focus. In this paper we discuss the challenges associated with the electrical characterisation of laser soldered joints in general, and the minimization of their resistive losses, in particular. In order to assess the impact of the joint resistance on the overall resistance of the sample, the alteration in resistance was monitored as a function of voltage probe distance and modelled by finite element simulation. The experimental measurements showed two different regimes: one far from of the joint area and another in its vicinity and within the joints cross section. The presented results confirm the importance of the thickness of the filler material, the effective and the total soldered area, and the area and the position of the voids within the total soldered area in determining the electrical resistance of joints.

Ultrasound (US) scans of the inferior vena cava (IVC) provide useful information on the volume status of a patient. However, their investigation is user-dependent and prone to measurement errors. An important technical problem is the objective difficulty in studying a very compliant blood vessel like IVC, which makes large respirophasic movements and shows a complicated three dimensional geometry. Using bi-dimensional (2D) B-mode views either in long or short axis has improved the characterization of IVC dynamics compared to a measurement along a single direction (M-mode). However, specific movements of the IVC can challenge also the information provided by these 2D sections. Thus, these two orthogonal views, provided by an US system in X-plane, are here integrated by an innovative method. It is tested on simulated videos of the IVC performing complicated movements, that are compensated by the new method, overcoming the biased measurements provided by 2D scans. The method is then applied on example experimental data.

Toll plaza optimization is essential for improving traffic flow and easing congestion on road networks. This study aims to suggest and assess potential optimization solutions for the Peshawar toll plaza, considering variables like traffic volume, toll-collecting effectiveness, and customer facilitation. Different resources are used for data collection, like the National Highway Authority of Pakistan. Physical data is collected from the established Toll Plaza of Peshawar, along with the development of each line. The goal of this study is to suggest and assess potential optimization solutions for the Peshawar toll plaza, considering variables like traffic volume, toll-collecting effectiveness, and customer happiness. The analysis of present traffic patterns, the detection of bottlenecks, and the creation of plans to ease congestion and enhance overall traffic flow are all part of the optimization process. The approaches used in this study include data analysis, simulation, and traffic modeling. PTV VISSIM is software for transportation planning, design, and analysis. The simulations consider various conditions, such as variable traffic volumes, toll collection methods, and lane configurations. When comparing the different optimization strategies, performance indicators like trip time, latency, and queue length are utilized to determine which approach is practical. Waiting time Vs. Existing each lane, etc, is explained. In the end, comparing queue lengths and throughput across different lane scenarios shows that maximizing throughput with existing lanes yields up to 45% improvement with E-tag lanes, 40% with existing E-tag lanes, 38% with E-tag plus additional toll and cash lanes, 32% with three cash lanes, and 28% with two E-tag lanes. Failure to regularly monitor and adjust the existing lane pattern scenario based on traffic patterns can lead to queues being 20% longer. Without proactive evaluation and optimization, there is a potential 63% opportunity for queue length improvement

Airborne Frequency Diversity Array (FDA) radar operating at a high pulse repetition frequency encounters severe range-ambiguous clutter. The slight frequency increments introduced by the FDA result in angle and range coupling. Under these conditions, conventional space-time adaptive processing (STAP) often exhibits diminished performance or fails, complicating target detection. This paper proposes a method combining elevation oblique subspace projection with azimuth-Doppler STAP to suppress range-ambiguous clutter. By analyzing the relationship between elevation frequency and range, the proposed method compensates for quadratic range dependence. Through the construction of an elevation oblique subspace projection technique, an elevation adaptive filter is used to separate clutter from ambiguous regions. Residual clutter suppression is achieved through azimuth-Doppler STAP, enhancing target detection performance. Simulation results demonstrate that the proposed method effectively addresses range dependence and ambiguity issues, improving target detection performance in complex airborne FDA radar environments.

The review aims to assess fifteen (15) academic literature sources, highlighting the application of machine learning algorithms in the maintenance operations of optical fiber networks. It exhibits the collection of data using PRISMA methodology—Preferred Reporting Item for Systems Review and Meta-Analyses. The application, results, and performance metrics are discussed based on the collected observations, computations, and statistics in the studies, which revealed records of high accuracy degrees ranging from 86% to 98% on average and quality ML models including Neural Networks (NNs), Support Vector Machines (SVMs), and LSTM, as well as deep learning models that disclosed effective results of determining challenges and problems within the optical fiber lines. The review mainly centralized on superior machine learning technologies that surpass traditional techniques in fault detection and localization for improved optical fiber networks’ operations while providing insights into the limitations and challenges encountered in real-world applications of these models, offering a comprehensive perspective on the optical fiber network’s domain.

An easy to implement and cost-effective Fiber Bragg Grating (FBG) sensor interrogation technique based on a ring Erbium-Doped Fiber Laser (EDFL) topology is proposed and experimentally assessed. The FBG sensor is part of the EDFL cavity and must have a central wavelength located within the linear region of the EDF’s amplified spontaneous emission (ASE) spectrum which occurs between 1530 and 1540nm. In this manner, the wavelength-encoded response of the FBG under strain is converted to a linear variation of the laser output power, removing the need for spectrum analysis as well as any limitations from the use of external edge-filtering components. In addition, the laser linewidth is significantly reduced with respect to the FBG bandwidth thus improving the resolution of the system, whereas its sensitivity can be controlled through the pumping power. The performance of the system has been characterized by modeling and experiments for EDF's with different lengths, doping concentrations and pumping power levels. The influence of mode-hopping in the laser cavity on the resolution and accuracy of the system has also been investigated.

The existence of low-cost and accurate tools that can equip the First Responders (FRs) to detect trapped victims and provide insights about their health condition in the aftermath of a disaster, is imperative. To address the problem of detecting trapped victims behind walls or debris, we have developed a tool that exploits an Ultra-Wide Band (UWB) radar sensor for data collection and Machine Learning (ML) algorithms for data analysis. To evaluate the efficacy of our approach, we collected data from nine humans, both in standing and lying down positions. Next, we applied various ML algorithms to the collected dataset for two discrete sub-tasks that are of interest from an FR’s perspective. The first task is the detection of the victim’s presence, where the algorithms attained more than 95% accuracy and F1-Score. The second task is the estimation of the distance between the radar sensor and the victim, where the tool showed an average error of less than 40 cm.

It is of great academic significance to understand how the atomic structure of interfaces and boundaries in materials impacts the magnetic coupling nature across the boundaries and encourage development of state-of-the-art magnetic devices. Here, we carry out a systematic investigation of the atomic and electronic structures of twin boundaries (TBs) in LiFe5O8 thin films and determine their concurrent magnetic couplings using atomic-resolution transmission electron microscopy and atomistic first-principles calculations. The results show ferromagnetic or antiferromagnetic coupling can exist across the different TBs in LiFe5O8 (LFO) thin films and electrical structures within a few atomic layers directly rely on the TB atomic core structures. Uncovering one-to-one relationship between the magnetic properties of individual TB and the local atomic structures will clarify a thorough comprehension of numerous fascinating magnetic properties of commonly utilized magnetic materials, which will undoubtedly encourage the progress of sophisticated magnetic materials and devices.

High-precision displacement sensing has been widely used across from both scientific researches and industrial applications. The recent interests in developing micro-opto-electro-mechanical systems (MOEMS) have given rise to an excellent platform for miniaturized displacement sensors. Advancement in this field during past years is now yielding integrated high-precision sensors which show great potential in applications ranging from photoacoustic spectroscopy to high-precision positioning and automation. In this review, we briefly summarize different techniques for high-precision displacement sensing based on MOEMS, and discuss the challenges for future improvement.

In this paper, some characterizations of fuzzifying strong compactness are given, including characterizations in terms of nets and pre -subbases. Several characterizations of locally strong compactness in the framework of fuzzifying topology are introduced and the mapping theorems are obtained.

The paper presents an error model of a measurement chain containing link performing discrete wavelet transform algorithm which is most often the last stage of measurement signal processing. The goal is to determine the uncertainty budget of the input quantities of the wavelet transform algorithm. The error model takes into account parts of analog, analog-to-digital and digital processing, describing the properties of subsequent fragments of the chain using their transmittance and processing functions. The proposed model enables the description of both deterministic and non-deterministic properties of signal errors. The proposed model was validated using an example measurement chain created for this purpose.

In multi-objective optimization problems, the optimization target is to obtain a set of non-dominated solutions. Comparing solution sets is crucial in evaluating the performances of different optimization algorithms. The use of performance indicators is common in comparing those sets and, subsequently, optimization algorithms. A good solution set must be close to the Pareto-optimal front, well-distributed, maximally extended and fully filled. Therefore, an effective performance indicator must encompass these features as a whole and must be Pareto dominance compliant. Unfortunately, some of the known indicators often fail to properly reflect the quality of a solution set or cost a lot to compute. This paper demonstrates that the Degree of Approximation (DOA) quality indicator, is a weakly Pareto compliant unary indicator that gives a good estimation of the match between the approximated front and the Pareto-optimal front. Moreover, DOA computation is easy and fast.

The application of artificial intelligence to point-of-care testing (POCT) disease detection has become a hot research field, in which breath detection which detects the patient's exhaled VOCs combined with sensor arrays of Convolutional Neural Network (CNN) algorithms as a new lung cancer detection is attracting more researchers' attention. However, due to low accuracy, high complexity computation and large number of parameters make the CNN algorithms difficult transplant to the embedded system of POCT devices. A lightweight neural network (LTNet) in this work is proposed to deal with this problem, and meanwhile, achieve high-precision classification of acetone and ethanol gases, which are respiratory markers for lung cancer patients. Compared to currently popular lightweight CNN models such as EfficientNet, LTNet has fewer parameters (32K) and its training weight size is only 0.155 MB. LTNet achieved an overall classification accuracy of 99.06% and 99.14% in the own mixed gas dataset and the University of California (UCI) dataset, which are both higher than that of the five existing models’, and it also offers the shortest training (844.38s and 584.67s) and inference time (23s and 14s) in the same validation set. Compared to the existing CNN models, LTNet is more suitable for resource-limited POCT devices.

In this work model of mirror elements equilibrium of the micromechanical components is developed, the behavior analysis of the mirror element of micromechanical mirrors in case changing of control voltages of electrostatic actuators is carried out, an expression for determining the maximum value of deflection voltage at which the snap-down effect will take the following form is obtained in case of the influence of the coefficient of the electrostatic rigidity of electrostatic actuators. The developed equilibrium model of mirror elements and the obtained results of modeling can be used at design of micromechanical mirrors with internal suspensions.

Photovoltaic (PV) technologies are developing rapidly as a result of their ability to reduce energy consumption from conventional sources as well as the growth of global energy expenditures. Nevertheless, several impact categories during the PV panel life cycle occur and some principal sectors are affected. These impact categories are assessed by applying life cycle analysis (LCA) techniques through various software programs, databases and methods. Such analyses of energy technologies are crucial, as they can reveal the occurrence of hazardous emissions at distinct life cycle stages. In the present paper, a PV panel impact assessment through life cycle analysis is carried out. More precisely, a combination of PV technologies—monocrystalline, multicrystalline, copper indium gallium selenide (CIGS), amorphous, and ribbon—is studied. The impact categories of ozone depletion, human toxicity, particulate matter, ionising radiation, photochemical ozone formation, acidification, eutrophication, and ecotoxicity, as well as the sectors of human health, ecosystem quality, and environment, are assessed using the openLCA software, the ecoinvent database, the eco-indicator 99, IMPACT 2002+, ReCiPe, and TRACI methods.

Day by day, the share of renewable energy-based power plants such as offshore wind farms and photovoltaic power plants, in the present-day power systems is escalating. Nevertheless, most of these power-producing facilities have been located quite far away from the load centers. At this stage, HVDC power systems provide satisfactory options due to qualities such as reduced line losses, substantial controllability, and environmental advantages. Nevertheless, unique converter designs are required to combine asynchronous HVDC networks with each other and with already existing high voltage alternating current (HVAC) networks. In this study, based on the above special cases, a unique DC-DC modular multilevel converter (MMC) architecture is presented that provides an excellent solution for both integrating modern asynchronous HVDC networks and integrating these modern HVDC power systems with existing asynchronous HVAC power systems. The mathematical analysis of the recommended DC-DC MMC design has been examined in detail and the power transfer between two asynchronous power grids has been realized in a simulation environment. Efficient bilateral power transmission has been made achievable by the control system. The recommended DC-DC MMC topology has shown to be a highly successful approach, in the interconnection of HVDC power systems, according to the simulation results.

In the ground-based infrared optical remote sensing system, the target signal is very weak due to the dynamic strong light background and the movement of small and small targets. In order to improve the limit detection capability, the background suppression and target enhancement methods are required to be more suitable for this scene. To solve this problem, we first analyze the image features in the current scene, and propose a more perfect point target and noise model. Then, we propose a new WY distribution function based on the Fermi Dirac distribution function, and propose an anisotropic filtering method based on this function, and further suppress the back-ground through the difference results of two steps. Then, based on the distribution function, we further designed an energy concentration accumulation strategy in 9 scale directions, through which the SNR of the target is effectively improved and the suppression ability of the background is enhanced. Through quantitative and qualitative experimental analysis, compared with the same type of algorithms, the proposed method has better robustness against extremely weak targets and dynamic backgrounds.

The numerical implementation of the controllers allows the use of very complex algorithms with ease. However, in practice, due to its proven advantages, the PID controller (and its variants) is widely used in industrial control systems as well as in many other applications that require continuous control. Most of the methods for tuning the parameters of PID controllers are based on time-invariant linear models of the processes, which in practice can lead to poor performance of the control system. The paper presents an application of reinforcement learning algorithms in tuning of PID controllers for the control of some classes of continuous nonlinear systems. Tuning the parameters of PID controllers is done with the help of Twin Delayed Deep Deterministic Policy Gradients (TD3) algorithm which presents a series of advantages compared to other similar methods from Machine Learning dedicated to continuous state and action spaces. TD3 algorithm is an off-policy Actor-Critic based method and was used as it does not require a system model. The presented technique is applied for control of a biotechnological system which has a strongly nonlinear dynamic. The proposed tuning method is compared to the classical tuning methods of PID controllers. The performance of the tuning method based on the TD3 algorithm is demonstrated through simulation illustrating the effectiveness of the proposed methodology.

Pulmonary Embolism (PE) is the obstruction of blood arteries in the lungs by a blood clot. The mortality risk for PE is approximately 30%. Detecting pulmonary embolism in the segmental arteries of the lung is more challenging than in the main arteries and is very prone to being missed. A computer-based approach was created in this work to automatically identify pulmonary embolism in the segmental arteries using computed tomography images. The system's infrastructure includes an enhanced Mask R-CNN deep neural network that has been trained with images containing PE. The network accurately identifies the location of the pulmonary embolism on the computed tomography picture and successfully extracts its borders. The investigation was conducted by generating a local dataset. The study's performance was evaluated using pulmonary embolisms identified manually by the expert radiologist. The sensitivity, specificity, accuracy, dice coefficient, and Jaccard index values for 2130 pictures were 96.4%, 93.5%, 96.1%, 0.96, and 0.90, respectively. The improved Mask R-CNN model has demonstrated superior performance when compared to the traditional Mask R-CNN and U-Net models. This high-performance technology is designed to identify pulmonary embolism and will aid professionals in assessing the size of the embolism.

Digital twins are an emerging technology that could be harnessed for the digitalization of the industry. Steel industry systems contain a large number of electro-hydraulic components, as proportional valves. An input-output model for a novel water proportional cartridge valve is derived from physical modelling based on fluid mechanics, dynamics, and electrical principles. The valve is a two-stage valve with two 2/2-way water proportional valves as the pilot stage and a marginally stable poppet-type cartridge valve as the main valve. The orifice equation, which is based on Bernoulli principles, is approximated by a polynomial which makes parameter estimation easier and makes modelling possible without measuring pressure of the varying control volume situated in the pilot stage part of the valve. Data were collected when the valve was operating as a component in a closed-loop system as part of a press-mill machine in a steel manufacturing plant. Parameter estimation was made by convex optimization with physical constraints to overcome problems caused by poor system excitation. For comparison, a simple linear model was derived and the least squares method used for parameter estimation. A thorough estimation of the parameters relative errors is presented. The model contains 5 parameters related to the design parameters of the valve. The modelled position output is in good agreement with experimental data for training and test data. The model can be used for real time monitoring of the valve’s status by the model parameters. One of the model parameters varies linearly with production cycles. Thus, aging of the valve can be monitored.

The Doppler band compensated by the keystone transform (KT) is limited. Therefore, it needs to be used in conjunction with the Doppler ambiguity compensation function to correct the range migration (RM) caused by maneuvering targets with Doppler ambiguity. However, the KT implemented by sinc interpolation suffers from significant performance loss at boundaries of compensation Doppler bands. Additionally, in a multi-target scenario, KT implementation methods occupy high complexity when the Doppler range of targets spans over two compensation Doppler bands. To address aforementioned issues, this study presents a variable Doppler starting point keystone transform (VDSPKT) method, where a new form of ambiguity compensation function is constructed, turning the Doppler starting point of the compensation band in KT variable. Firstly, the position of the compensation Doppler band is changed from fixed to adjustable as needed, enhancing the flexibility of KT. Crucially, the connection points of the compensation Doppler bands in sinc interpolation are reset, avoiding the performance loss at their boundaries. Also, the compensation band is adjusted to cover the narrow Doppler frequency range caused by targets, significantly improving the computational efficiency. Finally, the simulation results demonstrate that the proposed approach effectively addresses the performance degradation and high computational complexity of KT in the aforementioned scenarios, resulting in a computational load reduced by approximately 50% compared to traditional methods.

Herein, we present the design technique of a resonant rectifier for piezoelectric (PE) energy harvesting. We propose two diode equivalents to reduce the voltage drop in the rectifier operation, a minuscule-drop-diode equivalent (MDDE) and a low-drop-diode equivalent (LDDE). The diode equivalents are embedded in resonant rectifier integrated circuits (ICs), which use symmetric bias-flip to reduce the power wasted for charging and discharging the internal capacitance of a PE transducer. The self-startup function is supported by synchronously generating control pulses for the bias-flip from the PE transducer. Two resonant rectifier ICs, using both MDDE and LDDE, are fabricated in a 0.18 μm CMOS process and their performances are characterized under external and self-power conditions. Under the external-power condition, the rectifier using LDDE delivers an output power POUT of 564 μW and a rectifier output voltage VRECT of 3.36 V with a power conversion efficiency (PCE) of 90.1%. Under self-power conditions, the rectifier using MDDE delivers a POUT of 288 μW and a VRECT of 2.4 V with a corresponding PCE of 74.6%. The result shows that the power extraction capability of the proposed rectifier is 5.9 and 3.0 times higher than that of a conventional full-bridge rectifier.

Lane detection is a foundational technology for autonomous driving systems. It involves identifying the boundaries of lanes on the road and ensuring the vehicle stays within these boundaries. Accurate lane detection is crucial for safety, navigation and traffic management. This paper presents an artificial intelligent based autonomous road lane detection and navigation system for vehicles. The system can detect and analyze road lanes accurately and efficiently in real-time, with frame rates of up to 17 FPS. By utilizing image processing techniques, the system can identify the location and boundaries of road lanes and obstacles on the road and provide accurate and reliable navigation guidance to the driver. The system is integrated with sensors and actuators to provide comprehensive autonomous navigation. The efficiency of the proposed system is demonstrated using accuracy of lane detection on straight and curve lanes covering frames per second and motor of the speed as parameters for assessment. Results show that the proposed system detects lane as entire lane detection, partial lane detection and no detection status on different settings.

Using the example of a generator model with dedicated inertia, a theoretical study of two coupled self-oscillators with capacitive coupling, their sequential single-frequency synchronization, chaos and two-frequency synchronization with an adiabatic change in the magnitude of the coupling between partial self-oscillators was carried out. The parameters of self-oscillators and the values of the coupling coefficient at which the specified operating modes of coupled self-oscillators exist are determined. The results of numerical studies, illustrating the conditions for excitation of single-frequency, chaotic and dual-frequency oscillations in a system of coupled self-oscillators are presented.

The occurrence of chaotic instability of oscillations at the output of a single-stage amplifier on a powerful bipolar microwave transistor when a biharmonic signal is amplified is considered. It has been established that at a high level of the input signal at the output of the amplifier, the signal contains a significant chaotic component. Cases were experimentally studied when the frequency distance between the partial frequency components of a biharmonic signal is close to the gain band and when it is much smaller than this band. It has been established that in the first case, the chaos in oscillations is associated with the emergence of a sequence of trains of a forced oscillatory process with arbitrary initial phases and durations. In the second case, the appearance of a chaotic pedestal is associated with the chaos in the passive underexcited mode of the nonlinear circuit formed by the capacitance of the p-n junction and the input matching circuits of the amplifier stage.

Fractal array antennas are multiband arrays having ultra wide band and space filling facility. But Side lobe levels and large number of antenna elements are the major designing challenges of these arrays. In this paper, design and analysis of octagonal fractal array antenna is investigated with Morse-Thue fractal density tapering technique (MTFDT). Due to the proposed technique, a remarkable improvement has observed in Side lobe levels and thinning of the elements can also be attained at the various iterations of octagonal fractal array antenna. These arrays are analyzed and simulated by MATLAB-15 programming.

Despite soccer popularity, comparatively little scientific information is available concerning the assessment of youth players’ physiological characteristics. The use of medical software integrating wearable sensors to provide accurate and objective data is necessary. In the present study, the objective assessment of physical performance of 128 adolescent soccer players at two timepoints (pre-season and end-season) has been performed. Participants completed a comprehensive test battery including stability, countermovement jumps (CMJ), plyometric jumps (PJ), agility, and quick feet tests. A single Inertial Measurement Unit (IMU) sensor provided quantitative data on various performance metrics. Principal Component Analysis (PCA) reduced the dataset to four principal components (PCs) explaining over 80% of the variance: power (PC1), balance (PC2), speed/agility (PC3), and stiffness (PC4). Paired samples t-test between the two timepoints showed no significant differences in the PCs between the two timepoints, indicating that the training program did not significantly alter the assessed physical attributes. However, subtle individual changes may still inform personalized training adjustments. The study highlights the importance of continuous monitoring and individualized training strategies to optimize athlete performance and reduce injury risk.

For their speed in data processing, low heights and cheapness, patch antennas are important to 5G networks. While there have been improvements in the area of bandwidth and size reduction; however, there are still problems that need to be fixed with regards achieving high data rates as well as wideband operation and compact sizes for 5G applications. In the coming years researchers should concentrate on materials optimization and feeding methods so that they can work efficiently at shorter wavelengths for next-generation systems while still covering all necessary bands.

For the first time, the effect of a significant change in the resistance of the aquatic environment of a population of protozoan microorganisms under the influence of radiofrequency electromagnetic radiation from cell phones has been experimentally studied. The results of the experiment demonstrate the biological nature of the changes occurring in the “water population of protozoa” system, which indicates that the impact of radiation directly affects the cell. This conclusion is confirmed by the same order of magnitude time of information exchange between individual individuals of the population in the calculation and in the experiment. An extremely low concentration of protozoa in the experiment was established, equal to 1000 pcs./liter, at which the indicated effect is observed.An unambiguous dependence of the biological effect in the “water – amoeba population” system on the average power of electromagnetic radiation of cell phones, both in standby mode and in talk mode, has been established. It is concluded that the presented method of changing the physical properties of the aquatic environment of a population of protozoa under the influence of electromagnetic fields can be a model experiment in identifying the mechanisms of interaction of biological systems with electromagnetic radiation, determining the response time of biological systems to external electromagnetic influence, and establishing the degree of influence of radiation in the 4G, 5G ranges.

Heavy rains have created significant threats to human health and life. Floods and other natural disasters, which have a global impact annually, can be attributed to extended durations of intense precipitation. Accurate rainfall predictions are crucial in nations such as Bangladesh, where agriculture is the predominant occupation. The efficiency of machine learning (ML) methods is enhanced by the non-linearity of rainfall, surpassing the effectiveness of other alternative ways. Machine learning techniques show that individual classifiers exhibit worse accuracy than ensemble learning (EL) methodologies. Ensemble Learning techniques are utilized for rainfall prediction and estimating rainfall quantity and daily average temperature to enhance comprehension of the diverse Machine Learning algorithms. This research implements the machine learning techniques and ensemble-based classifier to predict the rainfall occurrence, along with the machine learning regressor models and ensemble-based regressor for the rainfall amount prediction and daily average temperature prediction, using Bangladesh Weather Dataset. The results of the machine learning and ensemble-based models are compared using the Accuracy and F1 score for rainfall occurrence prediction. In contrast, MAE and RMSE evaluation metrics are used for ensemble regressor and regression algorithms for the rainfall amount and daily average temperature prediction. With an accuracy of 83.41% and a recall of 78.17%, the Ensemble Classifier is the best at predicting when it will rain, but its precision of 51.16% stands in for the lowest. The Ensemble Regression model outperforms Linear Regression, Random Forest, and SVR in rainfall amount prediction, with the lowest MAE of 0.36 and RMSE of 0.90. The Ensemble Regression provides the most precise results for daily average temperature prediction with the lowest MAE 0.42 and RMSE 0.54 highlighting its superiority over the other regression models in forecasting temperature with less error. Ensemble approaches consistently lead task performance metrics.

A power factor correction (PFC) rectifier is compulsory for any electronic circuitry connected to the electrical grid. The majority of PFCs that are utilized are based on a step-up converter that supplies high DC voltage at its output terminal. Electric vehicle battery voltage varies from a few hundred to almost a thousand volts. Thus, an additional conversion step is obligatory when designing an all-brand universal charger. This paper presents a new type of front-end versatile step up / down three voltage level PFC. The rectifier can operate in continuous conduction mode or discontinuous conduction mode. First, the rectifier’s principle of operation is described, and then an innovative rectifier is analyzed for continuous and discontinuous conduction modes. Finally, the proposed theory is experimentally validated in a multiplier-less dual loop mode at discontinuous conduction modes. It was shown that although there is no multiplier use in the control circuitry, the power factor is near unity. It was revealed that the rectifier could swing the output voltage from 50 V to 900 V while the input voltage was 230 Vrms. The innovative topology suits any standard PFC rectifier, three-level voltage supplement, and dual-stage low-voltage power supply.

Many fields of human activity benefit from the ability to create images of obscured objects placed behind walls and to map their displacement in a noninvasive way. Usually, imaging devices like Synthetic Aperture Radars (SAR) and Ground Penetrating Radars (GPR) use expensive dedicated electronics which results in prohibitive prices. This paper presents the experimental implementation and the results obtained from an imaging system capable of performing SAR imaging and interferometric displacement mapping of targets located behind walls, as well as 3D GPR imaging using a low-cost general-purpose radar sensor. The proposed solution uses for the RF section of the system a K-band microwave radar sensor module implementing Frequency Modulated Continuous Wave operation. The low-cost sensor was originally intended for simple presence detection and ranging for domestic applications. The proposed system was tested in several scenarios and proved to operate as intended for a fraction of the cost of a commercial imaging device.

The object of study in the article is the auxiliary variable-frequency electric drive onboard of an AC electric locomotive, and more precisely, the structure and parameters of the control system of the active corrector of power factor (ACPF), which is part of the electric drive, as a unit that ensures electromagnetic compatibility of the electric drive with other equipment on board the electric locomotive and catenary and its energy efficiency. The topic of the article's research is the substantiation of the structure of the ACPF control system, the choice of types (transfer functions) of controllers and the calculation of their parameters. The research method chosen was the calculation of the transfer functions of the controllers of the cascaded loops control system, followed by computer simulation using the OrCAD software. The results of simulating a cascaded two loops control system of an ACPF with different types of controllers are presented and analytically compared. It is concluded that it is advisable to use a cascaded two loops control system, containing a voltage control loop and a current control loop. The best results show the simulation when using an aperiodic current controller (A-controller) and a proportional-integral voltage controller (PI-controller). The data obtained serve as the basis for further improvement of the operation of the ACPF by enhancing and optimizing the settings, structure and algorithms of the control system, which, with the selected hardware of power converter unit, will allow the ACPF to perform its functions with a high degree of reliability in an entire range of disturbing and control influences.

The abilities of quantitative description of noise are restricted due to its origin and only the statistical and spectral analysis methods can be applied while an exact time evolution cannot be defined or predicted. It emphasizes the challenges faced in many applications including communication systems where noise can play, on one hand, a vital role impacting signal-to-noise ratio but possessing, on the other hand, unique properties such as infinite entropy (infinite information capacity), exponentially decaying correlation function and so on. Despite the deterministic nature of chaotic systems, the predictability of chaotic signals is limited for a short time window putting them close to random noise. In this article, we propose and experimentally verify an approach to achieve Gaussian-distributed chaotic signals by processing the outputs of chaotic systems. The mathematical criteria, on which the main idea of the study is based on, is the Central Limit Theorem which states that the sum of a large number of independent random variables with similar variances approaches a Gaussian distribution. The study involves more than 40 mostly three-dimensional continuous-time chaotic systems (Chua’s, Lorenz’s, Sprott’s, memristor-based, etc.) whose output signals are analyzed according to criteria that encompass the probability density functions of a chaotic signal itself and its envelope and phase, statistical and entropy-based metrics such as skewness, kurtosis, and entropy power. We found that two chaotic signals of Chua’s and Lorenz’s systems exhibited superior performance across the chosen metrics. Furthermore, our focus extended to determining the minimum number of independent chaotic signals necessary to yield a Gaussian-distributed combined signal. The analytic and experimental results indicate that the sum of at least three non-Gaussian chaotic signals closely approximates Gaussian distribution. It allows generation of reproducible Gaussian-distributed deterministic chaos by modeling simple chaotic systems.

The enormous growth in the penetration of electric vehicles (EVs), has laid the path to advancements in the charging infrastructure. Connectivity between charging stations is an essential prerequisite for future EV adoption to alleviate users’ “range anxiety”. The existing charging stations fail to adopt power provision allocation and scheduling management. To improve the existing charging infrastructure data based on real-time information and availability of reserves at charging stations could be uploaded to the users to help them locate the nearest charging station for an EV. This research article focuses on an a interactive user application developed through SQL and PHP platform to allocate the charging slots based on estimated battery parameters, which uses data communication with charging stations to receive the slot availability information. The proposed server-based real-time forecast charging infrastructure avoids waiting times and its scheduling management efficiently prevents the EV from halting on road due to battery drain out. The proposed model is implemented using a low-cost microcontroller and the system etiquette tested.

Wireless Powered Communication Networks (WPCN), which has attracted much attention of researchers, also been recently recommended in 5^th generation (5G) wireless networks. With the help of the WPCN, the reliability and battery life of wireless low-power devices can be improved. In this paper, we investigate throughput and ergodic capacity in WPCN-assisted amplify-and-forward (AF) relaying system, considering two transmission modes including delay-tolerant and delay-limited. As important achievement, we propose symmetric energy harvesting protocol, namely time power switching relaying (TPSR) in order to find maximal throughput. In particular, both time switching and power switching coefficients in this schemes are considered. Unlike most of the previous works, we further focus on impact of outdated channel state information (CSI) in this WPCN. In order to evaluate information processing efficiency, the performance can be substantially improved by optimally harvesting time and power coefficients of the received signal at relay node for energy and information extraction, and by deploying several scenarios. By deploying Monte Carlo simulation, it is confirmed that the system performance is more sensitive to CSI estimation error, noise variance, signal-to-noise ratio (SNR) and resulting in other reasonable computations of TPSR need be deployed to obtain QoS requirement.

Starting from the fact that one of the global control strategies of the Permanent Magnet Synchronous Motor (PMSM), namely the Direct Torque Control (DTC) type control strategy, is characterised by the fact that the inner flux and torque control loop usually uses hysteresis ON-OFF type controllers and the oscillations introduced by them have to be cancelled out by the outer speed loop controller (which is usually a PI speed controller and whose performance is good around the global operating points and for relatively small variations of the external parameters and disturbances caused in particular by the load torque variation), while retaining the advantages of the DTC strategy, this paper presents the improvement of the performance of the PMSM sensorless control system using Proportional Integrator (PI), PI Equilibrium Optimizer Algorithm (EOA), Fractional Order (FO) PI, Tilt Integral Derivative (TID) and FO Lead-Lag for constant flux, and Sliding Mode Control (SMC) and FOSMC for variable flux. The performance indicators of the control system are the usual ones: response time, settling time, overshoot, steady-state error and speed ripple, plus another one given by the fractal dimension (FD) of the PMSM rotor speed signal, and the hypothesis that the FD of the controlled signal is higher when the control system provides better performance is verified. The paper also presents the basic equations of the PMSM, based on which the synthesis of integer and fractional controllers, the synthesis of an observer for estimating the PMSM rotor speed, electromagnetic torque and stator flux are presented. The comparison of the performance of the proposed control systems and the demonstration of the parametric robustness are performed by numerical simulations in Matlab/Simulink using Simscape Electrical and Fractional Order Modelling and Control (FOMCON). Real-time control based on an embedded system using a TMS320F28379D controller demonstrates the good performance of the PMSM sensorless control system based on the DTC strategy in a complete hardware-in-the-loop (HIL) implementation.

Protection suit is vital for fireman’ safety. Traditional protection suit just physically protects fireman from empyrosis, but can not locate the body injury position from the impact debris. Herein, we present a wearable impact debris positioning system for fireman protection suit alarming based on accelerometer array. The wearable piezoelectric accelerometers with distribute regularly on the suit to detect the vibration on different body parts, which is conducive to positioning injured body parts. In addition, the injured parts can be displayed on the dummy body model on the upper computer with a higher localization accuracy of 4 cm. The positioning alarm system has a rapid response time of 0.11ms attributing to smart signal processing method. This work provides a reliable and smart method for locating and assessing the body injury position from the impact debris, which is significant for fire disaster commander to rescue injured fireman in time.

In a software-defined radar (SDR) system, most of the signal processing usually implemented in hardware is implemented by software, thus allowing for higher flexibility and modularity compared to conventional radar systems. However, the majority of SDR demonstrators and proofs-of-concept reported in the open literature so far have been based on simple antenna systems. As a result, the full potentialities of an SDR approach have not been completely exploited yet. In this work, we propose a flexilbe antenna module to be integrated into an active electronically scanning array (AESA) with controlled sidelobe level over a wide angular range, exhibiting polarization reconfigurability with low cross-polarization level and high isolation. For this purpose, analytical and numerically efficient techniques for the synthesis of the aperture distribution and the correct evaluation of the radiating features (e.g., beamwidth, pointing angle, sidelobe levels, etc.) are presented in order to grant a real-time control of the digital beamforming network. A sub-array module demonstrator is fabricated and measured to corroborate the concept.

We define the notions of strong and strict recurrency for actions of countable ordered groups on $\sigma$-finite non atomic measure spaces with quasi-invariant measures. We show that strong recurrency is equivalent to non existence of weakly wandering sets of positive measure. We also show that for certain p.m.p ergodic actions the system is not strictly recurrent, which shows that strong and strict recurrency are not equivalent.

Это исследование сосредоточено на разработке системы искусственного зрения для гибкого дельта-робота-манипулятора и ее интеграции с межмашинной связью для оптимизации взаимодействия устройств в реальном времени. Эта интеграция направлена ​​на увеличение скорости роботизированной системы и улучшение ее общей производительности. Предлагаемое сочетание системы искусственного зрения с межмашинной связью позволяет обнаруживать и распознавать цели с высокой точностью в режиме реального времени в ограниченном пространстве, предназначенном для позиционирования, дальнейшей локализации и выполнения производственных процессов, таких как сборка или сортировка деталей. . В данном исследовании RGB-изображения используются в качестве входных данных для алгоритма MASK-R-CNN, а результаты обрабатываются в соответствии с особенностями прототипа дельта-манипулятора робота. Данные, полученные от MASK-R-CNN, адаптированы для использования в системе управления дельта-роботом с учетом ее уникальных характеристик и требований к позиционированию. Технология M2M позволяет манипулятору робота быстро реагировать на изменения, например, на перемещение объектов или изменение их положения, что имеет решающее значение для задач сортировки и упаковки. Система была протестирована в условиях, близких к реальным, чтобы оценить ее производительность и надежность.

The advancement of autonomous capabilities in maritime navigation has gained significant attention, with a trajectory moving from decision support systems to full autonomy. This push towards autonomy has led to extensive research focusing on collision avoidance, a critical aspect of safe navigation. Among the various possible approaches, Dynamic Programming is a promising tool for optimizing collision avoidance maneuvers. This paper presents a DP formulation for collision avoidance of autonomous vessels. We set up the problem framework, formulate it as a multi-stage decision process, define cost functions and constraints focusing on the actual requirements a marine maneuver must comply with, and propose a solution algorithm leveraging parallel computing. Additionally, we present a greedy approximation to reduce algorithm complexity. Through case studies, we demonstrate the effectiveness of the proposed approach in navigating complex scenarios, contributing to the future of autonomous maritime navigation. Through case studies, we show the efficacy of our approach in navigating complex scenarios.

Environmental estrogen pollution and estrogen effects on the female reproduction system are well-recognized scientifically. Among the estrogens, 17 β-estradiol is a priority in environmental estrogen pollution, and it is also a major contributor to estrogen which regulates the female reproduction system. 17 β-estradiol is carcinogen and has a tumor promotion effect relating to breast cancer, lung cancer and others. It also affects the psychological well-being such as depression, fatigue and others. Thus, a simple method of detection of 17 β-estradiol will be important for both environmental estrogen pollution and women’s health care. This study demonstrates a simple-use, cost effective 17 β-estradiol biosensor system which can be used for both environment and women’s health care applications. The bio-recognition mechanism is based on the influence of the redox couple, K₃Fe (CN) ₆/K₄Fe (CN) ₆ by the interaction between 17 β-estradiol antigen and its α-receptor (ER- α; α-estrogen antibody). The transduction mechanism is an electrochemical analytical technique, differential pulse voltammetry (DPV). The levels of 17 β-estradiol antigen studied was between 2.25 pg/mL to 2,250 pg/mL, Phosphate buffered saline (PBS), tap water from the Cleveland regional water district, and simulate urine were used as the test media covering the potential application areas for 17 β-estradiol detection. An interference study by testosterone which has a similar chemical structure and molecular weight as those of 17 β-estradiol was carried out, and this 17 β-estradiol biosensor showed excellent specificity without any interference by similar chemicals.

MIMO (multiple-input multiple-output) radar provides much more flexibility than the traditional radar for its ability to realize far more observation channels than the actual number of T/R (transmit and receive) elements. Designing the array of MIMO imaging radar, the commonly used virtual array theory generally assumes that all elements are placed on the same line. However, due to the physical size of the antennas and coupling effect between T/R elements, a certain height difference between T/R arrays is essential, resulting in the defocusing of edge points of the scene. On the other hand, the virtual array theory implies far-field approximation, leading to inevitable high grating lobes in the imaging result of near-field edge points of the scene observed by common MIMO array. To tackle these problems, this paper derives the relationship between target’s PSF (point spread function) and pattern of T/R arrays, by which the design criterion of near-field imaging MIMO array is presented. Firstly, the proper height between T/R arrays is designed to focus the near-field edge points well. Secondly, the far-field array is modified to suppress the grating lobes in the near-field area. Finally, the validity of the proposed methods is verified by simulations and an experiment.

Drowsiness is a main factor for various costly defects, even fatal accidents in areas such as construction, transportation, industry and medicine, due to the lack of monitoring vigilance in the mentioned areas. The implementation of a drowsiness detection system can greatly help to reduce the defects and accident rates by alerting individuals when they enter a drowsy state. This research proposes an Electroencephalography (EEG) based approach for detecting drowsiness. EEG signals are passed through a preprocessing chain composed of artifact removal and segmentation to ensure accurate detection followed by different feature extraction methods to extract the different features related to drowsiness. This work explores the use of various machine learning algorithms such as Support Vector Machine (SVM) the K Nearest Neighbor (KNN) the Naive Bayes (NB) the Decision Tree (DT) and the Multilayer Perceptron (MLP) to analyze EEG signals sourced from the DROZY database, carefully labeled into two distinct states of alertness (awake, and drowsy). Segmentation into 10-second intervals ensures precise detection, while a relevant feature selection layer enhances accuracy and generalizability. The proposed approach achieves high accuracy rates of 99.84% and 96.4% for intra (subject by subject) and inter (cross-subject) modes, respectively. SVM emerges as the most effective model for drowsiness detection in the intra mode, while MLP demonstrates superior accuracy in the inter mode. This research offers a promising avenue for implementing proactive drowsiness detection systems to enhance occupational safety across various industries.

Modern building automation systems implement plenty of advanced control and monitoring functions considering various parameters like users’ activity, lighting, temperature changes etc. Moreover, new solutions based on Internet of Things and cloud services are also being developed for smart buildings to ensure comfort of use, user safety, energy efficiency improvements and integration with smart grids and smart city platforms. Such a wide spectrum of technologies and functions requires a new approach in building automation systems design to provide effective way of their implementation and flexibility during operation. At the same time, in the building design and operation industries, tools based on building information modeling and digital twins are being developed. In this paper, the authors discuss development directions and application areas of these solutions, identifying new trends and possibilities of their use in smart homes and buildings. In particular, the focus is on procedures for selecting automation functions, effective integration, and interoperability of building management systems with Internet of Things considering organization of prediction mechanisms and dynamic functional changes in buildings and smart networks. Chosen solutions and functions should consider the requirements from EN ISO 52120 standard and the guidelines defined for the Smart Readiness Indicator.

: In this paper we present an optimization of the planar manufacturing scheme for stretch-free, shape induced metal interconnects to simplify the fabrication with the aim of maximizing the flexibility in the structure regarding to stress and strain. The Formation of trenches between silicon islands are actively used in the lithographic process to create arc shape structures by spin coating resist into the trenches. The resulting resist form is used as a template for the metal lines, which are structured on top. Because this arc shape is beneficial for the flexibility of these bridges. The trench depth as a key parameter for the stress distribution is investigated by applying numerical simulations. The simulated results show that the increase in penetration depth of the metal bridge into the trench increases the tensile load which is converted into a shear Force Q(x), that usually leads to increased strains the structure can generate. For the fabrication the filling of the trenches with resist is optimized by varying the spin speed. Compared to the theoretical resistance, the current-voltage measurements of the metal bridges show a similar behavior and almost every structural variation is capable of functioning as a flexible electrical interconnect in a complete island-bridge array.

Finding a good MIMO system model also major issue in Wireless Communication system. It is facing with so many problem, one of the major problem is finding good system model in terms of capacity and transmitting antenna system. In this paper, we analyze the channel capacity of various MIMO system model with some constant SNR level and outage probability. We establish a novel idea for MIMO system models as consider as 2^N- MIMO system model and find-out change in channel capacity when different transmitting antennas with constant SNR and outage probability. The channel capacity ratio CC_R is presented here on the basis of 2^N- MIMO channel capacity model. Number of transmitted antenna presented in MIMO system is increases is well-known however paper shows change in capacity in simple form.

The automotive market is very competitive and presents a demand for the consistent improvement of the used technologies and reduction of the product cost and dimensions with each product model iteration. Hence, it is important to have access to well-defined reference designs of high quality products, in order to evaluate the new ideas and technologies. This paper provides the readers with a numerical model of such a high quality product, i.e., the IPMSM type traction motor from the 4th generation of the Toyota Prius hybrid transaxle. In the introductory section, the brief history of the Prius model is given together with the references to the reverse engineering reports. Afterwards, the machine dimensions, material properties and winding configuration are described. Then, the model is validated with the torque measurements at constant speed. In the next chapters the simulation results are presented and the numerical source data are supplied to the reader. Finally, the design philosophy of the Toyota drive is briefly discussed in comparison with the BMWi3 drive and the results are concluded in the last section.

This paper presents a novel approach to designing beam codebooks for downlink multiuser hybrid multiple input multiple output (MIMO) wireless communication systems, leveraging multi-agent reinforcement learning (MARL). The primary objective is to develop an environment-specific beam codebook composed of non-interfering beams, learned by cooperative agents within the MARL framework. Machine learning (ML) based beam codebook design for downlink communications have been based on channel state information (CSI) feedback or only reference signal received power (RSRP) consisting of an offline training and user clustering phase. In massive MIMO, the full CSI feedback data is of large size and is resource-intensive to process, making it challenging to implement efficiently. RSRP alone for a stand-alone base station is not a good marker of the position of a receiver. Hence, in this work, uplink CSI estimated at the base station along with feedback of RSRP and binary acknowledgment of the accuracy of received data is utilized to design the beamforming codebook at the base station. Simulations using sub-array antenna and ray-tracing channel demonstrate the proposed system’s ability to learn topography-aware beam codebook for arbitrary beams serving multiple user groups simultaneously. The proposed method extends beyond mono-lobe and fixed beam architectures by dynamically adapting arbitrary shaped beams to avoid inter-beam interference, enhancing overall system performance. This work leverages MARL’s potential in creating efficient beam codebooks for hybrid MIMO systems, paving the way for enhanced multiuser communication in future wireless networks.

In the last decade, a higher level of reliability became a compulsory demand when it comes to modern DC-DC converters. This work addresses the main reliability metrics: the failure rate λλ and MTBF of an output capacitor bank used within a high current low voltage buck converter due to many studies have shown that the output capacitor bank was demonstrated being the most critical component within the converter. Many authors treated this issue, usually by doing reliability predictions. The majority of the papers use only one specific Standard Prediction to solve the problem. Herein calculation was done using both the older standard MIL-HDBK-217 and the latest one Telcordia SR-332, providing a benchmark comparison between the two which is a helpful tool for the output capacitor selection in the early stage design. Military standard was well accepted for decades in order to reliability prediction even on industrial electronics and is still used today under a critical manner because no more update after the latest version MIL-HDBK-217F - Notice 2 released in 1995. Since then, newer prediction standards had appeared in the electronics reliability market. Over time, this standard was mostly used but it does not accurately model the reliability because lack of taking account of mission profile. The above-mentioned newer standard – i.e., Telcordia SR-332 is trying to compensate also the lack of the newest component technology in the older standard (which is the first standard released on the market) supplying useful design data for design engineers who use the so-called “design with the reliability in mind” concept. Within the paper were established the environmental condition for the passive components by means of a PoL (Point of load) buck converter that is used for both calculation methods. The influence of temperature and several specific concepts like reference conditions, operating conditions, ripple, and internal self-heating were taking account in order to display the results. The temperature for the capacitor’s capsule needed in π_T stress factor calculation was derived by PSPICE simulation. High fidelity and dedicated SPICE models provided by the manufacturer were used for MOSFETs, polymer electrolytic, and MLCC capacitors that compose the converter.

Previous studies show that women with a history of high-grade CIN have a greater risk of subsequent high-grade anogenital intraepithelial neoplasia or cancer, and the risk is greater for vaginal cancer than for anal and vulvar cancers. It is hypothesized that the laparoscopic hysterectomy procedure may cause a higher incidence of VaIN in hysterectomized women. There are few studies addressing this issue and they show mixed results. This study aimed to investigate the incidence of high-grade or worse VaIN in the population of women undergoing hysterectomy for CIN3 or benign uterine disease, illustrate treatment options and follow-up. Methods: This retrospective study was conducted on 170 women who underwent laparoscopic hysterectomy for high-grade cervical intraepithelial neoplasia (CIN3) or benign gynecological disease. The follow-up strategy included performing a cotest and colposcopy with biopsy if necessary. The median time between primary treatment and diagnosis of high-grade VaIN was 18 months. Results: High grade or worse VaIN was found in 8 patients after hysterectomy (4.7%). All cases of high-grade VaIN occurred in women with persistent HPV infection. The most frequent genotype was 16. Women hysterectomized for CIN3 showed an 8-fold greater risk than women hysterectomized for benign disease of developing high-grade VaIN. The risk of VaIN is low in women hysterectomized for benign disease. The risk of developing VaIN is greater in women with viral persistence Conclusion. All these elements suggest that it is the history of HPV-related disease of the lower genital tract and viral persistence, rather than hysterectomy itself, that should be considered a risk factor for the development of high-grade VaIN. After hysterectomy, patients with a history of CIN should undergo annual screening with vaginal dome cytology and HPV testing.

Cryptococcus neoformans is a facultative intracellular fungal pathogen. Ten-generation-old (10GEN) C. neoformans cells are more resistant to phagocytosis and killing by macrophages than younger daughter cells. However, mechanisms that mediate this resistance and intracellular parasitism are poorly understood. Here, we identified factors important for the intracellular survival of 10GEN C. neoformans, such as urease activity, capsule synthesis, and DNA content using flow cytometry and fluorescent microscopy techniques. Real-time visualization of time-lapse imaging was applied to determine the phagosomal acidity, membrane permeability, and vomocytosis (non-lytic exocytosis) rate in J774 macrophages that phagocytosed C. neoformans of different generational ages. Our results showed that old C. neoformans exhibited higher urease activity, and enhanced capsule formation, which was supported by an increased Golgi complex. In addition, old C. neoformans were more likely to be arrested in the G2 phase, resulting in the occasional formation of aberrant trimera-like cells. To finish, the advanced generational age of the yeast cells slightly reduced vomocytosis events within host cells, which might be associated with increased phagolysosomal pH and membrane permeability. Altogether our results contribute to a better understanding of the strategies used by old C. neoformans to resist phagosomal killing and suggest that old generation C. neoformans intracellular behavior may be driving cryptococcosis pathogenesis.

In this paper, we present a new concept of the generalized core orthogonality (called the C-S orthogonality) for two generalized core invertible matrices $A$ and $B$. $A$ is said to be C-S orthogonal to $B$ if $A^{\tiny\textcircled{S}}B=0$ and $BA^{\tiny\textcircled{S}}=0$, where $A^{\tiny\textcircled{S}}$ is the generalized core inverse of $A$. The characterizations of C-S orthogonal matries and the C-S additivity are also provided. And the connection between the C-S orthogonality and C-S partial order has been given using their canonical form. Moreover, the concept of the strongly C-S orthogonality is defined and characterized.

As a derivative of graphene, graphene oxide (GO) was initially developed by chemists to emulate some of the key properties of graphene, but it was soon recognized as a unique material in its own right, addressing an application space that is not accessible to chemical vapor deposition based materials. Over the past decade, GO has emerged as a new frontier material with tremendous advances in its material fabrication and quality control over its properties. These in turn have led to rapid progress in GO based photonics, electronics, and optoelectronics concepts and devices, evoking new science and paving the way for many technological breakthroughs with exceptional performance. Here, we review the unique fundamental characteristics of GO, its thin film fabrication methods, patterning techniques, and mechanisms for tuning its material properties. This latter capability in particular has enabled novel advanced functional photonic, electronic, and optoelectronic devices. Understanding these insights is essential for designing and tailoring GO properties for state-of-the-art applications including solar energy harvesting, energy storage, medical diagnosis, image displays, and optical communications. We conclude by discussing the open challenges and exciting opportunities of this field, together with future prospects for major technological advancements and breakthroughs.

Photovoltaic (PV) systems, which are renewable energy sources, are increasingly being utilized in distributed generation. To maintain a stable energy balance, energy storage systems such as batteries (BAT) play a vital role. Electric vehicles (EVs) offer a promising solution with rechargeable battery systems for operation. The BATs must maintain their state of charge within design boundaries, despite intermittent PV and load power fluctuations, and advanced power control and management techniques are essential for their effective operation. The article evaluates an intelligent controller that uses a Sliding Mode Control adaptive deep learning algorithm Convolutional Neural Networks (SMC-CNN) and a unique Strategy for managing supervisory power. (SPMS) for photovoltaic systems with battery energy storage for better regulation of DC bus voltage. SMC-CNN offers exceptional resilience and seamless functionality, minimizing fluctuations in DC bus voltage in the control strategy design requirements. The primary goals are maintaining a consistent power supply and ensuring continuous service by preventing system components from exceeding capacity. This study aims to enhance the control of DC bus voltage in the PV and battery system, with the primary significance focusing on the following aspects. The advanced SPMS has been created, incorporating control system constraints to enhance SOC balancing speed and reduce fluctuations in DC bus voltage. Power flow management involves optimizing energy flow between the PV system, battery system, and load while minimizing battery capacity requirements. The proposed SMC-CNN and SPMS are demonstrated through real-time simulation using Matlab/Simulink, as demonstrated in comprehensive case studies.

Design process can be divided into stages of analysis and synthesis. This paper presents the application of the object-oriented technique to the synthesis as well as theoretical considerations concerning to design of gear size ranges. The synthesis consists in composition (aggregation) of single details into units – according to the rule: “from details up to general view”. The basics of the object-oriented synthesis were formulated. Furthermore, the consecutive stages of synthesis were formulated. The interactions between these stages were discussed. Some aspects were described in details e.g.: creation of interfaces for performance of the embodiment phase the designed artefact via CAD system drawing with specification (dimensions are still parametrically set). The final step of the procedure is creation of so called substantial (concrete) form of artifacts i.e. final assignment of dimensions which stored in the special data base. The final stage of the design process is issuing of technical documentation (technical drawings) created automatically via CAD system. The considerations are terminated by the list of advantages connected with the object-oriented approach to design (in comparison to the traditional way).

There are several challenges on how to attain energy efficiency while maintaining balance among factors affecting energy consumption such as power rating and temperature setpoints of cooling units, room temperature and humidity, and indoor air quality (IAQ). A real-time energy and IAQ monitoring system were installed in an educational building to profile the operational power consumption of inverter-based air condition unit (ACU) installed in each room. Polynomial curve and neural fitting regression analysis were applied to the real-time power consumption, indoor temperature and humidity, and carbon dioxide (CO2) level data. The derived models were able to provide the stabilizing indoor thermal and air conditions of the room to reach steady state ACU power consumption. These collected data and calculated parameters can be used to define rules in automating control of cooling appliances for an efficient energy utilization. The regression approaches, using real-time data, have determined the influence of indoor heat conditions and carbon dioxide levels on ACU power consumption. These parameters were utilized to establish consistent values for temperature, humidity, and carbon dioxide levels under stable settings of inverter-based air conditioning units.

A technique devised some years ago permits to study a theory in a regime of strong perturbations. This translate into a gradient expansion that, at the leading order, can recover the BKL solution. We solve exactly the leading order equations in a spherical symmetric case and we show that the 4-velocity in such a case is multiplied by an exponential warp factor when the perturbation is properly applied. This factor is always greater than one. We will give a closed form solution of this factor for a simple case. Some numerical examples are also given.

Digital solutions in the field of restorative neurology offer significant assistance, enabling patients to engage in rehabilitation activities remotely. This research introduces ReMoVES, an Internet of Medical Things (IoMT) system delivering telemedicine services specifically tailored for Multiple Sclerosis rehabilitation, within the overarching framework of the STORMS project. The ReMoVES platform facilitates the provision of a rehabilitative exercise protocol, seamlessly integrated into the Individual Rehabilitation Project, curated by a multidimensional medical team operating remotely. This manuscript delves into the second phase of the study, elucidating the technology employed, the outcomes achieved, and the practical, professional, and academic implications. The STORMS initiative, as the genesis of digital telerehabilitation solutions, aims to enhance the quality of life for Multiple Sclerosis patients.

The extensive utilization of drones has led to numerous scenarios that encompass both advantageous and perilous outcomes. By using deep learning techniques, it is aimed to reduce the dangerous effects of drone use through early detection of drones.The state of the art of the study is evaluation of deep learning approaches such as pre trained YOLOv8 drone detection for security issues. In this study, dataset collected by Mehdi Özel for a UAV competition are sourced from GitHub. These images are labeled using Roboflow, and the model is trained on Google Colab. To enhance model performance, dataset augmentation techniques including rotation and blurring are implemented. Following these steps, a significant precision value of 0.946, a notable recall value of 0.9605 and a considerable precision-recall curve value of 0.978 are achieved, surpassing many popular models such as Mask CNN, CNN, and YOLOv5.

The goal of the manuscript is to design a relatively best control structure for the noise suppression of a drone’s camera gimbal action. The gimbal’s movement can be simplified as a rest-to-rest reorientation system that can achieve the boundary result of a dynamic system. Six different control architectures are proposed and evaluated based on their ability to control the trajectory of the dynamic-system position and speed, their running time, and quadratic cost. The robustness of the control architecture to uncertainties in inertia and sensor noise is also analyzed. Monte Carlo figures are used to assess the performance of the six control systems. The conditions for applying different architectures are identified through this analysis. The analysis and experimental tests reveal the most suitable control of the drone’s camera gimbal rotation.

Leishmaniasis is the third most common vector-borne disease and a very important protozoan infection. Cutaneous leishmaniasis is one of the most common types of leishmaniasis infectious diseases with up to 2 million occurrences of new cases each year worldwide. A dynamic transmission multivariate time series model was applied to the data to account for overdispersion and evaluate the effects of three environmental layers as well as seasonality in the data. Furthermore, ecological niche modeling was used to investigate the geographical suitable conditions for cutaneous leishmaniasis using temperature, precipitation and altitude as environmental layers, together with the leishmaniasis presence data. A retrospective analysis of the cutaneous leishmaniasis spatial data in Afghanistan between 2003 and 2009 indicates a steady increase from 2003 to 2007, a small decrease in 2008, then another increase in 2009. An upward trend and regularly repeating patterns of highs and lows was observed related to the months of the year which suggests seasonality effect in the data. Two peaks were observed in the disease occurrence-- January to March and September to December -- which coincide with the cold period. Ecological niche modelling indicates that precipitation has the greatest contribution to the potential distribution of leishmaniasis.

Military medical service is an important component of the Armed Forces of any country [1]. In wartime, healthcare performs critical functions of medical support for military operations, providing effective and qualified care to the wounded and sick. Consequently, it is imperative to equip military hospitals with state-of-the-art materials and technical resources commensurate with the predefined requirements. In this study, we examine a series of enhancements applied to the TurtleBot 3 Waffle Pi-based medical assistant robot, tailored for deployment in military hospital settings.

The period of the COVID-19 pandemic resulted in a rapid development of innovative education methods, in particular using e-learning and remote work tools. The effects of this development are also post-pandemic changes in formal teaching regulations, in particular in higher education, allowing classes and lectures to be carried out with Blended Learning or Flipped Classroom methods. This paper provides information about a case study of implementing ICT technologies with elements of the mentioned methods in one of the subjects at a technical university. The implemented tools and solutions in the field of e-learning and interactivity are presented, along with information regarding their perception by students during two academic years in the post-COVID-19 period. The analysis of results of these information and student evaluations indicates their generally positive approach to such innovations in the educational path, and at the same time shows significant challenges for teachers to increase the attractiveness and effectiveness of the teaching process and the development of practical, technical skills of students.

We propose and experimentally realize a scheme of the optical nonreciprocity (ONR) using degenerate two-level atoms embedded in an optical ring cavity. For the degenerate transition Fg=4→Fe=3, we first study the cavity-transmission property in different coupling field, and verify that within the strong-coupling regime, the single-dark-state peak formed by electromagnetically induced transparency (EIT) shows ONR. Qualitative theoretical analysis shows that the stable ground-state Zeeman coherence is necessary for intracavity EIT. However, due to the frequency degeneracy, the large Rabi frequency of counter-propagating coupling field can reduce the number of effective atoms and weaken the strong-coupling of the atom-cavity, which determines that ONR based on intracavity EIT occurs only at weaker probe intensity. Furthermore, the ONR transmission with high contrast, linewidth-narrowed and broadband is experimentally demonstrated.

Abstract: Congenital hyperinsulinism (CHI) is a rare disorder of glucose metabolism and is the most common cause of severe and persistent hypoglycemia (hyperinsulinemic hypoglycemia, HH) in the neonatal period and childhood. Most cases are caused by mutations in the ABCC8 and KCNJ11 genes that encode the ATP-sensitive potassium channel (KATP). We present the correlation between genetic heterogeneity and the variable phenotype in patients with early-onset hyperinsulinemic hypoglycemia caused by ABCC8 gene mutations. In the first patients, which presented persistent severe hypoglycemia since the first day of life, molecular genetic testing revealed the presence of a homozygous mutation in the ABCC8 gene [deletion in the ABCC8 gene c.(2390+1_2391-1)_(3329+1_3330- 1)del] correlated with a diffuse form of hyperinsulinism (the parents being healthy heterozygous carriers). In the second patient, the onset was on the third day of life with severe hypoglycemia, and genetic testing identified a heterozygous mutation in the ABCC8 gene c.1792C>T (p.Arg598*) inherited on the paternal line, which led to the diagnosis of focal form of hyperinsulinism. To locate the focal lesions, (18)F-DOPA (3,4-dihydroxy-6-[18F]fluoro-L-phenylalanine) PET/CT was recommended (an investigation that cannot be carried out in the country), but the parents refused to carry out the investigation abroad. In this case, early surgical treatment could have been curative. In addition, the second child also presented secondary adrenal insufficiency requiring replacement therapy. At the same time, she developed early recurrent seizures that required antiepileptic treatment. We emphasize the importance and of molecular genetic testing for diagnosis, management and genetic counseling in patients with HH.

In the era of electrification and artificial intelligence, direct current motors are widely utilized with numerous innovative adaptive and learning methods. Traditional methods utilize model-based algebraic techniques with system identification, such as recursive least squares, extended least squares, and autoregressive moving averages. The new method known as deterministic artificial intelligence asserts physical-based process dynamics to achieve target trajectory tracking. There are two common autonomous trajectory generation algorithms: sinusoidal function and Pontryagin's based generation algorithm. This thesis aims to simulate model-following and deterministic artificial intelligence methods using sinusoidal and Pontryagin's methods and compare their performance difference when following challenging step function slew maneuver.

The human landscape transforming activity contributes to the global change of vegetation in different forms. Hunting is one of the most ancient human landscape-shaping activities. Feeders for hunting are particularly disruptive to vegetation. In the present study, we conducted a vegetation survey in these highly disturbed places. We are investigating the vegetation dynamics over several years in in the turkey oak–sessile oak zone, in two areas with different moisture and shade conditions (forest and clearing). One important background factor is changes in precipitation and temperature. The novelty of our present study lies in the fact that the observation takes place with continuous disturbance, where the human influence is very large. Our results confirm that the weed infestation be detectable at bait sites over a long period, and the interannual changes were typical in every year, according to the fact that in August, more weed species are usually present with a greater cover at the bait sites. The main meteorological factors played a role in the degree of weed infestation in each year. There was a higher proportion of vegetation regeneration in wetter years, while dry periods do not favor successional processes. With the drying of the climate, the disturbed areas are constantly losing their natural value, but wetter weather is not an automatic solution either. A more precise understanding of vulnerable systems and careful planning of treatment interventions is necessary.

This study investigates the impact of vertical greenery systems (VGS) applied to heavyweight walls on indoor thermal conditions in a building module situated in the Mediterranean climate of Catania, Italy. Using dynamic simulations in TRNSYS, the research compares the thermal behavior of walls constructed from hollow clay blocks (Poroton) and lava stone blocks with a lightweight wall setup already in place at the University of Catania. The primary focus is on evaluating the VGS’s effect on reducing peak inner surface temperatures and moderating heat flux fluctuations entering the building. The findings indicate that adding a vertical greenery layer to heavyweight walls can decrease the peak inner surface temperature by up to 1.0°C compared to the same wall without vegetation. However, the greenery’s impact on mitigating heat flux fluctuations is less pronounced than in the case of the lightweight wall. This research underscores the potential of green facades in enhancing indoor thermal comfort in regions with climates similar to the Mediterranean, providing valuable insights for sustainable building design and urban planning.

The growing attention for plug-in electric vehicles, and the associated high-performance demands, have initiated a development trend towards highly efficient and compact on-board battery chargers. These isolated ac-dc converters are most commonly realized using two conversion stages, combining a non-isolated power factor correction (PFC) rectifier with an isolated dc-dc converter. This, however, involves two loss stages and a relatively high component count, limiting the achievable efficiency and power density and resulting in high costs. In this paper a single-stage converter approach is analyzed to realize a single-phase ac-dc converter, combining all functionalities into one conversion stage and thus enabling a cost-effective efficiency and power density increase. The converter topology consists of a quasi-lossless synchronous rectifier followed by an isolated dual active bridge (DAB) dc-dc converter, putting a small filter capacitor in between. To show the performance potential of this bidirectional, isolated ac-dc converter, a comprehensive design procedure and multi-objective optimization with respect to efficiency and power density is presented, using detailed loss and volume models. The models and procedures are verified by a 3.7 kW hardware demonstrator, interfacing a 400 V dc-bus with the single-phase 230 V, 50 Hz utility grid. Measurement results indicate a state-of-the-art efficiency of 96.1% and power density of 2.2 kW/dm³, confirming the competitiveness of the investigated single-stage DAB ac-dc converter.

Industrial pilot projects often rely on proprietary and expensive electronic hardware to control and monitor experiments. This raises costs and retards innovation. Open-source hardware tools exist for implementing these processes individually, however, they are not easily integrated with other designs. The Broadly Reconfigurable and Expandable Automation Device (BREAD) framework provides many open-source devices which can be connected to create more complex data acquisition and control systems. This article explores the feasibility of using BREAD plug-and-play open hardware to quickly design and test monitoring and control electronics for an industrial materials processing prototype pyrolysis reactor. Generally, pilot-scale pyrolysis plants are expensive custom designed systems. The plug-and-play prototype approach is first tested by connecting it to the pyrolysis reactor and ensuring it can measure temperature and actuate heaters and a stirring motor. Next, a single circuit board system was created and tested using the designs from the BREAD prototype to reduce the number of microcontrollers required. Both open-source control systems were capable of reliably running the pyrolysis reactor continuously and the overall cost of control was reduced by more than 10X. Open-source, plug-and-play hardware provides a reliable avenue for researchers to quickly develop data acquisition and control electronics for industrial-scale experiments.

The ubiquitous diffusion of Power Electronic Converters (PECs) in many fields of application including traction and energy conversion is suggesting the possibility of new and better integration of advanced power conversion and ICT services. This work investigates the possible advancements in the use of optical fibers for control of PECs, using Plastic Optical Fiber. The optical communication link connects the switching control to the converter control, following the line of separation between the expertises of the power electronic engineer and the control engineer. Control wise, the PEC becomes a black box compatible with any off-board controller, now immune from the Electromagnetic Interference (EMI) produced by the power switches. The redundant optical link is ready for the high switching (and sampling) frequencies possible with the use of SiC power semiconductor devices (100 kHz+). Distributed control of multiple PEC units and advanced telemetry for diagnostics and prognostics are targeted. A proof-of-concept demonstrator is presented and tested. Moreover, the possible evolution towards a power electronic cloud with remote management and orchestration is described.

Tungsten balls with sub-100-μm diameter can function as probe tips for micro-coordinate measuring machines (CMMs) to measure ultraprecise workpieces such as ceramic bearings with a high aspect ratio. A high-precision measuring system was proposed to evaluate the roundness error of the self-made tungsten ball tips. The principles and mathematical models of the measuring system are illustrated, and the fabrication principle of tungsten balls is introduced. An analysis was conducted on the maximum allowable contact force and bending strength of the tungsten ball tips, and the elastic mechanism was designed based on the analysis. A ruby probe with a sphericity error of 130 nm (A-5003-0577, Renishaw Corporation) used as a reference sphere was measured to verify the system's effectiveness. Repeated measurement experiments were performed for two tungsten ball tips. The results show the roundness error of the tungsten ball-A is between 568.3 and 586.2 nm with a standard deviation of 6.6 nm while the tungsten ball-B’s roundness error is between 898.5 and 958.0 nm with a standard deviation of 19.7 nm. The uncertainty is calculated as 125.8 nm. The developed system can stably measure the roundness of the tungsten ball tips.

This study provides a comprehensive analysis of global patent trends in battery recycling, focusing on secondary batteries and related technologies across Korea, China, and the United States. The data, collected from various patent databases, was quantitatively analyzed to identify technology trends and direct future development. The analysis reveals distinct emphases on technologies such as lithium-ion and waste battery recycling, highlighting notable differences in patent activities among key companies and countries. China's large number of patents in battery manufacturing processes contrasts with the USA's focus on electrochemical cell construction and storage systems, while Korea shows significant activity in waste battery technology. The study underscores the competitive landscape and innovation efforts in the battery recycling sector, providing insights into the technological focuses and priorities of each country. It also identifies key challenges, such as the need for consistent innovation and broader geographic coverage in Korea, enhancing patent influence and international presence in China, and ensuring high patent quality and fostering innovation in lagging sectors in the United States. Addressing these challenges through enhanced collaboration, increased R&D investments, and supportive policies is crucial for strengthening the global position and driving further innovation in the battery recycling sector.

Background: Periodontitis is a disease that leads to serious functional and aesthetic dysfunctions resulting in impairment of life quality; it exists in different forms and its etiology is related with multiple component causes. Angiogenesis, together with inflammatory infiltrate, are two key processes in the evolution of inflammatory processes involving gingival tissues. The aim of this study was to evaluate their alterations in relation to some important periodontal diseases-associated factors (i.e. smoke, sex, age, plaque, pus, probing pocket depth) in patients with diagnosis of Generalized Aggressive Periodontitis (GAP). Methods: Eighteen subjects with GAP were enrolled for this study. Percentage of inflammatory cells and vascular area were measured and evaluated in relation with each periodontal diseases-associated factor. Results: The results showed a significant decrease of the percentage of vascular area in association with almost all the periodontal diseases-related factors (smoke, age, PPD, plaque) and not significant differences in the percentage of inflammatory cells. Conclusions: Data suggest that, even if these factors are often commonly related to worsening of periodontal status, they did not affect inflammatory and vascular pattern, as we can assume. For the future, additional studies, aimed to evaluated each singular factor in a wider sample size, should be planned.

Few prior works study self-driving cars by deep learning with IoT collaboration. SDC-Net, which is an end-to-end multitask self-driving car camera cocoon IoT-based system, is one of the research that tackles this direction. However, by design SDC-Net is not able to identify the accident locations, it only classifies if it is a crash scene or not. In this work, we introduce an enhanced design for the SDC-Net system by 1) replacing the classification network with a detection one, 2) adapting our benchmark dataset labels built on the CARLA simulator to include the vehicles bounding boxes while keeping the same training, validation, and testing samples, 3) modifying the shared information via IoT to include the accident location. We keep the same path planning and automatic emergency braking network, the digital automation platform, and the input representations to formulate the comparative study. SDC-Net++ system is proposed to 1) output the relevant control actions, especially in case of accidents: accelerate, decelerate, maneuver, and brake, and 2) share the most critical information to the connected vehicles via IoT, especially the accident locations. A comparative study is also conducted between SDC-Net and SDC-Net++ with the same input representations: front camera only, panorama and bird-eye views, and with single-task networks: crash avoidance only, and multitask networks. Multitask network with a BEV input representation outperforms the nearest representation in precision, recall, f1-score, and accuracy by more than 15.134%, 12.046%, 13.593%, and 5%, respectively. SDC-Net++ multitask network with BEV outperforms SDC-Net multitask with BEV in precision, recall, f1-score, accuracy, and average MSE by more than 2.201%, 2.8%, 2.505%, 2%, and 18.677% respectively.

Sustainable supply chain management (SSCM) represents a critical strategy for the electronics industry to balance economic objectives with environmental and social responsibility across complex global production networks. This multiple case study analysis investigates SSCM integration within leading Korean electronics manufacturers Samsung, LG, and Hyundai. In-depth qualitative data, focus groups, and sustainability report analysis reveals the policies, practices, results and implementation barriers related to incorporating sustainability criteria across procurement, manufacturing, distribution and recycling functions. Findings show sustainability considerations increasingly driven by cost, risk, reputational and regulatory factors, with vertical coordination initiatives helping transfer knowledge to assist suppliers on compliance and emissions reductions. Yet substantial obstacles persist around monitoring, coordination, transparency and technical capabilities, especially amongst lower tiers. The paper discusses how common reporting standards, ethical sourcing certification and partnerships can accelerate electronics supply chain sustainability. By mapping integration achievements and gaps, this study informs managerial best practices and policy reforms toward promoting socially and ecologically responsible models for Korea's vital export industry as it navigates rising stakeholder pressures.

In recent times, the application areas of unmanned aerial vehicles (UAVs) are expanding, and autonomous functions are becoming increasingly prominent, eliminating the need for remote pilot control. Certain applications require the drone to use a docking station autonomously, even for wireless charging. This involves performing autonomous takeoff and landing, where high preci-sion is demanded. These maneuvers can be significantly influenced by environmental factors. The effectiveness of the precision landing function of the DJI Mavic 2 Pro UAV in strong winds is in-vestigated in this article based on experimental measurements conducted outdoors. New findings on the precision landing capabilities of the DJI Mavic 2 Pro UAV are presented in this paper, par-ticularly under windy conditions. The efficiency of precision landing is compared in cases when the precision landing function is enabled versus when it is disabled. It is investigated whether there is a statistically significant difference between the two landing modes in strong winds and it is examined whether the DJI Mavic 2 Pro can perform precision landing on a surface of a specific size in windy conditions. This helps to predict the suitability of the DJI Mavic 2 Pro for precise landing and wireless charging at a docking station in strong winds and high gusts.

Predicting type 2 diabetes mellitus (T2DM) using phenotypic data with machine learning (ML) techniques has received significant attention in recent years. PyCaret, an ML tool that enables the simultaneous application of 16 different algorithms, was used to predict T2DM using phenotypic variables from the “Nurses’ Health Study” and “Health Professionals’ Follow-up Study” datasets. Ridge classifier, Linear Discriminant Analysis, and Logistic Regression (LR) were the best-performing models for the male-only data subset. For the female-only data subset, LR, Gra-dient Boosting Classifier, and CatBoost Classifier were the strongest models. The AUC, accuracy, and precision were 0.77, 0.70, and 0.70 for males and 0.79, 0.70, and 0.71 for females, respective-ly. The feature importance plot showed that familial history of diabetes (famdb), never having smoked, and high blood pressure (hbp) were the most influential features in females, while famdb, hbp, and current smoking were the major variables in males. In conclusion, PyCaret was used successfully for speed analysis for the prediction of T2DM by simplifying complex ML tasks. Gen-der differences are an important consideration for T2DM prediction. Despite this comprehensive ML tool, phenotypic variables alone may not be sufficient for early T2DM prediction; genotypic variables could also be used in combination for future studies.

We introduce a novel stochastically correlated two-factor (i.e., bivariate) diffusion process under the square-root format, for which we obtained, analytically, the corresponding solutions for the conditional moment generating functions and conditional characteristic functions. Such solutions recover verbatim those of the uncorrelated case. We believe that the The aforementioned model encompasses a range of processes similar to that produced by a bivariate square-root process in which entries are correlated in the standard way, i.e., via a constant correlation coefficient. Note that, for the latter, closed-form solutions for the conditional characteristic functions are not available. We focus on the financial scenario of obtaining closed-form expressions for the exact price of a zero-coupon bond and Asian option prices via a Fourier cosine series method.

The nucleation and dynamics of Josephson and Abrikosov vortices determine the critical currents of layered high-T_c superconducting (HTS) thin films, grain boundaries, and coated conductors, so understanding their mechanisms is of crucial importance. Here we treat pair creation of Josephson and Abrikosov vortices in layered superconductors as a secondary Josephson effect, in which each full vortex is viewed as a composite fluid of micro-vortices, such as pancake vortices, which tunnel coherently via a tunneling matrix element. We introduce a two-terminal magnetic (Weber) blockade effect that blocks tunneling below a threshold current, and simulate time-correlated vortex tunneling above threshold. The model shows nearly precise agreement with voltage-current (V-I) characteristics of HTS cuprate grain boundary junctions, which becomes more concave rounded as temperature decreases, and also explains the piecewise linear V-I behavior observed in iron-pnictide bicrystal junctions and other HTS devices. When applied to either Abrikosov or Josephson pair creation, the model explains a plateau seen in plots of critical current vs. thickness of HTS coated conductors. The observed correlation between theory and experiment strongly supports the proposed quantum picture of vortex nucleation and dynamics in layered superconductors.

The need for integrated high-frequency systems has increased significantly, leading to the development of efficient antennas operating in the 0.1-10 terahertz (THz) range. Using graphene as the conducting 2D material and hexagonal boron nitride (hBN) as the dielectric substrate, this research effort examines the design and performance evaluation of a THz band antenna functioning on supporting nanotechnology. The researchers contrasted the system’s performance with the 6G wireless network requirements after analyzing the antenna performance, radiation patterns, and impedance matching. According to this research, graphene, along with hBN can enhance antenna performance overall in the THz band and open pathways for advanced communication. The application of the designed antenna in a 6G wireless network will be tested through um MIMO configuration to achieve a higher data rate.

he paper offers an innovative cooking utensil design for remote, isolated, and even peri-urban communities at a low price, with high reliability and simple construction. It can alleviate energy poverty and improve food security. This utensil uses only local solar energy directly and allows comfortable indoor cooking. This paper provides the design principles of a solar cooker/frying pan or generic heater, based on a PV panel or a plurality of them, which are directly connected to a plurality of Positive Thermal Coefficient (PTC) resistors to match the power. PTCs are nowadays produced in massive quantities and are widely available at low cost. The proposed device does not require an electronic controller or a battery for its operation. The aim is for family use, although the design can be easily scaled to a larger size or power, maintaining its simplicity. Electric heating inside or attached to the cooking pot, plus the temperature self-limiting effect of PTCs, allows for thermally insulating the cooking pot from its outside using ordinary materials. Insulation en-hances energy efficiency during cooking and keeps cooked food warm for a long time. Clean development would receive a significant impulse with its application. A simple mathematical model describes its functioning and states guidelines for adequate design. The results indicate a successful proof of concept and high efficiency both for water and oil as representatives of cooking.

Motivated by South Africa's need in the transition to a net-zero economy; this study 10 investigates the integration of renewable energy sources (RES) into oil refineries, considering 11 therein unique challenges and opportunities. The research focuses on optimizing RES allocation 12 using Particle Swarm Optimization (PSO), a data-driven approach that adapts to real-time 13 operational conditions. Traditional energy management systems often struggle with the inherent 14variability of RES, leading to suboptimal energy distribution and increased emissions. Therefore, 15 this study proposes a PSO-based renewable energy allocation strategy specifically designed for oil 16 refineries. It considers factors like the levelized cost of energy, geographical location, and available 17 technology. The methodology involves formulating the optimization problem, developing a PSO 18 model, and implementing it in a simulated oil refinery environment. The results demonstrate 19 significant convergence of the PSO algorithm, leading to an optimal configuration for integrating 20 RES and achieving cost reductions and sustainability goals. The optimization result of 4,457,527.00 21 Rand achieved by iterations is much better than the result of 4,829,638.88 Rand acquired using 22Linear Programming as the baseline model. The mean cost, indicating consistent performance, has 23 remained at its original value of 4,457,527.00 Rand, highlighting the convergence. Key findings 24 include the average distance measure decreasing from 4.2 to 3.4, indicating particle convergence; 25 swarm diameter decreasing from 4.7 to 3.8, showing swarm concentration on promising solutions; 26 average velocity decreasing from 7.8 to 4.25, demonstrating refined particle movement; and the 27 optimum cost function achieved at 4,457,527 Rand with zero standard deviation, highlighting 28 stability and optimal solution identification. This research offers a valuable solution for oil 29 refineries seeking to integrate RES effectively, contributing to South Africa's transition to a 30sustainable energy future.

The persistence of symptoms following COVID-19 infection represents a significant challenge in healthcare management. During the outbreak, tele-rehabilitation emerged as a new tool to support healthcare structures in providing rehabilitation services. This study assessed the effectiveness and the feasibility of a 3-week home-based motor and respiratory rehabilitation program for long COVID-19 individuals after traditional rehabilitation. Twenty-three patients completed the program and underwent functional tests at different time points (i.e. baseline, after hospital discharge, and after tele-rehabilitation). Motor function was evaluated using the instrumented Six-Minutes Walking Test (i6MWT), with monitored heart rate and oxygen saturation. Conversely, respiratory function was measured via forced vital capacity (FVC) and maximal voluntary ventilation (MVV) tests. Significant improvements (p < 0.05) in motor and respiratory function were observed throughout the intervention, including an 18.3% increase in walked distance from the baseline. The findings suggest that a home-based tele-rehabilitation can enhance motor and respiratory function in post-COVID patients. Despite limitations such as sample size and lack of control group, the positive outcomes seem to support the feasibility of the proposed tele-rehabilitation program in managing long COVID symptoms and promoting functional recovery. Further research is needed to validate these findings and explore tele-rehabilitation’s potential in broader patient populations.

In addressing the multifaceted problem of multiple-input multiple-output (MIMO) detection in wireless communication systems, this work highlights the pressing need for enhanced detection reliability under variable channel conditions and MIMO antenna configurations. We propose a novel method that sets a new standard for deep unfolding approaches to MIMO detection by integrating the iterative conjugate gradient method with Tikhonov regularization, combining the adaptability of modern deep learning techniques with the robustness of classical regularization. Unlike conventional techniques, our strategy treats the regularization parameter of Tikhonov regularization as well as step size values and search direction coefficients of conjugate gradient (CG) method as trainable parameters within the deep learning framework, allowing for dynamic modification according to channel conditions and MIMO antenna configurations. Detection performance is significantly improved by the proposed approach in variety of conditions. In different MIMO settings, the suggested method consistently shows better bit error rate (BER) and normalized minimum mean square error (NMSE) performance. Across a range of MIMO configurations and channel conditions, the proposed method exhibits significantly lower BER and NMSE values than well-known techniques such as DetNet and CG. The proposed method has superior performance over CG and other model-oriented methods, especially in small number of iterations. Consequently, the simulation results demonstrate the flexibility of the proposed approach, making it a viable choice for MIMO systems with a range of antenna configurations and different channnel conditions.

A configurable design of a microstrip square spiral RFID tag antenna, for a wide range of microwave frequencies in S- and C-band, is presented. The design is parameterized in dimensions, and hence changing the design frequency (or frequencies) is easy, by changing only an initial value for the spiral geometry. A tag specimen was fabricated using Cu electroplating technique according to the design for frequencies of interest in the areas of 2.4 and 5.8 GHz. The substrate material is a 320 μm high resistivity Si and the bridge dielectric is a 15μm polyimide PI2525. The microfabrication process involves steps of metallic structure pattern transfer techniques with optical UV lithography procedures. The reflection coefficient and gain of the specimen were measured inside an anechoic enclosure using a vector network analyzer (VNA) and a TEM horn test antenna over a frequency range of up to 6 GHz. Simulated and measured results are presented and discussed, exhibiting reasonable agreement.

Wind energy is a kind of renewable energy with great potential for development. This study mainly investigated the application of shock waves generated by high-pressure gases (wind energy) for generating energy. In this study, we designed a new supersonic shock wave generator that can be reused without disassembling and assembling bolts and developed a supersonic shock wave monitoring system. This system monitored the velocity of the generated shock waves, which was Mach 3-5, and the output pressure was more than 100 times higher than the input pressure of the shock wave generator tank.Then, we developed a power generation system driven by supersonic shock waves based on the characteristics of the new shock wave generator, which can generate high-pressure and high-speed blast waves and can be reused. The shock wave generator can repeatedly generate high-pressure waves to drive the Tesla turbine and then the magnetic energy generator for power generation. We established a complete control process for power generation driven by shock waves by controlling the valve stem. The system can detect the tank pressure, output pressure, gas flow, rotation speed, voltage, and current during the control process for the performance analysis of power generation.

Despite being stored at 113 K and atmospheric pressure, LNG cold potential is not exploited to reduce green ships’ energy needs. An innovative system based on three Organic Ranking Cycles integrated into the regasification equipment is proposed to produce additional power and recover cooling energy from condensers. A first-law analysis identified ethylene and ethane as suitable working fluids for the first and the second ORC making available freshwater and ice. Propane, ammonia and propylene could be arbitrarily employed in the third ORC for air-conditioning. An environmental analysis that combines exergy efficiency, ecological indices and hazard aspects for marine environment and ship’s passengers, indicated propylene as safer and more environmentally friendly. The exergy analysis confirms more than 20% of the LNG potential can be recovered from every cycle to produce a net clean power of 76 kW, whereas 270 kW can be saved by recovering condensers' cooling power to satisfy some ship needs. Assuming the sailing mode, a limitation of 162 kg in LNG consumptions was determined, avoiding the emission of 1584 kg of CO2 per day. Marine thermal pollution is reduced by 3.5 times by recovering the working fluids' condensation heat for the LNG pre-heating.