The document provides an overview of a presentation on sensors and actuators for a robotics club. It discusses:
1. The comparison between transducers, sensors, and actuators.
2. Descriptions and classifications of different sensor types including active vs passive sensors.
3. How actuators work and examples like motors.
4. The computer process control system and concepts like analog to digital conversion, sampling, quantization, and encoding.
Report
Share
Report
Share
1 of 37
Download to read offline
More Related Content
Sensors-and-Actuators-working principle and types of sensors
1. SENSORS & ACTUATORS
Robotics Club
(Science and Technology Council, IITK)
PRESENTED BY
HUMANOID IIT KANPUR
October 11th
, 2017
2. WHAT ARE WE GOING TO LEARN !!
● COMPARISON between Transducers Sensors And Actuators.
● Brief description About Sensors, Types of Sensors, Classifications .
● Actuators and it’s working.
● COMPUTER PROCESS CONTROL SYSTEM.
● Analog To Digital Convertor.
● Sampling ,Quantization, Encoding.
7. Classification of Sensors
Source:
http://wtlab.iis.u-tokyo.ac.jp/~wataru/lecture/rsgis/rsnote/cp2/cp2-1.htm
In passive sensing, sensor measures the energy that is naturally available, such as thermal
infrared, surface emissions.
In active sensing, sensors provides energy on their own as a source of illumination. The energy
reflected by the target is detected and measured.
Note: The above two terms are used with the perspective of remote sensing.
9. What makes a good sensor?
• Precision: An ideal sensor produces same output for
same input. It is affected by noise and hysteresis.
• Resolution: The ability to detect small changes in the
measuring parameter
• Accuracy: ‘It is the combination of precision,
resolution and calibration.’
Source: https://learn.adafruit.com/calibrating-sensors/why-calibrate
10. Calibration of Sensors
Most sensors are not ideal and are often affected by surrounding noise. For a
color sensor, this could be ambient light, and specular distributions.
If a sensor is known to be accurate, it can be used to make comparison with reference
readings. This is usually done with respect to certain standard physical references, such
as for a rangefinder we may use a ruler for calibration.
Each sensor has a ‘characteristic curve’ that defines the sensor’s response to an input.
The calibration process maps the sensor’s response to an ideal linear response
11. Characteristic Curve of Sensor
Suppose the output of a sensor for some physical quantity x(t) is given by f(x(t)):
• Linear Model
, where
• Affine Model
, where ,
Often, ‘a’ is called the proportionality constant, which gives an idea of the
sensitivity of the sensor, and ‘b’ denotes the bias.
Note: The sensitivity of a sensor is ratio of output value to measured quantity.
12. Sensor’s Operating Range
If the operating range of a sensor is (L, H),
To get an idea of how precise the measurements of a sensor can be, one defines its
precision ‘p’ as the smallest difference between two distinguishable sensor readings
of the physical quantity.
13. Sampling and Quantisation
Continuous-time
continuous amplitude
input signal
Discrete-time
continuous amplitude
signal (PAM)
Discrete-time
discrete amplitude
signal (PCM)
Digital bit stream
output signal
The process of the discretization of the domain of the signal being measured is
called sampling, whereas quantization refers to the discretisation of the range.
Pulse Code Modulator
14. Sampling and Quantisation
SAMPLING: Evaluating the input signal at discrete
units of time, say 0, T, 2T, ….. nT.
QUANTIZING: Provides discretized values to the
input on basis of a finite number of thresholding
conditions
ENCODING: Transforms the digital data into a
digital signal, comprising of bits 0111011…, on basis
of various schemes.
Manchester Line code
15. Sampling and Quantisation
• If the sampling rate isn’t high, one can end up with different signals(aliases) during
reconstruction, that fit the same set of sample points. This is called aliasing, and is
undesirable. For best sampling, the sampling rate must be >= 2 times the frequency of
the signal. (Nyquist Shannon Sampling Theorem)
• In the case of quantisation, selection of fewer levels of discretisation can lead to
progressive loss of spatial detail. Also, contours(artificial boundaries) can start
appearing due to sudden changes in intensity. For audio signals, this can be heard as
noise/distortions.
16. VARIETIES OF SENSORS
Acoustic Sensors
Geophone
Hydrophone
Microphone
Automotive Sensors
Air flow meter
Speedometer
Hall-Effect Sensor
Air- Fuel Ratio meter
Electric Current Sensors
Hall Probe
Magnetometer
Current sensor
Voltage Detector
Navigation Instruments
LIDAR
Gyroscope Rotary
Encoder Odometer
Tachometer
Optical Sensor
Photodiode
Infrared sensor
Camera
Proximity Sensor
Infrared sensor
Ultrasonic sensor
17. 1. Camera
Vision processing requires a lot of RAM, and even low resolution cameras may
give lots of data, parsing through which can be difficult.
Cameras draw in around 0.1 A current, the current rating of the USB hub to which they
are attached must be checked.
Raspberry Pi
Camera
Advamotion
18. 2. Inertial Measurement Unit
• Consists of three sensors:
o Accelerometer: Used to measure inertial
acceleration
o Gyroscope :Measures angular velocity
about defined axis
o Magnetometer : Can be used along with
gyroscope to get better estimates of robot’s
orientation (i.e. roll, pitch, yaw)
19. 3. Photo-resistors
Light sensitive resistors whose resistance decreases
as the intensity of light they are exposed to
increases. They are made of high resistance
semiconductor material.
When light hits the device, the photons give
electrons energy. This makes them jump into the
conductive band and thereby conduct electricity.
20. 4. Infrared Sensor
● IR led is led that emits light in IR region and can't be
seen by the eyes.
● Photodiode is a type of diode which works in
reverse bias and its resistance is changed when
subjected to change in light intensity.
● They are used for colour detection etc.
21. 5. Flex Sensors
Measure the amount of deflection caused by
bending, also called bend sensors.
The bending must occur around a radius of
curvature, as by some angle at a point isn’t
effective and if done by more than 90 deg.,
may permanently damage the sensor.
22. 6. Ultrasonic Sensor
These are commonly used for obstacle detection.
Works on principle similar to that of Sonar which
consists of time of flight,the Doppler effect and the
attenuation of sound waves.
23. 7. Rotary Encoder
They convert the angular position of a
shaft or axle to a
analog / digital code.
They may represent the value in
absolute or incremental terms. The
advantage of absolute encoders is that
they maintain the information of the
position even when power is removed,
and this is available immediately on its
application.
24. 8. Touch Sensor
Touch sensors can be defined as
switches that are activated by the
touch.
Examples includes capacitance
touch switch, resistance touch
switch, and piezo touch switch.
25. 9.Thermocouple
● Converts thermal energy into
electrical energy and is used to
measure temperature.
● When two dissimilar metal wires
are connected at one end
forming a junction, and that
junction is heated, a voltage is
generated across the junction .
27. In a robot, actuators are used in order to produce some mechanical movement.
TYPES OF ACTUATORS
Electric
Electro-mechanical devices
which allow movement
through use of electrically
controlled systems of gears
DC Motor
Hydraulic
Transforms energy stored
in reservoirs into
mechanical energy by
means of suitable pumps
Water Pump by
Tefulong Ltd.
Pneumatic
Uses pneumatic energy provided
by air compressor and transforms it
into mechanical energy by means
of pistons or turbines
Pneumatic cylinder
by Janatics Ltd.
29. MOTOR DRIVER
• Microcontrollers, typically, have current rating of 5-10 mA, while motors draw a supply
of 150mA. This means motors can’t be directly connected to microcontroller.
• For electromechanical actuators, following motor drivers are often used:
o Simple DC Motors: L298, L293
o Servo Motors: Already have power cable and different control cable
o Stepper Motors: L/R Driver Circuit, Chopper Drive
L298N Stepper Motor Driver Controller
30. L298 DUAL H-BRIDGE IC
• Allowsto independentlycontrol
two DC motors up to 2 A each in
both directions.
• Power consumption for logical part
0-36 mA
• Requires protective diodes against
back e.m.f. externally
Connections to L298 Dual H-Bridge 2A
31. H- BRIDGE
It is an electronic circuit used to apply voltage across a load in either direction
on basis of input from a microcontroller
S1 S2 S3 S4 Result
1 0 0 1 Motor moves right
0 1 1 0 Motor moves left
0 0 0 0 Motor coasts
0 1 0 1 Motor brakes
1 0 1 0 Motor brakes
1 1 0 0 Short circuit
0 0 1 1 Short circuit
1 1 1 1 Short circuit
32. SPEED CONTROL USING PWM
● Pulse Width Modulation
(PWM) is scheme in which
duty cycle of square wave
output fromthe
microcontroller is varied by
providing a varying average
DC output
● Voltage seen by the load is
directly proportional to the
unregulated source voltage
34. Components of a System Hardware
Plant
(Physical World)
Controller
(Digital World)
Sensors
Actuators
Input Signal
To plant
Output Signal
From plant
Measured
Plant Output
Control
Effort
35. Data Handling Systems
Both data about the physical world and control signals sent to interact with
the physical world are typically "analog" or continuously varying quantities.
In order to use the power of digital electronics, one must convert from
analog to digital form on the experimental measurement end and convert
from digital to analog form on the control or output end of a laboratory
system.
36. Data Collection after Control
Source: http://hyperphysics.phy-astr.gsu.edu/hbase/hph.html