This paper presents a comprehensive evaluation of metal foam employment within polymer electrolyte fuel cells (PEFCs) and compares it with conventional serpentine channels from both experiment viewpoints and computational fluid dynamics simulation. The experiments are designed to study the effects of material, area density, compression ratio, and final thickness of metal foam. Additionally, the influence of housing plate material and relative humidity (RH) is also tested for the first time. The results reveal that at RH=75-100%, the best distributor design is nickel foam with a compression ratio of 70%, a final thickness of 0.5mm, and SS-304 housing plate, which delivers 3110 mA cm^-2 as limiting current density that is scarce in the literature. The PEFC with this foam distributor shows a 10% improvement in maximum power density and 45% in limiting current density compared to the serpentine channel case. While at RH=30%, the same foam flow field with a final thickness of 1mm is a superior option. The experiments also indicate that maximum power density increases by 23% as the compression ratio rises from 0 to 70%, while reducing final thickness from 1 to 0.5 mm causes a 19% enhancement in cell performance. Simulation results reveal that metal foam is more successful in evenly reactant distribution so that the average oxygen mass fraction at the cathode catalyst layer is increased by 38% in the metal foam case compared to the serpentine channel.

A new three-dimensional numerical model of a polymer electrolyte fuel cell (PEFC) with a single straight channel has been developed to primarily investigate the important impact of the double-sided microporous layer (MPL) coating on the overall performance of the fuel cell and the distribution of the current and the oxygen concentration within the cathode gas diffusion layers (GDLs). Realistic experimentally estimated interfacial contact resistance values between the gas diffusion layer and each of the bipolar plates and the catalyst layer values were incorporated into the model, and parametric studies were performed. The results showed that the double-sided MPL coating could significantly improve the fuel cell performance by up to 30%. Also, it was shown that the neglect of the contact resistance between the MPL and the catalyst layer could overestimate the fuel cell performance by up to 6%. In addition, the results showed that the fuel cell performance and the distribution of the current and oxygen are more sensitive to the porosity of the MPL facing the bipolar plate than the porosity of the MPL facing the catalyst layer. All the above results are presented and critically discussed in detail.

The optimized design of catalyst layer (CL) plays a vital role to improve the performance of polymer electrolyte membrane fuel cells (PEMFCs). The need to improve transport and catalyst activity is especially important at low Pt loading, where local oxygen and ionic transport resistances decrease the performance due to an inevitable reduction of active catalyst sites. In this work, local oxygen and ionic transport are analyzed using direct numerical simulation on virtually reconstructed microstructures. Four morphologies are examined: (i) heterogeneous, (ii) uniform, (iii) uniform vertically-aligned, and (iv) meso-porous ionomer distributions. The results show that the local oxygen transport resistance can be significantly reduced, while maintaining good ionic conductivity, through the design of high porosity CLs (ε≃0.6−0.7) with low agglomerated ionomer morphologies. Ionomer coalescence into thick films can be effectively mitigated by increasing the uniformity of thin films and reducing the tortuosity of ionomer distribution (e.g., good ionomer interconnection in supports with a vertical arrangement). The local oxygen resistance can be further decreased by the use of blended ionomers with enhanced oxygen permeability and meso-porous ionomers with oxygen transport routes in both water and ionomer. In summary, achieving high performance at low Pt loading in next-generation CLs must be accomplished through a combination of high porosity, uniform and low tortuosity ionomer distribution, and oxygen transport through activated water.

The blended perfluorinated sulfonic acid ionomers are prepared to have equivalent weight (EW) ~1000, 980, and 830. The catalyst layers (CLs) using blended PFSA ionomers with different side chain lengths and EWs are investigated, compared to the CLs utilizing single ionomers. The IEC results indicate that the blended ionomers have the targeted EWs. As a result, it is found that the blended ionomers exhibit higher ion conductivity than the single ionomers at all temperatures due to higher water uptake of the blended ionomers. Even though they have a similar EW, it implies that the blended ionomers have bulk structure to form competent free volume. The blended ionomers with short side chain (SSC) and low EW can help reduce the activation energy due to the enhanced hydrophobic and hydrophilic segregation. In addition, it is observed that the catalyst layers using the blended ionomer form more porous microstructure to help reduce the resistance of oxygen transport and attributes to lower mass transfer loss. This effect is significantly revealed in the fuel cell operation at not the lower temperature (70 °C) and full humidification (100%) but the elevated temperature (80 °C) and lower relative humidity (50 and 75%). The blended ionomer-based catalyst layers with higher water uptake and porous CL structure result in higher fuel cell performance and better mass transport than the single ionomer-based catalyst layers.

Based on literature data, an analysis was conducted on the thermodynamic and kinetic dependencies of the thermal decomposition of methane. Course of this process was analysed for both thermal and thermal-catalytic conditions. The elementary reaction, i.e. the synthesis of methane from its elements, including its reversibility, was used as the basis for the for considerations on the kinetic model. The conversion degree was adopted as the kinetic parameter (kinetic variable) since this measure is essential for determining the amount of carbon deposit formed and thus closing the mass balance of this process. Several different kinetic models for the elementary reaction were analysed to determine how do they relate in regard to the constant of the reaction rate. It was determined that regardless of whether the process is catalytic or purely thermal, for temperatures t>900°C, the influence of reversibility of the reaction, has negligible influence on the yield of hydrogen produced, and thus can be omitted from the kinetic models. Special attention was given to iron-based catalysts, analysing the reactivity of Fe/C systems. It was demonstrated that the determined kinetic parameters satisfy the Kinetic Compensation Effect (KCE). Furthermore, by incorporating elements of Transition State Theory (TST), the existence of Entropy-Enthalpy Compensation (EEC) was highlighted. Based on these findings Authors show that through analysis of the changes in activation energy (E=20–421 kJ·mol-1) only an estimate of the optimal process conditions can be found, because the isoconversional temperature is also dependent on the way in which the reaction is conducted (T_{iso}=1200-1450K\ >\ \ T_{eq}). In other words, it was found that strong influences of such factors as T, P, etc. can locally compensate each other. Finally, it was also shown that the relations between KCE and EEC complement each other, which is confirmed by the determined average activation entropy at the isokinetic temperature (∆SB= -275.0 J·(mol·K)-1).

In order to establish the formation patterns of the Co–Mg oxide system, samples with different Co:Mg ratios and heat treatment temperatures were synthesized and studied. Study of the sam-ples confirmed the phase transition of MgxCo2–xO4 spinels into corresponding solid solutions at 800–900 °C. The similarity of formation patterns for different compositions is shown. The rock-salt oxide in low-temperature samples is an anion-modified paracrystalline phase that forms a “true” solid solution only upon spinel decomposition. TPR profiles of decomposed Co3O4 spinel show surface Co3O4 peaks and a wide peak corresponding to well-crystallized CoO, while par-tial Co3O4 TPR up to 380 °C results in dispersed and amorphous CoO. High-temperature non-stoichiometric samples are poorly reduced, indicating their low oxygen reactivity. Spinel reoxidation after heat treatment to 1100 °C by calcination at 750 °C showed complete regenera-tion for MgCo2O4–Co3O4 samples and its absence in case of an excess of MgO relative to stoi-chiometry. Based on the data obtained, it can be concluded that the processes governing the formation of Co–Mg oxide systems are determined by both Co:Mg ratio and the heat treatment conditions, potentially providing the possibility of fine tuning for specific catalytic processes.

Polymer Electrolyte Membrane Fuel Cells (PEMFCs) have emerged as a pivotal technology in the automotive industry, significantly contributing to the reduction of greenhouse gas emissions. The high material costs of the gas diffusion layer(GDL) and bipolar plate(BP) creates a barrier for large scale commercial application. This study aims towards addressing this challenge by optimizing the material and design of the cathode, GDL and BP. While Deterministic design optimization(DDO) methods have been extensively studied, they often fall short when manufacturing uncertainties are introduced. This issue is addressed by introducing Reliability based design optimization(RBDO) to optimize four key PEMFC design variables i.e., δ_gdl, d_ch, w_ch, and w_land. The objective is to maximize cell voltage(V_cell) considering material cost of cathode gas diffusion layer(Cost_cGDL), and cathode bipolar plate(Cost_cBP) as reliability constraints. Results of the DDO show an increment in V_cell of 31mV, with reliability of around 50% for Cost_cGDL and Cost_cBP. In contrast RBDO method provides a reliability of 95% for both Cost_cGDL and Cost_cBP.

Demand for environmentally friendly types of energy is growing all over the world, which naturally increases the intensity of work on the production of hydrogen-containing fuel mixtures. Steam reforming of methanol is one of the most effective areas of research, as it is a process with low energy consumption. The results of steam reforming of methanol on the catalysts prepared by solution combustion synthesis (SCS) and impregnation by moisture capacity are presented. Investigation of the activity of Cu-Ce-Al catalysts of different composition was carried out for production of hydrogen and comparison of SCS with traditional impregnation method. Methanol conversion reaches 99%, while the selectivity of H2 was 88%, at 500 °C. It was found that CuAl2O4 spinel formation is due to substitution of Al3+ with Cu2+ Ce3+ cations. A consequence CuAl2O4 and CeAlO3 lattice parameters increase because of difference in ionic radius of Al3+ (0.53 Å) and Cu2+ (0.73 Å), Ce3+ (1.07 Å). Advantages of SCS catalysts in steam reforming of methanol were shown. The aim of this research is to develop a new catalyst for conversion of methanol into hydrogen containing fuel mixtures, which will further promote the organization of a new era of environmentally friendly energy-saving production methods.

Intermediate temperature solid oxide fuel cell (SOFC) operation provides numerous advantages such as high combined heat and power (CHP) efficiency, potentially long-term materials stability, and the use of low-cost materials. However, due to the sluggish kinetics of the oxygen reduction reaction at intermediate temperature, the cathode of SOFC requires an efficient and stable catalyst. Significant progress in the development of cathode materials has been made over recent years. In this article, multiple strategies for improving the performance of cathode materials have been extensively reviewed such as A and B site doping of perovskites, infiltration of catalytic active materials, the use of core-shell composites, etc. Emphasis has been given to intrinsic properties such as thermal expansion compatibility, chemical and thermal stability, and oxygen transport number. Furthermore, to avoid any insulating phase formation at the cathode/electrolyte interface, strategies for interfacial layer modifications have also been extensively reviewed and summarized. Based on major technical challenges, future research directions have been proposed for efficient and stable intermediate temperature solid oxide fuel cell (SOFC) operation.

Herein, we present preparation of solid polymer electrolyte (SPE) comprising of PEO, NaPF₆ and varying fraction of Succinonitrile (SN) by standard solution cast technique. The morphological features and structural properties were studied by the FESEM, XRD, respectively. FTIR was performed to study the interactions between polymer host, salt, and SN. Impedance spectroscopy, Transference number measurements, LSV and CV were used to examine the electrochemical properties. The complex permittivity/conductivity & modulus were studied to understand the dielectric properties by evaluating the dielectric strength, relaxation time, hopping frequency and dc conductivity. Based on the experimental results an interaction mechanism is presented.

Despite polycarbonate (PC) being a widely used engineering plastic, its notch and crack sensitivity pose challenges in critical applications. To address this, PC was blended with elastomeric polymers to explore the improvement in toughness. This study systematically investigates the toughening mechanisms of PC blended with acrylonitrile-butadiene-styrene (ABS), copolyether ester elas-tomer (COPE), and ABS and styrene-ethylene-butylene-styrene (SEBS) copolymer grafted with maleic anhydride (MA). The morphology and mechanical behavior were evaluated under qua-si-static and high-speed tensile tests and Charpy impact tests using optical, electronic, and atomic force microscopy and Raman spectroscopy. The morphological analysis reveals cavitation and crazing phenomena for COPE and SEBS-g-MA systems, and mostly debonding for ABS, indicating an improvement in toughening. While the addition of ABS improves the PC plastic deformation, modifying ABS with maleic anhydride enhances the elastic modulus. Blending PC with SEBS-g-MA increases the strain at break, and the addition of COPE significantly improves the deformation behavior of PC (by around 115%). This comparative study provides valuable insights into the performance of different PC-elastomer blends under similar conditions, supporting the selection of appropriate materials for given applications.

The article offers a comprehensive overview of recent breakthroughs in eco-friendly polymers and polymer composites, underscoring their pivotal role in addressing sustainability challenges across diverse industrial sectors. Despite encountering obstacles related to performance and processability, biopolymers sourced from renewable materials emerge as promising alternatives for the plastics that are currently used by human beings. Natural fillers are highlighted as a strategic avenue for crafting sustainable composites, with residual natural fillers being particularly explored. Heightened environmental concerns propel discussions on the criticality of integrating biodegradable materials with natural fillers, underlining the urgency for clear frameworks and financial incentives to support adoption of these materials. Additionally, the article examines the potential of biodegradable polymers and polymer composites, with a specific emphasis on the utilization of polyhydroxyalkanoate (PHA) in composite materials and its market prospects. Moreover, it emphasizes the indispensable need for ongoing research and development endeavors to address environmental challenges within the polymer sector, reflecting a mounting interest in sustainable materials across industries.

Li⁺-conducting polyethylene oxide-based membranes, incorporating the N-butyl-N-methylpyrrolidinium bis(trifluoromethanesulfonyl)imide, are as electrolyte separators for all-solid-state lithium polymer batteries operating at medium-high temperatures. The incorporation of the ionic liquid remarkably improves the thermal, ion-transport and interfacial properties of the polymer electrolyte, which, in combination with the wide electrochemical stability even at medium-high temperatures, allow high current rates without any appreciable lithium anode degradation. Battery tests carried out at 80 °C have shown excellent cycling performance and capacity retention even at high rates, never tackled by ionic liquid-free polymer electrolytes. No dendrite growth onto the lithium metal anode was observed.

In this study a material based on Polyethylene (PE) and Microcrystalline Cellulose (MC) was developed as a breathable packaging film. Surface functionalization of MC with 3 aminopropyltriethoxysilane (APTES) shows to be an efficient alternative to tailor their properties and increase opportunities for the application of MC on the reinforcement of polymers such polyethylene (PE). Functionalization of MC with mentioned silane derivative was achieved using a green method and later used on the development of composites with PE in three percentages (1, 3 and 5%). All the materials were prepared by melt blending and characterized, in terms of structural properties (ATR-FTIR and FTIR in transmittance, EDX, SEM), thermal properties (DSC and TGA), thermomechanical properties (DMA), contact angle measurements and permeability to oxygen and water vapor. The materials demonstrated to have potential to be used as breathable film packaging of fresh products.

Dehydration of hydrogen gas is one of the important steps in many industrial purposes thus, drying systems have been developed with high-efficiency and relative effect. In this article, the basic principles and design of a three-bed TSA (Temperature Swing Adsorption) dryer for dehydration operation of hydrogen gas drying are described in detail. The text commences with an in-depth explanation of the basic principles behind TSA technology such as adsorption and desorption mechanisms, thermodynamic considerations and material selection for adsorbents. This paper also deals with the detailed design of a three-bed TSA dryer, explaining about various fabricating details that influences both performance and total operability. The third part focuses the operational phase, and especially in cycle time, regeneration strategy and efficiency of energy. Advanced optimisation techniques are employed to lower energy consumption, increase throughput capacity and improve overall system. This detailed study will be of great help for engineers and investigators working on TSA systems design and optimization to dehydrate hydrogen gas, contributing towards the betterment in this important field dealing with industrial gas processing.

As marine traffic is contributing to pollution and mostly have predictable route with repetitive load profiles, to reduce their impact on environment, hybrid system with proton exchange membrane fuel cells (PEMFC-s) and battery pack, is promising replacement. For this purpose, the numerical model of repowered existing vessel that have two diesel engines with 300 kWe is developed. The goal of this paper is to develop numerical model which analyzes and determine equivalent hybrid ship propulsion system for known traveling route. The developed numerical model consists of an interconnected system with PEMFC stack and battery pack as power sources. Numerical model is developed and optimized to meet minimal required power demand for successful route demand, which has variable loads and daily sails six-time same voyage- in total 54 nautical miles. The results have shown that equivalent hybrid power system consists of 300 kWe PEMFC stack and battery pack with 424 kWh battery and state of charge varying between 20 and 87%. To power this new hybrid power system, hydrogen tank of 7200 l holding 284.7 kg at pressure of 700 bar is needed, compared to previous system that spend 1524 kg of diesel and generate 4886 kg of CO2.

Redox mediators comprising I–, Co3+, and Ti3C2Tx MXene were applied to dye-sensitized solar cells (DSCs). In the as-prepared DSCs (I-DSCs), wherein hole conduction occurred via the redox reaction of I−/I3− ions, the power conversion efficiency (PCE) was not altered by the addition of Ti3C2Tx MXene. The I-DSCs were exposed to light to produce Co2+/Co3+-based cells (Co-DSCs), wherein the holes were transferred via the redox reaction of Co2+/Co3+ ions. A PCE of 9.01% was achieved in a Co-DSC with Ti3C2Tx MXene (Ti3C2Tx-Co-DSC), which indicated an improvement from the PCE of a bare Co-DSC without Ti3C2Tx MXene (7.27%). It was also found that the presence of Ti3C2Tx MXene in the redox mediator increased the hole collection, dye regeneration, and electron injection efficiencies of the Ti3C2Tx-Co-DSC, leading to an improvement in both the short-circuit current and the PCE when compared with those of the bare Co-DSC without MXene.

The aim of this work is research dedicated to the search for new bactericidal systems for use in cosmetic formulations, dermocosmetics, or the production of wound dressings. Over the last two decades chitosan due to its special biological activity, has become a highly indispensable biopolymer with very wide application possibilities. Literature reports on the antibacterial effects of chitosan are very diverse, but our research has shown that they can be successfully improved through chemical modification. Therefore, in this study, results on the synthesis of new Schiff bases chitosan – dCsSB-SFD and dCsSB-PCA obtained using two aldehydes: sodium 4-formylbenzene-1,3-disulfonate (SFD) and 2-pyridine carboxaldehyde (PCA) respectively. Chitosan derivatives synthesized in this way demonstrate stronger antimicrobial activity. Carrying out the procedure of grafting chitosan with a caproyl chain allowed obtaining compatible blends of chitosan derivatives with κ-carrageenan, which are stable hydrogels with a high swelling coefficient. Furthermore, covalently bounded PCL improved the solubility of obtained polymers in organic solvents. With this respect, the Schiff base-containing polymers obtained in this study, with special hydrogel and antimicrobial properties are very promising materials for the potential use as a controlled-release formulation of both, hydrophilic and hydrophobic drugs in cosmetic products for skin health.

The aim of this study was utilization of ground tea waste (GT) left after brewing the black tea as a biofiller of natural rubber (NR) composites. Ionic liquids (ILs), i.e., 1-ethyl-3-methylimidazolium lactate and 1-benzyl-3-methylimidazolium chloride, often used to extract phytochemicals from tea, were applied to improve the dispersibility of GT particles in elastomeric matrix. The influence of GT loading and ILs on curing characteristics, crosslink density, mechanical properties, thermal stability and resistance of NR composites to thermo-oxidative aging was investigated. The amount of GT did not significantly affect curing characteristics and crosslink density of NR composites, but had serious impact on tensile properties. Applying 10 phr of GT improved the tensile strength by 40% compared to unfilled NR. Further increasing in GT content worsened the tensile strength due to the agglomeration of biofiller in elastomer matrix. ILs significantly improved the dispersion of GT particles in elastomer and increased the crosslink density by 20% compared to the benchmark. Owing to the poor thermal stability of pure GT, it reduced the thermal stability of vulcanizates compared to unfilled NR. Most importantly, GT-filled vulcanizates showed improved resistance to thermo-oxidative aging, since the aging factor increased by 25% compared to the unfilled vulcanizate.

Pt modified BaZr_0.76Y_0.2Ni_0.04O₃ (BZYN) is fabricated and characterized as a stable electrolyte for proton-conducting solid oxide fuel cell (H-SOFC). The utilization of X-ray diffraction method (XRD) and transmission electron microscopy (TEM) enables the identification of the presence of platinum (Pt) in both the crystal lattice sites and the grain interface. This occurrence contributes to a reduction in grain boundary resistance. Consequently, this phenomenon improves the conductivity of the electrolyte. The electrochemical performance of the single cell with Pt modified BZY electrolyte is improved by the reduction of ohmic resistance and enhancement of ion migration. This signifies a noteworthy advancement in the creation of more efficient and durable proton-conducting SOFCs.

Microbial Fuel Cells (MFCs) representing a promising technology for the extract of energy and resources through wastewater and it also offer an economic solution to the problem of environment effluent and energy crisis in near future. The advance device is rather appealing, due its potential benefits, its practical application is, however hindered by several drawbacks, such an internally competing microbial reaction, and low power generation. This report is an endeavor to address various design connected to the MFCs application to wastewater treatment, in particular cost effective bioelectricity from waste water are reviewed and discussed with a multidisciplinary approach. The conclusions drawn herein can be of practical interest to all new researchers dealing with effluent wastewater treatment using MFCs.

In a previous study we could show a change of membrane morphology and gas separation performance by varying the recipe of a casting solution based on polysulfone in a determined solvent system. Although all results were very reproducible, all used solvents were harmful and not sustainable. In this study therefore, the solvents tetrahydrofuran (THF) and N,N-dimethylacetamide (DMAc) are replaced by the more sustainable solvents 2-methyl-tetrahydrofuran (2M-THF), N-butyl pyrrolidinone (NBP) and cyclopentyl methyl ether (CPME). The gas permeation performance and for the first time morphology of the membranes before and after solvent replacement were determined and compared by single gas permeation measurements and SEM microscopy. It is shown, that THF can be replaced by 2M-THF and NBP without decreasing the gas permeation performance. With CPME replacing THF no membranes were formed. Best gas permeation results showed systems with 2M-THF as THF alternative. Permeances for the tested gases oxygen (O2), nitrogen (N2), carbon dioxide (CO2) and methane (CH4) were 2.66·10-4, 3.89·10-5, 1.53·10-3 and 4.52·10-5 mL(STP)/cm²·min·bar, respectively. permselectivities of those membranes for the gas pairs O2/N2, CO2/N2 and CO2/CH4 were 6.7, 38.3 and 34.0, respectively. When additionally replacing DMAc in the solvent system no or only porous membranes were obtained, even if the precipitation procedure was adjusted. These findings indicate that a complete replacement of the solvent system without affecting the membrane morphology or gas permeation performance is not possible. By varying the temperature of the precipitation bath an easy adjustment to mechanically stable PSU membranes is possible, if just THF was replaced by 2M-THF.

Normally, the Nernst voltage calculated from the concentration of the reaction gas in the flow channel is considered to be the ideal voltage (reversible voltage) of the oxyhydrogen fuel cell, but actually it will cause a concentration gradient when the reaction gas flows from the flow channel through the gas diffusion layer to the catalyst layer. The Nernst voltage loss in fuel cells in most of the current literature is thought to be due to the difference in concentration of reaction gas in the flow channel and concentration of reaction gas on the catalyst layer at the time when the high net current density is generated. Based on the Butler-Volmer equation in oxyhydrogen fuel cell, this paper demonstrates that the Nernst voltage loss is caused by the concentration difference of reaction gas in flow channel and on the catalytic layer at the time when equilibrium potential (Galvanic potential) of each electrode is generated.

CSZM compounds were synthesized by dry chemistry route with 5, 10, and 15% dopant of Mg dopants in the Ce 0.8-2x Sm 0.2 Zrx Mgx O2-d, {x = 0.05, 0.1 &0.15}. The newly investigated materials were physically, chemically, and electrochemically studied and have shown promising results. The CSZM was crystalized in a fluorite structure with a pure cubic phase in a space group Fm3m and cell parameter a = 5.401742 °A and theoretical density from 7.6 to 8.9 after firing in the air with a final temperature of 1400 °C. characterization of the structure and indexing of electrolyte materials were made after X-ray diffraction (XRD) testing. A Scanning electron microscope (SEM) morphological analysis was used to examine the microstructure details. Electronic impedance spectroscopy (EIS) measurements were achieved from 400 °C to 700 °C showing the highest value of conductivity of 1.0461 x 10+1 S/cm at 700 °C while the minimum value was 2.7329 x 10-2 S/cm at 400 °C and the total activation energy was found (Ea) 0.6865 eV under 5% H2/Ar.

A predictive approach to the phase behavior of four-component poly-mer-water-surfactant-electrolyte systems is formulated, by viewing the four-component system as a binary polymer-pseudosolvent system, with the pseudosolvent representing water, surfactant, and the electrolyte. The phase stability of this binary system is examined using the framework of the lattice fluid model of Sanchez and Lacombe. In the lattice fluid model, a pure component is represented by three equation of state parameters, the hard-core volume of a lattice site ( ), the number of lattice sites occupied by the component (r) and its characteristic energy ( ). We in-troduce the extra thermodynamic postulate that r and for the pseudosolvent are the same as for water and all surfactant-electrolyte composition dependent characteristics of the pseudosolvent can be represented solely through its characteristic energy parameter. The key implication of the postulate is that the phase behavior of polymer-pseudosolvent systems will be identical for all pseudosolvents with equal values of the characteristic energy, despite their varying real compo-sitions. Based on the pseudosolvent model, illustrative phase diagrams have been computed for several four-component systems containing alkyl sulfonate/sulfate surfactants, electrolytes and anionic or nonionic polymers. The pseudosolvent model is shown to describe all important trends in experimentally observed phase behavior, pertaining to polymer and surfactant molecular characteristics. Most importantly, the pseudosolvent model allows one to construct a priori phase diagrams for any polymer-surfactant-electrolyte system, knowing just one experimental com-position data for a system at the phase boundary, using available thermodynamic data on sur-factants and electrolytes and without requiring any information on the polymer.

In this study organic bulk heterojunction (BHJ) solar cell along with the spiro OMeTAD as a hole transport layer (HTL) and the PDINO as an electron transport layer (ETL) was simulated through the Solar Capacitance Simulator, one dimensional (SCAPS-1D) software to examine the performance of this type of polymer thin film organic solar cells. As an active layer the blend of polymer donor PBDB-T and non-fullerene acceptor ITIC-OE was used. Numerical simulation was performed by varying the thickness of HTL and active layer. Firstly, the HTL layer thickness was optimized to 50 nm, after that the active layer thickness varied up to 80 nm. These results of simulation demonstrated that the HTL thickness has rather little impact on efficiency while in the case of active layer thickness improves efficiency significantly. The temperature effect on the performance of solar cells was considered, by the simulation performed for temperature from 300 K up to 400 K and the efficiency of solar cell decreases with increasing temperature. Generally, polymer films usually are full of traps and defects, the density of defects (Nt) value was also introduced to the simulation, and it was confirmed that with the increasing of defect density (Nt), the efficiency of solar cell decreases. After thickness, temperature and defect density optimization, the reflection coating was also applied on it. It turned out that by introducing the reflection coating on the back side of solar cell, the efficiency increases by 2.5 %. Additionally, the positive effect of HTL and ETL doping on efficiency of this type of solar cells was demonstrated.

A hybrid material, consisting of commercially available nitrocellulose (NC) membrane non-covalently modified with amino-polyethylene glycol functionalized reduced graphene oxide (NH2-PEG-rGO) nanoparticles, was successfully synthesized for oligonucleotide extraction. Fourier Transform Infrared Spectroscopy (FTIR) confirmed the modification of the NC membrane, revealing characteristic peaks of both compounds NC and NH2-PEG-rGO. Scanning Electron Microscopy (SEM) exhibited morphological changes in the NC/NH2-PEG-rGO hybrid membrane, marked by the introduction of NH2-PEG-rGO particles, resulting in a distinctly smothered surface compared to the porous surface of the NC control membrane. Wettability assays revealed hydrophobic behavior for the NC/NH2-PEG-rGO hybrid membrane, with a water contact angle exceeding 90°, contrasting with the hydrophilic behavior characterized by a 16.7° contact angle in the NC membrane. The performance of the NC/NH2-PEG-rGO hybrid membrane was evaluated for the extraction of ssDNA with fewer than 50 nucleotides from solutions containing various ionic species (MnCl2, MgCl2, and MnCl2/MgCl2). The NC/NH2-PEG-rGO hybrid membrane exhibited optimal performance when incubated in MgCl2, presenting the highest fluorescence emission at 525 relative fluorescence units (r.f.u.). This corresponds to the extraction of approximately 610 pg (≈13%) of the total oligo-DNA, underscoring the efficacy of the pristine material, which extracts 286 pg (≈6%) of oligo-DNA in complex solutions.

The focus of this work lies in the construction of monitoring system designed in the form of a patch using a long-lasting potentiometric electrolyte concentration sensor from metal electrodes, in a galvanic cell configuration Mg(s)|NaCl(aq)|Cu(s). Initially, a mathematical analysis was conducted on the expected sensor output through the Nernst equation. The experimental phase involved conducting controlled tests in the laboratory using various molar concentrations of sodium chloride (NaCl) in aqueous solution. Results showed that the electrolyte sensor allows for monitoring electrolyte levels in NaCl in the range of 0.02 to 1 M/L, with electrode lifespan exceeding 10 days. On the other hand, when patch is using human sweat during controlled exercise routines, it showed the sensor's capability for monitoring changes in the subjects' hydration levels in real time. The sensor output potential is greater than 1.7 volts when the sensor electrodes are in contact with human sweat, which is equivalent to measuring molar concentrations at normal hydration and moderately high hydration levels. Sensor results indicate that the system can function in a self-powered manner without external batteries. Additionally, the extended lifespan of its electrodes allows for continuous monitoring of imbalances in the human body, showcasing the system capability for long-term health assessment.

Heat and power cogeneration plants based on fuel cells are interesting systems for energy- conversion at low environmental impact. Different fuel cells have been proposed, but experimental testing rigs are expensive and the development of commercial systems is time consuming if based on fully experimental activities. Furthermore, tight control of operation of fuel cells is compulsory to avoid damage, which must be based on accurate models, able to predict the cell behaviour and prevent stresses and shut-down. Some selected examples of steady state, dynamic and fluid dynamic modelling of different types of fuel cells are proposed, mainly PEMFC and SOFC type. The general ideas behind the thermodynamic, kinetic and transport description are recalled, with some examples of models derived for single cells, stacks and integrated power co-generation units.

The construction of optimized biological fuel cells requires a cathode which combines the longevity of a microbial catalyst with the power density of an enzymatic catalyst. Laccase secreting fungi were grown directly on the cathode of a biological fuel cell to facilitate the exchange of inactive enzymes with active enzymes with the goal of extending the lifetime of laccase cathodes. Additionally, a functionally graded coating was developed to increase enzyme loading at the cathode. Directly incorporating the laccase producing fungus at the cathode extends the operational lifetime of laccase cathodes while eliminating the need for frequent replenishment of the electrolyte. Additionally, the hybrid microbial-enzymatic cathode addresses the issue of enzyme inactivation by using the natural ability of fungi to exchange inactive laccases at the cathode with active laccases. Finally, enzyme adsorption was increased through the use of a functionally graded coating containing an optimized ratio of titanium dioxide nanoparticles and single walled carbon nanotubes. The hybrid microbial-enzymatic fuel cell combines the higher power density of enzymatic fuel cells with the longevity of microbial fuel cells and demonstrates the feasibility of a self-regenerating fuel cell in which inactive laccases are continuously exchanged with active laccases.

This study aimed to enhance the compatibility of glass ionomer cement (GIC) with tooth tissue by chemically modifying its primary component, calciumfluoroaluminosilicate (CFAS), through the incorporation of nanorod hydroxyapatite (nHA). The process involved binding L-glutamic acid to nHA, followed by activation and binding of albumin to create nHA immobilized with albumin. This modified nHA was then used to surface-modify CFAS particles, producing nHA-CFAS powder. The modified powder was mixed with poly(acrylic acid) and UV-cured to form GIC containing nHA-CFAS (GIC-nHA). Fourier transform infrared spectroscopy and scanning electron microscopy (SEM) confirmed the successful modification. Cytocompatibility tests with osteoblasts showed that GIC-nHA had superior cell viability and bone formation capabilities compared to the control GIC. The improved histocompatibility is attributed to nHA enhancing the biological activity of osteoblasts, indicating that the surface modification method significantly improves the functional integration of GIC with tooth tissue.

The objective of this research project was to evaluate the effects of the addition of inorganic fillers into PEBA at various loading levels on the processing, mechanical, thermal and physical properties of the polymer. The composites investigated in this study were Pebax® 6333 SA01 MED (PEBA100) with 10 wt.%, 20 wt.% and 30 wt.% Barium Sulphate (PEBA/BaSO4) and Bismuth Oxychloride (PEBA/BiOCl) respectively. Composites were prepared using twin screw extrusion and injection moulding. Post-processing, composite samples were analysed for their mechanical properties (via tensile, impact and flexural analysis), thermal properties (via differential scanning calorimetry), rheological performance (via melt flow index) and physical properties (via density analysis and ash content testing). The results of which reveal how filler type and concentration influence PEBA composites. The results of the study suggest that BiOCl filler enhances the aesthetic properties, increases the stiffness, while maintaining some level of flexibility with minimal adverse effects on the tensile and impact strength. When comparing BiOCl to BaSO4 filled composites, it was clear that depending on the application of the polymer composite, BiOCl may provide more desirable properties. The study highlights the importance of optimising filler concentration and processing conditions to achieve desired composite properties for specific medical applications.

: Microbial fuel cell (MFCs) devices utilise the metabolic processes of bacteria to generate electricity from various organic substrates. Due to the enormous amount of energy that organic waste produces, scientists are highly interested in advanced MFCs. MFCs serve as a multidisciplinary research platform at the engineering and natural sciences intersection. MFCs have various uses besides being used as energy sources, such as sensing capabilities. Despite showing considerable promise, only a few marine sediment MFCs have been deployed in real-world applications to supply current for low-power devices. It is now required to maintain track of the work being done by research groups worldwide and regularly compile significant discoveries due to the rising quantity of research publications. Review papers are a traditional beginning point for a literature review for new scholars. This review is a fast reckoner that directs readers to pertinent reviews and research publications detailing significant advances in microbial fuel cell research during the previous two decades. An overview of key advances in MFC research over the past two decades is provided as a quick reference in this review article. In addition, the report identifies research gaps that, if filled, could bring this technology closer to real-world use.

Microgrids offer flexibility in power generation in a way of using multiple renewable energy sources. In the past few years, microgrids become a very active research area in terms of design and control strategies. Most of the microgrids use DC/DC converters to connect renewable energy sources to the load. In this paper, the simulation model of a DC microgrid with three different energy sources (Lithium-ion battery (LIB), photovoltaic (PV) array, and fuel cell) and external variant power load is built with MATLAB/Simulink and the simulative results show that the stability of DC microgrid can be guaranteed by the proposed maximum power point controller MPPT. The three energy sources are connected to the load through DC/DC converters, one for each. This type of topology ensures protection for each energy source as well as optimum stability at the load.

In this work, dry and hydrothermal carbonization (DC and HTC) of RDF pellets were conducted to evaluate the physical, chemical, and fuel properties of the produced chars. In the dry carbonization tests, biomass sawdust was incorporated in different proportions on the samples to minimize agglomeration caused by the melting of the plastic fraction. The experiments were carried out in a temperature of 400°C (DC) and 250-300°C (HTC), in a residence time of 30 minutes. The respective chars and hydrochars were characterized according to their mass yield, apparent density, proximate, elemental, and mineral composition, chlorine content, high heating value, thermogravimetric profile, and surface functional groups. The results showed that dry carbonization of RDF pellets with biomass incorporation, followed by a washing step, resulted in the production of chars with improved properties such as higher fixed carbon and HHV (25-26 MJ/kg) and lower ash and chlorine content. Additionally, the HTC experiments demonstrated that hydrochars showed improved properties without the need for biomass addition and washing, however, with no significant difference in the HHV (20-21 MJ/kg). Therefore, DC of RDF pellets with 10% biomass incorporation seems to be a promising option to overcome the constraints of RDF utilization as an alternative fuel.

A binary biomass-based solid electrolyte film (LSE) was successfully synthesized through the incorporation of lignin nanoparticles (LNP) with sodium alginate (SA). The impact of the mass ratio of SA to LNP on the microstructure, porosity, electrolyte absorption capacity, ionic conductivity, and electrochemical properties of the LSE was thoroughly investigated. The results indicated that as the proportion of SA increased from 5% to 15% LNP, the pore structure of the LSE became increasingly uniform and abundant. Consequently, enhancements were observed in porosity, liquid absorption capacity, ionic conductivity, and overall electrochemical performance. Notably, at a SA amount of 15% LNP, the ionic conductivity of resultant LSE-15 was recorded at 14.10 mS cm1, with porosity and liquid absorption rates reaching 308% and 58.4%, respectively. LSE-15 was employed as a solid electrolyte, while LNP-based carbon aerogel (LCA) served as the two electrodes in the construction of a symmetric all-solid-state supercapacitor (SSC). The SSC device demonstrated exceptional electrochemical storage capacity, achieving a specific capacitance of 197 F g1 at 0.5 A g1, along with maximum energy and power density of 27.33 W h kg1 and 4998 W kg1, respectively. Furthermore, the SSC device exhibited highly stable electrochemical performance under extreme conditions, including compression, bending, and both series and parallel connections. Therefore, the development and application of the binary biomass-based solid electrolyte film in supercapacitors represent a promising strategy for harnessing high-value biomass resources in the field of energy storage.

Cancer remains a leading cause of death despite advancements in research and treatment, with traditional therapies often causing significant side effects and resistance. Oxyhydrogen gas, a mixture of 66% molecular hydrogen (H₂) and 33% molecular oxygen (O₂) has shown exceptional promise as a novel therapeutic agent due to its ability to modulate oxidative stress, inflammation, and apoptosis. H2, a key component of oxy-hydrogen gas, neutralises reactive oxygen and nitrogen species, enhancing existing treatments and reducing harmful oxidative states in cancer cells. H₂ also lowers pro-inflammatory mediators including chemokines, cytokines and interleukins, inhibiting cancer cell proliferation and boosting the effectiveness of conventional therapies. Additionally, hydrogen can induce apoptosis in cancer cells by modulating pathways such as MAPK and inhibiting the PI3K/Akt phosphorylation cascade. Preclinical and clinical evidence supports oxyhydrogen gas's potential in treating various cancers. In lung cancer models, it inhibits cell proliferation, induces apoptosis, and enhances chemotherapy sensitivity. Similar results have been observed in breast cancer, where patients reported improved quality of life. In colorectal cancer, oxyhydrogen gas suppresses tumour growth, induces apoptosis and improves intestinal microflora dysbiosis. The unique properties of oxyhydrogen gas make it a promising adjunctive or standalone cancer treatment. However, further research is needed to understand H₂'s mechanisms, optimise treatment protocols, and evaluate long-term safety and efficacy in human patients.

The goal of this work was to develop the acrylonitrile-butadiene (NBR) elastomer composites filled with hydroxyapatite (HAP), which were characterized with improved cure characteristics and burning resistance. Silane, i.e., (3-aminopropyl)-triethoxysilane, ionic liquid, i.e., 1-decyl-3-methylimidazolium bromide and surfactant, i.e., cetyltrimethylammonium bromide, were used to improve the filler’s dispersibility in the elastomer matrix and to reduce the time and temperature of vulcanization. The effect of HAP and dispersants on the cure characteristics, crosslink density and physico-chemical properties of NBR composites was explored. The additives used, especially the ionic liquid and surfactant, effectively improved the dispersion of HAP in NBR matrix. The amount of HAP and the dispersant used strongly affected the cure characteristics and crosslink density of NBR. The optimal vulcanization time significantly increased with HAP content and was pronouncedly reduced when ionic liquid and surfactant were applied. In addition, ionic liquid and surfactant significantly lowered the onset vulcanization temperature, improved the crosslink density and hardness of the vulcanizates, while impairing their elasticity. HAP and dispersants did not significantly affect the damping properties and chemical resistance of NBR vulcanizates. Above all, application of HAP considerably enhanced the resistance of vulcanizates to thermo-oxidative aging and reduced their flammability compared to the unfilled NBR.

Some global difficulties in the modern period include energy storage conversion. Researchers have looked to renewable energy resources to discover long-term answers to this dilemma. Fuel cells are one example of prospective energy producing technology. Although these technologies appear to be very enticing, they are known to be expensive due to high expenses. Catalyst costs, as well as concerns concerning energy density. Pt based Electrocatalysts have traditionally been used to drive ORR and offer efficient power outputs. However, cost constraints have limited the use of these electrocatalysts, rendering them inefficient. Apart from the high price, Pt-based Electrodes are prone to time-dependent drift and CO deactivation, both of which occur gradually. Electrocatalysts deteriorate over time, reducing the efficiency of fuel cells. This is why alternative electrocatalysts are in high demand for future energy applications. This review covers the comparative study of Platinium and Non-Platinium based electrocatalyst in fuel cells, their shortcomings and recent advancement for efficient and optimized electrocatalyst.

This article presents new PEM fuel cell models with hexagonal and pentagonal designs. After observing cell performance improvement in these models, we optimized them. Inlet pressure and temperature were used as input parameters, and consumption and output power were the target parameters of the multi-objective optimization algorithm. Then we used artificial intelligence techniques, including deep neural networks and polynomial regression, to model the data. Next, we employed the RSM (Response Surface Method) method to derive the target functions. Furthermore, we applied the NSGA-II multi-objective genetic algorithm to optimize the targets. Compared to the base model (Cubic), the optimized Pentagonal and Hexagonal models averagely increase the output current density by 21.819\% and 39.931\%, respectively.

We observed and studied the phenomenon of the redox front propagation in different polyaniline (PAni) deposited samples interfaced with liquid or solid polymeric electrolyte. The front of electrochemical conversion, in which the insulator and the conductor parts of PAni are interfaced, is studied observing the temporal evolution of the conductivity of PAni samples. The propagation of redox front was studied in electrochemically obtained thick (2 µm) and in thin (50 nm) poly-aniline films, obtained using Langmuir-Blodgett (LB) method. In the configuration that we tested, the speed of the red-ox front propagation for the thin LB films was found to be 200 micron/sec opening the way for the manufacturing large neural networks, realized using PAni based memristive devices, in which the memristance can be quickly changed in the programmable manner. The prototypes of the spiking neuron connections were manufactured on the basis of lithographically developed gold contacts, bridged by electrochemically grown polyaniline and placed under polymer electrolyte layer with only one counter electrode (gate) for the whole manifold of pseudo-two-terminal memristor bridges. The spike propagation was studied in such gold-polyaniline systems. The research opens the possibility of miniature spike or rate-based neural network circuits manufacture, based on metal pads and polyaniline.

Maritime data not only identify financial resources that can significantly enhance the efficiency of shipping companies but also play a pivotal role in promoting eco-friendly and sustainable shipping practices. However, active corporate strategies are required to include maritime data essential for the commercial operation of autonomous ships in the form of corporate assets by transparent evaluating the data. The aim of this study is to review previous studies on da-ta-valuation models, identify a valuation model suitable for maritime business, consider the characteristics of maritime data. The analytic hierarchy process (AHP) method is used to derive priorities for valuing maritime data assets, with emphasis placed on the characteristics of mari-time data, followed by the character of the future-oriented maritime-data market and the da-ta-valuation model. The results obtained that the most important factors in selecting a maritime data-valuation model by analyzing the AHP method were identified as the characteristics of the maritime data(M1). The next most important factors analyzed were the features of the mari-time-data market(M2) and the features of the maritime data-valuation model(M3) in order. In addition, the characteristics of maritime data were preferentially considered among the main criteria, and the market approach (A2) was selected as the most optimal valuation model. The potential impact of this implementation could contribute to the establishment of an intelligent technology market by estimating the value of data and developing a platform for maritime data trading, allowing for more efficient data sharing and utilization by maritime autonomous sur-face ship(MASS).

Exsolved perovskites can be obtained from lanthanum ferrites, such as La0.6Sr0.4Fe0.8Co0.2O3, as result of Ni doping and thermal treatments. Ni can be simply added to the perovskite by an incipient wetness method. Thermal treatments include calcination in air (e.g., 500 °C) and subsequent reduction in diluted H2 at 800 °C to favor the exsolution process. The chemistry of the nanoparticles exsoluted on the substrate surface can be further modulated by a post treatment in air. These processes allow to produce a two-phase material consisting of a Ruddlesden-Popper type structure and a solid oxide solution e.g. α-Fe100-y-zCoyNizOx oxide. The formed electro-catalyst shows sufficient electronic conductivity under reducing environment at the SOFC anode. Outstanding catalytic properties are observed for the direct oxidation of dry fuels in SOFCs, including H2, methane, syngas, methanol, glycerol and propane. This anode electrocatalyst can be combined with full density electrolyte based on Gadolinia-doped Ceria or with La0.8Sr0.2Ga0.8Mg0.2O3 (LSGM) or BaCe0.9Y0.1O3-δ (BYCO) to form a complete perovskite structure-based cell. Moreover, the exsolved perovskite can be used as a coating layer or catalytic pre-layer of a conventional Ni-YSZ anode. Beside the excellent catalytic activity, this material also shows proper durability and tolerance to sulphur poisoning. In this mini review, preparation methods, physico-chemical characteristics, surface properties of exsoluted and core-shell nanoparticles encapsulated on the metal-depleted perovskite substrate surface, electrochemical properties for the direct oxidation of dry fuels and related electrooxidation mechanisms are examined and discussed.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

The anode of a microbial fuel cell (MFC) was formed on a graphite electrode and immobilized Gluconobacter oxydans VKM-1280 bacterial cells. Immobilization was performed in chitosan, poly(vinyl alcohol) or N-vinylpyrrolidone-modified poly(vinyl alcohol). Ethanol was used as substrate. The anode was modified using multiwalled carbon nanotubes. The aim of the modification was to create a conductive network between cell lipid membranes, containing exposed PQQ-dependent alcoholdehydrogenases, and the electrode to facilitate electron transfer in the system. The bioelectrochemical characteristics of modified anodes at various cell/polymer ratios were assessed via current density, power density, polarization curves and impedance spectres. MFCs based on chitosan at a matrix/cell volume ratio of 5:1 produced maximal power characteristics of the system (8.3 μW/cm2) at a minimal resistance (1111 Ohm cm2). Modification of the anode by multiwalled carbon nanotubes led to a slight decrease of internal resistance (down to 1078 Ohm cm2) and to an increase of generated power density up to 10.6 μW/cm2. We explored the possibility of accumulating electric energy from an MFC on a 6,800-μF capacitor via a boost converter. Generated voltage was increased from 0.3 V up to 3.2 V. Accumulated energy was used to power a Clark-type biosensor and a bluetooth transmitter with three sensors, a miniature electric motor and a light-emitting diode.

Plants Microbial Fuel Cells (PMFC) is a new technology that generates electricity in a renewable, clean and sustainable way. In spite of these advantages, it still faces limitations in power generation and current density, reaching lower production values than other renewable technologies. Different studies maintain that the high resistivity of the cathode is the main limitation in the generation of energy; therefore, non-metallic materials to obtain a better performance are replacing the metallic electrodes. The implementation of these materials applied to PMFC requires a complex interdisciplinary work. Through three experimental tests using metallic electrodes for the extraction of electrons, this research study shows that the treatment of the substrate with natural materials, the volume plant roots, and substrate temperature and humidity control have a significant influence in the increase of the electric potential and the generated current.

We introduce a series of twisted donor-acceptor (D-A) carbazole-benzophenone based electroactive bipolar derivatives that were synthesized through the reaction of 4-fluorobenzophenone with various partially alkylated 3,3’-bicarbazoles. The comprehensive structural characterization of these compounds is provided. These amorphous materials exhibit suitable glass transition temperatures ranging from 57 to 102 °C and demonstrate high thermal stability, with decomposition temperatures reaching 400 °C. Moreover, the developed materials exhibit elevated photoluminescence quantum yields (PLQY) of up to 75.5% and favorable HOMO-LUMO levels, along with suitable triplet-singlet state energy values. Due to their good solubility and suitable film-forming properties, all the compounds were evaluated as blue emitters dispersed in 4,4’-bis(N-carbazolyl)-1,10-biphenyl (CBP) host for the fabrication of organic light-emitting diodes (OLEDs) in concentration dependent experiments. Among these experiments, the device containing 15 wt% of the guest 4-(9’-{2-ethylhexyl}-[3,3’]-bicarbazol-9-yl)benzophenone demonstrated the best characteristics, achieving maximum brightness of 3581 cd/m2, current efficiency of 5.7 cd/A, power efficiency of 4.1 lm/W and external quantum efficiency of 2.7%.

The paper presents a method to assess the effect of electrolyte additives on the energy capacity of Pb-acid batteries. The method applies to any chemically unreactive additive, including suspensions and gels. The approach is thermodynamically based and it leads to the definition of a region of admissible concentrations –the battery’s admissible range– where the battery can undergo an indefinite number of charge/discharge cycles without suffering permanent damage. An experimental procedure to determine this range is presented. The obtained results provide a way to assess the potential of electrolyte additives to improve the energy capacity of Pb-acid batteries. The same results also provide a means to determine the additive concentration that produces the maximum energy capacity increase of the battery. The paper closes with an example of application of the proposed approach to a practical case.

Environmental pollution is becoming ubiquitous; it has a negative impact on the ecosystem diversity and worsens the quality of human life. This review discusses the possibility of applying the Plant Microbial Fuel Cells (PMFC) technology for concurrent processes of electricity generation, purification of water and soil ecosystems from organic pollutants, in particular, from synthetic surfactants and heavy metals. The review describes the PMFC functioning mechanisms and highlights the issues of the PMFC environmental application. Generally, this work summarizes different approaches to the PMFC development and to the potential usage of such hybrid bioelectrochemical systems for the environmental protection.

We have successfully developed curcumin nanosuspension aimed for oral delivery. The main purpose is to improve bioavailability through enhancing its solubility. The nanoparticles were stabilized using various stabilizers including polyvinyl pyrrolidone (PVP), polyvinyl alcohol (PVA), sodium carboxymethylcellulose (Na-CMC), d-alpha tocopheryl polyethylene glycol 1000 succinate (TPGS), and sodium dodecyl sulfate (SDS). The average diameter of particles, microscopic appearance, and sedimentation of each preparation was observed and compared. Each stabilizer demonstrated different degree of inhibition of particle aggregation under electrolyte-containing simulated gastrointestinal (GIT) fluid. Non-ionic stabilizers (PVA, PVP, and TPGS) has shown to preserve the nanosuspension stability against electrolytes. In contrast, strong ionic surfactants such as SDS were found to be very sensitive to electrolytes. The results can provide useful information for the formulators to choose the most suitable stabilizers by considering the nature of stabilizers and physiological characteristics of target site of the drug.

The present investigation highlights the synthesis of polyaniline (PANI) coated graphene oxide doped with SrTiO3 nanocube nanocomposites through facile in-situ oxidative polymerization method for the efficient removal of carcinogenic dyes, namely, the cationic dye methylene blue (MB) and the anionic dye methyl orange (MO). The synthesised nanocomposites were characterised by field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). The adsorption efficiencies of graphene oxide (GO), PANI homopolymer and SrTiO3 nanocubes-doped nanocomposites were assessed by monitoring the adsorption of methylene blue and methyl orange dyes from aqueous solution. The adsorption efficiency of nanocomposites doped with SrTiO3 nanocubes were found to be of higher magnitude as compared with undoped nanocomposite. Moreover, the nanocomposite with 2 wt% SrTiO3 with respect to graphene oxide demonstrated excellent adsorption behaviour with 99% and 91% removal of MB and MO respectively, in a very short duration of time.

In this study, the determination of static E50 and υ parameters of rock materials was investigated using P-S wave velocities and Shore hardness (SH), non-destructive measurement methods. We used multiple linear regression (MLR), multiple non-linear regression (MNLR) and artificial neural network (ANN) models to estimate and determine these parameters. When the models defined by MLR, MNLR, and ANN were compared to the R2 values, ANN models that estimate E50 and υ parameters of rock materials using non-destructive methods (Vp, Vs, Vp/Vs, d, and SH) could be determined with higher accuracy than MLR and MNLR models. The study’s originality is based on the fact that ores such as galena, chromite, and barite have been studied for the first time on rock mechanics, and in this respect, it offers an innovative perspective. In addition, the use of all non-destructive measurement methods, Vp, Vs, and Shore hardness tests, also increases the originality of the study.

Displacement mapping is a computer graphics technique that enables the design of components with regularly or randomly textured surfaces that can be quickly materialized on a three-dimensional (3D) printer when needed. This approach is in principle more flexible, faster and more economical compared to conventional texturing methods, but the accuracy of the texture depends heavily on the parameters used. The purpose of this study is to demonstrate how to produce a surface-textured part using polygonal (mesh) modeling software and a photopolymerizable resin, and to develop a universal methodology to predict the dimensional accuracy of the model file log combined with a resin 3D printer. The printed components were characterized on a scanning confocal microscope. In the setup used in this study, the mesh size had to be reduced to 10% of the smallest feature size and the textured layer had to be heavily (x4) overexposed to achieve the desired accuracy. As a practical application, two functional stamps with a regular (honeycomb) and a random texture, respectively, were successfully manufactured. The insights gained will be of great benefit in quickly and cost-effectively producing components with innovative patterns and textures for a variety of hobby, industrial and biomedical applications.

This work demonstrates that microbial fuel cells (MFCs), optimized for energy recovery, can be used as an effective tool to detect the presence of antibiotics in water-based environments. MFCs directly convert chemical energy of organic matter in electrical energy thanks to electroactive biofilms. The efficiency of the conversion process can be significantly affected by the presence of contaminants acting as toxicants for the biofilm. In the present work, we demonstrate that MFCs can successfully detect the presence of antibiotic residues in water and water-based electrolytes associated to the food industry, especially using honey as a new and more complex electron donor. The effectiveness of MFCs to sense antibiotics is here demonstrated for tetracycline that was added to both water and water/honey electrolytes with a minimum concentration close to 3.5 μg⁄kg. MFCs not only efficiently detect the presence of tetracycline in both the electrolytes, but also recover the same performance after each cycle of exposure, showing to a be very robust and reliable technology for both biosensing and energy recovery.

Electrolyte disturbances are common in patients with traumatic brain injury (TBI), particularly affecting sodium, potassium, chloride and calcium levels. This study aims to provide insights into these disturbances within the first 24 hours post-injury. We conducted a cross-sectional analysis of 50 TBI patients, excluding those with conditions affecting electrolyte balance. Electrolyte levels were measured, and correlations with demographic data, trauma mechanisms, imaging findings, and Glasgow Coma Scale (GCS) scores were analyzed. Results indicated that chloride levels inversely correlated with GCS scores (ρ = -0.515; p = 0.002), suggesting that elevated chloride may indicate severe neurological impairment. Potassium levels were significantly associated with subdural hematoma (p = 0.032) and subarachnoid hemorrhage (p = 0.043), highlighting their potential as markers for severe brain injuries. No significant associations were found between sodium or calcium levels and the studied variables. These findings underscore the importance of early monitoring of chloride and potassium levels in TBI patients to improve management and outcomes. Future research should focus on larger, multi-center studies to validate these findings and develop comprehensive guidelines for managing electrolyte imbalances in TBI patients.

This study proposes a redesign of asymmetric single-chamber microbial fuel cells (a-SCMFC) with the goal of optimizing energy production. The new approach is based on the introduction of an Intermediate Microfluidic Septum (IMS) as a relatively simple and inexpensive method to opti-mize both electrolyte flow and species transfer inside the devices. SCMFCs with the novel IMS, operated with sodium acetate as the carbon source, demonstrate to enhance the energy recovery (Erec) factor, defined as the ratio between the energy yield and the inner volume of electrolyte. In standard operative conditions, cells with IMS exhibit Erec value of (37±1) J/m3, with respect to (3.0±0.3) J/m3 of control cells. Furthermore, changing sodium acetate concentration the Erec values change accordingly. By monitoring the activity of a-SCMFCs for over one-year, beneficial impact of the IMS on both the initial inoculation phase and the long-term stability of electrical perfor-mance were observed. These improvements suggest the effectiveness of IMS to allow the de-velopment of efficient biofilms, likely due to the reduction in oxygen diffusion towards the anode. Electrochemical characterizations confirm that the presence of the IMS impacts the diffusion processes inside the electrolytic chamber, supporting the hypothesis of a beneficial effect on oxygen diffusion.

This study develops into the application of a combined MFC unit with chemical coagulation for total treatment of inert contaminants in complex substrates. Microbial Fuel Cell (MFC) technology converts chemical energy in the form of organic matter, into bioelectricity in an environmentally friendly and effi-cient manner, reducing carbon emissions and increasing bioenergy production. An evaluation of a la-boratory scale chemical coagulation using an aluminum and poly-based coagulant on how effective it can remove bulk impurities such as particulate COD and turbidity to obtain the purest and most cost-effectively treated wastewater using a jar test is being conducted in this current study. This study aims to find the most effective treatment technologies for wastewater recovery in breweries in order to achieve zero liquid effluent discharge (ZLED). The preliminary results showed that adding a modest amount of poly and a 50 % alum alone treatment improved COD, color, and turbidity reduction. The turbidity removal efficiency achieved after chemical coagulation treatment was 90.50 % and 59.36 % COD removal, demonstrating the benefits of adopting an alum/poly based technique. To determine ZLED, this study clearly advised a combined treatment technique, specifically the MFC-flocculator unit for efficient organics and inorganics removal.

Metal-supported fuel cells (MSCs) offer potential material cost and robustness advantage over anode supported cells (ASCs). Because of the very good thermal shock stability of such MSCs, these can be heated up very quickly. However the challenge co-firing of metal substrate and electrolyte stays still unsolved. The production of the core component, the tape casted metal substrate, with defined shrinkage resulting from modification of metal powders is presented in the paper. This approach leads to an adjustment of the shrinkage mismatch during sintering, between metal and ceramic components, and adjustment of target specifications like porosity, green density and layer thickness.

A better understanding of high temperature processes in slags contributes to facilitate knowledge based design of the solidified product. Here, a slag analogue with a nominal composition of 17 wt% LiMnO2 and 83 wt% Ca2SiO4 was synthesized encountering fairly high cooling rates. The Mn species from 1223 K to 1773 K was simulated using a thermodynamic model assuming a homogeneous melt. The micro-composition including the Mn species of the solidified slag was determined experimentally and was used as basis for molecular dynamics (MD) simulation. The MD simulation provides information on structure and viscosity at high temperatures, otherwise difficult to access. These parameters significantly influence oxidation state of redox-active elements and the solidified product. The micro-composition analyzed by electron probe micro analysis (EPMA) and synchrotron based micro-X-ray fluorescence (micro-XRF) showed that Mn-rich and Ca-Si-rich phases are separated. While the Mn-O phases did not contain noticeable Ca, the Ca2SiO4 phase had incorporated 0.6 wt% of Mn. The slag solidified into round shaped and droplet shaped grains of a Li-Mn-oxide, some Mn3O4 and Ca2SiO4. The powder X-ray diffraction (PXRD) confirmed the formation of larnite, the identity of the Li-Mn-oxide however remained inconclusive. The Mn oxidation state (OS) was identified using synchrotron based micro-X-ray absorption near edge spectroscopy (micro-XANES). The Mn-O grains, matched well with Li-Mn-oxides and a Mn OS: +3 e.g. LiMn3+O2. Small areas matching Hausmannite (Mn2+Mn23+O4) were also identified. The OS of Mn in the silicate phase could not be identified. For comparison a slowly cooled slag analogue with similar composition however higher Si content, was also subjected to micro-XANES. The slowly cooled slag formed long Mn-rich needles in a matrix of large calcium silicate crystals. The Mn-rich crystals matched well with the XANES spectrum of a Mn3+ Li-oxide like LiMn3+O2. At the rim of the needles the Mn-spectra matched well the Hausmannite (Mn2+Mn23+O4) reference. In the silicate phases Mn had a OS: +2, unambiguously. The melt structure at different temperatures of two compositions i.e. LiMn3+O2 and Ca2SiO4 was simulated using molecular dynamics (MD). They serve as model compositions assuming a heterogeneous melt. The results show significant different degrees of polymerization and viscosity. Information from MD simulations can support the identification of potentially different oxygen permeability and with that prediction of oxidation states. The bulk composition was identified by inductively coupled plasma optical emission spectrometry (ICP-OES), bulk structure by PXRD and bulk species by lab-XANES. The synchrotron micro analysis including micro-XRD were performed at the microfocus beamline I18 at the Diamond Light Source. Pure reference compounds were prepared and characterized with the same multi-modal approach.

The model proposed in this study was based on the assumption that the biomass attached to the anode served as biocatalysts for MFC exoelectrogenesis, and this catalytic effect was quantified by the exchange current density of anode. By modifying the Freter model and combining it with the Butler-Volmer equation, this model could adequately describe the processes of electricity generation, substrate utilization, and the suspended and attached biomass concentrations, at both batch and continuous operating modes. MFC performance is affected by the operating variables such as initial substrate concentration, external resistor, influent substrate concentration, and dilution rate, and these variables were revealed to have complex interactions by data simulation. The external power generation and energy efficiency were considered as indices for MFC performance. The simulated results explained that an intermediate initial substrate concentration (about 100 mg/L under this reactor configuration) needed to be chosen to achieve maximum overall energy efficiency from substrate in the batch mode. An external resistor with the value about that of the internal resistance boosted the power generation, and a resistor with several times of that of the internal resistance achieved better overall energy efficiency. At continuous mode, dilution rate significantly impacted the steady-state substrate concentration level (thus substrate removal efficiency and rate), and attached biomass could be fully developed when the influent substrate concentration was equal to or higher than 100 mg/L at any dilution rate of the tested range. Overall, this relatively simple model provided a convenient way for evaluating and optimizing the performance of MFC reactors by regulating operating parameters.

The high dependence on light crude oil as the main source of energy in automobiles., industrial processes, source of raw material for various industrial synthesis have made the heavy crude more available in the world and open for research work on its potentials as a source of energy for the increasing population of the world in areas like energy source for powering big marine engines, energy source in heavy industrial machines e.t.c. Though the relatively unfavourable characteristics of heavy fuel oil such as; high viscosity, high probability of precipitating is a reasonable challenge to the possible utilization of heavy fuel as a source of energy in the areas highlighted above. These issues of heavy fuel oil are largely due to the presence of Asphaltene in it which is a large complex hydrocarbon in heavy fuel oil. Understanding the combustion potential of asphaltene is therefore an interesting and challenging problem that has attracted increasing attention from both academia and industry. This research work is aimed at carrying combustion studies on the Forcados (Ni-geria) heavy fuel fraction asphaltene HFFA extracted from Forcados crude Oil and examining its combustion characteristics with the view to examine it for future sweet heavy fuel generation for it source got low sulphur content, to ascertain the volatile composition, moisture and ash content. The HFFA extracted to determine physical characteristics of the HFFA extracted for fuel properties potentialities and this study was carried out to evaluate the chemical constituents of forcadous asphaltene lead-ing to the generaration of HFFA using GCMS. The Forcados asphaltene showed some good fuel properties when subjected to ce-tane number, API gravity, flash point and cloud point parameter test. Probing further with AAS for trace metal presence showed some high concentration on Chromium (Cr), Nickel (Ni), Iron (Fe), Lead (Pb), Cadmium (Cd), Copper (Cu), Manganese (Mn) and Zinc (Zn) indicating the potential for residual and soot formation after combus-tion. But still being a sweet asphaltene from Nigerian sweet crude source will be de-void of corrosive effect on machineries and heavy fuel engine if used to power it as in the case of high sulphur content in Venezuelan crude oil and some other world. The GCMS showed the decomposition of heavy crude asphaltene peaks and sig-naling the presence of heavy fuel fraction in the composition of the asphaltene while the FTIR and the UV-VIS identified the various functional groups in the compounds and the identification of signals that cannot be seen in the normal spectrum respec-tively.

This work investigates a new nanostructured gas-diffusion-layer (nano-GDL) to improve performance of air-cathode Single-Chamber-Microbial-Fuel-Cells (a-SCMFCs). The new nano-GDLs improves the direct oxygen-reduction-reaction by exploiting the best of nanofibers from electrospinning in terms of high surface ratio to volume and high porosity, and laser-based processing to promote adhesion. Nano-GDLs by electrospinning were fabricated directly collecting two nanofibers mats on the same carbon-based electrode, acting as the substrate. Each layer was designed with a specific function: water resistant, oxygen permeable polyvinylidene-difluoride (PVDF) nanofibers served as a barrier to prevent water-based electrolyte leakage, while an inner layer of cellulose nanofibers was added to promote oxygen diffusion towards the catalytic sites. The maximum current density obtained for a-SCMFCs with the new nano-GDLs is (132.2 ± 10.8) mA m^-2, and it doubles the current density obtained with standard PTFE-based GDL (58.5 ± 2.4 mA m^-2), used as reference material. The energy recovery (EF) factor, i.e. the ratio of the power output to the inner volume of the device, was then used to evaluate the overall performance of a-SCMFCs. a-SCMFCs with nano-GDL provided an EF value of 60.83 mJ m^-3: one order of magnitude higher than the value of 3.92 mJ m^-3 obtained with standard GDL

The proton conductivity, phase composition and mechanical properties of (1-x)CsH2PO4–x fluoropolymer electrolytes (x-mass fraction, x=0-0.3) have been investigated firstly and discussed. UPTFE and PVDF-based polymers (F2M, F42, SKF26) with the high mechanical properties and thermal stability have been chosen as a fluoropolymer additive. According the XRD data, a monoclinic CsH2PO4 (P21/m) phase is retained in all compositions of the polymer electrolytes studied. The conductivity of (1-x)CsH2PO4-x fluoropolymer in the high-temperature phase decreases by approximately one order of magnitude compared with the pure CsH2PO4 for x~0.15-0.20. The size and shape of CsH2PO4 particles and their distribution have been shown to affect significantly the proton conductivity and mechanical properties of the membranes. The thin-film composite systems were produced by various methods of the obtaining salt particles, their mixing and applying to a polymer matrix. The uniform distribution of particles in the polymer systems with the size of ~300 nm was achieved by a pretreatment of the suspension in a bead mill. CsH2PO4-based mechanically strong membranes with the thickness ~50–100 μm were obtained for the soluble fluoropolymers (F2M, F42, SKF26). With an increase in the mass fraction of the polymer the ability of the membranes to resist the plastic deformation and the mechanical strength increases and comparable to the best low temperature membranes. The proton-conducting membranes (1-x)CsH2PO4 – x fluoropolymer with the optimal combination of the conductivity, mechanical and hydrophobic properties are promising for use in solid acid fuel cells.

The power conversion efficiency (PCE) of polymer solar cells (PSCs) are strongly depended on the bulk-heterojunction active layer. Here, the 1,8-diiodooctane (DIO) additives have been added into the PCDTBT: PC70BM blend PSCs. Based on the higher boiling point than host solvent ODB and better solubility of PC71BM, the device photovoltaic properties with DIO additive were changed obviously. The investigations of EQE indicate that the DIO can influence the charge recombination and transportation process, and absorption studies demonstrate that the charge carriers generation process can also be affected by DIO. The overall impact reflected on the decreased equivalent resistant. With 3% v/v DIO, the Jsc, Voc and FF are both increased. Correspondingly, a highest PCE is achieved of 6.15%, while the reference device without DIO only has a PCE of 5.23%. Hence, adding DIO solvent additive is a effective method for the photovoltaic properties improving of PCDTBT: PC70BM blend PSCs.

The two-phase flow of water and reactive gas in the channel of proton exchange membrane fuel cell (PEMFC) plays an important role in high-quality water management. In this study, the removal effect of 3D wave channel and 2D straight channel for liquid water was studied by volume of fluid method. The dynamic behavior of droplet emerge from the gas diffusion layer (GDL) into the channel under the influence of gas flow was investigated. The effects of droplet growth, deformation, detachment, force, pore size on water critical behavior and water content in the channel are discussed. The results show that the 3D wave channel is superior to the removal of liquid water than the 2D straight channel. The increase of velocity is conducive to the discharge liquid water. While infinite increase of velocity will cause more parasitic power loss. The larger pore size of GDL is not advantageous to the performance of PEMFC, but the appropriate increase of pore size is conducive to the discharge of liquid water. The basic knowledge obtained in this study will help to deepen the understanding of droplet dynamics in PEMFC gas channels, and help to optimize the design and working conditions of these channels.

Programmed cell death protein 1 (PD-1) is a biomarker on the surface of cells that has a role in promoting self-tolerance by suppressing the inflammatory activity of T cells. In this work, one peptide of PD-1 was used as the template in molecular imprinting. The magnetic peptide-imprinted poly(ethylene-co-vinyl alcohol) composite nanoparticles (MPIP NPs) were characterized by dynamic light scattering (DLS), high-performance liquid chromatography (HPLC), Brunauer-Emmett-Teller (BET) analysis and superconducting quantum interference device (SQUID) analysis. Natural killer-92 (NK-92) cells were added to these composite nanoparticles and then incubated with human hepatoma (HepG2) cells. The viability and apoptosis pathway of HepG2 were then studied using cell counting kit-8 (CCK8) and the quantitative real-time polymerase chain reaction (qRT-PCR), respectively. These nanoparticles were found significantly enhance the activity of natural killer cells toward HepG2 cells by increasing expression of NK-kB, caspase 8 and especially caspase 3.

Three types of double perovskite La1-xPrxBa0.5Sr0.5Co1.5Fe0.5O5+δ(x=1,0.3,0) are prepared using the EDTA-citrate method and identified as solid oxide fuel cell (SOFC) cathodes. The microstructures, as well as electrochemical performances of La1-xPrxBa0.5Sr0.5Co1.5Fe0.5O5+δ (LPBSCF) and La2NiO4-impregnated LPBSCF (LN-LPBSCF) cathodes, are investigated in detail. An optimum impregnation amount of LN-LPBSCF (LN loading of 0.64 mg/cm2) electrode exhibits relatively lower electrode polarization resistance (Rp) and better stable performance as compared to that of pure LPBSCF electrode in symmetrical SOFCs. The maximum power density of LN-LPBSCF single cells is 800 mW/cm2 at 800 °C and demonstrates good stability for 100 h in short-term testing.

Here we report highly efficient, indium tin oxide (ITO)-free polymer solar cells (PSCs) with an ultrathin copper (Cu) film(~10 nm) coated with a thin layer of poly[(9,9-bis(3‘-(N,N-dimethylamino)propyl)-2,7-fluorene)-alt-2,7-(9,9-dioctylfluorene)] (PFN) as transparent electrode. Despite of its lower far-field transmittance of the electrode, the obtained ITO-free device based on the ultrathin Cu film can delivery higher absorption efficiency than that of the device based on ITO substrate in the long wavelength region, which can be attributed to the formation of metal resonant microcavity between the opaque back metal mirror (MoO3/Al electrode) and the transparent Cu film with high reflectance. As a result, polymer solar cells based on poly[[2,6'-4,8-di(5-ethylhexylthienyl)benzo[1,2-b;3,3-b]dithiophene][3-fluoro-2[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl]] (PTB7-Th) and [6,6]-phenyl C71-butyric acid methyl ester (PC71BM) blend show a high power conversion efficiency (PCE) of 8.21 %, comparable to that of the control device based on ITO electrode (with a PCE of 9.60% ). The results demonstrate that thermally evaporated Cu thin film electrode can be promising candidate to replace ITO for highly efficient PSCs, thus may open up the possibility for massive production of PSCs with low cost.

Nanomaterials have shown significant promise for enhancing the performance of composite materials and increasing their functionality for various industrial applications. This review explores the unique properties of nanomaterials, particularly carbon-based nanomaterials, and provides key findings in utilizing them to enhance composite performance. It highlights specific nano-based composite materials and their significant potential in advancing the field of nanocomposites. Challenges associated with nanocomposite production and utilization are also discussed, along with possible solutions to address them. Finally, the study provides recommendations for continued research and innovation in nanocomposites to fully unlock the benefits of these advanced materials for broader future applications.

Microbial electrochemical technologies (MET) rely on the presence of the metabolic activity of electroactive bacteria for the use of solid-state electrodes for oxidizing different kind of compound, that could lead to the synthesis of chemicals, bioremediation of polluted matrices, the treatment of contaminants of interest, as well as the recovery of energy. Keeping in mind those possibilities, since the beginning of the present century, there has been a growing interest in the use of electrochemical technologies for wastewater treatment, and if possible with simultaneous power generation. In the last years, there has been a growing interest to explore the possibility of merging MET with constructed wetlands, to offer a new option of intensified wetland system that could keep a high performance with a lower footprint. Based on that interest, this paper explains the general principles of MET, and the different known extracellular electron transfer mechanisms ruling the interaction between electroactive bacteria and potential solid-state electron acceptors. Also, the adoption of those principles for the development of MET set-ups for simultaneous wastewater treatment and power generation, and the challenges that the technology face. Ultimately, the most recent developments in set-ups that merges MET with constructed wetlands are presented and discussed.

This study investigates the performance and environmental impact of n-butanol blended with Jet-A fuel in turbo-engines, aiming to assess its viability as a sustainable aviation fuel (SAF). The research involves experimental testing of various blends, ranging from low to high concentrations of methanol, to determine their effects on engine performance and emissions. The experimental setup includes comprehensive measurements of engine parameters such as thrust, fuel consumption rates, and exhaust gas temperatures. Emissions of nitrogen oxides (NOx), particulate matter (PM), carbon monoxide (CO), and unburned hydrocarbons (HC) are also analysed to evaluate environmental impacts. Key findings indicate that n-butanol/Jet-A blends can significantly enhance combustion efficiency and reduce emissions compared to conventional Jet-A fuel. Higher n-butanol concentrations lead to improved thermal efficiency and lower NOx and CO emissions. However, PM emissions slightly increase with higher methanol content. The study underscores the potential of n-butanol as a SAF for turbo-engines, highlighting its ability to mitigate environmental impacts while maintaining or improving engine performance. This research supports the feasibility of integrating n-butanol into Jet-A blends for turbo-engine applications, emphasizing its role in achieving more environmentally friendly aviation operations.

Nowadays, the increasingly serious environmental pollution and energy problems urgently require internal combustion engine-based transportation vehicles to upgrade or replace, so the new energy transportation vehicles based on hybrid power and fuel cells have gradually stepped on the stage and continue to innovate. The shipping industry is one of the main sources of global greenhouse gas emissions. The development of clean energy ships represented by fuel cells has attracted wide attention. Fuel cell has the advantages of clean, pollution-free and low noise, but it has some disadvantages such as insufficient dynamic response performance and fast performance decay. Limited by the characteristics of a single energy source, a variety of energy sources and bidirectional DC converters are usually mixed together to form a hybrid ship to improve the flexibility, stability and economy of the ship, and enhance its adaptability to complex sea conditions through the reconfiguration of power system energy. Taking fuel cell ferry "FCS Alsterwasser" as the research object, this study proposed an improved equivalent minimum hydrogen consumption energy management strategy based on fuzzy logic control. First, the power system of the modified mother ship was simulated, and a hybrid power system including fuel cell, lithium iron phosphate battery and supercapacitor was proposed. Then, the dynamic system simulation model and double closed loop PI control model are established in MATLAB/Simulink, and the reliability of the model is verified by the simulation analysis of charge and discharge characteristics. Then, the feasibility of the proposed method is demonstrated by designing simulation experiments based on typical working conditions of the mother ship. The simulation results show that under the premise of meeting the load requirements, the control strategy designed in this paper has a better optimization effect than the S-type penalty function in terms of lithium battery power, lithium battery SOC, bus voltage stability and equivalent hydrogen consumption, which improves the stability and economy of the power system, and has certain engineering practical value.

The susceptible-infected-recovered-vaccinated-deceased (SIRVD) epidemic compartment model extends the SIR model to include the effects of vaccination campaigns and time-dependent fatality rates on epidemic outbreaks. It encompasses the SIR, SIRV, SIRD, and SI models as special cases, with individual time-dependent rates governing transitions between different fractions. We investigate a special class of exact solutions and accurate analytical approximations for the SIRVD and SIRD compartment models. While the SIRVD and SIRD equations pose complex integro-differential equations for the rate of new infections and the fractions as a function of time, a simpler approach considers determining equations for the sum of ratios for given variations. This approach enables us to derive fully exact analytical solutions for the SIRVD and SIRD models. For nonlinear models with a high-dimensional parameter space, such as the SIRVD and SIRD models, analytical solutions, exact or accurately approximative, are of high importance and interest: not only as suitable benchmarks for numerical codes, but especially as they allow us to understand the critical behavior of epidemic outbursts as well as the decisive role of certain parameters. In the second part of our study, we apply a recently developed analytical approximation for the SIR and SIRV models to the more general SIRVD model. This approximation offers accurate analytical expressions for epidemic quantities, such as the rate of new infections and the fraction of infected persons, particularly when the cumulative fraction of infections is small. The distinction between recovered and deceased individuals in the SIRVD model affects the calculation of the death rate, which is proportional to the infected fraction in the SIRVD/SIRD cases but often proportional to the rate of new infections in many SIR models using a posteriori approach. We demonstrate that the temporal dependence of the infected fraction and the rate of new infections differs when considering the effects of vaccinations and when the real-time dependence of fatality and recovery rates diverge. These differences are highlighted for stationary ratios and gradually decreasing fatality rates. \Revised{The case of stationary ratios allows one to construct a new powerful diagnostics method to extract analytically all SIRVD model parameters from measured COVID-19 data of a completed pandemic wave.

Improper disposal of waste plastic has caused serious ecological and environmental pollution problems. Transforming plastics into high value-added chemicals can not only achieve efficient recycling of waste plastics, but also an effective way to control white pollution. The catalyst selectively breaks the C-C bond of polyolefin plastic under heat treatment and converts it into liquid fuel, thus realizing sustainable recycling of plastics and has a good development prospect. This review provides a detailed overview of the current development of catalytic pyrolysis, catalytic hydrolysis, solvent decomposition and supercritical hydrothermal liquefaction for cracking plastics to make fuel oil. The reaction mechanism, influencing factors and promoting effects of catalysts in various degradation technologies are analyzed and summarized and the latest proposed tandem reaction for degrading plastics is briefly introduced. Finally, some optimization paths of waste plastic pyrolysis to fuel oil technology are proposed: synergies between mixed raw materials, in-depth exploration of catalysts, design and manufacture of reactors that match the pyrolysis technology. All these are important research directions for promoting the industrialization of plastic pyrolysis to fuel oil.

The leather industry is one of the most polluting industries in the world due to the large amounts of waste following the raw hides processing, but also due to the high content of chemicals present in their composition. The main problem of chromium-tanned leather solid waste is related to their storage, because of the ability of chromium to leach in soil or water, and also owing to the high ability of trivalent chromium to oxidize to its toxic form, hexavalent chromium. The purpose of this study is to present the latest methods for extracting trivalent chromium from the composition of solid leather wastes. The extraction methods identified in the present study are based on acid/basic/enzymatic hydrolysis and substitution with the help of organic chelators (organic acids and organic acid salts). In addition, the study includes a comparative analysis between the advantages and disadvantages of each identified extraction method. At the same time, the study also presentes alternative chromium extraction methods based on the combination of conventional extraction methods and ultrasound-assisted extraction.

Soil microbial fuel cells (sMFC) are a novel technique that use organic matters in soils as an alternative energy source. External resistance (ER) is a key factor influencing sMFC performance and, furthermore, alters the soil’s biological and chemical reactions. However, little information is available on how the microbial community and soil component changes in sMFC with different ER. Therefore, the effects of anodes of sMFC at different ER (2000 Ω, 1000 Ω, 200 Ω, 80 Ω and 50 Ω) were examined by measuring organic matter (OM) removal efficiency, trace elements in porewater and bacterial community structure in contaminated paddy soil. The results indicated that ER has significant effects on sMFC power production, OM removal efficiency and bacterial beta diversity. Moreover ER influences iron, arsenic and nickel concentration as well in soil porewater. In particular, greater current densities were observed at lower ER (2.4mA, 50Ω) compared to a higher ER (0.3mA, 2000Ω). The removal efficiency of OM increased with decreasing ER whereas it decreased with soil distance away from the anode. Furthermore, principal coordinate analysis (PCoA) revealed that ER may shape the bacterial communities that develop in the anode vicinity but have minimal effect on that of the bulk soil. The current study illustrates that lower ER can be used to selectively enhance the relative abundance of electrogenic bacteria and lead to high OM removal.

Diesel is consistently a very popular fuel for internal combustion engines. Its consumption in the European Union has been rising over recent years, as has the number of engines increasingly sensitive to fuel contamination. One of the most important parameters affecting diesel quality is water content. Although its exceedances of the standard’s permissible amount are not common, they carry the risk of serious damage to expensive, modern fuel injection systems. Current methods of measuring water content require both specialised personnel and equipment, as well as transporting the sample to a suitable laboratory. The research presented in this paper was aimed at verifying whether it would be possible to test the moisture content of diesel using impedance spectroscopy. Once refined, such measurement method could be used in situ. Analysing the properties of diesel is challenging, mainly because many types of the fuel are sold, the chemical composition of which is always a well-guarded manufacturer’s secret. The experimental results obtained on many types of commercially available diesel show that it is possible to use impedance spectroscopy to estimate the water content of different types of diesel fuel. The measurement accuracy achieved makes it possible to detect approaching or exceeding the permissible water content.

Multi-rotor drones, a kind of unmanned equipment which is widely used in military, commercial consumption and other fields, has been developed very rapidly in recent years. However, their short flight time has hindered the expansion of their application range. This can be addressed by utilizing hydrogen fuel cells, which exhibit high energy density, strong adaptability to ambient temperature, and no pollution emissions, as the power source. Accordingly, the application of hydrogen fuel cells as the power source in multi-rotor drones is a promising technology that has attracted significant research attention. This paper summarizes the development process of hydrogen fuel cell mul-ti-rotor drones and analyzes the key obstacles that need to be addressed for the further development of hydrogen fuel cell multi-rotor drones, including structural lightweight, hydrogen storage methods, energy management strategies. Additionally, prospects for the future development of hydrogen fuel cell multi-rotor drones are presented.

Phased injection of natural gas into internal combustion marine engines is a promising solution for optimizing performance and reducing harmful emissions, particularly unburned methane, a potent greenhouse gas. This innovative practice distinguishes itself from continuous injection because it allows for more precise control of the combustion process with only a slight increase in system complexity. By synchronizing the injection of natural gas with the intake and exhaust valve opening and closing times while also considering the gas path in the manifolds, methane release into the atmosphere is significantly reduced, making a substantial contribution to efforts to address climate change. Moreover, phased injection improves the efficiency of marine engines, resulting in reduced overall fuel consumption, lower fuel costs, and increased ship autonomy. This technology has been tested on a single-cylinder, large-bore, four-stroke research engine designed for marine applications, operating in dual-fuel mode with diesel and natural gas. Performance was compared with that of the conventional continuous feeding method. Evaluation of the effect on equivalent CO2 emissions indicates a potential reduction of up to approximately 20%. This reduction effectively brings greenhouse gas emissions below those of the diesel baseline case, especially when injection control is combined with supercharging control to optimize the air-fuel ratio.

In order to obtain higher thermoelectric and mechanical properties in non-polar thermoplastic vulcanizates (TPVs), the Butyl rubber/Polypropylene (TPVs)/hydroxylated graphene (HGE) composites with nanosheet network were prepared through masterbatch technique and based on thermodynamic calculations, using polypropylene-graft-maleic anhydride (PP-MA) as a compatibilizer. The FTIR and Raman spectra revealed the introduced maleic anhydride group on PP-MA can form strong interfacial interaction with hydroxyl-containing functional groups on HGE. Morphology study indicated the rubber particles in the composites occupied the most volume of the PP phase, as expected to hinder the aggregation of HGE and form the effective nanosheet network. The nanosheet network can be combined with the IIR cross-linked particles during the dynamic vulcanization process to improve the interface bonding between PP and IIR, thus increasing the tensile strength of TPVs. When the content of HGE reached the percolation threshold (2 wt.%), the nanosheet network of HGE was formed, and the AC conductivity, dielectric permittivity and thermal conductivity increased sharply. The prepared TPVs/HGE nanocomposites have significantly improved in mechanical properties, thermal properties and dielectric properties, which provides a guarantee for their potential application as multifunctional TPVs polymers.

Cathode materials based on SrCoO3- perovskite-type oxides hold great potential, given the huge oxygen permeability exhibited by the cubic phase of this oxide, which must be stabilized though suitable cationic substitutions. We present here two novel materials of the series Sr1-xYxCoO3- (x= 0.1, 0.2), prepared by solid state reactions. The crystalline structure was explored by neutron powder diffraction. At RT, we identified a subtle tetragonal superstructure, yet preserving the wanted framework of vertex-sharing CoO6 octahedra. A noteworthy result of the neutron analysis is the presence of conspicuous amounts of oxygen vacancies, ordered in layers and responsible for the formation of the mentioned superstructure. The stability was investigated by thermal analysis, using thermogravimetry (TGA). The electrical conductivity gave a maximum value of 800 °C of 122 S·cm–1. To determine the resistance associated with the oxygen reduction reaction (ORR), electrochemical impedance spectroscopy as a function of temperature was carried out, finding a value for the activation energy of Ea= 0.82 eV. This is a much lower value than that usually obtained for cathodes with a high catalytic activity for the oxygen reduction reaction. In single-cell tests, the materials generated a power density up to 0.25 Wcm−2 at 800ºC, using pure H2 as fuel. All these features make this perovskite a suitable candidate as cathode material in intermediate-temperature SOFCs

Microbial fuel cells (MFCs) offer sustainable solutions for various biotechnological applications and are a crucial area of research in biotechnology. MFCs can effectively treat wastewater and biodiesel waste by decomposing organic matter and generating electricity. Certain Pseudomonas species possess extracellular electron transfer (EET) pathways, enabling them to transfer electrons from organic compounds to the MFC's anode. Moreover, Pseudomonas species can grow under low oxygen conditions, which is advantageous considering that the electron transfer process in an MFC typically leads to reduced oxygen levels at the anode. This study focuses on evaluating MFCs inoculated with a new Pseudomonas species, grown with 1 g.L-1 glycerol, a common byproduct of biodiesel production. Pseudomonas sp. BJa5 exhibited a maximum power density of 39 mW.m-2. Also, the observed voltammograms and genome analysis indicate the potential production of novel redox mediators by BJa5. Additionally, we investigated the bacterium's potential as a synthetic biology non model chassis. Through testing various genetic parts, including constitutive promoters, replication origins, and cargos using pSEVA vectors as a scaffold, we assessed the bacterium's suitability. Overall, our findings offer valuable insights into utilizing Pseudomonas spp. BJa5 as a novel chassis for MFCs. Synthetic biology approaches can further enhance the performance of this bacterium in MFCs, providing avenues for improvement.

Oxygen and hydrogen mobility are among the important characteristics for operation of solid oxide fuel cells, permselective membranes and many other electrochemical devices. This, along with other characteristics, enables reaching a high power density of solid oxide fuel cells and a high oxygen or hydrogen permeation fluxes for membranes. This work focuses on oxygen and hydrogen diffusion of mixed ionic (oxide ionic or/and protonic) – electronic conducting materials for these devices and its role in the performance. Ionic transport properties of conventional and state-of-the-art materials are reviewed.

This paper presents the novel development of a shape memory polymer foam based on polymer-polymer nanocomposites. Herein, polylactide (PLA)/biosourced polyamide (PA) foams are fabricated by in-situ fibrillation of polymer blends and subsequent supercritical CO2 foaming technique. In this system, PLA serves as a shape memory polymer to endow this foam with a shape memory effect (SME), and in-situ generated PA nanofibers are employed to reinforce the PLA cell walls and provide an additional permanent phase. Concentration of PA, 5 wt.%, is chosen to form an entangled nanofibrillar network. Foams of PLA/PA nanoblends with the same content of constituents are fabricated to reveal the effect of minor phase morphology on the cell structure and shape memory behavior of polymer foams. Profiting from the reinforcing effect of PA nanofibers, the PLA/PA nanocomposite foam exhibits smaller foam cells, a narrower cell size distribution and a comparable cell concentration than the PLA/PA nanoblend foam. In addition, PA nanofibers, unlike PA nanodroplets, favor the shape fixation ratio and recovery ratio and shorten the shape recovery time.

A dioxomolybdenum catalyst [(MoO2Cl2-O-MoO2Cl2)(L)] (1) (with L (1S,2S)-N,N´-bis(2-pyridinecarboxamide)-1,2-cyclohexane) was prepared and used as catalyst for the desulfurization of a multicomponent model fuel containing the most refractory sulfur compounds in real fuels. This complex showed to have a high efficiency to oxidize the aromatic benzothiophene derivative compounds present in fuels, mainly using a biphasic 1:1 model fuel/MeOH system. This process conciliates catalytic oxidative and extractive desulfurization, occurring the oxidation of the sulfur compounds in the polar organic solvent. The oxidative catalytic performance of (1) showed to be influenced by the presence of water in the system. Using 50% aq. H2O2 it was possible to reuse the catalyst and the extraction solvent MeOH during ten consecutive cycles without loss of desulfurization efficiency.

Medium polarity plays a crucial role in charge-transfer processes and electrochemistry. The added supporting electrolyte in electrochemical setups, essential for attaining the needed electrical conductivity, sets challenges for estimating medium polarity. Herein, we resort to Lippert–Mataga–Ooshika (LMO) formalism for estimating the Onsager polarity of electrolyte organic solutions pertinent to electrochemical analysis. An amine derivative of 1,8-naphthalimide proves to be an appropriate photoprobe for LMO analysis. An increase in electrolyte concentration enhances the polarity of the solutions. This effect becomes especially pronounced for low-polarity solvents. Measured refractive indexes provide a means for converting Onsager to Born polarity, which is essential for analyzing medium effects on electrochemical trends. This study demonstrates a robust optical means, encompassing steady-state spectroscopy and refractometry, for characterizing solution properties important for charge-transfer science and electrochemistry.

Integrated photovoltaic-fuel cell (IPVFC) systems have the potential to contribute to sustainable energy production for grid and off-grid applications. While there are studies focusing on fundamental science and designs for IPVFC systems, there are scarcely studies that have focused on the manufacturability of IPVFC systems, which is certainly the pathway for commercialisation of the systems. This study explores manufacturing strategies that can be considered for exploiting a family of eleven IPVFC systems. A survey and systems thinking were used to investigate the potential modularisation and supply chain management to achieve optimal lean and agile manufacturing strategy. Results show that the Photovoltaic-Thermal-Separate Converter/Inverter-Battery System received 25% of the responses. The optimal manufacturing strategy depends on the overall business strategy of the firm. Although 17% preference for System 1 is significant compared to four members of the family of IPVFC systems (Systems 2, 6, 8 and 9) that received only 2% of the responses, it indicates that there is a likelihood that the demand for System 1 will be among the top 42% of the total demand. Overall, this study provides new insights on how the family of IPVFC systems can contribute to realising greater access to clean energy, by extension contributing to the net-zero efforts using solar energy and solar hydrogen.

Excess energy from photosynthesis can be collected through biophotovoltaic platforms to generate green electrical power. This research evaluated the in-situ performance of different CAM (Crassulaceae acid metabolism) plants from Calama city located in the Atacama Desert for energy recovery as biophotovoltaic cell (BPV) using AISI 316L and Cu as electrodes. The species evaluated were Aloe perfoliata, Cereus jamacaru, Austrocylindropuntia subulata, Agave potatorum, Malephora crocea, and Kalanchoe daigremontiana. The results indicate that K. daigremontiana can be used as in-situ BFV because it has a maximum cell potential of 0.248 V and a minimum of 0.139 V with a recurrence close to 89% in the ranges [0.2 - 0.25] V. This is one of the few investigations that evaluate the potential of native CAM plants as BFV energy sources, providing new knowledge for the development of sustainable alternatives for horticultural crop production systems.

Addressing the pressing challenge of global warming, reducing greenhouse gas emissions in the transportation sector is a critical imperative. Battery and fuel-cell electric vehicles have emerged as promising solutions for curbing emissions in this sector. In this study, we conducted a comprehensive life cycle assessment (LCA) for typical passenger vehicles, heavy duty trucks and city buses using either proton-exchange membrane fuel cells or Li-ion batteries with different cell chemistries. To ensure accuracy, we supplemented existing studies with data from the literature, particularly for the recycling phase, as database limitations were encountered. Our results highlight that fuel cell and battery systems exhibit large emissions in the production phase. Recycling can significantly offset some of these emissions, but a comparison of the technologies examined revealed considerable differences. Overall, battery electric vehicles consistently outperform fuel cell electric vehicles regarding absolute greenhouse gas emissions. Hence, we recommend prioritizing battery electric over fuel cell vehicles. However, deploying fuel cell electric vehicles could become attractive in a hydrogen economy scenario where other factors, e. g. the conversion and storage of surplus renewable electricity via electrolysis, become important.

Graphene hybrid-filler polymer composites have emerged as prominent materials that revolutionize heavy industries. This study encapsulates the in-depth analysis of different influential factors such as filler/graphene type, aspect ratios, dispersion methods, filler-matrix compatibility, fiber orientation, synergistic effects, different processing techniques, and post-curing conditions that affect the processing, properties and determine the resultant applications of graphene hybrid polymer composites. Additionally, it discusses the substantial role of graphene collaboration with other fillers such as carbon nanotubes, silica, nano-clays and metal oxides to produce functionalized hybrid polymer composites with synergistically enhanced tailored properties to offer solutions for heavy industries like aerospace, automotive, electronics, and energy harvesting. The review concludes with some suggestions and outlook on the future of these composite materials by emphasizing the need for continued research to fully optimize their potential.

Two region asymmetric polymers PR2F and PR1F with three repeat units of A-D-A, π-D-A, and π-D-π along the polymer backbone were attained by polymerizing different fluorinated benzothiadiazole-thiophene units, FBT-T and 2FBT-T units (A–π), with benzodithiophene unit (D), respectively. Here, the new region asymmetric polymers were in contrast to the traditional polymers featuring a D–A or D–π–A–π backbone. Both the region asymmetric polymers showed a low lying of HOMO energy level in relation to that of the PC61BM acceptor and then obtained the high open-circuit voltage of ~1 V in both PR2F and PR1F devices. Bulk-heterojunction devices based on PR2F with difluorinated BT exhibited an appreciable power conversion efficiency (PCE) of 4.73% due to the relatively high and balanced charge carrier mobilities, while the mono-fluorinated BT polymer PR1F-based devices gave a lower PCE of 2.92%. These results indicate that the region asymmetric conjugated polymer is a promising class of materials for polymer solar cell applications, and it is significant to further understand the influence of polymer structure on optoelectronic properties.

Umbilical cord-derived mesenchymal stem cells (UC-MSCs) are reported to have features intermediate between fetal and adult mesenchymal cells. Hence, UC-MSCs were cocultured with chondrocytes and Schwann cells to induce differentiation because of their flexible differentiation potential. US-MSCs were obtained from umbilical cords and cells at second passage were used in the experiments. Atelocollagen sponge was used as the scaffold for coculture; a horizontal, interactive coculture plate with a 0.6-μm pore size filter was placed between the connected vessels. US-MSCs were cocultured separately with chondrocytes and Schwann cells and culture alone served as a control. Five weeks after induction of differentiation, each specimen was evaluated histologically. In specimens cocultured with chondrocytes and the controls, cartilage tissues were detected using hematoxylin-eosin and toluidine blue staining. Cells positive for S100 protein were detected in the specimens cocultured with Schwann cells, but not in the controls. UC-MSCs were easily induced to differentiate into chondrocytes and neural cells by coculture. This indicates that continuously-shared humoral factors were effective in inducing differentiation of UC-MSCs. Coculture appears to be a potential technique for tissue regeneration using MSCs.

Tinnitus is a common phantom auditory percept, believed to be related to plastic changes in the brain due to hearing loss. However, tinnitus can also occur in absence of any clinical hearing loss. Then, since there is no hearing loss, the mechanisms that drive plastic changes remain largely enigmatic. Previous studies showed subtle differences in sound-evoked brain activity associated with tinnitus in subjects with tinnitus and otherwise, normal hearing, but the results are not consistent across studies. Here, we aim to investigate those differences using monaural rather than binaural stimuli. Sound-evoked responses were measured using functional magnetic resonance imaging (MRI) in participants with and without tinnitus. All participants had clinically normal audiograms. The stimuli were pure tones with frequencies between 353 and 8000 Hz, presented monaurally. A Principal Component Analysis (PCA) of the response in the auditory cortex revealed no difference in tonotopic organization, which confirmed earlier studies. A GLM analysis showed hyperactivity in the lateral areas of the bilateral auditory cortex. Consistent with the tonotopic map, this hyperactivity mainly occurred in response to low stimulus frequencies. This may be related to hyperacusis, which was associated with tinnitus found in the parahippocampus. This may reflect an interference between tinnitus and spatial orientation.

We investigated the influence of the fuel change, from pure hydrogen to hydrogen-ammonia mixture at different percentage, on the electrochemical behaviour of 50 mm in diameter Solid Oxide Fuel Cells (SOFC) with sputtered thin buffer layers of Gd doped Ceria, varying the working temperatures from 800°C to 650°C. The results show that the performances of the cells are not affected by the fuel change for the high working temperatures (800°C and 750°C). As an example, a power density value of 802 mW∙cm-2 at 1 A∙cm-2 is found when directly feeding the cell with 8 Nml∙min-1cm-2 of ammonia and with an equivalent flowrate of 12 Nml∙min-1cm-2 of H2. These power density output values are comparable to those obtained in industrial State of Art (SoA) SOFC cells with screen printed buffer layers fed with higher hydrogen flowrates, thanks to the improved electrochemical performances obtained in the case of cells with sputtered thin buffer layers of Gd doped Ceria. At lower working temperatures (700°C and 650°C), slight changes in the electrochemical behaviour of the cells are observed. Nevertheless, also in this temperature range, we obtain an output current density value of 0.54 A∙cm-2 in pure ammonia flowrate of 12 Nml min-1cm-2, at 800 mV and 700°C, equal to the value observed in SoA button cells with industrial screen printed GDC barrier layer fuelled with 16 Nml∙min-1cm-2 of H2. These results pave the way towards the use of innovative SOFC structures with sputtered thin buffer layers fuelled by ammonia.

This paper reviews the requirements for the production, quality, and quality assurance of solid recovered fuels (SRF) that are increasingly used for the substitution of fossil fuels in the indus-trial utilities. The economical, technological and environmental aspects should be considered before using SRF as an alternative fuel. In general, the most important factors determining the commercial production of SRF referred to the calorific values and their available amounts adopted in the starting materials. Furthermore, the low-melting impurities and undesired constituents/elements, including chlorine, sulfur, potassium and sodium, may pose negative impacts on air pollutant emission and slagging & fouling in the process utilities. In this regard, the vent emitted from the industrial utilities must comply with the effluent standards of station-ary sources like particulate, sulfur oxides, nitrogen oxides, heavy metals (e.g., lead, cadmium, and mercury) and dioxins. For these reasons, this work will summarize the legal or regulatory requirements under development in Asian countries (i.e., Japan, South Korea, and Taiwan) and European Union (EU). Finally, the outlook of solid recovered fuel (SRF) in the waste manage-ment and industrial sectors will be addressed to echo the sustainable development goals (SDGs).

Novel bio-inspired materials have gained recently great attention, especially in medical applications. Applying sophisticated design and engineering methods, various polymer-polymer hybrid systems with outstanding performance have been developed in last decades. Hybrid systems composed of bioelastomers and hydrogels are very attractive due to their high biocompatibility and elastic nature for advanced biomaterials used in various medical applications such as drug delivery systems and scaffolds for tissue engineering. Herein, we describe the advances in current state-of-the-art design, properties and applications of polymer-polymer hybrid systems in medical applications. Bio-inspired functionalities, including bioadhesiveness, injectability, antibacterial properties and degradability applicable to advanced drug delivery systems and medical devices will be discussed in a context of future efforts towards development of bioinspired materials.

Nanostructured polymer dispersed liquid crystals (nano-PDLCs) are transparent and optically isotropic materials, in which submicron-sized liquid crystal (LC) domains are dispersed within a polymer matrix. Nano-PDLCs can induce their birefringence by applying an electric field (E-field) based on reorientation of LC molecules. If nano-PDLCs are utilized as light scattering-less birefringence memory materials, it is necessary to suppress the relaxation of LC molecules orientation after removal of the E-field. We focused on a ferroelectric smectic A (SmA) to suppress the relaxation of LC molecules due to their layered structure and high viscosity. Although nano-PDLCs require a strong E-field to reorient LC molecules due to the anchoring effect on the LC/polymer interface, the required field strength can be reduced by using a ferroelectric smectic A (SmAF) LC with a large dielectric constant. In this study, we fabricated a nano-PDLC by irradiating an ultraviolet light to a mixture comprising of a SmAF LC, photocurable monomers and a photo-initiator and its electro-birefringence effect was evaluated using a polarizing optical microscopy. After removal of an E-field, enhanced memory effect was observed on the sample using SmAFLC comparing to nematic LC based nano-PDLCs. (193 words/ 200 words)

Chemical flooding methods are used to recover the remaining oil after water flooding, and surfactant-polymer (SP) flooding is an important chemical flooding technology. It is of great significance to design and screen high-performance oil displacement agents in order to overcome the increasingly challenging high temperature (>70 ℃) and high salinity (>10,000 mg/L) reservoirs. Based on the characteristics of high temperature (70 ℃) and high salinity (151,000 mg/L) in the Qinghai Gasi reservoir, the performance of the SP flooding system was studied. This study considered interfacial tension, emulsification, viscosity, compatibility, and oil displacement efficiency. The selected formula demonstrated high resistance to both salinity (151,000 mg/L) and temperature (70 ℃), characterized by a low oil-water interfacial tension (10-2 mN/m) and high viscosity (18.13 mPa.s). After water flooding achieved an oil recovery rate of 64.64%, the subsequent replacement rate of crude oil increased by 26.95%, confirming that SP flooding can be used as a technology for enhancing oil recovery in high-temperature, high-salinity reservoirs represented by Qinghai Gasi reservoirs.

Background: Monocyte-derived dendritic cells (mo-DCs) play a vital role in the innate immune response by activating Th17 cells, which in turn release the pro-inflammatory cytokine IL-17. We hypothesised that following repetitive mechanical strain, tenocytes activate monocyte-derived dendritic cells, which in turn, drive the pathogenesis of tendinopathy. Aim: The aim of the study was to determine if monocyte-derived dendritic cells are upregulated in a human tendinopathy model. Method: Torn supraspinatus tendon and matched intact subscapularis tendon samples were collected from 7 patients undergoing arthroscopic shoulder surgery. Healthy control samples of subscapularis tendon were collected from 5 patients undergoing arthroscopic stabilization surgery. Tendon biopsy samples were evaluated immunohistochemically by quantifying the presence of monocyte-derived dendritic cells (CD11C and CD206). Results: Tendinopathic tendon samples exhibited significantly greater (2-3-fold) monocyte-derived dendritic cell expression when compared with healthy control tissue (P < .05). Conclusion: This study provides evidence for a monocyte-derived dendritic cell upregulation in early-stage human tendinopathy.

Cross-linked polyethylene (XLPE) is a highly all-important material renowned for its exceptional physical and chemical properties, and it is extensively utilized in various industries such as con-struction, piping, cable insulation and medical equipment. The cross-linking process of polyethylene involves chemical or physical bonding of polymer chains to enhance its resistance to heat, chemicals and mechanical stress. This study offers a comprehensive overview of recent research and potential advancements in this field, with a particular focus on the development of efficient techniques and environmentally sustainable cross-linking systems. It evaluates the opportunities and challenges faced by cross-linked polyethylene materials across diverse applications, providing valuable insights for future research in this area.