In this paper, different concepts of reconfigurable RF-MEMS attenuators for beamforming applications are proposed and critically assessed. Capitalizing on the previous part of this work, the 1-bit attenuation modules featuring series and shunt resistors and low-voltage membranes (7-9 V) are employed to develop a 3-bit attenuator for fine-tuning attenuations (&lt; -10 dB) in the 24.25-27.5 GHz range. More substantial attenuation levels are investigated by means of fabricated samples of coplanar waveguide (CPW) sections equipped with Pi-shaped resistors aiming at attenuations of -15, -30, and -45 dB. The remarkable electrical features of such configurations, showing flat attenuation curves and limited return losses, and the investigation of a switched-line attenuator design based on them led to the final proposed concept of a low-voltage 24-state attenuator. Such simulated device combines the Pi-shaped resistors for substantial attenuations with the 3-bit design for fine-tuning operations, showing a maximum attenuation level of nearly -50 dB while maintaining steadily flat attenuation levels and limited return losses (< -11 dB) along the frequency band of interest.

This paper describes different variants of broadband and simple attenuator modules for beamforming applications, based on Radio Frequency Micro Electro-Mechanical Systems (RF-MEMS), framed within Coplanar Waveguide (CPW) structures. The modules proposed in the first part of this work differ in their actuation voltage, topology, and desired attenuation level. Fabricated samples of basic 1-bit attenuation modules, characterized by a moderate footprint of 690 x 1960 µm2 and aiming at attenuation levels of -2, -3 and -5 dB in the 24.25-27.5 GHz range, are presented in their variants featuring both low actuation voltages (5-7 V) as well as higher values (~ 45V), the latter ones ensuring larger mechanical restoring force (and robustness against stiction). Beyond the fabrication non-idealities that affected the described samples, the substantial agreement between simulations and measurement outcomes proved that the proposed designs could provide precise attenuation levels up to 40 GHz, ranging up to nearly -3 dB and -5 dB for the series and shunt variants, respectively. Moreover, they could be effective building blocks for future wideband and reconfigurable RF-MEMS attenuators. In fact, in the second part of this work, combinations of the discussed cells and other configurations meant for larger attenuation levels will be investigated.

This study aimed to identify whether gyrate atrophy of the choroid and retina (GACR) heterozygous individuals have possible clinical manifestations and to explore the potential pathogenic mechanism. In this retrospective study, we surveyed a two-generation pedigree of an individual diagnosed with GACR. Two family members underwent ophthalmological, hematologic, and genetic tests. An arginine-restricted diet with vitamin B6 supplementation was implemented; clinical assessments were repeated every 3 months during follow-up. Relative OAT mRNA expression was determined using real-time quantitative polymerase chain reaction. The 19-year-old compound heterozygous daughter (OAT: c.1186C&gt;T; c.748C&gt;T), had bilateral high myopia, posterior staphyloma, chorioretinal atrophy, macular abnormalities, and elevated hematologic ornithine. The 54-year-old heterozygous mother (OAT: c.1186C&gt;T), presented with bilateral severe myopia, asymmetric posterior staphyloma, retina and choroidal capillary layer atrophy, retinal pigment epithelium abnormalities, and mildly elevated hematologic ornithine. Compared to normal individuals, the daughter and mother had 29% and 46% relative OAT mRNA expression, respectively (P&lt;0.001). We believe that this is the first report of a carrier of one OAT variant allele with mild phenotypes, suggesting that family members should be aware of the possible involvement of autosomal recessive conditions. Additional data suggests nonsense mediated decay-initiated mRNA degradation may cause GACR.

This paper presents a system for identification of wind features, such as gusts and wind shear. These are of particular interest in the context of energy-efficient navigation of Small Unmanned Aerial Systems (UAS). The proposed system generates real-time wind vector estimates and a novel algorithm to generate wind field predictions. Estimations are based on the integration of an off-the-shelf navigation system and airspeed readings in a so-called direct approach. Wind predictions use atmospheric models to characterize the wind field with different statistical analyses. During the prediction stage, the system is able to incorporate, in a big-data approach, wind measurements from previous flights in order to enhance the approximations. Wind estimates are classified and fitted into a Weibull probability density function. A Genetic Algorithm (GA) is utilized to determine the shaping and scale parameters of the distribution, which are employed to determine the most probable wind speed at a certain position. The system uses this information to characterize a wind shear or a discrete gust and also utilizes a Gaussian Process regression to characterize continuous gusts. The knowledge of the wind features is crucial for computing energy-efficient trajectories with low cost and payload. Therefore, the system provides a solution that does not require any additional sensors. The system architecture presents a modular decentralized approach, in which the main parts of the system are separated in modules and the exchange of information is managed by a communication handler to enhance upgradeability and maintainability. Validation is done providing preliminary results of both simulations and Software-In-The-Loop testing. Telemetry data collected from real flights, performed in the Seville Metropolitan Area in Andalusia (Spain), was used for testing. Results show that wind estimation and predictions can be calculated at 1 Hz and a wind map can be updated at 0.4 Hz. Predictions show a convergence time with a 95% confidence interval of approximately 30 s.

In this paper, we aim to present real implementation cases where non-visible elements of environmental impact assessments (EIA), wind flow, are visualized using a 3D digital twin technology. The conventional EIA process serves as a crucial tool in the evaluation of potential environmental impacts prior to the initiation of development projects. This evaluation helps to establish a legal and institutional framework that seeks to minimize the adverse effects on the environment. However, traditional EIA methods present challenges, particularly for non-experts, in comprehending the results of assessments involving non-visible environmental factors such as noise, air quality, and wind flow. These elements are often represented in static images or numerical tables, limiting accurate understanding and engagement. Our proposed method, termed Digital Twin based EIA, addresses these limitations by leveraging digital twin technology. This advanced methodology allows for the visualization of non-visible environmental elements in a spatio-temporal dimension, providing a more interactive and comprehensive user interface/experience for both citizens and stakeholders. In this context, we present a unique case study that focuses on visualizing wind flow using this technology. This paper serves as an example of how digital twin platforms can enhance traditional EIA processes, offering a more immersive and informative experience. The evolution of EIA into the digital realm signifies an important step forward in fostering public understanding and engagement in environmental protection efforts.

As the most serious of the many worse new pathological changes caused by diabetes, there are many risk factors for the occurrence and development of DR. It mainly includes hyperglycemia, hypertension, hyperlipidemia and so on. Among them, hyperglycemia is the most critical cause, which plays a key role in the pathological changes of DR.High-sucrose diets(HSDs) lead to elevated blood glucose levels in vivo, which, through oxidative stress, inflammation, the production of AGEs and VEGF, causes plenty of pathological damages to the retina and ultimately bring about loss of vision. The existing therapies for DR primarily target the terminal stage of the disease, when irreversible visual impairment has appeared. Therefore, early prevention is particularly critical. Early prevention of DR-related vision loss requires adjustments to dietary habits, mainly by reducing sugar intake. This article primarily discusses the risk factors, pathophysiological processes, and molecular mechanisms associated with the development of DR caused by HSDs. It aims to raise awareness of the crucial role of diet in the occurrence and progression of DR, promote timely changes in dietary habits, prevent vision loss, and improve the quality of life. The aim is to make people aware of the importance of diet in the occurrence and progression of DR. According to the dietary modification strategies we give, patients can change their poor eating habits timely, avoid the retinopathy that can be avoided theoretically, and obtain a excellent outcome.

To accurately determine the refractive error of the eye, sufficient relaxation of eye accommodation is essential, either through the fogging technique or pharmacological cycloplegia. This study aimed to evaluate the clinical information revealed after cycloplegia and assess how age and non-cycloplegic refractive status influence the classification of eye refractive error. We analyzed the records of 472 non-population-based subjects aged 3–28 years (mean ± SD: 9.1 ± 4.6) who attended a private ophthalmology practice from January 2018 to December 2020. Cycloplegia was induced with one drop of cyclopentolate 1% in each eye, and refraction was measured 30 ± 5 min later using an objective autorefractometer. The average spherical equivalent (SE) difference (mean ± SD) induced by cycloplegia was 0.72 ± 0.73 D, with the highest difference observed in the 3-5 years age group (1.18 ± 0.85 D). Gender had no significant effect on the SE values before or after cycloplegia (p &gt; 0.05). Cycloplegia caused a hyperopic refractive shift in 83% of participants, no shift in 12%, and a myopic refractive shift in 6%. This study highlights the importance of cycloplegia use in children and young adults.

Diseases in articular cartilages have affected millions of people globally. Although the biochemical and cellular composition of articular cartilages is relatively simple, there is the limitation in self-repair ability of cartilage. Therefore, developing the strategies for cartilage repair is very important. Here, we reported a new manufacturing process of water-based polyurethane based photosensitive materials with hyaluronic acid and applied the materials for 3D printed customized cartilage scaffolds. The scaffold has high cytocompatibility and is one that closely mimics the mechanical properties of articular cartilages. It is suitable for culturing human Wharton's jelly mesenchymal stem cells (hWJMSCs) and the cells showed an excellent chondrogenic differentiation capacity. We consider that the 3D printing hybrid scaffolds may have potential in customized tissue engineering and facilitate the development of cartilage tissue engineering.

Most of the existing calibration methods for binocular stereo vision sensor (BSVS) depend on high-accuracy target with feature points that are difficult to manufacture and costly. In complex light conditions, optical filters are used for BSVS, but they affect imaging quality. Hence, the use of a high-accuracy target with certain-sized feature points for calibration is not feasible under such complex conditions. To solve these problems, a calibration method based on unknown-sized elliptical stripe images is proposed. With known intrinsic parameters, the proposed method adopts the elliptical stripes located on the parallel planes as a medium to calibrate BSVS online. In comparison with the common calibration methods, the proposed method avoids utilizing high-accuracy target with certain-sized feature points. Therefore, the proposed method is not only easy to implement but is a realistic method for the calibration of BSVS with optical filter. Changing the size of elliptical curves projected on the target solves the difficulty of applying the proposed method in different fields of view and distances. Simulative and physical experiments are conducted to validate the efficiency of the proposed method. When the field of view is approximately 400 mm × 300 mm, the proposed method can reach a calibration accuracy of 0.03 mm, which is comparable with that of Zhang’s method.

A human eye has about 120 million rod cells and 6 million cone cells. This huge number of light sensing cells inside a human eye will continuously produce a huge quantity of visual signals which flow into a human brain for daily processing. However, the real-time processing of these visual signals does not cause any fatigue to a human brain. This fact tells us the truth which is to say that human-like vision processes do not rely on complicated formulas to compute depth, displacement, and colors, etc. On the other hand, a human eye is like a PTZ camera. Here, PTZ stands for pan, tilt and zoom. We all know that in computer vision, each set of PTZ parameters (i.e., coefficients of pan, tilt and zoom) requires a dedicated calibration to determine a camera’s projection matrix. Since there is an infinite number of PTZ parameters which could be produced by a human eye, it is unlikely that a human brain stores an infinite number of calibration matrices for each human eye. Therefore, it is an interesting question for us to answer, which is to say whether simpler formulas of computing depth and displacement exist or not. Moreover, these formulas must be calibration friendly (i.e., easy process on the fly or on the go). In this paper, we disclose an important discovery of a new solution to 3D projection in a human-like binocular vision system. The purpose of doing 3D projection in binocular vision is to undertake forward and inverse transformations (or mappings) between coordinates in 2D digital images and coordinates in a 3D analogue scene. The formulas underlying the new solution are accurate, easily computable, easily tunable (i.e., to be calibrated on the fly or on the go) and could be easily implemented by a neural system (i.e., a network of neurons). Experimental results have validated the discovered formulas.

Background: Visual acuity (VA) assessments are crucial in ophthalmology but traditionally rely on in-clinic evaluations. The emergence of telemedicine has spurred interest in creating dependable self-administered VA tests for use beyond standard clinical environments. This study evaluates the practicality and validity of a self-administered Near VA card test against traditional Snellen and Rosenbaum Pocket Vision Screener (RPVS) methods for home monitoring and enhancing clinical workflow. Methods: In a cross-sectional study a near VA card (Hadassah Self-Visual Acuity Screener-HSVA) was developed with written and videotaped instructions for self-use. Patients with a minimal best corrected VA (BCVA) of 1.0 LogMAR in at least one eye were recruited from Ophthalmology and Optometry clinics. Outcomes included mean BCVA difference between the self-administered and those obtained by the examiner, and correlations among BCVA values obtained by Snellen, RPVS, HSVA and previous distance BCVA according to the patient electronic medical records. Results: A total of 275 participants (mean age: 42.5±19.4 years, range: 18-89 years, 47% female) were included. Test-retest reliability analysis for the HSVA demonstrated very good correlation and repeatability (n=38 patients.; Rs=1.0, P

The research aims to present an innovative methodology to execute the Heritage conservation processes in a collaborative and interdisciplinary BIM project, with an effective management of the deterioration suffered over time, emphasizing the structures and coatings. The research begins with the architectural survey using scanning techniques (TLS) and terrestrial photogrammetry (SfM) and taking as a study the Duomo of Molfetta (Italy), a unique Romanesque architecture of Puglia (Italy). The methodological process is mainly aided by the precise semantic segmentation of global point clouds, a semi-automatic process assisted by classification algorithms implemented in the post-processing software, and which has allowed the classification of the unstructured information provided by the remote sensing equipment when identifying the architectural-structural systems of a building with high historical values. Subsequently, it has been possible to develop an efficient Scan-to-HBIM workflow, where the Heritage-BIM (HBIM) project has fulfilled the function of a database by incorporating and organizing all the information (graphic and non-graphic) to optimize the tasks of auscultation, identification, classification, quantification and, in turn, facilitating the parametric modeling of unique structures and architectural elements. The results have shown great effectiveness in the processes of characterization of architectural and artistic heritage, focusing on the deformations and deterioration of the masonry in columns, and making multidisciplinary conservation work in an HBIM project more flexible. But there are still some difficulties for the automatic interpretation of 3D point cloud data, related to specific systems of the historical architecture. In conclusion, human action and interpretation continues to be a fundamental pillar to achieve precise results in a heritage environment.

Purpose of research was to determine changes in optical quality for monthly disposable soft contact lenses (SCL) wearers with new and monthly worn SCL. Retinal straylight was assessed in SCL wearers using a C-Quant straylight meter. The study included 33 participants (age 22 ± 1.4 years) who wore monthly disposable silicone hydrogel contact lenses. Measurements were taken with month-old SCL that had been worn for no more than 4 hours. Participants then replaced the old lenses with new ones. After a 15-minute adaptation period, straylight measurements were taken with the new SCL. A questionnaire was administered to all participants, inquiring about vision complaints and the type of contact lens material used. The decimal logarithm of the stray-light parameter, log(s), was notably higher with month-old SCL (log(s) = 0.97±0.17) than with brand-new SCL (log(s) = 0.86±0.15), p < 0.001. The average increase in retinal straylight after a month of SCL use was log(s) = 0.11 ± 0.08. The questionnaire revealed that 35% of participants observed a reduction in visual quality after wearing the contact lenses for a month. Results showed that monthly disposable soft contact lenses could reduce visual quality when scheduled replacement time has been reached.

Dams are a critical infrastructure system for many communities, but they are also one of the most challenging to inspect. Dams are typically very large and complex structures, and the result is that inspections are often time-intensive and require expensive, specialized equipment and training to provide inspectors with comprehensive access to the structure. The scale and nature of dam inspections also introduces additional safety risks to the inspectors. Unmanned aerial vehicles (UAV) have the potential to address many of these challenges, particularly when used as a data acquisition platform for photogrammetric three-dimensional (3D) reconstruction and analysis, though the nature of both UAV and modern photogrammetric methods necessitates careful planning and coordination for integration. This paper presents a case study on one such integration at the Brighton Dam, a large-scale concrete gravity dam in Maryland, USA. A combination of multiple UAV platforms and multi-scale photogrammetry was used to create two comprehensive and high-resolution 3D point clouds of the dam and surrounding environment at intervals. These models were then assessed for their overall quality, as well as their ability to resolve flaws and defects that were artificially applied to the structure between inspection intervals. The results indicate that the integrated process is capable of generating models that accurately render a variety of defect types with sub-millimeter accuracy. Recommendations for mission planning and imaging specifications are provided as well.

Integrating optical coherence tomography (OCT) into the pre-surgical stage of cataract management holds significant clinical and economic potential, particularly in low-to-middle-income countries like Kazakhstan. This study aimed to evaluate these impacts by prospectively recruiting 124 patients, aged 70±8 years, from two ophthalmology surgical centers in Almaty, Kazakhstan. Patients undergoing phacoemulsification of cataracts with monofocal intraocular lens (IOL) implantation between January and December 2022 were divided into two groups: the OCT group (n=75) received pre-operative OCT, while the Control group (n=49) did not. Visual acuity (VA) was measured pre- and post-surgery, and the cost-effectiveness of the surgical strategies was analyzed. The OCT group experienced a significantly greater improvement in VA (-0.647±0.232 logMAR) compared to the Control group (-0.543±0.244 logMAR), with a notable interaction between time and group (F(df) = 217.2, p &lt; 0.001). Additionally, pre-existing concomitant diseases were diagnosed in 25.3% of cases in the OCT group and 28.6% in the Control group. The economic analysis revealed that the integration of OCT facilitated multiple surgeries in one appointment, thereby reducing overall costs. These findings suggest that implementing OCT in the pre-surgical stage of cataract management can significantly enhance visual outcomes and decrease the cost of ophthalmology services in Kazakhstan.

In this work, we introduce the first pipeline that combines a refraction-aware Structure-from-Motion (SfM) method with a deep learning model specifically designed for airborne bathymetry. We accurately estimate the 3D positions of the submerged points by integrating refraction geometry within the SfM optimization problem. This way, no refraction correction as post-processing is required. Experiments with simulated data that approach the real-world capturing conditions demonstrate that SfM with refraction correction is extremely accurate, with submillimeter errors. We integrate our refraction-aware SfM within a deep learning framework that also takes into account radiometrical information, developing a combined spectral and geometry-based approach, with further improvements on accuracy and robustness to different seafloor types, both textured and textureless. We conducted experiments with real-world data at 2 locations in the southern Mediterranean Sea, with varying seafloor types which demonstrate the benefits of refraction correction for the deep learning framework. We open-source our refraction-aware SfM, providing researchers in airborne bathymetry with a practical tool to apply SfM in shallow water areas.

Solid state sensors having timing capabilities are becoming an absolute need in particle tracking techniques of future experiments at colliders. In this sense, silicon sensors having 3D structure are becoming an interesting solution, due to their intrinsic speed and radiation resistance. A characteristics of such devices is the strict dependence of their performance on their geometric structure, which can be widely optimised by design, thus requiring suitable tools for an accurate modeling of their behaviour. This paper illustrates the development, performance and use of the TCoDe simulator, specifically dedicated to the fast simulation of carrier transportation phenomena in solid state sensors. Some examples of its effectiveness in the design and analysis of 3D sensors is also given.

In the current paper, we present our work towards developing a solution combining computer vision and AI to support footrest design customization in the wheelchair industry. Wheelchairs and postural systems are complex and often user centric in the design process. Those products require a wide range of adjustments to adapt to the various anthropometries and disabilities of patients. Most commercial products, dedicated to severe disability, also include a series of additional elements, designed to keep the patient in a comfortable but “fixed” position. Such systems do not allow to “fix and maintain” the position of patient foot, especially for patients who have no control over their lower limbs. For that reason, it becomes essential to supply wheelchairs with specific elements to hold patient's shoe in place. Commercial foot supports are typically developed on standard sizes and do not always cover the entire population. In addition, those designs are based on standard shoes, thus they do not lend themselves well to adapting to special shoes or orthopedic shoes. Feet final position therefore becomes a key element in correct postural management. In this paper, we investigate the use of computer vision and AI to correctly define customization parameters of the footrest. The proposed design has been developed based on the specifications received from the Pro Medicare S.r.l orthopedic technicians. We present suitable algorithms, design principles and well defined components towards the implementation of our proof of concept. We also present the testing activities we have undertaken and the obtained performance results.

Manual visual inspections typically conducted after an earthquake are high-risk, subjective, and time-consuming. Delays from inspections often exacerbate the social and economic impact of the disaster on affected communities. Rapid and autonomous inspection using images acquired from unmanned aerial vehicles offer the potential to reduce such delays. Indeed, a vast amount of re-search has been conducted toward developing automated vision-based methods to assess the health of infrastructure at the component and structure level. Most proposed methods typically rely on images of the damaged structure, but seldom consider how the images were acquired. To achieve autonomous inspections, methods must be evaluated in a comprehensive end-to-end manner, incorporating both data acquisition and data processing. In this paper, we leverage recent advances in computer generated imagery (CGI) to construct a 3D synthetic environment for simulation of post-earthquake inspections that allows for comprehensive evaluation and valida-tion of autonomous inspection strategies. A critical issue is how to simulate and subsequently render the damage in the structure after an earthquake. To this end, a high-fidelity nonlinear finite element model is incorporated in the synthetic environment to provide a representation of earthquake-induced damage; this finite element model, combined with photo-realistic rendering of the damage, is termed herein a physics-based graphics models (PBGM). The 3D synthetic en-vironment with PBGMs provide a comprehensive end-to-end approach for development and validation of autonomous post-earthquake strategies using UAVs, including: (i) simulation of path planning of virtual UAVs and image capture under different environmental conditions; (ii) au-tomatic labeling of captured images, potentially providing an infinite amount of data for training deep neural networks; (iii) availability of the ground truth damage state from the results of the finite-element simulation; and (iv) direct comparison of different approaches to autonomous as-sessments. Moreover, the synthetic data generated has the potential to be used to augment field datasets. To demonstrate the efficacy of PBGMs, models of reinforced concrete moment-frame buildings with masonry infill walls are examined. The 3D synthetic environment employing PBGMs is shown to provide an effective testbed for development and validation of autonomous vision-based post-earthquake inspections that can serve as an important building block for ad-vancing autonomous data to decision frameworks.

Light pen 3D vision coordinate measurement systems are increasingly widely used due to their advantages, such as small size, convenient carrying and wide applicability. The posture of the light pen is an important factor affecting accuracy. The pose domain of the pen needs to be given so that the measurement system has a suitable measurement range to obtain more qualified parameters. The advantage of the self-calibration method is that the entire self-calibration process can be completed at the measurement site without any auxiliary equipment. After the system camera calibration is completed, we take several pictures of the same measurement point with different poses to obtain the conversion matrix of the picture, and then use spherical fitting, the generalized inverse method of least squares, and the principle of position invariance within the pose domain range. The combined stylus tip center self-calibration method calculates the actual position of the light pen probe. The experimental results show that the absolute error is stable below 0.0737 mm and that the relative error is stable below 0.0025 mm. The experimental results verify the effectiveness of the method; the measurement accuracy of the system can meet the basic industrial measurement requirements.

The COVID-19 pandemic has highlighted the need for a robust medical infrastructure and crisis management strategy as part of smart-city applications, with technology playing a crucial role. The Internet of Things (IoT) has emerged as a promising solution, leveraging sensor arrays, wireless communication networks, and artificial intelligence (AI)-driven decision-making. Advancements in Edge Computing (EC), Deep Learning (DL), and Deep Transfer Learning (DTL) have made IoT more effective in healthcare and pandemic-resilient infrastructure. When combined with medically oriented IoT setups, DL-architectures are suitable for integrating into pandemic-compliant medical infrastructure. The development of intelligent pandemic-compliant infrastructure requires combining IoT, edge and cloud computing, image processing, and AI tools to monitor adherence to social distancing norms, mask-wearing protocols, and contact tracing. The proliferation of 5G wireless communication has enabled ultra-wide broadband wireless communication, with high reliability and low latency, thereby enabling seamless medical support as part of smart-city applications. Such set-ups are designed to be ever-ready to deal with virus-triggered pandemic-like medical emergencies. This study presents the design of a pandemic-compliant mechanism leveraging IoT optimized for healthcare applications, edge- and cloud-computing frameworks, and a suite of DL-tools. The framework uses a composite attention-driven framework incorporating various DL-pre-trained models (DPTM) for protocol adherence and contact tracing. When connected to public networks, it can detect specific cyber-attacks. The results confirm the effectiveness of the proposed methodologies.

This paper presents a novel approach to designing beam codebooks for downlink multiuser hybrid multiple input multiple output (MIMO) wireless communication systems, leveraging multi-agent reinforcement learning (MARL). The primary objective is to develop an environment-specific beam codebook composed of non-interfering beams, learned by cooperative agents within the MARL framework. Machine learning (ML) based beam codebook design for downlink communications have been based on channel state information (CSI) feedback or only reference signal received power (RSRP) consisting of an offline training and user clustering phase. In massive MIMO, the full CSI feedback data is of large size and is resource-intensive to process, making it challenging to implement efficiently. RSRP alone for a stand-alone base station is not a good marker of the position of a receiver. Hence, in this work, uplink CSI estimated at the base station along with feedback of RSRP and binary acknowledgment of the accuracy of received data is utilized to design the beamforming codebook at the base station. Simulations using sub-array antenna and ray-tracing channel demonstrate the proposed system’s ability to learn topography-aware beam codebook for arbitrary beams serving multiple user groups simultaneously. The proposed method extends beyond mono-lobe and fixed beam architectures by dynamically adapting arbitrary shaped beams to avoid inter-beam interference, enhancing overall system performance. This work leverages MARL’s potential in creating efficient beam codebooks for hybrid MIMO systems, paving the way for enhanced multiuser communication in future wireless networks.

The reasons for the circular sense of human color perception generated by two sorts of color opponent neurons and three cone types are not well understood. Here we use geometrical analysis to examine the hypothesis that opponency, the recursive nature of color perception, and trichromacy arise as the most efficient ways of distinguishing spectrally different points on a plane using a minimum of color classes and receptor types.

Thermal infrared imagery provides temperature information on target objects, and has been widely applied in non-destructive testing. However, thermal infrared imagery is not always able to display detailed textures of inspected objects, which hampers the understanding of geometric entities consisting of temperature information. Although some commercial software has been developed for 3D thermal model displays, the software requires the use of expensive specific thermal infrared sensors. This study proposes a cost-effective method for 3D thermal model reconstruction based on image-based modeling. Two smart phones and a low-cost thermal infrared camera are employed to acquire visible images and thermal images, respectively, that are fused for 3D thermal model reconstruction. The experiment results demonstrate that the proposed method is able to effectively reconstruct a 3D thermal model which extremely approximates its corresponding entity. The total computation time for the 3D thermal model reconstruction is intensive while generating dense points required for the creation of a geometric entity. Future work will improve the efficiency of the proposed method in order to expand its potential applications to in-time monitoring.

We propose an approach for estimating the error in depth data provided by generic 3D sensors, which are modern devices capable of generating an image (RGB data) and a depth map (distance) or other similar 2.5D structure (e.g. stereo disparity) of the scene. Our approach starts capturing images of a checkerboard pattern devised for the method. Then proceed with the construction of a dense depth map using functions that generally comes with the device SDK (based on disparity or depth). The 2D processing of RGB data is performed next to find the checkerboard corners. Clouds of corner points are finally created (in 3D), over which an RMS error estimation is computed. We come up with a multi-platform system and its verification and evaluation has been done, using the development kit of the board nVIDIA Jetson TK1 with the MS Kinects v1/v2 and the Stereolabs ZED camera. So the main contribution is the error determination procedure that does not need any data set or benchmark, thus relying only on data acquired on-the-fly. With a simple checkerboard, our approach is able to determine the error for any device. Envisioned application is on 3D reconstruction for robotic vision, with a series of 3D vision sensors embarked in robots (UAV of type quadcopter and terrestrial robots) for high-precision map construction, which can be used for sensing and monitoring.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

This paper presents a comprehensive comparative analysis of four different computational vision algorithms for implementing an unpalleting system in a factory environment, under typical edge computing constraints. The primary objective is to automate the process of detecting and locating specific variable-shaped objects on a pallet, enabling a robotic system to accurately unstack them. The four algorithms evaluated are Pattern Matching, Scale-Invariant Feature Transform, Oriented FAST and Rotated BRIEF, and Haar cascade classifiers. Each technique is described in detail in this paper, and their implementations are outlined. Experimental results are thoroughly analyzed, assessing the algorithms’ performance based on accuracy, robustness to variability, computational speed, detection sensitivity, and resource consumption. The findings reveal the strengths and limitations of each algorithm, providing valuable insights for selecting the most appropriate technique based on the specific requirements of the unpalleting system. This research contributes to the advancement of automated object detection and localization in industrial environments, paving the way for more efficient and reliable unpalleting systems.

Это исследование сосредоточено на разработке системы искусственного зрения для гибкого дельта-робота-манипулятора и ее интеграции с межмашинной связью для оптимизации взаимодействия устройств в реальном времени. Эта интеграция направлена ​​на увеличение скорости роботизированной системы и улучшение ее общей производительности. Предлагаемое сочетание системы искусственного зрения с межмашинной связью позволяет обнаруживать и распознавать цели с высокой точностью в режиме реального времени в ограниченном пространстве, предназначенном для позиционирования, дальнейшей локализации и выполнения производственных процессов, таких как сборка или сортировка деталей. . В данном исследовании RGB-изображения используются в качестве входных данных для алгоритма MASK-R-CNN, а результаты обрабатываются в соответствии с особенностями прототипа дельта-манипулятора робота. Данные, полученные от MASK-R-CNN, адаптированы для использования в системе управления дельта-роботом с учетом ее уникальных характеристик и требований к позиционированию. Технология M2M позволяет манипулятору робота быстро реагировать на изменения, например, на перемещение объектов или изменение их положения, что имеет решающее значение для задач сортировки и упаковки. Система была протестирована в условиях, близких к реальным, чтобы оценить ее производительность и надежность.

Camouflage is a natural or artificially process to prevent an object from being detected while camouflage breaking is a countering process for the identification of the concealed object. We report that a perfectly camouflaged object in a two-dimensional scene can be retrieved and detected with stereo-vision assisted three-dimensional (3D) imaging perceived with stereopsis. The analysis is based on binocular energy model applied to general 3D settings. We show that a perfectly concealed object with random noise background can be retrieved with vision’s stereoacuity to resolve the hidden structures. The theoretical analysis is further tested and demonstrated with distant natural images taken by a drone-camera, processed with a computer and displayed in an autostereoscopy. The recovered imaging is presented with removal of the background interference to demonstrate the general applicability for camouflage breaking with stereo imaging and sensing.

Within environmental perception, automatic navigation and object detection, computer vision is a crucial and demanding field with many applications in modern industries, such as multi-target long-term visual tracking in automated production, defect detection, and driverless robotic vehicles with sensing ability. The performance of computer vision has greatly improved recently thanks to developments in deep learning algorithms and hardware computing capabilities, which has spawned the creation of a large number of related applications. This paper presents the results of a detailed review of over 50 papers published over the course of two decades (1999–2024), with a primary focus on the technical advancement of computer vision. To elucidate the foundational principles, an examination of typical visual algorithms based on traditional correlation filtering was initially conducted. Subsequently, a comprehensive overview of the most recent advancements in deep learning-based computer vision techniques was compiled. Furthermore, a comparative analysis between conventional and novel algorithms was undertaken to discuss the future trends and directions of computer vision. Lastly, the feasibility of employing visual SLAM (Simultaneous Localization and Mapping) algorithms in the context of autonomous vehicles with sensing capability was explored. Furthermore, we explored a thorough and efficient architecture for utilizing these techniques in autonomous robotic vehicles into unmanned green and low-carbon smart factories, underlining novel advances as well as potential prospects for future research.

In the last decades we have experienced great social, cultural, and educational changes, spending more time performing tasks in near vision and less hours in outdoor activities, having more overexposure to digital screens, especially the youngest and increasingly from younger ages. It is common to see cases when performing tasks in near vision the posture or position of the head is not adequate, especially the youngest, being essential to have a correct posture of the head to avoid visual, muscular, or articular problems. We present a procedure to try to control the correct position of the head in real time when performing close-up activities. The aim is to detect the inclination of the head and to know if a bad position is adopted due to a visual problem or simply to inadequate visio-postural habits, warning us of the postural anomaly to correct it.

The sTetro is a stair cleaning robot which can climb the staircase with its shapeshifting capabilities. As this robot is intended to traverse multi-floor environment autonomously, hence its localization/positioning information is an essential component of the overall system. Usually, the indoor mobile robots rely on some external system for localization information, e.g., WiFi, UWB, vision, RFID signals, or indoor Global Positioning System (GPS). This requires the installation of additional hardware and/or modification of the working environment for precise positioning information of the mobile platform. As the dimensions of the staircase are known a priori, this knowledge can be used to localize the sTetro robot on the stairs. In this article, the geometry of the staircase has been exploited to localize the robot in 3D space with measurements from the onboard time-of-flight (ToF) range sensors only. The heading angle of the robot is also estimated with two ToF sensors installed in front of the sTetro robot. Results achieved by conducting experiments on real robot prove the efficacy of the proposed approach.

Among the various types of gas sensors, the chemoresistive gas sensors based on metal oxides are considered the most attractive ones due to their simple operation, low costs and miniaturization. Thin films of V2O5 undoped and doped with TiO2 were studied as nitrogen dioxide, methane and hydrogen sensors. The experimental kinetics of the electrical conductivity changes due to introduction and removal of gas on metal oxide gas sensors were successfully explained in terms of the Langmuir adsorption theory.

Background: The laryngeal mask airway Vision Mask (LMA VM) is a supraglottic airway device (SAD) with vision guidance system. The ideal head and neck position for direct laryngoscopy is known, but the ideal position for placing a LMA is not. The objective of this study is to evaluate and compare the optimal position for placement of a video laryngeal mask airway. Methods: This was a prospective observational, transversal and analytical study of 72 consecutive patients. In the same patient, laryngeal vision was first assessed with the head and neck in the sniffing position and then with the head in the neutral position. Procedures were filmed and performed by the same investigator. Assessment of the laryngeal view was performed using two classifications: modified Cormack-Lehane classification and Brimacombe classification. Device placement was considered adequate when the Cormack-Lehane rating was scored from 1 to 2 and the Brimacombe rating was from 2 to 4. Results: 72 patients were included in this study. In the assessment of the glottis using the Cormack Lehane classification for fiberoptic view, laryngeal visibility was adequate in 64 (88.89%) patients in the neutral position and in 65 (90,28%) patients in the sniffing position (p>0,05). In the fiberoptic view of the glottis, assessed using the Brimacombe classification, laryngeal visibility was adequate in 68 (93%) patients in the neutral position and in 69 (95%) patients in the sniffing position, (p>0,05). There was no statistically significant difference in the rate of success between the sniffing position (70 patients, 97.22% success rate) and the neutral position (67 patients, 93.06% success rate) during the first insertion attempt. Two patients required a second attempt in the sniffing position, while five patients required a second attempt in the neutral position. Conclusion: An adequate sniffing position did not result in a better glottic view than neutral position, and the number and type of additional maneuvers were equal in both positions.

This work addresses the problem of automatic head pose estimation and its application in 3D gaze estimation using low quality RGB--D sensors without any subject cooperation or manual intervention. The previous works on 3D head pose estimation using RGB--D sensors require either an offline step for supervised learning or 3D head model construction which may require manual intervention or subject cooperation for complete head model reconstruction. In this paper, we propose a 3D pose estimator based on low quality depth data, which is not limited by any of the aforementioned steps. Instead, the proposed technique relies on modeling the subject's face in 3--D rather than the complete head, which in turn, relaxes all of the constraints with the previous works. The proposed method is robust, highly accurate and fully automatic. Moreover, it does not need any offline step. Unlike some of the previous works, the method only uses depth data for pose estimation. The experimental results on the Biwi head pose database confirm the efficiency of our algorithm in handling large pose variations and partial occlusion. We also evaluate the performance of our algorithm on IDIAP database for 3D head pose and eye gaze estimation.

The paper delineates the developed vision system of the UR5 cobot and the operating algorithm of the robotic quality control station. The hardware-software architecture of the developed robotic station was shown, consisting of a UR5 cobot equipped with a web camera and a stationary industrial camera with a lighting system. Image processing and analysis algorithms were described, the method of control and communication between the station components was discussed, and two operating scenarios were presented as a single robotic station and a robotic line. Based on the results obtained, the level of measurement noise, accuracy, and repeatability of the developed vision system were estimated.

This study explores novel techniques to improve the detection accuracy of skarn iron deposits using advanced image processing methodologies. Leveraging the capabilities of Aster image, Band Ratio (BR) images, and Principal Component Analysis (PCA), alongside the power of 3D Convolutional Neural Networks (3D-CNN), the research aims to enhance the precision and efficiency of ore detection in complex geological environments. The proposed method employs a specific 3D-CNN architecture, accepting input as a 7×7×C image patch, where C represents the combined number of selected Aster image bands, Principal Component (PC) bands, and computed BR images. To evaluate the accuracy of the proposed method, five distinct image bands combinations, including the proposed bands combination, were tested and evaluated based on the overall accuracy (OA), average accuracy (AA), and kappa coefficient. The results demonstrated that while the incorporation of BR images alongside Aster bands initially seemed promising, it introduced significant confusion in certain classifications, leading to unexpected mis-classification rates. Surprisingly, utilizing solely Aster bands as input parameters yielded higher accuracy rates (OA= 93.13%, AA = 91.96%, Kappa = 90.91%) compared to scenarios involving the integration with band ratios (OA = 87.02%, AA = 79.15, and Kappa = 82.60%) or the integration of BR images to PC bands (OA= 87.78%, AA = 82.39%, Kappa = 83.81%). However, the amalgamation of Aster bands with selected PC bands showed slight improvements in accuracy (OA= 94.65%, AA = 92.93%, Kappa = 93.45%), although challenges in accurately classifying certain features persisted. Ultimately, the proposed combination of Aster bands, PC bands, and BR images (proposed bands combination) presented the most visually appealing and statistically accurate results (OA = 96.95%, AA= 94.87%, and Kappa = 95.93%), effectively addressing misclassifications observed in the other combinations. These findings underscore the synergistic contributions of each of the Aster bands, PC bands, and BR images, with Aster bands proving pivotal for optimal skarn classification, PC bands enhancing intrusions classification accuracy, and BR images strengthening wall rock classification accuracy. In conclusion, the proposed combination of input image bands emerges as a robust and comprehensive methodology, demonstrating unparalleled accuracy in the remote sensing detection of skarn iron minerals.

Vision impairment may delay responses to hazards when driving. In a proof-of-concept driving simulator study, we evaluated a hazard warning device designed for vision impaired drivers. Three groups participated: 11 persons with central vision loss (CVL; median age 60 years), 12 with homonymous field loss (HFL; 52 years) and 11 with normal vision (NV; 60 years). CVL is characterised by impaired visual acuity and contrast sensitivity while HFL is a loss of vision in the same half of the visual field (blind side) in both eyes. Participants completed drives with and without the device which gave a directional vibro-tactile warning for an approaching pedestrian hazard when collision risk exceeded a pre-defined threshold. Warnings significantly (p< 0.001) reduced brake response times for CVL (∆= 0.54s) and HFL (∆= 0.30s), but not NV participants. For HFL participants, the reduction was greater (p = 0.02) for hazards on the blind (∆= 0.57s) than seeing side (∆= 0.10s). The warnings significantly reduced collision rates for CVL participants from 11 to 0% (all hazards) and for HFL participants from 30 to 1.7% (blind side hazards). Thus, hazard warnings may be beneficial in improving safety of vision impaired drivers; further research is warranted.

Graph visualization has evolved significantly over time, offering various methods to effectively represent complex data structures. This study introduces a novel force-directed algorithm for 3D data visualization, specifically tailored for commonly used datasets in linked data visualization. Leveraging the power of graph theory and methods, the algorithm aims to address the challenge of creating visually appealing and easily interpretable visualizations, which often necessitate advanced user interaction. By utilizing 3D space and the Unity Engine, the research successfully visualizes data and develops interactive visualizations, overcoming limitations of basic force-directed implementations. The main contribution of presented research is in the force-directed algorithm with springs and controlled placement as a visualization technique that combines the use of springs and attractive forces to stabilize a graph in a 3D environment. The combination of these two techniques also helps prevent the formation of a single large cluster within the graph, enhancing the overall visualization quality.

Many fields of human activity benefit from the ability to create images of obscured objects placed behind walls and to map their displacement in a noninvasive way. Usually, imaging devices like Synthetic Aperture Radars (SAR) and Ground Penetrating Radars (GPR) use expensive dedicated electronics which results in prohibitive prices. This paper presents the experimental implementation and the results obtained from an imaging system capable of performing SAR imaging and interferometric displacement mapping of targets located behind walls, as well as 3D GPR imaging using a low-cost general-purpose radar sensor. The proposed solution uses for the RF section of the system a K-band microwave radar sensor module implementing Frequency Modulated Continuous Wave operation. The low-cost sensor was originally intended for simple presence detection and ranging for domestic applications. The proposed system was tested in several scenarios and proved to operate as intended for a fraction of the cost of a commercial imaging device.

In this paper, we introduce a specialized, fully automated experimental arrangement designed for assessing the effectiveness of augmented and virtual reality technologies in healthcare setting and explore its design principles focusing on depth sensor characterization. The main goal of this project is to establish a robust benchtop platform for the quantitative evaluation of extended reality technologies in a controlled environment, emphasizing the practical assessment of augmented reality head-mounted devices. We outline a design concept and considerations for an experimental configuration aimed at creating a realistic testing environment. This apparatus comprises an observation platform mounted on a three-degree-of-freedom motorized system and a test phantom stage. Focusing on real-case scenarios, we utilized a range of sensors, including readily available range-sensing cameras and commercial augmented reality headsets, such as the Intel RealSense L515 LiDAR camera, mounted on the motion control system. The setup enabled automated data collection and facilitates controlled assessments and validation of various facets of augmented reality technologies, including object, hand, and head tracking, as well as static and dynamic image registration. This paper describes the system architecture, the process of automated data collection, and presents several evaluation studies conducted with this setup, providing insights into the quality and temporal noise associated with static or moving objects or observers in augmented reality applications.

This review delves into the growing field of flexible and stretchable strain sensors utilized in human gait analysis, focusing on determining knee bending angle and muscle activities when a human subject walks. Recent advancements have enabled these sensors to accurately capture biomechanical parameters while accommodating the body's natural movements. We examine the principles underlying these sensors' design and fabrication techniques, emphasizing their flexibility, stretchability, and biocompatibility for seamless integration into wearable systems. Through critical evaluation of existing methodologies, we assess the reliability and validity of these sensors in quantifying gait parameters. Furthermore, we discuss this technology's clinical and research implications, highlighting its potential in personalized rehabilitation and sports performance optimization. We provide an overview of flexible strain sensors and their application for analyzing human walking gait, especially for observing walking gait in rehabilitation programs. First, we present the basic working principles of various flexible strain sensors. Second, by the application of flexible strain sensors as walking gait monitoring. Finally, current challenges and future opportunities in this research area are discussed. By synthesizing current knowledge and outlining future directions, this review aims to provide insights for researchers and practitioners seeking to leverage flexible and stretchable strain sensors for comprehensive human gait analysis.

The quest for youthful, healthy skin and full, vibrant hair has long been a driving force in the dermocosmetics field. However, traditional approaches often struggle to address the underlying causes of aging, damage, and hair loss. Regenerative cosmetics, powered by skin tissue engineering, offer a transformative alternative. This review explores the emerging field of using engineered skin tissues for cosmetic purposes, focusing specifically on their potential for anti-aging, repair, and hair restoration applications. We discuss how these technologies aim to rejuvenate aging skin by promoting collagen production, reducing wrinkles, and improving overall skin function. Additionally, the use of engineered skin for wound healing and scar reduction is examined, highlighting their potential to improve the appearance and functionality of damaged skin. Finally, we advance the exciting prospects of utilizing skin tissue engineering techniques to regenerate hair follicles, potentially offering solutions for hair loss and promoting denser hair growth.

In this paper we present a city-scale (possibly global) air pollution network made of low-cost sensors for particulate matter concentration in the air. The components of presented system are based on our research and experience from previous studies focused on air quality instruments and sensors for addressing urban air pollution. Sensor nodes are produced locally and distributed over a city of Sarajevo, Bosnia and Herzegovina. The system collects, calibrates and displays particulate metal concentrations in real-time. In comparison to the available measurements from governmental institutions, our system demonstrated good agreement of measured parameters, with several advantages including: higher resolution in space and time, lower costs, both horizontal and vertical measurements and many more. One of the capabilities of the system is the real-time air pollution city map with animations. By installing multiple sensor nodes over a slope (cable car), we receive vertical measurements of temperature, humidity and particulate matter concentration in real time, which gives a valuable insight into the dynamics of temperature inversion episodes and air pollution below the inversion layer.

Dead reckoning is a promising yet often overlooked smartphone-based indoor localization technology that relies on phone-mounted sensors for counting steps and estimating walking directions, without the need for extensive sensor or landmark deployment. However, misalignment between the phone’s direction and the user’s actual movement direction can lead to unreliable direction estimates and inaccurate location tracking. To address this issue, this paper introduces SWiLoc, an enhanced direction correction system that integrates passive WiFi sensing with smartphone-based sensing to form Correction Zones. Our two-phase approach accurately measures the user’s walking directions when passing through a Correction Zone and further refines successive direction estimates outside the zones, enabling continuous and reliable tracking. In addition to direction correction, SWiLoc extends its capabilities by incorporating a localization technique that leverages corrected directions to achieve precise user localization. This extension significantly enhances the system’s applicability for high-accuracy localization tasks. Additionally, our innovative Fresnel zone-based approach, which utilizes unique hardware configurations and a fundamental geometric model, ensures accurate and robust direction estimation, even in scenarios with unreliable walking directions. We evaluate SWiLoc across two real-world environments, assessing its performance under varying conditions such as environmental changes, phone orientations, walking directions, and distances. Our comprehensive experiments demonstrate that SWiLoc achieves an average 75th percentile error of 8.89 degrees in walking direction estimation and an 80th percentile error of 1.12 meters in location estimation. These figures represent reductions of 64% and 49%, respectively for direction and location estimation error, over existing state-of-the-art approaches.

This paper presents a novel CNN-based architecture, referred to as Q-Net, to learn local feature descriptors that are useful for matching image patches from two different spectral bands. Given correctly matched and non-matching cross-spectral image pairs, a quadruplet network is trained to map input image patches to a common Euclidean space, regardless of the input spectral band. Our approach is inspired by the recent success of triplet networks in the visible spectrum, but adapted for cross-spectral scenarios, where for each matching pair there are always two possible non-matching patches; one for each spectrum. Experimental evaluations on a public cross-spectral VIS-NIR dataset shows that the proposed approach improves the state-of-the-art. Moreover, the proposed technique can also be used in mono-spectral settings, obtaining a similar performance to triplet network descriptors, but requiring less training data.

Abstract: Colistin is a last-resort antimicrobial for treating multidrug-resistant Gram-negative bacteria. Phe-notypic colistin resistance is highly associated with plasmid-mediated mobile colistin resistance (mcr) genes. mcr-bearing Enterobacteriaceae have been detected in many countries, with the emergence of colistin-resistant pathogens a global concern. This study assessed the distribution of mcr-1, mcr-2, mcr-3, mcr-4, and mcr-5 genes with the phenotypic colistin resistance in isolates from diarrheal infants and children in Bangladesh. Bacteria were identified using the API-20E biochemical panel and 16s rDNA gene sequencing. Polymerase chain reac-tions detected mcr gene variants in the isolates. Their susceptibilities to colistin were determined by agar dilu-tion and E-test by minimal inhibitory concentration (MIC) measurements. Over 30.0% (69/225) of isolates showed colistin resistance by agar dilution assessment (MIC> 2.0 μg/mL). Overall, 15.5% of isolates carried mcr genes (7, mcr-1; 17, mcr-2; 13, mcr-3; and co-occurrence occurred in 2 isolates). Clinical breakout MIC val-ues (≥ 4 μg/mL) were associated with 91.3% of mcr-positive isolates. The mcr-positive pathogens include twenty Escherichia spp., five Shigella flexneri, five Citrobacter spp., two Klebsiella pneumoniae, and three Pseudo-monas parafulva. mcr-genes appeared to be significantly associated with phenotypic colistin resistance phe-nomena (p=0.000), with 100% colistin-resistant isolates showing MDR phenomena. Age and sex of patients showed no significant association with detected mcr variants. Overall, mcr-associated colistin-resistant bacte-ria have emerged in Bangladesh, which warrants further research to determine their spread and instigate ac-tivities to reduce resistance.

This article titled "AI and IoT in Automation and Security: A Vision for Next Generation Applications," explored the implications of marrying IoT with AI in the realms of automation and security; this piece goes further into what that entails. In this paper, we present innovative application descriptions arising from this technology convergence and its future-generation applications. We found that AI brings strong cyber security, predictive maintenance, and decision-making capabilities to the table due to its advanced algorithms and machine learning models. IoT has the potential to allow businesses to extract and generate big data, automate processes, and monitor in real-time thousands and even millions of businesses at once. For now, we believe some of the possible main conclusions will be that the smart city, stand-alone systems, and user experience will be quite consumer-friendly. Importantly, the study also assessed facets such as data protection, system interoperability, and a few others. Our vision underscores the essential of a strong structure to connect the full latent of AI and IoT, finally aiming to create more capable, protected, and approachable environments. Significant results include achieving 95.8% accuracy in anomaly detection and 93.4% accuracy in predictive maintenance. The showcasing results efficacy of AI models to enhance system reliability as well as operational efficiency. Vigorous encryption protocols performance ensures data security hence addressing issues of privacy. These culminations underscore the transformative potential of AI-IoT integration in next-generation automation and security applications.

Neutral facial expression recognition is of great importance in various domains and applications. This study introduces a data-centric approach for neutral facial expression recognition, presenting a comprehensive study that explores different methodologies, techniques, and challenges in the field to foster a deeper understanding. The results show that data augmentation plays a crucial role in improving dataset performance. Additionally, the study investigates different model architectures and training techniques to identify the most effective approach, with the InceptionV3 model achieving the highest accuracy of 72%. Furthermore, the research examines the influence of preprocessing methods on the performance of both InceptionV3 and a simplified CNN model. Interestingly, the results indicate that preprocessing techniques positively affect the performance of the simpler CNN model but negatively impact the InceptionV3 model. The implemented system, used to evaluate the findings, demonstrates promising results, correctly classifying 77% of neutral expressions. However, there are still areas for improvement. Creating a specialized dataset that includes both neutral and non-neutral expressions would greatly enhance the accuracy of the system. By addressing limitations and implementing suggested improvements, neutral facial expression recognition can be significantly enhanced, leading to more effective and accurate results.

Diabetes is a major health concern that the next-generation of on-demand insulin releasing implants may overcome for personalized therapy. Therein, 3D-printed phenylboronic acid-containing subcutaneous implants with on-demand glucose-triggered drug release abilities are produced using high resolution stereolithography technology. To that end, the methacrylation of phenylboronic acid is targeted following a two-step reaction. The resulting photocurable phenylboronic acid derivative is accordingly incorporated within bioinert polyhydroxyethyl methacrylate-based hydrogels at varying loadings. The end result are sub-centimeter scaled 3D-printed bionert implants that can be remotely activated with 1,2-diols and 1,3-diols such as glucose for on-demand drug administration such as insulin. As a proof of concept, varying glucose concentration from hypoglycemia to hyperglycemia levels readily allow the release of pinacol, i.e. a model molecule with similar release properties than insulin, at respectively low and high rates. In addition, the results demonstrated that adjusting the geometry and size of the 3D-printed part is a simple and suitable method for tailoring the release behavior and dosage.

Parkinson's disease (PD) is the second most common neurodegenerative disorder, entailing several motor-related symptoms that contribute to a reduced quality of life in affected subjects. Recent advances in wearable technologies and computing resources have shown great potential for the assessment of PD-related symptoms. However, the potential applications (e.g., early diagnosis, prognosis and monitoring) and key features of digital biomarkers for motor symptoms of PD (DB-MS-PD) have not been comprehensively studied. This study aims to provide a state-of-the-art review of current digital biomarker definitions for PD, focusing on the use of wearable devices. This review systematically examines research articles from 2012 to 2024, focusing on key features and recent technologies in PD research. A total of 22 studies were included and thoroughly analyzed. Results indicate that DB-MS-PD can accurately distinguish patients with PD (PwPD) from healthy controls (HC), assess disease severity or treatment response, and detect motor symptoms. Large sample sizes, proper validation, non-invasive devices, and ecological monitoring make DB-MS-PD promising for improving PD management. Challenges include sample and method heterogeneity and lack of public datasets. Future studies can leverage evidence of the current literature to provide more effective and ready-to-use digital tools for monitoring PD.

Uveal melanoma (UM) poses a significant clinical challenge due to its high metastasis rate and poor prognosis. Melatonin, noted for its anti-cancer properties in various malignancies, including cutaneous melanoma, shows promise in UM treatment. This study aimed to evaluate melatonin receptor expression in primary UM and its association with UM-related mortality and prognostic factors. Immunohistochemical analysis of 47 primary UM tissues showed low expression of MTNR1A and MTNR1B receptors, with MTNR1A significantly higher in patients who succumbed to UM. Analysis of TCGA data from 80 UM patients revealed RNA expression for MTNR1A, RORα, and NQO2, but not MTNR1B or GPR50. Higher MTNR1A RNA levels were observed in patients with a BAP1 mutation, and higher NQO2 RNA levels were noted in patients with the epithelioid tumor cell type. However, Kaplan-Meier analysis did not show distinct survival probabilities based on receptor expression. The study concludes that UM clinical samples express melatonin receptors, suggesting a potential mechanism for melatonin's anti-cancer effects. Despite finding higher MTNR1A expression in patients who died of UM, no survival curve differences were observed. Further research is needed to explore additional mechanisms of melatonin’s oncostatic effects, including its antioxidant properties and immune modulation.

Computational animation of spatiotemporal models for 3-D shape and motion is considered as core of dynamic real-time vision. This is based on sets of features evaluated from multi-focal image streams. Subjects are defined as special objects capable of sensing environmental parameters and of initiating own actions in combination with stored knowledge. Object/subject recognition and scene understanding are achieved on different levels. Multiple objects are tracked individually for perceiving their actual state (‘here and now’). Fast saccadic jumps in gaze direction allow flexible concentration on objects or parts of actual interest. By analyzing motion of relevant objects/subjects over a larger time scale on the level of state variables and documenting them in the ‘scene tree representation’ (computer graphics), the situation with respect to decision making is assessed. Various behavioral capabilities of subjects are represented on an abstract level for characterizing their potential behaviors. These are generated by stereotypical feed-forward and feedback control applications on a separate level close to the actuator hardware with corresponding methods. This dual representation on one level for decision making and one on the implementation level allows for flexibility and easy adaptation or extension. Results are shown for road vehicle guidance based on three cameras on a gaze-controlled platform.

For centuries, Foeniculi fructus (F. fructus) has been used as a traditional herbal medicine in China and Europe and is widely used as a natural therapy for digestive disorders, including indigestion, flatulence, and bloating. The mechanism by which F. fructus alleviates functional dyspepsia was analyzed through network pharmacology, and its therapeutic effect on an animal model of functional dyspepsia was investigated. The compounds, targets, and related diseases of F. fructus were studied utilizing the traditional Chinese medicine systems pharmacology (TCMSP) database. Information on the target genes was classified using the UniProt database. A network was built using Cytoscape 3.9.1, and functional dyspepsia-related genes were checked using the Cytoscape string application. The efficacy of F. fructus on functional dyspepsia, including gastroparesis and gastrointestinal motility, was confirmed by treatment with its extract in a mouse model of loperamide-induced functional dyspepsia. Seven compounds targeted twelve functional dyspepsia-associated genes. In a functional dyspepsia mouse model, F. fructus significantly suppressed the symptoms when compared to that in the control group. Our animal studies showed that the mechanism of action of F. fructus is closely related to gastrointestinal motility. Based on animal experimental results, the results showed that F. fructus provides a potential means to treat functional dyspepsia, suggesting that its medical mechanism for functional dyspepsia can be described by the relationship between seven key compounds of F. fructus, including oleic acid and β-sitosterol, and 12 functional dyspepsia-related genes.

Reconstructing 3D indoor scenes from 2D images has always been an important task in computer vision and graphics applications. For indoor scenes, traditional 3D reconstruction methods suffer from the lack of surface details, poor reconstruction of large flat surface textures and areas with uneven lighting, and many falsely reconstructed floating debris noises in the reconstructed models. We add adaptive normal priors to the neural implicit reconstruction process to optimize the network, and improve the accuracy of volume density prediction by adding regularization terms to the neural radiation field to constrain the volume density obtained by weight distribution, and learn a smooth SDF surface from the network to obtain an explicit mesh model. Experiments show that the method proposed in this paper outperforms the state-of-the-art methods on ScanNet, Hypersim, and Replica datasets.

Many accidents, such as those involving collisions or trips, appear to involve failures of vision; but the association between accident risk and vision as conventionally assessed, is weak or absent. We addressed this conundrum by embracing the distinction inspired by neuroscientific research, between vision for perception and vision for action. A dual-process perspective predicts that accident vulnerability will be associated more strongly with vision for action than vision for perception. Older and younger adults, with relatively high and relatively low self-reported accident vulnerability (Accident Proneness Questionnaire), completed three behavioural assessments targeting: vision for perception (Freiburg Visual Acuity Test); vision for action (Vision for Action Test - VAT); and the ability to perform physical actions involving balance, walking and standing (Short Physical Performance Battery). Accident vulnerability was not associated with visual acuity or with performance of physical actions; but was associated with VAT performance. VAT assesses the ability to link visual input with a specific action –launching a saccadic eye movement as rapidly as possible, in response to shapes presented in peripheral vision. The predictive relationship between VAT performance and accident vulnerability was independent of age, visual acuity and physical performance scores. Applied implications of these findings are considered.

Traditional computer vision techniques aim to extract meaningful information from images but often depend on manual feature engineering, making it difficult to handle complex real-world scenarios. Fractional Calculus (FC), which extends derivatives to non-integer orders, provides a flexible way to model systems with memory effects and long-term dependencies, making it a powerful tool for capturing fractional rates of variation. Recently, Neural Networks (NNs) have demonstrated remarkable capabilities in learning complex patterns directly from raw data, automating computer vision tasks and enhancing performance. Therefore, the use of fractional calculus in neural network-based computer vision is a powerful method to address existing challenges by effectively capturing complex spatial and temporal relationships in images and videos. This paper presents a survey of Fractional Calculus Neural Network-based (FC NN-based) computer vision techniques for denoising, enhancement, object detection, segmentation, restoration, and NN compression. The survey compiles existing FFC NN-based approaches, elucidates underlying concepts, and identifies open questions and research directions. By leveraging FC's properties, FC NN-based approaches offer a novel way to improve the robustness and efficiency of computer vision systems.

We present a novel method for online measurement of multi-point opening distances of midpalatal suture during rapid palatal expansion (RPE) using fiber optic Fabry-Perot (F-P) sensors. The sensor consists of an optical fiber with a cut flat end face and an optical reflector, which are implanted into the palatal base structure of an expander and is capable of measuring the precise distance between two optical reflective surfaces. As a demonstration, a 3D printed skull model containing the maxilla and zygomaticomaxillary complex (ZMC) was produced and a miniscrew-assisted rapid palatal expander (MARPE) with two guide rods was used to generate the midpalatal suture expansion. The reflected spectrums of the sensors were used to dynamically extract cavity length information for full process monitoring of expansion. The dynamic opening of the midpalatal suture during the gradual activation of the expander was measured, and a displacement resolution of 2.5 μm was demonstrated. The angle of expansion was derived and the results suggested that the midpalatal suture was opened with a slightly V type expansion of 0.03 rad at the first loading and subsequently expanded in parallel. This finding might be useful for understanding the mechanical mechanisms that lead to different types of expansion. The use of a fiber-optic sensor for mounting the rapid palatal expander facilitates biomechanical studies and experimental and clinical evaluation of the effects of RPE.

The TRPV3 calcium ion channel is vital for maintaining skin health and has been associated with various skin-related disorders. Since TRPV3 is involved in the development of skin inflammation, inhibiting TRPV3 could be a potential treatment strategy. Alpha-mangostin isolated from Garcinia mangostana L. extract exhibits diverse positive effects on skin health; however, the underlying mechanisms remain obscure. This study investigated the TRPV3-inhibitory properties of alpha-mangostin on TRPV3 hyperactive mutants associated with Olmsted syndrome and its impact on TRPV3-induced cytokine secretion and cell death. Our findings demonstrate that alpha-mangostin effectively inhibits TRPV3, with an IC50 of 0.077 ± 0.013 μM, showing inhibitory effects on both wild-type and mutant TRPV3. TRPV3 inhibition with alpha-mangostin decreased calcium influx and cytokine release, protecting cells from TRPV3-induced death. These results indicate that alpha-mangostin reduced inflammation in TRPV3-activated skin keratinocytes, suggesting that alpha-mangostin could be potentially used for improving inflammatory skin conditions such as dermatitis.

A study of curvature along the contour provides important sources of information about the shape of an object. Knowledge of contour curvature allows for the perception of and interaction with 3D objects. In this review, we will explore the value of contour curvature in the field of neurophysiology, psychophysics, computer vision, and psychology. The serial consolidation of disjoint edges, oriented in a particular manner, into composited curves allows building of identifiable shapes in occluded natural environments [Hess1999, Wertheimer1923, Zucker1989, Feldman2001]. Examples are our ability to pick objects, sort and manage shapes otherwise hidden or confounded by occlusion in messy natural environments. Contour curvature has been intensively studied in psychology as it forms the first steps in 2D shape building which eventually becomes 3D object recognition in the human brain.

Microscopic vision plays an important role in automated micro-assembly. However, some uncertain factors in the assembly process, such as occlusion and stains can lead to the mistakes of feature extraction. Herein, to solve the problem, the deep learning techniques are introduced into the feature recognition tasks, focusing on the attention mechanism and visualizing CNNs for DL-based microscopic vision. The main contributions are summarized as follows: The CBAM attention mechanism is combined with the YOLOv5 algorithm to improve the accuracy and robustness of feature extraction. The micropart feature occlusion experiment results show that at 70% occlusion degree, YOLOV5-CBAM can reach 97.9% [email protected], which is 4.6% higher than the original one. Visualization analysis of DL-based model is conducted using Grad-CAM to make the decision result more transparent and avoid potential visual detection risks during assembly. The heatmap matching degree between GT area and high-light area is increased by 27.81% on average, which further verify the effectiveness of attention mechanism in micropart feature localization. Additionally, micropart surface stain and droplet quality classification models based on ResNet50 are trained to replace the manual sorting. The visual results are consistent with human eye discernment and judgement, confirming the reliability of parts and droplets sorting.

Introduction: Obstructive sleep apnea syndrome (OSAS) is characterized by recurrent episodes of upper airway obstruction and involves intermittent hypoxia and sleep fragmentation, with potentially serious consequences for affected patients. (1–3). Although nocturnal polysomnography is the gold standard, it is an exam that is not readily available and is very expensive. (4). Hence, the need to find new diagnostic methods. Considering that the causes of OSAS can be divided into anatomical-structural ones, related to craniofacial anomalies, it has been hypothesized that anthropometric measurements taken by new 3D stereophotogrammetric systems could be useful as a diagnostic tool in pediatric patients with OSAS (5) (6). The primary objective of the study is, therefore, to evaluate the correlation between mandibular length measured between menton and gonion, obtained through 3D stereophotogrammetry using the "Face Scanner maxi 6", and the severity of OSAS (AHI classification), defined by the score of the Sleep Clinical Record (SCR) questionnaire in a group of pediatric patients with suspected obstructive sleep disorders. The secondary objective concerns the identification of possible correlations between other mandibular parameters estimated by 3D stereophotogrammetry and the severity of OSAS, defined by the McGill Oximetry Score (MOS), and the association between MOS and SCR to determine the AHI level. Materials and methods: The study considered patients who were prescribed a pulseoximetry exam due to suspected obstructive sleep disorders. All participating patients underwent a specialized orthodontic examination, which included completing the SCR questionnaire and taking facial photographs using a 3D stereophotogrammetric system. The SCR questionnaire considers 11 dental, nasal, oropharyngeal, and facial phenotype parameters to determine a final score from 0 to 18, indicating the risk of obstructive sleep apnea syndrome. The acquired stereophotogrammetric images were processed using dedicated software to obtain a three-dimensional model representing the patient's facial phenotype. Subsequently, anatomical landmarks and relevant anthropometric measurements were identified on the model, and it was assessed whether one or more of these showed concordance criteria with the parameters derived from SCR and MOS. The anthropometric evaluation was performed by expert operators, taking into account mandibular variables. Results: Fifteen patients were analyzed, with 2 excluded due to alterations in the stereophotogrammetric images caused by poor patient cooperation during the acquisition of the photographs. Spearman's correlation analysis was performed to investigate the relationship between anthropometric measurements, obtained by 3D stereophotogrammetry, and OSAS severity, by means of SCR, MOS, and SCR+MOS. A significant and negative correlation was observed between right mandibular length (gonion-menton) and MOS (ρ=−0.586, p=0.036). Conclusions: The result obtained has important implications for the field of study and suggests that future attention should focus more on the mandibular length variable as a determining factor for OSAS. However, the sample examined was relatively small, which might obscure the correlation with contralateral mandibular length and potential correlations with other mandibular/facial parameters. Additionally, the small sample size prevented stratification by sex and age. The study thus provides an important contribution to understanding the relationships between 3D stereophotogrammetry and pediatric OSAS but also highlights the need for further research that could potentially influence future developments in diagnosing OSAS in children.

Traditional 3D reconstruction models have consistently encountered a challenge: attaining high recall of object edges while preserving precision. In this paper, we introduce a post-processing method Multi-Head Attention Refiner (MA-R) aimed at tackling this challenge by integrating a multi-head attention mechanism within the U-Net style refiner module. The 3D reconstruction model applying this method demonstrates excellence in parsing intricate image details, resulting in significant enhancement of boundary predictions and increased recall rates. In our experiments, our method significantly enhances the reconstruction performance of Pix2Vox++ when multiple images are utilized as input. Specifically, it achieves an enhanced Intersection Over Union score of approximately 1.1% compared to the original Pix2Vox++ model when 16-view images are employed.

Vertical Indoor Farming (VIF) with hydroponics offers a promising perspective for sustainable food production. Intelligent control of VIF system components plays a key role in reducing operating costs and increasing crop yields. Modern machine vision (MV) systems use Deep Learning (DL) in combination with camera systems for various tasks in agriculture, such as disease and nutrient deficiency detection, and flower and fruit identification and classification for pollination and harvesting. This study presents the applicability of MV technology with DL modelling to detect the growth stages of chilli plants using YOLOv8 networks. The influence of different bird’s eye and side view datasets and different YOLOv8 architectures was analysed. To generate the image data for training and testing the YOLO models, chilli plants were grown in a hydroponic environment and imaged throughout their life cycle using four camera systems. The growth stages were divided into growing, flowering and fruiting classes. All trained YOLOv8 models showed reliable identification of growth stages with high accuracy. The results indicate that models trained with data from both views show better generalisation. YOLO’s middle architecture achieved the best performance.

Among magnetoelectric (ME) heterostructures, ME laminates of the type Metglas-like / PVDF (magnetostrictive+piezoelectric constituents) have shown the highest induced ME voltages, usually detected at the magnetoelastic resonance of the magnetostrictive constituent. This ME coupling happens because of the high cross-correlation coupling between magnetostrictive and piezoelectric material, and is usually associated with a promising application scenario for sensors or actuators. In this work we detail the basis of the operation of such devices, as well as some arising questions (as size effects) concerning their best performance. Also, some examples of their use as very sensitive magnetic fields sensors or innovative energy harvesting devices will be presented At the end, the challenges, future perspectives and technical difficulties that will determine the success of ME composites for sensor applications are discussed.

Gas sensing is crucial for detecting hazardous gases in industrial environments, ensuring safety and preventing accidents. Additionally, it plays a vital role in environmental monitoring and control, helping to mitigate pollution and protect public health. Integrated photonic gas sensors are important due to their high sensitivity, rapid response time, and compact size, enabling precise recognition of gas concentrations in real-time. These sensors leverage photonic technologies, such as waveguides and resonators, to enhance performance over traditional gas sensors. Advancements in materials and fabrication techniques could further improve their efficiency, making them invaluable for environmental monitoring, industrial safety, and healthcare diagnostics. In this review, we delved into photonic gas sensors that operate based on the principles of evanescent field absorption (EFA) and wavelength interrogation methods. These advanced sensing mechanisms allow for highly sensitive and selective gas detection, leveraging the interplay of light with gas molecules to produce precise measurements.

With the development of organizational biology and forced from the EU Cosmetic Regulation (EU/1223/2009) with the complete ban of animal testing for cosmetic purposes, 3D skin models have been widely developed due to their similar physiological structure and metabolic function to native human tissue. 3D skin models for in vitro cosmetic evaluation are still promising alternative methods for evaluating phototoxicity, corrosivity and irritation. These models have been used for early screening and later validation of toxicity and efficacy evaluation by many well-known cosmetic companies. 3D skin models have become an important tool in cosmetic evaluation research. This article reviews the development of 3D skin models and their application in cosmetic evaluation. An outlook on the current application and future technological development directions in the cosmetic field is also presented.

The purpose of this study is to show an automated laser vision correction (LVC) with the transep-ithelial refractive keratectomy (TransPRK) surgery technique. Since more surgical steps have been automated over the years, we have standardized the TransPRK technique. We have been using it since 2010. This paper aims to illustrate the processes that are readily applicable to automation. To meet the patient's expectations and ensure that the patient has uncorrected visual acuity at least equal to the preoperative corrected vision with glasses, patient selection is crucial in refractive surgical procedures. One major benefit of automating the surgery is that it can be performed in a similar way by each surgeon or laser correction centre, so once the standard and results are good, these can be per-formed by different surgeons.

The work aims to develop an electromagnetic shielding measurement methodology and design an electromagnetic shielding effectiveness test setup for thin sheet material testing. In brief, multiple shielding effectiveness standards are described and analyzed in the thin sheet material testing framework. Two types of the developed shielding effectiveness test probe in high and low-frequency ranges are validated comprehensively. Extensive descriptions and data of developed testing methodology are also reported.

The monocular structured light measurement system has low cost, simple algorithms, and a wide measurement range, making it widely applicable in multiple fields. However, in practical applications, the system may be affected by various factors including noise, non-linear intensity, changes in the reflectivity of the object being measured, and the calibration method and accuracy of the system, thereby reducing the measurement accuracy. In order to solve these issues, this paper proposes a new monocular structured light measurement method, mainly comprises the following two points: (a) A denoising algorithm for phase images based on DAE is proposed, which calculates the wrapped phase of the phase-shifted fringes after initial denoising by DAE. Then, a new phase-shifted fringe pattern is generated and input into DAE for iterative denoising, achieving high-performance image denoising and high-precision wrapped phase solution. (b) A new absolute phase height calibration algorithm is proposed, which introduces camera internal and external parameters and uses a two-layer feedforward network to directly establish the relationship between phase and the 3D coordinate system. Without the need for high-precision motion platforms, high-precision phase height calibration is attainable. In general, compared to conventional methods, the experimental results indicate the effectiveness of the proposed method for low-quality phase-shifted fringe 3D reconstruction. In addition, the measurement method described in this article also demonstrates effectiveness in high-dynamic scenes.

In this work, an innovative numerical approach for polylinear approximation (polylinearization) of non-self-intersecting compact sensor characteristics (transfer functions) specified either pointwise or analytically is introduced. The goal is to optimally partition the sensor characteristic, i.e. to select the vertices of the approximating polyline (approximant) along with their positions on, the sensor characteristics so that the distance (i.e. the separation) between the approximant and the characteristic is rendered below a certain problem-specific tolerance. To achieve this goal, two alternative non-linear optimization problems are solved, whose essential difference is in the adopted quantitative measure of the separation between the transfer function and the approximant. In the first problem, which relates to absolutely integrable sensor characteristics (their energy is not necessarily finite, but they can be represented in terms of convergent Fourier series), the polylinearization is constructed by numerical minimization of the L^1--metric (a distance-based separation measure), concerning the number of polyline vertices and their locations. In the second problem which covers the quadratically integrable sensor characteristics (whose energy is finite, but they do not necessarily admit a representation in terms of convergent Fourier series), the polylinearization is constructed by minimizing numerically the L^2-metric (area-, or energy-based separation measure) for the same set of optimization variables –the locations, and the number of polyline vertices.

Due to the inherent limitations of a single viewpoint, reconstructing 3D human meshes 1 from a single image has long been a challenging task. While deep learning networks enable us to 2 approximate the shape of unseen sides, capturing the texture details of the non-visible side remains 3 difficult with just one image. Traditional methods utilize Generative Adversarial Networks (GANs) 4 to predict the normal maps of the non-visible side, thereby inferring detailed textures and wrinkles 5 on the model’s surface. However, we have identified challenges with existing normal prediction 6 networks when dealing with complex scenes, such as a lack of focus on local features and insufficient 7 modeling of spatial relationships.To address these challenges, we introduce EMAR—Enhanced 8 Multi-scale Attention-driven Single Image 3D Human Reconstruction. This approach incorporates 9 a novel Enhanced Multi-Scale Attention (EMSA) mechanism, which excels at capturing intricate 10 features and global relationships in complex scenes. EMSA surpasses traditional single-scale attention 11 mechanisms by adaptively adjusting the weights between features, enabling the network to more 12 effectively leverage information across various scales.Furthermore, we have improved the feature 13 fusion method to better integrate representations from different scales. This enhanced feature fusion 14 allows the network to more comprehensively understand both fine details and global structures 15 within the image. Finally, we have designed a hybrid loss function tailored to the introduced attention 16 mechanism and feature fusion method, optimizing the network’s training process and enhancing the 17 quality of reconstruction results.Our network demonstrates significant improvements in performance 18 for 3D human model reconstruction. Experimental results show that our method exhibits greater 19 robustness to challenging poses compared to traditional single-scale approaches.

This study introduces a sophisticated neural network structure for segmenting breast tumors. It achieves this by combining a pretrained Vision Transformer (ViT) model with a U-Net framework. The U-Net architecture, commonly employed for biomedical image segmentation, is further enhanced with Depthwise Separable Convolutional Blocks to decrease computational complexity and parameter count, resulting in better efficiency and less overfitting. The Vision Transformer, renowned for its robust feature extraction capabilities utilizing self-attention processes, efficiently captures the overall context within images, surpassing the performance of conventional convolutional networks. By using a pretrained ViT as the encoder in our U-Net model, we take advantage of its extensive feature representations acquired from extensive datasets, resulting in a major enhancement in the model’s ability to generalize and train efficiently. The suggested model has exceptional performance in segmenting breast cancers from medical images, highlighting the advantages of integrating transformer-based encoders with efficient U-Net topologies. This hybrid methodology emphasizes the capabilities of transformers in the field of medical image processing and establishes a new standard for accuracy and efficiency in activities related to tumor segmentation.

Flexible wearable pressure sensors offer numerous benefits, including superior sensing capabilities, a lightweight and compact design, and exceptional conformal properties, making them highly sought after in various applications including medical monitoring, human-computer interaction, and electronic skin. Because of their excellent characteristics, such as simple fabrication, low power consumption, and short response time, capacitive pressure sensors have received widespread attention. As a flexible polymer material, polydimethylsiloxane (PDMS) is widely used in the preparation of dielectric layers for capacitive pressure sensors. The Young's modulus of the flexible polymer can be effectively decreased through the synergistic application of sacrificial template and laser ablation techniques, thereby improving the functionality of capacitive pressure sensors. In this study, a novel sensor was developed through a series of processes including sacrificial template method using NaCl microparticles, CO₂ laser ablation, and sandwiching a porous PDMS dielectric layer between two flexible electrodes to create a capacitive pressure sensor. The sensor demonstrates a sensitivity of 0.694 kPa-1 within the pressure range of 0-1 kPa, and can effectively detect pressures ranging from 3 Pa to 200 kPa. The sensor demonstrates stability for up to 500 cycles, with a rapid response time of 96ms and a recovery time of 118ms, coupled with a low hysteresis of 6.8%. Furthermore, our testing indicates that the sensor possesses limitless potential for use in detecting human physiological activities and signaling emergencies.

Plant leaf area index (LAI) is a key characteristic affecting field canopy microclimate. In addition to traditional professional measuring instruments, smartphone camera sensors have been used to measure plant LAI. However, when smartphone methods were used to measure conifer forest LAI, very different performances were obtained depending on whether the smartphone was held at the zenith angle or at a 57.5° angle. To validate further the potential of smartphone sensors for measuring conifer LAI and to find the limits of this method, this paper reports the results of a comparison of two smartphone methods with an LAI-2000 instrument. It is shown that both methods can be used to reveal the conifer leaf-growing trajectory. However, the method with the phone oriented vertically upwards always produced better consistency in magnitude with LAI-2000. The bias of the LAI between the smartphone method and the LAI-2000 instrument was explained with regard to four aspects that can affect LAI: gap fraction, leaf projection ratio, sensor field of view (FOV), and viewing zenith angle (VZA). It was concluded that large FOV and large VZA cause the 57.5° method to overestimate the gap fraction and hence underestimate conifer LAI, especially when tree height is greater than 2.0 m. For the vertically upward method, the bias caused by the overestimated gap fraction is compensated for by an underestimated leaf projection ratio.

Elbow dislocation and instability present significant clinical challenges, necessitating a thorough understanding of the underlying bio-mechanical mechanisms. In this study, a quasi-static three-dimensional finite element model of the human elbow joint is developed to investigate stress distribution and stages of dislocation in the human elbow under various loading conditions. The model simulates the elbow joint in different degrees of flexion (30°, 45°, 60°, and 90°) and forearm positions (pronation and supination), providing detailed insights into the progression of dislocation. Significant findings include the identification of high stress concentrations on the humerus at 90° flexion and on the radial and coronoid processes at 30°, 45°, and 60° flexion. Three reproducible stages of dislocation were observed, particularly in flexed positions with forearm pronation or supination. These stages align with experimental observations and highlight the initial occurrence of bony failures, such as radial head and ulnar coronoid fractures, preceding soft tissue tears. Clinically, the study underscores that early-stage low-impact posterior elbow dislocations retain enough stability to be managed with closed reduction and early mobilization. However, as dislocations progress, significant damage to the medial and lateral collateral ligaments is expected, necessitating more invasive treatments. This research provides valuable bio-mechanical insights into elbow dislocation, aiding in the development of improved treatment strategies and enhancing patient outcomes through precise and timely clinical interventions. The validated FEM serves as a powerful tool for pre-surgical planning offering a comprehensive understanding of elbow joint mechanics.

With the development of agriculture, the complexity and dynamism of orchard environments pose challenges to the perception and positioning of inter row environments for agricultural machinery. The paper proposes a method for extracting navigation lines and measuring pedestrian obstacles. The improved YOLOv5 algorithm is used to detect tree trunks between left and right rows in orchards. The experimental results show that the average angle deviation of the extracted navigation lines is less than 5 degrees, verifying its accuracy. Due to the variable posture of pedestrians and ineffective camera depth, a distance measurement algorithm based on four zone depth comparison is proposed for pedestrian obstacle distance measurement. Experimental results show that within a range of 6m, the average relative error of distance measurement does not exceed 1%, and within a range of 9m, the maximum relative error is 2.03%. The average distance measurement time is 30 milliseconds, which can accurately and quickly achieve pedestrian distance measurement in orchard environments. On the publicly available TUM RGB-D dynamic dataset, YOLOD-SLAM2 significantly reduces the RMSE index of absolute trajectory error compared to ORB-SLAM2 algorithm, which is less than 0.05 m/s. In actual orchard environments, YOLOD-SLAM2 has a higher degree of agreement between the estimated trajectory and the true trajectory when the car is traveling in straight and circular directions. The RMSE index of the absolute trajectory error is less than 0.03m/s, and the average tracking time is 47ms, indicating that the YOLOD-SLAM2 algorithm proposed in this paper can meet the accuracy and real-time requirements of agricultural machinery positioning in orchard environments.

The assortment of low-cost 3D printers for “in-practice” use, e.g., for clear aligner therapies, is ever increasing. To address concerns about the accuracy of orthodontic models produced on such printers when cost efficient modes of 3D printing are employed, this study examined the effect of print model body type and print angulation on accuracy. Six printing-configuration groups were included: 2 model types (solid or hollow shell) combined with 3 print angles (0°, 70°, or 90°) with 10 models/group; all models were printed with 100-µm layer thickness using a digital light processing-based 3-dimensional printer. Eleven selected structures and distances were measured on the printed models with a digital microscope and compared to the same measures on a digitized master model. The clinically-acceptability range was set at ±0.25 mm difference from the master model for single tooth measurements (intra-tooth) and ±0.5 mm for cross-arch measurements (inter-tooth). For individual measurements across all models, 98% fell within clinical acceptability. For mean measurements within each model group, only canine height for the shell-0° model had a mean difference (0.26 mm ± 0.03) outside the clinically acceptable range for intra-tooth measurements. Standard deviations for all intra-tooth measurements were within 0.07 mm. While none of the mean inter-tooth measurements exceeded the acceptability range, the standard deviations were larger (0.04 to 0.30 mm). Accuracy of orthodontic models for clear aligner therapies was not impacted beyond the clinically acceptable range when altering model body type and print angulation to improve efficiency of 3D printing. These findings suggest greater flexibility of the practitioner to alter print settings to address time and cost efficiency in various clinical scenarios and still maintain clinically acceptable model accuracy.

Computer vision is a fast-expanding discipline focusing on analyzing, altering, and comprehending images at a high level. Its goal is to figure out what's going on in front of a camera and use that knowledge to manage a computer or robotic system or to show people new visuals that are more instructive or attractive than the original camera photos. Video surveillance, biometrics, automotive, photography, movie production, Web search, medicine, augmented reality gaming, new user interfaces, and many other applications are all possible with computer vision technologies. This paper aims to describe how computer vision will be used to play a winning game of blackjack.

Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

Enclosed public spaces are the hotspots for airborne disease transmission. To measure and maintain indoor air quality in terms of airborne transmission, an open source, low cost and distributed array of Particulate Matter Sensors has been developed and named as Dynamic Aerosol Transport for Indoor Ventilation or DATIV system. This system can use multiple Particulate Matter Sensors (PMS) simultaneously and can be remotely controlled using a Raspberry Pie based operating system. The data acquisition system can be easily operated using the GUI within any common browser installed on a remote device such as a PC or Smartphone with corresponding IP address. The software architecture and validation measurements are presented together with possible future developments.

Contaminants of Emerging Concern (CECs), a new category of contaminants in limelight, is a major issue of global concern. The pervasive nature of CECs and its harmful effects, such as cancer, reproductive disorders, neurotoxicity etc., make the situation alarming. The perilous nature of CECs lies in the fact that even very small concentration of CECs can cause great impacts on living beings. It also has a nature of bioaccumulation. Thus, it is the ultimate need to have efficient sensors for detection of CECs to ensure safe living environment. Electrochemical sensors are an efficient platform for CEC detection as they are highly selective, sensitive, stable, reproducible, and prompt, and can detect very low concentrations of analyte. Major classes of CECs are pharmaceuticals, illicit drugs, personal care products, endocrine disruptors, newly registered pesticides, and disinfection by-products. This review focusses on CECs, including their sources and pathways, health effects caused by them, and electrochemical sensors as reported in literatures under each category for the detection of major CECs.

Identifying punch types as part of punch kinematic analysis is a key component for both coaches and players, providing critical insights into the variety and effectiveness of punches, which are essential for refining overall performance. Existing research indicates that punch type classification typically relies on data from either wearables or video data. Both approaches have their merits and demerits but require a significant amount of labeled data for modeling the classification algorithm. In this work, we propose a novel approach that significantly reduces the labeling effort by one-sixth by leveraging video data to enhance the training information of sensor data. This enriched training phase enables more accurate punch classification with reduced labeled data. Subsequently, the real-time punch identification and classification use only the wearable data. On a real dataset, with 15% of the labeling efforts, our approach achieved an accuracy rate of 91.41% for rear hand punch recognition and 91.91% for lead hand punch recognition, along with 92.33% and 94.56% for punch classification, respectively. Through the development of our Smart Boxer system, we aim to revolutionize punch analytics in boxing, providing comprehensive insights while enhancing the overall training and competitive experience for athletes and enriching fan engagement with the sport.

Bioimpedance imaging aims to generate a 3D map of the resistivity and permittivity of biologi-cal tissue from multiple impedance channels measured with electrodes applied to the skin. When the electrodes are distributed around the body (for example, by delineating a cross-section of the chest or a limb), bioimpedance imaging is called electrical impedance tomography (EIT) and results in 2D functional images. Conventional EIT systems rely on individually cabling each electrode to master electronics in a star configuration. This approach works well for rack-mounted equipment; however, the bulkiness of the cabling is unsuitable for a wearable system. Previously presented cooperative sensors solve this cabling problem using active (dry) elec-trodes connected via a two-wire parallel bus. The bus can be implemented with two unshielded wires or even two conductive textile layers, thus replacing the cumbersome wiring of the con-ventional star arrangement. Prior research demonstrated cooperative sensors for measuring bi-oimpedances, successfully realizing a measurement reference signal, sensor synchronization, and data transfer though still relying on individual batteries to power the sensors. Subsequent research using cooperative sensors for biopotential measurements proposed a method to re-move batteries from the sensors and have the central unit supply power over the two-wire bus. Building off our previous research, this paper presents this method applied to the measurements of bioimpedances. Two different approaches are discussed, one using discrete, commercially available components, and the other with an application specific integrated circuit (ASIC). Initial experimental results reveal that both approaches are feasible, but the ASIC approach offers ad-vantages for medical safety, as well as lower power consumption and smaller size.

Aiming at effectively generating safe and reliable motion paths for quadruped robots, a hierar-chical path planning approach driven by dynamic 3D point cloud is proposed in this article. The developed path planning model is essentially constituted of two layers: global path planning layer and local path planning layer. At the global path planning layer, a new method is proposed for calculating terrain potential field based on point cloud height segmentation. Variable step size is employed to improve the path smoothness. At the local path planning layer, a real-time prediction method for potential collision area and a strategy for temporary target point selection is developed. Quadruped robot experiments were carried out in an outdoor complex environment. The experi-mental results verified that, for global path planning, the smoothness of the path is improved and the complexity of the passing ground is reduced. The effective step size is increased by a maxi-mum of 13.4 times, and the number of iterations is decreased by up to 1/6, compared with the traditional fixed step size planning algorithm. For local path planning, the path length is short-ened by 20%, more efficient dynamic obstacle avoidance and more stable velocity planning are achieved by using the improved dynamic window approach (DWA).

Computer vision is considered as an ally to solve business problems that require human intervention, intelligence and criteria. This topic of research has evolved in XXI century at faster peace, delivering various alternatives from open source until commercial platforms. With so many options and market growing, it result difficult to make a decision on which one to use, or even worse, realize it was not suited for different scenarios. In this paper we analyze five options selected arbitrarily and tested on a dataset of 755 images to detect persons in an image, using object detectors. We analyze elapsed time to process an image, error with observations by humans, number of persons detected, correlation of time and person density, object detected size and F1 Score, considering precision and recall. As we found there are score ties and similar behaviors among options available, we introduce a novel index that takes in consideration the number of persons and their pixel size, to propose the Vision Acuity Index of Computer Vision. The results demonstrate this is a good option to serve as indicator to make decisions. Also, this index proposed have a potential to be expanded for different business use cases, and to measure new proposed algorithms in the future along with the traditional metrics used previously.

Recent advances in organoid technology have revolutionized cancer biology and thera-peutic interventions, offering personalized immunotherapy treatment. Organoids, three-dimensional cell cultures derived from patient tumors, accurately replicate the tumor microenvi-ronment, providing unprecedented insights into tumor-immune interactions and therapeutic re-sponses. In this literature-based study, we discuss various culture methods for the diverse appli-cations of organoids in cancer immunotherapy, including drug screening, personalized treatment strategies, and mechanistic studies. Additionally, we address the technological challenges asso-ciated with these methods and propose potential future solutions to accelerate the development of novel immunotherapeutic approaches. This review highlights the transformative potential of or-ganoid models in advancing preclinical cancer immunotherapy modeling, screening, and evalua-tion, paving the way for more effective and personalized cancer treatments.

This paper explores the application of machine learning (ML) in predicting functional recovery in patients with ischemic stroke. As technology advances, ML shows significant potential in the field of stroke medicine, especially in the areas of big data analytics and personalized medicine. Studies have shown that ML algorithms can improve the accuracy of stroke image analysis, subtype classification, risk assessment, treatment guidance, and prognosis prediction. However, the widespread use of ML still faces challenges such as data standardization, model validation, privacy, and bias. This paper reviews the current application status of ML in the field of stroke, discusses the challenges faced, and looks forward to the future development direction, aiming to promote the practical application of ML technology in the diagnosis and treatment of stroke to improve the prognosis and quality of life of patients.

Sinkhole formation caused by leaking pipes in karst soluble rocks is a significant concern, leading to infrastructure damage and safety risks. In this paper, an experiment was conducted to investigate sinkhole formation in dense sand induced by a leaking pipe. Fibre Bragg gratings (FBGs) sensors were used to record the strain. A balloon was gradually deflated within a bed of wet silica sand to create an underground cavity. Eighteen FBG sensors, with a wavelength range between 1550 nm and 1560 nm, were embedded horizontally and vertically in the physical model at different levels to monitor deformation at various locations. A leaking pipe was installed to induce the collapse of the formed arch above the cavity. The strain measurements suggest four phases in the sinkhole formation process: (1) cavity formation, (2) progressive weathering and erosion, (3) catastrophic collapse, and (4) subsequent equilibrium conditions. The results showed differences in strain signatures and distributions between horizontal and vertical measurements. During the critical phase of sinkhole collapse, horizontal measurements primarily showed tension, while vertical measurements indicated compression. This investigation demonstrates the effectiveness of FBGs as advanced monitoring tools for sinkhole precursor identification. The study also suggests using FBGs in geotechnical monitoring applications to improve understanding and mitigation of sinkholes and related geohazards.

In the periodic table of the elements, ruthenium is ideally placed, right in the middle, just above iron. And like iron, it possesses several oxidation states, with +2 and +3 being the most common. Accordingly, ruthenium chemistry is extremely rich and well developed, ruthenium complexes show excellent catalytic aptitude, tremendous redox capacity, and intriguing biological activity. However, in the design of sensors, the use of ruthenium complexes remains scarce, despite valuable electro- and photochemical properties. Therefore, there is an opportunity here, and ruthenium-based complexes might become one day, key players in sensing technology. Starting ourselves a new research project with ruthenium-based sensors, writing this review was essential to see the current state of research in the field, to identify opportunities, and to have an overview of state-of-the-art examples.

Structural deformations are one of the most significant factor that affects machine tool (MT) positioning accuracy. These induced errors are complex to be represented by a model, nevertheless they need to be evaluated and predicted in order to increase the machining performance. This paper presents a novel approach to calibrate a machine tool in real-time, analyzing the thermo-mechanical errors through Fibre Bragg Grating (FBG) sensors embedded in the MT frame. The proposed configuration consists of an adaptronic structure of passive materials, Carbon Fibre Reinforced Polymers (CFRP), equipped by FBG sensors that are able to measure in real-time the deformed conditions of the frame. By using a proper thermo-mechanical kinematic model, the displacement of the end effector may be predicted and corrected when it is subjected to external undesired factors. By starting from a set of FE simulations to develop a model able to describe the MT structure stresses, a prototype has been fabricated and tested. The scope was to compare the numerical model with the experimental tests using FBG sensors. The experimental campaign has been performed varying the structure temperature over time and measuring the tool tip point (TTP) positions. The obtained results showed a substantial matching between the real and the predicted position of TTP confirming the effectiveness of the proposed calibration system.

Photonic sensors are innovative devices that leverage the principles of light-matter interaction to enable precise and efficient detection of various physical parameters. These sensors operate by exploiting the interaction between photons, the fundamental particles of light, and matter. The light propagates through an optical waveguide, and a portion of the electromagnetic field extends beyond the waveguide surface, forming the evanescent field. This evanescent field interacts with the surrounding medium, allowing for highly sensitive detection of changes in the refractive index or properties of nearby substances. The underlying concept involves the modulation of light properties, such as intensity, wavelength, or phase, when it interacts with a target substance or undergoes changes in the surrounding environment. The advancements in photonic sensor technology have paved the way for enhanced sensitivity, selectivity, and miniaturization, making them invaluable tools in diverse industries. The ability to harness light-matter interactions for sensing purposes not only facilitates highly sensitive measurements but also allows for non-intrusive and remote monitoring, contributing to the evolution of smart and connected systems. In this overview, the material platforms and waveguide structures are explored that can make highly sensitive photonic devices applied to gas and biosensing applications.

Objective: The aim of this in vitro study was to evaluate the accuracy of resin-based fixed dental restorations, namely veneers, single crowns, and four-unit fixed partial dental prosthesis (FPDs) using two different 3D printers and polymer-based materials. Materials and Methods: A standard maxillary polyurethane jaw model containing prepared teeth was scanned using an intraoral scanner. The generated STL data were used to design the restorations virtually using CAD software. Two 3D printers were utilized for the provisional digital light processing and stereolithography for the castable resin patterns. Each printer produced 10 specimens of each type of restoration, for a total of 80 restorations. The 3d-printed restorations were then 3D scanned using the same intraoral scanner and evaluated for external and internal dimensional accuracy in terms of trueness and precision. A one-way ANOVA and Two-sample T-Test were implemented to compute the precision (variability between groups) and trueness (with the designed CAD model). A level of statistical significance of p-Value

Pedestrian Dead Reckoning (PDR) is a promising algorithm for indoor positioning. However, the accuracy of PDR degrades due to the accumulated error, especially in multi-floor buildings. This paper introduces a three-dimensional (3D) positioning method based on terrain feature matching to reduce the influence of accumulated error in multi-floor scene. The proposed method involves two steps: motion pattern recognition and position matching calibration. The motion pattern recognition aims to detect different motion states, i.e., taking the stairs or horizontal walking, from the streaming data. Then, stair entrances and corridor corners are matched with transition points of motion states and pedestrian turning points, respectively. After matching, calibration is performed to eliminate the accumulated errors. By carrying out experiments on a two-floor closed-loop path with a walking distance about 145 m, it is shown that this method can effectively reduce the accumulated error of PDR , achieving accurate 3D positioning . The average error is reduced from 6.60 m to 1.83 m.

This study presents the design and comprehensive 3D multiphysics simulation of a novel microfluidic immunosensor for real-time, non-invasive monitoring of pro-inflammatory biomarkers in human sweat. The patch-like device, designed using COMSOL Multiphysics, integrates magnetofluidic manipulation with direct-field capacitive sensing. The sensor comprises two distinct units: an immunocomplex enhancement unit, employing a series of microcoils to optimize the binding efficiency, reaction kinetics, and homogeneity of biomarker-magnetic nanoparticle (MNP) interactions, thereby enhancing the sensor's specificity; and a layered capacitive sensing unit, designed to concentrate and detect biomarker-tagged MNPs, thus amplifying sensitivity. Simulations of the capacitive sensing unit revealed a substantial sensitivity increase of up to 42.48\% at an 85\% MNP concentration within the detection zone. These findings highlight the potential of the proposed immunosensor for efficient and precise real-time biomarker monitoring, which may facilitate early disease diagnosis and enable personalized healthcare interventions.

Membrane-based sensors (MePSs) exhibit remarkable precision and sensitivity in detecting pressure changes. MePSs are commonly used to monitor catalytic reactions in solution, generating gas products crucial for signal amplification in bioassays. They also allow catalyst quantification by indirectly measuring the pressure generated by the gaseous products. This is particularly interesting to detect enzymes in biofluids associated with disease onset. To enhance the performance of a MePS, various structural factors influence membrane flexibility and response time, ultimately dictating the device's pressure sensitivity. In this study, we fabricated MePSs using polydimethylsiloxane (PDMS) and investigated how structural modifications affect the Young's modulus (E) and residual stress (σ0) of the membranes. These modifications have a direct impact on the sensors' sensitivity to pressure variations, observed as a function of the volume of the chamber (Σ) or of the mechanical properties of the membrane itself (S). MePSs exhibiting the highest sensitivities were then employed to detect catalyst quantities inducing the dismutation of hydrogen peroxide, producing dioxygen as gaseous product. As a result, catalase enzyme was successfully detected using these optimized MePSs, achieving a remarkable sensitivity of (22.7 ± 1.2) µm/nM and a limit of detection (LoD) of 396 pM.

In mining machines with friction discs, but also in multi-rope traction elevators, it is necessary to distribute the applied tensile load, generated by the weight of the cage and counterweight, evenly in all cross-sections of the load-bearing ropes. Hydraulic devices used for this purpose can operate on the principle of Pascal's law. The article presents a structural design, a 3D model and an implemented solution of a laboratory device capable of simulating a practical method of evenly distributing the total weight of the load into partial tensile forces of the same size acting on a selected number of load-bearing ropes. The laboratory equipment uses two pairs of three steel cables of finite length for the simulations. During the experimental measurements, tensile forces derived from the tractive force of the piston rods, pushed into the bodies of the hydraulic cylinders by the pressure of the hydraulic oil supplied through the pipeline under the pistons of the hydraulic cylinders, were detected. The resulting amount of hydraulic oil pressure in the hydraulic circuit influenced by different values of the hydraulic oil pressures in the hydraulic cylinders and by the pressure in the supply pipe was experimentally studied on the laboratory equipment. Simulations were also carried out in order to detect the hydraulic oil pressure in the hydraulic circuit caused by the change in the different magnitudes of the tensile forces in the ropes From the experiments carried out, it follows that with the appropriate choice of hydraulic elements and the design of the hydraulic circuit, the weight of the load, acting as the total pulling force in the ropes, can be evenly distributed (with a deviation of up to 5%) to all cross-sections of the load-bearing ropes. If the exact values of the hydraulic oil volumes under the pistons of all hydraulic cylinders are not known, it is not possible to calculate the pressure values in the hydraulic circuit when the valves of the hydraulic pipes are gradually opened.

Multi-view stereo (MVS) employs multi-point photography for image point positioning and three-dimensional reconstruction technology. Recently, this technology has been introduced into the monitoring of road slopes due to advances in photography and computing technology. In general, the various phases of post-image processing procedures are applied to various photographic data. In this study a novel, automated image-monitoring system is proposed to improve the ability of automatic processing. First, an Internet of things (IoT)-based digital photography system architecture was constructed to provide automatic control of camera photography and real-time transmission of image data. In addition, a visual SfM-MVS 3D reconstruction technique was used to develop related software and hardware interfaces based on the built-in Python computing framework of Photoscan Pro. The software integrates fully automatic photography, image transmission, monitoring of data processing and product release programs. The experimental results show that the system architecture can be applied to fully automatic three-dimensional monitoring of road slopes.

K-band radar waves have high penetration and low attenuation coefficients. However, the wavelength of this radar wave is relatively short; thus, designing and preparing both broadband and wide-angle radar wave absorbers in this band presents considerable challenges. In this study, a resin-based K-band radar wave absorber with a biomimetic lotus leaf structure was designed and formed by UV curing. Here, microscale lotus leaf papillae and antireflection structures were prepared using a DLP 3D printer, and the contact angle between the material and water droplets was increased from 56° to 130°. In addition, the influence of the geometric parameters of the lotus leaf antireflection structure on the electromagnetic absorption performance and mechanical strength was investigated. After simulation optimization, the maximum electromagnetic loss of the lotus leaf structure 3D printed sample was −32.3 dB, and the electromagnetic loss was below −10 dB in the 20.8–26.5 GHz frequency range. When the radar incidence angle was 60°, the maximum electromagnetic loss was still less than −10 dB. The designed lotus leaf structure has a higher mechanical energy absorption per unit volume (337.22 KJ/m3) and per unit mass (0.55 KJ/Kg) than commonly used honeycomb lightweight structures during the elastic deformation stage, and we expect that the designed structure can be used as an effective lightweight material for K-band radar stealth.

Tailings generated by mining account for the largest proportion of global waste from industrial activities. Copper is relatively uncommon world-wide, with low concentrations in sediments and waters, yet is very elevated around mining sites. On the Keweenaw Peninsula of Michigan, USA, jutting out into Lake Superior, 140 mines extracted native copper from the Portage Lake Volcanic Series, part of an intercontinental rift system. Between 1901-1932, two mills at Gay (Mohawk, Wolverine) sluiced 22.7 million metric tonnes (MMT) of copper-rich tailings (stamp sands) into Grand (Big) Traverse Bay. Here we examine: 1) 3D coastal elevation and reef bathymetry, 2) particle dispersal, 3) copper concentrations and leaching, plus 4) shoreline toxicity. About 10 MMT of tailings created a migrating coastal beach that stretches 7 km from the Gay pile to the Traverse River Seawall. Another 10 MMT are moving underwater on the coastal shelf, threatening Buffalo Reef, an important lake trout and whitefish breeding ground. Aerial photos, ALS (plane) LiDAR, and relatively inexpensive UAS (drone) surveys characterize shoreline structure and aid initial remediation. Because sands (natural beach quartz, stamp sand basalt) are silicates of similar density, particle dispersal is similar and challenging. However, stamp sand beaches contrast greatly with natural sand beaches in both physical profile and chemistry. Dispersing particles retain copper, and release toxic concentrations. Leaching is elevated by exposure to high DOC and low pH waters. Field experiments, shoreline seining, and benthic sampling confirm serious impacts on aquatic biota, supporting tailings removal.