In the field of clinical medicine, the real-time monitoring of carbon dioxide gas exhaled by the human body is of great significance. At present, the detection devices in the market are mainly detected by sucking a small amount of gas in the nasal cavity to the detection device, and there are some problems such as too long sampling tubes, easy blockage or distortion, and abnormal gas dispersion. In this paper, a micro-nano optical fiber sensor that can directly detect the concentration of end-tidal carbon dioxide is proposed. The measurement is achieved by using the principle of high evanescent field absorption, and the operating band is 2.004 μm. The sensor uses micro-nano optical fiber as the sensing area, and then detects the presence of carbon dioxide gas exhaled by human body through optical power attenuation. The function of micro-nano fiber is to realize the transmission of signal light and also serve as the absorption medium of the gas to be measured. In addition, the variation of light power also reflects the respiratory cycle of the human body. The sensor can realize rapid real-time response to carbon dioxide gas detection, with small size, low cost, and easy to replace. It has great application potential in clinical scenarios such as Gastrointestinal Endoscopes that require real-time monitoring of human respiration.

Flexible electrochemical sensors can adhere to any bendable surface with conformal contact, enabling continuous data monitoring without compromising the surface's dynamics. Among various materials that have been explored for flexible electronics, metal-organic frameworks (MOFs) exhibit dynamic responses to physical and chemical signals, offering new opportunities for flexible electrochemical sensing technologies. This review aims to explore the role of electrocatalysis in MOF films specifically designed for flexible electrochemical sensing applications, with a focus on their design, fabrication techniques, and applications. We systematically categorize the design and fabrication techniques used in preparing MOF films, including in-situ growth, layer-by-layer assembly, and polymer-assisted strategies. The implications of MOF-based flexible electrochemical sensors are examined in the context of wearable devices, environmental monitoring, and healthcare diagnostics. Future research is anticipated to shift from traditional microcrystalline powder synthesis to MOF thin-film deposition, which is expected to not only enhance the performance of MOFs in flexible electronics but also improve sensing efficiency and reliability, paving the way for more robust and versatile sensor technologies.

Evaluating soil quality across various altitudinal gradients, both with and without vegetative cover, is crucial for the proper functioning of soil and optimal crop growth, thereby contributing to the sustainability of agroecosystems. Although the altitudinal gradient significantly influences soil quality, the ability to predict this quality, expressed through an index, in soils with and without vegetative cover, is still insufficiently explored. This study aimed to assess soil quality in the Jun Jun micro-watershed, located in the Tungurahua region, Ecuador. To achieve this objective, three categories of altitudinal gradients were selected: less than 2800 meters above sea level (masl), between 2800 and 2900 masl, and greater than 2900 masl. A total of 24 soil samples were collected in the mentioned gradients, considering both areas with and without vegetative cover. The indicators used included chemical and biological parameters such as soil organic carbon (OC), earthworm density (WD), earthworm biomass (WB), organic matter (OM), pH, total nitrogen (TN), and organic carbon (OC). The results revealed that in areas with altitudinal gradients below 2800 masl, soil quality index values were higher compared to other altitudes. In vegetated areas, a decrease in index values was observed as the altitudinal gradient increased, indicating a deterioration in soil quality with altitude. These findings are significant in providing a quantitative assessment of the effects of altitudinal gradient and vegetative cover influence on soil quality.

The Yangtze River is cross-linked with numerous lakes within its floodplain and is a worldwide biodiversity hotspot. There is no evidence indicating when this unique river-lake system developed. The endemic East Asian cyprinid clade has evolved diverse spawning adaptations to different flow conditions. Our ancestral egg-type reconstruction showed an ancestral state of adhesive eggs and later demersal eggs origination (both stream adaptations). Semi-buoyant eggs emerged ~18 Mya as a fast-flowing river adaptation, with increased hydration via three yolk protein degradation pathways, ion transport pathways and egg envelope permeability transition pores. Adhesive eggs evolved secondarily ~14 Mya with the egg envelope increasing to four layers and an adhesive layer, along with an increase in adhesiveness via microfilament/adhesive-related protein crosslinking and enhanced glycosaminoglycan biosynthesis, improving adherence to submerged lake plants, indicating that the cross-linked river-lake system formed in the mid-Miocene. This study provides a unique biological evidence for large-scale water system evolution.

The twisted Wang transform distribution family, defined as the composition of parameter shifted inverse CDF function with an original CDF function, is found to be most suitable for matching low shape factor distributions, characterizing hard to fit or to simulate reinsurance portfolio losses for some perils from our previous study. Among them, the best form for matching a hard-to-fit empirical loss distribution for a specific peril, is the Exponential Fractional Extra Power 0 Distribution in (0,1) with CDF:.The simplest yet still a good form of this family is the Transformed Hyperbolic Tangent Distribution with CDF:,which has analytical formulas for the moments. The twisted Wang transform distribution family is compared and confirmed to be superior to all other well-known distribution families through extensive numerical optimization practice, distribution forms guesses, and computer-aided exploration experiments.

Gas flaring is commonly used by industrial plants for processing oil and natural gases in the atmosphere, and hence is an important anthropogenic source for various pollutants including CO₂, CO, and aerosols. This study evaluates the feasibility of using satellite data to characterize gas flaring form space by focusing on the Khanty Mansiysk Autonomous Okrug in Russia, a region that is well known for its dominatingly gas flaring activities. Multiple satellite-based thermal anomaly data products at night are inter-compared and analyzed, including MODIS (Moderate Resolution Imaging Spectroradiometer) Terra level-2 Thermal Anomalies product (MOD14), MODIS Aqua level-2 Thermal Anomalies product (MYD14), VIIRS (Visible Infrared Imaging Radiometer Suite) Active Fires Applications Related Product (VAFP), and VIIRS level-2 data based Nightfire product (VNF). The analysis compares and contrasts the efficacy of these sensor products in detecting small, hot sources like flares on the ground in extremely cold environments such as Russia. We found that the VNF algorithm recently launched by NOAA has the unprecedented accuracy and efficiency in characterizing gas flares in the region owing primarily to the use of Shortwave Infrared (SWIR) bands. Reconciliation of VNF’s differences and similarities with other nighttime fire products is also conducted, indicating that MOD14/MYD14 and VAFP data are only effective in detecting those gas flaring pixels that are among the hottest in the region. Validation of VNF product of gas flaring location with Google Earth images are made. It is shown that that VNF’s estimates of gas flaring area (the area of gas flaming) agree well the counterparts from Google images with a linear correlation of 0.91, highlighting its potential use for routinely monitoring emissions of gas flaring from space.

The process of shock wave focusing can make the strength of shock waves be continuously accumulated and turned into detonation wave in Pulse Detonation Engine (PDE). However, its effective application needs the inlet jets be in high temperature and velocity, which is difficult to be satisfied under certain conditions. Therefore, in this paper, metal magnesium assisted detonation initiation is proposed and the effect of magnesium particle addition on the shock wave focusing process in a kerosene-fueled PDE with cavity configuration is investigated through numerical simulation. The result showed that when the temperature of the premixed fuel/air jets injected in opposite direction was set as 650 K, the collision of leading shock waves on the central axis was the main source of energy deposition and the shock wave focusing could make the detonation be initiated in the cavity. When the temperature of jets is reduced to 550 K, fuel ignition and detonation could not be achieved through shock wave focusing. Then adding metal magnesium particles into the combustor made the energy deposition be enhanced and the detonation be induced. The diffusion of metal particles can significantly change the structure, motion, merging and dissipation of vortices in the flow field. Generally, the shock wave focusing process is basically not affected with metal particles injection. Therefore, this method can be successfully employed for detonation initiation in the cavity when the fuel/air premixed jet temperature is not high for PDE.

The greatly diversified flowering plants (angiosperms) are the dominating and defining group in the current earth ecosystem. However, from which group by what way the flowers, especially their gynoecia (key characteristics of angiosperms), are derived have been the questions in botany unanswered over centuries. Such an embarrassing situation can be attributed to the lack of plants with partially enclosed ovules, which are supposed to be a post between gymnosperms and angi-osperms. Here we report a fossil plant that has an apparent coniferous vegetative and reproduc-tive morphologies but has a single seed partially wrapped by the subtending bract. Such a mor-phology suggests that the carpels in angiosperms may be equivalent to bracts enclosing their axil-lary seed(s). Such a non-traditional interpretation of the homology of angiosperm carpels is com-patible with various new progresses made in botany and is in line with Tomlinson’s recent hy-pothesis. Together with other fossil evidence reported recently, it appears that gynoecia in angio-sperms are derived in multiple ways.

Optical network monitoring and soft failure identification such as optical filter shifting and filter tightening is increasingly significant in the future complex and dynamic optical networks. Center frequency shift of optical filtering device in optical network has a serious impact on the perfor-mance of multi-span transmission, especially in high spectrum efficiency faster-than-Nyquist (FTN) transmission systems with various optical switching and add/drop nodes. Existing moni-toring schemes generally have problem of high cost, high complexity and the inability to realize multi-channel online monitoring, which makes it difficult to be applied in wavelength division multiplexing (WDM) system with numerous nodes. In this paper, a monitoring scheme of fre-quency shift of optical filtering devices based on optical label (OL) is proposed and demonstrated. The signal spectrum of each channel is intentionally divided into many sub-bands with corre-sponding optical labels loading. The characters of spectrum power changing caused by frequency shift can be reflected on labels power changing of each sub-band, which are used to monitor and estimate the value of frequency shift by DSP algorithm. Simulation results shows that the that the monitoring errors of frequency shift can be kept below 0.5GHz reasonably after 10-span WDM transmission in FTN polarization multiplexing m-ary quadrature amplitude modulation (PM-mQAM) systems. In addition, 250km fiber transmission experiments are also carried out and the similar results are obtained, which further verify the feasibility of our proposed scheme. The characters of low cost, high reliability and efficiency make it a better candidate for practical ap-plication in the future FTN WDM networks.

Lodging is a common problem in maize production that seriously impacts yield, quality, and the capacity for mechanical harvesting. Evaluation of site-specific lodging risks requires establishment of a method for multi-year monitoring. In this study, spectral images collected by the Sentinel-2 satellite were processed to obtain three types of data: gray-level co-occurrence matrix texture (GLCM), vegetation indices (VIs), and spectral reflectance (SR). Lodging classification models were then established with Random Forest (RF) using each of the three data types separately (the GLCM, VI, and SR models) and in combination (SR+VI model, SR+GLCM model, VI+GLCM mod-el, and SR+VI+GLCM model). By gradually removing features with low importance scores from the SR+VI+GLCM model and analyzing the changes in the overall accuracy (OA), the optimal set of predictive variables was identified and used to construct the optimal model. A model built us-ing data from a single timepoint in 2021 was tested on data collected at a similar timepoint in 2019 and vice versa to assess interannual model generalizability. The results of this study demon-strate that for monitoring maize lodging, models constructed with a single feature type, the GLCM model had significantly lower accuracy compared to the VI and SR models. During certain growth stages, the model constructed with combined features had significantly higher accuracy in monitoring maize lodging compared to models constructed with a single feature. During the pro-cess of selecting the optimal predictive variables, it was found that the accuracy of the model did not increase as the number of predictive variables increased. The results show that the positive and negative validation models had an accuracy of 96.55% and 95.18%, with kappa values of 0.93 and 0.83, respectively. This indicates that the model has strong generality for the same repro-ductive stage between years. This study provides a detailed method for large-scale maize lodging monitoring, allowing for identification of optimal planting practices to reduce the probability of lodging and ultimately improving regional maize yield and quality.

Stormwater management is a key urban issue in the world, in line with the global issues of urban sprawl and climate change. It is urgent to investigate the effectiveness in managing stormwater with different strategies for maintain urban resilience. A method based on a storm water management model (SWMM) was developed for assessing the control of stormwater runoff volume and the percentage removal of suspended solids by implementing a Sponge City strategy. An interdisciplinary approach was adopted incorporating Low Impact Development (LID) with urban Green Infrastructure and Gray Infrastructure paradigms in a typical old residential community in Suzhou, China. Four types of sponge facilities for reducing stormwater runoff were bio-retention cells, permeable pavements, grassed pitches, and stormwater gardens. The simulation results indicate that the stormwater pipe system can meet the management standard for storms with a five-year recurrence interval. The volume capture ratio of annual runoff is 91% and the reduction rate of suspended solids is 56%. This study demonstrates that Sponge City strategy is an effective approach for managing stormwater, particularly in old and densely populated urban areas. Implementing spongy facilities with a LID strategy for stormwater management can significantly enhance urban water resilience and increase ecosystem services.

Tack is one of the most important factors affecting the operability of prepregs, but it is still very difficult to obtain the change of prepreg tack with time at different temperatures. In this paper, a newly designed T-peel device is used to test the tack decay rate of prepregs at different temperatures. The obtained decay rate deviates less than 8.9% from the manufacturer's data. The maximum deviation of the ratio of tack decay speeds calculated by the Arrhenius equation from the experiments is not higher than -9.7%. It is proved that the present method can obtain the decay rate of tack of prepregs at different temperatures. This method is also applicable to the other two types of prepregs. The article proposes the handling life unit, an operational life measurement unit for prepregs, and establishes that the relationship between tack and remaining shelf life reduces prepreg management costs.

We present a new approach to retrieve Aerosol Optical Depth (AOD) from Moderate Resolution Imaging Spectroradiometer (MODIS) over the turbid coastal water. This approach supplements the operational Dark Target (DT) aerosol retrieval algorithm that currently don’t conduct any AOD retrieval in the regions with large water-leaving radiances in the visible spectrum. Over the global coastal water regions in all cloud-free conditions, this unavailability of AOD retrievals due to the inherent limitation in existing DT algorithm is ~20%. Here, we refine the MODIS DT algorithm by considering that water-leaving radiance at 2.1 μm is negligible regardless of water turbidity. This refinement, with the assumption that the aerosol single scattering properties over coastal turbid water are similar to that over the adjacent open-ocean pixels, yields ~18% more of MODIS-AERONET collocated pairs for six AEROENT stations in the coastal water regions. Furthermore, comparison with these AERONET observations show that the new AOD retrievals are in either equivalent or better accuracy than those retrieved by the MODIS operational algorithm (over coastal land and non-turbid coastal water). Combining the new retrievals with the existing MODIS operational retrievals not only yield an overall improvement of AOD over those coastal water regions, but also successfully extend the spatial and temporal coverage of MODIS AOD retrievals over the coastal regions where 60% of human population resides, and thereby, aerosol impacts on regional air quality and climate are expected to be significant.

With the gradual improvement of coal mining efficiency, the disturbance of groundwater system caused by the high-intensity mining mode also increases, which is a more severe challenge to the prevention of mine safety and the protection of water resources in mining areas. How to accurately describe the dynamic changes of the groundwater system under mining and quantitatively predict mine water inflow is a major problem in the current research. Based on the full analysis of the response characteristics of groundwater system to the extraction disturbance, this paper forms a kind of method to establish a mine hydrogeological conceptual model that can accurately represent the water inrush process, and uses the MODFLOW non-structural division grid to accurately characterize the formation structure, and finally make accurate water inflow prediction. Taking the Caojiatan Coal Mine in Shaanxi Province, China as an example, a numerical model of unstructured mine water inrush was established for the first time, and the changes of water inflow source and water inflow intensity were quantitatively evaluated. Compared with the traditional water inflow prediction method, it is found that the prediction accuracy is improved by 12%~17% by detailing the response characteristics of complex groundwater system under high-strength coal seam mining conditions. The method is of great significance and promotion value for the comprehensive understanding of the disturbance characteristics of human underground engineering activities, such as coal mining, on the groundwater system, and for accurately predicting water inflow.

Yaw misalignment can make a wake steer, which is an effective method to increase the power of wind farms, but it also increases the fatigue load of the turbines. In this paper, the method of combining yaw misalignment and pitch control (CYMP) is proposed to investigate the potential to mitigate wake interference, the wind velocity distribution and turbulence distribution in the wake, as well as the power and load changes of the wind turbine are studied, focusing on power in-crement and fatigue damage reduction. Although some studies have found that the method of CYMP are beneficial to increase power generation and reduce fatigue loads, there are no papers that have made a detailed analysis of the effects of wake turbulence, wind speed distribution, power, especially fatigue damage under this control. Simulation tool FAST.Farm is used to model and analyze wind farms, obtain the variation details of wake and provide simulation data for calculating power and fatigue load. The pitch control brings bias to the CYMP optimization results was neglected, the case studies show that the method of CYMP can reduce the fatigue load by 10.29% and increase the total power by 1.7% compared with only wake steering. The Model Predictive Control collaborative method based on CYMP is proposed, which can increase power by more than 2% and reduce thrust by more than 4% under 10m/s turbulent wind.

Investigating and classifying sentiments of social media users (e.g., positive, negative) towards an item, situation, and system are very popular among the researchers. However, they rarely discuss the underlying socioeconomic factor associations for such sentiments. This study attempts to explore the factors associated with positive and negative sentiments of the people about reopening the economy, in the United States (US) amidst the COVID-19 global crisis. It takes into consideration the situational uncertainties (i.e., changes in work and travel pattern due to lockdown policies), economic downturn and associated trauma, and emotional factors such as depression. To understand the sentiment of the people about the reopening economy, Twitter data was collected, representing the 51 states including Washington DC of the US. State-wide socioeconomic characteristics of the people (e.g., education, income, family size, and employment status), built environment data (e.g., population density), and the number of COVID-19 related cases were collected and integrated with Twitter data to perform the analysis. A binary logit model was used to identify the factors that influence people toward a positive or negative sentiment. The results from the logit model demonstrate that family households, people with low education levels, people in the labor force, low-income people, and people with higher house rent are more interested in reopening the economy. In contrast, households with a high number of members and high income are less interested to reopen the economy. The accuracy of the model is good (i.e., the model can correctly classify 56.18\% of the sentiments). The Pearson chi2 test indicates that overall this model has high goodness-of-fit. This study provides a clear indication to the policymakers where to allocate resources and what policy options they can undertake to improve the socioeconomic situations of the people and mitigate the impacts of pandemics in the current situation and as well as in the future.

Digital health has gained widespread adoption across various disciplines. Within the field of sport science, there is growing interest in digital health, leading to a surge in research activities. The objective of this study is to conduct a comprehensive bibliometric and visualization analysis, tracing the evolutionary trajectory, identifying research hotspots, and uncovering emerging trends in digital health within the domain of sport science. By doing so, this research aims to offer scholars a systematic and comprehensive understanding of the dynamic landscape in this field. To achieve this, the Web of Science core collection was chosen as the primary database. A thorough literature search was performed, focusing on digital health and sport science, resulting in the screening of 1870 English-language documents. The findings revealed a consistent upward growth trend in the annual publication count from 2010 to 2023. Notably, the United States, specifically the Commonwealth of Pennsylvania System of Higher Education, and John B. Cronin, emerged as the most prolific contributors in terms of publications. Collaborative efforts among countries, institutions, and authors were also observed. The research hotspots identified encompassed several areas, including the evaluation of digital health technologies' effectiveness, exploration of the relationship between digital health technologies and physical activity/exercise performance, and the use of digital health technologies in assessing and rehabilitating sports injuries. Among the prominent digital health technologies employed in these studies were virtual reality, social media, and wearable devices. The predominant types of studies utilized meta-analysis, randomized controlled trials, and cross-sectional studies. Looking towards the future, the study identified several key research trends. These include the exploration of telemedicine, artificial intelligence-based machine learning, therapeutic interventions, and physical therapy within the realm of digital health. These emerging areas signify promising directions for future investigation and development in the field of digital health within sport science.

In order to better plan new or update sewer pipe condition assessment protocols, this paper presents systematic comparisons of four most widely-used sewer condition assessment protocols, including the fourth edition of Sewer Rehabilitation Manual (SRM-4) in UK, Pipeline Assessment and Certification Program (PACP) in America, Sewer Physical Condition Grading Protocols (SPCCM) in Canada, and Technical Specification for Inspection and Evaluation of Urban Sewer (TSIEUR) in China. In qualitative comparison, the defects, deduct values and assessment methods of the four protocols were analyzed; in quantitative comparison, protocols were used to evaluate the same 182 sewer pipe segments based on field data and the assessment results were compared. It was found that SRM-4 are the most optimistic with 59% pipes being Grade 1 and Grade 2, while SPCCM gives the most pessimistic results with 62% pipes being Grade 3 and Grade 4. Assessment results by PACP and TSIEUR are in the middle. The main reasons for the different evaluation results were due to the different weight of defect and evaluation methods used.

This paper proposes a solution for the problem of mobile robot navigation and trajectory interpolation in dynamic environments with large scenes. The solution combines a semantic laser SLAM system that utilizes deep learning and a trajectory interpolation algorithm. The paper first introduces some open-source laser SLAM algorithms and then elaborates in detail on the general framework of the SLAM system used in this paper. Secondly, the concept of voxel is introduced into the occupation probability map to enhance the ability of local voxel maps to represent dynamic objects. Then, in this paper, we propose a PointNet++ point cloud semantic segmentation network combined with deep learning algorithms to extract deep features of dynamic point clouds in large scenes and output semantic information of points on static objects. A descriptor of the global environment is generated based on its semantic information. Closed-loop completion of global map optimization is performed to reduce cumulative error. Finally, T-trajectory interpolation is utilized to ensure the motion performance of the robot and improve the smooth stability of the robot trajectory. The experimental results indicate that the combination of the semantic laser SLAM system with deep learning and the trajectory interpolation algorithm proposed in this paper yields better graph building and loop closure effects in large scenes at SIASUN large scene campus. The use of T-trajectory interpolation ensures vibration-free and stable transitions between target points.

Differences in the physical and chemical properties of reclaimed water (RW) and natural surface water (SW) lead to the differences in terms of nitrogen and phosphorus release when pipeline sediments enter these water bodies. The nitrogen and phosphorus release kinetics from pipe sediments with different particle sizes have been investigated. The results demonstrated that both SW and RW had a pH buffering effect after sediment addition, and the final pH (approximately 8.1) of RW was lower. The release of total phosphorus (TP) and ammonia nitrogen ( NH₄⁺-N) fitted the first-order kinetic model where the release of TP reached equilibrium; TP release was inhibited in both SW and RW, where RW exhibited the lowest (by a factor of 1.23~2.44) release (0.002 mg/g). The release of NH4+-N was promoted in both SW and RW; the maximum release in RW was 0.0188 mg/g. The amounts of NH₄⁺-N released in SW and RW were 1.02-1.40 and 1.30-1.80 times that of the control group (CG), respectively. The percentage of TP and NH₄⁺-N release in the three groups was highest in 75-154 μm pipe sediment, reaching 34.53% and 43.51% in SW and RW, respectively. These results can assist in the development of water quality evolution models for specific urban scenarios, and provide important guidance for the precise regulation of recharge water quality during and after rainfall.

Topology optimization is a pioneering design method that can provide various candidates with high mechanical properties. However, the high-resolution for the optimum structures is highly desired, normally in turn leading to computationally intractable puzzle, especially for the famous Solid Isotropic Material with Penalization (SIMP) method. In this paper, an efficient and high-resolution topology optimization method is proposed based on the Super-Resolution Convolutional Neural Network (SRCNN) technique in the framework of SIMP. The SRCNN includes four processes, i.e. refining, path extraction & representation, non-linear mapping, and reconstruction. The high computational efficiency is achieved by a pooling strategy, which can balance the number of finite element analysis (FEA) and the output mesh in optimization process. To further reduce the high computational cost of 3D topology optimization problems, a combined treatment method using 2D SRCNN is built as another speeding-up strategy. A number of typical examples justify that the high-resolution topology optimization method adopting SRCNN has excellent applicability and high efficiency for 2D and 3D problems with arbitrary boundary conditions, any design domain shape, and varied load.

The current outbreak of coronavirus disease (COVID-19) caused by SARS-CoV-2 in Wuhan, China has killed more than 2600 people since December 2019. Currently there is no effective treatment for this epidemic. Drug for anti SARS-CoV-2 are urgently needed. In this study we evaluated two compound libraries containing launched drugs and compounds from 300 kinds of Traditional Chinese Medicine in order to find anti SARS-CoV-2 drugs. Docking and then calculating binding free energy were performed as workflow against four key anti-SARS-CoV-2 drug targets, 3CLpro, PLpro and RdRp from SARSCoV-2, and AAK1 from human as well. As a result, drugs launched with potential for antiviral usage were selected in the hope of providing some knowledge for future drug discovery.

Geological structures such as joints and faults in rock mass have significant influence on open pit mining. Hence, it is critical to develop a understanding of dynamic joint behaviour under blasting loading. This in turn can provide both theoretical and practical guidance to improve blasting rock fragmentation and associated bucket excavating efficiency. In this paper, delayed blasting on the highwall bench at Baiyunebo open-pit mine was used as an example, a nonlinear joint blasting model was also constructed. By simplifying the blasting wave propagation velocity, the P-wave normal incidence to the joint was obtained. The peak vibration velocity was 0.33m/s at 3.0s. The S-wave reflected by the joint interface was first reflected backward and then forward, which the peak vibration velocity was 0.027 m/s. By combining the relevant stress and displacement theories of type I and II cracks, the equipotential diagrams of the stress and displacement field with the vibration velocity of the particle were obtained. σx was positive in the direction of 0~330° and subjected to tensile stress, whereas σy was positive in the direction of 0~180° and under tensile stress. The longitudinal σy along joint was low in compressive stress distribution area and did not affect surrounding rock at the time. The stress concentration appeared in the lower right corner. Based on the continuous behavior of stress wave in joints, the asymmetry and continuous changes reflected in the whole process could not be analysed by the contour diagram. Hence, ANSYS used to analyse distribution of the stress field. The intensity of the shock wave after detonation was greater than that of the rock strength. Subsequently, the sub-layer shock wave supplemented the shock wave energy that was not enough to break the rock and induced further cracking. This was able to be visualized by the degree of color change post-processing. It was concluded that with the attenuation of the detonation wave energy, the stress exhibited a decreasing trend in this process. According to distribution of the peak effective stress, it was found that the peak value first increased to 10-12 MPa and then showed a downward trend. Overall, the results were validated against the finite element simulation and mathematical analysis.

Different inlet structures have a significant impact on the internal flow characteristics of a solid-magnesium powder water ramjet engine. Based on the magnesium-water reaction model, a computational fluid dynamics (CFD) method is applied to establish a numerical simulation method for the internal flow field of the engine, and the internal flow characteristics of the engine under different inlet structure conditions are studied. The simulation results show that high-temperature gas can effectively promote the ignition of magnesium powder at the top of the combustion chamber, while accelerating the evaporation of the first inlet water and increasing the combustion rate of magnesium powder. The secondary inlet has the most significant effect on the temperature inside the combustion chamber. When the secondary inlet flow rate increases towards the top of the combustion chamber, it increases the amount of heat absorbed by the evaporating water at the top of the chamber, thereby reducing the temperature at the top of the combustion chamber. However, when the flow rate is low, it results in insufficient oxidizer at the top of the combustion chamber, which is unfavorable for the combustion of magnesium powder.

Three new compounds (1, 11 and 12), together with 32 known ones, were isolated from the root bark of Morus alba L. using various chromatographic methods. The structures of the undescribed compounds were elucidated based on 1D, 2D NMR and HRESIMS data analysis, while the known ones were identified by comparison of their spectroscopic data with those reported in the literature. All the isolates were evaluated for their cytotoxic activities against human gastric cancer HGC27 cells by CCK-8 assay. Among them, compounds 5, 8, 10 and 30 exhibited cytotoxic activities on HGC27 cells with IC50 values of 10.24 ± 0.89 μM, 28.94 ± 0.72 μM, 6.08 ± 0.34 μM and 33.76 ± 2.64 μM, respectively. Furthermore, compound 10 was confirmed to reduce proliferation ability, increase apoptosis rate and inhibit cell migration pathway by annexin V/PI double staining experiment, transwell experiment and western blot analysis.

Kombucha is a popular sparkling sugared tea, fermented by a symbiotic culture of acetic acid bacteria (AAB) and yeast. The demand for Kombucha is increasing worldwide mainly due to its perceived health benefits and appealing sensory properties. This study isolated and characterised the dominant AAB and yeast from starter culture and Kombucha broth after 0, 1, 3, 5, 7, 9, 11, and 14 days of fermentation at ambient temperature (~22°C). Changes in the microbial composition were associated with variations in the physico-chemical characteristics of Kombucha tea, such as pH, titratable acidity, and total soluble solids (TSS). During fermentation, the acidity increased, and TSS decreased. The yield, moisture content and water activity of the cellulosic pellicles which had developed by the end of fermentation were attributed to the presence of AAB. Yeast and AAB were isolated from the Kombucha samples using glucose yeast extract mannitol ethanol acetic acid (GYMEA) and yeast extract glucose chloramphenicol (YGC) media respectively, using serial dilutions. Phenotypic and taxonomic identification of AAB and yeast were determined by morphological and biochemical characterisation, followed by sequence analysis of the ribosomal RNA gene (16S rRNA for AAB and ITS for yeast). The dominant AAB species in the cellulosic pellicle and Kombucha broth was identified as Komagataeibacter rhaeticus. The yeast isolates belonged to Debaryomyces prosopidis and Zygosaccharomyces lentus.

Interface solar steam generation (ISSG) are charming for its applications in desalination and wastewater treatment. Biomass is an attractive substrate for utilizing solar vapor evaporators because of its natural pore structure and water transportability. Polymers like polydopamine (PDA) and polypyrrole (PPy) with broadband spectrum absorption are fascinating in photothermal materials (PTMs). Herein, PDA coated daikon-based (PDA-DK) and PPy coated daikon-based (PPy-DK) PTMs have been exploited for solar steam generation. When polyethylene foam (PEF) was used as an insulating layer to limit heat loss from the PTMs to bulk water, the evaporation rate of PDA-DK and PPy-DK was raised from 0.82 kg m–2 h–1 and 0.96 kg m–2 h–1 to 1.50 kg m–2 h–1 and 1.60 kg m–2 h–1, respectively. Meanwhile, the corresponding photothermal conversion efficiency was increased to 89.01% and 98.97%, which was increased by nearly 40% under 1-sun irradiation. In addition, PDA-DK and PPy-DK exhibited remarkable stability for the solar steam generation without significant change through 15 cycles. Furthermore, PDA-DK and PPy-DK could effectively desalt seawater and purify dyeing wastewater. All the results indicate that PDA-DK and PPy-DK have great potential in real-world applications for solar steam generation.

Water resources are threatened nowadays by pollution that comes from domestic, industrial and agricultural discharges without prior treatment. This pollution causes the degradation of water quality. Surface pollutants can seep through the soil into water tables. The objective of our work is to assess and control the physicochemical quality of the Chari Baguirmi groundwater, to protect human health. The quality of 83 boreholes was assessed, while performing analysis for 12 physicochemical parameters at the National Water Laboratory and at the Center for Quality Control of Foodstuffs in Chad. These parameters are: pH, EC, Ca2+, Mg2+, Na+, K+, Cl-, SO42-, NH4+ and NO3- , Fe2+ and HCO3-. Also, the results obtained were compared with WHO standards. The geochemical statistical approach has made it possible to characterize the hydro geochemical properties and to understand the major processes of the mineralization of groundwater resources in Chari Baguirmi region in Chad. Some of its waters are acidic and weakly mineralized, rich in Fe2+ and NH4+. The origin of the mineralization is due to the alteration of the host rocks and to the hydrolysis of silicate and ferromagnesian minerals as well as anthropogenic pollution. The ammonium concentrations in N’Djamena boreholes are higher than WHO standards, indicating the presence of pollution which may come from organic waste. These results constitute a preliminary step in understanding hydro geochemical functioning and a basis for monitoring the physicochemical quality of the water in the study area.

In autonomous driving systems, high-speed and real-time image processing, along with object recognition, are crucial technologies. This paper builds upon the research achievements in in-dustrial item sorting systems and proposes an object recognition and sorting system for auton-omous driving. In industrial sorting lines, goods sorting robots often need to work at high speeds to efficiently sort large volumes of items. This poses a challenge to the robot's real-time vision and sorting capabilities, making it both practical and economically viable to implement a real-time and low-cost sorting system in a real-world industrial sorting line. Existing sorting systems have limitations such as high cost, high computing resource consumption, and high power consump-tion. These issues lead to the fact that existing sorting systems are typically used only in large industrial plants. In this paper, we design a high-speed, low-cost, low-resource-consumption FPGA (Field-Programmable Gate Array) based item sorting system that achieves similar perfor-mance to current mainstream sorting systems at a lower cost and consumption than existing sorting systems. The recognition part employs a morphological recognition method, which segments the image using a frame difference algorithm and then extracts the color and shape features of the items. To handle sorting, a six-degree-of-freedom robotic arm is introduced in the sorting segment. The improved cubic B-spline interpolation algorithm is employed to plan the motion trajectory and consequently control the robotic arm to execute the corresponding actions. Through a series of experiments, this system achieves an average recognition delay of 25.26ms, ensures smooth operation of the gripping motion trajectory, minimizes resource consumption, and reduces implementation costs.

Over the past four decades, China has experienced a nutritional transition and has developed the largest population of internet users. In this study, we evaluated the impacts of internet access on the nutritional intake in Chinese rural residents. An IV-Probit-based propensity score matching method was used to determine the impact of internet access on nutritional intake. The data were collected from 10042 rural households in six Chinese provinces. The results reveal that rural residents with internet access have significantly higher energy, protein, and fat intake than those without. Chinese rural residents with internet access consumed 1.35% (28.62 kcal), 5.02% (2.61 g), and 4.33% (3.30 g) more energy, protein, and fat, respectively. There was heterogeneity as regards the intake of energy, protein, and fat among those in different income groups. Moreover, non-staple food consumption is the main channel through which internet access affects nutritional intake. The results demonstrate that the local population should use the internet to improve their nutritional status. Further studies are required to investigate the impact of internet use on food consumed away from home and micronutrients intake.

The effects of acidic electrolyzed water (AEW) on the microbiological and physicochemical properties of fresh-cut red cabbages were studied. The fresh-cut red cabbages and artificially inoculated red cabbages with Salmonella Typhimurium DT104 were washed with distilled water (DW) and different available chlorine concentration (ACC) of AEW for different times. AEW treatments significantly reduced the populations of native aerobic bacteria, molds and yeasts, and artificially inoculated S. Typhimurium DT104 compared to the DW treated and untreated red cabbage samples. The effectiveness of AEW treatments was greatly enhanced with increasing ACC and treatment times. S. Typhimurium DT104 were not detected in the washing water after the red cabbages treated by AEW. The surface color, pH, and total phenolic contents were did not significantly change when the red cabbages were washed with DW and 100 ppm AEW for 3 min. The anthocyanin contents and antioxidant activities of red cabbage were significantly reduced by 18.5% for cyanidin, 22.1% for pelargonidin, and 11.2% for DPPH radical scavenging activity, the impacts on the nutritional benefits of red cabbage were considered as limited and acceptable. The optimal process condition of AEW for washing red cabbage was 100 ppm for 3 min. In these conditions, most of the native microflora were inactivated, and artificial inoculated S. Typhimurium DT104 on the red cabbage were reduced by 40.2% (3.67 log CFU/g) and with minimal losses of nutrients and antioxidant activity, as well as no requirement of discontinuation treatment on the washing water.

Ni-rich layered cathodes are regarded as a potential candidate for high energy-density lithium-ion batteries, but their high sensitivity to air during storage and poor thermal stability are a vital challenge for large-scale applications. In this paper, an effective solid-solution strategy was proposed to improve the surface and structural stability of Ni-rich layered cathodes by introducing Li2MnO3. The structural analysis results indicate that the formation of Li2CO3 inert layers on Ni-rich layered cathodes during storage in air is responsible for the increased electrode interfacial impedance, thereby resulting in the severe deterioration of electrochemical performance. The introduction of Li2MnO3 can reduce the surface reactivity of Ni-rich cathode materials, playing a certain suppression effect on the formation of surface Li2CO3 layer and the deterioration of electrochemical performances. Additionally, the thermal analysis results show that the heat release of Ni-rich cathodes strongly depends on the charge of states, and Li2MnO3 can suppress oxygen release and significantly improves the thermal stability of Ni-rich layered cathodes. This work provide a method to improve the storage performance and thermal stability of Ni-rich cathode materials.

Photovoltaic(PV) power generation is highly nonlinear and stochastic. Accurate prediction of PV power generation plays a crucial role in grid connection as well as the operation and scheduling of power plants. To predict the PV power combination model, this paper suggests a method based on Empirical Mode Decomposition (EMD), Ensemble Empirical Mode Decomposition (EEMD), Complete Ensemble Empirical Mode Decomposition with Adaptive Noise (CEEMDAN), Nonlinear Auto-Regressive Neural Networks with Exogenous Input (NARXNN), Long Short Term Memory (LSTM) Neural Network, and Light Gradient Boosting Machine (LightGBM) algorithms. To attempt to reduce the non-smoothness of PV power, the weather variable features with the greatest effect on PV power are first identified by correlation analysis. Following this, the PV power modal decomposition is split and reorganized into a new feature matrix. Finally， a NARX is used to obtain preliminary PV power components and residual vector features， and the PV power is predicted by combining three models of LightGBM， LSTM, and NARX and then the final prediction results are obtained by combining the PV power prediction results using error inverse method weighted optimization. The prediction results demonstrate that the model put forth in this paper outperforms those of other models and validate the model's validity by utilizing real measurement data from Andre Agassi College in the United States.

Raindrop size distribution (RSD) is an index for reflecting precipitation characteristics. Analyzing the differences of RSD plays an important role in understanding the precipitation microphysical processes and improving quantitative precipitation prediction of radar. In this paper, the RSD data of Dafang (57708) station, Majang (57828) station, and Luodian (57916) station (with an altitude of 1722.7m, 985.0m, and 441.5m, respectively) in Guizhou are analyzed according to the precipitation microphysical characteristics. First,Particles with particle size less than 1mm contributes the highest value to the density of particle number , and decrease with the descending altitude. Second, the GAMMA distribution fit shows a better fit compare to M-P distribution fit, and GAMMA distribution fit increases with the ascending altitude. Third, the mass-weighted average diameter is not sensitive enough to the change of precipitation intensity with correlation coefficients of 54.84%, but there is a obvious relationship between the average volume diameter and the precipitation intensity with correlation coefficients of 69.15%. Then, the precipitation prediction model is established using LSTM neural network after fusing the representative microphysical characteristics of RSD with radar and rain gauge data. The precipitation prediction model is applied to the Dafang (57708) site to predict precipitation for time range of 0-180 minutes, and it is found that for the prediction of convective cloud and stratiform cloud precipitation, the 60-minute prediction results are the most consistent with the actual precipitation, where the correlation coefficients are 92.87% and 92.57%, respectively. Conclusively, the results demonstrate that combining with the RSD base data could improve the reliability of precipitation forecasting.

Cadmium(Cd) is a highly toxic and cumulative environmental pollutant. Siderophores are heavy metal chelators with high tolerance to heavy metals such as Cd. Furthermore, ryegrass (Lolium perenne L.) has potential remediation capacity for soils contaminated by heavy metals. Consequently, using ryegrass alongside beneficial soil microorganisms that produce siderophores may be an effective means to remediate soils contaminated with Cd. In this study, Bacillus strains WL1210 and CD303 that were previously isolated from the rhizospheres of Nitraria tangutorum in Wulan and Peganum harmala L in Dachaidan, respectively, both arid sandy environments, were evaluated for heavy metal pollution mitigation. The results indicate that both strains of Bacillus exhibit favorable biological characteristics and stress resistance, and they are both producers of siderophores, which promote the growth of ryegrass under Cd stress.

Background Acute kidney injury (AKI) is a common comorbidity in the intensive care unit (ICU), with higher mortality rate among those who receive continuous renal replacement therapy (CRRT). This study aimed to investigate the association of white blood cell (WBC) levels with all-cause mortality in AKI patients undergoing CRRT. Method We conducted a post hoc analysis of ICU patient data from multiple centers in Korea. First, the levels of WBCs were classified into four groups based on quartiles. Second, the relationship between different WBC levels and mortality was investigated with the Kaplan-Meier (K-M) survival curves, Cox proportional hazards model, and generalized additivity model (GAM). Finally, we used multiple imputation to avoid bias caused by non-randomized missing data. The endpoints were short-term (28 days) and long-term (90 days) mortality. Result In our analysis, a total of 1,100 ICU patients were included. Among them, 670 (60.90%) and 781 (71.00%) died within 28 and 90 days, respectively. K-M survival curves showed that patients with the lowest WBC levels had the highest risk of mortality for both outcomes. Adjusted multivariate Cox regression analysis confirmed that compared with the reference level (quartile 2), low WBC levels increased the risk of both 28-day mortality (quartile 1, HR = 1.43, 95% CI: 1.13–1.83, P = 0.004) and 90-day mortality (quartile 1: HR = 1.32; 95% CI: 1.05-1.66, P = 0.016). GAM analysis showed a non-linear, U-shaped relationship between pre-CRRT WBC levels and all-cause mortality (non-linear P < 0.05). Conclusion The baseline WBC level is an independent predictor of prognosis for ICU patients receiving CRRT. Patients in the lowest WBC quartile had the highest risk of all-cause mortality. These results provide further evidence that early observation and intervention may have a prognostic value for these high-risk patients.

Large-scale farms are pivotal sites for the development of the agricultural industry, and the quality of the ecological environment is a significant factor affecting the growth of cereal crops. Consequently, assessing the ecological quality of large-scale farms is of great importance. This paper leverages the advantages of remote sensing imagery for long-term, quantitative, and dynamic monitoring of ecological quality over extensive areas. It develops an ecological assessment procedure suitable for agricultural regions based on an Improved Remote Sensing Ecological Index (IRSEI), which considers the coupling of ecosystem component elements. This procedure introduces a Pan-Salinity Index (PSI) tailored to the characteristics of soil salinization in farming areas and incorporates an ecological greenness index based on the Normalized Difference Vegetation Index (NDVI), an ecological humidity index derived from the K-T transform (WET), an ecological dryness index synthesized from the bare soil index and the built-up index (NDBSI), and an ecological heat index represented by the Land Surface Temperature (LST) calculated from atmospheric parameter models. These five indices are integrated into the ecological assessment system. The experimental results visually demonstrate the development and changes of ecological impact factors in the farm research area over the past decade, as well as the spatiotemporal variations in the quality of the farm's ecological environment. The findings indicate that between 2010 and 2019, the overall trend of IRSEI first declined, then rose, and subsequently experienced a slight decrease. Through differential analysis, regions and areas with declining ecological quality were identified, providing a data reference for the formulation and implementation of future ecological protection and management measures for the farm. The proposed IRSEI method offers a rapid and effective new monitoring approach for agricultural planting areas with a tendency towards soil salinization.

Extraction of high-resolution surface waves is essential in surface-wave survey. Because reflections usually interfere with surface waves on X component in a multicomponent seismic exploration, it is difficult to extract dispersion curves of surface waves. The situation goes more serious when the frequencies and velocities of higher-mode surface waves are close to those of PS-waves. A method for surface-wave extraction is proposed based on the morphological differences between reflections and surface waves. Frequency-domain high-resolution linear Radon transform (LRT) and time-domain high-resolution hyperbolic Radon transform (HRT) are used to represent surface waves and reflections respectively. Then, the sparse representation problem based on the morphological component analysis (MCA) is built and optimally solved to obtain high-fidelity surface waves. An advantage of our method is its ability to extract surface waves when their frequencies and velocities are close to those of reflections. Furthermore, results of synthetic and field examples confirm that the proposed method can attenuate the distortion of surface-wave dispersive energy caused by reflections, which contributes to extracting accurate dispersion curves.

During public health events, Active Mobility (walking and cycling) plays an important role in securing residents' travel. To enhance the resilience of urban transportation, this article integrates the travel environment elements for walking and cycling and constructs a travel environment for Active Mobility evaluation index system. This article uses survey data from the main urban area of Harbin in the context of the COVID-19 pandemic in May 2022, and combines the Gradient Boosting Decision Tree (GBDT) and Impact-Asymmetry Analysis (IAA) methods to analyze the satisfaction of the travel environment for Active Mobility. It proposes strategies for optimizing the travel environment for Active Mobility, ensuring residents' travel during public health events, guiding them to adopt Active Mobility, and improving urban transportation resilience. This research shows that Active Mobility can enhance urban transportation resilience. In addition, there are differences in resident demand for walking and cycling environments in the travel environment for Active Mobility. Residents are more concerned about the comfort of the walking environment, while they prioritize the convenience of the cycling environment.

Natural products are an important source of antibacterial agents. Canthin-6-one alkaloids have displayed potential antibacterial activity based on our previous work. In order to improve the activity, twenty-two new 3-N-benzylated 10-methoxy canthin-6-ones were designed and synthesized through quaternization reaction. The in vitro antibacterial activity against three bacteria was evaluated by double dilution method. Four compounds (6f, 6i, 6p and 6t) displayed 2-fold superiority (minimum inhibitory concentration (MIC) = 3.91 µg/mL) against agricultural pathogenic bacteria R. solanacearum and P. syringae than agrochemical propineb. Moreover, the structure–activity relationships (SARs) were also carefully summarized in order to guide the development of antibacterial canthin-6-one agents.

The accumulation of foam cells in arterial intima and the accompanied chronic inflammation are considered major causes of neoatherosclerosis and restenosis. However, both the underlying mechanism and effective treatment for the disease are yet to be uncovered. In this study, we combined transcriptome profiling of restenosis artery tissue and bioinformatic analysis to reveal that NLRP3 inflammasome is markedly upregulated in restenosis and that several restenosis re-lated DEGs are also targets of mulberry extract, a natural dietary supplement used in traditional Chinese medicine to improve liver vitality. Further pathway enrichment analysis identified MAPK signaling pathway to be involved in the inflammatory response of foam cells. Consistently, immunofluorescence microscopy shows co-localization of NLRP3 with CD68+ macrophages. We then evaluated the efficacy of mulberry extract in inhibiting both the formation of foam cells and their inflammatory response. We demonstrated that mulberry extract suppresses the formation of ox-LDL induced foam cells, possibly by upregulating the cholesterol efflux genes ABCA1 and ABCG1 to inhibit intracellular lipid accumulation. In addition, mulberry extract dampens NLRP3 inflammasome activation by stressing the MAPK signaling pathway. Collectively, our mecha-nistic and functional studies unveil the therapeutic value of mulberry extract in neoatherosclerosis and restenosis treatment by regulating lipid metabolism and inflammatory response of foam cells.

In order to improve the operation performance of the multi-stage double-suction centrifugal pump and reduce the internal energy loss of the pump, this paper proposes a single-objective optimization design method based on non-hierarchical response surface model (RSM) and the multi-island genetic algorithm (MIGA). Nine parameters, such as the blade outlet width and blade wrap angle, were used as design variables, and the optimization objective was the efficiency under design conditions. In total, 149 sets of valid data were obtained under the latin hypercube sampling method (LHS), the corresponding thresholds were set for efficiency and head, and 99 sets of valid data were obtained. A cross-validation analysis of the sieved data was carried out based on non-hierarchical RSM, global optimization of the efficiency was carried out using MIGA, and numerical verification was carried out via CFD. The research results show that compared with hierarchical RSM, non-hierarchical RSM can approximate the nonlinear relationship between the objective function and the design variables with higher accuracy, and the model fitting R2 value was 0.919. The efficiency was improved by 3.717% after optimization. The overall prewhirl of the impeller inlet after optimization decreased, the internal speed of the volute significantly improved, the large-area vortex at the volute and the outlet pipe was eliminated, the impact loss at the volute separating tongue disappeared, and the overall hydraulic performance of the pump was improved. The total entropy output value of the optimized pump was reduced by 4.79 (W/K), mainly concentrated in the reduction in the entropy output value of the double volute, and the overall energy dissipation of the pump was reduced.

It is a critical issue to allocate redundancy to critical smart grid infrastructure for disaster recovery planning. In this study, we present a framework to combine statistical prediction methods and optimization models for the optimal redundancy allocation problem. First, we develop statistical simulation methods to identify critical nodes of very large-scale smart grid infrastructure based on the topological features of embedding networks, and then present a linear integer programming model based on generalized assignment problem (GAP) for redundancy allocation of critical nodes in smart grid infrastructure. The model is specifically implemented in the context of smart grid infrastructure. The findings demonstrate that the combined approach of statistical simulation and optimization effectively addresses the size limitations inherent in a sole optimization approach. Notably, the optimal solutions for redundancy allocation in very large grid systems highlight that the cost of redundancy is only a fraction of the economic losses incurred due to weather-related outages.

Due to the intermittency and fluctuation of photovoltaic (PV) output power, a high proportion of grid-connected PV power generation systems has a significant impact on power systems. Accurate PV power forecasting can alleviate the uncertainty of the PV power and is of great significance for the stable operation and scheduling of the power systems. Therefore, in this study, a feature rise-dimensional (FRD) two-layer ensemble learning (TLEL) model for short-term PV power deterministic forecasting and probability forecasting is proposed. First， based on the eXtreme Gradient Boosting (XGBoost), Random Forest (RF), CatBoost, and Long-short-term memory (LSTM) models, a TLEL model is constructed utilizing the ensemble learning algorithm. Meanwhile, the FRD method is introduced to construct the FRD-XGBoost-LSTM (R-XGBL), FRD-RF-LSTM(R-RFL), and FRD- CatBoost - LSTM (R-CatBL) models. Subsequently, the above models are combined to construct the FRD-TLEL model for deterministic forecasting, and perform probability interval forecasting based on quantile regression(QR). Finally, the performance of the proposed model is demonstrated with a real-world dataset. By comparing with other models, the proposed model displays better forecasting accuracy for deterministic forecasting and reliable forecasting intervals for probability forecasting, and good generalization ability in the datasets of different seasons and weather types.

(1) Background: There is a risk of Aflatoxin B1(AFB1) pollution in yellow rice wine[1],threatening human life and health, the risk is a major focus of government attention and social concern.The current detection technology cannot meet the needs of large-scale testing due to the disadvantages of high false positive, cumbersome operating procedures or high cost.Therefore, it is urgent to study and establish a high-sensitivity and high-fast detection method for AFB1 to provide technical support for yellow rice wine quality supervision and risk assessment.; (2) Methods: In this study, three-factor and three-level orthogonal experiments were carried out for oscillation time, reaction temperature and tomography time to determine the best reaction conditions for pretreatment.AFB1 detection was carried out by aflatoxin time-resolved fluorescence immunochromatography technology，Through the ratio of the T signal value of the detection line to the C signal value of the quality control line and the natural logarithmic value of the standard solution concentration[2], a rapid detection technology of time-resolution fluorescence immunochromatography is established.The technology was methodically assessed, the actual yellow rice wine samples were tested, and the results were compared with the HPLC method; (3) Results: The results show that the optimal reaction conditions for pretreatment are: the sample oscillation time is 20min, the sample reaction temperature is 37°C, and the sample chromatography time is 6min. In the actual sample detection of yellow rice wine, The time-resolved fluorescence immunochromatography detection technology established in this study detects AFB1. The detection limit is 0.3 μg·kg-1,The linear range is 0.8-12.0μg·kg-1,The linear equation of the corresponding standard curve y=-0.1913x+0.5206 (R2=0.9948),The standard deviation is 0.029.The results of the in-batch accuracy and precision of this method show that the addition and recovery rate is 77.9% - 105.7%,The coefficient of variation is in 4.5% - 10.3%; Inter-batch accuracy and precision test results show that the addition recovery rate is75.9% - 85.8%,the coefficient of variation is in 8.1% - 13.9%,explain that the detection technology has good accuracy and precision.Compared with HPLC, the relative error is less than 10%,It shows that aflatoxin time-resolution fluorescence immunochromatography technology is in good agreement with the test results of national standard methods; (4) Conclusions:he rapid detection technology of time-resolution fluorescence immunochromatography of AFB1 in yellow rice wine is easy to operate with fast detection speed, high sensitivity, good repeatability and stability, and has broad application prospects.

The separation of Li+ and [Bmim]+(1-Butyl-3-methylimidazolium) by electrically driven membrane technology was studied. The effects of the types and modification processes of cation exchange membranes, current density, total cation concentration, temperature, and anion types on separation efficiency were investigated. The results indicated that it is feasible to achieve efficient separation of Li+ and [Bmim]+ using the selectivity of cation exchange membranes under electric field. Membrane CMX and the modified membrane A and B which obtained from the CMX showed obvious selective of Li+ from [Bmim]+. When the current density is 5 mA/cm2 and the feed concentrations of Li+ and [Bmim]+ are 0.3 mol/L and 0.2 mol/L, the selective transport coefficient of the modified membrane B can reach 6.2 in the first 120 minutes of the process. Reducing current density and increasing total cation concentration can improve separation efficiency. Lowering the temperature can improve the separation effect, but improvement is not obviously. Changing the anion of the feed from chloride ion to acetate has no effect on the separation.

CuO/ZnO/Al2O3 catalyst is a commonly used catalyst for rea methanol steam reforming reaction. Oxalic acid was as precipitant in preparing oxalate precursor of CuO/ZnO/Al2O3 catalyst by co-precipitation, deionized water and ethanol were as solvents, microwave irradiation and water bath were as aging heating manner respectively. It indicated that ethanol selected crystal phase composition of oxalate precursors and restricted their growth. Microwave irradiation prompted the isomorphous substitution between Cu2+ of CuC2O4 and Zn2+ of ZnC2O4 in mother liquid, forming the master phase (Cu,Zn)C2O4 in precursor, the solid solution Cu-O-Zn formed after calcination, which exhibited nano-fibriform morphology. It possessed small CuO grains, large surface area and strong synergy between CuO and ZnO, which is beneficial to improve the catalytic performance of methanol steam reforming, the STY of H2 reached 516.7 mL·g-1·h-1, and the selectivity of CO was only 0.29%.

Foxtail millet, a traditional cereal crop, has gained increasing attention for its high nutritional value and potential health benefits. This study aimed to investigate the simultaneous and rapid detection of amylose and amylopectin content of foxtail millet flour under different sheep manure application rates by hyperspectral imaging combined with chemometrics. The spectral data preprocessing used multiplicative scatter correction (MSC), and the combined algorithm of competitive adaptive reweighted sampling (CARS), random frog (RF), iterated retaining informative variables (IRIV) were employed for key band extraction. The partial least squares regression (PLSR) was then used to establish the prediction model and the regression equation, that was used to visualize the two components. Results demonstrated the key band extraction combined algorithm effectively reduced data dimension without compromising the accuracy of the prediction model. The prediction model for amylose using MSC-RF-IRIV-PLSR exhibited good performance, with the correlation coefficient (R) and root mean square error (RMSE) predicted to be 0.73 and 1.23, respectively. Similarly, the prediction model for amylopectin using MSC-CARS-IRIV-PLSR also demonstrated good performance, with the R and RMSE predicted to be 0.59 and 7.34, respectively. Then, the visualization graph generated clearly shows under the condition of applying 6 m3 of sheep manure, the amount of amylopectin accumulation was highest, and the amount of amylose was lowest. The experimental results offer valuable insights for the rapid detection of nutritional components in foxtail millet, serving as a basis for further research.

The transforming growth factor-β (TGF-β), in which overexpression have been associated with various diseases, has become an attractive molecular target for the treatment of cancers. Three series of 3-substituted-4-(quinoxalin-6-yl) pyrazoles 14a–h, 15a–h, 16a–h, 22a, 22b, 22d, 23a, 23b, 23d, 24b, and 24d were synthesized and evaluated for their activin receptor-like kinase 5 (ALK5) and p38α mitogen activated protein (MAP) kinase inhibitory activity in an enzymatic assays. Among these compounds, the most active compound 16f inhibited ALK5 phosphorylation with an IC₅₀ value of 0.28 µM, with 98% inhibition at 10 µM. Compound 16f also had good selectivity index of >35 against p38α MAP kinase, with 9.0-fold more selective than clinical candidate, compound 3 (LY-2157299). Molecular docking study was performed to identify the mechanism of action of the synthesized compounds and their good binding interactions were observed. ADMET prediction of good active compounds showed that these ones possess good pharmacokinetics and drug-likeness behavior.

Previous research via cell experiments has shown that ultrafine particles (UFPs, particles less than 100 nm) emitted from Three-Dimensional desktop printers (3D printers) had cytotoxicity. However, a few particles from different filaments and their cytotoxicity combinations have been tested. Here we quantify emissions of UFPs and use Air-Liquid Interface (ALI) from one commercially available filament extrusion desktop 3D printer utilizing three different filaments by controlled experiments. A549 cells were exposed at the ALI to UFPs generated by a working 3D printer for an average of 45 minutes and 90 minutes. Twenty-four hours after exposure, cells were analyzed for percent cytotoxicity grown on the 24-well ALI insert (LDH assay). UFP exposure resulted in decreased cell viability (significantly increased LDH levels). The result shows that Acrylonitrile butadiene styrene (ABS) has the most significant particle emission. ALI exposures enable in vitro testing of mixtures of particles such as UFP from a 3D printer. ABS is the only filament with a significant difference compared with the HEPA control in 90 minutes of exposure (p-value &lt;0.05). ABS and PETG we used during the experiment presented a significant difference compared with the HEPA control in 45 minutes of exposure.A screening analysis of potential exposure to these products in a typical environment suggests caution should be used when operating many printer and filament combinations in poorly ventilated spaces or without the aid of combined gas and particle filtration systems.

As a dominant mangrove species, Kandelia obovata is distributed in an intertidal marsh with an active H₂S release. Whether H₂S participates in the salt tolerance of mangrove plant is still ambiguous although increasing evidence have demonstrated that H₂S functions in plant responses to multiple abiotic stresses. In this study, as an H₂S donor, NaHS was used to investigate the regulatory mechanism of H₂S on salt tolerance of K. obovata seedlings using a combined physiological and proteomic analysis. The results showed that the reduction in photosynthesis (Pn) caused by 400 mM NaCl was recovered by the addition of NaHS (200 μM). Furthermore, the application of H₂S enhanced the quantum efficiency of PSII and the membrane lipid stability, implying that H₂S is beneficial to the survival of K. obovata seedlings under high salinity. We further identified 37 differentially expressed proteins by proteomic approaches under salinity and NaHS treatment. Among them, the proteins related to photosynthesis, primary metabolism, stress response and hormone biosynthesis were primarily enriched. The physiological and proteomic results highlighted that exogenous H₂S up-regulated photosynthesis and energy metabolism to help K. obovata to cope with high salinity. Specifically, H₂S increased photosynthetic electron transfer, chlorophyll biosynthesis and carbon fixation in K. obovata leaves under salt stress. Furthermore, the abundances of other proteins related to metabolic pathway, such as antioxidation (APX, CSD2, PDX1), protein synthesis (HSP, Cpn 20), nitrogen metabolism (GS2, GS1:1), glycolysis (PGK, TPI), AsA-GSH cycle were increased by H₂S under high salinity. These findings provide new insights into the roles of H₂S in the adaptations of mangrove plant K. obovata to high salinity environment.

This article explores the relationship between Wang Yangming's philosophy and the new quality productivity, revealing how the new quality productivity, while inheriting the core ideas of Yangming's philosophy, achieves a higher level through innovation and development. The new quality productivity emphasizes the integration and innovation of knowledge, technology, and information, characterized by knowledge-driven innovation, information technology support, sustainable green development, and global collaborative development. The fusion of Yangming's philosophy and the new quality productivity holds significant theoretical and practical implications.

The assessment of water quality consists of counting bacteria indicating fecal contamination or detecting the presence of pathogenic bacteria using standardized or validated methods of classical microbiology. Our present study aims to determine the bacteriological quality of drilling water in the Tandjilé region of Chad. Our method used was based on qualitative and quantitative research on suspected total coliforms, Echerichia Coli and fecal enterococci were analyzed according to the standard routine methods of the French Association for Normalization (AFNOR). Microbiological analysis shows the presence of indicators of fecal contamination such as total coliforms, Escherichia coli and fecal enterococci. The number of strains detected in 100 ml were E. coli (7 /29 samples), fecal Streptococcus (6 /29 samples) and total coliforms (29/29 samples), respectively from borehole water. The contamination rate of E. coli is 24.13%, total coliforms 100% and 20.68% of fecal enterococci in boreholes. The high number of these microorganisms is more than the values recommended by the WHO for the quality of drinking water. Corrective and urgent measures are needed to improve the quality of these water resources, rich in pathogens, which are health risks, and the causes of infectious diseases such as gastroenteritis, diarrhea, typhoid and skin diseases.

Oil and petroleum are strategic resources of great importance to national security. Petroleum and hydrothermal gold deposits may form together, with similar evolutionary trends in their formation, migration, and enrichment. Petroleum reservoirs and gold deposits are closely coupled under certain geological conditions. The solubility of gold in crude oil and its forms of occurrence are important in determining the mechanisms of interaction between gold and petroleum and in facilitating the recovery of gold from gold-bearing petroleum. In this study, the occurrence of gold in crude oil from the Linnan Depression in the Bohai Bay Basin, China, was studied using inductively coupled plasma–mass spectrometry and X-ray photoelectron spectroscopy. Concentrations of gold in crude oil from the Linpan and Shanghe oilfields averaged 44.5 ppb, which is well above the minimum concentration required for hydrothermal gold mineralization. Gold has an affinity with carbon, oxygen, and sulfur, and its concentration in crude oil is positively correlated with total acid and sulfur contents. We speculate that gold may exist in crude oil as complexes with organic acids or thiols, with crude oil thus being a transport medium for gold.

Uncertain fractional differential equation (UFDE) is an excellent tool for describing complicated dynamic systems. This paper analyzes the valuation problems of currency option based on UFDE under optimistic value criterion. Firstly, an uncertain fractional currency model is formulated to describe the dynamics of foreign exchange rate. Then, the pricing formulae of European, American and Asian currency option are obtained under optimistic value criterion, respectively. Finally, numerical simulations are provided to illustrate the validity of our theoretical results.

In recent years, ozone (O3) pollution has been rapidly spreading, restricting further improvement of air quality in China. Investigating the interaction of O3 concentration and identifying their driven cities are important for the prevention and control of O3 pollution in China. However, the complex interaction between O3 pollution between the cities and their driven cities has not yet been revealed. In this study, we address this gap based on complex network methods. Specifically, an ozone relational network is constructed using an association calculation method. The driven nodes and spatial clusters were analyzed based on the maximum matching algorithm and the Louvain algorithm. The findings of the study reveal an aggregation phenomenon in the ozone network concerning distance. Furthermore, as the threshold Tc varies, the proportion of driven nodes exhibits a positive correlation. Moreover, a closer threshold value corresponds to a higher coincidence ratio of the driven nodes. The results provide scientific guidance for national O3 pollution prevention and regional synergy formatting. Furthermore, the introduced network-based approaches offer a mythological framework for the study of air pollution in key cities and clusters.

The COVID-19 pandemic introduced risks and challenges to global food and nutrition security. In this paper, we examine the impact of the COVID-19 pandemic on the nutritional intake of China's rural residents using panel data and a fixed effect model. The data were collected in 2019 and 2020 and covered nine provinces and 2,631 households in rural China. The results reveal that an increase of 100 confirmed cases in a county resulted in a 1.48% (p<0.01), 1.46% (p<0.01), 1.77% (p<0.01), and 1.23% (p<0.01) decrease in per capita intake of dietary energy, carbohydrates, fats, and proteins, respectively. Moreover, the COVID-19 pandemic only had a significant and negative effect on dietary energy intake in the low-income group at the 5% level of significance. Our study indicates that the potential insufficient nutrition situation, nutritional imbalance, and dietary imbalance of low-income rural residents should be addressed appropriately.

In response to the structural optimization problem of PCB stator coreless disc motors, the orthogonal response surface method was used to optimize the motor structure, determine the basic parameters of the motor preliminarily, and conduct orthogonal experiments on the motor parameters based on the optimization design objectives, The optimization factors were the quantity of magnetic pole of the motor rotor, the ratio of main/auxiliary pole size, the thicknessof the permanent magnet, and the air gap length.The motor torque，the amplitude of magnetic density of the air gap and waveform distortion rateare used as optimization objectives. The motor parameters that make the motor torque reach the maximum, the air gap magnetic density maximum, and the waveform distortion rate minimum. Due to the use of PCB plates instead of motor stator cores in PCB coreless disc motors,The service life of the PCB board during motor operation will be reduced with the temperature rise generated by the stator winding To solve this problem, the response surface analysis of the motor is carried out to reduce the temperature rise of the stator windings during the operation of the motor. PCB board and stator winding are the main factors affecting the temperature rise of the motor.Taking the thickness of the PCB board, the hole diameter on the board, and the uneven width of the stator winding as optimization factors, the motor parameters with the lowest temperature rise of the motor winding are obtained. Simulation analysis is conducted using Ansys/Maxwell software, and the results prove the feasibility of optimization.

Gross strap muscle invasion (gSMI) in patients with differentiated thyroid cancer (DTC) was defined as high-risk recurrent group in the 2015 American Thyroid Association guidelines. However, controversy persists because several studies suggested gSMI had little effect on disease outcome. Herein, a systematic review and meta-analysis was conducted to investigate impact of gSMI on outcome of DTC. Methods: A systematic search of electronic databases (PubMed, EMBASE, Cochrane Library, and MEDLINE) for studies published until February 2020 was performed. Case-control studies and randomized controlled trials that studied the impact of gSMI on outcome of DTC were included. Results: Six studies (all retrospective studies) involving 13639 patients met final inclusion criteria. Compared with no extrathyroidal extension (ETE), patients with gSMI were associated with increased risk of recurrence (P=0.0004,OR, 1.46; 95% CI: 1.18 to 1.80) and lymph node metastasis (LNM) (P<0.00001,OR 4.19;95% CI. 2.53 to 6.96). For mortality (P=0.34,OR 1.47;95% CI:0.67 to 3.25), ten-year disease-specific survival (P=0.80, OR 0.91;95% CI:0.44 to 1.88) and distant metastasis (DM) (P=0.21, OR 2.94;95% CI. 0.54 to 15.93), there was no significant difference between gSMI and no ETE group. In contrast with maximal ETE, patients with gSMI were associated with decreased risk of recurrence (P<0.0001,OR, 0.58; 95% CI: 0.44 to 0.76) , mortality (P=0.0003,OR 0.20;95% CI:0.08 to 0.48), LNM (P=0.0003,OR 0.64;95% CI. 0.50 to 0.81) and DM (P=0.0009,OR 0.28;95% CI. 0.13 to 0.59). Conclusions: DTC patients with gSMI had a higher risk of recurrence and LNM than those without ETE. However, in contrast with maximal ETE, a much better prognosis was observed in DTC patients with only gSMI. The findings of our meta-analysis provide supportive evidence for the validity of the T category changes in the 8th edition American Joint Committee on Cancer system. The actual impact of gSMI should be re-evaluated and revised in the recurrent risk stratification system in the future.

The surface velocity of the Amery Ice Shelf (AIS) is vital to assessing its stability and mass balance. Previous studies have shown that the AIS basin has a stable multi-year average surface velocity. However, spatiotemporal variations in the surface velocity of the AIS and the underlying physical mechanism remain poorly understood. This study combined offset tracking and DInSAR methods to extract the monthly average surface velocity of the AIS and obtained the inter-annual surface velocity from the ITS_LIVE product. An uneven spatial distribution in inter-annual variation of the surface velocity was observed between 2000–2022, although the magnitude of variation was small at less than 20.5 m/yr. The increase and decrease in surface velocity on the eastern and western-central sides of the AIS, respectively, could be attributed to the change in the thickness of the AIS. There was clear seasonal variation in monthly average surface velocity at the eastern side of the AIS between 2017–2021, which could be attributed to variations in the area and thickness of fast-ice and also to variations in ocean temperature. This study suggested that changes in fast-ice and ocean temperature are the main factors driving spatiotemporal variation in the surface velocity of the AIS.

In order to better understand the source-sink flow and relationships of Zinc (Zn) and other nutrients in wheat (Triticum aestivum L.) plants for biofortification and improving grain nutritional quality, effects of reducing photoassimilate source (through the flag leaf removal and spike shading) or sink (through 50% spikelets removal) in the field on accumulation of Zn and other nutrients in wheat grains of two cultivars (Jimai 22 and Jimai 44) were investigated under two soil Zn application levels. The single panicle weight (SPW), kernel number per spike (KNPS), thousand kernel weight (TKW), total grain weight (TGW), concentrations and yields of various nutrient elements (Zn, Fe, Mn, Cu, N, P, K, Ca and Mg), phytate phosphorus (phytate-P), phytic acid (PA) and phytohormones (ABA: abscisic acid, and the ethylene precursor ACC: 1-aminocylopropane-1-carboxylic acid), and C/N ratios were determined. Soil Zn application significantly increased concentrations of grain Zn, N and K. Cultivars showing higher grain yields had lower grain protein and micronutrient nutritional quality. SPW, KNPS, TKW (with an exception of TKW in half spikelets removal), TGW, and nutrient yields in wheat grains were most severely reduced by half spiklets removal, secondly by spike shading, and slightly by flag leaf removal. Grain concentrations of Zn, N and Mg consistently showed negative correlations with SPW, KNPS and TGW, but positively with TKW. There were general positive correlations among grain concentrations of Zn, Fe, Mn, Cu, N and Mg, and bioavailability of Zn and Fe (estimated by molar ratios of PA/Zn, PA × Ca/Zn, PA/Fe, or PA × Ca/Fe). Although concentrations of Zn and Fe were increased and Ca was decreased in treatments of half spikelets removal and spike shading, the simultaneously increased PA limited the increase in bioavailability of Zn and Fe. In general, different nutrient elements interact with each other and are affected to different degrees by source-sink manipulations. Elevated endogenous ABA levels and ABA/ACC ratios were associated with increased TKW and grain-filling of Zn, Mn, Ca and Mg, and inhibited K in wheat grains. However, effects of ACC were diametrically opposite. These results provide basis for wheat grain biofortification to alleviate human malnutrition.

Transient receptor potential melastatin-8 (TRPM8) is a cation channel that is activated by cold and “cooling agents” such as menthol and icilin, which induce a cold sensation. Stimulation of TRPM8 activates an intracellular signaling cascade that ultimately leads to a change in the gene expression pattern of the cells. Here, we investigated the TRPM8-induced signaling pathway that links TRPM8 channel activation to gene transcription. Using a pharmacological approach, we show that inhibition of phosphatidylinositol 4-phosphate 5 kinase alpha (PIP5K), an enzyme essential for the biosynthesis of phosphatidylinositol 4,5-bisphosphate, attenuated TRPM8-induced gene transcription. Analyzing the link between TRPM8 and Gq proteins, we show that pharmacological inhibition of the beta gamma subunits impairs TRPM8 signaling. In addition, genetic studies showed that TRPM8 requires an activated Galpha subunit for signaling. In the nucleus, the TRPM8-induced signaling cascade triggers an activation of the transcription factor AP-1, a complex consisting of a dimer of basic region leucine zipper (bZIP) transcription factors. Here, we identified the bZIP protein c-Jun as an essential component of AP-1 within the TRPM8-induced signling cscade. In summary, with PIP5K, Gq subunits and c-Jun we have identified key molecules in the TRPM8-induced signaling from the plasma membrane to the nucleus.

Penile squamous cell carcinoma (SCC) is a rare disease. Treatment options for advanced penile cancer are often limited and prognosis remains poor. We reported a 52-year-old male recurrent and metastatic penile SCC patient with high PD-L1 expression(90%) and TMB(14.4 muts/Mb). He had undergone penectomy, bilateral inguinal lymph node dissection and excision of the abdominal wall mass during two surgeries. Despite cisplatin-based concurrent chemoradiotherapy and sequential chemotherapy with docetaxel plus cisplatin were then carried out, the carcinoma still had progressed. The patient then obtained progression free survival exceeding 32 months with continuous sintilimab, although new onset of ICI-induced diabetes after 24 cycles of sintilimab and required sustained insulin treatment. He didn’t have positive type 1 diabetes associated autoantibodies, but had susceptible HLA genotype DR3-DQ2 haplotype. This is the first patient with radiation and multichemorefractory penile SCC obtained remarkable anti-tumor effect of partial regression exceeding 32 months during continuous sintilimab.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

Mesoporous TiO2/reduced graphene oxide/Ag (TiO2/RGO/Ag) ternary nanocomposite with effective electrons transfer pathway is obtained by an electrostatic self-assembly method and photo-assisted treatment. Compared with bare mesoporous TiO2 (MT) and mesoporous TiO2/RGO (MTG), the ternary mesoporous TiO2/RGO/Ag (MTGA) nanocomposite exhibited superior photocatalytic performance for the degradation of MB under visible light, and the degradation rate reached 0.017 min-1, which was 3.4 times higher than that of MTG. It is proposed that Ag nanoparticles can form the local surface plasmon resonance (LSPR) to absorb the visible light and distract the electrons into MT, and RGO can accept the electrons from MT to accelerate the separation efficiency of carriers. The establishment of MTGA ternary nanocomposite make the three components act synergistic effect to enhance the photocatalytic performance.

Codon use bias is an important characteristic in the process of genetic information transmission of species. With the publication of the genome of C. panzhihuaensis, it is of great significance to investigate the codon use bias for understanding the genetic evolution of this species and for molecular breeding. In this study, Perl language and CodonW 1.4.2 software was used to systematically analyze the coding gene sequences of the C. panzhihuaensis genome, obtain the characteristics of codon use, and identify the sources of variation affecting codon use. The results showed that GC3s content, GCall content, and ENC value were 46.75%, 47.67%, and 52.8 respectively. As the first seed plant, the GC3 content of Cycas is similar to that of most gymnosperms and most dicotyledons, but considerably different from that of monocotyledons.RSCU value was greater than 1, among which 21 codons ended in U or A. Enc-plot analysis, PR2-plot neutral plot analysis, and correlation coefficient analysis of Axis1 with GC3s and CAI revealed that the codon bias was mainly affected by natural selection, but also by mutation pressure and other factors. Thirty-one optimal codons of Cycas genes were screened. This research can provide a reference for the phylogeny and genome codon evolution of Cycas.

K417G Ni-based superalloy is widely used in aeroengine turbine blade for its excellent properties. However, the aeroengine rotor blade zigzag crown appears early failure frequently, which is because of the wear problems occurring in the working process. Laser forming repairing (LFR) is a promising technique to repair these damaged blades. Unfortunately, the laser formed Ni-based superalloys with high content of (Al + Ti) have a high cracking sensitivity. In this paper, the crack characterization of the LFRed K417G, the microstructure, microhardness and tribological properties of the coating before and after laser remelting are presented. The results show that the microstructure of as-deposited K417G consists of γ phase, γ′ precipitated phase, γ + γ′ eutectic and carbide. Cracking mechanisms including solidification cracking, liquation cracking and ductility dip cracking are proposed based on the composition of K417G and processing characteristics to explain the cracking behavior of the K417G superalloy during LFR. After laser remelting, the microstructure of the coating has been refined, and the microhardness and tribological properties has been improved. Laser remelting can decrease the size of the cracks in the LFRed K417G but not the number. Therefore, laser remelting can be applied as an effective method for strengthening coating and as an auxiliary method for controlling cracking.

Medium-deep Borehole Heat exchanger (MBHE) has been widely paid attention for building heating. In order to avoid the thermal interference of adjacent MBHEs, temperature distribution characteristics of medium-deep rock-soil was investigated in this work. The evolution on maximum rock-soil thermal affected radius (MTAR) in full life cycle was further analyzed. The results showed that the rock-soil thermal affected area (RTAA) continuously expands in both radial and vertical directions during a heating season. Several factors of thermal extraction load, fluid velocity, geothermal gradient and pipe length have main impacts on the RTAA in vertical direction. Rock-soil thermal conductivity affects the RTAA in both radial and vertical directions. In non-heating season, temperature difference of rock-soil in radial direction dominates the temperature recovery in the first year while geothermal flow nearly dominates temperature recovery after 20 years. The thermal affected radius (TAR) in the 30 th year could be determined as an effective MTAR in full life cycle. In order to decrease installed distance of adjacent MBHEs, a new well layout form by deflecting borehole was proposed. The recommended deflection angle is equal to or larger than 4 times TAR angle. This work provides scientific reference for promoting application of multiple MBHE arrays.

Benign design of alkali-activated slag/FA geopolymer paste has intriguing increasing attention for optimizing its service performance. Therefore, the replacement of fly ash (FA) with 10 wt% silica fume (SF) is investigated by mechanical strength after freeze-thawing cycles and microstructure characterization. The results show that an appropriate dosage (30 wt%) of slag is necessary to attain alkali-activated slag/FA geopolymer paste with excellent mechanical performance, and the SF/slag/FA (SF: slag: FA= 10:30:60, wt%) geopolymer paste exerts the compressive and flexural strength of 95.2 and 3.2 MPa, respectively. Meanwhile, the doped 10 wt% SF facilitates the propagation of (N, C)-A–S–H chains, rather than the formation of C-S-H gels, evidenced by the absent exothermic peak at about 861oC from the differential scanning calorimetry (DSC) curves, leading to the increases in the pores volume with a pore diameter<20 nm and tortuosity by mercury intrusion porosimeter (MIP) results, corresponding to an improved freezing-thawing resistance with the residual compressive strength of 52.8 MPa and the weight loss of 10.5% after 300 freeze-thawing cycles. It explores a cost-effective and benign facile approach to designing heating curing-free alkali-activated slag/FA geopolymer paste with good freezing-thawing resistance.

Recycling of metallurgical solid waste has intriguing increasing attention for fabricating cementitious materials, due to its low-carbon emission, cost-effectiveness, and environmental conservation. Herein, the effects of silica fume (SF) on the microstructure and mechanical properties of alkali-activated slag/FA (fly ash) pastes subjected to elevated temperatures (150, 500, 850, and 1200℃) are investigated, to clarify the fact that whether or not the SF generates positive roles in mechanical properties of slag/FA geopolymers. The results show that the replacement with 10 wt% SF (silica fume) promotes the increasing pore volume with a diameter of 0.2~3 μm at room temperature, leading to an increase in the compressive or flexural strength, “right shifts” of endothermic peak and the initial-final temperature of mass loss, presenting a denser and compact fracture surface. Meanwhile, the mineral phase of gehlenite and labradorite emerges after exposure above 850℃ from the XRD results. Furthermore, the bloating effect of the incorporated SF occurs due to the formation of a liquid phase altogether with the amorphous silicates after exposure to 1200℃, leading to a greater deformation and enhancement of restructuring involved in the [SiO4]4− and [AlO4]5−. It explores an effective recycling approach for fabricating paste binders using metallurgical solid wastes.

Precision and accuracy estimation is an important index used to reflect the measurement performance and quality of a measurement system. To reveal the significance and connotations of the precision and accuracy estimation index of a close-range photogrammetry system, several common precision and accuracy estimation methods used in close-range photogrammetry are explained from a theoretical perspective, and the mechanism of the internal coincidence precision estimation and the external coincidence accuracy estimation are deduced, respectively. Through detailed experimental design and testing, the validity and reliability of the proposed precision and accuracy estimation methods are verified, which provides strong evidence for the quality control, optimisation, and evaluation of the measurement results from a close-range photogrammetry system. At the same time, it has significance for the further development of precision and accuracy estimation analysis of close-range photogrammetry systems.

Stabilization of a G-quadruplex (G4) in the promotor of the c-MYC proto-oncogene leads to inhibition of gene expression, and it thus represents a potentially attractive new strategy for cancer treatment. However, most G4 stabilizers show little selectivity among the many G4s present in the cellular complement of DNA and RNA. Intriguingly, a crescent-shaped cell-penetrating thiazole peptide, TH3, preferentially stabilizes the c-MYC G4 over other promotor G4s, but the mechanisms leading to this selective binding remain obscure. To investigate these mechanisms at the atomic level, we performed an in silico comparative investigation of the binding of TH3 and its analogue TH1 to the G4s from the promotors of c-MYC, c-KIT1, c-KIT2, and BCL2. Molecular docking and molecular dynamics simulations, combined with in-depth analyses of non-covalent interactions and bulk and per-nucleotide binding free energies, revealed that both TH3 and TH1 can induce the formation of a sandwich-like framework through stacking with both the top and bottom G-tetrads of the c-MYC G4 and the adjacent terminal capping nucleotides. This framework produces enhanced binding affinities for the c-MYC G4 relative to other promotor G4s, with TH3 exhibiting an outstanding binding priority. Van der Waals interactions were identified to be the key factor in complex formation in all cases. Collectively, our findings fully agree with available experimental data. Therefore, the identified mechanisms leading to specific binding of TH3 towards the c-MYC G4 provide valuable information to guide the development of new selective G4 stabilizers.

Brucella abortus is a facultative intracellular Gram-negative bacterium that causes chronic persistent infections in humans and livestock. In this study, conventional bio-typing, multiple-locus variable-number tandem repeat analysis (MLVA), and whole-genome sequencing-single-nucleotide polymorphism (WGS-SNP) were used to investigate the molecular epidemiology characteristics of Brucella abortus strains in China and their relationships to world lineages. A total of 100 strains were collected from 1953 to 2013, suggesting that B. abortus circulated in China in the past five decades. Moreover, most strains were mainly distributed in the northwest area. During this period, seven biovars were found, indicating that B. abortus displayed a high diversity of biovars and that the main epidemic areas are in the northern provinces. Strains have high genetic diversity, and bruce07 is the most helpful locus for genotyping of this population. Moreover, 17 MLVA-11 genotypes were found; 13 of them are of known genotypes and four are unassigned genotypes, indicating that B. abortus in this study had several geographic origins. Still, strains from unassigned genotypes may originate from China. Many shared MLVA-16 genotypes were observed in strains from the same provinces in Northern China, which confirmed a brucellosis outbreak within northern regions. WGS-SNP analysis showed that eight Chinese strains formed a ladder-like phylogram (C. Ⅶ) with strains from nine countries, including Uganda, Iraq, Russia, Georgia, Spain, Italy, Egypt, Mongolia, and China; strains were introduced to these countries from a single source. Notably, Chinese strains were closely related to strains from Russia and Mongolia; frequent animal (cattle) trade and exchanges may promote this process. We will provide new and insightful information for strength surveillance and control of B. abortus brucellosis in China.

Using the data of China's A-share non-financial listed enterprises from 2015 to 2022 as a sample, this study empirically tests the impact of ESG rating disagreement on corporate debt financing cost. The results show that ESG rating disagreement significantly increases the debt financing costs of enterprises, and this result still holds after a series of robustness tests such as replacing the dependent and independent variables and PSM approach. Meanwhile, the heterogeneity analysis reveals that non-state-owned enterprises and enterprises in non-heavily polluting industries are more sensitive to ESG ratings disagreement. In addition, mechanism analysis shows that corporate financing constraints mediate the relationship between ESG rating disagreements and debt financing costs. The findings of this study provide important evidence for understanding the impact of ESG rating disagreement on the costs of debt financing, enrich the meaning of ESG rating disagreement, and reveal the significance of unifying ESG rating standards.

The combination of wet-lab experimental data on multi-site combinatorial mutations and machine learning is an innovative method in protein engineering. In this study, we present an improved innovative sequence–activity relationship (innov'SAR) methodology based on novel descriptors and digital signal processing (DSP) to construct a predictive model. In this improved approach, 21 experimental (R)-selective amine transaminases from Aspergillus terreus (AT-ATA) were used as an input to predict higher thermostability than that predicted using the existing data. We successfully improved the determination coefficient (R2) of the model from 0.66 to 0.92. In addition, root mean square deviation (RMSD) and root mean square fluctuation (RMSF) were estimated and conformation analysis based on molecular dynamics simulations was performed to verify the enhanced thermal stability of the screened mutants. The improved innov'SAR algorithm enhanced the predictive accuracy, suggesting a method for modifying the stability of AT-ATA, which may help in directed evolutionary screening and open up new avenues for protein engineering.

This study aims to explore the effect of real-time visual feedback (VF) information of the pres-sure of center (COP) provided by intelligent insoles on balance training in a one leg stance (OLS) and tandem stance (TS) posture. Thirty healthy female college students were randomly assigned to the visual feedback balance training group (VFT), non-visual feedback balance training group (NVFT), and control group (CG). The balance training includes: OLS, tandem Stance (dominant leg behind, TSDL), tandem stance (non-dominant leg behind, TSNDL). The training lasted 4 weeks, the training lasts 30 minutes at an interval of 1 days. There was a sig-nificant difference in the interaction effect between Groups*Times of the COP parameters (p<0.05) for OLS. There was no significant difference in the interaction effect between Groups*Times of the COP parameters (p>0.05) for TS. The main effect of the COP parameters was a significant difference in Times (p<0.05). The COP displacement, velocity, radius, and area in VFT significantly decreased after training (p < 0.05). Therefore, the visual feedback technology of intelligent auxiliary equipment during balance training can enhance the benefit of training. The use of smart wearable devices in OLS balance training may improve the visual and physical balance integration ability.

Atherosclerosis (AS) is a chronic progressive disease caused by various factors, and causes various cerebrovascular and cardiovascular diseases (CVDs). Reducing the plasma levels of low-density lipoprotein-cholesterol (LDL-C) is the primary goal in preventing and treating AS. Proprotein Convertase Subtilisin/Kexin Type 9 (PCSK9) plays a crucial role in regulating LDL-C metabolism. Panax notoginseng has potent lipid-reducing effects and protects against CVDs, and its saponins induce vascular dilatation, inhibit thrombus formation, and are used in treating CVDs. However, the anti-AS effect of the secondary metabolite, 20(S) -protopanaxatriol (20(S)-PPT), remains unclear. In this study, the anti-AS effect and molecular mechanism of 20(S)-PPT were investigated in vivo and in vitro by western blotting, real time-polymerase chain reaction (RT-PCR), Enzyme-linked Immunosorbent Assay (ELISA), immunofluorescence staining, and other assays. The in vitro experiments revealed that 20(S)-PPT reduced the levels of PCSK9 in the supernatant of HepG2 cells, upregulated low density lipoprotein receptor (LDLR) protein levels, promoted LDL uptake by HepG2 cells, and reduced PCSK9 mRNA transcription by upregulating the levels of FoxO3 protein and mRNA and decreasing the levels of HNF1α protein and mRNA. The in vivo experiments revealed that 20(S)-PPT upregulated aortic αSMA expression, increased the stability of atherosclerotic plaques, and reduced aortic plaque formation induced by a high-cholesterol fed in ApoE-/- mice (HCF group). Additionally, 20(S)-PPT reduced the aortic expression of CD68, reduced inflammation in the aortic root, and alleviated the hepatic lesions in the HCF group. The study revealed that 20(S)-PPT inhibited LDLR degradation via PCSK9 to alleviate AS.

Physical inactivity is a well-known risk factor for various non-communicable diseases (NCDs). Sufficient physical activity (PA) is essential for the prevention of NCDs and thus it is imperative to study the current status of PA and its influencing factors among rural residents in China. A population-based survey was conducted in rural areas of Shandong, Shanxi and Yunnan Provinces using a stratified random sampling method. The International Physical Activity Questionnaire Short Form (IPAQ-S) was used to collect the data on PA. A total of 3780 rural residents participated in the survey. The result showed that 22.2% of rural residents were physical inactivity. The proportion of rural residents reporting practice of physical exercise was 54.4%. The most frequently performed physical exercise was walking/brisk walking(78.3%).Binary logistic regression analyses showed that being female, people at age between 15 to 34 years or 60 years old and above, employees of governmental departments/retirees, school students, the unemployed, people with NCDs were risk factors of PA and ethnic minority groups,smoking and alcohol consumption were risk factors of physical exercise. Health promotion programme aiming at increasing people’s PA in rural China is needed and it should focus on the populations groups of the female, people at age 60 years and above ,school students, the unemployed, and people with NCDs.

Managing severe bleeding, particularly in soft tissues and visceral injuries, remains a significant challenge in trauma and surgical care. Traditional hemostatic methods often fall short in wet and dynamic environments. This study addresses the critical issue of severe bleeding in soft tissues, proposing an innovative solution using a Polyethylene Glycol (PEG)-based hydrogel combined with zinc oxide (ZnO). The developed hydrogel forms a dual-network structure through amide bonds and metal ion chelation, resulting in enhanced mechanical properties and adhesion strength. The hydrogel, exhibiting excellent biocompatibility, is designed to release zinc ions, promoting coagulation and accelerating hemostasis. Comprehensive characterization, including gelation time, rheological properties, microstructure analysis, and swelling behavior, demon-strates the superior performance of the PEG/ZnO hydrogel compared to traditional PEG hydro-gels. Mechanical tests confirm increased compression strength and adhesive properties, crucial for withstanding tissue dynamics. In vitro assessments reveal excellent biocompatibility and en-hanced procoagulant ability attributed to ZnO. Moreover, in vivo experiments using rat liver and tail bleeding models demonstrate the remarkable hemostatic performance of the PEG/ZnO hy-drogel, showcasing its potential for acute bleeding treatment in both visceral and peripheral sce-narios.

Osteoporosis (OP), a prevalent skeletal disorder characterized by compromised bone strength and increased susceptibility to fractures, poses a significant public health concern. This review aims to provide a comprehensive analysis of the current state of research in the field, focusing on the application of proteomic techniques to elucidate diagnostic markers and therapeutic targets for OP. The integration of cutting-edge proteomic technologies has enabled the identification and quantification of proteins associated with bone metabolism, leading to a deeper understanding of the molecular mechanisms underlying OP. In this review, we systematically examine recent advancements in proteomic studies related to OP, emphasizing the identification of potential biomarkers for OP diagnosis and the discovery of novel therapeutic targets. Additionally, we discuss the challenges and future directions in the field, highlighting the potential impact of proteomic research in transforming the landscape of OP diagnosis and treatment.

The Pythagorean fuzzy set (PFS), which is characterized by a membership and a non-membership degree and the square sum of them is less or equal to one, can act as an effective tool to express decision makers’ fuzziness and uncertainty. Considering that the Heronian mean (HM) is a powerful aggregation operator which can take the interrelationship between any two arguments, we study the HM in Pythagorean fuzzy environment and propose new operators for aggregating interval-valued Pythagorean fuzzy information. First, we investigate the HM and geometric HM (GHM) under interval-valued intuitionistic fuzzy environment and develop a series of aggregation operators for interval-valued intuitionistic fuzzy numbers (IVIFNs) including interval-valued intuitionistic fuzzy Heronian mean (IVIFHM), interval-valued intuitionistic fuzzy geometric Heronian mean (IVIFGHM), interval-valued intuitionistic fuzzy weighted Heronian mean (IVIFWHM) and interval-valued intuitionistic fuzzy weighted geometric Heronian mean (IVIFWGHM). Second, some desirable and important properties of these aggregation operators are discussed. Third, based on these aggregation operators, a novel approach to multi-attribute decision making (MADM) is proposed. Finally, to demonstrate the validity of the approach, a numerical example is provided and discussed. Moreover, we discuss several real-world applications of these operators within policy-making contexts.

The human serotonin transporter (hSERT) terminates neurotransmission by removing serotonin from the synaptic cleft, which is an essential process plays an important role in depression. In addition to substrate serotonin, hSERT is also the target of drugs of abuse like cocaine and clinically used antidepressants such as escitalopram and paroxetine. To date, few studies attempt to investigate the unbinding mechanism underlying the orthosteric and allosteric modulation of hSERT. The high-resolution X-ray structure of hSERT resolved recently enables us to theoretically study the unbinding of the above four ligands against the S1 or S2 site of hSERT, by means of molecular docking, molecular dynamics (MD) and potential of mean force (PMF) simulations. We proved that for either the S1 or S2 site, the other three ligands (cocaine, escitalopram and paroxetine) are much more favorable than the original substrate serotonin, whether in kinetics along the unbinding pathways or in thermodynamics at the equilibrium states. Furthermore, the S1 site is much more favorable than the S2 site, for each ligand. Interestingly, inspection revealed that there are ~ 3Å lengths between the allosteric site of serotonin and cocaine, and an unseen un-binding pathway for escitalopram at the S1 site except for verification of the broadest trail.

Retinitis pigmentosa (RP) clinically and genetically heterogeneous group of inherited retinal disorders (IRD) that result in retinal degeneration. This study aimed to identify the genetic findings of patients with autosomal recessive retinitis pigmentosa (arRP). Whole exome sequencing (WES) was performed in two unrelated Pakistani families underlying arRP. Data analysis and mutation screening was performed for all the known RP genes following bi-directional Sanger sequencing to determine whether any of the candidate variants co-segregated with the disease phenotype in the families. WES data analysis revealed a novel homozygous missense variant (c.1274T>C) in the in Tubby like Protein 1 (TULP1 NM_003322.6) gene in family 1 and a novel homozygous frameshift variant (c.351delC) in the retinoid isomerohydrolase 65 (RPE65 NM_000329.3) gene in family 2. The identified variants perfectly co-segregated with the disease phenotype within the families. Our results strongly suggest that mutations in TULP1 and RPE65 are responsible for the retinal phenotype in the affected individuals. These mutations will increase the mutation spectrum of these genes; furthermore, it will enhance our knowledge and understanding of the underlying molecular mechanisms of retinitis pigmentosa.

Abstract- Cognitive radio (CR) play an important role in improving spectral efficiency (SE) of wireless communication, meanwhile, intelligent reflecting surface (IRS) is an effective technology to improve the secrecy performance of wireless communication system by adjusting the phase shift and amplitude of channel. Thus, we consider an IRS-aided multiple-input single-output (MISO) CR systems to enhance secrecy rate, which is consists of a single eavesdropping link, a primary network containing the primary receiver (PR), and secondary network including secondary receiver (SR) and the SR transmitter (SR-TX). Specifically, we minimize the transmit power of SR subject to secrecy capacity constraint and interference temperature (IT) constraint on PR, by jointly optimizing the beamforming vector and artificial noise (AN) constraints matrix at SR-TX as well as the phase shift matrix of IRS. Numerical results show that the different values of transmit antennas at the SR-TX and the number of IRS elements can significantly decrease the transmit power under the condition of ensuring secure communication.

Light trapping in single nanowires (NWs) are of vital importance for photovoltaic applications. However, circular NWs (CNWs) can limit its light-trapping ability due to high geometrical symmetry. In this work, we present a detailed study of light trapping in single NWs with an elliptical cross-section (ENWs). We demonstrate that the ENWs exhibit significantly enhanced light trapping compared with the CNWs, which can be ascribed to the symmetry-broken structure that can orthogonalize the direction of light illumination and the leaky mode resonances (LMRs). That is, the elliptical cross-section can simultaneously increase the light path length by increasing the vertical axis and reshape the LMR modes by decreasing the horizontal axis. We found that the light absorption can be engineered via tuning the horizontal and vertical axes, the photocurrent is significantly enhanced by 374.0% (150.3%, 74.1%) or 146.1% (61.0%, 35.3%) in comparison with that of the CNWs with the same diameter as the horizontal axis of 100 (200, 400) nm or the vertical axis of 1000 nm, respectively. This work advances our understanding of how to improve light trapping based on the symmetry breaking from the CNWs to ENWs and provides a rational way for designing high-efficiency single or self-assembled NW photovoltaic devices.

Establishing an accurate mathematical model is the foundation of simulating the motion of marine vehicles and structures, and it is the basis of modeling-based control design. System identification from observed input-output data is a practical and powerful method. However, for modeling objects with different characteristics and known information, a single modeling framework can hardly meet the requirements of model establishment. Moreover, there are some challenges in system identification, such as parameter drift and overfitting. In this work, three robust methods are proposed for generating ocean hydrodynamic models based on Bayesian regression. Two Bayesian techniques, semi-conjugate linear regression and noisy input Gaussian process regression, are used for parametric and nonparametric gray-box modeling and black-box modeling. The experimental free-running tests of the KVLCC2 ship model and a multi-freedom wave energy converter (WEC) are used to validate the proposed Bayesian models. The results demonstrate that the proposed schemes for system identification of the ship and WEC have good generalization ability and robustness. Finally, the developed modeling methods are evaluated considering the aspects required conditions, operating characteristics and prediction accuracy.

Today’s intruders usually send attacking commands to a target system through several stepping-stone hosts, in order to reduce the chance of being detected. With stepping-stone intrusion (SSI), the intruder’s identity is hidden behind a long interactive chain of hosts and very hard to detect. An effective approach for SSI detection (SSID) is to estimate the length of the chain. This type of method is called network-based SSID. Most existing network-based SSID worked effectively only when intruders’ session manipulation was not present. These known SSID algorithms are either weak to resist intruders’ chaff-perturbation manipulation or having very limited capability in resisting attacker’s session manipulation. This paper develops a novel network-based SSID algorithm resistant to intruders’ chaff-perturbation by using packet crossover. Our proposed SSID algorithm is simple and easy to implement as the number of packet crossovers can be easily computed. We conduct rigorous technical proofs to verify the correctness of our proposed algorithm. The experimental results show that our proposed SSID algorithm works effectively and perfectly in resisting intruders’ chaff-perturbation up to 50% chaff rate.

Background: Lung cancer (LC) is a major leading cause of death worldwide. Immunomodulators that target several immune mechanisms have proven to reduce tumor burden in experimental models through induction of the immune microenvironment. We hypothesized that other biological mechanisms may also favor tumor burden reduction in lung cancer-bearing mice treated with immunomodulators. Methods: Tumor weight, area, and immune cells (T, B, macrophages, and TNF-alpha levels, immunohistochemistry) and tumor growth, oxidative stress, apoptosis, autophagy, and sirtuin-1 markers were analyzed (immunoblotting) in subcutaneous tumor of BALB/c mice injected with LP07 adenocarcinoma cells treated with monoclonal antibodies (CD-137, CTLA-4, PD-1, and CD-19, N=9/group) and non-treated control animals. Results: Compared to non-treated cancer mice, in tumors of monoclonal-treated animals, tumor area and weight and ki-67 significantly reduced, while T cell counts, oxidative stress, apoptosis, autophagy, and sirtuin-1 marker increased. Conclusion: Immunomodulators elicited a reduction in tumor burden (reduced tumor size and weight) through decreased tumor proliferation and increased oxidative stress, apoptosis, autophagy, and sirtuin-1 levels, which may have interfered with the immune profile of the tumor microenvironment. Future research should be devoted to the elucidation of the specific contribution of each biological mechanism to the reduced tumor burden.

Knee Osteoarthritis (KOA) is a chronic disease characterized by progressive disability and joint pain. Meniscus chondrocytes apoptosis is the main cause of reduced chondrocyte number and self-repair function. The purpose of this study was to investigate the role of miR-27b-3p in KOA.In this study, we found that the expression of miR-27b-3p was downregulated in cultured IL-1β treated chondrocyte and cartilage tissues in KOA. KOA overexpression evidently reduced IL-1β induced chondrocyte apoptosis and caspase-3 and caspase-9 expression.The upregulated iNOS and COX-2 mRNA and proteins expression was also inhibited by miR-27b-3p mimics. The expression of nitric oxide, PGE2, TNF-α and IL-6 was also inhibited by miR-27b-3p mimics. The target gene of miR-27b-3p was confirmed to be BDNF. TrkB/CREB pathway was proved to be the downstream pathway of miR-27b-3p/BDNF axis.The apoptotic cell percentage and nitric oxide, PGE2, TNF-α and IL-6 expression was induced by BDNF+IL-1β. This induction was inhibited by miR-27b-3p mimics. The cartilage tissues stained with safranin O results showed miR-27b-3p greatly decreased KOA induced cartilage degradation. The expression of BDNF、TrkB and p-CREB was inhibited by len-miR-27b-3p. MiR-27b-3p also reduced the expression of TNF-α、IL-6 and Bax, and increased Bcl-2 expression. These results indicated miR-27b-3p could applied to inhibit the development of KOA and miR-27b-3p/BDNF/TrkB/CREB pathway could serve as novel treatment target to handle KOA.

Tungsten and its alloys are considered as a key component in high temperature environment. Self-passivating W-Si-xY alloys with different Y contents made from the powders milled for different times were prepared by mechanical alloying (MA) and spark plasma sintering (SPS). Their microstructures and oxidation resistance were investigated. It is found that the oxidation resistance of the alloys with low Y contents (0Y and 2Y) made from 20 h-milled powders is worse than that of the alloys made from 4 h-milled powders. It is because the protective WO3/SiO2 composite layer is discontinuous. While the alloys with high Y contents (4Y and 6Y) made from 4 h and 20 h-milled powders show good oxidation resistance. Even, the thickness of the oxide layer of the alloys with 4Y and 6Y made from 20 h-milled powders after oxidation at 1000 ℃ for 2 h is 84.0 μm and 70.7 μm, less than that made from 4 h-milled powders. This is due to the size and distribution of W5Si3, Y2Si2O7 aggregates and W-Y-O melt. The synergistic effects of Y contents and milling time on the microstructures and oxidation resistance of the alloys are revealed.

The requirements for using noncyanide imitation gold plating as decorative electroplating are increasing; thus, continuously improving the quality of the coating of the imitation gold plating and optimizing the coating process have become the current priority. In this work, hydroxyethylidene diphosphonic acid (HEDP) was used as the main complexing agent, CuSO4·5H2O, ZnSO4·7H2O and NaSnO3·3H2O were the main salts, and NaOH and anhydrous sodium carbonate were used as the buffers to prepare the electroplating solution. Using sodium citrate (SC), sodium potassium tartrate (SS), sodium gluconate (SG), and glycerol (Gl) as four additives, the effects of the number of carboxyl groups on the properties of a Cu-Zn-Sn alloy coating were compared. The electrochemical analysis showed that Cu-Zn-Sn alloy codeposition occurred at -0.50 V vs. Hg|HgO. The scanning electron microscopy (SEM) results showed that the particle size of the coatings obtained with carboxyl-containing additives was more uniform than that obtained with the electroplating solution without additives. The X-ray fluorescence spectrometry (XRF) analysis revealed that the composition of the Cu-Zn-Sn alloy coating obtained by using SC as an additive in the electroplating solution was 89.75 wt% Cu, 9.61 wt% Zn, and 0.64 wt% Sn, and the color of the coating was golden yellow. The X-ray diffraction (XRD) pattern showed that the coating was a mixture of Cu, Cu5Zn8, CuSn, Cu6Sn5, and CuZn phases. The analysis of the electroplating solution by UV, IR and NMR spectroscopy methods indicates that the additives improve the coating by affecting the complexation reaction of metal ions. These results can provide technical and theoretical guidance for developing Cu-Zn-Sn ternary alloy electrodeposition technology with the new cyanide-free HEDP alkaline electroplating system.

The study of the currently known >3,000 species of snakes can provide valuable insights into the evolution of their genomes. Deinagkistrodon acutus, also known as Sharp-nosed Pit Viper, one hundred-pacer viper or five-pacer viper, is a venomous snake with significant economic, medicinal and scientific importance. Widely distributed in southeastern China and South-East Asia, D. acutus has been primarily studied for its venom. Here, we employed next-generation sequencing to assemble and annotate a highly continuous genome of D. acutus. The genome size is 1.46 Gb; its scaffold N50 length is 6.21 Mb, the repeat content is 42.81%, and 24,402 functional genes were annotated. This study helps to further understand and utilize D. acutus and its venom at the genetic level.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

[Objective] To investigate the expression of ALDH2 in hepatocellular carcinoma and its correlation with macrophage infiltration and with the activation of specific subtypes of macrophages. [Methods] Transcriptome and clinical data from patients with hepatocellular carcinoma were downloaded from The Cancer Genome Atlas (TCGA) and the International Cancer Genome Consortium (ICGC) databases and analyzed and collated using R and Perl software. In the TCGA hepatocellular carcinoma dataset, the Wilcoxon test was used to identify macrophage activation-related gene sets that show differential expression between hepatocellular carcinoma and normal tissues. Single-cell sequencing combined with bulk data was used to analyze macrophage infiltration of hepatocellular carcinoma immune cells and the activation and recruitment of different subtypes of macrophages. Single-factor Cox regression and minimum absolute convergence and selection operator (Lasso) were used to identify survival-related genes and construct prognostic models of HCC. The patients were divided into two groups based on their model scores. The Wilcoxon test was used to identify differentially expressed genes (DEGs) between the two groups, and gene ontology (GO) and Kyoto Encyclopedia of Genes and Genomes (KEGG) functional enrichment analyses of the DEGs were performed. Single-sample gene set enrichment analysis (ssGSEA) was performed to explore the possible mechanism underlying the differences in prognosis. The reliability of the model was verified using the ICGC hepatocellular carcinoma dataset. A Kaplan‒Meier curve was constructed and used to analyze the influence of macrophage activation-related gene expression on survival and prognosis in patients with hepatocellular carcinoma. The log-rank test and the independent t test were used to analyze survival time data and to compare immune cell infiltration in the two groups. [Results] In a comparison of hepatocellular carcinoma and paracancerous tissues, the expression of six of 137 macrophage activation-related genes (ALDH2, CCNB2, CYP2C9, CYP3A4, F9 and KLKB1) was found to be significantly correlated with overall survival time (OS) in patients with hepatocellular carcinoma. Based on this finding, a prognosis assessment model for hepatocellular carcinoma was constructed. The OS of the patients in the high-scoring group was significantly shorter than the OS of the patients in the low-scoring group (P<0.05), and the model predicted the prognosis of patients with hepatocellular carcinoma independently of sex, age, tumor grade and stage. The area under the receiver operating characteristic (ROC) curve of the model used to predict 1-, 2-, and 3-year survival was greater than 0.7 in both the test set and the validation set. GO enrichment of DEGs between the high- and low-scoring groups of the model suggested that the DEGs are mainly related to immune function. GSEA suggested that the tumor-infiltrating immune cells in the high-scoring group were macrophages, Th2 cells and Treg cells and showed that the number of tumor-infiltrating immune cells, including NK cells, was lower in the high-scoring group than in the low-scoring group. With respect to immune function, the immune checkpoint of the high-scoring group was higher than that of the low-scoring group. Single-cell sequencing data indicated the recruitment of B cells, M0 cells, M1 cells and M2 cells to the hepatocellular carcinoma microenvironment and suggested that ALDH2 regulates related signaling pathways in a way that promotes the differentiation of macrophages into M2-type macrophages. [Conclusion] M2-type macrophages are the dominant type of macrophages associated with immune infiltration in hepatocellular carcinoma. The macrophage-associated activation gene ALDH2 activates the macrophage polarization signaling pathway and negatively regulates the differentiation of macrophages into M2-type macrophages.

Drought poses a significant constraint on rice production, and in this study, we have discovered a novel drought-sensitive mutant, designated as dsm3, arising from the progenies of indica rice variety Zhonghui8015 treated with EMS. Under drought stress conditions, dsm3 exhibited characteristic withered leaf tips, accompanied by increased levels of MDA and H2O2, reduced Pn, and decreased activity of POD and SOD. Genetic analysis revealed that the withered leaf tip phenotype was governed by a single recessive gene, designated as Osdsm3.To begin with, Osdsm3 was initially mapped to the short arm of chromosome 1 through a cross involving dsm3 and 02428. Subsequently, utilizing a population of 2591 F2 individuals, we narrowed down the location of Osdsm3 to a 78Kb interval, encompassing 13 open reading frames (ORFs). Sequencing analysis unveiled a mutation (1275G→A) in the exon of the candidate gene (LOC_Os01g10680), leading to premature translation termination. Moreover, a quantitative RT-PCR assay demonstrated high expression of OsDSM3 in the panicle and sheath, with a significant upregulation of drought stress-related genes under drought conditions. Phylogenetic analyses indicated that Osdsm3 shares evolutionary homology with UNE1, an intracellular transport protein found in Arabidopsis thaliana. Subcellular studies further confirmed that OsDSM3 resides in the cytoplasm. In conclusion, the forthcoming cloning of Osdsm3 holds promise for delving deeper into the molecular mechanisms governing rice drought resistance.

Hydrogel antibacterial agent is an ideal antibacterial material because of it could diffuses antibacterial molecules into the decayed area by providing a suitable microenvironment and the hydrogel acts as a protective barrier on the decay interface. The biocompatibility and biodegradation make the removal process easily which were widely used in medical fields. However, there have been few reports on its application for controlling postharvest diseases in fruit. In this study, the Chitosan-Ag (CS-Ag) complex hydrogels were prepared using the physical crosslinking method, which used for controlling postharvest diseases in grape. The prepared hydrogels were stable for a long period at room temperature. The structure and surface morphology of CS-Ag composite hydrogels were characterized by UV-Vis, FTIR, SEM, and XRD. The inhibitory effects of CS-Ag hydrogel on disease in grape caused by P. expansum, A. niger and B. cinerea were investigated both in vivo and in vitro. The remarkable antibacterial activity of CS-Ag hydrogels was mainly due to the synergistic antibacterial and antioxidant effects of CS and Ag. Preservation test showed that the CS-Ag hydrogel had positive fresh-keeping effect. This revealed CS-Ag hydrogels plays a critical role in controlling fungal disease in grape.

Side-scan sonar (SSS) detection is a key method in applications such as underwater environmental security and subsea resource development. The use of acoustic images for seabed target detection has gradually become a mainstream underwater detection method. However, many existing detection approaches primarily concentrate on tracking the evolution path of optical image object detection tasks, resulting in complex structures and limited versatility. To tackle this issue, we introduce a pioneering Dual-Domain Multi-Frequency Network (D2MFNet) meticulously crafted to harness the distinct characteristics of SSS image detection. In D2MFNet, aiming at the underwater detection requirements of small scenes, we introduce a novel method for optimize and improve the detection sensitivity of different frequency ranges and propose a Multi-Frequency Combined Attention Mechanism (MFCAM). This mechanism amplifies the relevance of dual-domain features across different channels and space. Moreover, recognizing that SSS images can provide richer insights after frequency domain conversion, we introduce a Dual-Domain Feature Pyramid Network (D2FPN). By incorporating frequency domain information representation, D2FPN significantly augments the depth and breadth of feature information in underwater small datasets. Our methods are seamlessly designed for integration into existing networks, offering plug-and-play functionality with substantial performance enhancements. We have conducted extensive experiments to validate the efficacy of our proposed techniques, and the results showcase their state-of-the-art performance. MFCAM improves the mAP by 16.9% in the KLSG dataset and 15.5% in the SCTD dataset. The mAP of D2FPN was improved by 8.4% in the KLSG dataset and by 9.8% in the SCTD dataset. We will make our code and models publicly available at https://dagshub.com/estrellaww00/D2MFNet.

Obesity results in hepatic fat accumulation, i.e., steatosis. Besides the fat overload, impaired fatty acid β-oxidation also promotes steatosis. Fatty acid β-oxidation takes place in mitochondria and peroxisomes. Usually very long chain and branched-chain fatty acids are first oxidized in peroxisomes, and the resultant short chain fatty acids are further oxidized in mitochondria. Peroxisome biogenesis is regulated by peroxin 16 (PEX16). In liver-specific PEX16 knockout (Pex16Alb-Cre) mice, hepatocyte peroxisomes were absent, but hepatocytes proliferated, and liver mass was enlarged. These results suggest that normal liver peroxisomes restrain hepatocyte proliferation and liver sizes. After high fat diet (HFD) feeding, body weights were increased in PEX16 floxed (Pex16fl/fl) mice and adipose-specific PEX16 knockout (Pex16AdipoQ-Cre) mice but not in the Pex16Alb-Cre mice, suggesting that the development of obesity is regulated by liver PEX16 but not by adipose PEX16. However, it was previously reported that HFD-induced obesity in the Pex16AdipoQ-Cre mice was more severe than in the wild type mice, which was not observed until 27 weeks of HFD feeding. Thus, liver initiates the development of obesity, which is enhanced by abnormal adipocytes. HFD increased liver mass in the Pex16fl/fl mice but somehow reduced the already enlarged liver mass in the Pex16Alb-Cre mice. Basal levels of serum triglyceride, free fatty acids and cholesterol were decreased whereas serum bile acids were increased in the Pex16Alb-Cre mice, and HFD-induced steatosis was not observed in the Pex16Alb-Cre mice. These results suggest that normal liver peroxisomes contribute to the development of liver steatosis and obesity.

Streptomyces sp. HNS054, which was previously isolated from a marine sponge, demonstrates vigorous growth and facile genetic modification. This study explores its potential as a marine ac-tinomycete chassis through complete genome sequencing and genetic engineering. With a 7.5 Mb genome containing 6678 predicted genes, 21 secondary metabolic biosynthetic gene clusters (BGCs), and 8 common site-specific recombination (SSR) system attB loci, HNS054 shows a close phylogenetic relation to S. griseoincarnatus strain RB7AG. Utilizing multiplexed site-specific ge-nome engineering (MSGE) and the CRISPR/Cas9 method, engineered strains derived from HNS054 (with three copies of the target BGCs) produce higher amounts of aborycin and ac-tinorhodin than S. coelicolor M1346 (containing three copies of the same BGCs). HNS054 stands out for its remarkable characteristics, including salt tolerance, rapid growth, and compatibility with synthetic biology tools, and positions it as a promising candidate for developing marine ac-tinomycete hosts to enhance secondary metabolite production.

The impact of the agriculture net carbon effect is crucial for climate change mitigation, yet research on this topic in China is currently insufficient. In this study, the carbon balance ratio (CBR) is used to characterise the net carbon effect of agriculture, and the spatial Durbin model and threshold regression model were used to empirically analyse the CBR with a sample of 30 provincial-level regions in China from 2004 to 2019. The aim was to investigate the mechanism of the influence of the land management scale (SCALE) of farming on the CBR. The results of the study indicate that national farming generally has a net sink effect, with large changes in interannual fluctuations; the expansion of SCALE has an obvious role in increasing sinks and reducing emissions, and has a positive spatial spillover effect on CBR, with significant spatial heterogeneity. Furthermore, as the SCALE expands, the direction of the influence of rural residents’ income and education level on CBR changes in the opposite direction, showing a significant non-linear relationship characteristic. However, in most areas, the SCALE threshold has not yet been reached, suggesting that the improvement in education levels can still offset the negative impact of economic income growth in the short term. The study recommends paying attention to the role of farmers’ human capital, changing production methods, and implementing carbon peaking and carbon neutrality goals to enhance the net sink effect of the farming industry, which would be achieved by increasing land management scale.