High-energy small electron beams generated by linear accelerators are used for radiotherapy of localized superficial tumors. The aim of the present study is to assess the dosimetric performance under small radiation therapy electron beams of the novel PTW microSilicon detector by comparison with commercially available dosimeters. Relative dose measurements of circular fields with 20, 30, 40 and 50 mm aperture diameters were performed for 4 to 12 MeV energy range of electron beams generated by an Elekta Synergy linac. Percentage depth dose, transverse profiles and output factors normalized to the 10 × 10 cm2 reference field were measured. All dosimetric data were collected in a PTW MP3 motorized water phantom at SSD of 100cm by using the novel PTW microSilicon detector. The PTW diode E and the PTW microDiamond were also used in all beam aperture for benchmarking. Data for the biggest field size were also measured by the PTW Advanced Markus ionization chamber.Measurements performed by the microSilicon are in good agreement with the reference values for all the tubular applicators and beam energies, within the stated uncertainties. This confirms the reliability of the microSilicon detector for relative dosimetry of small radiation therapy electron beams collimated by tubular applicators.

During the last decades the quantitative description of electrical and magnetotransport properties of solid-state materials has been a remarkable challenge in materials science. Recently, the discovery of a novel class of materials, the topological semimetals, has led to a growing interest for the full understanding of their magnetotransport properties. In this review, the strong interplay among topology, band structure and carrier mobility in recently discovered high carriers mobility topological semimetals is discussed and their effect on their magnetotransport properties is outlined. The huge magnetoresistance effect, especially in the Hall transverse configuration, and a new version of a three-dimensional quantum Hall effect observed in high-mobility Weyl and Dirac semimetals are reviewed. The design of novel quantum sensors based on solid-state semimetals is also encouraged.

Thermal simulations are an important part in the design of electronic systems, especially as systems with high power density become common. In simulation-based design approaches, a considerable amount of time is spent by repeated simulations. In this work, we present a proof-of-concept study of the application of convolutional neural networks to accelerate those thermal simulations. The goal is not to replace standard simulation tools but to provide a method to quickly select promising samples for more detailed investigations. Based on a training set of randomly generated circuits with corresponding Finite Element solutions, the full 3D steady-state temperature field is estimated using a fully convolutional neural network. A custom network architecture is proposed which captures the long-range correlations present in heat conduction problems. We test the network on a separate dataset and find that the mean relative error is around 2 % and the typical evaluation time is 35 ms per sample ( 2 ms for evaluation, 33 ms for data transfer). The benefit of this neural-network-based approach is that, once training is completed, the network can be applied to any system within the design space spanned by the randomised training dataset (which includes different components, material properties, different positioning of components on a PCB, etc.).

Effective and rapid mixing is essential for various chemical and biological assays. The present work reports a simple and low-cost micromixer based on magnetofluidic actuation. The device takes advantage of magnetoconvective secondary flow, a bulk flow induced by an external magnetic field, for mixing. A paramagnetic stream of diluted ferrofluid and a non-magnetic stream are introduced to a straight microchannel. A permanent magnet placed next to the microchannel induced a non-uniform magnetic field. The magnetic field gradient and the mismatch in magnetic susceptibility between the two streams create a body force, which leads to rapid and efficient mixing. The micromixer reported here could achieve a high throughput and a high mixing efficiency of 90 % in a relatively short microchannel.

Nanoporous membranes promise energy-efficient water desalination. Hexagonal boron nitride (h-BN), like graphene, exhibits outstanding physical and chemical properties, making it a promising candidate for water treatment. We employed Car–Parrinello molecular dynamics simulations to establish accurate modeling of Na+ and Cl- permeation through hydrogen passivated nanopores in graphene and h-BN membranes. In these complex systems the classical potentials cannot properly account for the physics at play. We demonstrate that ion separation works well for the h-BN by imposing a barrier of 0.13 eV and 0.24 eV for Na+ and Cl- permeation respectively, compared to the graphene where the Cl- ion faces a negative barrier of 0.68 eV and is prone toward blockade and Na+ permeation is associated with a slightly negative barrier of 0.03 eV. From the change in the solvation shell, we get the following trend: Na/h-BN > Na/G > Cl/G > Cl/h-BN. We argue that the trend in the permeation barrier changes to Cl-h-BN > Na-h-BN > Na-G > Cl-G due to a combination of several interactions, including the distortion of the water network induced by the ions, the ion-water interaction, and the ion-nanopore interaction. Overall, the desalination performance of h-BN surpasses that of their graphene counterparts.

Surface acoustic wave (SAW) is effective for the manipulation of fluids and particles in microscale. The current approach of integrating interdigitated transducers (IDTs) for SAW generation into microfluidic channels involves complex and laborious microfabrication steps. These steps often require the full access to clean room facilities and hours to align the transducers to the precise location. This work presents an affordable and innovative method for fabricating SAW-based microfluidic devices without the need of clean room facilities and alignment. The IDTs and microfluidic channels are fabricated in the same process and thus precisely self-aligned in accordance with the device design. With the use of the developed fabrication approach, a few types of different SAW-based microfluidic devices have been fabricated and demonstrated for particle separation and active droplet generation.

A single mode waveguide grating coupler based on multiple Si-SiO₂ pairs onto Si substrate has been designed. Numerical analysis has been carried out to calculate optimum thickness of the layers of Si-SiO₂ that ensures the constructive interference between reflected waves and actual guided wave for high coupling efficiency. Based on the results, an optimal design is developed and modeled by using a 2-D finite difference time domain (2-D FDTD) simulator that dictates a coupling efficiency of as much as 78% (-1.07 dB) at the wavelength of 1550 nm, and a 1-dB bandwidth of 77 nm. The numerical method will be useful to calculate the optimum thicknesses of the layers for any reflector based grating coupler of different materials.

Hydrogenated amorphous silicon (a-Si:H) can be produced by plasma-enhanced chemical vapour deposition (PECVD) of SiH4 (Silane) mixed with Hydrogen. The resulting material shows outstanding radiation resistance properties and can be deposited on a wide variety of different substrates. These devices have been used to detect many different kinds of radiation namely: MIPs, x-rays, neutrons and ions as well as low energy protons and alphas. However, MIP detection using planar diodes has always been difficult due to the unsatisfactory S/N ratio arising from a combination of high leakage current, high capacitance and a limited charge collection efficiency (50% at best for a 30 µm planar diode). To overcome these limitations the 3D-SiAm collaboration proposes to use a 3D detector geometry. The use of vertical electrodes allows for a small collection distance to be maintained while conserving a large detector thickness for charge generation. The depletion voltage in this configuration can be kept below 400 V with consequent reduction in the leakage current. In this paper, following a detailed description of the fabrication process, the results of the tests performed on the planar p-i-n structures made with ion implantation of the dopants and with carrier selective contacts will be illustrated.

The diamagnetic levitation technique can be applied to non-destructive testing for identifying cracks and defects in magnetic materials. Pyrolytic graphite is a material that can be leveraged in micromachines due to its no-power diamagnetic levitation on a permanent magnet (PM) array. However, the damping force applied to pyrolytic graphite prevents it from maintaining con-tinuous motion along the PM array. This paper investigates the in-plane motion and damping characteristics of pyrolytic graphite sheets on the PM array. The centroid of pyrolytic graphite will maintain a stable levitation when positioned on the intersecting point of the PM array. Fur-thermore, the in-plane motion of two different pyrolytic graphite sizes - PG10 (10×10×0.5mm3) and PG20 (20×20×0.5mm3) - has revealed that the in-plane forces applied to them are approximately 61.4μN and 28.2μN, respectively. The smaller sheet has a shorter oscillation time while oscillating before it stabilizes. The damping ratio of the oscillation was between 0.1-0.2. The in-plane force and the stable time of pyrolytic graphite are related to its size ratio in comparison with the PM. This relationship is believed to promote stability, as the force acting on the graphite sheet will be distributed over a larger area when the sheet size increases. During the fixed-axis rotation process, the study found that the friction coefficient and friction force decreased as the rotational speed decreased. The diamagnetic levitation of pyrolytic diamagnetic levitation is also unable to maintain long-term axial rotation. Finally, friction force was tested using PG10 during fixed-axis rotation above a circular PM array. The results showed that the order of the friction coefficient is 10-3, and the friction force is about 0.8μN, decreasing with graphite rotation speed. We hope this technique will be used in crack detection, magnetic detection and other micromachine.

The COVID-19 pandemic over the past years has shown a great need for rapid, low-cost and on-site detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). In this paper, an aptamer-based colloidal gold nanoparticle lateral flow test strip was well developed to realize the visual detection of wild type SARS-CoV-2 spike protein (SP) and multiple variants. Under the optimal reaction conditions, a low detection limit of SARS-CoV-2 S protein of 0.68 nM was acquired, and the actual detection recovery was 83.3% to 108.8% for real world samples. This suggests a potential tool for the prompt detection of SARS-CoV-2 with good sensitivity and accuracy, and a new method for the development of alternative antibody test strips for the detection of other viral targets.

Blood testing is a crucial application in the field of clinical studies for disease diagnosis and screening, biomarkers discovery, organ function assessment, and personalized medication. Therefore, it is of utmost importance to collect precise data in a short time. In this study, we utilized Raman spectroscopy to analyze blood samples and extracted comprehensive biological information, including the primary components and compositions present in the blood. We conducted short-wavelength (532 nm green light) Raman scattering spectroscopy on blood samples, plasma, and serum, and subsequently analyzed the biological characteristics detected in each sample type. Our results indicated that whole blood had high hemoglobin content, which suggests that hemoglobin is a major component of blood. The characteristic Raman peaks of hemoglobin were observed at 690, 989, 1015, 1182, 1233, 1315, and 1562–1649 cm−1. Analysis of plasma and serum samples indicated the presence of β-carotene, which exhibited characteristic peaks at 1013, 1172, and 1526 cm−1. Additionally, in the field of medical blood testing, the novel 3D Silicon micro-channel device technology holds immense potential. It can serve as a substrate and helps to detect various diseases and biomarkers, providing real-time data to help medical professionals and patients better understand their health conditions. Changes in biological data collected in this manner could potentially be used to diagnose clinical diseases.

Underwater visual detection technology plays a pivotal role in fields such as marine exploration. With the increasing demand for underwater monitoring, the quest for efficient and reliable methods for underwater target recognition has become particularly significant. To address this requirement, this study developed an innovative underwater object detection architecture based on YOLOv8, named YOLOv8-MU, aimed at significantly enhancing detection accuracy.By integrating the LarK module proposed in UniRepLKNet to optimize the backbone network, YOLOv8-MU aims to achieve a larger receptive field without increasing the model’s depth. Further, this research introduces C2fSTR, an innovative method that combines Swin Transformer with the C2f module. Additionally, we have incorporated the SPPFCSPC_EMA module, which combines Cross-Stage Partial Fast Spatial Pyramid Pooling (SPPFCSPC) with attention mechanisms, significantly improving the detection accuracy and robustness of various biological targets. Moreover, by introducing a fusion block based on DAMO-YOLO into the neck of the model, we further enhanced the model’s capability in multi-scale feature extraction. Finally, the adoption of the MPDIoU loss function, designed around vertex distance, effectively tackles the challenges of localization accuracy and boundary clarity in underwater organism detection. Experimental results on the URPC2019 dataset demonstrate that the YOLOv8-MU model achieved an [email protected] of 78.4%, marking improvements of 5.6%, 1.1%, and 4.0% over YOLOv5s, YOLOv7, and YOLOv8n respectively, indicating the leading performance (SOTA) of this method. On the other hand, further evaluation on the URPC2020 dataset confirmed the generalization capability of the YOLOv8-MU architecture, with its [email protected] reaching 80.4%, surpassing various models including YOLOv5x and YOLOv8n, showcasing the wide applicability of our proposed improved model architecture.

Nanocrystalline silicon oxide (nc-SiOx:H) is a multipurpose material with its varied application in solar cells as a transparent front contact, intermediate reflector, back reflector layer and even tunnel layer for passivating contacts, owing to easy tailoring of its optical properties. In this work, we systematically investigate the influence of gas mixture (SiH4, CO2, PH3 and H2), RF power and process pressure on the optical, structural and passivation properties of thin n-type nc-SiOx:H films prepared in an industrial, high throughput, plasma-enhanced chemical vapor deposition (PECVD) reactor. We provide a detailed description of the n-type nc-SiOx:H material develop-ment using various characterization techniques (SEM, EDX, Raman spectroscopy, and spectro-scopic ellipsometry) with a focus on the relationship between the material properties and the pas-sivation they provide to n-type c-Si wafers characterized by their effective carrier lifetime (τeff). Further, we also outline the parameters to be kept in mind while developing different n-type nc-SiOx:H layers for different solar cell applications. We report a tunable optical gap (1.8 – 2.3 eV) for our n-type nc-SiOx:H films as well as excellent passivation properties with τeff up to 3.5 ms (iVoc ~ 715 mV) before annealing. Oxygen content plays an important role in determining the crystallinity and hence passivation quality of the deposited nanocrystalline silicon oxide films.

The efficiency of cold sheet and strip rolling of steels and non-ferrous metals in the main depends on the quality of the technological lubricant and its cost. In this regard, it is important to develop new compositions of effective metal-working coolants (MWC) having low cost and providing the maximum reduction in the friction coefficient. We developed and tested the new compositions of the MWC on basis of chicken fat, and mono- and diglycerides and their esters of boric acid synthesized from the wastes of sunflower oil production. The MWC were tested in DSEA on laboratory rolling mill 100x100 with a roll diameter of 260 mm during steel 08Kp rolling. The efficiency of the coolants was determined by the factor of metal stretch forming λ and the coefficient of friction μ in the deformation zone which was found by forward slip method. We found the metal-working coolant with 100 % concentration of boric acid esters of mono- and diglycerides is the most effective in steel rolling. Thus the new MWC on basis of boric acid esters of mono- and diglycerides synthesized from the wastes of sunflower oil production can be recommended for use in rolling of structural steels on account of availability, high efficiency, and a low cost.

Based on the need for real-time sag monitoring of Overhead Power Lines (OPL) for electricity transmission, this article presents the implementation of a hardware and software system for online monitoring of OPL cables and cable sag determination. The mathematical model based on differential equations and the methods of algorithmic calculation of OPL cable sag are presented. Considering that, based on the mathematical model presented, the calculation of OPL cable sag can be done in different ways depending on the sensors used, and the presented application uses a variety of sensors. Therefore, a direct calculation is made using one of the different methods. Subsequently, the verification relations are highlighted directly and, respectively, the calculation by the alternative method, which uses another group of sensors, to generate both a verification of the calculation and the functionality of the sensors, thus obtaining a defect observer of the sensors. The hardware architecture of the OPL cable online monitoring application is presented, together with the main characteristics of the sensors and communication equipment used. The configurations required to transmit data using the ModBUS and ZigBee protocols are also presented. The main software modules of the OPL cable condition monitoring application are described, which ensure the monitoring of the main parameters of the power line and the visualisation of the results both on the electricity provider's intranet using a web server and MySQL database, and on the Internet using an Internet of Things (IoT) server. This categorisation of the data visualisation mode is done in such a way as to ensure a high level of cyber security. Starting from the mathematical model of the OPL cable sag calculation, it goes through the stages of creating such a monitoring system, from the numerical simulations carried out using Matlab to the real-time implementation of this monitoring application. The main modules of the application software are: the software module for reading quantities from the sensor network through a ModBUS Input/Output (I/O) server, the software module for real-time calculation of the OPL cable sag, the software module for read/write operations based on MySQL type data, the software module for transferring data to the user's intranet through a web server, and the software module for viewing data by authorised users based on user and password through an IoT server. The development software environments used are Matlab and Laboratory Virtual Instrument Engineering Workbench (LabVIEW).

The ability to detect the presence as well as classify the activities of individuals behind visually obscuring structures is of significant benefit to police, security and emergency services in many situations. This paper presents the analysis from a series of experimental results generated using a through-the-wall (TTW) Frequency Modulated Continuous Wave (FMCW) C-Band radar system named Soprano. The objective of this analysis was to classify whether an individual was carrying an item in both hands or not using micro-Doppler information from a FMCW sensor. The radar was deployed at a standoff distance, of approximately 0.5 m, outside a residential building and used to detect multiple people walking within a room. Through the application of digital filtering, it was shown that significant suppression of the primary wall reflection is possible, significantly enhancing the target signal to clutter ratio. Singular Value Decomposition (SVD) signal processing techniques were then applied to the micro-Doppler signatures from different individuals. Features from the SVD information have been used to classify whether the person was carrying an item or walking free handed. Excellent performance of the classifier was achieved in this challenging scenario with accuracies up to 94%, suggesting that future through wall radar sensors may have the ability to reliably recognize many different types of activities in TTW scenarios using these techniques.

In this work, the analytical Lagrange-Kirchhoff model for the deformation for a taiko plate silicon is proposed. Under the conditions of validity of the linear theory of thin plates, the model is in agreement with the experimental data.

Ti and its alloys are the most commonly used materials for biomedical applications. However, bacterial infection after implant placement is still one of the significant rising complications. Therefore, the application of the antimicrobial agents into implant surfaces to prevent implant-associated infection has attracted lots of attention. Scientific papers have shown that inorganic antibacterial metal element (e.g. Ag, Cu, Zn) can be introduced to implant surfaces with the addition of metal nanoparticles or metallic compounds into electrolyte via micro-arc oxidation (MAO) technology. In this review, the effects of the composition and concentration of electrolyte and process parameters (e.g. voltage, current density, oxidation time) on morphological characteristics (e.g. surface morphology, bonding strength), antibacterial ability and biocompatibility of MAO antimicrobial coating were discussed in detail. Anti-infection and osseo-integration can be simultaneously accomplished with the selection of the proper antibacterial elements and operating parameters. Besides, MAO assisted by magnetron sputtering (MS) to endow Ti-based implant materials with superior antibacterial ability and biocompatibility was also discussed. Finally, the development trend of MAO technology in the future was forecasted.

Diversification in agroecosystems can increase the sustainability of agricultural production and reduce input dependence in agroecological transitions. This study evaluated the effects of intercropping and the introduction of flowering (aromatic) plant strips on the ratio of land use efficiency and crop damage for broccoli and lettuce association. Two experiments were conducted in 2022 and 2023 in experimental plots in southwestern Colombia. Crop association alone did not impact crop yield; the production was higher in the lettuce monoculture. However, in the presence of flowering plant strips, the land use equivalent ratio (LER) is >1 in the two years of study, with a high yield for broccoli. Regarding the damage by the silverback moth Plutella xilostella L on broccoli, no differences were found between crops established with or without flower strips. Similarly, flower strips did not affect the incidence of lettuce rot caused by Sclerotinia spp. In summary, our results support the idea that farmers can introduce flower strips into their horticultural fields to improve the eco-productive efficiency of their farms and reduce dependence on external polluting inputs. However, further research is needed to clarify the mechanisms underlying these results.

The Jiangmen Underground Neutrino Observatory (JUNO) is a 20 kton liquid scintillator multi-purpose underground detector, under construction near the chinese city of Jiangmen, with data taking expected to start in 2021. The main goal of the experiment is the neutrino mass hierarchy determination, with more than three sigma significance, and the high precision neutrino oscillation parameters measurements, detecting electron anti-neutrinos, emitted from two near-by (baseline of about 53 km) nuclear power plants. Besides, the unprecedented liquid scintillator type detector performance in target mass, energy resolution, energy calibration precision and low-energy threshold, features a rich physics program for the detection of low-energy astrophysical neutrinos, such as galactic core-collapse supernova neutrinos, solar neutrinos and geo-neutrinos.

Based on PVDF (piezoelectric sensing techniques), this paper attempts to study the propagation law of shock waves in brittle materials during the process of three-wavelength laser irradiation of polysilicon, and discusses the formation mechanism of thermal shock failure. The experimental results show that the vapor pressure effect and the plasma pressure effect in the process of pulsed laser irradiation lead to the splashing of high temperature and high density melt. With the decrease of the laser wavelength, the laser breakdown threshold decreases and the shock wave is weakened. Because of pressure effect of the laser shock, the brittle fracture zone is at the edge of the irradiated area. The surface tension gradient and surface shear wave caused by the surface wave are the result of coherent coupling between optical and thermodynamics. The average propagation velocity of laser shock wave in polysilicon is 8.47×103m/s, and the experiment has reached the conclusion that the laser shock wave pressure peak exponentially distributes attenuation in the polysilicon.

Microscopic vision plays an important role in automated micro-assembly. However, some uncertain factors in the assembly process, such as occlusion and stains can lead to the mistakes of feature extraction. Herein, to solve the problem, the deep learning techniques are introduced into the feature recognition tasks, focusing on the attention mechanism and visualizing CNNs for DL-based microscopic vision. The main contributions are summarized as follows: The CBAM attention mechanism is combined with the YOLOv5 algorithm to improve the accuracy and robustness of feature extraction. The micropart feature occlusion experiment results show that at 70% occlusion degree, YOLOV5-CBAM can reach 97.9% [email protected], which is 4.6% higher than the original one. Visualization analysis of DL-based model is conducted using Grad-CAM to make the decision result more transparent and avoid potential visual detection risks during assembly. The heatmap matching degree between GT area and high-light area is increased by 27.81% on average, which further verify the effectiveness of attention mechanism in micropart feature localization. Additionally, micropart surface stain and droplet quality classification models based on ResNet50 are trained to replace the manual sorting. The visual results are consistent with human eye discernment and judgement, confirming the reliability of parts and droplets sorting.

Objectives: Social distancing measures are currently implemented to control COVID-19 pandemic in many countries, including Saudi Arabia. The aim of this study was therefore to evaluate the awareness and adherence of the Saudi population to these measures. Methods: A web-based questionnaire was designed with 16 questions (8 questions related to demographics, 3 in relation to awareness about social distancing and 5 related to overall practice of social distancing). Results: 5105 participants completed the survey [58.4% female, 66.3% young individuals (aged 18-37 years), 55.8% bachelor degree holders, and 51.0% from the western region]. The Saudi Ministry of Health (MOH) was the main source of information about COVID-19 for most participants (78.2%). High awareness (81.3%) regarding social distancing was observed, associated mainly with female participants, those from the middle region and those with high education and income. Overall implementation of social distancing was satisfactory (score 3.13/5), with 37.8% never leaving home during the home-stay period. Better adherence to social distancing was observed for female participants, higher degree holders and those aged over 38 years. Conclusions: Organised plans by the Saudi MOH have been effective in raising awareness and improving practice of social distancing among public. However, the observed lower practice of social distancing by individuals with lower education and income indicates the need for targeted interventions to achieve better outcome.

The present paper deals with an improvement of the strengthening technique consisting in the combined use of straps—made of stainless steel ribbons—and CFRP strips, to increase the out-of-plane strength of masonry walls. The straps of both the previous and the new combined technique pass from one face to the opposite face of the masonry wall through some holes made along the thickness, giving rise to a three-dimensional net of loop-shaped straps, closed on themselves. The new technique replaces the stainless steel ribbons with steel wire ropes, which form closed loops around the masonry units and the CFRP strips as in the previous technique. A turnbuckle for each steel wire rope allows the closure of the loops and provides the desired pre-tension to the straps. The mechanical coupling—given by the frictional forces—between the straps and the CFRP strips placed on the two faces of the masonry wall gives rise to an I-beam behavior of the facing CFRP strips, which begin to resist the load as if they were the two flanges of the same I-beam. Even the previous combined technique exploits the ideal I-beam mechanism, but the greater stiffness of the steel wire ropes compared to the stiffness of the steel ribbons makes the constraint between the facing CFRP strips stiffer. This gives the reinforced structural element greater stiffness and delamination load. In particular, the experimental results show that the maximum load achievable with the second combined technique is much greater than the maximum load provided by the CFRP strips. Even the ultimate displacement turns out to be increased, allowing us to state that the second combined technique improves both strength and ductility. Since the CFRP strips of the combined technique run along the vertical direction of the wall, the ideal I-beam mechanism is particularly useful to counteract the hammering actions provided by the floors on the perimeter walls, during an earthquake. Lastly, after the building went out of service, the box-type behavior offered by the three-dimensional net of straps prevents the building from collapsing, acting as a device for safeguarding life.

Coconut is an important multipurpose crop wherein different stages of its maturity are used for different products. Traditional approach of its classification use sound formed by tapping the fruit, and the tapper will base its judgment through the sound he heard. The procedure was highly subjective and attempts had been made by other researchers to automate and classify the adulthood of the coconut objectively. Nowadays, deep learning techniques are being utilized to solve classification problems. One such method is Convolutional Neural Network (CNN) that takes raw pixel data, learns to extract features, and ultimately classifies the input. In this study, a portable device was developed that takes audio signals generated from tapping the fruit mechanically. This audio clip was converted to spectrogram and was used as input to a LeNet CNN architecture. We argue that CNN classifier has improved accuracy compared to the non-deep learning system. Our evaluation confirmed that the use of CNN had improved the accuracy of classifying coconut by about 15%.

A compact Mach-zehnder interferometer with a novel design of directional couplers and a phase shifter has been presented as a thermo-optical sensor. With the aim of reducing device size to micro and nano dimension silicon-on-insulator technology was employed. That allowed miniaturization of device size through the reduction of its cross sectional area to 0.066 µm² and the radius of curvature of both the arms of the directional coupler and S-bends of the phase shifter to 5 µm and C-bends to 3 µm. These nano size device dimensions made it possible to reduce the coupling gap to 0.2 µm, which resulted in a significant reduction in the coupling length. The device geometry and its performance characteristics were analyzed and optimized using coupled mode analysis and finite difference time domain simulation tools, respectively. The wavelength dependent transmission loss of the device was measured at different temperature to verify and validate its performance characteristics. Tested devices showed a remarkable temperature dependent transmission characteristic offering significant changes in transmission loss band – with as low as 0.45 ⁰C change in substrate temperature. The extinction ratio and the free spectral range of the device were 26 dB and 0.26 nm respectively in the wavelength range of 1549.5 nm – 1550.5 nm. These results imply that the devices presented here can be used as compact and highly sensitive thermal sensors and optical switches.

In this paper, we present an experimental procedure to enhance the dimensional accuracy of fabrication via Stereolithography (SLA) of features at the micro-scale. Using a custom benchmark part, deviations in feature dimensions (micro-pores diameters and depths) were detected and measured by confocal microscopy. Samples characterization and experimental observations allowed the identification of inaccuracy sources, mainly due to the laser beam scanning strategy and to the incomplete removal of uncured liquid resin in post-processing (i.e., IPA washing). As a technology baseline, the measured dimensional errors on pores diameters were up to -46%. A compensation method of the nominal laser spot diameter (85m) was defined and implemented resulting in relevant improvements in dimensional accuracy of 9.8% and 11.3% on full-open pores diameter and depth, respectively. Further investigation was performed on a customized test part to adjust the calibration procedure. The measurements revealed that the estimate of the laser beam spot size is 968m. Measurements on micro-pores having different sizes revealed that a constant compensation parameter (i.e., C=85, 96, 120m) is not fully effective at the micro-scale, where average errors still remain at -24%, -18.8%, and -16% for compensations equals to 85, 96 and 120m, respectively. A further experimental campaign allowed the identification of an effective nonlinear compensation law where the compensation parameter depends on the micro-feature size C= f (D). Results show a sharp improvement in dimensional accuracy on micro-pore fabrication, with errors consistently below +8.2%. The proposed compensation method can be extended for the fabrication of any micro-features without restrictions on the specific technology implementation. Concerning the inaccuracy introduced by the laser path, experimentation with a customized part allowed the optimization of the part orientation to reduce the errors and their differences along the X and Y machine axes.

GaN ultraviolet photodetector with metal-semiconductor-metal structure is achieved by growing on a periodic trapezoid column-shape patterned sapphire substrate using metalorganic chemical vapor deposition. Under 5-V reverse bias, the photodetector fabricated on such patterned sapphire substrate exhibits a lower dark current, a higher photocurrent, and a 476 % enhancement in the maximum responsivity as compare with those of the photodetector fabricated on conventional flat sapphire substrate. It is also found that the much larger UV-to-visible rejection ratio and the fact that responsivity drops in a smaller cut-off region are observed from photodetector fabricated by using a periodic trapezoid column-shape patterned sapphire substrate. These phenomena may all be attributed to the reduction of threading dislocation density and the improved quality of GaN film, as well as the internal reflection and/or scattering effect on the interface between GaN film and the periodic trapezoid column-shape pattern of the substrate.

In this article, we show theoretically and experimentally the formation of spin-waves band gaps in a magnonic crystal that was implemented by the deposition of periodic micro-structured strips of magnetite nanoparticles. A theoretical model describing the spectra of the transmitted spin-waves bandgaps is proposed. This is achieved using a simple model based on microwave transmission line theory and considering the presence of micro-structured strips of magnetite nanoparticles on the surface. Such magnonic crystal of equally spaced micro-structured strips of magnetite nanoparticles on the surface of an yttrium iron garnet thin film has been implemented and measured. The periodic micro-structured nanoparticles are deposited on the surface of such yttrium iron garnet single-crystal film grown on a gallium-gadolinium garnet substrate via dip-coating technique. Propagation of magnetostatic surface spin-waves is studied and it is shown that the presence of such periodic structure leads to the formation of spin-wave band gaps in the transmission characteristics. The spin-wave detection has been carried out using a pair of microwave antennas and a vector network analyzer. The results show that the periodic structure formed by the magnetite strips modifies the spectra of the transmitted spin waves producing band gaps.

Photon-counting Computed Tomography (PCCT) is a promising cardiovascular-imaging technique. Using detectors that count the number and energy of photons in multiple bins, PCCT offers several advantages over conventional CT, including a higher image quality, reduced contrast agent volume, radiation doses, and artifacts. Although PCCT is well established for cardiac imaging in assessing coronary artery disease, its application in vascular imaging remains limited. This review summarizes the available literature and provides an overview of the current use of PCCT for the diagnosis of vascular conditions. Of the 13 records selected in the initial search, 7 articles were included in the present review: 6 cohort studies and 1 case report. This review synthesized the available literature on PCCT in vascular imaging, focusing mainly on endoleaks detection and characterization after endovascular aneurysm repair (EVAR), contrast dose volume, and radiation exposure reduction, particularly in patients with chronic kidney disease and in those requiring follow-up CT.

The main purpose of this work was to tests of form and size of fatigue wear of the top layer of oil gear pump wheel (3PW-BPF-24). The object of tests was operated during a determined number of hours at strictly controlled operational and environmental parameters. A microscope of focal differentiation by Alicona InfiniteFocus G4 (with Focus-Variation optical measuring technology) was used for an identification, measurement and description of noticed superficial defects, which resulted from the fatigue process of the top layer and an earlier thermochemical treatment. The work was finished with an analysis of obtained results (based on the analysis of 3D scans) and conclusions concerning about optimization of the thermal treatment. Taking into consideration the presented results (suggestions) in the technology of improving strength properties of gear wheels (of this type oil pumps) may render it possible to obtain an appropriate fatigue endurance of the top layer, i.e. a minimization of observed superficial defects.

Integrated ultra-low-loss waveguides are highly desired for integrated photonics to enable applications that require long delay lines, high-Q resonators, narrow filters, etc. Here we present an ultra-low-loss silicon waveguide on 500 nm thick SOI platform. Meter-scale delay lines, million-Q resonators and tens of picometer bandwidth grating filters are experimentally demonstrated. We design a low-loss low-reflection taper to seamlessly integrate the ultra-low-loss waveguide with standard heterogeneous Si/III-V integrated photonics platform to allow realization of high-performance photonic devices such as ultra-low-noise lasers and optical gyroscopes.

: This work introduces the instrument design of the medium energy proton detector (MEPD, detection range: 30keV-5MeV) mounted on the Chinese Fengyun-4B (FY-4B) satellite. Compared with the similar detector on the Fengyun-3E (FY-3E) satellite, the instrument has undergone significant changes due to the different orbital radiation environment and solar lighting conditions. Based on the calculation of radiation model AP8, the geometry factor is reduced to 0.002 cm2sr, while the MEPD on FY-3E satellite is 0.005 cm2sr. Another difference is that sensors in some directions is exposed to direct sunlight for 80 minutes every day on this orbit, depending on the attitude angle of the satellite, which is much worse than that on FY-3E satellite. According to the calculation results of permeability of photons through different materials, a 100 nm thickness nickel film is added in front of sensors in order to eliminate light pollution completely. The experiment on the solar simulator shows that the measure is effective and the detector has no error counts when the solar irradiance coefficient is 1.0. In addition, Geant4 software is applied to simulate particle transportation process under complete machine condition so that to check the contamination of electrons on sensors among all directions after magnetic deflection. Data obtained in orbit shows that the instrument works properly, and the data is in good agreement with the AP8 model. The observations of the MEPD on board the FY-4B satellite can provide important support for the safety of the spacecraft and the theoretical research related to space weather.

We demonstrate the use of a nanotechnology-based approach for the investigation of enzymatic activity of a single molecule of horseradish peroxidase with a solid-state nanopore. The artificial 5 nm solid-state nanopore has been formed in a 40-nm-thick silicon nitride structure. Single molecule of HRP has been entrapped into the nanopore. The activity of horseradish peroxidase (HRP) enzyme molecule inserted in the nanopore has been monitored by recording the time dependence of the ion current through the nanopore in the course of the reaction of 2,2′-azino-bis(3-ethylbenzothiazoline-6-sulfonate) (ABTS) oxidation reaction. We have found that in the process of ABTS oxidation in the presence of 2.5 mM hydrogen peroxide, individual HRP enzyme molecules are able to retain activity for approximately 700 seconds before a decrease in the ion current through the nanopore, which can be explained by structural changes of the enzyme.

Smart sensors based on graphene field effect transistor and biologically receptors are regarded as a promising nanomaterial that could be the basis for future generations of selective real-time monitoring of target analytes and smaller electronics. So the purpose of this paper is to provide details a real-time and selective explosive sensor based on GFETs and PDA-based lipid membranes coupled with biologically inspired TNT peptide receptors. Following an introduction, this paper describes the way of fabrication of the GFETs device by investigation methods for transferring graphene sheet from Cu substrates to target substrates, which is functionalized by the TNT peptide receptors, in order to offer a system which has the capability of answering the presence of related target molecules. Field effet transistor was fabricated using graphene as a channel and monitored by the source-drain current and back-gate voltage curves in the measurement. The transport property changed compared to that of the FET made by intrinsic graphene, that is, the Dirac point position moved from positive Vg to negative Vg, indicating the transition of graphene from p-type to n-type after annealing in TNT, and GFET sensor show good sensitivity and selectivity response.

The objective of the study was to analyse the antimicrobial susceptibility trends of Spanish porcine bacteria to quinolones, cephalosporins and polymyxins. Isolates of Actinobacillus pleuropneumoniae, Pasteurella multocida, and Escherichia coli were isolated from sick pigs from 2019 to 2022. Antimicrobial susceptibility test was determined by minimal inhibitory concentration (MIC) following internationally accepted methodology. MIC categorization was based on distributing the range of MIC values in four categories being category one the most susceptible (lowest MIC value) and four the less susceptible one (highest MIC value). Moreover, clinical susceptibility (susceptible/resistant) was also determined according to CLSI and EUCAST clinical breakpoints. A logistic and multinomial logistic regression model was used to analyze the susceptibility data for dichotomized and categorized MIC data, respectively for any pair of antimicrobial/microorganism. In general terms, the antimicrobial susceptibility of pig bacteria to these antimicrobials remained stable or increased in the last four years in Spain. In the case of A. pleuropneumoniae and quinolones, it was observed a significant temporal trend where isolates from 2020 had significantly increased odds of being more susceptible than isolates from 2019. In the case of E. coli and polymyxins, a significant temporal trend was observed where isolates from 2020 and 2021 had significantly increased odds of being more susceptible than isolates from 2019 and 2020, respectively. Finally, a significant odd of being less susceptible was only observed for cephalosporins and E. coli for 2020 versus 2019, stagnating for the rest of study period. These results provide sound data on critical important antimicrobials in swine medicine.

This study reports on the development of bio-based hydrophobic coatings for packaging papers through deposition of polyhydroxybutyrate (PHB) particles in combination with nanofibrillated cellulose (NFC) and plant wax. In a first approach, PHB particles in micrometer range (PHB-MP) were prepared through a phase-separation technique providing internally nanosized structures. The particles were transferred as a coating by dip-coating filter papers in the particle suspension, followed by sizing with a carnauba wax solution. This approach allowed partial to almost full surface coverage of PHB-MP over the paper surface resulting in static water contact angles of 105° to 122° and 129° to 144° after additional wax coating. In a second approach, PHB particles with submicron sizes (PHB-SP) were synthesized by an oil-in-emulsion (o/w) solvent evaporation method, and mixed in aqueous suspensions with 0 to 7 wt% NFC. After dip-coating filter papers in PHB-SP/NFC suspensions and sizing with a carnauba wax solution, static water contact angles of 112° to 152° were obtained. The intrinsic properties of the particles were analyzed by scanning electron microscopy, thermal analysis and infrared spectroscopy, indicating higher crystallinity for PHB-SP than PHB-MP. The chemical interactions between the more amorphous PHB-MP particles and paper fibers were identified as an esterification reaction, while the morphology of the NFC fibrillar network was playing a key role as binding agent in the retention of more crystalline PHB-SP at the paper surface, hence contributing to higher hydrophobicity.

Using pumps operating as turbines (PATs) offers the possibility of increasing the sustainability of water and energy systems by recovering the excess of energy that would be otherwise lost in pressure reducing valves or head loss chambers. In on-grid applications, there are many research works and implementations of PATs. However, there is still limited research for the optimization of efficiency and stability of PATs operating in off-grid systems. This work contributes to the development of stable direct current (DC) off-grid electric systems based on PATs, by optimizing and analysing the energy efficiency and stability for a wide range of operation. A self-excited induction generator (SEIG) coupled to the PAT is provided to cover the conventional type of electric ma-chines typically coupled to the hydraulic pumps. In this context, a methodology is proposed, based on the hydraulic, mechanical and electric subsystems, to define the PAT-SEIG operational area, to maximize energy conversion and the system efficiency. This will guarantee stable electric output quantities when operating in a DC off-grid system. In addition, an analytical model is proposed to estimate the PAT-SEIG operation under specific conditions. With this, water managers are suitable to design and optimize an off-grid PAT-SEIG system and to define the best hydraulic machines, electronic equipment, and all different control elements to maximize energy conversion within the target of operational limits. To develop and verify this new methodology, two micro PAT-SEIG setups were implemented in the hydraulic laboratory of IST/CERIS under typical operating conditions. The proposed solution proved to be resilient under a variable load regime. The system's maximum efficiency can be adapted using different capacitor values for the excitation of the SEIG, and the operational range is limited to the electric components. Considering the nominal efficiencies of the system’s components, the maximum p.u. efficiency obtained for each PAT-SEIG system were between 0.7 and 0.8 p.u.

This paper presents an improved indoor localization system based on RF and ultrasonic signal which we named SNSH system. This system composes of a transmitter mounted in a mobile target, and a series of receiver nodes which are managed by a coordinator. By measuring Time Delay of Arrival (TDoA) of RF and ultrasonic signal from the transmitter, distance from target to receiver node is calculated and sent to the coordinator through CAN network, and all the information are gathered in PC to estimate 3D position of the target. Sine wave detector and dynamic threshold filter are applied to provide excellent accuracy of range measurement from TDoA result, and multilateration algorithms is realized to optimize coordinate determination accuracy. Specifically, Linear Least Square and Non-linear Least Square techniques are implemented to contrast their performances in target coordinate estimation. RF signal encoding/decoding time, time delay in CAN network and math calculating are carefully considered to ensure optimal system performance and get ready for field application. Experiments show that sine wave detector algorithm has greatly improved range measurement accuracy, with mean error at 2.2mm and maximum error at 6.7 mm, for distance below 5m. In addition, 3D position accuracy is greatly enhanced by multilateration methods, with mean error in position stay under 15mm, and 90% confident error values at 23mm for LLS, 20mm for NLS. Overall system update period has been verified in real system operation, with maximum rate at 25ms, and compared with other existing researches.

This review explores the potential implementation of lithium tetraborate (Li2B4O7) as a scintillator medium for neutron detection applications. Several characteristics required for the neutron detection process suggest that Li2B4O7 could be a suitable material for scintillation-based neutron detection systems. The inherently large neutron capture cross-section due to 10B and 6Li isotopes, and the ease with which Li2B4O7 can be enriched with these isotopes, combined with the facile inclusion of rare-earth dopants are all expected to improve luminescent properties as well as neutron detection efficiency of Li2B4O7. The electronic structure of doped and undoped Li2B4O7 are explored using photoemission and inverse photoemission spectroscopies, optical measurements, and theoretical computational studies such as density functional theory. The scintillation properties are further enhanced because of the wide bandgap, and transparency towards the photons that are emitted following neutron capture.

: Microplastics and nanoplastics (MNPs) are becoming an increasingly severe global problem due to their widespread distribution and complex impact on living organisms. Apart from their environmental impact, the effects of MNPs on living organisms have also continued to attract attention. The harmful impact of MNPs has been extensively documented in marine invertebrates and larger marine vertebrates like fish. However, the research on the toxicity of these particles on mammals is still limited, and their possible effects on humans are poorly understood. Considering that MNPs are commonly found in food or food packaging, humans are primarily exposed to them through ingestion. It would be valuable to investigate the potential harmful effects of these particles on gut health. This review focuses on recent research exploring the toxicological impacts of micro- and nanoplastics on the gut, as observed in human cell lines and mammalian models. Available data from various studies indicate that the accumulation of MNPs in mammalian models and human cells may result in adverse consequences, in terms of epithelial toxicity, immune toxicity, and disruption of gut microbiota. The paper also discusses the current research limitations and prospects in this field, aiming to provide a scientific basis and reference for further studies on the toxic mechanisms of micro- and nanoplastics.

As is well known, the main contribution of the FRP strips to the strength of load-bearing walls is an improvement in the in-plane strength. This paper deals with the possibility of applying the FRP strips in way to modify the strengthening mechanism of the FRP reinforcing system, from an in-plane to an out-of-plane strengthening mechanism. In order to achieve this goal, a second reinforcement system – derived from the CAM system (Active Confinement of Masonry) – provides connections between the FRP strips placed on the opposite sides of the wall. This new strengthening technique – called the straps/strips technique – establishes a stiffness constraint that forces the opposing FRP strips to behave like two flanges of an FRP I-beam embedded in the wall. Consequently, the use of FRP strips also improves the flexural strength of the wall. The present paper briefly summarizes the results obtained in previous works with the straps/strips technique and proposes an improvement of this strengthening technique, based on some weak-points emerged in the early experimentations. The paper also shows the results of a further experimental test, performed with the improved straps/strips technique. Finally, the similarity between FRP strips with transversal connection and concrete wythes of a sandwich panel with flexible connectors leads to interpret the behavior of the ideal I-beam in terms of composite action established between the FRP strips. This paves the way for analytical modeling of the straps/strips technique.

Space-based gravitational wave detection is extremely sensitive to disturbances. The Keplerian configuration cannot accurately reflect the variations in spacecraft configuration. Planetary gravitational disturbances are one of the main sources. Numerical simulation is an effective method to investigate the impact of perturbation on spacecraft orbits. This study shows that, in the context of the Taiji project, Earth’s gravity is an essential factor in the change in heliocentric formation configuration, contributing to the relative acceleration between spacecrafts in the order of O(10−6)m·s−2. Considering 00:00:00 on October 27, 2032 as the initial orbiting moment, under the influence of Earth’s gravitational perturbation, the maximum relative change in armlengths and variation rates of armlengths for Taiji is 1.6×105km, 32m·s−1 respectively, compared with the unperturbed Keplerian orbit. Additionally, by considering the gravitational perturbations of Venus and Jupiter, the armlength and relative velocity for Taiji are reduced by 16.01% and 17.45%, respectively, compared with when only considering that of Earth. The maximum amplitude of the formation motion indicator changes with the orbit entry time. Results show that the relative velocity increase between the spacecrafts is minimal when the initial orbital moment occurs in July. Moreover, the numerical simulation results are inconsistent when using different ephemerises. The differences between ephemeris DE440 and DE430 are smaller than those between DE440 and DE421.

In the framework of maritime surveillance, vessel detection techniques based on spaceborne Synthetic Aperture Radar (SAR) images have promoted extensive applications for the effective understanding of unlawful activities at sea. The paper deal with this topic presenting a novel approach exploiting a cascade application of a pre-screening, and discrimination phase. The latter leverage the SAR spectrum by means of sub-looks analysis. For the first time, the method has been validated with experiments on multi-frequency (C-, X-, and L-band) SAR images. For a future syngergic exploitation of more SAR missions, the developed dataset, composed of Sentinel-1, SAOCOM and COSMO-SkyMed images, is comprehensive of multiple images gathered over the same area with short time lag (below 15 minutes). Finally, the diversified processing chains and the results for each mission product and scenarios are discussed. Being the first dataset of SLC (Single Look Complex) SAR multi-frequency data, the present work intends to encourage additional research in this promising field of research.

Loop detectors are probably the widest-used technology for traffic state estimation. Previous research has shown that loop detector positions within the link significantly affect the estimation of the macroscopic fundamental diagram (MFD) of a given network. This paper examines the biases produced by the positioning of loop detectors on the MFD, using both analytical and simulation methods, as well as empirical data from UTD-19. We confirm earlier results that a uniform distribution of loop detector positions reduces the bias. For non-uniform distribution, we found that: (i) the subsets of the MFD by the loop detector position help estimate whether the loop detector MFD will have a bias; (ii) if the detectors in the network are positioned more downstream with a larger variation, the loop detector MFD is more likely to have a discrepancy in position subsets of the MFD; (iii) a lower ratio of link length to green signal time elevates the MFD bias as well. This research opens the possibility for the bias of MFD induced by the loop detector data to be corrected by only using itself.

The vast rise in the number of Internet-connected devices necessitates a more accessible spectrum. As a result, Cognitive Radio was already proposed as a solution to the problem of restricted spectrum resources by utilizing available spectrum which is assigned to primary users. This method allows the secondary user to utilize the spectrum whenever the primary user is not using it, and it does so without intruding with the primary user. Whenever the secondary user detects the spectrum, it faced some issues, such as complexity in sensing leading to a lack of noise value, and the primary user is hidden to all secondary users. In order to tackle these challenges, an adaptive threshold matched filter detector and a cooperative matched filter detector are utilized in this paper to detect the spectrum. The probability of detection (Pd), probability of miss detection (Pm), and probability of false alarm (Pf) are the metrics used to assess sensing accuracy. To simulate suggested detectors, the MATLAB R2020a software was utilized. In comparison to earlier studies, the simulation conclusions reveal that the detection process starts with lower SNR values.

Fluorescence microscopy provides an unparalleled tool for imaging biological samples. However, producing high-quality volumetric images quickly and without excessive complexity remains a challenge. Here, we demonstrate a simple multi-camera structured illumination microscope (SIM) capable of simultaneously imaging multiple focal planes, allowing for the capture of 3D fluorescent images without any axial movement of the sample. This simple setup allows for the acquisition of many different 3D imaging modes, including 3D time lapses, high-axial-resolution 3D images, and large 3D mosaics.

Micro-combs [1-4] - optical frequency combs generated by integrated micro-cavity resonators – offer the full potential of their bulk counterparts [5,6], but in an integrated footprint. The discovery of temporal soliton states (DKS – dissipative Kerr solitons) [4,7-11] as a means of mode-locking micro-combs has enabled breakthroughs in many fields including spectroscopy [12,13], microwave photonics [14], frequency synthesis [15], optical ranging [16,17], quantum sources [18,19], metrology [20,21] and more. One of their most promising applications has been optical fibre communications where they have enabled massively parallel ultrahigh capacity multiplexed data transmission [22,23]. Here, by using a new and powerful class of micro-comb called “soliton crystals” [11], we achieve unprecedented data transmission over standard optical fibre using a single integrated chip source. We demonstrate a line rate of 44.2 Terabits per second (Tb/s) using the telecommunications C-band at 1550nm with a spectral efficiency – a critically important performance metric - of 10.4 bits/s/Hz. Soliton crystals exhibit robust and stable generation and operation as well as a high intrinsic efficiency that, together with a low soliton micro-comb spacing of 48.9 GHz enable the use of a very high coherent data modulation format of 64 QAM (quadrature amplitude modulated). We demonstrate error free transmission over 75 km of standard optical fibre in the laboratory as well as in a field trial over an installed metropolitan optical fibre network. These experiments were greatly aided by the ability of the soliton crystals to operate without stabilization or feedback control. This work demonstrates the capability of optical soliton crystal micro-combs to perform in demanding and practical optical communications networks.

Due to their wide range of uses in modern technology, nanomaterial’s of silver metallic (Ag-NPs) have engaged considerable concern, driving significant research with development efforts. This study focuses on investigating the antimicrobial properties of Ag-NPs, encompassing their production, characterization, and biological aspects. The eco-friendly extracellular biosynthetic method employed in this work utilized extracts from the marine fungus Aspergillus flavus MK4 as reducing agents for nanoparticle synthesis. Analyzing the colloidal Ag-NPs using UV-visible spectroscopy revealed a peak in absorbance at 460 nm, indicating the presence of plasmonic properties. The electrons imaging of internal structure (TEM) elucidated spherical shape of the Ag-NPs by 15 nm size. Testing against bacterial diversities (Gr-ve & Gr+ve) revealed potent antibacterial and antifungal efficacy. Cytotoxicity versus HepG-2 cell line was assessed using the MTT assay, and antioxidant properties were examined through the radical scavenging (DPPH) assay. In wise of their conceivable applications in the fields of antibacterial, anticancer, and wound-healing, the Ag-NPs that were synthesized exhibit promising features. With its powerful ability to synthesize silver nanoparticles (Ag-NP), Aspergillus flavus MK4 Aspergillus flavus MK4 can generate nanoparticles extensively characterized, demonstrating their antibacterial, antioxidant, anticancer, and wound-healing properties.

This computational research study will compare the specific charge capacity (SCC) between lithium ions inserted into crystallize silicon (c-Si) nanowires versus sodium ions inserted into amorphous silicon (a-Si) nanowires. It will be demonstrated that the potential energy V(r) within the lithium-silicon nanowire supports a coherent energy state model with discrete electron particles while the sodium-silicon nanowire potential energy will be discovered to be essentially zero and thus the electron current that travels through the sodiated silicon nanowire will be modeled as free electron with wave-like characteristics. This is due to the vast differences in the electric fields of the lithiated and sodiated silicon nanowires where the electric fields are of the order of 1e10 V/m and 1e-15 V/m respectively. The main reason for the great disparity in electric fields are due to the present of optical amplification within lithium ions and the absence of this process within sodium ions. It will be shown that optical amplification develops coherent optical interactions which is the primary reason for the surge of specific charge capacity in the lithiated silicon nanowire. Conversely, the lack of optical amplification is the reason for the incoherent optical interactions within sodium ions which is the reason for the low presence of SCC in sodiated silicon nanowires.

We present the results on photothermal (PT) and heat conductive properties of nanogranular silicon (Si) films synthesized by evaporation of colloidal droplets (drop-casting) of 100 ± 50 nm sized crystalline Si nanoparticles (NP) deposited on glass substrates. Finite difference time domain (FDTD) and finite element mesh (FEM) modeling of absorbed light intensity and photo-induced spatial temperature distribution across the Si NP films were well correlated with the local temperatures measured by micro-Raman spectroscopy and used for determination of heat conductivities in the films of various thicknesses. Cubic-to-hexagonal phase transition in these films caused by laser heating was found to be heavily influenced by the film thickness and heat conductive properties of glass substrate, on which the films were deposited. Heat conductivities across the drop-casted Si nanogranular films were found to be in the range of lowest heat conductivities of other types of nanostructurely voided Si films due to enhanced phonon scattering across inherently voided topology, weak NP-NP and NP-substrate interface bonding within nanogranular Si films.

The effects of soluble silicon fertilization on monocots and dicots have been widely studied. However, little is known regarding its effects on protecting epiphytes against insect and fungal pests. The efficacy of silicon fertilizer to reduce damage by thrip pest complexes, namely: Thrips palmi Karny, Frankliniella occidentalis Pergande, Chaetanaphothrips orchidii Moulton, and Chaetanaphothrips signipennis Bagnall (Thysanoptera: Thripidae), and fungal pathogens: Botrytis cinerea Persoon (Helotiales: Sclerotiniaceae) and Fusarium spp. Link (Hypocreales: Nectriaceae) was examined during a nine-month greenhouse trial in Hawaii. The trial assessed yield, quality, and pest damage across three common varieties of dendrobiums. All replicates received additional soluble silicon fertilizer applications alternating weekly between soil drench and foliar (50 mg Si/plant) applications. Yield, quality, and spray length, pest damage, plant vigor, SPAD, and leaf temperature were measured. Data were analyzed using a generalized linear model (glm) with repeated measures followed by post-hoc pair-wise comparisons in R, version 4.3.1. Treatment effects were significant at P

Abstract: Development of the fast neutron radiography with higher penetration capability in Non-Destructive Testing (NDT) techniques is rapidly. The detection efficiency and the imaging spatial resolution are the main problem of the radiography detector for many fast neutron imaging systems. In this paper, a detector composed of pixelated EJ200 scintillator array，an 16 × 16 silicon-photomultipliers (SiPM) array, and a capacitive multiplexing network readout electronics is designed. Using Monte-Carlo simulations，the main parameters of the detector was optimization. Then the detector prototype was fabricated and tested at a 14 MeV D-T neutron source. The preliminary test results showed that the prototype has spatial resolution of 1.26 mm. Using pixelated scintillator structure，the conflict between spatial resolution and detect efficiency could improved. Moreover, SiPMs offer a flexibility for the expansion of application field of the imaging system due to their excellent photon detection performance, relatively low price and joint possibility for large area.

Compton cameras detect scattered gamma rays and estimate the distribution of gamma-ray sources. Nonetheless, crafting a camera tailored to a specific application presents formidable challenges, often necessitating the implementation of diverse image reconstruction techniques. Delving into the factors influencing these cameras can pave the way for design optimization and performance enhancement. This study introduces an inventive detector design for Compton imaging systems, building upon the achievements of prior designs. The proposed system contains eight scatterer detectors and a semiconductor absorber detector, spaced at 1 mm and 30 mm intervals, respectively. The source-to-first-scatterer-detector distance is 5 mm, with scatterer and absorber detector plates measuring 70× 70× 2.125 mm³ and 70× 70× 10 mm³, respectively. Geant4 simulation toolkit models the Compton imaging system, and an analytical method reconstructs Compton camera images. Unlike more straightforward techniques, the analytical method directly reconstructs Compton camera images by solving the equation relating to the reflected image data. This approach is implemented in the C++ programming language. The study's findings reveal that the analytical method discerns optimal conditions and parameters that significantly influence efficiency, yielding a full width at half maximum (FWHM) of 3.7 mm with an angular uncertainty of approximately 2.7 degrees at an energy level of 0.662 MeV. Compared to another experimental design employing the analytical image reconstruction approach, the FWHM value decreased by 0.7 mm. This study presents an innovative detector design and an analytical reconstruction method for Compton imaging systems, showcasing improved efficiency and accuracy.

Microorganisms drive the biogeochemical cycles that link abiotic and biotic processes in the aqueous environment and are intricately associated with plastic debris. The detection of microplastics in water and sediment introduces new concerns as small particle size allows for yet unconsidered pathways for plastics in the food web and element cycles. In this review, we present current knowledge of microbe-plastic interactions and summarize the potential impact of biogeochemical processes on plastic distribution, cycling, transport, and sedimentation. We explore how microbe-plastic interactions influence the exposure of consumers to plastics and plastic degradation products. Key methods used to elucidate biofilm development, microbial biodegradation, and plastic detection in the aqueous environment are discussed. Finally, we comment on potential future questions and research directions needed to further define the role of microorganisms in the environmental fate of microplastics.

We report a novel dual-band barrier infrared detector (DBIRD) design using type-II superlattices (T2SLs). The DBIRD structure consists of back-to-back barrier diodes: a "blue channel" (BC) diode which has an nBp architecture, an n-type layer of larger bandgap for absorbing blue band infrared/barrier/p-type layer, and a "red channel" (RC) diode which has an pBn architecture, a p-type layer of smaller bandgap for absorbing red band infrared/barrier/n-type layer. Each has a unipolar barrier using a T2SL lattice matched to a GaSb substrate to impede the flow of majority carriers from the absorbing layer. Each channel in the DBIRD can be independently accessed with a low bias voltage, as is preferable for high-speed thermal imaging. Device modeling of DBIRDs and simulation results of the current-voltage characteristics under dark and illuminated conditions are also presented. They predict that dual-band operation of the DBIRD will produce low dark currents and 27-33% quantum efficiencies for the in-band photons in the BC with λc=5.58 μm, and a nearly-constant 33% in the RC with λc=8.05 μm. The spectral quantum efficiency of the BC for 500 K blackbody radiation is approximately 20% over the range of λ=3 − 4.2 μm, while that of the RC has a peak of 42% at 5.7 μm. The DBIRD may provide improved high-speed dual-band imaging in comparison with NBn dual-band detectors.

Muography is an expanding technique for the investigation of the internal structure of targets of interest in geophysics. The flux of high penetrating muons produced by primary cosmic rays is attenuated by traversing kilometer size objects like X-ray flux is attenuated through the human body. This gives the possibility to study the internal structure of volcanoes or underground cavities, e.g., starting from the measure of the muon flux transmission through the target. Many groups of researchers working with this technique have to face with high background level that afflicts the reconstruction of muon tracks near the horizontal direction. An important source of background is the scattering of particles near the detector that produces a wrong reconstruction of the incoming direction. An innovative technique based on Cherenkov radiation was investigated by means of Monte Carlo simulations developed in Geant4 toolkit and MATLAB. The results reported in this paper show that the presented technique is able to correctly distinguish the incoming direction of particles with an efficiency higher than 98%. This new kind of detector could represent an alternative for high resolution charged particle tracking also for other applications.

In this work the close relation between vorticity and micro-rotation in micropolar flows in Rn (n = 2 or 3) is identified and used to explain the faster decay by t^(-1/2) of the angular velocity of the micro-rotation of fluid particles, as well as establishing its optimality. For this purpose important upper and lower bounds for Leray solutions in homogeneous Sobolev spaces are derived, using the monotonicity approach recently introduced by the authors for dissipative systems in general. Several related results of interest are also given along the discussion.

In the paper the experimental methodology for the single-crystal circular plate deformation measurement and subsequent procedure for mechanical properties quantitation are developed. The procedure is based on a new numerical-analytical solution of nonlinear boundary-value problem for finite deformations of a circular anisotropic plate. Using the developed method, a study of the deformation of single-crystal circular plates formed on the basis of a silicon-on-insulator structure was carried out. The values of residual stresses are determined and it is shown that the presence of these stresses increases the flexural rigidity of the plate in several times.

Silicon nanoparticles (SiNPs) are highly promising for biological and biomedical applications, including bioimaging, due to their unique opltical properties (i.e. strong fluorescence and very high photostability). Their low or negligible in vitro toxicity has been reported, but in vivo toxicity and biological effects of SiNPs are still uncertain. Uncoated SiNPs were dispersed in distilled water via sonication, and their rapid aggregation was observed (319.0 ± 2.4 nm particle size). In vivo toxicity was studied using Danio rerio embryos and larvae. Rapid aggregation in their incubation medium was observed; besides that, SiNPs at 25 mg/L or higher concentration induced swim bladder malformation and/or death of the fish. The estimated LC50 value for 7-day larvae was 180 mg/L. This is the first in vivo toxicity study of uncoated and unfunctionalized SiNPs. To achieve better stability in biological media and lower toxicity, SiNPs should be covered with hydrophilic layers, but their absorption by cellular membranes may be weaker in this case.

Anomaly occurrences in hydraulic machinery may lead to massive systems shut down, jeopardizing the safety of the machinery and its surrounding human operator(s) and environment, and the severe economic implications succeeding the faults and their associated damage. Hydraulics are mostly placed in ruthless environments, where they are consistently vulnerable to many faults. Hence, not only the machines and their components are prone to anomalies, but also the sensors attached to them, which monitor and report their health and behavioral changes. In this work, a comprehensive applicational analysis of anomalies in hydraulic systems extracted from a hydraulic test rig is thoroughly achieved. Firstly, we provided a combination of a new architecture of LSTM autoencoders and supervised machine and deep learning methodologies to perform two separate stages of fault detection and diagnosis. The two phases are condensed by: the detection phase using the LSTM autoencoder. Followed by the fault diagnosis phase represented by the classification schema. The previously mentioned framework is applied to both component and sensor faults in hydraulic systems, deployed in the form of two in-depth applicational experiments. Moreover, a thorough literature review of the past decade related work for the two stages separately is successfully conducted in this paper.

Any Geiger counter can be used as an effective cosmic ray detector on its own. In fact, it is known that even in the absence of a radioactive source, the instrument detects what is known as background radiation, which consists of various types of ionizing particles present in the environment. Remarkably, it is estimated that up to 15% of this background radiation is attributable to cosmic rays, high-energy particles originating from outer space. The remaining radiation detected by the Geiger counter originates from terrestrial sources, such as natural radioactivity in the ground and in the air. The main goal of this project is to build a muon detector for scientific and educational purposes using two commercial DIY Geiger counter kits and just a few additional components. To identify cosmic radiation from terrestrial radiation and improve the accuracy of cosmic ray measurements, the use of a coincident circuit is essential. This coincident circuit was introduced in cosmic ray physics by Walther Bothe and Bruno Rossi in the early 1930s and allows for the detection of a subatomic particle passing through two or more sensors, thereby reducing false positives and enhancing the reliability of cosmic ray detection.The following idea is an alternative to our AMD5 detectors, instruments that we have been using for years to teach and perform scientific experiments in the cosmic ray field under the umbrella of the ADA project (2023 Particles, Arcani et al.). The resulting device offers a reliable and cheap solution for the same goal, making it a valuable tool for both educational purposes and even scientific surveys.

Semiconductors play a very important role in modern society. The improvement in performance of semiconductors is what has enabled the world to grow at such a fast pace. For decades scaling has been done through Moore’s law i.e performance improvements have been obtained due to transistor scaling where the number of transistors per unit area increase is what has contributed to the increase in performance. However, with transistor scaling reaching its limitations we need to find alternate methods to enhance silicon design to suit the computational need of modern society. To address this problem we will be looking into a few methods that enable performance scaling with a focus on analysing the most popular implementation of each in the industry.

Light trapping in single nanowires (NWs) are of vital importance for photovoltaic applications. However, circular NWs (CNWs) can limit its light-trapping ability due to high geometrical symmetry. In this work, we present a detailed study of light trapping in single NWs with an elliptical cross-section (ENWs). We demonstrate that the ENWs exhibit significantly enhanced light trapping compared with the CNWs, which can be ascribed to the symmetry-broken structure that can orthogonalize the direction of light illumination and the leaky mode resonances (LMRs). That is, the elliptical cross-section can simultaneously increase the light path length by increasing the vertical axis and reshape the LMR modes by decreasing the horizontal axis. We found that the light absorption can be engineered via tuning the horizontal and vertical axes, the photocurrent is significantly enhanced by 374.0% (150.3%, 74.1%) or 146.1% (61.0%, 35.3%) in comparison with that of the CNWs with the same diameter as the horizontal axis of 100 (200, 400) nm or the vertical axis of 1000 nm, respectively. This work advances our understanding of how to improve light trapping based on the symmetry breaking from the CNWs to ENWs and provides a rational way for designing high-efficiency single or self-assembled NW photovoltaic devices.

Thanks to advanced semiconductor microfabrication technology, chip-scale integration and miniaturization of lab-on-a-chip components, silicon-based optical biosensors have made significant progress for the purpose of point-of-care diagnosis. In this review, we provide an overview of the state-of-the-art in evanescent field biosensing technologies including interferometer, microcavity, photonic crystal, and Bragg grating waveguide-based sensors. Their sensing mechanisms and sensor performances, as well as real biomarkers for label-free detection, are exhibited and compared. We also review the development of chip-level integration for lab-on-a-chip photonic sensing platforms, which consist of the optical sensing device, flow delivery system, optical input and readout equipment. At last, some advanced system-level CMOS-chip packaging examples are presented, indicating the commercialization potential for the low cost, high yield, portable biosensing platform leveraging CMOS processes.

Silicon light funnels are three-dimensional subwavelength structures in the shape of inverted cones with respect to the incoming illumination. Light funnel arrays can serve as an efficient absorbing layers on account of their light trapping capabilities associated with the presence of high density complex Mie modes. Specifically, light funnel arrays exhibit broadband absorption enhancement of the of the solar spectrum. In the current study, we numerically explore the optical coupling between surface light funnel arrays and underlying substrates. We show that the absorption in LF array-substrate complex is higher than the absorption in LF arrays of the same height (~10% increase). This, we suggest, imply that a LF array serves as an efficient surface element that imparts additional momentum components to the impinging illumination, and hence optically excites the substrate by near-field light concentration, excitation of traveling guided modes in the substrate and mode hybridization.

This article will briefly review the progress of h-BN based solid-state metal semiconductor metal (MSM) neutron detectors. In the last decade, several groups have been working on hexagonal boron nitride (h-BN) based solid-state neutron detectors. Recently, the detection efficiency of 59% has been reported. Efficient, low-cost neutron detectors made from readily available materials are essential for various applications. Neutron detectors are widely used to detect fissile materials and nuclear power plants for security applications. The most common and widely used neutron detectors are 3He based, which are sometimes bulky, difficult to transport, have high absorption length, need relatively high bias voltage (>1000 V), and have low Q-value (0.764 MeV). Also, 3He is not readily available material. Thus, there is a strong need to find an alternative detection material. 10B isotope has a high neutron absorption cross-section, and it has been tested as a coating on the semiconducting materials. Due to the two-step process, neutron capture through 10B, and then electron-hole pair generation in a typical semiconducting material, the efficiency of these devices is not up to the mark. The progress in h-BN based detectors requires a review to envision the further improvement in this technology.

We attempted to apply the optoelectronic sensor entitled 'OPT101' in intensive care unit clinics, based on its optoelectronic response characteristics in near-infrared wavelength range and near-infrared spectroscopy principle. The successful novel applications in our lab include early-diagnosis and therapeutic effect tracking of thrombus, noninvasive monitoring of patients' shock severity, and fatigue evaluation. This study also expects further improvements of the detector in noninvasive clinical applications.

Forty-eight Pasteurella multocida isolates were recovered from porcine pneumonic lungs collected in Norwestern Spain (2017- 2019). These isolates were characterized for their minimal inhibition concentrations to twelve antimicrobial agents and for the appearance of eight resistance genes: tetA, tetB, blaROB1, blaTEM, ermA, ermC, mphE and msrE. Relevant resistance percentages were shown to teracyclines, sulphamethoxazole/trimethoprim and tiamulin, thus suggesting that P. multocida isolates were mostly susceptible to amoxicillin, ceftiofur, enrofloxacin, florfenicol, marbofloxacin and macrolides. 29.2% of isolates were resistant to more than two antimicrobials. The tetracycline resistance genes (tetA and tetB) were detected in 22.9% of the isolates, but none was positive to both simultaneously; blaROB1 and blaTEM genes were found in one third of isolates but both genes were detected simultaneously in only one isolate. ermC gene was observed in 41.7% of isolates, a percentage that decreased until 22.9% for msrE; finally, ermA was harboured by 16.7% and mphE was not found in any of them. Six clusters were established based on hierarchical clustering analysis on antimicrobial susceptibility for the twelve antimicrobials. Generally, it was unable to foresee the antimicrobial susceptibility pattern for each family and the association of each particular isolate inside the clusters established from the presence or absence of the resistance genes analyzed.

Energy transition is one of the greatest challenges facing humanity today. All micro, small, medium and large enterprises in operation will have to face it, and some can al-ready boast the first successes in this regard. This paper focuses on the involvement of these smallest players in energy transition. Micro and small entities are the largest part of the economy, having a great influence on its development. Looking at the wide scale of their activities, these entities are distinguished by a specific owner-manager relationship. This means that the final decision-making is influenced by business goals, but also by the manager's approach, their awareness of changes, and personal and other factors. Based on a structured and standardized survey questionnaire, the research was carried out using the Computer-Assisted Telephone Interviewing technique between April and May 2022 among owners of micro and small enterprises operating in Poland. The survey showed that active engagement of micro and small enterprises in energy efficiency initiatives is related to their market success and financial health.

We report a photonic-based radio frequency (RF) arbitrary waveform generator (AWG) using a soliton crystal micro-comb source with a free spectral range (FSR) of 48.9 GHz. The comb source provides over 80 wavelengths, or channels, that we use to successfully achieve arbitrary waveform shapes including square waveforms with a tunable duty ratio ranging from 10% to 90%, sawtooth waveforms with a tunable slope ratio of 0.2 to 1, and a symmetric concave quadratic chirp waveform with an instantaneous frequency of sub GHz. We achieve good agreement between theory and experiment, validating the effectiveness of this approach towards realizing high-performance, broad bandwidth, nearly user-defined RF waveform generation.

A switchable and tunable terahertz (THz) metamaterial based on photosensitive silicon and Vanadium dioxide (VO2) was proposed. By using finite-difference time-domain (FDTD) method, the transmission and reflective properties of the metamaterial were investigated theoretically. The results imply that, the metamaterial can realize a dual electromagnetically induced transparency (EIT) or two narrow-band absorption depending on the temperature of the VO2. Additionally, the magnitude of the EIT and two narrow-band absorption can be tuned by varying the conductivity of photosensitive silicon (PSi) via pumping light. Correspondingly, the slow light effect accompanying the EIT can also be adjusted.

Unmanned Aerial Vehicles (UAVs) image object detection has great application value in military and civilian fields. However, the objects in the captured images from UAVs have problems of large scale variation, complex backgrounds, and a large proportion of small objects. To resolve these problems, a multi-scale object detector based on coordinate and global information aggregation is proposed, named CGMDet. Firstly, a Coordinate and Global Information Aggregation Module (CGAM) is designed by aggregating local, coordinate, and global information, which can obtain features with richer context information. Secondly, a Multi-Feature Fusion Pyramid Network (MF-FPN) is proposed, which can better fuse features of different scales and obtain features containing more context information through repeated use of feature maps, to better detect multi-scale targets. Moreover, more location information of low-level feature maps is integrated to improve the detection results of small targets. Furthermore, we modified the bounding box regression loss of the model to make the model more accurately regress the bounding box and faster convergence. Finally, the proposed CGMDet was tested on VisDrone and UAVDT datasets and mAP0.5 of 50.9% and 48% was obtained, respectively. At the same time, our detector achieved the best results compared to other detectors.

The evolution of photovoltaic cells is intrinsically linked to advancements in the materials from which they are fabricated. This review paper provides an in-depth analysis of the latest developments in silicon-based, organic, and perovskite solar cells, which are at the forefront of photovoltaic research. We scrutinize the unique characteristics, advantages, and limitations of each material class, emphasizing their contributions to efficiency, stability, and commercial viability. Silicon-based cells are explored for their enduring relevance and recent innovations in crystalline structures. Organic photovoltaic cells are examined for their flexibility and potential for low-cost production, while perovskites are highlighted for their remarkable efficiency gains and ease of fabrication. The paper also addresses the challenges of material stability, scalability, and environmental impact, offering a balanced perspective on the current state and future potential of these material technologies.

This research will examine the computational methods to calculate the nonlinear optical process of second harmonic generation (SHG) that will be hypothesized to be present during lithium ion insertion into silicon nanowires. First it will be determined whether the medium in which SHG is conveyed is non-centrosymmetric or whether the medium is inversion symmetric where SHG as a part of the second-order nonlinear optical phenomenon does not exist. It will be demonstrated that the main interaction that determines SHG is multiphoton absorption on lithium ions. The quantum harmonic oscillator (QHO) is used as the background that generates coherent states for electrons and photons that transverse the length of the silicon nanowire. The matrix elements of the Hamiltonian which represents the energy of the system will be used to calculate the probability density of second-order nonlinear optical interactions which includes collectively SHG, sum-frequency generation (SFG) and difference-frequency generation (DFG). As a result it will be seen that at varies concentrations of lithium ions (Li+) within the crystallized silicon (c-Si) matrix the second-order nonlinear optical process has probabilities substantial enough to create second harmonic generation that could possibly be used for such applications as second harmonic imaging microscopy.

The refractive index of seawater is one of the essential parameters in ocean observation, so it is necessary to achieve high precision seawater refractive index measurement. In this paper, we propose a method for measuring the refractive index of seawater based on a Position Sensitive Detector (PSD). Theoretical model is established to depict the correlation between laser spot displacement and refractive index change, utilizing a combination of position sensitive detector and laser beam deflection principle. Based on this optical measurement method, a seawater refractive index measurement system was established. To effectively enhance the sensitivity of refractive index detection, a focusing lens was incorporated into the optical path of the measuring system, and simulations were conducted to investigate the impact of focal length on refractive index sensitivity. The calibration experiment of the measuring system was performed based on the relationship between refractive index of seawater and underwater pressure (depth). By measuring laser spot displacement at different depths, changes in displacement with respect to both refractive index and depth were determined. Experimental results demonstrate that the system exhibits a sensitivity of 9.9277×10−9RIU (refractive index unit), the refractive index deviation due to stability is calculated as ±7.545×10−9RIU. Thereby the feasibility of highly sensitive measurement of seawater refractive index is verified.

The shortwave infrared Ge-Si photodetector will become the core device of the LiDAR optical receiver. In order to meet the urgent demand for photodetectors in the LiDAR field, we have designed and produced a 32×32 pixel Ge-Si photodetector array proposed and developed to meet the performance requirements of the detector array. A dark current detection system for fast scanning and detecting large-scale Ge-Si detector arrays is proposed and developed to achieve rapid detection of dark current in each pixel of the detector. The system was used to validate the main performance indicators of the detector array we designed, achieving rapid discrimination of array performance and rapid localization of damaged pixels. The scanning test results show that the average dark current of the detector array chip we designed is at the nano ampere level, and the proportion of bad points is less than 1%. The consistency of the array chip is high, which can meet the requirements of light detection at the receiving end of the LiDAR. This work laid the foundation for our subsequent development of a LiDAR prototype system.

In this work, PMMA(Poly methyl methacrylate) microfluidic system was used as a micro-reactor for urea hydrolysis by urease enzyme with use conductivity principle and utilize sound level meter(SLM) App in smartphone as a novel detector by considering the peak height in the App as an indicate for urea concentration. the advantage of use small volume and how the reaction carried on in the microfluidic system with simple and low cost are discussed, and the results were analyzed and statically determine. The linearity, detection limit (3×noise )and Correlation Coefficient, 62.5-500 ppm, 31.25 ppm and 0.992 respectively also, recovery studied were between(98.5-100.13%).

The main consequence of radiation damage on a Silicon-Photomultiplier (SiPM) is a significant increase in the dark current. If the SiPM is not adequately cooled, the power dissipation causes it to heat up, which in turn affects its performance based on the temperature. In order to investigate this heating effect, experiments were carried out using a KETEK SiPM glued on an Al2O3 substrate, as well as HPK SiPMs that were either glued onto an Al2O3 substrate or a flexible PCB. The assemblies were connected either directly to a temperature-controlled chuck on a probe station or through layers of materials with well-defined thermal resistance. A DC-mode LED was used to illuminate the SiPM, and the resulting SiPM current was measured to determine the steady-state temperature. This temperature depended on the power dissipated in the multiplication region of the SiPM and the thermal resistance. This information can be utilized to adjust the SiPMs working point, taking into account the effects of self-heating. Similarly, this approach can be applied to packaged SiPMs that have an unknown thermal contact to a heat sink.

The tandem Solar cell has high power conversion efficiency (PCE), so they are taken as the next step in photovoltaic evolution. The tandem solar cell also overcome the limitations of Single-junction solar cells by reducing thermalization losses and also reduce the fabrication cost. The fabrication of tandem solar cells is highly efficient after the origination of halide perovskite absorber material, this material will shape the future of tandem solar cells. Researchers have already shown that this material can convert light more efficiently than standalone sub cell. Today, researchers around the world are keeping the configuration of a tandem solar cell as their agenda. A Tandem solar cell is a stacking of multiple layers having different bandgaps with specific maximum absorption and width. We reviewed perovskite/silicon tandem solar cells with different sub-module configurations. Move forward, we discuss the tandem module technology, sub cell of a tandem can be wired in several ways two terminals 2T monolithic and mechanically stacked, a four-terminal 4T mechanically stacked, and three-terminal 3T monolithic stack devices. This review paper provides a side-by-side comparison of theoretical efficiencies of multijunction solar cells. The highest efficiency has been evaluated at 39.4% for a three-level structure.

Micro/Nano Robot is an intelligent and efficient microrobot that can perform specific tasks under the influence of external stimuli. Depending on the application scenarios, the microrobot can adaptively transform into appropriate functional forms under different external stimuli, thus perfectly matching the needs. To date, microbots have been widely used in targeted therapy, drug delivery, tissue engineering, environmental remediation, and other fields. Although the applications of microrobots are promising, there are only a few reviews that can focus on the preparation methods and driving mechanisms. Therefore, it is necessary to outline the current status of the development of these microrobots in order to provide some new insights for the further development of the field. Therefore, this paper reviews the research progress of microrobots in terms of preparation methods, stimulus response mechanisms and applications, and highlights the applicability of different preparation methods and stimulus types. Finally, the current challenges faced by microrobots are highlighted and possible solutions are proposed to facilitate the practical application of microrobots.

When describing the tribological behaviour of technical surfaces, the need for full length scale microtopographic characterization often arises. The self-affine of surfaces and the characterization of self-affine by a fractal dimension and its implantation into tribological models are commonly used. The goal of our present work was to determine the frequency range of fractal behaviour of surfaces by analysing the microtopographic measurements of a brake plunger. We also wanted to know if the bifractal and multifractal behaviour can be detected in real machine parts. As a result, we developed a new methodology for determining the fractal range boundaries to separate the nano- and micro-roughness. In order to reach our goals, we used atomic force microscope (AFM) and stylus instrument to provide measurements in wide frequency range (19 nm - 3 mm). As a result of the power spectral density (PSD) based fractal evaluation, it was found that the examined surface could not be characterized by a single fractal dimension and that we developed a methodology for stopping the margin of validity of each fractal dimension, and we also developed a methodology for determining the limits of validity of certain fractal dimensions.

A micro decision-making utility model under uncertainty is presented as a complementary foundation for macro coronavirus models. The micro model consists of two functions, a risk averse utility function depending on wellness and a wellness random output which is a function of the input variable called “treatment” consisting of such elements as social distance, washing hands, wearing a face mask, and others. The decision maker selects a level of treatment that maximizes her/his expected utility, given the probabilities of the respective outputs. The focus is on how changes in a person’s psychological attitude towards the macro determined (announced) probabilities affects the optimum results of the model. Such changes create a micro-macro dynamic interaction which is briefly outlined. A short discussion of the model’s behavioral implications for health policy is also given.

The processes of hydrogen reduction of silicon and germanium chlorides under the conditions of high-frequency (40.68 MHz) counteracted arc discharge stabilized between two rod electrodes are investigated. The main gas-phase and solid products of plasma-chemical transformations are determined. Thermodynamic analysis of SiCl4 + H2 and GeCl4 + H2 systems for optimal process parameters was carried out. Using the example of hydrogen reduction of SiCl4 by the method of numerical modeling, gas-dynamic and thermal processes for this type of discharge are investigated. The impurity composition of gas-phase and solid reaction products is investigated. The possibility of single-stage production of high-purity Si and Ge mainly in the form of compact ingots, as well as high-purity chlorosilanes and trichlorogermane, is shown.

Tamm Plasmon Polariton (TPP) is a nanophotonic phenomenon that has attracted much attention due to its spatial strong field confinement, ease of mode excitation and polarization independence. TPP has applications in sensing, storage, lasing, perfect absorber, solar cell, nonlinear optics, and many others. In this work, we demonstrate a biosensing platform based on TPP resonant mode. Both theoretical analyses based on Transfer Matrix Method and experimental validation through nonspecific detection of liquids of different refractive indices and specific detection of SARS-CoV-2 nucleocapsid protein (N-protein) are presented. Results show that TPP biosensor has high sensitivity and good specificity. For N-protein detection, the sensitivity is 1.5 nm/(µg/ml) and the limit of detection can reach down to below 7 ng/ml with spectrometer of 0.01 nm resolution of wavelength shift. This work paves the way for design, optimization, fabrication, characterization, and performance analysis of TPP based biosensors

Electro-optic modulator (EOM) is one of the key devices of high-speed optical fiber communication system and ultra-wideband microwave photonic system. Silicon-organic hybrid (SOH) integration platform combines the advantages of silicon photonics and organic materials, providing a high electro-optic effect and compact structure for photonic integrated devices. In this paper we present a SOH integrated EOM with comprehensive investigation of EOM structure design, silicon waveguide fabrication with Slot structure, on-chip poling of organic electro-optic material, and characterization of EO modulation response. The SOH integrated EOM is measured with 3dB-bandwidth of over 50 GHz and half-wave voltage length product of 0.26 V·cm. Furthermore, we demonstrate a microwave photonics phase shifter by using the fabricated SOH integrated dual parallel Mach-Zehnder modulator. The phase shift range of 410 degree is completed from 8 GHz to 26 GHz with a power consumption of less than 38 mW.

Detecting rotational objects in remote sensing imagery is a significant challenge. These images typically encompass a broad field of view, featuring diverse and intricate backgrounds, with ground objects of various sizes densely scattered. As a result, identifying objects of interest within these images is a daunting task. While the integration of Convolutional Neural Networks (CNN) and Transformer networks leads to some advancements in rotational object detection, there is still room for improvement, particularly in enhancing the extraction and utilization of information related to smaller objects. To address this, our paper presents a multi-scale feature fusion module and a global feature context aggregation module. Initially, we fuse original, shallow, and deep features to reduce the loss of shallow feature information, thereby improving the detection performance of small objects in complex backgrounds. Subsequently, we compute the correlation of contextual information within feature maps to extract valuable insights. We name the newly proposed model the "Multiscale Feature Context Aggregation Module" (MFCA). We evaluate our proposed methodology on three challenging remote sensing datasets: DIOR-R, HRSC, and MAR20. Comprehensive experimental results show that our approach surpasses baseline models by 2.07\% mAP, 1.02\% mAP, and 1.98\% mAP on the DIOR-R, HRSC2016, and MAR20 datasets, respectively.

Automatic target detection of remote sensing images (RSI) plays an important role in military reconnaissance, disaster monitoring, and target rescue. The core task of remote sensing target detection is to judge the target categories and complete precise location. However, the existing target detection algorithms have limited accuracy and weak generalization capability for remote sensing images with complex backgrounds. To achieve accurate detection of different categories targets in remote sensing images, this study presents a novel feature enhancement single shot multibox detector (FESSD) algorithm for remote sensing target detection. The FESSD introduces feature enhancement module and attention mechanism into the convolution neural networks (CNN) model, which can effectively enhance the feature extraction ability and nonlinear relationship between different convolution features. Specifically, the feature enhancement module is used to extract the multi-scale feature information, and enhance the model nonlinear learning ability; the self-learning attention mechanism (SAM) is used to expand the convolution kernel local receptive field, which makes the model extract more valuable features. In addition, the nonlinear relationship between different convolution features is enhanced using the feature pyramid attention mechanism (PAM). The advantage of FESSD over other state-of-the-art target detection methods is validated by experiments on the presented seven-class target detection dataset (SD-RSI) and the public DIOR dataset.

Synchrotron radiation computed tomography (SRCT) allows more accurate calcified plaque and coronary stenosis assessment as a result of its superior spatial resolution, however, typical micro-computed tomography (micro-CT) systems have even higher resolution. The purpose of this study was to compare performance of high-resolution micro-CT with SRCT in the assessment of calcified plaques and a previously published dataset of coronary stenosis assessment. This experimental study involved micro-CT scanning of three-dimensional printed coronary artery models with calcification in situ used in our previously published SRCT study on coronary stenosis assessment. Measurements of coronary stenosis utilizing both modalities were compared using a paired sample t-test. The degrees of stenosis measured on all but one micro-CT dataset were statistically significantly lower than the corresponding SRCT measurements reported in our previous paper (p<0.0005-0.05). This indicates that the superior spatial resolution of micro-CT was able to further reduce over-estimation of stenosis caused by extensive calcification of coronary arteries and hence false positive results. This study shows that high-resolution micro-CT outperforms SRCT in both calcified plaque and coronary stenosis assessment. This finding will become clinically important for cardiovascular event prediction and enable reclassification of individuals with low and intermediate risk into appropriate risk categories when the technical challenges of micro-CT in clinical practice such as the small field of view and demanding on image processing power are addressed.

Bimetallic Ni/Cu core-shell and Cu-Ni heterostructural micro- and nanoparticles were prepared using two simple successive reduction procedures. Monometallic Ni and Cu particles were synthesized for comparison. The phase constitutions and morphological features of the particles were studied by means of X-ray diffraction, energy-dispersive X-ray spectroscopy and scanning electron microscopy methods. All the obtained mono- and bimetallic particles were applied as electrocatalysts in the electrohydrogenation of p-nitrophenol (p-NPh). An additional electrochemical reduction of copper cations during the hydrogen saturation of Cu-containing particles was established. Some of the prepared particles exhibited high catalytic activity with an increase in the hydrogenation rate of p-NPh by more than 3 times compared to its electrochemical reduction on the non-activated cathode, and p-NPh conversion yielded the maximum values. The main product of p-NPh electrocatalytic hydrogenation over Ni-Cu particles is p-aminophenol, which is an intermediate in the synthesis of many drugs. p-Aminophenol formation is confirmed by UV-Vis spectra.

Silicon has been proved to be one of the most promising anode materials for the next generation of lithium-ion battery. For the application in batteries, Si anode should have high capacity and must be industrially scalable. In this study, we have designed and synthesised a hollow structure to meet these requirements. All the processes are carried out without special equipment. The Si nanoparticles that are commercially available are used as the core sealed inside TiO₂ shell, with rationally designed void space between the particles and shell. The Si@TiO₂ are characterised using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and scanning electron microscope (SEM). The optimised hollow structured silicon nanoparticles, when used as anode in lithium-ion battery, exhibit a high reversible specific capacity over 600 mAhg-1. This excellent electrochemical property of the nanoparticles can be attributed to their optimised phase and unique hollow nanostructure.

We successfully created a composite photonic structure out of porous silicon (PSi) microcavities doped by the photochromic protein, photoactive yellow protein (PYP). Massive incorporation of the protein molecules into the pores was substantiated by a 30-nm shift of the resonance dip upon functionalization, and light-induced reflectance changes of the device due to the protein photocycle were recorded. Model calculations for the photonic properties of the device were consistent with earlier results on the nonlinear optical properties of the protein, whose degree of incorporation into the PSi structure was also estimated. The successful proof-of-concept results are discussed in light of possible practical applications in the future.

In this paper, we review devices used in silicon photonic switches. Devices in switches are divided into active and passive devices. Active devices consist of microring resonator, contra directional couplers, mach zhender switches. Passive devices consist of waveguide crossings and arrayed waveguide gratings. We also list the state of the art in devices in a comparison table.

The detection performance of small objects in remote sensing images has not been satisfactory compared to large objects, especially in low-resolution and noisy images. A generative adversarial network (GAN)-based model called enhanced super-resolution GAN (ESRGAN) showed remarkable image enhancement performance, but reconstructed images usually miss high-frequency edge information. Therefore, object detection performance showed degradation for small objects on recovered noisy and low-resolution remote sensing images. Inspired by the success of edge enhanced GAN (EEGAN) and ESRGAN, we applied a new edge-enhanced super-resolution GAN (EESRGAN) to improve the quality of remote sensing images and used different detector networks in an end-to-end manner where detector loss was backpropagated into the EESRGAN to improve the detection performance. We proposed an architecture with three components: ESRGAN, EEN, and Detection network. We used residual-in-residual dense blocks (RRDB) for both the ESRGAN and EEN, and for the detector network, we used a faster region-based convolutional network (FRCNN) (two-stage detector) and a single-shot multibox detector (SSD) (one stage detector). Extensive experiments on a public (car overhead with context) dataset and another self-assembled (oil and gas storage tank) satellite dataset showed superior performance of our method compared to the standalone state-of-the-art object detectors.

There is an important complementarity between experimental methods for the study of high-temperature viscoelasticity in the time and frequency domains, that has not always been fully exploited. Here we show that parallel processing of forced-oscillation data and microcreep records, involving consistent use of either Andrade or extended Burgers creep-function models, yields a robust composite modulus-dissipation dataset spanning a broader range of periods than either technique alone. In fitting this dataset, the alternative Andrade and extended Burgers models differ in their partitioning of strain between the anelastic and viscous contributions. The extended Burgers model is preferred because it involves a finite range of anelastic relaxation times, and accordingly a well-defined anelastic relaxation strength. The new strategy offers the prospect of better constraining the transition between transient and steady-state creep, or equivalently, between anelastic and viscous behaviour.

This article develops algorithms for the characterization and the visualization of micro-scale features by using a small number of sample points, and with a goal to mitigate for the measurement shortcomings which are often destructive or time consuming. We implement the algorithms to rapidly examine the microscopic features of a Microelectromechanical System (MEMS) surface. Such images are highly dense; therefore, traditional image processing techniques might be computationally expensive. The contribution of this research include first, we develop local and global algorithm based on modified Thin Plate Spline (TPS) model to reconstruct high resolution images of the micro-surface’s topography, and its derivatives by using low resolution images. Second, we obtain a bending energy algorithm from our modified TPS model, and use it to filter out image defects. Finally, we develop a computationally efficient Windowing technique, which combines TPS and Linear Sequential Estimation (LSE), to enhance the visualization of images. The Windowing technique allows rapid image reconstruction based on the reduction of inverse problem.

During the 16th and 17th centuries, Latin American cities adopted earthen construction techniques from European colonizers. As a result, rammed earth (RE) buildings now occupy an important place in Latin America's cultural heritage. However, earthquakes around the world have shown that unreinforced earthen constructions are highly vulnerable. For several years, researchers in northern South America have been proposing a technique that consists of installing confining steel plates (or wooden elements) on both sides of the RE walls forming a grid. This system has shown excellent performance in controlling seismic damage and increasing strength and ductility capacity. Although researchers have tested full-scale one- and two-story earthen walls under pseudo-static loading in the laboratory, and one- and two-story earthen walls at 1:1 and 1:2 scale on uniaxial and biaxial shaking tables, the behavior of a complete reinforced module (one- or two-story) on a shaking table has never been assessed. The present study presents the results of shaking table tests performed on two-story RE modules at 1:4 scale. The experimental data indicate that the retrofit system with confining steel strips was effective in reducing the seismic damage of earthen constructions. In addition, the comparison of the results of the 1:4 scale tests with the 1:2 and 1:1 scale tests previously conducted by the researchers, shows that the acceleration levels of the equivalent prototypes are in the same order of magnitude for the three scales.

In this study, Silicon Carbide (SiC) nano-particle based serigraphic printing inks were formulated to fabricate highly sensitive and wide temperature range SiC printed thermistors. Initially, commercial silver ink was screen printed to fabricate inter-digitated electrodes (IDE’s) onto flexible Kapton® substrate via screen printing. Thermistor inks with different weight ratios of SiC nano- particles dispersed in polyimide resin matrix were fabricated. The SiC-polyimide temperature sensing inks were screen printed atop the IDE structures to form fully printed thermistors and encapsulated with a adhesive backed polyimide film for humidity inhibition. The high temperature tolerance of the Kapton® allowed the the sensors to be tested over a wide temperature range form 25◦C to 170◦C. The printed SiC thermistors exhibit excellent repeatability and stability over 15 hours of continuous operation. Optimal device performance was achieved with 30 wt.% SiC-polyimide ink. We report highly sensitive devices with a temperature coefficient of Resistance (TCR) of -0.556 %/◦C, a thermal coefficient of 502 K (β-index) and an activation energy of 0.08 eV which are comparable with printed thermistors previous reported. Further, the thermistor demonstrates an accuracy of ±1.35◦C which is well within the range offered by commercially available high sensitivity thermistors. SiC thermistors exhibit a small 6.5% drift due to changes in relative humidity between 10-90 %RH and a 4.2 % drift in baseline resistance after 100 cycles of aggressive bend testing at a 40°angle. The use of commercially available low cost materials, simplicity of design and fabrication techniques coupled with the chemical inertness of the Kapton® substrate and SiC nanoparticles paves the way to use all-printed SiC thermistors towards a wide range of applications where temperature monitoring is vital for optimal system performance.

Keywords: Amorphous-precipitate, Nitride, Morphological stability, Diffusion, Internal stresses, Modelling, Simulation