To obtain drop-in fuel properties from non-feed biomass, we herein report the catalytic hydrotreatment of microalgae biocrude, produced from hydrothermal liquefaction (HTL) of Spirulina. Our contribution focuses on the effect of temperature, initial H2 pressure, and residence time on the removal of heteroatoms (O and N). In contrast to common hydrotreating experimental protocols at batch scale, we devised a set of two-level factorial experiments and studied the most influential parameters affecting the removal of heteroatoms. It was found that up to 350 °C, the degree of deoxygenation (de-O) is mainly driven by temperature, whereas the degree of denitrogenation (de-N) also relies on initial H2 pressure and temperature-pressure interaction.Based on this, complete deoxygenation was obtained at mild operating conditions (350 °C), reaching a concurrent 47 % denitrogenation. Moreover, three optimized experiments are reported with 100 % removal of oxygen. In addition, the analysis by GC-MS and Sim-Dis gives insight to the fuel quality. The distribution of heteroatom N in lower (<340 °C) and higher (>340 °C) fractional cuts is studied by a fractional distillation unit following ASTM D-1160. Final results show that 63-68 % of nitrogen is concentrated in higher fractional cuts.

Prevalence of malnutrition among children under five is alarmingly high in Pakistan. However, there are ready-to-use therapeutic foods (RUTF) available which may be used to treat children with severe acute malnutrition (SAM). This study aims to assess the efficacy of prebiotics as a synergistic additive to RUTF to enhance blood parameters and anthropometric measurements in children with uncomplicated SAM living in Southern Punjab, Pakistan. A double-blind parallel treatment randomized controlled trial was conducted on 204 children aged between 6-59 months. Participants were randomized and allocated to the placebo (n=102) and experimental arms (n=102) at a 1:1 ratio. One group of children were provided RUTF and 4 g prebiotics, while the other group were given RUTF and starch as a placebo. Participants recruited for both arms were given treatment for eight weeks, and then their biochemical and anthropometric outcomes were evaluated. A substantial difference between the mean weight, mid upper arm circumference, haemoglobin, haematocrit, platelet count, mean corpuscular volume, mean corpuscular haemoglobin, and albumin was revealed. Conclusively, supplementation with RUTF and prebiotics has proven to be an efficient, effective and safe therapy for children suffering from SAM to improve their growth and development indicators and reduce the dangers of malnutrition in comparison to RUTF alone.

For a considerable length of time synthetic composts are utilized to satisfy the dirt necessity of supplements and yield, however huge measure of these substance manures are hazardous for condition, advantageous microorganisms, creatures, and people also. In this way, natural inviting and savvy biofertilizers are utilized. Biofertilizer are the substances which contain microorganisms those microorganisms might be growths, microscopic organisms, and protozoa which have capacity to build ripeness of soil by Nitrogen obsession, Phosphorous solubilization, and Iron sequestration. These cycles convert insoluble type of supplements into solvent structure and make it accessible to the foundations of plant which effectively take them up and use them. There are assortment of the yields whose profitability can be expanded by applying biofertilizer, for example, rice, oat, and other grain crops. In this audit we experience the method of utilization of biofertilizers, and how the assistance the plants and in which they help.

Applications for Wireless Sensor Networks (WSNs) range from monitoring the environment to automating factories. However, sustained and effective functioning is made more difficult by Sensor Nodes (SNs) limited energy supplies in which optimization is the main issue. So with the aim of increasing the lifespan by decreasing the energy consumption of WSN, Low-Energy Adaptive Clustering Hierarchy (LEACH) protocol with Deep Learning (DL) algorithm is analyzed in this paper. LEACH is a hierarchical mechanism that elects Cluster Heads (CHs) and regularly rotates their positions in order to allocate energy use effectively by using the same amount of energy. However, Deep Learning (DL) method is used to further improve energy optimization. In many applications, the types of Deep Learning methods like Artificial Neural Networks (ANNs) have shown to be very useful. Using this method, WSNs may make more efficient decisions that reduce energy consumption. Data aggregation, duty cycling, and transmission protocols may all be optimized by Deep Learning model's ability to recognize patterns and forecast network behavior. This results in lower energy consumption, a longer lifespan for the network, and better overall performance.

A case report of the diagnosis of Long Term Sequelae of West Nile Neuroinvasive Disease in a patient with 9 years history. Empirical data of symptoms and test reports has been presented and based on the available data likely pathogenesis of the disease has been discussed. The empirical data has been compared to the published literature to reach a highly confident diagnosis.

Proteins possess complex three-dimensional structures, and these structures are stable only within specific ranges of temperature which mostly correspond to the temperature ranges of the host organisms. However, few exceptional proteins, called heat-stable proteins, are stable at temperatures that are substantially higher than those tolerated by the host organisms themselves. Most of the heat-stable proteins possess heat stability to perform their functions at high temperatures, but some of them are intrinsically heat-stable due to their structure. Heat-stable proteins are usually divided into three or four groups depending upon the intricacies of their structures and thermal behaviors. Their peculiar property, i.e. heat-stability, makes them very valuable in applications such as polymerase chain reaction, industrial processes requiring high temperature, and protein engineering. Heat-stability also makes it feasible to purify such proteins, from the rest of the heat-labile proteins, using a simple heat-treatment method. Moreover, heat treatment can be used as a combined cell-lysis and protein purification step which, as compared to conventional methods, can result in a higher yield of heat-stable proteins. Furthermore, some special heat-stable proteins, i.e. intrinsically disordered proteins (which include the proteins involved in important neurodegenerative diseases), need heat-treatment step, in some cases, as the only way for their successful purification and study. Hence, this paper provides a first-ever comprehensive review of all major aspects of heat-stable proteins, i.e., their structure, evolution, classification, significance, and heat-treatment mediated purification.

Coronavirus that is also known as COVID-19 disease is produced by SARSCoV-2. This causative agent is highly contagious and can cause potentially fatal pneumonia worldwide with serious public health concerns. In the beginning among infected individuals, most of them were those who were mainly shown to the wet animal market in a big city of China known as Wuhan. So, it was suggested that this was almost certainly the zoonotic source of COVID-19illness. The transitional source of origin and their mode of transmission to humans were not known obviously. Conversely, from human to human rapidly transformation have been confirmed generally. Currently, there is no availability of FDA approved clinically antiviral drugs and/or vaccines to be used against the COVID-19. Afterward, SARS-CoV and MERS-CoV, the occurrence of SARS-CoV-2 has been manifested as the third sketch of an enormously pathogenic coronavirus into human population globally. In this review, we provide a brief overview of the history of COVID-19 in Pakistan up-to 18^th weeks after beginning, current situation, epidemiology, and its impact on the human population. Moreover, we focused on physiological variation during the incubation period, genome analysis of SARS-CoV2, supportive treatment approaches, and safety measures in the Pakistani population, which may be supportive for combating the risk of COVID-19 epidemic. We also reviewed the future approaches for the development of therapeutic interventions and vaccines to cope with the COVID-19 epidemic.

In this paper, we discuss voltage control method for buck converter operating in continuous conduction mode (CCM) using analog feedback system. The aim of this work is to control the output voltage of a buck converter during the variation in load current. This is obtained using analog feedback made with operational amplifier (Opamp). However, the same technique can be applied to other DC-DC converters (e.g boost, buck-boost, cuk converter, etc) in CCM mode, but for the purpose of analysis buck converter is chosen as an example.

Lamb wave-based structural health monitoring is widely acknowledged as a reliable 11 method for damage identification, classification, localization and quantification. However, due to 12 the complexity of Lamb wave signals, especially after interacting with structural components and 13 defects, interpreting these waves and extracting useful information about the structure's health is 14 still a major challenge. However, deep learning-based strategy offers a great opportunity to address 15 such challenges as the algorithm can operate directly on raw discrete time-domain signals. Unlike 16 traditional methods, which often require careful feature engineering and preprocessing, deep learn-17 ing can automatically extract relevant features from the raw data. This paper proposes an autoen-18 coder based on a bidirectional long short-term memory network with maximal overlap discrete 19 wavelet transform layer to detect the signal anomaly and determine the location of the damage in 20 the composite structure. This approach has the potential to greatly enhance our ability to detect and 21 locate structural damage in composite structures, thereby increasing safety and efficiency.

Biomedical implants are the need of this era due to the increase in number of accidents and follow-up surgeries. Different types of bone diseases such as osteoarthritis, osteomalacia, bone cancer, etc. are increasing globally. Mesoporous bioactive glass nanoparticles (MBGNs) are used in biomedical devices due to their osteointegration and bioactive properties. In this study, silver (Ag) and strontium (Sr) doped mesoporous bioactive glass nanoparticles (Ag-Sr MBGNs) were prepared by a modified Stöber process. In this method, Ag+ & Sr2+ were co-substituted in pure MBGNs to harvest the antibacterial properties of Ag ions, as well as pro-osteogenic potential of Sr2 ions. The effect of the two ion concentration on morphology, surface charge, composition, antibacterial ability, and in-vitro bioactivity was studied. Scanning electron microscopy (SEM), X-Ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) confirmed the doping of Sr and Ag in MBGNs. SEM and EDX analysis confirmed the spherical morphology and typical composition of MBGNs, respectively. The Ag-Sr MBGNs showed a strong antibacterial effect against Staphylococcus carnosus and Escherichia coli bacteria determined via turbidity and disc diffusion method. Moreover, the synthesized Ag-Sr MBGNs develop apatite-like crystals upon immersion in simulated body fluid (SBF), which suggested that the addition of Sr improved in-vitro bioactivity. The Ag-Sr MBGNs synthesize in this study can be used for the preparation of scaffolds or as a filler material in the composite coatings for bone tissue engineering.

Copper indium gallium selenide (CIGS) is an inexpensive material that has the potential to dominate the next-generation photovoltaic (PV) industry. Here we detail computational investigation of CIGS solar cell with encouragement of adopting cuprous dioxide (Cu₂O) as a Hole Transport Layer (HTL) for efficient fabricated CIGS solar cells. Although Cu₂O as a HTL has been studied earlier for perovskite and other organic/inorganic solar cell yet no study has been detailed on potential application of Cu₂O for CIGS solar cells. With the proposed architecture, recombination losses are fairly reduced at the back contact and contribute to enhanced photo-current generation. With the introduction of Cu₂O, the overall cell efficiency is increased to 26.63%. The wide-band of Cu₂O pulls holes from the CIGS absorber which allows smoother extraction of holes with experiencing lesser resistance. Further, it was also inferred that, HTL also improves the quantum efficiency (QE) for photons with large wavelengths thus increases the cell operating spectrum.

Pakistan relies mostly on fossil fuel for fulfilling its energy demand which is expensive as 11 well as not friendly for the environment. The need of the hour is to shift from fossil fuels to renew-12 able energy resources like geothermal, wind, solar etc. to cater for global warming issues. Pakistan 13 has a lot of potential geothermal sites because of several fault lines and hot springs. A sound 14 knowledge of ground temperature is essential to use geothermal energy, which is obtained by drill-15 ing boreholes and putting sensors making it an expensive procedure. Thus, to avoid huge cost for 16 drilling bore holes, particularly for ground temperature analysis, a numerical approach has been 17 considered for determining ground temperature. Furthermore, correlation charts between air and 18 ground temperatures have been developed as there were no proper studies on the ground temper-19 ature of Pakistan. Then, with the help of a boreholes drilled in National University of Sciences and 20 Technology Islamabad Pakistan, the actual ground and numerically calculated temperatures have 21 been compared which shows an error margin in the range between 0.27% for higher depths to 7.3% 22 near surface. Thus, it is shown that the proposed method is easy to implement and better than large 23 scale testing methods for the depths at which geothermal energy is extracted.

Partial shading on solar photovoltaic (PV) arrays is a prevalent problem in photovoltaic systems that impair the performance of PV modules and is responsible for reduced power output as compared to that in standard irradiance conditions thereby resulting in the appearance of multiple maximas on panel output power characteristics. These maxims contribute to mismatch power losses among PV modules. The mismatch losses depend on shading characteristics together with different interconnected configuration schemes of PV modules. The research presents a comparative analysis of partial shading effects on a 4 x4 PV array system connected in series(S), parallel (P), serries-parallel (SP),total-cross-tied (TCT),central-cross-tied(CCT),bridge-linked(BL),bridge-linked total cross-tied (BLTCT) ,honey-comb(HC), honey-comb total-cross-tied (HCTCT) and ladder (LD) configurations using MATLAB/Simulink. The PV module SPR-X20-250-BLK was used for modeling and simulation analysis. Each module is comprised of 72 number of PV cells and a combination of 16 PV modules was employed for the contextual analysis. Accurate mathematical modeling for the HCTCT configuration under partial shading conditions (PSCs) is provided for the first time and is verified from the simulation. The different configuration schemes were investigated under short-narrow,short-wide,long-narrow,long-wide, diagonal, entire row distribution, and entire column distribution partial shading condition patterns with mathematical implementation and simulation of passing clouds. The performance of array configurations is compared in terms of maximum power generated ), mismatch power loss (∆), relative power loss ) and the fill factor (FF). It was inferred that on average, TCT configuration yielded maximum power generation under all shading patterns among all PV modules interconnection configurations with minimum mismatch power losses followed by hybrid and conventional PV array configurations respectively.

The quantile estimation of extreme wind speed is needed in various environmental fields such as climatology, design of structures, renewable energy sources and agricultural operations. These calculations are crucial for the coding of wind speed. In this study, the required wind speed series of 16 stations in Khyber Pakhtunkhwa, Pakistan, was obtained from the NASA official website and measured in meters per second (m/s) at a 10-meter distance. A Regional Frequency Analysis of 16 AMWS stations was performed using L-moments. The quantile estimates of extreme wind speed are needed for various areas of interest using Regional Frequency Analysis (RFA) and extreme value theory. These calculations are crucial for the coding of wind speed. The data was taken from the NASA official website at a 10-meter distance and measured in meter per second (m/s). A Regional Frequency Analysis of AMWS using L-moments is performed utilizing wind speed data from sixteen sites (16) in Pakistan's Khyber Pakhtunkhwa province. There are no sites that are found to be discordant. The wards method is used to construct a homogenous region and make two homogenous regions from 16 sites. The heterogeneity test justifies that both clusters are homogeneous. The most appropriate probability distribution from the Generalized Normal (GNO), Generalized Logistic (GLO), Pearson Type-3 (P3), Generalized Pareto (GPA), and Generalized Extreme Value (GEV) distributions are chosen to calculate regional quantiles. According to the L-moments diagram and Z statistics, GEV for Cluster- Ι and GLO for Cluster- ΙΙ are the best suggestions from the others. Both clusters’ robustness is measured utilizing Relative Bias (RB) and Relative Root Mean Square Error (RRMSE). Overall, GEV distribution is fit for cluster-Ι, and the GLO distribution is fit for cluster-ΙΙ. Utilizing the site mean and median as index parameters, we can also find at-site quantiles from regional quantiles. The study’s quantile estimates can be employed in codified structural designs with policy consequences.

The community of farmers in land tenure have different institutional in terms of mastery of the land. In Indonesia there were generally institutional governing the utilization of land for mastery permanently, but there were also institutional governing dominion land in turn. This research aimed to chart institutional pattern characteristic mastery of the land inheritance system passes in, andanalyzeits contribution to sustainability of agriculture in the economic, social and ecological. Research method using case studies, with unit case a subdistrict in Gowa, South Sulawesi province, Indonesia. The results showed that institutional land pattern mastery system passes the inheritance patterns of alternation that has in effect hereditary, pattern rotation established by the heir land management patterns, depending on the number of beneficiaries, as well as not having managed to land fragmentation, so the scale of farming land, conditions can be maintained , the land was slanted so given a terracing, planting process was carried out by means of mutual. Neither found that institutional land pattern mastery system passes the inheritance had been contributing the sustainability of agriculture in social and ecological, but have yet to fully contribute to the sustainability of agriculture in economy.

Voltage Stability & Control, is very crucial compared to other Power System (PS) Quality and Stability issues. Long-Vertical-Power-Flows in Conventional Grids, causes voltage drops which in turn causes huge power losses, especially in the Medium Voltage (MV) and Low Voltage (LV) Distribution Networks. Such technical losses in abysmally-planned weak distribution networks, lead to substantial loss of revenues to the utility grid. Apart from classic Voltage Regulation (VR) techniques, with the rise of Distributed Generation (DG) based on Renewable Energy Sources (RES), Horizontal-Power-Flows can be introduced in the network, through various Smart Grid techniques. Coupling such sources, near load centers shall mitigate long flows from expensive conventional sources at times of huge demands, improving feeders’ Voltage Profile. This Ancillary Service of Voltage Support from DG RESs shall thereby alleviate revenue losses caused by long-power-flows in weak distribution grids. For a developing country like Pakistan, loss of revenue from an already expensive utility gives huge blow to the economy. So, a similar technique for voltage support is proposed for an 11-kV feeder, which faces similar problem, and the results are remarkable. The technique is implemented using OpenDSS Tool by modelling 3MWp PV Penetration along with some future storage.

Silybum marianum L. is a well-known medicinal herb, primarily used in liver protection. Light strongly affects several physiological processes along with secondary metabolites biosynthesis in plants. Herein, S. marianum was exploited for in vitro potential under different light regimes in the presence of melatonin. The optimum callogenic response occurred in combination of 1.0 mg/L α-naphthalene acetic acid and 0.5 mg/L 6-Benzylaminopurine under photoperiod. Continuous light associated with melatonin treatment increased total flavonoid content (TFC), total phenolic content (TPC) and antioxidant potential, followed by photoperiod and dark treatments. The increased level of melatonin has a synergistic effect on biomass accumulation under continuous light and photoperiod, while adverse effect was observed under dark condition. More detailed phytochemical analysis showed maximum total silymarin content (11.92 mg/g DW) when placed under continuous light + 1.0 mg/L melatonin. Individually, the level of silybins (A and B), silydianin, isolsilychristin and silychristin was found highest under continuous light. Anti-inflammatory activities were also studied and highest percent inhibition was recorded against 15-LOX for cultures cultivated under continuous light (42.33%). The current study helps to better understand the influence of melatonin and different light regimes on silymarin production as well as antioxidant and anti-inflammatory activities in S. marianum callus extracts.

Respiratory syncytial virus (RSV) is a leading cause of acute lower respiratory infections in young children worldwide. RSV-associated deaths in children are underreported in Bangladesh. We analyzed hospital-based surveillance data on severe acute respiratory infections (SARI) in under-five children before (August 2009–February 2020) and during the COVID-19 pandemic (March 2020–March 2022). Using the World Health Organization definition, we identified SARI cases in 14 tertiary-level hospitals. Nasopharyngeal and oropharyngeal swabs were collected for real-time reverse transcriptase-polymerase chain reaction (rRT-PCR) testing of six respiratory viruses, including RSV. SARI deaths during the pandemic (2.6%, 66) were higher than pre-pandemic (1.8%, 159; p<0.001). Nearly half of pandemic deaths (47%) had underlying respiratory viruses, similar to the pre-pandemic rate (45%). RSV detection in deaths was consistent pre-pandemic (13%, 20/159) and during the pandemic (12%, 8/66). Children aged <6 months constituted 57% (16) of RSV-related deaths. Evaluating interventions like maternal vaccination and infant monoclonal antibody prophylaxis is crucial to address RSV, a major contributor to under-five SARI deaths.

Load balancing to alleviate network congestion remains a critical challenge in Vehicular Ad-Hoc Networks (VANETs). During route and response scheduling, RSUs risk being overloaded beyond their calculated capacity. Despite recent advancements like RSU-based load transfer, NP-Hard hierarchical geography routing, RSU-based MAC schemes, simplified clustering, and network activity control, a significant gap persists in employing a load-balancing server for effective traffic management. We propose a server-based network congestion handling mechanism (SBNC) in VANETs to bridge this gap. Our approach clusters RSUs within specified ranges and incorporates dedicated load balancing and network scheduler RSUs to manage route selection and request-response scheduling, thereby balancing RSU loads. We introduce three key algorithms: optimal placement of dedicated RSUs, a scheduling policy for packets/data/requests/responses, and a congestion control algorithm for load balancing. Using the VanetMobiSim library of Network Simulator-2 (NS-2), we evaluate our approach based on residual energy consumption, end-to-end delay, packet delivery ratio (PDR), and control packet overhead. Results indicate substantial improvements in load balancing through our proposed server-based approach.

In Southeast Asia, the incidence of Leukemia, a malignant blood cancer originating from hema-topoietic progenitor cells, is on the rise, marked by a concerning 54% mortality rate. This study focuses on enhancing early-stage prediction to improve patient recovery prospects significantly. Leveraging Machine Learning and Data Science, we employ protein sequential data from frequently mutated genes such as BCL2, HSP90, PARP, and RB to predict Chronic Myeloid Leukemia (CML). Our approach relies on robust feature extraction techniques, namely Di-peptide Composition (DPC), Amino Acid Composition (AAC), and Pseudo amino acid composition (Pse-AAC), with prior attention to addressing outliers and validating feature selection through the Pearson Corre-lation Coefficient. Data augmentation ensures a well-rounded dataset for analysis. Employing a range of Machine Learning models, including Support Vector Machine (SVM), XGBoost, Random Forest (RF), K Nearest Neighbor (KNN), Decision Tree (DT), and Logistic Regression (LR), we achieve accuracy rates spanning from 66% to 94%. These classifiers undergo comprehensive as-sessment using performance metrics such as accuracy, sensitivity, specificity, F1-score, and the confusion matrix. Our proposed solution, encompassing a user-friendly web application dashboard, presents an invaluable tool for early CML diagnosis with profound implications for practitioners, offering a deploy-able asset within healthcare institutions and hospitals.

The textile processing sector is accountable for the extensive utilisation and pollution of freshwater resources. Due to heightened consumer awareness of environmental legislation regarding freshwater contamination, the textile sector is compelled to review and improve their current water consumption practices. Foan dyeing technique is a highly promising alternative that has the ability to contribute to a more sustainable future. This review paper discussed the current state of foam dyeing technology, highlighting its advantages in terms of re-duced consumption of water and energy, as well as minimal usage of dyes and chemicals compared to conventional methods. The foam configuration allows for more effective application of dyes. As a result, there is a decrease in dye consumption and a reduction in processing time. The process is environmen-tally sustainable since it significantly reduces water pollution. Furthermore, foam dyeing method consumes less energy due to its lower dying temperature need compared to conventional processing technology. Additionally, this paper highlights the continued investigation of foam dyeing on many types of textile substrates (such as fibres, yarns, and fabric) and compositions including cotton, polyester, and their mixtures. In addition, the techno-economic comparison of foam dyeing and conventional dyeing is also given. This review paper addi-tionally endorses the Sustainable Development Goals (SDG 6, clean water and sanitation) by examining the preservation of usable water and the decrease in wastewater discharge through foam dyeing technology. Lastly, the potential advantages of foam dyeing in terms of significantly reducing water consump-tion and the generation of waste in the textile industry were also addressed.

Herein we foremost detailed the numerical modeling of the double absorber layer- methyl ammonium lead iodide– carbon nitride layer solar cell and subsequently provided in-depth insight on the active layer associated with dominant radiative and non-radiative recombination losses limiting the efficiency ( ) of the solar cell. Under recombination kinetics phenomena, we explored the influence of Radiative recombination, Auger recombination, Shockley Read Hall recombination, the energy distribution of defects; Band Tail recombination (Hoping Model), Gaussian distribution, metastable defect states including single donor (0/+), single acceptor (-/0), Double Donor (0/+/2+), double acceptor (2/-/0-), and the interface layer defects on the output characteristics of the solar cell. Setting defect (or trap) density to with uniform energy distribution of defects for all the layers, we achieved the of 24. 16 %. A considerable enhancement in power conversion efficiency was perceived as we reduced the trap density to for the absorber layers. Further, it was observed that for the absorber layer with double donor defect states, the active layer should be carefully synthesized to reduce crystal order defects to keep the total defect density as low as to achieve efficient device characteristics

Haemonchus contortus (H. contortus) is a gastrointestinal parasite affecting small ruminants, leading to a significant decline in animal productivity. In this study, we developed a nanovaccine by encapsulating the recombinant protein rHcES-15, derived from the excretory/secretory products of H. contortus, within biodegradable poly (D, L-lactide-co-glycolide) (PLGA) nanoparticles (NPs). To construct the nanovaccine, PLGA NPs were prepared using a modified double emulsion solvent evaporation technique. Scanning electron microscopy (SEM) illustrated successful encapsulation of rHcES-15 within PLGA NPs, with a size ranging between 350-400 nm. The encapsulation efficiency (EE) of the antigen in the nanovaccine was determined to be 72%. A total of forty experimental mice were divided into five groups, receiving the nanovaccine on day 0 and being humanely sacrificed at the end of the 14-day trial. The stimulation index (SI) from mice vaccinated with the nanovaccine indicated an amplified lymphocyte proliferation and a significant increase in anti-inflammatory cytokines (IL-4, IL-10, and IL-17). Furthermore, the percentages of T-cells (CD4+, CD8+) and dendritic cell phenotypes (CD83+, CD86+) were substantially upregulated in mice immunized with the nanovaccine compared to control groups and the rHcES-15 group. Similarly, higher levels of antigen-specific serum immunoglobulins (IgG1, IgG2a, IgM) were observed in response to the nanovaccine compared to both the antigenic (rHcES-15) and control groups. In conclusion, the data strongly supports the notion that encapsulation of rHcES-15 within PLGA NPs effectively stimulates immune cells in vivo, ultimately augmenting antigen-specific adaptive immune responses against H. contortus. This discovery highlights the promising potential of the nanovaccine, justifying additional investigations to ascertain its efficacy finally.

Background: The psychomotor agitation of the behavioural and psychological symptoms of dementia (BPSD) is one of the common issues in aged care facilities, leading to the poor functional and medical consequences. Psychotropic interventions are the preferred choice of treatment, but which medication should be the prescribers first preference? This review aims to compare pharmacological interventions for psychomotor agitation, judging them according to their effectuality and justifiability profiles. This is to be achieved by retrieving information from Randomised Control Trials (RCTs) and systematic reviews. Objectives: This review evaluates evidence from RCTs, systematic reviews, and meta-analyses of BPSD patients who have taken agitation treatments. Assessing the efficacy of selective serotonin reuptake inhibitors (SSRI) and antipsychotic treatments when compared to each other for the purpose of improving agitation outcomes. Methods: This review includes RCT that compared one or more active ingredient medications with another medication or with a placebo, along with systematic reviews comparing citalopram (SSRI) with antipsychotics such as quetiapine, olanzapine, and risperidone. Studies were extracted by searching and accessing databases, such as PubMed, OVID, and Cochrane with restrictions of date from 2000 to 2021 and English language. Conclusion: There is still limited studies of SSRIs for the treatment of agitation in BPSD. SSRIs such as citalopram were associated with a reduction in symptoms of agitation, and lower risk of adverse effects compared to antipsychotics. Future studies are required to assess the long-term safety and efficacy of SSRI treatments for agitation in BPSD.

Today’s urban spaces face precipitous challenges and complications, which include the COVID-19 pandemic, urbanization, population growth, and climate change. Proximity plays an essential role in influencing the integrity of public spaces and urban environments, while proxemics studies people’s experience, and the benefits, of urban space, and is based on a behavioral system of activities that includes ‘territoriality’. There is a need to study the behavioural patterns of people in given situations with proxemic dimensions in order to sustain both human beings and the quality of urban space. However, people behave spontaneously within environmental settings and reflect each other’s responses, meaning it is important to distinguish between different cultures, which tend to respond in particular ways to the meaning of proximity. This suggests there is no universal indicator for phenomena such as crowding. The aim of this paper is to highlight the interrelationship between urban form and urban life. This study focuses on two patterns of activity - street life and social life - by adopting a descriptive-analytical approach to documentary and desk research. The findings reveal a vital distinction between social and public patterns of proximity, while other proximities, although critical, are not observed within interactions between people.

Background: Chronic Myeloid Leukemia (CML) is initiated in the bone marrow due to the chromosomal translocation t(9;22), resulting in the fusion oncogene BCR-ABL. Tyrosine kinase inhibitors (TKIs) targeting BCR-ABL have transformed fatal CML into an almost curable disease. However, TKIs lose efficacy during disease progression, and the mechanism of CML progression remains to be fully understood. Additionally, common molecular biomarkers for CML progression are lacking. Our studies previously detected ANKRD36 (c.1183_1184 delGC and c.1187_1188 dupTT) associated exclusively with advanced phase CML. However, clinical validation of this finding was pending. Therefore, this study aimed to clinically validate mutated ANKRD36 as a novel biomarker of CML progression. Materials and Methods: The study enrolled 124 patients in all phases of CML, recruited from Mayo Hospital and Hameed Latif Hospital in Lahore, Punjab, between January 2020 and September 2023. All response criteria were adopted from the European LeukemiaNet guideline 2020. Informed consent was obtained from all study subjects. The study was approved byscientific and ethical review committees of all participating centers. Sanger sequencing was employed to detect ANKRD36mutations in CML patients in accelerated phase (AP) (n=11) and blast crisis (BC) (n=10), with chronic-phase CML (CP-CML) patients as controls (n=103). Samples were processed using Big Dye Terminator Cycle Sequencing Ready Reaction kits and sequenced using ABI Prism 3730 Genetic Analyzer, and sequencing using forward and reverse primers for ANKRD36.Results: During our study, 17% of CML patients progressed to advanced phases AP-CML n= 11 (8.9%) and BC-CML n=10(8.1%). The chronic- and advanced-phase patients showed significant difference with respect to male-to-female ratio, hemoglobin level, WBC count, and platelet count. Sanger sequencing detected ANKRD36 mutations c.1183_1184 delGC and c.1187_1185 dupTT exclusively in all AP- and BC-CML patients but in none of the CP-CML patients. Nevertheless, mutations status was not associated with male-to-female ratio, hemoglobin level, WBC count, and platelet count, which makes ANKRD32 as an independent predictor of early and terminal disease progression in CML. Conclusions: The study confirms ANKRD36 as a novelgenomic biomarker for early and late CML progression. Further prospective studies should be carried out in this regard. ANKRD36, although fully uncharacterized in humans, shows the highest expression in bone marrow, particularly myeloid cells. Functional integrated genomic studies are recommended to further explore the role of ANKRD36 in the biology and pathogenesis of CML.

This study was carried out to formulate and evaluate controlled release (CR) matrix tablets of Acyclovir using combination of hydrophilic and hydrophobic polymers. Acyclovir is a guanine derivative and is its half-life is short hence administered five times a day using immediate release tablets. Six formulations (F1-F6) were developed using Ethocel and Carbopol in equal combinations at drug-polymer (D:P) ratio of 10:5, 10:6, 10:7, 10:8, 10:9 and 10:10. Solubility study was performed using six different solvents. The compatibility studies were carried out using FTIR and DSC. According to USP, Quality Control and dimensional tests (hardness, friability, disintegration and thickness) were executed. In-vitro drug release studies of Acyclovir was carried out in dissolution apparatus using using 0.1 N HCl medium at constant temperature of 37 ± 0.5 ºC. In order to analyze the drug release kinetics, five different mathematical models were applied to the release data. The results showed that there was no incompatibility between drug and polymers. Physical QC tests were found within limits of USP. The release was retarded upto 24 hrs and non-fickian in-vitro drug release mechanism was found. A formulation developed using blend of polymers, showed excellent retention and desired release profiles thus providing absolute control for 24 hrs.

In an urban context, the street network can be considered the most substantial element, as its role is to create the whole urban setting. The street network is a spatial pattern that can be recognized as a linkage bonding other components of the urban context, such as buildings and open spaces. Basically, the street is not only a collection of lines that transfer people, vehicles and goods but also denote a broad range of activities and influences people’s responses. In this respect, some studies address the street as a network that entails two key elements, link and node; the link can be defined by the type of mechanism that it connects, while the node can be identified according to the analysis technique. Defining the street’s elements is a crucial step in ascertaining the expression of whatever is a link or/and a node. Thus, some scholars use the link to refer to a street, and node for the intersection, while others employ the opposite meaning. Two different viewpoints deal with spatial network analysis; the first is a technique based on topological depth, such as Space Syntax SS, and the second is Multiple Centrality Assessment (MCA) that is employed for metric analysis. This paper compares Space Syntax (SS) and Multiple Centrality Assessment (MCA) by measuring the integration and centrality of the street, and highlights the points of similarity and difference between the two techniques.

Objective: To investigate social, economic, and environmental contributors to quit or continue smoking and vaping during the COVID-19 pandemic. Methods: A qualitative study design was adopted to identify smokers’ beliefs in a LMIC, using a small community sample. Results: 276 participants were primarily surveyed. Motivation to continue smoking included temporary pleasurable effects, working remotely, stress or anxiety, whereas a motivator to quit smoking was the overlap with COVID-19 symptomatology. There was a rise in social awareness regarding the potential harm of smoking and vaping during the pandemic yet those participants who were younger felt they were immune from its morbid complications. Conclusions: With paradoxical associations of COVID-19 with cigarette and vape usage, it is important to pay attention to biases in data in favor of educating its users of the increased risk of severe disease.

Thai basil is a renowned medicinal plant and a rich source of bioactive antioxidant compounds having several health benefits, with actions to prevent of cancer, diabetes and cardiovascular disease. Plant cell and tissue culture technologies can be routinely established as an important, sustainable and low-cost biomass source for the production of high-value phytochemicals. The current study aimed at developing an effective protocol for the production of Thai basil leaf derived callus cultures with sustainable and high production of biomass and antioxidants as an alternative of leaves production. MS basal medium with various concentrations of plant growth regulators (PGRs) compatible with nutraceutical applications (i.e., gibberellic acid (GA3) and 6-benzylaminopurine (BAP) either alone or in combination with naphthalene acetic acid (NAA)) were evaluated. Among all tested PGRs, the combination BAP:NAA (5 mg/L:1 mg/L) yield maximum biomass accumulation (fresh weight (FW): 190 g/L and dry weight (DW): 13.05 g/L) as well as enhanced phenolic (346.08 mg/L) production. HPLC quantification analysis indicated high productions of chicoric acid (35.77 mg/g DW) and rosmarinic acid (7.35 mg/g DW) under optimized callus culture conditions. Antioxidant potential was assessed using both in vitro cell free and in vivo cellular antioxidant assays. Maximum in vitro antioxidant activity DPPH (93.2 % of radical scavenging activity) and ABTS (1322 µM Trolox equivalent antioxidant capacity) was also observed for the extracts from callus cultures grown on optimal conditions. In vivo cellular antioxidant activity assay confirmed the effective protection against oxidative stress of the corresponding extract by the maximum inhibition of ROS and RNS production. Compared to commercial leaves, callus extracts showed higher production of chicoric acid and rosmarinic acid associated with higher antioxidant capacity. In addition, this biological system also has a large capacity for continuous biomass production, thus demonstrating its high potential for possible nutraceutical applications.

Hepatitis B and C are major health issues in developing countries such as Pakistan and Afghan-istan. The aim of this study was to determine the prevalence and effectiveness of a screening program for hepatitis B and C in a region with no existing programs, and to estimate their prev-alence in the general population in Khyber Pakhtunkhwa Province, Pakistan, as well as in Afghan refugees or migrants. A prospective cohort study was done in the general population of Peshawar and its adjacent districts, as well as migrants from neighboring provinces of Afghani-stan, who presented to our tertiary-care health facility. A Microsoft Excel registry was created for data collection, which were analyzed using IBM SPSS via descriptive analysis, normal distribution curve histograms, and chi-squared tests. A total of 9563 individuals were screened for hepatitis (5894 males and 3669 females), including Afghan migrants in Peshawar and surrounding districts. 876 individuals tested positive for hepatitis, with 538 positive for hepatitis B (383 males and 155 females) and 330 positive for hepatitis C (198 males and 134 females). Eight individuals had a hepatitis B and C co-infection. Among the study population, the prevalence rates were 2.2% for hepatitis B and 2.3% for hepatitis C, of which the Afghan migrants accounted for 2.7% and 0.5%, respectively. According to the gender-based distribution, hepatitis B was more prevalent in males, whereas there was no significant gender-based difference for hepatitis C. Our results highlight the need for a comprehensive approach to control hepatitis B and C in Pakistan and Afghanistan. Increased awareness, improved healthcare, and preventive measures such as screening and elimination programs to prevent severe liver diseases and eradicate hepatitis are necessary.

Nowadays, more than 180 million people believe that the Holy Qur'an was sent by the Almighty Allah through Prophet Muhammad in 610-632 A.D in Mecca and Medina. However, the word Mecca (Q: 48:24) is mentioned only once in the entire Holy Qur'an, which is not related to the birth of the Prophet or any worship. Conventional Islam is mostly based on the hearsay of some Islamic narrators published in the eighth and ninth centuries. To think deeply and conduct research on the verses of the Holy Quran has been mentioned (special urge) directly and indirectly by this Holy Scripture itself many times but it would not be wrong to say that there is no scholarship on the verses of the Quran based on the research method described in the Holy Quran until the present century. Therefore, this paper has been dared to carry out by combining the methods of research followed in the Holy Quran and the academically accepted research methodology. The analysis shows that the results of almost fourteen hundred years of mythological history of conventional Islamic narrators are opposites. First of all, the proper name of the Prophet revealed by the Holy Quran is Ahmed, but Muhammad is an adjective and there are many such names. Secondly, this prophet was not born in Mecca, KSA, nor in 570/571 A.D, but in the Beqaa Valley of Lebanon, between the third and fourth centuries. Thirdly, the Muslim Hajj (pilgrimage) of Mecca is celebrated entirely according to the Lahwal Hadith (idle tales) (Q: 31:6) in the language of the Holy Quran. Originally the place designated for pilgrimage was in the Beqaa Valley, Lebanon. This article will have a double influence on the Muslim world, that is, Islamic scholars will think again deeply and research new ways of scholarship of the Holy Quran, instead of based on the hearsay of idle tales (Lahwal Hadith). On the contrary, those who are stubborn Islamic narrators, since they have already rejected the Holy Quran, will not hesitate to violently attack the researchers and they will not be positively motivated by this paper. This article specifically urges Islamic scholars to conduct in-depth studies on the most important issues of Islam using the Holy Quranic research method.

The study experimentally investigated a novel approach for producing hydrogen from methane cracking in dielectric barrier discharge catalytic plasma reactor using a nanocatalyst. Plasma-catalytic methane (CH4) cracking was undertaken in a dielectric barrier discharge (DBD) catalytic plasma reactor using Ni/MgAl2O4. The Ni/MgAl2O4 was synthesised through co-precipitation followed customised hydrothermal method. The physicochemical properties of the catalyst were examined using X-ray diffraction (XRD), scanning electron microscopy - energy dispersive X-ray spectrometry (SEM-EDX) and thermogravimetric analysis (TGA). The Ni/MgAl2O4 shows a porous structure spinel MgAl2O4 and thermal stability. In the catalytic-plasma methane cracking, the Ni/MgAl2O4 shows 80% of the maximum conversion of CH4 with H2 selectivity 75%. Furthermore, the stability of the catalyst was encouraging 16 hours with CH4 conversion above 75%, and the selectivity of H2 was above 70%. This is attributed to the synergistic effect of the catalyst and plasma. The plasma-catalytic CH4 cracking is a promising technology for the simultaneous H2 and carbon nanotubes (CNTs) production for energy storage applications.

COVID-19 infection is extremely dangerous for persons with comorbidities such as kidney disease and diabetes. Although many people of all ages and socioeconomic backgrounds have suffered due to this pandemic, those with underlying medical conditions like kidney disease and diabetes are more vulnerable to becoming infected with COVID-19 related to weak immunity. However, the role of vaccination in the co-infection of COVID-19 with diabetics is not available in the literature. Therefore, we examine the unique challenges presented by the co-infection of COVID-19 in individuals with diabetes, focusing on its disease transmission dynamics. A mathematical modelling technique is to be employed in this work to analyse the dynamics of COVID-19 outbreaks with seven compartments, including vaccination with comorbidities such as diabetes. We also investigated analytically by displaying the solutions' existence, boundedness, positivity and sensitivity. After calculating the basic reproduction numbers, the stability analysis of model equilibrium points is also covered. If the reproduction numbers are less than unity, the disease-free equilibrium points of the model appear to be both locally and globally stable. The findings of this study are that as the vaccination rate rises, the incidence of COVID-19 and its co-infections with diabetes decreases. Effective disease treatment strategies may be based partly on the possible impact of vaccination on the co-infection of COVID-19 related to diabetic disease insights.

In archaea, the interaction of HerA helicase and NurA nuclease is required for 3' end resection during DNA double-stranded break repair, and its disruption results in unfaithful DNA repair. Interactions transpire by the four conserved domains, including the N-terminal HAS domain (HerA-ATP synthase), which serves as a binding site for the exonuclease NurA. As a HerA hexamer between its two subunits, the conserved C-terminal brace extension functions as an adjacent brace. DBD serves as a location for DNA binding, which causes the DNA strands to be propelled into the HerA pocket to begin unwinding. The putative pore entrance is made up of four helix coils, which provide a suitable charged surface for guiding DNA into the pore. The crystal structure of the complex HerA-NurA allows for the identification of key residues for protein-protein interaction. This allows us to predict that most archaeal HerA orthologs will be able to interact with one another. Archaeal HerA is a homo-hexameric assembly featuring a DNA-binding domain that is conserved. It also features distinctive ATP and NurA binding domains. Following the structure and sequence conservation criteria, we find one HerA ortholog in Pyrobaculum calidifontis and multiple HerA paralogs, but the role of none is established yet.Interestingly, orthologous HerA is part of an Mre11-Rad50 gene neighborhood while paralogous HerA is not, which could be misleading. As a result, it sought to describe the criteria that may be used as a possible fingerprint for identifying orthologous genes, as well as the cloning procedures and tactics that would aid in the confirmation of the HerA helicase in P. calidifontis. Their confirmation is based on PCR cloning and characterization following HerA construct creation.

Cotton (Gossypium spp.) is a major source of natural fiber and an important cash crop. The cotton growth habit and architecture determine its productivity and influence management strategies for commercial production. The GATA transcription factors (TFs) control various developmental processes in plants, such as flower, bract and embryo development, and petal differentiation. As stable transformation is still a bottleneck in many plant species, TRV-VIGS was used to manipulate gene expression in different plants, including Gossypium hirsutum L. In this study, we undertook the TRV-based VIGS to functionally characterize two candidate genes, Gohir.D05G103700 and Gohir.D12G153600, identified through the expression QTL analysis for five floral induction and meristem identity genes using the upland cotton mini-core collection. Virus-induced silencing of the Gohir.D05G103700 gene resulted in up to a 1.4-fold reduction in the transcript level in two inoculated plants, G3 and G4, and Gohir.D12G153600 gene resulted in up to a 2.3-fold reduction in transcript level in a single inoculated plant P05 relative to the mock-treated plant. The TRV2-Gohir.D05G103700 inoculated plants precisely G3 and G4 also exhibited loss of the supernumerary (fourth) floral bract in the squares, whereas the TRV2-Gohir.D12G153600 inoculated plants did not show any observable phenotypic change relative to the mock-treated plants.  Altogether, this study suggested that TRV-VIGS can be used to characterize genes in cotton relatively rapidly and the cotton Gohir.D05G103700 gene is a positive regulator of the indeterminate growth habit in cotton, which could be manipulated to obtain a cotton plant with architecture best suited for the cultivation area.

Background: The psychomotor agitation of the BPSD is one of the common issues in aged care facilities, leading to the poor functional and medical consequences. Psychotropic interventions are the preferable choice of treatment. But which medication should be the prescribers first preference? This review aims to compare pharmacological interventions for psychomotor agitation, judging them according to their effectuality and justifiability profiles. This is to be achieved by retrieving information from RCTs and systematic reviews. Objectives: This review evaluates evidence from RCTs, systematic reviews, and meta-analyses of BPSD patients who had taken agitation treatments. Assessing the efficacy of antidepressants and antipsychotic treatments when compared to each other for the purpose of improving agitation outcomes. Methods: This narrative review includes RCTs and retrospective studies that were comparing one or more active ingredient medications with another or with a placebo, along with sys-tematic reviews comparing antidepressants with antipsychotics such as quetiapine, olanzapine, and risperidone. Studies extracted by searching accessing databases, such as PubMed, OVID, and Cochrane with restrictions of date from 2000 to 2021 and English language. Quality of evidence: The quality of systematic reviews was judged against AMSTAR score, and RCTs were judged according to CONSORT checklist for RCT protocols. Conclusion: There are still few studies of serotonin targeting treatment of agitation in BPSD. The SSRIs such as citalopram were associated with a reduction in symptoms of agitation, and lower risk of adverse effects compared to antipsychotics. This review also illustrates brexpiprazole as a target of multimodal neurotransmitters such as dopamine, serotonin, and norepinephrine; and dextromethorphan, OR dextromethorphan associated with bupropion or quinidine as a blockade of NMDA receptors. The outcome of this review suggests that further studies involving more dementia/Alzheimer’s participants should be conducted. Future studies are required also to assess the long-term safety and efficacy of SSRI, brexpiprazole, dextromethorphan treatments for agitation in BPSD.

Background: Women in rural districts of Pakistan face numerous barriers to healthcare, rendering gender-responsive health programming important, including for Tuberculosis (TB). This study was conducted to assess the general understanding of TB and of access to healthcare for women, as a first step towards implementation of a gender responsive TB programme in TandoAllayar, a rural district of Pakistan. Methods: A total of 36 participants were interviewed. The focus group discussion guide comprised of questions on: (1) family/household dynamics (2) community norms (3) healthcare system (4) women’s access to healthcare (5) TB Awareness;, and (6) women’s access to TB Care. Results: Limited autonomy in household financial decision-making, disapproval of unassisted travel, long travel time, lack of prioritization of spending on women’s health and inadequate presence of female health providers, were identified as barriers to access of healthcare for women, higher in younger women. Facilitators to access of TB care included a reported lack of TB-related stigma, moderate knowledge about TB disease, and broad understanding of tuberculosis as a curable disease. Other suggested facilitators include health facilities closer to the villages and the availability of higher quality services. Conclusion: Significant barriers are faced by women in access to TB care in rural districts of Pakistan. Programme implementers in high burden countries, should shift towards improved gender-responsive TB programming.

Keeping in mind the increasing trend and need for serious games in science education, we have done a systematic literature review. These papers show the trends and patterns of research carried out in this field from the year 2011 to 2020. Specifically, we investigated country-wise concentration and the most common evaluation methods. Literature is reviewed from IEEEexplore, Springer, and Scopus. Moreover, we discussed the role of Augmented Reality(AR) games in teaching physics. Lastly, we have discussed the positive and negative aspects of serious games in science education in particular, and the trend of using serious games in the past decade in education in general.

LIFI was first introduce by Professor Harald Haas on July 2011. Light fidelity (LI-FI) may be a technology which uses light as a medium to travel from one place to a different. It uses Light like Light Emitting Diode (LED) visible radiation Communication (VLC) for data Transferring and Internet connection. LIFI may be a technique which uses light as a medium because it uses light to travel it's 20 times faster than any WIFI within the world. during this paper we speak about things like what's LIFI and the way it's better then WIFI why we want LIFI and What changes did bring LIFI in our Future LIFI. How it'll make IOT devices far better than before The Technique to implement LIFI and also the problem we face of implementation of LIFI

Bacterial infections are world-wide problem and resistant bacteria is increasing globally that lead to treatments failure. Thus, it is important to find new techniques that are effective for the treatment antibiotic-resistant microorganisms. Green medicine used for the medication of different bacterial infection. Therefore , the study aimed to evaluate the immunomodulatory activity of essential fatty acid semi carbazide (EFASC) compounds extracted from flaxseed to eradicate resistance pathogens . Crud extracts of Linum usitatissimum was extracted by hexane for extraction of EFASC. The results of LD₅₀ appear that a live suspension of E.coli was 0.49×10⁷ ,while HK E.coli was 10⁸ , 125 mg /ml were the optimum dose in stimulate immune response of EFASC which gave maximum dose of total WBC , Neutrophil and Monocyte count. The immunomodulatory activity appear that E.coli + EFASC released moderate levels of IL-4 . HK E.coli release higher IL-4 lead to increase the hypersensitivity and hyper responses of immune system. HK + EFASC immunogen revealed moderate increased in IL-12 mean level 0.99 pg /ml, HK bacteria recorded 1.49 pg/ml, while the mean of EFASC revealed no significant different compare with control. An effective protection was observed in immunized groups with HK E.coli and EFASC challenged with 100 of LD50 of a live E.coli.

This paper presents a concise exploration of several analytical methods for extracting the parameters of the single-diode model (SDM) of a photovoltaic (PV) module under standard test conditions (STC). The paper investigates six methods and presents the detailed mathematical analysis leading to the development of each method. To evaluate the performance of these methods, MATLAB-based software has been developed and deployed to synthesize the results of each method when used to extract the SDM parameters of various PV test modules of different PV technologies. Similar software has also been developed to extract the same parameters using well-established numerical and iterative techniques. A comparison is subsequently made between the synthesized results and those obtained using numerical and iterative methods. The comparison indicates that in spite of the fact that analytical methods may involve fair amount of approximations, their accuracy can be comparable to that of their numerical and iterative counterparts, with the added advantage of significant reduction in computational complexity, and without the initialization and convergence difficulties, which are normally associated with numerical methods.

Carrageenan (car-), used in the pharmaceutical as well as food industry, is marine sulfated polysaccharides. The carrageenan blends (CB) of kappa (κ-), iota (ι-), and lambda (λ-) of 50/50 weight by weight are multipurpose and biocompatible hydrophilic polymers. They were subjected to adsorption of copper (Cu2+) ions. The aim of the study was to conduct extensive rheological and mechanical studies rendering them suitable for biological purposes. The rheology was conducted at various temperatures using a frequency curve, frequency sweep, loss modulus, and storage modulus analysis. Models of rheology like Ostwald, Bingham, and Modified Bingham models were utilized. The rheological results demonstrated non-Newtonian/pseudo-plastic behavior at various temperatures. The models of rheology demonstrated good flow properties and rheological performance of these materials. These materials could be exploited for their application in pharmaceuticals, food, and cosmetics. Thus, our study reflects that these CB can be safely exploited in the healthcare, pharmaceutical, and food industry. However, further studies should be conducted to evaluate their effectiveness in clinical studies.

Generic object detection is one of the most important and flourishing branches of computer vision and has real-life applications in our day to day life. With the exponential development of deep learning-based techniques for object detection, the performance has enhanced considerably over the last 2 decades. However, due to the data-hungry nature of deep models, they don't perform well on tasks which have very limited labeled dataset available. To handle this problem, we proposed a transfer learning-based deep learning approach for detecting multiple pigs in the indoor farm setting. The approach is based on YOLO-v2 and the initial parameters are used as the optimal starting values for train-ing the network. Compared to the original YOLO-v2, we transformed the detector to detect only one class of objects i.e. pigs and the back-ground. For training the network, the farm-specific data is annotated with the bounding boxes enclosing pigs in the top view. Experiments are performed on a different configuration of the pen in the farm and convincing results have been achieved while using a few hundred annotated frames for fine-tuning the network.

Animal behavior analysis is a crucial tasks for the industrial farming. In an indoor farm setting, extracting Key joints of animal is essential for tracking the animal for longer period of time. In this paper, we proposed a deep network that exploit transfer learning to trained the network for the pig skeleton extraction in an end to end fashion. The backbone of the architecture is based on hourglass stacked dense-net. In order to train the network, key frames are selected from the test data using K-mean sampler. In total, 9 Keypoints are annotated that gives a brief detailed behavior analysis in the farm setting. Extensive experiments are conducted and the quantitative results show that the network has the potential of increasing the tracking performance by a substantial margin.

Infertility affects approximately 15% of couples worldwide, an estimated 30% of which is related to male factor infertility. Application of low level laser therapy (LLLT) to improve fertility status is a rapidly growing discipline in medicine. Laser therapy triggers a variety of biological processes through interaction with primary cellular photoacceptors. The present review aims at evaluating the literature available in the MEDLINE/ PubMed on cellular and molecular mechanisms of photobiomodulation in the domains of reproductive and veterinary medicine. We primarily focused on the clinical application of laser treatment on seminal quality, in particular its role in promoting spermatozoa motility, as well as the role of phototherapy in modulating assisted reproduction (ART). Additionally, we investigated the strength of evidence in support of the positive impact of photobiomodulation on facilitating ART.

Background: The biofilm-forming bacteria Porphyromonas gingivalis (P. gingivalis) is primarily responsible for periodontal disorders, which continue to be a global health issue. Despite the widespread use of antibiotics like metronidazole, other potent therapeutic a crucial quorum sensing molecule implicated in the formation of P. gingivalis biofilm. Approaches are now being explored due to the growing challenge of antibiotic resistance. Objective: In particular, chemicals from Symphytum Officinale (S) and Panax Ginseng (G) plants will be examined in this study to assess if they have the ability to inhibit biofilm and to prevent the development of acylated homoserine lactones (AHLs), a quorum sensing molecule. Materials and Methods: With Metronidazole serving as a control, the antibacterial effects of these substances (Symphytum Officinale and Panax Ginseng) were examined against a standard strain and a clinical isolate of P. gingivalis. Dilutions of these plant extracts were used either alone (G+S) or in conjunction with metronidazole (G+S+F), to assess their antibacterial activity using antibacterial susceptibility test (inhibition zone), biofilm inhibition and disruption assay (optical density) and quorum sensing inhibition assay (AHL). Results: The combinations of Symphytum officinale, Panax Ginseng and metronidazole (S+G+F) showed the maximum effectiveness with highest zone of inhibition (25.000±0.001 mm) and biofilm inhibition (98.46%), and were comparable to G+S (inhibition zone of 24.341±0.593 mm and biofilm inhibition of 97.76%), and significantly different in the degree of biofilm inhibition with different treatment scenarios. Additionally, the plant's extracts and combinations are specific concentrations had a significant effect on the suppression of the generation of AHL (p &lt; 0.05). Conclusion: According to preliminary research, these plant-derived substances, especially when paired with metronidazole, significantly inhibited the growth of P. gingivalis biofilm providing valuable information for the development of innovative therapeutic approaches for periodontitis and other biofilm-associated illnesses.

Recent progress in microfabrication technique allowed the rapid development of neural implants. They are getting categorized as effective tools for clinical practice, especially to treat traumatic and neurodegenerative disorders. Microelectrode arrays already have been used in numerous neural interface devices. Basically, almost all neural implants have been developed based on BCI (Brain Computer Interface) system. When BCI system falls under invasive technique, it is referred as BMI or Brain Machine Interface. BMIs hold promises for neurorehabilitation of motor and sensory function, cognitive state evaluation and treatment of neurological chaos. A directed overview of the field of neural implants is discussed in this article. The aim of this review is to give a brief introduction of neural prosthetics as well as their exciting applications in treating neurological disorders and a deep discussion on their functionality are mentioned. BCI system and their different types, their functionality, their pros and cons, how other neural implants developed, and their present status have been covered. Different possibilities and possible future of deep brain stimulation (DBS), Neuralink, motor and sensory neural prosthetics are further discussed.

In this study, we present different methods of estimating fuzzy reliability of a two-parameter Rayleigh distribution via the maximum likelihood estimator, median first-order statistics estimator, quartile estimator, L-moment estimator, and mixed Thompson-type estimator. The mean-square error MSE as a measurement for comparing the considered methods using simulation through different values for the parameters and unalike sample sizes is used. The results of simulation show that the fuzziness values are better than the real values for all sample sizes, as well as the fuzzy reliability at the estimation of the Maximum

This research aims to identify the role of the Dyson model for strategic development in achieving strategic success, and the starting point of the research was the following main question: What is the role of the Dyson model in achieving success?The research was applied in the field in the departments of the Baghdad Municipality, where the examination list was relied upon, which included a set of questions that the senior and middle leaders in the Baghdad Municipality answered, and it was the main means by which the information related to the field of research was collected, and the checklist included two variables and three dimensions From each variable, as each dimension included four questions that express indicators that revolve around one of the research hypotheses, and the case study methodology was used, which defined its path and steps, collected and analyzed field data, and linked it to its theoretical framework, in order to reach To achieve the goal of completing this research, and through analyzing, interpreting and discussing the results, the most important results were drawn up: It was found that the principle of motivation within the departments of Baghdad Municipality does not exist and this affects the employees who do not receive it from the higher leaders in their departments, and this shows that the leaderships in The Municipality of Baghdad do not have the skills and experience. Baghdad Municipality seeks to work alone and not to involve employees who have experiences and skills and strive to achieve development in their departments, and this is what the community members expressed. Among them and poor business completion in their departments.

In this work, PMMA(Poly methyl methacrylate) microfluidic system was used as a micro-reactor for urea hydrolysis by urease enzyme with use conductivity principle and utilize sound level meter(SLM) App in smartphone as a novel detector by considering the peak height in the App as an indicate for urea concentration. the advantage of use small volume and how the reaction carried on in the microfluidic system with simple and low cost are discussed, and the results were analyzed and statically determine. The linearity, detection limit (3×noise )and Correlation Coefficient, 62.5-500 ppm, 31.25 ppm and 0.992 respectively also, recovery studied were between(98.5-100.13%).

4-component relativistic atomic and molecular calculations are typically performed within the no-pair approximation where negative-energy solutions are discarded, hence the symmetry between electronic and positronic solutions is not considered. These states are however needed in QED calculations, where furthermore charge conjugation symmetry becomes an issue. In this work we shall discuss the realization of charge conjugation symmetry of the Dirac equation in a central field within the finite basis approximation. Three schemes for basis set construction are considered: restricted, inverse and dual kinetic balance. We find that charge conjugation symmetry can be realized within the restricted and inverse kinetic balance prescriptions, but only with a special form of basis functions that does not obey the right boundary conditions of the radial wavefunctions. The dual kinetic balance prescription is on the other hand compatible with charge conjugation symmetry without restricting the form of the radial basis functions. However, since charge conjugation relates solutions of opposite value of the quantum number κ, this requires the use of basis sets chosen according to total angular momentum j rather than orbital angular momentum ` . As a special case, we consider the free-particle Dirac equation, where the solutions of opposite sign of energy are related by charge conjugation symmetry. We note that there is additional symmetry in those solutions of the same value of κ come in pairs of opposite energy.

In this paper, it is proved that s-iteration with error and Picard-Mann iteration with error iterative processes converge strongly to the unique fixed point of Lipschitzian strongly pseudo-contractive map. This convergence is almost -stable and -stable. Applications of these results to the operator equations, where is a strongly accretive and accretive mappings of into itself.

Keywords: Requirements prioritization, Next release plan, Software product planning, Decision support, MoSCoW, AHP, K-Menas, GMM, BIRCH, PAM, Hierarchical, Clustering, Clusters Evaluation

Background: The important periodontal disease pathogen Porphyromonas gingivalis produces large biofilms that increase its pathogenicity. Finding natural antimicrobial agents is crucial because of the rise in antibiotic resistance. Objective: The purpose of this study was to determine if plant extracts such as Symphytum officinale (S) and Panax ginseng (G) were effective against P. gingivalis separately and in combination with a common antibiotic Metronidazole (F). Materials and Procedures: Six different dilutions were produced the plant extracts and antibiotic separately and in combination with G and F and S and F using two-fold serial dilution technique. To evaluate the effects of these substances biofilm inhibition experiments were conducted. Plaque samples were collected from periodontitis patients to isolate P. gingivalis and standard strain of P. gingivalis (ATCC 33277) were bought. Additionally, Acylated Homoserine Lactones (AHLs) detection was carried out to look for any activity that would interfere with quorum sensing. GraphPad prism was used for statistical analysis with p value &lt; 0.05. Results: The combinations of Symphytum Officinale and Metronidazole (S+F) showed the maximum effectiveness in biofilm inhibition (98.7%), which was better than G+F (98.2%) with substantial variations in biofilm inhibition levels in different treatment regimes. Notably, the isolate from the patient was more active than the standard strain. Additionally, the plant extracts and their combinations at particular dilutions had notable inhibitory effects on the generation of AHL (p &lt;0.05). Conclusion: The study highlights the possibility of Symphytum Officinale and Panax Ginseng as effective treatments for P. gingivalis biofilm and AHLs, both on their own and in combination with Metronidazole. These organic substances may open the door to cutting-edge methods of treating periodontal disorders.

The present study was conducted the status of sea bass from Kokko and Kyuntone of The Gulf of Motttama Wetland (GoMW) area in Thanatpin Township in Bago Region Myanmar from September 2019 to August 2020. Fifty specimens were monthly collected, measured and weighed. Invoices of sea bass were collected for the depot and fish sellers by monthly. In Kokko, mean value of standard length and body weight were highest in March (32.70±1.58, 660.7±112.23). The mean value of standard length was peak in January (31.39±7.16) but peak of body weight was in March (963.24±280.86) in Kyuntone villages. The lowest mean value of standard length and body weight were found in June at both study areas. According to the invoice data revealed that monthly catch weight of sea bass is most abundance in October (829.92) kg in Kokko, (339.12) kg in Kyuntone. Based on price of relations to size group, small size C &lt; 300g (41%) was mostly abundance in Kokko and in Kyuntone small size C &lt; 300g (35%) was second abundance. Specimens were not landed in April and May. In June, young specimens were very rarely seen in both study sites. The important roles of wetland fishes, the economic valuation of GOMW in Myanmar and samples of fishing gear and value chain of sea bass in Myanmar was expressed in this study.

In addressing the challenges of data scarcity in biometrics, this study explores the generation of synthetic palmprint images as an efficient, cost effective, and privacy preserving alternative to real-world data reliance. Traditional methods for synthetic biometric image creation primarily involve orientation modifications and filter applications, with no established method specific to palmprints. We introduced the utilization of the “Style-based generator”, StyleGAN2-ADA, from the StyleGAN series, renowned for generating high-quality images. Furthermore, we explore the capabilities of its successor, StyleGAN3, which boasts enhanced image generation, facilitating smooth and realistic transitions. By comparing the performance of StyleGAN3 on public dataset, we aim to establish the most efficient generative model for this purpose. Evaluations were conducted using the SIFT (Scale-Invariant Feature Transform) algorithm into our evaluation framework. Preliminary findings suggest that StyleGAN3 offers superior generative capabilities, enhancing equivariance in synthetic palmprint generation.

In this work, we introduce a new concepts for $\alpha$-type $F$-Suzuki contraction and $\alpha$-type $F$-weak-Suzuki contraction in the context of $b$-metric spaces. Compared to the $\alpha$-type $F$-contraction and $F$-Suzuki contraction mappings, these contractions are essentially weaker. For these type of contraction mappings, sufficient conditions are established for the fixed point's existence and uniqueness in $b$-metric spaces. As a result, the findings encompass several generalizations. To show the usability of our obtained results, we provide a supportive example and an application to a non-linear differential equation with fractional order.

Background: Video assisted thoracoscopic surgery (VATS) has become the recommended approach for treatment of resectable lung cancer. However, no large randomized clinical trial has been conducted formally comparing surgical resections completed by VATS to those done by open thoracotomy (OT) in low volume centers. The current study sought to assess differences in recurrence-free survival (RFS), overall survival (OS), positive margins and postoperative length of stay (LOS) between VATS and OT lobectomies in our center. Method: A single institution retrospective chart review from May 2005 through May 2015 was conducted. All patients diagnosed with stage I through III lung cancer who underwent surgical resection were selected. Patient and tumor characteristics recorded included age at diagnosis, sex, tobacco use, tumor location (side and lobe), stage, size and receipt of chemotherapy or radiotherapy. Chis-square and Wilcoxon-Mann-Whitney tests were used to compare demographics, tumor characteristics and LOS. Multiple logistic and Cox regression analyses were used to compute relative risk (RR) for positive margins and mortality hazard ratios along with 95 percent confidence intervals (95%CI), respectively. Results: Of the 235 patients, 101 subjects had VATS while OT was performed in 134 patients. Age at diagnosis, sex, tobacco use, tumor location, and size were comparable for VATS and OT. No significant difference was observed in the relative risk of positive margins for VATS versus OT, RR = 0.56 (95%CI = 0.26, 1.05). However, VATS had shorter median LOS compared to OT (4 vs. 6 days, respectively), p = 0.002. A comparison of VATS versus OT showed no significant difference in the risk of recurrence, HR = 1.21 (95%CI = 0.74, 2.00), or death, HR = 1.34 (95%CI = 0.88, 2.06), in the intent-to-treat population. Similarly, no significant differences in recurrence or mortality risk were observed between VATS versus OT for analyses conducted separately for each cancer stage group or those limited to patients with negative margins. Conclusion: Our study indicates that compared to OT, VATS leads to shorter LOS while achieving comparable margins status, recurrence-free and overall survival regardless of tumor stage at diagnosis.

This paper focused on impact localization of composite structures, which possess more complexity in the guided wave propagation because of the anisotropic behavior of composite materials. In this work, a composite plate was manufactured by using a compression molding process with proper pressure and temperature cycle. Eight layers of woven composite prepreg were used to manufacture the composite plate. A structural health monitoring (SHM) technique is implemented with piezoelectric wafer active sensors (PWAS) to detect and localize the impact on the plate. There are two types of impact event are considered in this paper (a) low energy impact event (b) high energy impact event. Two clusters of sensors recorded the guided acoustic waves generated from the impact. The acoustic signals are then analyzed using a wavelet transform based time-frequency analysis. The proposed SHM technique successfully detect and localize the impact event on the plate. The experimentally measured impact locations are compared with the actual impact locations. An immersion ultrasonic scanning method was used to visualize the composite plate before and after the impact event. A high frequency 10 MHz 1-inch focused transducer was used to scan the plate in the immersion tank. Scanning results show that there is no visible manufacturing damage in the composite plate. However, clear impact damage was observed after the high-energy impact event.

This paper utilizes a life cycle assessment to evaluate the energy resources and environmental impacts of three heating systems. In the first step, life cycle assessments (LCAs) are prepared for the renewable, conventional, and combined systems. The system boundary of the LCA method is "cradle to gate," which means it includes the entire life cycle of a product or process. This includes energy supply, transport, energy generation, and operational energy use. The system scenarios were compared based on ecological and energy loads in the second step. Primary energy, resources, emissions, and environmental potentials are calculated for the system scenarios using the life cycle assessment methods CML 2016 and ReCiPe 2016. Finally, models for environmental reliability and complex decision-support tools have been developed. This work addresses two main questions: how to characterize the environmental and energy impacts of the systems under study, and what is the optimal scenario for the system? The research results show that the gas boiler system has a greater environmental impact. The most significant differences between the systems relate to the degrada-tion of abiotic fossil fuels when using a gas boiler and the process of acidification when using an electric heat pump. The results can be used to develop sustainable heating systems with reduced environmental impacts and enhanced energy efficiency.

Bioprinting is a relatively new yet evolving technique predominantly used in regenerative medicine and tissue engineering. 3D bioprinting techniques combine the advantages of creating Extracellular Matrix (ECM) like environments for cells and computer-aided tailoring of predetermined tissue shapes and structures. The essential application of bioprinting is for the regeneration or restoration of damaged and injured tissues by producing implantable tissues and organs. The capability of bioprinting is yet to be fully scrutinized in sectors like the patient-specific spatial distribution of cells, bio-robotics, etc. In this review, currently developed experimental systems and strategies for the bioprinting of different types of tissues as well as for drug delivery and cancer research are explored for potential applications. This review also digs into the most recent opportunities and future possibilities for the efficient implementation of bioprinting to restructure medical and technological practices.

The study conducts a comparative analysis of solar radiation estimation methods, assessing the efficacy of the Heliosat-2 algorithm against ground measurements across seven distinct countries: Netherlands, Spain, Japan, Namibia, South Africa, Saudi Arabia, and India. To achieve this, it utilizes two distinct satellite data sources—Himawari-8 for Japan and Metosat Second Generation-MSG for the rest of the countries—spanning the years Jan 2022 to April 2024. A robust methodology for determining albedo parameters specific to Heliosat-2 was developed. During cloudy days, the estimates provided by Heliosat-2 generally exceeded the ground measurements in all the countries. Conversely, on clear days, there was a tendency for underestimation, as indicated by the median value of the mean bias (MB) across most of the countries. The Heliosat-2 model slightly underestimates daily radiation values, with a median MB ranging from −27.5 to +10.2 W.m⁻². Notably, the median root mean squared error (RMSE) on clear days is significantly lower, with values ranging from 24.8 to 108.7 W.m⁻², compared to cloudy days where RMSE values lie between 75.3 and 180.2 W.m⁻². In terms of R² values, both satellites show a strong correlation between the estimated and actual values, with a median value consistently above 0.86 on a monthly scale and over 92% of daily data points falling within ±2 standard deviation.

Citizen Science has come up to perform analytics over the SARS-CoV-2 genome. Public GALAXY servers provide an automated platform for genomics analysis. Study includes design of GALAXY workflows for RNASEQ assembly and annotation as well as genomic variant discovery and perform analysis across four samples of SARS-CoV-2 infected humans obtained from the local population of Wuhan, China. It provides information about transcriptomics and genomic variants across the SARS-CoV-2 genome. Study can be extended to perform evolutionary and comparative study across each species of coronaviruses. Augmented and integrated study with cheminformatics and immunoinformatics will be a way forward for drug discovery and vaccine development.

This paper proposes an ARIMA approach to battery health forecasting with accuracy improvement by K shape-based clustered predictors. The health prediction of the battery pack is an important function of a battery management system in data centers. Accurate forecasting of battery life turns out to be very difficult without failure data to train a good forecasting model in real life. The conventional ARIMA model is compared with total and clustered predictors for battery health forecasting. Results show that the forecasting accuracy of the ARIMA model significantly improved by utilizing the results of the clustered predictors for 40 batteries in a real data center. One year of actual historical data of 40 batteries of large scale datacenter is presented to validate the effectiveness of the proposed methodology.

Since the 1980s, a growing interest in goat milk was noticed due to the nutritional values and health benefits of this milk, which resulted in increasing goat populations and milk production worldwide. This comprehensive review elaborates on goat milk composition compared to other types of milk. It is also an overview of goat milk production, properties, nourishment-value, applications in dairy products, and potential health benefits. Goat milk composition and its characteristics are slightly different from other types of milk and can be utilized to manufacture many dairy products. Fresh goat milk and goat milk products (e.g., yogurt and kefir were found to provide various potential health benefits, such as anti-inflammatory, prevent cardiovascular disease, anti-diabetic and antihypertensive, strengthen bones, boost immunity, and improve metabolism.

Abstract: The Tropical Rainfall Measuring Mission (TRMM) and then Global Precipitation Mission (GPM) are the most important and widely used data sources in the forecasting of drought, flood, and water resources management. However, since this sensor’s data is primarily used for tropical regions, it is necessary to evaluate the accuracy for optimal use of the data across varying climatic and physiographic conditions. In this study, the accuracy of the satellite data for a span of 17 years (2000-2017) for three climatic zones has been explored using synoptic ground station data. The climates include a) arid and low rainfall, b) semi-arid and low rainfall, and c) humid and high rainfall. We evaluated satellite data accuracy in drought and wet conditions based on the Standard Precipitation Index (S.P.I.) and different seasons. For available ground control stations, 13 stations were used in the humid, seven stations in a semi-arid climate, and 12 stations in the dry climate. The results show that the monthly precipitation product of GPM (IMERG product) and TRMM (TMPA/3B43 product) overestimate the rainfall. In the arid climate, the precipitation is estimated 43%, in the semi-arid environment 50%, and in the humid weather 11% more than the ground-based data on average. Therefore, to use satellite data in different climates, it is necessary to make corrections to obtain precise results. Based on 32 ground stations, the correction coefficient has a positive relationship with average precipitation and altitude and an inverse relationship with the latitude. Further in-depth investigations showed that the accuracy of satellite data in wet conditions is higher than the accuracy of normal circumstances, and the accuracy of normal conditions is more accurate than drought conditions. Besides, the accuracy of satellite data in wet or dry conditions increases with increasing time scales. The highest accuracy was obtained for a 12-month time scale and the lowest accuracy for the 3-month time scale of drought conditions in the arid climate.

The deposition of dust particles on solar panel modules constitutes a significant challenge, leading to a potential reduction in solar cell performance. This work tackles this issue by investigating the surface modification of a layer of transparent indium tin oxide (ITO), with a detailed analysis of the influence of its characteristics via different annealing conditions/processing. The ITO layer has been studied to enhance its characteristics for dust removal applications. Of particular note is that the developed ITO layer can be applied to dust removal using electrostatic or magnetic-based approaches. Thus, the correlation between annealing gas (using Argon, Oxygen, and Nitrogen), annealing temperature, and annealing ramping rate is explored with the obtained surface topography, as well as electrical and optical properties. The developed ITO layers annealed in the Argon medium at 600°C with an annealing ramping rate of 50°C/s showed smooth surface roughness, the highest electrical conductivity, and a relatively low refractive index. Such findings can play a crucial role in the future implementation of using the enhanced ITO layer for dust mitigation in solar panels, thus improving their long-term performance.

We introduce the notion of generalized contraction on dualistic partial metric spaces. A fixed point theorem for mappings satisfying above mentioned contraction is obtained. Some consequences of our result are obtained. We construct an example to demonstrate the effectiveness of our result among the corresponding results in partial metric spaces. Our results provide substantial generalizations and improvements of several well known results existing in the comparable literature. We discuss an application of our fixed point results to show the existence of solution of functional equations.

The traditional standards employed for pain assessment have many limitations. One such limitation is reliability because of inter-observer variability. Therefore, there have been many approaches to automate the task of pain recognition. Recently, deep-learning methods have appeared to solve many challenges, such as feature selection and cases with a small number of data sets. This study provides a systematic review of pain-recognition systems that are based on deep-learning models for the last two years only. Furthermore, it presents the major deep-learning methods that were used in review papers. Finally, it provides a discussion of the challenges and open issues.

Increased construction activities in Australia have led to the generation of a massive volume of construction and demolition (C&D) waste annually. Management of this volume of waste requires an effective waste framework. The literature reported that the current Australian waste framework does not meet expectations and needs immediate improvements. This study was therefore conducted to seek the key C&D stakeholders' opinion about various issues identified in this waste stream. The specific objectives of this study are identification of the main barriers to effective C&D waste management, the impact of current regulations and opportunities to enhance the current C&D waste management system. A survey was conducted in 2019 to capture the stakeholders' perception. 132 participants from various industries and government agencies based in various Australian jurisdictions took part in the survey. The key results showed that the main barriers towards an effective management system are "overregulation, tough acceptance criteria, and increased testing requirements", "lack of local market" and "culture, poor education and low acceptance". Furthermore, a low number of participants indicated that the current legislation encourages waste recovery activities. The main areas of improvements included "providing a guideline that determines the accepted level of contamination for reusing C&D waste”, "preparation of guidelines on requirements of using recycled C&D materials in different industries" and "setting target for reduction, reusing, and recycling C&D waste". The results can inform policy development and be used as evidence for a broader discussion to solve lasting issues in C&D waste management.

With the advent of digitization, the integration of advanced technologies in operations and projects across all sectors is in progress. Accordingly, efforts are being made to utilize cutting-edge technologies to improve the circularity of the built environment. This study aimed to review the existing applications and limitations of building information modeling (BIM) tools for circular economy (CE) implementation from this perspective. A literature review was conducted to provide an overview of the use of BIM tools for conducting life cycle assessments, energy analysis, waste management, and formulation of material passports for buildings. It was found that BIM tools, which are available across all life cycle phases of building, have a great potential to improve the circularity of the sector. The overview provided on the use of various BIM tools may help stakeholders of the built environment understand the role of BIM for CE adoption in the sector.

High antioxidants level in food is gradually becoming popular because of the enhanced risk of oxidative stress in humans. Bread wheat is rich in vital antioxidants but its major bioactive compounds are not available for the human. This study was conducted with the aim to enhance the phytochemical constituents and antioxidative activity of wheat grains by fermenting it with the use of Bacillus subtilis KCTC 13241. The antioxidative potential was determined by DPPH (2,2-diphenyl-1-picryl- hydrazyl) and ABTS (3-ethyl-benzothiazo- line-6-sulfonic acid) radical scavenging assay as well by the concentration of amino acids, flavonoids, minerals, carbohydrates, and phenolic compounds. Different varieties showed different free radical scavenging potential on fermentation, which was significantly high with respect to their corresponding unfermented wheat varieties. The highest potential was found in a fermented wheat variety named Namhae and this combination can be used in the pharmaceutical and food industries.

Sustainable development and education in sustainable development (ESD) are crucial and interconnected topics under wide discussion today. Young adults need to be educated in how to help bring about change. Thus, the dynamic relationship between school and home is important. In education, use could be made of English language classes, especially since English is a global language that enables access to the sustainability literature and facilitates discussion in global conferences and meetings. Consequently, English as a foreign language (EFL) students could gain confidence from being able to understand and use the terminology of, for example, sustainability. In this paper, the use of competence-based language teaching (CBLT) is proposed as a means of introducing sustainability topics into EFL writing classes at a university in Saudi Arabia. Students’ competence in sustainable development is therefore considered based on their ability to write about suggested sustainable development topics, measured on a scale for five dimensions of ESD proposed by Michelsen and Fischer (2017). The results demonstrate that the students possessed competence in sustainable development and intended to participate in its implementation. Thus, recommendations are made for the stakeholders in the education sector to include sustainable development topics as an initial offering in the curricula of various specialties using the CBLT approach.

Keywords: knowledge; behaviour; ergonomics; posture; musculoskeletal; pain; university; students; survey.

Different materials prepared by appropriate synthesis methods and applying different post syn-thesis processes could be used as hole transport layer in perovskite solar cells. In the present work annealing was employed to enhance physical properties of copper oxide (CuO) thin films fabricated via spin coating technique and the effects of annealing on their optical, morphological, electrical and structural properties were investigated. The XRD findings revealed the polycrystalline structure with large crystallite size. Optical spectra showed larger transmission beyond the visible region, reduced absorption, and a decrease in bandgap energy from 1.93 eV to 1.81 eV. The Ag phonon modes at 299.22 and 304 cm-1 shown by the Raman shift confirmed the development of the CuO pure phase. FTIR spectra showed the Cu-O stretching band at 759, 764 and 446 cm−1. SEM revealed the agglomeration of nano crystallites with large grains on the surface. The carrier type conductivity of annealed CuO thin films was determined via two-point hot probe technique. Low resistivity values were determined via four-point probe method. These findings indicate that CuO thin films may be successfully used as a companion with an n-type layer in p-n junction solar cells, and a hole transport layer in perovskite solar cells.

: This study aims at exploring Turkish consumers’ behaviors toward purchasing green fashion. A mixed-methods approach was used in this study. Six experts from the main brands in the fashion industry in Türkiye were interviewed. A total of 268 questionnaires were collected from Turkish consumers, and their responses were analyzed. The theory of planned behavior (TPB) informed the theoretical framework of this study. The main components of the TPB were extended to include perceived consumer effectiveness. A thematic analysis was conducted to analyze and code the interviews. To test the hypotheses, structural equation modeling (SEM) was conducted. The findings show that the key factors of the TPB, i.e., attitudes (ATTs), subjective norms (SNs), and perceived behavioral control (PBC), as well as perceived consumer effectiveness, significantly impact the intentions of Turkish consumers to purchase sustainable fashion. However, the results highlight some inconsistencies, gaps, and barriers that discourage the purchase intentions of consumers, including a lack of information, misinformation, greenwashing, green skepticism, a lack of trust, and the high cost of sustainable fashion.

Abstract Incretin mimetics, also known as glucagon-like peptide-1 (GLP-1) receptor agonists, are a class of medications used to treat type 2 diabetes by mimicking the actions of incretin hormones in the body. These hormones are responsible for promoting insulin release from the pancreas in response to nutrient intake, as well as decreasing glucagon secretion, slowing gastric emptying, and promoting satiety. By imitating these actions, incretin mimetics help to regulate blood sugar levels in individuals with diabetes and glucose intolerance. One of the key benefits of incretin mimetics is its ability to lower blood sugar levels without causing hypoglycemia. This is especially important for individuals with diabetes who may experience dangerous drops in blood sugar levels when using other medications. Additionally, incretin mimetics have been shown to promote weight loss in some individuals, making them a valuable option for those struggling with obesity in addition to diabetes. Incretin mimetics are administered by injection, once or twice daily, depending on the specific medication. They are often combined with other diabetes medications, such as metformin or insulin, for optimal blood sugar control. These medications are generally well-tolerated, with common side effects including nausea, vomiting, and diarrhea, which usually diminish over time as the body adjusts to the medication. Studies have shown that incretin mimetics can help improve cardiovascular outcomes in individuals with diabetes, including reducing the risk of heart attacks and strokes. This is particularly significant given the increased risk of cardiovascular disease in individuals with diabetes. Incretin mimetics also have been shown to preserve pancreatic beta-cell function, which is responsible for producing insulin. This can help slow the progression of diabetes and reduce the need for higher insulin doses over time. Despite their many benefits, incretin mimetics are not without limitations. They can be expensive compared to other diabetes medications, which may make them less accessible for some individuals. Additionally, there have been concerns about the potential risk of pancreatitis and pancreatic cancer associated with the use of these medications. However, more research is needed to fully understand these risks. It is important for healthcare providers to carefully assess each individual's unique needs and medical history when considering the use of incretin mimetics. They may not be appropriate for everyone, particularly those with a history of pancreatitis or pancreatic cancer. Patients should also be educated about these medications' proper administration and potential side effects to ensure their safety and efficacy. Overall, incretin mimetics have emerged as an important therapeutic option for individuals with type 2 diabetes, offering a unique mechanism of action that can help improve blood sugar control, promote weight loss, and reduce cardiovascular risk. With ongoing research and development in this field, incretin mimetics continue to show promise as valuable tools in managing diabetes and its associated complications and comorbidities.

Human papillomavirus (HPV) infections, primarily transmitted through sexual contact, have been linked to various cancers, including cervical, penile, anal, oropharynx, breast, and prostate cancers. This study presents a unique case of concurrent high-risk HPV35, HPV45, and HPV59 infections in both prostate and bladder cancer tissues from a single patient, representing the first documented instance worldwide with identical HPV types detected in two adjacent organs of the same individual. Employing a multiplex-PCR approach, gel electrophoresis, and Sanger sequencing, we confirmed the presence of these high-risk HPV types. Additionally, Western blot analysis using an HPV E7 antibody demonstrated the active expression of HPV oncoproteins in both cancer types. This discovery underscores the potential for HPV intra-organ transmission and necessitates further exploration of alternative transmission routes. The implications of our results offer new insights into the complex dynamics of HPV transmission in cancer pathogenesis.

Newcastle disease virus (NDV) causes a highly contagious and devastating disease in poultry, Newcastle disease (ND). ND causes heavy economic losses to the global poultry industry by decreasing the growth rate, decrease egg productions, mortality, and morbidity. Although, significant advances have been made in the vaccine development, but outbreaks are reported in vaccinated birds leading to overall decreased growth rate. In this study, we report the damage caused by the NDV infection in the pancreatic tissues of vaccinated as well as specific pathogen free chickens. The histopathological examination of the pancreas showed sever damage in the form of partial depletion of zymogen granules, acinar cell vacuolization, necrosis, and apoptosis, congestion in the large and small vessels, sloughing of epithelial cells of pancreatic duct, and mild perivascular edema. Increased plasma levels of corticosterone, somatostatin, were observed in NDV infected chicks at 3 and 5-day post infection (DPI). Slight decrease in the plasma concentrations of the insulin were noticed at 5 DPI. Significant changes were not observed in the plasma levels of glucagon. Furthermore, NDV infection has decreases the activity and mRNA expression of amylase, lipase, and trypsin from the pancreas. Taken together, our findings highlight that NDV induces extensive tissue damage in pancreas, decrease the activity and expression of pancreatic enzymes and increase plasma corticosterone and somatostatin.

Structural design optimization (SDO) plays a pivotal role in enhancing various aspects of construction projects, including design quality, cost-efficiency, safety, and structural reliability. Recent endeavors in academia and industry have sought to harness the potential of Building Information Modeling (BIM) and optimization algorithms to optimize SDO and improve design outcomes. This review paper aims to synthesize these efforts, shedding light on how SDO contributes to project coordination. Furthermore, the integration of sustainability considerations and the application of innovative technologies and optimization algorithms in SDO necessitate more interactive early-stage collaboration among project stakeholders. This study offers a comprehensive exploration of contemporary research in integrated SDO employing BIM and optimization algorithms. It commences with an exploratory investigation, employing both qualitative and quantitative analysis techniques following the PRISMA systematic review methodology. Subsequently, an open-ended opinion survey was conducted among construction industry professionals in Europe. This survey yields valuable insights into the coordination challenges and potential solutions arising from technological shifts and interoperability concerns associated with widespread SDO implementation. These preliminary steps of systematic review and industry survey furnish a robust knowledge foundation, enabling the proposal of an intelligent framework for automating early-stage sustainable structural design optimization (ESSDO) within the construction sector. The framework ESSDO addresses the challenges of fragmented collaboration between architects and structural engineers. This proposed framework seamlessly integrates with the BIM platform, i.e., Autodesk Revit for architects. It extracts crucial architectural data and transfers it to the structural design and analysis platform, i.e., Autodesk Robot Structural Analysis (RSA), for structural engineers via the visual programming tool Dynamo. Once the optimization occurs, optimal outcomes are visualized within BIM environments. This visualization elevates interactive collaborations between architects and engineers, facilitating automation throughout the workflow and smoother information exchange.

Photonic sensors are innovative devices that leverage the principles of light-matter interaction to enable precise and efficient detection of various physical parameters. These sensors operate by exploiting the interaction between photons, the fundamental particles of light, and matter. The light propagates through an optical waveguide, and a portion of the electromagnetic field extends beyond the waveguide surface, forming the evanescent field. This evanescent field interacts with the surrounding medium, allowing for highly sensitive detection of changes in the refractive index or properties of nearby substances. The underlying concept involves the modulation of light properties, such as intensity, wavelength, or phase, when it interacts with a target substance or undergoes changes in the surrounding environment. The advancements in photonic sensor technology have paved the way for enhanced sensitivity, selectivity, and miniaturization, making them invaluable tools in diverse industries. The ability to harness light-matter interactions for sensing purposes not only facilitates highly sensitive measurements but also allows for non-intrusive and remote monitoring, contributing to the evolution of smart and connected systems. In this overview, the material platforms and waveguide structures are explored that can make highly sensitive photonic devices applied to gas and biosensing applications.

A derivative series of 3,4-dimethoxy-β-nitrostyrene were synthesized and identified including new compound 6. The effect of antimicrobial activity of 3,4-alkyloxy modification of β-nitrostyrene was investigated. A molecular docking was also performed to obtain information about their interactions with Protein Tyrosine Phosphatase 1B (PTP1B). PTP1B containing cysteine 215 and arginine 221 as essential active residues plays a key role in signaling pathways that regulate various cell functions of microorganisms, which also act as negative regulator in signaling pathways of insulin that are involved in type 2 diabetes and other metabolic diseases. Compound 5 and 6 were the most potent as fragment of PTP1B inhibitor based on molecular docking, but compound 5 was more effective against Candida albicans. These compounds interact with serine 216 and arginine 221 residues. However, further research is needed to investigate their potential medicinal use.

Triple negative breast cancer (TNBC) is the most aggressive breast cancer accounting for around 15% of identified breast cancer cases. TNBC, by lacking estrogen receptor (ER), progesterone receptor (PR), and human epidermal growth factor receptor 2 (HER2), is unresponsive to current targeted therapies. Existing treatment relies on chemotherapeutic treatment but, despite an initial response to chemotherapy, the inception of resistance and relapse is unfortunately common. Dasatinib is an approved second-generation inhibitor of multiple tyrosine kinases and literature data strongly support its use in the management of TNBC. However, dasatinib binds to plasma proteins and undergoes extensive metabolism through oxidation and conjugation. To protect dasatinib from fast pharmacokinetic degradation and to prolong its activity, it was encapsulated on poly(styrene-co-maleic acid) (SMA) micelles. The obtained SMA-dasatinib nanoparticles (NPs) were evaluated for their physicochemical properties, in vitro antiproliferative activity in different TNBC cell lines, and in vivo anticancer activity in a syngeneic model of breast cancer. Obtained results showed that SMA-dasatinib is more potent against 4T1 TNBC tumor growth in vivo compared to free drug. This enhanced effect was ascribed to the encapsulation of the drug protecting it from a rapid metabolism. Our finding highlights the often-overlooked value of nanoformulations in protecting its cargo from degradation. Overall, results may provide an alternative therapeutic strategy for TNBC management.

Type 2 diabetes mellitus (T2DM) is a global health concern driven by factors such as obesity, sedentary behavior, and poor diet. This study uses data from the 2017-18 Bangladesh Demographic and Health Survey (BDHS) to analyze regional and individual predictors of diabetes and predi-abetes. Employing a Bayesian multinomial mixed-effects model, we account for regional varia-bility and individual factors like age, gender, BMI, residence, wealth, education, employment, and hypertension. Our results indicate significant regional differences and associations between de-mographic and health-related factors with diabetes risk. Younger individuals and those with higher BMI are more likely to be diabetic, while hypertension significantly increases diabetes risk. We applied machine learning (ML) models, including logistic regression, decision trees, k-nearest neighbor, linear discriminant analysis, and random forest, to classify diabetic status using these predictors, assessing their accuracy through 10-fold cross-validation. Logistic regression and linear discriminant analysis demonstrated robust performance across various response distributions. Simulation studies further examined the impact of different response distributions on model performance, revealing significant differences in classification accuracies. This approach of esti-mating parameters with a Bayesian model, applying ML for prediction, and conducting simulation studies to explore various scenarios highlights the importance of integrating these methodologies for effective diabetes prediction, providing insights for public health strategies to mitigate T2DM's impact.

The consumption and sale of fresh-cut products and salads have been growing tremendously in the present era. Therefore, the microbial safety of such products is of great concern. In the current study, a survey of general microbiological safety of fresh-cut produce and salads at quick-service restaurants (QSR) was undertaken across the Kingdom of Saudi Arabia. These findings were compared with microbiological criteria for foodstuffs by Saudi standards, metrology, and quality organization SASO-GSO-1016. Of the 82 samples of fresh-cut produce, 7% of samples were found to be unsatisfactory or beyond the acceptable limits. TPC count was unsatisfactory at 22%, coliform at 48%, and Staphylococcus aureus at 4%. For 108 samples for fresh salads, 11% of samples were found to be unsatisfactory or beyond the acceptable limits,13%, 27%, 4%, and 27% of samples showed an unsatisfactory range of TPC, coliforms, S. aureus, and Escherichia coli, respectively. The fresh-cut produce and salads were microbiologically safe in the central region compared to the eastern region followed by the western region. The relatively higher count was found in green pepper, mixed vegetables, and lettuce followed by fresh-cut onions and coleslaw salads. No Salmonella was detected in both fresh-cut produce and salads. The restaurants should be more stringent in their processing to ensure the consumer safety. Washing and sanitization of produce is the only way to reduce the diffusion of food borne pathogens.

The most potential renewable energy source for global emissions reductions is green hydrogen production. Iraq is looking into several sources of alternative energy to lessen its dependency on fossil fuels and to considerably cut its carbon dioxide emissions. This research examined the conceptual framework for the production and consumption of green hydrogen in Iraq. On the basis of accessible official and public data from government agencies, the potential capabilities of renewable energy resources are assessed, and certain fair assumptions are also established for a full study and evaluation of a possible hydrogen production in the country. The data presented here demonstrate conclusively that the contributions of renewable energy to the production of green hydrogen are substantial, giving the country prominence in the area of green hydrogen production. A pathway for a green hydrogen economy in the country by 2050 is proposed by this research based on its analysis. It is distributed in three stages: green hydrogen as a fuel for industry; using green hydrogen for fuel cells; and hydrogen commercialization. On the other hand, the research found a number of challenges to the implementation of a green hydrogen production that can be used in Iraq and other developing countries, including technological, economic, and social problems in addition to the related policy consequences.

Cancer cachexia is a multifactorial syndrome that is identified by ongoing muscle atrophy, along with functional impairment, anorexia, weakness, fatigue, anemia, reduced tolerance to antitumor treatments. Thus, reducing the patients’ quality of life. Cachexia alone causes about 22-25% of cancer deaths. This review covers the symptoms, mediators, available treatment, and prospects of 3D bioprinting for cancer cachexia. Studies about cachexia have shown several factors that drive this disease – protein breakdown, inflammatory cytokines activation, and mitochondrial alteration. Even with proper nutrition, physical exercises, anti-inflammatory agents, chemotherapy, and grafting attempts, standard treatment has been unsuccessful for cachexia. But the use of 3D bioprinting shows much promise compared to conventional methods by attempting to fabricate 3D constructs mimicking the native muscle tissues. In this review, some 3D bioprinting techniques with their advantages and drawbacks, along with their achievements and challenges in in-vivo applications have been discussed. Constructs with neural integration or muscle-tendon units aim to repair muscle atrophy. But it is still difficult to properly bio-print these complex muscles. Although progress can be made by developing new bio-inks or 3D printers to fabricate high-resolution constructs. Using secondary data, this review study shows prospects of why 3D bioprinting can be a good alternate approach to fight cachexia.

Background: One of the most common occupational health hazard and serious health concern, now a days, recognized is Musculoskeletal disorders (MSDs). The high prevalence among students and teachers is a major cause of decline in their health related quality of life and work performance. This study aimed to identify the prevalence of musculoskeletal disorders among teachers and students during online education. Methods: A cross-sectional survey was conducted among university faculty members and students who were involved in online education during COVID-19. Data collection was carried out electronically through a validated Arabic version of the Nordic Musculoskeletal Questionnaire (NMQ) which is self reported. A total of 175 respondents responded to the questionnaire (response 60%). Results: The prevalence of any part of the body was 90.3%. The commonest site of MSDs for past 12 months was the low back (65.7%), the neck (58.3%), and shoulders (57.7%). Females (80%) suffered more than males (20%). The students reported slightly higher MSDs as compared to teachers (93.1% vs 90.3). Binominal regression analysis showed association of females with low back pain “OR: 2.24 (95% CI): 1.04-4.83; p = 0.03” and neck pain “OR: 2.7 (95% CI): 1.24–5.84; p = 0.012)” while bad posture was associated with pain in upper back “OR: 3.46 (95% CI): 1.73-6.93; p = 0.001”. Conclusion: The faculty members and students are prone to high MSDs during online classes and significant measures should be taken to reduce the prevalence by addressing associated risk factors.

Aim: this scoping review was designed to identify studies that assess the adverse drug reactions (ADRs) for older people in Australian aged-care facilities. This review critically evaluated each published study to identify the risk of, or actual adverse drug events in older people. Inclusion criteria: This review considered any clinical studies that examined the adverse effects of medications in older people who were living in aged-care facilities. This review considered qualitative studies, analytical studies, RCTs, descriptive cross-sectional studies, and analytic observational studies that explored the use of medications and their adverse effects on older people in clinical settings (including aged care facilities). Methods: An initial search of the PubMed, OvidSP, EBSCOHost, MEDLINE, ScienceDirect, Wiley Online, SAGE, and SCOPUS databases, with full text was performed, followed by an analysis of the article’s title and abstract. Additionally, MeSH was used to describe the article. The initial round of the database search was based on inclusion criteria from studies that assessed tools or protocols aiming to identify the adverse effects of medications on the elderly population suffering chronic conditions or multiple co-morbidities. Two reviewers screened the retrieved papers for inclusion. The data presented in this review are in tabular forms and a narrative summary which aligns with the review’s objectives. Results: Seven studies were identified, and the extracted data from these studies were grouped according their characteristics and the auditing results of each study. Conclusion: There was no comprehensive or broadly adverse drug reaction assessment tool derived from Australian data that has been used on the elderly in an Australian healthcare setting.

City zones have become increasingly overcrowded as a result of the extensive population widening ratio and the swift relocation of people from villages. The traffic monitoring process is a major issue in these areas due to the massive traffic flow on the roads. This research proposed a cluster-based improved authentication and communication scheme for an Intelligent Transportation System in Vehicular AdHoc Networks (VANETs). Our primary objective is to optimize resource sharing in vehicular communication. We enhanced the reliability, scalability, and stability of fast-moving VANETs by introducing cluster-based routing schemes for Vehicle-to-Vehicle (V2V) and Vehicle-to-Infrastructure (V2I) communications. We used a third-party certification authority for vehicle authentication to address security and privacy concerns. Our proposed schemes support minimizing the end-to-end (E2E) delay and route request, in addition to reducing link failure. Our schemes’ leading yield includes throughput enhancement, TCP Socket Initialization time minimization, TCP handshake response speedup, and DNS lookup improvement. The schemes are centred on short-range peer-to-peer (P2P) wireless communication in a 400-meter radius cluster. This includes innovative P2P wireless communications on VANET using minimized resources. The proposed schemes deliver a secure authentication mechanism with a securely generated vehicle authentication key provided by a certification authority. Furthermore, we have developed RESTful APIs in vehicular communication for implementation purposes, and also offered and implemented algorithms for resource sharing regarding V2V and V2I communication. Ultimately, we evaluated the performance of our experiments.

Drinking water supplies in the developing world often serve as a biosphere for various organisms. Viral gastroenteritis is a neglected area of research in Pakistan, there is no data for the prevalence of enteric viruses in drinking water of the largest city of Karachi. The present study aimed to provide a survey of the existence of enteric viruses: human adenovirus (HAdV), human enteroviruses (hEV), and genotype A rotavirus (GARV) in tap water. Using a simple PCR approach, we detected 20%, 43%, and 23% of HAdV, hEV, and GARV in tap water respectively. We have also shown an overall quality of tap water at the pumping station and consumer tap. Moreover, we assessed the efficiency of small-scale water treatment methods for the removal of viruses.

Construction 4.0 is witnessing exponential growth in Digital Twin (DT) technology developments and applications, revolutionizing the adoption of Building Information Modelling (BIM) and other emerging technologies used throughout the lifecycle of the built environment. BIM provides technologies, procedures, and data schemas representing building components and systems. At the same time, DT enhances this with real-time data for cyber-physical integration, enabling live asset monitoring and better decision-making. Despite being in the early stages of development, DT applications have rapidly progressed in the AEC sector, resulting in a diverse literature landscape due to the various technologies and parameters involved in fully developing the DT technology. The intricate complexities inherent in digital twin advancements have confused professionals and researchers. This confusion arises from the nuanced distinctions between the two technologies, i.e., BIM and DT, causing a convergence that hinders realizing their potential. To address this confusion and lead to a swift development of DT technology, this study presents a holistic review of the existing research focusing on the critical components responsible for developing DT applications in the construction industry. The study identifies five crucial elements: technologies, maturity levels, data layers, enablers, and functionalities. Additionally, it identifies research gaps and proposes future avenues for streamlined DT developments and applications in the AEC sector. Future researchers and practitioners can target data integrity, integration and transmission, bi-directional interoperability, nontechnical factors, and data security to achieve mature digital twin applications for AEC practices. This study highlights the growing significance of DTs in construction and provides a foundation for further advancements in this field to harness its potential to transform built environment practices.

This article presents the development and validation of a new instrument measuring social, cultural, and behavioral factors influencing exposure to occupational zoonoses in agricultural settings. The Social Ecological Model (SEM) and the Standards for Educational and Psychological Testing were used as guiding frameworks to ensure the instrument's validity. The instrument's content was compiled by combining the results of a scoping literature review and an expert qualitative study. The instrument items were drafted, organized, and underwent a meticulous process of revision and adjustment. It was translated into Spanish and tested in one-to-one cognitive interviews with five volunteer agricultural workers. Exploratory factor analysis was conducted for construct discrimination, and bivariate regression analyses were conducted to explore the association with exposure indicators. Evidence of validity was obtained from four out of five sources of validity evidence according to the AERA/APA’s Standards of Educational and Psychological Testing. The Social Ecology of Occupational Zoonoses (SEOZ) was successfully used to determine social and behavioral factors associated with a higher risk of exposure to occupational zoonoses. Further use of the SEOZ can provide valuable insights into developing effective interventions to improve the health and well-being of agricultural workers.

Most of the municipalities in the Gulf region are facing performance related issues in their municipal solid waste management (MSWM) systems. They lack to possess a deliberate inter-municipality benchmarking processes. Instead of identifying the performance gaps for their key components (e.g., personnel productivity, operational reliability, etc.) and adopt proactive measures, the municipalities primarily rely on an efficient emergency response. A novel hierarchical modeling framework, based on deductive reasoning, is developed for performance assessment of MSWM systems. Fuzzy rule based modeling using Simulink-MATLAB was used for performance inferencing at different levels, i.e., component, sub-components, etc. The model is capable of handling the inherent uncertainties due to limited data and imprecise knowledge base. The model’s outcomes can exclusively assist the managers working at different levels of organizational hierarchy for effective decision-making. Performance of the key component, assists the senior management to assess the overall compliance level of performance objectives. Subsequently, operation management can hone in the sub-components to acquire useful information for intra-municipality performance management. While, individual indicators are useful for inter-municipality benchmarking. The model has been implemented on two municipalities operating in Qassim Region, Saudi Arabia. The results demonstrate the model’s pragmatism for continuous performance improvement of MSWM systems in the country and elsewhere.

Gas sensing is crucial for detecting hazardous gases in industrial environments, ensuring safety and preventing accidents. Additionally, it plays a vital role in environmental monitoring and control, helping to mitigate pollution and protect public health. Integrated photonic gas sensors are important due to their high sensitivity, rapid response time, and compact size, enabling precise recognition of gas concentrations in real-time. These sensors leverage photonic technologies, such as waveguides and resonators, to enhance performance over traditional gas sensors. Advancements in materials and fabrication techniques could further improve their efficiency, making them invaluable for environmental monitoring, industrial safety, and healthcare diagnostics. In this review, we delved into photonic gas sensors that operate based on the principles of evanescent field absorption (EFA) and wavelength interrogation methods. These advanced sensing mechanisms allow for highly sensitive and selective gas detection, leveraging the interplay of light with gas molecules to produce precise measurements.

The fourth industrial revolution has resulted in the digitalization of projects and operations across all sectors. Accordingly, efforts are being made to utilize advanced technologies to improve the energy efficiency of the building sector. This study has reviewed the current application and limitations of cutting-edge technologies in this regard. An overview of the use of the Internet of Things (IoT), artificial intelligence (AI), digital twin (DT), and building information modeling (BIM) for energy efficiency of buildings has been provided. It has been found that the use of Industry 4.0 technologies, during the construction and operational phase of buildings, has a great potential to reduce energy consumption and emissions of the sector. This study may help stakeholders of the built environment to understand the role of industry 4.0 tools for energy efficiency of the sector.

Biogeochemical models estimate soil organic carbon (SOC) sequestration, crop growth, and yield. The DeNitrification and DeComposition (DNDC) model was used to simulate soil SOC dynamics and harvested C-biomass in rice-wheat rotation under organic/inorganic fertilizations with conventional tillage (CT) and reduced tillage (RT). Before calibration, DNDC under-predicted harvestable grain C-biomass of rice by 29.22% to 42.14% and over-simulated grain C-biomass of wheat by 55.01% with equal amounts of NPK and animal manure applied under CT. However, after calibration by adjusting default values of soil/crop parameters, DNDC simulated harvestable grain C-biomass of both crops very close to observed values (only -2.81% to -6.17% less). DNDC also predicted effects of nutrient management practices on grain C-biomass of rice/wheat under CT/RT using d-index (0.76 to 0.96) and the calculated root mean squared error (RMSE of 165.36 to 494.18 kg C ha-1). DNDC simulated SOC trends for rice-wheat using measured values of several statistical indices. Regression analysis between modeled and observed SOC dynamics was significant with R2 ranging from 0.35 to 0.46 (p < 0.01), and intercept ranging from 0.30 to 1.34 (p < 0.65). DNDC demonstrated that combined inorganic and organic fertilization may result in higher C-biomass and more SOC sequestration in rice-wheat systems.

The efficiency of a new composite material of the layered double hydroxide (LDH) of ZnMgAl and rice husk biochar (RHB) for the removal of Cu(II) and Pb(II) ions from synthetic wastewater was investigated in this study. The images of scanning electron microscope showed extremely fine crystalline LDH particles decorated on the rough surface of the RHB while the succesful formation of the composite adsorbent (LDH/RHB) was confirmed by the corresponding energy dispersive X-ray and the Fourier-transform infrared spectroscopy. An equilibrium contact time of 30 and 15 min for Cu2+ and Pb2+, respectively, was proposed for the optimum performance of the batch adsorption process. The dose of the LDH/RHB adsorbent was optimized at 0.4 g yielding maximum adsorption capacities of 117 and 124 mg g-1 for Cu2+ and Pb2+, respectively, with corresponding maximum removal efficiencies of nearly 94% and 99%. The initial meta concentrations was optimized at 50 or 60 mg L-1 corresponding to maximum removal efficiencies or adsorption capacities. For the changing initial metal’s concentration, the removal efficiencies remained unchanged for up to 50 mg L-1 and decreased by about 50% by increasing the initial concentrations from 50 to 100 mg L-1. The adsorption capacities observed a linear increasing trend by increasing the initial concentrations from 5 to 60 mg L-1 and remained unchanged afterward up to 100 mg L-1. A solution pH of 6.0 yielded optimum results with an increasing trend in adsorption capacities and percentage removal by changing the solution pH from 2.0 to 7.0. Based on the best-fit of the pseudo second-order kinetic model to the experimental data, the chemisorption was suggested to be the controlling mechanism of adsorption. The fitting of the Langmuir model suggested a monolayer sorption of Cu2+ and Pb2+ in addition to a heterogeneous adsorption as supported by the fitting of the Temkin isotherm. The application of the Dubinin–Radushkevich isotherm proposed a physical adsorption (mean free energy of adsorption less than 8 kJ mol−1) of both heavy metal ions on the surface of the LDH/RHB adsorbent.

Bifenthrin is a synthetic pyrethroid insecticide. It is used worldwide against different agricultural pests. Nervous system (NS) is the primary target organ for the pyrethroid group of insecticide which causes hyper excitation. The aim of this study to determine the effects of bifenthrin on the brain of rabbits. The animals were treated for 14 days with three different doses (1/5th, 1/10th and 1/15th of LD50) of bifenthrin. Neurotransmitters and Histopathological alterations were observed at the end of the experiments. Neurochemical parameters were checked 24 hours after the last dose. Significant changes in the level of biogenic amines were observed. The levels of epinephrine (EPN), dopamine (DA), 3, 4 dihydroxyphenylacetic acid (DOPAC) were decreased as compared to controls group with the increase in insecticide. However, norepinephrine (NE) and homovanillic acid (HVA) levels were found to be significantly higher than those of the controls. A significant reduction in the activity of the acetyl cholinesterase enzyme was found in the frontal cortex’s erythrocyte, plasma and brain of rabbit with the increase in administered bifenthrin. The oxidative stress showed significantly decrease in the activity of glutathione peroxidase (GPx), superoxide dismutase (SOD), catalase (CAT) and glutathione S- transferase (GST) with the increase in dose of bifenthrin. Histopathological study of brain tissues showed normal GC (glial cells) and NC (neuronal cells) in the frontal cortex of brain tissue of control groups while the treated groups showed evacuation (odema), elongation of pyramidal nucleus, glial cell damage and brain haemorrhage.