This paper aims to study the performance of solar collectors with various sizes under different weather conditions of different Japanese cities, i.e. Kofu city, Nagoya city and Yamagata city. The heat generated from the solar collector was used to conduct a biogas dry reforming reactor in order to produce H2 to feed a solid oxide fuel cell (SOFC). This study has revealed that the output temperature of solar collector, Tfb in April and July was higher than that in January and October irrespective of city. The optimum length of absorber (dx) of the collector was 4 m irrespective of city. It was clarified that Tfb in Yamagata city in January and October, i.e. winter and autumn is lower than that in Kofu city and Nagoya city especially, which is influenced by the tendency of a solar intensity (I) strongly, not velocity of surrounding air (ua). On the other hand, Tfb is almost the same in April and July, i.e. spring and summer, irrespective of city. The amount of produced H2 from the biogas dry reforming reactor and the power generated by SOFC using H2 in spring and summer were higher compared to the other seasons irrespective of city. This study has revealed that the highest available households number per month was 4.7 according to the investigation in this study.

This study focuses on a biogas dry reforming to produce H2. Biogas contains CO2 of 40 vol% approximately, indicating that the efficiency of the power generation is reduced because of the smaller heating value compared with a natural gas. The authors have proposed the combination system consisting of biogas dry reforming reactor and solid oxide fuel cell (SOFC). Since a biogas dry reforming is an endothermic reaction, this study adopts a membrane reactor which can be operated by causing the non-equilibrium state with H2 separation from the reaction space. This study aims to clarify the impact of thickness of Pd/Cu membrane on the characteristics of the biogas dry reforming membrane reactor using Pd/Cu membrane and Ni/Cr catalyst. The impact of the operation temperature, the molar ratio of CH4:CO2 and the differential pressure between the reaction chamber and the sweep chamber on the characteristics of the biogas dry reforming membrane reactor using Pd/Cu membrane and Ni/Cr catalyst is examined changing the thickness of Pd/Cu membrane. As a result, the highest concentration of H2 is 122711 ppmV which is obtained in case of CH4:CO2 =1:1 at the reaction temperature of 600 ℃ and the differential pressure of 0 MPa using the Pd/Cu membrane whose thickness of 40 m.

This study proposed the combination system consisting of biogas dry reforming reactor and solid oxide fuel cell (SOFC). Since a biogas dry reforming is an endothermic reaction, this study adopted a membrane reactor operated due to the non-equilibrium state with H2 separation from the reaction space. This study aimed to clarify the characteristics of Ni/Cr/Ru catalyst using for a biogas dry reforming membrane reactor. Additionally, this study also investigated the comparison of the characteristics of Ni/Cr/Ru catalyst with that of Ni/Cr catalyst. The impact of operation temperature, the molar ratio of CH4 : CO2, the differential pressure between the reaction chamber and the sweep chamber and the introduction of sweep gas on the characteristics of the biogas dry reforming membrane reactor using Pd/Cu membrane and Ni/Cr/Ru catalyst was examined. The concentration of H2 using Ni/Cr/Ru catalyst was larger than that using Ni/Cr catalyst by 2871 ppmV for the molar ratio of CH4 : CO2 = 1.5 : 1 at the reaction temperature of 600 ℃ and the differential pressure of 0 MPa without a sweep gas, especially. Under this condition, CH4 conversion, H2 yield and thermal efficiency were 67.4 %, 1.77×10-2 % and 0.241 %, respectively.

This work is devoted to the study of active and stable nickel catalysts for methane dry reforming based on Pr-doped ceria-zirconia obtained by solvothermal continuous method. The studies of physicochemical and catalytic properties of the 5%Ni\Ce0.75Zr0.25-xPrxO2 series showed that Pr introduction leads to an increase in the amount of highly reactive oxygen of the oxide lattice. Praseodymium-based catalysts showed significantly higher reactant conversions. In addition to the nature of support, the method of nickel introduction was also studied - Ni was added both by impregnation and one-pot with mixed oxide preparation. The method of Ni addition was shown to have significant effect on the morphology of the supported active component and, respectively, on the catalytic activity. The 5%Ni/Ce0.75Zr0.15Pr0.1O2 catalyst prepared by one-pot method showed stable operation in the MDR reaction for 30 hours at CO2 and CH4 conversions of ~40% and an H2 yield of ~18% (Т=700°С, τ=10ms).

In this study, vermiculite was explored as a support material for nickel catalysts in two key processes in syngas production through dry reforming of methane with CO2 and steam reforming of ethanol. The vermiculite was subjected to acid or base treatment, then, Ni catalysts were prepared through incipient wetness impregnation and characterized using various techniques, including X-ray, FTIR, temperature programmed reduction (H2-TPR). TG-TD analyses were performed to assess the formation of carbon deposits on spent catalysts. The Ni based catalysts were used in the reaction tests without a reduction pre-treatment. Initially, raw vermiculite-supported nickel showed limited catalytic activity, however after acid (Ni/VTA) or base (Ni/VTB) treatment, vermiculite became an effective support for nickel in dry methane reforming. The resulting catalysts (Ni/VTB and Ni/VTA) displayed outstanding performance, with high methane conversion and hydrogen yield. Acidic treatment improved the reduction of nickel species and reduced carbon deposition, outperforming alkali treatment. The prepared catalysts were also explored in ethanol steam reforming. The performance was investigated as a function of the temperature, water/ethanol ratio, and space velocity, with acid-treated catalysts performing as the best. The study emphasized the importance of contact time with the catalyst and addressed challenges related to carbon formation and sintering for long-term stability. In conclusion, acidic treatment of the vermiculite support, before Ni deposition, significantly enhanced the catalytic activity and stability of nickel catalysts in both dry methane reforming and ethanol steam reforming processes.

This study investigated dry reforming of methane with combined catalysts supported on γ-Al2O3 support doped with 3.0 wt. % TiO2. The physicochemical properties of all the catalysts were determined by inductively-coupled plasma/mass spectrometry metal analysis, nitrogen physisorption, X-ray diffraction, temperature programmed reduction/desorption, thermogravimetric analysis, and scanning electron microscopy. The addition of CeO2 and MgO to Ni strengthened the interaction between the Ni and the support. The catalytic activity results indicated that the CeO2 and MgO addition to Ni did not do much in retarding carbon deposition, but they improved the activity of the catalysts. Among the tested catalysts, it was found that the catalyst with the composition of 5.0 wt % NiO-10.0 wt % CeO2/3.0 wt %TiO2-γ-Al2O3 resulted in the highest CH4 and CO2 conversion with H2/CO mole ratio close to unity. The optimum reaction conditions in terms of reactant conversion and H2/CO mole ratio were achieved by varying space velocity and CO2/CH4 mole ratio.

The effect of H2S with high concentrations on catalytic dry reforming of methane (DRM) process has seldom been focused on previously. Herein, a thermodynamic analysis of the DRM reactions in the presence of H2S with the concentration varying in 0-20 vol% was conducted firstly. Several typical types of catalysts including MgO, NiO/MgO and LaNiO3 in different states were prepared for executing DRM at 800 C, 0.1 MPa in the feed of 20 vol% CO2 and 20 vol% CH4 balanced with N2. The catalytic performance of each catalyst for DRM process under conditions of absence and presence of H2S was compared. A promotion effect of increasing H2S concentration on both the conversions of CO2 and CH4 and the molar yields of CO and H2 was observed on all the catalysts especially the MgO and the pristine NiO/MgO. While a significant decline in catalytic activity of either the reduced NiO/MgO or the reduced LaNiO3 catalyst after adding H2S, moderate reactant conversions still sustained. The results of process analysis and catalyst structure characterization suggest that H2S participation can contribute to the increment in CO2 and CH4 conversion, and active S-adsorbed species may play the key role of catalysis in the reactions involving H2S.

Conventional hydrogen production, as an alternative energy resource, has relied on fossil fuels to produce hydrogen, releasing CO2 into the atmosphere. Hydrogen production via the dry forming of methane (DRM) process is a lucrative solution to utilize greenhouse gases, such as carbon dioxide and methane, by using them as raw materials in the DRM process. However, there are a few DRM processing issues, with one being the need to operate at a high temperature to gain high conversion of hydrogen, which is energy intensive. In this study, bagasse ash, which contains a high percentage of silicon dioxide, was designed and modified for catalytic support. Modification of silicon dioxide from bagasse ash was utilized as a waste material and the performance was explored of bagasse ash-derived catalysts interacting with light irradiation and reducing the amount of energy used in the DRM process. The results showed that the performance of 3%Ni/SiO2 bagasse ash WI was higher than that of 3%Ni/SiO2 commercial SiO2 in terms of the hydrogen product yield, with hydrogen generation initiated in the reaction at 300 °C. Using the same synthesis method, the current results suggested that bagasse ash-derived catalysts had better performance than commercial SiO2-derived catalysts when exposed to an Hg-Xe lamp. This indicated that silicon dioxide from bagasse ash as a catalyst support could help improve the hydrogen yield while lowering the temperature in the DRM reaction, resulting in less energy consumption in hydrogen production.

In this research, catalytic steam reforming acetic acid derived from the aqueous portion of bio-oil for hydrogen production was investigated by using different Ni/ATC (Attapulgite Clay) catalysts prepared by precipitation, impregnation and mechanical blending methods. The fresh and reduced catalysts were characterized by XRD, N₂ adsorption-desorption, TEM and H₂-TPR. The comprehensive results demonstrated that the interaction between active metallic Ni and ATC carrier was significantly improved in Ni/ATC catalyst prepared by precipitation method, and in which the mean Ni particle size was the smallest (~13 nm) resulted in the highest metal dispersion (7.5%). The catalytic performance of the three catalysts was evaluated through the process of steam reforming of acetic acid in a fixed-bed reactor under atmospheric pressure at two different temperatures, such as 550 ℃ and 650 ℃. Results showed that the Ni/ATC (PM-N/ATC) prepared by precipitation method, achieved the highest H₂ yield of ~82% and little lower acetic acid conversion efficiency of ~85% than that (~95%) of Ni/ATC (IM-NATC) prepared by impregnation method. In addition, the deactivation catalysts after reaction for 4 h were analyzed by XRD, TGA-DTG and TEM, which demonstrated that the catalyst deactivation was not caused by the amount of carbon deposition, but owed to the significant agglomeration and sintering of Ni particles in the carrier.

The aim of this study is to present the spatial and temporal variability of the frequency of dry and wet days and dry and wet spells against the background of changes in precipitation and atmospheric circulation. The study is based on daily precipitation totals from 46 meteorological stations in Poland for the years 1966-2023. Additionally seven circulation indices were used: GBI, NAO, AO, EA, EA/WR. SCAND ana AMO. Dry days are defined as days without precipitation. Wet days are days with at least 1 mm of precipitation. It was shown that dry spells are much more common that wet spells, are longer and cover larger areas. Long term changes in annual characteristics of dry and wet days and spells are statistically insignificant. Only the length of the longest dry spell in the year increases. However, there are significant changes in their annual cycles. Spring is drier, in summer months, precipitation decreases in the south and increases in the north, November and December, symbols of gloomy rainy weather, are increasingly drier, rainy weather moved to January and February. The impact of circulation varies with seasons and NAO, Ao, SCAN and GBI indices have the strongest impact.

As the global demand for renewable energy continues to rise, biogas technology has emerged as a promising solution for sustainable energy generation. This review article presents the advantages of biogas technologies and extensively discusses the main principles of biogas production in the methane fermentation process. In this respect, the main parameters of the process, which require monitoring and are at the same time decisive for its course and efficiency are described, the principles of substrate selection are discussed and the necessity and advantages of the use of organic waste according to the model of a circular economy and the concept of sustainable development, are indicated. The part on biogas production is summarised with an explanation of the necessity to treat and purify biogas, taking into account the share of methane extracted. A special place in this paper is devoted to the design, construction, functioning and operation of biogas plants, based on both scientific and practical aspects. In conclusion of this chapter, the economic aspects and profitability of operating biogas plants are discussed, taking into account, in a theoretical balance sheet – in addition to investment and operating costs and the availability and cost of raw materials – the possibilities of producing and using electricity and heat, as well as environmental and social benefits. The article concludes with a discussion of opportunities and barriers to the development of biogas plants, pointing to: financial issues, access to feedstock, political regulations, public awareness and the geopolitical situation as key factors issues related to biogas plants – in different regions of the world.

Wildfires have always been a part of the history of Mediterranean forests. However, forest regeneration after a wildfire is not certain. It depends on many factors, some of which may be influenced by land management activities. Failure of regeneration will cause a regime shift in the ecosystem, reducing the provision of ecosystem services and ultimately leading to desertification. How can we increase Mediterranean forests’ resilience to fire? To answer this question, we did a literature review, investigating chains of processes that allow forests to regenerate (which we label “regeneration mechanisms”), and assessed the impact of selected management practices documented in the WOCAT database on the regeneration mechanisms. We identified three distinct regeneration mechanisms that enable Mediterranean forests to recover, as well as the time frame before and after a fire in which they are at work, and factors that can hinder or support resilience. The three regeneration mechanisms enabling a forest to regenerate after a fire consist of regeneration (1) from a seed bank; (2) from resprouting individuals; and (3) from unburned plants that escaped the fire. Management practices were grouped into four categories: (1) fuel breaks, (2) fuel management, (3) afforestation, and (4) mulching. We assessed how and under what conditions land management modifies the ecosystem’s resilience. The results show that land management influences resilience by interacting with resilience mechanisms before and after the fire, and not just by modifying the fire regime. Our analysis demonstrates a need for adaptive – i.e. context- and time-specific – management strategies.

Biogas production from organic waste is a promising renewable energy source, but achieving optimal production and digester stability can be challenging. This study investigated the impact of the Evogen microbial additive on biogas production and digester quality through microbial abundance and physicochemical parameter analysis. Two biogas plants, BG01 and BG02, were examined using 16S rRNA profiling to assess microbial abundance. Simultaneously, physicochemical parameters, including FOS/TAC ratio, total solids, volatile solids, biogas production, and VFA profile, were measured to evaluate digester performance. Results revealed distinct microbial community shifts in Evogen-treated digesters. Increased abundance of methanogenic archaea and hydrolytic bacteria indicated improved anaerobic digestion. Evogen supplementation also positively affected digester performance, with higher FOS/TAC ratios indicating enhanced acidification and methanogenesis. Reductions in total solids and volatile solids demonstrated improved organic matter degradation. Significantly higher biogas production was observed in Evogen-treated digesters, highlighting its potential as a microbial additive. Furthermore, VFA profiling demonstrated improved process stability and reduced substrate inhibition in Evogen-treated digesters. In summary, Evogen microbial additive positively influenced microbial dynamics, improving biogas production and digester quality. These findings contribute to optimizing biogas production systems and understanding the complex microbial interactions within anaerobic digesters.

Berberis vulgaris (L.) has remarkable ethnopharmacological properties and is widely used in traditional medicine. The present study investigates B. vulgaris stem bark (Berberidis cortex) by extraction with 50% ethanol. The main secondary metabolites were quantified, resulting in a polyphenols content of 17.6780 ± 3.9320 mg Eq Tannic acid / 100 g extract, phenolic acids amount of 3.3886 ± 0.3481 mg Eq Chlorogenic acid / 100 g extract and 78.95 µg/g berberine. The dried hydro-ethanolic extract (BVE) was thoroughly analyzed using Ultra-High Performance Liquid Chromatography coupled with High-Resolution Mass Spectrometry (UHPLC–HRMS/MS) and HPLC and 40 bioactive phenolic constituents were identified. Then, the antioxidant potential of BVE was evaluated using three methods; our results could explain the protective effects of Berberidis cortex EC50FRAP = 0.1398 mg/mL, IC50ABTS = 0.0442 mg/mL, IC50DPPH = 0.2610 mg/mL compared to ascorbic acid (IC50 = 0.0165 mg/mL). Next, the acute toxicity and teratogenicity of BVE and Berberine - Berberine sulfate hydrate (BS) - investigated on Daphnia sp reported significant BS toxicity after 24 h; BVE revealed considerable toxicity after 48 hours and induced embryonic developmental delays. Finally, the anticancer effects of BVE and BS were evaluated on different tumor cell lines after 24 and 48 hours of treatments. The MTS assay evidenced a dose- and time-dependent antiproliferative activity, higher on BS than BVE. The strongest diminution of tumor cell viability was recorded on breast (MDA-MB-231), colon (LoVo) cancer, and OSCC (PE/CA-PJ49) cell lines after 48 h of exposure (IC50 < 100 µg/mL). However, no cytotoxicity was reported on normal epithelial cells (HUVEC) and hepatocellular carcinoma (HT-29) cell lines. Extensive data analysis supports our results, showing a significant correlation between the BVE's concentration, phenolic compounds content, antioxidant activity, exposure time, and the viability rate of various normal cells and cancer cell lines.

The present study analyzed the effect of temperature, pH, retention time, pretreatment and mixing ratio on the anerobic digestion process. The parameters during the anaerobic co digestion of cow manure and food waste were then optimized using the Taguchi experimental design method. ANOVA is carried out to find the significant parameters which influence the biogas production. Experimental tests were carried out at laboratory scale reactors kept at different temperatures (28 °C, 35 °C, and 50 °C). The specific methanogenic Performance (SMP) during anerobic digestion at higher temperatures was characterized with the analysis of acetate, propionate, butyrate, hydrogen, glucose, and formate. The improvement of biogas production with different pre-treatment i.e., ultrasonic, autoclave, and microwave techniques also analysed. The results showed that reactor that maintained at 35 °C showed the highest biogas production. While the reactor that maintained at lower temperature (28 °C) produced the lower volume of biogas. As the retention time increases, the amount of biogas produced increases. Methanogenic activities of microorganisms reduced at higher temperature conditions (65 °C). Biogas production increased by 28.1%, 20.23%, and 13.27 % when the of substrates treated with ultrasonic, autoclave, and microwave, respectively, compared to the untreated substrate. The optimized condition for the highest biogas production during anaerobic co digestion of food waste and cow manure is temperature of 35 °C, pH of 7 and mixing ratio (CM: FW=1.5:0.5). ANOVA showed that temperature is the most important input parameter affecting biogas production, followed by mixing ratio.

There is a need to find methods to intensify the anaerobic digestion process. One possibility is the use of pre-treatment techniques. Many laboratory tests confirm their effectiveness, but in most cases, there is no verification work carried out on industrial plants. The aim of the research carried out under laboratory conditions and on a large scale was to determine the technological and energy efficiency of the use of hydrodynamic cavitation in the pre-treatment of a waste mixture from dairy farms. It has been shown that hydrodynamic cavitation significantly increases the concentration of organic compounds in the dissolved phase. In the most effective variants, the increase in the content of these indicators was over 90% for both COD and TOC. The degree of solubilisation achieved was 49±2.6% for COD and almost 52±4.4% for TOC. Under laboratory conditions, the highest effects of anaerobic digestion were achieved after 10 minutes of pre-treatment. The amount of biogas was on average 367±18 mL/gCOD and the amount of methane 233±13 mL/gCOD. Further large-scale optimisation trials showed that after 8 minutes of hydrodynamic cavitation, the biogas yield was 327±8 L/kgCOD with a CH4 content of 62.9±1.9%. With this variant, the net energy yield was 66.4±2.6 kWh/day, a value that was 13.9% higher than the original variant with 10 minutes of disintegration and 3.1% higher than the variant without pre-treatment.

This paper explores the emergence of Sustainability-Linked Bonds (SLBs) as an innovative instrument to finance sustainability objectives. SLBs have emerged as a transformative financial instrument, establishing an explicit link between cost of funding and sustainability objectives. SLBs were first launched in 2019 and represent 7% of labelled bonds, still dominated by the more established green bonds. Issuance of SLBs now exceeds $250 billion. Following initial enthusiasm, they are now facing criticism. In the context of the growth of sustainable finance and concerns of greenwashing, this paper investigates ways to enhance the design of SLBs. Drawing on literature and expert interviews, the findings highlight the strong potential of SLBs to contribute to sustainability financing, especially in hard-to-abate sectors. The paper identifies the key positive attributes of SLBs and their limitations in five areas: key performance indicators’ (KPI) selection, sustainability performance targets’ (SPT) calibration, bond characteristics, reporting practices, and resource requirements. Recommendations to financial intermediaries, issuers and policy makers include defining standardized KPIs based on a materiality assessment, requesting SPTs to be supported by science and in line with an issuer’s core strategy, tailored step-up mechanisms and avoidance of call loopholes, and stricter reporting. SLBs represent an opportunity to add rigor to sustainable finance and better price externalities, where material topics have an explicit impact on cost of funding and credit ratings.

Keywords: glycerin; Ni-based catalyst; lanthanum; semi-industrial scale; hydrogen production; biorefinery; monitoring.

A new study for CH4 reforming to hydrogen and hydrogen storage was performed using magnesium-based alloy. MgH2-12Ni (with the composition of 88 wt% MgH2 + 12 wt% Ni) was prepared in a planetary ball mill by milling in hydrogen atmosphere (reaction-involved milling). X-ray diffraction (XRD) analyses were performed for the samples after reaction-involved milling and after reactions with CH4. The variation of adsorbed or desorbed gas with time was measured by a Sieverts’ type high-pressure apparatus at 773 K. The microstructures of the powders were observed using scanning transmission microscope (STEM) with energy-dispersive X-ray spectroscopy (EDS). The synthesized samples were also characterized using Fourier Transform Infrared (FT-IR) spectroscopy. XRD pattern of MgH2-12Ni after reaction with CH4 of 12 bar at 773 K and decomposition under 1.0 bar at 773 K exhibited phases of MgH2 and Mg2NiH4. This shows that reforming of CH4 was occurred, hydrogen produced after reforming of CH4 was then adsorbed on the particles, and hydrides were formed during cooling to room temperature. Ni and Mg2Ni formed during heating up to 773 K are believed to have brought about catalytic effects for reforming CH4. MgH2-12Ni adsorbed 0.8 wt% reformed CH4 within 1 min in a reaction with CH4 of 12 bar at 773 K and then desorbed 0.8 wt% reformed CH4 (hydrogen-containing mixture) within 1 min under 1 bar at 773 K. Attenuated total reflectance FT-IR spectroscopy (ATR-FTIR) spectra of MgH2-12Ni after reactions under 12 bar CH4 at 723 K and 773 K showed peaks of C-H bending, C=C stretching, O-H stretching, O-H bending, and C-O stretching.

This study assesses the biomethane (CH4) generation and greenhouse gas (GHG) emissions resulting from municipal solid waste landfilling in Phnom Penh, Cambodia, with a focus on the impact of fugitive CH4 emissions and operation processes in four landfilling scenarios: simple dumping (S1), improved management with leachate treatment (S2), engineered landfill with flaring (S3), and engineered landfill with energy recovery (S4). The study also considered the environmental benefits of carbon sequestration and landfill gas utilization. The LandGEM and IPCC FOD models were used to calculate CH4 generation over the period of 2009-2022, and it was found that approximately 18 and 21 M kg/year of CH4 are released, respectively. The energy potential from CH4 recovery was 51–61 GWh/year. Overall GHG emissions in S2 were the highest, amounting to 409–509 M kg CO2-eq/year, while S1 had lower emissions at 397–496 M kg CO2-eq/year. Flaring captured CH4 in S3 could reduce GHG emissions by at least 55%, and using captured CH4 for electricity production in S4 could mitigate at least 83% of GHG emissions. Electricity recovery (S4) could avoid significant amounts of GHG emissions (˗104.5 kg CO2-eq/tMSW). The study suggests that landfill gas-to-energy could significantly reduce GHG emissions.

The decline of fossil fuels, the increase of greenhouse gases and the global demand for energy are driving the search for alternative energy sources. Anaerobic digestion is a promising technology because it can convert organic biomass into biogas. As the climate warms, there is an increase in biomass of plant origin in water bodies, and ecosystems are unable to clean themselves. This work aims to show that macroalgae and aquatic plants can be an excellent raw material for biogas production. By mixing them with co-substrates such as cattle manure, higher biogas and methane yields can be obtained. When Cladophora glomerata and Zostera marina macroalgae are mixed with cattle manure, the biogas yield is up to 458.8 mL/gVS and 397.9 mL/gVS, respectively. Methane concentration remained high and reached 62.4%–64.1%. The obtained research results show the high energy value of biogas and the energy potential of biomass. Macroalgae increased the energy potential of biogas to 22.9 MJ/m3, and the energy potential of biomass reached 2.40 MJ/Kg. Due to its high energy value, biogas produced from the considered substrates can be an excellent alter-native to fossil fuels. Integrating aquatic macroalgae into anaerobic digestion is a promising approach for a waste-free marine and freshwater system.

This study involved a comprehensive examination of sensory attributes in Bísaro dry-cured loins, including odor, androsterone, scatol, color, fat color, hardness, juiciness, chewiness, flavor intensity, and flavor persistence. Analysis of 40 samples revealed a wide variation in these attributes, ensuring a robust margin for multivariate calibration purposes. The respective near-infrared (NIR) spectra unveil distinct peaks associated with significant components such as protein, lipid, and water. Support Vector Regression (SVR) models were methodically calibrated for all sensory attributes, with optimal results using multiplicative scattering correction pre-treatment, MinMax normalization, and radial base kernel (non-linear SVR model). The predictive models exhibited acceptable results, characterized by R-squared values close to 1 (0.9616 - 0.9955) and low RMSE values (0.0400 – 0.1031). The prediction set's relative standard deviation (RSD) remained under 5%. Comparisons with prior research revealed significant improvements in prediction accuracy, particularly when considering attributes like pig aroma, hardness, fat color, and flavor intensity. This research underscores the potential of advanced analytical techniques to improve the precision of sensory evaluations in food quality assessment.

The world is facing a serious energy crisis and environmental pollution problems due to a sharp increase in the world population. Bioenergy is an eminent solution to these problems. Anaerobic digestion is a green energy technology used worldwide for the conversion of organic waste to biogas. It is reported that organic wastes are hard to digest and need some technical improvement in the anaerobic digestion process to improve biogas yield. Iron-based additives, due to their electron acceptance and donation capabilities, have been emphasized as being exceptional in improving anaerobic digestion process efficiency amongst all other enhancement options. This study reviews the major available types of iron-based additives, their characteristics, and their preparation methods. The preferred iron-based additive that has a significant effect on the enhancement of biogas yield is also discussed. The use of iron-based additives in the anaerobic digestion process with varying dosages and their impact on the biogas generation rate is also being studied. Substrates, operating parameters, and types of anaerobic digesters used in recent studies while researching the effects of iron-based additives are also part of this review. Lastly, this study also confirms that iron-based additives have a significant effect on the reduction rate of the volatile suspended solids, methane content, biogas yield, and volatile fatty acids.

The aim of the study was to examine the biogas and methane yield of maize silage, a wastes in agricultural point of view and compare it to the biogas productivity of commonly used mixture of maize silage and mixed fodder with water. The experimental study was carried out into 2 parts. Firstly, the batch experiment was conducted in Mesophilic conditions (35°C), at five different hydraulic retention times (HRT): 6 DAT, 11 DAT 20 DAT 29 DAT and 41 DAT. The results revealed that maize silage was generated the highest biogas yield of 537 mL /241 mL at the HRT of 6days /41 days. Mixed fodder produced the highest biogas yield of 421 mL at the HRT of 6th days and the lowest one was 252 mL at the HRT of 20th days. Finally, the methane, carbon dioxide and hydrogen sulphide of biogas produced from maize silage and mixed fodder were analyzed using a gas chromatography. The results shown that biogas from maize silage precedes the gas less than the mixed fodder. In the field level experiment proved that from mixed fodder produced gas which would be enough for 7 member’s family used 3 months for the purpose of their cooking.

The focus of our study was the changes in the composition of semi-natural dry grasslands in Hungary. Since these valuable habitats were created with the help of humans, their preservation also requires regular treatment. Our mowing experiment aimed to investigate the suppression of the native Calamagrostis epigejos L. Roth. In Hungary, in the Cserhát Mountains, eight permanent plots were mowed twice a year. The vegetation was sampled annually between 2001 and 2011. The effects of mowing were investigated with repeated measures analysis of variance (ANOVA). After 10 years, the C. epigejos cover of the mowed plots decreased significantly, from the initial average of 62.38 to 7.50%. Surprisingly, we also experienced a similar decrease in the control plots. Regular treatment also had a positive effect on the number of species and diversity. Species richness increased continuously in both treatment types, which indicates the combined effect of vegetation succession and treatment. The biomass growth of other Poaceae and Fabaceae species, which are important from a grassland management perspective, was also facilitated by mowing. Our results suggest that long-term in situ experiments and continuous botanical studies are needed to establish a reliable utilization of grasslands.

Polyelectrolyte-drug complexes are interesting alternatives to improve unfavourable drugs properties. Vancomycin (VAN) is an antimicrobial used in the treatment of methicillin-resistant Staphylococcus aureus pulmonary infections in patients with cystic fibrosis. It is generally administered intravenously with high incidence of adverse side effects, which could be reduced by intrapulmonary administration. Currently, there are no commercially available inhalable formulations containing VAN. Thus, the present work focuses on the preparation and characterization of an ionic complex between hyaluronic acid (HA) and VAN with potential use as inhalable formulations. Particulate-solid HA-VAN25 complex by spray drying from an aqueous dispersion was obtained. FTIR spectroscopy and thermal analysis confirmed the ionic interaction between HA and VAN, while an amorphous diffraction pattern by X-ray was observed. The powder density, geometric size and morphology showed a suitable aerosolization and aerodynamic performance of the powder, indicating the capability of reaching the deep lung. An in vitro extended-release profile of VAN from the complex was obtained, exceeding 24 hours. Microbiological assays against methicillin-resistant and -sensitive reference strains of Staphylococcus aureus, showed that VAN preserves its antibacterial efficacy. In conclusion, HA-VAN25 exhibited interesting properties for the development of inhalable formulations with potential efficacy and safety advantages over conventional treatment.

The objective of this study is to design an optimal model predictive control (MPC) strategy using manipulated variables to control the production of a sufficient amount of hydrogen through low temperature autothermal reforming of dimethyl ether (DME), a reforming reaction performed using PdO/ZnO/γ-Al2O3 catalysts coated on honeycomb cordierite ceramics. Experiments and simulation have verified that the optimal activity temperature of the catalyst is 400 °C, and the hydrogen volume fraction in syngas is over 43%. In the implementation of the hydrogen production system, the MPC controller can precisely determine the feed rates of DME, high-purity air, and water based on the space state equation of the reformer, to achieve the anti-disturbance of the reformer temperature. Thus, the reduction of hydrogen yield and sintering of the catalyst as a result of overheating are prevented. As the static and dynamic performance of hydrogen production exhibits excellent tracking of the setpoints, an autonomous, automated, and reliable continuous system was designed to meet the desired hydrogen demand situation. This study shows that an autonomous, automated, and reliable continuous hydrogen production reforming system can be designed to actively respond to the on-board hydrogen usage situation.

This work focuses on the support effect on the performances of Co-based catalysts for the acetic acid steam reforming. SBA-15, a well ordered hexagonal mesoporous silica structure, and CeO2 have been selected as the supports, with the impact of chromium addition also being investigated. Better acetic acid steam reforming performances have been recorded for CeO2 compared to SBA-15 supported catalysts and, in particular, the 7Co/CeO2 catalyst showed the highest values of acetic acid conversions with enhanced H2 yields below 480°C, in comparison to the other investigated catalytic formulations. In addition, more pronounced coke depositions and acetone concentrations have been obtained with CeO2 supported catalysts, due to the tendency of ceria to catalyse the ketonization reaction. Chromium addition to Co/SBA-15 catalysts led to an enhancement in the activity towards acetic acid steam reforming, while on CeO2 supported catalysts no improvement in the catalysts activity was observed; however, on both SBA-15 and CeO2 supported catalysts, Cr addition reduced the amount of coke deposited on the catalysts surface.

The abrupt increase of the electric vehicles in Bangladesh needs huge amount of power. As a result, alternative energy sources are emphasized due to limited fossil fuels in order to develop a sustainable energy sector with environment friendly resources. Bangladesh has an enormous potential in the field of renewable resources like biogas and biomass. This paper presents 20 kW electric vehicle charging station (EVCS) utilizing biogas resources where maximum energy requirement is 100 kWh. In this paper, the biogas based EVCS is designed using MATLAB Simulink and HOMER software. Daily 15-20 electric vehicles can be recharged their batteries using the proposed charging station. The proposed system offers lower cost of energy compared to the grid electricity. Moreover, the proposed charging station shows 68.75% reduction in CO₂ emission than grid based charging station. In addition, the proposed EVCS will save monthly $ 16.25 and $ 27.50 respectively for easy bike and auto rickshaw type electric vehicles in Bangladesh.

Beef dry aging consist in a selection of unpackaged primal cuts that are placed in a refrigerator room with controlled environment for several weeks. The goals are the concentration of flavor, like nutty and beefy and tenderness improvement. In this study it was intended verify the microbiological and physicochemical behavior and the meat sensorial perception during a process example of meat dry aging. Twelve beef loins were selected for 90 days of dry aging and placed in a refrigerator room with average temperature, relative humidity and forced air 3.17 ± 0.68 °C, 60.65 ± 4.23 % and 0.5-2 m/s, respectively. On 1, 14, 21, 35, 60 and 90 days of dry aging, were taken two samples, crust and lean meat for microbiological counts, pH, aw, color L*a*b* and sensorial analysis. During drying, there weren´t any pathogenic bacteria counts and the average counts were higher for the crust. The aw and pH had an average of 0.98 ± 0.02 and 5.77± 0.015, with a slightly decrease and increase respectively (P<0.05) along aging days. The dry aging process practices, with room refrigeration at RH<65.00% and temperature <4.00 °C can be the reason for aw<0.98 and meat pH<6.00 and therefore for the absence of pathogenic bacteria. The lower microbial counts on the lean meat and the overall acceptability assessed by the sensory panel confirm the importance of the good trimming and storage practices for the dry aged beef.

The dry washing method is an alternative to replace water washing, thereby reducing the negative impacts of contamination. However, commercial adsorbents come from industrial processes that, due to their composition, may not be such a sustainable resource in the global biodiesel production process. In this study, the use of organic residues, such as sawdust, coconut fiber, nutshell, rice husk and water hyacinth fiber, were proposed as bioadsorbents for the purification of biodiesel from waste cooking oil (WCO). Quality parameters such as the acid value, water content, and free and total glycerin content were evaluated and compared with those of commercial resins such as Magnesol® and Amberlite™. Promising results were obtained using sawdust during the purification process, achieving a 31.6% reduction in the acid value compared to that of unpurified biodiesel, the reduction was 31.3% more efficient than Amberlite™. Sawdust adsorbed free glycerin at 55.8%, being more efficient than Amberlite™. The total glycerin values were similar between commercial resins and sawdust. A water content values were similar than Amberlite™ and better than that with Magnesol®, at 4.3% and 39.81%, respectively. These results show that sawdust can be used as an alternative bioadsorbent in a dry purification method for biodiesel being a residue with less environmental impact.

This study investigated whether biogas reactor performance, including microbial community development, in response to a change in substrate composition is influenced by initial inoculum source. Test reactors were first started with two different inocula and operated with the same grass-manure mixture for more than 120 days. These reactors initially showed great differences depending on inoculum source, but eventually showed similar performance and overall microbial community structure. At the start of the present experiment, the substrate was complemented with milled feed wheat, added all at once or divided into two portions. The starting hypothesis was that process performance depends on initial inoculum source and microbial diversity, and thus that reactor performance is influenced by the feeding regime. In response to the substrate change, all reactors showed increases and decreases in volumetric and specific methane production, respectively. However, specific methane yield and development of the microbial community showed differences related to initial inoculum source, confirming the hypothesis. The different feeding strategies had however only minor effects on process performance and overall community structure, but still induced differences in the cellulose-degrading community and in cellulose degradation.

Demand for environmentally friendly types of energy is growing all over the world, which naturally increases the intensity of work on the production of hydrogen-containing fuel mixtures. Steam reforming of methanol is one of the most effective areas of research, as it is a process with low energy consumption. The results of steam reforming of methanol on the catalysts prepared by solution combustion synthesis (SCS) and impregnation by moisture capacity are presented. Investigation of the activity of Cu-Ce-Al catalysts of different composition was carried out for production of hydrogen and comparison of SCS with traditional impregnation method. Methanol conversion reaches 99%, while the selectivity of H2 was 88%, at 500 °C. It was found that CuAl2O4 spinel formation is due to substitution of Al3+ with Cu2+ Ce3+ cations. A consequence CuAl2O4 and CeAlO3 lattice parameters increase because of difference in ionic radius of Al3+ (0.53 Å) and Cu2+ (0.73 Å), Ce3+ (1.07 Å). Advantages of SCS catalysts in steam reforming of methanol were shown. The aim of this research is to develop a new catalyst for conversion of methanol into hydrogen containing fuel mixtures, which will further promote the organization of a new era of environmentally friendly energy-saving production methods.

CONTEXT– Energy is widely involved in human activity and corresponding emissions of SOX, NOX and CO2 from energy generation processes affect global climate change. Clean fuels are desired by society because of their reduced greenhouse gas emissions. Hydrogen is once such candidate fuel. Much hydrogen is produced from fossil fuel, with biomass being an alternative process. OBJECTIVE– The project compared the environmental impact of hydrogen production by natural gas steam reforming vs. biomass gasification. METHOD–Environmental impact was calculated from the input and output data from life cycle inventory analysis. The impact assessment was focused on greenhouse gas emission, acidification, and eutrophication. Models of the two processes were developed and analysed in OpenLCA. The agribalyse database was used to connect inventory flow data to environmental impacts. FINDINGS– For all three metrics, biomass gasification had lower impacts than natural gas steam reforming, sometimes by large margins. For biomass gasification the silica sand production contributes most to all three impact categories, whereas for natural gas steam reforming it is the LPG extraction.

To achieve higher crop yields and maintain environmental conservation, it becomes imperative to adopt novel agricultural methods that improve both the quantity and quality of produce. The above study focused on investigating the effectiveness of integrated use of biogas slurry (BS) and inorganic nutrigation on spinach growth and nutrient uptake through drip irrigation. Under field conditions and using a split plot design, spinach was cultivated with seven different treatments: biogas slurry nutrigation (BSN) (T1), integrated inorganic + organic nutrigation: 40% Recommended dose of fertilizer (RDF) +BSN (T2), 60% RDF +BSN (T3), 80% RDF +BSN(T4), 100% RDF(T5), slurry broadcasting (SB) (T6), and control(T7). The results showed that spinach grown with T4 80% RDF +BSN exhibited optimum plant height and leaf count compared to spinach under other treatments and was at par with T5 100% RDF for crop parameters. T5 treated plants demonstrated the longest roots, followed by T4 treated plants. The biomass produced by T4 was at par with T5 in the first (T4= 4.60 tonha-1, T5 =4.67 tonha-1) and second harvesting(T4= 6.69 tonha-1, T5 =6.89 tonha-1).In terms of macronutrient content in spinach leaves, significant differences were found only for nitrogen (N),potassium (K), while the phosphorus contents were not significantly influenced. Incorporating biogas slurry into the soil modifies microbial enzyme activities, specifically dehydrogenase and phosphatase. Normally, alkaline phosphatase shows greater activity than acidic phosphatase, but the addition of biogas slurry equalized the enzymatic activity of both, establishing a harmonized enzymatic profile. Fertilizing spinach with integrated Biogas slurry nutrigation + inorganic nutrigation not only improves growth and development to a similar extent as inorganic fertilizer but also enhances the nutrient content of the spinach, contributes to environmental preservation, and reduces production costs.

Additives can improve the efficiency of anaerobic digestion by increasing biogas production, reducing air pollution, and preventing total ammoniacal nitrogen (TAN) inhibition. Biological or chemical supplementation can also improve the economic efficiency of anaerobic digestion. However, the effects of specific additives on biogas production can vary depending on the type of supplement used. This research utilizes the additives on an industrial scale and monitors the optimization of the anaerobic digestion operating parameters after their addition. The various AD additives were examined in a sufficient cycle of operation for three biogas plants located in northern Greece. In this manner, the effectiveness was investigated in multiple initial feeds and unstable operating situations caused by the seasonality of specific feedstocks. The existing operation state in the three biogas plants was recorded before and after adding the supplements. In all three cases, lower concentration levels were observed in many of the examined trace elements. Introducing additives proved to be a stabilization factor in AD performance and inhibition mediator.

Herein, we report about the monometallic Ni and bimetallic Pd-Ni catalysts supported on CeO2-Al2O3 binary oxide, which were investigated in oxy-steam reforming of methanol (OSRM). Monometallic and bimetallic supported catalysts were prepared by wet aqueous impregnation and subsequent impregnation method, respectively. The physicochemical properties of the catalytic systems were investigated using various methods such as: BET, XRD, TPR-H2, TPD-NH3, XPS and SEM-EDS techniques. It has been proven that the addition of palladium to the nickel catalyst facilitates its reduction. The activity tests performed for all catalysts confirmed the promotion effect of palladium on catalytic activity of nickel catalyst and selectivity towards hydrogen production. Both nickel and bimetallic palladium-nickel supported catalysts showed excellent stability during the reaction. Such catalytic systems are valuable for the advance of the field of fuel cell technology.

Since fine powders tend strongly to adhesion and agglomeration, their processing with conventional methods is difficult or impossible. Typically, in order to enable the handling of fine powders, chemicals are added to increase the flowability and reduce adhesion. This contribution shows that instead of additives also vibrations can be used to increase the flowability, to reduce adhesion and cohesion, and thus to enable or improve processes such as precision dosing, mixing, and transport of very fine powders. The methods for manipulating powder properties are described in detail and prototypes for experimental studies are presented. It is shown that the handling of fine powders can be improved by using low-frequency, high-frequency or a combination of low- and high-frequency vibration.

: Sulfate presence is of great importance for anaerobic digestion as its addition can control the anaerobic microbial community. In this study, the effect of sulfuric acid addition on the perfor-mance of an UASB reactor fed with hydrolyzed starch was investigated. TOC, Fe and SO4-2 re-moval as well as the methane production were monitored under various COD/ SO4-2 ratios, HRTs and OLRs. When HRT was 16 hours and OLR equal to 2 g COD/LUASB-d the methane production was 0.24 L CH4/LUASB-day. After the sulfuric acid addition, TOC removal reached 95%. At HRT, OLR, and COD/ SO4-2 ratio equal to 16 hours, 2 g COD/ LUASB-d and 3.72 respectively, the methane production was 0.267 L CH4/LUASB-d. When the OLR was increased to 5.94 g COD/LUASB-d and COD/SO4-2 ratio was equal to 12.5, the methane production was 3 times higher (0.84 L CH4/LUASB-d) with a methane content in the produced biogas greater than 70%. 16s rRNA gene analysis demonstrated that after the sulfate addition, SRB were enriched and methane was mainly produced by Methanosaeta sp. This study indicates that appropriate sulfate concentrations in the feed in combination with the presence of iron in the UASB reactor lead to enhanced me-thane yields.

Agricultural product like cassava produces huge amounts of waste when processed to consumable goods. The waste generated is generally considered to contribute largely to environmental pollution. This study therefore investigates the waste management practice that is adopted by cassava processors in Ogun State, Nigeria. Five (5) Local Government Areas (LGAs) dominant in processing cassava were selected for the study on the basis of spatial location distribution; landmass and population. The survey involved the use of structured questionnaires administered to cassava processors of the selected LGAs. The Statistical Package for Social Sciences (SPSS) software application and descriptive statistics were used for data analysis. Results of the analysis show that majority (70%) of the cassava processors are females. Cassava peel constitutes 10% of the waste produced, of which 91% are heaped at refuse dump in most communities. Results also reveal that 86.3% of cassava residues are used for animal feeds. Other findings show that the peels when dried are used as bio-fuel for cooking and there is a significant potential for biogas production. From the data captured from respondent during the study, most processors are willing to pay for an improved waste management system. The study therefore suggests proper waste management of cassava waste to minimize environmental pollution.

Catalytic studies for hydrogen production via steam reforming of ethanol (SRE) are essential for process optimization. Likewise, selecting the ideal support for the active phase can be critical to achieve high conversion rates during the catalytic steam reforming. In this work, copper-based catalysts were synthesized using two different supports, NaY zeolite and Nb2O5/Al2O3 mixed oxides. The materials were prepared using wet impregnation and characterized for their physicochemical properties using different analytical techniques. Differences in catalyst morphologies were readily attributed to the characteristics of the support. The Cu/NaY catalyst showed better textural properties than Cu/Nb2O5/Al2O3, resulting in a homogeneous metal dispersion over the support surface. Both catalytic systems were active in SRE, but Cu/NaY resulted in higher ethanol conversions compared to Cu/Nb2O5/Al2O3. Hence, the performance of copper-based catalysts was influenced significantly by the textural properties of the support.

Hydrogen has been considered a future energy carrier for decades and the demand for hydrogen in refineries is always upward due to the revival of new technologies. The steam methane reforming method is frequently employed because of its high hydrogen generation efficiency at a cheap cost and minimal negative impact on the environment. But depending on the type of feedstock, one unit of hydrogen generate 9-10 units of CO2 that is needed to be treated for environmental sustainability. Therefore, the optimization of hydrogen production and CO2 capture is very important to address. The simulation research was conducted to anticipate and optimize steam reforming using Aspen HYSYS. A conversion-type reactor was used to develop this simulation-based model. The primary goal of this work is to investigate and optimize the production efficiency of hydrogen and the mitigation of CO2 that is generated from the steam reforming process by varying process parameters. CO2 capture efficiency was investigated at the different yields for hydrogen production and was found that a maximum of 98.8% of the CO2 can be absorbed using the proposed carbon capture system. Later, the Aspen Energy Analyzer tool revealed potential improvements for energy and cost optimization.

Energy from biogas is one of the most promising renewable energy sources. Significant, for technical, economic, and environmental reasons, is the construction of agricultural microgas plants next to households specialising in cattle rearing. The availability of free substrate makes it possible not only to produce one's electricity and heat but also to produce a more environmentally and human-friendly manure. The operation of biogas plants is, unfortunately, associated with technical problems. This paper presents the results of a study of the quality of electricity generated in an agricultural biogas plant built at a farm specialising in dairy cows, where the owner reported a problem with the voltage in the power supply network. Therefore, selected power quality parameters occurring at the connection point of the biogas plant were analysed in detail. As the authors' research showed, in the case in question, the agricultural biogas plant was connected via a cable with too small a conductor cross-section, which resulted in significant voltage exceedances, making it impossible to switch on the second of the biogas plant's generators. Replacement of the feed-in cable has enabled both generators to run, but significant fluctuations in the feed-in voltage values were still noticeable. Analysis of the subsequent measurements revealed the need for changes in the design of the digester itself. The proposal for change is to replace the two current digester mixers (each rated at 9 kW) with more mixers of lower power. The new mixers would operate in an alternating system, where only one would always be activated.

This case study focuses on exploring the potential of biogas as a direct substitute for conventional fossil fuels in industrial applications. Instead of being limited to its common uses as a vehicle fuel or for power generation, this research aims to investigate how biogas can be integrated into industrial processes as an advanced and sustainable energy solution. By conducting a detailed analysis of the financial implications associated with the utilization of landfill gas and gas derived from biomass, a comprehensive understanding of their practical applications in the industrial sector can be obtained. This research goes beyond a superficial examination and delves into the intricate aspects of incorporating biogas as a viable alternative fuel source. When we say that utilizing biogas is technically feasible, it means that the necessary infrastructure and technologies are available to support its integration into industrial processes. This implies that there are existing methods and systems in place that can efficiently harness and utilize biogas for various industrial applications. These technologies ensure a seamless transition from conventional fossil fuels to renewable energy sources, leading to a more sustainable and environmentally friendly industrial landscape. Moreover, the statement that utilizing biogas is economically feasible emphasizes that the financial viability of employing biogas in industrial processes is advantageous. This research explores the potential cost savings and benefits associated with substituting conventional fuels with biogas. By carefully examining the economic aspects, such as initial investments, operational costs, and potential revenue streams, a comprehensive understanding of the financial impact of adopting biogas solutions in the industrial sector can be gained. By expanding and broadening the understanding of the technical and economic feasibility of biogas integration, this research aims to provide valuable insights into the potential of advanced biogas solutions for industrial applications. Indeed, to make biogas a viable and sustainable option as a raw material, it is necessary to establish farming subsidies and financial support specifically tailored for biogas production, similar to the existing support provided for food production. These subsidies and financial incentives play a crucial role in promoting and encouraging the growth of the biogas industry. By establishing such support systems, farmers and other stakeholders in the agricultural sector can be incentivized to participate in the production of biogas. This can involve the utilization of agricultural waste, organic residues, or dedicated energy crops for biogas generation. The financial assistance can help offset the initial investment costs, provide incentives for production, and ensure the economic viability of biogas projects. Moreover, when considering large-scale landfills or situations where industrial demands for energy are relatively low, landfill gas becomes a viable and practical option. Landfill gas, which is generated by the decomposition of organic waste in landfills, can be harnessed and utilized for various industrial purposes. This not only helps in managing waste but also provides a valuable source of renewable energy. In summary, while farming subsidies and financial support are crucial for promoting biogas production, landfill gas remains a viable option for large landfills or situations with minor industrial demands. The combination of these two approaches offers a comprehensive outlook on utilizing biogas as a renewable energy source for industrial applications.

The paper presents a synthesis of deep eutectic solvents (DESs) based on choline chloride (ChCl) as hydrogen bond acceptor and phenol (Ph), glycol ethylene (EG), and levulinic acid (Lev) as hydrogen bond donors in 1:2 molar ratio. DESs were successfully used as absorption solvents for removal of dimethyl disulfide from (DMDS) from model biogas steam. Several parameters affecting the absorption capacity and absorption rate has been optimized including kind of DES, temperature, the volume of absorbent, model biogas flow rate, and initial concentration of DMDS. Furthermore, reusability and regeneration of DESs by means of adsorption and nitrogen barbotage followed by the mechanism of absorptive desulfurization by means of density functional theory (DFT) as well as FT-IR analysis were investigated. Experimental results indicate that the most promising DES for biogas purification is ChCl:Ph, due to high absorption capacity, relatively long absorption rate, and easy regeneration. The research on the absorption mechanism revealed that van der Waal interaction is the main driving force for DMDS removal from model biogas.

The kinetics of biogas production from biomass depends on several factors such as: carbon to nitrogen ratio (C/N), reactor temperature (T), and retention time (RT). The purpose of this study was to obtain a new model for predicting biogas production. Spent Mushroom Compost (SMC) was used to produce biogas in a batch type reactor. The experiments were carried out with different C/N ratios (12.1, 20, 30 and 40) and in both mesophilic (35°C) and thermophilic (55°C) temperatures. The results showed that the Maximum biogas production at 35°C, C/N=20 was equal to 41.9 mL/gVS and 55°C, C/N=30 was equal to 51.6 mL/gVS. By using experimental data, a new kinetic model was proposed to predict biogas production. Comparing the values of the results indicate that the total values of RMSE for Logistics, Gampartz and new kinetic models was 0.1906, 0.1830 and 0.1617, respectively. Therefore, the process of anaerobic digestion of biomass can be assumed to be just a chemical reaction, and the new kinetic model is an appropriate alternative to microbial growth models.

Due to rapid urbanization, the quantity of wastewater treatment plants (WWTP) has increased, and with it the amount of waste generated by them. Sustainable management of this waste can lead to the creation of energy-rich biogas through the fermentation process. This review presents recent advances in the anaerobic digestion process resulting in greater biogas production. Disintegration techniques for enhancing waste activated sludge fermentation can be generally partitioned into biological, physical and chemical, each of which are covered in this review. These disintegration techniques were compared mainly in terms of their biogas yield. It was found that ultrasonic and microwave disintegration provides the highest biogas yield (>500%); however, they are also the most energy demanding (>10,000 kJ kg-1 total solids).

Despite its growing importance as a dry beneficiation method, there is a lack of studies exploring the fundamentals aspects of dry jigging. In this sense, this study focuses on explore some essential aspects of density-based separation in dry jigs, like pulse profile, energy consumption and, especially, stratification over time, also exploring an innovative operational strategy here called “transient pulsation”. The tests were carried out using density tracers distributed across 11 density ranges (0.4-2.4 g/cm³) and employing a base bed (gravel) to analyze their segregation in a pilot-scale dry jig. Pressure drop and active power data were acquired to measure the pulse characteristics and energy consumption. The findings suggest that establishing the dry jigging cycle is more complex than in hydraulic jigs due to the compressibility of air. Stationary pulsation tests revealed an unstable behavior of stratification over time, contrasting with traditional hydraulic jigs, while transient pulsation tests unveiled varied trends in separation quality. Energy consumption analysis underscored the significant role of the blower drive. These insights have the potential to inform operational enhancements in dry jigging.

Age-related macular degeneration (AMD) is a leading cause of irreversible blindness world-wide. We recently reported that polyethylene glycol (PEG) can activate the alternative pathway of the complement system and induce choroidal neovascularization (CNV) in mice. Currently, no other investigator has demonstrated CNV after PEG injection in the mouse eye. The aim of this article is twofold: we review the histologic changes in mouse retina and retinal pigmented epithelium (RPE) after treatment with PEG, and we summarize a model of wet and dry AMD pathogenesis in mice through subretinal PEG treatment of RPE cells and retinal layers. We injected (subretinal) male C57BL/6 mice with 2 μL of solution containing 0.5 mg and 1.0 mg of PEG or PBS in control groups. Eyes were harvested at day 1, 3 and 5 after injection and processed for analysis. Sections were immunohistochemically stained for complement component C3, mem-brane attack complex (MAC), and cytokeratin 18. Light and laser confocal microscopy was used for image capturing. PEG increased deposition of C3 and MAC on RPE cells and on all retinal layers after 1.0 mg injection. PEG induced loss of cellular contacts between RPE cells and migration of RPE cells in the subretinal space at day 1 after PEG injection. After 0.5 mg PEG injection, increased size of RPE cells was detected at day 3 and 5. Apoptotic bodies were observed in outer nuclear layer at day 3 and 5 after 0.5 mg PEG treatment. RPE cells with dark cytoplasm and condensed chromatin were observed. Higher doses of PEG induce CNV, encouraged RPE cell proliferation and death, and damage photoreceptors in mice. This simple and fast model may be useful to explore the pathogenesis of both dry and wet AMD.

The basis of the work of electroencephalography (EEG) is the registration of electrical impulses from the brain or some of its individual areas using a special sensor/electrode. This method is used for the treatment and diagnosis of various diseases. The use of wet electrodes in this case does not seem viable, for several well-known reasons. As a result of this, a detailed analysis of modern EEG sensors developed over the past few years is carried out, which will allow researchers to choose this type of sensor more carefully and, as a result, conduct their research more competently. Due to the absence of any standards in the production and testing of dry EEG sensors, the main moment of this manuscript is a detailed description of the necessary steps for testing a dry electrode, which will allow researchers to maximize the potential of the sensor in the various type of research.

CuO/ZnO/Al2O3 catalyst is a commonly used catalyst for rea methanol steam reforming reaction. Oxalic acid was as precipitant in preparing oxalate precursor of CuO/ZnO/Al2O3 catalyst by co-precipitation, deionized water and ethanol were as solvents, microwave irradiation and water bath were as aging heating manner respectively. It indicated that ethanol selected crystal phase composition of oxalate precursors and restricted their growth. Microwave irradiation prompted the isomorphous substitution between Cu2+ of CuC2O4 and Zn2+ of ZnC2O4 in mother liquid, forming the master phase (Cu,Zn)C2O4 in precursor, the solid solution Cu-O-Zn formed after calcination, which exhibited nano-fibriform morphology. It possessed small CuO grains, large surface area and strong synergy between CuO and ZnO, which is beneficial to improve the catalytic performance of methanol steam reforming, the STY of H2 reached 516.7 mL·g-1·h-1, and the selectivity of CO was only 0.29%.

This study was conducted to determine the effect of different types of olive cake (five treatments) in the diet of Bísaro pigs on the volatile compounds and sensory characteristics in the dry-cured loin and dry-cured “cachaço” (2 processed meat products). The treatments applied are based on the type of extraction and this may imply differences in their water and fat content. Eighty com-pounds were identified, and grouped into eight chemical classes: hydrocarbons, aldehydes, es-ters, alcohols, ketones, acids, furans, and other compounds. Aldehydes and alcohols were the ma-jor groups of compounds, representing 57.06-66.07 % and 68.67-75.61 % for the loin and “cacha-ço”, respectively. There were no significant differences between treatments for any of the volatile compounds identified. The major aldehydes were hexanal, heptanal, pentanal, and propanal. These compounds were significantly higher (p<0.001) in “cachaço”. This significant difference be-tween the two types of dry-cured products is directly related to the amount of total fat content. The major alcohols were 2.3-butanediol, 1-octen-3-ol, 1-butanol, 3-methyl, 1-hexanol, benzyl-alcohol and glycidol. Except for compounds 2,3-butanediol and benzyl-alcohol, the majority in this group are significantly different in terms of the type of dry-cured product. As for the sensory evaluation, for both dry-cured products, the trained tasters did not detect significant differences between the different treatments, which is in line with the results obtained for volatile compounds.

The decentralized treatment of wastes is studied for an urban scenario considering a high-density population of 2500 inhab./km2. Food and garden waste were assumed to be treated in a co-digestion configuration using several mid-size digesters. In contrast biogas and digestate valorization were carried out in a centralized manner. Electricity and thermal energy were produced from this configuration, accounting for 1.3% of residential electricity demand and 3.2% of thermal demand when using double-turbocharged engines. However, the location of the treatment plants is a factor that may raise social discomfort. Rejection of locating the plant in specific sites close to residential neighbors, nuisance due to possible odor and gaseous emissions, and house market distortions are just a few of a long list of problematic aspects that may threaten the decentralized alternative. These factors are of great relevance and must be given a practical solution if the circular economic model is to be implemented by considering the insertion of waste streams into the production system and generating local energy sources and raw materials.

Roller milling of sorghum and quinoa seeds into flour fractions (course, middle, and fine) was investigated, chemically analysed and applied in the baking of gluten-free sourdough bread. Gap settings were adjusted to 0, 5, 8 and 10 for quinoa and 3, 5, and 7 for sorghum. The fine fractions reached values of up to about 41% (gap 8) for quinoa and around 20% for sorghum (gap 5). SEM pictographs illustrated clear separation of each fraction with chemical analysis showing high contents of protein, TDF (total dietary fibre) and IDF (insoluble dietary fibre) in the course fraction. Up to 77% starch content was obtained in the fine fraction with significant amounts of SDF (soluble dietary fibre) which has good health benefits. Increasing the dough moisture up to 90% helped in decreasing the bread crumb firmness, while low Avrami parameters and RVA pasting behaviour indicated slow bread staling rate for both sourdough breads.

The article presents comparative results from 5 categories of animals (4 samples originating from pigs, 2 from cows, 1 from chicken, 1 from ostriches, 1 from horses, samples quantified with A, B, C, D, E, F, G, H, I). These samples were collected from large, medium and small (family) farms. The results were validated by the biogas production generated by the respective samples, using the Automatic Methane Potential Test System (AMPTS II) bio-processor. The largest amounts of biogas (2,464.5 Nml, 2,262.0 Nml) were recorded for the samples from pig farms (Sample B and Sample D), whereas the lowest values were obtained in the case of Sample A (414.1 Nml) and Sample C (558.3 Nml). The heavy metals analyzed in the article are Zn, Cu, Fe, Mn, Ca, K, As. The results corroborate that the C/N ratio can also vary to values lower than 20-30, without affecting the biogas production process, and the heavy metal content must be known especially for the full management of the wastes. All final data presented in the article are based on repeated, triplicate experiments, with less as 2% deviation between data.

The Bacillus megaterium LVN01 species native to Colombia has demonstrated the ability to metabolize different co-products or industrial waste (such as fique juice, cane molasses, residual glycerol) and accumulate polyhydroxybutyrate (PHB), giving it potential in the bioplastics industry. In this research, the potential of liquid digestate as a carbon source for the production of PHA in fermentation processes with this bacterial strain was evaluated. Favorably, it was found that B. megaterium utilizes the nutrients from this residual substrate to multiply appropriately and efficiently synthesize poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV). Bench scale aerobic batch fermentation, under the operational conditions of this research [Volume: 3L; Temperature: 30.8°C; Agitation: 400 rpm; pH: 7.0 ± 0.2; Disolved Oxygen: 100% saturation; Antifoam 10% (v/v)], generated maximum values of DCW (0.56 g cell L-1) at 60 h, while the maximum PHB yield (360 mg PHB L-1) occurred at 16 h, which is very favorable for sustainable degradable bioplastics production. Additionally, GC-MS and NMR analyses confirmed that the PHBV copolymer synthesized by B. megaterium is made up of the monomers 3-hydroxybutyrate (3HB) and 3-hydroxyvalerate (3HV). Furthermore, the thermal properties determined by TGA (Tonset=283.1 ºC, Tendset= 296.98 ºC. Td =290.114 °C) and DSC (Tm= ºC155.7 °C, ΔHf= 19.80 J g-1, Xcr = 18.17%), indicate that it is a thermally stable biopolymer with low percentages of crystallinity, providing flexibility that facilitates molding, adaptation, and application in various industrial sectors.

This study investigates the efficiency of a biogas-powered cooling system through the utilization of energy and exergy calculations. Biogas, which can be generated and stored in small-scale plants as needed, serves as a viable fuel source for absorption cooling systems. The present research focuses on the biogas consumption of a triple-effect absorption cooling system, specifically designed to supply a fixed cooling load of 100 kW under varying operational conditions. The study highlights the COP (Coefficient of Performance) and ECOP (Exergetic Coefficient of Performance) values of the system, along with the exergy destruction rates of its individual components, at the optimal temperatures of operation. Furthermore, to determine the necessary biogas consumption, the study explores the establishment of dedicated farms for various animal species, ensuring an adequate number of animals for biogas production. The findings reveal a COP of 1.78 and an ECOP of 35.4% at the optimized operating temperatures. The minimum mass flow rate of biogas is determined to be 0.0034 kg/s, facilitating the operation of the boiler with a methane content of 65%. The study concludes that a total of 290 head of cattle is required to generate the annual biogas consumption necessary for the cooling system. Also, number of the cattle is enough to establish 284 biogas plants in Bursa province in Türkiye.

Dry eye disease (DED) is a multifactorial disorder in which tear fluid homeostasis is lost, resulting in increased tear film osmolarity and ocular surface irritation. In Asia, the short tear film breakup time type-DED is common, and stabilization of the tear film is the first goal of treatment. Treatment of DED begins with eye drops. Until now, artificial tears and steroid eye drops have been the main treatment for DED. However, artificial tears require frequent administration of eye drops and thus pose adherence problems, while steroids have problems with side effects (cataracts, increased intraocular pressure). This review evaluates the new generation of DED therapies in Asia based on what is known about them and demonstrates that they are more effective for DED than traditional therapies such as artificial tears and steroids. Based on these considerations, it is proposed that the optimal treatment for DED in Asia is the initial application of mucin secretion enhancing eye drops (long-acting diquafosol) and oral supplements, and if additional treatment is needed, cyclosporine eye drops and the adjunctive therapies presented in this review are added.

Ultrasound is a well-known tool to produce thermal and non-thermal effects on cells and tissues. These effects require a correct application of ultrasound in terms of localization and acoustic energy delivered. This article describes a new device that combines ultrasound and Dry Needling treatments. The ultrasound transducer can rotate in 3D space mechanically to align itself in the direction of the needle. The transducer electronically focuses the acoustic pressure automatically on the needle tip and its surroundings. A computer, using graphical interface software, controls the angulation of the array and the focus position.

Background: Aflatoxins (AFs) as toxic compounds are widely spread. They are frequent contaminants of crops that are produced by fungi species. Corn is of crops that widely used in the corn dry milling process; a four-step procedure comprises grain handling and milling, liquefaction and saccharification, fermentation, and co-product recovery that produces ethanol and animal feed. However, it is possible that corn as a feed for dry milling process might be contaminated with AFs. Therefore, monitoring AFs in during widespread this process results having a better understanding of the fate of AFs. Methods: In this study, a sample of corn kernel was contaminated with a high level of AFs using Aspergillus parasiticus. Then, the corn flour comprising 23400.5 µg/kg of the total level of aflatoxins (AFT), was hydrolyzed by enzymes and acid for ethanol fermentation with Saccharomyces cerevisiae. Also, the level of AFs was monitored during ethanol fermentation process. Results: The results showed that AFs did not detect in the ethanol produced through fermentation and it was safe. Also, during the experiments, the AFT level reduced by 58.5 and 95.7% for the ethanol fermentation with simultaneous saccharification and fermentation and ethanol production with acidic hydrolysis, respectively. Conclusion: The results of this study showed that highly contaminated corn with AFs can be used for ethanol fermentation through dry milling process and the produced ethanol was safe.

Each year in March, adherents of the Bahá’í faith abstain from eating and drinking from sunrise to sunset for 19 days. Thus, Bahá’í fasting (BF) can be considered as a form of daytime dry fasting. We tested if BF decreases energy expenditure after a meal and improves anthropometric measures, and systemic and tissue-level metabolic parameters. This was a self-controlled cohort study with 11 healthy men. We measured anthropometric parameters, metabolic markers in venous blood, and pre- and postprandial energy metabolism at systemic (indirect calorimetry) and tissue (adipose tissue and skeletal muscle microdialysis) level, both before and during BF. During BF, we found reduced body weight, body mass index, body fat and blood glucose. Postprandial increase in energy expenditure was lower, diet-induced thermogenesis tended to be lower. In adipose tissue, perfusion, glucose supply and lipolysis were increased. In skeletal muscle, tissue perfusion did not change. Glucose supply and lipolysis were decreased. Glucose oxidation was increased, indicating an improved insulin sensitivity. BF may be a promising approach to losing weight and improving metabolism and health. However, outside the context of religiously-motivated fasting, skipping a meal rather in the evening (dinner cancelling) might be recommended, as metabolism appears to be reduced in the evening.

The interest in dry EEG electrodes has increased in recent years and especially as everyday suitability earplugs for measuring drowsiness or focus of auditory attention. However, the challenge is still the need for a good electrode material, which is reliable and can be easily processed for highly personalized applications. Laser processing as used here is a fast and very precise method to produce personalized electrode configurations that meet the high requirements of in-ear EEG electrodes, for example. The arrangement of the electrodes on the very flexible and compressible mats allows an exact alignment of the electrodes to the ear mold and contributes to a high wearing comfort, as no edges or metal protrusions are present. For better transmission properties, an adapted coating process for surface enlargement of platinum electrodes is used, which allows easy control of the thickness and growth form of the porous layer. The porous platinum-copper alloy is chemically very stable, shows no exposed copper residues and enlarges the effective surface area by 40. In a proof-of-principle experiment, these porous platinum electrodes could be used to measure the Berger effect in a dry state using just one ear of a test person. Their signal-to-noise ration and frequency transfer function is comparable to gel-based silver/silver chloride electrodes.

(1)Background: Early-age concrete shrinkage induces stress that impact the cost and service life of concrete pavements. (2)Methods: In this study, strain measurements of field slabs were conducted and a methodology was presented that independently derived autogenous, drying, and thermal shrinkages in the initial stages of concrete placement. Total strain was measured according to five different environmental conditions and shrinkage strain was calculated for each condition. (3)Results: By measuring the strain of the slab and the specimen, the drying shrinkage strain was measured to be approximately 54% better than that by the conventional non-stressed cylinder method because it was possible to measure the drying shrinkage strain at the surface rather than in the middle part of the slab along its depth direction. When the water-to-cement ratio increased (35→40%), there was a considerable reduction (317με→82με) of autogenous shrinkage strain for the concrete at 28 days of age. Furthermore, calculation of stress-dependent strain allowed the presentation of more intuitive and accurate results. (4)Conclusion: As the measurement of independent shrinkage occurrence is possible, the consequent calculated result of the stress-dependent strain acting on real slabs will facilitate improvement in the construction quality, reduction in the development of defects in the concrete structure, and increase in the service life.

Ferric oxide containing waterworks sludge can be used to reduce formation of hydrogen sulfide during anaerobic digestion. The ferric compound is reduced biochemically in the digester and forms insoluble pyrite in digester sludge. Often virgin ferric chloride is used to solve the hydrogen sulfide problem. Since 2013, Sydvatten AB has supplied a growing number of digestion plants in Sweden with ferric containing dewatered waterworks sludge from the drinking water treatment plant Ringsjöverket to limit the formation of hydrogen sulfide. At the waterworks, ferric chloride is added to enhance coagulation of organic matter from the source water. The sludge formed in this process is dewatered and landfilled, but also recycled in the biogas production in order to reduce the hydrogen sulfide concentration. In this study, the use of sludge, for hydrogen sulfide removal in digesters, was technically and economically evaluated from cases studies from 13 full-scale digesters in Sweden. Compared with use of fresh ferric chloride, the operational costs are reduced up to 50 % by using sludge. The quality of the sludge is high and its content on metals is low or very low, especially when compared with requirements from different certification standards on biosolid reuse applied in Sweden. An addition of waterworks sludge containing iron to a digester for removal of dissolved hydrogen sulfide is a technically and economic good alternative when producing biogas. It is also one step closer to a circular economy, when replacing use of virgin chemicals with the by-product waterworks sludge which saves energy, material and reduces the carbon foot-print of the waterworks.

Traditional dry fermented meat products are obtained artisanally in many countries, where they represent a gastronomic heritage well distinguished from industrial counterparts. This food category is most often obtained from red meat, a food commodity that is under attack because of evidences of increased risk of cancer and degenerative diseases with high consumption. However, traditional fermented meat products are intended for moderate consumption and gastronomic experience and, as such, their production must be continued also to safeguard culture and economy of the geographical areas of origin. In this review, the main risks attributed to these products are considered and how these risks are minimized by following precise production norms, respectful of the ancient manufacturing processes is described. Moreover, results obtained in studies reporting use of autochthonous microbial cultures of lactic acid bacteria (LAB), coagulase negative staphylococci (CNS), Debaryomyces hansenii and Penicillium nalgiovense to improve safety and quality of traditional fermented meats are summarized. The role of these products as a source of microorganisms that can be beneficial to the host are also considered. From the results of the studies reviewed here it appears that the development of autochthonous cultures for these foods ensure safety and stabilize sensory characteristics with possibility to be extended to the large variety of traditional productions.

Data on the seasonally dry tropical forests of Mexico have been examined in the light of statistical mechanics. The results suggest a division into two classes of species. There are drifting populations of a cosmopolitan class capable of existing in most dry forest sites; these have a statistical distribution previously only observed (globally) for populations of alien species. A high proportion of species found only at a single site are endemic and these prefer sites comparatively low in species richness.

With the application of high-precision, enormous rotating equipment and the addition of harsh working conditions, the advantages of dry gas sealing technology are increasingly obvious. Herein, research on the dynamic stability of dry gas seals is reviewed based on their operating mechanism. The influence of the dry gas seal structure, vibration response, and dynamic followability on the reliability of the shaft end sealing system of rotating machinery is the focus of current dry gas sealing technology. This work reviews the research history; analyzes the key coefficient of instability of the sealing system under external disturbances and the existing research on stability models; discusses the influence of starting and stopping characteristics, working conditions, and groove parameters on the stability of dry gas seals; and points out the shortcomings in the existing research. In addition, potential developments in dynamic stability are proposed, including improving model accuracy, improving experimental techniques, or applying intelligent control and optimization methods to enhance the dynamic stability of the sealing system. Finally, the development prospects for dry gas sealing technology in intelligent monitoring and wide temperature range adaptations are discussed, and theoretical guidance for improving the dry gas seal system is provided.

A simple fabrication method in the surface modification of electroosmotic silicon microchannel using thermal dry oxidation is presented. The surface modification is done by coating the silicon surface with a silicon dioxide (SiO₂) layer using thermal oxidation process. The process is aimed not only to improve the surface quality of the channel to be suitable for electroosmotic fluid transport but also to reduce the channel width using a simple technique. Initially, the parallel microchannel array with dimensions of 0.5 mm length and width ranging from 1.8 µm to 2 µm are created using plasma etching on the 2x2 cm <100> silicon substrate. The oxidation of silicon channel in a thermal chamber is then conducted to create the SiO₂ layer. The layer properties and the quality of the surface are analyzed using SEM and surface profiler, respectively. The results show that the maximum oxidation growth rate occurs in the first 4 hours of oxidation time and the rate decreases by time as the oxide layer becomes thicker. It is also found that the surface roughness is reduced with the increase of process temperature and oxide thickness. The scallop effect on the vertical wall due to plasma etching process also improved with the presence of the oxide layer. After the oxidation, the channel width is reduced by ~40%. The demonstrated method is suggested for the fabrication of a uniform channel cross section with high aspect ratio in sub-micro and nanometer scale that will be useful for the electroosmotic flow (EOF) manipulation of the biomedical fluid sample.

A unique method for synthesizing a surface modifier for metallic hydrogen permeable mem-branes based on non-classic bimetallic pentagonally structured Pd-Pt nanoparticles has been de-veloped. It was found that nanoparticles had unique hollow structure. This significantly reduces the cost of their production due to economical use of metal. According to the results of electro-chemical studies, synthesized bimetallic Pd-Pt/Pd-Ag modifier showed excellent catalytic activi-ty (up to 60.72 mA cm–2), long-term stability and resistance to COads poisoning in alkaline oxida-tion reaction of methanol. The membrane with pentagonally structured Pd-Pt/Pd-Ag modifier showed the highest hydrogen permeation flux density up to 27.3 mmol s–1 m–2. Obtained hy-drogen flux density were 2 times higher than that for membranes with classic Pdblack/Pd-Ag modifier and an order of magnitude higher than that for unmodified membrane. Since the rate of transcrystalline hydrogen transfer through a membrane increased, while the speed of transfer through defects remained unchanged, a one and a half times rise in selectivity of the developed Pd-Pt/Pd-Ag membranes was recorded and it amounted to 3514. Achieved results are due to both the synergistic effect of the combination of Pd and Pt metals in the modifier composition and the large number of available catalytically active centers, which are present as a result of non-classic morphology with high-index facets. The specific faceting, defect structure and unusual properties provide great opportunities for the application of nanoparticles in the areas of membrane reac-tors, electrocatalysis, petrochemical and hydrogen industries.

The study examines projected changes in dry- and wet-spell probabilities in West Africa using a Markov chain approach. Four simulations of regional climate models from the CORDEX-Africa program were used to analyze projected changes in intraseasonal variability. The results show an increase in the probability of having a dry day, a dry day preceding a wet day and a dry day preceding a dry day, and a decrease in the probability of wet days in the Sahel region under anthropogenic forcing scenarios RCP4.5 and RCP8.5. The decrease in wet days is stronger in the far future and under the RCP8.5 scenario (up to -30%). The study also finds that the probability of consecutive dry days (lasting at least 7 days and 10 days) is expected to increase in the Western Sahel, the Central Sahel, and the Sudanian Area under both scenarios, with stronger increases in the RCP8.5 scenario. In contrast, the decrease is expected over the Guinea Coast, with the changes more important under the RCP4.5. These changes in dry- and wet-spell probabilities are important for water management decisions and risk reduction in the energy and agricultural sectors. The study also highlights the need for decision-makers to implement mitigation and adaptation policies to minimize the adverse effects of climate change.

This study aimed to develop a high-quality dry emulsion incorporating omega-3, 6, and 9 fatty acid-rich ostrich oil for use as a dietary supplement. Extracted from abdominal adipose tissues using a low-temperature wet rendering method, the ostrich oil exhibited antioxidant properties, favorable physicochemical properties, microbial counts, heavy metal levels, and fatty acid compositions, positioning it as a suitable candidate for an oil-in-water emulsion and subsequent formulation as a dry emulsion. Lecithin was employed as the emulsifier due to its safety and health benefits. The resulting emulsion, comprising 10% w/w lecithin and 10% w/w ostrich oil, was stable, with a droplet size of 3.93 ± 0.11 μm. This liquid emulsion underwent transformation into a dry emulsion to preserve the physicochemical stability of ostrich oil, utilizing Avicel® PH-101 or Aerosil® 200 through a granulation process. Although Aerosil® 200 exhibited superior adsorption, Avicel® PH-101 granules surpassed it in releasing the ostrich oil emulsion. Consequently, Avicel® PH-101 was selected as the preferred adsorbent for formulating the ostrich oil dry emulsion. The dry emulsion, encapsulated with a disintegration time of 3.11 ± 0.14 min for ease of swallowing, maintained microbial loads and heavy metal contents within acceptable limits. Presented as granules containing butylated hydroxytoluene, the dry emulsion showcased robust temperature stability, suggesting the potential incorporation of animal fat into dry emulsions as a promising dietary supplement.

Carbon fiber reinforced polymers (CFRPs) are being used extensively in modern industries that require high strength-to-weight ratio such as aerospace, automotive, motorsport, and sports equipment. However, although reinforcement with carbon fibers improves the mechanical properties of polymer, this comes on the expense of abrasive wear resistance. Therefore, to efficiently utilize CFRPs in dry sliding contacts, solid lubricant is used as a filler. Further, to facilitate fabrication of objects with complex geometries, selective laser sintering (SLS) can be employed. Accordingly, in the present work, graphite-filled carbon fiber-reinforced polyamide 12 (CFR-PA12) specimens were prepared using SLS process to explore the dry sliding friction and wear characteristics of the composite. The test specimens were aligned along four different orientations in the build chamber of SLS machine to determine the orientation-dependent tribological properties. The experiments were conducted using pin-on-disc tribometer to measure the coefficient of friction (COF), interface temperature, friction-induced noise, and specific wear rate. In addition, scanning electron microscopy (SEM) of tribo-surfaces was conducted to specify the dominant wear pattern. The results indicated that the steady state COF, contact temperature, and wear pattern of graphite-filled CFR-PA12 are orientation-independent, and that the contact temperature is likely to approach an asymptote far below the glass transition temperature of amorphous PA12 zones, thus eliminating the possibility of matrix softening. Additionally, the results showed that the Z-oriented specimen exhibits the lowest level of friction-induced noise along with the highest wear resistance. Moreover, SEM of tribo-surfaces determined that abrasive wear is the dominant wear pattern.

This study aims to assess the interface shear adhesion behaviour between compacted clay and a metallic surface. A new testing approach was developed in this study for this purpose. The proposed method is simple and requires neither advanced equipment nor special test procedures, and thus represents an improvement on existing practice in this field. The experimental program involves determining the interface shear adhesion strength of reconstituted Kaolin clay/metallic surface where the Kaolin clay testing specimens were compacted dynamically at different energy levels and moisture contents. In general, the results show that the interface shear adhesion strength increases as the dry density of the clay increases, whereas it decreases as the moisture content increases. Furthermore, the results in this study reveal a unique multistage interfacial shear adhesion strength behaviour as the moisture content changes that could be related to the compaction curve of the clay. The observed behaviour, in this study, could be interpreted in terms of the effect of clay dry density and moisture content on the contact area and moisture-induced capillary adhesion at clay particles-continuum interface surface.

: The objective of this study was to obtain different dry matter contents and proportions of mel-on plant biomass for silage making. A completely randomized design was adopted with a facto-rial scheme (3 x 2) in four replications. The first factor corresponded to three mixtures of melon biomass on as fed basis (AF) of plant (branch + leaf) and fruit (harvested melon) as follows: 100% plant, 90% plant + 10% fruit, and 100% fruit. The other factor corresponded to the ensiled materi-al with fresh and dehydrated melon plant biomass (40% DM) which was dried in the field, after harvest. Silages with partial dehydration of the biomass available after fruit harvest with 0% and 10% fruit showed the greatest DM values: 297 and 293 g/kg DM, respectively. Silages with 0, 100 and 10% fruit showed medium LAB populations: 5.79, 5.14 and 4.58 logs CFU/g, respectively. Higher concentrations of acetic acid contents were observed in silages with 0 and 10% fresh fruit, which were 14.9 and 14.1 g/kg DM, respectively. Silages with 0% and 100% of dehydrated fruit showed better results for the indicators of good-quality silage. Dehydration improves the fer-mentative profile and quality of the melon silage.

Ultra-short 230 fs laser pulses of 515 nm wavelength were tightly focused into 700 nm focal spots and utilised in opening ~ 0.4 − 1 μm holes in alumina Al2O3 etch masks with 20-50 nm thickness. Such dielectric masks simplify fabrication of photonic crystal (PhC) light trapping patterns for the above-Lambertian performance of high efficiency solar cells. Conditions of laser ablation of transparent etch masks and effects sub-surface Si modifications were revealed by plasma etch- ing, numerical modeling, and minority carrier lifetime measurements. Mask-less patterning of Si is proposed using fs-laser direct writing for dry plasma etch of Si.

The alteration of the delicate balance that regulates the secretion and distribution of the tear film determines the dry eye (DE) syndrome, because the tear film represents the interface between the eye and the environment. Despite having a multifactorial origin, the main risk factors for the emergence of the ocular disease are female gender and advanced age. Likewise, morphological changes in several glands and in chemical composition of their secretions such as proteins, mucins, lipidics, aqueous tears, and salinity, are highly relevant factors to maintain a condition of good health of the ocular anterior segment. Another key factor of recurrence and onset of the disease is the presence of local and/or systemic infiammation that reflex on the ocular surface. However, it is one of the most commonly encountered disease in clinical practice and many other causes related to daily life and to lengthen the average life will contribute to the beginning. This review will consider how and what disorders of the ocular surface are responsible for a widespread pathology so. In the end, the most appropriate and new therapies will be briefly exposed according to the specific pathology.

Anchovies are amid the largest fish catch worldwide. The anchovy fillet industry generates a huge amount of biowaste (e.g. fish heads, bones, tails) that can be used for the extraction of several potentially valuable bioproducts including omega-3 lipids. Following the extraction of valued fish oil rich in omega-3, vitamin D₃ and zeaxanthin from anchovy fillet leftovers using biobased limonene in a fully circular process, the solid residue was used as starting substrate for the production of biogas by anaerobic digestion. The results first reported in this study demonstrate good potential energy recovery of the anchovy sludge of about 280 mL_CH4∙g_VS^-1. Due to unbalanced C/N ratio typical of marine biowaste, co-digestion with a carbon rich substrate is recommended.

Reference evapotranspiration (ET0) plays an irreplaceable role in regional dry/wet conditions under the background of climate change. Based on the FAO Penman-Monteith method and daily climate variables, ET0 was calculated for 22 stations in and around Songnen Grassland, northeast China, during 1960-2014. The temporal and spatial variations of ET0 and precipitation (P) were comprehensively analyzed at different time scales by using the Mann-Kendall test, Sen’s slope estimator, and linear regression coupling with break trend analysis. Sensitivity analysis was used to detect the key climate parameter attributed to ET0 change. Then, the role of ET0 in regional dry/wet conditions was discussed by analyzing the relationship between ET0, P and aridity index (AI). Results shown a higher ET0 in the southwest and a lower in the northeast, but P was opposite to that of ET0. Evidently decreasing trend of ET0 at different time scales was detected in almost the entire region, and the significant trend mainly distributed in the eastern, northeastern and central. For the whole region, sensitivity analysis indicated decreasing trend of ET0 was primarily attributed to relative humidity and maximum air temperature. The positive contribution of increasing temperature rising to ET0 was offset by the effect of significantly decreasing relative humidity, wind speed and sunshine duration. In addition, the value of ET0 shown higher in drought years and lower in wet years.

Knowing, with reasonable accuracy, the dry matter (DM) content of Hass avocado fruit will help determine when the fruit must be harvested. The reliability of predictive models based on near infrared spectra for DM quantification depends on the ability of the spectra to be representative of the DM gradient within a whole fruit. The aim of this work was to develop a methodology to determine the optimum number of spectra to develop a robust model for DM content quantification. Three spectra were recorded for each zone of the intact fruit: peduncle, equator, and base. Each scanning point was sampled, and the DM content was determined using oven drying. Two-way ANOVA confirmed the DM gradient within the whole fruit. This gradient was observed within spectra using the RMS (root mean square) criterion and PCA. The PLS models showed that at least one spectrum per zone could be enough to construct an efficient and robust model for dry matter quantification.

Snowpack loss in midlatitude mountains is ubiquitously projected by Earth system models, though the magnitudes, persistence and time horizons of decline vary. Using daily downscaled hydroclimate and snow projections we examine changes in snow seasonality across the U.S. Pacific Southwest region during a simulated severe 20-year dry spell in the 21st century (2051–2070) developed as part of the 4th California Climate Change Assessment to provide a "stress test" for water resources. Across California’s mountains, substantial declines (30–100% loss) in median peak annual snow water equivalent accompany changes in snow seasonality throughout the region compared to the historic period. We find 80% of historic seasonal snowpacks transition to ephemeral conditions. Subsetting empirical-statistical wildfire projections for California by snow seasonality transition regions indicates a two-to-four-fold increase in burned area, consistent with recent observations of high elevation wildfires following extended drought conditions. By analyzing six of the major California snow-fed river systems we demonstrate snowpack reductions and seasonality transitions result in concomitant declines in annual runoff (47-58% of historic values). The negative impacts to statewide water supply reliability by the projected dry spell will likely be magnified by changes in snowpack seasonality and increased wildfire activity.

The present study illustrates a brain-computer interface designed and developed to be wearable, portable, and user-friendly. Eight dry electroencephalographic sensors were adopted to acquire the brain activity associated with motor imagery. Multimodal feedback in extended reality was exploited to improve the detection of neurological phenomena. Twenty-seven healthy subjects used the proposed system in five sessions to investigate the effects of feedback on motor imagery. The sample was divided into two equal-sized groups: the "neurofeedback" group, which performed motor imagery while receiving feedback, and the "control" group, which performed motor imagery with no feedback. Several questionnaires were administrated to participants aiming to investigate the usability of the proposed system and individual’s ability to imagine movements. The highest mean classification accuracy across subjects of control group was about 62 % with 3 % associated type A uncertainty, and 69 % with 3 % uncertainty for neurofeedback group. Moreover, in some cases the results were significantly higher for the neurofeedback group. The perceived usability by all participants was high. Overall, the study highlights the advantages and the pitfalls of using a wearable brain-computer interface with dry sensors. Notably, the results and the perceived usability pave the way for the employment of the proposed system in tele-rehabilitation.

Transition between the unfolded and native states of the ordered globular proteins is accompanied by accumulation of several intermediates, such as pre-molten globule, wet molten globule, and dry molten globule. Structurally equivalent conformations can serve as native functional states of intrinsically disordered proteins. This overview captures the characteristics and importance of these molten globules in both structured and intrinsically disordered proteins. It also discusses examples of engineered molten globules. The formation of these intermediates under the conditions of macromolecular crowding and their interactions with nanomaterials are also reviewed.

Dry eye disease (DED) most commonly caused by evaporative subtypes and mainly induced by meibomian gland dysfunction (MGD). Intense pulsed light (IPL) combined with meibomian gland expression (MGX) is noninvasive treatment for improvement of ocular discomfort symptoms and MGD. In this prospective study between November 2020 and May 2022, the patients met the criteria of both ocular surface disease index (OSDI) ≥13 scores and standardized patient evaluation of eye dryness (SPEED)≥ 8 scores were enrolled in Kaohsiung Veteran General Hospital. Three separate treatment sessions of IPL therapy combined with MGX administered to the lower lids with an interval of 28 days. Further tear film assessment included lipid layer thickness (LLT), tear meniscus height (TMH), non-invasive tear break-up time (NIBUT), meibomian gland loss (MGL) either beforeor after 1st and 3rd IPL therapy combined with MGX. Besides, lissamine green staining and pain scores were also recorded. We totally enrolled 37 patients of 74 eyes. Men accounted for 18.92% (7/37). The mean age was 54.51 ± 11.72 years. The mean OSDI scores were 58.12 ± 22, while the SPEED scores were 17.03 ± 5.98. The mean Schirmer’s test was 3.66 ± 2.43 mm. After three sessions IPL treatment with MGX, the OSDI, SPEED, LLT, TMH, MGL, MGXS and pain scores were significantly improved. For the MGX scores (MGXS) ≤20 group, MGL and lissamine green scores showed significant improvements. For the MGXS >20 group, TMH and dry spot rate revealed statistically improvement. Noninvasive IPL therapy with MGX statistically improved not only dry eye symptoms but also tear film assessments.

Sinkhole flooding is an essential hydrological process to recharge karst aquifer in arid to dry sub-humid regions. On the other hand, the increase of rain extremes is one of the major consequences of the global warming, together with the expansion of drylands. Thus, appropriate runoff regulation in endorheic karst basins in order to reduce the risk of flooding and improve the quantity and quality of the water drained by sinkholes will be more and more crucial. With these premises, a systematic review was performed by using WoS engine to infer the best practices for the karst water management in regions actually or potentially affected by water scarcity. Hydrological models are essential to manage the consequences of climate change on karst water resource, however the review shows that providing the tools necessary for reliable modeling is still challenging. Finally, due to the intrinsic vulnerability of the karst aquifers, pollution reduction and wastewater recycling policy will play key role in the next decades.

The WASP-Index is computed over Iberia for three monthly timescales in 1961-2020, based on an observational gridded precipitation dataset (E-OBS), and in 2021-2070, based on bias-corrected precipitation generated by a six-member climate model ensemble from EURO-CORDEX, under RCP4.5 and RCP8.5. The WASP performance in identifying extremely dry or wet events, reported by the EM-DAT disaster database, is assessed for 1961–2020. An overall good agreement between the WASP spatial patterns and the EM-DAT records is found. The areolar mean values revealed an upward trend in the frequency of occurrence of intermediate-to-severe dry events over Iberia, which will be strengthened in the future, particularly for the 12m-WASP intermediate dry events under RCP8.5. Besides, the number of 3m-WASP intermediate-to-severe wet events is projected to increase, mostly the severest events under RCP4.5, but no evidence was found for an increase in the number of more persistent (12m-WASP) wet events under both RCPs. Despite important spatial heterogeneities, an increase(decrease) of the intensity, duration, and frequency of occurrence of the 12m-WASP intermediate-to-severe dry(wet) events is found under both scenarios, mainly in the southernmost regions of Iberia, thus becoming more exposed to prolonged and severe droughts in the future, corroborating the results from previous studies.

There is sufficient knowledge of the beneficial effect of warm-dry storage on breaking the morpho-logical dormancy of the chincuya (Annona purpurea Moc. & Sessé ex Dunal) seed embryo. Chincuya is an underutilized, tropical wild species native to Mexico, with potential as a biopesticide. The impact of warm-dry storage and gibberellic acid treatment on seed viability and germination was determined to improve that knowledge further. Also, the content and kinetics of fatty acids in chincuya seeds were profiled during warm-dry storage. Seed treatments included storage time (0, 3, 6, 9, and 12 months), seed imbibition for 72 h in gibberellic acid at 350 mg L-1, and distilled water im-bibition for 72 h for the control treatment. Seed viability was determined using the TTZ classic test. Imbibed seeds were germinated on paper towels and incubated at 30 °C during the day and 25 °C at night in a 12:12 h dark:light photoperiod. The lipid profile was obtained by gas chromatography. During the storage treatment, seeds stayed in darkness at 25 ± 3 °C. Results showed that high viability remained up to month 9 in storage when it significantly decreased. Freshly harvested seeds germi-nated at a statistically significantly lower rate (26.1 %) than six-month-old seeds (65.6 %). The profile of fatty acids breaks down as palmitic acid (33.41 %), stearic acid (7.72 %), and arachidic acid (1.30 %), for a total of 42.44 % of saturated fatty acids. The detected unsaturated fatty acids (52.15 %) were palmitoleic acid (1.52 %), oleic acid (43.37 %), and linoleic acid (7.24 %). No significant changes were detected in fatty acid content; however, the highest fatty acid content (92.84 %) occurred with the highest germination rate. Regression analysis showed significant content changes: palmitoleic and palmitic acid increased while oleic acid decreased during dry storage. Arachidic acid showed a slight downward trend. Also, fatty acid content significantly differed between intact seeds (unstored and unincubated) and latent seeds (unstored, incubated, and ungerminated). The total fatty acids content for latent seeds was significantly lower. These results show that Annona purpurea seeds present morphophysiological dormancy. Also, we document the highest germination rate reported (65.6 %) and report the presence of arachidic and palmitoleic acids in chincuya seeds.

In the article, were checked influences of microaeration, pH, and VSS (Volatile Suspended Solid) for sour cab-bage anaerobic digestion. Results fermentation of sour cabbage under the condition of small oxygen addition are presented in this research can be classified as dark fermentation or hydrogenotrophic anaerobic digestion. The investigations were carried out for two concentrations 5 g VSS /L and 10 g VSS /L of sour cabbage at pH 6.0. The oxygen flow rates (OFR) for 5 g VSS /L were in the range of 0.53 to 3.3 mL/h for obtaining 2% to 8% of oxygen. In cases of low pH and microaeration, ethylene production was observed at a level below 0.05% in biogas. The highest volume of hydrogen for 5 g VSS/L was obtained for flow rate 0.58 O2 mL/h, giving hydrogen concentration in biogas in the range of 0 to 20%. For VSS 5 g/L and oxygen flow rate 0.58 mL/h; 0.021 L of hydrogen is produced per gram of VSS. In this case, VSS 10 g/L and oxygen flow rate 1.4 mL/h at pH 6.0, 0.03 L of hydrogen is generated per gram. Microaeration from 0.58 mL/h to 0.87 mL/h was propitious for hydrogen production at 5 g VSS/L of sour cabbage and 1.4 mL/h for 10 g/L. Another relevant factor is the volatile suspended solid factor of sour cabbage that caused optimal hydrogen production at VSS 89.32%.

Modern day civilization is dependent on energy generation by fossil fuels. But the major drawback of using fossil fuels is environmental pollution. Microalgae are potential candidate for production of various products of interest, such as proteins, mini food, pigments and triglycerides that can be converted into biofuels. Lignocellulosic feedstocks are the most abundantly available raw material of plants that can serve as a promising feedstock for cultivating bacteria, fungi, yeasts and microalgae to produce biofuels and other value-added products. Owing to the abundant availability of these low/no cost substrates, can be utilized as feedstocks for cultivating microalgae to generate biogas/biodiesel. Likewise, there is much room to exploit defatted algal biomass to be used as animal/fish feed and oil producing/accumulating genes knowledge in future to produce high and good quality biodiesel and biogas.

Protein malnutrition is present in developing countries but also in developed ones, due by the actual eating habits with insufficient protein intake, in addition to this it is estimated by the Food and Agricultural Organization of the United Nations an increase of world population of 9.1 billion people in less those 30 years, posing the challenge of nourish the mankind. There are different strategies to afford this challenge, one of the most promising ones is to approach novel protein sources like plants, microorganisms, and insects from dry lands.

Extreme climates such as droughts and hot extremes, may result in marked damage to crop yields and threaten regional and global food security. Maize is a major grain crop in Liaoning Province, severely affected by drought and hot events. The objective of this study is to advance an approach to estimate the risk of crop yield reduction under the compound dry-hot events (CDHE) in Liaoning Province. Results show that the ratio of stations experiencing compound dry-hot events during the twelfth leaf and maturity stage tended to increase on the time scale. On a spatial scale, the frequency of compound dry-hot events in central Liaoning Province was relatively low during the whole and various reproductive periods of maize. In addition to the twelfth leaf, western Liaoning Province is prone to compound dry-hot events. The high-risk area for the occurrence of the compound dry-hot events in maize is Chaoyang City, located in the western part of Liaoning Province, and the cities in the low-risk area account for about 64.3% of the total number of cities in Liaoning Province, mainly in the central and northern parts of Liaoning Province. Generally, this study emphasizes focusing on the impacts of compound dry-hot events on agricultural production and provides an index to assess the risk of compound dry-hot events on maize production.

The application of dry lubrication in rolling contacts is challenging due to wear. In previous studies graphene platelets applied as dry lubricants on the surfaces of angular contact ball bearings demonstrated superior properties. These specific bearings, experiencing both rolling and spinning motion, create more severe conditions for dry lubricants. The applied graphene platelets have a thickness of few graphene layers in the nm range and a diameter in the µm range. Such platelets can be produced by mechanical exfoliation from graphite. To delve deeper into the lubrication effects, investigations were carried out using a milli tribometer. In the tests, a fixed steel ball is sliding against an oscillating counterpart under defined load. During the measurements, the applied load and tangential forces on the ball are recorded to calculate the friction. In our case, a steel ball with a diameter of 6 mm was used against graphene-based films on flat bearing surfaces (axial bearing washer). Comparative investigations included nano graphite particles and fullerene as dry lubricants, in addition to graphene platelets of various staple thicknesses. To increase the adhesion of the films to the surfaces, a pre-rolling process was implemented. Afterwards, the friction on the compressed films was measured. The results indicate that the pre-rolling process effectively reduces the friction of the system. After testing, the surfaces underwent analysis using laser scanning microscopy to assess the formed films, wear, and material transfer. It has been demonstrated that the pre-rolling process leads to the formation of a very thin compacted film with surface protective properties. On the ball as counterpart, the graphene platelets generate a transfer film on the contacting surface.

The heat generated during the startup process of dry gas seals, such as the friction heat of the asperities, viscous shear heat, and the expansion heat of the gas film, easily leads to seal failure and endangers the stable operation of turbomachinery. This study combines the statistically modified contact model and the average Reynolds equation by considering the adiabatic index and the microscale effects of dry gas seals to explore the heat generation characteristics of dry gas seals formed in series at multiple times. In particular, the change laws and influencing factors among the components, including the friction heat of asperities and the shear heat and expansion heat of the gas film and total heat, are investigated. A comparative analysis indicates that the slip flow effect increases the total heat during the startup process. The friction heat is much greater than expansion heat and shear heat. Despite constant acceleration, exponential acceleration, or Harrision acceleration, the heat changes are uneven during the startup process. In particular, the heat changes sharply in the early stage and gently in the later stage. The Harrision acceleration mode is the most conducive to sealing stability.

Fusarium dry rot is one of the major postharvest potato diseases of during storage after harvest, which not only results in quality degradation but also brings up huge economic losses. The dis-ease can be elicited by some species of Fusarium, the pathogenic fungi of Fusarium causing potato dry rot are considerably diverse in various countries and regions. Fusarium spp. infection is as-sociated with dry rot produce mycotoxins, which has phytotoxicity and mycotoxicoses on hu-mans and animals. Chemical synthetic fungicide is considered as the main control measure to Fusarium dry rot of potato, nevertheless, it is unfortunate that the persistent application inevitably results in the emergency of resistant strain and environmental contamination. A comprehensive disease control strategy includes potato cultivar selection, appropriate cultural practices (crop rotation, cultivate pattern, fertilization, and irrigation), harvesting process and postharvest treatment (harvesting, classification, packaging, wound healing), storage condition (environ-mental disinfection, temperature, humidity and gas composition) along with the application of fungicide pre-harvest or postharvest. Recently, emerging studies indicated that eco-friendly strategies include physical control, chemical methods (such as the application of generally rec-ognized as safe (GRAS) compounds or chemical (elicitors) and biological control have been in-troduced to combat Fusarium dry rot of potato.

Biowaste management is in the center of attention in recent years, due to the increased focus on Circular Economy practices. Recent management solutions promote exploration for small and medium scale processing and monitoring practices. In this context, two pathways of biowaste valorization are analyzed: composting and anaerobic digestion. This study focuses on energy production with the hydrothermal carbonization (HTC) of anaerobic residues from biogas production. Lesvos has numerous processing facilities and olive mills, and therefore Olive Mill Wastewater (OMWW) are the main biowaste streams in the island, along with olive tree pruning, the organic fraction of municipal solid waste and sludge from wastewater treatment facilities. Most studies present applications on specific types of biowaste, while this study aims to co-treat several biowaste streams. A holistic experimental set-up that combines aerobic and anaerobic treatment strategies was developed taking into consideration the hydrothermal treatment of AD digestate along with locally available biowaste, like OMWW, sludge etc. A main target objective is to investigate if solid fraction could have a high heating potential In addition, HTC was able significantly to reduce the COD of OMWW while resulting in hydrochars with increased heating values.

Ventricina del Vastese is a traditional dry fermented sausage from Central Italy not yet charac-terized for occurrence, identity and safety of coagulase negative staphylococci (CNS), a bacterial group technologically important for this kind of products. Therefore, in this study, 98 CNS isolates from four manufacturers were differentiated by Repetitive element palindromic PCR (Rep-PCR) and identified by 16S rRNA gene sequencing. These were examined for genes encoding biogenic amine (BA) production, resistance to aminoglycosides, β-lactams and tetracyclines and staphylococcal enterotoxins (SEs). Staphylococcus succinus (55%) predominated, followed by S. xylosus (30%), S. epidermidis (7.4%), S. equorum (3.1%), S. saprophyticus (3.1%) and S. warneri (1%). One S. succinus subsp. casei isolate was slightly β-hemolytic. SEs and the histidine decarboxylase gene hdcA were not detected, while the tyrosine decarboxylase gene tdcA was detected in four S. xylosus isolates. A blaZ beta-lactamase gene and tetracycline resistance genes tetK (six isolates) and tetA (one isolate also bearing tetK) were found, respectively. However, fewer hazardous and AR traits compared to CNS examined in other studies were found, as a probable consequence of using meat from animals reared in conditions that allow to minimize pathogen circulation and antibiotic use. Therefore, appropriate production conditions can reduce these threats.

The quality of waste activated sludge produced in urban wastewater treatment systems varies according to the efficiency of the operation of treatment units along the content of microflora and organic carbon. However, these represent a biogas-energy alternative through anaerobic co-digestion, contributing to reducing the environmental impacts caused by their inadequate disposal. Biogas production by the Two-stage production method in batch digesters was evaluated by two qualities of waste activated sludge (SLB50 y SLB90) and with a mixture of two co-substrates: cattle manure (CEV50 y CEV90) and residual edible oil with mixing, pH and temperature control. Bacteria in good quality sludge (SLB90) showed a faster adaptation of 2 days than those in low quality (SLB50) with 25 days lag phase. The highest CH4 production was for SLB90 (303.99cm3 d-1) compared to SLB50 (4.33 cm3 d-1); while cow manure sludge mixture (CEV90) contributed to increasing production of CH4 (42 422.8 cm3 d-1) compared to CEV50 (12 881.45 cm3 CH4 d-1), while in residual edible oil mixture they were 767.32 cm3 d-1 and 211.42 cm3 d-1 for CAV90 y CAV50, respectively. The addition of sludge co-substrates improves the nutrient balance, C/N rate and micro flora diversity; consequently methane production improves too; this methodology could be integrated into concepts of Circular economy.

Using a wide range of organic substrates in the methane fermentation process enables efficient biogas production. Nonetheless, in many cases, the efficiency of electricity generation in biogas plant cogeneration systems is much lower than expected, close to the calorific value of the applied feedstock. This paper analyses energy conversion efficiency in a 1 MWel agricultural biogas plant fed with corn silage or vegetable waste and pig slurry as a feedstock dilution agent, depending on the season and availability. Biomass conversion studies were carried out for 12 months, during which substrate samples were taken once a month. The total primary energy in substrates was estimated in laboratory conditions by measuring the heat of combustion in a ballistic bomb calorimeter (17,760 MWh·year-1), and in the case of pig slurry, biochemical methane potential (BMP, (201.88±3.21 m3·Mg VS-1). Further, the substrates were analysed in terms of their chemical composition — from protein, sugar and fat content to mineral matter determination, among other things. The results obtained during the study were averaged. Based on such things as the amount of biogas produced at the plant, the amount of chemical (secondary) energy contained in methane as a product of biomass conversion (10,633 MWh·year-1) was calculated. Considering the results obtained from the analyses, as well as the calculated values of the relevant parameters, biomass conversion efficiency was determined as a ratio of chemical energy in methane to (primary) energy in substrates, which was 59.87%, as well as electricity production efficiency, as a ratio of electricity produced (4,913 MWh·year-1) to primary energy, with a 35% cogeneration system efficiency. Full energy conversion efficiency, related to electricity production, reached a low value of 27.66%. This article provides an insightful, unique analysis of energy conversion in an active biogas plant as an open thermodynamic system.

The use of the commercial simulator Aspen Plus® could bring an amelioration in the accuracy of the predictions of the chemical species composition in the output streams of the anaerobic digestion process, due to availability of a broad library of thermodynamic and phenomena transport properties in this commercial package. In the present investigation, the process simulation model for anaerobic digestion, which was originally developed by Rajendran et al. [1], has been modified by including a stoichiometric-equilibria reactor to calculate the extent of the ionization of the molecules present in the anaerobic digestate. The refined model offers a more accurate prediction of the composition of the biogas because it delves on the chemical equilibrium of the gaseous stream and the anaerobic digestate. Additionally, the refined model allows to assess the possibility of upgrading the gaseous stream to biomethane degree via manufacturing of ammonium bicarbonate. This processing pathway relies on the stabilization of the anaerobic digestate by means of biomass ash-based treatment. First of all, the titration of the manure digestate with the hydrochloric acid showed that a dose of 3.18 mEq/g would be required to attain the targeted pH of zero-point charge, upon addition of the sewage sludge ash in a ratio to the manure digestate of 0.6 ± 0.2 %. Secondly, the profiles of ammonia, carbon dioxide, and methane found in the biogas agree with both the pH of the treated digestate and the processes described in for the simultaneously upgrading the biogas and the production of ammonium bicarbonate. The refined Aspen Plus® model presented in this article needs to be further developed to ensure the standards are attained in all output streams of stabilized anaerobic digestate, biomethane, and isolated added-value chemical fertilizers.

Biogas contains more than 40% CO2 that can be removed to produce high quality CH4. Recently, CH4 production from CO2 methanation has been reported in several studies. In this study, CO2 methanation of biogas was performed over a 20 wt% Ni-Mg-Al catalyst, and the effects of CO2 conversion rate and CH4 selectivity were investigated as a function of CH4, O2, H2O, and N2 compositions of the biogas. At a gas hourly space velocity (GHSV) of 30,000/h, the CO2 conversion rate was ~79.3% with a CH4 selectivity of 95%. In addition, the effects of the reaction temperature (200–450 °C), GHSV (21,000–50,000/h), and H2/CO2 molar ratio (3–5) on the CO2 conversion rate and CH4 selectivity over the 20 wt% Ni-Mg-Al catalyst were evaluated. The characteristics of the catalyst were analyzed using Brunauer-Emmett-Teller (BET) surface area analysis, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM). The catalyst was stable for approximately 200 h at a GHSV of 30,000/h and a reaction temperature of 350 °C. CO2 conversion and CH4 selectivity were maintained at 75% and 93%, respectively, and the catalyst was therefore concluded to exhibit stable activity.

The popular appreciation of dry white wines is most frequently directed to young wines. However, present consumption trends comprise the valorisation of aged dry white wines. Therefore, the present work was aimed at the sensory analysis of these wines with different ages to define their sensory space and to understand which factors drive their quality evaluation by experienced tasters (critics, oenologists and students). Individuals were asked to evaluate several synthetic and aesthetic attributes and to characterise the analytic sensory profile through a Check-All-That-Apply (CATA) methodology. The quality evaluations were differently correlated with wine synthetic parameters according to the taster group. For both critics and oenologists, overall quality scores were driven by persistence and complexity. Moreover, quality was also highly correlated with power for critics and with balance for oenologists. Quality scores were highly correlated with wine browning (absorbance at 420 nm) for critics. The tasting panel showed a homogeneous analytic description of aroma, taste and mouthfeel consistent with wine age. The different ages could be associated to a continuous sensory space characterised by a decreasing perception of freshness and increase in mature and mellowed descriptors. All wines shared an austere in-mouth perception elicited by their acidity, saltiness, bitterness, smoothness and dryness. The age prediction showed that most tasters failed to guess the age wines with more than roughly 13 years old, indicating that tasters were not familiar with the sensory features of white wines with 17 to 46 years old. In conclusion, experienced tasters consistently described the sensory space and recognised the high quality of aged dry white wines. Education programs may use the defined sensory spaces according to aging and to expand the range of quality perception by consumers.