Wood-borer extermination by a dry heat clean-up is the essential method from the point of view of sustainability of historical wooden structures like trusses and ceilings in heritage-listed buildings. The wooden components are heated by a hot air of temperature about 100°C until the temperature in the centre of the wooden structures reaches 55°C to kill the wood-borers. In this article we review the method and present solution of the heat equation for structural wooden components. We also suggest an approximate formula that enables to estimate the necessary heating time for different cross sections of wooden components and can be used in technical application of the method.

Tree resin, which in addition to its widespread use in industry is also a macroergic component which has not yet been used for energy purposes. The main goal of this work is to determine the energy content of the resin of spruce, pine and larch and wood components – pulp and turpentine. The combustion heats of resin (MJ/kg) from each timber was determined calorimetrically. The energy values of tree resin (>38.0 MJ.kg-1) were 2.2 and 2.4 times higher than that of bleached and unbleached cellulose, the highest value was recorded for the turpentine (>39.0 MJ.kg-1). The best way of resin tapping is the America method, providing 5 kg resin ha-1 yr-1. The resin quantity tapped was raised at least 3 times applying stimulant, its production cost compared to other feedstocks was the cheapest. The tree resin can be applied as a good means to mitigate global warming and consequently dampen climate change. One tonne of tree resin burned instead of coal spares the atmosphere by 5.0 Mt CO2 since it is environmentally neutral. As resin heating values approach to the lower end of ones of liquid hydrocarbon fuels, greater efforts are needed to examine the most efficient energy use of resin.

The accurate prediction of heat load profiles with a daily resolution is required for a broad range of applications such as potential studies, design, or predictive operation of heating systems. If the heat demand of a consumer is mainly caused by (production) processes independent of the ambient temperature, existing load profile prediction methods fail. To close this gap, this study develops two ex post machine learning models for the prediction of the heat demand with a daily resolution. The selected input features are commonly available to each consumer connected to public natural gas and electricity grids or operating an energy monitoring system: Ambient temperature, weekday, electricity consumption, and heat consumption of the last seven days directly before the predicted day. The study’s database covers electricity and natural gas consumption load profiles from 82 German consumers over a period of two years. Electricity and heat consumption correlate strongly with individual patterns for many consumers. Both, shallow and deep learning algorithms are evaluated. The highest accuracy is achieved by a Long Short Term Memory (LSTM) model with a median of R² of 0.94. The ex post model architecture makes the model suitable for automated anomaly detection in energy monitoring systems.

We conducted this systematic review with the objective to understand the efficacy and safety of proton pump inhibitors [PPIs] in the pediatric population. We have used PubMed to identify randomized controlled trials [RCTs] published between 1st June 2010 and 30th June 2023, in patients from birth to 18 years old, with gastroesophageal reflux disease [GERD], who received treatment with any PPI. The literature yielded 76 articles and 13 met inclusion criteria. For infants, PPIs were equal to placebo in reducing GERD symptoms in 4 articles. In 1, the number of GER episodes and esophageal acid exposure were lower in infants who received PPIs and left lateral position, but there was no significant improvement in symptoms. In another publication, the combination of PPIs and feeding modifications [FM] was not more effective than PPIs alone. For children and adolescents, PPIs were effective in improving symptoms and achieving mucosal and histological healing, which was subsequently maintained. To conclude, PPIs are not effective to reduce symptoms related to GERD in infants, but are effective in older children, along with histological remission. Generally, PPIs are well tolerated, but it is important to not forget the possible adverse events [AE], especially if they are used for a long time.

Atmospheric turbulence characteristics are essential in determining the quality of astronomical images and implementing adaptive optics systems. In this study, the vertical distributions of optical turbulence at the Peak Terskol observatory (43.27472 ° N 42.50083 ° E, 3127 m a.s.l.) using the Era-5 re-analysis and scintillation measurements are investigated. For the closest reanalysis grid node to the observatory, vertical profiles of the structural constant of the air refractive index turbulent fluctuations Cn2 were obtained. The calculated Cn2(z) vertical profiles are compared with the vertical distribution of turbulence intensity obtained from tomographic measurements with Shack-Hartmann sensor. The atmospheric coherence length at the location of Terskol Peak was estimated. Using combination of atmospheric models and scheme paramaterization of turbulence, Cn2(z) profiles at Mt. Kurapdag were obtained. The values of atmospheric coherence length at the Peak Terskol are compared with estimated values of this length at the ten astronomical sites including Ali, Lenghu and Daocheng.

In order to examine the impact of geometric configuration of the human vocal tract on the redistribution of acoustic energy in the frequency spectrum, it is necessary to assemble computation models, which facilitate simple modification of the model’s geometric characteristics. This article describes how the human vocal tract model was constructed using so-called super-elements using the improved reduced system method. The mentioned procedure allows using such a model for demanding optimization calculations, for which the model is modified on the super-element level. Furthermore, the article presents an alternative approach, in which an isoparametric element of a higher degree polynomial was derived. Both approaches were compared and used to find the geometric configuration of the human vocal tract amplifying acoustic energy values on the frequency spectrum to around 3kHz.

Particle acceleration, and the thermalisation of energetic particles, are fundamental processes across the universe. Whilst the Sun is an excellent object to study this phenomenon, since it is the most energetic particle accelerator in the Solar System, this phenomenon arises in many other astrophysical objects, such as active galactic nuclei, black holes, neutron stars, gamma ray bursts, solar and stellar coronae, accretion disks and planetary magnetospheres. Observations in the Extreme Ultraviolet (EUV) are essential for these studies but can only be made from space. Current spectrographs operating in the EUV use an entrance slit and cover the required field of view using a scanning mechanism. This results in a relatively slow image cadence on the order of minutes to capture inherently rapid and transient processes, and/or in the spectrograph slit `missing the action'. The application of image slicers for EUV integral field spectrographs is therefore revolutionary. The development of this technology will enable observations of EUV spectra from an entire 2D field of view in seconds, over two orders of magnitude faster than what is currently possible. The Spectral Imaging of the Solar Atmosphere (SISA) instrument is the first integral field spectrograph proposed for observations at 180A combining the image slicer technology and curved diffraction gratings in a highly efficient and compact layout, while providing important spectroscopic diagnostics for characterization of solar coronal and flare plasmas. SISA's characteristics, main challenges and the on-going activities to enable the image slicer technology for EUV applications are presented in this paper.

Significant efforts are being made across academia and industry to better characterize lithium-ion battery cells as reliance on the technology for applications ranging from green energy storage to electric mobility increases. The measurement of short-term and long-term volume expansion in lithium-ion battery cells is relevant for several reasons. For instance, it provides information about the quality and homogeneity of battery cells during charge and discharge cycles, as well as aging over it’s lifetime. The expansion measurements are useful for the evaluation of new materials and the improvement of end-of-line quality tests during cell production. These measurements may also indicate the safety of battery cells by aiding in predicting state of charge and state of health over the lifetime of the cell. Expansion measurements can also assess inhomogeneities on the electrodes and defects such as gas accumulation and lithium plating. In this review, we first establish the known mechanisms through which short term and long term volume expansion in lithium-ion battery cells occurs. We then explore the current state-of-the-art for both contact and non-contact measurements of volume expansion. This review compiles existing literature to outline the various options available to researchers aiming to make ex situ volume expansion measurements by doing post mortem analyses on individual components and in operando measurements on entire battery cells. Finally, we discuss the different considerations when selecting an appropriate measurement technique. The selection of the optimal method for measuring battery cell expansion depends on the objective of the characterization, duration, required resolution, and repeatability of results. Costs and required space for the measurement equipment are also considered.

The aim of this research was to analyze the impact of implemented erosion control works (ECW) on soil erosion intensity in the watershed of the Ćelije reservoir (Rasina River) in the period between 1968 and 2022. The Erosion Potential Method was used to calculate the annual gross erosion (W), sediment transport (G), and erosion coefficient (Z) in the study area. As a result of the performed ECW there was a general decreasing trend in the intensity of soil erosion processes in the last 54 years. The specific annual gross erosion was 1189.12 m3/km-2/year-1 in 1968, while in 2022 it was 554.20 m3/km-2/year-1. The specific sediment transport was 540.18 m3/km-2/year-1 in 1968 and 253.55 m3/km-2/year-1 in 2022. Due to the changes in the intensity of erosion processes the specific annual gross erosion decreased by 634.92 m3/km-2/year-1, and the specific sediment transport by 286.63 m3/km-2/year-1. The erosion coefficient was reduced from Z=0.62 to Z= 0.35. A dependence between the slope of siltation and the natural bed slope was defined. The results show a significant correlation between erosion intensity and performed ECW, providing a basis for future watershed management and defining a strategy for soil erosion control in the Ćelije reservoir watershed.

This article discusses an international scientific expedition to Greenland that researched geography, geodesy, botany, and glaciology of the area. The results here focus on the geodetic and glaciological results obtained with the eBee drone in the eastern part of Greenland at the front of the Knud Rasmussen glacier. From two overflights nearby the glacier front, it was possible to obtain the speed of the glacier flow and the distribution of velocities in the glacier stream. The results correlate with other measurement methods and this technology has been shown as feasible. Of course, there are more accurate and long-term options or devices for monitoring the flow of glaciers. In this case of short-term visits to the site, the possibility of using a drone is interesting and the results show not only the flow speed of the glacier, but also the shape and structure from a height of up to 200m. The second part of the paper focuses on the analysis of modern satellite images of the Knud Rasmussen glacier from Google Earth (Landsat series 1984-2016) and a comparison with historical aerial images from 1932-1933. Experimentally, historical images were processed photogrammetrically into a 3D model.

The aim of this research work is to study the influence of temperature, solar irradiation and wind dust on the production of solar energy. In addition, it aims to study the assessment of water quality, in particular groundwater used for cooling and cleaning photovoltaic panels (quality analysis). it's an important source, stable and sustainable can be used entirely for cooling and cleaning PV modules from the sales dust, in order to improve their performance. To date, all research studies carried out in this context of cooling and cleaning using water have not taken account of the nature of this water. We have taken a sample of water from a well in a rural area in the Darra Tafilalet region of Morocco. This region has an arid and semi-arid climate, with very high temperatures and dust-laden winds, particularly in summer. These meteorological characteristics influence the efficiency of cells, particularly photovoltaic (PV) panels, reducing their performance. Next, the water sample was analysed in the laboratory. The results obtained show that the groundwater in this area is very sensitive to cooling and cleaning photovoltaic panels. Moreover, these results indicate that the temperature, solar irradiation and wind-blown dust have a significant influence on energy production.

This paper investigates an innovative photovoltaic cell configuration, denoted as “Au/CuSCN/RbGeI3/CdTe/ZnO/TiO2/FTO", using SCAPS-1D simulation. The research focuses on optimizing device performance by analyzing key components, including ZnO as the electron transport layer (ETL), RbGeI3 as the perovskite absorber layer, CuSCN as the hole transport layer (HTL), and CdTe as the active buffer layer. A comparison is made with the standard “Au/CuSCN/CH3NH3SnI3/CdTe/ZnO/TiO2/FTO" configuration under dark and illuminated conditions. Through an in-depth investigation involving temperature effects, generation rate analysis, RbGeI3 absorber layer thickness, Nd level, and interface defect levels, an optimized design for a unit area is achieved. The proposed solar cell demonstrates outstanding performance metrics, including an open circuit voltage (Voc) of 0.94V, a short circuit current density (Jsc) of 34.52mA/cm2, a fill factor (FF) of 77.77%, and an energy conversion efficiency (η) of 25.40%. These values significantly outperform the reference models with energy conversion efficiencies of 10.11% and 21.09%. Real-world applicability is validated by implementing these optimized characteristics in a photovoltaic system for Pakistan’s geographical location using PVSyst software. The suggested solar cell achieves a remarkable performance ratio (PR) of 85.6%, surpassing the PR of the reference basic solar cell model at 83%. The findings of this research offer a promising and superior solar cell design, incorporating innovative materials and optimization techniques to achieve exceptional energy conversion efficiency and overall performance. This study’s outcomes have the potential to advance photovoltaic technology and contribute to sustainable energy solutions worldwide.

Presently, Jordan confronts a double substantial challenge of enhancing energy security and mitigating greenhouse gas emissions. One of the most encouraging avenues to attain the objectives of sustainable development, energy security, and environmental conservation is to enhance the integration of renewable energy into the generation of electricity. In pursuit of this goal, the Jordanian government intends to expand investments in the green energy sector, with solar and wind energy poised to play a key role in satisfying energy demands and cultivating an environmental sustainability. This paper aims to examine the distinctive dynamics, challenges, obstacles, and potential solutions corresponding to the establishment of community solar and wind farms in Jordan suburban areas. It aims to highlight the opportunities and barriers influencing the track of sustainable energy adoption in the country. Through a comprehensive analysis of the Jordanian context, the goal is to extract insights that can guide policies and practices. Additionally, the findings may serve as a valuable benchmark for other regions confronting similar challenges on their pursuit for a sustainable energy future.

One of the strategies to reduce the contents of the low density lipoproteins (LDLs) in a blood is a hemoperfusion, in which case they are selectively retracted from plasma by an adsorber located outside the patient body. Recently, a photo-controllable smart surface was developed for this purpose characterised by high selectivity and reusability [C.Guo et al., ACS Applied Materials & Interfaces 2022, DOI:10.1021/acsami.2c07193]. We present a mesoscopic model for such a setup involving the azobenzene-containing polymer brush and the model LDL particles. The latter comprise an uniform spherical core covered by a shell of elongated particles representing phospholipids. The system is studied using the coarse-grained molecular dynamics simulation. We examined the dependences of the binding energy on both the length of polymer chains and the grafting density of a brush, and established optimal conditions for the adsorption. These are explained by a competition between the concentration of azobenzenes and phospholipids in the same spatial region, flexibility of polymer chains, and excluded volume effects.

Cyclin dependent kinase 1 (CDK1) has been primarily identified as a key cell cycle regulator in both mitosis and meiosis. Recently, an extramitotic function of CDK1 emerged when evidence was found that CDK1 is involved in many cellular events that are essential for cell proliferation and survival. In this review we summarize the involvement of active CDK1 in the initiation and elongation steps of protein synthesis in eukaryotes. During its activation CDK1 influences the initiation of protein synthesis, promotes the activity of specific translational initiation factors and affects the functioning of a subset of elongation factors. Our review provides insights into gene expression regulation during the transcriptionally silent cell cycle/M-phase and describes quantitative and qualitative translational changes based on the extramitotic role of the cell cycle master regulator CDK1, to optimize temporal synthesis of proteins to sustain division-related processes: mitosis and cytokinesis.

The article analyses the main aspects of upstream social marketing for implementing of mobile government (MGov). The methodology of current research is based on the systematic literature review in the fields of MGov and social marketing. According to our findings, most researchers investigated MGov from the side of citizens (consumers) and emphasised the benefits to them while changing their attitudes and behaviours in employing mobile applications. However, as there is a lack of the researches from the side of governmental bodies, in this paper, we were contrary looking for new meanings, attitudes and values from their perspective. Limitations of employment of MGov occur due knowledge gap among decision makers and public policy formers (upstream audience). Therefore, we argue that upstream social marketing for the upstream audience would bring the success in faster MGov implementation. Specific social marketing would be mostly valuable on the municipal level that is the closest substance to the society. Thus, in our paper we emphasise the benefit of the MGov for the local upstream audience and propose possible external marketers as well as the motivating theses based on these 7P of marketing mix for the successful MGov on municipal level.

Leather waste was carbonized at 800 °C in inert atmosphere. The resulting biochar was coated in situ with polypyrrole nanotubes produced by the oxidation of pyrrole in the presence of methyl orange. The composites of carbonized leather with deposited polypyrrole nanotubes of various composition were compared with similar composites based on globular polypyrrole. Their molecular structure was characterized by infrared and Raman spectra. Both conducting components formed a bicontinuous structure. The resistivity determined by four-point van der Pauw method was monitored as a function of pressure applied up to 10 MPa. The typical conductivity of composites was of the order of tenths to units S cm−1 and it was always higher for polypyrrole nanotubes than for globular polypyrrole. The conductivity decreased by 1–2 orders of magnitude after treatment with ammonia but still maintained a level acceptable for applications operating under non-acidic conditions. The composites were tested for dye adsorption, viz. cationic methylene blue and anionic methyl orange, using UV-spectroscopy. The composites are designed for the future use as functional adsorbents controlled by the electrical potential.

Land price sustainability issues have been addressed by many authors in the past. Most of these researchers used land prices (from land price maps) as the primary data source in their studies. Only a few papers analysed official land price maps, which are available very rarely. For this reason, we studied the spatial and temporal changes of land prices in the city of Olomouc based on an analysis of official land price maps from 1993 to 2017. We proposed several research hypotheses to confirm some general statements about land price development. We concluded that some macroeconomic indicators had a significant impact on changes in land prices. In the residential and commercial areas and historical centre, land prices are significantly higher than in other monitored aspects (land-use types). We also concluded that no link existed between land-use stability and land price stability. Surprisingly, no long-term stable areas were found in the area of interest. The analysis also confirmed that land price and its change over time varied in different spatial aspects. Surprisingly, the smallest influence was reflected in the economic aspect. Regarding natural events in recent decades, we observed a significant drop in land prices in the vicinity of watercourses threatened by flooding. These findings can assist in better understanding local development and changes in land price.

The spectra and global distributions of the X-ray emissions generated by the solar wind charge-exchange (SWCX) process in the terrestrial magnetosheath are investigated based on a global hybrid model and a global geocoronal hydrogen model. The solar wind O6+ ions which are the primary charge state for oxygen ions in solar wind are considered. The line emissivity of the charge-exchange born O5+ ions are calculated by Spectral Analysis System for Astrophysical and Lab oratory (SASAL). It is found that the emission lines from the O5+ ranges from 105.607 to 118.291 eV with the strong line at 107.047 eV. We then simulated the magnetosheath X-ray emission intensity distributions with a virtual camera at two positions of north pole and dusk at six stages during the passing of a perpendicular interplanetary shock combined with a tangential discontinuity structure through the Earth’s magnetosphere. During this process, the X-ray emission intensity increases with time, and the maximum value is 27.11 keV cm-2 s-1 sr-1 on the dayside, which is 4.5 times that before the solar wind structure reaches the Earth. A clear shock structure can be seen in the magnetosheath and moves earthward. The maximum emission intensity seen at dusk is always higher than that seen at north pole.

The per capita availability of freshwater resources on a global scale is gradually decreasing due to population growth, rapid urbanization, industrialization, and modern lifestyles. In this situation, wastewater management becomes a major concern. Conventional treatment processes used to treat wastewater discharges are not adequate for the advanced removal of pollutants, especially refractory organic pollutants, which are mainly organic compounds that are not easily biodegradable in the environment. The use of photocatalytic membrane reactors (PMRs) for tertiary wastewater treatment has attracted much interest in recent periods, and various configurations have been investigated. The performance of a PMR using an iron doped titanium photo catalyst and Polysulfone-based polymeric membrane for municipal wastewater treatment was evaluated under natural and simulated solar light. Obtained results proved that solar driven PMRs can remove organic loading (COD) with high efficiencies and may represent a suitable alternative for the tertiary treatment step of municipal wastewater.

Solar photovoltaic (PV) generation suffers from multiple serious issues, for example shading effects directly affect the performance of installed PV arrays. By studying these issues, it can play a key role in improving the limitations and performance of PV panels. The study of PV arrays under partial shading conditions is mentioned in many papers as a part of other studies and as an independent phenomenon. Therefore, it is essential to improve these studies and update them with new research and study this problem in detail to know how to limit the effects of partial shading irradiance conditions on PV arrays performances, including economical aspects. This paper proposes to study the effects of different partial shading irradiance conditions for a PV array in various configurations. The analysis is proved in detail through the simulation of the proposed PV array in the Matlab/Simulink environment. The obtained results show the performances of interconnected PV arrays under different partial shading irradiance and temperature conditions, including the solar array I-V and P-V characteristics. In addition, different PV array configurations with and without bypass and blocking protection diodes improve and minimize the effect of partial shading conditions and avoid the reductions in output power.

This publication aims to create 4K UHD video sequences with a specific focus on smart cities and transport. The created database will be accessible to all experts in the field and can be further used for research purposes. All reference video sequences will be transcoded into different quality settings. The resolution, compression standard, and bitrate will be changed. The work will aim to find out the best combination of video parameters from the measured values. Thanks to the overall evaluation, we will ensure for each single video sequence the quality with the best experience for the providers that will offer the service. The database will also be available with its objective and subjective ratings, with dynamicity information characterized by spatial and temporal information. After, It will be possible to compare the results of the subjective evaluation of a selected sample of our respondents with the work of other researchers who can evaluate with a different sample of evaluators.

In order to achieve the elimination of the negative impacts of transport on road safety, the European Union is taking various measures resulting from its commitment to improve road safety. One of the instruments for achieving the objectives set is social legislation for the work of drivers in road freight and passenger transport. In line with the objective of improving the quality of working conditions for road transport drivers and road safety, the European Union applies Regulation (EC) No 561/2006 on the harmonisation of certain social legislation relating to road transport, which lays down rules on driving times, breaks and rest periods for drivers operating in road freight and passenger transport. The main objective of the paper is to assess the impact of social legislation on road transport safety by means of real research and to identify the factors influencing the violation of the legislation depending on the type of transports carried out in domestic or international road freight transport.

The Sun is a huge gaseous body. However, we cannot observe events in the inner Sun due to the convection zone opacity according to previous models. Therefore, the flares originate from the front surface of the Sun. But the current study relied on the distance distribution of X-Ray solar flares, which concluded that the inner layers have much lower opacity than expected. It is even less than what was expected by the latest models based on helioseismology. This means that the flares may originate from the solar interior or solar core, and perhaps from the backside surface, and even appear to us from the frontside surface. Which the re-estimate and correct the currently listed solar flare’s location is needed. Additionally, the flare’s distance illustrations the solar interior layers and appears their boundaries from the core to the photosphere. This method allows us to monitor the variation of the core’s radius with time. The model of the flare’s distance has been developed in current study. But this needs to redevelopment after re-estimating the solar flares locations.

Solar flares are broadly classified as impulsive or gradual. Ions accelerated in a gradual flare are thought to be accelerated through a shock acceleration mechanism, but the particle acceleration process in an impulsive flare is still largely unexplored. To understand the acceleration process, it is necessary to measure the high-energy gamma-rays and neutrons produced by the impulsive flare. Under such circumstances, on November 7, 2004, a huge X2.0 flare occurred on the solar surface, where ions were accelerated to energies greater than 10 GeV. The accelerated primary protons collided with the solar atmosphere and produced line gamma-rays and neutrons. These particles were received as neutrons and line gamma-rays, respectively. Neutrons of a few GeV, on the other hand, decay to produce secondary protons while traveling 0.06 au in the solar-terrestrial space. These secondary protons arrived at the magnetopause. Although the flux of secondary protons is very low, the effect of collecting secondary protons arriving in a wide region of the magnetosphere (the Funnel or Horn effect) has resulted in significant signals being received by the solar neutron telescope at Mt. Sierra Negra (4,600 m). This information suggests that ions on the solar surface are accelerated to over 10 GeV with an impulsive flare.

In this study, we present comprehensive climatologies of effective ultraviolet (UV) quantities and photosynthetically active radiation (PAR) over Cyprus for the period 2004 to 2023, leveraging the synergy of earth observation (EO) data and radiative transfer model simulations. The EO dataset, encompassing satellite and re-analysis data for aerosols, total ozone column, and water vapor, alongside cloud modification factors, to capture the nuanced dynamics of Cyprus's atmospheric conditions. With a temporal resolution of 15 minutes and a spatial of 0.05°x0.05°, these climatologies undergo rigorous validation against established satellite datasets and are further evaluated through comparisons with ground-based global horizontal irradiance measurements provided by the Meteorological Office of Cyprus. This dual-method validation approach not only underscores the models' accuracy but also highlights their proficiency in capturing intra-daily cloud coverage variations. Our analysis extends to investigating the long-term trends of these solar radiation quantities, examining their interplay with changes in cloud attenuation, aerosol optical depth (AOD), and total ozone column (TOC). Significant decreasing trends in the noon ultraviolet index (UVI), of -2 to -4% per decade have been found in Autumn, especially marked on the island’s Northeastern part, mainly originating from the (significant) positive trends in TOC. The significant decreasing trends in TOC, of -2 to -3% per decade that were found in Spring do not result in correspondingly significant positive trends in the noon UVI since variations in cloudiness and aerosols also have a strong impact on the UVI in this season. The seasonal trends in the Daylight Integral (DLI) were generally not significant. These insights provide a valuable foundation for further studies aimed at developing public health strategies and enhancing agricultural productivity, highlighting the critical importance of accurate and high-resolution climatological data.

Redox mediators comprising I–, Co3+, and Ti3C2Tx MXene were applied to dye-sensitized solar cells (DSCs). In the as-prepared DSCs (I-DSCs), wherein hole conduction occurred via the redox reaction of I−/I3− ions, the power conversion efficiency (PCE) was not altered by the addition of Ti3C2Tx MXene. The I-DSCs were exposed to light to produce Co2+/Co3+-based cells (Co-DSCs), wherein the holes were transferred via the redox reaction of Co2+/Co3+ ions. A PCE of 9.01% was achieved in a Co-DSC with Ti3C2Tx MXene (Ti3C2Tx-Co-DSC), which indicated an improvement from the PCE of a bare Co-DSC without Ti3C2Tx MXene (7.27%). It was also found that the presence of Ti3C2Tx MXene in the redox mediator increased the hole collection, dye regeneration, and electron injection efficiencies of the Ti3C2Tx-Co-DSC, leading to an improvement in both the short-circuit current and the PCE when compared with those of the bare Co-DSC without MXene.

The quiet-time solar wind electrons feature non-thermal characteristics when viewed from the perspective of their velocity distribution functions. They typically have an appearance of being composed of a denser thermal “core” population plus a tenuous energetic “halo” population. At first, such a feature was empirically fitted with the Kappa velocity space distribution function, but ever since the ground-breaking work by Tsallis, the space physics community has embraced the potential implication of the Kappa distribution as reflecting the non-extensive nature of the space plasma. From the viewpoint of microscopic plasma theory, the formation of non-thermal electron velocity distribution function can be interpreted in terms of the plasma being in a state of turbulent quasi equilibrium. Such a finding brings forth the possible existence of a profound inter-relationship between the non-extensive statistical state and the turbulent quasi-equilibrium state. The present paper further develops the idea of solar wind electrons being in the turbulent equilibrium, but unlike the previous model, which involves the electrostatic turbulence near the plasma oscillation frequency (i.e., Langmuir turbulence), the present paper considers the impact of transverse electromagnetic turbulence, particularly, the turbulence in the whistler-mode frequency range. It is found that the coupling of spontaneously-emitted thermal fluctuations and the background turbulence leads to the formation of non-thermal electron velocity distribution function of the type observed in the solar wind during quiet times. This demonstrates that the whistler-range turbulence represents an alternative mechanism for producing the Kappa-like non-thermal distribution, especially close to the Sun and in the near-Earth space environment.

Cyprus plans to drastically increase the share of renewable energy sources from 13.9% in 2020 to 22.9% in 2030. Solar energy can play a key role in the effort to fulfil this goal. The potential for production of solar energy over the island is much higher than most of European territory because of the low latitude of the island and the nearly cloudless summers. In this study, high quality and fine resolution satellite retrievals of aerosols and dust, from the newly developed MIDAS climatology, as well as information for clouds from CMSAF are used in order to quantify the effects of aerosols, dust, and clouds on the levels of surface solar radiation (SSR) and the corresponding financial loss for different types of installations for production of solar energy. An SSR climatology has been also developed based on the above information. Ground-based measurements were also incorporated to study the contribution of different species to the aerosol mixture and the effects of day-to-day variability of aerosols on SSR. Aerosols attenuate 5 – 10% of annual GHI and 15 – 35% of annual DNI, while clouds attenuate ~25 – 30% and 35 – 50% respectively. Dust is responsible for 30 – 50% of the overall attenuation by aerosols.

A flow chart is presented depicting coupling in ocean-atmosphere system, initiated by solar decadal variability that involves El Niño Southern Oscillation (ENSO). Possible mechanisms for Canonic ENSO, Modoki ENSO and Canonic-Modoki ENSO are proposed considering their relevance to the decadal variation of Hadley, Walker circulation and mid-latitude jets. It also discusses subsequent teleconnections by ENSO on Indian Summer Monsoon (ISM) with a special emphasis on later two decades of the last century. Possible mechanisms relating to a disruption of the usual ENSO-ISM teleconnection for those decades are emphasised; the role of volcanos and the change in the sun- NAO (North Atlantic Oscillation) connection were attended. The regional Hadley circulation, via the NAO in the northern hemisphere and Indian Ocean Dipole in the southern hemisphere, during that period, may have a role in the change in ISM behaviour- which though captured in observation but missed by models. The representation of flow chart helps to improve understanding of various types of ENSO in both temporal as well as spatial scale. The overall study subsequently can benefit the modelling community by not only improved the representation of ENSO in models but also better representation of ISM teleconnection via regional Hadley cell.

One of the main problems is handling rainwater management in urban areas is water quality from urban run-off. Currently, the emphasis is on using rainwater in cities as much as possible. The concentration of pollutants is the most problematic in rainwater. After precipitation falls on surfaces, surface water is immediately contaminated. This pollution must be cleaned or contained and transported to a wastewater treatment plant through the sewer network. Among the primary pollutants that we can identify in surface water are, for example, heavy metals. In our research, we focus on the analysis of real surface waters taken from 13 lo-cations on the territory of the Slovak Republic. The result of the research is an analysis of the suitability of reusing these waters. From the results of the analyses, it is clear that not a single sample is suitable for irrigation, as the limits of at least one monitored parameter were exceeded in all samples. The monitored lead concentration parameter was exceeded in all monitored samples.

Chromium-nickel austenitic stainless steels are widely used due to their high corrosion resistance, good weldability and deformability. To some extent, their application is limited by their mechanical characteristics. As a result of their austenitic structure, increasing the static and dynamic strength of the components can be achieved by surface cold work. Due to the tendency of these steels to undergo intercrystalline corrosion, another approach to improve their mechanical characteristics is the use of low-temperature thermo-chemical diffusion processes. This article proposes a new combined process based on sequentially applied diamond burnishing (DB) and low-temperature gas nitriding (LTGN) to optimally improve the fatigue strength of 304 steel. The essence of the proposed approach is to combine the advantages of the two processes (DB and LTGN) to create a zone of residual compressive stresses in the surface and subsurface layers–the enormous surface residual stresses (axial and hoop) introduced by LTGN, with the significant depth of the compressive zone characteristic of static surface cold working processes. DB (both smoothing and single-pass hardening), in combination with LTGN, achieves a fatigue limit of 600 MPa, an improvement of 36.4% compared to untreated specimens. Individually, smoothing DB, single-pass DB and LTGN achieve 540 MPa, 580 MPa and 580 MPa, respectively. It was found that as the degree of plastic deformation of the surface layer introduced by DB increases, the content of the S-phase in the nitrogen-rich layer formed by LTGN decreases, with resultant increased content of -phase, and a new (also hard) phase: stabilized nitrogen-bearing martensite.

Major (exo)planetary and satellite bodies seem to concentrate at intermediate areas of the radial 1 distributions of all the objects orbiting in each (sub)system. We show that angular-momentum transport during secular evolution of (exo)planets and satellites necessarily results in the observed intermediate accumulation of the massive objects. We quantify the ‘middle’ as the mean of mean motions (orbital angular velocities) when three or more massive objects are involved. Radial evolution of the orbits is expected to be halted when the survivors settle near mean-motion resonances and angular-momentum transfer between them ceases (gravitational Landau damping). This dynamical behavior is opposite in direction to what has been theorized for viscous and magnetized accretion disks, in which gas spreads out and away from either side of any conceivable intermediate area. We present angular momentum transfer simulations in few-body systems, and we calculate the tidal dissipation timescales and the physical properties of the mean tidal field in planetary and satellite (sub)systems.

Background: As the only place in a store where all customers must pass through and wait, the checkout lane may be particularly influential over consumer purchases. Because most foods and beverages sold at checkout are unhealthy (e.g., candy/sweets, sugar-sweetened beverages, and salty snacks), policymakers and advocates have expressed growing interest in healthy checkout policies. To understand the extent to which such policies could improve nutrition equity, we as-sessed the prevalence and sociodemographic correlates of purchasing items from checkout. Methods: We assessed self-reported checkout purchasing and sociodemographic characteristics in a national convenience sample of adults (n=10,348) completing an online survey in 2021. Re-sults: Over one-third (36%) of participants reported purchasing foods or drinks from checkout during their last grocery shopping trip. Purchasing items from checkout was more common among men; adults <55 years of age; low-income consumers; Hispanic, non-Hispanic American Indian and Alaska Native, and non-Hispanic Black consumers; those with at least a bachelor’s degree; parents; and consumers diagnosed with type 2 diabetes or pre-diabetes (p-values<0.05). Conclusions: Purchasing foods or beverages from store checkouts is common and more prevalent among low-income and racial and ethnic minority groups. These results suggest that healthy checkout policies have the potential to improve nutrition equity.

To achieve efficient and durable consolidation of weathered sandstone, the selection of a suitable consolidant is essential. To reasonably assess the suitability of different formulations, it is fundamental to compare their performance as a consolidant within a substrate, which reliably models the properties of deteriorated material. As a test substrate, the sandstone from quarries in Mšené in central Bohemia was selected, for its developed porosity and relatively low mechanical strength. To obtain relevant comparison of their application potential, both commercial (Remmers KSE OH and Surfapore) and self-developed consolidants were included. To test the long-term stability of each consolidant, the stone was subjected to accelerated weathering. The characterization of texture properties was based on the physical sorption of nitrogen and krypton, mercury intrusion porosimetry and water uptake. While the mechanical properties in microscale were determined by nanoindentation, the mechanical strength in macroscale before and after consolidation was measured by drilling resistance. Both commercial exhibited good mechanical performance with reasonable durability. The performance of our developed samples was comparable or, in some cases, superior. Very interesting were the consolidants containing TiO2 and ZnO nanoparticles, the former exhibiting comparable degree of consolidation and durability as commercial ones, with additional photocatalytic function, the latter unusually high increase in the mechanical strength, even after the weathering test. The diammonium hydrogen phosphate based consolidant showed exceptional durability in the weathering test, which makes it a promising product not only for carbonate but also sandstone materials.

The new slide roller burnishing (SRB) method has been developed to produce mirror-like surfaces. Unlike conventional roller burnishing (RB), SRB is implemented through a unique device that allows the axes of the deforming roller and the rotary workpiece to cross resulting in a relative sliding velocity that can be controlled (in magnitude and direction) by varying the crossing angle. In the present work, the effect of SRB on the fatigue behavior of AISI 316 steel fatigue specimens was investigated by comparing with a conventional RB using the basic correlation in surface engineering: finishing–surface integrity (SI)–operating behavior. To obtain a more representative picture of the comparison, we implemented each method (RB and SRB) with two combinations of governing factors: (A) a radius of the roller toroidal surface of 3 mm, a burnishing force of 250 N and feed rate of 0.05 mm/rev (RB-A and SRB-A) and (B) a radius of the roller toroidal surface of 4 mm, a burnishing force of 550 N and feed rate of 0.11 mm/rev (RB-B and SRB- B). Both SRB-A (crossing angle of –45°) and SRB-B (crossing angle of –30°) achieved mirror-finish surfaces. SRB-B lead to the greatest fatigue strength and, thus, the longest fatigue life among all tested processes. SRB-B created the deepest zone (&gt;0.5 mm) with residual compressive macro-stresses and a clearly defined modified surface layer, whose thickness of more than 20 m is about twice that created by the other three processes.

Aluminium bronzes possess a unique combination of high strength and wear and corrosion resistance in aggressive environments; thus, these alloys find wide application in marine, shipbuilding, aviation, railway, offshore platform applications and other fields. Iron-aluminium bronzes (IABs) are the cheapest and most widely used. When the aluminium content is above 9.4 wt%, IAB is biphasic (i.e. it undergoes -transformation) and can be subjected to all heat-treatment types depending on the desired operating behaviour of the bronze component. This article presents correlations (mathematical models) between the primary mechanical characteristics (yield limit, tensile strength, elongation, hardness and impact toughness) and the ageing temperature and time of quench at 920°C in water Cu-11Al-6Fe bronze, obtained using the centrifugal casting method. The microstructure evolution was evaluated depending on the ageing temperature and time changes. Overall, the research was conducted in three successive inter-related stages: a one-factor-at-a-time study, planned experiment, and optimisations. Four optimisation tasks, which have the greatest importance for practice, were formulated and solved. The defined multiobjective optimisation tasks were solved by searching for the Pareto-optimal solution approach. The decisions were made through a nondominated sorting genetic algorithm (NSGA-II) using QstatLab. The optimisation results were verified experimentally. Additional samples were made for this purpose, quenched at 920°C in water and subjected to subsequent ageing with the optimal values of the governing factors (ageing temperature and time) for the corresponding optimisation task. The comparison of the results for the mechanical characteristics with the theoretical optimisation results presents good agreement.

In this study, we performed periodicity analyzes of selected daily solar (FI, CI), geomagnetic (Ap, Dst, Scalar B) and cosmic (CRI) activity indices for the last solar Cycle 24 (December 2008 to December 2019). To investigate the periodic variations of above selected data sets the Multi Taper Method (MTM), Morlet wavelet, Cross Wavelet Transform (XWT), and Wavelet Coherence (WTC) analysis techniques were used. In results of our analysis we found that i) the 25-33 and 2048-day periodicities exist in all data sets without any exception, while all other detected periodicities have data preferences, ii) all detected periods located around the maximum phase of the cycle (Cycle 24), iii) the phase relations between compared data sets periodicities are gradually changing from small periods to large ones; there are no phase relations between small periodicities and they show mixed phases, while they are completely in phase/antiphase for large periodicities, iv) all detected FI periodicities, except 2048 days periodicity, are common periodicities with all other data sets used in this study.

Origin, mechanics and properties of the Solar System are analysed in the framework of the Complete Relativity theory (by the same author). According to Complete Relativity, everything is relative. Any apparent absolutism (notably invariance to scale of dimensional constants, absolute elementariness, invariance to time) is an illusion stemming from limits imposed by [or on] polarized observers that will inevitably lead to misinterpretation of phenomena (another illusion) occurring on non-directly observable scales or even on observable but distant scales in space or time. If everything is relative, reference frames will exist where particles are planets and where planets are living beings. Earth is, therefore, analysed here in more detail, both as a particle and, as a living evolving being (of, hypothesized, extremely introverted intelligence). The analysis confirms the postulates and hypotheses of the theory (ie. existence of discrete vertical energy levels) with a significant degree of confidence. During the analysis, some new hypotheses have emerged. These are discussed and confirmed with various degrees of confidence. To increase confidence or refute some hypotheses, experimental verification is necessary. Main conclusions that stem from my research and are further confirmed in this paper are: universes are, indeed, completely relative; Solar System is a scaled (inflated, in some interpretations) Carbon isotope with a nucleus in a condensed (bosonic) state and components in various vertically excited states; life is common everywhere, albeit extroverted complex forms are present on planetary surfaces only during planetary neurogenesis; anthropogenic climate change is only a part (trigger from one perspective) of bigger global changes; major extinction events on a surface of a planet are relative extinctions, a regular part of transformation and transfer of life in the process of planetary neurogenesis.

The result of the multidisciplinary collaboration of researchers from different areas of knowledge to validate a solar radiation model is presented. The MAPsol is a 3D local-scale adaptive solar radiation model that allows to estimate direct, diffuse and reflected irradiance for clear sky conditions. The model includes the adaptation of the mesh to complex orography and albedo, and considers the shadows cast by the terrain and buildings. The surface mesh generation is based on surface refinement, smoothing and parameterisation techniques and allows the generation of high quality adapted meshes with a reasonable number of elements. Another key aspect of the paper is the generation of a high-resolution digital elevation model (DEM). This high-resolution DEM is constructed from LiDAR data and its resolution if two times more accurate than the publicly available DEMs. The validation process uses direct and global solar irradiance data obtained from pyranometers at the University of Salamanca located in an urban area affected by systematic shading from nearby buildings. This work provides an efficient protocol for studying solar resources, with particular emphasis on areas of complex orography and dense buildings where shadows can potentially make solar energy production facilities less efficient.

Almost all single-family detached house in Canada consume huge electricity for space heating and domestic hot water (DHW) purposes. There are many possibilities to design an energy-efficient house. A solar water heating system can be used for domestic water and space heating. Water temperature can be kept constant always by connecting a heat pump or oil burner because solar energy is intermittent. Proper and optimized solar photovoltaic and collector design, tank design, heat pump selection, house insulation, total demand calculation in each section are essential. Energy-Efficient house design has been proposed with water heating and space heating system and compared with the existing system, solar PV based systems, and solar collector based system. The tracking and non-tracking based solar thermal collector based and the solar photovoltaic based system has been compared in this paper and investigate the suitable one for practically applicable and acceptable by the people. Simulation has been done by using the PolySun software. It found that by implementing the proposed PV based system with tracking is highly suitable considering lower cost, high output power, flexibility, easy installation.

In this work, two plasmonic structures with two different periodic nanostructures (nanodisk and nanostrip arrays) separated from the gold layer by an ultrathin dielectric Al2O3 layer are proposed, and their optical properties are simulated as 3-dimensional models using COMSOL Multiphysics software tool. The optical responses, such as the amplification of the electric field and the scattering, absorption and extinction cross sections of the two structures, are investigated and compared. The results show that both structures show strong field enhancement in their gap layer, and the structure with the periodic array of metal nanodisks shows stronger field enhancement and larger absorption, extinction, and scattering cross sections in its dipole resonance wavelength, which is defined as a bright plasmonic mode. In addition, some weaker resonant modes are observed for both structures and the reason for their generation is dis-cussed. The analysis of different possible modes in such structures is crucial for their application in various fields.

Emerald ash borer (EAB), Agrilus planipennis, an invasive phloem-boring beetle, was detected in the Luhansk Region of Ukraine in 2019. In the following years, it expanded to a large part of the Kharkiv region and the parks of Kyiv. Previous research proved that the climate in Luhansk and neighboring regions is favorable for EAB, and the lack of a host plant (Fraxinus sp.) cannot prevent pest expansion in Ukraine. Considering the necessity to detect inhabited trees in time, our current research aimed to identify the most attractive EAB forest subcompartments considering forest site conditions and stand structure. MaxEnt model predicted the potential distribution of EAB with high accuracy (AUC = 0.842). The most significant five variables provided 82.9% to the model, particularly «Age of trees, years», «Area of forest subcompartment, ha», «Mean height of trees, m», «The proportion of Fraxinus excelsior in the stand composition, %», and «Hygrotope index (humidity level), point». A very high probability of EAB expansion in the Luhansk region (&gt;90 %) is predicted at 20 % of the forest area with Fraxinus sp. in the stand composition. The probability of EAB spread above 30% is predicted for 75 % of such area. To improve the forecasting accuracy, it could be necessary to consider the data on road localization along which the pest can spread passively, as well as dominate wind speed.

The awareness of ciliate importance in freshwater has changed dramatically in the last decades, reflecting methodological attempts. We analysed two decades (1994-2018) of data on the surface (0-3 m) ciliate assemblage in the Slapy reservoir (Vltava River, Czech Republic) during two different nutrient-load defined periods. We identified, quantified, and evaluated the biomass of ciliates in the quantitative protargol-stained preparations. We used water age, nutrients, bacteria, heterotrophic nanoflagellates and rhodomonads as the main explanatory background variables. The sampling median and interquartile range data analysis and a non-metric multidimensional scaling were applied. Ciliates were grouped according to their feeding behaviour. The picoplankton filtering species dominated the assemblages in an annual mean (halteriids and minute strobilidiids followed by peritrichs). Algae hunters Balanion planctonicum, urotrichs and nanoplankton filtering tintinnids were important before the spring phytoplankton peak when a maximum of ciliate biomass reflected mixotrophic nanoplankton filtering pelagostrombidiids. Only there, ciliate biomass tightly followed their quantified prey. Heterotrophic and mixotrophic Askenasia and Lagynophrya were typical raptorial/flagellate hunters; only Mesodinium spp. peaked during autumn. The oligotrophication increased the ciliate assemblage biomass in the surface layer during the stratification in concordance with the PEG model.

At present, the world is now passing a very far different time than normal situation due to the COVID-19 pandemic crisis. The global life-style and human civilization is currently progressing with down-stream that affecting almost every sectors necessary for human civilizations except the current environmental situation. To control the COVID-19 spreading, most of the countries are following lockdown process that reduces human mobility, thus reducing the CO2 emission to the environment. Though the COVID-19 pandemic is a blessing for the present environment, however, the post-COVID world will face a massive thrust of energy and only conventional energy resources may not be enough to mitigate the energy demands. Solar power generation technology mainly the photovoltaic (PV) systems and their advancement can be the leading possibilities to minimize the gap between the power demand and generation. It is now time to think how we can improve the PV power generation in future and the post-COVID world. In this encyclopaedia communication, we report on Nano-technological approach to improve the conversion efficiency of GaAs solar cells. We have designed and optimized several types of nano-structured assemblies that can be implemented to reduce the front surface incident light reflection losses thus can assist to improve the conversion efficiency of GaAs solar cells.

One of the most interesting groups of fatty acid derivates is the group of conjugated fatty acids, from which the most researched are conjugated linoleic acid (CLA) and conjugated linolenic acid (CLNA), which are associated with countless health benefits. Sex pheromone mixture of some insect species, including tobacco horn-worm (Manduca sexta), are typical for the production of uncommon C16 long conjugated fatty acids with two and three conjugated double bonds, as opposed to C18 long CLA and CLNA. In this study, M. sexta desaturases MsexD2 and MsexD3 were expressed in multiple strains of Y. lipolytica with different genotypes. Experiments with supplementation of fatty acid methyl esters into the medium resulted in production of novel fatty acids. Using GCxGC-MS 20 new fatty acids with two or three double bonds were identified. Fatty acids with conjugated or isolated double bonds or combination of both were produced in trace amounts. Results of this study prove that Y. lipolytica is capable of synthesizing C16 conjugated fatty acids. Further genetic optimization of the Y. lipolytica genome and optimization of the fermentation process could lead to increased production of novel fatty acid derivatives with biotechnologically interesting properties.

This paper investigates the improvement in solar energy collection and conversion using Al₂O₃-Water nanofluids in a solar flat plate collector (SFPC). The efficiency of a solar flat plate collector using water as the fluid medium is analyzed experimentally and theoretically. For theoretical analysis, a mathematical model in MATLAB is used to simulate and is validated by the experimental results. To enhance the solar energy collection and conversion efficiency of the SFPC, Al₂O₃-Water nanofluid was selected as the fluid medium. The nanofluid properties like density, specific heat capacity, thermal conductivity and viscosity are analyzed and compared for several models of Al₂O₃-Water nanofluids and the best model was selected to modify the simulation. Effect of particle diameter in the nanofluid was found to be marginal on the nanofluid properties. The optimum volume concentration of the nanofluid was found to be 4% giving an efficiency increase of 7.78% in the SFPC over the use of water. This reduces the area of the SFPC by 10.5%.

We have shown that three astrometric solar-system anomalies can be explained satisfactorily by using evolutionary gravitational constant G and speed of light c in the Einstein’s field equation. These are: a) the Pioneer acceleration anomaly; b) the anomalous secular increase of Moon-orbit eccentricity; and c) the anomalous secular change in the astronomical unit AU. The gravitational constant G and the speed of light c both increase as dG/dt = 5.4GH₀ and dc/dt = 1.8cH₀ with H₀ as the Hubble constant. We also show that the Planck’s constant ħ increases as dħ/dt = 1.8ħH₀. Additionally, the new approach fits the supernovae Ia redshift vs distance modulus data as well as the standard ΛCDM model with just one adjustable parameter H₀.

To reduce solar power production invariance, it is critical to study varying patterns of power production in the concerned region. Analyzing the patterns of past power production trends can help simulate power production scenarios for future. The current study area is around Amsterdam, located in Netherlands. PVoutput.org website is used to mine 6 months of solar power production data for 120 stations around Amsterdam city. FME Workbench software is used to actively fetch the data from the mentioned website and manage in a MySQL database. Solar attenuation maps created using ArcGIS, helped to graphically visualize the variations in solar power production at different times and locations. Further, spatial autocorrelation is checked between the stations using semi-variograms in geostatistical tool of ArcMap. This feature allows to check whether the stations located close to each other are more correlated to each other rather than stations which are far apart. The statistical data analysis of power production can aid solar power production companies to better interpolate and predict solar power in advance for the concerned study region.

Hybrid organic/inorganic conducting and magnetic composites of core–shell type have been prepared by in-situ coating of nickel microparticles with polypyrrole. Three series of syntheses have been made. In the first, pyrrole was oxidized with ammonium peroxydisulfate in water in the presence of various amounts of nickel and the composites contained up to 83 wt% of this metal. The similar syntheses in 0.1 M sulfuric acid followed. Finally, the composites with polypyrrole nanotubes were prepared in water in the presence of structure-guiding methyl orange dye. FTIR and Raman spectroscopies confirmed the formation of polypyrrole. The resistivity of composite powders of the order of tens to hundreds Ω cm was monitored as a function of pressure up to 10 MPa. The resistivity of composites slightly increased with increasing content of conducting nickel. This apparent paradox is explained by the coating of nickel particles, which prevents their contacts and generation of metallic conducting pathways. Electrical properties were practically independent of the way of composite preparation or nickel fraction and were controlled by polypyrrole phase. On the contrary, magnetic properties were determined exclusively by nickel content. The composites were used as a solid phase to prepare a magnetorheological fluid. The test showed better performance when compared with a different nickel system.

We demonstrated an ITO-free, highly transparent organic solar cell with the potential to be integrated into window panes for energy harvesting purposes. A transparent, conductive ZnO/Ag/ZnO multilayer electrode and a Ag:Ca thin film electrode were used in this transparent device as the bottom and top electrode, respectively. To further improve the transmittance of the solar cell, the thickness of the top ZnO layer was investigated by both experiment and simulation. An average visible transmittance of > 60% was reached, with a maximum transmittance of 73% at 556 nm. Both top and bottom illumination of the solar cell generated comparable power conversion efficiencies, which indicates the wide application of this solar cell structure. In addition, we fabricated distributed Bragg reflector mirrors with sputtered SiO2 and TiO2, which efficiently increased the power conversion efficiency over 20% for the solar cells on glass and PET substrates,

The details of the solar flare production mechanisms are not yet completely understood. One of the standing questions is the anisotropy of the X-ray flux, especially in strong flares. It can be studied indirectly by analysing the characteristics of flares at different positions on the visible disc. In this paper, the durations, peak and integral fluxes of strong (X-class) solar flares from cycles 22--25 are considered with respect to their apparent position on the Sun. It is found that there exists a significant north--south asymmetry in all three parameters, which also varies depending on the phase of the solar cycle (with general predominance of the south). This confirms the results of previous studies. A weaker and less significant east--west asymmetry is found as well, partly supported by literature. A previously undetected centre-to-limb asymmetry is reported (in favour of the limb) in all three parameters. All three asymmetries are enhanced during the solar minimum, which could hint at their connection to the large scale magnetic structuring of the Sun. The prevalence of strong solar flares near the limb at the solar minimum has clear space weather warning implications.

This study refers to the optimization of a Selective Solar Absorber to improve the Sun-to-thermal conversion efficiency at mid temperatures in high vacuum flat thermal collectors. Efficiency has been evaluated by using analytical formula and a numerical thermal model. Both results have been experimentally validated using a commercial absorber in a custom experimental set-up. The optimization procedure aimed at obtaining Selective Solar Absorber is presented and discussed in the case of a metal dielectric multilayer based on Cr2O3 and Ti. The importance of adopting a real spectral emissivity curve to estimate high thermal efficiency at high temperatures in selective solar absorber is outlined. Optimized absorber multilayers can be 8% more efficient than the commercial alternative at 250 °C operating temperatures and up to 27% more efficient at 300 °C. Once the multilayer has been optimized the choice of a very low emissivity substrate such as copper allows to further improve efficiency and to reach stagnation temperature higher than 400 °C without Sun concentration.

Keywords: Artificial Neural Network (ANN), Support Vector Machine (SVM), Support Vector Regression (SVR), Lightweight Gradient Boosting Machines (Light GBM), Machine Learning, Solar Irradiance (SI), Solar forecasting

Quality control (QC) may be a lengthy and tedious process. As a result, most data users use data from meteorological services without performing data quality checks. The South African Weather Service (SAWS) re-established the national solar radiometric network comprising of 13 new stations within the six climatic zones of the country. This study reports on the performance results of the Baseline Surface Radiation Network (BSRN) QC procedures applied to the solar radiation data within the SAWS radiometric network. The overall percentage performance of the SAWS solar radiation network based on BSRN QC methodology is 97.79%, 93.64%, 91.6% and 92.23% for Long Wave Downward Irradiance (LWD), Global Horizontal Irradiance (GHI), Diffuse Horizontal Irradiance (DHI) and Direct Normal Irradiance (DNI) respectively with operational problems largely dominating the percentage of bad data. The overall average performance of the Surface Solar Radiation Dataset – Heliosat (SARAH) data records for the GHI estimation for all the stations showed a Mean Bias Deviation (MBD) of -8.28 Wm^-2, a Mean Absolute Deviation (MAD) of 9.06 Wm^-2 and the Root Mean Square Deviation (RMSD) of 11.02 Wm^-2. The correlation (quantified by R²) between ground-based and SARAH-derived GHI time series was ~ 0.98. The established network has the potential of providing high quality minute solar radiation data sets (GHI, DHI, DNI and LWD) and auxiliary hourly meteorological parameters vital for scientific and practical applications in renewable energy technologies in South Africa.

Solar and wind resources available for power generation are subject to variability due to meteorological factors. Here, we use a new global climate reanalysis product, Version 2 of the NASA Modern-Era Retrospective Analysis for Research and Applications (MERRA-2), to quantify interannual variability of monthly-mean solar and wind resource from 1980 to 2016 at a resolution of about 0.5 degrees. We find an average coefficient of variation (CV) of 11% for monthly-mean solar radiation and 8% for windspeed. Mean CVs were about 25% greater over ocean than over land, and, for land areas, were greatest at high latitude. The correlation between solar and wind anomalies was near zero in the global mean, but markedly positive or negative in some regions. Both wind and solar variability were correlated with values of climate modes such as the Southern Oscillation Index and Arctic Oscillation, with correlations in the Northern Hemisphere generally stronger during winter. We conclude that reanalysis solar and wind fields could be helpful in assessing variability in power generation due to interannual fluctuations in the wind and solar resource. Skillful prediction of these fluctuations seems to be possible, particularly for certain regions and seasons, given persistence or predictability of climate modes with which these fluctuations are associated.

This paper evaluates the potential of solar concentration technologies—compound parabolic collector (CPC), linear Fresnel collector (LFC) and parabolic trough collector (PTC)—as an alternative to conventional sources of energy for industrial processes in Latin America, where high levels of solar radiation and isolated areas without energy supply exist. The analysis is addressed from energy, economic and environmental perspective. A specific application for Argentina in which fourteen locations are analyzed is considered. Results show that solar concentration technologies can be an economically and environmentally viable alternative. Levelized cost of energy (LCOE) ranges between 2.5 and 16.9 c€/kWh/m² and greenhouse gas (GHG) emissions avoided range between 33 and 348 kgCO₂/(m²·year). CPC technology stands out as the most recommendable technology when the working fluid temperature ranges from 373K to 423K. As the working fluid temperature increases the differences between the LCOE values of the CPC and LFC technologies decrease. When 523K is reached LFC technology is the one which presents the lowest LCOE values for all analyzed sites, while the LCOE values of PTC technology are close to CPC technology values. Results show that solar concentration technologies have reached economic and environmental competitiveness levels under certain scenarios, mainly linked to solar resource available, thermal level requirements and solar technology cost.

This study investigates the mean annual water temperature trends at the confluence of the Sava and Danube Rivers, along with air temperature trends at the Belgrade meteorological station, spanning from 1956 to 2020. Results reveal a consistent increase in temperature across all three measuring stations, with the Danube experiencing a rise of 0.34°C/10 years, the Sava at 0.44°C/10 years, and Belgrade's air temperature increasing by 0.39°C/10 years. Employing the RAPS method, sharp rises in water temperature were pinpointed in 1989 for the Sava and 1990 for the Danube, while Belgrade's air temperature surge began in 1998. The highest intensity of air temperature increase within the recent period (1998-2020) was observed at the Belgrade observatory, reaching 0.76°C/10 years. Notably, the Sava exhibited a faster increase in water temperature over the last thirty years compared to the Danube. August marked the peak average water temperature for both rivers, while July recorded the highest average air temperature in Belgrade. Despite differing flow rates, both rivers exhibit similar hydrological regimes, with maximum flows occurring in April and minimum flows in August for the Sava, and October for the Danube. Seasonal temperature increases were most pronounced in summer, notably in August, with the smallest rises occurring during cold periods. Additionally, an inverse proportional relationship between mean annual water temperatures and discharges was observed at both river stations.

Effective solar forecasting has become a critical topic in the scholarly literature in recent years due to the rapid growth of photovoltaic energy production worldwide and the inherent variability of this source of energy. Due to the technological and econonomic limitations of energy storage solutions, using other, mosty conventional, sources to cover energy shortfalls and at the same time utilising solar surpluses production becomes necessary. The need to optimize energy systems, ensuring power continuity, and balancing energy supply and demand has led to the development of various forecasting methods and approaches based on meteorological data or photovoltaic plant characteristics. This article presents the results of a meta-review of the solar forecasting literature, including the current state of knowledge and methodological discussion. It presents a comprehensive set of forecasting methods, evaluates current classifications, and proposes a new synthetic typology. The article emphasizes the increasing role of artificial intelligence (AI) and machine learning (ML) techniques in improving forecast accuracy, alongside traditional statistical and physical models. It explores the challenges of hybrid and ensemble models, which combine multiple forecasting approaches to enhance performance. The paper addresses the emerging trends in solar forecasting research, such as the integration of big data and advanced computational tools. Additionally, from a methodological perspective, the article outlines a rigorous approach to the meta-review research procedure, addresses the scientific challenges associated with conducting bibliometric research, and highlights best practices and principles. This includes defining research questions, selecting eligibility criteria, literature search, data extraction, synthesis, and assessing bias and quality. The article contributes to the solar forecasting field by providing up-to-date knowledge, along with insights on the emerging trends, future research directions, and anticipating implications for the theory and practicce.

The transition region is a very thin but most peculiar layer in the solar atmosphere, located between the solar chromosphere and the corona. It is a key region for understanding the coronal heating, the solar eruptions triggering, and the origin of solar winds. Here, the gradients of all physical parameters are very high, including plasma density, ionization degree, temperature, and magnetic fields, etc. Therefore, the transition region should be highly dynamic, such as fast energy releasing and transporting, plasma heating, and even particle accelerating. They include two physical aspects: thermal and non-thermal processes. The thermal processes can be observed from the ultraviolet (UV) and extreme ultraviolet (EUV) emission by multi-wavelength images. The non-thermal processes, however, should be related to radio emissions especially at millimeter wavelengths, and the frequency range should span from several GHz to beyond 300 GHz, and the emission mechanism should be highly related to the magnetic fields and variations. The ultra-wide broadband spectral observations at millimeter wavelengths with high spectral resolutions may provide rich dynamic information about the transition region, such as non-thermal energy release and transmission, the flows of plasma and energetic particles, the magnetic fields and their variations, the generation and transportation of various waves, and the formation and evolution of the source regions of solar eruptions. Here, we discussed the spectral characteristics of millimeter-wave emission from the transition region and proposed a new conception of ultra-wide broadband millimeter-wave spectrometers to observe them.

In this study organic bulk heterojunction (BHJ) solar cell along with the spiro OMeTAD as a hole transport layer (HTL) and the PDINO as an electron transport layer (ETL) was simulated through the Solar Capacitance Simulator, one dimensional (SCAPS-1D) software to examine the performance of this type of polymer thin film organic solar cells. As an active layer the blend of polymer donor PBDB-T and non-fullerene acceptor ITIC-OE was used. Numerical simulation was performed by varying the thickness of HTL and active layer. Firstly, the HTL layer thickness was optimized to 50 nm, after that the active layer thickness varied up to 80 nm. These results of simulation demonstrated that the HTL thickness has rather little impact on efficiency while in the case of active layer thickness improves efficiency significantly. The temperature effect on the performance of solar cells was considered, by the simulation performed for temperature from 300 K up to 400 K and the efficiency of solar cell decreases with increasing temperature. Generally, polymer films usually are full of traps and defects, the density of defects (Nt) value was also introduced to the simulation, and it was confirmed that with the increasing of defect density (Nt), the efficiency of solar cell decreases. After thickness, temperature and defect density optimization, the reflection coating was also applied on it. It turned out that by introducing the reflection coating on the back side of solar cell, the efficiency increases by 2.5 %. Additionally, the positive effect of HTL and ETL doping on efficiency of this type of solar cells was demonstrated.

In this study, we discuss the thermospheric density response to the solar activity and QBO. By using the wavelet power spectrum method, the thermospheric density from 1967 to 2013 shows ~11-year period, semiannual and annual variations, while the seasonal variation is usually more significant under high solar activity conditions. Importantly, we investigate the possible link between the density and the QBO, with the aid of GAMDM model and different density residual method. As a result, the difference between the measured density and empirical model seemingly has QBO signal, but the ratio of them revels that the QBO signal does not exist in the thermospheric density. Comprehensively, we thought the stratospheric QBO cannot impact on the thermosphere, and more data and numerical modeling are needed for further validation.

Five fundamental problems—neutrino mass, baryogenesis, dark matter, inflation, strong CP problem—are solved at one stroke in a model, dubbed as “SM-A-S-H” (Standard Model-Axion-Seesaw-Higgs portal inflation) by Andreas Ringwald et. al. The Standard Model (SM) particle content is extended by three right-handed SM-singlet neutrinos $N_i$, a vector-like color triplet quark $Q$, a complex SM-singlet scalar field $\sigma$ that stabilises the Higgs potential, all of them being charged under Peccei-Quinn (PQ) $U(1)$ symmetry, the vacuum expectation value $v_\sigma\sim10^{11}$ GeV breaks the lepton number and the Peccei-Quinn symmetry simultaneously. We found that numerically SMASH model not only solves five fundamental problems but also the sixth problem “Vacuum Metastability” through the extended scalar sector and can predict approximately correct atmospheric neutrino mass splitting around 0.05 eV and the solar neutrino mass splitting around 0.009 eV.

In this study an adjusting post-processing approach is implemented for improving intra-hourly forecasts of solar power and ramp events of PV solar power systems at different locations in the United States. This study also serves as an out-of-sample test to evaluate the performance of the adjusting approach with different locations and timescales. Thus, various individual intra-hourly forecasts of solar power are combined and adjusted by applying the adjusting approach. Both point and probabilistic forecasts of solar power are included. After that, solar power ramp event forecasting by the adjusting approach is carried out.

This paper presents the results of the investigation of composite sinters W-TiB2 which were used as an electrode in the process of electro-spark deposition (ESD) and the examination of the deposited layers. The scope of the study includes detailed characteristics of powder mixtures, composite sinters made using the spark plasma sintering method (SPS) and layers deposited in the electro-spark process. The ESD process, using the W+30 vol.% TiB2 electrode, was carried out using an automated device. The substrates were made of copper and aluminium. The topography analysis of the surfaces of the composite layer and the evaluation of their wear resistance properties are also presented. The analysis of the results of research showed the possibility to obtain, using the SPS method, composite materials of good quality, which can be used as electrodes in the ESD process. The obtained layers had increased wear resistance in relation to the substrate material.

Astragalus is a very interesting plant genus well-known for content of flavonoids, triterpenes and polysaccharides. Its secondary metabolites are described as biologically active compounds showing a number of activities, like immunomodulating, antibacterial, antiviral and hepatoprotective. This inspired us to analyze the Bulgarian endemic A. aitosensis (Ivanisch.) to obtain deeper information about its phenolic components. We used extensive chromatographic separation of A. aitosensis extract to obtain seven phenolic compounds (1–7), which were identified using combined LC-MS and NMR spectral studies. The 1D and 2D NMR analysis and HR-MS allowed us to resolve the structures of known compounds 5–7 as isorhamnetin-3-O-robinobioside, isorhamnetin-3-O-(2,6-di-O-α-rhamno-pyranosyl-β-galactopyranoside), and alangiflavoside, respectively, and further comparison of these spectral data with available literature helped us with structural analysis of newly described flavonoid glycosides 1–4. These were described in plant source for the first time.

The objective of the present work is to investigate the performance of flat-plate solar panels in Greece that continuously follow the daily motion of the Sun. To that end, the annual energy sums are estimated on such surfaces from hourly solar horizontal radiation values at 43 locations covering all of Greece. The solar horizontal radiation values are embedded in the typical meteorological years of the sites obtained from the PV-GIS tool. All calculations use a near-real surface albedo; an isotropic and an anisotropic model are used to estimate the diffuse-inclined radiation. The analysis provides regression equations for the energy sums as a function of time (month, season). The annual energy sums are found to vary between 2247 kWhm−2 and 2878 kWhm−2 under all-sky conditions with the anisotropic transposition model. Finally, maps of Greece showing the distribution of the annual and seasonal solar energy sums under all- and clear-sky conditions are derived for the first time.

As the first initiative of its kind in Algeria, here is presented a solar-powered mobile “Ultraviolet Germicidal Irradiation” disinfection unit (UVGI) based on a special germicidal ultraviolet-C (UVC) radiator. The system was designed to disinfect several objects such as: medical tools, reusable masks, face-shields, gloves, phones, laptops, keys, money and many other portable devices that need to be disinfected/sterilized. It offers the advantage of complete autonomy through the built-in photovoltaic (PV) system that includes a solar panel, a gel battery, a charge controller and a power inverter. The system provides an extra 220V-50Hz outlet with 375VA maximum power to be used when energy is needed. The system is easily scalable to generate higher ultraviolet dosages by adding more UVC lamps. The chemical-free germicidal UVC sanitizing method employed by this device effectively disactivates a very wide range of microorganisms (microbes, bacteria and fungi and viruses including the actual SARS-CoV-2 that causes COVID-19 respiratory disease) and it has several advantages in comparison to chemical-based sanitizing methods. The total cost to make this open source device is below 1000 € and is easily customizable and scalable. This device is an open source, secure and fast equipment for objects and surface disinfection. The device will be fully automated by adding PIR sensors or remote control after further funding will be received.

Solar heating technology is a promising solution to promote China to achieve the “3060 double carbon” target as soon as possible. And seasonal thermal storage (STS) can effectively solve the mismatch problem of solar heating systems between the supply and demand of thermal energy. Due to the instability of solar radiation resources and heat demand, it is necessary to analyze the dynamic response characteristics of the system. Yet, related studies are still scarce. In this study, a solar heating system with a solar tower receiver and STS was introduced in north China. The dynamic performance of the system is analyzed with a dynamic simulated method in a typical day or typical operation modes, and the switch mechanism between multiple operation modes is also revealed. The impact of different heating strategies on system performance was analyzed. Results showed that the solar fraction of the system reached 89.4% in the third year, which was 3.6% higher than the first year. The quality-quantity heating operation strategies can be effective ways to improve the discharge efficiency of STS and the system performance without any heat pump. The electricity consumption of the pump on the heating side could be significantly reduced by 44.6% compared with the quality control.

This review paper explores the innovative realm of transparent solar panels, investigating their properties, applications, challenges, and recent advancements. Transparent solar panels, designed to harvest solar energy while allowing visible light to pass through, have gained significant attention due to their potential to revolutionize renewable energy technologies. The paper delves into the working mechanisms of various types of transparent solar panels, including Organic Photovoltaic (OPV) panels, Dye-Sensitized Solar Cells (DSSC), Perovskite Solar Cells, and Transparent Thin-Film Silicon Solar Cells. It discusses their integration into diverse applications, such as building-integrated photovoltaics, consumer electronics, the automotive industry, and aerospace. The review identifies challenges, including low efficiency, durability concerns, production costs, and integration hurdles, that currently hinder their widespread adoption. Moreover, the paper emphasizes the transformative potential of transparent solar panels in shaping the future of renewable energy, not only as energy generators but also as aesthetically pleasing and multifunctional components of our built environment. Finally, the paper underscores the need for continued research and development efforts to enhance efficiency, improve stability, and address integration challenges, paving the way for transparent solar panels to play a central role in the transition toward a more sustainable and energy-efficient future.

Despite a global push in the development and implementation of widespread alternative energy use, significant disparities exist across given nation-states. These disparities, frequently referred to as the local-national gap, reflect both technical and economic factors, as well as the social, political, and ecological gaps between how communities see energy development and national/global policy goals. This dataset is an attempt to bridge the local-national gap regarding solar PV adoption in the state of Georgia (U.S.A.). This dataset is an aggregation of variables from seven different publicly-available sources that was designed to help researchers interested in the context underlying solar adoption on the local scale of governance (e.g. the county level). The SolarView database includes information necessary for informing policymaking activities such as solar installation information, a historical county zip code directory, county-level census data, housing value indexes, renewable energy incentive totals, PV rooftop suitability percentages, and utility rates. As this is a database from multiple sources, incomplete data entries are noted.

The paper examines design and operating data of current concentrated solar power (CSP) solar tower (ST) plants. The study includes CSP with or without boost by combustion of natural gas (NG), and with or without thermal energy storage (TES). The latest, actual specific costs per installed capacity are very high, 6085 $/kW for Ivanpah Solar Electric Generating System (ISEGS) with no TES, and 9227 $/kW for Crescent Dunes with TES. The actual production of electricity is very low and much less than the expected. The actual capacity factors are 22% for ISEGS, despite combustion of a significant amount of NG largely exceeding the planned values, and 13% for Crescent Dunes. The design values were 33% and 52%. The study then reviews the proposed technology updates to produce better ratio of solar field power to electric power, better capacity factor, better matching of production and demand, lower plant’s cost, improved reliability and increased life span of plant’s components. The key areas of progress are found in materials and manufacturing processes, design of solar field and receiver, receiver and power block fluids, power cycle parameters, optimal management of daily and seasonal operation of the plant, new TES concepts, integration of solar plant with thermal desalination, integration of solar plant with combined cycle gas turbine (CCGT) installations and finally, specialization and regionalization of the project specification.

Taking a socio-technical perspective, I focus on solar businesses (niche market actors) in Iran. As one of the key stakeholder groups whose business prosperity is tied to the development of solar PV, they play a crucial role in accelerating the energy transition. Given the incumbent fossil-based electricity sector in Iran and the least enabling policies, I am first interested to find (i) the main drivers and barriers of solar businesses; and (ii) the roles these solar businesses play in bringing solar PV deployment forward in Iran. I collected the data via 20 semi-structured interviews with solar businesses in Golestan, Guilan, Tehran, Khorasan Razavi, and Eastern Azerbaijan Provinces in Iran. Taking an inductive approach, I considered sustainability transition and social acceptance theories as sensitising concepts to investigate common and specific points of solar business acceptance in Iran. I find ecological awareness, belief in intergenerational justice, and willingness to innovate, as the main intrinsic drivers and socioeconomic opportunity and tackling the energy imbalance as extrinsic drivers; while the lack of a common vision with the energy governors, and the low knowledge of solar PV among the customers, escalating prices, and challenges to accessing good quality solar equipment are the most prior obstacles. Moreover, I understand educating people, driving the innovative deployment of solar PV, and facilitating the diffusion of it, as the major roles of solar businesses in Iran. I find that the sustainability transition literature overlooked the key role of solar businesses specially in fossil-based and developing economies. My findings suggest that the positive intrinsic mechanisms among the solar businesses, in combination with better-enabling policy frameworks and external factors, like lifting the sanctions and joining the global energy market, climate change mitigation commitments and standards, can help solar businesspeople to lead and accelerate solar PV development in Iran.

The growing urgency for sustainable energy solutions necessitates a deeper understanding of the environmental impacts of renewable technologies. This article aims to synthesize and analyze Life Cycle Assessments (LCA) in this domain, providing a comprehensive perspective. We systematically categorize 2,923 articles into four communities: (1) Photovoltaic systems, (2) Wind energy systems, (3) Materials for auxiliary industry of photovoltaic and wind systems, and (4) Solar thermal systems. A comparative analysis is conducted to identify methodological consistencies and disparities across these communities. The findings reveal diverse methodological approaches and a range of environmental impacts, highlighting the complexities in assessing renewable energy systems. The article underscores the significance of material selection in photovoltaic and wind systems, providing a critical overview of the current state of LCA research in renewable energy and stressing the need for standardized methodologies. It also identifies gaps in recent research, offering insights for future studies focused on integrating environmental, economic, and social considerations in renewable energy assessments.As a case study, an LCA was used to evaluate two energy supply methods for a sensor network: one connected to the public grid and another powered by a photovoltaic panel. The off-grid system, while more environmentally friendly by reducing reliance on non-renewable energy sources, posed challenges due to the high environmental impact of battery production and disposal. Integrating environmental assessments provides a robust framework for making informed decisions on sustainable technologies. The findings are critical for projects that balance technological needs with sustainability goals.

As the cost of conventional energy continues to rise, and concerns over the environment grow, there is a growing interest in sustainable energy. It is believed that conventional energy will only last for around 50 years, making it essential to find a renewable energy source that is safe and feasible to replace fossil fuels. Solar energy is a superior alternative to conventional energy, as it is renewable and produces green energy that can be used directly. The maritime industry has found itself at the forefront of an evolving environmental consciousness, driven by the imperative to mitigate the carbon footprint left in the wake of ships. In this journey towards sustainability, solar energy has emerged as a beacon of hope, harnessing the boundless energy of the sun to wean vessels off their dependence on fossil fuels. Technological advancements have made solar power more accessible, and we can now see the use of solar panels on large ships and small crafts to reduce fuel usage and emissions. Solar panels are also increasingly used to power homes and businesses, and many countries are implementing policies to encourage their use. Solar energy is a key solution in reducing our dependence on non-renewable energy sources and combating climate change. However, the adoption of solar energy is but a stepping stone towards maritime sustainability, as the integration of CO2 capture, utilization, and storage (CCUS) technologies promises to amplify the industry's environmental impact to unprecedented heights.

The high environmental impact of conventional methods of cooling and heating has increased the need for renewable energy deployment for covering thermal loads. Towards that direction, the proposed system aims at offering an efficient solar powered alternative, coupling a zeolite-water adsorption chiller with a conventional vapor compression cycle. The system is designed to operate under intermittent heat supply of low-temperature solar thermal energy (<90 °C) provided by evacuated tube collectors. A prototype was developed and tested in cooling mode operation. The results of separate components testing showed that the adsorption chiller was operating efficiently, achieving a maximum coefficient of performance (COP) of 0.65. With respect to the combined performance of the system, evaluated on a typical week of summer in Athens, the maximum reported COP was approximately 0.575, mainly due to the lower driving temperatures at a range of 75 °C. The corresponding mean energy efficiency ratio (EER) obtained was 5.8.

Photovoltaic is one of the promising renewable sources of power to meet the future challenge of energy need. Organic and perovskite thin film solar cells are an emerging cost-effective photovoltaic technology because of low-cost manufacturing processing and a light-weight. The main barrier of commercial use of organic and perovskite solar cells is the poor stability of devices. Encapsulation of these photovoltaic devices is one of the best ways to address this stability issue and enhance the device lifetime by employing materials and structures that possess high barrier performance for oxygen and moisture. The aim of this review paper is to find different encapsulation materials and techniques for perovskite and organic solar cells according to the present understanding of reliability issues. It discusses the available encapsulate materials and their utility in limiting chemicals such as water vapour, oxygen penetration. It also covers the mechanisms of mechanical degradation within the individual layers and solar cell as a whole, and possible obstacles to their application in both organic and perovskite solar cells. The contemporary understanding of these degradation mechanisms, their interplay and their initiating factors (both internal and external) are also discussed.

Research Highlights: Data of advanced-age provenance tests were reanalyzed applying a new approach, to directly estimate the growth of populations at their original sites under individually generated future climates. The results reveal surprisingly high resilience potential of fir species. Background and Objectives: The growth and survival of silver fir under future climatic scenarios is insufficiently investigated at the xeric limits. The selective signature of past climate determining the current and projected growth was investigated to analyze the prospects of adaptive silviculture and assisted transfer of silver fir populations, and of the introduction of non-autochthonous species. Materials and Methods: Hargreaves’ climatic moisture deficit was selected to model height responses of adult populations. Climatic transfer distance was used to assess the relative drought stress of populations at the test site, relating these to the past conditions to which the populations had adapted. ClimateEU and ClimateWNA pathway RCP8.5 data served to determine individually past, current, and future moisture deficit conditions. Beside silver fir, other fir species from South Europe and the American Northwest were also tested. Results: Drought tolerance profiles explained the responses of transferred provenances and predicted their future performance and survival. Silver fir displayed significant within-species differentiation regarding drought stress response. Applying the assumed drought tolerance limit of 100mm relative moisture deficit, most of the tested silver fir populations seem to survive their projected climate at their origin until the end of the century. Survival is likely also for transferred Balkan fir species and for grand fir populations, but not for the Mediterranean species. Conclusions: The projections are less dramatic than provided by usual field assessments. Some results contradict generally accepted concepts. The method fills the existing gap between experimentally determined adaptive response and the predictions needed for management decisions. It also underscores the unique potential of provenance tests.

Solar cosmic rays (SCR) are generated during the primordial energy release in solar flares. This explosive process takes place in the solar corona above the active region. It represents fast release of the magnetic field energy of the current sheet, which is formed near a singular magnetic field line. Solar cosmic rays appear as a result of acceleration of charged particles, mainly protons, by an inductive electric field in the current sheet, equal to the field E=V´B/c near the current sheet. To study the mechanism of solar flares and obtain conditions for stydy SCR acceleration it is necessary to carry out magnetohydrodynamic (MHD) simulation of a flare situation in the solar corona above a real active region. The methods of stabilization were developed which made it possible to solve partially the problem of numerical instabilities. MHD simulations showed complicated configuration near the singular line. Comparison of the results of MHD simulations with observations showed a general agreement of the positions of the current sheets with regions of intense flare radiation. However, there are some problems with the details of such coincidences. The results show the possibility of improving the methods of MHD simulation in order to solve the arisen problems.

The coupled Dirac equations for solar e- and μ-neutrinos are solved in the presence of a small uniform interaction of the e-neutrinos with matter (the Sun). It is shown that the interaction leads to an increase of the amplitude of the neutrinos oscillations and a decrease of the lo- calization probability of the e-neutrinos. However, the strength of this interaction is insufficient to explain the magnitude of the discrepancy between the solar neutrino flux and the neutrino flux measured on the Earth. An alternative interpretation related to a possible superfluid neutrino state is advanced, which may throw some light on the solar neutrino problem.

Solar geoengineering (SG) solutions have many advantages compared to the difficulty of carbon removal (CR): SG produces fast results, is shown here to have much higher efficiency than CR, is not related to fossil fuel legislation, and is something we all can participate in brightening the Earth with cool roofs, and roads. SG requirements detailed previously to mitigate global warming (GW) have been concerning primarily because of overwhelming goals and climate circulation issues. In this paper, the advantages of annual solar geoengineering (ASG) to mitigate yearly global warming increases are explored and detailed as it provides higher feasibility in geoengineering applications. ASG area modification requirements found here are generally 50 to possibly higher than 150 times less compared to the challenge of full SG GW mitigation reducing circulation concerns. Results indicate that there are mixed technologies that can help meet annual mitigation Earth brightening goals. As well, results show much higher feasibility for L1 space shading compared to prior literature estimates for full GW mitigation. However, stratosphere injections appear challenging in the annual approach. Because ASG earth brightening area requirements are much smaller than those required for full mitigation, we have concerns that worldwide negative SG would interfere with making positive advances for several reasons. Negative SG currently dominates yearly practices with the application of dark asphalt roads and roofs. This issue is discussed.

One of the key areas of the International Renewable Energy Agency’s (IRENA) programme of work is the analysis of renewable technology costs and performance and the dissemination of these results to as wide an audience as possible. In addition to analysis, IRENA seeks to engage a broad range of stakeholders in the context of this work through the Renewable Costing Alliance. The Costing Alliance brings together companies, industry association, governments and researchers to share, confidentially, data for real-world renewable energy project cost and performance, helping to build further on IRENA’s costing work to date. In this context the authors analyse the current cost differentials and cost reduction potentials for solar PV in Japan compared to best practice levels and identify the reasons for higher costs in Japan and how to reduce them. This study analyses the current installed cost differentials for utility-scale, commercial and residential rooftop solar PV systems. In addition to identifying the reasons for the cost differentials, potential policy recommendations to reduce the cost differential are identified.

Solar neutrinos have played a central role in the discovery of the neutrino oscillation mechanism. They still are proving to be a unique tool to help investigate the fusion reactions that power stars and further probe basic neutrino properties. The Borexino neutrino observatory has been operationally acquiring data at Laboratori Nazionali del Gran Sasso in Italy since 2007. Its main goal is the real-time study of low energy neutrinos (solar or originated elsewhere, such as geo-neutrinos). The latest analysis of experimental data, taken during the so-called Borexino Phase-II (2011-present), will be showcased in this talk - yielding new high-precision, simultaneous wide band flux measurements of the four main solar neutrino components belonging to the "pp" fusion chain (pp, pep, ⁷Be, ⁸B), as well as upper limits on the remaining two solar neutrino fluxes (CNO and hep).

The evolution of photovoltaic cells is intrinsically linked to advancements in the materials from which they are fabricated. This review paper provides an in-depth analysis of the latest developments in silicon-based, organic, and perovskite solar cells, which are at the forefront of photovoltaic research. We scrutinize the unique characteristics, advantages, and limitations of each material class, emphasizing their contributions to efficiency, stability, and commercial viability. Silicon-based cells are explored for their enduring relevance and recent innovations in crystalline structures. Organic photovoltaic cells are examined for their flexibility and potential for low-cost production, while perovskites are highlighted for their remarkable efficiency gains and ease of fabrication. The paper also addresses the challenges of material stability, scalability, and environmental impact, offering a balanced perspective on the current state and future potential of these material technologies.

The energy transition to wind and solar opens opportunities for green hydrogen as the wind and solar generation tends to bring electricity prices down to very low levels. This paper evaluates whether green hydrogen can integrate well with wind and solar PV to help with improved management of the South Australian electricity grid. Green hydrogen can use membrane electrolysis plants during surplus renewable energy periods. This hydrogen can then be electrified or used in industry. The green hydrogen system was analysed to understand the financial viability and technical impact of integrating green hydrogen. We also used systems engineering techniques to understand the system holistically, including the technical, social, environmental, and economic impacts. The results show opportunities for the system to provide seasonal storage, grid firming, and reliability services. Financially, it would need changes to electricity rules to be viable, but without those changes, our modelling suggested it would be financially viable within this decade

This paper studies pandemic viruses that spread during the period (1759–2020) according to solar activity cycles. Our findings and results include the following: (1) The severity of a pandemic correlates negatively with the strength of solar activity; (2) Pandemic viruses are classified into three types based on their compatibility with solar activity associations. Most of them spread through the quiet Sun, where viruses survive better in cold and rainy weather, and in stable geomagnetic fields without strong disturbances; (3) The emergence of new strains of influenza viruses was manifested in two ways. First, the annual epidemics due to antigenic drift. Second, pandemics recur every 1–12 solar cycles (about 11–120 years) due to viral reassortment of new subtypes, which results in antigenic shifts; (4) Pandemic viruses have two groups according to their recurring period: first, recurring in nine solar cycles; second, recurring in twelve solar cycles. Furthermore, we reassort pandemic viruses from their previous spread in the same periodic classification. Moreover, we derive a periodicity formula for each subtype of the pandemic virus as a spread date.

This paper is regarding design and program an Micro-controller Arduino Uno board by using Arduino software to work as a photo-sensor(Active) single axial solar tracker system(SASTS). A solar panel, two photo-resistors (LDR) in two sides (north/south) of the photo-voltaic(PV) and a servo motor are connected to the Uno board, which is running a code that prepared by Arduino software IDE in advanced then it works as a tracking system. Here, the LDRs send the signal of presence or absence of the light to the board and based on that sent signal the Uno reflects a new signal to the servo motor to rotate and finds the light source. Lastly, the photo-sensor single axis tracker is made while Continuously, the system tries to face the panel to the sun and whilst changing the irradiance intensity it starts searching to find the angle of highest irradiance. Based on results that are extracted from the data, the tracker system significantly boosts the output efficiency of the solar panel. By using the Micro-controller Uno board, LDRs, servo motor and special designed mechanical base, the tracking system is constructed, based on acquired data the influence of the STS on the increasing the solar panel efficiency is more obvious. Significantly, the tracker system rises the efficiency of the PV .

In the past two decades the world experienced an exceptional number of unprecedented extreme weather events, some causing major human suffering and economic damage, such as the March 2012 heat event, which was called “Meteorological March Madness.” From the beginning of space era a correlation of solar flares with pressure changes in atmosphere within 2–3 days or even less was reported. In this study we wanted to test the possible relation of highly warm weather events in North-East America with Solar Energetic Particle (SEP) events. For this reason we compared ground temperatures T_M in Madison, Wisconsin, with energetic particle fluxes P measured by the EPAM instrument onboard the ACE spacecraft. In particular, we elaborated case events and the results of a statistical study of the SEP events related with the largest (Dst ≤ −150nT) Coronal Mass Ejection (CME)-induced geomagnetic storms, between with the years 1997–2015. The most striking result of our statistical analysis is a very significant positive correlation between the highest temperature increase_. ΔT_M and the time duration of the temperature increase ΔT_M (r = 0.8, p <0.001) at “winter times” ( r = 0.5, p , 0.01 for the whole sample of 26 SEP examined events). The time response of T_M to P was found to be in general short (a few days), but in the case of March 2015, during a gradual P8 increase, a cross-correlation test indicated highest c.c. within 1 day (p < 0.05). The March 2012 “meteorological anomaly” was elaborated in the case of South-East Europe, where, beside a period of strong winds and rainfall (6-13.3.2012), intense precipitation in North-East Greece (Alexandroupoli) were found to be correlated with distinct high energy flux enhancements. A rough theoretical interpretation is discussed for the space—atmospheric extreme weather relationship we found. However, much work should be done to achieve early warning of space weather dependent extreme meteorological events. Such future advances in understanding the relationships between space weather and extreme atmospheric events would improve atmospheric models and help people’s safety, health and life.

Anderson – Fabry disease (AFD) is a rare, X-linked lysosomal storage disorder caused by a mutation in the α-Galactosidase A gene resulting in α-Galactosidase A enzyme (α-Gal A) deficiency. The metabolic defect leads to progressive accumulation of glycosphingolipids and structural and functional impairment of affected organs. Due to the inheritance pattern, male patients are hemizygous with more severe manifestations of the disease as compared to females who in most cases are heterozygous with delayed and variable clinical presentation caused by uneven X – chromosome inactivation. Fabry disease cases are often identified by targeted screening programs in high-risk groups, such as in patients with end-stage renal disease, premature stroke or unexplained cardiomyopathy. Here we describe a unique case of homozygous female patient identified by a nationwide screening program in hypertrophic cardiomyopathy patients. Before the systematic screening, the patient had a diagnosis of hypertrophic obstructive cardiomyopathy and was treated accordingly including alcohol septal ablation to reduce the obstructive gradient. The confirmation of Fabry disease has led to discovery of the same variant in several members of her family. The identified variant was c.644A>G, p.Asn215Ser (N2015S) known to cause predominant cardiac involvement with late onset of the disease. The variant is amenable for an oral therapy by the small molecular chaperone migalastat which was started, then interrupted for recurrence of patient´s migraine and then re-initiated again after two years. During this period the patient received enzyme replacement therapy by agalsidase beta but developed a progressively worsening venous access. Our case illustrates the importance of systematic screening of patients with clinical evidence of hypertrophic cardiomyopathy in whom routine diagnostic process fails to discover Fabry disease, in particular variants with late onset cardiac manifestations. Many of the late onset variants are amenable for orally active therapy by migalastat which significantly improves the comfort of the treatment. Its long term results are analysed by a large international “Follow-me” registry which was designed to verify the validity of pivotal trials with migalastat in Fabry disease.

Despite a global push in the development and implementation of widespread alternative energy use, significant disparities exist across given nation-states. These disparities reflect both technical and economic factors, as well as the social, political, and ecological gaps between how communities see energy development and national/global policy goals. Known as the “local-national gap,” many nations struggle with fostering meaningful conversations about the role of alternative energy technologies within communities. Mitigation of this problem first requires understanding the distribution of existing alternative energy technologies at the local level of policymaking. Using the State of Georgia, U.S.A. as a case study, we present a model for analyzing how existing adoption trends enable/limit conversation at the scale of local governance (i.e., county governments). Leveraging existing work on the Gini Coefficient as a metric for measuring energy inequity, we argue these tools can be applied to analyze where gaps exist in ongoing solar adoption trends. As we demonstrate, communities that adopt solar tend to be concentrated in a few counties, indicating existing conversations are limited to a circumscribed set of social networks. This information and the model we demonstrate can enable focused qualitative analyses of existing solar trends, not only amongst high-adoption areas but within communities where little to no adoption has occurred.

Membrane gas absorption technology and solar-assisted regeneration system are two promising approaches to reduce high energy consumption associated with carbon dioxide capture from coal fired power plants. In the present study, a solar-assisted hollow fiber membrane contactor (SOL-HFMC) power plant is proposed to capture and desorb CO₂ in hollow fiber membrane contactors with the assistance of solar thermal collectors. Techno-economic assessment and sensitivity analysis of the proposed system is carried out in three studied locations with different weather conditions for a 580 MWe pulverized coal power plant. Research results show that, the output capacity and net efficiency of the SOL-HFMC power plant are significantly higher than those of the reference power plant regardless whether TES system is applied or not. In addition, CEI of the SOL-HFMC power plant with TES system is 4.36 kg CO₂/MWh, 4.45 kg CO₂/MWh and 4.66 kg CO₂/MWh lower than that of the reference power plant. The prices of membrane, vacuum tube collector and phase change material should be reduced to achieve lower LCOE and COR values. Specifically for SOL-HFMC power plant with TES system, the corresponding vacuum tube collector price shall be lower than 25.70 $/m² for Jinan, 95.20 $/m² for Xining, and 128.70 $/m² for Lhasa, respectively. To be more competitive than solar-assisted ammonia-based post-combustion CO₂ capture power plant, the membrane price in Jinan, Xining and Lhasa shall be reduced to 0.012 $/m, 0.015 $/m and 0.016 $/m for the sake of LCOE, and 0.03 $/m, 0.033 $/m and 0.034 $/m for the sake of COR, respectively. The findings can provide guidance for decision-making and risk management strategies.

This paper provides a study on the development of solar energy, its prospects, and its impacts in Africa. Although the main focus is on technologies adopted for different uses (solar farms, mini-grids, off-grid, solar houses, irrigation, lighting, etc.), we also consider some aspects that increase the adoption of solar energy, such as legislation and business models. Finally, we will examine current and future solar projects managed by NGOs and international companies and how they benefit to leveraging social and economic standards, quality of life as well as capacity building in Africa. This study shows the plethoric interest of institutions outside Africa in the market of solar energy in the continent and that there is no African strategy to increase its independency toward a sustainable development particularly through energy transition.

The prohibitive costs of small-scale solar photovoltaic (PV) racks decreases PV adoption velocity. To overcome these costs challenges, an open hardware design method is used to develop two novel variable tilt racking designs. These are the first stilt mounted racking designs that allow manual change of tilt angle from zero to 90 degrees by varying the length of cables. The racks are designed using the calculated dead, wind and snow loads for Canada as conservative design for most of the rest of the world. Structural capacities of the wooden members are then ascertained and resisting bending moment, shear force, tensile force, and compressive force for them is calculated. A structural and truss analysis is performed to ensure that racking design with-stands the applicable forces. Moreover, implications of changing the tilt angle on the wooden members/cables used to build the system are also determined. The systems offer significant economic savings ranging from 1/3rd to 2/3rd the capital expenses of the commercially available alternatives. In addition, the racking designs are easy-to-build and require minimal manufacturing operations, which increases their accessibility. The stilt-mounted designs can be employed for agrivoltaic settings while allowing farm workers shaded ergonomic access to perform planting, weeding, and harvesting.

Multi-junction solar cells comprised of stacked III-V semiconductor junctions represent the highest-efficiency photovoltaic technology, with recent demonstrations exceeding 47% efficiency . Optimizing the design and thickness of each junction is critical for maximizing performance . This work utilizes Silvaco TCAD tools to systematically optimize a 5-junction cell based on AlInP, AlGaInP, AlGaInAs, GaInP, GaAs, InGaAs, and Ge similar to recent record cells . The junction thicknesses are varied using a predictive profiler to sample the parameter space . For each combination, the spectral absorption and I-V characteristics are simulated to determine the efficiency . Statistical analysis identifies the optimal thickness set that maximizes performance to 26% under 1 sun illumination .

In this paper, solar irradiance and wind speed forecasts were performed considering time horizons ranging from 10 min to 60 min, under a 10 min time-step. Global horizontal irradiance (GHI) and wind speed were computed using four forecasting models (Random Forest, k-Nearest Neighbours, Support Vector Regression, and Elastic Net) to compare their performance against two alternative dynamic ensemble methods (windowing and arbitrating). Forecasting models and dynamic forecasting ensembles were implemented in Python for performance evaluation. The performance comparison between the prediction models and the dynamic ensemble methods was carried out by evaluating the RMSE, MAE, R² and MAPE, to evaluate whether the dynamic ensemble forecasting method obtained greater. According to the results obtained windowing dynamic ensemble method was the most efficient among the tested. For the wind speed data, by varying its parameter λ (from 1 to 100), a variable performance profile was obtained, where from λ =1 to λ = 74, windowing proved to be the most efficient, reaching maximum efficiency for λ = 19. Windowing was the best method for the GHI analysis, reaching its best performance for λ = 1. The efficiency gain using windowing was 0.56% when using the wind speed model and 1.96% for GHI.

The recent happenings in the world such as flood and wild forest fire were as a result of climate effect as being envisaged by scientists. It is urgent now to adopt a source of energy that will eliminate this effect on our universe. Solar energy is the major energy means that is abundant which could be utilized. In this review, the prospects of solar energy exploration were studied in Nigeria which include assessments, economic viability and hybrid systems. Findings show higher potential in the North as compared to the Southern region. Additionally, potential of offshore solar energy system was simulated by considering 2002, 2003 and 2004 data sets from Era5-land base. Their monthly mean, seasonal changes and annual mean value were estimated. The algebraic annual solar radiance for 2002, 2003 and 2004 were 34,914.732 kWh/m2, 33,898.316 kWh/m2 and 34,338.324 kWh/m2. Suggestions were made due to the present status of solar energy utilization that will enhance its maximum usage and development. One of these is the establishment of a functioning financial scheme and the database for all renewable energy systems. When all these are put in place, the energy supply will increase, climate effect will be reduced, and the economy will be boosted.

Electric energy is one of the driving forces in every country. The supply of electrical energy continues to present various challenges, such as high costs associated with procuring raw materials for generation, sparsely populated areas that are not connected to the main grid, and the need for infrastructure to support generation and network delivery. These challenges have contributed to the growing adoption of renewable energy sources, particularly solar photovoltaics (PV).In this study, we have developed a practical method to assess the spatial PV potential in a selected urban area. The methodology combines data collected from an unmanned aerial vehicle (UAV) photogrammetry, Geographic Information System (GIS), and the energy output from three remote photovoltaic systems installed at different locations. The results obtained from this approach not only provide the energy generated per square meter, per year (kWh m-2 yr-1), but also provides a base to calculate the potential distance that electric cars could travel based on the energy generated. To illustrate the application of this method, two practical cases were selected: Senglea, Malta, and Munxar, Gozo. These examples highlight the versatility and effectiveness of our approach for evaluating and harnessing solar energy through photovoltaic panels in different contexts.

Salinity acts as a critical environmental filter on microbial communities in natural systems, negatively affecting microbial diversity. However, how salinity affects the community assembly remains unclear. This study used Wendeng multi-pond saltern as a model to evaluate the prokaryotic community composition and diversity and quantify the relative importance of ecological processes across salinity gradients. Results showed that low saline salterns (45-80 g/L) exhibited higher bacterial diversity than those in high saline salterns (175-265 g/L). The relative abundance of taxa assigned to Halanaerobiaceae, Haloferacaceae, Desulfohalobiaceae, Phormidiaceae, Rohodobacteraceae, and Nitrococcaceae was higher with increasing salinity. Salinity and pH were the primary environmental factors that directly or indirectly determined the composition and diversity of prokaryotic communities. Microbial co-occurrence network dynamics were more complex in the sediment than in water of salterns. An infer Community Assembly Mechanisms by Phylogenetic-bin-based null model analysis (iCAMP) showed that microbial community assembly in sediment and water differed. Our findings provide more information about microbial community structure and the importance of various ecological processes in controlling microbial community diversity and succession along salinity gradients in water and sediment environments.

Molecular mechanisms for N2 fixation (solar NH3) and CO2 conversion to C2+ products in enzymatic conversion (Nitrogenase), electrocatalysis, metal-complexes and plasma-catalysis are analysed and compared. It is evidenced that differently from what present in thermal and plasma-catalysis, the electrocatalysis path requires not only the direct coordination and hydrogenation of undissociated N2 molecule, but to realize a series of features present in the Nitrogenase mechanism. There is the need of i) a multi-electron and -proton simultaneous transfer, not as sequential steps, ii) forming bridging metal hydride species, iii) generate intermediates stabilized by bridging multiple metal atoms, iv) have the capability of the same sites to be effective both in N2 fixation and in COx reduction to C2+ products. Only iron oxide/hydroxide stabilized at defective sites of nanocarbons was found to have these features. This comparison of the molecular mechanisms in solar NH3 production and relations with CO2 reduction is proposed to be a source of inspiration to develop the next generation electrocatalysts to address the challenging transition to a future sustainable energy and chemistry beyond fossil fuels.

Space vehicles may be propelled by solar sails exploiting the radiation pressure coming from the sun and applied on their surfaces. This work deals with the adoption of Shape-Memory Alloy (SMA) elements in the sail deployment mechanism activated by the Joule Effect, i.e. using the same SMA elements as a resistance within suitable designed electrical circuits. Mathematical models were analyzed for the thermal analysis by implementing algorithms for the evaluation of the temperature trend depending on the design parameters. Several solar sail prototypes were built up and tested with different number, size and arrangement of the SMA elements, as well as the type of the selected electrical circuit. The main parameters have been discussed in the tested configurations and advantages discussed as well.