The decarbonization of the built environment, both in new construction and renovation, is crucial to mitigate its relevant impact on climate change and achieve the Paris agreement goals. This study presents a systematic LCA-based methodology to assess the whole life carbon emissions of buildings, applied to a proposal for the regeneration of one of Milan’s disused railway yards. As an entry for the 2020 Reinventing Cities competition, Scalo Lambrate is a project for a mainly residential neighborhood with a public park. Strategies to reduce carbon emissions deriving both from the operational energy and construction and maintenance were evaluated and their effects compared to a reference scenario over a time horizon of 100 years. The results show that, while the opportunities to reduce carbon emissions during the use phase are somehow limited due to the already stringent performance requirements for new builds, the use of fast-growing biogenic materials for construction materials, even if mixed with more traditional ones, can provide a significant reduction of the global warming potential over the whole life cycle, with a reduction of 70% over the baseline. The remaining emissions can be offset with afforestation initiatives that, however, must be assessed against land use issues.

Introduction: maxillary hypoplasia and mandibular asymmetry may be corrected with orthognathic surgery at the completion of growth. Many patients require segmental Le Fort I osteotomies to obtain the most stable results. Unfortunately, if Invisalign is chosen for pre-surgical preparation, ClinCheck © software does not allow for prediction when these complex surgeries are planned. The objective of this paper was to show the potential of aligners beyond its software in most complex cases like multiple-piece maxillary osteotomies in cleft and non-cleft patients. Method: Thirteen patients who underwent pre-surgical treatment with clear aligners-Invisalign (study group) were matched in terms of diagnosis, surgical procedure, and orthodontic complexity with thirteen patients treated using fixed appliances (control group). A technique based on simple superimposition was devised to enhance the software for creating a suitable occlusion for segmental pre-surgical treatments. Virtual curves following the lower arch were employed to guide the correct pre-surgical positions of the upper teeth. The amount of impressions required in both groups to achieve satisfactory pre-surgical alignment of the segmented arches was compared. Results: one or no refinement phase were needed in the Invisalign group to reach an acceptable pre-surgical occlusion while the amount of pre-surgical impressions taken in order to reach adequate coordination with fixed appliance treatment was slightly higher. The average overall treatment duration did not show a statistically significant variation between the groups. Conclusions: it appears that clear aligner could serve as an effective treatment for individuals with skeletal discrepancies, including cleft and craniofacial anomalies, necessitating segmental Le Fort I osteotomies when aided by the suggested superimposition approach during digital pre-surgical movement simulations. More sophisticated softwares will certainly be implemented in the future.

The application of space robotic manipulators and heightened autonomy for ios represents a paramount pursuit for leading space agencies, given the substantial threat posed by space debris to operational satellites and forthcoming space endeavors. This work presents a guidance algorithm based on drl to solve for the space manipulator path-planning during the motion synchronization phase with the mission target. The goal is the trajectory generation and control of a spacecraft equipped with a 7-dof robotic manipulator, such that its end effector remains stationary with respect to the target point of capture. The ppo drl algorithm is used to optimize the manipulator’s guidance law, and the autonomous agent generates the desired joints rates of the robotic arm, which are then integrated and passed to a model-based feedback linearization controller. The agent is first trained to optimize its guidance policy and then tested extensively to validate the results against a simulated environment representing the motion synchronization scenario of an ios mission.

Radio loud active galactic nuclei are composed of different spatial features, each one characterized by different spectral properties in the radio band. Among them, blazars are the most common class of sources detected at gamma-rays by \fermi, and their radio emission is dominated by the flat spectrum compact core. In this contribution, we explore the connection between emission at high energy revealed by \fermi\ and at radio frequency. Taking as a reference the strong and very highly significant correlation found between gamma rays and cm-$\lambda$ radio emission, we explore different behaviours found as we change the energy range in gamma rays and in radio, therefore changing the physical parameters of the zones involved in the radiation emission. We find that the correlation weakens when we consider (1) gamma rays of energy above 10 GeV (except for high synchrotron peaked blazars) or (2) low frequency radio data taken by the Murchison Widefield Array; on the other hand, the correlation strengthens when we consider mm-$\lambda$ data taken by ALMA.

An experimental study is carried out in a cavitation tunnel on a propeller operating downstream of a non-uniform wake. The goal of this work is to establish quantitative correlations between the near pressure field and the cavitation pattern that takes place on the propeller blades. The pressure field is measured at the walls of the test section and in the near wake of the propeller, and is combined with quantitative high-speed image recording of the cavitation pattern. Through simple harmonic analysis of the pressure data and image processing techniques that allow to retrieve the cavitation extension and volume, we discuss the potential sources that generate the pressure fluctuations. Time correlations are unambiguously established between pressure peak fluctuations and cavitation collapse events, based upon the Rayleigh collapse time. Finally, we design a model to predict the cavitation-induced pressure fluctuations from the derivation of the cavitation volume acceleration. This simple model demonstrates a remarkable agreement with the actual pressure field.

Cardiovascular disease (CVD) is the leading cause of death worldwide. Cardiac rehabilitation (CR) has proven to be effective in reducing the rate of recurrence and disease as secondary prevention (evidence-based intervention) in patients who have suffered from myocardial infarction (MI). CR is a multidisciplinary path in which the patient is followed pharmacologically, from a psychological, nutritional, nursing and physiotherapy point of view. Post-MI patients present a reduction in the performance of the diaphragm muscle, the main inspiratory muscle, and this condition can become a risk factor for further relapses or for the onset of heart failure. Despite the solidity of the international guidelines for CR, the latter are lacking in specifically indicating an evaluation and training path regarding the inspiratory muscles in post-MI patients who have not undergone cardiac surgery. The article reviews the information on the adaptation of the diaphragm post-MI and highlights the need for clearer indications for a rehabilitation process that gives importance to the diaphragm.

The “circular bioeconomy” offers numerous opportunities for the health, cosmetic, and nutrition sectors through the potential reuse of Castanea sativa by-products. This abundant and sustainable resource provides valuable bioactive secondary metabolites with antioxidants and anti-inflammatory properties. The transformation of these by-products into high-value products for human health can contribute to sustainable economic growth and reduce the environmental impact of traditional waste disposal practices, thus creating added value from previously underutilized resources. In the present study, we investigated the antioxidant capacity, phytochemical composition and in vitro antioxidant and anti-inflammatory activity of C. sativa burrs (CSB) aqueous extract. The spectrophotometric study yielded optimal total phenolic content (TPC) values, along with significant antioxidant and anti-radical properties. The utilization of UPLC-MS-MS techniques for phytochemical investigation resulted in the identification of a total of 56 metabolites, providing confirmation of the presence of phenolic compounds in CSB. In addition, CSB significantly downregulated pro-inflammatory mediators in LPS-stimulated RAW 264.7 macrophage cells without significant cell toxicity.

Knowledge is not merely the characteristic of certain pieces of information being deemed true and justifiable, but rather a process. Within an axiomatic system, the set of information that reaches the status of knowledge forms a universe that provides an interpretation of the reality one aims to describe. Language exchanges information through communication and the process of justification (exchange of information), if it consistently justifies a particular piece of information, it elevates it to knowledge. In this paper, we provide a framework for knowledge within an axiomatic model where we define the fundamental elements of communication and grammar. As a result, the structure dictates that knowledge, to be considered as such, must be investigateable by anyone who utilizes it in its entirety, both in form and content. Ultimately, the development of knowledge processing, referred to as \emph{knowmatics}, represents a clear evolution of the computer science that processes information (subset of knowledge).

PVC items are environmentally friendly as, unlike polyolefins, they are mainly based on chlorine, one of the most abundant elements on earth. However, in the eco-design context, articles' durability plays the crucial role, contributing to the enhancement of their sustainability. In this framework the research on additives capable of increasing the weatherability of outdoor articles is essential. The theory section of the paper reviews the mechanisms of weathering leading to PVC degradation that undermine the durability of items such as window frames or roller shutters. The weathering of PVC items is a complex phenomenon involving photo-chemical and secondary chemical reactions, that yields the formation of conjugated polyene sequences underskin in absence of oxygen and carbonyls in the surface. Here the chain scission of the polymer backbone occurs, bringing the disintegration of the surface of the item and causing the typical discoloration called chalking, especially evident in dark-colored articles. In the experimental section of the paper the effect of different acid scavengers on the item weathering has been studied with natural outdoor and two accelerated exposures, xenon-arc and Q-UV testing devices. Results confirm that some acid scavengers are efficient in preventing chalking, but some are ineffective or even detrimental. Thus, the PVC formulations of durable articles upon weathering still depend on a complex choice of the appropriate ingredients, and several outdoor and indoor accelerated weathering tests are needed to predict the articles' lifetime.

The rationalization of single molecule magnets’ (SMMs) magnetic properties by quantum mechanical approaches represents a major task in the field of the Molecular Magnetism. The fundamental interpretative key of molecular magnetism is the phenomenological Spin Hamiltonian and the understanding of the role of its different terms by electronic structure calculations is expected to steer the rational design of new and more performing SMMs. This paper deals with the ab initio calculation of isotropic and anisotropic exchange contributions in the Fe(III) dimer [Fe₂(OCH₃)₂(dbm)₄]. This system represents the building block of one of the most studied Single Molecule Magnets ([Fe₄RC(CH₂O)₃)₂(dpm)₆] where R can be an aliphatic chain or a phenyl group just to name the most common functionalization groups) and its relatively reduced size allows the use of a high computational level of theory. Calculations were performed using CASSCF and NEVPT2 approaches on the X-ray geometry as assessment of the computational protocol, which has then be used to evinced the importance of the outer coordination shell nature through organic ligand modelization. Magneto-structural correlations as function of internal degrees of freedom for isotropic and anisotropic exchange contributions are also presented, outlining for the first time the extremely rapidly changing nature of the anisotropic exchange coupling.

The term Conjugated Linoleic Acid (CLA) refers generically to a class of positional and geometric conjugated dienoic isomers of linoleic acid. Among the isomers of linoleic acid cis9, trans11-CLA (c9, t11-CLA) and trans10, cis12-CLA (t10, c12-CLA) are found to be bio-logically active isomers, and they occur naturally in milk, dairy products and meat from ruminants. In addition, some vegetables and some sea-foods have also been reported to contain CLA. Although the CLA levels in these natural sources are insufficient to confer the essential health benefits, anti-carcinogenic or anti-cancer effects are of current interest. In the rumen, CLA is an intermediate of isomerization and the biohydrogenation process of linoleic acid to stearic acid conducted by ruminal microorganisms. In addition to rumen bacteria, some other bacteria, such as Propionibacterium, Bifidobacterium and some lactic acid bacteria (LAB) are also capable of producing CLA. In this regard, Lactiplantibacillus plantarum (formerly Lactobacillus plantarum) has demon-strated the ability to produce CLA isomers from linoleic acid by multiple enzymatic activi-ties, including hydration, dehydration, and isomerization. L. plantarum is one of the most versatile species of LAB and the bacterium is widely used in the food industry as a micro-bial food culture. The studies reviewed in this article reveal how, in the production of some fermented foods, the use of appropriate strains of L. plantarum, as a starter or additional culture, can be considered a critical factor in the design of new CLA-enriched functional foods.

Industries, which are mainly responsible for high energy consumptions, need to invest in research projects in order to develop new managing systems for rational energy use and to tackle the devastating effects of climate change caused by human behavior. The study reported in this paper concerns the forging industry, where the production processes generally start with the heating of the steel in furnaces and continue with other processes, such as heat treatments and mechanical machining. One of the most critical operations, in terms of energy loss, is the opening of the furnace doors for the insertion and extraction operations. During this time, the temperature of the furnaces decreases by hundreds of degrees in a few minutes. Because the dispersed heat needs to be supplied again through the combustion of fuel, increasing the consumption of energy and the pollutant emissions, the evaluation of the amount of the lost energy is crucial for the development of operating or mechanical systems able to contain this dispersion. To perform this study, CFD simulation software was used. Results show that at the door opening, because of temperature and pressure differences between the furnace and the ambient, turbulences are generated. Results also show that the amount of energy lost for an opening of 10 minutes for radiation, convection and conduction is equal to 5606 MJ where convection is the main contributor with 5020 MJ. The model created, after being validated, has been applied to perform other simulations in order to improve the energy performance of the furnace. Results show that a reduction of the opening time of the door allows energy savings and limits pollutant emissions.

Black soldier fly larvae (BSFL) can use food by-products or residues as a growth substrate, and their use is considered a strategic solution to improve the sustainability and efficiency of animal production. BSFL need to be reared under controlled environmental conditions, as temperature can affect the welfare of the larvae and the efficiency of their bioconversion. The goal of this experiment was to test different diets: control, vegetable, carnivorous, omnivorous and to assess their effect on larval growth performance, chemical composition, and substrate temperature. BSFL (6-days-old) were randomly selected and allocated to one of the four diets for the entire experiment (8 days). The temperature in each container was measured twice daily using a thermal imaging camera. The vegetable diet led to significantly lower growth performance (p

Treatment wetlands (TWs) are Nature-Based Solutions increasingly used worldwide for wastewater (WW) treatment able to remove mineral and organic pollutants through both physical and biochemical process. Besides the reusable effluent, the TWs produce as main output plant biomass that need to be harvested and disposed at least once a year with significant management costs and TW temporary out of service. This study aims (i) to evaluate the potential of TWs biomass for local energy production and (ii) to understand TW hydraulic conductivity (Ks) effects on the biomass biomethane yield. Specifically, it was addressed by determining the Biochemical Methane Potential of common reed (CR) (Phragmites australis) samples collected at three harvest times from the 10-years-old horizontal subsurface treatment wetland (HSTW) used as a secondary WW treatment system for the IKEA® store located in Catania (Eastern Sicily, Italy). Furthermore, the falling head test was conducted to assess the hydraulic conductivity (Ks) variation in the HSTW, in order to understand the influence on the CR biomethane production. Average methane content values were 130.57 Nm3CH4/tVS (±24.29), 212.70 Nm3CH4/tVS (±50.62) and 72.83 Nm3CH4/tVS (±23.19) in August, September, October 2022, respectively. Ks was correlated with both dry matter (R2 = 0.58) and fiber content (R2 = 0.74) and, consequently, affected the biomethane yield that increased at the Ks increases (R2 = 0.30 in August, R2 = 0.57 in September). In the framework of a circular economy, results showed the successfully possibility of integrating the bioenergy production into TWs. The research could contribute (i) to encourage plant operators to reuse biomass from TWs for local energy production and (ii) to help plant operators to understand Ks effects on the biomass biomethane yield, in order to increase the sustainability of the system and to reduce the maintenance costs.

Background: The surgical approach to treating calcaneal fractures, specifically Sanders types II, III, and IV, is still a subject of controversy. The decision to opt for open reduction and internal fix-ation (ORIF) or minimally invasive osteosynthesis (MIOS) remains uncertain owing to varying complication rates. This study intends to examine each treatment’s pros and cons in relation to the incidence of complications. Methods: In this retrospective study, we examined 70 patients treated between January 2018 and September 2022: 50 received ORIF, and 20 underwent MIOS. We evaluated functional outcomes with the Maryland Foot Score and the Creighton-Nebraska Health Foundation Assessment Scale (CNHFAS). We also assessed the amount of anatomical restoration using Böhler’s and Gissane’s angles, determined by radiographic checks, and the frequency of postoperative complications. Results: A significant reduction in the risk of reinter-vention was observed in patients with high anesthetic risks, polytraumatized individuals, and those with comorbidities who underwent MIOS. The chi-square test analysis of postoperative complications highlighted no substantial differences between the ORIF and MIOS groups in rela-tion to tendinitis, chronic pain and swelling, algodystrophy, and surgical wound infections (p > 0.20 for all). Conclusion: ORIF is more suitable for patients who have high motor function re-quirements, a long-term activity schedule and can endure potential additional procedures. This preference is because ORIF provides better anatomical restoration and features a lower osteoar-thritis occurrence rate.

This paper explores the application of Random Matrix Theory (RMT) as a methodological enhancement for portfolio selection within financial markets. Traditional approaches to portfolio optimization often rely on historical estimates of correlation matrices, particularly susceptible to instability. To address this challenge, we combine a data preprocessing technique based on the Hilbert transformation of returns with RMT to refine the accuracy and robustness of correlation matrix estimation. By contrasting empirical correlations with those derived from random matrices, we uncover non-random properties and underlying relationships within financial data. We then utilize this methodology to construct the correlation network dependence structure used in portfolio optimization. The empirical analysis presented in this paper validates the effectiveness of RMT in enhancing portfolio diversification and risk management strategies. This research contributes by offering investors and portfolio managers with methodological insights to construct portfolios that are more stable, robust, and diversified. At the same time, it advances our comprehension of the intricate statistical principles underlying multivariate financial data.

The discovery by the Large Area Telescope on board Fermi of variable gamma-ray emission from radio-loud narrow-line Seyfert 1 (NLSy1) galaxies revealed the presence of a possible third class of AGN with relativistic jets in addition to blazars and radio galaxies. Considering that NLSy1 are usually hosted in spiral galaxies, this finding poses intriguing questions about the nature of these objects and the formation of relativistic jets. We report on a systematic investigation of the gamma-ray properties of a sample of radio-loud NLSy1, including the detection of new objects, using 7 years of Fermi-LAT data with the new Pass 8 event-level analysis. In addition we discuss the radio-to-very-high-energy properties of the gamma-ray emitting NLSy1, their host galaxy, and black hole mass in the context of the blazar scenario and the unification of relativistic jets at different scales.

Background: this interventional pilot study aimed to evaluate the short-term (3 years) efficacy of focal laser ablation (FLA) in treating the index lesion of low-intermediate risk prostate cancer, along with assessing the safety of the procedure (ClinicalTrials.gov ID NCT04045756). Methods: forty patients aged between 46 and 86 with histologically proven organ-confined prostate cancer and low to intermediate progression risk were included. FLA was performed under percutaneous fusion magnetic resonance/ultrasound guidance in a Day Hospital setting under local anesthesia. Patients underwent regular clinical assessments, PSA measurements, post-procedure MRI scans, and biopsies at 36 months or if positive findings were detected earlier. Statistical analyses were conducted to assess trends in PSA levels and cavity dimensions over time. Results: forty patients were initially included, with 15 lost to follow-up. At 36 months, a mean PSA reduction of 60% was observed, and 80% of MRI scans showed no signs of in-field clinically significant residual/recurrent cancer. Biopsies at 36 months revealed no malignant findings in 20 patients. No deterioration in sexual function or urinary symptoms was recorded. Conclusions: FLA appears to be safe, feasible and effective in the index lesion treatment of low-intermediate risk prostate cancer, with a high rate of tumor eradication and preservation of quality of life.

Childhood emotional abuse (CEA) has been linked to a range of unfavorable outcomes, including the development of unhealthy personality traits and maladaptive coping mechanisms and behaviors. In this study, our objective was to investigate whether neuroticism and perfectionism act as mediators in the relationship between CEA and workaholism, while also evaluating the gender invariance of the hypothesized model. A cohort of 1176 young workers, with a balanced gender representation (50% female), aged 18-25, participated in the study by completing self-report questionnaires. The results revealed significant connections between all direct and indirect links, indicating a complex interplay between childhood emotional abuse, neuroticism, perfectionism, and workaholism. Importantly, the mediation model exhibited no significant differences between genders, suggesting that the identified relationships are consistent across both male and female participants. This research underscores the critical importance of early identification of childhood emotional abuse and advocates for the implementation of trauma-informed care to address the negative consequences of emotional abuse, ultimately aiming to prevent the development of workaholism. Furthermore, the findings emphasize the necessity for tailored prevention strategies, focusing on mitigating neuroticism and perfectionism as potential pathways for effective therapeutic interventions.

We consider a constrained optimal control problem and an extension of it, in which the set of strict-sense trajectories is enlarged. Extension is a common procedure in optimal control, used to derive necessary and sufficient optimality conditions for the original problem from the extended one, which usually admits a minimizer and has a more regular structure. However, this procedure fails if the two problems have different infima. It is therefore relevant to identify such situations. Following on from earlier work by Warga but adopting perturbation techniques developed in non-smooth analysis, we investigate the relation between the occurrence of an infimum gap and abnormality of necessary conditions. For a notion of local minimizer based on control distance and an extension including the impulsive one, we prove that (i) a local extended minimizer which is not a local minimizer of the original problem and (ii) a local strict-sense minimizer which is not a local minimizer of the extended problem, both satisfy the extended maximum principle in abnormal form. The main novelty is result (ii), as until now it had only been shown that a strict-sense minimizer which is not an extended minimizer is abnormal for an `averaged version’ of the maximum principle.

High redshift blazars are among the most powerful objects in the Universe. Although they represent a significant fraction of the extragalactic hard X-ray sky, they are not commonly detected in gamma-rays. High redshift (z>2) objects represent <10 per cent of the AGN population observed by Fermi so far, and gamma-ray flaring activity from these sources is even more uncommon. The characterization of the radio-to-gamma-ray properties of high redshift blazars represents a powerful tool for the study of the energetics of such extreme objects and the Extragalactic Background Light. This contribution will present results of multi-band campaigns, from radio to gamma-rays, on PKS 0836+710, PKS 2149-306, and TXS 0536+145. The latter is the highest redshift detection of a flaring gamma-ray blazar so far. At the peaks of their respective flares these sources reached an apparent isotropic gamma-ray luminosity of about 10^50 erg/s, which is comparable with the luminosity observed from the most powerful blazars. The physical properties derived from the multi-wavelength observations of these sources are then compared with those shown by the high redshift population.

The synthesis of a new class of epoxide derivatives from prochiral vinylidene bisphosphonate (VBP) precursors is reported using hydrogen peroxide as the terminal oxidant. The reaction is carried out using a series of possible organic catalysts having a basic character, the best results being observed using quinine and sparteine. These catalysts not only provide from good to excellent epoxide yields with a large variety of VBPs but also interesting enantioselectivities in the 67-96% ee range at least in the case of the Ph and m-MeO-Ph VBP derivatives opening the way to a number of chiral anti-osteoporosis potentially active pharmaceutical ingredients.

Biopolymers are of growing interest, but to improve some of their poor properties and performance, it is required the formulation of bio-based blends and/or adding of nanoparticles. For this purpose, in this work, two different metal oxides, such as zinc oxide (ZnO) and titanium dioxide (TiO2), at different concentrations (0.5, 1 and 2 %wt.) have been added in polylactic acid (PLA) and polylactic acid/polyamide 11 (PLA/PA11) blends to establish their effects on solid-state properties, morphology, melt behaviour, and photo-oxidation resistance. It seems that the addition of ZnO in PLA leads to a significant reduction of its rigidity probably due to an inefficient dispersion in the melt state, while the addition of TiO2 does not penalise PLA rigidity. Interestingly, the addition of both ZnO and TiO2 in PLA/PA11 blend has a positive effect on the rigidity because of blend morphology refinement and leads to a slight increase in film hydrophobicity. The photo-oxidation resistance of neat PLA and PLA/PA11 blend is significantly reduced due to the presence of both metal oxides, and this must be considered when designing the potential applications. The last results suggest that both metal oxides could be considered as photo-sensitive degradant agents for biopolymer and biopolymer blends.

The nickel-chromium-molybdenum alloy 625 exhibits an excellent combination of mechanical properties and corrosion resistance. However, the high temperature plastic deformation process and the heat treatment represent critical aspects and the adoption of non-optimal parameters can result in excessive grain coarsening and loss in mechanical strength. This detrimental behavior is worsened by the presence of a narrow region of temperatures and strain rates for complete recrystallization and the absence of phase transformation temperatures. In this alloy, the presence of sufficient amounts of niobium, titanium and aluminum permits slow age-hardening response upon single-aging treatments. Therefore, when the soft- or solution-annealed condition is associated with insufficient mechanical properties, this potentiality can be exploited to improve the mechanical strength and prevent waste of material and resources. Since the precipitation kinetic of the hardening γ^'' phase can be accelerated by prior nucleation treatment, different time-temperature combinations of double aging at 732 °C and 621 °C are investigated to reduce the overall heat treatment time. However, the simultaneous formation of Cr-rich carbides can dramatically affect the intergranular corrosion resistance. For this reason, a performance map is developed to compare all the tested conditions and identify the best compromise in terms of mechanical strength and corrosion rate.

The study of rare diseases is important not only for the individuals affected but also for the advancement of medical knowledge and a deeper understanding of human biology and genetics. The wide repertoire of structural information now available from reliable and accurate prediction methods provides the opportunity to investigate the molecular origins of most of the rare diseases reviewed in the Orpha.net database. Thus, it has been possible to analyze the topology of the missense mutations found in the 2,535 proteins involved in Mendelian rare diseases (MRD), which form the database for our structural bioinformatics study. The amino acid substitutions responsible for MRD show different mutation site distributions at different three-dimensional protein depths. We then predicted the depth-dependent effects of mutations for the 20,248 pathogenic variants that are present in our database. The results of this structural bioinformatics investigation are relevant, as they provide additional clues to mitigate the damage caused by MRD.

This work is aimed at investigating the capabilities and limits of the mid-fidelity numerical solver DUST for the evaluation of wind turbines aerodynamic performance. In particular, this study was conducted by analysing the benchmarks NREL- 5MW and Phase VI wind turbines, widely investigated in literature by from experimental and numerical activities. The work started by simulating simpler configuration of the NREL- 5MW turbine to progressively integrate complexities such as shaft tilt, cone effects and yawed inflow conditions, offering a detailed portrayal of their collective impact on turbine performance. A particular focus was then given to the evaluation of aerodynamic responses from the tower and nacelle, as well as aerodynamic behavior in yawed inflow condition, crucial for optimizing farm layouts. In the second phase, the work was focused on NREL Phase VI turbine due to the availability of experimental data on this benchmark case. Comparison of DUST simulations results with both experimental data and high-fidelity CFD tools shows the robustness and adaptability of this mid-fidelity solver for this applications, thus opening a new scenario for the use of such mid-fidelity tools for the preliminary design of novel wind turbines configurations or complex environments as wind farms, characterised by robust interactional aerodynamics.

This study addresses the urgent need for sustainable protein sources in aquaculture due to the depletion of marine resources and rising costs. Animal protein sources, particularly poultry by-product meal (PBM) and insect exuviae meal, are investigated as viable alternatives to fishmeal (FM). Research confirms the successful replacement of FM with a combination of PBM and insect exuviae meal (up to 50%) in the diet of European seabass without compromising growth, feed conversion, gut health and liver fat content. In particular, growth performance was robust with both PBM formulations, with the 25% PBM diet showing better results. Histological examinations showed good gut and liver health, contradicting the concerns of previous studies. The study emphasizes the importance of holistic analyzes that go beyond growth parameters and include histomorphological investigations. The results show that PBM in combination with insect/exuviae meal is well tolerated by seabass, which is consistent with literature reports of mitigating negative effects on gut health. A detailed analysis of the microbiota revealed a decrease in the Firmicutes/Proteobacteria ratio due to an increase in potentially pathogenic bacteria. However, the formulation containing insect exuviae partially counteracted this effect by preserving the beneficial Lactobacillus and promoting the synthesis of short-chain fatty acids (SCFA), particularly butyrate. Chitin-rich components from insect exuviae were associated with improved gut health, which was supported by increased production of SCFA, which are known for their anti-inflammatory properties. The study concludes that a combination of PBM and insect/exuviae meal can replace up to 50% of FM in the diet of seabass, supporting sustainable aquaculture practices. Despite some changes in the microbiota, the negative effects are mitigated by the addition of insect exuviae, highlighting their potential as a prebiotic to increase fish productivity and contribute to a circular economy in aquaculture.

Heart failure (HF) management in type 1 diabetes (T1D) is particularly challenging due to its increased prevalence and the associated risks of hospitalization and mortality, driven by diabetic cardiomyopathy. Sodium-glucose cotransporter-2 inhibitors (SGLT2-i) offer a promising avenue for treating HF, specifically the preserved ejection fraction variant most common in T1D, but their utility is hampered by the risk of euglycemic diabetic ketoacidosis (DKA). This review investigates the potential of SGLT2-i in T1D HF management, alongside the emergent Continuous Ketone Monitoring (CKM) technology as a means to mitigate DKA risk, through a comprehensive analysis of clinical trials, observational studies, and reviews. The evidence suggests SGLT2-i significantly reduce HF hospitalization and enhance cardiovascular outcomes. However, their application in T1D patients remains limited due to DKA concerns. CKM technology emerges as a crucial tool in this context, offering real-time monitoring of ketone levels, which enables the safe incorporation of SGLT2-i into treatment regimes by allowing for early detection and intervention in the development of ketosis. The synergy between SGLT2-i and CKM has the potential to revolutionize HF treatment in T1D, promising improved patient safety, quality of life, and reduced HF-related morbidity and mortality. Future research should aim at clinical trials directly assessing this integrated approach, potentially guiding new management protocols for HF in T1D.

Structural deformations are one of the most significant factor that affects machine tool (MT) positioning accuracy. These induced errors are complex to be represented by a model, nevertheless they need to be evaluated and predicted in order to increase the machining performance. This paper presents a novel approach to calibrate a machine tool in real-time, analyzing the thermo-mechanical errors through Fibre Bragg Grating (FBG) sensors embedded in the MT frame. The proposed configuration consists of an adaptronic structure of passive materials, Carbon Fibre Reinforced Polymers (CFRP), equipped by FBG sensors that are able to measure in real-time the deformed conditions of the frame. By using a proper thermo-mechanical kinematic model, the displacement of the end effector may be predicted and corrected when it is subjected to external undesired factors. By starting from a set of FE simulations to develop a model able to describe the MT structure stresses, a prototype has been fabricated and tested. The scope was to compare the numerical model with the experimental tests using FBG sensors. The experimental campaign has been performed varying the structure temperature over time and measuring the tool tip point (TTP) positions. The obtained results showed a substantial matching between the real and the predicted position of TTP confirming the effectiveness of the proposed calibration system.

The Italian herbal products market is the most prosperous in Europe. The proof is represented by the use of these products in several marketing categories, ranging from medicine to nutrition and cosmetics. Market and legislation in Italy are at the same time cause and consequence of this peculiar situation. In fact, the legislation on botanical food supplements in Italy is very permissive and at the same time the market shows an overall satisfaction of users and strong feedback in terms of consumption, which brings a widening use of medicinal plants, formerly the prerogative of pharmaceuticals, to other fields such as nutrition. This review summarizes the market and normative panorama of herbal products in Italy, highlighting the blurred boundaries of health indications, marketing authorizations and quality controls between herbal medicines and non pharmaceutical products, such as food supplements, cosmetics and other herbal-based “parapharmaceuticals”.

The carbohydrate antigen Sda is expressed on cells and secretions of the vast majority of Caucasians. The epitope is formed by a terminal GalNAc residue β4-linked to a α3-sialylated galactose. Different carbohydrate chains N- or O-linked to glycoproteins can be terminated by this epitope. The final step of Sda biosynthesis is catalyzed by the GalNAc transferase B4GALNT2. In this review, we will discuss the multifaceted aspects of B4GALNT2/Sda biology. In particular, we will see its implications in fertility and pregnancy, in susceptibility to infectious diseases, in chronic kidney diseases and in Duchene muscular dystrophy. In particular, we will show its regulation and prognostic implications in cancer.

Reducing the levels of toxic chemicals that cause adverse health and environmental impacts is a challenge for the international community. There is a need of a global strategy. Indeed, too often the problems associated to the exposure of chemical substances is recognized a posteriori, in the presence of consequences already observed. The prediction of the likely effects of chemical exposure on human health is based on classical tests with animals, which are time and money consuming, may deviate from an accurate prediction towards humans, and arises ethical concerns. Regulations are now considering the adoption of in silico (or computational) methods, which can be used for prioritizing substances according to the probability to be toxic for the biosphere. Several initiatives have prioritized chemicals, typically based according to some criteria, such as chemicals which may be endocrine disruptors, or persistent, bioaccumulative, or toxic (PBT). However, these initiatives focused on a certain range of adverse properties, and covered a certain number of substances only. We applied a set of largely validated and widely used predictive methods to large collections of chemicals: (i) to about 340,000 with a defined function, and (ii) to about 6 millions, which have been synthetized. The aim of this study is to quantify the putative impact of existing and future chemicals on towards human health, ecological and environment properties. The impact on the environment is the cause of major concern. This is the case of pesticides and hazardous, which is quite expected; however, also pharmacologically active candidate compounds of natural origin may have a high level of ecotoxicity. Pesticides and hazardous are also the categories of higher concern for humans, followed by pharmaceuticals. The pesticides and the hazardous are the categories of higher concern also on the environmental point of view. The results of our analysis could be the basis for the identification of new safety rules.

Mercury has a strong environmental impact since both its organic and inorganic forms are toxic and it represents a pollutant of global concern. Liquid Hg is highly volatile and it can be released during natural and anthropogenic processes in the hydrosphere, biosphere and atmosphere. In this study the distribution of Gaseous Elemental Mercury (GEM) and the total and leached mercury concentrations on paints, plasters, roof tiles, concretes, metals, dust and wood structures were determined in the main buildings and structures of the former Hg-mining area of Abbadia San Salvatore (Siena, Central Italy). The mining complex (divided into 7 units) covers a surface of about 65 ha and contains mining structures and managers and workers buildings. In this work, nine surveys of GEM measurements were carried out from July 2011 to August 2015 for the buildings and structures located in the units 2, 3 and 6. Moreover, detailed measurements were performed in February, April, July, September and December 2016 in the edifices and mining structures of Unit 6. GEM concentrations showed a strong variability in terms of space and time mostly depending on the distance from the building hosting driers, furnaces and condensers and ambient temperature, respectively. In the Unit 2 surveys carried out in the hotter period (from June to September) showed GEM concentrations up to 27,500 ng m⁻³, while in the Unit 6 they were on average much higher and occasionally they saturated the GEM measurement device (>50,000 ng m⁻³). Concentrations of total (in mg kg⁻¹) and leached (in μg L⁻¹) mercury measured in different building materials (up to 46,580 mg kg⁻¹ and 4,470 mg L⁻¹ for total and leached mercury, respectively) showed for the same type of material highly variable values in dependence on the edifice or mining structure from which they were collected. The results obtained in this study are of relevant interest for the operational cleanings to be carried out during the reclamation activities.

This study outlines the development of an innovative method utilizing UHPLC-PDA for the simultaneous identification of polyphenols and bitter acids (alpha-acids, beta-acids, and iso-alpha-acids) in beer samples. The resulting chemical profiles were leveraged to distinguish the characteristics of four bergamot-flavored beers, each representing distinct styles (IPA, Lager, Blanche, and ALE), produced on a pilot-scale plant. In a streamlined 29-minute analysis, twenty-nine polyphenols and fourteen bitter acids were successfully identified under optimized separation conditions. Rigorous validation, encompassing parameters such as Limit of Detection (LOD), Limit of Quantification (LOQ), R-squared (R2), repeatability, and reproducibility, was conducted for polyphenol quantification using constructed calibration curves with seven levels. Exploring polyphenolic components as potential discriminators among different beer styles, a total of thirty-two polyphenolic compounds were identified and quantified, including characteristic bergamot peel polyphenols like neoeriocitrin, naringin, and neohesperidin. The determination of bitter units and total phenols further aided in style differentiation. Multivariate analysis provided additional insights into variations among specific beer styles, revealing discrepancies in the presence or relative concentrations of specific compounds linked to brewing ingredients and processes. This research enhances to trace the fingerprinting of the chemistry governing beer quality through a straightforward and cost-effective analytical approach, readily applicable in common laboratories.

In this work, two plasmonic structures with two different periodic nanostructures (nanodisk and nanostrip arrays) separated from the gold layer by an ultrathin dielectric Al2O3 layer are proposed, and their optical properties are simulated as 3-dimensional models using COMSOL Multiphysics software tool. The optical responses, such as the amplification of the electric field and the scattering, absorption and extinction cross sections of the two structures, are investigated and compared. The results show that both structures show strong field enhancement in their gap layer, and the structure with the periodic array of metal nanodisks shows stronger field enhancement and larger absorption, extinction, and scattering cross sections in its dipole resonance wavelength, which is defined as a bright plasmonic mode. In addition, some weaker resonant modes are observed for both structures and the reason for their generation is dis-cussed. The analysis of different possible modes in such structures is crucial for their application in various fields.

Wastewater-Based Epidemiology (WBE) is currently used to monitor not only the spread of the pandemic virus SARS-CoV-2 but also for other viruses in endemic conditions, particularly in the absence of syndromic surveillance. Continuous monitoring of sewage requires high costs and significant time investment, highlighting the need for standardized methods and structured monitoring strategies. In this context, we conducted weekly wastewater monitoring in northwestern Italy, targeting Human Adenovirus (HAdV), Norovirus Genogroup II (NoVggII), Enterovirus (EV), and SARS-CoV-2. Samples collected at the entrance of treatment plants were concentrated using PEG/NaCl precipitation and viral nucleic acids were extracted and detected by real-time (RT-)qPCR. NoVggII resulted the most identified target (84.4%), followed by HAdV, SARS-CoV-2, and EV. Only HAdV and EV exhibited seasonal peaks in spring and summer. SARS-CoV-2 results compared with data previously collected in the same study area (February 2021 to September 2021) revealed a shift from an epidemic to a pandemic status, likely due to the evolution of variants. In conclusion, WBE, using standardized methods and an efficient monitoring strategy, proves valuable for virus surveillance in pandemic and epidemic scenarios, enabling the identification of temporal-local distribution patterns that are useful for making informed public health decision.

ADHD is a neurodevelopmental disorder that children and also adults can develop. A complex interplay of genetic and environmental factors may underlie interindividual variability in ADHD and potentially related aggressive behavior. Using high-resolution molecular biology techniques, we investigated the impact of some MAOA and SLC6A4 variations on ADHD and aggressive behavior in a group of 80 Italian children with ADHD and in 80 healthy controls.We found that homozygous genotypes of MAOA rs6323 and rs1137070 were associated with an increased risk of ADHD (p=0.02 and p=0.03, respectively), instead the heterozygous genotypes (GT of rs6323 and CT of rs1137030) (p=0.0002 and p=0.0006) were strongly linked to a lower risk of developing this disorder. In patients with aggressive behavior, we highligted only a weak negative association of both MAOA polymorphisms (heterozygous genotypes) with aggressiveness then, suggesting that these genotypes maybe protective towards specific changes in behavior (p=0.05). Interestingly, an increase of the GG genotype of rs6323 (p=0.01) and a decrease of GT genotype (p=0.0005) was also found in patients without aggressive behavior compared with controls. Regarding 5HTT gene genotyping, no allele and genotype differences have been detected among patients and controls. Our work shows that defining a genetic profile of ADHD may help to early detect those patients who are more vulnerable to ADHD and/or antisocial and aggressive behavior and to design precision-targeted therapies.

Introduction: Substance-induced psychotic disorder (SIPD) is a mental health condition linked to the use of a psychotropic substance whose pathogenesis has not been totally clarified. The present retrospective observational study has the objective to identify differences in clinical features and peripheral biomarkers in SIPD patients according to the main substance of abuse.Methods: A total sample of 218 patients was divided in 3 groups according to the type of consumed substance: alcohol, cannabis and psychostimulants. The 3 groups were compared for continuous variables by one-way analyses of variance (ANOVAs) and for qualitative variables by χ² tests. After removing alcohol-induced psychotic disorder group, the same analyses were repeated. Statistically significant variables from these latter analyses were included in a binary logistic regression model to confirm their reliability as predictors for cannabis- or psychostimulants-induced psychotic disorders. Results: Psychotic cannabis abusers were younger (p<0.01) and had an earlier age at onset (p<0.01). On the contrary, alcohol consumers resulted to have a longer duration of illness (p<0.01), more previous hospitalizations (p=0.04), more frequent medical comorbidity (p<0.01), higher mean Modified Sad Person Scale scores (p<0.01). Finally, psychostimulant abusers had more frequently a lifetime history of poly-substance use disorders (p<0.01). Binary logistic regression revealed that higher mean Brief Psychiatric Rating Scale scores (p<0.01) higher sodium (p=0.012) and haemoglobin(p=0.040) plasma levels were predictors of cannabis misuse in SIPD patients.Conclusions: Different clinical factors and biochemical parameters con be associated to SIPD according to the main substance of abuse, thus requiring a specific management by clinicians.

The dynamic behaviour of a machine tool (MT) directly influences the machining performances. The adoption of lightweight structures may reduce the effects of undesired vibrations and increasing the workpiece quality. This paper aims to present and compare a set of hybrid materials that may be excellent candidate to fabricate the MT moving parts. The selected materials have high dynamic characteristics and capacity to damp mechanical vibrations. In this way, starting by the kinematic model of a milling machine that highlights the main critical factors, this study paper evaluates a number of prototypes made of Al Foam sandwiches (AFS), Al Corrugated sandwiches (ACS) and materials reinforced by carbon fibres (CFRP). A set of prototypes has been fabricated, represented the Z-axis ram of a commercial milling machine. The static and dynamical properties have been evaluated by using both FE simulations and experimental tests. The obtained results show that the proposed structures may be a valid alternative to the conventional materials of MT moving parts, increasing machining performances. In particular, the AFS prototype highlighted a damping coefficient that is 20 times greater than a conventional ram (e.g. steel). The CFRP structure is able to satisfy the machining requirements with a reduced weight of 48.5%, while the ACS prototype showed a good trade-off between stiffness and damping.

This paper proposes an innovative mechatronic piezo-actuated module to control vibrations in modern machine tools. Vibrations represent one of the main issues that compromise seriously the quality of the workpiece. The active vibration control (AVC) device is composed by a host part integrated with sensors and actuators synchronized by a regulator, able to make a self-assessment and adjust to the environmental alteration. This study presents the mechatronic model based on the kinematic and dynamic analysis of the AVC device. To ensure a real time performance, a H2-LQG controller has been developed and validated by simulations involving machine tool, PZT actuator and controller models. The Hardware-in-the-loop (HIL) architecture is adopted to control and attenuate the vibrations. A set of experimental tests has been performed to validate the AVC module on a commercial machine tool. The feasibility of the real time vibration damping is demonstrated and the simulation accuracy is evaluated.

The processability of conductive polymers such as polyaniline (PANI) still poses a challenge due to their properties. The use of stabilizers, compatible and able to interact with PANI, to obtain dispersible and stable colloids is described in this work. To this aim, potato starch has been used as a steric stabilizer for the preparation of polyaniline (emeraldine salt, ES)/starch biocomposites, by exploiting oxidative polymerization of aniline in aqueous solutions containing different ratios of aniline and starch (% w/w). The polyaniline/starch biocomposites were subjected to structural and spectroscopic analyses, thermal analysis, morphological analysis and electrochemical analysis. The samples were then tested for their dispersibility/solubility in various organic solvents. The results showed the formation of PANI/starch biocomposites with an overall smaller size than starch particles, with improved aqueous dispersion and solubility in organic solvents. Although X-ray diffraction and differential scanning calorimetry analyses indicated a loss of crystallinity in the biocomposites, the cyclic voltammetry tests showed that all PANI ES/starch biocomposites display improved redox exchange properties.

Conventional monitoring relies on "in vivo" (non-destructive) measurements of aboveground organ traits (such as stems, branches, and leaves) to analyze plantation growth trends and assess the effectiveness of management practices like watering and fertilization. This study reveals the necessity of “ex vivo” (destructive) approaches, post-excavation, to ensure fully reliable monitoring of plantation performance, including belowground organ growth and development trends. We showcase the effectiveness of dendrometric analysis, which measures the annual ring width in the secondary xylem (wood) of the taproot and stem. Monitoring above- and belowground organ growth trends allow for the exploration of similarities and differences in how different tree organs respond to internal and external factors. Such monitoring is especially crucial for assessing plantation performance in challenging climates, such as those found in arid and semi-arid lands.

Background: Tibial shaft fractures are the most common of long bone fractures. The gold standard for management is locked intramedullary nailing. The freehand method under fluoroscopic monitoring is the most often utilized method for distal screw locking. Electromagnetic guidance-based distal screw locking methods have gained popularity recently. The study's objective is to evaluate the system using electromagnetic tracking data against the free-hand technique. Methods: Sixty-three patients who received intramedullary nailing for tibial shaft fractures at our institute between January 2018 and May 2022, were included in this study. Two groups of patients were distinguished: Group FH underwent freehand distal locking and intramedullary nailing, while Group SS underwent electromagnetically guided locking. Radiation exposure period, as well as dose area product, were noted and statistically compared. Results: In terms of dose area product, a mean value of 43.57±31.57 cGy/cm2 in group FH and a mean value of 27.62±11.20 cGy/cm2 in group SS (p &lt; 0.05) was assessed. Concerning the duration of surgery a mean value of 128.83±26.51 minutes was reported in group FH and a mean value of 126.42±48.31 minutes in group SS (p &gt; 0.05). Conclusions: This study confirms the use of electromagnetic-guided locking distal screws reduces the total time of exposure to ionizing radiation, with no difference in operating time.

Imperfection sensitivity of large amplitude vibration of curved single-walled carbon nanotubes (SWCNTs) is considered in this study. The SWCNT is modeled as a Timoshenko nano-beam and its curved shape is included as an initial geometric imperfection term in the displacement field. Geometric nonlinearities of von Kármán type and nonlocal elasticity theory of Eringen are employed to derive governing equations of motion of nano-beam. Spatial discretization of governing equations and associated boundary conditions is performed using differential quadrature (DQ) method and the corresponding nonlinear eigenvalue problem is iteratively solved. Effects of value and location of the geometric imperfection, and the nonlocal small-scale parameter on the nonlinear frequency ratio and imperfection sensitivity of a curved SWCNT for various boundary conditions are investigated. The results show that the geometric imperfection plays a significant role in the nonlinear vibration characteristics of curved SWCNTs.

The criteria of “Distinctness, Uniformity and Stability” as well as a high "overall quality index” are used to register the Italian modern varieties to the national register. Differently, local conservation varieties can be certified under different EU Directives having, as overall objective, the preservation of biodiversity and the containment of genetic erosion. In recent years, products derived from an-cient grains are perceived to be healthier and more sustainable by consumer, especially in Italy, with consequent higher market prices. Ancient tetraploid wheat varieties registered in the national reg-ister of conservation varieties are 28, 24 of which are Sicilian. They are supposed to have a wide genetic variability compared to modern ones, making them vulnerable of fraud because they are difficult to trace. It is therefore important to have tools able to discriminate the autochthonous Si-cilian varieties. This can be done by gluten proteins composition, which also gives information on the technological properties of derived products. Fifty-one accessions belonging to 22 ancient va-rieties of Sicilian tetraploid (mostly durum) wheat were analyzed. Although a wide intra-accession and intra-varietal variability was assessed, the gliadin pattern of bulks of seeds belonging to each variety was discriminatory. Moreover, differences in technological attitudes were found between landraces. This paves the way to use gluten protein patterns for traceability allowing local farmers and producers to valorize their products and assure consumers about the transparency of the entire supply chain.

In this study the effects of three different main preparatory tillage operations [ploughing at 0.4 m (P40) and 0.20 m (P20) depth and minimum tillage at 0.20 m depth (MT) each of them carried out at two different soil water contents (WC) [low, 58% (LH) and high, 80% (HH) of field capacity] were investigated. The results obtained in this research show high values of soil strength in term of Penetration resistance (CI) and shear strength (SS) particularly in deeper soil layers at lower water content. Fossil-fuel energy requirements both for P40 LH and P20 LH were 25 and 35% higher with respect to the HH treatments and tractor slip were very high (P40 LH = 32.4%) with respect to the P40 HH treatment (16%). Therefore soil water content had significantly influenced tractor performance during soil ploughing, particularly at 0.40 m depth while MT was not influenced at all. A significant correlation between grain yield and soil penetration resistance was found highlighting how soil strength may be good indicator of its productivity. Obtained results during these field tests allowed considering MT and P20 treatments more suitable for this type of soil in climate change scenarios.

Densely urbanized areas, with a low percentage of green vegetation, are highly exposed to Heat Waves (HW) which nowadays are increasing in terms of frequency and intensity also in the middle-latitude regions, due to ongoing Climate Change (CC). Their negative effects may combine with those of the UHI (Urban Heat Island), a local phenomenon where air temperatures in the compact built up cores of towns increase more than those in the surrounding rural areas, with significant impact on the quality of urban environment, on citizens health and energy consumption and transport, as it has occurred in the summer of 2003 on France and Italian central-northern areas. In this context this work aims at designing and developing a methodology based on aero-spatial remote sensing (EO) at medium-high resolution and most recent GIS techniques, for the extensive characterization of the urban fabric response to these climatic impacts related to the temperature within the general framework of supporting local and national strategies and policies of adaptation to CC. Due to its extension and variety of built-up typologies, the municipality of Rome was selected as test area for the methodology development and validation. First of all, we started by operating through photointerpretation of cartography at detailed scale (CTR 1: 5000) on a reference area consisting of a transect of about 5x20 km, extending from the downtown to the suburbs and including all the built-up classes of interest. The reference built-up vulnerability classes found inside the transect were then exploited as training areas to classify the entire territory of Rome municipality. To this end, the satellite EO HR (High Resolution) multispectral data, provided by the Landsat sensors were used within a on purpose developed "supervised" classification procedure, based on data mining and “object-classification” techniques. The classification results were then exploited for implementing a calibration method, based on a typical UHI temperature distribution, derived from MODIS satellite sensor LST (Land Surface Temperature) data of the summer 2003, to obtain an analytical expression of the vulnerability model, previously introduced on a semi-empirical basis.

Due to environmental concerns, natural refrigerants and their use in refrigeration and air conditioning systems are receiving more attention from manufacturers, end users and the scientific community. The study of heat transfer and pressure drop is essential for accurate design and more energy efficient cycles using natural refrigerants. The aim of this work is to provide an overview of the latest outcomes related to heat transfer and pressure drop correlations for ammonia, propane, isobutane and propylene and to investigate the current state of the art in terms of operating conditions. Available data on the existing correlations of heat transfer coefficient and pressure drop for natural refrigerants have been collected through a systematic search. Whenever possible, validity intervals are given for each correlation and the error is quantified. It is the intention of the authors that this could be a valuable support for researchers and an aid to design, with particular reference to heat pumps. A procedure based on the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) statement was adopted, and the Scopus database was used to query the relevant literature. A total of 135 publications qualified for inclusion in the survey; 34 articles report experimental investigations for not usual geometric conditions. Of the 101 selected papers related to usual geometric conditions, N = 50 deal only with HTC, N = 16 deal only with pressure drop and the remainder (N = 35) analyse both HTC and pressure drop. Among the 85 HTC papers (N = 53) deal with the evaporating condition, N = 30 with condensation and only N = 2 with the heat transfer correlations under both conditions. Most of the 101 articles concern propane and isobutane. The high temperatures are less widely investigated.

In this paper, we present an experimental procedure to enhance the dimensional accuracy of fabrication via Stereolithography (SLA) of features at the micro-scale. Using a custom benchmark part, deviations in feature dimensions (micro-pores diameters and depths) were detected and measured by confocal microscopy. Samples characterization and experimental observations allowed the identification of inaccuracy sources, mainly due to the laser beam scanning strategy and to the incomplete removal of uncured liquid resin in post-processing (i.e., IPA washing). As a technology baseline, the measured dimensional errors on pores diameters were up to -46%. A compensation method of the nominal laser spot diameter (85m) was defined and implemented resulting in relevant improvements in dimensional accuracy of 9.8% and 11.3% on full-open pores diameter and depth, respectively. Further investigation was performed on a customized test part to adjust the calibration procedure. The measurements revealed that the estimate of the laser beam spot size is 968m. Measurements on micro-pores having different sizes revealed that a constant compensation parameter (i.e., C=85, 96, 120m) is not fully effective at the micro-scale, where average errors still remain at -24%, -18.8%, and -16% for compensations equals to 85, 96 and 120m, respectively. A further experimental campaign allowed the identification of an effective nonlinear compensation law where the compensation parameter depends on the micro-feature size C= f (D). Results show a sharp improvement in dimensional accuracy on micro-pore fabrication, with errors consistently below +8.2%. The proposed compensation method can be extended for the fabrication of any micro-features without restrictions on the specific technology implementation. Concerning the inaccuracy introduced by the laser path, experimentation with a customized part allowed the optimization of the part orientation to reduce the errors and their differences along the X and Y machine axes.

In the conservation of monumental heritage, the collection and utilization of information are of primary importance. The Heritage Building Information Modeling (HBIM) procedure harnesses the potential of three-dimensional models, offering significant advantages in accessing documentation, interoperability, multidimensionality of intervention design, cost evaluation and maintenance management. Attention here is focused on the Certosa di Pisa, a large historical complex built in the 14th century as a monastery of the Carthusian order, currently in a state of deterioration and in need of restoration and re-functionalization. The multifaceted nature of this monumental complex, with its intricate interplay of architectural elements spanning different historical periods and featuring diverse techniques, poses a significant challenge for structural safety assessment. This case study presents an opportunity to explore an HBIM approach to streamline the diagnostic process and facilitate the intervention design phase. The goal is achieved by utilizing an accurate 3D model enriched with data from multiple sources and automating certain operations for structural assessment. The usefulness of the HBIM methodology is highlighted as a valuable tool in the realm of Cultural Heritage structures for both technicians and scholars alike.

The use of privileged scaffolds as starting point for the construction of libraries of bioactive compounds is a widely used strategy in drug discovery and development. Scaffold decoration, morphing and hopping are additional techniques that allow to modify the privileged framework chosen and better explore the chemical space around it. In this study, two series of highly functionalized pyrimidine and pyridine derivatives were synthesized by scaffold morphing approach of triazine compounds obtained previously as antiviral agents. Newly synthesized azines were evaluated against lymphoma, hepatocarcinoma, and colon epithelial carcinoma cells showing in five cases acceptable to good anticancer activity associated to low cytotoxicity on healthy fibroblasts. Finally, ADME in vitro studies were conducted on the best derivatives of the two series showing good passive permeability and resistance to metabolic degradation.

An 8-months old male American Staffordshire terrier was referred for a no weightbearing lameness of the right pelvic limb, hyperthermia, lethargy and inappetence caused by hematogenous osteomyelitis. Orthopedic, radiographic and tomographic examinations revealed a bone sequestrum of 4 x 1.4 cm and active periosteal reaction of the caudo-lateral cortical in the metaphysis and the distal third of the right femoral diaphysis, medullary osteolysis and interruption of the cranio-medial cortical profile, with involvement of the femoral trochlea leading to a secondary medial patella luxation. Once skeletally mature, after 4 months from surgical debridement and aggressive antibiotic therapy against Klebsiella oxytoca revealed by bacteriological exam, the patient underwent prosthetic surgery for the application of a custom-made patellar groove replacement (PGR) to fill the bone defect and restore the femoral trochlea surface. Despite the serious injury that afflicted the right pelvic limb, the surgery had satisfactory outcomes until the last 18-months postoperative follow up.

ABSTRACT Background: To date, the COVID-19 pandemic has been the foremost health concern for humankind in the new millennia. This paper aims to describe the related hospitalizations in Italy during the first two years of the health emergency. Design and methods: This is a retrospective, population-based study of Italian hospitalizations for patients diagnosed with COVID-19 during the 2020-2021 period, extracted from the National Hospital Discharge Registry. The outcome variables considered include hospital admissions, costs, and length of stay, among other hospitalization-level variables. Costs were estimated through the charges associated with the Diagnosis-Related Group and Major Diagnostic Categories coding system, plus an additional cost attributed to COVID-19 admissions. To these charges was added an extra cost defined by the ministry of health. Results: In Italy, there were 357,354 hospitalizations for COVID-19 attributed to 298,856 patients in 2020 and 399,043 hospitalizations for COVID-19 attributed to 333,447 patients in 2021. COVID-19 patients faced a transfer rate thrice that of other patients. Hospitalizations were concentrated predominantly in the northern regions, particularly in the first year. Hospitalization rates varied by age in a sine wave pattern, peaking in the youngest and oldest age groups, with mortality rates escalating with age— tending to remain below 3% for those under 44 but surging to 40% in individuals over 75. The financial impact of COVID-19 hospitalizations was substantial, with total costs reaching €3.97 billion in 2020 and €4.99 billion in 2021. Costs per admission and per day also rose, from €11,112 and €807 in 2020 to €12,503 and €844 in 2021, respectively. Excluding the added financial burden of COVID-19, costs would have been notably lower. Hospitalizations involving continuous invasive mechanical ventilation were particularly costly (about 24.000 euros x admission), reflecting the significant resources required for these treatments. Conclusion: Implementing a protective pad around the entire health system that leverages networks of family doctors and nurses, connected in real time to the entire health system, can be crucial. Such a network, tasked with monitoring the local epidemiological situation, protecting vulnerable individuals also through telehealth visits, and establishing a triage system for infections in the initial phase, may effectively help in managing virus spread and protecting hospitals from unpredictable waves of admission demand. Strengthening primary health care could be a decisive factor for the future and enhance the system's resilience in facing new challenges.

“Pecorino” is a typical semi-hard cheese obtained with raw or heat-treated sheep milk using procedures to valorize the raw material's chemical and microbiological properties. In the present study, using a high throughput method of 16S rRNA gene sequencing, we assessed the evolution of the microbiome composition from milk to Pecorino cheese in artisanal processes using milk from Comisana and Lacaune sheep breeds. The comparative analysis of the bacterial com-munity composition revealed significant differences in the presence and abundance of specific taxa in the milk microbiome of the Comisana and Lacaune breeds. NGS analysis also revealed differences in the curd microbiome related to dairy farming practices, which have a relevant effect on the final structure of the Pecorino-cheese microbiome.

Several pathotypes of enteric E. coli have been identified. The group represented by Shiga toxin-producing E. coli (STEC) is of particular interest. Raw milk and raw milk products are significant sources of STEC infection in humans; therefore, identifying pathogens at the herd level is crucial for public health. Most national surveillance programs focus solely on raw milk and raw milk cheeses that are ready for retail sale, neglecting the possibility of evaluating the source of contamination directly at the beginning of the dairy chain. In order to assess the viability of new molecular methodologies applied to raw milk filters enabling the identification of the presence of STEC serotypes in milk production and apply the same methods to identify the presence of these pathogens in calf feces we analyzed, through a commercial real-time PCR assay, a total of 290 samples coming from 18 different dairy herds; 88 bulk tank milk (BTM), 104 raw milk filters (RMF) and 98 calves’ feces samples. In total 3.4% of BTM, 41.4% of RMF and 73.4% of calves’ feces tested positive for stx presence, supporting our hypothesis that BTM is not a suitable matrix to assess the STEC presence at herd level, underestimating it. Our conclusion is that the surveillance program needs critical and extensive improvements such as RMF and calves’ feces analysis implementation in order to be more efficient in detecting and preventing STEC infections. The epidemiology of these infections and the characteristics of the pathogen clearly show how a One Health approach will be pivotal to improve our capabilities to control the spread of these infections.

Background: clubfoot is a common congenital deformity. The Ponseti technique, involving early corrective manipulations followed by the application of long leg casts and Achilles tenotomy, is widely accepted as the preferred treatment. Rapid healing of the tendon after surgery has been documented, but the aspect regarding tendon structure and properties is not known. Three cases of Achilles tendon rupture in adolescent previously treated for clubfoot have been described in the literature. Since rupture is a rare event in this age group a possible correlation with previous surgery has been hypothesized. The primary aim of the study was to compare the ultrasound findings of the Achilles tendon, in patients treated for clubfoot, between patients treated with casting alone and the ones who underwent surgery (percutaneous tenotomy or Z-plasty lengthening). Methods: 22 asymptomatic patients, (34 feet) median age 12 years, previously treated for clubfoot, were recruited for this study; the patients underwent an Achilles tendon ultrasound examination during a follow-up outpatient visit. Results: a greater thickness and structural alterations with presence of hypoechoic areas of the operated tendons compared to those treated with plaster alone were observed (p value: 0.0498 and

The paper presents the design and the implementation of different advanced control strategies that are applied to a nonlinear model of a thermal unit. A data–driven grey–box identification approach provided the physically meaningful nonlinear continuous–time model, which represents the benchmark exploited in this work. The control problem of this thermal unit is important since it constitutes the key element of passive air conditioning systems. The advanced control schemes analysed in this paper are used to regulate the outflow air temperature of the thermal unit by exploiting the inflow air speed, whilst the inflow air temperature is considered as an external disturbance. The reliability and robustness issues of the suggested control methodologies are verified with a Monte–Carlo analysis for simulating modelling uncertainty, disturbance and measurement errors. The achieved results serve to demonstrate the effectiveness and the viable application the suggested control solutions to air conditioning systems. The benchmark model represents one of the key issues of this study, which is exploited for benchmarking different model–based and data–driven advanced control methodologies through extensive simulations. Moreover, this work highlights the main features of the proposed control schemes, while providing practitioners and heating, ventilating and air conditioning engineers with tools to design robust control strategies for air conditioning systems.

Toxoplasmosis is a zoonosis of warm-blooded animals, affecting also humans, caused by Toxo-plasma gondii, an obligate intracellular parasite with a complex biological cycle. Toxoplasmosis is considered a re-emerging zoonosis and an important public health threat, also for the absence, up to now, of efficient vaccines and preventive measures. Sources of transmission to humans are environmental or food-borne, mainly through the consumption of raw and undercooked meat, predominantly of Sus scrofa, considered highly susceptible to T. gondii. Mainly in the last dec-ades, an effective strategy to counter animal infectious diseases was based on the discovery of resistance immuno-genetic markers, possibly to be used for association studies between geno-typic and phenotypic traits and consequently in Marker Assisted Selection. Until now, this gen-otyping approach has never been adopted for T. gondii infection, so this study aimed, for the first time, to fill this gap. In particular, pigs, reared in different farms of Central Italy, were serologically characterized by an ELISA assay performed on diaphragm meat juice. Out of 179 tested animals, 98 resulted seropositive (54.74%), 57 seronegative (31.84%) and 24 doubtful (10.6%), underlining a possible re-emerging diffusion of this protozoan in the investigated areas. Atten-tion was firstly focused on IL-18 gene, encoding for a pro-inflammatory cytokine that plays a key role starting from the upstream steps of the immunity pathway towards T. gondii. A RT-PCR assay followed by Sanger sequencing of IL-18 cDNA was de novo developed. For this interleukin, at this stage, genetic analysis has not highlighted significant polymorphic variations compared to the reference sequence, except for a seropositive animal. However, the outcomes of this pre-liminary innovative study will be investigated in depth analyzing other relevant genetic re-gions and other target genes.

Background: Open AI developed ChatGPT, a language model based on the GPT architecture, designed for text-based communication. Trained on diverse internet texts, ChatGPT generates contextually appropriate responses using machine learning. It understands input through analysis and context interpretation, generating coherent and contextually relevant responses. Interaction is possible through messaging platforms. Materials and Methods: In November 2023, we utilized ChatGPT 3.5, the default version at that time, to answer questions from the Italian National Residency Program Admission Tests (SSMs) of 2021, 2022, and 2023. The questions cover clinical, diagnostic, analytical, therapeutic, and epidemiological scenarios, sometimes accompanied by images. The study compared ChatGPT's answers to the official corrections on the Italian Ministry of University and Research (MUR) website. The scoring method used for evaluation was 1 point for correct answers, 0 points for unanswered questions, and -0.25 points for incorrect answers, reflecting the SSM test scoring system. Results: In summary, ChatGPT was tested with a total of 420 questions, 140 for each test. It achieved an overall accuracy of 80.48%, providing correct answers for 338 questions and incorrect answers for 82 questions. When faced with questions containing both text and images, it answered 55% correctly and 45% incorrectly. The model's performance varied over time, with an 82.14% accuracy rate in 2021 and 2022 (115 correct out of 140) and a 77.14% accuracy rate in 2023 (108 correct out of 140). Applying thisscoring method to the SSM test, ChatGPT would have scored 105 points in 2021 and 2022, and 100 points in 2023. Conclusions: ChatGPT has exhibited above-average performance in the last three SSM tests, highlighting its robust capability to interpret clinical scenarios and offer precise diagnostic and therapeutic guidance. Despite this, some limitations persist, notably the software's inability to interpret non-textual information.

The theory of heavy ion double charge exchange (DCE) reactions proceeding by effective rank–2 isotensor interactions is presented. Virtual pion–nucleon charge exchange interactions are investigated as the source for induced isotensor interactions, giving rise to the Majorana DCE (MDCE) reaction mechanism. MDCE is of a generic character, proceeding through pairs of complementary (π±,π∓) reactions in the projectile and target nucleus. The dynamics of the elementary processes is discussed where the excitation of pion–nucleon resonances are of central importance. Investigations of initial and final state ion–ion interactions show that these effects are acting as vertex renormalizations. In closure approximation, well justified by the finite pion mass, the second order transition matrix elements reduce to pion potentials and effective two–body isotensor DCE interactions, giving rise also to two–body correlations in either of the participating nuclei. Connections to neutrinoless Majorana double beta decay (MDBD) are elucidated at various levels of dynamics, from the underlying fundamental electro–weak and QCD scales to the physical scales of nuclear MDBD and MDCE physics. It is pointed out that heavy ion MDCE reactions may also proceed by competing electro–weak charge exchange processes, leading to lepton MDCE by electrons, positrons, and neutrinos.

Azobenzene photoswitches are fundamental components in contemporary approaches aimed at light-driven control of intelligent materials. Significant endeavors are directed towards enhancing the light-triggered reactivity of azobenzenes for such applications and obtaining water-soluble molecules able to act as crosslinkers in a hydrogel. Here, we report the rational design and the synthesis of azobenzene/alginate photoresponsive hydrogels endowed with fast reversible sol-gel transition. We started with the synthesis of three cationic azobenzenes (AZO A, B, and C) and then incorporated them in sodium alginate (SA) to obtain photoresponsive supramolecular hydrogels (SMHGs). The photoresponsive properties of the azobenzenes were investigated by UV-Vis and ¹H NMR spectroscopy. Upon irradiation with 365 nm UV light, the azobenzenes demonstrated efficient trans-to-cis isomerization, with complete isomerization occurring within seconds. The return to the trans form took several hours, with AZO C exhibiting the fastest return, possibly due to higher trans isomer stability. In the photoresponsive SMHGs, the minimum gelation concentration (MGC) of azobenzenes was determined for different compositions, indicating that small amounts of azobenzenes could induce gel formation, particularly in 5 wt% SA. Upon exposure to 365 nm UV light, the SMHGs exhibited reversible gel-sol transitions, underscoring their photoresponsive nature. This research offers valuable insights into the synthesis and photoresponsive properties of cationic, water-soluble azobenzenes, as well as their potential application in the development of photoresponsive hydrogels.

Negative temperature coefficient (NTC) materials are usually based on ceramic semiconductors and electrons are involved in their transport mechanism. A new type of NTC material, adequate for alternating current (AC) applications, is represented by zeolites. Indeed, zeolites are single-charge carrier ionic conductors with a temperature-dependent electrical conductivity. In particular, electrical transport in zeolites is due to the monovalent charge-balancing cations, like K⁺, capable of hopping between negatively charged sites in the aluminosilicate framework. Owing to the highly non-linear electrical behavior of the traditional electronic NTC materials, the possibility to have alternative types of materials, showing linearity in the electrical behavior, is very desirable. Among different zeolites, the natural clinoptilolite has been selected for investigating the NTC behavior since it is characterized by high zeolite content, convenient Si/Al atomic ratio, good mechanical strength, due to its compact microstructure, and low toxicity. Clinoptilolite has shown a rapid and quite reversible impedance change under heating, characterized by a linear dependence on temperature. X-ray diffraction (XRD) has been used to identify the natural zeolite, to establish all types of crystalline phases present in the mineral, and to investigate the thermal stability of these phases up to 150°C. X-ray photoelectron spectroscopy (XPS) analysis has been used for the chemical characterization of the natural clinoptilolite sample, providing important information on the cationic content and framework composition. In addition, since electrical transport takes place in the zeolite free-volume, a Brunauer–Emmett–Teller (BET) analysis of the mineral has been also performed.

This paper describes the first results of an Image Recognition Based Location (IRBL) for mobile application focusing on the procedure to generate a Database of range images (RGB-D). In an indoor environment, to estimate the camera position and orientation, a prior spatial knowledge of the surrounding is needed. In order to achieve this objective a complete 3D survey of two different environment (Bangbae metro station of Seoul and E.T.R.I. building in Daejeon – Republic of Korea) was performed using LiDAR (Light Detection And Ranging) instrument and the obtained scans were processed in order to obtain a spatial model of the environments. From this, two databases of reference images were generated using a specific software realized by the Geomatics group of Politecnico di Torino (ScanToRGBDImage). This tool allow to generate synthetically different RGB-D images) centered in the each scan position in the environment. Later, the external parameters (X, Y, Z, ω, φ, κ) and the range information extracted from the DB images retrieved, are used as reference information for pose estimation of a set of acquired mobile pictures in the IRBL procedure. In this paper the survey operations, the approach for generating the RGB-D images and the IRB strategy are reported. Finally the analysis of the results and the validation test are described.

Machine Learning deals with creating algorithms capable of learning from the provided data. These systems have a wide range of applications and can also be a valuable tool for scientific research which in recent years has been focused on finding new diagnostic techniques for particle accelerator beams. In this context SPARC_LAB is positioned, a facility located at the Frascati National Laboratories of INFN, where the progress of beam diagnostics is one of the main developments of the entire project. With this in mind, you aim to present the design of two neural networks aimed at predicting the spot size of the electron beam of the plasma-based accelerator at SPARC_LAB, which powers an undulator for the generation of x-ray Free Electron Laser (XFEL). Data-driven algorithms use two different data preprocessing techniques, namely autoencoder neural network and PCA. With both approaches, the predicted measurements can be obtained with an acceptable margin of error and most importantly without activating the accelerator, thus saving time, even compared to a simulator that can produce the same result but much more slowly. The goal is to lay the groundwork for creating a digital twin of linac and conducting virtualized diagnostics using an innovative approach.

Polar stratospheric clouds (PSCs) form in polar regions typically between 15 and 25 km, when the local temperature is sufficiently low. PSCs play an important role in the ozone chemistry and the dehydration and denitrification of the stratosphere. Lidars with a depolarization channel may be used to detect and classify different classes of PSCs. The main PSC classes are water ice, nitric acid trihydrate (NAT) and supercooled ternary solutions (STS), the latter being liquid droplets consisting of water, nitric acid and sulphuric acid. PSCs have been observed at the lidar observatory at Concordia Station from 2014 on. The harsh environmental conditions at Concordia during winter render successful lidar operation difficult. In order to facilitate the operation of the observatory several measures have been put in place to achieve an almost complete remote control of the system. PSC occurrence is strongly correlated with local temperatures and is affected by dynamics, as the PSC coverage during the observation season shows.

In this paper we derive a unified perspective for Optimal Transport (OT) theory and Mean Field Control (MFC) theory to analyse the learning process for Neural Networks algorithms in a high-dimensional framework. We consider Mean Field Neural Networks in the context of MFC theory, specifically the mean field formulation of OT theory that allows the development of highly efficient algorithms while providing a powerful tool in the context of explainable Artificial Intelligence.

The extensive collection of paper documents and books stored in the archives of universities worldwide is a hidden cultural heritage that is frequently inaccessible. To overcome this problem, the University of Genoa, Italy, seeks to collect, store, and digitize a wide variety of items, encompassing books, manuscripts, archival materials, and documents related to museum artifacts, which together form a cultural heritage of great importance and historical significance. To make such a cultural heritage accessible to both humans and machines, images and videos must be provided with alternate descriptions, metadata, and speech-to-text transcriptions while ancient texts, for which OCR techniques are often not effective, must be accompanied by word-for-word transcripts. This work presents the design of a transcription system for the “University Museum System” at the University of Genoa, Italy (SMA-UniGe), including user interface elements and users’ engagement techniques. The goal is to create an accessible digital heritage that can be enjoyed by all, facilitated by a community of digital volunteers who are eager to dedicate their time, have a great experience, socialize, and interact on the proposed transcription system. The system exploits gamification theory to transform the typically monotonous task of transcription into a captivating experience. This activity is in line with the so-called University third mission, i.e., the activity of public engagement that aims at generating knowledge outside the academic environment to the benefit of the social, cultural, and economic development.

In this work, we explore new constraints on phantom scalar field cosmologies with a scalar field employing early times catalogues related to CMB measurements, along with the local standard observables, like Supernovae Type Ia (SNIa), H(z) measurements (Cosmic Clocks), and Baryon Acoustic Oscillations (BAO) baselines. In particular, we studied a tracker phantom field with hyperbolic polar coordinates that have been proposed in the literature. The main goal is to obtain precise cosmological constraints for H0 and σ8, in comparison to other constructions that present tension in early cosmological parameters. Our results show that phantom scalar field cosmologies have a reduced statistical tension on H0 that it is less than 3σ using model-independent CMB catalogues as SPT-3G+WMAP9 and ACTPol DR-4+WMAP9 baselines. This suggests these models using a different phantom potential might address the Hubble constant problem and reduce the systematics involved.

Peritoneal dialysis (PD) is a home-based efficacious modality for replacement of renal function in end-stage kidney failure patients but is still under-prescribed. A major limitation is the durability of the dialytic technique. Continuous exposure of the peritoneum to bioincompatible conventional glucose-based solutions is thought to be the main cause of long-term morpho-functional peritoneal changes eventually resulting in ultrafiltration failure. Poor PD solution biocompatibility is primarily related to the high glucose content, which is not only detrimental to the peritoneal membrane but has many potential metabolic side effects. To improve the clinical outcome and prolong the survival of the treatment, PD-related bioincompatibility urgently needs to be overcome. However, combining dialytic and osmotic efficacy with a satisfactory biocompatible profile proves quite difficult. New approaches targeting the composition of the PD solution include replacement of glucose with other osmotic agents and the addition of cytoprotective or osmo-metabolic compounds. Other strategies include infusion of mesenchymal cells or the administration of orally active agents. In the present article we review the current evidence on efforts to improve the biocompatible and functional performance of PD, focusing on studies performed in vivo (animal models of PD, human subjects on PD).

The aim of the present study was to investigate the incidence of breast (females), prostate, testicular and thyroid cancer in the Italian National Priority Contaminated Sites (NPCSs), served by cancer registries, where the presence of endocrine disruptors (EDs), reported to be linked to these tumors, was documented. Evidence of carcinogenicity of EDs present in NPCs was assessed based on evaluation by international scientific institutions/committees. Standardized Incidence Ratios (SIRs) were computed for each NPCS and cancer site with reference to the time window 1996-2005. Excess incidence of one or more cancer site at study was found in twelve out of fourteen NPCSs. Significantly increased SIRs were found for breast cancer in eight NPCSs, for prostate cancer in six, for thyroid cancer (both gender) in four and for testicular cancer in two. Non significantly increased SIRs were found in five NPCSs for testicular cancer and in two for thyroid cancer (males). Even if increased incidence of one or more cancer sites at study were found in several NPCSs, the ecological study design and the multifactorial etiology of the considered tumors do not allow reaching conclusions in terms of causal links with environmental contamination. In light of the observation of some excesses in SIRs, continuing epidemiological surveillance is warranted.

Background: Early postoperative airway management after laryngo-tracheal surgery is crucial. Acute respiratory failure due to glottis’ oedema may occur, requiring reintubation. This can prolong ventilatory assistance, jeopardizing the anastomosis. To date, only judicious steroid administration and fluid management are available to avoid more invasive procedures. High-Flow-Oxygen-Therapy(HFOT) is a noninvasive O2 support method providing humidification, warmed air, Positive-End-Expiratory-Pressure(AIRVO2). No data exist about HFOT use to prevent early complications after laryngo-tracheal surgery. Methods: Between Sept.2020-Sept.2022, 107 consecutive patients underwent laryngo-tracheal surgery received HFOT(Group A). Data and long-term results were compared with those of 80 patients operated between Sept.2018-Aug.2020(Group B), when HFOT was not available. All patients were operated in a single center. No pre- or post-operative settings changed, except for HFOT introduction. We analyzed and compared the risk for “delayed” reintubation (unexpected reintubation within the first 24-48 hours after extubating/laryngeal mask removal) in the two groups. Results: No patients reported HFOT-related adverse events. Control group(B) presented “delayed” reintubation in 37% (p= 0.027), Intensive Care Unit admission in 67%(p=0.005) and longer hospital stay(p=0.001) compared to HFOT group(A). Minor complications rate was 3% in both group and overall mortality was 0%. Re-stenosis was described in 4.6% of HFOT group, without a statistically significant difference (p=0.7006). Conclusions: Our study is the first to investigate HFOT use in patients undergoing laryngo-tracheal surgery, potentially representing a consistent innovation in the peri-operative management of these patients. With the limit of a retrospective series, we would suggest HFOT use for preventing post-operative reintubation rate, possibly reducing ICU admission and hospital stay.

Factors responsible of species distribution were intensively investigated in the past, including response at different spatial scales. The aim of the present research is to review the most relevant factors explaining chironomid species distribution focusing to factors operating at different spatial scales, such as latitude, longitude, altitude, water temperature, dissolved oxygen, nutrients acting at regional, country, water basin extension. Data including chironomid species abundances from different lentic and lotic waters from Italy and other surrounding countries were analyzed with different multivariate methods: partial canonical correspondence analysis and multiple discriminant analysis. Spatial analysis included univariate Moran’I correlograms, multivariate Mantel correlograms and Moran’s Eigenvectors Maps (MEM) calculation. The results confirmed previous conclusions, that is habitat type including different running waters reaches (kryal, krenal, rhthral, potamal) and different lake types is the most significant factor in separating chironomid assemblages and spatial factors act only as indirect influencers..

The “tubulin code” combines different α/β-tubulin isotypes with several post-translational modifications (PTMs) to generate microtubule diversity in cells. During cell division, specific microtubule populations in the mitotic spindle are differentially modified, but only recently has the functional significance of these modifications started to be elucidated. In particular, α-tubulin detyrosination of stable microtubules in the spindle was shown to guide chromosomes during congression to the metaphase plate and allow the discrimination of mitotic errors, whose correction is required to prevent chromosomal instability (CIN), a hallmark of human cancers. Although alterations in certain tubulin PTMs have been reported in human cancers, it remains unclear whether and how tubulin PTMs have any functional implications for cancer cell properties. Here we review the role of the tubulin code in chromosome segregation during mitosis, together with the emerging cancer tubulin code and discuss possible links, as well as the respective diagnostic, prognostic and therapeutic implications for human cancers.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

Shared public buildings have become centers of innovation, integrating advanced technologies to meet evolving societal needs. With a heightened emphasis on occupants’ health and well-being, these buildings serve as hubs for technological convergence, facilitating seamless connectivity and intelligent data analysis and management. Within this context, environmental monitoring emerges as a foundational element, pivotal to all aspects of building management. This article provides findings from the nationally funded RE-START project, which focuses on shared public buildings, with special regard to educational and medical facilities. The project explores enhanced indoor air quality monitoring, focusing in particular on CO2 concentration that is directly correlated with occupancy, as a fundamental element for developing health and safety protocols, energy efficiency strategies, integration of smart building technologies, and data-driven energy management. The intersection of environmental monitoring, energy efficiency, security, and IoT technologies in in indoor spaces are relevant. The outcomes of the study reveal the delicate nature of all the involved components, that need to be carefully developed in an integrated manner.

Polyhydroxyalcanoates (PHAs) are biodegradable polymers synthesized in cytoplasmic granules in bacteria, such as Cupriavidus necator (Ralstonia eutropha), Alcaligenes latus, Pseudomonas spp., Comamonas spp. and other species. PHAs accumulation occurs in response to stress conditions, i.e. under high carbon and low nitrogen (24:1 ratio). PHA can be synthesized using recombinant microorganisms (provided with the operon phbA/phbB/phbC), escaping the constrains of nutrient request, except addition of high amount of sugar (glucose, lactose, fructose). In this study; E. coli was genetically modified for PHB production in biofermentors. The production of PHA at industrial scale requires a continuous supplementation of fermentable sugars to support the availability of nutrients and to assess the level of the exponential growth phase; since sugars are required either for bacterial growth either for PHA synthesis and energy storage. The biofermentors need to be run in automated system. Sensors are used at many points in fermentators; in the evaluation of parameters: consumption of sugars; cell density; quantification of PHB synthesis. The need of operational control during the fermentation has prompted us to application of three measurements; one unit linked to a Nanodrop to evaluate OD; one linked to a reaction chamber to measure sugars consumed by enzyme based fluorescence detection; and one for bacteria Nile Blue staining and fluorescence intensity reads. The growth of bacteria on three different plant by-products was monitored and PHB production in four days using a banana by-product feed was optimised. These detectors will make possible to exploit the full potential of bioreactors optimizing the time of use and maximizing the number of bacteria synthesizing PHA.

The main aim of this work is to present a step-by-step procedure to model and analyze the power loss distribution of three-level Gallium Nitride (GaN) inverters. It has been applied to three distinct three-phase three-levels voltage source inverters utilized in electric traction drives: Active Neutral Point Clamped, Neutral Point Clamped and T-Type Neutral Point Clamped. The proposed analytical power loss modelling, combined to an equivalent representation of the electrical machine demonstrated to be a viable solution to achieve a time-saving and low computational burden simulation platform, leading to satisfying accuracy results. This has been confirmed by comparing the results carried out from the simulations of a 110kW permanent magnet synchronous motor drive and those determined by considering a simplified circuital representation based on the proposed analytical power loss modelling.

By using the particle swarm optimization algorithm for crystal structure prediction, we reveal a newly orthorhombic Cmcm structure of HfB4, which is more energetically superior to the previously proposed YB4-, ReP4-, FeB4-, CrB4-, and MnB4-type structures in the considered pressure range. The phonon dispersion and elastic constants calculations confirm that the new phase is dynamically and mechanically stable. The calculated large shear modulus (240 GPa) and high hardness (45.7 GPa) imply that the predicted Cmcm-HfB4 is a potential superhard material. Meanwhile, the directional dependences of the Young's modulus, bulk modulus, and shear modulus for HfB4 are systematically investigated. Further analyses of the density of states and electronic localization function indicate that the strong B-B and B-Hf covalent bonds greatly contribute to its high hardness and stability.

In recent years, there has been an increasing interest in adopting novel sensing technologies for the continuous monitoring of structural systems. In this respect, Micro-Electro-Mechanical System (MEMS) sensors are widely used in several applications, including Structural Health Monitoring (SHM). Thanks to their significantly lower cost, ease of installation on the structure, and lower power consumption, they enable extensive, pervasive, and battery-less monitoring systems. This paper presents an innovative high-performance device for SHM applications, based on a low-noise triaxial MEMS accelerometer, providing a guideline and insightful results about the opportunities and capabilities of these devices. Sensor nodes have been designed, developed, and calibrated to meet structural vibration monitoring and modal identification requirements. These components include a protocol for reliable command dissemination through the network and data collection, and improvements to software components for data pipelining, jitter control, and high-frequency sampling. Devices were tested in the lab using shaker excitation. Results demonstrate that MEMS-based accelerometers are a feasible solution to replace expensive piezo-based accelerometers. Deploying MEMS is promising to minimize sensor node energy consumption. Time and frequency domain analysis show that MEMS can correctly detect modal frequencies, useful parameters for damage detection. The acquired data from the test bed were used to examine the functioning of the network, data transmission, and data quality. The proposed architecture has been successfully deployed in a real case study to monitor the structural health of the Marcus Aurelius Exedra Hall within the Capitoline Museum of Rome. The performance robustness was demonstrated and the results showed that the wired sensor network provides dense and accurate vibration data for structural continuous monitoring.

The study of precipitation amount at different time scales constitutes an important issue in climate research and risk assessment. When dealing with daily totals, a frequent but sometimes underestimated problem is at what time the observation day begins. The choice of different starting times may lead to incompatibility between stations and incorrect identification of extreme events. In this work, the problem of temporal misalignment between precipitation datasets characterized by different starting time of the observation day is analyzed. The most widely used adjustment methods (1day and uniform shift) and two methods based on reanalysis (NOAA and ERA5) are evaluated in terms of temporal alignment, precipitation statistics and percentile distributions. As test series, the precipitation amount collected from 9 a.m. local time (09 LT) on the previous day to 09 LT on the target day (9-9 datasets) of the Padua and nearby stations in the period 1993-2022 have been selected. Results show that the reanalysis-based methods, in particular ERA5, outperform the others in temporal alignment, regardless the station. But, for the periods in which reanalysis data are not available, “1day” method, which shifts the daily amount back one calendar day, and “unif” method, which distributes uniformly the daily total from a 2-day moving window surrounding the target date, can be considered valid alternatives. On the other side, concerning the precipitation statistics, the reanalysis-based methods are not the best option, as they increase the precipitation frequency and reduce the mean value over wet days, NOAA much more than ERA5. Nevertheless, the uniform method provides a larger deviation from the original daily series. The use of the series of a station nearby the target one, which is mandatory in case of missing data, gives similar or better results than applying any adjustment method to the 9-9 series. General conclusions can hardly be drawn as they depend on the method and station. For the Padua dataset, the analysis was repeated at monthly and seasonal resolution. In general, the adjustment series show the most relevant changes in the precipitation statistics in summer and less temporal alignment with the original series in summer and autumn, the two seasons mainly affected by heavy rains in Padua. Finally, the percentiles distribution, analyzed for all the methods and stations, indicates that any adjustment method underestimates the percentile values, except ERA5. Only Legnaro, the station most correlated with Padua, gives results like ERA5.

Hazelnut is a widespread nut species, especially in Europe, that can be consumed raw or roasted, due to its pleasant taste and nutritional properties. Despite the renowned beneficial properties, hazelnuts contain several proteins capable of inducing food allergy in sensitized individuals such as Cor a 2 (profilin), Cor a 8 (lipid transfer protein), Cor a 9 (11S seed storage globulin, legumin-like) and Cor a 11 (7S seed storage globulin, vicilin-like). In the present paper we investigated the effectiveness of autoclave based treatments in decreasing the allergic potential of hazelnut as also assessed by submitting the treated material to in vivo skin prick test and to in vitro immunoblot analysis with sera of allergic individuals exposed to the treated food material. This preliminary analysis shows that autoclave treatment, preceded by hydration and/or followed by drying, seems to be a promising approach and appears to be effective in reducing the allergenicity of hazelnut in most patients, probably due to the denaturation of most major and minor allergenic proteins. This work will open to the opportunity to produce, in perspective, hypoallergenic hazelnut derivatives tolerated by the allergic subjects.

Magnesium is one of the lightest structural metal used in different industrial sector and many works are present in literature about the study of its reinforcement by fillers addition. Basalt fibres are natural fillers with good mechanical properties, excellent resistance to high temperature and lower cost than carbon fibres. For these aspects, in the last years they are increasingly used in the production of composite materials with polymeric matrices. However, very few information are presents in literature about the use of basalt fibres as reinforcement in metal matrix composite materials. It is well known that the impregnation of fibres reinforcement affects the mechanical behavior of composites materials. The aim of this study is to investigate the impregnation and the behavior of basalt fibres in a magnesium alloy composite material manufactured by a centrifugal casting technique.

Woodland strawberry (Fragaria vesca L.) is an underutilized plant species, appreciated by consumers for its qualitative features. Utilizing technical means of production, such as plant biostimulants, that can increase crop productivity and quality could be highly important in woodland strawberry cultivation. The scope of the present study was to appraise the influence of two biostimulants (Trichoderma atroviride and plant protein hydrolysate) - used either alone or combined - on plant performance and economic profitability of two woodland strawberry genotypes (‘Alpine’ and ‘Regina delle Valli’). Overall, data showed that ‘Alpine’ had the highest productive performances, whereas ‘Regina delle Valli’ revealed the highest fruit qualitative traits. T. atroviride inoculation and V-PH application significantly boosted plant marketable yield (+20.5% for T. atroviride and +12.9% for V-PH), total sugars (+1.9% for Trichoderma and +1.4% for V-PH) and anthocyanins (+14.1% for T. atroviride and +9.8% for V-PH) compared to non-treated plants. Plants supplied with both biostimulants had higher marketable yield (+34.8%), mean fruit weight (+6.0%), fruit dry matter (+13.8%), total sugars (+3.5%), ascorbic acid (+12.7%), flavonoid (+26.3%) and anthocyanins (+29.9%) compared to non-treated plants. Furthermore, our study revealed that the highest fruit polyphenols concentration was recorded in both genotypes treated with the combination of biostimulants and in ‘Regina delle Valli’ sprayed with V-PH, whereas the highest antioxidant activity was found in ‘Regina delle Valli’ fruit when plants were supplied with both biostimulants. Our study pointed out that the application of microbial and non-microbial biostimulants, especially in combination, might be an useful strategy for improving performances of underutilized species and, therefore, encourage its cultivation, valorisation and economic profitability (+10195.3 €/ha when plants were exposed to both biostimulants).

Modern organic synthesis is majorly focused on developing environmentally benign synthetic protocols by employing green chemistry principles. Accordingly, in our recent research work, we herein report the use of modified supramolecular host cyclodextrin as an effective solid based green catalyst for accessing structurally diverse and medicinally relevant pyrimidone architectures. The catalyst and the synthesized compounds 4 (a-r) were characterized using FT-IR, NMR and GC-Mass spectroscopy. Major highlights of the reported work include: atom economical process, extremely milder reaction conditions, operational simplicity, high isolated yields, and excellent catalyst turnover number. The molecular docking studies suggest that the compound 4n has the hydrogen bonding, hydrophobic and π-pair interactions with the active site of active sites of CXT M 15 receptor.

The use of Lactic Acid Bacteria (LAB) for probiotic enrichment of minimally processed fruit is a well-established practice in literature. In addition, several LAB demonstrated a strain-specific ability to control harmful microorganisms and decay agents, improving shelf-life, maintaining quality and promoting the safety of fruits and vegetables. Edible coatings can help modulate phenomena of gas exchange and water loss by fruits, representing protection from physical damage and spoilage phenomena linked to oxidation and the development of undesired microorganisms. At the same time, the coating can represent an innovative delivery matrix for the LAB strains of potential interest to improve safety and quality in the postharvest management of fruits. In this work, five Lactiplantibacillus plantarum strains, previously characterized for their probiotic and antifungal activity, have been incorporated into a sodium alginate coating to develop edible probiotic coatings with antifungal properties for table grapes cv. Italia. The transfer of probiotics and their survival were evaluated by comparing coated and uncoated table grapes during 14 days of cold storage at 4 °C. The alginate edible coating increased the number of probiotics transferred to the surface of the berries from about 5 to more than 7 Log CFU/g, with a crucial impact on the potential functional attributes of the final product. The ability of the functionalised coatings to counteract the decay development was evaluated on table grapes berries artificially contaminated with Aspergillus niger CECT 2805. A significant reduction of lesion diameter was observed in alginate coating with L. plantarum 11-A. The lesion diameter reduction was also accompanied by the reduction of the symptoms of infection, such as browning around the wound. These results suggest the application of selected strains of L. plantarum as promising bio-resources to enhance the overall value of ready-to-eat fruits and vegetables, particularly in combination with edible coating as a carrier matrix. While a strain-dependent effect was not detected with respect to the improvement of the number of cells in the edible coating, a variability depending on the biotype used was detected for the properties linked to biocontrol, suggesting that the inclusion in edible packaging may represent an innovative criterion in the selection of lactobacilli to be applied postharvest.

Silybin is a natural compound extensively studied for its hepatoprotective, neuroprotective and anti-cancer properties. Envisioning the enhancement of silybin potential by suitable modifications in its chemical structure, here, a series of new 7-O alkyl silybins derivatives were synthesized by Mitsunobu reaction starting from the silybins and tyrosol-based phenols, such as tyrosol (TYR, 3), 3-methoxytyrosol (MTYR, 4) and 3-hydroxytyrosol (HTYR, 5). This research sought to explore the antioxidant and anticancer properties of new eighteen derivatives and their mechanisms. In particular, the antioxidant properties of new derivatives outlined by DPPH assay, showed a very pronounced activity depending on the tyrosyl moiety (HTYR&gt;MTYR&gt;&gt;TYR). A significant contribution of the HTYR moiety was observed for silybins and 2,3-dehydro-silybin based derivatives. According to the very potent antioxidant activity, 2,3-dehydro-silybin derivatives 15ab, 15a and 15b exerted the most potent anticancer activity in human prostate cancer PC-3 cells. Furthermore, flow cytometric analysis for cell cycle and apoptosis revealed that 15ab, 15a and 15b induce strong G1 phase arrest and increase late apoptotic population in PC-3 cells. Additionally, western blotting for apoptotic marker cleaved caspase-3 confirmed apoptosis induction by these silybin derivatives in PC-3 cells. These findings hold significant importance in the investigation of anticancer properties of silybin derivatives and strongly encourage swift investigation in pre-clinical models and clinical trials.

Sustainable food consumption has attracted a widespread attention during last decades by scholars, policy makers and consumers. In line with this, farmers’ markets (FMs) have the potential to encourage sustainable agricultural production and consumption. By reducing the number of actors and distances along the food chain, these alternative food systems foster the reconnection between farmers and consumers and contribute to different social, economic and environmental sustainable goals. This paper provides insights on the role of consumers' sustainability concerns related to their motivation for shopping at FMs. By means of a choice experiment, we analyze the determinants of consumers’ WTP for buying apples at FMs. We are particularly interested in understanding how attitudes towards the three sustainability dimensions are related to consumer preferences in this context. We find that consumer attitudes towards direct contact with producers, contributing to farmers’ income, and environmental benefits can be directly related to product characteristics that are specific to FMs.

The importance of measuring sustainability in tourism has been significantly advancing in recent years, following the need to manage the impact of tourism on territories and hosting communities. It was further boosted by the pandemic, where sustainability has been defined as one of the central elements to restart global tourism. The ETIS model, developed by the European Commission, is a point of reference based on self-assessment, data collection and analysis by the destinations themselves. The application of ETIS toolkit has faced many challenges, especially at sub-national level, mostly related to the lack of available and updated data to feed the model. The hypothesis explored by the authors is to solve the implementation issues, developing an indicator based on the use of the Sentiment Analysis to frame e-reputation and tourism satisfaction, and further combining it with other open data sources. The Tourism Sustainability Index (TSI) can provide a scalable and geo-referenced evaluation of tourism sustainability, measuring the four pillars and sub-components referenced to ETIS criteria, applicable to any tourism destination. Results show that the TSI can be seen as a consistent and valid tool for destinations to analyze sustainability, monitor its evolution through time periods and sub-areas, and compare it to other benchmark or competitive areas.

The basic constitutional freedoms and rights of a person and citizen are in principle unlimited: the full scope of their exercise is the rule, and the restriction determined by law can only be an exception based on explicit constitutional authority and the legitimate aim of the restriction determined by the Constitution. That being so, the restrictions - in addition to being based on constitutional authority and pursuing constitutional objectives - should be commensurate with the needs to achieve these objectives. This means that restrictive legal rules must be suitable for achieving the legitimate aim pursued, must not be stricter than necessary and must be balanced between the constitutionally guaranteed subjective right of the individual and the interests of society. In this scholar paper, the authors point out the economic and legal consequences of the violation of individual privacy and data protection rights caused by the public disclosure of personal data of people who, at a certain time, were obliged to self-isolate due to suspicion of Covid-19 virus infection.

The abilities of quantitative description of noise are restricted due to its origin and only the statistical and spectral analysis methods can be applied while an exact time evolution cannot be defined or predicted. It emphasizes the challenges faced in many applications including communication systems where noise can play, on one hand, a vital role impacting signal-to-noise ratio but possessing, on the other hand, unique properties such as infinite entropy (infinite information capacity), exponentially decaying correlation function and so on. Despite the deterministic nature of chaotic systems, the predictability of chaotic signals is limited for a short time window putting them close to random noise. In this article, we propose and experimentally verify an approach to achieve Gaussian-distributed chaotic signals by processing the outputs of chaotic systems. The mathematical criteria, on which the main idea of the study is based on, is the Central Limit Theorem which states that the sum of a large number of independent random variables with similar variances approaches a Gaussian distribution. The study involves more than 40 mostly three-dimensional continuous-time chaotic systems (Chua’s, Lorenz’s, Sprott’s, memristor-based, etc.) whose output signals are analyzed according to criteria that encompass the probability density functions of a chaotic signal itself and its envelope and phase, statistical and entropy-based metrics such as skewness, kurtosis, and entropy power. We found that two chaotic signals of Chua’s and Lorenz’s systems exhibited superior performance across the chosen metrics. Furthermore, our focus extended to determining the minimum number of independent chaotic signals necessary to yield a Gaussian-distributed combined signal. The analytic and experimental results indicate that the sum of at least three non-Gaussian chaotic signals closely approximates Gaussian distribution. It allows generation of reproducible Gaussian-distributed deterministic chaos by modeling simple chaotic systems.

The study of different forms of preconditioners for solving a system of nonlinear equations, by using Newton’s method, is presented. The preconditioners provide numerical stability and rapid convergence with reasonable computation cost, whenever chosen accurately. Different families of iterative methods can be constructed by using a different kind of preconditioners. The multi-step iterative method consists of a base method and multi-step part. The convergence order of base method is quadratic and each multi-step add an additive factor of one in the previously achieved convergence order. Hence the convergence of order of an m-step iterative method is m + 1. Numerical simulations confirm the claimed convergence order by calculating the computational order of convergence. Finally, the numerical results clearly show the benefit of preconditioning for solving system of nonlinear equations.

The European Union's recent decision to renew the authorization for the use of glyphosate until 15 December 2033 stimulates the scientific discussion all around the world regarding its toxicity or otherwise for humans. Glyphosate is a chemical used by millions of tons in the last 50 years worldwide to drying weeds in cultivated fields, greenhouses, roadsides. Concern has been raised in many quarters about the possible presence in the food chain and the consequent adverse effects on health: both aspects that argue in favor of toxicity and those that instead may indicate limited toxicity of glyphosate are here discussed. The great debate that has been generated requires further investigations and field measurements to understand its fate once dispersed in the environment and its concentration in the food chain. Hence the need for validated analytical methods that are available to analysts in the field. In the present review, methods for the analytical determination of glyphosate and its main metabolite, AMPA, are discussed, with a specific focus on chromatographic techniques applied to cereal products. The experimental procedures are explained in any detail, including cleanup, derivatization, and instrumental conditions to give the laboratories involved enough information to proceed with the implementation of this line of analysis. The prevalent chromatographic methods used are LC-MS/MS, GC-MS/SIM, and GC-MS/MS but sufficient indications are also given to those laboratories that wish to use the simpler HPLC-FLD, HPLC-UV, GC-NPD or GC-FPD techniques for screening purposes. Concentrations from literature measured in wheat, corn, barley, rye, oats, soybean, and cereal-based foods are reported together with the regulatory status in various parts of the world and the accumulation mechanism. As for the accumulation in cereals, available data show that glyphosate tends to accumulate more in wholemeal flours than in refined ones, that its concentration in the product strictly depends on the treatment period (the closer it is to the time of harvesting, the higher the concentration) and that in cold climates the herbicide tends to persist in the soil for a long time.

A Brewer Spent Grain (BSG), the most abundant by-product of the brewing process, is mainly used in animal feed and biogas production. The aim of the present work is BSG valorization by yeast fermentation to produce carotenoids. R. mucilaginosa CBS316 was cultured on BSG syrups, supplemented or not with YE and PEP (s-Fsa and Fsa). The biomass and carotenoid production were optimized in flasks and then scaled-up in bioreactor. In flask tests, the maximum biomass concentration was 5.3 and 6.2 g/L for Fsa and s-Fsa cultures, respectively. The maximum carotenoid production was 833 μg/L in Fsa and 1159 μg/L in s-FSA. Considering that the highest specific productivity value (P 7.16 μg/g*h) was obtained with Fsa syrup, this medium was selected for the process scale-up. In bioreactor tests, the maximum concentrations of biomass (4.29 g/L) and carotenoid (396 ug/L) was reached at 72 hours of fer-mentation, 24 h later than in flask. The total carotenoid produced was 524 and 150 ug in bioreactor and flask cultures, respectively. The carotenoids production by R. mucilaginosa was obtained both in Fsa and s-Fsa syrups. The results confirm the possibility to use the syrup as it is, Fsa, thus limiting the process costs.

The method for quantitative analysis is based on the direct measurement of the analyte using differential pulse voltammetry (DPV), exploiting its oxidation peak. Calibration curves are set up to evaluate the figures of merit of the analytical method (LOD, LOQ, linear range). The application of the sensor for the dosing of GA in real matrices is carried out by analyzing non-alcoholic and alcoholic beverages and comparing the results with those reported in the literature and with the content of total polyphenols determined by the Folin-Ciocalteu method. In all cases, concentrations of GA align with those previously found in the literature for the beverages examined. Moreover, the values are always lower than the total polyphenols content; this demonstrates the good selectivity of the sensor that can discriminate the target molecule from other polyphenols present.

The essay focuses, from a sociological perspective, on the phenomenon of depopulation of Inner Areas in Italy. In this areas, younger generations, live a great inequality that exposed them to risk of social vulnerability. So, on the one hand, the desire to leave their community is growing among younger, on the other hand, the desire to deal with extreme adverse conditions is falling down. The research aims to explore the depopulation phenomenon in the context of Southern Italy, considering it as an emerging social vulnerability that impacts very deeply onto the sustainability of a social, economic and community systems such as the Molise region one. The following paper therefore presents an empirical web-survey conducted in the Molise region. The methodology used is Quantitative, and the research design is Exploratory. The essay underlines how proximity welfare can act as a flywheel to counter the depopulation Inner Areas of Italy enacted by the younger generations.

Azo dyes are the most widely used synthetic dyes in the printing and dyeing process. However, the discharge of untreated azo dyes poses potential threat for human health and aqueous ecosystem. Herein, we fabricated a novel heterogenous catalyst - activated carbon fiber-supported ferric alginate (FeAlg-ACF) . Together with peroxymonosulfate (PMS) and visible light, this photocatalytic oxidation system was used to remove an azo dye - azophloxine. The results indicated that the proposed catalytic oxidation system can remove 100% azophloxine within 24 min, while under the same system, the removal rate was only 92 % and 84 % when ferric alginate was replaced with ferric citrate and ferric oxalate respectively, which showed the superiority of activated carbon fiber-supported ferric alginate. The degradation of azophloxine is achieved by the active radicals (SO4•− and •OH) released from PMS and persistent free radicals from activated carbon fiber. After treating for 24 min, the total organic carbon of azophloxine solution (50 μmol/L) decreased from 1.82 mg/L to 79.3 μg/L and the nitrate concentration of ions increased from 0.3 mg/L to 8.6 mg/L. That is, up to 93.5% azophloxine molecules were completely degraded into inorganic compounds. Consequently, potential secondary contamination by intermediate organic products during catalytic degradation was prohibited. The azophloxine removal ratio was kept almost constant after seven cycles, indicating the recyclability and longevity of this system. Furthermore, the azophloxine removal was still promising at high concentrations of Cl-, HCO3-, CO32-. Therefore, our proposed system is potentially effective to remove dye pollutants from seawater. It provides a feasible method for the development of efficient and environmental friendly PMS activation technology combined with FeAlg-ACF, has significant academic and application value.

The gastrointestinal tract is colonized by trillions of different microorganisms, named the gut microbiota, which is key to degrade undigested food such as dietary fibers. The fermentation of these food components leads to the production of short-chain fatty acids (SCFA) acetate, propionate, and butyrate, which exploit several beneficial roles for the host’s health. Their production and absorption happen in different ways in the human intestine and depend on the type of dietary fiber reaching the gut and the microorganisms involved in the fermentation. The supplementation of SCFAs, mostly butyrate, in treating gastrointestinal, metabolic, cardiovascular, and gut-brain-related diseases has been reported in the medical literature. This review aims to give an overview of the production and absorption dynamics of acetate, propionate, and butyrate in the human gut, with a final focus on the role played by these SCFAs on gastrointestinal and metabolic health and the present therapeutic implications.

A number of studies suggested that influenza vaccination can provide protection against COVID-19 but the underlying mechanisms that could explain this association is still unclear. In this study, the effect of the 2021/2022 seasonal influenza vaccination on the immune response to the booster dose of anti-SARS-CoV-2 vaccination was evaluated in a cohort of healthy individuals. One hundred and thirteen participants were enrolled, and 74 of them with no prior COVID-19 diagnosis or significant co-morbidities were considered for the analysis. Participants received the anti-influenza tetravalent vaccine and the booster dose of the anti-SARS-CoV-2 vaccine or the anti-SARS-CoV-2 vaccine alone. Blood was collected before and 4 weeks after each vaccination and 12 weeks after SARSCoV2 vaccination and analyzed for anti-flu and anti-spike-specific antibody titers and for in vitro influenza and SARS-CoV-2 neutralization capacity. Results indicated an increased reactivity in subjects who received both influenza and SARSCoV2 vaccinations, as compared to those who received only the SARS-CoV-2 vaccine, with sustained anti-spike antibody titers up to 12 weeks post-vaccination. Immune response to influenza vaccine was evaluated and individuals were stratified as high or low responders. High responders showed increased antibody titers against SARSCoV2 vaccine both after 4- and 12-weeks post-vaccination. On the contrary, the individuals classified as low responders were less responsive to the SARS-CoV-2 vaccine. These data indicate that both external stimuli, such as influenza vaccination, and the host's intrinsic ability to respond to stimuli play a role in the response to vaccine.

Food-borne transmission is a recognized route for many viruses associated with gastrointestinal, hepatic or neurological diseases. Therefore, it is essential to identify new bioactive compounds with broad-spectrum antiviral activity is needed to exploit innovative solutions against these hazards. Lately, antimicrobial peptides (AMPs) have been recognized as promising antiviral agents. Indeed, while the antibacterial and antifungal effects of these molecules have been widely reported, their use as potential antiviral agents has not yet been fully investigated. Herein, the antiviral activity of previously identified or newly designed AMPs, was evaluated against the non-enveloped RNA viruses, Hepatitis A virus (HAV), and Murine Norovirus (MNV), a surrogate for human Norovirus. Moreover, specific assays were performed to recognize at which stage of the viral infection cycle the peptides could function. Results showed that almost all peptides displayed virucidal effects with about 90% of infectivity reduction on HAV or MNV. However, the decapeptide RiLK1 demonstrated, together with its antibacterial and antifungal properties, a notable reduction in viral infection for both HAV and MNV, possibly through direct interaction with viral particles or inhibition of the viral bonding to the cell receptors. Hence, RiLK1 could represent a versatile ‘antimicrobial agent effective against various foodborne pathogens including viruses, bacteria, and fungi.

Melasma is a challenging skin condition which involves both structural and functional skin alterations. Despite the availability of various treatment options, the management remains complex. This is the first study to investigate topical application of Rosa Damascena stem cell exosomes when used concomitantly with microneedling in women and men with facial melasma. We recruited 20 subjects with Fitzpatrick skin types I-III, exhibiting melasma of varying severity. The modified Melasma Area and Severity Index (mMASI) and Global Aesthetic Improvement Scale (GAIS) were utilized to evaluate treatment response. The treatment protocol involved microneedling followed by exosome application over four or five sessions, at 4-week intervals. Ninety percent of subjects demonstrated a significant improvement in mMASI scores, while only 10% showed no change. GAIS assessment further supports overall improvement, with just 10% categorized as "not changed". Tolerability was favorable, with mild, transient side effects. Our findings suggest promising outcomes with this combined therapy, underscoring its potential as a safe and effective approach for treating melasma, particularly in severe and moderate cases. However, further research with larger sample sizes and control arms is warranted to validate these findings and explore long-term efficacy.