Blood image intensity has been used to detect erythrocyte sedimentation rate (ESR). However, it does not give an information on biophysical properties of blood sample under continuous ESR. In this study, three physical properties, including, τ₀, ESR_τ, and AI_I, are suggested to quantify mechanical variations of blood under continuous ESR. To demonstrate the proposed method, blood sample is loaded into a driving syringe. The blood flow rate is set in a periodic on–off pattern. Blood sample is then supplied into a capillary chip, and microscopic blood images are captured at specific intervals. Blood shear stress is quantified from the interface of blood stream in the coflowing channel. Both τ₀ and ESR_τ are then obtained by analyzing the blood shear stress. Simultaneously, the AI_I is evaluated by analyzing the image intensity of blood flow. According to the experimental results, the τ₀ exhibits consistent trends with respect to hematocrit as well as diluent. The ESR_τ and AI_I showed a reciprocal relationship each other. Three suggested properties represented substantial differences for suspended blood samples (i.e., hardened red blood cells, different concentration of dextran solution and fibrinogen). In conclusion, the present method can detect variations of blood sample under continuous ESR effectively.

Evaluating soil quality across various altitudinal gradients, both with and without vegetative cover, is crucial for the proper functioning of soil and optimal crop growth, thereby contributing to the sustainability of agroecosystems. Although the altitudinal gradient significantly influences soil quality, the ability to predict this quality, expressed through an index, in soils with and without vegetative cover, is still insufficiently explored. This study aimed to assess soil quality in the Jun Jun micro-watershed, located in the Tungurahua region, Ecuador. To achieve this objective, three categories of altitudinal gradients were selected: less than 2800 meters above sea level (masl), between 2800 and 2900 masl, and greater than 2900 masl. A total of 24 soil samples were collected in the mentioned gradients, considering both areas with and without vegetative cover. The indicators used included chemical and biological parameters such as soil organic carbon (OC), earthworm density (WD), earthworm biomass (WB), organic matter (OM), pH, total nitrogen (TN), and organic carbon (OC). The results revealed that in areas with altitudinal gradients below 2800 masl, soil quality index values were higher compared to other altitudes. In vegetated areas, a decrease in index values was observed as the altitudinal gradient increased, indicating a deterioration in soil quality with altitude. These findings are significant in providing a quantitative assessment of the effects of altitudinal gradient and vegetative cover influence on soil quality.

The low relative humidity (RH) levels in a greenhouse during the daytime in a strawberry (Fragaria × ananassa Duch) cultivation period negatively affect the growth of strawberry related to photo-physiology. Therefore, this study was conducted to confirm an efficient RH management method by analyzing the phenotypic characteristics related to photo-physiology by controlling the RH in a greenhouse during the daytime with a fog system. Strawberry plants were grown respectively in a greenhouse affected by natural RH changes (control) and in a greenhouse with 40% ~ 50% RH adjusted during the daytime using a fog system. In the greenhouse, with controlled RH, the temperature decreased, and the RH was higher in the initial growth stage of strawberry planting than the control. It was observed a significant increase in the survival rate of the strawberry plant, as well as the incidence of powdery mildew, was lowered. In addition, the photosynthetic rate and OJIP chlorophyll a fluorescence transients related to photosystem II efficiency of strawberry leaves were significantly higher in the fog treatment than in the control. In winter, during the day, the number of days on which the temperature dropped below 20℃ has increased, the greenhouse temperature with controlled RH was lower due to the fog system. When the yield per strawberry plant in January and February was investigated, the control was higher than the RH treatment. Therefore, RH management using a fog system must be controlled at a level where a temperature range is adequate for plant growth, in which the efficient control of these parameters increases strawberry productivity.

Recent progress in the fabricating flexible electronics has been developed significantly due to the increased interest of the flexible electronics which can be applied to enormous fields not only to conventional electronic devices but to bio/eco electronic devices. Flexible electronics can be applied to wide range of fields such as flexible display, flexible power storage, flexible solar cells, wearable electronics and healthcare monitoring devices. Recently, flexible electronics are being attached on the skin and even implanted into human body to monitor the bio-signals and for treatment purpose. To improve the electrical characteristic and the mechanical properties of flexible electronics, nanoscale fabrications using novel nano-materials are required. Advanced in nanoscale fabrication methods allow construction of the active materials that can combine with the ultra-thin soft substrate to form flexible electronics with high performances and reliability. In this review, wide range of nanoscale fabrication methods for flexible electronics classified in either top-down or bottom-up approaches such as conventional photolithography, soft lithography, nanoimprint lithography, growth, assembly and chemical vapor deposition(CVD) will be reported with specific fabrication processes and results. Here, our aim is to introduce various fabrication methods that can be used to fabricate the flexible electronics.

Knowledge graphs (KGs) play a crucial role in many applications, such as question answering, but incompleteness is an urgent issue for their broad application. Much research in knowledge graph completion (KGC) has been performed to resolve this issue. The methods of KGC can be classified into two major categories: rule-based reasoning and embedding-based reasoning. The former has high accuracy and good interpretability, but a major challenge is to obtain effective rules on large-scale KGs. The latter has good efficiency and scalability, but it relies heavily on data richness and cannot fully use domain knowledge in the form of logical rules. We propose a novel method that injects rules and learns representations iteratively to take full advantage of rules and embeddings. Specifically, we model the conclusions of rule groundings as 0-1 variables and use a rule confidence regularizer to remove the uncertainty of the conclusions. The proposed approach has the following advantages: 1) It combines the benefits of both rules and knowledge graph embeddings (KGEs) and achieves a good balance between efficiency and scalability. 2) It uses an iterative method to continuously improve KGEs and remove incorrect rule conclusions. Evaluations on two public datasets show that our method outperforms the current state-of-the-art methods, improving performance by 2.7% and 4.3% in mean reciprocal rank (MRR).

Convolutional neural networks (CNNs) face challenges in capturing long-distance text correlations, and Bidirectional Long Short-Term Memory (BiLSTM) networks exhibit limited feature extraction capabilities for text classification of work order. To address the abovementioned problems, this work utilizes an ensemble learning approach to integrate model elements efficiently. This study presents a method for classifying work order texts using a hybrid neural network model called BERT-BiLSTM-CNN. First, use Bert for preprocessing to obtain text vector representations. Then, capture context and process sequence information through BiLSTM. Next, capture local features in the text through CNN. Finally, obtain classification results through Softmax. Through comparative analysis, the method of fusing these three models is superior to other hybrid neural network model architectures in multiple classification tasks. It has a significant effect on work order classification.

Space tourism began in 2001 and became popular in 2021 because of commercial operations. With the development of space technology and commercialization, like re-launchable rockets to travel to space in recent years, it has gradually entered the era of space. However, the space industry causes massive emissions, inducing some opposition to its development. It is essential to investigate the attitude of residents toward space tourism and balance the pros and cons of sustainability. Quantitative analysis was adapted to test two models based on duality theory. The data were obtained from 284 samples from various regions of China and analyzed using the partial least squares structural equation modeling (PLS-SEM). The results show that the two-factor model of economic development conflicted with environmental protection. However, study two indicates that educational interventions can facilitate sustainable space tourism because they mediate the relationship between economic and environmental factors.

The controllability and consistency in the fabrication of micro-textures on large-scale remains a challenge for existing production processes. Mask electrolyte jet machining (MEJM) is an alternative to Jet-ECM for controllable and high-throughput surface microfabrication with more consistency of dimensional tolerances. This hybrid configuration combines the high-throughput of masked-ECM and the adjustable flow-field of jet-ECM. In this work, a duckbill jet nozzle was introduced to make MEJM more capable of batch micro-structuring. A multiphysics model was built to simulate the distribution of electrochemical reaction ions, the cur- rent density distribution and the evolution of the shape of the machined cavity. Experimental investigations are presented showing the influence of the machining voltage and nozzle moving speed on the micro cavity. Several 35 ×35 micro cavity arrays with a diameter of 24.92 − 11.73 µm and depth of 15.86 − 7.24 µm are generated on 304 stainless steel.

This study examines the influences of live streaming servicescape on Chinese consumers' luxury purchase intention. Interestingly, for the sample without luxury purchase experience, the mediating effect of the perceived value of luxury goods is significant but effect of consumer trust is not. For the sample with luxury purchase experience, the result of mediating effect is just the opposite. The interaction between conspicuous consumption and live streaming servicescape plays a certain role in regulating the perceived value of luxury goods. These results show that luxury brands can adopt innovation in the live streaming servicescape for different types of consumers to promote live streaming marketing. This study enriches the servicescape theory of live streaming.

Due to wood’s susceptibility to fire, it is crucial to treat wood-based materials with flame retardants, especially in construction applications. This study investigated the effectiveness of various grooving types, including transverse, longitudinal, both transverse and longitudinal, and surface grooving, in enhancing larch's vacuum pressure impregnation process. The results revealed that transverse grooving provided a slightly greater impregnation advantage than longitudinal grooving. Moreover, exceptional impregnation performance was observed in larch samples subjected to both longitudinal and transverse grooving and surface grooving, exhibiting a remarkable improvement of 214,7 % compared to untreated larch.

A nanocomposite rod-shaped structure with single-walled carbon nanotube (SWCNT) embedded in polypyrrole (PPy) doped with nonafluorobutanesulfonic acid (C4F), SWCNT/C4F-PPy, was synthesized using emulsion polymerization. The hybrid ink was then directly coated on a polyimide film interdigitated with the Cu/Ni/Au electrodes via a screen-printing technique to create a flexible film sensor. The sensor film showed a response of 1.72% at 25 °C/atmospheric pressure when acetone gas of 5 ppm was injected, which corresponds to almost 95% compared to the Si wafer-based array interdigitated with the Au electrode. Additionally, C4F was used as a hydrophobic dopant of PPy to improve the stability of humidity and to produce a highly sensitive film-type gas sensor that provides stable detection even in humid conditions.

Globally,coastal regions are vital areas of human activities and, as such, are centres of population growth and urban and economic development. Long-term human development has had a major impact on the ecological environment of coastal zones. Therefore, exploring the distribution and provenance of marine sediment types in coastal areas heavily influenced by human activities can provide scientific evidence and references for the current and future ecological management of these sensitive environments. For this reason, we have conducted an analysis on the sediment grain size, Endmember, organic matter content and geochemical elements in the Lu’erhuan River‒Malan Island‒Sandun Island area in the eastern part of Qinzhou Bay, a region heavily influenced by human activities. Sediment grain size clearly differs throughout the study site and the material provenances and hydrodynamic conditions are also varied, likely due to the local environmental conditions and the significant impact human activities have had on the area. The finest-grained sediment is imported from either inland or coastal areas via rivers and weak tidal currents, the next finest component is input from coastal areas through weak tidal currents, and the moderately coarse component mainly originates from nearby beaches. The two coarsest-grained sediment components are influenced by the combination of human activities, tidal currents and waves and enter the water via erosion. Organic matter provenance resembles that of the sediment components, exhibiting varied characteristics. This is due to the combination of natural and human activities in the bay. The organic matter in the upper reaches of the Lu’erhuan River originates from the river and coastal paddy fields, with obvious terrigenous characteristics; the organic matter in northern Malan Island mainly comes from external sources related to oyster farming; while organic matter in eastern Sandun Island is mainly produced endogenously by marine plankton. Al, Ti, Fe, Mg, K, Ga and other elements indicate that terrestrial sediments are significantly disturbed by human activities. However，Mn reflects the marine distribution of terrestrial sediments from the Lu’erhuan River to Jishuimen. Ca and Sr, indicators of marine sediments, are distributed in the eastern offshore area of Sandun Island, which is connected to the open waters. Due to the influence of human activities, As and Cd are highly enriched in the study area, while Cu is less affected by human activities.

The combination of wet-lab experimental data on multi-site combinatorial mutations and machine learning is an innovative method in protein engineering. In this study, we present an improved innovative sequence–activity relationship (innov'SAR) methodology based on novel descriptors and digital signal processing (DSP) to construct a predictive model. In this improved approach, 21 experimental (R)-selective amine transaminases from Aspergillus terreus (AT-ATA) were used as an input to predict higher thermostability than that predicted using the existing data. We successfully improved the determination coefficient (R2) of the model from 0.66 to 0.92. In addition, root mean square deviation (RMSD) and root mean square fluctuation (RMSF) were estimated and conformation analysis based on molecular dynamics simulations was performed to verify the enhanced thermal stability of the screened mutants. The improved innov'SAR algorithm enhanced the predictive accuracy, suggesting a method for modifying the stability of AT-ATA, which may help in directed evolutionary screening and open up new avenues for protein engineering.

In the context of high-temperature water vapor treatment, Zn-Mg-Al alloy-coated steel sheets exhibit the emergence of a black surface. This study aims to explore the factors and mechanisms contributing to surface blackening by inducing black surfaces on Zn-Mg-Al alloy-coated steel sheets, which were fabricated through molten coating subjected to water vapor treatment at 150 degrees Celsius. The surfaced composition was predominantly identified as ZnO, a zinc oxide film, validated through X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). Morphological analysis of the surface and cross-section post-water vapor treatment revealed a disrupted lamellar structure with diffused features, resulting in the formation of an oxide film. Optical properties analysis demonstrated an increased absorbance and a decreased bandgap energy after water vapor treatment, indicative of an augmented blackening effect. Consequently, the high-temperature water vapor treatment led to the formation of oxides on the surface, with the highly reactive Mg and Al extracting oxygen from the predominantly present ZnO surface. This process resulted in the creation of an oxygen-deficient oxide, ultimately causing surface blackening.

We study latching dynamics in the adaptive Potts model network, through numerical simulations with randomly and also weakly correlated patterns, and we focus on comparing its slowly and fast adapting regimes. A measure, Q, is used to quantify the quality of latching in the phase space spanned by the number of Potts states S, the number of connections per Potts unit C and the number of stored memory patterns p. We find narrow regions, or bands in phase space, where distinct pattern retrieval and duration of latching combine to yield the highest values of Q. The bands are confined by the storage capacity curve, for large p, and by the onset of finite latching, for low p. Inside the band, in the slowly adapting regime, we observe complex structured dynamics, with transitions at high crossover between correlated memory patterns; while away from the band latching transitions lose complexity in different ways: below, they are clear-cut but last so few steps as to span a transition matrix between states with few asymmetrical entries and limited entropy; while above, they tend to become random, with large entropy and bi-directional transition frequencies, but indistinguishable from noise. Extrapolating from the simulations, the band appears to scale almost quadratically in the p - S plane, and sublinearly in p - C. In the fast adapting regime the band scales similarly, and it can be made even wider and more robust, but transitions between anti-correlated patterns dominate latching dynamics. This suggest that slow and fast adaptation have to be integrated in a scenario for viable latching in a cortical system. The results for the slowly adapting regime, obtained with randomly correlated patterns, remain valid also for the case with correlated patterns, with just a simple shift in phase space.

Acoustic emission (AE) is caused by the sudden release of energy by a material as a result of material degradation related to deformation, crack, or fault within a solid. The same situation also occurs in leaks caused by turbulence in the fluid around the leak. In this study, analytical modeling for AE due to leakage through a circular pinhole in a gas storage cylinder was performed. The displacement fields responsible for AE, excited by the concentrated force (CF) associated with the turbulent flow though the pinhole, were derived by solving the Navier-Lamé equation. The CF as an excitation source was formulated in terms of a fluctuating Reynolds stress (FRS) and spatial Green’s function. In particular, a series of experiments were conducted under different operating conditions to explore the characteristics of the AE signals due to leak in a gas cylinder. Finally, the simulation and experimental results were compared to verify the accuracy of the simulation results.

: Cnidium officinale Makino, a perennial crop in the Umbeliperae family, is harvested in the summer for medicinal purposes. The average temperature in Korea has recently increased, and consequently, the area used to cultivate C. officinale has been reduced, and plant disease and soil sickness have increased. In this study, rhizosphere bacteria were isolated from C. officinale, and their antagonistic activity evaluated against Fusarium solani, which is a major issue during repeated cultivation. Twenty-eight strains were isolated from the root and rhizosphere soil, of which seven showed antagonistic activity against F. solani and were further investigated. An in planta test found that the dead rate of shoots was significantly lower in the group inoculated with PT1 isolated from the root tissue and that the fresh and dry weights were also higher, when compared with the other groups. PT1 was thus considered to have antagonistic activity against F. solani. The 16S rRNA analysis identified the PT1 as Leclercia adecarboxylata, and downstream studies confirmed the production of enzymes related to antagonism, such as siderophore and N-acetyl-β-glucosaminidase. The phosphorous solubilizing ability and secretion of related enzymes were also confirmed. The results indicate that PT1 could be utilized as a PGPR to help control fusarium wilt.

An all-dielectric metasurface composed of orthogonal-slit silicon disks is proposed in this study. By modifying the unit structure of the metasurface with the bound states in the continuum (BIC) theory, a sharp Fano resonance can be generated. The resonance properties of the metasurface are investigated by analyzing the effects of the structural parameters on the resonance using the eigenmode analysis method. The Q factor and the resonance wavelength can be adjusted by varying the slit width, the disk thickness, and the disk radius. The electromagnetic characteristics and mechanism of the toroidal dipole-BIC (TD-BIC) are explored in depth through an analysis of the multipole expansion of the scattered power, along with the electromagnetic field and the current distribution at resonance. This research provides a novel approach for excitation of a strong TD-BIC resonance and proposes potential applications in optical switches, high-sensitivity optical sensors, and related areas.

To assess the usefulness of an attachable video laryngoscope (AVL) by attaching a camera and monitor to a conventional Macintosh laryngoscope (CML). Normal and tongue edema airway scenarios were simulated using a manikin. Twenty physicians performed tracheal intubations using CML, AVL, Pentax AWS® (AWS), and McGrath MAC® (MAC) in each scenario. Ten physicians with more than 10 cases of clinical experience with tracheal intubation using CML were included in the skilled group. Ten physicians with less than 10 cases of clinical experience with tracheal intubation using CML were included in the unskilled groups. The time required to intubate and the success rate were recorded. The degree of difficulty of use and glottic view assessment scored by participants. All 20 participants successfully completed the study. There was no difference in the success rate and time required for tracheal intubation in the normal airway scenarios. For the skilled group, in the tongue edema airway scenario, the AWS had the highest success rate (100%) followed by AVL (60%), MAC (60%), and CML (20%) (p = 0.001). The time required to intubate with the AWS was significantly shorter than with AVL (10.2 vs 22.3 s; p=0.002) or MAC (10.2 vs 23.7 s; p=0.001). There was no significant (p > 0.05) difference between AVL and MAC. The degree of Difficulty of Use for AVL was significantly lower than that for CML (7.8 vs 2.8; p < 0.001). There was no significant (p > 0.05) difference between AVL and other video laryngoscopes. AVL had a higher rate of successful tracheal intubation than CML in the tongue edema scenario. AVL showed a similar success rate and time of tracheal intubation to the MAC. Therefore, AVL may be a possible alternative video laryngoscope device.

The present study was conducted to investigate the effects of rhizome extract of Dioscorea batatas (Dioscoreae Rhizoma, Chinese Yam) and its bioactive compound, allantoin, on myoblast differentiation and mitochondrial biogenesis in skeletal muscle cells. Yams were extracted in water and the extract was analyzed by HPLC. The expression of C2C12 myotubes differentiation and mitochondrial biogenesis regulators were determined by reverse transcriptase (RT)-PCR or Western blot. The glucose levels and total ATP contents were determined by glucose consumption, glucose uptake and ATP assays, respectively. Treatment with yam extract (1 mg/mL) and allantoin (0.2 and 0.5 mM) significantly increased of MyHC expression compared with non-treated myotubes. Yam extract and allantoin significantly increased the expression of mitochondrial biogenesis regulating proteins, PGC1?, Sirt-1, NRF-1, and TFAM, as well as the phosphorylation of AMPK and ACC in C2C12 myotubes. Furthermore, yam extract and allantoin significantly increased the glucose uptake levels and the ATP contents. Finally, HPLC analysis revealed that the yam extract contained 1.53% of allantoin. Yam extract and allantoin, stimulated myoblast differentiation into myotubes and increased energy production through upregulation of mitochondrial biogenesis regulators. These findings indicate that yam extract and allantoin can help to prevent the skeletal muscle dysfunction through stimulation of energy metabolism.

The global shrimp farming industry is impacted by various infectious diseases, leading to marked production losses. Virulent Vibrio parahaemolyticus strains (VPAHPND) and other Vibrio species cause acute hepatopancreatic necrosis disease (AHPND) in shrimp. We isolated a binary toxin PirA/B-bearing V. campbellii strain (HJ-2023) from a Korean shrimp farm. The biochemical characteristics and antibiotic susceptibility of HJ-2023 were analyzed and compared to those of PirA/B-bearing VPAHPND. Non-AHPND-causing V. campbellii was the control. The pathogenicity of each strain was analyzed in white-leg shrimp. Phylogenetic analysis classified the isolated HJ-2023 strain as V. campbellii. Biochemical tests confirmed distinct properties of HJ-2023, compared to the genetically similar V. harveyi group. The AHPND-causing toxin gene of HJ-2023 showed 100% similarity to the rpoD gene of VCAHPND. An antibiotic disc susceptibility test indicated that HJ-2023 showed resistance to ampicillin, clindamycin, lincomycin, and erythromycin, which is effective against gram-positive bacteria, and showed weak sensitivity to gentamycin. Furthermore, HJ-2023 was 25% less toxic than VPAHPND but could be lethal during aquaculture-related outbreaks. These results highlight the complexity and virulence of AHPND-causing strains through multiple pathways and confirm the pathogenicity of V. campbellii, which increases the risk posed by AHPND to shrimp aquaculture. Our findings could help prevent AHPND.

Background: The role of preoperative serum carcinoembryonic antigen (sCEA) and postopeative tissue CEA (tCEA ) were widely elaborated separately for colorectal cancer (CRC). But the role of the combined sCEA and tCEA was scarcely described by now. Methods: 1757 cases of 0~ⅣCRC from January 2006 to January 2016 in our institution were involved. Clinicopathological features and follow up data were collected. 0 stage was combined into 0&Ⅰ stages. SCEA was classified to normal and high(>10ng/ml) and tCEA were classified into three grades (+,++,+++). So combined groups were six (2ⅹ3). ANOVA and Crosstab were used to analyze continuous and counting data, Univariate and multivariate were analyzed by Cox regression. All data were analyzed by SPSS27 and survival curves with number at risk were visualized by R 4.3.1. Results: Gender, age, tumor location, tumor size, blood loss, T stage, differentiation, harvested lymph nodes, positive lymph nodes, chemotherapy, TNM stage and complication have difference between the combined CEA test (all P

The economic development and infrastructure of a nation are closely interrelated. In addition, public trust in national infrastructure facilities is closely linked to the preservation of the advantages provided by these facilities to the public. Since the 1970s, Korea has achieved exponential economic growth over a short period of time and the number of infrastructure facilities has increased correspondingly. This compressed economic development has been underpinned by the national infrastructure, whose safety and usability have been excluded from the scope of the development. However, after around 30 years, structural deterioration coupled with general insensitivity to safety in today’s society has considerably reduced public trust in using the infrastructure. Realistically, policies that mainly focus on developing new technologies related to infrastructure construction have led to practical limitations that discourage the development of technologies for maintenance or inspection. Furthermore, current maintenance works face certain limitations caused by various reasons: insufficient budget, increasing number of infrastructure facilities requiring maintenance, shortage of manpower, and rapidly increasing number of aging infrastructure facilities. To overcome these limitations, a new approach is required that is different from general inspection methods under the existing rules and regulations. In this context, this study aimed to explore the efficiency of bridge inspection and maintenance by unmanned aerial vehicles (UAVs) that could observe inaccessible areas, could be conveniently and easily controlled, and could offer high economic benefits. To this end, various tests were performed on elevated bridges, and suitable UAV images were obtained. The obtained UAV images were inspected by using machine vision technology, thereby excluding subjective evaluations by humans. Methods for enhancing the objectivity of the inspection were also discussed. The test results showed that both the efficiency and objectivity of the proposed method were better than those of the existing bridge maintenance and inspection methods.

To eliminate the influence of the inconsistency on the cycle life and the available capacity of the battery pack, and improve the balancing speed, a novel inductor-based layered bidirectional equalizer (IBLBE) is proposed. The equalizer is composed of the bottom balancing circuits and the upper balancing circuits, and the two layer circuits both consist of a plurality of balancing sub-circuits, which allow the dynamic adjustment of equalization path and equalization threshold. The battery string is modularized by layered balancing circuits to realize fast active equalization, especially for long battery strings. By controlling the bottom balancing circuits, the individual cells can be balanced in each module. At the same time, the equalization between battery modules can be realized by controlling the upper balancing circuits. Simulation and experimental results demonstrate that the proposed equalizer can achieve fast active equalization for a long battery string, and has the characteristics of multi balancing path, large balancing current and high accuracy. The advantages of the proposed equalizer are further verified by a comparison with existing active equalizer.

As medical care aiming to maintain the quality of life for elderly patients is increases, implant treatment for elderly patients is increasing worldwide. Therefore, we aimed to investigate implant stability and the reliability of different measuring devices according to implant placement site and duration in patients aged over 65 years. The study evaluated 60 implants in 60 patients aged ≥ 65 years. The implant placement sites were divided into six evenly distributed sections (n=10) i.e., maxillary right- posterior, A; maxillary anterior, B; maxillary left-posterior, C; mandibular right-posterior, D; mandibular anterior, E; mandibular left-posterior, F. Participants visited the hospital seven times: preoperatively, 1V; implant surgery, 2V; stitch removal, 3V; 1-month follow-up, 4V; 2-months follow-up, 5V; before final-restoration delivery, 6V; and after final-restoration delivery, 7V. The implant stability was evaluated with the Osstell Mentor (ISQ), Periotest M (PTV), and Anycheck (IST). The mean values of ISQ, PTV, and IST were analyzed (α=.05). ISQ, PTV, and IST results of 5V and 6V were significantly higher than those of 2V (P<.05). The lowest ISQ results occurred in E location at 5V and 6V (P<.05). In all mandibular locations, IST results of 7V were significantly higher than those of 2V, 3V, 4V, and 5V (P<.05). ISQ results were negatively correlated with PTV and positively correlated with IST, and PTV was negatively correlated with IST. By considering various factors that affect implant stability, the appropriate implant load application time was determined. This could help increase the implant success rate in elderly patients. And as a diagnostic device for implant stability for evaluation of osseointegration in elderly patients, Anycheck was also able to prove its relative reliability compared to Osstell ISQ Mentor and Periotest M.

The impact of the agriculture net carbon effect is crucial for climate change mitigation, yet research on this topic in China is currently insufficient. In this study, the carbon balance ratio (CBR) is used to characterise the net carbon effect of agriculture, and the spatial Durbin model and threshold regression model were used to empirically analyse the CBR with a sample of 30 provincial-level regions in China from 2004 to 2019. The aim was to investigate the mechanism of the influence of the land management scale (SCALE) of farming on the CBR. The results of the study indicate that national farming generally has a net sink effect, with large changes in interannual fluctuations; the expansion of SCALE has an obvious role in increasing sinks and reducing emissions, and has a positive spatial spillover effect on CBR, with significant spatial heterogeneity. Furthermore, as the SCALE expands, the direction of the influence of rural residents’ income and education level on CBR changes in the opposite direction, showing a significant non-linear relationship characteristic. However, in most areas, the SCALE threshold has not yet been reached, suggesting that the improvement in education levels can still offset the negative impact of economic income growth in the short term. The study recommends paying attention to the role of farmers’ human capital, changing production methods, and implementing carbon peaking and carbon neutrality goals to enhance the net sink effect of the farming industry, which would be achieved by increasing land management scale.

The electronic structural evolution of LLM-105 crystal and the (101) plane of LLM-105 crystal under different pressures is investigated by the density functional theory (DFT) calculations and the surface properties of seven low-Miller-index planes of LLM-105 crystal were investigated in this study. The result demonstrates that the surface energy of (101) plane of LLM-105 is much smaller when compared with other low-Miller-index planes of LLM-105.In order to further investigate the stability of crystal structure and (101) plane of LLM-105 under different pressures, a series of pressures ranged from 0 GPa to 55 GPa were applied during the DFT calculation, and the result shows that the electronic structures of LLM-105 crystal and the (101) plane changed with the increase of external pressure and the evolution process of (101) plane is different from that of LLM-105 crystal structure.

Organic light-emitting diodes (OLEDs) are energy-efficient; however, the coordinating ligand can affect their stability. Sky-blue phosphorescent Pt(II) complexes with a C^N chelate, fluorinated-dbi (dbi = [1-(2,4-diisopropyldibenzo[b,d]furan-3-yl)-2-phenyl-1H-imidazole]), and acetylactonate (acac)(1)/picolinate (pic)(2) ancillary ligands were synthesized. The molecular structures were characterized using various spectroscopic methods. The Pt(II) coordination sphere in 2 exhibited a distorted square-planar geometry, with several intra- and inter-molecular interactions involving Cπ⋯H/Cπ⋯Cπ stacking. Complex 1 emitted bright sky-blue light (λmax = 485 nm) with a moderate photoluminescent quantum efficiency of 0.37 and short decay time (6.1 µs) compared to those of 2. Time-dependent density functional theory calculations suggested that the electronic transition of 1 arose from ligand(C^N)-centered π–π* transitions combined with metal-to-ligand charge transfer transitions (MLCT), whereas that of 2 arose from MLCT and ligand(C^N)-to-ligand(pic) charge transfer (LLCT), with minimal contribution from the C^N chelate to the lowest unoccupied molecular orbital. Multi-layered phosphorescent OLEDs using 1 as a dopant and a mixed host, 3,3-di(9H-carbazol-9-yl)-1,1-biphenyl:3-di(9H-carbazol-9-yl)-1,1-biphenyl (mCBP)/9-(3’-carbazol-9-yl-5-cyano-biphenyl-3-yl)-9H-carbazole-3-carbonitrile (CNmCBPCN) were successfully fabricated. At a 10% doping of 1, a current efficiency of 13.6 cd A−1 and external quantum efficiency of 8.4 % at 100 cd m−2 were achieved. These results show that the ancillary ligand in phosphorescent Pt(II) complexes must be considered.

The stepwise hydrogenation of the C=C bond and C=O group of acrolein on Au₃ and Au₅ model systems is investigated using the density functional theory(DFT) PW91 functional. Our results show that the C=C hydrogenation is more favorable than that of C=O bond on Au₃ with the barriers of the rate-determining step being 0.35 and 0.62 eV respectively. On the other hand, the C=O reduction is preferred over the hydrogenation of the C=C bond on Au₅. The corresponding barriers of the rate-determining steps are 0.45 and 0.54 eV, respectively. This demonstrated that the second hydrogenation step controls the reaction on both Au₃ and Au₅ for C=O and C=C hydrogenation and the C=O hydrogenation on Au₅ is preferred over the hydrogenation of the C=C bond, which is helpful to address the reactivity of small size-selected supported gold clusters.

For efficient electrode development in an electrolysis system, Fe₂O₃, MnO, and heterojunction Fe₂O₃-MnO materials were synthesized via a simple sol-gel method. These particles were coated on a Ni-foam electrode, and the resulting material was used as an electrode to be used during an oxygen evolution reaction (OER). A 1000-cycle OER test in a KOH alkaline electrolyte indicated that the heterojunction Fe₂O₃-MnO/NF electrode exhibited the most stable and highest OER activity: it exhibited a low overvoltage (n) of 370 mV and a small Tafel slope of 66 mV/dec. X-ray photoelectron spectroscopy indicated that the excellent redox performance contributed to the synergy of Mn and Fe, which enhanced the OER performance of the Fe₂O₃-MnO/NF electrode. Furthermore, the effective redox reaction of Mn and Fe indicated that the structure maintained stability even under 1000 repeated OER cycles.

In response to the structural optimization problem of PCB stator coreless disc motors, the orthogonal response surface method was used to optimize the motor structure, determine the basic parameters of the motor preliminarily, and conduct orthogonal experiments on the motor parameters based on the optimization design objectives, The optimization factors were the quantity of magnetic pole of the motor rotor, the ratio of main/auxiliary pole size, the thicknessof the permanent magnet, and the air gap length.The motor torque，the amplitude of magnetic density of the air gap and waveform distortion rateare used as optimization objectives. The motor parameters that make the motor torque reach the maximum, the air gap magnetic density maximum, and the waveform distortion rate minimum. Due to the use of PCB plates instead of motor stator cores in PCB coreless disc motors,The service life of the PCB board during motor operation will be reduced with the temperature rise generated by the stator winding To solve this problem, the response surface analysis of the motor is carried out to reduce the temperature rise of the stator windings during the operation of the motor. PCB board and stator winding are the main factors affecting the temperature rise of the motor.Taking the thickness of the PCB board, the hole diameter on the board, and the uneven width of the stator winding as optimization factors, the motor parameters with the lowest temperature rise of the motor winding are obtained. Simulation analysis is conducted using Ansys/Maxwell software, and the results prove the feasibility of optimization.

Sweet sorghum is an important bioenergy grass and valuable forage with a strong adaptability to saline environments. However, little is known about the mechanisms of sweet sorghum coping with ion toxicity under salt stresses. Here, we first evaluated the salt tolerance of a sweet sorghum cultivar “Lvjuren” and determined its ion accumulation traits under NaCl treatments; then explored key genes involved in Na+, Cl−, K+ and NO3− transport using transcriptome profiling and qRT-PCR method. The results showed that the growth and photosynthesis of sweet sorghum were unaffected by 50 and 100 mM NaCl treatments, indicative of a strong tolerance of this species to salt stresses. Under NaCl treatments, sweet sorghum could efficiently exclude Na+ from shoots and accumulate Cl− in leaf sheaths to avoid their overaccumulation in leaf blades; meanwhile, it possessed a prominent ability to sustain NO3− homeostasis in leaf blades. Transcriptome profiling identified several differentially expressed genes associated with Na+, Cl−, K+ and NO3− transport in roots, leaf sheaths and leaf blades of sweet sorghum after 200 mM NaCl treatment for 6 and 48 h. Moreover, transcriptome data and qRT-PCR results indicated that HKT1;5, CLCc and NPF7.3-1 should be key genes involved in Na+ retention in roots, Cl− accumulation in leaf sheaths and maintenance of NO3− homeostasis in leaf blades, respectively. Many TFs were also identified after NaCl treatment, which should play important regulatory roles in salt tolerance of sweet sorghum. This work lays a preliminary foundation for clarifying the molecular basis underlying the adaptation of sweet sorghum to adverse environments.

This paper proposes two max-pooling engines, named the RTB-MAXP engine and the CMB-MAXP engine, with a scalable window size parameter for FPGA-based convolutional neural network (CNN) implementation. The max-pooling operation for the CNN can be decomposed into two stages, i.e., a horizontal axis max-pooling operation and a vertical axis max-pooling operation. These two one-dimensional max-pooling operations are performed by tracking the rank of the values within the window in the RTB-MAXP engine and cascading the maximum operations of the values in CMB-MAXP engine. Both the RBM-MAXP engine and the CMB-MAXP engine were implemented using VHSIC Hardware Description Language (VHDL) and verified by simulations. They have been employed for and tested in our CNN accelerator targeting at the CNN model YOLOv4-CSP-S-Leaky for object detection.

In South Korea, in line with the increasing need for a reliable water supply following the continuous increase in water demand, the Smart Water Grid Research Group (SWGRG) was officially launched in 2012. With the vision of providing water welfare at a national level, SWGRG incorporated information and communications technology in its water resource management, aiming at the development of core technologies for a Smart Water Grid consisting of intelligent microgrids and a demonstration and tests of the developed technologies through a field operation in a living lab. The living lab was built in Block 112 of YeongJong Island, Incheon, South Korea (area of 17.4 km2, population of 8,000), where Incheon International Airport, a hub of Northeast Asia, is located. In this location, water is supplied through a single submarine pipeline, making the place optimal for responses to water crises and the construction of a water supply system during emergencies. From 2017 to 2019, ultrasonic wave type smart water meters and IEEE 802.15.4g advanced metering infrastructure (AMI) networks were installed at 527 sites of 958 consumer areas in the living lab, and core element technologies (intelligent water source management and distribution system, smart water distribution network planning/control/operation strategy establishment, AMI network and device development, integrated management of bi-directional smart water information), and operation solutions (smart water statistics information, real-time demand-supply analysis, decision support system, real-time hydraulic pipeline network analysis, smart DB management, and water information mobile application) were developed through a field operation and testing.

Developing high performance HVAC system using natural refrigerants including carbon dioxide (CO₂) has been important in respect of environmental preservation and associated technologies. Thus studies to optimize the HVAC (heating ventilation air conditioner) system using natural refrigerants through clarifying the cycle performance characteristics are necessary. The CO₂ heat pump system using air and water sources was consisted to examine its performance characteristics, and by varying conditions of several factors that affect or characterize the system performance like the amount of refrigerant charge, EEV (electronic expansion valve) opening, and internal heat exchanger under cooling mode. The performance characteristics of CO₂ heat pump system were tested by using an air enthalpy calorimeter. In the case of the CO₂ heat pump system without internal heat exchanger, the opening of #3 EEV and #4 EEV was 60% and refrigerant charge amount was 5,600g. However, in the case of that with internal heat exchanger, the best performance was obtained when the opening of #2 EEV is 20%. From the present studies, it was observed that the performance variation and operational characteristics of the CO₂ heat pump system were affected by design factors like refrigerant charge amount, EEV opening, and internal heat exchanger and thereby, the configuration on an optimal operation conditions of the system was enabled.

With the rapid development of MEMS (Micro-electro-mechanical Systems) fabrication technologies, manifolds microelectrodes with various structures and functions have been designed and fabricated for applications in biomedical research, diagnosis and treatment through electrical stimulation and electrophysiological signal recording. The flexible MEMS microelectrodes exhibit multi-aspect excellent characteristics beyond stiff microelectrodes based on silicon or SU-8, which comprising: lighter weight, smaller volume, better conforming to neural tissue and lower fabrication cost. In this paper, we mainly reviewed key technologies on flexible MEMS microelectrodes for neural interface in recent years, including: design and fabrication technology, flexible MEMS microelectrodes with fluidic channels and electrode-tissue interface modification technology for performance improvement. Furthermore, the future directions of flexible MEMS microelectrodes for neural interface were described including transparent and stretchable microelectrodes integrated with multi-aspect functions and next-generation electrode-tissue interface modifications facilitated electrode efficacy and safety during implantation. Finally, the combinations among micro fabrication techniques with biomedical engineering and nanotechnology represented by flexible MEMS microelectrodes for neural interface will open a new gate to human lives and understanding of the world.

In order to better plan new or update sewer pipe condition assessment protocols, this paper presents systematic comparisons of four most widely-used sewer condition assessment protocols, including the fourth edition of Sewer Rehabilitation Manual (SRM-4) in UK, Pipeline Assessment and Certification Program (PACP) in America, Sewer Physical Condition Grading Protocols (SPCCM) in Canada, and Technical Specification for Inspection and Evaluation of Urban Sewer (TSIEUR) in China. In qualitative comparison, the defects, deduct values and assessment methods of the four protocols were analyzed; in quantitative comparison, protocols were used to evaluate the same 182 sewer pipe segments based on field data and the assessment results were compared. It was found that SRM-4 are the most optimistic with 59% pipes being Grade 1 and Grade 2, while SPCCM gives the most pessimistic results with 62% pipes being Grade 3 and Grade 4. Assessment results by PACP and TSIEUR are in the middle. The main reasons for the different evaluation results were due to the different weight of defect and evaluation methods used.

Transient receptor potential melastatin-8 (TRPM8) is a cation channel that is activated by cold and “cooling agents” such as menthol and icilin, which induce a cold sensation. Stimulation of TRPM8 activates an intracellular signaling cascade that ultimately leads to a change in the gene expression pattern of the cells. Here, we investigated the TRPM8-induced signaling pathway that links TRPM8 channel activation to gene transcription. Using a pharmacological approach, we show that inhibition of phosphatidylinositol 4-phosphate 5 kinase alpha (PIP5K), an enzyme essential for the biosynthesis of phosphatidylinositol 4,5-bisphosphate, attenuated TRPM8-induced gene transcription. Analyzing the link between TRPM8 and Gq proteins, we show that pharmacological inhibition of the beta gamma subunits impairs TRPM8 signaling. In addition, genetic studies showed that TRPM8 requires an activated Galpha subunit for signaling. In the nucleus, the TRPM8-induced signaling cascade triggers an activation of the transcription factor AP-1, a complex consisting of a dimer of basic region leucine zipper (bZIP) transcription factors. Here, we identified the bZIP protein c-Jun as an essential component of AP-1 within the TRPM8-induced signling cscade. In summary, with PIP5K, Gq subunits and c-Jun we have identified key molecules in the TRPM8-induced signaling from the plasma membrane to the nucleus.

Effective detection of isopropyl methylfluorophosphonate (GB, sarin), a type of organophosphine poisoning agent, is an urgent issue to be addressed in maintaining public safety. In this research, a gas-sensitive film material defined as poly (4-hydroxy-4,4-bis trifluoromethyl) - butyl-1-enyl) - si-loxane (SXFA) with the structure of hexafluoroisopropyl (HFIP) functional group was synthesized by using methyl vinylpropyl dichlorosilane and hexafluoroacetone trihydrate as initial materials. Synthesis process products were characterized by FTIR. SXFA was prepared on a 200 MHz shear surface wave delay line with spin coating method for GB detected. Detection limit of ＜ 0.1 mg/m3 was obtained through conditional experiments. Meanwhile, we also obtained the maximum re-sponse of 2.168 mV at 0.1 mg/m3 concentration, which indicting a much lower detection limit of SAW-SXFA sensor. Additionally, the maximum response standard deviation of 0.11 mV with a co-efficient of variation of 0.01, as well as the maximum recovery standard deviation of 0.22 mV with a coefficient of variation of 0.02 were also obtained through 5 repeated experiments. Results showed that the SAW-SXFA sensor has strong selectivity and reproducibility, good selectivity, positive detection ability, high sensitivity, and fast alarm performance for sarin detection.

Brucella abortus is a facultative intracellular Gram-negative bacterium that causes chronic persistent infections in humans and livestock. In this study, conventional bio-typing, multiple-locus variable-number tandem repeat analysis (MLVA), and whole-genome sequencing-single-nucleotide polymorphism (WGS-SNP) were used to investigate the molecular epidemiology characteristics of Brucella abortus strains in China and their relationships to world lineages. A total of 100 strains were collected from 1953 to 2013, suggesting that B. abortus circulated in China in the past five decades. Moreover, most strains were mainly distributed in the northwest area. During this period, seven biovars were found, indicating that B. abortus displayed a high diversity of biovars and that the main epidemic areas are in the northern provinces. Strains have high genetic diversity, and bruce07 is the most helpful locus for genotyping of this population. Moreover, 17 MLVA-11 genotypes were found; 13 of them are of known genotypes and four are unassigned genotypes, indicating that B. abortus in this study had several geographic origins. Still, strains from unassigned genotypes may originate from China. Many shared MLVA-16 genotypes were observed in strains from the same provinces in Northern China, which confirmed a brucellosis outbreak within northern regions. WGS-SNP analysis showed that eight Chinese strains formed a ladder-like phylogram (C. Ⅶ) with strains from nine countries, including Uganda, Iraq, Russia, Georgia, Spain, Italy, Egypt, Mongolia, and China; strains were introduced to these countries from a single source. Notably, Chinese strains were closely related to strains from Russia and Mongolia; frequent animal (cattle) trade and exchanges may promote this process. We will provide new and insightful information for strength surveillance and control of B. abortus brucellosis in China.

Heavy metals, including arsenic from abandoned mines, are easily transported with sediment and deposited in water bodies such as reservoirs and lakes, creating critical water quality issues when they are released. Understanding the leaching of heavy metals is necessary for developing efficient water quality improvement plans. This study investigated how arsenic leaches from different soil types and responds to hydrologic conditions to identify areas susceptible to arsenic contamination. In this study, batch- and column-leaching tests and sequential extraction procedures were used to examine arsenic leaching processes in detail. The results showed that most arsenic-loaded sediments accumulated in the vicinity of a reservoir inlet, and arsenic in reservoir beds have a higher leaching potential than those from agricultural land and river beds. Arsenic deposited at the bottom of reservoirs had higher mobility than that in the other soils, and arsenic leaching was closely associated with the acidity of water. In addition, arsenic leaching was found to be responsive to seasons (wet or dry) as its mobilization is controlled by organic compounds that vary over time. The results suggested that temporal variations in the hydrochemical composition of reservoir water should be considered when defining a management plan for reservoir water quality.

Light trapping in single nanowires (NWs) are of vital importance for photovoltaic applications. However, circular NWs (CNWs) can limit its light-trapping ability due to high geometrical symmetry. In this work, we present a detailed study of light trapping in single NWs with an elliptical cross-section (ENWs). We demonstrate that the ENWs exhibit significantly enhanced light trapping compared with the CNWs, which can be ascribed to the symmetry-broken structure that can orthogonalize the direction of light illumination and the leaky mode resonances (LMRs). That is, the elliptical cross-section can simultaneously increase the light path length by increasing the vertical axis and reshape the LMR modes by decreasing the horizontal axis. We found that the light absorption can be engineered via tuning the horizontal and vertical axes, the photocurrent is significantly enhanced by 374.0% (150.3%, 74.1%) or 146.1% (61.0%, 35.3%) in comparison with that of the CNWs with the same diameter as the horizontal axis of 100 (200, 400) nm or the vertical axis of 1000 nm, respectively. This work advances our understanding of how to improve light trapping based on the symmetry breaking from the CNWs to ENWs and provides a rational way for designing high-efficiency single or self-assembled NW photovoltaic devices.

To improve carbon efficiency for urban logistics service system composed of a third-party logistics service provider (3PLs) and an e-business enterprise, low-carbon operation game between them was studied. Considering low carbon technology investment cost and sales expansion effect of low carbon level, profit functions for both players were constituted. Based on their different bargaining capabilities, totally 5 types of game scenarios were designed. Through analytical solution, Nash Equilibria under varied scenarios were obtained. By analyzing these equilibria, 4 major propositions were given, in which, some key variables and system performance index were compared. Results show that the best system yields could only be achieved under the fully cooperative situation; limited cooperation only for carbon emission reduction would not benefit the system performance improvement; E-business enterprise-leading game’s performance overtook 3PLs-leading ones.

It is crucial to forecast the water demand accurately for supplying water efficiently and stably in a water supply system. In particular, accurately forecasting short-term water demand helps in saving energy and reducing operating costs. With the introduction of the Smart Water Grid (SWG) in a water supply system, the amount of water consumption is obtained in real time through an advanced metering infrastructure (AMI) sensor, which can be used for forecasting the short-term water demand. The models widely used for water demand forecasting include the autoregressive integrated moving average, radial basis function-artificial neural network, quantitative multi-model predictor plus, and long short-term memory. However, there is a lack of research on assessing the performance of models and forecasting the short-term water demand by applying the data on the amount of water consumption by purpose and the pipe diameter of an end-use level of the SWG demonstration plant in each demand forecasting model. Therefore, in this study, the short-term water demand was forecasted for each model using the data collected from the AMI, and the performance of each model was assessed. The Smart Water Grid Research Group installed ultrasonic-wave-type AMI sensors in the block 112 located in YeongJong Island, Incheon, and the actual data used for operating the SWG demonstration plant were adopted. The performance of the model was assessed by using the residual, root mean square error (RMSE), normalized root mean square error (NRMSE), Nash–Sutcliffe efficiency (NSE), and Pearson correlation coefficient (PCC) as indices. The water demand forecast was slightly underestimated in models that employed the assessment results based on the RMSE and NRMSE. Furthermore, the forecasting accuracy was low for the NSE due to a large number of negative values; the correlation between the observed and forecasted values of the PCC was not high, and it was difficult to forecast the peak amount of water consumption. Therefore, as the short-term water demand forecasting models using only time and the amount of water consumption have limitations in reflecting the characteristics of consumers, a water supply system can be managed more precisely if other factors (weather, customer behavior, etc.) influencing the water demand are applied.

System-of-systems (SoS) evolution is a complex and unpredictable process. Although various principles to facilitate collaborative SoS evolution have been proposed, there is a lack of experimental data validating their effectiveness. To address these issues, we present an Agent-Based Model (ABM) for SoS evolution in the Internet of Vehicles (IoV) , serving as a quantitative analysis tool for SoS research. By integrating multiple complex and rational behaviors of individuals, we aim to simulate real-world scenarios as accurately as possible. To simulate the SoS evolution process, our model employs multiple agents with autonomous interactions and incorporates external environmental variables. Furthermore, we propose three evaluation metrics: evolutionary time, degree of variation, and evolutionary cost, to assess the performance of SoS evolution. Our study demonstrates that enhanced information transparency significantly improves the evolutionary performance of distributed SoS. Conversely, the adoption of uniform standards only brings limited performance enhancement to distributed SoSs. Although our proposed model has limitations, it stands out from other approaches that utilize Agent-Based Modeling to analyze SoS theories. Our model focuses on realistic problem contexts and simulates realistic interaction behaviors. This study enhances the comprehension of SoS evolution processes and provides valuable insights for the formulation of effective evolutionary strategies.

The purpose of this paper is to propose a novel transfer learning regularization method based on knowledge distillation. Recently, transfer learning methods have been used in various fields. However, the problems such as knowledge loss still occur during the process of transfer learning to a new target dataset. To solve these problems, there are various regularization methods based on knowledge distillation techniques. In this paper, we propose a transfer learning regularization method based on feature map alignment used in the field of knowledge distillation. The proposed method is composed of two attention based submodules: self-pixel attention (SPA) and global channel attention (GCA). The self-pixel attention submodule utilizes both the feature maps of the source and target models, so that it provides an opportunity to jointly consider the features of the target and the knowledge of the source. The global channel attention submodule determines the importance of channels through all layers, unlike the existing methods that calculate these only within a single layer. Accordingly, transfer learning regularization is performed by considering both the internal of each single layer and the depth of the entire layer. Consequently, the proposed method using both of these submodules showed overall improved classification accuracy than the existing methods in classification experiments on commonly used dataset.

We investigated the effect of C. psittaci and H9N2 coinfection on HD11 cells in vitro, expecting to find the potential pathogenesis of airsacculitis caused by co-infection of C. psittaci and H9N2. HD11 cells were infected with C. psittaci and/or H9N2 in a different order, and effects of the co-infection on iNOS expression and activity, NO synthesis, cell phagocytosis, and cytokines levels in HD11 cells were determined. Results showed that C. psittaci and H9N2 can significantly aggravate the mortality of HD11 cells compared to the effects of infection with one pathogen alone. In addition, infection with C. psittaci can increase the replication of H9N2 in HD11 cells, whereas decrease the iNOS level and enzyme activity as well as NO concentration of HD11 cells by H9N2 infection. We also found that C. psittaci infection alone can significantly decrease the phagocytosis of HD11 cells, compared to H9N2 infection alone. Furthermore, infection with C. psittaci can increase the mRNA expressions of type Th2 cytokines IL-6 and IL-10 of HD11 cells by H9N2 infection. All the above data indicated that primary C. psittaci infection is able to aggravate H9N2 invasion by down-regulating functions of HD11 cells

.Purpose: This paper presents a comparative analysis of state-of-the-art DIR algorithms in the context of head and neck squamous cell carcinoma (HNSCC) radiation therapy. Materials and Methods: We used a dataset of head and neck cancer patients within the Cancer Image Archive, which includes 31 patients with 3D CT image data from pre-treatment, mid-treatment, and post-treatment stages of radiotherapy. We applied DIR algorithms to two datasets, one for pre-treatment to mid-treatment registration and another for mid-treatment to post-treatment registration, by aligning one CT image to another CT image. To quantitatively analyze the patient data, we focused on the spinal cord, optic nerve, brain stem, cochlea, and PTV as the OAR datasets. To verify the DIR algorithm, we used two non-learning-based methods, SyN and NiftyReg, as well as three deep learning-based methods, Voxelmorph, Cyclemorph, and Transmorph. We trained a deep learning model by adjusting the ratio of the training dataset, validation dataset, and test dataset to 7:1:2. Results: The average DSCs of SyN and NiftyReg, the non-learning-based methods, were 0.74±0.06 and 0.70±0.12, respectively. The deep learning-based methods, Voxelmorph, Cyclemorph, and Transmorph, had average DSCs of 0.72±0.08, 0.68±0.11, and 0.69±0.13, respectively. The deep learning DIR algorithm produced transformed outputs of OAR/PTV in a shorter time than other models, including commercial and conventional mathematical algorithms (At Inference(sec/images), Voxelmorph: 0.36, Cyclemorph: 0.3, Transmorph: 5.1, SyN: 140, NiftyReg: 40.2). Conclusions: In conclusion, our study provides a comprehensive comparison of commercial DIR algorithms with traditional and deep learning-based DIR methods. Our results demonstrate that commercial DIR algorithms outperform traditional DIR methods in terms of accuracy and efficiency. However, we also show that deep learning-based DIR methods have the potential to achieve similar performance to commercial algorithms with proper training and optimization. Our findings suggest that both commercial and deep learning-based DIR methods have their respective advantages and limitations, and the choice of method should depend on the specific requirements of the clinical application. Overall, our study contributes to ongoing efforts to improve the accuracy and efficiency of DIR methods for better patient outcomes.

This study was conducted to improve the white index (WI) by preparing thermally expandable microspheres (TEMs) for wallpaper. The thermal properties, foam expansion ratio and WI were studied depending on the particle size of colloidal silica in the preparation of TEMs. As a result, the TEMs with small particles of colloidal silica showed the best results for whiteness and yellowing. Additionally, TGA results indicated that it was highly possible that colloidal silica with small particle sizes was physically or chemically attached to the surface of the TEMs that led to an improvement in whiteness at high temperatures.

Surface area and pore size distribution of Eucalyptus samples pretreated by different methods were determined by the Brunauer-Emmett-Teller (BET) technique. Three methods were applied to prepare cellulosic biomass samples for BET measurements: air, freeze, and critical point drying (CPD). Air and freeze drying caused severe collapse of biomass pore structures, but CPD effectively preserved biomass morphology. Surface area of CPD prepared Eucalyptus samples was determined to be 58–161 m2/g, whereas air and freeze dried samples were 0.5–1.3 and 1.0–2.4 m2/g, respectively. Average pore diameter of CPD prepared Eucalyptus samples were 61–70Å. CPD preserved Eucalyptus sample morphology by replacing water with a non-polar solvent, CO2 fluid, which prevented hydrogen bond reformation in the cellulose.

Aim: To improve risk stratification in early-stage endometrial cancer (EC), we performed mo-lecular classification, and L1CAM immunohistochemistry (IHC) for additional risk assessment. Method: We analyzed archival tumor tissue from 247 early-stage EC patients. POLE mutations were detected using a Droplet digital polymerase chain reaction assay and Sanger sequencing, while the mismatch repair (MMR) status was determined by MMR protein IHC and MSI test. Additionally, we conducted IHC of p53 and L1CAM. Results: The 247 ECs were categorized into four subgroups: POLE-mutated (13.0%), MMR-deficient (27.9%), p53-abnormal (8.5%), and non-specific molecular profile (NSMP, 50.6%). We further subcategorized NSMP subgroup into NSMP-L1CAMneg (44.9%) and NSMP-L1CAMpos (5.7%), which we refer to as the molecu-lar-L1CAM classification. The molecular-L1CAM classification was an independent prognostic factor for recurrence-free survival (RFS) and overall survival (OS) (p <0.001, each). Similarly, the simplified L1CAM-p53 categorization, for practical use, remained an independent prognostic factor for RFS and OS (p <0.001, p =0.003, respectively). Conclusion: Integrating the molecu-lar-L1CAM classification or the simplified L1CAM/p53 categorization can enhance risk stratifi-cation in early-stage EC, providing valuable prognostic information to guide treatment deci-sions and improve patient outcomes.

As climate changes, our daily life has been much influenced by abnormal meteorological phenomena such as heavy rainfall, heat wave, heavy snowfall, and fine dust. Atmospheric air quality is worsening day by day and indoor air quality is also affected by interconnected daily activities throughout the inside and outside of buildings and houses. Nowadays, pollutants from various sources are emitted, transformed by sunlight, vapor, and ozone and transported into the city from country to country. Due to these reasons, there have been high demands to monitor the transportation of particulate matters and improve air quality. Monitoring of pollutants and identification of type and its concentration enables us to track and control its generation and consequently find out the solution. However, monitoring of pollutants, especially, particulate matter generation and its transportation is still not fully operated in atmospheric air due to its open nature and meteorological factors. Even though indoor air is relatively easy to monitor and control than outdoor in the aspect of specific volume and contaminant source, but it still needs to consider the meteorological parameters because indoor air is not fully separated from the outdoor air flow and contaminants transportation. In this study, optical approach using spectral sensor was attempted to reveal the feasibility of wavelength and chromaticity values of reflected light from specific particles. From the analysis of reflected light of various particulate matters according to different liquid additives, parameter studies were performed to investigate which experimental conditions can contribute to the enhanced selective sensing of particulate matters. Five different particulate matters such as household dust, soil, talc powder, gypsum powder and yellow pine tree pollen were utilized and observed to elucidate the relationship between property of particulate matter and detected light spectrum. Applicable approaches to assist current particle matter sensors and improve the selective sensing were suggested.

Water pollution, intensified by the release of hard-to-degrade pollutants, poses severe threats to ecosystems, human health, and economic development. The existing advanced oxidation processes often involve high operational costs and may result in secondary pollution, highlighting the necessity for innovative and more sustainable solutions. To address these challenges, our study introduces a cost-effective and eco-friendly corona discharge barrier plasma discharger for wastewater treatment. Through the central composite design/response surface methodology, a high decolorization rate of 98% of methylene blue (MB) within 10 minutes was achieved by optimizing parameters such as pH and voltage. Furthermore, the mechanisms of the generation of reactive oxygen species via this device was discussed in detail and the degradation pathways of MB were described. Moreover, this device is also very energy-efficient, with a low energy density and electrical energy per order of 0.15 watt/mL and 5.79 kWh/m³/order, respectively. In conclusion, the plasma discharger developed in this study provides a cost-effective and environmentally sustainable solution for dye wastewater treatment. This research contributes significantly to the advancement of sustainable dye wastewater management practices, offering an innovative method that meets both environmental and economic objectives.

Recently, cobalt iron boron (CoFeB) thin films have been widely investigated to apply to magnetic sensors, due to their high magnetic moment, anisotropy, and stability. However, most of these studies are conducted on rigid silicon substrates. For more diverse applications of magnetic sensors and angle sensors, it is important to explore the properties of ferromagnetic thin films grown on non-rigid deformable substrates. Here, using representative deformable substrates such as polyimide (PI), polyethylene naphthalate (PEN) and polydimethylsiloxane (PDMS) that can be bent or stretched, we report experimental comparison of in-plane magnetic field angle-dependent properties of the amorphous Ta/CoFeB/MgO/Ta thin film which is grown on those deformable substrates. We investigate effects of substrate roughness, tensile stress, characteristics of deformable substrates, and sputtering process on the change of magnetic properties like coercive field (Hc), remanence over saturation magnetization (Mr/Ms), and their biaxial characteristics. This work presents unconventional foundations for exploring deformable magnetic sensors capable of detecting magnetic field angle.

Saikosaponin (SS) a is a compound with various pharmacological properties and easily degraded into SSb1 and SSg in acid condition. In present work another two new degradation products of SSa formed under acid hydrolytic condition were detected and isolated by analytical and semi-preparative liquid chromatography technology, furthermore their structures were characterized as hydroxyl-saikosaponin a and SSb2 by spectral analysis, which is not only essential in stability-indicating method development and validation but also could be used as a worst case to assess the analytical method performance of SSa. Moreover their structural transformation pathways were also proposed.

The agamid lizard Phrynocephalus melanurus, is restricted to the Northwest China (Dzungar Basin) and adjacent Eastern Kazakhstan (Zaisan and Alakol basins). To elucidate the phylogeography of P. melanurus, we obtained the mitochondrial DNA COI segments of 175 sampled lizards from 44 localities across the whole distribution range. Phylogenetic analyses revealed two main clades comprising six geographically structured lineages (I, IIa, IIb, IIc1, IIc2, and IIc3) that fits an isola-tion by distance (IBD) model. The divergence from the most recent ancestor was dated to ~1.86 million years ago (Ma). Demographic analyses demonstrated lineage-specific response to past climate change: stable population for Clade I, IIb and IIc2; while past population expansion for IIc1 and IIc3 since 0.02 Ma and 0.18 Ma, respectively. Bayesian phylogeographic diffusion anal-yses detected initial spreading at the Saur Mount vicinity approximately 1.8 Ma. Historical species distribution modeling (SDM) projected expansion of the suitable habitat in the last interglacial period and stepwise contraction in the Last Glacial Maximum and Holocene epochs. The SDM predicts a shrinkage and shift of suitable area eastward as a response to future climate change. Our findings suggest that the evolution of P. melanurus followed a parapatric divergence with subsequent dispersal and adaptation to cold and dry environments during the Quaternary. Moreover, future conservation strategies need to be taken to maintain the population of lineage IIc1.

Although there are a large number of databases available for regulatory elements, bottleneck has been created by the lack of bioinformatics tools for predicting types of mechanisms underlying actions of regulatory elements. To reduce the gap, we developed ARabidopsis Transcription regulatory Factor Domain-domain interaction Analysis Tool- Liquid-liquid phase separation (LLPS), Oligomerization, GO analysis (ART FounDATion-LOG), a useful toolkit for protein-nucleic acid interactions (PNI) and protein-protein interactions (PPI) analysis based on domain-domain interaction (DDI). LLPS, protein oligomerization, structural properties of protein domains, and protein modifications are major components in orchestrating spatio-temporal dynamics of PPI and PNI. Our goal is to integrate PPI/PNI information into development of prediction model for identifying important genetic variants in peach. The program unified inter-database relational keys by protein domains for facilitating inference from the model species. Key advantage of the program lies in the integrated information of related features: LOG, structural characterization of domain (e.g. domain linker, intrinsically disordered regions, DDI, domain-motif (peptide) interaction, beta-sheet and transmembrane helices), and post-translational modification. We provided simple tests to demonstrate how to use the program. The program may be applied to other eukaryotic organisms. The program codes and data are freely available for download at and https://sourceforge.net/projects/artfoundation-log/.

Ecological connectivity, as a research method related to spatial ecology and conservation biology, has attracted increasing attention from researchers at home and abroad in recent years. Habitat connectivity, as a key link in ecological connectivity, is of great significance to promote offshore ecological restoration and protection. However, there has been less systematic research about habitat connectivity, which lacks corresponding theories and practices. Therefore, this paper discusses habitat connectivity from three aspects: (1) the concept of habitat connectivity is introduced and clarified, (2) the application of connectivity in artificial habitat and adjacent waters and its relationship with biodiversity conservation are reviewed and illustrated with examples, and (3) the future development trends of this research direction are summarized and prospected, in order to provide a scientific basis and useful reference for the related work of offshore restoration projects in China. Generally, this paper argues that an increase in human behavior irreversibly destroys the connectivity of marine habitats and threatens the temporal scales of biodiversity and ecosystem services. Therefore, the theoretical research results and practical experience of ecological connectivity should be fully applied to marine ecosystems, and the restoration of degraded ecosystems should be encouraged and supported in ways that promote natural recovery.

The emergence of diverse infections worldwide, which is a serious global threat to human existence, necessitate the urgent development of novel therapeutic candidates that can combat these diseases with efficacy. Isatin, a secondary metabolite from tryptophan is considered a privileged scaffold and favorable pharmacophore with a unique structural moiety and varied chemical and biological properties resulting in its widespread applications by medicinal chemists. Molecular hybridization is one of the most common and important techniques use in the synthesis of their bioactive hybrids in drug discovery. This review containing published articles from 2005 to 2022 focuses on isatin hybrids which have been synthesized and reported in the literature alongside a discussion on their biological properties. The purpose of this review is to set up the direction for the design and development of isatin-hybrids with tailored biological properties as effective therapeutic candidates inspired by nature.

Ningxiang pig is renowned breed for its exceptional meat quality, but it possesses suboptimal carcass traits. To elucidate the genetic architecture of meat quality and carcass traits in Ningxiang pigs, we assessed heritability and executed a genome-wide association study (GWAS) concerning carcass length, backfat thickness, meat color parameters (L.LD, a.LD, b.LD), and pH at two postmortem intervals (45 minutes and 24 hours) within a Ningxiang pig population. Heritability estimates ranged from moderate to high (0.30 ~ 0.80) for carcass traits and from low to high (0.11 ~ 0.48) for meat quality traits. We identified 21 significant SNPs, the majority of which were situated within previously documented QTL regions. Furthermore, the HMGA1 gene emerged as a pleiotropic gene correlated with carcass length and backfat thickness. The ADGRF1, FKBP5, and PRIM2 genes were associated with carcass length, while the NIPBL gene was linked to backfat thickness. These genes hold potential for use in selective breeding programs targeting carcass traits in Ningxiang pigs.

Recycling waste products is an environmental-friendly activity that can bring benefits to accompany, saving manufacturing costs and improving economic efficiency. For the beer industry, recycling bottles can reduce manufacturing costs and reduce the industry's carbon footprint. This paper presents a model for a multi-objective collection-distribution center location and allocation problem in a closed loop supply chain for the beer industry, in which the objective is to minimize total costs and transportation pollution. Uncertainties in the form of randomness and fuzziness are jointly handled in this paper to ensure a more practical problem solution, for which returned bottle sand unusable bottles are considered fuzzy random variables. A heuristic algorithm based on priority-based global-local-neighbor particle swarm optimization (pb-glnPSO) is applied to ensure reliable solutions for this NP-hard problem. A case study on a beer operation company is conducted to illustrate the application of the proposed model and demonstrate the priority-based global-local-neighbor particle swarm optimization.

Plants significantly shape root-associated microbiota, making rhizosphere microbes useful environmental indicator organisms for safety assessment. Here, we report the pyrosequencing of the bacterial 16S ribosomal RNA in rhizosphere soil samples collected from transgenic cry1Ab/cry1Ac Bt rice Huahui No. 1 (GM crop) and its parental counterpart, Minghui63. We identified a total of 2,579 quantifiable bacterial operational taxonomic units (OTUs). Many treatment-enriched microbial OTUs were identified, including 14 NonGM-enriched OTUs and 10 GM-enriched OTUs. The rhizosphere microbiota communities were influenced more strongly by growth in the field than by rice varieties. Furthermore, Huahui No. 1 transgenic Bt rice had a greater impact on the rhizosphere bacterial communities than Minghui63. Early developmental stages of the transgenic Bt rice had a significant impact on many Bacillaceae communities. While soil chemical properties were not significantly altered by the presence of transgenic Bt rice, we found peak expression level of Bt proteins during the seedling stage, which may be an intriguing factor for bacterial diversity variations. Based on these findings, we conclude that transgenic Bt rice has a significant impact on root-associated bacteria. This information may be leveraged in future environmental safety assessments of transgenic Bt rice varieties.

Plant Factory Transplanter (PFT) is a key component of the plant factory system. Its operation status directly affects the quality and survival rate of planted seedlings, which in turn affects the overall yield and economic efficiency. To monitor the operation status and transplanting quality of a transplanting machine in a timely manner, the primary task is to use a computerized and easy-to-use method to monitor the transplanting units. Inspired by the latest developments in augmented reality and robotics, a DT model-based and data-driven online monitoring method for plant factory transplanting equipment is proposed. First, a data-driven and virtual model approach is combined to construct a multi-domain digital twin of the transplanting equipment. Then, taking the vibration frequency domain signal above the transplanting manipulator and the image features of the transplanting seedling tray as input variables, the evaluation method and configuration method of the PFT digital twin system are proposed. Finally, the effect of the transplanter is evaluated, and the cycle can be repeated to optimize the transplanter to achieve optimal operation parameters. The results show that the digital twin model can effectively use the sensor data to identify the mechanical vibration characteristics and avoid affecting transplanting quality due to mechanical resonance. At a transplanting rate of 3000 plants/h, the transplanting efficiency can be maintained at a high level and the vibration signal of X, Y, Z-axis above the transplanting manipulator is relatively calm. In this case, Combined the optimal threshold method with the traditional Wiener algorithm, the identification rate of healthy potted seedlings can reach 94.3%. Through comprehensively using the optimal threshold method and 3D block matching filtering algorithm for image threshold segmentation and denoising, the recognition rate of healthy seedlings has reached over 96.10%. In addition, the developed digital twin can predict the operational efficiency and optimal timing of the detected transplanter, even if the environmental and sensor data are not included in the training. The proposed digital twin model can be used for damage detection and operational effectiveness assessment of other plant factory equipment structures.

Calcareous sand deposits are widely distributed along the shoreline in ropical and subtropical regions. Microbially induced calcite precipitation treatment (MICP) is a relatively new method to improve the stiffness and strength of the soil. Little is known about the small-strain shear modulus and damping ratio of MICP-treated calcareous sand, which are two crucial parameters for the prediction of the dynamic behavior of soil. A series of resonant column tests are performed to investigate the dynamic performance of MICP-treated calcareous sand, with special attention paid to the influence of treatment duration and confining stress on the stiffness and damping characteristics. The relationship between the initial dynamic shear modulus and unconfined compressive strength is analyzed. Additionally, the empirical equations of the reference shear strain between treatment duration and confining stress are given. The G/G0 of MICP-cemented calcareous sand presents a higher strain sensitivity than that of untreated sand, and its attenuation pattern can be described by Hardin-Drnevich model. The σc has an apparent effect on the degradation characteristics of the dynamic shear modulus of MICP-treated calcareous sand with a low cementation level, however, its effect decreases with the increasing treatment duration. The relationship between the reference shear strain and the treatment duration and confining stress can be described by a power and a linear formula, respectively.

Based on a constant volume combustion chamber, the initial ambient pressure effect on combustion performance and flame propagation of the active and passive pre-chamber ignition systems were studied. Compared with the passive pre-chamber, the active pre-chamber can significantly expand the lean combustion limit, enhance the ignition and combustion performance, and speed up the combustion of the main combustion chamber. At slightly lean combustion conditions, the heat release performance has a positive correlation with the initial ambient pressure. As the premixed λ increases, the heat release performance and the initial ambient pressure begin to become negatively correlated. Ignition delay can be minimized by controlling the excess air coefficient in the pre-chamber close to the stoichiometric ratio. The high ambient pressure in the constant volume chamber greatly reduces the mixture entrainment ability of the jet flame at lean combustion conditions, thereby reducing the combustion speed and peak heat release rate.

To date, various chimeric lysins have been developed as efficacious antibiotics against multidrug-resistant bacteria, but direct comparisons of their antibacterial activities have been difficult due to the preparation of multiple recombinant chimeric lysins. Previously, we reported an E. coli cell-free expression method to screen better chimeric lysins against Staphylococcus aureus, but we still needed to increase the amounts of expressed proteins enough to be able to detect them non-isotopically for quantity comparisons. In this study, we improved the previous cell-free expression system by adding a previously reported artificial T7 terminator and reversing the different nucleotides between the T7 promoter and start codon to those of the T7 phage. The new method increased the expressed amount of chimeric lysins enough for us to detect them using Western blotting. Therefore, the qualitative comparison of activity between different chimeric lysins has become possible via the adjustment of the amount variables between samples without protein purification. We applied it to select more active chimeric lysins derived from our previously reported chimeric lysin (ALS2). Finally, we compared the antibacterial activities of our selected chimeric lysins with reported chimeric lysins (ClyC and ClyO) and lysostaphin, and determined the rank orders of antibacterial activities on different S. aureus strains in our experimental conditions.

Obesity, which is characterized by an excessive accumulation of body fat, is one of the critical factors causing metabolic syndrome. Many studies have been performed to identify appropriate agents to control obesity, but toxicity remains a problem. Herein, we identified that phenylbutyrate (PBA), which has been used to treat urea cycle disorder with very low toxicity for a long time, efficiently inhibited high fat-induced body weight gain in a diet-induced obesity mouse model (DIO model). PBA treatment decreased body fat mass and increased lean composition. Moreover, PBA increased brown adipose tissue (BAT) activity by increasing glucose uptake, thereby improving glucose tolerance and insulin tolerance. Interestingly, PBA could induce the expression of phosphofructokinase (PFKL), a key enzyme in the glycolytic pathway, and knocking down PFKL dramatically repressed the expression level of Ucp1 as well as those of Prdm16, Cidea, Pgc1α, and Pparγ, which are marker genes for BAT activation. These results strongly suggested that PBA could increase energy expenditure by increasing BAT activity via the induction of PFKL. Taken together, PBA could be used as a therapeutic agent for people with obesity to prevent the development of metabolic syndrome.

The transforming growth factor-β (TGF-β), in which overexpression have been associated with various diseases, has become an attractive molecular target for the treatment of cancers. Three series of 3-substituted-4-(quinoxalin-6-yl) pyrazoles 14a–h, 15a–h, 16a–h, 22a, 22b, 22d, 23a, 23b, 23d, 24b, and 24d were synthesized and evaluated for their activin receptor-like kinase 5 (ALK5) and p38α mitogen activated protein (MAP) kinase inhibitory activity in an enzymatic assays. Among these compounds, the most active compound 16f inhibited ALK5 phosphorylation with an IC₅₀ value of 0.28 µM, with 98% inhibition at 10 µM. Compound 16f also had good selectivity index of >35 against p38α MAP kinase, with 9.0-fold more selective than clinical candidate, compound 3 (LY-2157299). Molecular docking study was performed to identify the mechanism of action of the synthesized compounds and their good binding interactions were observed. ADMET prediction of good active compounds showed that these ones possess good pharmacokinetics and drug-likeness behavior.

Gas flaring is commonly used by industrial plants for processing oil and natural gases in the atmosphere, and hence is an important anthropogenic source for various pollutants including CO₂, CO, and aerosols. This study evaluates the feasibility of using satellite data to characterize gas flaring form space by focusing on the Khanty Mansiysk Autonomous Okrug in Russia, a region that is well known for its dominatingly gas flaring activities. Multiple satellite-based thermal anomaly data products at night are inter-compared and analyzed, including MODIS (Moderate Resolution Imaging Spectroradiometer) Terra level-2 Thermal Anomalies product (MOD14), MODIS Aqua level-2 Thermal Anomalies product (MYD14), VIIRS (Visible Infrared Imaging Radiometer Suite) Active Fires Applications Related Product (VAFP), and VIIRS level-2 data based Nightfire product (VNF). The analysis compares and contrasts the efficacy of these sensor products in detecting small, hot sources like flares on the ground in extremely cold environments such as Russia. We found that the VNF algorithm recently launched by NOAA has the unprecedented accuracy and efficiency in characterizing gas flares in the region owing primarily to the use of Shortwave Infrared (SWIR) bands. Reconciliation of VNF’s differences and similarities with other nighttime fire products is also conducted, indicating that MOD14/MYD14 and VAFP data are only effective in detecting those gas flaring pixels that are among the hottest in the region. Validation of VNF product of gas flaring location with Google Earth images are made. It is shown that that VNF’s estimates of gas flaring area (the area of gas flaming) agree well the counterparts from Google images with a linear correlation of 0.91, highlighting its potential use for routinely monitoring emissions of gas flaring from space.

Recently, research on ultra-high-performance concrete (UHPC) with the characteristics of ultra-high strength, high toughness, and high durability has been actively conducted from materials to actual structural applications. However, research on experimental methods that reflect the unique characteristics of UHPC, which are different from those of normal concrete, is insufficient. To solve the difficulties in applying the compressive creep test method for normal concrete to UHPC and to verify the validity of the recently proposed ASTM C 1856 standard test method, this study performed compressive creep tests on UHPC with variables of specimen size, sustained load intensity, fiber length, and strain measuring method. Two types of cylindrical specimens of ϕ100 × 200 mm and ϕ75 × 150 mm were used for a specimen size variable. The sustained load intensities of 10% to 40% based on the specified compressive strength of 150 MPa were applied. Two types of steel fiber lengths of 13 mm and 19.5 mm in the UHPC mix were used as a variable, and three strain measuring methods of the embedded strain gauge method, the attached strain gauge method, and the strain meter with stud measured the change in length of the UHPC specimens. The experimental results showed that the strain meter method using the standard rod had limitations due to the error in the verification process using the standard rod and the observation error of the measurer, and the sustained load intensity is preferable to 15% to 40% of the actual compressive strength. It was found that it is possible to perform a compressive creep test for UHPC using a specimen with a size of ϕ75 mm or more, and the fiber length did not affect the creep behavior of UHPC up to 19.5 mm. As a result of comparing the UHPC creep test results with the creep prediction model, the B3 model was found to most accurately predict the UHPC creep behavior. The creep coefficient pattern of the B3 model was very similar to the measured results, and well reflected the effects of the mixing ratio and compressive strength of UHPC.

With the rapid evolution of SARS-CoV-2, the emergence of new strains is an intriguing question. This paper presents an evolutionary theory to analyze the mutations of the virus and identify the conditions that lead to the generation of new strains. We represent the virus variants using a 4-letter sequence based on amino acid mutations on the spike protein and employ an n-distance algorithm to derive a variant phylogenetic tree. We show that the theoretically-derived tree aligns with experimental data on virus evolution. Additionally, we propose an A-X model, utilizing the set of existing mutation sites (A) and a set of randomly generated sites (X), to calculate the emergence of new strains. Our findings demonstrate that a sufficient number of random iterations can predict the generation of new macro-lineages when the number of sites in X is large enough. These results provide a crucial theoretical basis for understanding the evolution of SARS-CoV-2.

Ehretia laevis Roxb. (Boraginaceae) has been extensively used as a traditional remedy for the treatment of a diverse range of ailments related to the respiratory system, the gastrointestinal tract, the reproductive system, and against several infections. This review critically assesses and documents, for the first time, the fragmented information on E. laevis, including its botanical description, folklore uses, bioactive phytometabolites and pharmacological activities. The goal is to explore this plant therapeutically. Ethnomedicinal surveys reveal that E. laevis has been used by tribal communities in Asian countries for the treatment of various disorders. Quantitative and qualitative phytochemical investigations of E. laevis showed the presence of important phytoconstituents such as pentacyclic triterpenoids, phenolic acids, flavonoids, fatty acids, steroids, alkaloids, aliphatic alcohols, hydrocarbons, amino acids, carbohydrates, vitamins and minerals. Fresh plant parts, crude extracts, fractions and isolated compounds have been reported to exhibit broad spectrum of therapeutic activities viz., antioxidant, antiarthritic, antidiabetic, anti-inflammatory, antiulcer, antidiarrheal, antidysenteric, wound healing and anti-infective activities. E. laevis is shown to be an excellent potential source of drugs for the mitigation of jaundice, asthma, dysentery, ulcers, diarrhea, ringworm, eczema, diabetes, fissure, syphilis, cuts and wounds, inflammation, liver problems, venereal and infectious disorders. Although few investigations authenticated its traditional uses but employed uncharacterized crude extracts of the plant, the major concerns raised are reproducibility of therapeutic efficacy and safety of plant material. The outcomes of limited pharmacological screening and reported bioactive compounds of E. laevis suggest that there is an urgent need for in-depth pharmacological investigations of the plant.

Oligopeptide transporters (OPTs) are a group of membrane localized proteins that have a broad range of substrate transport capabilities and contribute to numerous biological processes. However, limited information has been reported on OPTs in higher plants. In this study, a comprehensive analysis of the OPT gene family in Medicago truncatula was performed. A total of 26 OPT genes (MtOPT01-MtOPT26) have been identified in the Medicago truncatula genome. Phylogenetic analyses indicated that MtOPTs consisted of two distinct subgroups, 12 MtOPTs belonged to the peptide transport subgroup (PT-OPT) based on their predicted amino acid sequences containing the two highly conserved motifs (NPG and KIPPR) and 14 MtOPTs belonged to yellow stripe subgroup (YS-OPT). The MtOPTs distributed on each of 8 chromosomes in Medicago truncatula. Sequence analysis verified that MtOPTs significant similar to those in other plants. The copy number of MtOPTs was low and the multiply of MtOPTs was simple relatively. Gene structure analysis showed that most of the MtOPTs have various numbers of introns. The multiple of MtOPTs might play different biological roles which were supported by the fact that MtOPTs have a distinct tissue-specific expression pattern. The data obtained in this study will help to better understand the complexity of the MtOPTs gene family and provide new evidence for the function and evolution of the OPT gene family in higher plants.

Antibiotic-loaded bone cements are widely used in orthopedic surgery. However, they present issues such as a short antibiotic release time and the antibiotic resistance. These challenges necessitate the development of novel antibacterial bone cements. Non-leaching bone cement containing antibacterial motifs represents a promising advancement in this direction. Antibacterial motifs are incorporated into the cement either covalently or non-covalently, and while they will not be released, they will still exhibit surface antibacterial activity. This review comprehensively examines the structure and antimicrobial activity of prevalent non-leaching antimicrobial bone cements. Additionally, it delves into the characteristics of current methods employed for detecting surface antimicrobial activity. Finally, the future research direction of non-leaching antibacterial bone cement is discussed, with a specific focus on innovative antibacterial motifs, the mechanisms underlying non-leaching antibacterial properties, and the potential synergies achievable by combining non-leaching antibacterial bone cement with traditional antibiotics.

To ensure consumers can purchase high-quality rice, accurate identification of rice varieties is particularly important. Methods: This article conducts research based on machine learning algorithms from the perspectives of image, spectrum, and spectrogram fusion. Six types of hyperspectral image data of rice were preprocessed using convolutional smoothing (SG) and multiple scatter correction (MSC). Texture information of the images was extracted using gray-level co-occurrence matrix. Spectra, texture, and spectrogram data were fused into a new matrix. Spectral, texture, and spectrogram fusion data were used as inputs for the model, and support vector machines (SVM), logistic regression (LR), and K-nearest neighbors (KNN) classification models were constructed and compared. Results: From the classification results, the spectrogram fusion classification performance was better than classification models using only spectra or texture. Conclusion: The research results showed that the accuracy of SVM and LR classification models exceeded 90%, and the LR model performed the best, effectively classifying rice varieties.

We study the Gaudin models with gl(1|1) symmetry that are twisted by a diagonal matrix and defined on tensor products of polynomial evaluation gl(1|1)[t]-modules, extending all the results of to the twisted case. Namely, we give an explicit description of the algebra of Hamiltonians (Gaudin Hamiltonians) acting on tensor products of polynomial evaluation gl(1|1)[t]-modules and show that there exists a bijection between common eigenvectors (up to proportionality) of the algebra of Hamiltonians and monic divisors of an explicit polynomial written in terms of the highest weights and evaluation parameters. In particular, our result implies that each common eigenspace of the algebra of Hamiltonians has dimension one. We also give dimensions of the generalized eigenspaces.

Resection of malignant lesions in the oral and maxillofacial area causes functional and morphological defects. To recover from these defects, reconstruction surgery is needed such as a primary closure or a flap. There are advantages and disadvantages to the method of using the primary closure and the flap, and the choice of procedure is entirely up to a surgeon. The purpose of this study is to evaluate availability of primary closure in patients. For 10 years from January 2010 to May 2020, patients who recovered using flaps after removing malignant lesions from the oral cavity and those who closed the lesion using primary closure were investigated. The investigation was conducted by searching the database of the hospital. There were 85 patients who removed malignant lesions in the oral and maxillofacial area, and among them 16 patients closed the soft tissue defects using primary closure. Operation time, histologic types, stages, wound status, and period of hospitalization according to the patients' medical records were investigated retrospectively. Between the staging and the primary closure, statistically significant differences were observed between stage I and stage II patients in 13 patients using the primary closure. (P=0.046). Statistically significant differences were identified between operation time and primary closure, with an average of 4.02 hours (P=0.015). The average period of hospitality for patients who underwent primary closure was 13.4 days, compared to 26.7 days for those who underwent flap surgery. This difference was statistically significant (P=0.0003). This study evaluated the use of primary closure in patients who underwent resection of malignant lesions in the oral and maxillofacial area. Although the majority of patients underwent reconstruction with flaps, our results showed that primary closure can be a viable option for certain patients with early-stage lesions. Therefore, oral and maxillofacial surgeons should carefully consider various evaluation criteria and select appropriate reconstruction methods to optimize functional and aesthetic outcomes for each patient.

Background: Breast cancer is a commonly diagnosed cancer worldwide. Human MutT homolog 1 (MTH1) is found to be elevated in breast tumors and cancer cells are addicted to MTH1 for sur-vival. Pharmacological inhibition of MTH1 may be potentially beneficial in the treatment of breast cancer. Methods: MA-24 was screened by malachite green colorimetric assay from MTH1 inhibitors and the kinetic characteristics of MA-24 was assessed. Binding features of MA-24 with MTH1 was as-certained through molecular docking, and cytotoxic activity of MA-24 was validated in vitro and in vivo. Target engagement assays, comet assay and western blot confirmed that the intracellular target and mechanism of MA-24. Results: MA-24 with potent antitumor bioactivity both in vitro and in vivo. MA-24 competitively inhibited the MTH1 and further induce DNA strand breaks, leading to increased apoptosis of cancer cells depending on upregulation of cleaved-caspase 3 – cleaved-PARP axis. Especially, MA-24 exhibited a powerful efficacy and safety in vivo (tumor growth inhibition rate: 61.8%). Conclusions: MA-24 possesses a broad spectrum of breast cancer cytotoxicity and offered valuable insights for overcoming the challenges of chemotherapy-related toxicity, which holds great po-tential for further development MA-24 as an anti-cancer drug.

With the outbreak of coronavirus disease 2019 (COVID-19), there is a need for efficient management of patients with mild or no symptoms, which account for the majority. The aim of this study is to introduce the structure and operation protocol of a living and treatment support centre (LTSC) operated by Seoul National University Hospital in South Korea. The existing accommodation facility was converted into a 'patient centre' where patients was isolated. A few Medical staff here performed medical tests and responded to emergencies. Another part of the LTSC was 'remote monitoring centre'. In this center, patients’ self-measured vital signs and symptoms were monitored twice a day, and the medical staff staying here provided video-consultation via a smartphone. During the 3 weeks from March 5 to March 26, 2020, 113 patients were admitted and treated. LTSC could be an efficient alternative to hospital admission in pandemic situation like COVID-19.

Trueperella pyogenes (T. pyogenes) can cause a variety of infections in animals and lead to economic loss in animal husbandry. TatD DNases are considered to be potential virulence factors in Plasmodium falciparum and Streptococcus pneumoniae. However, the function of TatD DNases in T. pyogenes is still unclear. Therefore, the aim of this study was to illustrate the function of TatD DNases of T. pyogenes (TpTatDs) and investigate whether luteolin is able to inhibit DNase function. The findings of our study are anticipated to be crucial to treating infections caused by T. pyogenes. Bioinformatic analysis has been used for the prediction of crucial functional residues of TpTatDs. The function of TpTatDs was investigated in the presence of divalent cations by hydrolyzing DNA with recombinant TatD proteins. Luteolin is a candidate nuclease inhibitor evaluated in our study. The interactions between luteolin and TpTatDs were tested using molecular docking analysis and surface plasmon resonance (SPR) assays. The inhibitory effect of luteolin on TpTatDs was analyzed by agarose gel electrophoresis. Two genes in the genome of T. pyogenes are suspected to encode TatD DNases. According to the length of their nucleotide sequences, they were named tatD960 and tatD825. Both of the TpTatDs, which are magnesium-dependent, were able to hydrolyze linear DNA and plasmids. In this study, we found through molecular docking analysis and SPR assays that luteolin can stably bind with TpTatDs. The gel assay revealed that luteolin can inhibit the DNase activity of TpTatDs. Our results indicated that TatD DNases from T. pyogenes are Mg2+-dependent DNases and exhibit DNA endonuclease activity. Moreover, luteolin reduced their DNA hydrolysis ability by decreasing the binding between TpTatDs and DNA.

In this paper, the sol−gel method was used to synthesize powders of LaMnO3 (LMO), La0.85Ca0.15MnO3 (LCM), and La0.85Sr0.15MnO3 (LSM). We investigated the impact of substituting Ca and Sr at the A−site on the perovskite crystal structure and electrochemical capabilities of LMO. LCM retained its orthogonal structure in comparison to the parent LMO components, whereas LSM transitioned to a rhombic structure. At 0.5 A/g, the specific capacitance of LCM and LSM electrodes is 185.5 F/g and 248 F/g, respectively.The specific capacitance of LCM was more three times than that of the LMO electrode. Among the three samples (LMO, 22.25 m2 g−1; LSM, 31.56 m2 g−1), the LCM sample exhibited the highest specific surface area of 38.79 m2 g−1. The charge transfer resistances of the LMO, LCM, and LSM are 0.48 Ω, 0.36 Ω, and 0.38 Ω, correspondingly. The LCM electrode exhibits the greatest capacitance performance due to its more refined morphology, increased concentration of oxygen vacancy, and more complete utilization of the perovskite bulk structure. The above results demonstrate that Ca or Sr substitution of A−site compounds has great potential for supercapacitor applications.

A challenge in building large-scale superconducting quantum processors is the precise control and manipulation of the qubit state. However, the crosstalk between the microwave control lines impedes the parallel execution of high-fidelity digital and analog quantum operations. Here, we propose and demonstrate a universal compensation protocol for calibrating the microwave signal crosstalk. We also introduce amplified error sequences to optimize the accuracy. Furthermore, we show a definitive improvement in parallel gate operations with crosstalk cancellation, demonstrating the technique's effectiveness. This work paves the way for superconducting hardware that features automated calibration of microwave crosstalk, leading to enhanced fidelities in multiqubit circuits.

Parasitic diseases continue represent a threat on a global scale, particularly among the poorest countries in the world. This is particularly because of the absence of vaccines, and in some cases, resistance against available drugs, currently being used for their treatment. In this review emphasis is laid on natural products and scaffolds from African medicinal plants (AMPs) for lead drug discovery and possible further development of drugs for the treatment of parasitic diseases. In the discussion, emphasis has been laid on alkaloids, terpenoids, quinones, flavonoids and narrower compound classes of compounds with micromolar range activities against Schistosoma, Trypanosoma and Leishmania species. Suggestions for future drug development from African medicinal plants have also been provided.

Targeted next-generation sequencing (NGS) technology detects specific mutations that can provide treatment opportunities for colorectal cancer (CRC) patients. We included 145 CRC patients who underwent surgery. We analyzed the mutation frequencies of common actionable genes and their association with clinicopathological characteristics and oncologic outcomes using targeted NGS. Approximately 97.9% (142) of patients showed somatic mutations. Frequent mutations were observed in TP53 (70%), KRAS (49%), and APC (47%). TP53 mutations were significantly linked to higher overall stage (p=0.038) and lower disease-free survival (DFS) (p=0.039). ATM mutation was significantly associated with higher tumor stage (p=0.012) and shorter overall survival (OS) (p=0.041). Stage 3 and 4 patients with ATM mutations (p=0.023) had shorter OS, and FBXW7 mutation was significantly associated with shorter DFS (p=0.002). In multivariate Cox regression analysis, ATM mutation was an independent biomarker for poor prognosis of OS (p=0.022). TP53 and FBXW7 mutations are independent biomarkers for poor prognosis of DFS (p=0.042 and 0.030, respectively). A comprehensive analysis of the molecular markers for CRC can provide insights into the mechanisms underlying disease progression and help optimize a personalized therapy.

The goods and services produced by forest and vegetation ecology system is the power by which human society can be promoted fast in high-quality and sustainable way. With the increase of population and economic development in water-limited regions, there is an increasing demand for the quantity and variety of forest vegetation ecosystem products and services. To meet the demands of this situation, most of the original forest has changed into farmland, non-native forest and grass land. As a result, water-plant relationship changed from equilibrium to non-equilibrium, which led to soil drought, soil degradation and vegetation decline in dry years or waste of soil water in rainy years in most of water-limited regions. In order to solve the questions and realize the sustainable utilization of soil water resources and the high quality and sustainable development of social economy, it is necessary to apply the utilization limit theory of soil water resources by plants and the theory of soil water carrying capacity for vegetation to adjust the relationship between plant growth and soil moisture to obtain the maximum yield and benefit of vegetation and serve high-quality and sustainable development.

Ocean surface waves have been utilized as fundamental information in various fields of oceanic research. In this paper, we suggest a simulation and modelling technique for generating an ocean surface wave using an inverse Fast Fourier Transform (iFFT), and we subsequently verify the wave’s accuracy. The conventional method, linear superposition, requires recursive calculation because of the double summation and the time variable; to circumvent this issue, the new algorithm is presented. The Joint North Sea Wave Project (JONSWAP) spectrum is utilized for the ocean surface wave simulation example, and the parameters are the significant wave height (HS) and the zero-crossing wave period (TZ). A coordinate transform for the wavenumber domain was used to apply the inverse FFT algorithm. To verify the accuracy of the simulation result, the relative error between the input condition and the analysis result was calculated. The result for TZ is below 4% relative error, and the maximum relative error for HS is 7%. To avoid the Nyquist frequency for wave-field analysis and simulation, the minimum grid size was calculated by twice applying the maximum wavenumber.

The goods and services produced by forest vegetation ecosystem are the driving force for the rapid, high-quality and sustainable development of human society. In history, with the increase of population and economic development, there is an increasing demand for the quantity and variety of forest vegetation ecosystem products and services in a country or a region. To meet the demands, most of the original forest has become farmland, plantation and grass and crops land. As a result, the plant water relationship changed from equilibrium to non-equilibrium, which easily led to soil drought, soil degradation and vegetation decline in dry years or waste of soil water in rainy years in most of water-limited regions. In order to solve the question and realize the sustainable utilization of soil water resources and the high-quality sustainable development of forest, it is necessary to apply the limit theory of plant utilization of soil water resources and the vegetation carrying capacity theory in the critical period of plant-water relationship regulation to adjust the relationship between plant growth and soil moisture to obtain the maximum yield and benefit and realize high-quality and sustainable development.

Insulated Gate Bipolar Transistor (IGBT) may convey high current and sustain high breakdown voltages; it may provide high power control. In a sense, how IGBT demonstrates the capability of power control was not specifically described, and the equivalent bipolar junction transistors (BJT) activated by an applied bias to the insulated gate is intriguing. As seen in Figure 1, IGBT shows an equivalent circuit structure containing two types of BJT, (NPN-type Bipolar transistor and PNP-type Bipolar transistor), which can be modeled as diode-associated transistor. Apparently, as a bias applies to the controlling gate, the channel beneath the gate oxide gets strongly inversed and turns out to be conductive just like what happens on metal-oxide-silicon field effect transistor (MOSFET), which provides necessary igniting currents to both BJTs and thus causes high current gain flowing through them-selves from the bottom. A proposed and renewed formula provides addressing the above scenario and successfully fitting the measured data that forms the characteristic curves. Some parameters in the proposed formula, which includes size and mobility associated constant, threshold voltage, and Early-Voltage-related lambda for MOSFET, explain and explore the underlying physics. IGBT thus enjoy high input impedance and high current gain due to MOSFET (Insulated Gate) and BJT, respectively. This formula combines both merits of MOSFET and BJT in order to fit the measured data. Indeed, the formula intimately fits IGBT electrical characteristic curves, and thus may be qualified and served as a model. The new model is then advisable for designing power integrated circuit to exactly achieve power saving, power control, and power efficiency.

Urbanization is considered as a main indicator of regional economic development due to its positive effect on promoting industrial development; however, many regions, especially developing countries, are troubled by its negative effect — the aggravating environmental pollution. Many researchers have indicated that rapid urbanization stimulated the expansion of industrial production scale and increased industrial pollutant emissions. However, this judgement contains a grave deficiency in that urbanization not only expands industrial production scales but can also increase industrial labour productivity and change the industrial structure. To modify this deficiency, we first decompose the influence which urbanization impacts on industrial pollutant emissions into the scale effect, the intensive effect and the structure effect by using the Kaya Identity and the LMDI Method; second, we perform an empirical study of the three effects’ impacts by applying the spatial panel model with data from 282 Chinese cities between 2003 and 2013. Our results indicate that (1) there are significant reverse U-shapes between Chinese urbanization rate and its industrial pollutant emissions; (2) the scale effect and the structure effect have aggravated Chinese industrial waste water discharge, sulphur dioxide emissions and soot (dust) emissions, while the intensive effect has generated a decreasing and ameliorative impact on that aggravated trend. The definite relationship between urbanization and industrial pollutant emissions depends on the combined influence of the scale effect, the intensive effect and the structure effect; (3) there are significant spatial autocorrelations of industrial pollutant emissions between Chinese cities, but the spatial spillover effect from other cities does not aggravate local urban industrial pollutant emissions, we offer an explanation to this contradiction that the vast rural areas surrounding Chinese cities have served as sponge belts and have absorbed the spatial spillover of cities’ industrial pollutant emissions. According to the results, we argue that this type of decomposition of the influence into three effects is necessary and meaningful, it establishes a solid foundation for understanding the relationship between urbanization and industrial pollutant emissions, and effectively helps to meet relative policy making.

In this study, we investigate the behavior of randomly moving particles with a defined average energy, focusing on their biased motion around a specific point. These particles' velocity magnitudes follow a Maxwell distribution with a specific scale parameter. Our analysis derives the stochastic rotation rules for these particles and introduces the Ito equation conditions for biased stochastic rotation at a given curl value. We also consider the special relativistic-like effects in this context. The findings are validated through a representative example.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

In a particle swarm with a fixed kinetic energy, the constituent particles move randomly and their velocity magnitudes follow a Maxwell distribution characterized by specific parameters. Within a certain time frame, particles in a sub-swarm may exhibit a bias in their movement direction. Thus, the particles may exhibit a special characteristic (biased random motion), where the group velocity in a particular direction remains constant u. For this biased particle swarm, composed of randomly moving particles with a fixed average speed c, particles have a higher probability of moving in a specific direction. Conversely, their likelihood of moving in all other directions is equally reduced. This study starts from the perspective of biased random walks and using Mathematica software proves that the diffusion rate of particles (in the reference frame R_u observed from R₀) in all directions is slower than that of an unbiased particle swarm with the same average speed c. Specifically, the degree of reduction is determined by the Lorentz-like factor. Lastly, we present the Ito equation for this biased random motion and provide associated verification examples. This study aims to serve as a reference for comprehending the underlying principles of the special relativity effect.

There is a balanced plant-water relationship in the primary vegetation of desert area. With the increase of population and social development in desert areas, people’s need for forest vegetation ecosystem’s goods and service have been changed. To meet the growing demand for plant community goods and services, more original vegetation has been changed into non-native vegetation such as in China loess plateau. However, with the plant growth, sometime soil drying happens and then becomes gradually serious with times in most of desert regions. Serious drying of soil eventually result in soil degradation, vegetation decline and agriculture failure，which influence the produce and supply of forest vegetation goods and service in market in dry year or waste of soil water resources in wet year, which wastes precious nature resources. In order to solve these problems, the soil water resources have to be used in sustainable way and plant-water relationship have to be regulated on Carrying Capacity of Soil Water for Vegetation in the key period of plant water relationship regulation, to carry out sustainable use of nature resources, high-quality and sustainable development of forest and grass or high-quality produce of fruit and crop in desert re-gions.

Studies investigating the acute effect of postprandial exercise (PPE) on glucose responses exhibit significant heterogeneity in terms of participant demographic, exercise protocol, and exercise timing post-meal. As such, this study aimed to further analyze the existing literature on the impact of PPE on glycemic control in individuals with overweight, obesity, and type 2 diabetes (T2D). Literature search was conducted through databases including PubMed, CINAHL, and Google Scholar. Thirty-one original research studies that met the inclusion criteria were selected. The random-effect meta-analysis was performed to compare postprandial glucose area under the curve (AUC) and 24-h mean glucose levels between PPE and the time-matched no-exercise control (CON). Subgroup analysis was conducted to explore whether the glucose-lowering effect of PPE could be influenced by exercise duration, exercise timing post-meal, and disease status of participants. This study revealed significantly reduced glucose AUC (Hedges’ g = -0.317; SE = 0.057; p < 0.05) and 24-hour mean glucose levels (Hedges’ g = -0.328; SE = 0.062; p < 0.05) following PPE than CON. The reduction in glucose AUC was greater (p < 0.05) following PPE lasting >30 min than ≤30 min. The reduction in 24-hour mean glucose levels was also greater (p < 0.05) following PPE initiated ≥60 min than <60 min post-meal and in those with T2D than those without T2D. PPE offers a viable approach for glucose management and can be performed in various forms so long as exercise duration is sufficient. The glucose-lowering effect of PPE may be further enhanced by initiating it after the first hour post-meal. PPE represents a promising strategy, particularly for patients with T2D.

Using the method of the beta function, Sun has recently evaluated some series of the type $\sum_{k=0}^{\infty}(ak+b)x^k/\binom{mk}{nk}$. By factorization of the polynomial $t^{m-n}(1-t)^n-x$, we will give a general method to find new $\pi$-series.

This paper investigates the polarization and heat generation characteristics of batteries under different ambient temperatures and discharge rates by means of using a coupled electric-thermal model. The study found that the largest percentage of polarization is ohmic polarization, followed by concentration polarization and electrochemical polarization. The values of the three types of polarization are generally small and stable under normal-temperature environments and low-discharge rates. However, they increase significantly in low-temperature environments and high-discharge rates and continue to rise during the discharge process. Additionally, ohmic heat generation and polarization generation also increase significantly under these conditions. Reversible entropy heat is less sensitive to ambient temperature but increases significantly with the increase of the discharge rate. Ohmic heat generation and polarization heat generation contribute to the total heat generation of the battery at any ambient temperature, while reversible entropy heat only contributes to the total heat generation of the battery at the end of discharge.

The Korean Pathfinder Lunar Orbiter (KPLO)-MAGnetometer (KMAG) consists of three triaxial fluxgate sensors (MAG1, MAG2, and MAG3) to measure the magnetic field around the Moon. The three sensors are mounted in the order of MAG3, MAG2, and MAG1 inside a 1.2 m long boom away from the satellite body. Before it arrived on the Moon, we compared the magnetic field measurements taken by DSCOVR and KPLO in the solar wind to verify the measurement performance of the KMAG instrument. We found that there were artificial disturbances in the KMAG measurement data, such as step-like and spike-like disturbances, which were produced by the spacecraft body. To remove spacecraft-generated disturbances, we applied a multi-sensor method, employing the gradiometer technique and principal component analysis and using KMAG magnetic field data and confirmed the successful elimination of spacecraft-generated disturbances. This indicates that the multi-sensor method is able to clean the magnetic field data measured onboard the KPLO.

In February 2004, the Food and Drug Administration (FDA) was the first to approve the combination of cisplatin (CDDP) and pemetrexed (PEM) as standard first-line chemotherapy for untreated, unresectable malignant pleural mesothelioma (MPM). However, after that approval, no progress was made in the standard first-line treatment of MPM for almost 15 years. Positive results from a phase 3 study (Mesothelioma Avastin Cisplatin Pemetrexed Study: MAPS) verifying the effect of bevacizumab, an anti-angiogenesis agent added to CDDP/PEM for unresectable MPM, were published in The Lancet in December 2015; however, this did not lead to approval by national drug regulatory agencies. Furthermore, no second-line treatment was established for cases refractory to CDDP/PEM. In August 2018, the Pharmaceuticals and Medical Devices Agency of Japan was the first in the world to approve monotherapy with nivolumab, an immune checkpoint inhibitor (ICI), for previously unresectable, advanced, or recurrent MPM. Following Japan, in October 2020, the FDA approved the combination of nivolumab and ipilimumab for the treatment of previously untreated, unresectable MPM. In this article, we review the transition of drug treatment for MPM, in light of the historical background, focusing on the benefits of ICIs.

Water resources provided by alpine glaciers are an important pillar for people living in the arid regions in the west of China. In this study, the HBV (Hydrologiska Byrans Vattenavdelning) light model was applied to simulate glacier mass balance and runoff in the Koxkar River Basin (KRB) on the south slope of Mt. Tumur, western Tianshan Mts.. Daily temperature and precipitation were calculated by multiple linear regressions and gradient-inverse distance weighting, respectively, based on in-situ observed data by automatic weather stations (AWSs) in the basin (2007–2009) and at four meteorological stations neighbering the basin (1959–2009). Observed daily air temperature and precipitation were taken as input data for the HBV model, which was calibrated using runoff in 2007/08 and 2009/10, and validated in 2008/09 and 2010/11. Generally, the model could simulate runoff very well. The annual glacier mass balance and runoff were calculated using the HBV model driven by interpolated meteorological data for the period of 1959–2009. The simulated glacier mass balance were reasonable when compared with those observed values at nearby glaciers, indicating a decrease trend of mass balance in the basin with an average value of –370.4 mm a^-1 since 1959. The annual runoff showed a slight increase trend (5.51 mm a^-1). Futher analysis indicated that the runoff is more sensitive to temperature than precipitation amuont in the Koxkar river basin.

Acquired Immunodeficiency Syndrome (AIDS) which is chiefly originated by a retrovirus named Human Immunodeficiency Virus (HIV), has influenced about 70 million populations worldwide. Even though several advancements have been invented in the field of antiretroviral combination therapy, still HIV has become the dominant reason for death in South Africa, for example. The current antiretroviral therapies have achieved success in providing instant HIV suppression but with countless undesirable adverse effects. In the present day, the biodiversity of the plant kingdom is being explored by several researchers for the discovery of potent anti-HIV drugs with different mechanisms of action. The primary challenge is to afford a treatment that is free from any sort of risk of drug resistance and serious side effects. Hence, there is a strong demand to evaluate the drugs obtained from natural plants as well as the synthetic derivatives that have been derived from the natural compounds by various chemical reactions. Several plants such as Andrographis paniculata, Dioscorea bulbifera, Aegle marmelos, Wistaria floribunda, Lindera chunii, Xanthoceras sorbifolia and others have displayed significant anti-HIV activity showing more potent anti-HIV activity along with their structures, SARs & important key findings.