The carbonyl iron particles were dispersed in a polychloroprene rubber (CR) matrix under an external magnetic field for practical application as microwave absorption composites film. The film prepared under external magnetic field with a thickness of only 0.54 mm showed least reflection loss of -15.98 dB and the reflection loss value less than -10.0 dB over the frequency range of 11.4~14.8 GHz. In comparison with the microwave absorption properties of calculation by transmission line theory based on the tested relative complex permittivity and permeability and film prepared by general route without external magnetic field, the film made with external magnetic field exhibited more excellent microwave absorption properties, strongly depending on the increment of anisotropy and rearrangement of magnetic particles. The results indicated the composite film made under external magnetic field have excellent microwave absorption properties, which suggest that the composites thin film could be used as a thinner and lighter microwave absorber.

Utilization of wasted heat instead of fuel combustion is effective to reduce primary energy consumption for mitigating global warming problem. Because wasted heat sources are not necessarily located close to areas of heat demand, one of the difficulties is that wasted heat has to be transferred from heat source side to heat demand side, which may require heat transportation over long distance. From this point we proposed and have examined new idea of heat transportation using ammonia-water as the working fluid which system is named Solution Transportation Absorption chiller, in short STA. Our previous studies of STA were mainly the experimental investigation with STA facility which cooling power was 25RT (90kW). As a result, the COP of STA was found almost same value 0.65 with the conventional absorption chiller without depending on the transportation distances. The simulation using AspenHYSYS also examined with same experimental condition. The experimental data showed good agreement with the simulation calculation. In this study, we examined the large-scale cooling power STA on simulation. The examination cooling powers were from 90 kW(25RT) to 3517 kW(1000RT). All cooling power achieved around COP 0.64 including pump power consumptions. In addition, we performed the dynamic simulation. As the results, there was no effect of pipeline size on the cooling capacities and mass flow rates. Furthermore, the stability time of the cooling capacities and mass flow rates were almost same regardless of the pipeline size and cooling capacity. In other words, STA may be achieved the same COP even though having various complex conditions compared with the conventional absorption chiller.

Bio-inspired gyroid triply periodic minimum surface (TPMS) lattice structures have been the focus of research in automotive engineering because they can absorb a lot of energy and have wider plateau ranges. The main challenge is determining the optimal energy absorption capacity and accurately capturing plastic plateau areas using finite element analysis (FEA). Using nTop's Boolean subtraction method, this study combined walled TPMS gyroid structures with normal TPMS gyroid lattice. This made a composite TPMS-gyroid lattice with relative densities ranging from 14% to 54%. Using the ideaMaker software and the fused deposition modeling (FDM) Raise3D Pro 2 3D printer to print polylactic acid (PLA) bioplastics in 1.75 mm filament made it possible to slice computer aided design (CAD) models and fabricate 36 lattices samples precisely layer by layer technique. Shimadzu 100kN testing equipment was utilized for the mechanical compression experiments. And the validation using finite element analysis (FEA). Further, CTG was examined using a field emission scanning electron microscope (FE-SEM) before and after compression testing. The composite TPMS gyroid lattice showed potential as shock absorbers for vehicles with relative densities of 33%, 38%, and 54%. The Gibson-Ashby model showed that the composite TPMS gyroid lattice deformed mainly by bending, and the size effect was seen when the relative densities were less than 15%. The lattice's relative density had a significant impact on its ability to absorb energy. The research also explored the use of these innovative foam-like composite TPMS-gyroid lattices in high-speed crash box scenarios, potentially enhancing vehicle safety and performance.

Membrane gas absorption technology has been considered as a promising approach to mitigate CO2 emissions from power plants. The aim of this study is to evaluate the environmental impacts of CO2 absorption and desorption processes by hollow fiber membrane contactors using life cycle assessment methodology. On the basis of ReCipe 2016 Midpoint and ReCipe 2016 Endpoint methods, the research results show that, membrane gas absorption system exhibits the lowest environmental impacts across the majority assessed categories in comparison with chemical absorption and membrane gas separation systems. The CO2 capture process via membrane gas absorption has the most significant impact on METP category, with heat consumption as the primary contributing factor accounting for 55%, followed by electricity consumption accounting for 43.1%. According to the sensitivity analysis, heating by natural gas shows a better performance than other heat supply sources in improving overall environmental impacts. In addition, the increasing utilization of renewable energy in electricity supply reduces the global warming potential, fossil resource consumption and ozone formation.

Volumetric modification of transparent materials by femtosecond laser pulses is successfully used in a wide range of practical applications. The level of modification is determined by the locally absorbed energy density, which depends on numerous factors. In this work, it is shown experimentally and theoretically that, in a certain range of laser pulse energies, the peak of absorption of laser radiation for doughnut-shaped (DS) pulses is several times higher than for Gaussian ones. This makes the DS pulses very attractive for material modification and direct laser writing applications. Details of the interaction of laser pulses of Gaussian and doughnut shapes with fused silica obtained by numerical simulations are presented for different pulse energies and compared with the experimentally obtained data. The effect of absorbed energy delocalization with increasing laser pulse energy is demonstrated for both beam shapes while, at relatively low pulse energies, the DS beam geometry provides a stronger local absorption compared to Gaussian one. Implications of a DS pulse action on post-irradiation material evolution are discussed based on thermoelastoplastic modeling.

This study examines the absorption and concentration of anthracene (AN) in the garden radish. Studies were conducted to grow radishes from the sowing stage in soil contaminated with AN, and to grow radishes in soil contaminated with AN following maturity (27 days after sowing). For the growth in AN-containing soil from sowing onward, AN levels immediately after seeding ranged from 12,500-36,300 ng/g-ww. AN concentrations during growing period ranged from 7140-16,000 ng/g-ww in soil and from 38.2-2160 ng/g-ww in radish, respectively. For the growth in AN-containing soil after maturity, AN concentrations in soil and radish ranged from 9560-22,100 ng/g-ww and 342-2270 ng/g-ww. The concentrations of AN in the roots and leaves had a higher density than those in the stems. In these experiments, positive relationships between AN levels in soil and radishes were observed. It is inferred that the greater the degree of soil contamination, the greater the effect on the amount of AN assimilated by the radishes. The concentration ratio (radish-to-soil; Cr/Cs) decreased exponentially with days since AN application. This indicates that the concentration ratio is affected by time in contact with AN. According to the results for the change over time of Cr/Cs and contents by radish part, it is thought that AN in the soil has good absorption through the roots to circulate within the organism, and is preferentially distributed and accumulated in the roots and leaves, which have high organic matter content.

Oral ferric citrate hydrate (FCH) is effective for iron deficiency in hemodialysis patients.; however, it remains unclear how iron balance in the body affects iron absorption from the intestinal tract. This prospective, observational study (Riona-Oral Iron Absorption Trial, R-OIAT, UMIN 000031406), conducted at 42 hemodialysis centers in Japan, wherein 268 hemodialysis patients without inflammation were enrolled and treated with a fixed amount of FCH for 6 months. We assessed the predictive value of hepcidin-25 for iron absorption and iron shift between ferritin (FTN) and red blood cells (RBCs) following FCH therapy. Serum iron changes at 2 h (ΔFe2h) after FCH ingestion were evaluated as iron absorption. The primary outcome was the quantitative delineation of iron variables on ΔFe2h and the secondary outcome was the description of the predictors of body iron balance. Generalized estimating equations (GEE) were used to identify the determinants of iron absorption during each phase of FCH treatment. ΔFe2h increased when hepcidin-25 and MCH decreased (-0.155, -0.242 to -0.068, p = 0.001; -2.574, -4.421 to -0.726, p = 0.006, respectively) in GEE. Hepcidin-25 increased when erythropoiesis-stimulating agent (ESA) decreased (-0.002, -0.002 to -0.001, p=0.000). FTN increased when RBC and ESA decreased (-0.466, -0.605 to -0.327, p=0.000; -0.002, -0.004 to -0.000, p=0.05, respectively. Limiting erythropoiesis to maintain hemoglobin levels induces RBC reduction in hemodialysis patients, resulting in increased hepcidin-25 and FTN levels. Hepcidin-25 production may prompt an iron shift from RBC-iron to FTN-iron, inhibiting iron absorption even with continued FCH intake.

The capability of in-house transient wave-multibody computational tool of ITU-WAVE are extended to predict the wave power absorption with Wave Energy Converters (WECs) arrays placed in front of a vertical breakwater. The analyses of hydrodynamic exciting and radiation forces are approximated solving boundary integral equation at each time interval. The reflection of incoming waves due to a vertical wall is predicted with method of images. The constructive or destructive performance of WECs arrays with different array configurations is measured with mean interaction factor. The behaviour of the exciting and radiation hydrodynamic forces of each WEC due to a vertical wall effect shows considerable differences than those of WECs arrays without a vertical wall influence. When the wave power absorption with WECs arrays with and without a vertical wall effect are compared, it is shown with numerical experiences that WECs placed in front of a vertical wall have much greater effects on wave power absorption. This can be attribute to the hydrodynamic interaction, standing waves, and nearly trapped waves in the gap between a vertical wall and WECs arrays. The analytical and other numerical results are used to for the validation of the numerical results of the present ITU-WAVE computational tool for exciting and radiation forces, and mean interaction factor of WECs arrays which show satisfactory agreements.

Acoustic metasurface are artificial structures which could manipulate the wavefront in sub-wavelength dimensions and the previous proposed acoustic metasurface were mostly realized with single materials. An acoustic metasurface with composite structure is proposed for underwater acoustic stealth considering both wavefront manipulation and sound absorption. The unit cells of the metasurface are composed by metallic supporting lattice, interconnecting polymer materials and mass balancing columns. With the gradual modulations of equivalent physical properties along the horizontal direction of metasurface, the incident acoustic wave is reflected to other directions. Meanwhile, the polymer material inside the unit cells would dissipate the acoustic wave energy due to inherent damping properties. With the simultaneous modulations of reflected wave direction and scattering acoustic amplitude, significant improvement of underwater stealth effect is achieved. Compared with single-phase metasurface, the Far-Field Sound Pressure Level (FFSPL) of the multiphase metasurface decreased by 4.82 dB within the frequency range of 3kHz~30kHz. Under a hydrostatic pressure of 5MPa, the linearized mean stress for multiphase metasurface is only 1/3 of that of single-phase metasurface due to much thicker struts and much more uniform stress distribution. The proposed composite structure possesses potential applications due to acceptable thickness (80mm) and low equivalent density (1100 kg/m3).

A solid structure, such as a road, building wall or envelop, used as a solar collector is considered an effective and new way to use renewable energy. This paper focused on the temperature characteristics of four structures exposed to sunshine: asphalt, red brick, composite cement and concrete road slab. Furthermore, the collected heat based on a hydraulic system was investigated experimentally. For the four structure slabs, their temperature differences are due to solar radiation absorption varied greatly by the material’s heat absorptance and color. Through the test, asphalt slab attained the highest temperature and had the weakest reflection among the structures. Compared with the others, the temperature of the asphalt slab was greater by 8.1%, 14.9% and 16.4% than the brick, composite cement and concrete, respectively. The reflection intensity growth ratio was defined and indicates the growth potential for absorbing radiation in the solid slab surface. From the experiments, it was concluded that a suitable selection of road materials can greatly improve the thermal absorption, conduction and penetration into the solid slab. The collected heat capability was approximately 250 W/m2 to 350 W/m2 in the natural summer condition. A black coating or a surface modification can collect more heat, reaching greater than 250 W/m2. The solar collecting heat efficiency with a surface configuration of the road slab can reach above 30% in the summer time.

As a rapidly expanding family of two-dimensional (2D) materials, MXenes have recently gained considerable attention due to their appealing properties. Here, by developing a solution-based coating method that enables transfer-free and layer-by-layer film coating, we investigate the layer-dependent nonlinear optical absorption of Ti₃C₂T_x films ‒ an important member of the MXene family. By using the Z-scan technique, we characterize the nonlinear absorption of the prepared MXene films consisting of different numbers of monolayers. The results show that there is a strong and layer-dependent nonlinear absorption behavior, transitioning from revisable saturable absorption (RSA) to saturable absorption (SA) as the layer number increases from 5 to 30. Notably, the nonlinear absorption coefficient β varies significantly within this range, changing from ~7.13 × 10² cm/GW to ~-2.69 × 10² cm/GW. We also characterize the power-dependent nonlinear absorption of the MXene films at various incident laser intensities, and a decreasing trend in β is observed for increasing laser intensity. These results reveal the intriguing layer-dependent nonlinear optical properties of 2D MXene films, highlighting their versatility and potential for implementing high-performance nonlinear photonic devices.

Implementation of waterflood is with injected pressured water to reservoir to escalation oil production. Produced water is the dominated result from oil and gas mechanism in this world meanwhile 65% of water is injected back to the well for pressure maintenance, 30% for discharge aquifier condition and surface. For shaly sand, produced water usually bring coarse and suspended sand to the surface. Therefore, this sand level is needed to declining to avoid plugging in injection well until certain economic condition.

Imidacloprid is the first-generation neonicotinoid insecticide. But, the long-term use of im-idacloprid as a pesticide has caused severe water pollution. Recently, the toxicity of imidacloprid to aquatic organisms has received increasing attention. This study aimed to investigate the ab-sorption and distribution of imidacloprid in various tissues (gills, intestine, liver, muscle, brain, and gonads) of goldfish through short-term and continuous exposure tests for 28 days. The re-sults of short-term exposure indicated that the concentration of imidacloprid and its metabolites in tissues at the transfer stage decreased steadily after 1 day of 40 mg/l imidacloprid water treatment and was below the detection limit after 3 days. Continuous exposure for 28 days at various treatment concentrations showed that the concentrations of imidacloprid and its metab-olites differed significantly among the different tissues of the goldfish. In the 20 mg/l treatment group (S1), the highest concentration of imidacloprid was found in the liver (12.04 μg /gtissue), followed by the intestine (9.91 μg /gtissue), muscle (6.20 μg /gtissue), gill (6.11 μg /gtissue), gonads (5.22 μg /gtissue), and brain (2.87 μg /gtissue). In the 40 mg/l treatment group (S2), the order of tissue concentrations was similar to that of the S1 group, with the highest concentration observed in the liver (12.04 μg/gtissue), followed by the intestine (9.91 μg/gtissue), muscle (6.20 μg/gtissue), gill (6.11 μg/gtissue), gonads (5.22 μg/gtissue), and brain (2.87 μg/gtissue). Fur-thermore, the study detected 5-hydroxyimidacloprid, imidacloprid urea, and 6-chloronicotinic acid in imidacloprid metabolites in all tissues, while imidacloprid was detected only in the intes-tine and liver. Overall, the results of this study contribute to a better understanding of the met-abolic behavior of imidacloprid in organisms and provide new data to support the assessment of imidacloprid toxicity in fish.

One of the drawbacks of natural fibers and their composites is their inherent hydrophilic nature. The effect of moisture on mechanical properties of a composite is irrefutable. This study deals with hygroscopic characteristics of Enset-PLA composites and its effect on the mechanical properties of the composite. To do this, injection molded composite specimens of different fiber volume fraction; plasticizer ratio, fiber length, and fiber age have been considered. The specimens are exposed to distilled water and the moisture absorption was monitored on a daily base. Subsequently, the specimens are subjected to mechanical loading to determine the effect of moisture on their Strength, Stiffness and strain at break strength. Lastly, individual and joint effects of considered factors have been scrutinized using optimal design of experiment. The result from the study shows that maximum and minimum moisture uptake is noticed for 25% and 10% fiber ratio respectively. Due to moisture effect, tensile and bending strength is decreased by 11% and 5% respectively for 15% fiber volume fraction; while 16% and 13% for 25% fiber volume fraction respectively. Increasing amount of plasticizer increases moisture resistance. The result indicate that Enset-PLA composite have competitive properties and stability when exposed to moisture.

Highly efficient, broadband and distinctively structured electromagnetic wave (EMW) absorption materials exhibit huge exceptions with multi-functions in both military and civilian fields. Searching the relationship between structural and EMW performance is beneficial to develop outstanding microwave absorption materials, and has become an attractive research topic. In this study, we briefly reviewed the different EMW absorption mechanisms and key influence factors, then, present the latest developments in low-dimensional (LD) EMW absorption materials. We provide a comprehensive discussion of remarkable examples and summarize the main information related to the structure-function relationship of dimensional design and structural engineering in order to facilitate the rapid evolution of this fascinating field.

β-glucan is a generic term for insoluble dietary fibers exerting various effects on the immune system. As a group, β-glucans are non-cellulose polysaccharides composed of a glucopyranose as the main constituent sugar with β configuration, having a β- (1,3)-linked glucopyranose main chain as a common feature. β-glucans are absorbed through the intestine. Since the 1980s, there have been many studies reporting various effects of β-glucans on the immune system, including reports on receptors, that have slowly clarified their recognition system and action mechanisms. However, these studies focused mostly on treatments of infectious diseases and tumors; thus, the effects of β-glucans ingested in food as dietary fiber and their mechanisms of action remain largely unknown. The uptake of β-glucan into the body may be resemble that of proteins, which are soluble polymers, and insoluble material such as dietary fiber. Dietary fibers have varied structures, with wide-ranging solubility and physiological effects. Understanding whether these substances are actually taken up, how they exert their effects, and their metabolism after being taken up are important issues when considering the functionality and safety of dietary fibers.

Molecule radiation can be used as a tool to study colder regions in switching arc plasmas like arc fringes in contact to walls and ranges around current zero (CZ). This is demonstrated in the present study for the first time for the case of ablation-dominated high–current arcs as key elements of self–blast circuit breakers. The arc in a model circuit breaker (MCB) in CO2 with and an arc in a long nozzle under ambient conditions with peak currents between 5 and 10 kA were studied by emission and absorption spectroscopy in the visible spectral range. The nozzle material was polytetrafluoroethylene (PTFE) in both cases. Imaging spectroscopy was carried out either with high-speed cameras or with intensified CCD cameras. A pulsed high-intensity Xe lamp was applied as background radiator for the broad-band absorption spectroscopy. Emission of Swan bands from carbon dimers was observed at the edge of nozzles only or across the whole nozzle radius with highest intensity in the arc center, depending on current and nozzle geometry. Furthermore, absorption of C2 Swan bands and CuF bands were found with the arc plasma serving as background radiator. After CZ, only CuF was detected in absorption experiments.

M87 is the best available source for studying the AGN jet-launching region. To enrich our knowledge of this region, with quasi-simultaneous observations using VLBA at 22, 43 and 86~GHz, we capture the images of the radio jet in M87 on a scale within several thousand R_s. Based on the images, we analyze the transverse jet structure and obtain the spectral-index distribution in the jet. We find that the absorption is enhanced at the collimation regions and the interruption of the jet. The external medium, which may not be uniform, may have contributed a lot to the absorption in the jet-launching region. Additionally, the temporal morphology of the jet in its launching region may be largely affected by the local, short-lived kink instability growing in itself.

The production of SOX by ship engines is a serious environmental problem and has been addressed by international standards. The restrictions limit the sulphur content of the fuel to 0.5% by mass to reduce SOX emissions; however, using low sulphur fuels such as LNG causes logistical and operational problems and a higher costs. For these reasons, there has been renewed interest in developing devices such as the Seawater Scrubber (SWS). This paper describes a simplified numerical model to simulate the absorption of SO2 in a drop of water during a dynamic "wet scrubbing" process. The dependence on the initial conditions is demonstrated by running multiple simulations as the initial droplet diameter, temperature and SO2 concentration in the flue gas vary. The work shows how the amount of sulphur dioxide absorbed is strongly related to the concentration in the exhaust gases and the initial diameter of the droplet, and highlights how distributions of droplets smaller than an upper limit value optimize the absorption process.

Two-dimensional mass spectrometry (2D MS) is a method for tandem mass spectrometry that relies on manipulating ion motions to correlate precursor and fragment ion signals. 2D mass spectra are obtained by performing a Fourier transform in both the precursor ion mass-to-charge ratio (m/z) dimension and the fragment ion m/z dimension. The phase of the ion signals evolves linearly in the precursor m/z dimension and quadratically in the fragment m/z dimension. This study demonstrates that phase-corrected absorption mode 2D mass spectrometry improves signal-to-noise ratios by a factor of 2 and resolving power by a factor of 2 in each dimension compared to magnitude mode. Furthermore, phase correction leads to an easier differentiation between ion signals and artefacts, and therefore easier data interpretation.

A laser-based hydrogen (H₂) sensor using wavelength modulation spectroscopy (WMS) was developed for contactless measurements of molecular hydrogen. The sensor uses a distributed feedback (DFB) laser to target the H₂ quadrupole absorption line at 2121.8 nm. The H₂ absorption line exhibits weak collisional broadening and strong collisional narrowing effects. Both effects were investigated by comparing measurements of the absorption linewidth with detailed models using different line profiles that include collisional narrowing effects. The collisional broadening and narrowing parameters were determined for pure hydrogen as well as for hydrogen in nitrogen and air. Performance of the sensor was evaluated and the sensor applicability for H₂ measurements in a range of 0- 10 %v of H₂ was demonstrated. A precision of 0.02 %v was achieved with 1 meter of absorption pathlength (0.02 %v∙m) and 1 s of integration time. For the optimum averaging time of 20 s a precision of 0.005 %v∙m was achieved. A good linear relationship between H₂ concentration and the sensor response was observed. A simple and robust transmitter-receiver configuration of the sensor allows in-situ installations in harsh industrial environments.

An in-depth understanding of the Se uptake and metabolism in plants is necessary for developing Se biofortification strategies. Thus, hydroponic experiments were conducted to investigate the associated processes and mechanisms of organic Se [selenomethionine (SeMet) and selenomethionine-oxide (SeOMet)] uptake, translocation, transformation and their interaction in wheat, in comparison to inorganic Se. Results showed that Se uptake by roots and the root-to-shoot translocation factor under the SeMet treatment were higher than those under the selenite, selenate, and SeOMet treatments. The uptake and translocation of SeMet were higher than those of SeOMet within 72 h, although the differences gradually narrowed with time. The uptake of SeMet and SeOMet was also sensitive to the aquaporin inhibitor: AgNO3 addition resulted in 99.5% and 99.9% inhibition of Se in root in the SeMet and SeOMet treatments, respectively. Once absorbed by root, were rapidly assimilated to other Se forms, and SeMet and Se-methyl-selenocysteine (MeSeCys) were the dominant species in SeMet and SeOMet-treated plants, while notably, an unidentified Se form was also found in the root and xylem sap under the SeMet treatment. In addition, within 16 h, SeOMet inhibited the uptake and translocation of SeMet, while the interaction was weakened with longer treatment time. Taken together, the present study provides new insights for the uptake and transformation processes of organic Se within plants.

Lack of shock absorption capability of conventional steel bollards causes significant vehicle damage and consequently high repair costs. This research studies a solution to reduce vehicle damage by inserting PLA honeycomb structures. A honeycomb-inserted bollard was designed based on numerical simulations using LS-DYNA, which yielded the bollard designed for actual vehicle-bollard collision experiments. Simulation efforts were focused on calculating the acceleration characteristics when a vehicle collides with steel and honeycomb-inserted bollards. Compared to the simulated steel bollards, 20 MPa yield-strength honeycomb-inserted bollard showed 0.017s delay in the maximum acceleration occurrence time, reduction of the maximum acceleration to 37.4% of that of steel bollards, and 13.1% reduction in the B-pillar maximum acceleration. Actual vehicle-bollard collision experiments, with a gyro-sensor installed at the test vehicle front bumper frame, also proved improved shock absorption characteristics of the honeycomb-inserted bollards. An experiment with honeycomb-inserted bollard showed 0.783s delay in the maximum acceleration occurrence time, a significant delay when compared to steel bollards. The maximum acceleration measured by the gyro-sensor was 0.35m/s2 when the simulation predicted it to be 0.388 m/s2, proving the similarity in the simulations and experiments. Thus, this study of shock absorption characteristics promised reduced damage to vehicles and lower repair cost.

The interaction between single or a fixed number of photons with a single absorber is of fundamental interest in quantum technology. The harnessing of light matter interactions at the single particle limit has several potential applications ranging from quantum communication and quantum metrology to quantum imaging. In this letter, a setup for heralded two-photon absorption at the single absorber level is proposed. The setup is based on a heralded two-photon source utilizing spontaneous parametric down-conversion, entanglement swapping and sum frequency generation for joint detection. The feasibility of the scheme is discussed by reviewing recent achievements in utilizing entangled and correlated photons for two-photon absorption as well as single photon absorption experiments at the limit of single absorbers in the context of applications in imaging (here mainly microscopy) and spectroscopy.

Three types of the composites were tested for electromagnetic interference (EMI) absorption shielding effectiveness, curing process and physical-mechanical properties. In the first type of composites, manganese-zinc ferrite, nickel-zinc ferrite, and both fillers in their mutual combinations were incorporated into acrylonitrile-butadiene rubber. The overall content of the filler, or fillers combinations was kept on 200 phr. Then, carbon black, or carbon fibres, respectively were incorporated into each rubber formulation in constant loading - 25 phr, while the content of magnetic fillers was unchanged - 200 phr. The work was focused on the understanding of correlation among electromagnetic shielding parameters and electrical conductivity of composites in relation to their EMI absorption shielding effectiveness. The absorption shielding ability of materials was evaluated within the frequency range from 1 MHz to 6 GHz. The study revealed good correlation among permittivity, conductivity, and EMI absorption effectiveness. Although, the absorption shielding efficiency of composites filled only with ferrites seems to be the highest, the absorption maxima of those composites were reached over 6 GHz. The application of carbon based fillers resulted in higher electrical conductivity and higher permittivity of composites, which was reflected in their lower absorption shielding performance. Though, the composites with filled with ferrites and carbon based fillers absorbed electromagnetic radiation within the desired frequency range. The presence of carbon based fillers caused the improvement in tensile behavior of composites. The study also demonstrated that the higher was the ratio of nickel-zinc ferrite in magnetic fillers combinations, the higher was the absorption shielding performance.

Intraband energy transitions of an electron in GaAs/AlGaAs hexagonal quantum well wires in the presence of external electric and magnetic fields are presented. We consider the effects of the revolve of the quantum well wires via a geometric factor that converts the quantum wires straight and symmetric with respect to the z−axis, into a curved wires that no longer has this symmetry. In addition, the influence of having a shallow donor impurity on (off) is calculated. The shape of this quantum string corresponds to the core/shell structure. The energy levels and wave functions of the electron in the heterostructure with a finite potential between the shells are calculated using the effective mass approximation and the finite element method. The calculations of the optical properties are obtained from the compact density matrix and an iterative method. The direction of the applied external fields is parallel (anti-parallel) to the z−direction. The results reveal a significant dependence of the physical properties calculated with the deformation parameter, the dimensions of the quantum well wires and the presence or not of the impurity. The electronic transitions are in a range between 4.90 meV to 41.50 meV under the effect of the electric field, this corresponds to a range of frequencies of optical responses between 1.20 to 10 THz, that is, the mid-infrared. For the magnetic field the range is between 1.24 meV to 14 meV, that is, in frequencies from 0.36 to 3.38 THz, that is, in the far-infrared.

Broadband reverse saturable absorption is systematically investigated via Z-scan, transient absorption spectrum (TAS). The excited state absorption and negative refraction of Orange IV are observed in the Z-scan experiment at 532 nm. Meanwhile, two-photon induced excited-state absorption and pure two-photon absorption are observed at 600 nm and 700 nm with the pulse width of 190 fs, respectively. An ultrafast broadband absorption in visible wavelength region is observed via TAS. The different nonlinear absorption mechanism at multiple wavelengths is discussed and interpreted from the results of TAS. In addition, the ultrafast dynamics of negative refraction in the excited state of Orange IV is investigated via degenerate phase object pump probe, from which the weak long-lived excited state is extracted. All studies indicate that Orange IV has the potential to be further optimized into a superior broadband reverse saturable absorption material and also has certain reference significance for the study of optical nonlinearity in organic molecules containing azobenzene groups.

We consider a new model of a branching random walk on a multidimensional lattice with continuous time and one source of particle reproduction and death, as well as an infinite number of sources in which, in addition to the walk, only absorption of particles can occur. The asymptotic behavior of the integer moments of both the total number of particles and the number of particles at a lattice point is studied depending on the relationship between the model parameters. In the case of the existence of an isolated positive eigenvalue of the evolution operator of the average number of particles, a limit theorem is obtained on the exponential growth of both the total number of particles and the number of particles at a lattice point.

Ammonia known as harmful gas that could impact on health and environment. Typically, ammonia gas emitted by fertilizer industry, rubber factory, etc. There are many options for advance industry to control ammonia gas pollution, absorption tower using water scrubber and using activated carbon as adsorption reaction could be an option. But for middle- and lower-class industry, it is common in Indonesia, as seen on many rubber factories, ammonia gas pollution is serious problem to control, actually they have used wet scrubber but eficiency is lower about 47%. This study measure performance for ammonia elimination as gas pollutant using absorption tower and adsorption tower in laboratory scale. Using electrochemical gas sensor, we measure both ammonia concentration for inlet and outlet simultaneously to settle saturation point of these two types of ammonia emission control. In conclusion, Ammonia absorbed in water proportional to saturation time and absorbent volume. Highest absorbed ammonia concentration 1.538 mg/L on 4000 mL absorbent. For Adsorption system, saturation time proportional and correlated to adsorbent weight and Adsorption capacity reverse correlated to adsorbent weight. Optimum adsorption point can be achieved from intersection curve between saturation time and adsorption capacity which is 1200 grams adsorbent

The research paper comprehensively and consistently addresses all relevant theoretical areas related to the topic and includes an extensive empirical analysis of the absorption of EU funds and their impact on the sustainable development of Croatia, Slovenia, Hungary, and Poland. The analysis aims to investigate the efficiency of the absorption of funds from the EU, the impact of these funds on regional development of countries, as well as the reasons for such impacts. The "Regional Development Model Based on EU Funds" was tested with the aim of applying the model to the Republic of Croatia, countries in the region, and other European countries to achieve a higher level of absorption of financial resources from the available EU funds. Data for the empirical analysis were collected using a highly structured survey questionnaire on a sample of 244 respondents involved in the preparation and implementation of EU-funded projects. The contribution of economic science in theoretical terms arises from the development of scientific knowledge and ideas about the importance of increasing the number of development projects that will increase the absorption of funds from the European Union, thereby increasing economic activities in Croatia and the region. The expected contribution of economic science in the applied sense is based on the formulation of the "Regional Development Model Based on EU Funds," which is based on the application of knowledge, good practices, and stakeholder experiences, considering relevant indicators from available sources. The greatest contribution is demonstrated through testing the "Regional Development Model Based on EU Funds," which is applicable to the Republic of Croatia, countries in the region, and other European countries over a longer period. Finally, research of the impact of EU funds on the regional development of recipient countries is considerably less represented and very modest, only in the "upswing" of systematic scientific research. The research aims to fill the gaps in research and encourage thinking of key stakeholders responsible for regional development, who should eventually realize the importance of defining a regional policy aimed at EU funds as a key to regional development and reducing regional disparities within countries.

With the rapid development of electronic and communication technology in military radar, the demand for microwave absorbing materials in low-frequency with thin layer is growing increasingly. In this study, flexible Co3O4/CC (carbon cloth) composites derives from Co-MOFs (metal-organic frameworks)/CC are prepared by hydrothermal and thermal treatment processes. The flexible precursors of Co-MOFs/CC are calcined with different calcination temperatures, which the material structure, dielectric properties and microwave absorption performance are changed. With the increase of calcination temperature, the minimum reflection loss of the corresponding Co3O4/CC composites gradually moves to the lower frequency with thinner thickness. In addition, the Co3O4/CC composites with 25 wt% filler loading ratio exhibit the minimum reflection loss (RL) of -46.59 dB at 6.24 GHz with 4.2 mm thickness. When the thickness is 3.70 mm, the effective absorption bandwidth is 3.04 GHz from 5.84 to 8.88 GHz. This study not only proves that the composite Co3O4/CC is a kind of outstanding microwave absorbing material with better flexibility, but also provides a useful inspiration for the low frequency and broadband microwave absorbing material.

A labyrinth metamaterial wall with glass coverage is measured in a reverberating chamber and after its installation in a restaurant. Glass is used to meet two aims, namely acoustic absorption and visual design demands. The wall consists of five multiple labyrinth elements of 1.83 m$^2$ each. Glass was taken to make the wall act as a room lightning device where a translucent cover material is needed. Absorption measurements show about four times improved absorption compared to typical glass. Due to the metamaterial behavior, absorption is high in the low-frequency range below 300 Hz where damping is problematic with traditional materials. Especially in this range, the glass metamaterial wall is an excellent compromise between room acoustic and visual design demands, as loud low-frequencies make visitors speak louder and experience less intimacy with additionally reduced speech intelligibility. For mid-frequencies, absorption is shown less effective and improvements are discussed.

Vertical III-V semiconductor nanowires have shown promising absorption of light for solar cell and photodetector applications. The absorption properties can be tuned through the choice of III-V materials and geometry of the nanowires. Here, we review recent progress in the design of the absorption properties of both individual nanowires and nanowire arrays. Future directions for the research field are proposed.

This research aims to investigate the carbon fiber reinforced polymer (CFRP) when subjected to tensile, bending, and compression. Half of the specimens are also subjected to water to find out how water influences. The CFRP is created using a combination of carbon fiber layers and epoxy resin Bisphenol A Epichlorohydrin with hardener and is formed using the vacuum infusion method. From the water absorption test, it was found that the average weight gain of the specimens was 2.9% and the lowest value was at 0.6%, it was concluded that the increase in wet specimen weight was not too significant and water absorption tended to be slow. Mechanical testing ob-tained the highest average tensile stress, bending stress, compressive stress, and modulus of elasticity of 195 MPa, 295 MPa, 96 MPa, and 8914 MPa were from dry specimens while the lowest average values were 146 MPa, 286 MPa, 81 MPa, and 6160 MPa from wet specimens. The results of micro-photo observations on the tensile test fracture show that the specimen has a XGM fracture character with delamination and splitting fractures happening in multiple areas. In the bending test, the specimens experienced buckling fracture due to the fiber breaking and the inability of the matrix to withstand the additional stress. Shear fracture happened during the compressive test. In conclusion, water absorption has a bad impact towards the composite strength.

The discovery of more bioactive compounds for non-invasive administration has been the goal of research groups focused on pharmacotherapy. Phytonutrients have always been attractive for researchers because they are a significant source of bioactive phytochemicals, but it is challenging to determine which components show high biomedical activity. However, based on the chemical structure of these active compounds, their physicochemical properties can be calculated to predict the probability of gastrointestinal (GI) absorption after oral administration. Indeed, different researchers have proposed several rules (e.g., Lipinski's, Veber's, Ghose's, and Muegge's rules) to attain these predictions for synthetic compounds. Most phytochemicals do not fully comply with these rules even though they show high bioactivity and high GI absorption experimentally. Here, we provide a detailed methodology using web-based platforms to determine the physicochemical properties of five phytochemicals in the phytonutrients ginger, echinacea, and tobacco. Furthermore, we analyzed the calculated data and established a protocol based on the combination and integration of these rules, plus other extended parameter ranges, to reliably predict the GI absorption of natural compounds. The presented data and methodology can be beneficial for evaluating bioactive natural compounds as potential drug candidates and predicting their oral bioavailability in patients.

This letter aims to show the connection between the sinc approximation for high-energy absorption cross section and the shadow radius of the spherically symmetric black hole. This connection can give a physical interpretation of the absorption cross section in the eikonal limit parameters. Moreover, the use of this alternative way, one can extract its shadow radius from the absorption cross section in high energy limits to gain more information about the black hole spacetime. Our results indicate that the increasing the value of the shadow radius of the black hole, exponentially increase the the absorption cross section of the black hole in high-energy limits which can be captured by the Event Horizon Telescope (EHT) collaboration.

Iron and zinc are essential micronutrients required for growth and health. Deficiencies of these nutrients are highly prevalent among populations, but can be alleviated by supplementation. Cross-sectional studies in humans showed positive association of serum zinc levels with hemoglobin and markers of iron status. Dietary restriction of zinc or intestinal specific conditional knock out of ZIP4 (SLC39A4), an intestinal zinc transporter, in experimental animals demonstrated iron deficiency anemia and tissue iron accumulation. Similarly increased iron accumulation has been observed in cultured cells exposed to zinc deficient media. These results together suggest a potential role of zinc in modulating whole body iron metabolism. Studies in intestinal cell culture models demonstrate that zinc induces iron uptake and transcellular transport via induction of divalent metal iron transporter-1 (DMT1) and ferroportin (FPN) expression, respectively. It is interesting to note that intestinal cells are exposed to very high levels of zinc through pancreatic secretions, which is a major route of zinc excretion from the body. Therefore, zinc appears to be modulating the iron metabolism possibly via regulating the DMT1 and FPN1 levels. Herein we critically reviewed the available evidence to hypothesize novel mechanism of Zinc-DMT1/FPN axis in regulating intestinal iron absorption and tissue iron accumulation to facilitate future research aimed at understanding the yet elusive mechanisms of iron and zinc interactions.

This work discusses laboratory measurements of atomic and diatomic molecular species in laser-plasma generated in gases. Noticeable self-absorption of the Balmer series hydrogen alpha line occurs for electron densities of the order of one tenth of standard ambient temperature and pressure density. Emission spectra of selected diatomic molecules in air or specific gaseous mixtures at or near atmospheric pressure reveal minimal plasma re-absorption. Abel inversion of the plasma in selected gases and gas mixtures confirm expansion dynamics that unravel regions of atomic and molecular species of different electron temperature and density. Time resolved spectroscopy diagnoses self-absorption of hydrogen alpha and hydrogen beta lines in ultra-high pure hydrogen gas. Radiation from a Nd:YAG laser device induces micro-plasma for pulse widths in the range of 6 ns to 14 ns, energies in the range of 100 mJ to 800 mJ, and for peak irradiance of the order 1 to 10 TW/cm². Atomic line profiles yield electron density and temperature from fitting of line profiles to wavelength and sensitivity corrected spectral radiance data. Analysis of measured diatomic emission data yields excitation temperature of primarily molecular recombination spectra. Applications of the laboratory experiments extend to investigations of stellar astrophysics white dwarf spectra.

Veterinary antibiotics (VAs) have been indiscriminately used in animal feed for the past five decades to increase and ensure profits with negligible environmental considerations. The VAs amoxicillin (AMX), chlortetracycline (CTC), and oxytetracycline (OTC), which can be unintentionally introduced by irrigation water during rice cultivation, were evaluated for their phytotoxic effects, absorption-translocation into plants, and soil residues using a randomized complete block design. It was found that exposure to VAs can severely affect the photosynthetic pathway of rice plants. The uptake and translocation of VAs by rice plants varied significantly. CTC and OTC translocated more easily than AMX, a member of the β-lactam class, which accumulated at the lowest concentration compared to CTC and OTC across all treatments. Rice yield was about 4.3 - 5.7% lower in the experimental plots that received fifty-fold the background levels of VAs compared to the control. The findings indicate that these widely used veterinary antibiotics can hamper crop production, leave residues in the soil, and constitute a risk to human health if introduced into the agro-ecosystem unintentionally.

The high level of noise in helicopter cabins considerably compromises the comfort and safety of the pilot and passengers. To verify the feasibility and effectiveness of microperforated panel composite sound absorption structures for noise suppression in helicopter cabins, simulation and experimental studies were conducted on a model of a light helicopter cabin. First, three microperforated composite sound absorption structures for the helicopter cabin wall panel were designed. Then, a finite element model of the main gear/body acoustic vibration coupling was established to obtain the target frequencies of the microperforated composite sound absorption structures; the acoustic effect was verified by simulation. Finally, a model helicopter cabin equipped with the three microperforated composite sound absorption structures was built, and a cabin noise test was performed. The test results showed that the combined microperforated panel acoustic structure and microperforated panel–porous material composite structure realized an overall cabin sound pressure level attenuation of 8–10 dB, on average, in the wide frequency range of 500–2000 Hz, with an amplitude of more than 20 dB. The microperforated panel–acoustic supermaterial composite structure achieved low-frequency sound absorption in the frequency range of 300–450 Hz. The sound absorption effect reached 50%, and it also exhibited good noise reduction effects in the middle- and high-frequency bands.

A sustainable matrix based on eucalyptol essential oil/sawdust was developed and applied on one-sided laminated plywood. This finish aims to serve as a eucalyptol odor slow release. Eucalyptol odor release was monitored with gas chromatography coupled with a flame ionization detector (GC – FID: Limits of Detection and Quantification of 0.70 g/m3 and 2.11 g/m3, respectively, and with linearity up to 18.6 g/m3). Measurement of the eucalyptol odor released was performed during a six-month period and it was found that the release followed a first-order exponential decay with a decay rate constant of 0.0169 per day. The half-life was determined to be of 48 days. The granulometry and particle size porosity of sawdust were analyzed by Scanning Electron Microscopy. Sawdust size fraction between 112 – 200 μm showed best eucalyptol absorption capacity with 1:3 masses ratio (sawdust:eucalyptol). The time capacity of eucalyptol release depends of composite eucalyptol – sawdust quantity. Where this relation was determined: 15.0 grams of composite eucalyptol-sawdust by 0.8 mm diameter aperture gave 6 months of eucalyptol release, that was considered very positive, understanding high volatility of eucalyptol and a small quantity of composite for further products. The new product is characterized by a carbon footprint (considering the industry frontiers) of 5.94 kg CO2eq/m2 of plywood floor.

Current industrial trends bring new challenges in energy absorbing systems. Polymer materials as the traditional packaging material seem to be promising due to their low weight, structure and production price. Based on the review, the linear low-density polyethylene material was identified as the most promising material for absorbing impact energy. The current paper addresses the identification of the material parameters and the development of a Constitutive material model to be used in future design by virtual prototyping. The paper deals with the experimental measurement of the stress-strain relations of the linear low-density polyethylene under static and dynamic loading. The quasi-static measurement is realized in two perpendicular principal directions and is supplemented by a test measurement in the 45 degrees direction, i.e. exactly between the principal directions. The quasi-static stress-strain curves are analyzed as an initial step for dynamic strain rate dependent material behavior. The dynamic response is tested in the drop tower using a spherical impactor hitting the flat material multi-layered specimen at two different energy levels. The strain rate dependent material model is identified by optimizing the static material response obtained in the dynamic experiments. The material model is validated by the virtual reconstruction of the experiments and by comparing the numerical results to the experimental ones.

Single nanowires (NWs) are of great importance for optoelectronic applications, especially solar cells serving as powering nanoscale devices. However, weak off-resonant absorption can limit its light-harvesting capability. Here, we propose a single NW coated with the graded-index dual shells (DSNW). We demonstrate that with appropriate thickness and refractive index of the inner shell, the DSNW exhibits significantly enhanced light trapping compared with the bare NW (BNW), and the NW only coated with the outer shell (OSNW) and the inner shell (ISNW), which can be attributed to the optimal off-resonant absorption mode profiles due to the improved coupling between the reemitted light of the transition modes of the leak mode resonances of the Si core and the nanofocusing light from the dual shells with the graded refractive index. We found that the light absorption can be engineered via tuning the thickness and the refractive index of the inner shell, the photocurrent density is significantly enhanced by 134% (56%, 12%) in comparison with that of the BNW (OSNW, ISNW). This work advances our understanding of how to improve off-resonant absorption by applying graded dual-shell design and provides a new choice for designing high-efficiency single NW photovoltaic devices.

Coffee and caffeine have been used as solar absorbers and also to increase the thermal stability and efficiency of perovskite solar cells. In this work, we report the sensing of extremely alkaline pH by colloidal coffee solution aided by generation of an optical absorption band in the near-UV region. This generation of absorption band could be explained by the orientation induced dipole-dipole interactions arising from differing caffeine-solvent interactions with varying pH. Such a generation leads to the lowering of direct as well as indirect bandgaps from 4 eV-->2.8 eV& 3.4 eV-->2.5 eV, respectively. We also estimate the changes in optical energy storage efficiency, inferring it to be highest for pH 11 having the highest intensity of the generated absorption band (λ_abs≈360 nm). With these observations and further deductions, the work reported in this paper would be of immense interest to the researchers working in the field of development of chemical pH sensors and also in the development of novel UV absorbers.

One of the most common limits to gas sensor performance is the presence of unwanted interference fringes or etalons arising, for example, from multiple reflections between surfaces in the optical path. Additionally, since the amplitude and the frequency of these interference depend on the distance and alignment of the optical elements, they are affected by temperature changes and mechanical disturbances, giving rise to a drift of the signal. In this work, we present a novel semi-parametric algorithm which allows the extraction of a signal, like the spectroscopic absorption line of a gas molecule, from a background containing arbitrary disturbances, without having to make any assumption on the functional form of these disturbances. The algorithm is applied first to simulated data and then to oxygen absorption measurements in presence of strong fringes.To the best of the authors' knowledge, the algorithm enables an unprecedented accuracy particularly if the fringes have a free spectral range and amplitude comparable to those of the signal to be detected. The described method presents the advantage of being based purely on post processing, and to be of extremely straightforward implementation if the functional form of the Fourier transform of the signal is known. Therefore it has the potential to enable interference-immune absorption spectroscopy. Finally, its relevance goes beyond absorption spectroscopy for gas sensing since it can be applied to any kind of spectroscopic data.

Biodegradable and renewable plastic films have been regarded as promising alternative green materials to achieve the substitution polythene (PE)films to reduce plastic pollution. Poly (butylene adipate-co-terephthalate) (PBAT) is a kind of biodegradable polyester, which is widely used in the production of biodegradable mulching films. However, the high cost of PBAT limited it applications. Thus, lignin, one of the most abundant biomass resources was incorporated into PBAT matrix in the present work. A series of Lignin/PBAT biodegradable plastics films with different Lignin/PBAT weight ratios (0.00 %-5.00 %) were successfully fabricated using twin screw and twin roll extruders. The chemical compositions, morphologies, thermal stabilities, mechanical properties, and barrier properties of samples were characterized by XRD, FTIR, TG/DSC, mechanical testing machine, and WVTR, respectively. Results show that the corporation of lignin into PBAT matrix could lead to improved thermal stabilities, mechanical properties and barrier properties of films even after Xenon lamp aging process, especially when Lignin/PBAT weight ratio is 1.00 % in the present work. This work provides a very promising approach for fabrication of biodegradable plastics films with low cost, enhanced mechanical properties and barrier properties, the as-prepared samples may have potential applications in agricultural or food packaging materials.

We discuss a remote sensing system that is used to simultaneously detect range-resolved differential absorption LIDAR (light detection and ranging; DIAL) signals and integrated path DIAL signals (IP-DIAL) from aerosol targets for ranges up to 22 km. The DIAL/IP-DIAL frequency converter consists of an OPO pumped at 1064 nm to produce light at 1.6 μm and operates at 100 Hz pulse repetition frequency. The probe light is free space coupled to a movable platform that contains one transmitter and two receiver telescopes. Hybrid photon counting/current systems increase the dynamic range for detection by two orders of magnitude. Range resolved and column integrated dry-air CO2 and CH4 mixing ratios are obtained from line shape fits of CO2 and CH4 centered at 1602.2 nm and 1645.5 nm, respectively and measured at 10 different frequencies over ≈ 1.5 cm-1 bandwidth. The signal-to-noise ratios (SNR) of the IP-DIAL returns from cloud aerosols approach 1000:1 and the uncertainties in the mixing ratios weighted according to the integrated counts over the cloud segments range from 0.1 % to 1 %. The range averaged DIAL mixing ratios are in good agreement with the IP-DIAL mixing ratios at the 1 % to 2 % level for both CO2 and CH4. These results can serve as a validation method for future active and passive satellite observational systems.

This study presents a tri-layer broadband metamaterial absorber which operates in the GHz range. The absorber was composed of a polyhedral iron-cobalt alloy/graphite nanosheet material arranged in a flat sheet with two punched-in rings for the top layer, a continuous FR-4 layer at the middle, and a continuous copper layer at the bottom. For the normal incidence of electromagnetic wave, the proposed absorber demonstrated an exceptional broadband absorption in a frequency range of 7.9-14.6 GHz, revealing an absorption exceeding 90%. The absorption magnitude remains to be above 90% in a frequency range of 8-11.1 GHz for transverse-electric-polarized waves at incident angles up to 55°. For both transverse-magnetic- and electric-polarized waves, the absorption exceeds 90% in a frequency range of 9.5-14.6 GHz. The physical mechanism behind the absorption properties is analyzed thoroughly through the electric- and magnetic-field distributions. The obtained results could contribute potentially to the development of microwave applications based on metamaterial absorbers, such as radar-stealth technology, electromagnetic shielding for health safety and reduced electromagnetic interferences for high-performance communications and electronic devices.

Among the various methods for collecting oil spills and oil products, including from the water surface, one of the most effective is the use of sorbents. In this work, three-component bio-based composite granular adsorbents were produced and studied for oil products pollution collection. A bio-based binder made of peat, devulcanised crumb rubber from used tyres, and part fly ash as cenospheres were used for absorbent production. The structure, surface morphology, porosity, mechanical properties, and sorption kinetics of the obtained samples were studied. Composite hydrophobicity and sorption capacity to oil products such as diesel fuel (DF) and motor oil (MO) were determined. The obtained pellets are characterised by a sufficiently pronounced ability to absorb oil products such as DF. As the amount of CR in the granules increases, the diesel absorption capacity increases significantly. The case of 30-70-0 is almost 3 times higher than the granules from homogenised peat. The increase in q is due to two factors: pronounced surface hydrophobicity of the samples (Θ = 152°) and a heterogeneous porous granule structure. The presence of the cenosphere in the biocomposite reduces its surface hydrophobicity while increasing the diesel absorption capacity. Relatively rapid realisation of the maximum saturation by the MO was noted. In common, the designed absorbent shows up to 0.7 g·g^-1 sorption capacity for MO and up to 1.55 g·g^-1 sorption capacity for diesel. A possible mechanism of DF absorption and the limiting stages of the process approximated for different kinetic models are discussed. The Weber-Morris diffusion model is used to primarily distinguish the limiting effect of external and internal diffusion of adsorbate on the absorption process

Examining forbidden reflections provides valuable information on electronic states and the local environment of resonant atoms in crystals. Experimental studies of two forbidden reflections 002 and 100 in TeO₂ single crystals were performed at photon energies close to the L₁ tellurium absorption edge. It was found that the spectral form corresponding to these two reflections looks almost identical, which is completely unexpected for a highly anisotropic material. Theoretical consideration shows that only one component f_xy of the tensor describing dipole-dipole resonance scattering contributes to the 002 reflection, while two components f_xy and f_xz correspond to the 100 reflection. Numerical calculations show that the latter tensor component is comparable to the first one, but the combination of several geometric factors leads to the fact that its contribution to the spectrum is negligible. This explains the experimentally observed results. The finding shows a way for targeted investigation of single tensor components and makes it possible to compare different spectra and use them the study the physical phenomena in functional materials.

The gap in knowledge regarding the radiative effects of aerosols in the UV region of the solar spectrum is large, mainly due to the lack of systematic measurements of the aerosol single scattering albedo (SSA) and absorption optical depth (AAOD). In the present study, spectral UV measurements performed in Thessaloniki, Greece by a double monochromator Brewer spectrophotometer in the period 1998 - 2017 are used for the calculation of the aforementioned optical properties. The main uncertainty factors have been described and there is an effort to quantify the overall uncertainties in SSA and AAOD. Analysis of the results suggests that the absorption by aerosols is much stronger in the UV relative to the visible. SSA follows a clear annual pattern ranging from ~0.7 in winter to ~0.85 in summer at wavelengths 320 – 360 nm, while AAOD peaks in summer and winter. The average AAOD for 2009 – 2011 is ~50% above the 2003 – 2006 average, possibly due to increased emissions of absorbing aerosols related to the economical crisis and the metro-railway construction works in the city center. A detailed analysis of the uncertainties in the retrieval of the SSA and the AAOD from the Brewer spectrophotometer has been also performed.

The resonance spectra of neutral silver indicate self-absorption for the studied Ag I lines at the wavelengths of 327.9 nm and 338.2 nm. The center dip is associated with self-reversal due to self-absorption in the plasma. The Q-switched radiation of 355 nm, 532 nm, or 1064 nm from a Nd:YAG laser device generates the plasma at the surface of silver nano-material targets, with experiments conducted in standard ambient temperature and pressure laboratory air. Procedures for recovery of the spectral line shapes confirm that over and above the effects of self-reversal, line shape distortion are important in the analysis. The work discusses parameters describing self-absorption when using fluence levels of 2 to 33 J/cm² to generate the plasma. Furthermore, subsidiary calibration efforts that utilize the hydrogen alpha line of the Balmer series show that the Ag I lines at 827.35 nm and 768.7 nm are optically thin.

Dye wastewater containing bisphenol A (BPA) and dyes as pollutants have not been adequately studied. Our previous study revealed that thermoplastic polyurethane (TPU) nanofiber membranes (NFMs) modified by the addition of polyethyleneimine (PEI) and polydopamine (PDA) satisfactorily adsorb dyes. Herein, we first optimized the synthesis conditions for such membranes, noting a PEI:PDA monomer ratio of 2:2 and a deposition time of 48 h to be optimal. Experiments using these membranes revealed that binary systems containing BPA and the dyes (Congo red (CR), Eosin yellow (EY), or sunset yellow (SY)) exhibit three adsorption behaviors. CR and BPA compete with each other for adsorption sites, decreasing the maximum adsorption capacity (Qmax) for CR 208.3 mg/g (in a monomeric system) to 182.4 mg/g, whereas for BPA, it decreased from 26.7 to 22.8 mg/g. The adsorption rates for CR and BPA decreased from 0.002 min−1 and 0.331 min−1 in the monomeric systems to 8.37 × 10−4 min−1 and 0.072 min−1, respectively, in the binary CR–BPA system, exhibiting antagonistic effects. When EY and BPA coexist, Qmax for EY increased from 60.0 (monomeric) to 71.9 mg/g, whereas that for BPA increased from 35.6 to 43.2 mg/g, showing a synergistic effect due to the possible bridging effect. The adsorption sites for SY and BPA are independent of each other. Thus, PDA/PEI TPU NFMs exhibit the potential for removal of dye–BPA composites, whereas binary systems containing BPA with different dyes are adsorbed differently.

Abstract: The ongoing use of plastic polymers to manufacture food packaging has raised concerns about the presence of nano- and microplastics (NMPs) in a variety of foods. This review provides the most recent data on NMPs' migration from plastic packaging into milk and dairy products. Also discussed are the possible effects of NMPs on nutrient digestion, absorption, and metabolism. Different kinds of milk products, including skimmed or whole liquid and powder milk, infant formula milk, and other dairy products, have been found to contain NMPs of various sizes, shapes, and concentrations. NMPs may interact with proteins, carbohydrates, and fats and have a detrimental impact on how well these nutrients are digested and absorbed by the body. The presence of NMPs in the gastrointestinal tract may impact how lipids, proteins, glucose, iron, and energy are metabolised, increasing the risk of developing health conditions such as diabetes, cardiovascular disease, hypertension, and some cancers. In addition to NMP, plastic oligomers released from food packaging material have been found to migrate to various food simulants and milk, though their effect on human health has yet to be investigated. Viewpoints on potential directions for future studies on NMPs and nutrient digestion, absorption, and health are also presented in this review.

Background: Restorative materials might significantly affect load transmission at peri-implant bone. The aim of the present study is to evaluate the shock absorption capacity of two different polymeric materials to be used as frameworks for implant-supported prostheses. Methods: A masticatory robot was used to compare the shock absorption capacity of polyether-ketoneketone (PEKK) Pekkton®ivory (Cendres+Mètaux) and glass fiber-reinforced composite (GFRC) TRINIATM (Bicon). Five identical sample crowns for each of the materials was tested un-der the same conditions described in previously published papers (Menini et al. 2013). Forces transmitted at the simulated periimplant bone were recorded and statistically analysed. Results: The statistical analysis of forces transmitted at the simulated dental implant revealed significant differences between all the materials tested and significant differences with the mate-rials tested in a previously published paper (Menini et al. 2013: zirconia, glass ceramic, composite resin, acrylic resin). Only differences between PEKK and veneered PEKK and between PEKK and one of the previously tested composite resins were not statistically significant. PEKK samples demonstrated significantly greater shock absorption capacity compared to GFRC. Conclusions: PEKK revealed optimal shock absorption capacity. Further studies are needed to evaluate its efficacy in case of long span prostheses with reduced prosthetic volume.

OsNRAMP5—a member of the same family as the iron, manganese (Mn), and cadmium (Cd) transporter OsNRAMP1—is responsible for the transport of Mn and Cd from soil in rice. Knockout of OsNRAMP5 markedly reduces both Cd and Mn absorption; therefore, in low -Mn environments, such plants would exhibit Mn deficiency and suppressed growth. Amino acid mutations in IRT1 alter its metal selectivity. We generated random mutations in OsNRAMP5 via error-prone PCR, and used yeast to screen for the retention of Mn absorption and inhibition of Cd absorption. The results showed ththat alanine 512th is the most important amino acid residue for Cd absorption, and that its substitution resulted in the absorption of Mn but not Cd.

Data on the atmospheric gas concentrations can be received with high efficiency and on a large spatial scale only from remote laser sounding instruments. The remote laser techniques with the use of lidars are widely used in the study of the atmosphere and control of its state. The aims of this work are the design and test in numerical and field experiments of a DIAL OPO lidar system based on KTA and KTP crystals for gas analysis of the atmosphere. Lidar measurements of atmospheric gases in the near/mid infrared region have been numerically simulated. The differential absorption lidar system based on optical parametric oscillators with nonlinear KTA and KTP crystals which allow laser radiation tuning both in the near and in the middle IR spectral region is described; it allows tuning laser radiation in the near/mid-IR wavelength regions. Lidar echo signals have been experimentally recorded in the 1.8–2.5 and 3–4 m wavelength ranges. The results of H2O and CO2 profile measurements along the surface sounding path are presented.

The purpose of this study is to develop and evaluate a self-microemulsifying drug delivery system (SMEDDS) to improve the oral absorption of poorly water-soluble Olaparib. Through the solubility test of Olaparib in various oils, surfactants and co-surfactants, pharmaceutical excipients for use in SMEDDS manufacturing were selected. Self-emulsifying regions were identified by mixing the selected materials at various ratios, and a pseudoternary phase diagram was constructed by synthesizing these results. Various physicochemical properties of microemulsion incorporating Olaparib were confirmed by investigating the particle morphology, particle size, zeta potential, drug content and stability. In addition, the improved dissolution and oral absorption of Olaparib were also confirmed through a dissolution test and a pharmacokinetic study. An optimal microemulsion was generated in the formulation of Capmul MCM EP/NF 10%, Labrasol 80% and PEG 400 10%. Fabricated nano-sized microemulsions were well-dispersed in aqueous solutions, and it was also confirmed that it was maintained well without any problems of either physical or chemical stability. The 5 min initial dissolution of Olaparib in fabricated formulations was improved by 10.6 times (pH1.2), 14.8 times (pH6.8) and 14.8 times (distilled water) compared to the values of Olaparib powder. The dissolution at 120min was 45.4±4.0%(pH1.2), 53.5±1.1% (pH6.8) and 58.1±1.00% (distilled water) in Olaparib powder but has been significantly improved by 1.7 times (74.8±1.9%), 1.6 times (84.2±0.3%) and 1.5 times (81.2±0.7%) in SMEDDS. Associated with the high dissolutions of Olaparib in fabricated microemulsions, the pharmacokinetic parameters were also greatly improved. The Cmax and AUCinf of Olaparib in the prepared microemulsion were increased 4.2- and 3.2-fold, respectively, compared to powder. Taken together with the results mentioned above, the microemulsion system could be an effective tool as an oral delivery formulation for Olaparib. Additionally, our results demonstrate that the SMEDDS systems comprising Capmul MCM, Labrasol and PEG 400 could be a useful option for improvement of several other poorly water-soluble drugs with physico-chemical properties similar to Olaparib.

Upland cotton is sensitive to 2,4-dichlorophenoxyacetic acid (2,4-D), and the identification of potentially 2,4-D tolerant cotton chromosome substitution (CS) lines and understanding tolerance mechanisms provide a significant step into the development and genetic improvement of upland cotton to reduce yield loss caused by 2,4-D herbicide effects including the drifts. Experiments were conducted to understand the possible mechanism of herbicide tolerance in CS-T04-15, CS-T07, and CS-B15sh, 2,4-D herbicide-tolerant cotton CS lines compared with TM-1, the 2,4-D herbicide susceptible recurrent parent of the CS line as control, using [14C]2,4-D. Percent absorption rate and translocation patterns of the 14C-labeled herbicide application at 5.17 kBq at 6 to 48 hours after treatment (HAT) were determined. The tolerant cotton CS lines showed 15-19% [14C]2,4-D uptake while TM-1 exhibited a reduced uptake of only 1.4% [14C]2,4-D at 24 HAT. Distribution of the absorbed [14C]2,4-D showed that 2-5% was translocated outside the treated leaf. In TM-1, 77% of the herbicide was translocated above and below the treated leaf, contrasting with the reduced translocation of 14C-labeled herbicide observed in the tolerant CS lines. Interestingly, CS-T04-15 showed a restricted movement of 14C below the treated leaf at 6 to 48 HAT, suggesting a novel mechanism of herbicide tolerance. This finding is the first report on upland cotton demonstrating a complex differential uptake and translocation associated with herbicide tolerance for [14C]2,4-D in cotton CS lines.

The use of plant fibers as reinforcement in composites with the aim of totally or partially replacing synthetic fibers has received significant attention in the last years. However, one of the disadvantages of the use of these fibers in polymeric composites is associated to the fact that they are hydrophilic, resulting in poor adhesion with most matrices when in the presence of moisture. In addition, another problem encountered is the lower strength of this type of fiber and, as a solution to minimize these problems, the composite can be hybridized by adding layers of natural and synthetic fibers and the use of resin protection along the thickness of the composite. (Lateral protection) to reduce moisture absorption by the laminate. The objective of this work is to obtain composites formed by five layers of reinforcement and terephthalic polyester matrix, one of which is reinforced only with short glass fiber-E blanket, another reinforced only with jute fiber and a third hybrid containing the fibers. Two types of reinforcements with interlayer layers. Afterwards, the loss of mechanical properties was observed when these materials were immersed in distilled water, with and without lateral protection, until reaching saturation. We evaluated parameters such as the influence of configuration type and environmental conditions, such as the amount of water absorption. The obtained results show that the hybrid composite obtained a behavior close to the composite containing only fiberglass, and better than the one containing only jute fiber and that the absorption was smaller in the samples with side protection.

Docosahexaenoic acid (DHA) is an essential fatty acid (FA) with proven health effects, whom bioavailability improvement is becoming a public health issue. Unlike fish oils, the bioavailability of DHA from microalgal (A) has not been fully assessed, particularly with regard to the molecular structuring capabilities offered by A-oil. We explored the impact of 5 formulas rich in DHA, different by i) the molecular structure: ethyl ester (EE) or monoglyceride (MG) or Triglyceride (TG) and ii) the supramolecular form: emulsified TG or TG+phospholipids (blend PL), on the lymphatic kinetics of DHA absorption and the lipid characteristics of resulting lipoproteins. We demonstrated that in rat, the DHA absorption of the conventional A-DHA TG structure was more effective than the EE structure (+ 23%). More, the A-DHA MG and A-DHA Emulsion were the most favourable DHA-vectors (AUC: 89% and +42%, respectively), thanks to an improved lipolysis. The A-DHA MG and -Emulsion presented the richest DHA content in TG (+40%) and PL (+50%) of lymphatic chylomicrons, which could impact the metabolic fate of DHA. We concluded that structuring A-DHA in TG or EE would be more prone for tissue and hepatic metabolism whereas in A-DHA MG and A-DHA Emulsion could target nerve tissues.

Combined systems for power production and thermally activated cooling have a high potential for improving the efficiency and utilisation of thermal systems. In this regard, various configurations have been proposed and are comprehensively reviewed. They are primarily based on absorption systems and the implementation of multiple levels of complexity and flexibility. The configuration of the absorption power and cooling combined cycle proposed herein has wide commercial applicability owing to its simplicity. The configuration of the components is not new. However, the utilisation of aqueous salt solutions, the comparison with ammonia chiller and with absorption power cycles, the focus on parameters that are important for real-life applications, and the comparison of the performances for constant heat input and waste heat recovery are novel. The proposed cycle is also compared with a system based on the organic Rankine cycle and vapour compression cycle. An investigation of its performance proves that the system is suitable for a given range of boundary conditions from a thermodynamic standpoint, as well as in terms of system complexity and technical feasibility. New possibilities with regard to added power production have the potential to improve the economics and promote the use of absorption chiller systems.

In this research, a design method for the graded triply periodic minimal surface (TPMS) structures with lightweight, high-strength, and high sound absorption properties is proposed. The graded TPMS structures are controlled by linear, quadratic, and sine functions. Uniform TPMS and graded TPMS were manufactured by laser powder bed fusion (LPBF) with AlSi7Mg powder, and an acoustic impedance tube test, compression test, and digital image correlation (DIC) test were ap-plied to obtain the sound absorption and compression properties. The sound absorption coefficient of a uniform Gyroid increases as the number of layers and surface thickness increase, and it in-creases as element size decreases. The sound absorption peak shifts to low frequencies as the number of layers increases. The sound absorption property of Type-Ⅰ graded TPMS is superior to the Type-Ⅱ, and the G-LinearⅠ has the highest sound absorption properties among the three functions. It reveals that the graded TPMS has superior sound absorption performance at low and medium frequencies. The compression and DIC results of graded TPMS also show excellent mechanical properties and energy absorption characteristics.

In this paper, the classical least square (CLS) method with molecular absorption spectrophotometric measurement was used to determine simultaneously of paracetamol (PAR), ibuprofen (IBU), and caffeine (CAF) in tablets. The absorbance spectra of the standard solutions and samples were measured over a wavelength from 220 to 300 nm with a 0.5 nm step. The concentration of PAR, IBU and CAF in the sample solutions were calculated by using a program called CLS-Excel written in Microsoft Excel 2016 and Visual Basic for Applications (VBA). The method and CLS-Excel program were tested on mixed standard laboratory samples with different PAR, IBU, and CAF concentration ratios, and they showed small errors and satisfying repeatability. An analytical procedure for tablets containing PAR, IBU, and CAF was developed. The reliability of the procedure was proved via the recovery and repeatability of the analysis results with an actual tablet sample and comparing the mean contents of active substances in the tablets obtained from the analytical procedure with the from the HPLC method. The procedure is simple with a reduced cost compared with the HPLC standard method.

Hypercholesterolemia accelerates atherosclerosis, and extensive research has been undertaken to ameliorate this abnormality. Plant sterols have been shown to inhibit cholesterol absorption and lower plasma cholesterol level since the 1950s. This ingredient has recently been reappraised as a food additive that can be taken daily in a preclinical period to prevent hypercholesterolemia, considering that cardiovascular-related diseases are the top cause of death globally even with clinical interventions. Intestinal cholesterol handling is still elusive, making it difficult to clarify the mechanism for plant sterol-mediated inhibition. Notably, although the small intestine absorbs cholesterol, it is also the organ that excretes it abundantly, via trans-intestinal cholesterol efflux (TICE). In this review, we show a model where the brush border membrane (BBM) of intestinal epithelial cells stands as the dividing ridge for cholesterol fluxes, making cholesterol absorption and TICE inversely correlated. With this model, we tried to explain the plant sterol-mediated inhibitory mechanism. As well as cholesterol, plant sterols diffuse into the BBM but are effluxed back to the lumen rapidly. We propose that repeated plant sterol shuttling between the BBM and lumen promotes cholesterol efflux, and plant sterol in the BBM may disturb the trafficking machineries that transport cholesterol to the cell interior.

Reconstruction of acoustic relaxation absorption curve is a powerful approach to ultrasonic gas sensing, but requires known of a series ultrasonic absorption at various frequencies around effective relaxation frequency. Ultrasonic transducer is a most widely deployed sensor for ultrasonic wave propagation measurement and works only at a fixed frequency or specific environment like water, so a large number of ultrasonic transducers operating at various frequencies are required to recover an acoustic absorption curve with a relative large bandwidth, which cannot suit for large-scale practical applications. This paper proposes a wideband ultrasonic sensor using a distributed Bragg reflector (DBR) fiber laser for gas concentration detection through acoustic relaxation absorption curve reconstruction. With a relative wide and flat frequency response, the DBR fiber laser sensor measures and restores a full acoustic relaxation absorption spectrum of CO2 using a decompression gas chamber between 0.1 and 1 atm to accommodate the main molecular relaxation processes, and interrogates with a non-equilibrium Mach-Zehnder (M-Z) interferometer to gain a sound pressure sensitivity of -45.4 dB. The measurement error of the acoustic relaxation absorption spectrum is less than 1.32%.

The main goal of our work is the revealing of problematic issues related to estimates of the absorption coefficient of colored organic matter in the northern seas from data of the Ocean and Land Color Instrument (OLCI) on the Sentinel-3 satellites. In particular, a comparison of the OLCI standard error estimates ADG443_NN_err., relating to the measurement and retrieval of the geophysical products, with the uncertainties in the real situation of the northern seas, where the natural conditions are extremely unfavorable (first of all, frequent cloudiness, low Sun heights). We conducted a comprehensive multi-sensor study of the uncertainties using various approaches, first at all, directly comparing the data from satellite (OLCI Sentinel-3 and four other ocean color sensors) and field measurements in five sea expeditions 2016-2019, by using the different processing algorithms. Our analysis has shown that the real uncertainties of the final product are significantly higher than the calculated errors of the ADG443_NN_err., which is 100% and ~10%. The main reason for that is the unsatisfactory atmospheric correction. We present the results of the analysis of the different effecting factors (satellite sensors, processing algorithms, use of the other parameters), and formulate the tasks of future work.

Conventional mechanical Fourier Transform Spectrometers (FTS) are able to simultaneously measure absorption and dispersion spectra of gas-phase samples. However, they usually need very long measurement times to achieve time-resolved spectra with a good spectral and temporal resolution. Here, we present a mid-infrared dual-comb-based FTS in an asymmetric configuration, providing broadband absorption and dispersion spectra with a spectral resolution of 5 GHz, a temporal resolution of 20 μs, and a total measurement time of a few minutes. We used the dual-comb spectrometer to monitor the reaction dynamics of methane and ethane in an electrical plasma discharge. We observed ethane/methane formation as a recombination reaction of hydrocarbon radicals in the discharge in various static and dynamic conditions. The results demonstrate a new analytical approach for measuring fast molecular absorption and dispersion changes and monitoring fast dynamics of chemical reactions, which can be interesting for chemical kinetic research and particularly for the combustion and plasma analysis community.

The present work evaluates the food effect on the absorption of rivaroxaban (Riva), a BCS II drug, from the orally administered commercial immediate-release tablet (Xarelto IR) using physiologically based pharmacokinetic (PBPK) and conventional in vitro- in vivo correlation (IVIVC) models. The bioavailability of Riva upon oral administration of Xarelto IR tablet is reported to exhibit a positive food effect. The PBPK model for Riva was developed and verified using the previously reported in vivo data for oral solution (5 and 10 mg) and Xarelto IR tablet (5 and 10 mg dose strength). Once the PBPK model was established, the in vivo performance of the tablet formulation with the higher dose strength (Xarelto IR tablet 20 mg in fasted and fed state) was predicted using the experimentally obtained data of in vitro permeability, biorelevant solubility and in vitro dynamic dissolution data using United States Pharmacopeia (USP) IV flow-through cell apparatus. In addition, the mathematical IVIVC model was developed using the in vitro dissolution and in vivo profile of 20 mg strength Xarelto IR tablet in fasted condition. Using the developed IVIVC model, the pharmacokinetic (PK) profile of the Xarelto IR tablet in fed condition was predicted and compared with the PK parameters obtained via the PBPK model. A virtual in vivo PK study was designed using a single-dose, 3-treatment cross-over trial in 50 subjects to predict the PK profile of the Xarelto® IR tablet in the fed state. Overall, the results obtained from the IVIVC model were found to be comparable with that from the PBPK model. The outcome from both the model pointed to the positive food effect on the in vivo profile of the Riva. The developed models thus can be effectively extended to establish bioequivalence for the marketed and novel complex formulations of Riva such as amorphous solid dispersions.

Phase change materials (PCMs) have emerged as promising solutions for latent heat thermal energy storage (LHTES) systems, offering considerable potential for storing energy derived from renewable sources across various engineering applications. The present study focused on optimization of solar cooling system by integrating LHTES with different PCM tank configuration. TRNSYS simulation software was selected for the study and collected experimental data from laboratory system prototype was used for system validation. The results indicate that the use of PCM led to a noteworthy decrease of 6.2% in auxiliary energy consumption. Furthermore, the duration during which the heat carrier temperature flow exceeded 90°C from the storage tank to the auxiliary heater was extended by 27.8% when PCM was utilized, compared to its absence. The use of PCM in LHTES is more effective under variable weather conditions. On the day when changes in weather conditions were observed, around 98% of the cooling load was provided by produced sun energy. The results of the research can be used to optimize the solar cooling system, which will help reduce the environmental impact of cooling systems running on non-renewable fuels.

Light absorption in single nanowires (NWs) is one of the most crucial factors for photovoltaic applications. In this paper, we carried out a detailed investigation of light absorption in single rectangular NWs (RNWs). We show that the RNWs exhibit improved light absorption compared with the square NWs (SNWs), which can be attributed to the symmetry-breaking structure that can increase the light path length by increasing the vertical side and the enhanced leaky mode resonances (LMRs) by decreasing the horizontal side. We found that the light absorption in silicon RNWs can be enhanced by engineering the horizontal and vertical sides, the photocurrent is significantly increased by 276.5% or 82.9% compared with that of the SNWs with the same side length as the horizontal side of 100 nm or the vertical side of 1000 nm, respectively. This work provides an effective way for designing high-efficiency single NW photovoltaic devices based on the symmetry breaking from the SNWs to RNWs.

In this work, a tailored extreme learning machine (ELM) algorithm to enhance the overall robustness of gas analyzer based on the tunable diode laser absorption spectroscopy (TDLAS) method is presented. The ELM model is tailored through activation function selection, input weight and bias searching, and cross validation method to address the analyzer robustness issues for industrial process analysis field application. The two particular issues are the inaccurate gas concentration measurement caused by the process gas background components variation, and the inaccurate spectra shift calculation caused by spectral interference. By using our algorithm, the concentration error is reduced by one order of magnitude over a much larger stream pressure and component range compared with that obtained by classical least square (CLS) fitting methods based on reference curves. Additionally, it is shown that with our algorithm, the wavelength shift accuracy is improved to less than 1 count over 1000 counts spectra length. In order to test the viability of our algorithm, a trace ethylene (C₂H₄) TDLAS analyzer with coexisting methane was implemented, and its experimental measurements support analyzing robustness enhancement effect.

Resistive patch array incorporating with metallic backplane provided an effective way to the achievement of broadband metamaterial absorbers(MAs). When loading metallic metamaterial to resistive MA, the outstanding construction helps realize more flexible and diversified forms of broadband absorption. In this paper, we attempted to load metallic resonators(MRs) to resistive MA in the three-dimensional construction, which benefits further enhancement of lower-frequency absorption. Simulation showed that the partial absorption band was separated to lower frequency, while the rest of broadband absorption was unaffected. Meanwhile, after combining multi-unit of the proposed MAs, the stair-stepping broadband absorption was also achieved. At last, three samples were fabricated. The agreements between simulations and experimental results demonstrated that resistive MA loaded with MRs provided an effective way for further enhancement of lower-frequency absorption with almost no change of the absorbing structure and areal density. Thus, it is worthy to expect a wide range of applications to emerge inspired from the proposed attempt.

Iron (Fe), the main component of non-exhaust particulates, is known to have variable health effects that depend on the chemical species of iron. This study characterized the possible contribution of iron oxides and hydroxides to airborne brake-wear particles under realistic vehicle driving and braking conditions with different brake-pad friction materials. We found significant differences in wear coefficients and PM₁₀ emissions between non-asbestos organics (NAO) and European performance (ECE) brake pads. Iron was the dominant contributor to PM₁₀ and PM_2.5 brake-wear particles for both NAO and ECE. The iron concentration ratio in the particle mass were comparable to the disc to pads ratio measured by wear mass. The fact that magnetite, which is of interest with respect to health effects, was less abundant in NAO than in ECE suggested that tribo-oxidations occurred in NAO. Metallic iron is generated not only from abrasive wear but also from tribo-chemical reduction with magnetite as the starting material. We found differences not only in PM emissions between brake friction materials but also that the phase transformations of iron differed between friction materials. These differences were apparent in the distribution of iron oxides and hydroxides. Heat, tribo-oxidation, and tribo-reduction are intricately involved in these reactions.

Microwave absorbers with lightweight, good stability and high efficiency have attracted much attention for their applications in many contemporary fields. In this work, the 3D porous (Ni@NO-C)n/NO-C composite absorber was prepared by a wet chemistry method with Ni chains and melamine as precursors, in which NO-C (N,O-doped carbon) encapsulated Ni particles are homogenously dispersed in the 3D porous networks of NO-C in the form of (Ni@NO-C)n chains. The special microstructure of the as-prepared material is proved to be benefit for the improvement of its microwave adsorption performance. The as-synthesized (Ni@NO-C)n/NO-C composite ab-sorber exhibited an effective absorption bandwidth of 4.1 GHz and an extremely large reflection loss of -72.3 dB. The excellent microwave absorbing performances can be ascribed to the coopera-tive consequence of dielectric loss and magnetic loss along with the balance between attenuation capability and impedance match.

Because of lower solubility and considerable metabolism, vardenafil (VRD) bioavailability is 15 %. To get over this obstacle, this study aimed to increase the solubility, hasten the onset of action, and mask the unpleasant taste of VRD utilizing β-cyclodextrin (β-CD) and formulation of the inclusion complex as oral disintegrating tablets (ODTs). The solubility of the obtained complexes in various ratios has been studied. A Box-Behnken design (BBD) was utilized to investigate the influence of excipients on the quality of ODTs. The solubility of VRD was improved at 1:2 drug: β-CD ratio. The formulated VRD-ODTs exhibited satisfying results regarding the hardness and disintegration time. In addition, in vivo taste masking and disintegration time showed improved results, after placing the tablets in the oral cavity of the healthy volunteers. The pharmacokinetic parameters for the optimized VRD–ODTs exhibited a significant improvement with P < 0.05 in the maximum plasma concentration and reduction in the time needed to reach this concentration when compared with the marketed tablets. Finally, the optimized VRD-ODTs exhibited increased oral absorption of VRD and subsequent decreasing the time of onset of clinical effect and masking the unpleasant taste, which is favored for patients with erectile dysfunction.

Numerical calculations of ultraviolet to near-infrared absorption spectra by cadmium selenide quantum dots (CdSe QDs) doped in anodic aluminum oxide pores were performed using a finite-difference time-domain model. The height, diameter, and periodic spacing of the pores were optimized. Light absorption by the dots was enhanced by increasing the height and decreasing the diameter of the pores. When the height was less than 1 μm, visible light absorption was enhanced as the spacing was reduced from 400 nm to 100 nm. No enhancement was observed for heights greater than 6 μm. Finally, the optical mode coupling of the aluminum oxide and the quantum dots was enhanced by decreasing the pore diameter and periodic spacing, and increasing the height. Laser ablation verified light absorption enhancement by the CdSe QDs. The experiment verified the improvement of the laser-induced damage ability with wavelength of 355-nm after aluminum alloy 6061 coated with functional films, which was fabricated based on numerical calculations.

The manufacturing method influences the properties of the produced components. This work investigates the influence of manufacturing methods such as fused filament fabrication (3D printing) and injection molding on water absorption, mechanical and thermal properties of the specimens produced from neat biobased poly(lactic acid) (PLA) polymer and poly(lactic acid)/wood composites. Acrylonitrile butadiene styrene (ABS) acts as the reference material due to its low water absorption and good functional properties. The printing layer thickness is one of the factors that affects the properties of a 3D printed specimen. The investigation includes two different layer thicknesses (0.2 mm and 0.3 mm) while maintaining uniform overall thickness of the specimens across two manufacturing methods. 3D printed specimens absorb significantly higher amounts of water than the injection molded specimens, and the increase in the layer thickness of the 3D printed specimens contributes to further increased water absorption. However, the swelling due to water absorption in 3D printed specimens decreases on increased layer thickness. Tensile, flexural and impact properties of all the specimens decrease after water absorption while the properties improve on decreasing the layer thickness. Higher porosity on increasing the layer thickness is the predominant factor. The results from dynamic mechanical analysis and microscopy validate the outcomes.

The present study focuses on the development and optimization of a highly efficient unique hybrid technique — membrane-assisted gas absorption (MAGA) in designing the separation unit, which provides the improvement in mass-transfer of a target component during the natural gas processing in terms of sweetening stage. A novel design of membrane-assisted gas absorption cell is used to enhance the ratio between absorbent amount and membrane surface available for permeation. The performance tests were implemented on example of two gas mixtures separation: one is model ternary gas mixture and the second is quasi real natural gas, which includes number of hydrocarbons, nitrogen, acid impurities and xenon. For both cases, the MAGA unit demonstrated high acid gases removal efficiency, and high recovery of hydrocarbons. The ultimate efficiency of studied system was up to 96 and 61 % of removed acid gases with hydrocarbons losses up to 1 % at highest productivity. In this way, the residual sum of acid gases content may be lowered to 1 vol.% using the heat-free hybrid membrane-assisted gas absorption unit maintaining suitable recovery rate of methane, ethane, propane and n-butane. Nevertheless, the overall efficiency of the process may be enhanced using the specific absorption agents with aqueous amino alcohol solutions.

With an increasing concern for global warming, there have been many attempts to reduce greenhouse gas emissions. About 30 % of total energy has been consumed by buildings and much attention has been paid to reducing building energy consumption. While there are many ways of reducing building energy consumption, accurate energy consumption prediction becomes more significant. As mechanical systems are the most energy-consuming components in the building, the present study developed the energy consumption prediction model for a direct-fired absorption chiller by using the ANN technique for the short term. The ANN model was optimized and validated with the actual data collected through a BAS. For the optimization, the numbers of input variables and neurons, and the data size of training were applied. By changing these parameters, the predictive performance was analyzed. In sum, the outcome of the present study can used to predict the energy consumption of the chiller as well as improve the efficiency of the energy management. The outcome of the present study can be used to develop a more accurate prediction model with a few datasets in that it can improve the efficiency of building energy management.

(1) Background: Truing to find a fast and representative method for the approximate calculation of the culture density and the cell content of useful pigments, the examination of the absorption spectra of cultures of the dinoflagellate Amphidinium carterae, the haptophyte Isochrysis galbana, the chlorophyte Nephroselmis sp. and the filamentous cyanobacterium Anabaena sp. were chosen, as representative species of different taxa. (2) Methods: The experimental cultures were made in small volumes with the discontinuous method, under specific conditions each one and during the culture the absorption spectra, the density of the culture and the concentration in the pigments chlorophyll, total carotenoids and phycocyanin was recorded. (3) Results: The algal density can be quite precisely predicted as the regression equation of the correlation of the OD value of 750 nm drawn from each absorption spectrum and the measured algal biomass was very strong. The same applies also for the relevant correlations between OD 750 nm and the recorded pigments. (4) Conclusions: Absorption spectra of microalgal cultures can be an easy, low cost and non-invasive method to get the necessary information for predicting the right time to collect an ideal combination of maximum biomass and useful pigments, provided that the interpretation of the spectra is done considering that they are usefully applicable for that purpose in a case sensitive manner in terms of species and prevailing conditions.

The absolute absorption cross section of the ethyl peroxy radical, C2H5O2, in the Ã←X ̃ electronic transition with the peak wavelength at 7596 cm-1, has been determined by the method of dual wavelengths time resolved continuous wave cavity ring down spectroscopy. C2H5O2 radicals were generated from pulsed 351 nm photolysis of C2H6/Cl2 mixture in presence of O2 and detected on one of the CRDS paths. Two methods have been applied for the determination of the C2H5O2 absorption cross section: (i) based on Cl-atoms being converted alternatively to either C2H5O2 by adding C2H6 or to hydro peroxy radicals, HO2, by adding CH3OH to the mixture, whereby HO2 was reliably quantified on the second CRDS path in the 21 vibrational overtone at 6638.2 cm-1 (ii) based on the reaction of C2H5O2 with HO2, measured under either excess HO2 or under excess C2H5O2 concentration. Both methods lead to the same peak absorption cross section of C2H5O2,7596 cm-1 = (1.0±0.2) × 10-20 cm2. The rate constant for the cross reaction between of C2H5O2 and HO2 has been measured to be (6.5±1.6) × 10-12 cm3 molecule-1 s-1.

Pb found in rain water is not only caused by tin roof on houses but also caused by the pollution of industrial activities, vehicles and land clearing activity by fire. Pb pollutant dissolves and enters into rain water storages and it’s consumed as drinking. Pb can cause bad impact to human, for example disruption of enzyme, anemia and low intelligence. The purposes of this research are (1) to evaluate Pb, pH and turbidity level in rain water, (2) to analyze the effectiveness of mollusk sand filtration and the absorption of activity carbon to decrease Pb, turbidity and pH, and (3) to analyze the correlation of Pb, length of stay and smoking habit on public health. This research is an experimental by using pre and post test designs with control and observational by using cross sectional design. The research was conducted in urban and rural areas of Pontianak and Kubu Raya regency. The sampling was done in determining the number of samples of Pb, pH and turbidity in rain water. The analyzing the data by using computer program. The results show that: (1) the average of Pb, pH and turbidity level before treatment is considered high at 131.7 µg/L on Pb, turbidity at 20 NTU and low pH at 5.2. After the treatment was the Pb has decreased to 0.71 µg/L and turbidity has to 5.66 NTU, pH to 6.9 and (2) Rain water treatment is very effective to decrease Pb for 99.4% and turbidity for 72%, and (3) there is a correlation among Pb found in rain water, length of stay and smoking activity to public health. Recommends that: the residents of Pontianak and Kubu Raya to process rain water before consuming. The rain water treatment can be done by applying mollusk sand filtration and absorption of active carbon.

Prolonged high-intensity grinding can modify the crystal structure of solid substances and/or induce chemical reaction, which is referred to as mechanochemical reaction. Such reactions can exert positive influences on hydrometallurgical processes, therefore, many researchers have applied mechanochemical reactions for metals dissolution from minerals. The mechanism of mechanochemical reaction has been investigated using solid analyses and simulations. Structural changes caused by mechanochemical reaction are not yet sufficiently clarified because the ground samples are amorphous. The objective of this study was to analyze structural changes of cerianite in weathered residual rare earth ore by mechanochemical reduction. Structural change was analyzed by x-ray absorption near-edge structure and extended x-ray absorption fine structure analysis at the cerium L_III- and K-edges. These analyses revealed that the structural change of cerianite in this ore induced by mechanochemical reduction involved oxygen vacancy production. The process of the oxygen vacancy formation was closely coupled with the quantum effect of localization–delocalization of the 4f electron of cerium.

Background: A comparison of the amino acid (AA) plasma profile and markers of intestinal absorption-inflammation between healthy subjects aged 65-70 years and age-matched patients affected by stage 3b-4 chronic kidney disease (CKD3b-4) was performed. Methods: eleven healthy volunteers were compared with 12 CKD3b-4 patients at their first outpatient control (T0) and after 12-months (T12). Adherence to a low protein diet (LPD, 0.6±0.1 g/kg/day) was assessed by Urea Nitrogen Appearance. The following parameters were assessed: renal function, nutritional parameters, bioelectrical impedance analysis, plasma levels of 20 total aminoacids (TAAs), both essential (EAAs) including branched-chain amino acids (BCAAs) and non-essential (NEAAs). Zonulin and faecal Calprotectin markers were used to evaluate intestinal permeability/inflammation. Results: Four patients dropped out of the study; in the remaining 8 residual kidney function (RKF) remained stable, their LPD adherence had risen to 0.89g/kg/day, anaemia had worsened and extracellular body fluid had increased. In comparison to healthy subjects, TAA levels of histidine, arginine, asparagine, threonine, glycine, and glutamine had all increased. No variation in BCAAs was observed. A significant increase was detected in faecal calprotectin and zonulin levels in CKD patients as the disease progressed. Conclusions: This study confirms the finding in aged patients of an alteration in levels of several AAs secondary to uraemia. Intestinal markers provide confirmation of a relevant alteration to the intestinal function in CKD patients.

(1) Background: Microalgae cultures are greatly facilitated if growers can easily and economically ascertain the quantitative and qualitative status of the culture continuously with satisfactory ac-curacy. (2) Methods: The locally isolated microalgae Dunaliella sp. and Anabaena sp. were cultured in small volumes with 2 intensities of white light (2000 and 8000 lux) and with green, blue and red light and the increase of their biomass and pigments was studied. Pigment analyses, continuous recordings of absorption spectra and calibration curves were performed. (3) Results: The intensity of 8000 lux white light yielded the highest increase in biomass, chlorophylls and carotenoids in Dunaliella sp. while 2000 lux and green light caused the greatest increase in biomass and phy-cocyanin in Anabaena sp. From the examination of the absorption spectra, the evolution of the pigment content can be estimated and both pigments and biomass are correlated very satisfactorily with the wavelength of 750 nm. (4) Conclusions: The use of absorption spectra as an easy, fast and economical method can be a useful tool for a good approximation of the state of the microalgae culture. This is clearly shown when the spectra of the culture under different lighting colors are compared which have a catalytic effect on the level of the pigments leading to the increase in carotenoids and phycocyanin of the green light.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

The temporary immersion system bioreactor named GreenTray®[2], [3]presents advantages over the existing ones. Firstly, there is no need to use forceps to move the shoots or plantlets in or out of the recipient, neither the use of scalpel to divide them. Secondly, the basis of the shoot can remain in the GreenTray® and can sprout again in several cycles of growth. These two characteristics reduce the costs in the process of micropropagation. Besides, shoots or plantlets development is enhanced by the aeration of the recipient, thus enriching with CO2 the recipient atmosphere. The chapter describes and provides images and values of interest in (1) the micropropagation process of some commercial Prunus or Pyrus rootstocks; (2) the plantlet growth under autotrophic conditions; and (2) the inoculation of plants with pathogens that reproduce in vitro the symptoms observed in vivo, using the GreenTray® bioreactor.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

Apis mellifera, especially weak ones, are highly vulnerable to Carpoglyphus lactis mites, which can rapidly infest and consume stored pollen, leading to weakened colonies and potentially colony collapse. This study aimed to ascertain and investigate the prevalence of this mite in honeybee colonies across 9 provinces in the Republic of Korea (ROK). A total of 615 honeybee colonies were collected, from 66 apiaries during the spring and 58 apiaries during the summer of 2023. A 1,242 bp segment of the the Cytochrome c oxidase subunit 1 (COI) gene was amplified using the polymerase chain reaction method. The detection levels of C. lactis in the honeybees were compared between winter and summer. Based on the COI sequence analysis, the nucleotide sequence similarity of C. lactis mites isolated in the ROK with those from China (NC048990.1) was found to be 99.5%, and with those from the United Kingdom (KY922482.1) was 99.3%. This study is the first report of C. lactis in Korean apiaries. The findings in this study demonstrate a significantly higher detection rate in winter, which is 4.1 times greater than that in summer (p &lt; 0.001). Furthermore, the results underscore the usefulness of molecular diagnostic techniques for detecting C. lactis mites.

COX II containing a dual core CuA active site is one of the three core subunits of mitochondrial Cco, which plays a significant role in the physiological process. In this report, the full-length cDNA of COXⅡ gene was cloned from Sitophilus zeamais, which had an ORF of 684 bp encoding 227 amino acids residues. The predicted COXⅡ protein had a molecular mass of 26.2 kDa with pI value of 6.37, and multiple sequence alignment and phylogenetic analysis indicated that Sitophilus zeamais COXⅡ had high sequence identity 78.51% with the COXⅡ of other insect species, especially similarity to sitophilus oryzae. This gene was subcloned into the prokaryotic expression vector pET-32a, and induced by IPTG in E.coli Transetta (DE3) expression system. Finally the COXⅡ with 6-His tag was purified using affinity chromatography with Ni²⁺-NTA agarose. WB showed the recombinant COXⅡ was about 44 kD, and the concentration of fusion protein was 50μg/mL. UV-spectrophotometer and infrared spectrometer analysis showed that recombinant COXⅡ could catalyze the oxidation of substrate Cytc, and influenced by AITC. It was found that AITC could form a hydrophobic region with COXⅡ protein via molecular docking, besides, a sulfur atom of AITC structure could form a length of 2.9 Å hydrogen bond with Leu-31. These results will provide valuable information for elucidating the role of COXⅡ in Sitophilus zeamais responses to AITC, meanwhile, it will helpful to carry out a point mutation in AITC binding sites for the future research.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

Our skin epidermis constitutes the most important innate defense barrier against all pathogens. Therefore, even if skin lesions are common due to infections, scarring, genetic disorders, and other diseases, skin integrity is crucial for maintaining body homeostasis. Marine collagen peptides (MCPs) and Glycosaminoglycans (GAGs) have been described as potential wound healing (WH) agents. Recently, through an ex vivo clinical approach, we have demonstrated the nutricosmetic potential of fish cartilage hydrolysate (FCH), which presents a combination of collagen peptides and GAGs. Here, we coupled a clinical approach with in vitro experiments on human dermal fibroblasts (HDFs) and applied a Data Independent Acquisition - Parallel Accumulation Serial Fragmentation (diaPASEF) proteomic analysis, to assess the potential benefit of FCH in WH and its mode of action. Our results show that human serum enriched with circulating metabolites resulting from FCH ingestion, improved wound closure in scratch assays. In support, some proteins with anti-inflammatory and immunomodulatory properties or prone to promote hydration and extracellular matrix (ECM) stability showed increased expression in HDFs, after exposure to FCH-enriched serum. These findings suggest that FCH appears as a promising nutrient for WH and skin regeneration.

This paper is focused on typical rural settlements in the Stara Planina Mountain area in Serbia. They are distinguished by their authenticity, identity and character, and they have still not been destroyed by inappropriate development as is the case in some other mountain areas in Serbia, where the effects of urbanization, globalization and homogenization are obvious. Consequently, there is a need to prevent these effects in mountain areas where there is a threat of disbalance between development and the inherited natural and cultural values. The paper starts from several important concepts that relate contemporary approaches to cultural heritage preservation, place morphology and planning future development. The concept definitions from recent documents from related fields are used. These concepts are then applied to the area of Stara Planina Mountain and its rural settlements. The necessity for an integrative approach to planning this area with significant natural and anthropogenic potential is pointed out, including its integration into international programs of sustainable development.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

Promoting green development has become an important way to optimize the ecological and economic structure and promote sustainable development. The Yangtze River Economic Belt is an important economic corridor in China, and it remains to be examined whether the implementation of environmental regulations has enhanced the green total factor productivity (GTFP) of cities. This paper calculates the green total factor productivity of 107 cities within the Yangtze River Economic Belt by using the super-efficient SBM model and the GML index with Chinese city panel data from 2007-2019 and measures the intensity of environmental regulations through textual analysis. The bidirectional fixed-effects model constructed in this paper suggests an inverted U-shaped relationship between environmental regulation and GTFP, which is confirmed by a series of robustness tests. Green technology innovation and advanced industrial structure play a mechanism role in this. In regions with lower levels of green technology and industrial structure, the inverted U-shaped relationship between environmental regulation and green total factor productivity is more significant. In addition, the phenomenon of GTFP rising and then falling because of environmental regulation is more obvious in cities in the middle and upper reaches of the Yangtze River and outside the urban agglomerations. Therefore, when formulating environmental regulation policies, it is necessary to balance the relationship between economic development and environmental protection and harmonize the environment and economic development of the entire Yangtze River Basin.

The wetlands in northeastern Bangladesh are home to some of the most prolific and valuable ecosystems on the planet, offering a wide range of benefits to both the local and wider communities. A limited number of research on this topic have been carried out in various wetlands in coastal hilsa, but none have been located in the northeastern region of Bangladesh. Thus, the goal of this study was to better understand the most commercially relevant species (anadromous hilsa) in northeastern Bangladesh as well as to assess the wetland ecosystem services more thoroughly with the contribution of their fish genetic resources. In addition to laboratory studies, fieldwork was done in the fishing settlements along the Surma River, Hakaluki Haor, and Tanguar Haor. The study classified 77 fish species into 21 subcategories of ecosystem services, of which 56% were not threatened, 17% were vulnerable, and 10% were highly endangered. The species Hilsa was found to be the most economically significant, accounting for 1% of the GDP overall. The study determined if the hilsa stock of the examined wetlands maintains a single or several subpopulations in comparison to other parts of the country when they migrate from saline water to northeastern Bangladesh (freshwater). But when compared to other groups, the FST score was between 0.000 to 0.017, indicating that the populations are identical and that there is genetic material sharing between them. Additionally, these statistics imply that the Sylhet haor and adjacent river systems contain a single stock of Hilsa fish. Nevertheless, a number of stresses and risks, including overexploitation, illicit and destructive fishing, siltation, and natural disasters like flash floods, have been linked to changes in the supply of hilsa and other ecosystem services. This study also emphasizes the necessity of policy attention and research to address the concerns.