Spatiotemporal variations of sediments transported along rivers play a crucial role in a wide spectrum of uses, such as navigation, recreation, habitats or hydropower production. The advancement in technology has made it possible to use various indirect techniques to study and evaluate the transport of suspended sediment in fluvial environments. To investigate large-scale phenomena, remote sensing is becoming a largely utilized approach, as it allows to combine spatially-distributed and local information. Dam-induced sediment reduction occurs in large and small rivers worldwide, having profound implications on the fluvial systems. However, the systematic change of suspended sediment concentration (SSC) and its dynamic processes are not well known, and generally investigated only at the very local scale using field information. In this work, SSC maps were created by combining satellite images with local monitoring SSC data, using the Zhijiang -Chenglingji reach of the Changjiang River (China) as a case study, and analyzing how SSC dynamics changed over the period 2017-2022 in correspondence of extreme events. Multiple relationships between measured SSC and bands reflectance were tested, showing the potential of the best-performing one (R2=0.43) in mapping SSC spatiotemporal variations over an extent of dozens of kilometres, eventually providing new insights into the SSC dynamics at hotspots of the river systems, such as confluence zones, barriers, and reservoirs.

The intrinsic non-linearity and complexity of suspended sediment dynamics, which are impacted by the geographical variability of basin parameters and temporal climatic patterns, make it difficult to estimate suspended sediment concentration (SSC) accurately in hydrological processes. Deep neural networks (DNNs), a cutting-edge modeling method that can capture the innate non-linearity in hydrological systems, have emerged as a solution to this problem. Using primary data on discharge, SSC, and turbidity, the long short-term memory method of DNNs was employed in this study to simulate the discharge-suspended sediment connection for the Esopus Creek, NY, USA as the first objective. To develop effective modeling strategies, multiple scenarios of feature selection, including combinations of discharge, turbidity and SSC for preceding days, were considered. Secondly, the variations in SSC and discharge between the three USGS gages along Esopus Creek that were upper stream, lower stream, and downstream, adjacent to the pourpoint were analyzed. Statistical metrics and scenarios of feature importance were used to evaluate the effectiveness of the DNN-based models. The study shows that among 24 DNN approaches feature selection is crucial in simulating the daily SSC, and discharge and presenting novel research directions for utilizing machine learning algorithms in water quality.

Lake sediment records are of great importance for understanding the evolution of watershed environments. Various studies have been carried out to constrain the depositional ages of lake sediments and examine their physical, chemical, and biological characteristics, aiming to construct historical vegetation, environment and climate patterns in Chinese lake watersheds. In this study, we obtained relevant literature on lake sediment records by searching the key word 'age-depth' from the databases – Web of Science and China National Knowledge Infrastructure (CNKI, the largest Chinese academic database). We analyzed the literature based on its type (published in a Chinese/English journal or as a Master’s/PhD thesis), period of publication, journal (if published in a journal), key authors, study area, dating scale, and main aims. The results suggest that the lakes in the plateau regions are the most popular research topic typically covering 100–200 years (short-term) and 500–30,000 years (long-term). The literature focuses on a wide range of topics, from past environmental evolution in the watershed to lake ecology, and provides a solid foundation for better understanding regional climate change and the preservation of lake environments and ecosystems. In the future, resulting data from environmental reconstruction with lake sediments will be needed to integrate with emerging information processing technologies (e.g., artificial intelligence and meta-analysis), to disentangle the complex interplay between Earth surface processes and global climate change; furthermore, strengthening interdisciplinary collaboration will deepen our comprehension of man-land relationship and promote the sustainable management of lake ecosystems in the context of global climate change.

In this paper, we consider a fourth-order suspension bridge equation with nonlinear damping term |u_t|^m-2u_t and source term |u|^p-2u. We give necessary and sufficient condition for global existence and energy decay results without considering the relation between m and p. Moreover, when p>m, we give sufficient condition for finite time blow-up of solutions. The lower bound of the blow-up time T_max is also established. It worth to mention that our obtained results extend the recent results of Wang (J. Math. Anal. Appl., 2014) to the nonlinear damping case.

In the industrial production of olive oil, both solid wastes and those produced from their incineration are a serious environmental problem since only 20% w/w of the fruit becomes oil and the rest is waste, mainly orujo and alperujo. A key aspect to transform these wastes into an important source of energy such as pellets is to recognize the most appropriate time of the year for waste drying, with the objective of minimizing the environmental impact of the volatile compounds contained in the waste. In this work, the emissions produced during thermal-mechanical drying were studied along a period of six months of waste storage in which alperujo and orujo were stored in open containers under uncontrolled environmental conditions. The studied emissions were produced when both wastes were dried in a pilot rotary drying trommel at 450ºC to reduce their initial humidity of around 70-80% w/w to 10-15% w/w. Results indicated that when the storage time of the wastes in uncontrolled environments increases, the emission of odorant compounds during drying also increases as a consequence of the biological and chemical processes occurring in the containers during waste storage. The main odorant VOCs were quantified monthly for six months at the outlet of the drying trommel. It was determined that the drying of this type of waste can be carried out properly until the third month of storage. Afterwards, the concentration of most VOCs produced widely exceeded the odor thresholds of selected compounds.

The mechanism underlying microbiologically induced carbonate precipitation have not been thoroughly characterized, although numerous scholars and experts have specifically investigated questions regarding minerals induced by bacteria. The study of the precipitation of carbonate minerals induced by halophilic bacteria has aroused wide concern. The present study aimed to investigate the characterization and process of biomineralization in high salt systems by a halophilic bacterium, Chromohalobacter israelensis strain LD532 (GenBank: KX766026), which was isolated from the Yinjiashan Saltern in China. Carbonate minerals induced by LD532 were investigated in several sets of comparative experiments that employed magnesium sulfate and magnesium chloride as Mg resources. Magnesium calcite and aragonite were induced by LD532 bacteria, whereas these minerals did not appear in the control group. The mineral phases, micromorphologies, and crystal structures were analysed using X-ray powder diffraction, scanning electron microscopy, and energy dispersive X-ray detection. The carbonic anhydrase and urease secreted by strain LD532 through metabolism increased the pH value of the liquid medium and promoted the process of carbonate precipitation. Further study using high resolution transmission electron microscopy, energy dispersive X-ray detection and analysis of ultrathin slices showed that the nucleation sites of carbonate minerals were located on extracellular polymeric substances and the membranes of intracellular vesicles of LD532 bacteria, which provided favourable conditions for the growth of carbonate mineral crystals. The morphologies and compositions of minerals formed in solutions of MgSO₄ and MgCl₂ display significant differences, indicating that different sources of Mg²⁺ may also affect the physiological and biochemical activities of microorganisms and thus mineral deposition. This study will be of some interest for the interpretation of carbonate biomineralization in natural salt environments and has some value as a reference in understanding sedimentary carbonates in ancient marine environments, such as tidal flats.

The paper presents a method to assess the effect of electrolyte additives on the energy capacity of Pb-acid batteries. The method applies to any chemically unreactive additive, including suspensions and gels. The approach is thermodynamically based and it leads to the definition of a region of admissible concentrations –the battery’s admissible range– where the battery can undergo an indefinite number of charge/discharge cycles without suffering permanent damage. An experimental procedure to determine this range is presented. The obtained results provide a way to assess the potential of electrolyte additives to improve the energy capacity of Pb-acid batteries. The same results also provide a means to determine the additive concentration that produces the maximum energy capacity increase of the battery. The paper closes with an example of application of the proposed approach to a practical case.

The information on the land use and soil conservation practice based on year 2006, 2010 and 2014, hence offering an opportunity to model the impacts of land use change on erosion, deposition and surface water runoff. Limitation in the use of hydrological models had been their inability to handle the large amount of input data that describe the heterogeneity of the natural system. In this study, a procedure that takes into account soil conservation practice based on the land use change, the response of soil erosion and sediment export from the George Town Conurbation catchment area, and average annual sediment yields were estimated for each grid cell of the watershed to identify the critical erosion areas of rural and urban planning proposes. Average annual sediment yield and data on a grid basis estimated using Universal Soil Loss Equation (USLE) and an emerging technology represented by Geographic Information System (GIS) used as a tool to produce a map for erosion rate. The changing of the land use from forest to agriculture and then to an urban area is a challenging task to research on land use demand for population, and environmental impact assessment is important for the planning of natural resources management, allowing research the modification of land use properly and implement more sustainable for long term management strategies. The challenge is to formulate strategies that would promote an integrated approach to the land use planning at an appropriate level as to address the issues that arose. Modelling for creating urban growth boundary for the George Town Conurbation must have to be controlled surface runoff and soil loss and sediment export from land use of the George Town Conurbation catchment.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

The increasing regulatory pressure to monitor and reduce GHG emissions and air pollutants requires cost-effective methods for their surveillance. The most common technique used for scientific investigations on gas concentration monitoring in barns are accurate but expensive and with a complex maintenance. This research study analysed the potential use of a low-cost portable measurement devices for the measurement of ammonia (NH3) and carbon dioxide (CO2) concentrations in an open dairy barn. A comparison between gas concentrations acquired at different heights from the floor by using portable devices and those acquired by a photoacoustic infrared multigas spectroscope (i.e., reference measurement) in the same sampling locations was carried out to determine the precision of the low-cost portable devices. The performance of low-cost portable devices was statistically analysed by the application of the one-way analysis of variance, correlation analysis and regression analysis. The results showed a significant difference between gas concentration values at various heights from the floor for both NH3 and CO2. The correlations between concentrations acquired by the low-cost portable device and the INNOVA were statistically significant (r=0.83; P<0.001) for gas concentrations monitored at 0.4 m from the floor. Compared with the reference measurement device, the low-cost devices were effective in the monitoring of NH3 concentrations at 0.40 m from the floor though it underestimated them in the barn at increasing of the height from the floor, whereas the device was not adequate for CO2 concentrations. In detail, the relative measurement error of the low-cost devices compared to INNOVA was reduced close to the floor during NH3 concentration measurements. Within these limitations, this device could be useful for monitoring NH3 concentration in the barn and to assess variation in NH3 concentrations mainly related to the animal occupied zone. Further efforts are needed in this field of research to identify low-cost device that could simplify emission estimation from open dairy barns.

This study explores the significance of active suspension systems for vehicles with lower chassis compared to conventional ones, aiming at the development of future automobiles. Conventional linear MR (Magneto-Rheological) dampers were found inadequate in ensuring sufficient vibration control because the vehicle's chassis becomes lowered in the unmanned vehicles or purposed based vehicles. As an alternative, a rotary type of MR damper is proposed in this work. The proposed damper is designed based on pre-specified design parameters through mathematical modeling and magnetic field analyses. Subsequently, a prototype of the rotary MR damper identical to the design is fabricated, and effectiveness is shown through experimental investigations. In configuring the experiments, a proportional-integral (PI) controller is employed for current control to reduce the response time of the damper. The results presented in this work provides useful guidelines to develop a new type of MR damper applicable to various types of future vehicles’ suspension systems with low distance from the tire to the body floor.

Sediment plumes, released to the Bering Sea from the delta front of the Yukon River, Alaska, are initiated mainly by glacier-melt sediment runoffs in the glacierized regions of the Yukon River drainage basin. The surface sediment plumes are extended around the fan-shaped Yukon River delta, which is followed by the northwestward dispersion. During continuous measure-ments of the Yukon River discharge and sediment load, behaviors of the sediment plumes were explored by shipboard observations in the Bering Sea offshore from the Yukon delta. At the high river sediment load of ca. 3000 kg/s, the plume partially plunged into the sea bottom layer. The plunging probably originated in the nepheloid-layer formation from the flocculation of river-suspended sediment, of which more than 90 %wt. is silt and clay (grain size d < 0.063 mm). In order to numerically obtain the area of the surface sediment plumes, a satellite image analy-sis was performed by using three near-infrared bands in MODIS/Aqua or MODIS/Terra. The plume area was significantly correlated (R2=0.735, p<0.01) to the sediment load averaged for the two days with time lags of 20 days and 21 days to the date of a certain satellite image. Hence, the dispersion of plume-suspended sediment appears to be controlled by the sediment runoff events in the Yukon River rather than the northward “Alaskan Coastal Water”.

The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of &gt;1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.

Solid particle cationic polyacrylamide (CPAM) is one of the most commonly used organic polymer flocculants in oilfield wastewater treatment, but there are some problems, such as slow dissolution rate, and easy to form a "fish-eye" in the process of diluting into aqueous solution. However, the current liquid CPAM products also have some problems, such as low effective content, poor storage stability, degradation in a short time and high preparation cost. In this paper, a secondary processing technology of solid particle CPAM was studied, and a CPAM suspension was successfully prepared. This suspension has an effective content of 50.00%, No separation in 7 days of storage at room temperature, no separation in 30 min of centrifugation at a speed of 2000 r/min, and diluted to a 0.40 % weak gel solution in just 16.00 min. For 1000 NTU of diatomite simulated wastewater, the optimal turbidity removal rate of the suspension was 99.50%, which was higher than the optimal turbidity removal rate of 98.40% for the inorganic flocculant polymeric aluminum chloride (PAC). For oil and gas field oily wastewater, the optimal turbidity removal rate of CPAM suspension was 35.60%, which was higher than the optimal turbidity removal rate of 28.40% for solid particle CPAM.

The awareness of the existence in plants of bioactive compounds namely phytochemicals (PHYs), having health properties is progressively expanding. Therefore, their massive introduction in the normal diet, in food supplements, and their use as natural therapeutics to treat several diseases are increasingly emphasized by several sectors. Particularly, most PHYs possessing antifungal, antiviral, anti-inflammatory, antibacterial, antiulcer, anti-cholesterol, hypoglycemic, immunomodulatory, and antioxidant properties have been isolated from plants. Additionally, their secondary modification with new functionalities, to further improve their intrinsic beneficial effects, is extensively investigated. Unfortunately, although the idea of exploiting PHYs as therapeutics is amazing, its realization is far from simple, and the possibility of exploiting them as effective orally administrable drugs is almost utopic. Most PHYs are insoluble in water and, when introduced orally, they scarcely reach the site of action in therapeutic concentrations. Degradation by enzymatic and microbial digestion, occurring in the mouth, stomach, and intestine, as well as fast metabolism and rapid excretion via the kidney, biliary, or lung, strongly limit their in vivo activity. To overcome these drawbacks, several nanotechnological approaches have been used and many PHYs-loaded delivery systems with dimensions of nanometers have been developed. This paper, also by reporting various recent case studies, reviews the foremost nano-suspension and nano-emulsion-based techniques developed for formulating the most relevant PHYs in more bioavailable nanoparticles (NPs), suitable or promising for clinical application. Also, the acute and chronic toxic effects due to the exposure to NPs reported so far, the possible nanotoxicity which could derive by their massive employment, as well as the ongoing actions to improve the knowledge in the field were discussed. The state of the art concerning the actual clinical application of both PHYs and the nanotechnologically engineered PHYs was also reviewed.

Plant stem cell cultures have so far been established in only a few plant species using cambial meristematic cells. The presence of stem cells or stem cell-like cells in other organs and tissues of the plant body, as well as the possibility of de novo generation of meristematic cells from differentiated cells, allows to consider the establishment of stem cell cultures in a broader range of species. Therefore, this study aimed to establish a stem cell culture of the medicinal plant Calendula officinalis L. Callus tissues were induced from explants taken from leaves and roots. Appropriate combinations of plant growth regulators and light parameters for in vitro cultivation were selected. Already at this stage, stem and dedifferentiated cells could be identified, and cell suspension cultures were established from specific parts of the formed callus. Cell suspension cultures with a high proportion of stem cells originating from roots (92–93%) or leaves (72–73%) were developed. The amount of stem cells derived from the roots in the cell suspension reached a plateau at a level of 5.60–5.72105.

In recent years, there has been growing interest in thermal spray techniques using suspension or solution-based coatings. These techniques offer precise control over particle size and microstructure, improving feedstock flowability and allowing for high-quality coatings customization. Spray parameters, such as stand-off distance (SOD) and feedstock flow rate, can alter the performance and characteristics of these coatings. Geothermal power plant heat exchangers often face issues like corrosion, scaling, and fouling. These issues could be mitigated, at least in part, by the use of spray coatings. In this study, TiO2 coatings were applied to a carbon steel substrate using suspension plasma spray (SPS) to enhance the performance of geothermal heat exchanger materials. The impact of SOD (50, 75, and 100mm) and feedstock flow rate (10, 20, and 30 ml/min) on these coatings was examined through various techniques, including SEM, profilometry, XRD, and adhesion testing. The results demonstrated that coatings deposited using 10ml/min feedstock flow rate were well-adhered to the substrate due to efficient melting of coating material but as the SOD and feedstock flow rate increase due to poor thermal and kinetic energy exchange between the torch and feedstock particles, adhesion between coating and substrate decreases. smaller SODs led to more compact coatings, while higher feedstock flow rates increased coating porosity. Smaller SODs and lower flow rates resulted in well-adhered coatings, offering valuable insights for advancing geothermal heat exchanger coatings.

Preventing the rebound of black and odorous water bodies is critical for improving the ecological environment of water bodies. This study investigated the effect and mechanism of in-situ improvement of sediment microenvironment by nitrate in tailwater of wastewater treatment plants combined with aerobic denitrifying bacteria under low-DO regulation (TailN+CFM+LDO). On the 60th day of remediation, the dissolved oxygen and oxidation-reduction potential in the overlying water increased to 5.6 mg/L and 300 mV, respectively, the acid volatile sulfide in the sediment decreased by 70.4%, and the organic matter in the sediment was reduced by 62.7%, in which the HFOM was degraded from 105 g/kg to 56 g/kg, and the potential risk of water reverting to black and odorous conditions significantly decreased. Amplicon sequencing analysis revealed that the relative abundance of electroactive bacteria Thiobacillus and Pseudomonas with denitrification capacity was found to be significantly higher in the TailN+CFM+LDO group than in the other remediation groups. Functional prediction of 16S sequencing results indicated that both the quantity and activity of critical microbial enzymes involved in nitrification and denitrification processes could enhance in the TailN+CFM+LDO group. These results improved our understanding of the improvement of the sediment microenvironment and could thus facilitate its application.

Human activities for exploitation and utilization of coastal zones have transformed coastline morphology and severely changed regional flow fields, underwater topography, and sediment distribution in the sea. In this study, single-beam bathymetry coupled with sediment sampling and analysis was carried out to ascertain submarine topography, geomorphology and sediment distribution patterns and explore sediment provenance in Qinzhou Bay, China. The results show the following. 1) The underwater topography in Qinzhou Bay is complex and variable, with water depths in the range of 0–20 m. It can be divided into four underwater topographic zones: the central (outer Qinzhou Bay), eastern (Sanniang Bay), western (east of Fangcheng Port), and southern (outside of the bay) parts. 2) Based on geomorphological features, the study area comprises four major submarine geomorphological units (i.e., tide-dominated delta, tidal sand ridge group, tidal scour troughs, and underwater slope) and two intertidal geomorphological units (i.e., tidal flat and abrasion platforms). 3) Sandy sediments are widely present in Qinzhou Bay, accounting for 70% of the total sediments. From the mouth of the Maowei Sea to the offshore, the sediments gradually become coarser, shifting from sandy mud to muddy sand, and then to fine sand and medium–coarse sand. The detrital minerals contained in the sediments mainly consist of quartz, feldspar, debris, ilmenite, leucosphenite, and tourmaline, whereas the clay minerals are dominated by kaolinite, followed by illite and smectite. The sediment provenance is mainly terrigenous input from near-source rivers. With sea reclamation and dam construction, outer Qinzhou Bay has experienced enormous morphological variation of its coastline. Together with the channel effect where the velocity of ebb tide is greater than that of flood tide, the underwater topography is characterized by increased scale and height difference of troughs and ridges as well as enhanced offshore deposition.

Human activities for exploitation and utilization of coastal zones have transformed coastline morphology and severely changed regional flow fields, underwater topography, and sediment distribution in the sea. In this study, single-beam bathymetry coupled with sediment sampling and analysis was carried out to ascertain submarine topography, geomorphology and sediment distribution patterns and explore sediment provenance in Qinzhou Bay, China. The results show the following. 1) The underwater topography in Qinzhou Bay is complex and variable, with water depths in the range of 0–20 m. It can be divided into four underwater topographic zones: the central (outer Qinzhou Bay), eastern (Sanniang Bay), western (east of Fangcheng Port), and southern (outside of the bay) parts. 2) Based on geomorphological features, the study area comprises four major submarine geomorphological units (i.e., tide-dominated delta, tidal sand ridge group, tidal scour troughs, and underwater slope) and two intertidal geomorphological units (i.e., tidal flat and abrasion platforms). 3) Sandy sediments are widely present in Qinzhou Bay, accounting for 70% of the total sediments. From the mouth of the Maowei Sea to the offshore, the sediments gradually become coarser, shifting from sandy mud to muddy sand, and then to fine sand and medium–coarse sand. The detrital minerals contained in the sediments mainly consist of quartz, feldspar, debris, ilmenite, leucosphenite, and tourmaline, whereas the clay minerals are dominated by kaolinite, followed by illite and smectite. The sediment provenance is mainly terrigenous input from near-source rivers. With sea reclamation and dam construction, outer Qinzhou Bay has experienced enormous morphological variation of its coastline. Together with the channel effect where the velocity of ebb tide is greater than that of flood tide, the underwater topography is characterized by increased scale and height difference of troughs and ridges as well as enhanced offshore deposition.

Anthropogenic activities such as the damming of rivers have resulted in the formation of depositional systems for sediments that are naturally transported along river channels all over the world. The steady accumulation of sediments has profound effects on how reservoirs function. As the reservoir ages, the impact of sedimentation becomes more pronounced. In an alluvial channel, the dynamics of sediment movement, scour, and deposition are exceedingly complicated. The quantitative and qualitative management of river engineering heavily relies on sediment motion. One of the key concerns affecting reservoir storage capacity is reservoir sedimentation. Understanding the form and behavior of the river or reservoir is necessary for a scientific approach to sedimentation. An overview of reservoir sedimentation processes, and models of reservoir and shallow water bodies is provided in this article. More research in the developing fields is advised for continuing studies on reservoir sedimentation due to climate change effects

In order to reduce the influence of ground vibration generated by tractor during driving and operation on driving stability and driver ride comfort, this paper proposes a control method of tractor active seat suspension based on model predictive control. By establishing a 3-degree of freedom tractor active seat suspension model and a ground excitation input model, a new model predictive controller for the active seat suspension system is designed. The vertical acceleration of the seat center of mass, the seat suspension stroke and the tire dynamic displacement are optimized by limiting the dynamic deflection of the seat suspension and the active force output of the actuator. The control model of MPC tractor active seat suspension system is built and its performance is simulated and verified. The results show that compared with the passive seat suspension and the PID seat suspension, the tractor active seat suspension based on model predictive control (MPC) has better damping characteristics and improves ride comfort.

The Casiquiare River is a natural channel that connects two of the greatest rivers in the world, the Orinoco and the Amazon in the South American Continent. The aim of this paper is to present a review and synthesis of the hydrological and sedimentological knowledge of the Casiquiare River, including the first hydro-sedimentary balance of the Casiquiare fluvial system conducted at the bifurcation and at the mouth on September 9-12, 2000, during the expedition ‘Humboldt-Amazonia 2000’. Bathymetric, flow discharge and physico-chemical measurements were made at the inlet and at the outlet of the Casiquiare Channel. The main conclusions of this study indicate that Casiquiare is taking a significant proportion of flow (20 to 30%) from the Upper Orinoco basin to the Amazon basin. Throughout its 356 km-course, this chameleon channel undergoes significant morphological, hydrological and bio-geochemical variations between the inlet and the outlet, whose most visible witnesses are the increase in its width (3 to 4 times), flow (7 to 9 times) and its change in water color (white to black water), under the influence of tributaries coming from vast forest plains.

The relation between CO2 emissions and atmospheric CO2 concentration has traditionally been treated with more or less complex models with several boxes. Our approach is motivated by the question of how much CO2 must necessarily be absorbed by sinks. Observations lead to the model assumption, that carbon sinks like oceans or biosphere are linearly dependent on CO2 concentration on a decadal scale. In particular this implies the falsifiable hypothesis that oceanic and biological CO2 buffers have not significantly changed in the past 50 years and are not saturated in the forseeable future. The simple model with 2 parameters explains very well the CO2 emission and historical CO2 concentration data. The model gives estimates of the natural emissions, the pre-industrial CO2 equilibrium concentration levels, the half-life time of an emission pulse, and the future CO2 concentration level from a given emission scenario. This is validated by an ex-post forecast of the last 20 years. The important result is that with the stated polices scenario of the IEA future CO2 concentrations will not rise above 475 ppm. The model is compared with the Carbon modul of the Bern model, mapping their complex IRFs to a single time variant parameter.

In order to coordinate the damping performance and energy regenerative performance of energy regenerative suspension, this paper proposes a structure of vehicle semi-active energy regenerative suspension with electro-hydraulic actuator (EHA). In light of the proposed concept, a specific energy regenerative scheme is designed and the mechanical properties test is carried out. Based on the test results, the parameter identification for the system model is conducted using recursive least squares algorithm. On the basis of system principle, the nonlinear model of the semi-active energy regenerative suspension with EHA is built. Meanwhile, LQG control strategy of the system is designed. And then the influence of the main parameters of EHA on the damping performance and energy regenerative performance of suspension is analyzed. Finally, the main parameters of EHA actuator are optimized via genetic algorithm. The test results show that when sinusoidal is input at the frequency of 2Hz and the amplitude of 30mm, the spring mass acceleration RMS value of optimized EHA semi-active energy regenerative suspension is reduced by 22.23% and energy regenerative power RMS value is increased by 40.51%, which means while meeting the requirements of certain vehicle ride comfort and driving safety, energy regenerative performance is improved significantly.

1) Landsat operational land imager (OLI) data and consequent laboratory measurements were used to predict Chlorophyll-a (Chl-a) concentration and the trophic states for an inland lake within the East Kolkata Wetland, India; 2) The most suitable band ratio was identified by performing Pearson correlation analysis between Chl-a concentrations and possible OLI band and band ratios from the study points; 3) The results showed highest correlation coefficient from the band ratio OLI5/OLI4 with an R value of 0.85. The prediction model was then developed by applying regression analysis between the band ratio OLI5/OLI4 and Chl-a concentration of the study points. The reflectance ratios of the validation points were given as input on the prediction model and the model output was considered as predicted Chl-a values of the validation points to check the efficiency of the prediction model. The regression model between laboratory-derived Chl-a value and model-fitted Chl-a value of the validation points revealed a high correlation with an R² value of 0.78. Trophic State Index (TSI) of the lake was also calculated from laboratory-derived Chl-a value and model-fitted Chl-a value of the validation points. The study presented a high correlation of TSI determined from predicted data with TSI from laboratory reference data (R = 0.88). The TSI values of the lake ranged from 65 to 75 which indicate that the lake is appeared to be eutrophic to hypereutrophic conditions. 4) This empirical study showed that Landsat 8 OLI imagery can be effectively applied to estimate Chl-a levels and trophic states for inland lakes.

Treatment techniques for facial paralysis have evolved significantly over the past few decades, offering a variety of options to improve facial symmetry and muscle function. The purpose of this paper is to introduce a novel static treatment technique for the surface of the nasolabial fold (NLF) in patients with chronic facial nerve paralysis, aged between 40 and 80 years, who are not candidates for dynamic rehabilitation and present with NLF erasure. The surgical marking process was initiated by determining the projection of the nasolabial fold on the paralyzed side, through measurement of the NLF on the non-paralyzed side. Subsequently, a line was drawn around the nasal ala, and a second line was demarcated in the medial region of the sulcus. In the region close to the nasal ala, along this second line, a notch was planned. The procedure was conducted under local anesthesia. In this study, four procedures were performed without any complications. Comparatively, the outcomes demonstrated an improvement in facial symmetry, the creation of a new NLF, elevation of the ipsilateral lip commissure, and correction of nasal deviation. The proposed technique is straightforward, reproducible, and can be performed in an outpatient setting.

In this paper is discussed sediment transport as a mechanical process that characterises a natural stream or channel flow regime. The objective of experimental work presented in this paper is to recall and to give another prospect of well-known Meyer-Peter and Müller approach for estimation of Shield’s number (θ_c,θ) in laboratory conditions, and calibration of dimensionless MPM number (A). For this purpose two different experiments are conducted, during the first experiment water amount flushed on the flume and bed slope was changed simultaneously until equilibrium state is achieved, meanwhile is estimated the critical Shield’s number (θ_c). While, during the second experiment, water amount was kept constant, only bed slope of flume was continuously tilted, meanwhile sediment, discharge and Shield’s number (θ) was determined for given hydraulic conditions. In addition calibration of dimensionless MPM number (A) was performed, where several iteration were considered until for (A=3.42), sediment discharge measured become almost equal with sediment discharge computed by using MPM formula. After these experiments, is concluded that MPM formula can be used also for other certain initial condition and similar procedure may be adopted to calibrate the dimensionless MPM number (A) .

Measurements of optical properties have been used for decades to study particle distributions in the ocean. They have been found useful to constrain suspended mass concentration as well as particle-related properties such as size, composition, packing (particle porosity or density) and settling velocity. Optical properties, however, provide measurements that are biased, as certain particles (based on size, composition, shape or packing) contribute to a specific property more than others. Here we study this issue both theoretically as well as by contrasting different optical properties collected simultaneously in a bottom boundary layer, to highlight the utility of such measurements as well as the biases we are likely to encounter using different optical properties to study suspended particles. In particular, we investigate the possibility to infer settling velocity from vertical profiles of optical measurements, finding that the effects of aggregation dynamics can seldom be ignored.

This study examines the absorption and concentration of anthracene (AN) in the garden radish. Studies were conducted to grow radishes from the sowing stage in soil contaminated with AN, and to grow radishes in soil contaminated with AN following maturity (27 days after sowing). For the growth in AN-containing soil from sowing onward, AN levels immediately after seeding ranged from 12,500-36,300 ng/g-ww. AN concentrations during growing period ranged from 7140-16,000 ng/g-ww in soil and from 38.2-2160 ng/g-ww in radish, respectively. For the growth in AN-containing soil after maturity, AN concentrations in soil and radish ranged from 9560-22,100 ng/g-ww and 342-2270 ng/g-ww. The concentrations of AN in the roots and leaves had a higher density than those in the stems. In these experiments, positive relationships between AN levels in soil and radishes were observed. It is inferred that the greater the degree of soil contamination, the greater the effect on the amount of AN assimilated by the radishes. The concentration ratio (radish-to-soil; Cr/Cs) decreased exponentially with days since AN application. This indicates that the concentration ratio is affected by time in contact with AN. According to the results for the change over time of Cr/Cs and contents by radish part, it is thought that AN in the soil has good absorption through the roots to circulate within the organism, and is preferentially distributed and accumulated in the roots and leaves, which have high organic matter content.

Null-flux Electro-dynamic suspension (EDS) system promises to be one of the feasible high-speed maglev systems above 600 km/h. On account of its greater current-carrying capacity, superconducting magnet can provide super-magnetomotive force that is required for null-flux EDS system and cannot be provided by electromagnets and permanent magnets. There is already a relatively mature high-speed maglev technology with low temperature superconducting (LTS) magnets as the core, which works in the liquid helium temperature region (T≤4.2 K). 2-Generation high temperature superconducting (HTS) magnet winded by REBa2Cu3O7−δ (REBCO, RE=rare earth) tapes works above 20 K region and do not need to count on liquid helium which is rare on earth. This paper designed HTS no-insulation closed-loop coils applied for EDS system and energized with persistent current switch. The coils can work at persistent current model and has premier thermal quench self-protection. Besides, a full size double-pancake module was designed and manufactured in this paper, and it was tested in liquid nitrogen. The double-pancake module’s critical current is about 54 A and it is capable of working at persistent current model, whose average decay rate measured in 12 hours is 0.58%/day.

The rates of production of secondary metabolites obtained by employing conventional plant breeding may be low for practical purposes. Thus, innovative approaches for increasing their rates of production are being developed. Here, we propose the use of elicited suspension plant cultured cells (PSCC) with cyclodextrins (CDs) as an alternative method for the production of bioactive compounds from Bryophyllum species. For the purpose, we analyzed the effects of methyl--cyclodextrin and 2-hydroxypropyl--cyclodextrin on cell culture growth and on the intra- and extracellular production of phenols and flavonoids. Results clearly show that CDs enhance the biosynthesis of polyphenols by PSCC favoring their accumulation outside the cells. CDs shift the homeostatic equilibrium by complexing extracellular phenolics, causing stress in cells that respond by increasing the production of intracellular phenolics. We also analyzed the radical scavenging activity of the culture medium extracts against DPPH• radical, which increased with respect to the control samples (no added CDs). Our results suggest that both the increase in the production of polyphenols and their radical scavenging activity are a consequence of their inclusion in the CD cavities. Overall, based on our findings, CDs can be employed as hosts for increasing the production of polyphenols from Bryophyllum species.

This paper presented a two-dimensional, well-balanced hydrodynamic and sediment transport model based on the solutions of variable density shallow water equations (VDSWEs) for sediment-laden flows, and the Exner equation for bed changes. Those equations are solved in a coupled way by the first-order Godunov-type finite volume method. The Harten-Lax-van Leer-Contact (HLLC) Riemann solver is extended to find the local Riemann fluxes in order to maintain the exact balance between the momentum term and the bed slope term. The advantage of a well-balanced scheme over an unbalanced scheme is demonstrated by the synthetic standing contact-discontinuity test case. Then, the model is employed to simulate two laboratory experiments. At last, a field case, the 1996 Lake Ha! Ha! flood event (Canada), is simulated. Results of cross sectional geometries and profiles of longitudinal thalweg agree well with measurements. The accuracy and simplicity of the numerical model, together with the robust implementation, make the model a good candidate for practical engineering applications.

This study presents results of the sediment yield Watershed of Ribeirão do Pinhal, in the city of Limeira, São Paulo, conducted under three different scenarios of the land use: 1 – land use in 2008, 2 – with reforested protection areas, 3 – the increase sugarcane's areas over grassland and citrus areas. The Soil and Water Assessment Tool (SWAT) was used as a hydro-sedimentological modeling tool to simulate these scenarios. This watershed was divided into five sub-watersheds according to the prevalent use, and adjustments were made in soils database parameters and cultures that are in SWAT, to adapt it to the Brazilian reality. Was used climatological data of eight years (2007-2014) for this modeling. Different sediment yield could be noted in the different types of land use, sub-watersheds and scenarios. The uses that presented higher sediment yield, in ascending order, were: natural vegetation, sugarcane, citrus, annual crop e grassland. Sub-watershed number 2 had the highest sediment yield (~10Mg.ha^-1), while the sub-watershed 5, the lowest (5.51Mg.ha^-1). This remained in the three scenarios. Overall, scenario 2 had the lowest sediment yield (7.74Mg.ha^-1). Scenario 1 had 8.37 Mg.ha^-1 and scenario 3, 8.58Mg.ha^-1. SWAT was considered efficient to simulate the sediment yield by scenarios and by use, combining different thematic and tabular data when performing the necessary adjustments on their original database.

This paper evaluates the potential of solar concentration technologies—compound parabolic collector (CPC), linear Fresnel collector (LFC) and parabolic trough collector (PTC)—as an alternative to conventional sources of energy for industrial processes in Latin America, where high levels of solar radiation and isolated areas without energy supply exist. The analysis is addressed from energy, economic and environmental perspective. A specific application for Argentina in which fourteen locations are analyzed is considered. Results show that solar concentration technologies can be an economically and environmentally viable alternative. Levelized cost of energy (LCOE) ranges between 2.5 and 16.9 c€/kWh/m² and greenhouse gas (GHG) emissions avoided range between 33 and 348 kgCO₂/(m²·year). CPC technology stands out as the most recommendable technology when the working fluid temperature ranges from 373K to 423K. As the working fluid temperature increases the differences between the LCOE values of the CPC and LFC technologies decrease. When 523K is reached LFC technology is the one which presents the lowest LCOE values for all analyzed sites, while the LCOE values of PTC technology are close to CPC technology values. Results show that solar concentration technologies have reached economic and environmental competitiveness levels under certain scenarios, mainly linked to solar resource available, thermal level requirements and solar technology cost.

Soils provide important regulating ecosystem services and have crucial implications for human well-being and environmental conservation. However, soil degradation and particularly soil erosion jeopardize the maintenance and existence of these services. This study explores the spatio-temporal relationships of soil erosion to understand the distribution patterns of sediment retention services in mainland Portugal. Based on Corine Land Cover maps from 1990 to 2018, the InVEST Sediment Delivery Ratio (SDR) model was used to evaluate the influence of sediment dynamics for soil and water conservation. Spatial differences in the sediment retention levels were observed within the NUTS III boundaries, showing which areas are more vulnerable to soil erosion processes. Results indicated that the Region of Leiria, Douro and the coastal regions have decreased importantly sediment retention capacity over the years. However, in most of the territory (77.52%) changes in sediment retention were little or not important (i.e., less than 5%). The statistical validation of the model proved the consistency of the results, highlighting the usefulness of this methodology to analyse the state of soil erosion in the country. These findings can be relevant to support strategies for more efficient land use planning regarding soil erosion mitigation practices.

Due to the nonlinear stiffness and fractional-order damping characteristics of some real suspension systems, coupled with the presence of viscoelastic materials, fractional-order nonlinear suspension system modeling has become a focus of research in recent years. In this study, an electric oil and gas actuator based on fractional-order PID position feedback control is proposed, through which the damping coefficient of the suspension system is adjusted to realize the active control of the suspension. A fractional order PID algorithm is used to control the motor's rotational angle to realize the damping adjustment of the suspension system. In this process, the road roughness is collected by the sensors as the criterion of damping adjustment, and the particle swarm algorithm is utilized to find the optimal objective function under different road surface slopes, to obtain the optimal cornering value. According to the mathematical and physical model of the suspension system, the simulation model and the corresponding test platform of this type of suspension system are built. The simulation and experimental results show that the simulation results of the fractional-order nonlinear suspension model are closer to the actual experimental values than those of the traditional linear suspension model, and the accuracy of each performance index is improved by more than 18.5%. The designed active suspension system optimizes the body acceleration, suspension dynamic deflection, and tire dynamic load to 89.8%, 56.7%, and 73.4% of the passive suspension, respectively. Notably, the designed fractional order PID control circuit for the motor shows better control results compared to the conventional PID control circuit. This study provides an effective theoretical and empirical basis for the control and optimization of fractional-order nonlinear suspension systems.

Background: It is known that Preeclampsia affects the lactogenesis. However, data on effects of this pathology on the human milk neurobiomarkers composition are not available. The aim of this study is to investigate the effects of this gestational pathology on Activin A levels, a neurobi-omarker known to play an important role in the development and protection of the central nerv-ous system. Methods: The women recruited were divided in two different study groups: preeclamptic or normotensive women. All the human milk samples were collected using the same procedure. Activin A was quantified using an ELISA test. To investigate the effect of Preeclampsia on the Activin A concentration in the 3 lactation phases, mixed linear model with unistructural covariance structure, mother as random effect, and fixed effects were performed. Results: Activin A was detected in all samples. There were no significant differences between Preeclamptic and Normotensive women. The only significant effect is related to the lactation phase: it is significant the difference between colostrum and mature milk (p<0.01). In conclusion these results allow us to affirm that breast milk beneficial properties are maintained even if preeclampsia occurs.

This study is part of a project designed to simulate the long-term landform equilibrium of a rehabilitated mine site. The project utilizes event fine suspended sediment (FSS) fluxes in a receiving stream following a rainfall event as an indicator of landform stability. The aim of this study was to use HEC-HMS to determine sediment and discharge quantity upstream to determine how it affects the downstream development of the catchment landform, in terms of sediment changes and geomorphology. Thus, the study focused on hydrology and sediment modelling of the upper catchment with HEC-HMS (Hydrologic Engineering Center-Hydrologic Modeling System) to determine daily discharge and sediment output at the catchment outlet. HEC-HMS was used to calibrate the stream discharge and FSS quantities at the catchment outlet to observed continuous discharge and FSS values. Calibration of the HEC-HMS model was done for two water years and then the same model parameters were used to validate the model for a third water year. Catchment discharge and FSS were calibrated and validated for continuous rainfall events against observed discharge and FSS data at the catchment outlet. The model was then run for a projected rainfall of 50 years. The denudation rate predicted by the model falls in the range previously determined for the region. The simulated sediment output was compared to the rainfall trends over the years. As a result, the sediment spikes following a rainfall-runoff event gradually decreased over time. Reducing FSS spikes indicate that the landform gradually attains stability. This modeling study can be used for long-term simulations to determine erosion equilibrium over the years and to quantify sediment yield in catchments for projected wet and dry rainfall scenarios.

Eysenhardtia platycarpa (Fabaceae) is a medicinal plant used in México and it lacks biotechnological studies for its use. The aim of this work was to establish a cell suspension cultures (CSC) of E. platycarpa, determine the phytochemical profile, and evaluate its antifungal activity. Friable callus and CSC were established with 2 mg/L 1-naphthaleneacetic acid plus 0.1 mg/L kinetin. The highest total phenolics of CSC was 15.6 mg GAE/g dry weight and the total flavonoids content ranged from 56.2 to 104.1 µg QE/g dry weight. CG‒MS analysis showed that the dichloromethane extracts of CSC, sapwood and heartwood have a high amount of hexadecanoic acid (22.3 ‒ 35.3 %) and steroids (13.5 ‒ 14.7%). Heartwood and sapwood defatted hexane extracts have the highest amount of stigmasterol (≈ 23.4%) and β-sitosterol (≈ 43%), and leaf extracts presented β-amyrin (16.3%). Methanolic leaves extracts showed mostly sugars and some polyols, mainly D-pinitol (74.3%). Dichloromethane and fatty hexane extracts of CSC exhibited the percentages inhibition higher for Sclerotium cepivorum with 71.5 and 62.0%, respectively. The maximum inhibition for Rhizoctonia solani was with fatty hexane extracts of the sapwood (51.4%). Our study suggest that CSC extracts could be used as a possible complementary alternative to synthetic fungicides.

The objective of the research was to evaluate the concentration of organochlorine pesticides in sediment of the Alvarado Veracruz lagoon system, Mexico. To define the risk that causes to the public health the consumption of organisms that inhabit in sediments of this ecosystem. In 20 out of 41 stations analyzed, 11 prohibited organochlorine pesticides were identified, such as hexachlorocyclohexane, lindane, aldrin, dieldrin, endrin, among others. The highest concentrations were: aldrin 46.05; β-HCH 42.11; α-HCH 38.44; γ-HCH (lindane) 34.20; δ-HCH 31.61; methoxychlor 29.40; heptachlor epoxide 25.70; heptachlor 24.11; dieldrin 22.13; endrin 21.23; and endrin aldehyde 12.40 ng g-1. Concentrations reported are prohibited in international standards. In Mexico it is necessary to establish permissible limits in the environmental legislation for this matrix. There is a strong need to demonstrate, with scientific studies, the level of concentration reported by impact of compounds widely used in agricultural-livestock activities.

Background: Physical activity has been considered as a promising approach to slow down the disease process in Multiple Sclerosis (MS) patients. While the functional impairments of MS have been studied in detail, but there is limited evidence of the efficacy of exercise interventions on the Multiple Sclerosis functional composite (MSFC) score in these patients. The study aim was to in-vestigate the improvement in MSFC score by multi-function swing suspension training (MFSST) in the women with MS. Methods: The patients were divided into the intervention and control groups. A total of 47 MS patients completed the MSFC components at baseline and after the intervention. Z scores were created for each test based on control means. Results: The MSFC components showed a significant increment in comparison with the baseline levels in the four, six, and eight weeks following the first exercise session (all p<0.05). These dif-ferences in the control group were not significant. The improvement in the MSFC score and the component Z-scores in the intervention groups was found from the fourth week onwards. Conclusions: The study findings highlight that MFSST can be used as an effective treatment method in MS patients due to its positive effects on physical parameters, such as muscles strength, functional impairments, and cognitive problems.

The determination of the non-loading condition of the rail cable shifting (RCS) system, which consists of main cables, hangers and rail cables, is the premise of the girder erection for the long-span suspension bridges. An analytical form-finding analysis model of shifting system is established according to the basic assumptions of flexible cable structures. Herein, the rail cable is discretized into segmental linear cable elements and the main cable is discretized into segmental catenary elements. Moreover, the calculation and analysis equation of each member and their iterative solutions are derived by taking the elastic elongation of the sling into account. In addition, by taking the girder construction of Aizhai suspension bridge as engineering background, a global scale model of the RCS system is designed and manufactured; also the test system and working conditions are established. The comparison between the test results and analytical results shows the presented analytical method is correct and effective. The process is simplified in the analytical method, and the computational results and precision can satisfy the practical engineering requirements. In addition, the proposed method is suitable to apply to the computation analysis of similar structures.

As a model for economic and ecological systems, replicator dynamics represents a basic form of agent competition for finite resources. Here, we investigate the effects of stochastic resetting in this kind of processes. Random reset events abruptly lead individual resources to a small value from which dynamics must start anew. Numerical results show that resource distribution over the population of competing agents develops highly nonuniform profiles, exhibiting clustering and fluctuations with anomalous dependence on the population size. This non-standard statistical behavior jeopardizes an analytical treatment based on mean-field assumptions. We propose alternative simplified analytical approaches which provide a stylized description of entropy evolution for the clustered distribution of resources and explain the unusually slow decrease of fluctuations.

To achieve efficient utilization of low-concentration mine gas, reduce resource waste, and alleviate environmental pollution, high-temperature oxidation of low-concentration gas at a concentration range of 1.00% to 1.50% that is directly discharged into the atmosphere during coal mine production was oxidized to recover heat for reuse. The gas oxidation equipment was improved for the heating process, and the safety of low-concentration gas oxidation under high-temperature environment was evaluated. Experimental results showed that the reactor could provide a 1000 ℃ high-temperature oxidation environment for gas oxidation after installing high-temperature resistant ceramics. The pressure variation curves of the reactor with air and different concentrations of gas were similar. Due to the thermal expansion, the air pressure slightly increased and then returned to normal pressure. In contrast, the low-concentration gas exhibited a stable pressure response in the high-temperature environment of 1000 ℃. The outlet pressure was significantly greater than the inlet pressure, and the pressure difference between the inlet and outlet exhibited a trend to increase with the gas concentration. The explosion limit varied with the temperature and the blend with oxidation products. The ratio of measured gas pressure to air pressure after oxidation was below the explosion criterion, indicating that the measured concentration gas is still safe after the shift of explosion limit, which provides a safe concentration range for efficient use of low-concentration gas in the future.

The Rupat Strait, a part of the Malacca Strait, is recognized as semi-closed waters and shows a high activity; thus, discovering the transport sediment mechanism of the strait as a consequence of ambient and anthropogenic forces is essential. Hydrodynamic and sediment transport modelling was constructed using the 2-Dimensional Explicit method which is averaged over depth. The results show that the dispersion of sediment at high tide is longer than that at low tide. This follows the hydrodynamic model in which current velocity at high tide is greater than the ocean current at the low tide. The previous sediment observation supports the results of transport sediment modelling, indicating that the anthropogenic factors are highly associated with the sedimentation in the Rupat strait

Reservoirs are characterized by accumulation of sediments where micropollutants may concentrate, with potential toxic effects on downstream river ecosystems. However, sediment management such as flushing is needed to maintain storage capacity. Climate change is expected to increase sediment loads, but potential effects on their quality are scarcely known. In this context, sediment contamination by trace elements (As, Cd, Cr, Cu, Hg, Ni, Pb, Zn) and organics (PAHs, PCBs, C>12) was analyzed in 20 reservoirs located in Italian Central Alps. A strong As and a moderate Cd, Hg and Pb enrichment was emphasized by Igeo, with potential ecotoxicological risk according to PEC quotients. Siltation, granulometry, total organic carbon (TOC) and altitude resulted as the main drivers governing pollutant concentrations in sediments. According to climate change models, expected increase of rainfall erosivity will enhance soil erosion and consequently the sediment flow to reservoirs, potentially increasing coarse grain fractions and thus potentially diluting pollutants. Conversely, increased weathering may enhance metal fluxes to reservoirs. Increased vegetation cover will potentially result in higher TOC concentrations, which may contrast contaminant bioavailability and thus toxicity. Our results may provide elements for a proper management of contaminated sediments in a climate change scenario aiming at preserving water quality and ecosystem functioning.

The dynamics of suspended sediment involves inherent non-linearity and complexity as a result of the presence of both spatial variability of the basin characteristics and temporal climatic patterns. As a result of this complexity, the conventional sediment rating curve (SRC) and other empirical methods produce inaccurate predictions. Deep neural networks (DNNs) have emerged as one of the advanced modeling techniques capable of addressing inherent non-linearity in hydrological processes over the last few decades. DNN algorithms are used to perform predictive analysis and investigate the interdependencies among the most pivotal water quantity and quality parameters i.e., discharge, suspended sediment concentration (SSC), and turbidity. In this study, the Long short-term memory (LSTM) algorithm of DNNs is used to model the discharge-suspended sediment relationship for the Stony Clove Creek. The simulations were run using primary data on discharge, SSC and turbidity. For the development of the DNN models and examining the effects of input vectors, combinations of different input vectors (namely discharge, and SSC) for the current and previous days are considered. Furthermore, a suitable modelling approach with an appropriate model input structure is suggested based on model performance indices for the training and testing phases. The performance of developed models is assessed using statistical indices such as root mean square error (RMSE), mean absolute error (MAE), and coefficient of determination (R2). Statistically, the performance of DNN-based models in simulating the daily SSC performed well with observed sediment concentration series data. The study demonstrates the suitability of the DNN approach for simulation and estimation of daily SSC, opening up new research avenues for applying hybrid soft computing models in hydrology.

Sediment transport is highly sensitive to flow conditions, showing significant increase during flood events. Based on this principle, this study set out to rank flood events occurring along river Trotuș (Romania) based on the amount of transported sediment and event duration. The 77 flood events recorded from 2000 to 2017 were ranked into 4 classes: type A (4%); type B (16%), type C (14%) and type D (66%). The sediment transport specific for the 4 types of flood events was related to the flow discharge (sediment rating curve and hysteresis effect), the specific stream power and the energy expenditure of these events. More than 60% of the hysteresis loops typical for flood events were clockwise, thus singling out the channel as the main sediment source. Ca. 74% of the total sediment yield was transported at stream power values higher than the 300 Wm-2 threshold, which was exceeded in less than 1% of the investigated timeframe. The changes occurring in the sediment transport rates after major floods show that these events are significant thresholds in the hydrogeomorphic evolution of river channels.

Molecular and morphological properties of poly(vinyl chloride) grains produced by suspension polymerization of VCM in the presence of a mixture of three kind of initiators (i.e. fast, mild and slow) (named as Cok process) was experimentally investigated in a pilot-scale reactor. The results obtained here were initially compared with a isothermal regular process (named as control process) and then with those obtained already for other productivity-enhancing polymerization techniques (i.e. nonisothermal and fast initiator dosage process). The results showed that, in contrast to nonisothermal and fast initiator dosage process, the addition of initators mixture at the beginning of the reaction has the smallest influence on molecular weight and polydispersity index compared to control process. It is obvioused that Cok-PVC grains have the lowest cold plasticizer absorption and porosity among these mentioned processes. Scanning electron microscopy (SEM) showed that the particles produced by Cok process are more regularly shaped, with a smoother surface compared with the control product. According to the literatures, all three productivity-enhancing techniques lead to an apparent quality enhancement, higher flowability and greater bulk density of final grains. While both processes of continous initiator dosage and nonisothermal polymerization broaden the particle size distribution of final PVC grains, applying initiator mixture produces particles with the same particle size distribution as control process. The SEM images processing showed that Cok process deccelerates the formation of a three-dimensional skeleton of primary particles relative to the control polymerization. In comparison with nonisothermal trajectory and continous fast initiator dosage system, the Cok polymerization process leads to the most delay of motionless conversions and fusion time as well.

The impact of ponds on basins has recently started to receive its well–deserved scientific attention. In this study, pond–induced impacts on soil erosion and sediment transport were investigated at the scale of the French Claise basin. In order to determine erosion and sediment transport patterns under current conditions, the CORINE erosion and SWAT models were used. The impact of ponds on the studied processes was revealed by means of land cover change scenarios, using ponded versus pondless inputs. Results show that under current conditions (pond presence), 12.48% of the basin corresponds to no–erosion risk zones (attributed to the dense pond network), while 65.66% corresponds to low–erosion risk, 21.68% to moderate–erosion risk and only 0.18% to high–erosion risk zones. The SWAT model revealed that ponded sub–basins correspond to low sediment yields areas, in contrast to the pondless sub–basins, which yield appreciably higher erosion rates. Under the alternative scenario, erosion risks shifted to 1.12%, 0.52%, 76.8% and 21.56% for no, low, moderate and high–erosion risks, respectively, while the sediment transport pattern of the Claise completely shifted to higher sediment yield zones. This approach solidifies ponds as powerful man–induced modifications to hydro/sedimentary processes.

Lake Rawa Besar is an urban lake surrounded by dense settlements and market area. Currently Lake Rawa Besar is experiencing physical and ecology strain. This research’s objectives are to determine the levels of sediment and nutrient, the distribution, also the relation to land use and human activities producing pollutant. Field surveys with 30 sample points and observations was needed scattered within the lake. Measuring the value of each parameter is carried out in national standardized laboratory. The result shows that sediment load of TDS is still below the standard limit for clean water, while TSS levels in the middle of lake exceed the standard limit. Nutrient loads, spesifically nitrate and phospate levels is below the standard limit. While turbidity and BOD levels have a uniform distribution pattern in the lake, exceed the standard limit for clean water, and have a positive correlation. High levels of turbidity and BOD are caused by household waste and human activities producing organic waste such as tofu factory, fowl manure, and garbage dump. Small sewage goes into the lake mediates pollutants inflow. Attention is needed by nearby people, also for the government, to sustain the ecological condition of the lake.

This paper uses polypropylene (PP) as the matrix and acrylic acid (AA) and maleic anhydride (MAH) as functional monomers to prepare PP-g-(AA-MAH) fibers by suspension grafting and melt-blown spinning technology that are easy to industrially scale-up. The fibers can be used to adsorb aniline from wastewaters. Results showed that the grafting ratio reached the maximum of 12.47%. The corresponding optimal conditions were grafting time of 3h, AA : MAH = 0.75, total monomer content of 55%, benzoyl peroxide 1.4%, xylene concentration of 6 mL/g PP, and deionized water content of 8 mL/g PP. Owing to its good fluidity and thermal stability, the product of suspension grafting can be used for melt-blown spinning. Infrared spectroscopic and nuclear magnetic resonance spectroscopic analyses indicated that AA and MAH were successfully grafted onto PP fibers. After grafting, the hydrophilicity of PP-g-(AA-MAH) fiber increased. Therefore, it had higher adsorptivity for aniline and the adsorption capacity could reach 42.2 mg/g at 45 min. Moreover, the PP-g-(AA-MAH) fibers showed good regeneration performance.

Shrubs are a significant component of urban vegetation residing in parks, but they experience various influences of biotic and abiotic agents, among which aphids play an important role. In this work, the effect of aphid colonization on three shrub species in urban environment was examined. Fourteen parameters have been analyzed, describing photosynthetic pigment content and gas exchange to carbon, nitrogen, and hydrogen partition. While no significant effect of colonization was found on photosynthetic pigment parameters, the effect was significant on gas exchange parameters. The strongest effect aphid colonization achieved on nitrogen partition and C/N ratio, parameters that could be suggested in further similar studies. All parameters were classified in two groups according to principal component analysis, suggesting correlation between nitrogen and carbon content, C/N ratio, measured gas exchange parameters and chlorophyll a content. The ratio between net photosynthesis and dark respiration (A/K) was in the second group, suggesting that this parameter provide additional information on the effect of aphid colonization, and deserve special attention in further studies. There were differences in reaction of examined shrub species, where the strongest reaction by gross primary productivity (GPP) achieved Hybiscus syriacus, and by nitrogen partition and C/N ratio Spirea trilobata and Cydonia japonica.

Beer fermentation is typically monitored by periodic sampling and off-line analysis. In-line sensors would remove the need for time-consuming manual operation and provide real-time evaluation of the fermenting media. This work uses a low-cost ultrasonic sensor combined with machine learning to predict the alcohol concentration during beer fermentation. The highest accuracy model (R2=0.952, MAE=0.265, MSE=0.136) used a transmission-based ultrasonic sensing technique along with the measured temperature. However, the second most accurate model (R2=0.948, MAE=0.283, MSE=0.146) used a reflection-based technique without the temperature. Both the reflection-based technique and the omission of the temperature data are novel to this research and demonstrate the potential for a non-invasive sensor to monitor beer fermentation.

The mass concentration of particulate matter (PM) has been systematically used in epidemiological studies as exposure indicator, to relate airborne concentrations with a wide variety of human health effects, which can be hardly explained by using this single parameter. In fact, PM is a “particle cocktail” that includes a complex mixture of compounds with a wide range of sizes, chemical compositions and emission sources. Current research hypothesizes that many of the adverse health effects are derived from oxidative stress in biological systems caused by the deposition of PM into the lungs. This emerging hypothesis is called the oxidative stress paradigm. In this commentary article we analize how this new paradigm could help to answer the as-of-yet unanswered questions related to the mechanism of action of PM pollution on human health. Acellular oxidative potential (OP) assays have been emerged as a promising approach to quantify the PM potential to induce oxidative stress and to relate it with the chemical composition and size distribution of PM. Recent researches have shown that the OP is related to the presence of metals, organic carbon, polyaromatic hydrocarbons and quinones. However, the association between PM and particle-induced toxicity is still largely unknown. Therefore, additional research is needed to identify the specific PM characteristic(s), such as its specific size, emission source or chemical content, which contribute the most to its redox activity. Thus, the OP measurements provide information that allows us to evaluate and integrate the toxic potential of PM in a unique parameter, whose relationships with emission sources, size distribution and/or chemical composition should be faced in the near future.

For the purpose of clean energy hydropower development, the construction of reservoirs has been continuously promoted in the Jinsha River basin for many years, and how the reservoirs affect the water and sediment process is a very necessary topic to study. This study is based on the gauged water and sediment data (span from the 1960’s to 2020) at Shigu, Panzhihua, and Xiangjiaba stations downstream located in the trunk channel of the river, and uses Mann-Kendall trend test method and double cumulative curve method to comprehensively judge the variation trends of runoff and suspended sediment load and reveal their credible mutation years. The linear regression method is used to reveal the variation characteristics of the relationship between water and sediment before and after the abrupt change years. The results show that the variations in runoff at Shigu and Panzhihua stations have significant and relatively obvious increasing trends, respectively, and that at Panzhihua station has a mutation year of 1985. The runoff at Xiangjiaba Station slightly increased but not significantly. The variation of suspended sediment load showed a temporal and spatial differentiation. The variation of sediment discharge at Shigu Station showed an increasing trend with a mutation year of 1997. For Panzhihua Station, it showed an increasing trend before 1998, but has significantly decreased since 1998. The fluctuation of sediment transport at Xiangjiaba Station was significant before 1998, but the trend is unclear. In the period of 1998−2020, it showed a significant decreasing trend, especially since 2013, when the mean annual suspended sediment load only accounted for 0.61% of its multi-year average. The variations of mean annual sediment concentration and sediment inflow coefficient at the hydrological stations is consistent with the variation trend of sediment transport. Before 2013, the correlation between water and sediment was strong, but thereafter it was extremely weak. The two sudden years of 1998 and 2013 are consistent with the year when large reservoirs were built in the river basin. The construction of large reservoirs and their large amount of sediment retention are the key reasons for the sudden changes in the water-sediment relationship and the sharp decrease in sediment transport in the downstream reach of the reservoir dam. The climate and underlying surface changes in the study area are not significant, and their impact on the water and sediment processes in the watershed is limited.

This paper introduces a three-layer system, proposing a comprehensive model of granular mixture transport over a mobile sloped bed in a steady flow. This system, consisting of the bottom, contact and upper zones, provides complete, continuous sediment velocity and concentration vertical profiles. The model considers gravity’s effect on sediment transport in the bottom (dense) layer, a crucial factor often overlooked in previous studies. The induced movement in the mobile sublayer of the dense layer causes an increase in velocity at the upper boundary of this layer, significantly affecting the vertical distributions of velocity and concentration above this layer. We described the interactions between fractions and an intensive sediment mixing and sorting process in the contact layer. The proposed shear variation, with an increase in its maximum value at the bed, adds to the novelty of our approach. The data sets used for the model’s validation cover various conditions, including slopes, grain diameters, densities and grain mobility conditions, from incipient motion to a fully mobilised bed. This extensive validation process instils confidence in the theoretical description and its applicability to real-world scenarios.

A three-dimensional, unstructured grid, hydrodynamic and suspended-sediment transport model (i.e., SELFE-SED) was developed to simulate temporal and spatial variations of suspended sediment and was applied to the subtropical subalpine Tsuei-Feng Lake (TFL) of Taiwan. The model was validated with measured water level and suspended‑sediment concentration in 2009, 2010, and 2011. The overall model simulation results are in quantitative agreement with the observational data. The validated model was then applied to explore the most important parameter that affects the suspended-sediment concentration and to investigate the effect of wind stress on the mean current and suspended‑sediment distribution in this shallow lake. Modeling results of sensitivity analysis reveal that the settling velocity is a crucial parameter and erosion rate is less important in the suspended-sediment transport model. Remarkable lake circulation was found based on the strength of wind speed and wind direction. Strong wind would result in higher mean current in the top layer and suspended-sediment distribution in the top and bottom layers. This study demonstrated that the wind stress played a significant influence on mean circulation and suspended-sediment transport in a shallow lake.

When the epipelic algae group growing on the concrete inclined side wall, which is typical of urban rivers and open diversion channels, enters the water flow, it will seriously affect the func-tion of the rivers or the channels. It is urgent to predict the transport capacity of epipelic algae group with water flow. However, the current research on the transport of pollutants is mostly based on mathematical models, and the study of the transport of flake epipelic algae group is extremely rare. A generalized hydrodynamic experimental model of a flume with sidewall epi-pelic algae group was established. Through a series of hydraulic experiments, the physical movement form and transport capacity of the suspended epipelic algae group on the side wall of the channel were studied qualitatively and quantitatively by taking the thickness, sheet size and flow rate of the epipelic algae group as the influencing factors. The key influencing factors of the suspension of epipelic algae are clarified, so as to quantitatively analyze the critical conditions of its suspension. Through flow scheduling, the probability of epipelic algae gathering some-where is increased. It provides a theoretical basis for realizing the long-distance migration of epipelic algae and optimizing the mathematical model.

Adult stem cells (ASCs) can be cultured with difficulty from most tissues, often requiring chemical or transgenic modification to achieve adequate quantities. We show here that mouse primary fibroblasts grown in suspension change from the elongated and flattened morphology observed under standard adherent culture conditions generating rounded cells with large nuclei and scant cytoplasm expressing the mesenchymal stem cell (MSC) marker (Sca1; Ly6A) within 24hrs. Based on this initial observation, we describe here a suspension culture method that, irrespective of the lineage used, mouse fibroblast, primary human somatic cells (fibroblasts, hepatocytes and keratinocytes), is capable of generating a high yield of cells in spheroid form which display expression of ASCs surface markers, circumventing the anoikis which often occurs at this stage. Moreover, mouse fibroblasts-derived spheroids can be differentiated into adipogenic and osteogenic lineages. Analysis of single cell RNA sequence data identified 8 distinct cell clusters with one in particular comprising approximately 10% of the cells showing high levels of proliferative capacity expressing high levels of genes related to MSCs and self-renewal as well as extracellular matrix (ECM). We believe the rapid, high-yield generation of proliferative, multi-potent ASC-like cells by the process we term suspension-induced stem cell transition (SIST) could have significant implications for regenerative medicine.

Retinal lipofuscin accumulates with age in the retinal pigment epithelium (RPE) where its fluorescence properties are used to assess the retinal health. It was observed that there is a decrease in lipofuscin fluorescence above the age of 75 years and in early stages of age-related macular degeneration (AMD). The purpose of this study was to investigate the response of lipofuscin isolated from human RPE, and lipofuscin-laden-cells to visible light, and determine whether an abundant component of lipofuscin, docosahexaenoate (DHA) can contribute to lipofuscin fluorescence upon oxidation. Exposure of lipofuscin to visible leads to a decrease of its long-wavelength fluorescence at about 610 nm with concomitant growth of the short-wavelength fluorescence. The emission spectrum of photodegraded lipofuscin exhibits similarity with that of oxidized DHA. Exposure to light of lipofuscin-laden cells leads to loss of lipofuscin granules from cells, while retaining cell viability. The spectral changes of fluorescence in lipofuscin-laden cells resemble those seen during photodegradation of isolated lipofuscin. Our results demonstrate that fluorescence emission spectra together with quantitation of intensity of long-wavelength fluorescence can serve as a marker useful for lipofuscin quantification and for monitoring its oxidation, thereby useful for screening the retina for increased oxidative damage and early AMD-related changes.

Silybum marianum (L.) Gaertn is a rich source of antioxidants and anti-inflammatory flavonolignans with great potential for use in pharmaceutical and cosmetic products. Its biotechnological production using in vitro culture system has been proposed. Chitosan is a well-known elicitor that strongly affects both secondary metabolites and biomass production by plants. The effect of chitosan on S. marianum cell suspension is not known yet. In the present study, suspension cultures of S marianum were exploited for their in vitro potency to produce bioactive flavonolignans in the presence of chitosan. Established cell suspension culture was maintained on the same hormonal media supplemented with 0.5 mg/L BAP (6-benzylaminopurine) and 1.0 mg/L NAA (α-naphthalene acetic acid) under photoperiod 16/8 h (light/dark) and exposed to various treatments of chitosan (ranging from 0.5 to 50.0 mg/L). The highest biomass production was observed for cell suspension treated with 5.0 mg/L chitosan, resulting in 123.3 g/L fresh weight (FW) and 17.7 g/L dry weight (DW) productions. Chitosan treatment resulted in an overall increase in the accumulation of flavonoids, phenolic compounds and silymarin. High accumulation levels of silybin B, silydianin and silybin A were recorded by HPLC analysis. The corresponding extracts displayed interesting antioxidant and anti-inflammatory capacities. In particular, high ABTS antioxidant activity (741.5 μM Trolox C equivalent antioxidant capacity) was recorded in extracts obtained in presence of 0.5 mg/L of chitosan. On the opposite, highest inhibitions of cyclooxygenase 2 (COX-2, 30.5 %), secretory phospholipase A2 (sPLA2, 33.9 %) and 15-lipoxygenase (15-LOX-2, 31.6 %) enzymes involved in inflammation process were measured in extracts obtained in presence of 5.0 mg/L of chitosan. Taken together, these results highlight the high potential of the chitosan elicitation of the S. marianum cell suspension for enhanced production of antioxidant and anti-inflammatory silymarin-rich extracts.

Microplastics are a fast emerging group of contaminants. Their worldwide occurrence in water, sediment, and aquatic fauna raises questions and concerns as to their probable effects on aquatic life and ecology. This study investigates for the first time presence, abundance, and types of microplastics in water and sediment from a lagoon bordering the large urban agglomeration of Lagos in Nigeria, and renders additional information about grain size and sediment composition. Water and sediment samples were collected from four locations in the Lagos lagoon and a tributary. The abundance and distribution of microplastics in four range classes were determined for the sampled locations. Plastic particles were counted using digital microscopy, and identified with FTIR and pyrolysis GC-MS. The abundance of microplastics ranged from 310-2319 microplastic particles/kg in sediment, and 139-303 particles/m³ in water. The large discrepancy in the sediments can be explained by sediment characteristics as more microplastics were detected in the fine-grained sediments of Makoko. Fibres were the predominant shape found in all samples followed by fragments and few films whereas spheres were missing. Fibres were more abundant in water (92.6 %) than in sediments (32.5 %) while more fragments and foils occurred in sediments. The most commonly used polymers polypropylene and polyethylene were also the most detected ones in both matrices. Compared to other studies in Nigeria, our findings especially in the coarser sediments were lower while the fine-grained site revealed similar results.

Densimetric Froude (Fr) is the minimum velocity required to prevent sediment deposition in pipes. Prediction of Fr is of utmost importance in numerous applications in civil engineering. In this paper through using a new hybrid method. Genetic Algorithm (GA) is used for optimum selection of membership functions of Adaptive Neuro-Fuzzy Inference System (ANFIS), and Singular Value Decomposition (SVD) method is used to compute the linear parameters of ANFIS’s results section (ANFIS-GA/SVD). Also, two different target functions are known as training error (TE) and prediction error (PE) by Pareto curve, the trade-off between these functions is selected as the optimal modeling point. First, different models will be presented using the parameters affecting Fr prediction, classifying them in different groups; then the Fr parameter will be predicted for all the different models through utilizing three different sets of data and the ANFIS-GA/SVD technique. The results of the models indicate that the best Fr prediction is obtained when independent parameters such as volumetric sediment concentration (CV), ratio of median diameter of particle size to pipe diameter (d/D), ratio of median diameter of particle size to hydraulic radius (d/R) and overall friction factor of sediment (λs) use as input variables in prediction of Fr. A sensitivity analysis is also conducted for the purpose of examining the effect of each of the dimensionless parameters on Fr prediction accuracy. Comparing the results of the suggested models with the existing regression-based equations shows that ANFIS-GA/SVD (R²=0.986, MAPE=4.397, RMSE=0.206, SI=0.053, ρ=0.026, BIAS=-0.025) is more accurate than the rest of the models.

Many species of the Asteraceae family are used in traditional Mexican medicine for possessing healing properties. Ageratina pichinchensis (Asteraceae) is a plant used for the treatment of gastric ulcers, deep wounds and for its antifungal effects. The aim of this study was to establish a cell suspension culture of A. pichinchensis, quantify the anti-inflammatory constituents 2,3-dihydrobenzofuran and 3-epilupeol, to evaluate the anti-inflammatory potential of its extracts and perform a phytochemical analysis. Cell suspension cultures were established in MS culture medium supplemented with 30 g L-1 sucrose and 1.0 g L-1 α-naphthaleneacetic acid (NAA) plus 0.1 mg L-1 6-furfurylaminopurine (KIN). The ethyl acetate extracts of cell suspension cultures analyzed by GC revealed that the maximum production of compounds The anti-inflammatory activity of these extracts exhibited significant inhibition of NO production. Furthermore, the phytochemical study of EtOAc and MeOH extracts of the biomass on day 20 led to the identification of 17 known compounds. The structures of compounds were assigned by analysis of 1D and 2D NMR data and the remainder by GC-MS. This is the first report of the production of the (-)-Artemesinol, (-)-Artemesinol glucoside, Encecalin and 3,5-diprenyl-acetophenone compounds by a cell suspension cultures of A. pichinchensis.

Spider silk has excellent strength and elasticity in natural, researchers have been working for decades try to achieve natural spider silk outstanding mechanical properties using recombinant spider silk protein (spidroin) through artificial spinning. In this work, we chose wet spinning method to explore the relationship between concentration of coagulation bath and fiber performance. It was found that the concentration of methanol has important effect on fiber continuity, diameter and mechanical properties. Lower concentration favors spinning continuous thinner, fibers with high strain. Secondary stretching benefits spinning silk fibers with stable mechanical properties, and thermal stability. Through applying different methanol concentration and additional stretching, we obtained silk fibers with Young’s modulus of 3.052± 2.626 GPa, stress of 25.3944 ± 17.48 MPa, and strain of 140 ± 95.4%.

The concentration of cerebrospinal fluid total protein (CSF-TP) is important for the diagnosis of neurological emergencies. Recently, some Western studies have shown that the current upper reference limit of CSF-TP is quite low for older patients. However, little is reported about the concentration of CSF-TP in older Asian population. In this study, we retrospectively analyzed the CSF-TP concentrations in Japanese healthy older volunteers. CSF samples in 69 healthy Japanese volunteers (age range: 55–73 years) were collected by lumbar puncture, and the data of CSF were retrospectively analyzed. The mean (standard deviation) CSF-TP was 41.7 (12.3) mg/dL. The older group (≥ 65 years old) had higher CSF-TP concentration than the younger group (55–64 years old). The 2.5th percentile and 97.5th percentile of CSF-TP were estimated as 22.5 and 73.2 mg/dL, respectively, which were higher than the current reference range in Japan (10–40 mg/dL).

MEMThe PdNi film hydrogen sensors with Wheatstone bridge structure were designed and fabricated by the micro-electro-mechanical system (MEMS) technology. The integrated sensors consisted of four PdNi alloy film resistors. The interval two of them were shielded with silicon nitride film and used as reference resistance, while the others were used for hydrogen sensing. The PdNi alloy films and SiN films were deposited by magnetron sputtering. The morphology and microstructure of the PdNi films were characterized with X-ray diffraction (XRD). The output resistance signal was converted to millivolt output voltage signal for easy data acquisition. Hydrogen (H2) sensing properties of PdNi film hydrogen sensor with Wheatstone bridge structure was investigated under different temperatures (30℃, 50℃ and 70℃) and H2 concentrations (from 10 ppm to 0.4%). The hydrogen sensor demonstrated good response at different hydrogen concentrations and high repeatability in cycle testing under 0.4% H2 concentration. Under 10ppm hydrogen, the PdNi film hydrogen sensor had evident and collectable output voltage of 600 μV.

The kinetics and efficacy profiles of photoinitiated polymerization are theoretically presented. For the same dose, lower light intensity achieves a higher steady-state-efficacy (SSE) in type-I; in contrast, type-II has an equal SSE. Higher light intensity has a faster rising efficacy, due to faster depletion of photoinitiator (PS) concentration. However, type-II process is also affected by the available oxygen. Higher light intensity produces more efficient singlet oxygen, resulting a higher transient efficacy, in which all intensities reach the same SSE when oxygen is completely depleted. With external oxygen, type-II efficacy increases with time, otherwise, it is governed only by the light dose, i.e., same dose achieves same efficacy. Moreover, type-II has an efficacy follows Bunsen Roscoe law (BRL), whereas type-I follows non-BRL. The measured type-I efficacy and gelation profile are analyzed by our analytic formulas. Schematics of the photocrosslinking stage defined by the availability of oxygen is developed, where both type-I and –II coexist until the oxygen is depleted. The overall efficacy may be enhanced by resupply of PS or oxygen during the light exposure. The roles of light dose and PS concentration on the efficacy of photoinitiated polymerization should be are governed a new concept of a volume efficacy (Ve), defined by the product of the crosslink (or gelation) depth (CD) and local [efficacy].

The genus Euonymus (L.) consists of shrubs or woody plants, distributed mainly in the Northern Hemisphere. To date, from Euonymus spp. several hundreds of different secondary metabolites have been isolated and identified. In addition, fatty oil was found in the fruits of some species of these plants, which accumulates not only in the seeds, but also in the arils. This study presents the research of unique long-term (ten-year-old) suspension cell cultures of Euonymus maximoviczianus Prokh. which were obtained from arils of unripe capsules. Suspension cells retain the ability to form oil droplets containing neutral lipids, both in the dark and in the light, the cells are able to synthesize very-long-chain fatty acids (VLCFAs), and can synthesize delphinidin-3-O-hexoside, cyanidin-3-O-hexoside, and peonidin-3-O-hexoside. Here, we research of the fatty acid, VLCFA, and anthocyanin biosynthesis dynamics in the subcultivation, as well as the influence of methyl jasmonate (MeJa) on these processes in the dark- and under-light-grown cell cultures. In the darkness, the formation of VLCFAs is more intense, and the biosynthesis of anthocyanins is significantly activated in the light. MeJA substantially enhances the biosynthesis of anthocyanins in the light and, surprisingly, the formation of VLCFAs in the darknss. In connection with the commonality of the cytosolic pool of malonyl-CoA, which is necessary both for the biosynthesis of VLCFAs and dihydroflavonols (and, ultimately, anthocyanins), the competition of these biosynthetic pathways is discussed.

Heavy metal contamination is listed among the most alarming threats to the environment and human health. The detrimental effects of heavy metals in the natural environment span from a reduction of biodiversity to toxic effects on marine life - through microplastic born heavy metals -, to impairment of microbial activity in the soil, and to detrimental effects on animal reproduction. A host of different chemical and biological technologies have been proposed to alleviate environmental contamination by heavy metals. Relatively less attention has been paid to the microbial precipitation of heavy metals, as a side mechanism of the most general process of microbially induced calcite precipitation (MICP). This process is currently receiving a great deal of interest from both a theoretical and practical standpoint, because of its possible practical applications in concrete healing and soil consolidation, and its importance in the more general framework of microbial induced mineral precipitation. In this study, we analyse the ability of the marine bacteria Vibrio harveyi in co-precipitating CaCO3 minerals, together with Cd, Cr, Pb, and Zn added in form of nitrates, from solutions containing CaCl2. The precipitated carbonatic minerals were a function of the different heavy metals present in the solution. The process of co-precipitation appears to be rather effective and fast, as the concentrations of the 4 heavy metals were reduced in 2 days by 97.2%, on average, in the solutions.

Globally,coastal regions are vital areas of human activities and, as such, are centres of population growth and urban and economic development. Long-term human development has had a major impact on the ecological environment of coastal zones. Therefore, exploring the distribution and provenance of marine sediment types in coastal areas heavily influenced by human activities can provide scientific evidence and references for the current and future ecological management of these sensitive environments. For this reason, we have conducted an analysis on the sediment grain size, Endmember, organic matter content and geochemical elements in the Lu’erhuan River‒Malan Island‒Sandun Island area in the eastern part of Qinzhou Bay, a region heavily influenced by human activities. Sediment grain size clearly differs throughout the study site and the material provenances and hydrodynamic conditions are also varied, likely due to the local environmental conditions and the significant impact human activities have had on the area. The finest-grained sediment is imported from either inland or coastal areas via rivers and weak tidal currents, the next finest component is input from coastal areas through weak tidal currents, and the moderately coarse component mainly originates from nearby beaches. The two coarsest-grained sediment components are influenced by the combination of human activities, tidal currents and waves and enter the water via erosion. Organic matter provenance resembles that of the sediment components, exhibiting varied characteristics. This is due to the combination of natural and human activities in the bay. The organic matter in the upper reaches of the Lu’erhuan River originates from the river and coastal paddy fields, with obvious terrigenous characteristics; the organic matter in northern Malan Island mainly comes from external sources related to oyster farming; while organic matter in eastern Sandun Island is mainly produced endogenously by marine plankton. Al, Ti, Fe, Mg, K, Ga and other elements indicate that terrestrial sediments are significantly disturbed by human activities. However，Mn reflects the marine distribution of terrestrial sediments from the Lu’erhuan River to Jishuimen. Ca and Sr, indicators of marine sediments, are distributed in the eastern offshore area of Sandun Island, which is connected to the open waters. Due to the influence of human activities, As and Cd are highly enriched in the study area, while Cu is less affected by human activities.

In the aftermath of pyroclastic-flow –dominated eruptions, lahars are the main geomorphic agent, but at the decadal scale, different sets of processes take place in the volcanic sediment cascade. At Unzen Volcano, in the Gokurakudani Gully we investigated the geomorphologic evolution and how the topographic change and the sediment change over time is controlling this transition. For this purpose, a combination of LiDAR data, aerial photography and photogrammetry, Ground Penetrating Radar and sediment grain-size analysis was done. The results show chocking zones and zones of enlargement of the gully, partly controlled by pre-eruption topography, but also by the overlapping patterns of the pyroclastic flow deposits of 1990 – 1995. The Ground Penetrating Radar revealed that on top of the typical lahar structure at the bottom of the gully, side-wall collapses were trapping finer sandy sediments formed in relatively low-energy deposition environment. This shows that secondary processes are taking place in the sediment transport process, on top of lahar activity, but also that these temporary dams may be a source of sudden sediment and water release, leading to lahars. Finally, the sediments from the gully walls are being preferentially oozed out of the pyroclastic-flow deposit, meaning that over longer period of time, there may be a lack of fines, increasing permeability and reducing internal pore-pressure needed for lahar triggering. It also poses the important question of how much of a past-event one can understand from outcrops in coarse heterometric material, as the deposit structure can remain, even after loosing part of its fine material.

Study of gross alpha (GA) and gross beta (GB) activity in road and surface deposited sediments were performed in various geographical areas in three Russian cities. To perform radiation measurements, new methods were applied which allow dealing with low mass and low volume dust size (2-100μm) samples obtained after the size fractionation procedure. The 2-10 μm fraction size has the highest gross beta activity concentration (GB)– 1.32Bq/g in Nizhny Novgorod (NN) and Rostov-On-Don (RND) while the 50-100 μm fraction size in Ekaterinburg. This is maybe associated with the subsistence of radionuclides that conveyed through natural processes and anthropogenic applications. The highest gross alpha activity concentration (GA) in fraction sizes was found in Rostov-on-Don city within the 50-100 μm– 0.22Bq/g. The fraction size 50-100 μmhas a higher gross alpha activity concentration than 2-10 and 10-50 μmfraction sizes due to natural partitioning of the main minerals constituting the urban surface deposited sediment (USDS). The geochemical processes that occur during the formation and transportation of USDS are reflected in the observed dependencies.Developed experimental methods of radiation measurements allowed to the extent the methodological base of urban geochemical studies.

The application of geophysical methods for the characterization of geomorphologic subsurface features has become very popular in recent years. Convential geophysical applications on undifferentiated and weathered slopes have been less effective. Multichannel analysis of surface waves (MASW) is a new hope for the solution of the problem. MASW methods was used to the first step in order to reconstruct the ancient eruption of Mount Samalas. MASW was applied to the remnants of ancient volcanic sediment on Lombok Island to determine the physical and physical characteristics of seismic subsurface features. This paper is also discussion the application's capabilities of the MASW method on undifferentiated and weathered volcanic deposits on the slope area and classified them. The results of the research show that MASW technique is powerful in characterizing and delineating the stratum of the layers of undifferentiated and weathered volcanic precipitation areas. MASW is able to predict subsurface structures, especially for shallow and thin layers and presenting site class information for internal structure (vertical resolution). Based on S wave velocity structure, undifferentiated and weathered volcanic layer, genes are classified into site class C, D, and E. In the future, this method will completed with combination of other geophysical method and parameters variation (frequency and spaces) for isopach mapping of volcanic sediment and then analysis of ancient volcanic eruption dynamics.

Endothall dipotassium salt and monoamine salt are herbicide formulations used for controlling submerged aquatic macrophytes and algae in aquatic ecosystems. Microbial activity is the primary degradation pathway for endothall. To better understand what influences endothall degradation, we conducted a mesocosm experiment to 1) evaluate the effects of different water and sediment sources on degradation, and 2) determine if degradation was faster in the presence of a microbial community previously exposed to endothall. Endothall residues were determined with LC-MS at intervals to 21 days after endothall application. Two endothall isomers were detected. Isomer-1 was abundant in both endothall formulations, while isomer-2 was only abundant in the monoamine endothall formulation and was more persistent. Degradation did not occur in the absence of sediment. In the presence of sediment degradation if isomer-1 began after a lag phase of 5-11 days and was almost complete by 14 days. Onset of degradation occurred 2-4 days sooner when the microbial population was previously exposed to endothall. We provide direct evidence that the presence and characteristics of sediment are of key importance in the degradation of endothall in an aquatic environment, and that monoamine endothall has two separate isomers that have different degradation characteristics.

As a photo-catalytic titanium oxide film deposition process, thermal spray is hoped to be utilized practically on the condition that it is relatively easy to deposit anatase rich films. However, because of its high equipment and feedstock powder costs, it is very difficult to introduce thermal spray equipment into small companies. In this study, to develop a low cost thermal spray system, low power atmospheric suspension plasma spray equipment with titanium hydroxide suspension created by hydrolysis of titanium tetra iso butoxide using Ar, N2 as working gases. For avoiding sedimentation of the hydroxide particles in the suspension, mechanical milling of the suspension was conducted to create colloidal suspension before using it as feedstock. Moreover, an Ultrasonic wave container was used to keep the suspension particles moving while the spray process was conducted. After the film deposition, with As for the coating, anatase rich TiO2 film could be obtained. For characterization of the film, microstructure observation by optical microscope and X-ray diffraction was carried out. Consequently, by creation of colloidal suspension, deposition could be conducted without sedimentation of the hydroxide particle in the suspension during operation. Besides, it was proved the film had enough photo-catalytic property to decolor methylene-blue droplet

The exponential growth in the consumption of electronics, in combination with the reduction in their useful life, leads to a significant increase in the volume of electronic material discarded. Printed Circuit Boards (PCBs) are modules composed of ceramic, polymer and metallic materials of high economic value and with a great potential for damage to biotic and anthropic environments when inadequately discarded. The aims of this work was to study the main environmental impacts and the efficiency of mechanical operations in the electronic waste recycling process in optimizing the concentration of metallic copper. For this, the samples obtained were characterized according to their morphology and chemical composition, and subjected to physical and mechanical treatments: dismantling, grinding, separation by granulometry, density and magnetic property. The environment impacts were estimated by the Life Cycle Assessment of the pre-treatment processes, associated with copper extraction operations in WPCBs. According to the results obtained, it is possible to infer that the NM +1mm Concentrated product presents in its metallic composition around 78% of copper, which contributes to the efficiency of the hydrometallurgical extraction processes. It is noteworthy that the Concentrated class represents about 14% of copper (wt) taking into account the amount of 3.789 kg of PCB waste input material. The potential for reinsertion of the dust in the material recovery process is highlighted, given that the chemical composition of this particulate has a significant presence of metals. In general, it was found that due to the higher concentration (wt %) of the sample being allocated in the range of - 0.15mm + 0.05mm, the elements Fe (18.30%), Si (10.73%), Ca (9.21%) and Cu (8.89%) stand out regarding the participation of the elemental composition of this fraction and also regarding the general composition of the sample. Furthermore, the generation of dust during the fragmentation process, can be associated with occupational respiratory diseases when not managed. About the Life Cycle Assessment, in seven of the nine categories evaluated, crushing and screening activities accounted for more than 90% of the recorded impact values. In general, it is estimated that in the pre-treatment phase be generated 15.4 kg CO2 eq.

Minerals play many important functions in plant and animal metabolism. Therefore, we investigated the concentration of Se and other minerals and their relationships in soils and fodder plants in Kosovo. Seventy-three samples of each soil and fodder plants (grass, maize, and wheat) from 30 farms were collected. Both soil and plant samples, after processing and digestion, were analyzed for mineral concentration by ICP-MS. Mineral concentrations in soil and fodder crops, and the best predicting/explanatory models for micro minerals concentration, achieved by stepwise linear regression, are presented. Results showed very low concentration of Se in most of the soil and all fodder samples. In addition, the concentration of Co, Zn and Fe was not sufficient to satisfy requirements for all categories of farm animals. Plant Se concentration showed a positive relationship with Se concentration in soils. Plant Zn, Mo, Mn, Fe and Pb, in general, showed no significant relationship with their concentration in soil, while plant Co and Cd showed positive relationship only in maize, and Cu in wheat grain. Among the soil properties, pH had the highest effect on the concentrations of Co, Mo, Mn, Cd and Pb in fodder crops.

As a major coal country, China faces the issue of significant gas emissions during the coal mining process. This study aims to improve the utilization efficiency of mine gas, reduce greenhouse gas emissions, and promote the low-carbon and green transformation of the coal industry. A 10kW gas regenerative thermal oxidation (RTO) experimental system was constructed. The effects of initial methane concentration, low-temperature flue gas proportion, and operating load on combustion temperature, methane oxidation rate, high-temperature flue gas energy, and system thermal efficiency were studied. The results show that when the combustion temperature is below 600°C, the CH4 combustion reaction cannot proceed effectively, and the system temperature continuously decreases and cannot be maintained stable. The experiment determines the stable operating methane concentration range of RTO. In this experimental system, the lower limit of the initial methane concentration is 0.28%, corresponding to an 86% methane oxidation rate. As the initial methane concentration decreases, the combustion temperature also decreases, and the methane oxidation rate follows suit. The higher the low-temperature flue gas proportion, the higher the combustion temperature, and the system thermal efficiency and output heat decrease with the increase of the low-temperature flue gas proportion. This experiment explores multiple factors affecting regenerative thermal oxidation, providing an basis for ensuring the safe and stable operation of the system and optimization. Improving the thermal insulation and heat exchange performance of the storage body can expand the lower limit of the initial methane concentration, thereby increasing the stability and thermal efficiency of the system.

The use of antibiotics grown promoter has been banned, due led problems with drug residues in animal products and increased bacterial resistance. For several reasons there is a growing interest in the scientific community in immunoglobulin Y as antibiotic alternative and their oral administration in the polyclonal antibody (pAb) format, to maintain animal health and performance, do not require IgY purification for large-scale production, resulting in protein impurities and high concentration of biotin in the samples. The signal amplification through non-covalent interaction of biotin with streptavidin has been extensionally used by many laboratories for several diagnosis diseases and scientific research in enzyme-linked immunosorbent assay (ELISA). However, the riches sources of biotin as egg yolk, leading to high biotin concentrations in samples, harming the accuracy of diagnostic and proteins concentrations tests. This study aimed to evaluate the biotin influence on measurement of Immunoglobulin Y in egg yolk freeze dried samples from immunized laying hens by immunoassays using biotin-avidin/streptavidin. The IgY concentration changed down in immunoassays using biotin-avidin/streptavidin. The detection of IgY in yolk samples by ELISA using streptavidin–biotin binding as part of the assay methodology requires some technology to neutralize high concentration of biotin on sample or more steps beyond delipidation to isolate the target protein. Otherwise, an ELISA without the use of streptavidin-biotin binding would be more advisable to avoid biotin and targets protein relationship and prevent biotin interference on results.

Using the unique combination of atomically resolved atom probe tomography (APT) and volume averaged neutron (resonance) spin echo (NRSE and NSE) experiments, the influence of nano-scaled clusters on the spin relaxation in spin glasses was studied. For this purpose, the phase transition from the paramagnetic phase to the spin glass phase in a Fe-Cr spin glass with a composition of Fe_17.8Cr_82.2 was studied in detail by means of NRSE. The microstructure was characterised by APT measurements, which show local concentration fluctuations of Fe and Cr on a length scale of 2 to 5 nm, which lead i) to the coexistence of ferro- and anti-ferromagnetic clusters and ii) a change of the magnetic properties of the whole sample, even in the spin glass phase, where spins are supposed to be randomly frozen. We show that a generalized spin glass relaxation function, which was successfully used to describe the phase transition in diluted spin glasses, can also be used for fitting the spin dynamics in spin glasses with significant concentration fluctuations.

Glutamine is the main amino acid which is substrate for gluconeogenesis in postoperative period. It is suggested that this leads to a substantial and a long-term decline in glutamine concentration. Glutamine is a source of energy for the synthesis of nucleotides, lymphocytes and cells of gastrointestinal tract. In this study, 79 patients were qualified to a coronary artery bypass surgery (Group I) or a surgery in the large intestine area (Group II). The objectives of this study were: evaluation of the impact of surgical procedures on the serum concentration of glutamine of the operated patients, assessment of gender, weight and BMI impact on glutamine concentration and analysis of the correlation between glutaminę serum concentration and laboratory parameters. The mean concentration of glutamine before surgery, the 3rd and 5th day after surgery was higher in Group I. CRP level in the 3rd and 5th postoperative day was higher in Group II. There were no significant differences betweengroups when it comes to BMI and the concentration of CRP (p <0.05). Glutamine concentration depends on the severity of inflammation, the operated body cavity and the intensified catabolism which results from different pathophysiology of digestive system diseases and coronary arterial disease.

: Nonylphenol is an endocrine disruptor who belongs to alkylphenol group of chemicals and its high occurrence in the environment can caused an adverse effect on human health. The breast milk can serve as a marker to take measure of human exposure to these chemicals through different routes of exposure. In this study, the influence of different factors (kind of wastes mothers drink, consummation of fish, pork and beef; using gloves, mail polish, using vitamins and medication) on the concentration on nonylphenol in breast milk were studied. Concentrations of nonylphenol in breast milk were determined by high-performance liquid chromatography (HPLC) with fluorescence detection. The lowest and highest concentration of nonylphenol in breast milk was 0.97 ng/mL and 4.37 ng/mL, respectively. The selected factors such as pork, beef, fish consumption, vitamin supplementation, medication, using of gloves, nail polish and gel nails were observed in relation to 4-nonylphenol concentration.

In light of the hazardous effects of global warming brought on by climate change, bioethanol production is one of the key alternatives in which the world has expressed a great deal of interest. Two factors—indigenous production and price—are crucial for bioethanol to be appealing in Africa and, for that matter, Ghana. The objective of this research is to produce bioethanol from cheap lignocellulosic materials using onsite enzymes produced from cassava peels degrading fungi. Due to Ghana's prominent position as one of the leading cassava producers in the world, the study focused on utilizing cassava peels, which are underutilized in the country. The research was conducted in multiple stages. In the first stage, the peels were prepared by washing, drying, and manually crushing them using mortar and pestle. The second stage involved analyzing the chemical composition of the peels, including starch and insoluble fibre, which were determined as Acid Detergent Fiber (ADF), Neutral Detergent Fiber (NDF), and Acid Detergent Lignin (ADL). The results showed significant levels of cellulose (39.78%) and starch (31.21%), indicating that cassava peels are valuable raw materials for bioethanol production. The content of hemicellulose (21.11%) and lignin (3.84%) were also determined. In the third stage, using a Petri dish, three fungi (ICPF1, ICPF2, and ICPF3) were isolated from two different cassava peels. ICPF1 was only identified from fresh cassava peels (FCP), while all three fungi were identified from decayed cassava peels (DCP). Morphologically, these fungi were identified as Aspergillus niger, Aspergillus flavus, and Rhizopus stolonifer. The fourth stage focused on optimizing the enzyme activity of the three isolates for potential applications, with A. niger demonstrating the highest enzyme activity with a diameter of zone of clearance of 16 mm. Stage five involved optimizing the production of the onsite enzyme in a 50ml flask using A. niger, basal salt medium (BSM), and cassava peels as a substrate. The DNSA method was used to measure the absorbance of maltose and glucose at 540 nm for various substrate concentrations (1%, 3%, 5%, 8%, and 10%) at specific intervals of 2, 4, 6, 8, and 10 days with a spore concentration of 2.1 x 105 cells/ml. The maltose and glucose concentrations were calculated as 7.138mg/ml and 6.398 mg/ml, respectively, and the corresponding enzyme activity was determined as 4.759U/ml and 4.265U/ml. The optimal conditions of Day 4 and a substrate concentration of 10%, along with a fixed temperature of 30°C and a pH of 5.5, were used to prepare the onsite enzymes in a 500 ml flask for the fermentation process. The onsite enzymes were used for saccharification and Saccharomyces cerevisiae for fermentation under simultaneous saccharification and fermentation (SSF) process. A mixture of 20 ml of onsite enzymes and 1.5 g of S. cerevisiae were added to substrate concentrations of 5%, 10%, and 20%, and the ethanol concentration was analyzed daily for 7 days using Gas Chromatography (GC). The highest ethanol concentration (1.316%) was observed on Day 5 with a substrate concentration of 20%, while the lowest concentration (0.123%) was recorded on Day 1 with a substrate concentration of 5%.

This paper investigates the impact of sediment deposition and inflow conditions on horizontal impact pressure and frequency analysis of bridge deck vibrations during flooding. Flooding-induced pressure and vibrations contribute to bridge collapse, and sediment deposition influences water flow and impact pressure. The study explores the relationship between sediment deposition height and impact pressure, revealing a significant increase as sediment approaches 50% of bridge deck clearance. Sediment amplifies impact pressure response to flow velocity changes. The dimensionless sediment deposition height has a greater influence on impact pressure compared to the inflow Froude number. Two distinct frequencies, dominant and secondary, are identified for impact pressure and water level fluctuations. Dominant frequencies positively correlate with sediment deposition height and Froude number, indicating an increasing trend. Secondary frequencies remain stable (0.31-0.58 Hz). These findings enhance understanding of flow dynamics and bridge-flow interaction in sediment-deposited channels, providing theoretical support for evaluating and managing disasters related to bridges in such environments. Overall, this research contributes to the field of bridge engineering and supports improved design and maintenance practices for bridges exposed to sediment-deposited channels.

The detection of antibiotic-resistant facultative pathogenic bacteria in surface waters is common in the present day. However, there is limited understanding of the factors that influence the spread and stabilization of resistance in this habitat, particularly regarding the role of biofilms. Despite the perceived differences between sediments, biofilms, and open water, their potential contribution to the long-term maintenance of resistances remains unclear. In this study, we investigated Escherichia coli isolates obtained from the Mur and Drava rivers in Austria. Samples were collected from both the water column and sediment at two locations per river: upstream and downstream of an urban area, including a sewage treatment plant. The iso-lates were subjected to antimicrobial susceptibility testing against 21 antibiotics belonging to seven distinct classes. Additionally, any isolates exhibiting an extended-spectrum beta-lactamase (ESBL) or carbapenemase phenotype were further analyzed for the presence of specific antimi-crobial resistance genes. E. coli isolates obtained from the two rivers exhibited resistance to at least one of the tested anti-biotics, with rates of 25.83% and 23.66% respectively. The most prevalent antimicrobial re-sistances observed were towards ampicillin, amoxicillin-clavulanic acid, tetracycline, and na-lidixic acid. Surprisingly, there was a similar proportion of resistant bacteria observed in both open water and sediment samples, contrary to expectations. The difference in resistance levels between samples collected upstream and downstream of the cities was minimal. Out of the total isolates, 13 E. coli were found to carry ESBL genes with one isolate carrying the gene for KPC-2 carbapenemase. There were no significant differences between the biofilm (sediment) and open water samples in the occurrence of antimicrobial resistance. Even the difference between the samples upstream and downstream of the cities and their wastewater treatment plants was minor. There seems to be no evidence of a large adaptive effect in this analysed biofilm population of E. coli. The un-typical phenotype of the KPC-producing and some of the ESBL-producing E. coli from this study could, however, be an indication that such adaptation effects generally exist in water.

A conventional 2D numerical model is improved by incorporating three submodels to consider different effects of secondary flow and a module for cohesive sediment transport. The model is applied to a meandering reach of Yangtze River to investigate secondary flow effects on cohesive sediment deposition, and a preferable submodel is selected based on the flow simulation results. Sediment simulation results indicate that the improved model predictions are in better agreement with the measurements in planar distribution of deposition as the increased sediment deposits caused by secondary current on the convex bank have been well predicted. Secondary flow effects on predicted amount of deposition become more obvious during the period when the sediment load is low and velocity redistribution induced by the bed topography is evident. Such effects vary with the settling velocity and critical shear stress for deposition of cohesive sediment. The bed topography effects can be reflected by the secondary flow submodels.

This paper is about to estimate the suspended sediment transport amount in the streams flowing into the Sapanca Lake Basin. There are 12 subsidiary streams flowing into the Sapanca Lake Basin. With the aim of estimating the suspended sediment transport in 2012-204 in these subsidiary streams, measurements belonging the parameters such as level, cross sectioning, flow rate, temperature and suspended sediment were made monthly. Along the measurement period, weather conditions were above seasonal normal and precipitations decreased. In order to estimate the suspended sediment amount by using results of the measurement obtained, Artificial Neuron Network (ANN), Sediment Rating Curve (SRC) and Multiple Linear Regression (MLR) models were used for different scenarios. It was seen that artificial neuron networks yielded the most accurate results among the models.

The variation of river hydrologic process can not only reflect the impact of natural factors, but also the impact of human activities. The purpose of this study is to reveal the change trend of the hydrologic regime of the Yellow River and its response to ecological protection in the river basin. Based on the daily water and sediment observation data of representative gauging stations in the middle and lower reaches of the Yellow River, it was analyzed the variation trend of the annual and monthly runoff and suspended sediment load (SSL), and monthly mean runoff, suspended sediment transport rate (SSTR), sediment inflow coefficient, and hydrological regime in decadal average of the gauging stations during the period 1960-2019. The results show that the variation of annual runoff and SSL, as well as the monthly mean runoff and SSTR in decadal average, has a significant decreasing trend in the 1960’s-1990’s, which was mainly in response to the gradual implementation of ecological protection measures such as afforestation, grass planting, terrace construction, and check dam construction, etc. in the basin. In 2000’s and 2010’s, the annual runoff increased, while the SSL increased slightly. This was a response to the implementation of new river management measures such as ensuring the ecological water demand of the lower reaches and scouring the riverbed by manually regulated clear water discharged from the Xiaolangdi Reservoir. In the same time, the monthly mean runoff and SSTR for the flood season (Jun.-Oct.) decreased remarkably, while the process curve of the monthly mean discharge and sediment concentration, changed from a clockwise loop to a counterclockwise loop in the river reach below the Xiaolangdi dam. This was a comprehensive response to the environmental protection measures in the Yellow River basin, in which the construction and operation of the Xiaolangdi Reservoir played a key role. This study can provide reference for river basin management.

Microalgae are highly attractive to various industrial sectors and can serve as indicators of aquatic environmental health. An essential step for cultivating microalgae is assessing the cell density, which is traditionally performed through viable cell counting by optical microscopy (OM). However, this method has some limitations, such as the time involved in the process of counting, and the need for specialized training of laboratory personnel. Spectrophotometry is an affordable alternative, especially when applied to culture growth and toxicological tests. We chose the wavelength of 680 nm to detect the optical density (OD) of the green freshwater microalga Desmodesmus subspicatus and green the marine microalga Tetraselmis sp. The correlation between the number of cells and OD was suitable for both microalgae and accuracy was comparable to traditional OM counting. In toxicological tests, the OD technique allowed the monitoring of microalgal growth in the presence of the chemicals potassium dichromate, potassium chloride and sodium dodecyl sulfate (SDS), with results very close to those reported in the scientific literature. This study sheds light on this well-known technique, which is an important contribution since few articles have explored its potentialities and fragilities, showing the successful application to monitoring green microalgal cultures and toxicological assays.

Gymnema sylvestre is a pharmacological plant which has a rich source of bioactive compounds specifically gymnemic acid (GA) and phenolic compounds (PC) that used for pharmaceutical industries. Sources for naturally occurring bioactive compounds are limited, due to geographical and seasonal variations; on the other hand, it is commercially in demand. Biosynthesis of G. sylvestre phytochemicals through in vitro culture often enhanced by elicitation. The use of cell suspension cultures (CSC) has interested serious attention on the production of essential phytochemicals. The current study is aimed at improving the contents of GA and PC in G. sylvestre CSC using the copper oxide nanoparticles (CuO NPs). Callus was obtained on MS medium with 2.0 mg/L 2,4-dichlorophenoxyacetic acid (2,4-D), 0.1 mg/L kinetin (KIN), phytoagar (8.0 g/L), and sucrose (30 g/L). The above medium devoid of agar was used for the initiation of CSC. The CSC was treated with three levels of CuO NPs (1, 3 or 5 mg/L) to enhance the production of GA and PC. The greatest amount of GA (89.25 mg/g dry cell mass, DCM), total phenolic (245.10 mg/g), and flavonoid (4.57 mg/g) in CSC were achieved when G. sylvestre cells were treated for 48 h with 3 mg/L CuO NPs. Also, the biomedical potential (antioxidant, antidiabetic, anti-inflammatory, antibacterial, antifungal and anticancer activities) were also high in the CuO NPs (3 mg/L) treated CSC extracts of G. sylvestre. CuO NPs elicitation of CSC significantly increased production of GA (9-fold), and PC than non-elicited CSC in G. sylvestre.

In this study, different configurations based on linear fiber lasers were proposed and experimentally demonstrated to measure the concentration of paracetamol liquid solutions in a range of 52.61 to 201.33 g/kg. The optical gain was provided by a commercial bidirectional Erbium-Doped Fiber Amplifier (EDFA) and the linear cavity was obtained using two commercial Fiber Bragg Gratings (FBGs). The main difference of each configuration was the coupling ratio of the optical coupler used to extract the system signal. The sensing head corresponded to a Single-Mode Fiber (SMF) tip that worked as an intensity sensor. The results reveal that, despite the optical coupler used (50:50, 60:40, 70:30 or 80:20), all the configurations reached the laser condition, however, the concentration sensing was only possible using a laser drive current near to the threshold value. The configurations using a 70:30 and an 80:20 optical coupler allowed to perform paracetamol concentration measurements with a higher sensitivity of (-3.00±0.24) pW/(g/kg). In terms of resolution, the highest value obtained was 1.75 g/kg, when it was extracted 20% of the output power to the linear cavity fiber laser configuration.

Ion current rectification (ICR) is the ratio of ion current by forward bias to by backward bias and is a critical indicator of diode performance. In previous studies, many attempts have been continued to improve the performance of this ICR, but there is the intrinsic problem for geometric changes that induce ionic rectification due to their fabrication problem. Additionally, the high ICR could be achieved in the narrow salt concentration range only. Here, we propose a multi-layered bipolar ionic diode based on an asymmetric nanochannel network membrane (NCNM), which is realized by soft lithography and self-assembly of homogenous-sized nanoparticles. Owing to the freely changeable geometry based on soft lithography, the ICR performance can be explored according to the variation of microchannel shape. Interestingly, very stable ICR performance can be achieved using the multi-layered 3D configuration for the bipolar diode in a broad range of salt concentrations (0.1mM ~ 100 mM). This demonstrates the promising potential of multi-layered NCNM for applications in highly concentrated electrolytes, such as biosensors, desalination, or energy harvesting.

(1) Background: Health Care-Associated Infections (HAIs)are a significant public health problem worldwide favoring multidrug-resistant (MDR) microorganisms. The SARS-CoV-2 infection had a negative association with the increase in antimicrobial resistance, and the ESKAPE group had the most significant impact on HAIs. The study aimed to evaluate the bactericidal effect of high concentration O3 gas on some reference and ESKAPE bacteria. (2) Material and Methods: Four standard strains and four clinical or environmental MDR strains were exposed to high ozone doses at different concentrations and times. Bacterial inactivation (growth and cultivability) was investigated using colony counts and resazurin as a metabolic indicator. Scanning electron microscopy (SEM) was performed. (3) Results: The culture exposure to a high level of O3 inhibited the growth of all bacterial strains tested with a statistically significant reduction in colony count compared to the control group. The cell viability of S. aureus (MRSA) (99,6%) and P. aeruginosa (XDR) (29,2%) was reduced considerably, and SEM showed damage on bacteria after O3 treatment (4) Conclusion: High doses of ozone were able to interfere in the growth of all strains studied, evidencing that ozone-based decontamination approaches may represent the future of hospital cleaning methods.

Microalgal harvesting is one of the most challenging processes in the development of algal research and development. Several methods, such as centrifugation, flocculation, and filtration, are available at the laboratory scale. However, the requirement of expensive pieces of equipment and the possibility of biomass contamination are recurring gaps that hinder the development of microalgae I+D in different parts of the world. Recently, the electroflotation has been proved as a suitable method for the harvesting of different species of microalgae and cyanobacteria. To this day, there are no companies that sell laboratory-scale electroflotation equipment; this is mainly due to the gap in the knowledge on which factors (time, mixing rate, number of electrodes, and others) will affect the efficiency of concentration without reducing the biomass quality. This paper aims to build an innovative low-cost electroflotation system under 300 USD with cheap and resistant materials. To achieve our goal, we test the interaction of three variables (time, mixing rate, and amount of electrodes) were evaluated. Results showed that an efficiency closer to 100% could be achieved under 20 minutes using >10 electrodes and 150 rpm. We hope this innovative approach can be used by different researchers to improve our knowledge of the concentration and harvesting of algae and cyanobacteria.

Crop digital twin is redefining traditional farming practices, offering unprecedented opportunities for real-time monitoring, predictive and simulation analysis, and optimization. This research embarks on an exploration of the synergy between precision agriculture, crop modeling, and regression algorithms to create a digital twin for augmenting farmers the concentration and composition prediction-based crop nutrient recovery. This captures the holistic representation of crop characteristics, considering the intricate relationships between environmental factors, nutrient concentrations, and crop compositions. However, the complexity arising from diverse soil and environmental conditions makes nutrient content analysis expensive and time-consuming. This paper presents the result of a predictive digital twin case study that employs six regression algorithms namely Elastic Net, Polynomial, Stepwise, Ridge, Lasso, and Linear Regression to predict rice nutrient content efficiently, particularly considering the coexistence and composition of multiple nutrients. Our research findings highlight the superiority of the Polynomial Regression model in predicting nutrient content, with a specific focus on accurate nitrogen percentage prediction. This insight can be used for nutrient recovery intervention by knowing the precise amount of nutrient to be added into the crop medium. The adoption of the Polynomial Regression model offers a valuable tool for nutrient management practices in the crop digital twin, potentially resulting in higher-quality rice production and a reduced environmental impact. The proposed method can be replicable in other low-resourced crop digital twin system.

Overuse and misuse of antibiotics can pose the risks of spreading mutant strains that show antimicrobial resistance (AMR), with negative impact on management of bacterial infections and economic implications on healthcare systems. Research and development of natural antibacterial agents could be a priority in the next years to improve number of effective antibacterial molecules and to reduce AMR phenomenon and its development. The present study identified the most effective concentration and contact time of Thymus vulgaris L. essential oil (TEO) to obtain bactericidal effect in vitro against different Gram + and Gram – bacterial strains. Six clinically isolated (wild types) bacterial strains, (Citrobacter freundii, Enterococcus feciorum, Proteus mirabilis, Acinetobacter cioffi, Pasteurella putrefaciens, Klebsiella pneumoniae) and two ATCC (Staphylococcus aureus and Streptococcus mutans) were tested after 1min, 3min and 5min of contact with TEO. Preliminary results on S. aureus after 24h incubation revealed a TEO concentration of 9.28mg/mL (w/v) that completely inhibited bacteria growth keeping cell viability. Total suppression of bacterial growth at all tested contact times was observed for all tested bacterial strains and the results were confirmed after 48h incubation. Bacterial growth suppression was confirmed even with presence of organic component. These preliminary results showed in vitro antimicrobial efficacy of TEO against different Gram+ and Gram- bacterial strains. Future studies are necessary to confirm the reproducibility of these results even on other strains and to define exactly the molecular mechanisms of EOs, in order to consider TEO as a valid alternative of classic antibiotic therapies and subsequently to reduce the occurrence of AMR.

The threat of fine particulate matter concentration (PM2.5) is increasing globally, Tackling this issue requires an accurate understanding of its trends and drivers. The article investigates the PM2.5 characteristics of 285 prefecture-level cities in China from 2000-2018 based on multiscale geographically weighted regression(MGWR), and the results show that（1）previous studies based on classical MGWR models may be somewhat unstable, while MGWR can reflect the scale of influence of different variables on the dependent variable, and its regression results are more reliable.（2）PM2.5 is very sensitive to carbon emission(CE) factors, and there is a high degree of spatial heterogeneity, and the influence scale of location is the smallest among all variables, close to the municipal scale.（3）In 2000, the constant term all, IS, OFT, CE, and LT positively affect PM2.5, while GDP (jurisdiction) and UR negatively affect PM2.5; in 2010, the constant term all, GDP (jurisdiction), IS, OFT and LT positively affect PM2.5, while UR and CE negatively affect PM2.5; in 2018 the constant term all, IS, OFT and CE factors positively affect PM2.5, and GDP (jurisdiction), UR and LT negatively affect PM2.5.