This paper presents a novel normative framework for assessing granular base materials in rigid pavements, incorporating evaluations of California Bearing Ratio (CBR) alongside hydraulic conductivity tests. A critical component of this research adheres to Federal Highway Administration (FHWA) standards, which specify a permeability coefficient range of 0.05 to 0.20 cm/sec. Our investigations indicate that increased compaction energy inversely affects permeability, highlighting a sophisticated interplay between compaction dynamics and hydraulic characteristics. The study further elucidates that CBR values are profoundly impacted by the content of coarse-grained soil, advocating for a tailored approach to base layer assessment. Multivariable CBR analysis facilitated the identification of an optimal water content, underscoring that maintaining a minimum 80% CBR—while minimizing water content—can mitigate fatigue effects and enhance structural performance under heightened energy conditions. This research proposes bespoke, scientifically validated standards that integrate local geotechnical nuances, aimed at refining material selection processes and extending the durability of pavement infrastructures through foundational yet meticulous geotechnical evaluations.

The infections caused by Chikungunya virus (CHIKV), genus Alphavirus, have become a health problem around the world, due to this virus’s widespread occurrence and high morbidity rate and the absence of vaccines or antiviral drugs. In this study, we analyzed a competitive inhibitor of ornithine decarboxylase—an enzyme that is key in the biosynthesis of polyamines (PAs), N-ω-chloroacetyl-L-ornithine (NCAO), which is a possible inhibitor of CHIKV replication because intracellular polyamines participate in the in vitro transcription and translation of CHIKV. NCAO does not have any cytotoxic effect on C6/36 cells even at 1000 μM at 72 h post-exposure. However, in Vero cells, a cytotoxic effect was present above 380 μM at 48 h post-exposure, which was considered when determining the inhibitory effect on viral replication. In this work, we demonstrate that NCAO inhibits the replication of CHIKV in Vero and C6/36 cells in a dose-dependent manner, causing a decrease in the PFU/mL of at least 4 logarithms (p <0.01) in both cell lines. Viral yields were restored by the addition of exogenous polyamines, mainly putrescine. The HPLC analyses showed that NCAO decreases the content of intracellular PAs, even though mainly spermidines and spermines are present in infected cells. NCAO inhibits CHIKV replication by depleting the intracellular polyamines in Vero and C6/36 cells, suggesting that this compound is a possible antiviral for CHIKV infections.

The numerical simulation of entropy generation at mixed natural free and forced convection flow in a square lid-driven cavity filled with an eletrically conducting binary fluids saturated porous media in the presence of a magnetic field is performed in this investigation. Both the top and bottom horizontal walls of the cavity are kept at constant and different temperatures while the left and right vertical walls are adiabatic and insulated. The magnetic field is applied in normal direction to the cavity. The Darcy model, including Brinkman term relative to viscous effects and Forchheimer term due to inertial forces, is used for the momentum equations, and the SIMPLER algorithm, based on the control volume finite-element method approach is used to solve the pressure –velocity coupling. The flow pattern and the heat transfer characteristics inside the cavity are presented in the form of isotherms, streamlines and isentropic lines and average Nusselt number trend. The entropy generation rate is determined for various values of Darcy number (10^-3 ≤ Da ≤ 1) and for a range of Hartmann number (0 ≤ Ha ≤ 10²). This study is limited to Pr = 7 which corresponds to water. It is observed that entropy generation is very affected by the variations of dimensionless control parameters considered.

One of the most burning topics in cybersecurity in 2023 will undoubtedly be the compliance with the Software Bill of Materials. Since the US president issued the Executive Order 14028 on Improving the Nation’s Cybersecurity, software developers have prepared and bills are transmitted to vendors, customers, and users, but they don’t know what to do with the reports they are getting. In addition, since software developers have identified the values of the Software Bill of Materials, they have been using the reports extensively. This article presents an estimate of 270 million requests per month, just from form one popular tool to one vulnerability index. This number is expected to double every year and a half. This simple estimate explains the urgency for automating the process. We propose solutions based on artificial intelligence and machine learning, and we base our tools on the existing FAIR principles (Findable, Accessible, Interoperable, and Reusable). This methodology is supported with a case study research and Grounded theory, for categorising data into axis, and for verifying the values of the tools with experts in the field. We showcase how to create, and share Vulnerability Exploitability eXchange data, and automate the Software Bill of Materials compliance process with AI models and a unified computational framework combining solutions for the following problems: (1) the data utilisation problem, (2) the automation and scaling problem, (3) the naming problem, (4) the alignment problem, (5) the pedigree, and provenance problem, and many other problems that are on the top of mind for many security engineers at present. The uptake of these findings will depend on collaborations with government and industry, and on the availability and the ease of use of automated tools.

This study investigates the permeability and California Bearing Ratio (CBR) of base course materials for flexible pavements, focusing on materials from local quarries in Querétaro and Puebla, Mexico. Recognizing the fundamental role of the base layer in load distribution and hydraulic conductivity, the research evaluates these properties at different grain sizes and moisture contents. The objective is to define an optimal range that maximizes both drainage and mechanical resistance, crucial to extending the useful life of the pavement. Four different quarries were selected for material sampling and extensive testing was performed to determine permeability and CBR values under different conditions. The findings reveal the need for broader experimentation and methodological improvements, particularly in the measurement of hydraulic conductivity, a parameter not yet regulated for these materials in Mexico. The results demonstrated permeability values ranging between 1.2810^-3 and 1.9010^-3 cm/s, highlighting the significant impact of the percentage of fine material and its plasticity on the hydraulic and mechanical performance. Despite achieving permeability rates lower than the optimal value suggested in American manuals (0.35 cm/s), even with a fine material content of less than 5%, the study highlights the potential of local materials to meet the international standards with proper processing and testing. This research contributes to the global body of knowledge in pavement engineering by linking local geomaterial properties to broader applicable engineering practices. It suggests that even locally sourced materials, when appropriately evaluated and used, can significantly influence overall pavement solutions, promoting sustainability and cost-effectiveness in pavement construction.

The proliferation of devices for the Internet of Things (IoT) and their implication in many activities of our lives have led to a considerable increase in concern about the security of these devices, posing a double challenge for designers and developers of products. On the one hand, the design of new security primitives, suitable for resource-limited devices, that can facilitate the inclusion of mechanisms and protocols to ensure the integrity and privacy of the data exchanged over the Internet. On the other hand, the development of techniques and tools to evaluate the quality of the proposed solutions as a step prior to their deployment, as well as to monitor their behavior once in operation against possible changes in operating conditions arising naturally or as a consequence of a stress situation forced by an attacker. To address these challenges, this paper first describes the design of a security primitive that plays an important role as a component of a hardware-based root of trust, as it can act as a source of entropy for true random number generation (TRNG) or as a physical unclonable function (PUF) to facilitate the generation of identifiers linked to the device on which it is implemented. The work also illustrates different software components that allow carrying out a self-assessment strategy to characterize and validate the performance of this primitive in its dual functionality, as well as to monitor possible changes in security levels that may occur during operation as a result of device aging and variations in power supply or operating temperature. The designed PUF/TRNG is provided as a configurable IP module, which takes advantage of the internal architecture of the Xilinx Series-7 and Zynq-7000 programmable devices and incorporates an AXI4-based standard interface to facilitate its interaction with soft- and hard-core processing systems. Several test systems that contain different instances of the IP have been implemented and subjected to an exhaustive set of on-line tests to obtain the metrics that determine its quality in terms of uniqueness, reliability, and entropy characteristics. The results obtained prove that the proposed module is a suitable candidate for various security applications. As an example, an implementation that uses less than 5% of the resources of a low-cost programmable device is capable of obfuscating and recovering 512-bit cryptographic keys with virtually zero error rate.

In this paper, we introduce a new class of open sets that is called is*-open set . Also, we present the notion of is*-continuous, is*-open, is*-irresolute, is*-totally continuous, and is-contra-continuous mappings, and we investigate some properties of these mappings. Furthermore, we introduce some is*-separation axioms, and is*-mappings are related with is*-separation axioms. . .

The diagnosis and treatment of autoimmune diseases are major challenges. Their signs, symptoms, and their clinical severity change throughout the course of the disease. The available treatments for these conditions do not result in complete remission, and their long-term use generates several side effects. The main challenges in this field are the development of more sensitive diagnostic tools, and effective treatments. Studies in patients and animal models reported alterations in monocyte phenotype, activation, and function. These cells play an essential role in the pathogenesis of chronic inflammatory states and have become a target for extracorporeal monitoring and specific intervention. Nanoparticles (NPs) are ultrafine particles that can be used as contrast agents in diagnostic imaging techniques to detect specific cells in inflammatory infiltrates in tissues that are not easily accessible by biopsy. In addition, NPs can be designed to deliver drugs to a cell population or tissue. This review describes several experimental pieces of evidence demonstrating that monocytes and macrophages can specifically uptake various types of NPs, thus becoming detectable in vivo by magnetic resonance imaging and susceptible to be modulated by therapeutic agents. Hence, nanoparticles targeting mononuclear phagocytes represent promising tools for diagnosing and treatment.

Generation of unique identifiers extracted from the physical characteristics of the underlying hardware ensures the protection of electronic devices against counterfeiting and provides security to the data they store and process. This work describes the design of an efficient Physical Unclonable Function (PUF) based on the differences in the frequency of Ring Oscillators (ROs) with identical layout due to variations in technological processes involved in the manufacture of the integrated circuit. The logic resources available in the Xilinx Series-7 programmable devices are exploited in the design to make it more compact and achieve an optimal bit-per-area rate. On the other hand, the design parameters can also be adjusted to provide a high bit-per-time rate for a particular target device. The PUF has been encapsulated as a configurable Intellectual Property (IP) module, providing it with an AXI4-Lite interface to ease its incorporation into embedded systems in combination with soft- or hard-core implementations of general-purpose processors. The capability of the proposed RO-PUF to generate implementation-dependent identifiers has been extensively tested, using a series of metrics to evaluate its reliability and robustness for different configuration options. Finally, in order to demonstrate its utility to improve system security, the identifiers provided by RO-PUFs implemented on different devices have been used in a Helper Data Algorithm (HDA) to obfuscate and retrieve a secret key.

This work presents a new model to obtain the minimum cost design for a rectangular isolated footing, taking into account that the column is located in any part of the footing. The methodology is developed by integration to obtain the moments, bending shear and punching shear according to the American Concrete Institute ACI 318-14. This document presents the simplified and precise equations of the four moments, four bending shears and one punching shear acting on the footing. Some designs have been developed by the trial and error method to determine the footing dimensions, and later the thickness and steel area of the footing are obtained. Some authors present the minimum cost design for a rectangular isolated footing taking into account that the column is located in the center of gravity of the footing, and other authors present very complex algorithm. Numerical examples are presented to obtain the minimum cost design of rectangular isolated footings under biaxial bending, and some results are compared with those of other authors considering the same conditions. The new model presents a smaller contact area with the soil and a lower design cost than those presented by other authors.

This paper shows the influence of CCP’s collateralization on the pricing of the Credit Default Swaps (CDS). A narrowly variant in the way the CDS seller decides over the resources in the settlement comes with a substantial change on the elements that determine the price of the CDS.

The information on the land use and soil conservation practice based on year 2006, 2010 and 2014, hence offering an opportunity to model the impacts of land use change on erosion, deposition and surface water runoff. Limitation in the use of hydrological models had been their inability to handle the large amount of input data that describe the heterogeneity of the natural system. In this study, a procedure that takes into account soil conservation practice based on the land use change, the response of soil erosion and sediment export from the George Town Conurbation catchment area, and average annual sediment yields were estimated for each grid cell of the watershed to identify the critical erosion areas of rural and urban planning proposes. Average annual sediment yield and data on a grid basis estimated using Universal Soil Loss Equation (USLE) and an emerging technology represented by Geographic Information System (GIS) used as a tool to produce a map for erosion rate. The changing of the land use from forest to agriculture and then to an urban area is a challenging task to research on land use demand for population, and environmental impact assessment is important for the planning of natural resources management, allowing research the modification of land use properly and implement more sustainable for long term management strategies. The challenge is to formulate strategies that would promote an integrated approach to the land use planning at an appropriate level as to address the issues that arose. Modelling for creating urban growth boundary for the George Town Conurbation must have to be controlled surface runoff and soil loss and sediment export from land use of the George Town Conurbation catchment.

Pterygium is a common ocular disease caused by abnormal cellular proliferation leading to abnormal fibrovascular growth of the conjunctiva. The main treatment is surgical removal; however, despite the improvement of surgical techniques and development of adjuvant therapies, postoperative recurrence, which can be as high as 89%, remains a challenge. Currently, pterygium excision with conjunctival autograft remains the preferred surgical technique to decrease recurrence, especially when combined with ciclosporin eye drops. Nevertheless, there is no gold standard surgical technique to prevent pterygium recurrence. Therefore, this review aims to assess the safety, effectiveness and, applicability of platelet-rich fibrin membrane for primary pterygium surgery and assess its possible benefits in resource-limited settings.

The development of sustainability, the improvement of the quality of life, and the protection of future generations have become of prime importance in light of climate changes and carbon emissions. Universities are at the top of institutions that should participate in creating an environmentally friendly infrastructure. This study thus aimed to explore the extent to which Saudi universities achieve sustainability in the light of the Saudi Green Initiative from the faculty members’ perspective. Surely, this investigation would produce a proposal to promote sustainability in Saudi universities. A questionnaire consisting of five dimensions, namely academic sustainability, community partnership, resource management, planning and administration, and innovation and leadership was developed and administered to 120 faculty members from five Saudi universities. The participants’ ratings of Saudi universities’ achievement of sustainability dimensions ranged from high to moderate. Based on the results, a proposal was offered to take sustainability in Saudi universities to a higher level.

Mental Disorders are an important public health problem. The main of this study was to analyze the prevalence of Mental Disorders and Environmental Quality. Data on the Prevalence of Mental Disorders, Gross Domestic Product, and Median Years of Schooling from 178 countries were used. A positive association was observed and was independent of Gross Domestic Product and Median Years of Schooling.

The steep rise in reinforcement learning (RL) in various applications in energy as well as the penetration of home automation in recent years are the motivation for this article. It surveys the use of RL in various home energy management system (HEMS) applications. There is a focus on deep neural network (DNN) models in RL. The article provides an overview of reinforcement learning. This is followed with discussions on state-of-the-art methods for value, policy, and actor–critic methods in deep reinforcement learning (DRL). In order to make the published literature in reinforcement learning more accessible to the HEMS community, verbal descriptions are accompanied with explanatory figures as well as mathematical expressions using standard machine learning terminology. Next, a detailed survey of how reinforcement learning is used in different HEMS domains is described. The survey also considers what kind of reinforcement learning algorithms are used in each HEMS application. It suggests that research in this direction is still in its infancy. Lastly, the article proposes four performance metrics to evaluate RL methods.

Due to the retrognathic mandible, an orthodontist frequently observes skeletal class II malocclusion in growing patients. The preferred technique for analyzing and monitoring the temporomandibular joint alterations caused by the functional device is magnetic resonance imaging [MRI]. The study aimed to assess and compare changes in the articular disc's dimension and location before and following the use of various class II correctors to correct the class II molar relation using MRI technology. Methods: 39 adolescent patients aged 15-23 years old [24 girls and 15 boys] who were diagnosed with skeletal Class II division 1 malocclusion based on clearly defined criteria underwent treatment with either the power scope II [PS], Sabbagh Advanced Repositioning Appliance [SARA] and or Dynaflex [DF] with fixed appliances. For fixed functional treatment, the average length of treatment was 5-7 months. The changes in the articular disc dimension and position and condylar position were assessed. The study was done at the Department of Orthodontics at the College of Dentistry, Hawler Medical University in Erbil City. Results: Group DF has a significant effect on the condylar position index and posterior joint space on the closed mouth and disc length on both open and close mouth techniques, and in the group SARA, disc position, and condylar position index on closed mouth technique have shown that significant differences were observed. Conclusion: Class II malocclusions can be effectively corrected by fixed functional appliances. The statistical significance forward movement of the condyle in the glenoid fossa and the posterior movement of the articular disc concerning the condylar head was observed. The mechanism of action of functional appliances appears to include the forward migration of the C-GF complex.

The aim of this paper is to create a sensor model based on optical crystal fibers (PCF). The aim of this model is to find and identify zinc cadmium. This thesis looked at three different categories of concentrations. For sensor architecture, PCF was generated using single-mode fiber-to-end split fusion (SM-PCF-SM). In this experiment, a specific wavelength spectrum was used to alter the concentration of materials covering the fiber in order to demonstrate the fiber's sensing capability. The 550nm wavelength has been used as the optical source for the fiber. The change in the output power of the external light was monitored and changes were observed for each concentration of the concentrations around the fiber. It has been found that the fiber is sensitive to small changes in concentrations. The absorption of the fiber has been calculated for the incoming capacity, as well as the losses in the capacity outside the fiber.

Immune checkpoint inhibitors (ICIs) – anti-programmed death-1 (PD-1) and their ligands (PD-L1 and PD-L2) have become widely used in the treatment of several malignancies. Many immune-related adverse events have been linked to these agents. However, tuberculosis (TB) reactivation during their use is increasingly reported. Herein, we present a 58-year-old lady with advanced non-small cell lung cancer (NSCLC) ALK-negative, EGFR wild, and PD-L1 Immune histochemistry (IHC) strongly positive in 95% of tumor cells. The patient presented with high-grade fever and a history of productive cough for a 1-week duration. A few days later, she was diagnosed with pulmonary tuberculosis following the 6th cycle of Pembrolizumab, an anti-PD-1 monoclonal antibody. AFB smear and TB PCR from BAL were positive (rifampin resistance not detected), and she was accordingly started on Anti-TB medications. Immunotherapy was held. Of note, the patient had a history of sick contact with a patient with active TB infection ten years ago, but there was no documentation of latent TB or previous TB infection. Her HIV status is negative. Her sputum AFB smear continued to be positive after four weeks of anti-TB medications. Later, the patient was discharged after her sputum was cleared from AFB (negative x 2 sets). We assumed that our patient developed reactivation of pulmonary tuberculosis secondary to an immune checkpoint inhibitor (Pembrolizumab). She was not re-challenged with Pembrolizumab following TB diagnosis. To our knowledge, this is the first reported case from the Arab and the Middle East; it reinforces the previous observations of the association between ICIs administration and the development of MTB. Nevertheless, further studies in the clinical setting are necessary to establish the exact mechanism involved in this association. Oncologists' awareness & prompt recognition of this potential hazardous consequence are essential. Since there is no clear evidence whether LTBT prior PD-1/PD targeted immunotherapy is required, targeted LTBT before starting ICIs immunotherapy with TB chemoprophylaxis; yet to be explored, particularly in the regions where the MTB prevalence is high.

We propose a class of stochastic models for a dynamics of limit order book with different type of liquidities. Within this class of models we study the one where a spread decreases uniformly, belonging to the class of processes known as a population processes with uniform catastrophes. The law of large numbers (LLN), central limit theorem (CLT) and large deviations (LD) are proved for our model with uniform catastrophes. Our results allow us to satisfactorily explain the volatility and local trends in the prices, relevant empirical characteristics that are observed in this type of markets. Furthermore, it shows us how these local trends and volatility are determined by the typical values of the bid-ask spread. In addition, we use our model to show how large deviations occur in the spread and prices, such as those observed in flash crashes.

Advanced Hepatocellular carcinoma (HCC) is no longer a terminal illness. This change was mainly attributed to the development of new treatments including tyrosine-kinase inhibitors (TKIs), vascular endothelial growth factor (VEGF) inhibitors and immune checkpoint inhibitors (ICPIs) but the financial toxicity of treating advanced HCC is of a major concern specially in low middle-income countries (LMICs) where the patients are still battling for their most basic rights. Most of advanced HCC patients in LMICs have very limited accessibility to the new treatments including ICPIs. Searching for out of the box solutions to improve access to treatments -mainly ICPIs- is an utmost necessity for LMICs advanced HCC patients.

Background: Coronavirus disease (COVID-19) is an infectious disease caused by the SARS-CoV-2. In Colombia, many commercial methods are now available to perform the RT-qPCR assays, and the laboratories must evaluate its diagnostic accuracy to ensure reliable results to suspected COVID-19 patients. The purpose of the study was to compare four commercial RT-qPCR assays for detection of SARS-CoV2 virus, from nasopharyngeal swab samples referred to Laboratorio Carvajal IPS, SAS of Tunja, Boyacá - Colombia. Methods: This prospective study was conducted on 152 samples of respiratory tract samples (Nasopharyngeal Swab) from patients with suspected SARS-CoV-2 infection. Diagnostic accuracy of GeneFinderTM COVID-19 Plus RealAmp (In Vitro diagnostic), One-Step Real-Time RT-PCR (Vitro Master diagnostica), Berlin modified protocol and gold standard Berlin protocol (Berlin Charite Probe One-Step RT-qPCR Kit, New England Biolabs) as reference was assessed. Operational characteristics were estimated in terms of sensitivity, specificity, agreement, and predictive values. Results: Using Berlin Charite Probe One-Step RT-qPCR Kit as reference, the sensitivity/specificity for the diagnostic tests were found to be GeneFinderTM COVID-19 Plus RealAmp Kit 100%/92.7%, One-Step Real-Time RT-PCR, One-Step Real-Time RT-PCR 92.75%/67.47%, and Berlin modified protocol 100%/96.39%. The results of four commercially available methods were found to be consistent with those obtained from Berlin Modified protocol analysis for % of the samples and showed good agreement (κ= 0.96). Concordant SARS-CoV2 negative and positive RT-qPCR results were reported for xxx and xxx samples, respectively. Summarize something about the Ct. Conclusion: Our data demonstrate that all commercially available methods are rapid and reliable for the identification of SARS-CoV-2 virus associated with COVID-19. One-Step RT-qPCR Kit and GeneFinderTM COVID-19 Plus RealAmp assay show optimal sensitivity compared with Belin modified protocol. In addition, there is no significant correlation between xxxxx

Colistin [polymyxin E] is a veterinary exclusive antimicrobial and one of the oldest antibiotics that is currently recognised as one of the highest priority critically important antimicrobials for humans. It is extensively used for multiple medical and non-medical purposes particularly for growth promotion, prophylaxis/metaphylaxis and therapeutic in food animals. As a result, colistin resistance was widespread along the food-chain linking to multidrug resistant bacterial infections in humans reflected by greater use of colistin in healthcare settings resulted in different types of bans/restrictions in food-producing animals, around the world. This report debates the testimonies of 23 countries representing the bulk of global food producing animal production, providing robust evidence on the essential need for colistin in animal production.

Flooding, exacerbated by climate change, poses a significant threat to certain areas, increasing in frequency and severity. In response, the construction of supplementary dams has emerged as a reliable solution for flood management. This study employs a Remote Sensing (RS) approach integrated with GIS to assess the feasibility of constructing a supplementary dam near Linville, Brisbane, Australia, with the aim of mit-igating floods and preventing overtopping failure at the Wivenhoe Dam. Using QGIS software and a 25-meter resolution DEM from the Queensland Spatial Catalogue ‘QSpatial’ website, four potential dam sites were analysed, considering cross-sections, watershed characteristics, and water volume calculations. Systematic selection criteria were applied to identify the most optimal option based on dam wall di-mensions, volume-to-area, and volume-to-cost ratios. The selected option was further assessed against predefined criteria, yielding one optimal choice. The study provides insights into the feasibility and ef-fectiveness of supplementary dam construction for flood mitigation in the region, with recommendations for future research and implementation.

Urban and agricultural runoffs can transport contaminants and pesticides into freshwater ecosystems, particularly in the developing tropics. For instance, organophosphate and pyrethroids pesticides like glyphosate, malathion, and permethrin have been found in tropical streams. The uncontrolled application of these pesticides has become a growing concern due to their adverse effects on various non-targeted organisms. Unfortunately, most studies have focused on a few selected model species, ignoring the effects on other nontarget organisms, which may play an important role in tropical lotic ecosystems. In addition, the biological characteristics of aquatic crustaceans, including their morphology, physiology, and behavior, make them susceptible to toxic chemicals. For this reason, this study used the widely distributed freshwater shrimp Xiphocaris elongata as a model organism to determine the acute toxicity of permethrin, malathion, and glyphosate. Our results show that the proportion of mortality of X. elongata in each concentration group became progressively higher as the concentration of exposure increased. We also found that the synthetic pyrethroid permethrin is the most toxic pesticide tested, followed by organophosphate malathion and glyphosate. Experiments with this freshwater shrimp showed a good control performance and reproducibility for the tested pesticides. This study demonstrated that X. elongata is a suitable test organism that can be a representative bioindicator of pesticide toxicity in tropical streams.

Aptamers are synthetic single stranded oligonucleotides that exhibit selective binding properties to specific targets, thereby providing as powerful basis for the development of selective and sensitive (bio)chemical assays, such as biosensors. Electrochemical biosensors, utilizing aptamers as biological recognition elements, namely aptasensors, are at the forefront of current research. They exploit the combination of the unique properties of aptamers with the advantages of electrochemical detection with the view to fabricate inexpensive and portable analytical platforms for rapid detection in point-of-care (POC) applications or on-site monitoring. The immobilization of aptamers on suitable substrates is of paramount importance with the aim to retain their functionality and optimize the sensors’ sensitivity. This work describes different immobilization strategies for aptamers on the surface of semiconductor-based working electrodes, including metal oxides, conductive polymers and carbon allotropes. These are presented as platforms with tunable band gaps and different surface morphologies for the preparation of low cost, highly versatile aptasensor devices in analytical chemistry. A survey of the current literature is provided, discussing each analytical method. Future trends envisage for aptamer-based biosensing using semiconductors are also outlined.

In this paper a more flexible extension of the Fréchet distribution is introduced. The new distribution is defined by means of the stochastic representation as the quotient of two independent random variables, a Fréchet distribution and the power of a random variable with uniform distribution in the interval (0,1). We will call this new extension the Slash Fréchet distribution and one of its main characteristics is that its tails are heavier than the Fréchet distribution. The general density of this distribution and some basic properties are determined. Its moments, skewness coefficients and kurtosis are calculated. In addition, the estimation of the model parameters is obtained by the method of moments and maximum likelihood. Finally, two applications with real data are performed by fitting the new model and comparing it with the Fréchet distribution.

This article presents a forecast model that uses a hybrid architecture of recurrent neural networks (RNN) with surface neural networks (ANN), based on historical records of exported active energy (EAE) and weather data. Two types of models were developed: the first type includes six models that use EAE records and weather variables as inputs, while the second type includes eight models that use only weather variables. Different metrics were applied to assess the performance of these models, and the best model of each type was selected. Finally, a comparison of the performance between the selected models of both types is presented, and they are validated with real data provided by a solar plant, achieving acceptable levels of accuracy. The selected model of the first type has an RMSE of 0.19, MSE of 0.03, MAE of 0.09, a correlation coefficient of 0.96, and a determination coefficient of 0.93. The other selected model of the second type showed lower precision in the metrics (RMSE = 0.24, MSE = 0.06, MAE = 0.10, Corr. Coef. = 0.95, and Det. Coef. = 0.90). Both models demonstrated good performance and acceptable accuracy in forecasting the weekly photovoltaic energy production of the solar plant.

The participation of civil society is essential for environmental health policies to be effective. The objective of this study was to know the perceptions of government officials, members of civil society, and academics about environmental health problems and its governance in Bucaramanga Metropolitan Area, Colombia. In the region there is a strong citizen movement that defends the moorland ecosystem (paramo) as source of drinking water, of large-scale mining projects. A multi-method study was carried out including the review of newspaper and scientific articles, a citizen survey, and interviews and focus groups with identified key stakeholders. The findings indicate that government officials prioritize their actions on issues related to air and water pollution and environmental education. In contrast, citizens prioritize water availability from the moorland ecosystem. There are some advances in the management of environmental health, mainly related to greater citizen awareness. The participation of civil society in the environmental health governance must be enforced to broaden the issues of interest and prioritize the activities in the short- and long-term policy planning. An experience between high school students and the academy that measures air pollutants can be the first meeting point with government officials in the pathway to improve the environmental governance in the territory.

Cytochrome P450 oxidoreductase (POR) is the redox partner of steroid and drug-metabolizing cytochromes P450 located in the endoplasmic reticulum. Mutations in POR cause a broad range of metabolic disorders. The POR variant rs17853284 (P228L) identified by genome sequencing has been linked to lower testosterone levels and reduced P450 activities. We expressed POR wild type and the P228L variant in bacteria, purified the proteins, and performed protein stability and catalytic functional studies. Variant P228L affected the stability of the protein as evidenced by lower unfolding temperatures and higher sensitivity to urea denaturation. A significant reduction of small molecule metabolism was observed with POR P228L while activities of CYP3A4 were reduced by 25%, and activities of CYP3A5, and CYP2C9 were reduced by more than 40% compared to WT POR. The 17,20 lyase activity of CYP17A1 responsible for production of main androgen precursor dehydroepiandrosterone, was reduced to 27% of WT in presence of P228L variant of POR. Based on in silico and in vitro studies we predict that the change of proline to leucine may change the rigidity of the protein, causing conformational changes in POR, leading to altered electron transfer to redox partners. A single amino acid change can affect protein stability and cause a severe reduction in POR activity. Molecular characterization of individual POR mutations is crucial for a better understanding of the impact on different redox partners of POR.

Floods are the most frequent and devastating disasters in Bangladesh. The riverine islands, known as char-lands, are particularly vulnerable to flooding. As flooding poses a significant threat to the lives and livelihoods of residents, especially farmers, it is crucial to understand how they perceive flood risk and assess their adaptation strategies in this geographically susceptible context. However, the existing literature has not adequately addressed these issues. Therefore, this study aims to analyze the factors influencing farmers' perceived flood risk and their assessments of flood adaptation. In a survey of 359 farmers in Bangladesh's char-land region, located in the Chowhali sub-district of Sirajganj district, we used the protection motivation theory (PMT) to measure farmers' perceived flood risk and adaptation assessments. Multiple regression analysis was employed to identify factors influencing them. Farmers prioritized the risk to livelihoods (production and income) over psychological aspects (health and diseases). Larger farms, more flood experience, and greater risk awareness are associated with higher overall flood risk perception; and better flood adaptation, indicating higher self-efficacy, response efficacy, and response cost among farmers. Farmers perceived lower flood risk in exchange for greater house distance from the river and more trust in government actions. Hence, strengthening campaigns and programs is crucial to understanding flood risk in char-lands for improved adaptation to floods. The study highlights the application of PMT to assess farmers' perceptions of flood risk and their attitudes towards adaptation, suggesting further research opportunities.

Based on economic feasibility, renewable generators can use pumped hydro storage (PHS) to improve their profitability by performing energy arbitrage under real time pricing (RTP) schemes. In this paper, we present a new method to optimise the size and manage utility-scale wind-PV systems using PHS with energy arbitrage under RTP. The storage in the PHS is used to supply load consumption and/or energy arbitrage. Further, both load supply and power-generating systems are considered, and a genetic algorithm metaheuristic technique is used to perform the optimisation efficiently. Irradiance, wind speed, temperature, hourly electricity price, component characteristics, and financial data are used as data, and the system is simulated in 15 min time steps during the system lifetime for each combination of components and control variables. Uncertainty is considered for the meteorological data and electricity prices. The pump and turbine efficiencies and available head and penstock losses are considered as variables (not fixed values) to obtain accurate simulations. A sample application in Spain is demonstrated by performing a sensitivity analysis of different locations, electricity prices, and costs. The PHS is not worth considering with the present cost of components.

Robotic surgery is a rapidly developing and evolving surgical technique. This literature review evaluates the advantages and disadvantages in the context of gallbladder disease comparing robotic Cholecystectomy to the well-established laparoscopic Cholecystectomy. Significant advantages are reduced operative blood loss, hospital stays and post operative pain, alongside increased patient satisfaction and improved visualization and precision compared to the laparoscopic approach. Disadvantages include lack of tactile feedback, significant cost attributed to equipment, training requirements and increased procedural time due to the set-up sequences. The implementation of robotic surgery also poses significant changes for the training of future surgeons. Whilst it can standardize training and increases opportunity for simulation, the concern is the loss of traditional skills. Currently the evidence base remains mixed however the use of robotics in the right setting, with suitably trained operatives and appropriate patients can enable improved outcomes for patients with gallbladder disease. There is a lot of scope for development including the implementation of tactile feedback to aid operative technique and artificial intelligence to aid patient safety. Likely broadening the use and potential benefit of robotic surgery not only for cholecystectomy but many surgical specialties.

Advances in early detection of Breast cancer and treatment improvements have significant-ly increased survival rates. Traditional screening methods, including mammography, MRI, ultrasound, and biopsies, while effective, often come with high costs and risks. Recently, thermal imaging has gained attention due to its minimal risks compared to mammography, although it is not widely adopted as a primary detection tool since it depends on identifying skin temperature changes and lesions. The advent of machine learning (ML) and deep learning (DL) has enhanced the effectiveness of breast cancer detection and diagnosis using this technology. In this study a novel methodology for developing an interpretable computer-aided diagnosis (CAD) system for breast cancer detection, leveraging explaina-ble Artificial Intelligence (XAI) throughout its various phases. To achieve these goals, we proposed a new multi-objective optimization approach named Hybrid Particle Swarm Optimization algorithm (HPSO) and Hybrid spider Monkey Optimization algorithm (HSMO). These algorithms simultaneously combine the continuous and binary representations of PSO and SMO to effectively manage trade-offs between Accuracy, feature selection and hyperparameter tuning. We evaluate several CAD models and investigate the impact of handcrafted methods such as Local Binary Patterns (LBP), Histogram of Oriented Gradients (HOG), Gabor filters, and edge detection. We further shedding light on the effect of feature selection and optimization on feature attribution and model decision-making processes using the SHapley Additive exPlanations (SHAP) framework, with a particular emphasis on cancer classification using the DMR-IR dataset. The results of our experiments demonstrate in all trials that the performance of the model is improved. Also with HSMO our models achieved a high accuracy of 98.27% and F1- score of 98.15% while selecting only 25.78% of the HOG features. This approach not only boosts the performance of CAD models but also ensures comprehensive interpretability. This method emerges as a promising and transparent tool for early breast cancer diagnosis.

Cytochrome P450 oxidoreductase (POR) is an essential redox partner for steroid and drug-metabolizing cytochromes P450 located in the endoplasmic reticulum. Mutations in POR lead to metabolic disorders, including congenital adrenal hyperplasia, and affect the metabolism of steroids, drugs, and xenobiotics. In this study, we examined approximately 450 missense variants of the POR gene listed in the Genome Aggregation Database (gnomAD) using eleven different in silico prediction tools. We found that 64 novel variants were consistently predicted to be disease-causing by most tools. To validate our findings, we conducted population analysis and selected two variations in POR for further investigation. The human POR wild type, along with the R268W and L577P variants, were expressed in bacteria and subjected to enzyme kinetic assays using model substrate. We also examined the activities of several cytochrome P450 proteins in the presence of POR (WT or variants) by combining P450 and reductase proteins in liposomes. We observed a decrease in enzymatic activities (ranging from 35% to 85%) of key drug metabolizing enzymes, supported by POR variants R288W and L577P compared to WT-POR. These results validate our approach of curating a vast amount of data from genome projects and provide an updated and reliable reference for diagnosing POR deficiency.

Prevalence of overweight and obesity are escalating globally among the general population. However, there are limited evidence on the trends and prevalence of overweight /obesity in the military setting. Increased rates of injuries, low work productivity, incurred higher healthcare costs and prematurely discharge from service are consequences of overweight/obesity among the military. Therefore, we aimed to systematically describe the trends and prevalence of overweight and obesity in the military population, by regions and military service branches. Databases including PubMed, Scopus, Web of Science and Google Scholar were used. Inclusion criteria were military population (inclusive of all service branches) with BMI reported as the overweight/obesity indicator. Population related to military but not exclusively military personnel such as the retirees, the veterans and their dependents were excluded. From the 27 included studies, 13 were published between year 2010 to 2014 and half were conducted in the United States. Overall, studies showed increasing trend in the prevalence of overweight (30% to 50%) and obesity (2% to 30%); only one study showed a decreasing trend of 0.9% and 0.6% for the prevalence of overweight and obesity respectively. However, the rates of increment differed between countries, where Asian countries demonstrated lower overweight prevalence compared to the United States and the European countries. In conclusion, the military population is not protected from overweight and obesity. Interventions should be implemented to prevent overweight / obesity among the military personnel.

The energy sector plays an important role in Mexico’s development trajectory. Mexico makes an interesting case study, because it shows how difficult it is to reduce fossil energy dependence despite geographic and climatic conditions that favour renewable energy deployment and use. Resolving path dependencies and the related carbon lock-in are key to Mexico’s sustainable energy transition. This case study aims to identify and discuss how carbon lock-in affects Mexico’s sustainable energy transition. Mexico’s carbon lock-in involves oil and oil-run power plants that are costly to build but relatively inexpensive to operate. This case study identifies potential entry points for transitioning towards sustainable energy in Mexico – resources that can promote the use of clean energy despite carbon lock-in. For example, focusing on electrification – particularly of the carbon-intensive sectors – can help Mexico transit towards sustainable energy despite institutional constraints. Complementing this case study is a teaching guide with recommendations for using Mexico’s energy transition in courses on sustainability. It introduces a “learning activation framework” to identify emerging opportunities that can advance sustainable energy transitions in different cases of carbon lock-in. Finally, the framework also gives students a chance to help dismantle or cope with carbon lock-ins.

This paper reports on the fabrication of alumina doped preforms using MCVD-vapor phase chelate delivery system with Al(acac)3 as the precursor. The objectives of the work are to study the deposition process, the efficiency of the fabrication process, and the quality of the fabricated fiber preforms. Two parameters are studied, Al(acac)3 sublimator temperature (TAl°C) and deposition direction (i.e. downstream and upstream). Other parameters such as oxygen flow and deposition temperature are fixed. The results showed that a high uniformity of refractive index difference (%RSD &lt; 2%) and core size (%RSD &lt; 2.4%) was obtained along the preform length using downstream deposition while for the combined upstream and downstream deposition the uniformity was deteriorated. The process efficiency was found to be about 21% for TAl°C of 185°C and downstream deposition. From the EDX elemental analysis, the refractive index was found to increase by 0.0025 per mole percent of alumina.

This research paper presents a new test based on a novel approach for identifying clustered graphical passwords within the Passpoints scenario. Graphical authentication methods serve as a viable alternative to the conventional alphanumeric password-based authentication method, which is susceptible to known weaknesses arising from user-generated passwords of this nature. The test proposed in this study is based on estimating the distributions of the perimeter of the convex hull. This perimeter is calculated based on the points users select as passwords within an image measuring 1920 × 1080 pixels. The test is formulated once the optimal theoretical distributions that fit the data are identified. Evaluating the proposed test’s effectiveness involves estimating type I and II errors. In this study, we compare the effectiveness and efficiency of the proposed test with existing tests from the literature that can detect this type of pattern in Passpoints graphic passwords. Our findings indicate that the new test demonstrates a significant improvement in effectiveness compared to previously published tests. Furthermore, the joint application of the two tests also shows improvement. Depending on the significance level determined by the user or system, the enhancement results in a higher detection rate of clustered passwords, ranging from 0.1% to 8% compared to the most effective previous methods. This improvement leads to a decrease in the estimated probability of committing a type II error. In terms of efficiency, the proposed test outperforms several previous tests; however, it falls short of being the most efficient. It can be concluded that the newly developed test demonstrates the highest effectiveness and the second-highest efficiency level compared to other tests available in the existing literature for the same purpose.

We propose a conceptual model for the closeness parameter $\epsilon$, which characterizes exotic compact objects (ECOs). To estimate $\epsilon$, a thin spherical dust shell is considered, which gravitationally contracts from a specific position $r(t_{0})$ to near its gravitational radius $r(t_{2})=r_{s} + \epsilon$, in a finite time $t_{2}$, measured in the frame of a fiducial observer (FIDO). For an external observer, the shell’s kinematics is characterized by two clearly distinguishable phases: one of rapid contraction, where the shell is far away from the gravitational radius, $r(t_{0})\gg r_{s}$, and a second phase quasi-stationary, $r(t)\sim r_{s}$, where all of the shell’s mass is concentrated around the associated horizon, such that for a FIDO, a black hole (BH)is undistinguishable from a shell configured as a black shell (BS). \\ In the semi-classical approximation $E\ll \kappa_{0}l_{p}^{2}$ and tends to zero when the observation time of collapse $t_{2}$, measured by FIDO, tends to infinity; $\kappa_{0}$ and $l_{p}$ are surface gravity and Planck length, respectively. The quantum effects are significant when $\epsilon\ll r(t_{2})$ and $\epsilon$ tends to $\kappa_{0}l_{p}^{2}$. \\ Without knowing details on quantum gravity, parameter $\epsilon$ is calculated, which, in general, allows distinguishing the ECOs from BHs. Specifically, a BS (ECO) is undistinguishable from a BH.

Abstract Plant uptake and assimilation of essential nitrogen compounds from the soil are mainly in the form of nitrate and ammonium ions. Plant nitrate transporters (NRTs) play a crucial role in nitrate uptake from the soil into the roots. NRT structural analysis reveals the mechanisms by which these transporters function. Similarly, plant ammonium transporters (AMTs) mediate the uptake of ammonium ions, and their structural analysis has provided valuable information on their mechanisms. After nitrogen uptake by plant roots, the nitrogen metabolism pathway involves the incorporation of nitrogen into organic compounds. Glutamine synthetase (GS) and glutamate synthase (GoGAT) are the master players in this pathway. They work together to convert ammonium ions into glutamine and glutamate, respectively. Different isoforms of GS and GoGAT exist, enabling plants to fine-tune nitrogen metabolism based on environmental cues. Under severe abiotic stress conditions, nitric oxide (NO) has been found to enhance plant survival under drought. Furthermore, the interaction between salinity stress and nitrogen availability in plants has been studied, with NO identified as a potential mediator of responses to salt stress. On the other hand, excessive use of nitrate fertilizers can lead to health and environmental issues. Therefore, alternative strategies, such as establishing nitrogen fixation in plants through diazotrophic microbiota, have been explored to reduce reliance on synthetic fertilizers. Ultimately, genomics can identify new genes related to nitrogen fixation, which could be harnessed to improve plant productivity. By deciphering the genetic basis of nitrogen-fixing traits, researchers aim to develop crops that efficiently utilize nitrogen from the environment.

The burden of hepatocellular carcinoma (HCC) continues to pose a significant global health problem. Several systemic therapies have recently been shown to improve survival for patients with unresectable disease. However, evidence is limited to support the use of neoadjuvant or adjuvant systemic therapies in patients with resectable disease, despite the high risk of recurrence. Neoadjuvant and adjuvant systemic therapies are being investigated for their potential to reduce recurrence after resection and improve overall survival. Our review identified various early-phase clinical trials showing impressive preliminary signals of pathologic complete response in resectable disease and others suggesting neoadjuvant therapies, particularly when combined with adjuvant strategies, may convert unresectable disease to resectable and cause significant tumor necrosis, potentially decreasing recurrence rates. The role of adjuvant therapies alone may also have a role in the management of these patients, particularly in reducing recurrence rates. Heterogeneity in trial design, therapies used, patient selection, and a scarcity of randomized phase III trials necessitate the cautious implementation of these treatment strategies. Future research is required to identify predictive biomarkers, optimize the timing and type of therapeutic combinations, and minimize treatment-related adverse effects, thereby personalizing and enhancing treatment strategies for patients with resectable and borderline resectable HCC.

Fire hazards present a multifaceted global challenge that endangers human lives and environmental safety. Despite advancements in fire risk management technologies and methods, fires continue to be a prime concern for human security. The Arabian Gulf region, influenced by its climatic and environmental conditions, is especially susceptible to these threats. The Emirate of Sharjah, part of the United Arab Emirates, has made significant progress in reinforcing fire safety measures within residential structures, achieving a decrease in the number of fire-related accidents compared to neighboring Emirates. However, the incidence rate remains relatively high. This study undertook a thorough review and assessment of the existing Fire Management System (FMS) for Sharjah's residential sector, leading to the recommendation of a more robust framework. Through a series of literature reviews, interviews with stakeholders, and surveys, using analytical techniques such as the Delphi method and Failure Mode Effect and Criticality Analysis, vital factors that influence the FMS's effectiveness were pinpointed. The study exposed that the current FMS was largely reactive. In response, a proactive framework incorporating nine essential components was designed to strengthen the Sharjah FMS. These components span across various domains such as fire assurance, assessment of fire risks, management of accidents, evaluation of performance, training programs, research and development initiatives, digital services, monitoring of regulatory compliance, firefighting strategies, automated responses to fires, recovery processes, as well as the use of resilient materials and architectural design considerations. Furthermore, the research introduced two specific fire indexes, the HRBFI and the EFRI. Anchored in the principles of Systems Thinking and Industry 4.0, this proposed framework is aimed at streamlining Sharjah's approach to fire management in dwellings, with the objective of diminishing the frequency of fire incidents yearly. The ultimate aspiration of this framework is to enhance the Emirate's standing in terms of safety and to guarantee a living environment that is safeguarded against the risk of fires..

This comprehensive analysis thoroughly examines the topic of adversarial attacks in artificial intelligence (AI), providing a detailed overview of the various methods used to compromise machine learning models. It explores different attack techniques, ranging from the simple Fast Gradient Sign Method (FGSM) to the intricate Carlini and Wagner Attack (C&W), emphasising the wide range of adversarial approaches and their intended goals. The discussion also distinguishes between targeted and non-targeted attacks, highlighting the adaptability and versatility of these malicious efforts. Additionally, the study delves into the realm of black-box attacks, revealing the capability of adversarial strategies to compromise models even with limited knowledge. Real-life examples illustrate the tangible consequences and potential dangers of adversarial attacks in various fields such as self-driving cars, multimedia, and voice assistants. These cases highlight the difficulties in ensuring the legitimacy and dependability of AI-powered technologies and programs. The article stresses the importance of ongoing research and innovation to address the growing difficulties posed by advanced methods like deepfakes and disguised voice commands in preserving the security of AI systems. This study provides valuable insights on how different adversarial strategies and defence mechanisms interact within AI. The results emphasise the urgent need for stronger and more secure AI models to combat the increasing number of adversarial threats in today's AI landscape. These findings can guide future research and innovations in developing more resilient AI technologies that can better withstand various adversarial vulnerabilities and challenges.

Collagen, the most abundant structural protein found in mammals, plays a vital role as a constituent of the extracellular matrix (ECM) that surrounds cells. Collagen fibrils are strengthened through the formation of covalent cross-links, which involve complex enzymatic and non-enzymatic reactions. Lysyl oxidase (LOX) is responsible for catalyzing the oxidative deamination of lysine and hydroxylysine residues, resulting in the production of aldehydes, allysine, and hydroxyallysine. These intermediates undergo spontaneous condensation reactions, leading to the formation of immature cross-links, which are the initial step in the development of mature covalent cross-links. Additionally, non-enzymatic glycation contributes to the formation of abnormal cross-linking in collagen fibrils. During glycation, specific lysine and arginine residues in collagen are modified by reducing sugars, leading to the creation of Advanced Glycation End-products (AGEs). These AGEs have been associated with changes in the mechanical properties of collagen fibers. Interestingly, various studies have reported that plant polyphenols possess amine oxidase-like activity and can act as potent inhibitors of protein glycation. This review article focuses on compiling literature describing polyphenols with amine oxidase-like activity and antiglycation properties. Specifically, we explore the molecular mechanisms by which specific flavonoids impact or protect the normal collagen cross-linking process. Furthermore, we discuss how these dual activities can be harnessed to generate properly cross-linked collagen molecules, thereby promoting the stabilization of highly organized collagen fibrils.

Medium polarity plays a crucial role in charge-transfer processes and electrochemistry. The added supporting electrolyte in electrochemical setups, essential for attaining the needed electrical conductivity, sets challenges for estimating medium polarity. Herein, we resort to Lippert–Mataga–Ooshika (LMO) formalism for estimating the Onsager polarity of electrolyte organic solutions pertinent to electrochemical analysis. An amine derivative of 1,8-naphthalimide proves to be an appropriate photoprobe for LMO analysis. An increase in electrolyte concentration enhances the polarity of the solutions. This effect becomes especially pronounced for low-polarity solvents. Measured refractive indexes provide a means for converting Onsager to Born polarity, which is essential for analyzing medium effects on electrochemical trends. This study demonstrates a robust optical means, encompassing steady-state spectroscopy and refractometry, for characterizing solution properties important for charge-transfer science and electrochemistry.

In the present work, three different atmospheric plasma sprayed (APS) alumina coatings were fabricated using three fused and crushed alumina powders of different particle size fine, medium and coarse. The influence of the particle size on thermal properties and micro-structural features of the produced coating were investigated by thermal insulation test and detailed image analysis technique, respectively. The analyzed micro-structural features include the total porosity, pore size (fine, medium, and large) and cracks. All types of cracks were considered in calculations as voids and were evaluated according to their sizes as pores. All spray parameters except the particle size were fixed throughout the spraying process. The results revealed that the fine starting powder has produced the densest coating with the lowest total porosity and that the total porosity increases with an increasing particle size. This was expected as powders of smaller particle size will reach a higher in-flight temperature and velocity than powders of bigger particle sizes as long as the same spray parameters are applied. However, a detailed image analysis investigation on the three produced coatings showed that the fraction of fine pores and cracks versus the total porosity is substantially higher in coatings produced by using fine starting powders than those produced using medium and coarse powders. In this work, a connection between the thermal insulation and the porosity fraction, which includes fine pores and cracks, was revealed.

In today's context of rising sea levels and subsiding land topography, coastal flooding is a major concern for coastal areas, both nationally, regionally, and internationally. A detailed understanding of these two phenomena is a prerequisite for effective coastal flood management. The main objective of the present study is to contribute to the understanding of the impact of subsidence and sea-level rise on coastal flooding in Saint-Louis, and in particular the Langue de Barbarie, by producing a vulnerability map of submerged surfaces. To this end, the Synthetic Aperture Radar (SAR) interferometry technique is used to process a time series of Sentinel-1 images and estimate land subsidence in the Saint-Louis and Langue de Barbarie area. Interferometric SAR (InSAR) measurements are merged with RCP 2.6 sea-level rise scenarios to identify predicted flooded areas and provide a flood vulnerability map. At the Langue de Barbarie, topographic subsidence is estimated at between -6.4 and -0.4mm/year. In this study, we show that local land subsidence may increase vulnerability to flooding caused by sea-level rise based on 2100 projections. This may represent an increase in the flood zone in the study area. Based on the RCP 2.6 scenario and the subsidence rates obtained, a significant part of the St. Louis coastline and city would be subject to coastal and fluvial flooding for the years 2040 and 2100. For these dates, 29 to and 36 Km2 of the studied area would be occupied by water. Given this situation, research in Saint-Louis needs to focus on adaptation scenarios to coastal risks, to protect coastal communities and safeguard the city's historical heritage.

Brain-stimulation reward, also known as intracranial self-stimulation (ICSS), is a commonly used procedure for studying brain reward function and drug reward. In electrical ICSS, an electrode is surgically implanted into the medial forebrain bundle in the lateral hypothalamus or the ventral tegmental area in the midbrain. Operant lever responding leads to the delivery of electrical pulse stimulation. The alteration in the stimulation frequency-lever response curve is used to evaluate the impact of pharmacological agents on brain reward function. If a test drug induces a leftward or upward shift in the ICSS response curve, it implies a reward-enhancing or abuse-like effect. Conversely, if a drug causes a rightward or downward shift in the functional response curve, it suggests a reward-attenuating or aversive effect. A significant drawback of electrical ICSS is the lack of cellular selectivity in understanding the neural substrates underlying drug reward versus aversion. Excitingly, recent advancements in optical ICSS (oICSS) have facilitated the development of at least three cell type-specific oICSS models – dopamine-, glutamate-, and GABA-dependent oICSS. In these new models, a comparable frequency-rate response curve has been established and employed to study the substrate-specific mechanisms underlying brain reward function and a drug's rewarding versus aversive effects. In this review article, we summarize recent progress in this exciting research area. The findings in these new behavioral models have not only increased our understanding of the neural mechanisms underlying drug reward and addiction but have also introduced a novel experimental approach in preclinical medication development for treating substance use disorders.

Proprioception is an essential part of human movement and body awareness. It is the body's perception of its own spatial understanding, which helps us to accurately move our limbs and maintain balance. Purpose: This study aims to provide a comprehensive overview of the current state of knowledge and analyse bibliometric data about proprioception in gymnastics and acrobatics. Methodology: This article consisted of two phases: 1) a bibliometric review (based Web of Science) and 2) a systematic review (Web of Science, PubMed, and Scopus) of literature. "Gymnast*", "propriocep*", were utilized as search terms to find and choose published data. From a total of 164 studies, 30 were included for data extraction (n participants= 1432 of different age, sports, physical activities, and physical condition. Heterogeneity of studies design and assessment make it difficult to interpret the outcomes and the effect of proprioceptive interventions and comparations between samples. Proprioception is difficult to define in gymnastics considering the evidence references and the physiological considerations. Also, assessment tools used do not necessary evaluate proprioception globally considering the senses involved in gymnastics. Gymnastics training enhances joint awareness and force sense, improving proprioception and reducing injury risk. Proprioceptive exercises should be incorporated into gymnastics programs to enhance stability and precision in movements.

The quickest path problem in the multistate flow networks, also known as the quickest path reliability problem (QPRP), aims at calculating the probability of transmitting a minimum of d units of flow/dat/commodity from a source node to a destination node through one single path within T units of time. Several exact and approximation algorithms have been proposed in the literature to address this problem. Most of the exact algorithms in the literature need prior knowledge of all the network’s minimal paths (MPs), which is considered a weak point. In addition to the time, the budget is always limited in real-world systems, making it an essential consideration in the analysis of systems’ performance. Hence, this study considers the QPRP under the cost constraints and provides an efficient approach based on the node-child matrix to address the problem without knowing the MPs. We show the correctness of the algorithm, compute its complexity results, illustrate it through a benchmark example, and conduct extensive experimental results on the known benchmarks and one thousand randomly generated test problems to demonstrate its practical superiority compared to the existing algorithms in the literature.

The financial inclusion, including all the people with the finance, is very concerned issue all over the world where Bangladesh is also trying to include all the people with the finance. Bangladesh lies in such a group of countries where only 17.6% - 38.6% adults are presently under the reach of the formal financial services. This is because the present banks and other formal financial modes consider the outcome and profitability in a way that, the rural and non-developed areas are always out of the consideration. But these areas consist of the most population of Bangladesh. And only then financial inclusiveness will be successful in Bangladesh when people from these regions will be under formal financial consideration. The paper seeks for a solution to the issue and presents the Unit Banking System as a probable way towards financial inclusion. For implementing the system in Bangladesh, the system needs a slight modification to cope in Bangladeshi economic condition and address the specific needs without hampering the surroundings. Considering all these, the paper shows the status, problems and key points of financial scenario of inclusion in Bangladesh and shows policy for a Modified Unit banking System.

In the coming years, digital applications and services that continue to use the country's native cloud systems will be huge. By 2023, that will exceed 500 million, according to IDC. This corresponds to the sum of all applications developed in the last 40 years. If you are the one you answered, yes! This article is for you!

We review past and present results on the non-local form-factors of the effective action of semiclassical gravity in two and four dimensions computed by means of a covariant expansion of the heat kernel up to the second order in the curvatures. We discuss the importance of these form-factors in the construction of mass-dependent beta functions for the Newton's constant and the other gravitational couplings.

This research introduces a pioneering solution to the challenges posed by gastrointestinal tract (GI) cancer in radiation therapy, focusing on the imperative task of precise organ segmentation for minimizing radiation-induced damage. GI imaging has historically used manual demarcation, which is laborious and uncomfortable for patients. We address this by introducing the ResECA-U-Net deep learning model, a novel combination of the UNet and ResNet34 architectures. Furthermore, we further augment its functionality by incorporating the Efficient Channel Attention (ECA-Net) methodology. By utilizing data from the UW-Madison Carbone Cancer Centre, we carefully investigate several image processing techniques designed to capture critical local characteristics. With its foundation in computer vision concepts, the ResECA-U-Net model is excellent at extracting fine details from GI images. Sophisticated metrics such as intersection over union (IoU) and the dice coefficient are used to evaluate performance. Our study's outcomes demonstrate the effectiveness of the suggested method, yielding an impressive 96.27% Dice coefficient and 91.48% IoU. These results highlight the significant contribution that our strategy has made to the advancement of cancer therapy. Beyond its scientific merits, this work has the potential to significantly enhance cancer patients' quality of life and provide better long-term outcomes. Our work is a significant step towards automating and optimizing the segmentation process, which can potentially change how GI cancer is treated completely.

Buildings consume 30% of the total energy consumption around the globe and 29% of the energy consumption in Egypt which in 2022 had a total population of 102 million, out of which 43 % live in urban areas . The operation of buildings contributes to around 30% of global CO2 emissions due to their high energy consumption (IEA, 2022a). Among the efforts made towards improving the energy efficiency of buildings are Advanced Energy Design Guides (AEDGs), building rating systems, codes, and standards. Furthermore, numerous research studies that are either literature review studies, experimental studies, or computational studies addressed the topic of energy efficiency in buildings. These are all examined in this literature review with the purpose of identifying the research gap in available research with a focus on Egypt. The identified gap is the development of a prescriptive path for the GPRS energy efficiency category based on whole building energy simulations.

Biochar (BC) is a carbonaceous material obtained by pyrolysis at 200−1000 °C in the limited presence of O2 of different vegetable and animal biomass feedstocks. BC has demonstrated great potential, mainly in environmental applications, due to its high sorption ability and persistent free radicals (PFRs) content. These characteristics enable BCs to carry out the direct and PFRs-mediated removal/degradation of environmental organic and inorganic contaminants. The types of PFRs possibly present in BC depend mainly on the pyrolysis temperature and the kind of pristine biomass. Since they also can cause ecological and human damage, a systematic evaluation of the environmental behavior, risks, or management techniques of BC-derived PFRs is urgent. PFRs generally could consist of a mixture of carbon- and oxygen-centered radicals, and of oxygenated carbon-centered radicals, depending on the pyrolytic conditions. Here, to promote a more productive and beneficial use of BC and related PFRs and stimulate further studies to make them environmentally safer and less hazardous to humans, we have first reviewed the most common methods used to produce BC, its main environmental applications, the primary mechanisms by which BC remove xenobiotics, as well as the reported mechanisms for PFRs formation in BCs. Secondly, we have discussed the PFRs environmental migration and transformation; we have reported the main PFRs-mediated applications of BCs to degrade inorganic and organic pollutants, the correlated environmental potential risks, and the possible strategies to limit them.

Weeds can have both positive and negative effects on agricultural environments. However, despite the growing interest in the ecology of weed communities in agricultural areas, few studies have been carried out in the northern region of the Andes of Colombia, where urban and agricultural expansion have gen-erated highly disturbed scenarios. The aim of this study is to analyze the diversity of vegetation and weed seed banks in three agricultural production systems and a forest ecosystem in the northern Andes of Colombia. Hill numbers were used to compare diversity, Beta diversity to assess changes in composition, and range-abundance-dominance curves at different sites. Likewise, indicator species were analyzed to find species associations to each system. The results revealed differences in the composition of weeds between the forest ecosystem and the agricultural production systems, with higher equitability in the forest ecosystem and higher dominance in agricultural systems. A higher differentiation was observed in the dominant species of each agricultural system, highlighting those considered pests due to their life history traits, giving them greater success against various anthropogenic selection pressures. These findings highlight the impact of anthropogenic disturbances on the ecological dynamics of weed com-munities in different ecosystems, which should be considered when planning integrated weed manage-ment techniques.

The aim of this article is to analyze the evidence against the effectiveness of intervention programs based on the participation of parents of children with autism. To obtain the data, a systematic search was carried out in four databases (ProQuest-PsychArticles, ProQuest-ERIC, ProQuest-PubMed, and Scopus). These documents were refined under the inclusion/exclusion criteria and a total of 51 empirical studies were selected. They were classified, first, according to the function of the intervention objective and, later, by the methodology applied (19 studies based on comprehensive interventions, 11 focused on the nuclear symptoms of ASD, 12 focused on the promotion of positive parenting and 9 interactions focused on children play). Once all the documents have been analyzed, the evidence indicates scientific efficacy in most studies, mainly in those based on child development and the application of behavioral analysis principles. Also, the positive influence of parent participation in such programs was demonstrated.

The resistance of Candida spp to fluconazole is a serious problem; Therefore, it must be investigated to expand the understanding of the phenomenon with a view to its clinical applicability. The aim was to evaluate the expression of ERG3, ERG11, CDR1, and SNQ2 genes involving computational analysis. Relative expression was quantified by RT-qPCR. Metrics were obtained by molecular docking and through Fisher's discriminant functions, a predictive classification against susceptibility to fluconazole was performed. The expression of ERG3, CDR1, and SNQ2 genes was higher in resistant strains than in dose-dependent sensitive strains. The gene with the highest expression in strains exposed to fluconazole was CDR1 and, in both resistant and dose-dependent sensitive strains exposed to fluconazole, the ERG11 gene had lower expression. The molecular docking model generated lower median fluconazole-ERG11 contacts than the median fluconazole-ERG3, -CDR1, and -SNQ2 contacts. The predicted classification through the multivariate model for fluconazole sensitivity obtained an accuracy of 73.5%. Resistant strains had a significant expression of CDR1, SNQ2 and ERG3 genes, compared to a comparatively low expression of ERG11. Molecular analysis identified a low affinity between fluconazole and its drug target, which may explain a lower intrinsic susceptibility of the fungus.

There are currently around 78 Nuclear Power Plants (NPP) in the world based on Boiling Water Reactors (BWR). The current parameter to assess BWR instability issues is the linear Decay Ratio (DR). However, it is well known that BWRs are complex non-linear dynamical systems that may even exhibit chaotic dynamics that normally preclude the use of the DR when the BWR is working at a specific operating point during instability. In this work a novel methodology based on an adaptive Shannon Entropy estimator and on Noise Assisted Empirical Mode Decomposition variants is presented. This methodology was developed for real-time implementation of a stability monitor. This methodology was applied to a set of signals stemming from several NPPs reactors (Ringhals-Sweden, Forsmark-Sweden and Laguna Verde-Mexico) under commercial operating conditions, that experienced instabilities events, each one of a different nature

Being overweight or obese is a public health problem. This work evaluated a food and nutrition education (EAN) intervention against overweight schoolchildren in four schools in the West Panama Province. A quasi-experimental before-and-after study that implemented a 34-week EAN intervention through workshops with didactic material to 403 children between 8 and 13 years old. The knowledge and attitude survey was used as an evaluation tool before and after the educational intervention. The prevalence of excess weight (40%) did not report differences after the intervention. No differences were reported in the median level of attitude, although higher levels of knowledge were reported in students of both sexes. EAN in schoolchildren can be effective in acquiring knowledge and maintaining a positive attitude towards food.

The escalating environmental challenges that stem from urban residential waste in densely populated areas have become increasingly prominent in recent times. As a result, the waste management sector has experienced significant growth nationwide. However, due to the predominantly manual nature of these processes, their effectiveness falls short of meeting the current demand. Addressing these issues requires process enhancement. In this context, Industry 4.0, particularly the concept of Digital Twins, emerges as a potential avenue for refining processes. To tackle both current and future industry challenges, it is imperative to create a comprehensive methodology capable of generating effective solutions within the waste management sector. This paper provides an explanation of digital twins, outlines the methodological framework comprising an architectural structure and layered model, and details a series of sequential methodical stages for implementing digital twins based on the specific scope determined by the end-user. A noteworthy aspect is the transformative potential of digital twins in enhancing efficiency and precision within waste management practices. By providing a virtual real-time representation of the waste management system, digital twins empower simulations and experimentation to fine-tune processes. Furthermore, they facilitate informed decision-making by offering a detailed visualization of the complete system, simplifying the identification of challenges and opportunities for improvement. that this article derives from the presentation titled "Digital Twin application methodology for the improvement of production and service systems. Application to waste management processes" at the "Sustainable Smart Cities and Territories International Conference" held in the city of Manizales, Colombia, from 21st to 23rd June 2023.

This paper proposes an approach to estimate the parameters of an AC-DC boost power factor corrector converter which includes an EMI filter. To this end, once the topology is known, measurements at the input and output terminals of the converter are done to identify the values of the passive elements. The proposed methodology is based on the trust-region nonlinear least squares algorithm to identify the parameters of the converter. The steady-state and the transient signals of the converter at the input/output terminals are acquired non-intrusively without any internal modification of the circuitry. The accuracy of the parameter identification carried out is determined by comparing the estimated values with the actual values provided by the manufacturer, and by contrasting the measured signals with the ones obtained with a simulation model with the estimated values of the parameters. The results presented in this paper prove the accuracy of the proposed approach, which can be extended to other power converters and filters.

Research Highlights: The study determined that selective thinning causes different responses, the initial size of the tree released is an influential factor in the growth of species. The temporality of climate and physiological conditions of each species are influential in the growth. It is evident that the defoliation of certain species is an important factor that limits the growth of the species causing thinning to have a negative response. Background and Objectives: The objective is to analyze the behavior of nine timber species, respective to diametric growth after their liberation. This research aims to answer the following questions: (i) How do the selected tree species react to the liberation? (ii) Can the productivity of the trees (diametric growth) be enhanced by liberation? (iii) Are there other factors that influence the diametric growth of the released trees? Materials and Methods: The study was executed in the “Reserva Biológica San Francisco” were 488 trees were monitored, including nine timber species. Therefore, 197 trees were released (removal of competitors) and 251 trees served as reference. To check whether the initial DBH or other factors, like the selective thinning or climate conditions, determine the diameter growth a linear mixed model GLMM was applied. To adjust the linear mixed model a one-way Anova test was executed. Results: Timber species responded differently to the thinning in comparing to reference trees. Therefore, the species analyzed were separated into three groups (positive, negative, and no response to liberation). Conclusions: Liberation potentiates the growth of certain timber species that do not defoliate and considered semi-tolerant to shade. Precipitation and temperature affect all species, but in the defoliate species, it would not be convenient to release them or at least the evidence of these first three years does not show clear differences with control trees. Increase in trees released are higher in trees of the first two diametric classes in all species, this means that larger trees (i.e., older) release does not affect them in a positive way so release should occur in the youngest trees.

This article analyzes the assessment of the four development levels of the Digital Teaching Competence (DTC) to recognize the needs and formulation of challenges in training and educational innovation required in the pedagogical practices of university professors under the current context of the Covid-19 pandemic. The study used an empirical-analytical methodology with a non-experimental, transactional, descriptive design. The sample design was probabilistic, estimated with 95% confidence and 5% error among 252 teachers from various faculties of the University of La Guajira. The selected instrument corresponded to the rubric's application to evaluate the university professor's digital teaching competence in Latin America. Among the study's significant results, we highlight that the rubric presented a high Cronbach's alpha reliability (α: 0.947). In the general assessment of DTC development, it was estimated that 78.2% of teachers are in the first two levels of DTC development assessment (Beginning and Middle). The evaluation rubric allows identifying challenges and opportunities that teacher training must address to advance the professional development of professors.

The organic fraction of municipal solid waste (OFMSW) is a significant environmental threat, and an economic and social challenge to manage. As such, the efficient treatment of OFMSW is a significant key factor in achieving sustainable waste management. Decentralized Composting (DC) develops a new framework of waste management. The DC Analysis Model (DCAM), proposed in our previous study, provides a powerful tool for decision makers, based on the quantification of the DC project characteristics. In this paper, we focus on the qualitative analysis as a complementary tool to support decision making, in cases where quantitative analysis is unequivocal. The qualitative analysis identifies the main players in the field, the critical stakeholders and the potential conflicts between them. It also reveals the root problems and the core competencies for the project's implementation. DCAM qualitative analysis in Shefa-Amr (case study) indicates that unresolved root problems, such as the “lack of national regulation”, “clear ownership of the project” and “lack of ongoing budget” can result in an unsustainable composting system. Countering that, “the commitment of the municipality”, together with “economic viability” and securing “suitable areas for placing composters” are among the most important core competencies for the effective implementation of DC projects.

This study aims to develop a clinical trial to test the efficacy of a Mindfulness Based Stress Re-duction (MBSR) and Self Compassion (SC) Program on self-reported values of anxiety, depres-sion, and stress in parents of children with Autism Spectrum Disorder (ASD) in primary school, in order to assess their integration into the framework of community intervention programs in Spain. Methods: A brief 8-week training program using Mindfulness based intervention (MBSR) and self-compassion (SC) has been applied to ten parents from the Valencian ASD parents’. Partici-pants were assigned to two groups, both groups received the same treatment but at two different measurement moments. Depression, Anxiety, Stress, Satisfaction with Life and Mindful Atten-tion Awareness measurements were assessed, in all participants, in three testing moments. Results: Analysis of Variance results suggested that MBSR and SC training reduces stress and anxiety and increases Mindful Attention Awareness. No significant changes were found in Life Satisfaction measurements. Conclusions: The small number of participants prevents us from generalising the results found. More MBSR and SC clinical trials are needed in parents of ASD with results on anxiety, depression and stress in order to demonstrate the relevance of the inclusion of these programmes in community-based early intervention services.

Objectives: The aim of our current study was to analyze whether the use of important measures of methodological quality and reporting of randomized clinical trials published in the field of cardiovascular disease research have changed over time. Further aim was to investigate whether there was an improvement over time in the ability of these trials to provide a good estimate of the true intervention effect. Methods We conducted two searches in the Cochrane Central Register of Controlled Trials (CENTAL) database to identify cardiovascular clinical research trials published in either 2012 or 2017. Randomized clinical trials (RCTs) trials in cardiovascular disease research with adult participants were eligible to be included. We randomly selected 250 RCTs for both publication year 2012 and 2017. Trial characteristics, data on measures of methodological quality and reporting were extracted and risk of bias for each trial was assessed. Results As compared to 2012 in 2017 there were significant improvements in the reporting of the presence of a data monitoring committee (42.0% in 2017 compared to 34.4% in 2012), and a positive tendency of registering cardiovascular disease research RCTs in clinical trial registries (83.6% in 2017 compared to 72.0% in 2012). On the other hand, we also observed that significantly fewer RCTs reported sample size calculation (60.4% in 2017 compared to 98.4% in 2012) in 2017 as compared to 2012. RCTs in 2017 were more likely to have low overall risk of bias ( RoB ) than in 2012 (29.2% in 2017compared to 21.2% in 2012). Conclusion: As compared to 2012 in 2017 there were significant improvement in some, but not all the important measures of methodological quality. Although more trials in the field of cardiovascular disease research had a lower overall RoB in 2017, the improvement over time was not consistently perceived in all RoB domains.

In 2023, the technological landscape witnessed an unprecedented surge of transformative innovations, including Web 3.0 and machine learning, poised to revolutionize various aspects of our daily lives. At the forefront of this revolution stands artificial intelligence (AI), which has evolved from a concept once confined to science fiction into an indispensable force reshaping industries on a global scale. Notably, recent years have seen remarkable strides in AI functionalities, particularly in machine learning, computer vision, and natural language processing. These advancements have empowered AI to generate diverse interactions and media autonomously. This study ultimately provides invaluable insights into the dynamic intersection of AI and Advertising, con-tributing to a deeper comprehension of this evolving field. This study conducts a comprehensive review of Artificial Intelligence within the advertising domain, employing network analysis. By meticulously examining the evolution of AI through co-occurrences of terms, keywords, and co-authorship analysis, we aim to unveil the relationship of AI & Advertising through the lens of Generative models to identify pivotal trends, core concepts, and seminal studies that have profoundly influenced the industry. The analysis charts the trajectory leading to the emergence of Generative Artificial Intelligence (GenAI), a transformative development poised to revolutionize advertising practices and consumer engagement. In tandem with these objectives, the results highlight vital trends, emphasizing the growing prominence machine learning tools and techniques such as deep learning techniques and advanced natural language processing methods like word2vec, GANs, and more in shaping the future of advertising practices.

This paper shows the proposal of the use of linked data for smart metering systems. The aim of linked data in smart grid applications such as smart metering systems is to give semantic knowledge of the energy transactions between all participators in the power markets. In combination with other technologies like blockchain, the linked data could improve decentralization and security in the world's energetic future.

Metabolic pathways provide key information to achieve a better understanding of life and all its processes; this is useful information for the improvement of medicine, agronomy, pharmacy, and other similar areas. The main analysis tool used to study these pathways is based on the idea of pathway comparison, using graph data structures. Metabolic pathway comparison has been defined as a computationally complex task \cite{ay2011submap,abaka2013campways}. In previous work from 2017, two different approaches that simplify the problem of comparing pathways represented as graphs were introduced. The first algorithm consists of the transformation of a two-dimensional graph structure, representing a metabolic pathway, to a one-dimensional structure and thus aligning the corresponding data using a reduced 1 dimension string. The second algorithm consists of performing a paired analysis between reactions in pathways and thus eliminating all similarities, finally, showing these differences to the user. The suggestion is to use the information provided by these algorithms as a previous analysis to a deeper, more expensive, comparison tool use. Here we provide an extension of this work with more data and deeper analysis. These methods have shown to be an effective way to treat the problem of metabolic pathway comparison as listed in the discussion and results section. Our results show evidence of a quick, simple and effective way to resolve the described problem.

The construction industry is responsible for 40 to 45% of primary energy consumption in Europe alone. Therefore, it is essential to find new materials with a lower environmental impact in order to attain sustainable housing. This study aims to determine and compare the environmental impact of two clay samples forming a basis for the manufacture of traditional brick, a standard material in building construction; traditional red clay brick and a brick based on clay mixed with a biological ingredient. The samples of fired clay were manufactured at the laboratory scale, the results being valid exclusively as indicators for the extrapolation of the analysis to other studies. The results of the environmental impact of these formulations have been examined through an evaluation of life-cycle analysis (LCA), observing that the incorporation of biological pore forming agents led to a decrease of around 15 to 20% of all impact categories studied. Thus, the suitability of using biological-based additives in clay bricks was confirmed both for their constructive characteristics (lighter material) and increased energy efficiency (better thermal insulation) considering the environmental point of view.

Interferon-beta is one of the most widely prescribed disease-modifying therapies for multiple sclerosis patients. However, this treatment is only partially effective, and a significant proportion of patients do not respond to this drug. This paper proposes an alternative fuzzy logic system based on the opinion of a neurology expert to classify relapsing-remitting multiple sclerosis patients: high, medium, and low responder to interferon-beta. Also, a pipeline prediction model trained with biomarkers associated to interferon-beta response is proposed for predicting whether patients are potential candidates to be treated with this drug, in order to avoid ineffective therapies. The classification results shows that the fuzzy system presents a 100% efficiency compared with an unsupervised hierarchical clustering method (52%). So, the performance of the prediction model is evaluated, and a 0.8 testing accuracy is achieved. Hence, a pipeline model including data standardization, data compression, and a learning algorithm, can be a useful tool for getting reliable predictions about the response to interferon-beta.

This article addresses the complex challenge of simultaneously enhancing contrast and detail in an image, where improving one property often compromises the other. This trade-off is tackled using a multi-objective optimization approach. Specifically, the proposal's model integrates the sigmoid transformation function and unsharp masking highboost filtering with the NSGA-II algorithm. Additionally, a posterior preference articulation is introduced to select three key solutions from the Pareto front: the maximum contrast solution, the maximum detail solution, and the knee point solution. The proposed technique is evaluated on a range of image types, including medical and natural scenes. The final solutions demonstrated significant superiority in terms of contrast and detail compared to the original images. The three selected solutions, although all are optimal, captured distinct characteristics within the images, offering different solutions according to field preferences. This highlights the method's effectiveness across different types and enhancement requirements and emphasizes the importance of the proposed preferences in different contexts.

This paper presents a new method for the design of separable denominators 2-D IIR filters with nearly linear phase in the passband. The design method is based on a balanced-realization model reduction technique. The nearly linear-phase 2-D IIR filter is designed using 2-D model reduction from a linear-phase 2-D FIR filter, which serves as the initial filter. The structured controllability and observability Gramians $P^s$ and $Q^s$ serve as the foundation for this technique. These Gramians are block diagonal positive-definite matrices that satisfy 2-D Lyapunov equations. An efficient method is used to compute these Gramians by minimizing the traces of $P^s$ and $Q^s$ under linear matrix inequalities (LMI) constraints. The use of these Gramians ensures that the resulting 2-D IIR filter preserves stability and can be implemented using a separable denominator 2-D filter with fewer coefficients than the original 2-D FIR filter. Numerical examples show that the proposed method compares favorably with existing techniques.

All over the world, externally bonded fiber-reinforced polymer systems used to strengthen concrete elements improve building sustainability. However, reports issued by the American Concrete Institute Committee 440 called for heavy scrutinizing before actual field implementation. The very limited number of proposed equations lacks reliability and accuracy. Thus, further investigation in this area is needed. In addition, machine learning techniques are being implemented successfully in developing strength models for complex problems. This study aims to provide a reliable machine learning model based on an experimental database. The proposed model was developed and validated against the experimental database and the very limited models in the literature. The model showed improved agreement with the experimental results compared to the previous models.

Quantum revival phenomena, wherein the wave function of a quantum system periodically returns to its initial state after evolving in time, are investigated in this study. Focusing on electrons confined within a quantum box with an impurity, both weak and strong coupling regimes are explored, revealing intricate relationships between impurity parameters and temporal dynamics. The investigation considers the influence of impurity position, impurity strength, and external factors such as aluminum concentration, temperature, and hydrostatic pressure on classical periods and revival times. Through analytical derivations and graphical analyses, the study elucidates the sensitivity of quantum revivals to these parameters, providing valuable insights into the fundamental aspects of quantum mechanics. While no specific physical applications are discussed, the findings offer implications for quantum heat engines and other quantum-based technologies, emphasizing the importance of understanding quantum revivals in confined quantum systems.

Purpose: this paper evaluates the effect of thermo-formed aligners with complementary biomechanical attachments (CBA) on periodontal ligaments (PDL) during the expansion process of the maxillary arch using simulations based on the finite element method (FEM). Methods: four types of teeth (canine 3, premolar 4, premolar 5 and molar 6) were modeled using 3D CAD. In addition, aligners, CBAs and PDL were also 3D modeled. With this information, a FEM model was generated, and a clinical rehabilitation scenario was simulated. For the validation of the results, a comparison with medical records was performed. Results: for canine 3, the displacement was 0.134 mm with a maximum stress of 4.822 x10-3MPa in the amelocemental junction. For premolar 4, the displacement was 0.132 mm at a maximum stress of 3.273x10-3MPa in the amelocemental junction. Premolar 5 had a displacement of 0.129 mm and a stress of 1.358 x10-3MPa at 1 mm from the amelocemental junction. Molar 6 had a displacement of 0.124 mm and a maximum stress of 2.440 x10-3MPa. Conclusions: The simulations showed that the use of CBA reduces tooth tipping. The model with Vestibular CBA presented the best results in terms of the dental movement of expansion of the maxillary arch with the use of thermoformed aligners. Significance: Considering the difficulty of performing in vivo tests that evaluate the configuration effectiveness of the different CBA alternatives in thermoformed aligners, FEM techniques were used to reduce time and costs, and get accurate results with minimal errors.

The Hollow fiber membrane contactor (HFMC) is an intensification process that combines membrane and absorption technologies, being a technology in expansion, so the dynamics of this process is crucial for an increase in industrial scale-up. In this manuscript a rigorous dynamic model of an HFMC is developed and simulated in Python software for the absorption of post-combustion CO2 using a monoethanolamine (MEA) solution, which was validated using available data in literature in steady state. Dynamic simulations were performed to analyze the model's capability to predict the effect of disturbances on the responses of CO2 capture ratio and loading. Four distinct experiments were conducted by step changes and pulse disturbances at the following variables: gas and liquid volumetric flow rates, CO2 composition in flue gases, and CO2 lean load. The gas phase showed a faster response compared to the liquid. The CO2 capture ratio and rich loading presented opposite responses when disturbing both liquid flows, and for the composition and lean loading variations, the capture ratio presented an inverse response characteristic, while the loading showed a delayed response. As the model proved to be capable of returning to the reference state, it can potentially be used for control studies purposes.

The COVID-19 pandemic brought about a significant change in mobility habits within cities, with a significant decrease in the use of collective urban transport that has only been partially and unevenly reversed. To recover the previous rates of use, many cities are analyzing which characteristics of the urban transport network are hindering this recovery process in order to design actions to promote sustainable mobility. This article shows a study carried out in the city of Almería (Spain), where the operation variables of the municipal bus network have been analyzed (frequency, average vehicle occupancy, length of the lines, urban or suburban character, circularity, nodality or intermodality) to detect what aspects are more determinant on the number of users recovered. The results show that the lines that have recovered the most users in average are suburban lines, as well as the nodal lines that serve key centroids such as the university. Thus, the dependence of users on public transport would be the most important determinant in recovery, more than other variables representative of the service´s intrinsic quality. This result shows that, without compromising the necessary quality of the service, the restrictions on less sustainable transportation alternatives will be those that, to a greater extent, allow for the prompt recovery of the space lost by urban public transportation.

(1) Background: In Eugenia Stipitata Mac Vaugh (Arazá), there is an abundance of flavonoids, carotenoids, and phenolic acids, which are bioactive compounds with antioxidant, anticarcinogenic, antimicrobial, anti-inflammatory, antispasmodic, antiulcer, and cardiovascular disease prevention benefits. Therefore, the aim of this review is to compile the compounds that have been identified in the fruit and gather information about secondary metabolites to establish their potential preventive and therapeutic effects; (2) Methods: a literature search was conducted in repositories and databases such as Science Direct, Scopus, PubMed, Web of Science, Agriculture Collection Gale, SAGE, OXFORD University, DOAJ, among others. Articles identifying and quantifying bioactive compounds present in Arazá were included; (3) Results: Five studies meeting the inclusion criteria were incorporated, resulting in the compilation of 82 compounds, of which 24 were identified and quantified, while 58 were solely identified. This review was able to identify and report the concentration, and in some cases, the quantity, of phenolic compounds with antioxidant and anti-inflammatory capabilities present in Arazá; (4) Conclusions: With this scope, it was possible to obtain a more comprehensive understanding of the fruit's potential to potentially enhance health aspects, thereby providing greater prominence and added value to this product, allowing for more frequent inclusion in the diets of consumers, and even enabling exportation.

Paving blocks are concrete pieces placed in exposed places to the weather, which are sub-jected to loads and wear. Hence, quality control in the manufacture of paving blocks is es-sential to guarantee the properties and durability of the product in construction projects. In Ecuador, the requirements are described in the Ecuadorian technical standard "NTE INEN 3040", and tensile splitting strength is a fundamental requirement to guarantee product quality. It is analyzed using quality control measurements such as dimensions, the weight of the fresh paving block in the vibro-compacted process, and the percentage of water absorption in order to know how the variables influence and manage to predict the tensile splitting strength to avoid product non-conformity in advance, having a timely and better control of the manufacturing process. The data was obtained from a company that can produce 30 000 units per day of rectangular paving blocks with 6 cm thickness. Mul-tivariate models such as multiple linear regression, regression trees, random forests and neural networks are performed to predict the tensile splitting strength variable through two groups of predictors; the first group is the thickness mm, width mm, length mm, mass of fresh paving block g and percentage of water absorption %. The second group of pre-dictor variables is the density of the fresh paving block kg/m3 and the percentage of water absorption %. It is concluded that the multiple linear regression method performs better in predicting the first group of predictor variables with a mean square error (MSE) of 0.110086, followed by the neural network without hidden layers resulting in an MSE of 0.112198. The best method for the second set of predictors was the neural network with-out hidden layers with a mean square error ( MSE ) of 0.112402, closely followed by the multiple linear regression model with an MSE of 0.115044.

Endurance triathlons impose substantial physiological stress, yet effects of short-course formats remain relatively unexplored. In this preliminary study, we assessed proteinuria and hydration levels in 27 well-trained triathletes (41.9 [7.4] years) who completed a sprint triathlon consisting of a 1500-m swim, 26-km cycle, and 8-km run. Urine samples were collected before and after the race. The results showed an increase in cases of post-race proteinuria from four to nine (p=0.03). Also, one case of urobilinuria and ketoacidosis was observed after the race. Pre-race glucosuria, which was present in nine cases, decreased to three cases post-race. Although hematuria cases decreased from six to two (p=0.13), pre-race leukocyturia (found in two cases) resolved post-race. There was a significant increase in urine specific gravity (from 1.018 to 1.023, p=0.03), indicating dehydration. In conclusion, short-course triathlons were found to induce post-race proteinuria, urobilinuria, and dehydration without exacerbating pre-race glucosuria, hematuria, or leukocyturia. These preliminary findings contribute to our understanding of medical guidelines for sprint triathlons, an area of endurance sports that has received limited research attention. Further investigation, both mechanistic and longitudinal, is warranted in this regard.

The study reports the effect of some metal carbides (niobium carbide, vanadium carbide, titanium carbide, and manganese sulfide) on hydrogen embrittlement in the pipeline industry using plane wave’s density functional theory (DFT). Our results predicted that the interaction of hydrogen molecules with these metals carbide occurs in the long range with binding energy varying in the energy window [0.70eV to 0.043eV]. Also, our study shows the desorption of H2 molecules from these metal carbides in the chemisorptions. Since, hydrogen embrittlement, occurs in the atomic state of hydrogen, therefore our finding in the atomic interaction of hydrogen with NbC, VC, TiC, and MnS showed that the strength of the trapping of the hydrogen atom could be classified as: TiC+H>VC+H>NbC+H> MnS+H. In addition, our study reveals that the carbon site is the most favorable hydrogen trapping site than the metal one. Furthermore, our results demonstrate that increasing the layer can also be an efficient way to enhance the trapping capacity.

Deep neural networks with powerful auto-optimization tools have been widely applied in various research fields, e.g., NLP and computer vision. However, existing neural network architectures typically are constructed using different inductive biases, e.g., preconceptions, expecting to decrease parameter search space during training, reduce computational cost or introduce expert knowledge in the neural network design. As an alternative, Multilayer Perceptron (MLP) provides much better freedom for exploration, has a lower inductive bias than convolutional neural networks (CNNs), and offers good flexibility in learning complex patterns. Even though, such neural architectures are commonly built in a flat Euclidean space, which is not necessarily the optimal space for any data, and is especially not good for modeling hierarchical correlations. Hyperbolic neural networks (HNNs) have gained attention for their ability to capture hierarchical structures present in complex data types like graphs. Recently, there has been an increasing interest to extend HNNs to computer vision tasks, motivated by the observations that images possess rich hierarchical relations. However, this is generally applied by employing a Euclidean backbone for learning higher-level semantic representations and only incorporating a hyperbolic classifier for classification, which, we argue, does not make full use of the advantage of hyperbolic space. Considering the recovery of the attention-free Multilayer Perceptron(MLP), in this paper, we extend it to non-Euclidean space and propose a novel architecture, named Hyperbolic Res-MLP (HR-MLP), that leverages fully hyperbolic layers to learn feature embeddings and perform image classification in an end-to-end fashion. With the help of the proposed Lorentz cross-patch and cross-channel layers, we can directly perform operations in the hyperbolic domain with fewer parameters, making it faster to train and providing comparatively better performance than its Euclidean counterpart. Experiments on CIFAR10, CIFAR100, and MiniImageNet demonstrate a comparable and superior performance when compared to Euclidean baselines. Our code is available at (https://github.com/Ahmad-Omar-Ahsan/HR-MLP)

The purpose of this paper is to develop an index system for measuring the compliance of high-rise residential buildings with fire requirements and also to develop an index system for measuring the fire response efficiency, which is linked to the index of compliance with fire requirements. The higher the compliance rate, the greater the chance of a successful response. The two systems de-pend on the automation of the firefighting system management processes using the techniques of the fourth industrial revolution and developed based on the consultation of subject matter experts in the field. The main elements of the indexes were identified, which were based mainly on several variables, including the fire administrative system, the firefighting system, the residents, the loca-tion of the high-rise residential buildings from the fire extinguishing station, and the height of the high-rise residential building. The two systems can contribute to improving emergency prepared-ness in high-rise residential buildings in the Emirate of Sharjah and are also considered as a measurement index for compliance with fire requirements in the Emirate of Sharjah.

On the basis of a limited number of reasonable axioms, we discuss the classification of all the possible universality classes of diffeomorphisms invariant metric theories of quantum gravity. We use the language of the renormalization group and adopt several ideas which originate in the context of statistical mechanics and quantum field theory. Our discussion leads to several ideas that could affect the status of the asymptotic safety conjecture of quantum gravity and give universal arguments towards its proof.

Exploring the biological significance of mutations in SARS-CoV-2 coronavirus, causing the COVID–19 pandemic, has recently become an area of paramount interest for many researchers, who are pouring their tremendous efforts, in cracking the COVID–19 pandemic code. One of many such mutations that have occurred in the viral genome is V483A mutation, which is a part of the receptor-binding motif (RBM), present in the S1 domain of the spike protein. V483A mutant virus is becoming popular in North America with 36 cases so far, due to its frequent occurrences in recent days. In this review, we have assembled all information, currently available on V483A mutation, and have made a critical analysis based on the perspectives of many researchers all around the world. Comparison is made between the wild type and the V483A mutants to analyze certain factors like the type of interaction between the virus and host cell interface, binding affinity, stability, partition energy, hydrophobicity, occurrence rate, and transmissibility. Insilico dynamic analysis shows minimal alteration in the receptor-binding domain (RBD) of V483A mutant protein in free-state and no significant change of mutant tertiary structure of RBM upon binding to the ACE2 receptor. Comprehensive details about infectivity and evasion of the immune system by the virus are discussed. This information can in turn be of monumental importance in the field of vaccine and drug development because the mutants are becoming resistant to the vaccines and monoclonal antibodies.

Maize is the staple cereal in Malawi, with a daily per capita consumption of 383g (dry matter basis), primarily consumed as dehulled maize flour used to cook nsima, a thick porridge. However, the extent of mass and nutrient loss during dehulling remains unclear in this food-insecure country, where the household maize harvest typically lasts only 6–7 months. In the current study, a milling experiment to determine yield and micronutrient losses was conducted. Milling batches (30 kg) of four maize grain varieties were dehulled at three abrasive disk dehullers under controlled conditions. Mass losses ranged from 18.8% to 42.7%, with a mean of 28.2±5.7%. Maize variety and dehuller significantly affected mass loss (p&lt;0.05). Initial protein, iron, and zinc concentrations were 8.8 ±1.0 g/100g, 20.5±2.0 µg/g, and 18.2 ±2.6 µg/g, respectively. Post-dehulling nutrient true retention varied for protein (49.7% to 75.6%, mean=64.7±7.0%), iron (18.7% to 71.6%, mean=37.6±12.0 %), and zinc (11.0% to 46.2%, mean=27.9±8.7 %). Maize variety significantly influenced mass and protein loss (p &lt; 0.05), while dehuller influenced mass, iron, and zinc losses. However, no significant difference (p &gt; 0.05) was found in the interaction between dehullers and variety on mass and nutrient losses, respectively. Given Malawi's precarious food insecurity situation, transitioning from dehulled maize flour nsima to whole maize flour or less refined nsima, is imperative. Our study findings can have food and nutritional savings for other southern Africa countries where the dehulling practice is rampant.

Epithelial ovarian cancer (EOC) remains the most lethal gynecologic malignancy, largely due to metastasis and drug resistant recurrences. Fifteen percent of ovarian tumors carry mutations in BRCA1 or BRCA2, rendering them vulnerable to treatment with PARP inhibitors such as olaparib. Recent studies have shown that TGFβ can induce “BRCAness” in BRCA wild-type cancer cells. Given that TGFβ is a known driver of epithelial to mesenchymal transition (EMT), and the con-nection between EMT and metastatic spread in EOC and other cancers, we asked if TGFβ and EMT alter susceptibility of EOC to PARP inhibition. Epithelial EOC cells were transiently treated with soluble TGFβ and their clonogenic potential, expression and function of EMT and DNA repair genes, and response to PARP inhibitors compared with untreated controls. A second epithelial cell line was compared to its mesenchymal derivative for EMT and DNA repair gene expression and drug responses. We found that TGFβ and EMT resulted in downregulation of genes responsible for homologous recombination (HR) and sensitized cells to olaparib. HR efficiency was reduced in a dose-dependent manner. Furthermore, mesenchymal cells displayed sensitivity to olaparib, cis-platin, and the DNA-PK inhibitor Nu-7441. Therefore, treatment of disseminated, mesenchymal tumors may represent an opportunity to expand clinical utility of PARP inhibitors and similar agents.

Objectives: Social distancing measures are currently implemented to control COVID-19 pandemic in many countries, including Saudi Arabia. The aim of this study was therefore to evaluate the awareness and adherence of the Saudi population to these measures. Methods: A web-based questionnaire was designed with 16 questions (8 questions related to demographics, 3 in relation to awareness about social distancing and 5 related to overall practice of social distancing). Results: 5105 participants completed the survey [58.4% female, 66.3% young individuals (aged 18-37 years), 55.8% bachelor degree holders, and 51.0% from the western region]. The Saudi Ministry of Health (MOH) was the main source of information about COVID-19 for most participants (78.2%). High awareness (81.3%) regarding social distancing was observed, associated mainly with female participants, those from the middle region and those with high education and income. Overall implementation of social distancing was satisfactory (score 3.13/5), with 37.8% never leaving home during the home-stay period. Better adherence to social distancing was observed for female participants, higher degree holders and those aged over 38 years. Conclusions: Organised plans by the Saudi MOH have been effective in raising awareness and improving practice of social distancing among public. However, the observed lower practice of social distancing by individuals with lower education and income indicates the need for targeted interventions to achieve better outcome.

The proliferation of radio frequency devices in today's society, especially in smart homes, Internet of Things devices, and smartphones, underscores the urgent need for robust identification methods to strengthen cybersecurity. This paper delves into the field of radio frequency fingerprinting to propose a Bluetooth device identification method based on the application of the Jensen-Shannon divergence to the statistical distribution of noise in Bluetooth signals. A detailed case study is performed to investigate the Bluetooth radio frequency noise recorded at 5 Gsps from different devices is investigated to define a statistical radio frequency fingerprint for each Bluetooth device. A noise model is used to extract a unique, universal, persistent, recoverable, and robust statistical radio frequency fingerprint that identifies each Bluetooth device. Then, using the Jensen-Shannon divergence, different noise signals provided by each Bluetooth device are compared with the statistical radio frequency fingerprint of all devices and a membership resolution is declared. The study shows that the proposed method can discriminate between devices of the same brand and model, achieving an identification effectiveness of 99.5 \%. By leveraging the statistical radio frequency fingerprint of Bluetooth devices, this research not only contributes to the advancement of the field of implicit device authentication systems based on wireless communication but also provides valuable insights into the practical implementation of radio frequency identification techniques that could be useful in forensic processes.

This article is a theoretical contribution to mental model research, which currently has different threads. Whereas some researchers focus on the perceived causal structure, others also include decision policies and decisions. We focus on the link between recognized causal structure (“mental models of dynamic systems”) and policies, proposing Johnson-Laird’s theory of mental models as the link. The resulting framework hypothesizes two types of systematic mental model errors: (1) misrepresentation of the system’s structure and (2) failure to deploy relevant mental models of possibilities. Examination of three experiments through this lens reveals errors of both types. Therefore, we propose that the cognitive theory of mental models opens a path to better understand how people construct their decision policies and develop interventions to reduce such mental model errors. The article closes by raising several questions for empirical studies of the reasoning process leading from mental models of dynamic systems to decision policies.

The presence of premature termination codons (PTCs) in transcripts is dangerous for the cell as they encode potentially deleterious truncated proteins that can act with dominant-negative or gain-of-function effects. To avoid synthesis of these shortened polypeptides, several RNA surveillance systems can be activated to decrease the level of PTC-containing mRNAs. Nonsense-mediated mRNA decay (NMD) ensures an accelerated degradation of mRNAs harboring PTCs by using several key NMD factors such as up-frameshift (UPF) proteins. Another pathway called nonsense-associated altered splicing (NAS) upregulates transcripts that have skipped disturbing PTCs by alternative splicing. Therefore, these RNA quality control processes eliminate abnormal PTC-containing mRNAs from the cells by using positive and negative responses. In this review, we will describe the general mechanisms of NMD and NAS and their respective involvement in the decay of aberrant immunoglobulin and TCR transcripts in lymphoid cells.

Our research assesses the effects of four forest species, namely Swietenia macrophylla King, Swietenia mahogany (L.) Jack., Pinus occidentalis Swartz, and Pinus caribaea Morelet var. Caribaea, on organic carbon (OC) dynamics and carbon dioxide equivalent balance (BCO2 Eq.) in the soils beneath these species. Reforestation projects in the study region cover 1,200, 543, 770, and 1,152 hectares, with these four species, respectively, being the most relevant species in reforestation projects within the country. To determine the BCO2 Eq. per unit area, we compared the greenhouse gas (GHG) fluxes of carbon dioxide (CO2), methane (CH4), and nitrous oxide (N2O) with the OC reserves found in the mineral soil to a depth of 30 cm and in the forest litter. For 18 months, we conducted field measurements in sixteen stands, four for each species. Our results indicate that S. macrophylla absorbed the highest amount of CO2, while S. mahogany released the highest amount into the atmosphere. BCO2 Eq. from S. macrophylla soils was -23.19 metric tons of CO2 Eq. ha-1 year-1, while for P. occidentalis, S. mahogany, and P. caribaea, the corresponding quantities were -3.838, -2.299, and +0.982, respectively. During the measurement period, soils under S. macrophylla, P. occidentalis, and P. caribaea were net sinks of CO2 Eq., while soils under S. mahogany behaved as a source. The absorption rate of CO2 Eq. from the atmosphere was approximately 6, 10, and 24 times higher in S. macrophylla when compared to the respective rates of P. occidentalis, P. caribaea, and S. mahagony.

Many bacteria have the ability to survive in challenging environments; however, they cannot grow on standard culture media, a phenomenon known as the Viable but Non-Culturable (VBNC) state. Bacteria commonly go into the VBNC state under nutrient-poor environments or under stressful conditions. This review explores the concept of the VBNC state, providing insights into the beneficial bacteria known to employ this strategy. The investigation covers different chemical and physical factors that can induce the latency state, cell features, and gene expression observed in cells in the VBNC state. The revision also covered the significance and applications of beneficial bacteria, methods for evaluating bacterial viability, the ability of bacteria to persist in environments associated with higher organisms, and the factors that facilitate the return to the culturable state. Knowledge about beneficial bacteria capable of entering the VBNC state remains limited, however, beneficial bacteria in this state could face adverse environmental conditions, and return to culturable state when conditions become suitable and continue to exert their beneficial effects. Likewise, this unique feature positions them as potential candidates for healthcare applications, such as the use of probiotic bacteria to enhance human health, applications in industrial microbiology for the production of prebiotics, functional foods, and in the beer and wine industry. Moreover, their use in formulations to increase crop yield and for bacterial bioremediation offers an alternative pathway to harness their beneficial attributes.

In this work, we report the caloric effect for an electronic system of the antidot type, modeled by combining a repulsive and attractive potential (parabolic confinement). In this system, we consider the action of a perpendicular external magnetic field and the possibility of having an Aharonov-Bohm flux (AB-flux) generated by a current passing through a solenoid placed inside the forbidden zone for the electron. The energy levels are obtained analytically, and the model is known as the Bogachek and Landman model. We propose to control the caloric response of the system by varying only the AB-flux, finding that in the absence of an external magnetic field, the maximization of the effect always occurs at the same AB-flux intensity independent of the temperature while fixing the external magnetic field at a non-zero value breaks this symmetry and changes the point where the caloric phenomenon is maximized and is different depending on the temperature to which the process is carried. Due to the great diversity in technological applications that have antidots in electronics, the possibility of controlling their thermal response just by varying the intensity of the internal current inside the solenoid can be a platform of interest for experimental studies.

(1) Background: Executive functioning is a concept that suggests a scheme of relationship between brain-mind and behavior, through a plan and control of individuals actions on tasks and context. This work is an approach to the study between relationship of abilities (flair) and the execution, between cognitive development and executive functioning as intelligence and creativity and reading writing learning association. The objective is trying to give a definition of neuropsychological profile of Gifted Students; (2) Methods: We studied 20 Gifted Student assessments by a school counselor, under some characteristics as having greater than 125 IQ. The age range was 6:8 to 11:8 from Primary School. Instruments were WISC-V. BRIEF-2 and TTCT; (3) Results: We observed a positive correlation between IQ and Inhibition, that would keep relation with behavioral mechanism (guide work, autonomy, impulse control, ...) of students to develop cognitive and metacognitive abilities as going in-depth in habits, skill, and strategies of intellectual work in the classroom; (4) Conclusions: There is a distance between executive functioning and IQ. Correlations, considering our sample, would express a halfway association between both variables. Association that would be explained for the connection or underlying cognitive mechanism in some factors of variables.

: This study aims at exploring Turkish consumers’ behaviors toward purchasing green fashion. A mixed-methods approach was used in this study. Six experts from the main brands in the fashion industry in Türkiye were interviewed. A total of 268 questionnaires were collected from Turkish consumers, and their responses were analyzed. The theory of planned behavior (TPB) informed the theoretical framework of this study. The main components of the TPB were extended to include perceived consumer effectiveness. A thematic analysis was conducted to analyze and code the interviews. To test the hypotheses, structural equation modeling (SEM) was conducted. The findings show that the key factors of the TPB, i.e., attitudes (ATTs), subjective norms (SNs), and perceived behavioral control (PBC), as well as perceived consumer effectiveness, significantly impact the intentions of Turkish consumers to purchase sustainable fashion. However, the results highlight some inconsistencies, gaps, and barriers that discourage the purchase intentions of consumers, including a lack of information, misinformation, greenwashing, green skepticism, a lack of trust, and the high cost of sustainable fashion.