A comprehensive Energy Audit of a Maintenance facility was performed to assess its energy performance and identify scope for improvement. The facility’s Energy Use Intensity (EUI) for 2022 was 404 kWh/m2 — more than double the Benchmark EUI for Maintenance facilities (151 kWh/m2) recommended by EnergyStar. Furthermore, the Load Factor for 2022 was 0.22, which is lower than the recommended minimum of 0.75 for an efficient building. The audit encompassed an in-depth evaluation of the building's structural and operational characteristics, comprising HVAC systems, lighting, building envelope, and energy-intensive machinery. An energy model of the building was developed to emulate the baseline building energy performance for 2022. Following the energy model's development and validation, an analysis was conducted to identify energy-intensive areas and opportunities for optimization. Energy Efficiency Measures were then formulated, focusing on improving energy efficiency while focusing on energy consumption reduction and GHG emission reduction. Results demonstrated the potential of Energy Audits and Modeling to enable significant reductions in energy consumption and promote sustainable building practices. Among the Energy Efficiency Measures considered, re-sizing and decarbonizing HVAC equipment contributed the most to energy savings, with a 100% decrease in natural gas and 37% decrease in electricity use annually.

This study aimed to develop a laboratory-scale direct air capture unit for evaluating and comparing amine-based adsorbents under temperature vacuum swing adsorption conditions. The experimental campaign conducted with the direct air capture unit allowed for the determination of equilibrium loading, CO2 uptake capacity, and other main performance parameters of the investigated adsorbent Lewatit VP OC 1065®. The investigations also helped to understand the co-adsorption of both CO2 and H2O on the tested material, which is crucial for improving temperature vacuum swing adsorption processes. This was achieved by obtaining pure component isotherms for CO2 and H2O as well as three different co-adsorption isotherm models from literature. It was found that the weighted average dual-site Toth model emerged as the most accurate and reliable model for simulating this co-adsorption behavior. Its predictions closely align with experimental data, particularly in capturing the adsorption equilibrium at various temperatures. It was also observed that this lab-scale unit offers advantages over thermogravimetric analysis when conducting adsorption experiments on the chosen amine. The final aim of this study is to provide a pathway to develop devices for testing and developing efficient and cost-effective adsorbents for direct air capture.

Coffee is regarded as the highly consumed beverage throughout the world and has established a key spot in the world economy as an important commodity for trading. In general, they are produced by brewing their roasted and ground beans, which release aromatic coffee; as well as produce an equivalent amount of spent coffee grounds (SCG). Previously, they were discarded as wastes or used as natural pest repellent or garden fertilizer; however, in recent times, are valorized into biofuels owing to their high calorific value. In fact, SCG briquettes have gained wide attention for supplying energy renewably, especially to the rising energy demand; and also have been identified as an effective measure to reduce their pollution. With this in mind, this present chapter focuses on reviewing the availability and chemistry involved in these SCG wastes, pre-treatments and preparations required for their briquetting, compacting techniques followed, and fuel characteristics of their briquettes, from various available works of literature. Here, their availability showcases the amount of SCG wastes generated with respect to time and consumption, wherein understanding their chemistry helps in deciding the pre-treatments necessary for their briquetting. Meanwhile, preparation techniques briefs about the necessary pre-treatments undertaken before compaction by different researchers; and the fuel characteristics define the physicochemical and mechanical properties of their briquettes, developed using various compaction methods. Besides, combustion behaviors of these briquettes are explained in terms of their burning characteristics and emission levels, as reported in literatures; which help in deciding their suitability as a replacement for existing fossil coal. Eventually, all the reported data were in accordance with their permissible standards and suggested these SCG as a highly renewable solid biofuel.

Cashew nut shells (CNS) are the primary waste produced during the processing of cashew nuts; and needs constant attention to handle or valorize these wastes effectively. As a result, these CNS wastes are processed into solid briquettes citing their significant calorific content, thus making them as a promising renewable biofuel for combustion based applications. In most cases, these wastes are pre-treated either through de-oiling or carbonizing prior to compaction, thus removing the harmful hydrocarbons present in them in form of CNS liquids. Presently, this chapter focus on summarising various data related to these CNS wastes and their briquettes in terms of their availability, chemical characteristics, pre-treatment and processing technique, fuel and combustion properties as reported in various literatures. Here, availability depicts the current trend in global consumption of these snack nuts and the proportionate amount of waste shells produced; while, chemical characteristics focused on discussing their anatomy, proximate, lignocellulosic and elemental compositions. Following this, pre-treatment and processing techniques list out the various practises followed to remove CNSL, process de-oiled CNS cakes into bio-char through carbonization, and briquetting of pre-treated CNS wastes along with their compacting techniques prescribed by various researchers. Lastly, fuel and combustion properties brief out about the fuel traits of developed CNS briquettes along with their burning characteristics; and include parameters like proximate and elemental compositions, density and compressive strength, and results related to their combustion and water boiling tests. Moreover, all the reported results and data in this study were in accordance with the international testing standards; and ranged in between their permissible range.

Briquetting of biomass is an ideal technique for improvising both its volumetric and net energy density; besides, serving as an effective means for reducing pollution. In general, numerous biomass and organic by-products are discarded as wastes, citing their non-edibility, composition of chemical compounds present in their raw form, in addition to their zero usage value. Yet, these biomass wastes hold significant heating values, which promote them into promising solid biofuels, either in their existing or pre-treated form. Accordingly, this review article discusses about the various biomasses used as raw feedstock for briquetting, besides summarising the works carried out in relevance to their respective briquettes. In addition, proximate and lignocellulosic composition of these biomasses, and their pre-treatment techniques followed to prepare them for briquetting, have also been discussed. This study suggested that the heating value of biomasses ranged between 10-20 MJ/kg, whilst, their briquettes reported between 15 and 25 MJ/kg; thereby citing their potential as viable replacement for existing fossil coals. Besides, factors affecting different thermal and physicochemical properties of these briquettes have also been studied and concluded that these properties play a crucial role in deciding the overall quality of the briquettes. Ultimately, this study proposed that any biomass with good calorific value and lignin content can be processed into briquettes with good strength and durability; however, the choice of biomass will also be accounted for by its availability, geographical distribution, and handleability.

This short technical note proves some observed novel corollaries of the Collatz Conjecture. For this, a unique ‘Collatz Representation’ of Hailstone numbers has been employed. After that, an extension of this corollary is explained using the fact that only certain differences in the last digit of the ‘Collatz Representation’ gives a whole number difference between numbers. A more general result is obtained. The final proof is for a corollary that some numbers the same number of steps to reach 1 if the Collatz Conjecture is true and all variables are whole numbers.

Structural and functional materials are subjected to harsh oxidizing environments that lead to a rapid decline in their surface chemical stability. At high-temperatures, the diffusion of atoms is erratic; thus, the reactive elements (REs) get a chance to migrate to the surface and look for oxygen-reactive sites. Their migration from the lattice sites creates vacancies in the matrix and thus weakens the bond, making the material prone to environmental degrading factors. Subsequently, the inward diffusion of oxygen, sulfur, nitrogen, or carbon may occupy these vacancies, resulting in undesired precipitation at the grain boundary, which is usually brittle. The solubility and dissociation of attacking species and corrosion products play the most critical role in corrosion in high-temperature water. To evade such situations, Ti, Al, and Cr are added in Ni/Fe-based alloys, forming a dense oxide layer on the surface that impedes further surface migration of ions. The stability of the alloys is then determined by the capability of these oxide layers to heal or reform during spalling/cracking. This review attempts to understand the migration of REs at the interfaces to prepare structural materials in any unexpected set of oxidizing service conditions. This review will also try to establish the interaction mechanism of REs novel/conventionally added in the alloys with the oxidizing elements in the environments to design better degradation-resistant high-temperature alloys.

SARS-CoV 2 also known as COVID-19 is a fast spreading coronavirus related disease that emerged from China in December 2019 and is currently attained the status of a pandemic. There are currently no drugs/ vaccines against the same and moreover limited diagnostic tests to identify the infection. Additionally, these tests are expensive and hence are exclusive for very highly suspected cases of the disease especially in developing countries. This is causing an under-diagnosis which is an alarming state of affairs, as even a single missed SARS-CoV 2 case would spread the disease exponentially and keep it in the community. Through this entirely in silico study, we have developed a cheaper and faster diagnostic method based on simple PCR and restriction enzyme digestion, commonly used in restriction fragment length polymorphism (RFLP) tests. Through comparative genomics, we found the closest neighbours of SARS-CoV 2 then found the highly conserved regions of the genome which were absent in SARS-CoV 1, its closest neighbour. Then we found restriction sites for various enzymes followed by designing of PCR primers flanking those sites. We have found the primer pair to produce a 401 bp amplicon and when digested by SwaI enzyme, it produces two fragments of lengths 216 bp and 185 bp. As an internal control, GAPDH primers are pooled with the SARS-CoV 2 primers as the patient sample will also include human RNA mixed with the viral RNA. This primer pair gives an amplicon of 131 bp and hence a negative sample should show a single band of 131 bp while a positive digested sample will give three bands of 401 bp, 216 bp and 131 bp. The primers are specific to SARS-CoV 2 only and can additionally be used for SYBR green based real time quantification of viral load. The developed tests have not yet been tested in vitro due to stressed out working hours in the only pathogenic virus handling laboratory in our institute. Nonetheless, this study works as a head start for other laboratories to rapidly test the suggested protocols in vitro and make available a cheaper alternative test for SARS-CoV 2 which would especially be beneficial for the lower to middle income countries.

The question of molecular similarity is core in cheminformatics, and is usually assessed via a pairwise comparison based on vectors of properties or molecular fingerprints. We recently exploited variational autoencoders to embed 6M molecules in a chemical space, such that their (Euclidean) distance within the latent space so formed could be assessed within the framework of the entire molecular set. However, the standard objective function used did not seek to manipulate the latent space so as to cluster the molecules based on any perceived similarity. Using a set of some 160,000 molecules of biological relevance, we here bring together three modern elements of deep learning to create a novel and disentangled latent space, viz transformers, contrastive learning, and an embedded autoencoder. The effective dimensionality of the latent space was varied such that clear separation of individual types of molecules could be observed within individual dimensions of the latent space. The capacity of the network was such that many dimensions were not populated at all. As before, we assessed the utility of the representation by comparing clozapine with its near neighbours, and did the same for various antibiotics related to flucloxacillin. Transformers, especially when as here coupled with contrastive learning, effectively provide one-shot learning, and lead to a successful and disentangled representation of molecular latent spaces that at once uses the entire training set in their construction while allowing ‘similar’ molecules to cluster together in an effective and interpretable way.

Soybean yield prediction is a challenging problem in plant breeding that is often affected by many different factors simultaneously. Hyperspectral reflectance data from plants and soil data provide breeders with useful information about soybean plant health and using these different types of data to predict yield is an active area of research. Furthermore, breeding programs encounter challenges such as data imbalance and external factors like genotype variability across different environments, which present significant hurdles in the development of yield prediction models for large-scale breeding programs. In this work, we perform a comprehensive study of predicting yield using both hyperspectral reflectance and soil data to understand what scenario's offer the best chances of predicting yield with high accuracy. We demonstrate a cluster based ensemble approach for yield prediction using hyperspectral reflectance data that can perform well for large scale breeding programs by efficiently harnessing useful information from data through an unsupervised approach.

Pipelines are widely used for transportation of hydrocarbon fluids over millions of miles over the world. The structures of the pipelines are designed to withstand several environmental loading conditions to ensure safe and reliable distribution from point of production to the shore or distributions deport. However, leaks in pipeline networks are one of the major causes of innumerable losses in pipeline operators and nature. Incidents of pipeline failure can result in serious ecological disasters, human casualties and financial loss. In order to avoid such menace and maintain safe and reliable pipeline infrastructure, substantial research efforts have been devoted to implementing pipeline leak detection and localisation using different approaches. This paper discusses on pipelines leakage detection technologies and summarises the state-of-the-art achievements. Different leakage detection and localisation in pipeline systems are reviewed and their strengths and weaknesses are highlighted. Comparative performance analysis is performed to provide a guide in determining which leak detection method is appropriate for particular operating settings. In addition, research gaps and open issues for development of reliable pipeline leakage detection systems are discussed.

In this study, we introduce a neural-learning based approach for the early detection of Parkinson Disease using DaT SPECT imaging, a promising technique in neurodegenerative disease diagnosis. Leveraging the advanced capabilities of deep learning, we developed a convolutional neural network model based on the Inception V3 architecture, which has been enhanced by modulating custom layers to fine-tune the model specifically for the analysis of DaT SPECT images. The imaging dataset was obtained through the Parkinson's Progression Markers Initiative (PPMI), and the model was trained to classify whether a patient had Parkinson Disease through a binary classification of their DaT SPECT Scan using the fine-tuned InceptionV3 model. This specialized adaptation allows for more accurate and nuanced interpretation of the scans, a crucial factor in early and reliable diagnosis of Parkinsonian syndromes. Our model underwent rigorous hyperparameter tuning, focusing on learning rates, the number of neurons in the dense layer, and dropout rates, to ensure optimal performance. Remarkably, the proposed model demonstrated a significant improvement in accuracy, achieving 74.65%, compared to a standard Sequential Model, which only reached an accuracy of 51.41%. Diagnosis of Parkinson Disease through DaT SPECT Scans is a promising approach not only as a more effective diagnostic tool but also as a beacon for future research in the application of deep learning to medical imaging for neurodegenerative diseases. By building layers on the InceptionV3 Architecture, we achieve a higher accuracy on DaT SPECT Scan diagnosis and pave the way for automated diagnosis of patients with Parkinson Disease, allowing for easier medical accessibility and paving the way for advancements in early diagnosis and personalized medicine strategies for Parkinson's disease and related disorders.

We explore the use of inverse multiquadratic (IMQ) functions as basis functions when solving the vibrational Schrödinger equation with the rectangular collocation method. The quality of the vibrational spectrum of formaldehyde (in six dimensions) is compared to that obtained using Gaussian basis functions when using different numbers of width-optimized IMQ functions. The effects of the ratio of the number of collocation points to the number of basis functions and of the choice of the IMQ exponent are studied. We show that the IMQ basis can be used with parameters where the IMQ function is not integrable. We find that the quality of the spectrum with IMQ basis functions is somewhat lower that that with a Gaussian basis when the basis size is large and for a range of IMQ exponents. The IMQ functions are, however, advantageous when a small number of functions is used or with a small number of collocation points e.g. when using square collocation.

Miniaturization of electronics devices is often limited by the concomitant high heat fluxes (cooling load) and maldistribution of temperature profiles (hot spots). Thermal energy storage (TES) platforms providing supplemental cooling can be a cost-effective solution, that often leverages phase change materials (PCM). Although salt hydrates provide higher storage capacities and power ratings (as compared to that of the organic PCMs), they suffer from reliability issues (e.g., supercooling). ‘Cold Finger Technique (CFT)’ can obviate supercooling by maintaining a small mass fraction of the PCM in solid state for enabling spontaneous nucleation. Optimization of CFT necessitates real-time forecasting of the transient values of the melt-fraction. In this study artificial neural network (ANN) is explored for real-time prediction of the time remaining to reach a target value of melt-fraction based on the prior history of the spatial distribution of the surface temperature transients. Two different approaches were explored for training the ANN model, using: (1) transient PCM-temperature data; or (2) transient surface-temperature data. When deployed in a heat sink that leverages PCM based passive thermal management systems for cooling of electronic chips and packages, this maverick approach (using the second method) affords cheaper costs, better sustainability, higher reliability and resilience.

The objective of the study was to report the health-related quality of life (HRQOL) following road traffic accidents (RTAs) among children. A community-based survey using EuroQol five-dimension questionnaire (EQ-5D-5L) in Hindi was used to collected data from community. The survey included 2620 households from urban and rural areas of Ujjain, India. From these households 229 children aged 5–18 years with a history of RTA in the last 1 year were identified, with 27%, 63%, and 10% children reporting mild, moderate, and severe injury based on length of hospitalization. Motorcycles, bicycles, and pedestrians constituted most RTAs. Helmet use was low (12%). EQ-5D-5L revealed that the most severe and extreme problem was pain and discomfort, whereas the least severe problem was usual activity and self-care. The most common (65%) injuries were either abrasion or fracture and dislocation. EQ-5D-5L severity index was maximum (mean 72) for lower extremity injuries. The results of the present study highlight the ability and requirement for quality of life measurement using EQ-5D-5L among children post-RTA.

The ‘inverse problem’ of mass spectrometric molecular identification (‘given a mass spectrum, calculate/predict the 2D structure of the molecule whence it came’) is largely unsolved, and is especially acute in metabolomics where many small molecules remain unidentified. This is largely because the number of experimentally available electrospray mass spectra of small molecules is quite limited. However, the forward problem (‘calculate a small molecule’s likely fragmentation and hence at least some of its mass spectrum from its structure alone’) is much more tractable, because the strengths of different chemical bonds are roughly known. This kind of molecular identification problem may be cast as a language translation problem in which the source language is a list of high-resolution mass spectral peaks and the ‘translation’ a representation (for instance in SMILES) of the molecule. It is thus suitable for attack using the deep neural networks known as transformers. We here present MassGenie, a method that uses a transformer-based deep neural network, trained on ~6 million chemical structures with augmented SMILES encoding and their paired molecular fragments as generated in silico, explicitly including the protonated molecular ion. This architecture (containing some 400 million elements) is used to predict the structure of a molecule from the various fragments that may be expected to be observed when some of its bonds are broken. Despite being given essentially no detailed nor explicit rules about molecular fragmentation methods, isotope patterns, rearrangements, neutral losses, and the like, MassGenie learns the effective properties of the mass spectral fragment and valency space, and can generate candidate molecular structures that are very close or identical to those of the ‘true’ molecules. We also use VAE-Sim, a previously published variational autoencoder, to generate candidate molecules that are ‘similar’ to the top hit. In addition to using the ‘top hits’ directly, we can produce a rank order of these by ‘round-tripping’ candidate molecules and comparing them with the true molecules, where known. As a proof of principle, we confine ourselves to positive electrospray mass spectra from molecules with a molecular mass of 500Da or lower, including those in the last CASMI challenge (for which the results are known), getting 49/93 (53%) precisely correct. The transformer method, applied here for the first time to mass spectral interpretation, works extremely effectively both for mass spectra generated in silico and on experimentally obtained mass spectra from pure compounds. It seems to act as a Las Vegas algorithm, in that it either gives the correct answer or simply states that it cannot find one. The ability to create and to ‘learn’ millions of fragmentation patterns in silico, and therefrom generate candidate structures (that do not have to be in existing libraries) directly, thus opens up entirely the field of de novo small molecule structure prediction from experimental mass spectra.

We report a theoretical derivation of the Cabibbo-Kobayashi-Maskawa (CKM) matrix parameters and the accompanying mixing angles. These results are arrived at from the exceptional Jordan algebra applied to quark states, and from expressing flavor eigenstates (i.e. left-chiral states) as superposition of mass eigenstates (i.e. the right-chiral states) weighted by square-root of mass. Flavor mixing for quarks is mediated by the square-root mass eigenstates, and the mass ratios used have been derived in earlier work from a left-right symmetric extension of the standard model. This permits a construction of the CKM matrix from first principles. There exist only four normed division algebras, they can be listed as follows - the real numbers $\mathbb{R}$, the complex numbers $\mathbb{C}$, the quaternions $\mathbb{H}$ and the octonions $\mathbb{O}$. The first three algebras are fairly well known; however, octonions as algebra are less studied. Recent research has pointed towards the importance of octonions in the study of high energy physics. Clifford algebras and the standard model are being studied closely. The main advantage of this approach is that the spinor representations of the fundamental fermions can be constructed easily here as the left ideals of the algebra. Also the action of various Spin Groups on these representations too can be studied easily. In this work, we build on some recent advances in the field and try to determine the CKM angles from an algebraic framework. We obtain the mixing angle values as $\theta_{12}=11.093^o, \theta_{13}=0.172^o, \theta_{23}=4.054^o$. In comparison, the corresponding experimentally measured values for these angles are $13.04^o \pm 0.05^o, 0.201^o \pm 0.011^o, 2.38^o \pm 0.06^o $. The agreement of theory with experiment is likely to improve when running of quark masses is taken into account.

Gravity played an important role in the development of life on earth. The effect of gravity on a living organisms can be investigated by controlling the magnitude of gravity. Most reduced gravity experiments are conducted on the lower earth orbit (LEO) in the International Space Station (ISS). However, running experiments in ISS face challenges such as high cost, extreme condition, lack of direct accessibility, and long waiting period. Therefore, researchers have developed various ground-based devices and methods to perform reduced gravity experiments. However, the search for life outside the earth requires more intensive research. Advancements in conventional methods and the development of new tools are required for this purpose. The advantages of Lab-on-a-Chip (LOC) devices make them an attractive option for simulating microgravity. This paper briefly reviews the advancement of LOC technologies for simulating microgravity in a earth-based laboratory.

Artificial Intelligence (AI) systems involve diverse components, such as data, models, users and predicted outcomes. To elucidate these different aspects of AI systems, multifaceted explanations that combine diverse explainable AI (XAI) methods are beneficial. However, popularly adopted user-centric XAI evaluation methods do not measure these explanations across the different components of the system. In this position paper, we advocate for an approach tailored to evaluate XAI methods considering the diverse dimensions of explainability within AI systems using a normalised scale. We argue that the prevalent user-centric evaluation methods fall short of facilitating meaningful comparisons across different types of XAI methodologies. Moreover, we discuss the potential advantages of adopting a standardised approach, which would enable comprehensive evaluations of explainability across systems. By considering various dimensions of explainability, such as data, model, predictions, and target users, a standardised evaluation approach promises to facilitate both inter-system and intra-system comparisons for user-centric AI systems.

Diarrhoea contributes significantly in the under-five childhood morality and mortality worldwide. This cross-sectional study was carried out in a tertiary care hospital in Ujjain, India from July 2015 to June 2016. Consecutive children aged 1 month to 12 years having “some dehydration” and “dehydration” according to World Health Organization classification were eligible to be included in the study. Other signs and symptoms used to assess severe dehydration were capillary refill time, urine output, and abnormal respiratory pattern. A questionnaire was administered to identify risk factors for severe dehydration, which was the primary outcome. Multivariate logistic regression modeling was used to detect independent risk factors for severe dehydration. The study included 332 children, with mean ± standard deviation age of 25.62 ± 31.85 months; out of which, 70%(95% confidence interval [CI] 65 to 75) were diagnosed to have severe dehydration. The independent risk factors for severe dehydration were: child not exclusive breast fed in the first six months of life (AOR 5.67, 95%CI 2.51 to 12.78; p<0.001), history of not receiving oral rehydration solution before hospitalization (AOR 1.34, 95%CI 1.01 to 1.78; p=0.038), history of not receiving oral zinc before hospitalization (AOR 2.66, 95%CI 1.68 to 4.21; p<0.001) and living in overcrowded conditions (AOR 5.52, 95%CI 2.19 to 13.93; p<0.001). The study identified many risk factors associated with severe childhood dehydration; many of them are modifiable though known and effective public health interventions.

Significant progress has been made in understanding the computational and neural architecture that mediates eye and hand movements made in isolation. However, less is known about the mechanisms that control these movements when they are coordinated. Here, we outline our computational approaches using accumulation-to-threshold and race-to-threshold models to elucidate the mechanisms that initiate and inhibit these movements. We suggest that, depending on the behavioral context, the initiation and inhibition of coordinated eye-hand movements can operate in two modes- coupled and decoupled. The coupled-mode operates when the task context requires a tight coupling between the effectors; a common command initiates both effectors, and a unitary inhibitory process is responsible for stopping them. Conversely, the decoupled mode operates when the task context demands weaker coupling between the effectors; separate commands initiate the eye and hand, and separate inhibitory processes are responsible for stopping them. We hypothesize that higher-order control processes assess the behavioral context and choose the most appropriate mode. This computational architecture can explain heterogeneous results observed across many studies that have investigated the control of coordinated eye-hand movements and may also serve as a general framework to understand the control of complex multi-effector movements.

Favipiravir is a broad-spectrum inhibitor of viral RNA-dependent RNA polymerase (RdRp) currently being used to manage COVID-19 in several countries. By acting as a substrate for RdRp, favipiravir gets incorporated into the nascent viral RNA and prevents strand extension. A high mutation rate of SARS-CoV-2 RdRp may facilitate antigenic drift as an answer to the host immune response, thereby generating resistance of virus to favipiravir. Therefore, it is extremely crucial to predict potential mutational sites in the RdRp and the emergence of structural modifications contributing to drug resistance. Here, we used high-throughput interface-based protein design to generate >100,000 designs and identify mutation hotspot residues in the favipiravir-binding site of RdRp. Several mutants had lower binding affinities to favipiravir, out of which hotspot residues with a high propensity to undergo positive selection were identified. The results showed that the designs retained an average of 97 to 98% sequence identity, suggesting that SARS-CoV-2 can develop favipiravir resistance with just a few mutations. Notably, we observed that out of 134 mutations predicted designs, 63 specific mutations were already present in the CoV-GLUE database, thus attaining ~47% correlation match with the clinical sequencing data. The findings improve our understanding of the potential signatures of adaptation in SARS-CoV-2 against favipiravir and management of COVID-19. Furthermore, they can help develop exhaustive strategies for robust antiviral design and discovery.

Screen viewing time is the total time spent by a child on any digital/electronic device. The objective of the present study was to determine the incidence and predictors of excessive screen viewing time in children in Ujjain, India. This cross-sectional, community-based study was conducted through house-to-house survey by using the three-stage cluster sampling method in 36 urban wards and 36 villages of Ujjain district, India. Excessive screen viewing time was defined as screen viewing for &gt; 2 h/day. The prevalence of excessive screen viewing time was 17.83%. Risk factors identified using the multivariate logistic regression model were: age (OR: 1.5, P &lt; 0.001); mobile phone use before bedtime (OR: 3.17, P = 0.008); parents’ perception about the child habituated to screen (OR: 14.03, P &lt; 0.001); television in bedroom (OR: 48.69, P &lt; 0.001); morning mobile screen viewing time (OR: 9.27, P &lt; 0.001); not reading books other than textbooks (OR: 9.71, P &lt; 0.001); and lack of outdoor play for &gt;2 h (OR: 4.20, P &lt; 0.001). Presence of eye pain was a protective factor for excessive screen viewing time (OR: 0.12, P = 0.011). The study identified multiple modifiable risk factors for excessive screen viewing time.

Background: The Covid-19 pandemic abruptly disrupted global healthcare systems, necessitating rapid adaptations. This study evaluates the impact on health systems and services in the aftermath of the first wave in the Indian context. It analyses the disruptions, adaptive measures, and changes made, as well as the challenges faced by healthcare providers and seekers. Valuable insights from this study will enhance the resilience and preparedness of healthcare systems for future challenges. Methods: The eligible studies included primary studies conducted in the Indian context that explore the impact of COVID-19 on health services provision, utilisation, and the well-being of healthcare providers and seekers. Electronic searches were conducted in six databases: PubMed, MEDLINE, Embase, Global Health, CINAHL, and the WHO database on COVID-19. The results were analysed using detailed narrative synthesis. Results: The review includes 38 articles, incorporating a total of 22,502 subjects. There has been a substantial impact on health service provision, particularly in outpatient departments (OPD) (n=19) and elective services (n=16), while emergency services continued at sub-optimal levels (n=20). Various adaptations and changes were implemented in precautionary measures, protocols, staff allocation and training, usage of personal protective equipment (PPE), preoperative, operative, and postoperative measures, as well as physical infrastructure and resources. Depression and stress (n=14), fear of contracting the infection (n=6), stigmatisation (n=5), and financial repercussions (n=5) significantly affected the mental health of healthcare providers, and healthcare seekers also faced significant challenges (n=11). Conclusion: The study reveals COVID-19's substantial impact on health services. The healthcare system responded by quickly adjusting staff management, resource allocation, and infection prevention measures. The study also highlights the mental health challenges faced by healthcare providers and the concerns of healthcare seekers regarding delays and suboptimal care. Looking ahead, the findings underscore the importance of preparedness for future pandemics, including improved healthcare infrastructure, resource optimisation, and comprehensive protocols. Lessons learned from COVID-19 should inform strategies to mitigate disruptions and ensure the well-being of healthcare providers and seekers in future outbreaks.

Childhood diarrhea continues to be a major cause of under-five (U-5) mortality globally and in India. In this study, 1571 U-5 children residing in nine rural villages and four urban slums in Ujjain, India were included with the objective to use community participation and drug utilization research to improve diarrheal case management. The mean age was 2.08 years, with 297 (19%), children living in high diarrheal index households. Most mothers (70%) considered stale food, teething (62%), and hot weather (55%) as causes of diarrhea. Water, sanitation, and hygiene (WASH)-related characteristics revealed that most (93%) households had toilets, but only 23% of the children used them. The study identified ineffective household water treatment by filtration through cloth by most (93%) households and dumping of household waste on the streets (89%). The results revealed low community awareness of correct causes of diarrhea (poor hand hygiene, 21%; littering around the household, 15%) and of correct diarrhea treatment (oral rehydration solution (ORS) and zinc use, 29% and 11%, respectively) and a high antibiotic prescription rate by healthcare providers (83%). Based on the results of the present study, context-specific house-to-house interventions will be designed and implemented.

Background: There is lack of data on types of community first aids use and treatment given post injuries from many low-middle income countries, including India. Materials and Methods: A cross-sectional study was conducted among children up-to 18 years of age, in Ujjain district, India to understand types of first aid given and health seeking post injury. Results: A total of 1087 injuries, in 1049 children were identified in last one year, 729 (67%) received, first aid and 758 (72%) sought some healthcare. Children with burns received most (86%) first aid, while most children (84%) with road traffic accidents (RTA) sought health care. Most children (52%) sought healthcare from a private health set-up; most (65%) being transported within the golden hour; motorbikes being the most preferred (50%) mode of transport. Only 1% injured used ambulance services. Commonly reported first aid included: use of coconut oil on wounds from falls (38%) and burns (44%); antiseptic cream on wounds from RTA (31%), turmeric in falls (16%), and rubbing of metal on a bitten site (47%). Potentially harmful substances applied included lime, toothpaste, clay and mud. Conclusion: In most injuries, appropriate locally available substances, were used by the community. Our findings will help design community interventions to increase appropriate first aid in childhood injuries.

Since December 2019, the world is fighting against coronavirus disease (COVID-19). This disease is caused by a novel coronavirus termed as severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). This work focuses on the applications of machine learning algorithms in the context of COVID-19. Firstly, regression analysis is performed to model the number of confirmed cases and death cases. Our experiments show that autoregressive integrated moving average (ARIMA) can reliably model the increase in the number of confirmed cases and can predict future cases. Secondly, a number of classifiers are used to predict whether a COVID-19 patient needs to be admitted to an intensive care unit (ICU) or semi-ICU. For this, classification algorithms are applied to a dataset having 5644 samples. Using this dataset, the most significant attributes are selected using features selection by ExtraTrees classifier, and Proteina C reativa (mg/dL) is found to be the highest-ranked feature. In our experiments, random forest, logistic regression, support vector machine, XGBoost, stacking and voting classifiers are applied to the top 10 selected attributes of the dataset. Results show that random forest and hard voting classifiers achieve the highest classification accuracy values near 98%, and the highest recall value of 98% in predicting the need for admission into ICU/semi ICU units.

Biases in Artificial Intelligence (AI) or Machine Learning (ML) systems due to skewed datasets problematise the application of prediction models in practice. Representation bias is a prevalent form of bias found in the majority of datasets. This bias arises when training data inadequately represents certain segments of the data space, resulting in poor generalisation of prediction models. Despite AI practitioners employing various methods to mitigate representation bias, their effectiveness is often limited due to a lack of thorough domain knowledge. To address this limitation, this paper introduces human-in-the-loop interaction approaches for representation debiasing of generated data involving domain experts. Our work advocates for a controlled data generation process involving domain experts to effectively mitigate the effects of representation bias. We argue that domain experts can leverage their expertise to assess how representation bias affects prediction models. Moreover, our interaction approaches can facilitate domain experts in steering data augmentation algorithms to produce debiased augmented data and validate or refine the generated samples to reduce representation bias. We also discuss how these approaches can be leveraged for designing and developing user-centred AI systems to mitigate the impact of representation bias through effective collaboration between domain experts and AI.

Lysine is the first limiting essential amino acid in rice because it is present in the lowest quantity compared to all the other amino acids. Amino acids are the building block of proteins and play an essential role in maintaining the human body’s healthy functioning. Rice is a staple food for large proportion of the global population, thus increasing the lysine content in rice will improve its nutritional value. In this paper, we studied the lysine biosynthesis pathway in rice (Oryza Sativa) to identify the regulators of the lysine reporter gene LYSA (LOC_Os02g24354). Genetically intervening at the regulators has the potential to increase the overall lysine content in rice. We modeled the lysine biosynthesis pathway in rice seedlings under normal and saline (NaCl) stress conditions using Bayesian networks. We estimated the model parameters using experimental data and identified the gene DAPF(LOC_Os12g37960) as a positive regulator of the lysine reporter gene LYSA under both normal and saline stress conditions. Based on this analysis, we conclude that the gene DAPF is a potent candidate for genetic intervention. Upregulating DAPF using methods such as CRISPR-Cas9 has the potential to upregulate the lysine reporter gene LYSA and increase the overall lysine content in rice.

Drilling vibrations has been identified as a key performance limiter that prevents successful energy transfer from the surface to the bit. The resultant irregular bit rotation speed causes drilling challenges like poor hole quality and reduction in rate of penetration to name a few. Amongst other vibration suppression techniques, active control of vibrations is widely used and recommended. Active control system utilizes a closed loop feedback control to continuously adapt to downhole vibrations detected at the surface. The system requires regular tuning and upgrades which is done experimentally before field deployment. The paper presents a PID based experimental tuning of horizontal and vertical strings for irregular RPM. In doing so, the paper highlights the need of having horizontal experimental setups for state-of-the-art PID tuning for downhole RPM. The settling time of irregular RPM for horizontal setup is found to be lower than the vertical configuration due to multiple contact points and increased friction coefficient.

Coronavirus disease 2019 (COVID-19) is an emerging infectious disease that was first reported in Wuhan, China and has subsequently spread worldwide. In the absence of any antiviral or immunomodulatory therapies, the disease is spreading at an alarming rate. 5 to 10% of recovered patients in Wuhan test positive again; this suggest that for controlling COVID-19, vaccines may be better option than drugs. A clinical trial to evaluate an anti-COVID-19 vaccine has started recently. However, its efficacy and potency have to be evaluated and validated. As an alternative, we are presenting a first-of-its-kind, designed multi-peptide subunit based epitope vaccine against COVID-19. The vaccine construct comprise an adjuvant, CTL, HTL, and B-cell epitopes joined by linkers. The vaccine is non-toxic, non-allergenic, thermostable and immunogenic with the capability to elicit a humoral and cell-mediated immune response. The findings are validated with high-end computation-based methods. This unique vaccine is made up of 33 highly antigenic epitopes from three proteins that have a prominent role in host receptor recognition, viral entry, and pathogenicity. We advocate this vaccine must be synthesized and tested urgently as public health priority.

The signaling complex around voltage-gated sodium (Nav) channels includes accessory proteins and kinases crucial for regulating neuronal firing. Previous studies showed that one such kinase, WEE1—critical to the cell cycle—selectively modulates Nav1.2 channel activity through the accessory protein fibroblast growth factor 14 (FGF14). Here, we tested whether WEE1 exhibits crosstalk with the AKT/GSK3 pathway for coordinated regulation of FGF14/Nav1.2 channel complex assembly and function. Using the in-cell split luciferase complementation assay (LCA), we found that the WEE1 inhibitor II and GSK3 inhibitor XIII reduce FGF14/Nav1.2 complex formation, while the AKT inhibitor triciribine increases it. However, combining WEE1 inhibitor II with either one of the other two inhibitors abolished its effect on FGF14/Nav1.2 complex formation. Whole-cell voltage-clamp recordings of sodium currents (INa) in HEK293 cells co-expressing Nav1.2 channels and FGF14-GFP showed that WEE1 inhibitor II significantly suppresses peak INa density, both alone and in the presence of triciribine or GSK3 inhibitor XIII, despite the latter inhibitors’ opposite effects on INa. Additionally, WEE1 inhibitor II slowed the tau of fast inactivation, and caused depolarizing shifts in the voltage dependence of activation and inactivation. These phenotypes either prevailed or were additive when combined with triciribine but were outcompeted when both WEE1 inhibitor II and GSK3 inhibitor XIII were present. Concerted regulation by WEE1 inhibitor II, triciribine and GSK3 inhibitor XIII were also observed on long-term inactivation and use-dependence of Nav1.2 currents. Overall, these findings suggest a complex role for WEE1 kinase—in concert with the AKT/GSK3 pathway—in regulating the Nav1.2 channelosome.

Yogyakarta City is one of the big city which is located in Java Island, Indonesia. Yogyakarta City, including study area (Pleret Sub District), are very prone to earthquake hazards, because close to several active earthquake sources. For example, Sunda Megathrust which often generates a big earthquake which can affect the study area. The Sunda Megathrust extends from north to south and west to east along the Sumatra and Java Islands. Furthermore, an active normal fault called as Opak Fault pass through right in the middle of Study area and divides the study area into east and west zone. Recently, after the devastating earthquake in 2006, the population of the study area increases significantly. As a result, the housing demand is also increasing. However, due to the absence of earthquake building code in the study area, locals tend to build improper new houses. Furthermore, in some part of the mountainous area in the study area, there are some building found in unstable slopes area. Due to this condition, the multi-hazard and risk study needs to be done in Pleret. The increasing of population and improper houses in Pleret Sub-District can lead to amplify the impact. Thus, the main objective of this study is to assess the multi-hazards and risk of earthquake and other related secondary hazards such as ground amplification, liquefaction, and coseismic landslide. The method mainly utilised the geographic information system, remote sensing and was fit up by the outcrop study. The results show that the middle part of the study area has a complex geological structure. It was indicated by a lot of unchartered faults was found in the outcrops. Furthermore, the relatively prone areas to earthquake can be determined. In term of the coseismic landslide, the prone area to the coseismic landslide is located in the east part of the study area in the middle slope of Baturagung Escarpment. The highly potential area of liquefaction is dominated in the central part of the study area. In term of building collapsed probability, the result shows that the safest house based on statistical analysis is the residential house with the building attribute of wood structure, roof cast material, distance more than 15 km from the earthquake source, and located above the Nglanggran Formation. Finally, the multi-hazard and risk analysis show that the middle part of the study area is more vulnerable than the other part of Pleret Sub-District.

Very little is known about laboratory confirmed blood stream infections (LCBIs) in neonatal intensive care units (NICUs) in resource-limited settings. The aim of this cohort study was to determine the incidence, risk factors, and causative agents of LCBIs in a level-2 NICU in India. The diagnosis of LCBIs was established using the Centre for Disease Control, USA criteria. A predesigned questionnaire containing risk factors associated with LCBIs was filled-in. A total of 150 neonates (43% preterm) were included in the study. The overall incidence of LCBIs was 31%. The independent risk factors for LCBIs were: preterm neonates (relative risk (RR) 2.23), duration of NICU stay more than 14 days (RR 1.75), chorioamnionitis in the mother (RR 3.18), premature rupture of membrane in mothers (RR 2.32), neonate born through meconium-stained amniotic fluid (RR 2.32), malpresentation (RR 3.05), endotracheal intubation (RR 3.41), umbilical catheterization (RR 4.18), and ventilator-associated pneumonia (RR 3.17). The initiation of minimal enteral nutrition was protective from LCBIs (RR 0.22). The predominant causative organisms were gram-negative pathogens (58%). The results of the present study can be used to design antibiotic interventions to reduce LCBIs in resource-limited settings.

Curcumin, a hydrophobic polyphenol compound derived from the rhizome of the Curcuma genus, has a wide spectrum of biological and pharmacological applications. Previously, curcumin nanoparticles with different stabilizers had been produced successfully in order to enhance solubility and per oral absorption. In the present study, we tested the anti-inflammatory effect of D-α-Tocopheryl polyethylene glycol 1000 succinate (TPGS)-stabilized curcumin nanoparticles in vivo. Lambda-carrageenan (λ-carrageenan) was used to induce inflammation in rats; it was given by an intraplantar route and intrapelurally through surgery in the pleurisy test. In the λ-carrageenan-induced edema model, TPGS-stabilized curcumin nanoparticles were given orally one hour before induction and at 0.5, 4.5, and 8.5 h after induction with two different doses (1.8 and 0.9 mg/kg body weight (BW)). Sodium diclofenac with a dose of 4.5 mg/kg BW was used as a standard drug. A physical mixture of curcumin-TPGS was also used as a comparison with a higher dose of 60 mg/kg BW. The anti-inflammatory effect was assessed on the edema in the carrageenan-induced paw edema model and by the volume of exudate as well as the number of leukocytes reduced in the pleurisy test. TPGS-stabilized curcumin nanoparticles with lower doses showed better anti-inflammatory effects, indicating the greater absorption capability through the gastrointestinal tract.

CBCT significantly impacts dental procedures and has brought significant reforms in our approach to diagnosis & treatment planning despite its limitations in differentiating soft tissues. It is an excellent imaging modality and quickly identifies sinus opacification and provides valuable in-sight into paranasal sinus pathologies with considerably lower radiation exposure. The present study aimed to investigate the occurrence of maxillary sinus abnormalities in CBCT scans, identify the frequency, type, and location of these findings, and find the correlation between the distance of periapical lesions and radiographic changes in the maxillary sinus. Two examiners independently evaluated 117 patients to diagnose and classify the cases into different abnormality subtypes. The periapical lesions most closely related to the sinus were recorded. The diameters of the left and right maxillary sinus ostium and the distance of the ostium's lower border to the sinus's osseous floor were recorded. The findings were correlated with the age and gender of these patients. The present study revealed that sixty-one patients were diagnosed with mucosal thickening (52.1%). The sinus wall most affected by mucosal thickening was the maxillary sinus floor, followed by the medial and lateral walls. Of 19 patients with periapical lesions, 15 had maxillary sinus mucosal thickening and was statistically significant (p=0.004). The high occurrence of abnormalities in the maxillary sinus emphasizes the importance for the radiologist to comprehensively interpret the whole volume acquired in CBCT images, including the entire sinus. Incidental findings may be considered in the individual clinical context of signs and symptoms, reducing the risk of overes-timating the real impact of radiographic findings.

Debris-flows are recurrent events on mountain- and hill- slopes, and they have been the object of numerous field investigations and sampling, however most of this work reposes on imagery and outcrop analysis, in such a way that there are still only a handful of studies investigating the internal architecture of these events’ deposits. In the present contribution, we aims at underneath the internal structure of a portion of a debris-flow deposit that was accessible in the aftermath of the 2018 heavy-rainfall debris-flows in Hiroshima Japan. Using a Ramac Pro-Ex GPR with 500 MHz and 800 MHz antenna, a set of longitudinal and transversal transects was used to characterize the deposit. The results demonstrated that a set of subhorizontal layers have filled the valley, and interacting with local terrace edges, these layers have piled up and overcome the obstacle. Across the valleys, a set of trough suggest the presence of channels that were also filled during the event. Finally, in the channel post-event, a set of radargram “cross-bedded units” shows that the final deposition in the channel was of a more dilute flow, typical of a Newtonian flow. This set of units was not to be found at the surface of the post-event pseudo-surface, suggesting that the flow ended as a debris-flow on this surface, and that it is only when the flow dug the final channel that the nature of the flow returned from debris-flow to Newtonian flow.

Coronavirus 2019 (COVID-19) is an infectious disease that is becoming a pandemic. Hydroxychloroquine in combination with azythromycin are among drugs currently in use to eradicate COVID-19. Despite concerns due to its potential cardiac toxicity, hydroxychloroquine is widely accepted in mild and moderate COVID-19 pneumonia. In this case report, we report a case of a young Indonesian adult male with suspected COVID-19 pneumonia who received hydroxychloroquine and azythromycin therapies and during 24 hour experienced deterioration of atrioventricular block.

Integrated ultra-low-loss waveguides are highly desired for integrated photonics to enable applications that require long delay lines, high-Q resonators, narrow filters, etc. Here we present an ultra-low-loss silicon waveguide on 500 nm thick SOI platform. Meter-scale delay lines, million-Q resonators and tens of picometer bandwidth grating filters are experimentally demonstrated. We design a low-loss low-reflection taper to seamlessly integrate the ultra-low-loss waveguide with standard heterogeneous Si/III-V integrated photonics platform to allow realization of high-performance photonic devices such as ultra-low-noise lasers and optical gyroscopes.

Understanding microbial composition in upper respiratory infections (URIs) is critical for effective diagnosis and treatment. Precision Metagenomic next-generation sequencing p(mNGS) can provide a comprehensive yet clinically relevant profile of respiratory infection. The hybridization capture-based targeted sequencing generated a precision metagenomics profile of 29 patients with acute URIs. Nasopharyngeal samples were collected from the subjects suspected of respiratory infection, and p(mNGS) was performed using the Illumina®/IDbyDNA Respiratory Pathogen ID/AMR Panel (RPIP). The dataset obtained from the mNGS analysis contains a wealth of information on the composition of acute URI microbiota, including the relative abundance of known pathogens and potential clinical implications. The dataset represents a valuable resource for future research endeavors in respiratory medicine, infectious disease epidemiology, and therapeutic interventions. In addition, the dataset offers significant potential for reuse and integration with other omics datasets. The comprehensive nature of the mNGS data allows the exploration of associations between the respiratory microbiota and host factors such as clinical outcomes, immune responses, or genetic predisposition. Combining this dataset with other relevant datasets, such as transcriptomics or metabolomics, could provide a deeper understanding of the complex interactions between the microbiota and the host in acute URIs.

Arjunolic acid (AA) is a triterpenoid saponin majorly found in the Terminalia arjuna and is claimed to exert the cardiovascular protective effects as a phytomedicine. However, it is unclear how AA exerts the effects at the molecular level. Hence, this study used an in vitro model using lipopolysaccharide (LPS)-stimulated H9C2 and C2C12 myotubes to investigate the cardioprotective effects of arjunolic acid (AA) via MyD88-dependant TLR4 downstream signaling markers expression. The myotubes were developed by differentiating rat H9C2 and mouse C2C12 myoblast cells. The MTT viability assay was used to assess the cytotoxicity of AA. LPS induced in vitro cardiovascular disease model was developed in H9C2 and C2C12 myotubes. The treatment groups were designed such as control (untreated), LPS control, positive control (LPS+ pyrrolidine dithiocarbamate (PDTC)-25 µM), and treatment groups were co-treated with LPS and three doses of AA (50, 75, and 100 µM). The changes in the expression of TLR4 downstream signaling markers were evaluated through High Content Screening (HCS) and Western Blot (WB) analysis. The outcomes demonstrated that the expression of MyD88, MAPK, JNK, and NFκB markers were significantly upregulated in the LPS-treated groups compared to the untreated control. Evidently, the HCS analysis revealed that MyD88, NF-κB, p38, and JNK were significantly downregulated in the H9C2 myotube in the AA treated groups (50, 75, and 100 µM). For, the C2C12 myotube, the expression of NFκB was downregulated. TLR4 marker expression in H9C2 and C2C12 myotubes was subsequently decreased by AA treatment, suggesting possible cardioprotective effects of AA.

Exudative-pleural-effusion (ePE) is a common presentation in pulmonology clinics. Pleural biopsy is indicated for identifying the aetiology in undiagnosed ePE especially the ones with low adenosine-deaminase levels. The access to rigid and semi-rigid medical thoracoscopy is scarce and heterogeneous in a resource limited country like India. In such circumstances, using flexible bronchoscope via intercostal-chest-tube for visualization of parietal pleura and pleural biopsy offers a way out. Here, in this retrospective study, we have presented our experience of such practice on 25 cases. Mean age was 52.4±1 years. Adhesions were present in 40% of the subjects. Most common finding was presence of nodules. On an average 6.8 passes were taken with maximum of 10. In 32% cases only tiny tissue was obtained, hence requiring multiple passes. Large tissue could be obtained in 44% of the subjects. Mean duration of the procedure was 35.6±9.0 minutes. Tissue diagnosis was established in 80% with most common being malignancy (48%) followed by tuberculosis (20%). In 3 cases, the final diagnosis was made by exclusion. No major complications were recorded. In conclusion, medical thoracoscopy using flexible video bronchoscope via intercostal-chest-tube was a feasible alternative for the diagnosis of ePE effusion in resource limited settings.

Postharvest physiological deterioration (PPD) of fresh cassava roots limits its shelf-life to about 48 hours. There is a demand for simple, cheap, and logistically feasible solutions for extending the shelf life of fresh cassava roots at industrial processes. In this study, three different types of bag materials were tested (woven polypropylene, tarpaulin, and jute as a potential storage solution for cassava roots with different levels of mechanical damages. Microclimate (temperature, humidity, CO2) was monitored to understand the storage conditions for up to 12 days. The results showed that fresh cassava roots could be stored for 8 days, with minimal PPD and starch loss (2.4 %). How-ever, roots with significant mechanical damage (cuts, breakages) had a considerably shorter shelf life in the storage bag, compare to whole roots and roots with retained peduncle (stalk where roots are connected to the main plant). Wetting the roots and type of bag material were not significant factors in determining the shelf life and starch loss. Carbon dioxide concentration in the stores significantly correlated with the starch loss in fresh cassava roots and is proposed as a possible method for continuously and remotely monitoring starch loss in large scale commercial operations and reduce postharvest losses.

Background. Coronary artery disease (CAD) with extensive stenosis presents significant clinical challenges. This case report details the management and outcomes of a 61-year-old male with a notable history of CAD, initially treated with coronary artery bypass grafting (CABG), followed by an innovative intravenous hydrogen and oxygen nanobubble therapy due to recurrent symptoms.Case Presentation. Mr. BH was diagnosed with significant stenosis in the left anterior descending (LAD) artery and left circumflex (LCx) artery, initially managed by CABG. Recurring symptoms led to the adoption of a novel treatment involving hydrogen and oxygen nanobubbles. Following treatment initiation, Mr. BH experienced substantial improvements in physical capacity and symptomatic relief, with an ability to climb 22 flights of stairs and resolution of previous symptoms such as dyspnea and cough. Despite these improvements, subsequent imaging revealed in-stent restenosis and progression of graft disease.Discussion. The application of hydrogen and oxygen nanobubbles as a therapy in CAD is explored, highlighting potential mechanisms such as reduction of oxidative stress and improvement in endothelial function. This case contrasts the effects of conventional surgical and pharmaceutical interventions with the novel nanobubble therapy, illustrating both the benefits and complexities of managing advanced CAD with innovative treatments.Conclusion. While Mr. BH showed clinical improvement with nanobubble therapy, the development of new severe stenosis and restenosis underscores the need for further research to understand the long-term efficacy and mechanisms of nanobubble therapy in complex CAD cases. This case suggests that while innovative therapies may provide symptomatic relief and functional improvement, they do not obviate the need for ongoing surveillance and possibly further intervention.

Development of the self-cleaning and anti-fogging superhydrophobic coating for aluminum surfaces which is durable in the aggressive conditions has raised tremendous interest in materials science. In this work, by employing chemical etching technique with mixture of hydrochloric and nitric acid, followed by passivation with lauric acid, superhydrophobic aluminum surface was synthesized. The surface morphology analysis reveals the presence of rough microstructures on coated aluminium surface. Superhydrophobicity with water contact angle of 170 ± 3.9° and sliding angle of 4 ± 0.5° is achieved. Surface bounces off the high speed water jet, indicating excellent water-repellent nature of coating. It is also continuously floated on water surface for several weeks, showing excellent buoyancy nature. Additionally, coating maintains its superhydrophobicity after undergoing 100 cycles of adhesive tape peeling test. Its superhydrophobic nature withstands 90° and 180° bending, and repeated folding and de-folding. Coating exhibits the excellent self-cleaning property. In low temperature condensation test, almost no accumulation of water drops on the surface, showing the excellent anti-fogging property of coating. This approach can be applied to any size and shape of aluminium surface and hence has great industrial applications.

Modeling what makes an advertisement persuasive, i.e., eliciting the desired response from consumer, is critical to the study of propaganda, social psychology, and marketing. Despite its importance, computational modeling of per- suasion in computer vision is still in its infancy, primarily due to the lack of benchmark datasets that can provide persuasion-strategy labels associated with ads. Motivated by persuasion literature in social psychology and marketing, we introduce an extensive vocabulary of persuasion strategies and build the first ad image corpus annotated with persuasion strategies. We then formulate the task of persuasion strategy prediction with multi-modal learning, where we design a multi-task attention fusion model that can leverage other ad-understanding tasks to predict persuasion strategies. Further, we conduct a real-world case study on 1600 advertising campaigns of 30 Fortune-500 companies where we use our model’s predictions to analyze which strategies work with different demographics (age and gender). The dataset also provides image segmentation masks, which labels persuasion strategies in the corresponding ad images on the test split. We publicly release our code and dataset: https://midas-research.github.io/persuasion-advertisements/

This study investigates multiple extrusion regimens with twin screw extruder for valorising soy press cakes (by-products of soy drink & tofu manufacturing process) by varying physical conditions of extrusion (temperature and moisture content) for improving their morphological, physico-chemical, technological, and sensory parameters. Valorised soy press cakes were compared before and after extrusion. Four extrusion regimens (moisture content 30%-60% and temperature 110°C -120°C) were designed for producing different extruded samples. Small amounts (3%-6%) of untreated and extruded press cakes were utilised in the development of meat analogues. All samples showed comparable nutritional and trypsin inhibition activity with almost all samples possessing most essential amino acids above significant amounts. Press cakes with higher moisture indicated improved bulk density, water holding and oil holding capacity. Interestingly, the same samples also reportedly had texture more closely resembling native meat texture and scored the highest in overall sensory acceptance. Our results thus indicate that soy press cake samples from drink manufacturing process, when extruded with the regimen with 60% moisture and temperature of 120°C show the greatest potential in developing meat analogues.

The genus Vigna is penta-tropical having more than 200 species with many desirable economically important traits. The aim of study was to validate the in-silico polymorphism of whole genome sequence developed mungbean specific SSR markers and their transferability among the different Vigna species. The present study utilized a set of 200 SSR markers developed from whole genome sequence of mungbean and validated using a diversity panel of 25 accessions which belongs to 13 Vigna species. Out of 200 SSR markers, 130 markers (65%) were polymorphic across the various Vigna species and the number of alleles amplified varied between 7 to24. The SSR markers showed more than 90 percent transferability across the different Vigna species accessions. Based on allelic data, the 25 Vigna accessions grouped into three clusters based upon the unweighted pair group method with arithmetic mean (UPGMA) phylogenetic tree. The principal co-ordinates analysis (PCA) biplot graph and UPGMA based neighbor joining clustering diagram showed similar pattern of Vigna accessions distribution. The population structure assessment has grouped the cultivated and wild species accessions into two sub-population. The estimated marker parameters such as polymorphic information content (0.09 – 0.84), marker index (0.091 – 3.342) and effective multiplex ratio (1.0 – 4.0) suggested their adequacy in several genetic studies such as parental selection, hybrid testing, genetic mapping and marker aided breeding programmes for genetic enhancement of species belonging to the Vigna genus.

Background. Chronic kidney disease (CKD) is a progressive condition with limited treatment options that often lead to significant morbidity. Recent studies suggest that oxyhydrogen nanobubbles (HHOnb) may offer therapeutic benefits due to their antioxidative and anti-inflammatory properties. This case series examines the effects of intravenous HHOnb therapy on three patients with varying stages of CKD.Methods. Three patients with CKD underwent a series of ten HHOnb infusions over a period of two to three months. The patients, aged 43 to 70, presented with additional comorbidities including hypertension, diabetes mellitus, and polycystic kidney disease. Clinical parameters, including glomerular filtration rate (GFR), serum creatinine, blood pressure, and uric acid levels, were monitored alongside subjective health improvements.Results. Patient A. A 70-year-old woman with CKD grade 3a experienced a reduction in serum creatinine from 0.98 mg/dL to 0.82 mg/dL and an improvement in GFR from 59 mL/min/1.73 m² to 73.2 mL/min/1.73 m². She reported reduced leg swelling and increased vitality. Patient B. A 52-year-old man with CKD grade 4 and class III obesity showed a decrease in serum creatinine from 3.0 mg/dL to 2.86 mg/dL, an increase in GFR from 23 mL/min/1.73 m² to 24.4 mL/min/1.73 m², and improved sleep quality. Blood pressure reduced from 167/82 mmHg to 145/85 mmHg. Patient C. A 43-year-old man with CKD grade 4 and massive polycystic kidney disease reported reduced fatigue and normalized urination. His serum creatinine decreased from 3.26 mg/dL to 3.09 mg/dL, and his GFR improved from 22 mL/min/1.73 m² to 23.6 mL/min/1.73 m².Conclusion. Intravenous HHOnb therapy demonstrated potential benefits in improving renal function and overall health in CKD patients. These findings suggest that HHOnb could be a promising complementary treatment for CKD, though larger, controlled studies are needed to confirm its efficacy and safety.

A scientific consensus is emerging on the benefits of dc distribution in medium voltage power systems of ships and cities. At least 50% space savings and increased power transfer capacity are estimated with enhanced voltage dc operation of electric cables. The goal of this research is to contribute to developing the empirical knowledge on the insulation performance in order to validate the feasibility of such anticipated gains of dc versus ac, and to determine the comparative impact of different operational conditions from a component engineering point of view. The partial discharge (PD) activity in cables is measured under ac and dc conditions as an indicator of insulation performance. Specifically, PDs in defects at the semicon-insulation interface are studied in terms of inception voltage, repetition rate and discharge magnitude. Empirical understanding is drawn for operating voltage and frequency dependence of the discharge behavior in such voids in the range of 10 to 20\,kV and 0 to 0.1\,Hz, respectively. The change in PD activity with void evolution is explored.

Implementation of waterflood is with injected pressured water to reservoir to escalation oil production. Produced water is the dominated result from oil and gas mechanism in this world meanwhile 65% of water is injected back to the well for pressure maintenance, 30% for discharge aquifier condition and surface. For shaly sand, produced water usually bring coarse and suspended sand to the surface. Therefore, this sand level is needed to declining to avoid plugging in injection well until certain economic condition.

Background: Digital clinical measures collected via various digital sensing technologies such as smartphones, smartwatches, wearables, ingestible, and implantable are increasingly used by individuals and clinicians to capture health outcomes or behavioral and physiological characteristics of individuals. Time series classification (TSC) is very commonly used in modeling digital clinical measures. While deep learning models for TSC are very common and powerful, there exist some fundamental challenges. This review presents non-deep learning models commonly used for time series classification in biomedical applications that achieve high performance. Objective: We performed a systematic review to characterize the techniques used in time series classification of digital clinical measures throughout all stages of data processing and model building. Methods: We conducted a literature search on PubMed, and the Institute of Electrical and Electronics Engineers (IEEE), Web of Science, and SCOPUS databases using a range of search terms to retrieve peer-reviewed articles reporting academic research on digital clinical measures in the five year period between June 2016 and June 2021. We identified and categorized research studies based on the types of classification algorithms and sensor input types. Results: We found 452 papers in total from four different databases: PubMed, IEEE, Web of Science Database, and SCOPUS. After removing duplicates and irrelevant papers, 135 articles remained for detailed review and data extraction. Among these, engineered features using time series methods that were subsequently fed into widely-used machine learning classifiers was the most commonly used technique and also most frequently achieved the best performance metrics (77 out of 135 articles). Statistical modeling (24 out of 135 articles) algorithms were the second most common and also second best classification technique. Wavelet-based classification models (8 out of 135 articles) were also common. Electroencephalogram (29 out of 135 articles) was the most common data type used as an input. Accuracy was the most commonly reported performance metric, with 67.65% of articles reporting on accuracy. In this review paper, we provide summaries of signal pre-processing methods, feature engineering and selection methods, time series models, as well as model interpretations. Importantly, we found that about 50% of the papers only report one performance metric, which may result in a skewed view of overall performance. Conclusion: While high time series classification performance has been achieved in digital clinical, physiological, or biomedical measures, no standard benchmark datasets, modeling methods, or reporting methodology exist. There is no single widely used method for time series model development or feature interpretation– many different methods have proven successful.

The disruption of conventional manufacturing, supply, and distribution channels for medical supplies during the COVID-19 pandemic has caused widespread shortages and catalyzed local efforts to use nontraditional, rapid manufacturing to meet urgent healthcare needs. Here we present a crisis-responsive design framework designed to assist with product development under pandemic conditions. The framework utilizes extensive stakeholder engagement, comprehensive and dynamic needs assessment, local manufacturing, and product testing for the accelerated development of healthcare products. We contrast this framework with traditional medical device manufacturing and discuss relevant regulatory policies. We highlight the applicability of the crisis-responsive framework to a successful local program that designed and supplied face shields for a large US academic hospital. Finally, we make recommendations aimed at improving future resilience to healthcare emergencies. These include continued development of open source designs suitable for rapid manufacturing and changes in regulatory policy that strike a balance between rigidity and uncontrolled innovation.

Milk serves as a crucial source of natural bioactive compounds essential for human nutrition and health. The gastrointestinal digestion of milk proteins releases various biologically active peptides that positively impact human health and enhance physiological performance. With the growing production of cheese, Greek yogurt, and other dairy products, the volume of unutilized acid whey is significantly increasing. Acid whey, containing almost all whey proteins and approximately one-quarter of casein, presents a valuable raw material for generating peptides with potential health benefits. These peptides exhibit properties such as antioxidant, antimicrobial, anti-inflammatory, anticarcinogenic, antihypertensive, antithrombotic, opioid, mineral-binding, and growth-stimulating activities, contributing to improved human immunity and the treatment of chronic diseases. Enzymatic hydrolysis of milk proteins has been developed as a method to produce these peptides, facilitating their use in food fortification. To incorporate whey into functional beverages, it undergoes fermentation by lactic acid bacteria with proteolytic activity. To specifically enrich these beverages with peptides exhibiting targeted bioactivities, it is essential to select lactic acid bacteria strains possessing the requisite protease profiles. Additionally, the sensory properties of the final product can be enhanced using starter cultures with diverse metabolic capabilities, even in the absence of added flavoring agents. Given the imperative to develop waste-free technologies and enhance the profitability of the dairy industry, there is a growing need to efficiently utilize and transform acid whey into a broad spectrum of valuable products and food additives. This approach is justified not only by the nutritional benefits of the bioactive components in whey but also by the commercial potential of safe and health-enhancing products.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

In order to shorten the detection time and improve the average precision on embedded devices, A lightweight and high accuracy model is proposed for passion fruit in complex environments (backlight, occlusion, overlap, sunny, cloudy, rainy). Firstly, replacing the backbone network of YOLOv5 with a lightweight GhostNet model reduces the number of parameters and computation while improving detection speed. Secondly, a new feature branch is added to the GhostNet network, and the feature fusion layer in the neck network is reconstructed to effectively combine the lower-level and higher-level features, which not only improves the accuracy of the model but also maintains its lightweight. Finally, the knowledge distillation methods are used to transfer the knowledge from the more capable teacher model to the less capable student model, which significantly improving the detection accuracy. The improved model is denoted as G-YOLO-NK. The average accuracy of the G-YOLO-NK network is 96.00%, which is 1.00% higher than the original YOLOv5s model. Furthermore, the improved model size is 7.14MB, reduced to half of the original model, and the real-time detection frame rate is 11.25 FPS on the Jetson Nano. Compared to the state-of-the-art model, the proposed model outperforms them in terms of average precision and detection performance. The present work provides an effective model for real-time detection of passion fruits in complex orchard scenes, which can provide valuable technical support for the development of orchard picking robots and greatly improve the intelligence level of orchards.

The Simultaneous Localization And Mapping (SLAM) scanner is an easy and portable Light Detection And Ranging (LiDAR) data acquisition device. Its main output is a 3D point cloud covering the scanned scene. Regarding the importance of accuracy in the survey domain, this paper aims to assess the accuracy of two SLAM scanners: the NavVis VLX and the BLK2GO Scanner. This assessment is conducted for both outdoor and indoor environments. In this context, two types of reference data are used: the Total Station (TS) and the static scanner Z+F Imager 5016. To carry out the assessment, four comparisons are tested: cloud to cloud, cloud to mesh, mesh to mesh, and edge detection board assessment. However, the results of the assessments confirm that the accuracy of indoor SLAM scanner measurements (5 mm) is greater than that of outdoor ones (between 10 mm and 60 mm). Moreover, the comparison of cloud to cloud provides the best accuracy regarding direct accuracy measurement without manipulations. Finally, based on the high accuracy, scanning speed, flexibility, and the accuracy differences between tested cases, it is confirmed that SLAM scanners are effective tools for data acquisition.

The impact of interaction SS with MJO on rainfall along Java Island to East Nusa Tenggara has been studied using daily rainfall observation data from 2140 weather observation stations, which are also equipped with GSMaP, OLR, and ERA5 data. There were 61 SS events found, 17 during active MJO and 44 in inactive MJO. Rainfall increases more in the western study area when the active MJO and more in the eastern study area when the inactive MJO is due to SS. SS reduces rainfall in the Jakarta region, regardless of the activity or inactivity of the MJO. SS causes extreme rainfall to only occur in a small part of certain areas, so it tends to significantly reduce the possibility of extreme rainfall. In the southern part of the IMC, SS predominates over MJO in supporting increased water vapor transport. Large-scale synoptic circulations like the monsoon, SS, and MJO can interact with local land-sea wind circulation to produce spatiotemporal variability in rainfall on Java Island. Rainfall mostly increases in the afternoon and decreases in the morning when SS occurs, whether there is MJO or not. Convective instability analysis indicates that SS increases precipitation, most likely by lowering CIN and raising VIMFC.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

Superior fiber quality is one of the most important objectives in cotton breeding. To detect the genetic basis underlying fiber quality, an F2 population containing 413 plants was constructed by crossing Jifeng 914 and Jifeng 173, both of which have superior fiber quality, with Jifeng 173 being better. Five fiber quality traits were investigated in the F2, F2:3, F2:4, and F2:5 populations. Quantitative trait loci (QTL) mapping was conducted based on a high-density genetic map containing 11,488 single nucleotide polymorphisms (SNPs) and spanning 4,202.12 cM in length. Transgressive segregation patterns and complex correlations in the five tested traits were observed. A total of 108 QTLs were found, including 27 for fiber length (FL), 16 for fiber strength (FS), 24 for micronaire (MC), 17 for fiber uniformity (FU), and 24 for fiber elongation rate (FE). Chromosome A7 contained 12 QTL, ranking the first. No QTL was found on chromosome D1 and D11. Each QTL contributed 1.98%–21.45% to the phenotypic variation (PV), including 13 major effect QTLs that contributed more than 10% toward PV. Two QTLs could be repeatedly detected in three populations, including qFL-D3-2 in F2, F2:4, and F2:5 with 9.18%–21.45% of PV, qFS-A11-1 in F2:3, F2:4 and F2:5 with 6.05%–10.41% of PV. Another seven stable QTLs could be detected in two populations, including four major effect QTLs: qFL-A12-3, qFS-D10-2, qMC-D6-2, and qMC-D8-1. Fourteen QTL-overlapping regions were found, which might explain the complex correlations among the five phenotypic traits. Four regions on chromosome A11, D3, D6, and D10 covered by both stable and major effect QTLs are promising for further fine mapping. The genomic regions of the two QTLs detected in three populations and the four major effect QTLs contain 810 genes. Gene functional analysis revealed that the annotated genes are mainly involved in protein binding and metabolic pathways. Fifteen candidate genes in the qFL-D3-2 region are highly expressed in fiber or ovules during fiber initiation, elongation, secondary cell wall thickening, or maturation stages. qRT-PCR revealed that Ghir_D03G005440.1 and Ghir_D03G011310.1 may play a role in promoting fiber initiation, Ghir_D03G006470.1 may be beneficial for promoting fiber elongation. This study provides more information for revealing the molecular genetic basis underlying cotton fiber quality.

Currently there are fewer depth models applied to pepper picking detection, while the existing generalized neural networks have problems such as large model parameters, long training time, and low model accuracy.In order to solve the above problems, this paper proposes a Yolo-chili target detection algorithm for chili pepper detection. First, the classical target detection algorithm yolov5 is used as a benchmark model, and an adaptive spatial feature pyramid structure combining the attention mechanism and the idea of multi-scale prediction is introduced to improve the model's detection effect on occluded peppers and small target peppers. Secondly, a three-channel attention mechanism module is introduced to improve the algorithm's long-distance recognition ability and reduce the interference of redundant testers. Finally, the quantized pruning method is used to reduce the model parameters and realize the lightweight processing of the model. Applying the method to the homemade chili pepper dataset, the AP value of chili pepper reaches 93.11%; the accuracy rate is 93.51% and the recall rate is 92.55%.The experimental results show that yolo-chili is able to achieve accurate and real-time pepper detection under complex orchards.

The temporary immersion system bioreactor named GreenTray®[2], [3]presents advantages over the existing ones. Firstly, there is no need to use forceps to move the shoots or plantlets in or out of the recipient, neither the use of scalpel to divide them. Secondly, the basis of the shoot can remain in the GreenTray® and can sprout again in several cycles of growth. These two characteristics reduce the costs in the process of micropropagation. Besides, shoots or plantlets development is enhanced by the aeration of the recipient, thus enriching with CO2 the recipient atmosphere. The chapter describes and provides images and values of interest in (1) the micropropagation process of some commercial Prunus or Pyrus rootstocks; (2) the plantlet growth under autotrophic conditions; and (2) the inoculation of plants with pathogens that reproduce in vitro the symptoms observed in vivo, using the GreenTray® bioreactor.

Aiming at the problems of inaccurate segmentation of long object and information loss of small object in real-time semantic segmentation algorithm, this paper proposes a lightweight multi-branch real-time semantic segmentation network based on BiseNetV2. The new auxiliary branch makes full use of spatial details and context information to cover the long object in the field of view. Meanwhile, in order to ensure the inference speed of the model, the asymmetric convolution is used in each stage of the auxiliary branch to design a structure with low computational complexity. In the multi-branch fusion stage, the alignment and fusion module is designed to provide guidance information for deep and shallow feature mapping, so as to make up for the problem of feature misalignment in the fusion of information at different scales, and thus reduce the loss of small target information. In order to further improve the model’s awareness of key information, a global context module is designed to capture the most important features in the input data. The proposed network uses NVIDIA GeForce RTX 3080 Laptop GPU experiment, on the road street view data set Cityscapes and CamVid average occurring simultaneously ratio reached 77.1% and 78.4% respectively, with running speed of 127 frames/s respectively and 112 frames/s. The experimental results show that the proposed algorithm can achieve real-time segmentation and improve the accuracy significantly, showing good semantic segmentation performance

In this paper we study a class of impulsive delayed neural networks with parameter uncertainties and reaction-diffusion terms. Using the properties of M-matrices and some inequality techniques, some sufficient conditions are derived to guarantee the global exponential stability of the given system. The results obtained are presented by simple algebraic inequalities, which are certainly more concise than previous methods. Finally, the validity and usefulness of our results are illustrated by arithmetic examples.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

Pyrops candelaria is one of the common pests of fruit trees, but the research on the pathogenic microorganisms it may carry is very limited. Therefore, it is essential to reveal the pathogenic microbes it carries and their potential hazards. This study found a new virus from the transcriptome of P. candelaria, which was first reported in P. candelaria and named as PyCaV (Pyrops candelaria associated virus). RACE and bioinformatics assay revealed that the full-length of PyCaV is 10855 bp with the polyA tail, containing a single open reading frame (ORF) encoding a polyprotein consisting of 3171 amino acid (aa). The virus has a typical Iflavirus structure, including two rhv domains, a RNA helicase domain (HEL), a 3C cysteine protease domain (Pro), and a RNA-dependent RNA polymerase domain (RdRp). Further phylogenetic analysis revealed that this virus belongs to family Iflaviridae and sequence alignements analysis suggedted PyCaV is new member in unassigned genus of family Iflaviridae. Further in-depth analysis of virus-infection-part showed that PyCaV is distributing in the whole longan lanternfly, including its head, chest, and abdomen, but more PyCaV was identified in the chest. The distribution of PyCaV in different parts of P. candelaria was further explored, which showed that more PyCaV were detected in its piercing-sucking mouthparts and chest viscera. Statistical analysis showed that the PyCaV infection was affected by time and locations.

With the burgeoning growth of online retail, the issue of counterfeit products has become a significant threat to both consumer trust and brand integrity, posing challenges to sustainable market practices. Online retail platforms are promoted to redesign their channel structures and enhance brand traceability to tackle counterfeits using blockchain technology. To investigate the interactions between blockchain technology and the channel structures of online retail platforms, we design a game theory model incorporating a manufacturer with(out) blockchain participation selling products via an online retail platform that operates an agency channel and/or a reselling channel. We show that the critical trade-off of blockchain participation comprises the brand assurance effect of the blockchain, the channel competition intensification effect, and the blockchain adoption cost. The platform is capable of strategically designing the channel structure to encourage (while discouraging) blockchain participation by the manufacturer. Our analysis highlights the complementarity between blockchain participation and the channel structure. Furthermore, the effect of the consumer’s belief in the reselling channel, the commission fee in the agency channel, and the substitutability between channels are investigated in depth. The research provides valuable insights for online retail platforms and policymakers seeking to foster a sustainable and trustworthy e-commerce ecosystem.

Apis mellifera, especially weak ones, are highly vulnerable to Carpoglyphus lactis mites, which can rapidly infest and consume stored pollen, leading to weakened colonies and potentially colony collapse. This study aimed to ascertain and investigate the prevalence of this mite in honeybee colonies across 9 provinces in the Republic of Korea (ROK). A total of 615 honeybee colonies were collected, from 66 apiaries during the spring and 58 apiaries during the summer of 2023. A 1,242 bp segment of the the Cytochrome c oxidase subunit 1 (COI) gene was amplified using the polymerase chain reaction method. The detection levels of C. lactis in the honeybees were compared between winter and summer. Based on the COI sequence analysis, the nucleotide sequence similarity of C. lactis mites isolated in the ROK with those from China (NC048990.1) was found to be 99.5%, and with those from the United Kingdom (KY922482.1) was 99.3%. This study is the first report of C. lactis in Korean apiaries. The findings in this study demonstrate a significantly higher detection rate in winter, which is 4.1 times greater than that in summer (p &lt; 0.001). Furthermore, the results underscore the usefulness of molecular diagnostic techniques for detecting C. lactis mites.

COX II containing a dual core CuA active site is one of the three core subunits of mitochondrial Cco, which plays a significant role in the physiological process. In this report, the full-length cDNA of COXⅡ gene was cloned from Sitophilus zeamais, which had an ORF of 684 bp encoding 227 amino acids residues. The predicted COXⅡ protein had a molecular mass of 26.2 kDa with pI value of 6.37, and multiple sequence alignment and phylogenetic analysis indicated that Sitophilus zeamais COXⅡ had high sequence identity 78.51% with the COXⅡ of other insect species, especially similarity to sitophilus oryzae. This gene was subcloned into the prokaryotic expression vector pET-32a, and induced by IPTG in E.coli Transetta (DE3) expression system. Finally the COXⅡ with 6-His tag was purified using affinity chromatography with Ni²⁺-NTA agarose. WB showed the recombinant COXⅡ was about 44 kD, and the concentration of fusion protein was 50μg/mL. UV-spectrophotometer and infrared spectrometer analysis showed that recombinant COXⅡ could catalyze the oxidation of substrate Cytc, and influenced by AITC. It was found that AITC could form a hydrophobic region with COXⅡ protein via molecular docking, besides, a sulfur atom of AITC structure could form a length of 2.9 Å hydrogen bond with Leu-31. These results will provide valuable information for elucidating the role of COXⅡ in Sitophilus zeamais responses to AITC, meanwhile, it will helpful to carry out a point mutation in AITC binding sites for the future research.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

The paper describes the new method for image compression based on coordinated group signal transformation. The algorithm is a type of difference coding. Coordinated processing significantly simplifies the difference signal conversion scheme using a single group codec for all signals. The described method considers color channels as correlated signals of a multi-channel communication system. The specifics of the processed data required modification of the coordinated group processing algorithm. First, we changed how to calculate the difference signals to prevent data loss. Secondly, the group codec was supplemented with a neural network to improve the quality of reconstructed images. We considered the following types of neural networks: fully connected, recurrent, convolution, and convolution in the Fourier space. Based on the simulation results, it is best to use fully connected neural networks if the goal is to minimize processing delay time. These networks have a response time of 13 ms. On the other hand, if the priority is to improve quality in cases where delays are not critical, then convolution neural networks in the Fourier space should be used. These networks have a response time of 140 ms and are of significant interest.

As the world population grows, fulfilling the need for biomaterials in the healthcare system becomes increasingly important. Biomaterials, which include metals, polymers, ceramics, and composites, play an important role in the creation of medical devices that improve people's lives. The European Society for Biomaterials described biomaterials as non-biological materials used in medical devices to interact with biological systems. This definition has developed to encompass materials that treat, assess, or replace tissues or bodily functions. Biocompatibility, as defined by the FDA, is a key feature of biomaterials, as is the requirement to fulfil design requirements such as mechanical performance, geometry, and electrical control. Over the last decade, advances in regenerative medicine and tissue engineering have boosted biomaterials' usage in medical applications dramatically. Despite its promise, scientists, engineers, and physicians continue to face significant challenges due to the complexity of biomaterials. Biomaterials have various benefits, including biodegradability, non-toxicity, and biocompatibility, making them extremely useful for replacing, sustaining, or improving biological activities in damaged tissues. They are used in a wide range of applications, including tissue engineering implants, human tissue healing and regeneration, medication delivery systems, and biosensors. This study gives insights into the fundamental characteristics, case studies, and ethical issues associated with the usage and use of biomaterials, further examining their potential and significance in healthcare and medicine.

The studied solar pot is a recent invention, which gained a utility model protection in 2021 from the Hungarian Intellectual Property Office under patent number 5489. The device is made for environmentally friendly cooking or heating (by utilizing solar energy) of foods and liquids. Its structure is similar to a double pipe heat exchanger, it has an outer mantle and an inner cooking tank. The goals of the paper are proposing a new physically-based mathematical model describing the solar pot and carrying out computer experiments with it, assembling an experimental system of the pot connected with a solar collector and performing measurements on it. Based on the results, the solar pot can successfully be used for cooking or sterilizing foods or liquids during the studied time period, in Hungary.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

This paper is focused on typical rural settlements in the Stara Planina Mountain area in Serbia. They are distinguished by their authenticity, identity and character, and they have still not been destroyed by inappropriate development as is the case in some other mountain areas in Serbia, where the effects of urbanization, globalization and homogenization are obvious. Consequently, there is a need to prevent these effects in mountain areas where there is a threat of disbalance between development and the inherited natural and cultural values. The paper starts from several important concepts that relate contemporary approaches to cultural heritage preservation, place morphology and planning future development. The concept definitions from recent documents from related fields are used. These concepts are then applied to the area of Stara Planina Mountain and its rural settlements. The necessity for an integrative approach to planning this area with significant natural and anthropogenic potential is pointed out, including its integration into international programs of sustainable development.

Abstract: Transcription factors are crucial pre-transcriptional regulatory mechanisms that can modulate the expression of downstream genes by binding to their promoter regions. DOF (DNA binding with One Finger) proteins are a unique class of transcription factors with extensive roles in plant growth and development. Our previous research indicated a decrease in iron content in chlorotic bamboo leaves. However, to our knowledge, genes related to iron metabolism pathways in bamboo species have not yet been studied. Therefore, in the current study, we identified iron metabolism-related (IMR) genes in bamboo and determined the transcription factors that significantly influence them. Among these, DOFs were found to have widespread effects and potentially significant impacts on their expression. We identified specific DOF members in Dendrocalamus latiflorus with binding abilities through homology with Arabidopsis DOF proteins, and established connections between some of these members and IMR genes using RNA-seq data. Additionally, molecular docking confirmed the binding interactions between these DlDOFs and the DOF binding sites in the promoter regions of IMR genes. The co-expression relationship between the two gene sets was further validated using q-PCR experiments. This study paves the way for research into iron metabolism pathways in bamboo and lays the foundation for understanding the role of DOF transcription factors in D. latiflorus.

The wetlands in northeastern Bangladesh are home to some of the most prolific and valuable ecosystems on the planet, offering a wide range of benefits to both the local and wider communities. A limited number of research on this topic have been carried out in various wetlands in coastal hilsa, but none have been located in the northeastern region of Bangladesh. Thus, the goal of this study was to better understand the most commercially relevant species (anadromous hilsa) in northeastern Bangladesh as well as to assess the wetland ecosystem services more thoroughly with the contribution of their fish genetic resources. In addition to laboratory studies, fieldwork was done in the fishing settlements along the Surma River, Hakaluki Haor, and Tanguar Haor. The study classified 77 fish species into 21 subcategories of ecosystem services, of which 56% were not threatened, 17% were vulnerable, and 10% were highly endangered. The species Hilsa was found to be the most economically significant, accounting for 1% of the GDP overall. The study determined if the hilsa stock of the examined wetlands maintains a single or several subpopulations in comparison to other parts of the country when they migrate from saline water to northeastern Bangladesh (freshwater). But when compared to other groups, the FST score was between 0.000 to 0.017, indicating that the populations are identical and that there is genetic material sharing between them. Additionally, these statistics imply that the Sylhet haor and adjacent river systems contain a single stock of Hilsa fish. Nevertheless, a number of stresses and risks, including overexploitation, illicit and destructive fishing, siltation, and natural disasters like flash floods, have been linked to changes in the supply of hilsa and other ecosystem services. This study also emphasizes the necessity of policy attention and research to address the concerns.

Severe acute respiratory syndrome coronavirus type 2 (SARS-CoV-2) continues to be a global threat due to its ability to evolve and generate new subvariants, leading to new waves of infection. Additionally, other coronaviruses like Middle East respiratory syndrome coronavirus (MERS-CoV, formerly known as hCoV-EMC) which first emerged in 2012, persists and continues to present a threat of severe illness to humans. The continued identification of novel coronaviruses, coupled with the potential for genetic recombination between different strains, raises the possibility of new coronavirus clades of global concern emerging. As a result, there is a pressing need for pan-CoV therapeutic drugs and vaccines. After extensive optimization of an HCV protease inhibitor screening hit, a novel 3CLPro inhibitor (MK-7845) was discovered and subsequently profiled. MK-7845 exhibited nanomolar in vitro potency with broad spectrum activity against a panel of clinical SARS-CoV-2 subvariants and MERS-CoV. Furthermore, when administered orally, MK-7845 demonstrated a notable reduction of viral burdens by &gt;6 log orders in the lungs of transgenic mice infected with SARS-CoV-2 (K18-hACE2 mice) and MERS-CoV (K18-hDDP4 mice).

The continuous casting process of helical fiber reinforced metal matrix composites was proposed, and the experimental equipment was designed and manufactured. The relationship model be-tween the process parameters and the helical shape of the fibers in the metal matrix is analyzed by differential geometry. Helical carbon fiber reinforced lead matrix composites were prepared under different conditions. When the melting temperature and cooling intensity were increased, the helical radius of helical carbon fiber in lead matrix was increased. When the fiber rotation speed was increased, the helical radius was decreased, and the helical pitch was de-creased proportionally. The experimental results are consistent with the process model. Carbon fiber rein-forced aluminum composites were prepared. Scanning electron microscopy showed that the infiltration between the aluminum matrix and the carbon fiber was not complete. As the volume fraction of carbon fiber which was added in composites is too small, the mechanical properties of the composites have not been significantly improved.

This article presents an innovative approach to the design of a safe adaptive backstepping control system. Tailored specifically for underactuated marine robots, the system utilizes simple sensors for enhanced practicality and efficiency. Given their operation in diverse oceanic environments fraught with various sources of uncertainties, ensuring the system's safe and robust behavior holds paramount importance in the control literature. To address this concern, this paper introduces a control strategy designed to ensure robustness at both the kinematic and dynamic levels. By emphasizing the compensation for the system uncertainties, the design integrates a straightforward fuzzy system structure. To further ensure the system's safety, a funnel surface is defined, followed by the design of a suitable nonlinear sliding surface as a function of the funnel and tracking error. Specifically leveraging the Lyapunov function, the study formally establishes the Semi-globally Practically Finite-time Stability of the closed-loop system, validated through simulations conducted on underactuated marine robots.

Several types of guided bone regeneration materials are available with various properties and clinical indications. Among them, dentin-derived matrix from extracted teeth is an excellent alternative to traditional graft materials, such as allografts and xenografts. Different clinical preparation protocols exist: block form versus powder form, demineralized versus non-demineralized form. Out of these methods, demineralization protocols for dentin-derived matrix from extracted teeth have been noted for a wide range of successful clinical outcomes. The purpose of this animal study was to find out the most effective method of demineralizing dentin-derived matrix to result in the highest regenerative ability in the bone graft material in rabbit calvaria. The study conducted a comparative histomorphometric analysis of four groups in distinguished matrix conditions: a control group without graft placement, a non-demineralized dentin-derived matrix graft placement group, a 15-minute demineralized dentin-derived matrix graft placement group, and a 30-minute demineralized dentin-derived matrix graft placement group. Regenerative processes were evaluated three times at 2, 4, and 8 weeks post-graft placement. These groups of rabbits were evaluated randomly in a blinded setting to prevent bias. Among the four groups compared, the group with a 15-minute demineralized dentin-derived matrix graft showed the most efficient bone regeneration in the histomorphometric analysis. Based on this animal study, it was apparent that a 15-minute demineralization of dentin-derived matrix is the preferred preparation protocol to maximize the regenerative potential in the matrix.

Promoting green development has become an important way to optimize the ecological and economic structure and promote sustainable development. The Yangtze River Economic Belt is an important economic corridor in China, and it remains to be examined whether the implementation of environmental regulations has enhanced the green total factor productivity (GTFP) of cities. This paper calculates the green total factor productivity of 107 cities within the Yangtze River Economic Belt by using the super-efficient SBM model and the GML index with Chinese city panel data from 2007-2019 and measures the intensity of environmental regulations through textual analysis. The bidirectional fixed-effects model constructed in this paper suggests an inverted U-shaped relationship between environmental regulation and GTFP, which is confirmed by a series of robustness tests. Green technology innovation and advanced industrial structure play a mechanism role in this. In regions with lower levels of green technology and industrial structure, the inverted U-shaped relationship between environmental regulation and green total factor productivity is more significant. In addition, the phenomenon of GTFP rising and then falling because of environmental regulation is more obvious in cities in the middle and upper reaches of the Yangtze River and outside the urban agglomerations. Therefore, when formulating environmental regulation policies, it is necessary to balance the relationship between economic development and environmental protection and harmonize the environment and economic development of the entire Yangtze River Basin.

Cocoa (Theobroma Cacao, L.) represents an important market that gained relevance and became an esteemed commodity thanks to cocoa powder, chocolate, and other related products. This work has analyzed 59 cocoa powder samples from the European market. Three distinct subgroups were identified: organic or conventional, alkalized or not alkalized, and raw or roasted processing. The impact of the technological process was evaluated on the pH, color, and compositional traits, as content of biogenic amines and salsolinol. The phenolic fraction was also investigated trough both common and emerging methods. Results depict that the influence of the agronomical practices (organic/conventional) did not affect significatively (p&lt;0.05) the composition of cocoa powders; similarly, the roasting process was not discriminative for the compounds traced. On the other hand, the alkalinization process greatly impacted on color, and pH, no matter of cocoa provenience, obtention, or other processes, also resulting reducing the phenolic fraction of treated samples. Principal components analysis confirmed that the alkali process acts on pH, color, and phenolic composition, but not on other bioactives molecules (BAs and salsolinol). All samples resulted safe while alkalized powders have a great reduction in beneficial biocompounds. A novel strategy could be to emphasize non-alkalized powders in the label, to meet the demand for more beneficial products.

Oral squamous cell carcinoma (OSCC) is a highly prevalent and aggressive malignancy, with mortality rates that reach 60%, mainly due to an excessive diagnostic delay. MiRNAs, a class of crucial epigenetic gene-expression regulators, have emerged as potential diagnostic biomarkers, with >200 molecules reported to be dysregulated in OSCC. We had previously established an in silico methodology for the identification of the most disease-specific molecules by bridging genetics and epigenetics. Here, we identified the stage-specific miRNAs that govern the asymptomatic early stages of oral tumorigenesis by exploiting the reverse interplay between miRNA-levels and their target-genes’ expression. Incorporating gene expression data from our group’s experimental hamster model of sequential oral oncogenesis, we bioinformatically detected the miRNAs that simultaneously target/regulate >75% of the genes that are characteristically upregulated or downregulated in the consecutive stages of hyperplasia, dysplasia and early-invasion OSCC, while exhibiting the opposite expressional dysregulation in OSCC-derived tissue and/or saliva specimens. We found that all stages share the downregulation of miR-34a-5p, miR124-3p, and miR-125b-5p, while miR-1-3p is underexpressed in dysplasia and early-invasion. Malignant early-invasion stage is distinguished by the downregulation of miR-147a and the overexpression of miR-155-5p, miR-423-3p and miR-34a-5p. The identification of stage-specific miRNA molecules may facilitate their utilization as biomarkers for presymptomatic OSCC diagnosis.

Estimating the ocean’s subsurface thermohaline information from satellite measurements is essential for understanding ocean dynamics and El Niño phenomenon. This paper proposes an improved double-output Residual Neural Network (DO-ResNet) model to concurrently estimate the ocean subsurface temperature (OST) and ocean subsurface salinity (OSS) in the tropical Western Pacific using multi-source remote sensing data, including sea surface temperature (SST), sea surface salinity (SSS), sea surface height anomaly(SSHA), sea surface wind (SSW), and geographical information (including longitude (LON) and latitude (LAT)). In the model experiment, Argo data were used to train and validate the model, and the root mean square error (RMSE), normalized root mean square error (NRMSE) and coefficient of determination (R²) were employed to evaluate the model's performance. The results showed that the sea surface parameters selected in this study have a positive effect on the estimation process, and the average RMSE and R² values for estimating OST (OSS) by the proposed model are 0.34 °C (0.05 psu) and 0.91 (0.95), respectively. Under the data conditions considered in this study, DO-ResNet demonstrates superior performance relative to the extreme gradient boosting model, random forest model, and artificial neural network model. Additionally, this study evaluates the model’s accuracy by comparing its estimations of OST and OSS across different depths with Argo-derived data, demonstrating the model's ability to effectively capture the most spatial features, and by comparing NRMSE across different depths and seasons, the model displays strong seasonal adaptability. In conclusion, this research introduces a novel artificial intelligence technique for estimating OST and OSS in the tropical Western Pacific Ocean.

The normal growth and development of skeletal muscle is essential for the health of the body. The regulation of skeletal muscle by intestinal microorganisms and their metabolites has been continuously revealed. Acetate is the predominant short-chain fatty acid synthesized by gut microbiota through the fermentation of dietary fiber, however, the underlying molecular mechanisms governing the interaction between acetate and skeletal muscle during rapid growth stage remain to be further elucidated; Here, specific pathogen-free (SPF) mice, germ-free (GF) mice, and germ-free mice supplemented with sodium acetate (GS) were used to evaluate the effects of acetate on skeletal muscle growth and development of young mice with gut microbiota deficiency; We found the concentration of serum acetate, body mass gain, succinate dehydrogenase activity and expression of myogenesis maker gene of skeletal muscle in the GS group was higher than GF group following sodium acetate supplement. Furthermore, the transcriptome analysis revealed that acetate activated biological processes regulating skeletal muscle growth and development in GF group that are inhibited due to gut microbiota deficiency. In vitro experiment, we proved that acetate up-regulated Gm16062 to promote skeletal muscle cell differentiation; Overall, our findings proved that acetate promote skeletal muscle growth and development in young mice via increase Gm16062 expression.

Phased injection of natural gas into internal combustion marine engines is a promising solution for optimizing performance and reducing harmful emissions, particularly unburned methane, a potent greenhouse gas. This innovative practice distinguishes itself from continuous injection because it allows for more precise control of the combustion process with only a slight increase in system complexity. By synchronizing the injection of natural gas with the intake and exhaust valve opening and closing times while also considering the gas path in the manifolds, methane release into the atmosphere is significantly reduced, making a substantial contribution to efforts to address climate change. Moreover, phased injection improves the efficiency of marine engines, resulting in reduced overall fuel consumption, lower fuel costs, and increased ship autonomy. This technology has been tested on a single-cylinder, large-bore, four-stroke research engine designed for marine applications, operating in dual-fuel mode with diesel and natural gas. Performance was compared with that of the conventional continuous feeding method. Evaluation of the effect on equivalent CO2 emissions indicates a potential reduction of up to approximately 20%. This reduction effectively brings greenhouse gas emissions below those of the diesel baseline case, especially when injection control is combined with supercharging control to optimize the air-fuel ratio.

In numerical simulations, achieving high accuracy without significantly increasing computational costs is often challenging. To address this, this paper presents an improved finite volume weighted essentially non-oscillatory (WENO) scheme tailored for applicability in computational fluid dynamics (CFD) and implemented in the flow solver NUAA-Turbo for simulating turbomachinery flows using both RANS and RANS/LES coupling. Firstly, the new WENO scheme is validated against classic numerical test cases to assess its stability and reliability in handling discontinuities, the Double problem, and Raleigh-Taylor (RT) instability issues. Compared to the original format, this enhanced finite volume WENO scheme demonstrates superior stability near discontinuities and resolves flow features with the same grid resolution more effectively. Next, for engineering applications related to turbomachinery, such as compressor and turbine characteristics, computations are performed using RANS, and the results obtained using WENO-ZQ3 and WENO-JS3 are compared. Finally, the new fifth-order WENO scheme is applied to RANS/LES coupled simulations of turbine wakes and film cooling. The results show that the enhanced finite volume WENO scheme offers improved stability and accuracy in engineering applications, allowing for high-precision calculations with fewer grid points to capture more detailed flow physics, thereby reducing computational costs in aerodynamic applications.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

To secure logic circuits against the illegal copying the insertion of the so-called key bit inputs using XOR/XNOR gates has been proposed in . The inserted gates modify (lock) the behavior of the original circuit and only the correct choice of the secret key bits guarantees the equivalent behaviour of the locked circuit to the original circuit. To break this kind of security, i.e. to find the secret key bits, there was a SAT solver based attack proposed in . The aim of this work is to experimentally verify this attack on several locked circuits with various number of primary inputs and outputs and with various number of gates. Except for the random placement of the key gates we evaluate also the positioning with chaining elimination. The obtained and presented results show that we were able to unlock 10 of 11 circuits within few minutes on a common PC.

Intermetallic compounds are increasingly being expected to utilize in tribological environments, but to date the works are hindered by insufficient ductility at low and medium temperature. This paper presents a novel multiphase intermetallic alloy with the chemical composition of Mo-40Ni-13Si (at.%). Microstructure characterization reveals that a certain amount of ductile Mo phases formed during the solidification process of ternary Mo-Ni-Si alloy melt, which is undoubtedly beneficial to the ductility improvement of intermetallic alloy. Tribological properties of the designed alloy, including wear resistance, friction coefficient and metallic tribological compatibility, were evaluated under dry sliding wear test conditions at room temperature. Results suggested that the multiphase alloy possesses an excellent property for room-temperature wear applications, which is attributed to the unique microstructural features and thereby good combination in hardness and ductility. The corresponding wear mechanism is also reported by observing the worn surface, subsurface and wear debris of alloy, which to be found is soft abrasive wear.

With the integrated development of the Internet, wireless sensor technology, cloud computing, and mobile Internet, there has been a lot of attention given to research about and applications of the Internet of Things. A Wireless Sensor Network (WSN) is one of the important information technologies in the Internet of Things; it integrates multi-technology to detect and gather information in a network environment by mutual cooperation, using a variety of methods to process and analyze data, implement awareness, and perform tests. This paper mainly researches the localization algorithm of sensor nodes in a wireless sensor network. Firstly, a multi-granularity region partition is proposed to divide the location region. In the range-based method, the RSSI (Received Signal Strength indicator, RSSI) is used to estimate distance. The optimal RSSI value is computed by the Gaussian fitting method. Furthermore, a Voronoi diagram is characterized by the use of dividing region. Rach anchor node is regarded as the center of each region; the whole position region is divided into several regions and the sub-region of neighboring nodes is combined into triangles while the unknown node is locked in the ultimate area. Secondly, the multi-granularity regional division and Lagrange multiplier method are used to calculate the final coordinates. Because nodes are influenced by many factors in the practical application, two kinds of positioning methods are designed: the unknown node is in the positioning unit or not. When the unknown node is on the side of the positioning unit, we use the method of vector similarity. Moreover, we use the centroid algorithm to calculate the ultimate coordinates of unknown node. When the unknown node is not on the side of the positioning unit, we establish a Lagrange equation containing the constraint condition to calculate the first coordinates. Furthermore, we use the Taylor expansion formula to correct the coordinates of the unknown node. In addition, this localization method has been validated by establishing the real environment.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

This study aimed to identify whether gyrate atrophy of the choroid and retina (GACR) heterozygous individuals have possible clinical manifestations and to explore the potential pathogenic mechanism. In this retrospective study, we surveyed a two-generation pedigree of an individual diagnosed with GACR. Two family members underwent ophthalmological, hematologic, and genetic tests. An arginine-restricted diet with vitamin B6 supplementation was implemented; clinical assessments were repeated every 3 months during follow-up. Relative OAT mRNA expression was determined using real-time quantitative polymerase chain reaction. The 19-year-old compound heterozygous daughter (OAT: c.1186C&gt;T; c.748C&gt;T), had bilateral high myopia, posterior staphyloma, chorioretinal atrophy, macular abnormalities, and elevated hematologic ornithine. The 54-year-old heterozygous mother (OAT: c.1186C&gt;T), presented with bilateral severe myopia, asymmetric posterior staphyloma, retina and choroidal capillary layer atrophy, retinal pigment epithelium abnormalities, and mildly elevated hematologic ornithine. Compared to normal individuals, the daughter and mother had 29% and 46% relative OAT mRNA expression, respectively (P&lt;0.001). We believe that this is the first report of a carrier of one OAT variant allele with mild phenotypes, suggesting that family members should be aware of the possible involvement of autosomal recessive conditions. Additional data suggests nonsense mediated decay-initiated mRNA degradation may cause GACR.

Early discharge after childbirth has led to a rise in neonatal readmission, becoming a major concern in recent decades. Our research aimed to identify the risk factors and incidence of neonatal readmission, as well as explore preventive measures. Our study at the Clinical Hospital of Pediatrics in Ploiești, Romania included 108 neonates admitted during the neonatal period. This accounted for 2.06% of all admissions (5226). The most prevalent cases were malnutrition (25%), fever (20.3%) and bronchiolitis (17.5%). Diarrhea and infectious gastroenteritis were also observed (14.8%), along with acute rhinoconjunctivitis (9.2%) and late onset sepsis (3.7%). No deaths were recorded. The most significant characteristics identified were number of children (p&lt;0.001) and age at maternity discharge (p&lt;0.001). By following the prevention rules, malnutrition, feeding errors, and infections can be avoided. This includes practicing proper hand hygiene for both mothers and medical staff, as well as educating and demonstrating to mothers the benefits of breastfeeding. In addition, all newborns discharged from the maternity ward should benefit from follow-up at 7-10 days of life. Our results confirm the effectiveness of a multidisciplinary team and endorse promoting breastfeeding. Implementing quality control measures and regularly evaluating the surveillance program will help improve its effectiveness.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

In this paper, we introduce a specialized, fully automated experimental arrangement designed for assessing the effectiveness of augmented and virtual reality technologies in healthcare setting and explore its design principles focusing on depth sensor characterization. The main goal of this project is to establish a robust benchtop platform for the quantitative evaluation of extended reality technologies in a controlled environment, emphasizing the practical assessment of augmented reality head-mounted devices. We outline a design concept and considerations for an experimental configuration aimed at creating a realistic testing environment. This apparatus comprises an observation platform mounted on a three-degree-of-freedom motorized system and a test phantom stage. Focusing on real-case scenarios, we utilized a range of sensors, including readily available range-sensing cameras and commercial augmented reality headsets, such as the Intel RealSense L515 LiDAR camera, mounted on the motion control system. The setup enabled automated data collection and facilitates controlled assessments and validation of various facets of augmented reality technologies, including object, hand, and head tracking, as well as static and dynamic image registration. This paper describes the system architecture, the process of automated data collection, and presents several evaluation studies conducted with this setup, providing insights into the quality and temporal noise associated with static or moving objects or observers in augmented reality applications.

(1) Background: The RDW-CV has predictive value in many pregnancy-related conditions. Re-search question: Can the RDW-CV be utilized predictively in pregnant patients with thrombo-philia? Aim of the study: To carry out a detailed analysis of the RDW-CV in pregnant patients with treated thrombophilia as compared with pregnant patients without thrombophilia who de-livered via cesarean section at term. (2) Methods: We studied 160 pregnant patients, including 80 pregnant patients with treated thrombophilia in the study group, and another 80 patients of a similar age and parity. The patients were referred to our hospital for delivery at term by means of a cesarean section between 1/10/2017 and 1/12/2021. Every patient received a sonogram during the first 1–2 days after the cesarean section, and their uterine evaluation was interpreted using the PUUS (Postpartum Uterine Ultrasonographic Scale). (3) Results: Our PUUS≥1 pregnant and postpartum patients with treated thrombophilia were the only group with an RDW-CV value over 14. No deep vein thrombosis was observed during hospitalization, showing that the antico-agulant treatment was necessary and effective. An RDW-CV of 14.5 was the highest value in the Rh-negative group of pregnant patients with treated thrombophilia. An RDW-CV of 14.48 was the highest level in the Rh-negative postpartum patients with treated thrombophilia. (4) Conclu-sion: An RDW-CV of ≥14 can predict uterine hematometra (PUUS≥1). The RDW-CV values were higher in Rh-negative patients.